1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
Advances in knitting technology
i © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
The Textile Institute and Woodhead Publishing The Textile Institute is a unique organisation in textiles, clothing and footwear. Incorporated in England by a Royal Charter granted in 1925, the Institute has individual and corporate members in over 90 countries. The aim of the Institute is to facilitate learning, recognise achievement, reward excellence and disseminate information within the global textiles, clothing and footwear industries. Historically, The Textile Institute has published books of interest to its members and the textile industry. To maintain this policy, the Institute has entered into partnership with Woodhead Publishing Limited to ensure that Institute members and the textile industry continue to have access to high calibre titles on textile science and technology. Most Woodhead titles on textiles are now published in collaboration with The Textile Institute. Through this arrangement, the Institute provides an Editorial Board that advises Woodhead on appropriate titles for future publication and suggests possible editors and authors for these books. Each book published under this arrangement carries the Institute’s logo. Woodhead books published in collaboration with The Textile Institute are offered to Textile Institute members at a substantial discount. These books, together with those published by The Textile Institute that are still in print, are offered on the Woodhead web site at: www.woodheadpublishing.com. The Textile Institute books that are still in print are also available directly from the Institute’s website at: www. textileinstitutebooks.com. A list of Woodhead books on textile science and technology, most of which have been published in collaboration with The Textile Institute, can be found on pages xiii to xviii.
ii © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
Woodhead Publishing Series in Textiles: Number 89
Advances in knitting technology Edited by K. F. Au
iii © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
Published by Woodhead Publishing Limited in association with The Textile Institute Woodhead Publishing Limited, 80 High Street, Sawston, Cambridge CB22 3HJ, UK www.woodheadpublishing.com Woodhead Publishing, 1518 Walnut Street, Suite 1100, Philadelphia, PA 19102-3406, USA Woodhead Publishing India Private Limited, G-2, Vardaan House, 7/28 Ansari Road, Daryaganj, New Delhi – 110002, India www.woodheadpublishingindia.com First published 2011, Woodhead Publishing Limited © Woodhead Publishing Limited, 2011 The authors have asserted their moral rights. This book contains information obtained from authentic and highly regarded sources. Reprinted material is quoted with permission, and sources are indicated. Reasonable efforts have been made to publish reliable data and information, but the authors and the publisher cannot assume responsibility for the validity of all materials. Neither the authors nor the publisher, nor anyone else associated with this publication, shall be liable for any loss, damage or liability directly or indirectly caused or alleged to be caused by this book. Neither this book nor any part may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying, microfilming and recording, or by any information storage or retrieval system, without permission in writing from Woodhead Publishing Limited. The consent of Woodhead Publishing Limited does not extend to copying for general distribution, for promotion, for creating new works, or for resale. Specific permission must be obtained in writing from Woodhead Publishing Limited for such copying. Trademark notice: Product or corporate names may be trademarks or registered trademarks, and are used only for identification and explanation, without intent to infringe. British Library Cataloguing in Publication Data A catalogue record for this book is available from the British Library. ISBN 978-1-84569-372-5 (print) ISBN 978-0-85709-062-1 (online) ISSN 2042-0803 Woodhead Publishing in Textiles (print) ISSN 2042-0811 Woodhead Publishing in Textiles (online) The publisher’s policy is to use permanent paper from mills that operate a sustainable forestry policy, and which has been manufactured from pulp which is processed using acid-free and elemental chlorine-free practices. Furthermore, the publisher ensures that the text paper and cover board used have met acceptable environmental accreditation standards. Typeset by RefineCatch Limited, Bungay, Suffolk, UK Printed by TJI Digital, Padstow, Cornwall, UK
iv © Woodhead Publishing Limited, 2011
Contents
Contributor contact details Woodhead Publishing Series in Textiles
xi xiii
Part I Introduction: fundamentals of knitting
1
1
3
Types and suitability of yarns for knitting
E. Mielicka, Textile Research Institute, Poland
1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 1.11 1.12
Introduction Types of packages Structure of cope Knitting yarns defects Types of knitting yarns: yarns made of natural fibers Types of knitting yarns: yarns made of synthetic fibers Types of knitting yarns: fancy threads Yarns made for special applications Methods of joining the polyurethane yarns in composites Other yarns for special applications Future trends References
3 7 10 13 19 21 26 28 32 34 34 35
2
The physical properties of weft knitted structures
37
B. Cooke, Formerly Senior Lecturer in Knit Design (UMIST),
University of Manchester, UK
2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9
Introduction Stretch and recovery properties Recovery properties Dimensional stability Creasing Thickness and compression properties Air permeability Thermal properties Liquid transfer properties
37 38 39 40 41 42 43 43 44 v
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
vi
Contents
2.10 2.11 2.12 2.13
Comfort Pilling and abrasion Knitted fabrics with special properties Sources of further information and advice
45 45 46 47
3
Modelling of knitting
48
R. B. Ramgulam, Albany International, Bury, UK
3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9
Introduction Knitted fabric geometry Mechanics of knitted fabric: 2D model Mechanics of plain-weft knitted fabrics: 3D model Knitted fabric mechanics: energy model Knitted fabric pressure on a surface Heat and water vapour diffusion in fabrics References Appendix: initial guess estimates
48 48 51 59 66 72 80 83 84
Part II Advances in knitting
87
4
89
Intelligent yarn delivery systems in weft knitting
R. Kovar, Technical University of Liberec,
Czech Republic
4.1 4.2 4.3 4.4 4.5 4.6 4.7
Introduction Theory of yarn delivery Yarn storage and delivery systems on circular knitting machines Yarn storage and delivery systems on flat knitting machines Future trends Sources of further information and advice References
5
Advances in warp knitted fabric production
89 90 103 107 109 109 109 110
Bharat J. Gajjar, Warp Knits, Delaware, USA
5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8
Introduction Commercial warp knit machines Delaware stitch and modified Delaware stitch tricot fabrics Tricot and Raschel containing spandex Key Raschel fabrics containing spandex Newly developed constructions with spandex Americana and modified Americana tricots Surface interest fabrics
© Woodhead Publishing Limited, 2011
110 113 116 119 120 124 126 130
Contents
vii
5.9 5.10 5.11
Milanese fabrics Conclusion Sources of further information
132 135 135
6
Weft-knitted structures for industrial applications
136
M. de Araujo and R. Fangueiro, University of Minho,
Portugal and H. Hu, Institute of Textiles and Clothing, Hong Kong Polytechnic University, Hong Kong, China
6.1 Introduction 6.2 Current problems and limitations 6.3 Knitting 3D structures using weft-knitting technology 6.4 Directionally oriented structures (DOS) and combined DOS weft-knitted structures 6.5 Weft-knitted multifunctional structures 6.6 Simulating mechanical properties of weft-knitted structures 6.7 Applications 6.8 Future trends 6.9 References
136 138 141
7
171
Advances in circular knitting
148 155 157 163 167 168
D. Semnani, Isfahan University of Technology, Iran
7.1 7.2 7.3 7.4 7.5 7.6 7.7
Introduction Current problems and limitations of circular knitted structures Recent advances in circular knitting Structure and properties of circular knitted fabrics Applications Future trends: smart garments References
171
8
Knitted fabric composites
193
175 177 182 184 189 190
M. Duhovic and D. Bhattacharyya, University of Auckland,
New Zealand
8.1 Introduction 8.2 Types of fibre and yarn used in knitted fabric composites 8.3 Composite preforms 8.4 Knit structures for fabric composites 8.5 Types of matrix materials 8.6 Developments in manufacturing methods for knitted fabric composites 8.7 Mechanical properties
© Woodhead Publishing Limited, 2011
193 196 198 201 202 205 207
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
viii
Contents
8.8 8.9 8.10 8.11
Applications Conclusion Acknowledgements References
9 Quality control in the knitting process and common knitting faults K. F. Au, Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hong Kong, China 9.1 Importance of quality knitted fabric 9.2 Knitted fabric quality 9.3 Quality control in the knitting process 9.4 Parameters of knitting control 9.5 Relationship between yarn count and machine gauge 9.6 Examples of quality control mechanisms for circular knitting 9.7 Techniques to reduce knitting faults: online data monitoring system 9.8 Knitted defects 9.9 Conclusion 9.10 References
208 209 210 210 213
213 214 215 217 220 220 224 225 231 231
Part III Case studies: advanced knitted products
233
10
235
Women’s apparel: knitted underwear
J. Kar, J. Fan, and W. Yu, Institute of Textiles and Clothing,
Hong Kong Polytechnic University, Hong Kong, China
10.1 10.2 10.3 10.4 10.5 10.6 10.7 10.8
Introduction Functional requirements of knitted underwear Performance evaluation of knitted underwear Engineering of knitted underwear fabrics Recent developments in knitted underwear fabrics Properties of commercially knitted underwear fabrics Acknowledgements References
235 235 239 252 255 256 258 258
11
Knitted structures for sound absorption
262
R. M. Monaragala, Ministry of Defence, Sri Lanka
11.1 11.2 11.3 11.4 11.5 11.6
Introduction Acoustic textiles in vehicles Sound absorption of plain knitted structures Engineering advanced knitted fabrics for sound absorption Thick spacer structures Dense spacer structures
© Woodhead Publishing Limited, 2011
262 262 263 275 275 280
Contents
ix
11.7 11.8 11.9 11.10
Conclusion Future trends Sources of further information and advice References
283 284 284 285
12
Weft-knitted structures for moisture management
287
G. B. Delkumburewatte, Open University of Sri Lanka,
Sri Lanka
12.1 12.2 12.3 12.4 12.5 12.6 12.7
Introduction Basics of wetting Wicking and absorption Experimental liquid take-up Future trends Sources of further information and advice References
287 288 291 298 306 306 307
Index
309
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
x 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
Contributor contact details
(* = main contact)
Editor and Chapter 9
Chapter 3
K. F. Au Institute of Textiles and Clothing The Hong Kong Polytechnic University Hung Hom Hong Kong, China
R. B. Ramgulam Albany International Pilsworth Road Bury BL9 8RS UK E-mail:
[email protected]
E-mail:
[email protected]
Chapter 4
Chapter 1 E. Mielicka Textile Research Institute Piotrkowska 270 90-361 Lodz Poland
R. Kovar Technical University of Liberec Studentska 2 str. 461 17 Liberec Czech Republic E-mail:
[email protected]
E-mail:
[email protected]
Chapter 5
Chapter 2 B. Cooke Formerly Senior Lecturer in Knit Design (UMIST) William Lee Innovation Centre School of Materials University of Manchester M13 9PL UK
B. J. Gajjar 614 Loveville Road Building D-1F Hockessin DE 19707 USA E-mail:
[email protected]
E-mail:
[email protected]
xi © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
xii 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
Contributor contact details
Chapter 6
Chapter 10
M. de Araujo* and R. Fangueiro School of Engineering University of Minho 4800–058 Guimarães Portugal
J. Kar, J. Fan, and W. Yu Institute of Textiles and Clothing The Hong Kong Polytechnic University Hung Hom Hong Kong, China
E-mail:
[email protected]
H. Hu Institute of Textiles and Clothing The Hong Kong Polytechnic University Hong Kong, China
Chapter 7 D. Semnani Isfahan University of Technology Isfahan 84156-8311 Iran
E-mail:
[email protected] [email protected]
Chapter 11 R. M. Monaragala Chief Coordinator Electronics Wing Centre for Research and Development Ministry of Defence 15/5 Baladaksha Mawatha Columbo 03 Sri Lanka
E-mail:
[email protected]
E-mail:
[email protected] [email protected]
Chapter 8
Chapter 12
M. Duhovic* and D. Bhattacharyya Centre for Advanced Composite Materials Building 740 Tamaki Campus Morrin Road Glen Innes Department of Mechanical Engineering University of Auckland New Zealand
G. B. Delkumburewatte Senior Lecturer Head/Department of Textile and Apparel Technology Open University of Sri Lanka P.O. Box 21 Nawala Nugegda Sri Lanka E-mail:
[email protected]
E-mail: m
[email protected] d.bhattacharyya@auckland. ac.nz
© Woodhead Publishing Limited, 2011
Woodhead Publishing Series in Textiles
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Watson’s textile design and colour, Seventh edition Edited by Z. Grosicki Watson’s advanced textile design Edited by Z. Grosicki Weaving, Second edition P. R. Lord and M. H. Mohamed Handbook of textile fibres, Volume 1: Natural fibres J. Gordon Cook Handbook of textile fibres, Volume 2: Man-made fibres J. Gordon Cook Recycling textile and plastic waste Edited by A. R. Horrocks New fibers, Second edition T. Hongu and G. O. Phillips Atlas of fibre fracture and damage to textiles, Second edition J. W. S. Hearle, B. Lomas and W. D. Cooke Ecotextile ’98 Edited by A. R. Horrocks Physical testing of textiles B. P. Saville Geometric symmetry in patterns and tilings C. E. Horne Handbook of technical textiles Edited by A. R. Horrocks and S. C. Anand Textiles in automotive engineering W. Fung and J. M. Hardcastle Handbook of textile design J. Wilson High-performance fibres Edited by J. W. S. Hearle Knitting technology, Third edition D. J. Spencer Medical textiles Edited by S. C. Anand xiii © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
xiv 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39
Woodhead Publishing Series in Textiles
Regenerated cellulose fibres Edited by C. Woodings Silk, mohair, cashmere and other luxury fibres Edited by R. R. Franck Smart fibres, fabrics and clothing Edited by X. M. Tao Yarn texturing technology J. W. S. Hearle, L. Hollick and D. K. Wilson Encyclopedia of textile finishing H.-K. Rouette Coated and laminated textiles W. Fung Fancy yarns R. H. Gong and R. M. Wright Wool: Science and technology Edited by W. S. Simpson and G. Crawshaw Dictionary of textile finishing H.-K. Rouette Environmental impact of textiles K. Slater Handbook of yarn production P. R. Lord Textile processing with enzymes Edited by A. Cavaco-Paulo and G. Gübitz The China and Hong Kong denim industry Y. Li, L. Yao and K. W. Yeung The World Trade Organization and international denim trading Y. Li, Y. Shen, L. Yao and E. Newton Chemical finishing of textiles W. D. Schindler and P. J. Hauser Clothing appearance and fit J. Fan, W. Yu and L. Hunter Handbook of fibre rope technology H. A. McKenna, J. W. S. Hearle and N. O’Hear Structure and mechanics of woven fabrics J. Hu Synthetic fibres: Nylon, polyester, acrylic, polyolefin Edited by J. E. McIntyre Woollen and worsted woven fabric design E. G. Gilligan Analytical electrochemistry in textiles P. Westbroek, G. Priniotakis and P. Kiekens Bast and other plant fibres R. R. Franck
© Woodhead Publishing Limited, 2011
40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61
Woodhead Publishing Series in Textiles
xv
Chemical testing of textiles Edited by Q. Fan Design and manufacture of textile composites Edited by A. C. Long Effect of mechanical and physical properties on fabric hand Edited by Hassan M. Behery New millennium fibers T. Hongu, M. Takigami and G. O. Phillips Textiles for protection Edited by R. A. Scott Textiles in sport Edited by R. Shishoo Wearable electronics and photonics Edited by X. M. Tao Biodegradable and sustainable fibres Edited by R. S. Blackburn Medical textiles and biomaterials for healthcare Edited by S. C. Anand, M. Miraftab, S. Rajendran and J. F. Kennedy Total colour management in textiles Edited by J. Xin Recycling in textiles Edited by Y. Wang Clothing biosensory engineering Y. Li and A. S. W. Wong Biomechanical engineering of textiles and clothing Edited by Y. Li and D. X-Q. Dai Digital printing of textiles Edited by H. Ujiie Intelligent textiles and clothing Edited by H. Mattila Innovation and technology of women’s intimate apparel W. Yu, J. Fan, S. C. Harlock and S. P. Ng Thermal and moisture transport in fibrous materials Edited by N. Pan and P. Gibson Geosynthetics in civil engineering Edited by R. W. Sarsby Handbook of nonwovens Edited by S. Russell Cotton: Science and technology Edited by S. Gordon and Y.-L. Hsieh Ecotextiles Edited by M. Miraftab and A. R. Horrocks Composite forming technologies Edited by A. C. Long
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
xvi 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
Woodhead Publishing Series in Textiles
62 Plasma technology for textiles Edited by R. Shishoo 63 Smart textiles for medicine and healthcare Edited by L. Van Langenhove 64 Sizing in clothing Edited by S. Ashdown 65 Shape memory polymers and textiles J. Hu 66 Environmental aspects of textile dyeing Edited by R. Christie 67 Nanofibers and nanotechnology in textiles Edited by P. Brown and K. Stevens 68 Physical properties of textile fibres, Fourth edition W. E. Morton and J. W. S. Hearle 69 Advances in apparel production Edited by C. Fairhurst 70 Advances in fire retardant materials Edited by A. R. Horrocks and D. Price 71 Polyesters and polyamides Edited by B. L. Deopura, R. Alagirusamy, M. Joshi and B. S. Gupta 72 Advances in wool technology Edited by N. A. G. Johnson and I. Russell 73 Military textiles Edited by E. Wilusz 74 3D fibrous assemblies: Properties, applications and modelling of three-dimensional textile structures J. Hu 75 Medical and healthcare textiles Edited by S. C. Anand, J. F. Kennedy, M. Miraftab and S. Rajendran 76 Fabric testing Edited by J. Hu 77 Biologically inspired textiles Edited by A. Abbott and M. Ellison 78 Friction in textile materials Edited by B. S. Gupta 79 Textile advances in the automotive industry Edited by R. Shishoo 80 Structure and mechanics of textile fibre assemblies Edited by P. Schwartz 81 Engineering textiles: Integrating the design and manufacture of textile products Edited by Y. E. El-Mogahzy 82 Polyolefin fibres: Industrial and medical applications Edited by S. C. O. Ugbolue © Woodhead Publishing Limited, 2011
Woodhead Publishing Series in Textiles
83 Smart clothes and wearable technology Edited by J. McCann and D. Bryson 84 Identification of textile fibres Edited by M. Houck 85 Advanced textiles for wound care Edited by S. Rajendran 86 Fatigue failure of textile fibres Edited by M. Miraftab 87 Advances in carpet technology Edited by K. Goswami 88 Handbook of textile fibre structure, Volume 1 and Volume 2 Edited by S. J. Eichhorn, J. W. S. Hearle, M. Jaffe and T. Kikutani 89 Advances in knitting technology Edited by K. F. Au 90 Smart textile coatings and laminates Edited by W. C. Smith 91 Handbook of tensile properties of textile and technical fibres Edited by A. R. Bunsell 92 Interior textiles: Design and developments Edited by T. Rowe 93 Textiles for cold weather apparel Edited by J. T. Williams 94 Modelling and predicting textile behaviour Edited by X. Chen 95 Textiles, polymers and composites for buildings Edited by G. Pohl 96 Engineering apparel fabrics and garments J. Fan and L. Hunter 97 Surface modification of textiles Edited by Q. Wei 98 Sustainable textiles Edited by R. S. Blackburn 99 Advances in yarn spinning technology Edited by C. A. Lawrence 100 Handbook of medical textiles Edited by V. T. Bartels 101 Technical textile yarns Edited by R. Alagirusamy and A. Das 102 Applications of nonwovens in technical textiles Edited by R. A. Chapman 103 Colour measurement: Principles, advances and industrial applications Edited by M. L. Gulrajani 104 Textiles for civil engineering Edited by R. Fangueiro © Woodhead Publishing Limited, 2011
xvii 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
xviii 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
Woodhead Publishing Series in Textiles
105 New product development in textiles Edited by B. Mills 106 Improving comfort in clothing Edited by G. Song 107 Advances in textile biotechnology Edited by V. A. Nierstrasz and A. Cavaco-Paulo 108 Textiles for hygiene Edited by B. McCarthy 109 Nanofunctional textiles Edited by Y. Li 110 Joining textiles Edited by I. Jones and G. Stylios 111 Soft computing in textiles Edited by A. Majumdar 112 Textile design Edited by A. Briggs-Goode and K. Townsend 113 Biotextiles as medical implants Edited by M. King and B. Gupta 114 Textile thermal bioengineering Edited by Y. Li 115 Woven textile structure B. K. Behera and P. K. Hari 116 Handbook of textile and industrial dyeing. Volume 1: Principles processes and types of dyes Edited by M. Clark 117 Handbook of textile and industrial dyeing. Volume 2: Applications of dyes Edited by M. Clark 118 Handbook of natural fibres, Volume 1: Types, properties and factors affecting breeding and cultivation Edited by R. Kozlowski 119 Handbook of natural fibres, Volume 2: Processing and applications Edited by R. Kozlowski 120 Functional textiles for improved performance, protection and health Edited by N. Pan and G. Sun 121 Computer technology for textiles and apparel Edited by Jinlian Hu 122 Advances in military textiles and personal equipment Edited by E. Sparks 123 Specialist yarn, woven and fabric structure: Developments and applications Edited by R. H. Gong 124 Handbook of sustainable textile production M. Tobler © Woodhead Publishing Limited, 2011
2 The physical properties of weft knitted structures B. COOKE, Formerly Senior Lecturer in Knit Design (UMIST), University of Manchester, UK Abstract: Modern knitted fabrics cover a wide range of structures; therefore this chapter is confined to a generalised summary of weft knitted fabrics. It explains why knitted fabrics stretch more easily than woven fabrics made from similar materials and compares the dimensional ability, creasing and properties of both fabrics. Key words: knitted fabrics, weft, woven, yarn, creasing, properties.
2.1
Introduction
Modern knitted fabrics range from gossamer thin veil-like structures knitted on ultra-fine gauge circular weft knitting machines to immensely strong rigid multi-layer multi-axial structures produced on Raschel warp knitting machines, and include every conceivable combination of properties in between these two extremes. For this reason any attempt to discuss or characterise the physical properties of knitted structures within the confines of a single chapter must be limited to a generalised summary of the commercially significant weft knitted fabrics. A further complication that arises in such a discussion is the extent to which the yarn properties influence the properties and performance of the yarn/structure combination. For example if a comparison is made between a simple plain-weft knitted structure (single jersey) knitted from textured polyester and the same structure knitted on the same machine from PTFE coated stainless steel, then the polyester fabric will be soft, warm and stretchy and the stainless steel fabric will be hard, cold and unyielding and with relatively little stretch – the same knitted structure producing totally different fabrics with radically different properties. For this reason the discussion will be limited to fabrics produced with conventional textile yarns. On a historical timescale knitting is a relatively modern technique. Weaving was developed around 7000 BC in the Middle East, whereas weft knitting was most probably developed in Coptic Egypt in the third to fourth century AD, more than 7000 years later. The early uses of knitted fabrics are not known, but by the ninth century AD weft knitted stockings were in use in the Arab world and by the tenth century two-colour jacquard patterned stockings were relatively common in Egypt. Knitting spread from North Africa to Spain following the Arab conquest of the southern regions and by the twelfth century had spread into northern Spain 37 © Woodhead Publishing Limited, 2011
38
Advances in knitting technology
and southern France. The manufacture of knitted products then disseminated north and east through Europe reaching Italy in the 14th century, Britain in the 15th century and Scandinavia in the 16th and 17th centuries. By the time of Elizabeth I of England, knitted products were well established in three main product categories: stockings, gloves and hats; and their success in these markets was due to their physical properties, which could not be replicated by weaving. For each of these products stretch, warmth, softness and conformability were desirable; properties inherent in knitted wool. In contrast warm woven fabrics were thick, hard, stiff and unyielding with very little stretch. During the following three centuries knitted products substantially retained the same markets, only expanding into outerwear in the nineteenth century with the development of jerseys and guernseys and into household textiles with the development of warp knitting and the manufacture of lace and blankets.
2.2
Stretch and recovery properties
In order to understand why knitted fabrics stretch so much more easily than woven fabrics made from similar materials it is necessary to study their basic structure. In simple woven structures the yarns pass through the fabric in an undulating fashion diverting above and below the yarns in the other system (see Plate I between pages 46 and 47). This undulation is called crimp (warp or weft crimp). Consequently when a stress force is applied across the fabric there is only scope for relatively little extension, in the region of 3–5%, before the crimp is removed and the yarns straighten. At this point a much greater force is required to stretch the yarns, usually more than a wearer is able to tolerate, and further stretch beyond this point becomes uncomfortable. In contrast to woven fabrics where the accessible extension is usually less than 10%, knitted fabrics are often able to develop very high extensions, as high as 100%, through totally different deformation mechanisms. The diagram of a model of the simplest plain fabric shows the fabric to be constructed of linear arrays of needle loops linked together horizontally by sinker loops and vertically by interlinking (see Plate II between pages 46 and 47). Horizontal stretch is achieved in the first instance by changes in curvature (flattening) of the base of the sinker loops and the top of the needle loops. This is typically a low modulus deformation. As extension proceeds and the curved yarn segments straighten, sufficient stress eventually develops to exceed the inter-yarn frictional forces at the cross-over points or binding areas (see Plate III between pages 46 and 47) and yarn interchange takes place moving yarn segments from the vertical sides of the loops into the tops and bottoms of the loops. In this way a plain-knit fabric may stretch by 15–20% in the width without any significant yarn extension taking place. In a similar manner extension in the length axis occurs initially by a straightening of the sides of the loops. Then as yarn stress levels rise yarn interchange moves yarn segments from the bottoms of the sinker
© Woodhead Publishing Limited, 2011
The physical properties of weft knitted structures
39
loops and tops of the needle loops into the vertical sides of the loops, and the loops lengthen. Axial stretch is normally lower than width-wise stretch, typically 5–10%. When the knitted loops are interlinked into rib structures such as 1 × 1 rib, then a further stretch mechanism comes into play (see Plate IV between pages 46 and 47). In order to explain this mechanism it is helpful to examine the top view of a section taken across the wales. This figure shows that the face and reverse loops are joined by inter-stitches that link the face and reverse in a ‘concertina’-like manner. As a result of the bending and torsional forces in the inter-stitches, rib fabrics contract once they leave the needles with the result that the wale density becomes much higher than the needle density on the knitting machine. Typically 1 × 1 rib structures may contract by as much as 50% of their knitted width. When lateral forces are then applied to the retracted structure it is able to extend to its original knitted width before the mechanisms described above come into play. This ‘concertina’ deformation provides very low modulus extension and for this reason rib structures are used at the cuffs, neck and waist of garments where high stretch is essential for ease of fit. Normally 1 × 1 rib and 2 × 2 rib structures provide the greatest stretch and therefore are most frequently used in this way. Whenever horizontal linear yarn elements are incorporated into the structure, for example inlay or floats such as those in jacquard fabrics, then the width stretch is greatly reduced.
2.3
Recovery properties
Once a knitted structure has been stretched in use, for example when the neck of a sweater has been stretched over the wearer’s head, it is desirable for the appearance of the garment that the fabric should contract or recover to its original dimension. The deformation described above that involves a flattening of the curvature of the yarn loops usually recovers quickly and can be considered to be largely elastic. However, the second stage of deformation involving yarn movement against frictional resistance tends to act like a ‘ratchet mechanism’, and is not recovered immediately and may not recover at all without ‘outside’ help, leading to hysteresis in the stress–strain cycle. This fraction of the original extension can be considered as a ‘set’ and can cause a garment to become ‘baggy’. This explains why rib fabrics are so much better than plain fabrics when used for cuffs, necks and waists because they can provide the necessary stretch without the yarn forces rising to a level where yarn interchange against friction takes place. The process of recovery in weft knitted fabric is complicated by the mechanism of relaxation shrinkage and this will be discussed under dimensional stability below. If an even greater level of stretch is desired, for example the top rib of socks, then the ‘concertina’ contraction may be enhanced by incorporating an elastomeric yarn element under tension into the structure in such a way that once the fabric leaves the needles the stress in the elastomer forces the fabric to contract much
© Woodhead Publishing Limited, 2011
40
Advances in knitting technology
more than normal. The elastomer is typically introduced as an ‘inlay’ element. When the elastomer is incorporated as a purely horizontal element, the main effect is to enhance the width-wise stretch. If the elastomer is incorporated under tension into the loop structure it will cause the fabric to contract in both the width and axial directions and thus enhance the stretch in both directions. A further advantage of using elastomer in knitted fabrics is the improvement in recovery following extension that such elements provide.
2.4
Dimensional stability
Fabrics are considered to have good dimensional stability if they resist permanent deformation during use and during washing and dry-cleaning. When compared with woven structures, most simple knitted fabrics cannot be considered to have good dimensional stability. First they do not recover well from stretching due to the ‘ratchet mechanism’ described above. Second, they are subject to a process known as relaxation shrinkage which commences as soon as the fabric/garment is removed from the knitting machine and does not cease until the product has been washed or dry-cleaned several times. Third, if they are made from untreated animal fibres such as wool or alpaca they may also be liable to felting shrinkage. Relaxation shrinkage leads to progressive changes in the width and axial dimensions of the textile, which usually results in reductions in both dimensions. However, this is not always the case, and fabric that has been excessively stretched in length during finishing and has not been effectively stabilised by heat-setting or consolidation may increase in width during wash and wear. This problem is frequently encountered with cotton T-shirts. Relaxation shrinkage occurs due to two different mechanisms. The majority of common textile polymers are non-Newtonian in their response to stress. That is to say they have a non-linear stress–strain curve and they ‘creep’ (extend) with time under constant load. When the force is removed the creep deformation is not immediately recovered and this deformation then gradually reduces over time. On the way into the knitted fabric the yarn is subjected to quite high tensions and a proportion of the deformation (stretch) that occurs is retained in the yarn after knitting as creep deformation. With time this deformation reduces and the yarn becomes shorter with the consequence that the knitted loops become smaller and the fabric will shrink in the width and length. In the case of hydrophilic polymers immersion in water will accelerate this recovery and steaming will remove some of the creep deformation for both hydrophilic and hydrophobic polymers. The second cause of relaxation shrinkage is the mechanism described above that enables knitted fabric to stretch easily. During most knitting processes the fabric is subject to take-down tension and the needles are generally spaced further apart than the loops will lie in the finished fabric. As a consequence the fabric is stretched in both the width and length and a proportion of the stretch will be in the form of
© Woodhead Publishing Limited, 2011
The physical properties of weft knitted structures
41
the ratchet type deformation that will not recover immediately once the fabric/ garment is removed from the machine. This residual deformation will be stored in the fabric in addition to the yarn creep deformation and together they have the potential to cause quite considerable dimensional changes in the form of relaxation shrinkage as the product moves along the supply chain towards the user, and even after purchase during the first few cycles of use. Unfortunately a third cause of dimensional change can also occur with hydrophilic fibres such as cotton and wool and that is conventional shrinkage caused by contact with water. When yarns are not pre-shrunk they have the potential to reduce in length on wetting and this latent shrinkage is in addition to the two forms of relaxation shrinkage described above. As a consequence of these causes of shrinkage, knitted products often have a reputation for poor dimensional stability. Fortunately solutions do exist. Thermoplastic fabrics can be heat-set to stable dimensions and hydrophilic fabrics can be finished through tension-free processes or through consolidation machinery that forces them to a stable configuration. The main difficulties now arise with garments produced from dyed yarns that are not subjected to wet finishing or tumble drying and thus retain their potential for relaxation shrinkage. Since the advent of Superwash wool and other shrink resistant wool yarns the problem of felting shrinkage has been largely eliminated. However, untreated animal fibres will felt if treated in hot/wet conditions with agitation. The effect of felting is to cause the yarn to retract and thicken and as a consequence the fabric will reduce in width and length and increase in thickness. Tumble drying a wet garment often precipitates felting and can lead to severe irreversible shrinkage.
2.5
Creasing
Most flexible laminar materials are subject to creasing. Creasing occurs when the sheet of material is folded or bent, and the sharper the fold and the longer it is maintained the more permanent the crease will become. Materials such as paper, which are easily deformed into very sharp folds, are subject to serious permanent crease damage. When normal writing or printing paper is folded the crease easily becomes so sharp that it becomes a permanent feature and indeed creasing can be used to convert paper into three-dimensional forms. This permanent creasing is exploited in the Japanese art form origami. The mechanism of creasing is interesting because it involves both time-dependent deformation (creep) as well as compressive yield. Paper and most textiles are made from fibres containing linear polymers. When these fibres are bent into a sharp radius of curvature the molecules in the outer half of the bend suffer extension and if this bend is maintained over time they develop creep deformation. Conversely the molecules on the inner half of the bend are subjected to compressive forces, and as the compressive yield stress is so much lower than the extensive yield stress for any given polymer they can easily suffer compressive yield that is an irreversible failure (collapse) of the molecular structure. In other words the crease becomes permanent.
© Woodhead Publishing Limited, 2011
42
Advances in knitting technology
In textile materials the extent to which this mechanism will occur depends on the type of polymeric material and the radii of curvature that develop in the fibres as the fabric is folded. In general terms creasing is most severe in thin fabrics where the fibres are rigidly held in place, for example in thin tightly woven cotton poplins, where they are constrained to bend to tight radii during creasing. Knitted fabrics are by their nature less susceptible to creasing than woven fabrics. Generally knitted fabrics are thicker than woven fabrics (see section on fabric thickness below) and the yarns are more mobile in the fabric structure than the yarns in woven fabrics. In addition, knitting yarns are twisted to lower twist factors than weaving yarns and the fibres are less tightly held in the yarn structure. Thick fabrics bend to lower radii of curvature than thin fabrics and the more mobile yarn and fibre arrangement means that yarns can roll or bend in such a way that their bending radii are reduced and permanent deformation is avoided. For all these reasons a knitted fabric will crease less than woven fabric of a similar area density and the creases that do form are more easily removed. It should be noted that wet or steam ironing will remove the appearance of creases from the majority of fabrics both knitted and woven. However, once the fibres in a particular section of yarn have suffered compressive yield they are permanently weakened and creases are much more likely to occur in exactly the same places. This process is particularly evident with cotton denim jeans. Creases develop at the tops of the legs where the legs meet the pelvis and behind the knees and although they appear to vanish after washing and ironing they reappear as soon as they are worn again. The effect is highlighted by the fact that the denim loses colour along the crease line and the permanent creases show as pale lines against the dark blue background.
2.6
Thickness and compression properties
Fabric thickness is an extremely important parameter for a variety of reasons. Fabric thickness is an important variable in determining fabric stiffness and hence the extent to which the fabric will drape and conform. Fabric thickness is the most important variable determining the rate of heat transfer and hence the so-called ‘warmth’ of the fabric. Fabric thickness affects air permeability and moisture absorbency and also has a great influence on the abrasion resistance. For the majority of simple woven fabrics, plain weave, twills and satins, the fabric thickness is very close to the sum of the yarn diameters in the warp and weft. This is because the crimp curvature is small and is offset by the yarn compression that occurs between the warp and weft yarns under the warp and weft crowns. In contrast, when a cross-section through a plain knit is examined, it is apparent that yarn curvature out of the plane of the fabric contributes to the effective fabric thickness such that the thickness is greater than twice the yarn diameter. When rib and double jersey fabric sections are studied, yarn curvature is again present together with the inter-stitch that joins the face and reverse loops,
© Woodhead Publishing Limited, 2011
The physical properties of weft knitted structures
43
and in this case the fabric thickness is significantly greater than four times the yarn diameter. Although it is difficult to compare knitted and woven fabrics on a like-for-like basis because they still tend to occupy different market niches, it is generally a fact that knitting yarns have a much higher diameter than weaving yarns and this together with the factors discussed above means that knitted fabrics are usually much thicker than woven fabrics although exceptions can always be found to such generalisations. If comparable woven and knitted fabrics are compared in terms of their compression properties, knitted fabrics are found to be much more easily compressed than woven fabrics. Weaving yarns are almost always more highly twisted than knitting yarns and are therefore harder and less easily compressed. Most of the fabric thickness is occupied by two yarn diameters one on top of the other and the application of a compressive force almost immediately results in yarn compression. In other words the compressive modulus of the fabric is almost immediately equal to the compressive modulus of the yarns, which themselves are hard twisted. A crosssection through a plain knitted fabric shows that only approximately two-thirds of the fabric thickness is occupied by the two yarn diameters. The resistance to compression is therefore initially due to bending forces in the loop segments rather than the direct compression of the yarns, and when the yarn segments are flattened such that the yarns themselves start to compress the softer more open yarn structure results in a much lower compression modulus. In short, knitted fabrics are much softer and more easily compressed than comparable woven fabrics.
2.7
Air permeability
The diagrams shown in the colour section in the discussions of stretch, thickness and compression do not provide much help in assessing the comparative air permeability of woven and knitted fabrics. Air permeability is linked to fabric coverfactor, and photographic images give a much better impression of cover-factor than diagrams. Cover-factor is defined as the ratio of the area covered by the yarn to the area covered by the fabric. A fabric with zero permeability would therefore have a cover factor of 1. The photographs show that the single jersey fabric has a much lower cover factor than a comparable plain weave and therefore the air permeability would be much higher. Because each knitted loop in effect encloses a ‘hole’ in the fabric the air permeability of knitted fabrics is generally much higher than that of woven fabrics and knitted fabrics are not used where wind resistance is required unless they are coated with an airflow resistant coating such as polyurethane.
2.8
Thermal properties
As the majority of textile fibres have very similar coefficients of thermal conductivity, two main structural factors determine the thermal conductivity of
© Woodhead Publishing Limited, 2011
44
Advances in knitting technology
fabrics; the thickness, and the extent to which the structure traps stationary air. Knitted fabrics are naturally much thicker than equivalent woven fabrics (see the section on fabric thickness above), and as discussed above the knitted loop encloses a cell or ‘hole’ in the fabric structure that is capable of trapping air under the right conditions. Double knits and ribs have two layers of offset loops and therefore two layers of offset holes. The combination of high thickness and a high volume of trapped air leads to fabrics with low thermal conductivity provided they are protected from wind pressure by windproof outer layers or shell fabrics. The thermal insulation of knitted fabrics can be improved further by using techniques such as plush knitting with micro-fibre yarns. This technique increases the fabric thickness, and subsequent raising and cropping produces fleece fabrics that have outstanding thermal insulation properties together with a higher resistance to ‘wind chill’ than conventional knits, and they have replaced conventional sweaters in the performance sportswear market.
2.9
Liquid transfer properties
Liquid transfer through textiles is usually a two-stage process. Firstly the liquid wets the surface of the fabric and is absorbed into the yarn by capillary attraction and also into the fibre structure in the case of hydrophilic polymers. Secondly the liquid moves through the structure by a combination of diffusion and capillarydriven wicking. In the case of fabrics produced from hydrophilic fibres such as cotton or wool the initial wetting enables liquid molecules to access the surface of the fibres and they then effectively move ‘into solution’ into the polymer structure until the polymer becomes saturated. Liquid then enters the capillary spaces between the fibres and moves or wicks along the yarn structure away from the liquid reservoir. The distance travelled depends on the contact angle between the liquid and the polymer, and the physical dimensions of the capillary spaces. The liquid that enters into solution within the fibres is effectively trapped and prevented from moving away from the source. Naturally hydrophobic polymers prevent liquid solution entering into the fibre and thus prevent the trapping of moisture. With time the liquid that has travelled along the yarn capillaries will evaporate and then diffuse into the air spaces in the fabric. If there is an air pressure gradient across the fabric the liquid molecules in the air spaces will be moved through and out of the fabric. The more permeable the fabric the higher the air flow will be for a given pressure gradient and therefore the greater the rate of liquid transfer. When a comparison is made between woven and knitted fabrics made from the same polymer/fibre/yarn combination then the capillary attraction and wicking and the solution of the liquid into the polymer will naturally be similar. The main difference will be in the air flow through the fabric, and the knitted fabric will be more permeable and hence the rate of liquid transfer will be greater.
© Woodhead Publishing Limited, 2011
The physical properties of weft knitted structures
45
2.10 Comfort Fabric comfort is an extremely complex issue depending as it does on a large number of variables. For example, a fabric that is comfortable in a cool dry environment may be unpleasant to wear in a hot humid climate. In order to have a meaningful discussion it is necessary to specify the following: • environmental conditions including temperature, humidity, wind speed and precipitation; • the activity level of the wearer; • the function of the garment, for example underwear, outerwear, shell, lining, etc.; • the fit of the garment. The perception of comfort takes place through a number of different physiological interactions between the textile and the wearer: • The mechanical interaction between the skin surface and the fibres and yarns. This includes roughness or smoothness as well as pressure, shear and abrasion. • The moisture balance as the wearer sweats or as rain wets the outer layer. • The temperature balance as the body generates heat through exercise or as heat penetrates to the skin surface from the outside. Against this complex background knitted fabrics offer advantages in three main areas. Firstly the stretch properties of knitted fabrics offer better conformability and prevent excess pressure and/or shear developing between the garment and the body surface. This is particularly important for underwear as well as for active sportswear and swimwear to the extent that the overwhelming majority of these goods are made from knitted fabric. Secondly, as already discussed above, knitted fabrics offer considerable advantages over woven fabrics in terms of insulation especially when they are protected from the wind. Thirdly, knitted fabrics perform well when there is a need to transport sweat away from the skin surface. This property enhances the advantage of natural stretch in active sports applications. Conversely knitted fabrics do not provide good protection from wind chill and must be used under a woven shell fabric in such conditions. Similarly they are difficult to waterproof effectively.
2.11 Pilling and abrasion Pilling occurs when repetitive rubbing causes the surface fibres to become entangled and this entanglement is shown as a ball of fibres being drawn out of the yarn structure. The fibre length that is drawn out then rolls into a pill or ball, and the draw-out roll-up process continues and the pill increases in diameter.
© Woodhead Publishing Limited, 2011
46
Advances in knitting technology
Large numerous pills are unsightly and ruin the appearance of the garment. The key to controlling pilling is the use of spinning and fabric manufacture techniques that prevent fibres being drawn out of the yarn structure and/or the use of fibres that fatigue easily so that the pills that form break off. Fibres are held tightly within the yarn structure when the lateral forces are high due to high twist levels or due to high inter-yarn forces within the fabric. Natural fibres such as cotton or wool tend to fatigue rapidly and allow the pills to break off. Unfortunately the trends in the Industry during the last forty years have led to the production of fabrics that pill extensively. In the search for softer and more comfortable products the twist levels have been progressively reduced. Similarly both woven and knitted fabrics have been made looser. Finally there has been a progressive increase in the use of synthetic fibres such as nylon, acrylic and polyester that do not fatigue quickly and develop into pills that do not break off. All these developments impinge more markedly on knitted fabrics because the inter-loop compressive forces are lower than the warp/weft forces in woven fabrics. The result is that many knitted garments sold by well-known high street retailers pill very badly and lose their smart appearance within only a few days of use. The solution to the problem is simple: increase the twist and knit tighter, but this would lead to the fabric becoming harsher and more expensive.
2.12 Knitted fabrics with special properties For the reasons given in the introduction this description of the properties of knitted fabrics has focused on the most common weft knitted structures manufactured from normal textile fibres and used in apparel end-uses. During the last thirty years the introduction of high-performance yarns such as Kevlar, Nomex and Lycra, the development of industrial products on v-bed machines and the very rapid diversification of the warp knitting machinery sector have led to the production and market acceptance of knitted products with properties that are radically different from those described above. By incorporating elastomers such as Lycra, warp knitted fabrics can stretch by as much as 300% with good recovery properties. By using modified stainless steel yarns weft knitted gloves can be produced that are resistant to band saw damage. The use of Nomex with wool enables weft knits to be produced that are resistant to the very high temperature gasoline fires that occur in motor racing. Polyester microfibre yarns are warp knitted into prosthetic arterial implants. The list of special high performance knitted products is growing by the week and in most cases their properties are different from those described above. However, a thorough knowledge of fabric structure together with an understanding of the physics and mechanics of polymers and yarns enables these special fabrics to be designed and developed in a rational systematic way.
© Woodhead Publishing Limited, 2011
The physical properties of weft knitted structures
47
2.13 Sources of further information and advice Each of the topics covered above is of sufficient complexity to deserve a separate publication and the books listed below expand and advance the discussions summarised in this chapter. Thermal and Moisture Transport in Fibrous Materials, N. Pan and P. Gibson. Woodhead Publishing Series in Textiles No. 56. Wetting and Wicking in Fibrous Materials, A. Patnaik, A. Gosh, R. S. Rengasamy and V. K. Kothari. Textile Progress, 38 (1), Woodhead Publishing. Pilling, J. O. Ukponmwan, A. Mukhopadhyay, K. N. Chatterjee. Textile Progress 28 (3), Woodhead Publishing. Textiles for Protection, R. A. Scott. Woodhead Publishing Series in Textiles No. 44. Textiles in Sport, R. Shishoo. Woodhead Publishing Series in Textiles No. 45. Textiles for Cold Weather Apparel, J. Williams. Woodhead Publishing Series in Textiles No. 93. Biomechanical Engineering of Textiles and Clothing, Y. Li and D. X.-Q. Dai. Woodhead Publishing Series in Textiles No. 52. Smart Textiles for Medicine and Healthcare, L. Van Langenhoven. Woodhead Publishing Series in Textiles No. 63.
© Woodhead Publishing Limited, 2011
Plate I
Plate II
© Woodhead Publishing Limited, 2011
Plate III
Plate IV
© Woodhead Publishing Limited, 2011
3
1 2 3 4 5 6 7 8 9
Modelling of knitting R. B. RAMGULAM, Albany international, bury, UK Abstract: This chapter discusses the various aspects of mathematical modelling of knitted fabrics, with the emphasis on tensile behaviour. Key words: geometry, energy, pressure, loop, deformation.
3.1
Introduction
Various aspects of mathematical modelling of knitted fabrics are discussed in this chapter. The purely geometrical models of knitted fabrics are very useful to the knitter not only conceptually but in practical terms as well, as they allow decisions on parameters such as stitch length to achieve the required fabric dimensions. Mechanical models of tensile behaviour occupy most of this chapter. Elastica theory is at the core of the force-equilibrium models. An extended summary of an energy method, for which the 3D loop is very appropriate, is described in detail. Knitted garments, on account of their ability to fit closely to the body of the wearer, are naturally suitable as garments for medical purposes. Knowledge of the pressure exerted on the body by the garment is then important. A model that predicts the pressure profile based on membrane mechanics is included in this chapter. Finally a model on heat and moisture transmission in textiles in general is described on account of its importance to comfort.
3.2
3 4 5 6 7 8 9 40 1 2 43X
Knitted fabric geometry
The basic principles underlying the geometry of knitted fabrics were laid by Doyle1 and extended by Munden.2 Doyle found that in the case of the dry relaxed plain knit structure, the stitch density is a function primarily of the length of yarn in a loop and is independent of the yarn material, yarn structure and the system used to form the stitches. The foundation of the work is that knitted fabrics, given the opportunity, will take up a stable relaxed configuration guided by the principle of minimum energy. The dimensions of plain-knitted fabrics in such a state, first described numerically by Munden,2 are dependent on the length of yarn knitted into each loop. Munden’s model is based on an assumption by Leaf and Glaskin3 that any homogeneous strip of material bent into a loop will always take up the same configuration, independent of its physical properties. Munden was then able to show that the dimensions of plain-knitted fabrics are uniquely determined by the 48 © Woodhead Publishing Limited, 2011
Modelling of knitting
49
length of yarn knitted into each loop. For this to apply, the fabric has to be in its fully-relaxed state, i.e. a configuration of minimum energy. Consider Fig. 3.1 below. The two loops AB and A1B1 are similar in that if the distance of an arbitrary point P from the origin is r then the distance of the corresponding point P1 from the origin is r1 = p * r, where p is a constant. If the loops are described in terms of polar coordinates then the length of loop segment AC is given by: [3.1] and r1 = p * r,
Since Therefore:
Hence the loop length of A1B1 is p * loop length of AB.
3.1 Two similar loops.
© Woodhead Publishing Limited, 2011
[3.2]
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
50 1 2 3 4 5 6 7 8
Advances in knitting technology
Further we have
But OBx and OB1x are half the wale
spacing of the small and large loop respectively. Hence:
The course spacing, Fig. 3.2, is given by the length Aa. Minimum bending energy consideration suggests that the crossover of loops for a stable configuration occurs when the vertical coordinate of D, which is the narrowest point of loop ACDB, coincides with the vertical coordinate of c, the widest point of loop acdb. Since the two loops are identical in shape and size we have: AL = aN ⇒ Aa = LN. Hence the course spacing is given by the length LN, which is the difference of the vertical coordinates of the widest and narrowest points of the loop. The course spacing is therefore a parameter dependent on the loop shape structure only. Therefore the course spacing for loop A1B1 in Fig. 3.1 is p * Aa. The above analysis shows that course and wale spacing depend on the loop structure only. Hence:
3 4 5 6 7 8 9 40 1 2 43X
.
3.2 Course spacing.
© Woodhead Publishing Limited, 2011
[3.3]
Modelling of knitting
51 [3.4]
[3.5]
[3.6] From these simple equations the weight and dimensions of the fabrics are derived as follows: [3.7]
[3.8]
3.2.1 Cover factor The space in the plane of the fabric occupied by the yarn forming the loop is given by L * d, where L is the length of yarn in the loop and d is the yarn diameter. The area occupied by a single loop is
. It has been shown by Doyle1 for
non-relaxed fabrics and Munden2 for relaxed fabrics that the stitch density is, for plain-knitted fabric, proportional to the loop is
. Therefore the fractional area occupied by .
This relationship ignores the bending of yarn at a right angle to the plane of the fabric and the crossover areas of loops. For practical purposes, given that the yarn the cover factor dimension is expressed in terms of linear density and can be conveniently defined as
. The cover factor affects properties such as
collapse from stretch yarns, pilling and change in fabric area by drying.
3.3
Mechanics of knitted fabric: 2D model
In this section the mechanism of deformation of plain knitted fabric is described, assuming yarns behave like thin elastic rods or elasticas. First the structure of a knitted loop, the unit of the fabric, is explained. The mechanics of thin extensible filaments subject to large deformations is developed followed by a mechanical model of fabric behaviour subjected to external forces. The model is based partly © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
52 1 2 3 4 5 6 7 8 9
Advances in knitting technology
on the work of Shanahan and Postle4,5 whilst the computational aspects borrow from the approach of Konopasek and Hearle6 as regards elasticas. The following list gives the variables and their meanings for the 2D mechanical model. Table 3.1 Nomenclature Variable Description x, y, z v, w s so ε wx wy M Fv Fw p Ub E E b A d β
Global coordinates. Local coordinates. Arc length measured along centreline of deformed elastica/yarn. Arc length measured along centreline of undeformed elastica/yarn. Strain. Direction cosine of local coordinate, w, with respect to the x-axis. Direction cosine of local coordinate, w, with respect to the y-axis. Moment on small element of elastica/yarn. Internal force component, perpendicular to centreline of elastica/yarn. Internal force component, tangential to centreline of elastica/yarn. Curvature of centreline of elastica/yarn. Bending energy. Tensile modulus of elastica/yarn. Bending modulus of elastica/yarn. Cross-section area of elastica/yarn. Thickness of elastica/yarn. Interlocking angle.
3.3.1 Structure of the knitted loop
4 5 6 7 8 9 40 1 2 43X
A loop has mirror symmetry about the vertical line going through points D in Fig. 3.3. Further consideration of half the loop ACD indicates that the curve AC can be transformed to the curve CF through a 180° rotation about point C. Hence for modelling purposes it is sufficient to consider a quarter of a loop, AC. Figure 3.3 illustrates two interlacing loops. The course direction is along the horizontal x-axis while the y-axis defines the wale direction. The origin is taken at point B. The forces and moments at point B results from external forces and reaction forces due to interaction of knitted loops and that may include friction and forces applied along the course and/or wale direction. One important feature is the direction of the reaction force at point B, for example. If it has a vertical component there would be a fabric tension along the wale direction that would require an external force to balance it. Such vertical components would therefore be absent in relaxed fabrics or when external forces are applied along the course direction only. Hence in the latter cases reaction force at B runs along the horizontal x-axis/course direction. In Fig. 3.3, Fw and Fv are, respectively, the internal force components along and perpendicular to the tangent to the centreline. The equivalent force-moment equilibrium diagram, with forces and moments acting at B, is shown Fig. 3.4.
© Woodhead Publishing Limited, 2011
Modelling of knitting
3.3 Two interlacing knitted loops.
3.4 Equivalent force diagram. © Woodhead Publishing Limited, 2011
53 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
54 1 2 3 4 5
Advances in knitting technology
The additional moment
for yarn diameter d gives rise to the
difference in initial curvatures at point B for the elasticas BA and BC. Further, concerning path BC the curve is straight at C, i.e. curvature p = 0 at C, and the x-coordinate at C is
. The angle β is the interlocking angle. The latter are
two boundary conditions that are required to find a solution for the relaxed and strained fabric. In the case of external force acting along the wale direction or absence of external forces, the shape of segment BA is a circular arc. The shape of the loop is obtained by assuming that the yarn is an elastica and therefore, under the effect of forces and moments, will satisfy the elastica equations. The yarn is treated as two separate elasticas, BA and BC, and the paths of these parts are obtained separately using the elastica model. The moment acting at B on elastica BA is generally not the same as that at B for elastica BC, i.e. the curvature is not continuous at B. The elastica model for extensible thin filaments is described in the next section followed by its application to knitted loop mechanics.
3.3.2 Planar inextensible elastica: governing equations The equations for inextensible elasticas are derived in terms of a number of first order differential equations, as the latter are more amenable to integration by numerical methods. Figure 3.5 shows a small segment of length ds of a loop with internal forces and moments balanced.
2 3 4 5 6 7 8 9 40 1 2 43X
3.5 Small element of knitted loop.
© Woodhead Publishing Limited, 2011
Modelling of knitting
55
From differential geometry: [3.9]
[3.10]
[3.11]
Taking moments about centre of element in Fig. 3.5 gives:
[3.12]
[3.13] Since M = Eb.p where Eb is the bending rigidity, equation 3.13 can be rewritten as follows: [3.14] Owing to equilibrium of forces on the element in Fig. 3.5: cos(d θ) ≈ 1, sin(dθ) ≈ dθ and neglecting second order terms:
[3.15]
[3.16]
[3.17] [3.18]
Finally bending energy, Ub, is given as follows:
[3.19]
3.3.3 Load-deformation behaviour of plain knitted fabrics An increasing load is applied to the knitted fabric in regular small increments, along the course or wale direction, and the deformation simulated. The model is divided into two stages. In the first stage there is no slippage at contact points. During the second stage slippage occurs when the tangential force at the contact
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
56 1 2 3 4
Advances in knitting technology
point exceeds the frictional force. At each step guess estimates of curvature, load, interlocking angle or arc lengths are required. The values of the previous steps provide the estimates. For the first loading step a procedure to compute the guess estimates for curvature, load, and arc lengths is described in the Appendix. Point B in Fig. 3.3 is taken as the origin.
3.3.4 Coursewise deformation No slippage The unknown initial values are curvature pc(0) of elastica BC in Fig. 3.3, reaction load FX at B and interlocking angle β. To simulate the loading process guess estimates are provided for these parameters and Newton–Raphson’s iterative process is used to improve the estimates to a specified accuracy. Loop slippage Slippage occurs when frictional force is exceeded at contact points. The condition for slippage is tan(β ) ≥ Coefficient of Friction. During the slippage phase the interlocking angle remains unchanged and is equal to the value at the start of slippage. The path lengths LBC and LAB in Fig. 3.3 change mainly because of loop deformation. For modelling loop deformation mechanics with yarn slippage, the unknown variables that will have to be estimated prior to using the elastica model are the curvature pc(0), the external force FX acting at B of loop part BC and the length LBC. Initial values for loop segment BA [3.20]
[3.21]
[3.22]
3 4 5 6 7 8 9 40 1 2 43X
[3.23] Fcourse is the external force applied along the course direction that coincides with the x-axis direction.
[3.24]
[3.25]
Initial values for loop segment BC
[3.26]
[3.27]
© Woodhead Publishing Limited, 2011
Modelling of knitting
57 [3.28]
[3.29] [3.30]
3.3.5 Model: walewise deformation External forces are applied on the loop along the y-axis/wale direction. For modelling purposes the load is increased in small steps and at a given loading the guess estimates for unknown initial parameters are the values evaluated at the preceding step. The external load is applied in the y-direction. The vertical force component at B is half the wale load per loop. The main difference with the previous model for coursewise deformation is that the reaction or interlacing force acting at B will have a vertical component. For the previous model the interlacing force acts along the horizontal, i.e. the x-axis. The angle between the interlacing force and the x-axis is as follows: ,
[3.31]
where FX is the horizontal component of reaction load at B. As in the case for coursewise deformation the no slippage and slippage situations are considered separately. No slippage The unknown initial values are the initial curvature pc(0) and internal load FX on segment BC as well as the interlocking angle β. As in the case for coursewise deformation the model for no slippage is slightly different to the situation when frictional force is overcome and the loops slide past each other. Slippage The condition for slippage is tan(β + θ) ≥ Friction Coefficient. Hence slippage occurs earlier for walewise deformation compared to coursewise elongation. When the loops start to slide the interlocking angle remains fixed while the segments lengths LBC and LBA are treated as unknown initial values just like for coursewise deformation. Initial values for loop segment BA [3.32]
[3.33]
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
58 1 2 3 4 5 6 7 8
Advances in knitting technology [3.34]
[3.35] Fwale is the load applied in the wale direction.
[3.36]
[3.37]
As in the case for the relaxed loop, no external force acts at point A; hence the loop part BA will maintain a circular shape. Initial values for loop segment BC
[3.38]
[3.39] [3.40]
[3.41]
[3.42]
3.3.6 Computational aspects
2 3 4 5 6 7 8 9 40 1 2 43X
The models for plain knitted fabric have been reduced to solving the elastica problem. The solution involves a numerical integration of a set of differential equations, given the initial values of the parameters. In the case of both coursewise and walewise deformation with or without slippage, three initial values are unknown. The resulting boundary value problem is solved by the Newton– Raphson’s method. After each run of the integration certain parameters are compared with specified boundary values. The definition of these boundary values is unique to each elastica problem. For knitted loop mechanics the following boundary conditions are defined: • Curvature at point C, in Fig. 3.3, is 0.0. • The x-coordinate of point C in Fig. 3.3 is
.
• Direction cosine at point A, in Fig. 3.3, along the y-axis is 0.0. Given these boundary conditions we can construct three functions: [3.43]
© Woodhead Publishing Limited, 2011
Modelling of knitting
59 [3.44]
[3.45]
where A and C are points on the knitted loop defined in Fig. 3.1. Let’s say the three unknown parameters are X1, X2 and X3 where X1 is the unknown initial curvature at point B of segment BC; X2 is the unknown external load at point B of segment BC; X3 is the unknown interlocking angle or length LBC. Using the Newton–Raphson procedure:
[3.46]
The values of ∆X1, ∆X2 and ∆X3 are obtained using the Gaussian elimination procedure. Improved estimates for X1, X2 and X3: Xi = previous estimate Xi + ∆Xi. Figure 3.6 shows the computational results for load applied in the course direction. The load is normalised to the dimensionless value
3.4
.
Mechanics of plain-weft knitted fabrics: 3D model
The previous model assumes that the loop is planar. A more realistic model would consider the 3D nature of the loop geometry. The knitted loop in this case is represented by a three-dimensional elastica, which coincides with the centrelines of the yarns. The equilibrium of the yarn is described by a set of differential equations. The yarn is assumed to be homogeneous, perfectly elastic in bending and torsion, inextensible, undeformed by shear, initially straight, massless and frictionless with a constant circular cross-section. Stress–strain relationships are given by application of the ordinary approximate theory of bending used by Love.7 The treatment of elastica theory, crucial to the force–equilibrium methods, based on the work of Konopasek and Hearle,6 is first described, followed by the 3D knitting model based mainly on the work of Hepworth.8
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
60
Advances in knitting technology
1 2 3 4 5
3.6 Load-extension of knitted fabrics for different L/d ratios.
3.4.1 Elastica theory The objective is to describe the shape of the centreline of an elastica subjected to external forces and moments. The obvious way of describing a 3D-curve is in terms of a moving trihedron (t, n, and b), where t is the tangent to the curve, n the principal normal and b the binormal vector. Any point of the space curve is represented by the position vector r(s), a function of arc length s. The derivatives of the moving trihedron are the Serret–Frenet formulas: [3.47]
4 5 6 7 8 9 40 1 2 43X
[3.48] [3.49]
D is the Darboux vector and is defined as D = kb + τ t The Serret–Ferret equations define the curvature, k, and torsion τ of a curve, which are both purely geometric quantities. However, what is required for the study of an elastica are measures of curve which relate to both geometry and mechanical properties of the thin rod. A new moving trihedron (u, v and w), based on the Serret–Ferret frame is defined as follows:
© Woodhead Publishing Limited, 2011
Modelling of knitting
61 [3.50]
[3.51]
In practical situations the vectors u and v represent the principal directions of the elastica cross-section and vector w is the tangent of the centreline of the elastica. The angle λ varies along the centreline and hence is a function of arc length s. With this change of local coordinates the following differential equations can be derived to express the geometry of a curved elastica in three dimensions in terms of cross-section parameters and twist.
[3.52] [3.53] [3.54]
where: ψ = pu + qv + σ w, analogous to the Darboux vector; p and q are components of curvature in the u and v directions; σ is the twist, relative displacement of two neighbouring cross-sections. Constitutive equations The elastica is assumed to be inextensible, of constant cross-section and unaffected by shear. In that case the elastica shows resistance to bending and torsion according to Love’s ‘Ordinary Approximately Theory’.
[3.55]
[3.56] [3.57]
where:
Mu and Mv are the components of internal moments and A and B are the bending rigidities; Mw is the internal torque and C is the torsional rigidity. Moment and force equilibrium equations The vector form of equations of equilibrium of forces and moments on a small element shown in Fig. 3.7 are as follows:
© Woodhead Publishing Limited, 2011
[3.58]
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
62
Advances in knitting technology
1 2 3 4 5 6 7
3.7 Elastica element.
[3.59]
where: M is the concentrated moment; F is concentrated force.
Within a moving basis, such as the [u, v, w] the equations 3.58 and 3.59 have to be modified as follows to yield:
5 6 7 8 9 40 1 2 43X
[3.60] [3.61]
Combining equations 3.60 and 3.61 with the constitutive equations relate the geometric parameters, curvature and twist to external loads and moments. Hence the complete mathematical model of three-dimensional elastica consists of equations 3.52 to 3.54, equations 3.60 and 3.61 modified by the constitutive model and equation 3.62 below, which relates the local coordinates to the Cartesian viewpoint (x, y and z):
© Woodhead Publishing Limited, 2011
Modelling of knitting .
63 [3.62]
In scalar form the model consists of 18 first-order linear differential equations.
3.4.2 Geometrical aspects of knitted loop Due to the symmetry of the knitted yarn only the quarter of a loop needs to be considered. Figure 3.8 below shows the interlacing of two loops A1B1 and A2B2 at two different angles. In the interlacing region, because the yarn is incompressible, contact occurs at two points, C and D, at which the normals to the yarn surfaces cut the centrelines at points C1, D1, C2 and D2. In the absence of friction these normals are the lines of action of the inter-yarn forces at these points that by symmetry have equal magnitudes P. If the direction cosine of the force at D is ( fx, fy, fz) with line of action C2D1 then the force at C is along C1D2 and its direction cosine is ( fx, –fy, fz). Since YD1 – YC1 = fy*d and YD1 = YD2, from symmetry consideration we therefore have: [3.63] The point E is midway between C and D. From Fig. 3.8, again due to symmetry, we have: .
[3.64]
But
and
. Hence: .
3.8 Interlacing knitted loops.
© Woodhead Publishing Limited, 2011
[3.65]
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
64 1 2 3 4 5 6 7 8
Advances in knitting technology
Further: .
[3.66]
Hence: .
[3.67]
In the case of jamming the inter-yarn force Qc is parallel to the z–x plane and goes through the contact point Jc as shown in Fig. 3.9. The direction cosine of the line of action of Qc is say (–ax, 0, –az). XB2 = XJC and ZB2 = ZJC, i.e. symmetrical. The point JC1 lies on the centreline of loop A1B1 along the line of action of Qc. It is obvious from Fig. 3.9 that the distance between JC and JC1 is d/2. [3.68]
Also using equation (3.67) we have: .
5 6 7 8 9 40 1 2 43X
3.9 Jamming of knitted loops. © Woodhead Publishing Limited, 2011
[3.69]
Modelling of knitting
65
Therefore: .
[3.70]
Hence: .
[3.71] When loop A1B1 touches the adjacent wale at JW the line of action of force Qw is parallel to the z-axis and meets the yarn centreline at JW1. . By symmetry ZJW – ZA1 = 2*(ZB1 – ZA1). Hence: .
[3.72]
3.4.3 Equilibrium of forces and moments The only force at A1 is the tension parallel to the z-axis and a bending moment perpendicular to the z-axis. This is because the loops are symmetrical and therefore there is no twisting couple and shear stress at A1. Similarly at B1, where the tangent at the centreline is parallel to the z–x plane, there is no bending moment and shear stress parallel to the y-axis. Suppose Tc and Tw are the externally applied loads on the fabric per course and wale respectively. Further, let the inter-yarn force at C and D be P. Then the tension at A1 is Qw + Tc, parallel to the z-axis. Component of tension at B1 in the x-direction is: .
[3.73]
Component of tension at B1 in the z-direction is: .
[3.74]
If half a loop is considered the resultant force in the x-direction is half the external force per wale. This force is balanced by loop inter-forces at C and D and the force Qc at two course-jamming points. Hence: .
[3.75]
3.4.4 Method of solution The differential equations describing a 3D elastica are integrated from A1 to JC1. The coordinates at A1 are taken as the origin. The tangent to the curve at A1 makes
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
66 1 2 3 4 5
an angle of π to the z-axis. Not all the initial conditions at A1 are available. The curvature component p and the jamming force Qw are unknowns and so estimates must be provided at this stage. Furthermore, the length L1 of the loop from A1 to JC1 is also an estimate. The second integration is from JC1 to C1. The magnitude of the inter-force Qc is not known and has to be provided as an estimate. The orientation of Qc is perpendicular to the tangent at JC1, which is obtained from the first integration. Again the length, L2, for the integral is an estimate. The third integration is from C1 to D1. The magnitude of inter-force P is obtained from equation 3.75 above. Its orientation is perpendicular to the tangent at C1 obtained from the second integral. The length, L3, of the curve from C1 to D1 is provided as an estimate. The last part of the integration is from D1 to B1. The length of the integration is obtained from the difference of a quarter of the loop length, L, which is given, and the sum of the estimates L1, L2 and L3. To perform the integration in stages from A1 to B1, we need to give estimates for a number of unknown parameters: L1, L2, L3, Qw, Qc, and p; hence the loop calculated is only approximate. To obtain a more accurate loop, sufficient boundary conditions are required to improve the estimates. These boundary conditions are the equations derived from geometric considerations (equations 3.63, 3.65, 3.70 and 3.72) and also the condition that the component of curvature, p, at B1 is zero. These conditions are just enough to solve the boundary value problem to obtain an accurate loop. The general procedure of solving this type of problem is discussed in more detail for the solution of the 2D-loop mechanics problem in the section below. In brief, the procedure involves iterating the four-stage integration. At the end of every iterative cycle the boundary conditions are verified. If they are satisfied within predefined tolerance the iteration is terminated and the final loop A1B1 is accepted. Otherwise the parameters estimated are improved using the standard Newton–Raphson method.
3.5
5 6 7 8 9 40 1 2 43X
Advances in knitting technology
Knitted fabric mechanics: energy model
One of the shortcomings of the previous mechanical models concerns the nature of the contact between the yarns. This is assumed to be a single point for the 2D-model and two-point for the 3D-model. In reality the situation is far more complex. The energy model developed by De Jong and Postle9,10 handle this issue far more comprehensively. In general, the energy method attempts to model fabric mechanics by formulating and minimising equations of potential energy in a fabric subjected to external loading. De Jong and Postle9,10 presented a general theory of elastic behaviour of fabrics based on modelling the shape of deforming yarns. The energy model developed in this section is adapted from their work. They assume linear elastic deformation properties of the yarns, and that any fabric structure consisting of those yarns comes to equilibrium in a minimum energy configuration.
© Woodhead Publishing Limited, 2011
Modelling of knitting
67
3.5.1 Formulation of Hamiltonian function We have six state variables z1, z2 . . . z6 which describe our system, in this case a knitted loop. These variables, except for z6, are shown in Fig. 3.10. In addition three control variables, m1, m2 and m3 are at our disposal. The state variables satisfy the ordinary differential equations: [3.76]
[3.77]
[3.78] [3.79]
[3.80] . [3.81] The derivatives are with respect to the arc length s, the independent variable.
3.10 Coordinate system.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
68 1 2 3 4 5 6 7
Advances in knitting technology
We wish to choose function mk(s), k = 1, 2 and 3 in order to minimise the functional: [3.82] where U is the total energy per unit bending rigidity; B is the bending rigidity; G is the torsional rigidity; C is the compression rigidity; r is the measure of distance between two yarns in contact. Given the above definitions of state and control variables the curvature, Κ is as follows: .
[3.83]
The torsion θ is: [3.84] The functional can then be expressed in terms of variables zi and mi as follows:
[3.85]
This function has to be minimised subject to the following constraints: . 3 4 5 6 7 8 9 40 1 2 43X
[3.86] [3.87]
and z(s) are the coordinates of two yarn elements in contact. where It is often convenient and certainly more elegant to introduce the Hamiltonian function H defined as: [3.88] The Lagrange multipliers λi are related to H through the canonical equations. [3.89] [3.90] © Woodhead Publishing Limited, 2011
Modelling of knitting
69
The expanded Hamiltonian H is therefore:
[3.91] The terms
are obtained from the state equations. For example, . The other terms are constructed in the same way.
To obtain the Hamiltonian H is differentiated with respect to zi. For example in case of we have: [3.92] But: .
[3.93]
Hence:
[3.94] Therefore: [3.95] Proceeding in a similar fashion we get: [3.96]
[3.97]
[3.98]
[3.99]
[3.100] The above equations (3.95 to 3.100) are known as the costate equations. © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
70 1 2 3 4 5 6
Advances in knitting technology
3.5.2 Equilibrium equations The functions mk (s), k = 1, 2 and 3 which minimise functional U make the Hamiltonian H stationary for all s: 0 ≤ s ≤ L. H is constant along the optimal path and the constant has value zero when the limit L is not specified according to Pontryagin’s minimum principle []. The functions mk (s) cause U and therefore H to take a minimum value when: .
[3.101]
This condition yields the following relationships: [3.102]
.
[3.103] [3.104]
3.5.3 Method of solution Guess functions for m1, m2 and m3 are used to integrate the state equations and therefore to solve the loop geometry. The shapes of adjacent loops are obtained to determine the distance r between loops. Then the costate equations are integrated to obtain the Lagrange multipliers along the whole path. Minimum energy is achieved if the following condition has been reached:
. If this
condition is not satisfied then the values mi are improved according to:
[3.105]
where: 3 4 5 6 7 8 9 40 1 2 43X
In the case of the knitted loop the integration path is along a quarter of a loop due to the symmetry of the loop. The symmetry condition holds if we neglect yarn twist. In that case five state and five costate equations are required to define the
© Woodhead Publishing Limited, 2011
Modelling of knitting
71
quarter loop geometry as m3 and λ6 are equal to zero. The costate variables, though arbitrarily included in the Hamiltonian, do have actual physical meanings. The first three costate variables refer to shear forces while λ6 to λ3 are moments. To integrate the state and the costate equations we need the boundary values so as to compute the integration constants, and we also need to define the compression function g(r). The coordinates at point B on the loop, Fig. 3.11, is defined as the origin so that zi = 0 for i = 1 to 3. At B the component of curvature in the Z1–Z2 plane is zero which sets z4 = 0. Further, the curvature at A in the Z1–Z3 plane is zero which in this case sets z5 = 0. The value of λ1 at A is the external force applied per course in the course direction, i.e. the Z1-axis. The reaction force at A in the Z2 direction is zero so that λ1 is zero at A. Further, at A, λ3 is the transverse force applied to the fabric. At B, the tangent to the curve is the Z1–Z2 plane. The curve in the Z2–Z3 plane at B is stationary. The control variable m1, which defines rotation in the plane containing the tangent and the Z1-axis, is therefore zero at B. This implies from the equilibrium equation that λ4 is zero at B. Similarly at A we have a stationary point, which means that the control variable m2 is zero. Again we can deduce from the equilibrium equation that λ5 is zero at A.
3.11 Projections of loop.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
72 1 2 3 4 5 6
Advances in knitting technology
The authors9,10 have defined the compression energy per unit of compression , where a is the compression index and varies for different rigidity as yarns. The boundary conditions and the compression function definition are sufficient to integrate the state and costate equations numerically for guess estimates of the control functions. The iteration proceeds until the change of the Hamiltonian with respect to the control variables, that is, the energy gradients are zero within the required tolerance over the whole quarter loop.
3.6
Knitted fabric pressure on a surface
Knitted fabrics are increasingly used for a wide variety of applications ranging from composites’ parts to wearable medical devices. Sensors are knitted into the fabric to monitor the heart rate and other physiological parameters. For medical devices the pressure profile of the garment on the wearer affects the quality of the signals being measured. The model developed in this section assumes that a knitted fabric behaves like a membrane, that is, bending is ignored.
3.6.1 Curved membrane mechanics Tensor T is the stress tensor. The force acting on element ds, in length, and with unit normal e, is T.eds as shown in Fig. 3.12. For equilibrium: [3.106]
where: n: unit normal to surface p: pressure Using divergence theorem:
4 5 6 7 8 9 40 1 2 43X
[3.107]
,
[3.108]
given dS is arbitrary. Assume stress tensors vary only with the coordinates (u, v) of the membrane:
[3.109]
a and b are each either u or v; gu and gv are the curvilinear base vectors. In general:
© Woodhead Publishing Limited, 2011
[3.110]
Modelling of knitting
73
3.12 Membrane subjected to pressure and edge forces.
where: is the surface covariant derivative of tensor T; are the components of the surface curvature tensor. [3.111]
where:
[3.112]
Equations in curvilinear coordinates The first tensor equation, as follows:
, can be expanded into a set of four equations
[3.113]
© Woodhead Publishing Limited, 2011
[3.114]
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
74
Advances in knitting technology
1 2
[3.115]
[3.116] The second tensor equation Kαβ Tαβ + p = 0 is equivalent to the following:
[3.117]
3.6.2 Differential geometry [3.118]
[3.120]
[3.121]
[3.122]
[3.123] [3.124]
[3.125]
[3.126]
2 3 4 5 6 7 8 9 40 1 2 43X
[3.119]
[3.127]
[3.128]
[3.129]
Christoffel symbols
[3.130]
© Woodhead Publishing Limited, 2011
Modelling of knitting
75 [3.131]
[3.132] [3.133] [3.134] [3.135] Surface definition [3.136]
[3.137]
[3.138]
[3.139] where
[3.140]
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
76 1 2 3 4 5 6 7
Advances in knitting technology
HT is the transposition of matrix H:
[3.141]
. Matrix A is a 4 × 4 matrix and is defined as follows:
[3.142]
[3.143]
[3.144]
[3.145]
3 4 5 6 7 8 9 40 1 2 43X
[3.146] [3.147]
© Woodhead Publishing Limited, 2011
Modelling of knitting
77
3.6.3 Application to knitted fabrics The objective is to compute the pressure distribution, given the fabric’s tensile properties. In this case only the second tensor equation is necessary, i.e. Kαβ Tαβ + p = 0, which is equivalent to: [3.148] If we assume that wales and courses remain orthogonal on the body, i.e. wales follow the u-curves and the courses the v-curves, then shear force can be neglected and the pressure equation is simplified to: [3.149] The tensile components are obtained experimentally. Hence it is convenient to rewrite the above equation in terms of physical components. Physical components of curvature tensor are: [3.150] [3.151] The physical components of the tensile components are: [3.152]
Replacing in the above equation:
[3.153]
[3.154]
3.6.4 Experimental data Knitted fabrics have been tested in tubular form using special grips designed for this purpose. The stress–strain property of a typical fabric in the course direction is shown in Fig. 3.13 below. The stress–strain relationship in the wale direction is also required. To obtain the stress profile for a fabric deformed in a specified manner, a cubic polynomial is fitted to the stress–strain data. This approach is simple and saves on computation time. Suppose the number of experimental data is N, and stress is represented by Y and strain by X, then the following parameters are defined in the set of equations 3.155.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
78
Advances in knitting technology
1 2 3 4 5
3.13 Actual stress–strain characteristics of fabric.
[3.155]
4 5 6 7 8 9 40 1 2 43X
The coefficients, pi, of the cubic polynomial are obtained by solving the following set of linear equations:
[3.156] The stress–strain relation is then: . © Woodhead Publishing Limited, 2011
[3.157]
Modelling of knitting
79
3.6.5 Stress–strain and pressure profile A knitted fabric made of elastomeric yarns of known initial width and length, when worn, will conform to the shape of the body if the undeformed dimensions of the garment are less than the body size. The initially flat fabric is deformed to the profile of the wearer’s body, which is represented digitally through 3D-scanning and the post-processing described above. The strain along a given wale or course is constant but because of the complex geometry of the body the strain will vary, in general, between courses and wales. The course strain profile is obtained by computing the length of each cross-section, i.e. the v-curves and comparing with the undeformed length. The wale strain is the difference between the curve length connecting two extreme points along a u-curve on the body and the vertical distance between these points. The metric curvature tensor is computed at the intersection of the u–v curves or coordinate system. The physical components of this tensor as well as the tensile tensor are used to obtain the pressure profile. Pressure is given as: ,
[3.158]
where: is the stress component tangential to the v-constant lines, i.e. the stress in the courses, is the stress component tangential to the u-constant curves, i.e. the stress in the wales. Figure 3.14 shows the pressure of a garment on a body.
3.14 Pressure profile on hemispherical surface.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
1 2 3 4 5 6 7 8 9
80
Advances in knitting technology
3.7
Heat and water vapour diffusion in fabrics
Heat is lost through clothing by a variety of transport mechanisms which interact and occur together. In the absence of water the main heat flow mechanisms are conduction by trapped and thermal radiation. When water is added to the system, by sweating or otherwise, other heat loss mechanisms have to be considered. Heat conduction is of importance if sufficient water is present in the clothing. Evaporation and diffusion of the water vapour is the predominant heat loss mechanism when water is present in the clothing. The numerical model of Farnworth11 is discussed in some detail in this section. However, before describing the model it is important to list the main assumptions: • Regain is proportional to relative humidity. • The three forms of water that is vapour, liquid and absorbed, are in equilibrium.
3.7.1 Theoretical background The basic theory of heat loss through clothing treats heat loss from the skin by radiation and conduction on the one hand and by evaporation on the other as simultaneous but separate phenomena. Hollies and Goldman12 suggested the following equations:
[3.159]
,
[3.160]
where:
2 3 4 5 6 7 8 9 40 1 2 43X
kc is the coefficient of convective heat transfer; ke is the evaporative coefficient; Psk is saturated vapour pressure at skin temperature; Pab is saturated vapour pressure at dry ambient skin temperature; Tsk is mean skin temperature; Tab is dry bulb ambient temperature; A is the surface area of the body. The equations are expressed in term of heat transfer resistance
and
. The total heat loss per unit area QT is then of
moisture transfer resistance the form:
[3.161]
The two forms of heat loss from the skin, conduction and evaporation, are not independent. There is the possibility of condensation within the clothing layer or layers if vapour permeability is low and ambient temperature is low. Evaporation
© Woodhead Publishing Limited, 2011
Modelling of knitting
81
can occur, not only from the skin but also from within the clothing, if say sweat has condensed in it. The simple equation for total heat loss is generalised to partial differential equations for heat and vapour flows as functions of time and distance from the skin. For clothing systems made up of more than one layer a differential equation for flows with time will suffice if instead of distance the equations are expressed for a given layer. [3.162]
where
Rci is heat transfer resistance of layer i; Ti is temperature of layer i; Qci is quantity of heat per unit time per unit area liberated by layer i; Ci is heat capacity per unit area of layer i. For flow of vapour a similar equation is as follows: ,
[3.163]
where
for layer i. Pi: Vapour pressure at layer i.
3.7.2 Relationship between pressure and mass and temperature The amount of water (Mi) present in a layer can be in different forms: vapour (Mvi), liquid (Mli) or absorbed by the fibres (Mai). Hence: [3.164] Assuming the vapour behaves like an ideal gas, then using the ideal gas law we have: .
[3.165]
Xi is the thickness of layer i, and fi is the fibre volume. So Xi(1 – fi) is the volume of unit area of the layer. The number of molecules is
as Mw is the mass of one
water molecule. The constant kB is the Boltzmann constant. If the mass of water absorbed is assumed proportional to the relative humidity then: .
[3.166] © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
82 1 2 3 4
Advances in knitting technology
On the left-hand side of the equation γi is the proportionality constant, and the relative humidity is the ratio of vapour pressure Pi to the saturation vapour pressure at the temperature Ti of the layer. The right-hand side of the equation is the ratio of mass of water absorbed to mass of layer i. If water is not present in liquid form in the layer then using equations 3.165 and 3.166 we get: [3.167]
Hence:
[3.168]
.
If there is liquid water the vapour pressure Pi = Ps the saturation vapour pressure at Ti. In that case the maximum amount of water present as vapour and absorbed is given as follows: .
[3.169] To summarise, the relationships between vapour pressure on one side and temperature and mass on the other are: when Mi < M imax Pi = Ps when Mi > M imax.
3.7.3 Calculation of heat of condensation 4 5 6 7 8 9 40 1 2 43X
When Mi > M imax then all the water accumulates as liquid by condensation. Then the heat released is given by: [3.170] where H is heat of vaporisation per unit mass. When Mi < M imax then water is partly vapour and partly absorbed. Then:
[3.171]
© Woodhead Publishing Limited, 2011
Modelling of knitting
83
Hence: ,
[3.172]
where Ha is the heat of sorption.
3.7.4 Method of solution The first differential equations (equations 3.162 and 3.163) can be expressed in terms of mass, temperature and time. They can be solved numerically a layer at a time. The properties for each layer, heat and vapour resistances, heat capacity and regain are provided together with the initial values of surface and ambient temperatures and mass. There are several methods for determining the resistances of the clothing.11,12 For the initial conditions, the temperature distribution can be calculated by dividing up the total temperature difference between surface and environment proportionately according to the heat resistance of each layer. The vapour pressure is taken as that of ambient air and the masses of water calculated from the temperature and pressure of each layer (equations 3.166 to 3.168).
3.8 1. 2. 3. 4.
5.
6. 7. 8. 9.
10.
11.
References Doyle, P. J. J. 1953. Fundamental aspects of the design of knitted fabrics, Textile Institute, 44, P561. Munden, D. L. 1959. The geometry and dimensional properties of plain-knit fabrics, J. Text. Inst., 59, T448. Leaf, G. A. V. and Glaskin, A. 1955. The geometry of a plain knitted loop. J. Textile Inst., 46, T587, Shanahan, W. J. and Postle, R. A. 1974. Theoretical analysis of the tensile properties of plain-knitted fabrics. Part 1: The load-extension curve fro fabrics extension parallel to the courses. J. Text Inst., 65, 200–212. Shanahan, W. J. and Postle, R. 1974. A theoretical analysis of the tensile properties of plain-knitted fabrics. Part 2: The initial load-extension behaviour for fabric extension parallel to the wales. J. Text Inst., 65, 254–260. Konopasek, M. and Hearle, J. W. S. 1972. Fibre Science and Technology, 5, pp 1–28. Love, A. E. H. 1944. A Treatise on the Mathematical Theory of Elasticity, Dover, New York. Hepworth, B. 1978. The biaxial load-elongation behaviour of a model of plain weft knit. J. Textile Inst., 69, 101–107. de Jong, S. and Postle, R. 1977. An energy analysis of the mechanics of weft-knitted fabrics by means of optimal-control theory: The nature of weft-interlocking in the plain-knitted structure. J. Textile Inst., 68, 307–315. de Jong, S. and Postle, R. 1977. An energy analysis of the mechanics of weft-knitted fabrics by means of optimal-control theory: Relaxed-fabric dimensions and tensile properties of plain-knitted structure. J. Textile Inst., 68, 316–323. Farnworth, B. 1986. Numerical model of the combined diffusion of heat and water vapour through clothing. Textile Research Journal, 56, 653. © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
84 1 2 3 4 5 6
Advances in knitting technology
12.
Hollies, N. R. S. and Goldman, R. F. 1977. Clothing Comfort: Interaction of thermal ventilation, construction and assessment factors, Michigan, Ann Arbor, Science Publishers Inc., U.S.
3.9
Appendix: initial guess estimates
The analysis in this appendix refers to the 2D mechanical model of knitted fabric described in section 4.2. Using the elastica model a data set is created for an initially vertical inextensible cantilever, which relates initial curvatures, the horizontal load applied and the displacement of the free end. The data are for a normalized beam, i.e. unit length and bending modulus. the direction cosines at the fixed end of the cantilever are given by the interlocking angle β. Table 3a.1 shows a sample of dataset for a small range of curvature values. The data are dimensionless and actual values depend on the bending modulus (Eb) and the length of elastica (L). Actual force is
, curvature , displacement =
.
If we consider the loop section BC, in Fig. 3.3, with B fixed, the x-coordinate of C is
. The dataset is searched to locate the cantilever that meets this boundary
condition most satisfactorily. However, to search the dataset of cantilevers the length L is required and this is not a priori known. Hence the algorithm described in the next section has been developed to obtain the length of BA and BC.
3.9.1 Algorithm to compute lengths of loop sections The length of loop section BC is obtained using the Newton–Raphson’s procedure. 1. A guess estimate of the length BC say LBC, is required to initiate the algorithm. A good estimate is one-eighth of the stitch length. 2. Curvature of loop section BA: ,
4 5 6 7 8 9 40 1 2 43X
[3a.1] ~ where p~ is the normalized initial curvature at B for elastica BC and F is the load acting at C. both values are obtained through searching the dataset of cantilevers for elasticas of length LAB as described in the previous section. 3. The loop part BA is circular in shape as no external forces are acting on it. Hence its length as given as: [3a.2] 4. Compute value of the function:
where SL is the stitch length. © Woodhead Publishing Limited, 2011
[3a.3]
Modelling of knitting
85
Table 3a.1 Cantilever dataset ˜ ˜ Load,F Curvature, p
Horizontal displacement, x˜
1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 2
0.26 0.29 0.32 0.35 0.38 0.40 0.43 0.45 0.47 0.50 0.52
1.05 1.17 1.29 1.42 1.55 1.68 1.83 1.97 2.13 2.29 2.46
5. If J > 0.001, then the new improved estimate of length AB is as follows: [3a.4] where:
[3a.5]
where ∆LBC is a small change in LBC. Steps 2 to 5 are repeated until the required precision is achieved, i.e. J ≤ 0.001.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
4 Intelligent yarn delivery systems in weft knitting R. KOVAR, Technical University of Liberec, Czech Republic Abstract: The chapter describes yarn delivery systems from different points of view. It begins with a theoretical analysis of yarn delivery, i.e. with a description of the main variables influencing changes in yarn speed and tensile stress during feeding. Passive (yarn tensioners) and active systems (yarn feeders) for yarn delivery are described in respect of the quality and stability of knitting production. Yarn feeders controlling yarn length (so-called positive) or yarn tensile stress (so-called negative) are introduced. The available intelligent systems and an overview of the main features of weft knitting and yarn feeding on circular and flat knitting machines are defined. Key words: yarn delivery, tensioner, feeder, friction, disc tensioner, storage feeder, elastan roller, creel, frictional feeder.
4.1
Introduction
Yarn delivery systems for weft knitting are very important parts of knitting machines. The main objectives of these systems are as follows: • To supply the machine with processed textile material, usually yarn, in sufficient quantities, to unwind the yarns from bobbins and to guide the yarns into the knitting mechanism. • To control the quantity of the yarn supply, i.e. the lengths and tensile stresses of the yarns. • To inspect the yarns from different viewpoints and to stop the machine if necessary. The knitting process will be interrupted if a break occurs in the yarn, if the tensile stress is too high or if the yarn becomes too thick in places. An efficient yarn delivery system is necessary for a reliable and stable knitting process. It specifically requires: • Reliability. The process must minimize the defects affecting fabric quality or causing lost time that lower machine utilization. (See Chapter 11.) • Stability. There should be minimal variation in the geometrical parameters of the fabric and its properties. These goals can be ensured only by the stability of the independent parameters of the knitting process, mainly the stability and quality of yarns (including yarn diameter) and by the stability of the lengths of the yarns in knitted elements (stitch lengths, etc.). Other geometrical parameters 89 © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
90 1 2 3 4 5 6 7 8
Advances in knitting technology of the fabric, such as wale and course density, dimensions of panels, fabric mass per square meter, etc., are dependent on previously mentioned parameters.
To ensure these conditions in available material of lower quality the tensile stress in the processed yarn should be the minimum required for reliable knitting. If the tensile stress is too low, there will be insufficient control of yarn geometry and a danger of snarling.
4.2
Theory of yarn delivery
In general, the yarn delivery system aids the stability of the knitting process by means of yarn length or yarn stress control. The mechanisms controlling these factors can be:3 • passive, without an energy supply and only able to increase tensile stress in yarns (so-called yarn tensioners or breaks); • active, with an energy resource that can either increase or decrease tensile stress in yarns (yarn feeders). Feeders can control and stabilize the supply of yarn length per fabric unit (positive feeding) or the yarn tensile stress (negative feeding). It is important for effective yarn delivery that yarn tensile stress increases in the stitch forming zone of the machine. Variation in speed of yarn consumption can also influence yarn tensile stress. Figure 4.1 shows the optimal situation for the stitch forming zone, in which only one needle (2) forms the stitch from yarn (1) over trick walls (3); (4) is the yarn guide (finger). The speed of the yarn feeding, vy, equals the sum of gradual changes of its segment lengths, l1, l2, l3, which results in Equation 4.1: ,
2 3 4 5 6 7 8 9 40 1 2 43X
4.1 Stitch forming zone on weft-knitting machine.
© Woodhead Publishing Limited, 2011
[4.1]
Intelligent yarn delivery systems in weft knitting
91
where vk is the speed of the knitting (machine working speed) and vn is the speed of the needle motion (vn = vk tan β, β is the actual angle of the stitch cam). Angles γ and δ are variable. Needle speed decreases to zero when the stitch forming is over. This results in the variable yarn speed vy with a frequency of changes corresponding with the frequency of individual stitch formation. The duration of one period is tp. Yarn tensile stress at guide F1 increases due to capstan (Euler’s) friction, when the yarn slips over the needle bed trick walls or sinkers (3), needle hooks (2) and previously knitted elements. It can be calculated approximately in accordance with Equation 4.2: [4.2] The friction coefficient f is variable over a wide range;2 yarn-to-yarn friction coefficient is usually greater than that of yarn-to-metal. The situation deteriorates if several needles form stitches at the same time (see Fig. 4.2). The yarn may easily reach its breaking stress value, which will result in casting off stitches and the formation of a hole in the fabric. A sudden increase in the tensile stress of the yarn can result in damage. It may be caused by a thick place in the yarn (such as a knot, nep, etc.). Yarn breakage can be partly prevented by so-called ‘robbing-back’ – a movement of the yarn in the opposite direction after a needle/needles are released and the relevant stitches shortened by yarn tension. In Fig. 4.2 robbing-back1,4 is shown at speeds v4, v5 and v6 in opposing directions. The disadvantage of robbing-back is a deterioration in the regularity of the fabric because the final shortening of stitches cannot be accurately controlled. Robbing-back can be prevented by the use of a stitch cam with a horizontal part (delay) at the end of the stitch formation zone. The number of simultaneously formed stitches depends on the stitch cam angle β, machine pitch (spacing) p and sinking depth h.
4.2 Yarn robbing-back in knitting.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
92 1 2 3 4 5 6 7 8 9
Advances in knitting technology
4.2.1 Passive yarn delivery systems The majority of passive yarn delivery systems (yarn breaks or tensioners) increase tensile stress by means of friction, which occurs when the yarn moves over a suitable frictional surface such as steel or ceramic. The disadvantage of this system is its sensitivity to irregularity of the yarn, mainly changes in its crosssection and a variable friction coefficient. An example of an additive tensioning system (frictional force Ff is added to original yarn stress F0) in Fig. 4.3a introduces a disc tensioner. Here the yarn (1) is held between two discs (2), which are pressed against each other by a normal force, Fn, which is generated either by a spring (3) or electromagnetically. The output yarn tensile stress can be calculated in accordance with: [4.3] where F0 is input yarn stress and f is friction coefficient. Multiplication by 2 is due to contact of two discs (left and right) with the yarn. A positive property of the disc tensioner is that variations in input yarn stress ∆F0 are not increased after passing the tensioner. (Friction force Ff = 2 Fn · f does not depend on yarn tensile stress F0), and so ∆F = ∆F0. Multiplying systems (in which the original yarn stress F0 is multiplied by a coefficient greater than 1) increase not only the actual tensile stress of the yarn, but also its variations. An example is shown in Fig. 4.3b, where the yarn is wound on the frictional cylinder (4) with an angle of contact α, that can be continuously changed by setting the position of the disc (5). Capstan (Euler’s) Equation 4.4 can be used (but note that the friction coefficient f is variable): [4.4] Variations in yarn stress ∆F increase in a similar manner and so Equation 4.5 can be used:
5 6 7 8 9 40 1 2 43X
4.3 Passive yarn tensile stress control.
© Woodhead Publishing Limited, 2011
[4.5]
Intelligent yarn delivery systems in weft knitting
93
The disadvantages of yarn slippage on frictional surfaces can be eliminated by using a kinetic tensioner. (See Fig. 4.3c.) Two rotary discs (6) increase yarn stress by break (7), independent of yarn properties. No yarn slippage occurs in this case. The shape of the disc (6) enables a zigzag movement of the yarn which increases the angle of contact. To improve evenness in output yarn tensile stress, compensation tensioners can be used. In this case, the frictional or breaking force Ff is controlled in accordance with yarn stress F. A higher value for F results in a decrease in Ff and vice versa. The yarn stress F can be detected by electronic sensors and the frictional force Ff changed electromagnetically. In this way it is possible partially to stabilize the axial stress of the yarn, although this will not be completely successful because the tensioners cannot decrease yarn tension. Similar systems for stabilization of the stitch length are described in section 4.4. Other techniques of yarn tensioning are seldom used. Pneumatic tensioners5 use an opposing air stream to increase yarn stress (Fig. 4.3d) but have the disadvantages of high cost and noise. Examples of compensation tensioners can be seen in Fig. 4.4. Figure 4.4a shows a ball tensioner, which increases yarn stress by holding the yarn between the steel ball (6) and the thread eye (7). A principle of compensation operates: when the input force F0 on the ball (6) is strong, gravitation is overcome and the clutch is released. The example in Fig. 4.4b consists of two independent parts. Both increase friction by wrapping the yarn (1) over metal or ceramic surfaces. Rings (3) hang on the yarn and their position depends on the tensile force in yarn F0. Increased yarn tension causes a higher positioning of the rings and thus a smaller angle of contact with the lower frictional force. The left mechanism has no compensation ability. The function of yarn breaks is replicated by yarn thread eyes, yarn guides, etc. An undesirable increase in yarn stress may cause problems in the knitting
4.4 Examples of compensation tensioners.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
94 1 2 3 4 5 6 7
Advances in knitting technology
process (greater frequency of yarn breaks, unevenness in the fabric, etc.) and is affected by the geometry of the yarn path from bobbin to knitting system. For elastomeric yarns, where small changes in tensile stress are connected with great strains (see Fig. 4.6), delivery systems are designed to have as short a yarn path as possible from bobbin to guide and thread eyes are replaced with small rollers.
4.2.2 Feeders with yarn length control (positive feeders) Feeders with yarn length control can be used only when the length of yarn per stitch in the stitch forming zone of the machine is constant (as in plain knitting). Measuring of the yarn improves the evenness of the fabric. For example, the effect of inexact adjustment or abrasion of the stitch cam can be partially eliminated. Greater sinking depth leads to an increase in yarn stress, thus shortening stitch length by an axial elongation of the yarn. There are several types of feeders with yarn length control. The most widely used are described below. Storage positive feeder
2 3 4 5 6 7 8 9 40 1 2 43X
The general advantage of storage feeders is that stored yarn prevents any transfer of changes in yarn stress (even those that may occur suddenly) across the feeder with their consequent influence on fabric quality. The length of stored yarn is usually sufficient for yarn feeding to continue, should the machine stop when an accident occurs (such as a yarn breakage at input to the feeder). Storage feeders will produce an immediate improvement in fabric quality. Yarn (1) is usually stored on a rotary winding reel or drum (2) in the form of certain number of winds or turns (see Fig. 4.5). Individual turns must not be crossed on the reel. As stored yarn is wound up on the upper side and unwound on the lower side, it is necessary to keep all the turns in a stable position by slippage all turns down (arrows). The simplest way to ensure this stability is by applying sufficient tension to the slippage conical part of the reel (3) F0 before the feeder. This is provided by the disc tensioner (4). Another effect of the disc tensioner (4) is to ensure more equal yarn elongation during winding. The feeder can ensure constant yarn length, but cannot recognize to what extent the yarn is axially strained. This is important mainly for high extensible yarns (elastomeric, textured yarns etc.). For example, if an elongation of 200% of the original length occurred, only 50% of the material would be fed through. This effect of the non-linear stress-strain curve is explained in Fig. 4.6a using a typical example for highly extensible yarns. At low axial stress, the change in tensile force ∆F1 has a greatly variable relationship to yarn elongation ∆ε1, whereas in the part of the curve with the greater yarn tensile force, the curve is steeper and the same interval of ∆F2 corresponds to a much
© Woodhead Publishing Limited, 2011
Intelligent yarn delivery systems in weft knitting
95
4.5 Storage feeder with length control (positive).
4.6 The effect of yarn tensile stress on quantity of yarn delivered.
lower change in yarn length ∆ε2. Figure 4.6b documents the changes in fed yarn due to elongation; L0 is the length of the relaxed part of the yarn, L is the the corresponding length of the yarn after extension and Ls is the length of the yarn measured for one stitch. The rotary movement of the storage reel (2) (Fig. 4.5) must be accurately adjusted to the machine motion. This condition can be met by the use of pulley (5) and belt (6). Usually one belt is used to drive several feeders on the circumference
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
96 1 2 3 4 5 6
Advances in knitting technology
of the machine. If different lengths of yarn need to be fed, a clutch (9) may be coupled with a pulley (7), driven by a belt (8) at a different speed, vb2. The yarn speed v = v0 corresponds to the peripheral speed of the reel; the output yarn tensile force is not directly controlled and so a yarn breakage sensor is required. The speed v must correspond with the speed of yarn consumption on the relevant cam system. Pulleys (5) and (7) and belts (6) and (8) need to be toothed or perforated to prevent slippage that would cause a change in the length of the fed yarn. Elastan roller In principle, this is an unwinding unit (see example in Fig. 4.7). Yarn (1) is unwound from the package (2) by two shafts (3) that move in the direction of the arrows. When slippage is prevented, the peripheral speed of the shaft and the yarn package is identical and the length of fed yarn well be controlled effectively if the yarn extensions are all in packages with a similar volume. A single unit is usually designed for feeding several yarns (in Fig. 4.7 it supplies bobbins (2), (4), (5) and (6), which may have different diameters). The feeder drive can be connected with a circular knitting machine motion as in the case of positive storage feeders (Fig. 4.5). Belt feeder The belt feeder was popular before storage feeders were developed. The yarn was gripped between the belt and the pulley and the speed of the yarn corresponded to the speed of the belt. The main disadvantages of this mechanism are a lack of stored material and the danger of transferring sudden changes in yarn tension or yarn breaks across the feeder with a detrimental effect on fabric quality.
3 4 5 6 7 8 9 40 1 2 43X
4.7 Elastan roller.
© Woodhead Publishing Limited, 2011
Intelligent yarn delivery systems in weft knitting
97
4.2.3 Feeders with yarn tensile stress control (negative feeders) Feeding of constant yarn lengths cannot be used where when the formation of rows requires variable lengths. As an example, a two-colour pattern is introduced with knit and miss back (Fig. 4.8). In this case, each yarn is knitted into three of a maximum of four stitches in areas of corresponding colour on the fabric face, but only into one of four stitches in areas of the complementary colour. This reduces yarn consumption by approximately one-third and for this reason, yarn tensile stress control (negative systems) are mainly used for patterned fabric knitting. Negative storage feeders The solution is similar to that shown in Fig. 4.5, but the yarn (1) is drawn off the reel (2) in the direction of its axis into the thread eye (8) (Fig. 4.9). As the yarn tensile stress would be too low for reliable control, a tensioning ring (7) is used on the feeder. This could be, for example, a ring with nails, slanted in the direction of the yarn balloon rotation. Yarn tension out of the feeder is so well controlled that a breakage sensor is not necessary on this side, but a detector for yarn breakage and high tensile stress should be used at the input side of the feeder. In comparison with positive storage feeders, there are several differences: 1) The speeds of the yarn before and after the feeder, v0 and v, are different. If a yarn break occurs before the feeder, the yarn may still be supplied to the knitting system until the machine is stopped.
4.8 Two-colour pattern with knit and miss back.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
98
Advances in knitting technology
1 2 3 4 5 6 7
4.9 Principle of negative storage feeder.
2 3 4 5 6 7 8 9 40 1 2 43X
2) The number of yarn turns on the reel may change and must be controlled by using an appropriate sensor. A motor drive (9), independent of machine speed, or a coupled belt drive may be used. If the number of turns is too small, the reel (2) increases the speed of its rotation and vice versa. 3) Differences between input and output speeds will cause false-twist, which can influence the quality of the fabric. This is the reason why some modifications were developed (see Fig. 4.10). Three basic variants are shown here: • Previously described system (Fig. 4.9) with rotary reel (2) causing falsetwist formation. • Fixed reel (3), winding the yarn through the rotary thread eye (4) from the lower side of the reel. All stored yarn turns must be moved up (arrows). • Fixed reel (5), winding the yarn through the rotary thread eye on the disc (6) from the upper side of the reel. All stored yarn turns are moved down (arrows). The design of the feeder is rather complex because the yarn balloon on neither the upper nor lower side permits fixed connection of the reel (5) with the frame. Remote control of the reel position can be ensured magnetically.
© Woodhead Publishing Limited, 2011
Intelligent yarn delivery systems in weft knitting
99
4.10 Basic systems of stored yarn supply.
4.11 Chosen ways of stored and wound yarn slippage (a, b); separated wound yarns (c, d).
Slippage of yarn winds towards the unwinding side (arrows) can be provided in different ways, for example by the conical part of the reel (Fig. 4.9), by the inclined ring (Fig. 4.11a) or by the wheel (Fig. 4.11b), etc. Systems have been developed that enable the separation of individual turns of yarn, for example the use of a set of two or more skewed cylinders instead of one (Fig. 4.11c) or of a set of belts (Fig. 4.11 d). All examples show both yarn length (P: positive) and yarn tensile stress (N: negative) control. Some storage feeders, available for knitting and for weaving machines, use an assembly of two mutually eccentrically mounted cages for the separation of wound yarn. There are two types of these eccentricities. First, mutual translation of the two axes insures that each cage carries the wound yarn only on a certain part of the feeder perimeter. Second, the bias position of the axes ensures that the yarn turns move in an axial direction.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
100 1 2 3 4 5 6 7
Advances in knitting technology
Frictional feeders In this case there is only a small number of yarn turns (1) (Fig. 4.12), so slippage between the yarns and the reel (drum) (2) is allowed. The reel is driven with peripheral speed vd, which is higher than the speed of the yarn, thus pushing it forward and decreasing its tensile force. The output yarn stress, F, can be counted using capstan (Euler’s) equation with the opposite sign of exponent, Equation 4.6
[4.6]
The advantage of this feeder is that variations in yarn tensile stress are decreased, because of ∆F = ∆F0 · e–α · f, (derived from Equation 4.6). The speed of the yarn supply can be changed over a wide range from zero up to the peripheral speed of the reel and so the system can be used for knitting different patterns or even in collaboration with a yarn striper. In yarn stress control mode, some use can be made of originally positive storage feeders set at a higher speed and with a small number of yarn turns (see subsection 4.2.2). Modification of this feeder for a flat machine will be introduced in section 4.4. Similarly, striper feeders can be used on machines that are equipped with a striper mechanism (exchange of yarn guides), Fig. 4.13. A feeder is equipped, instead of a reel or drum, with a set of discs (3), each controlling a single yarn. Discs are coupled in pairs to enable individual yarn control when two ends are threaded into one guide. Only one pair of yarns (1) is actually fed: in this example, the yarn tension swings the arm (4), thereby increasing the angle of contact. The
2 3 4 5 6 7 8 9 40 1 2 43X
4.12 Principle of frictional feeder.
© Woodhead Publishing Limited, 2011
Intelligent yarn delivery systems in weft knitting
101
4.13 Striper feeder: (a) horizontal view, (b) vertical view.
tension of the non-active yarns (2) is low so the arms (5) and springs (6) decrease the angle of contact of the yarn. Electronic feeders The use of electronic feeders enables quick and efficient regulation of yarn tensile stress. These systems are often based on the principle of storage feeders with
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
102 1 2 3
2 3 4 5 6 7 8 9 40 1 2 43X
Advances in knitting technology
control of reel rotation according to output yarn stress F, Fig. 4.14. Yarn (1) is wound on the reel (2), which is designed as a lightweight cage with self-cleaning abilities. Input yarn tension F0 is controlled by the disc tensioner (4). Output force F is measured by the sensor (3), which controls the motor drive (5). The motor reaction is so quick that the feeder allows knitting of patterned fabric and can be combined with a striper (yarn guide or finger exchange), which is standard equipment on hosiery machines. Some electronic feeders can be used on circular machines with reciprocated movement (for example in hosiery and body technologies). In this case, the feeder must allow backward yarn movement to compensate for shortening the length of the yarn path on the machine. In Fig. 4.14 this is achieved by the thread eye (6) mounted on a separately controlled arm. When the reel (20) moves backwards, the eye (6) turns in the same direction and keeps the input section of the yarn extended.
4.14 Outline of electronic yarn tensile stress control.
© Woodhead Publishing Limited, 2011
4.3
Intelligent yarn delivery systems in weft knitting
103
Yarn storage and delivery systems on circular knitting machines
The specific features influencing yarn delivery on large-diameter circular knitting machines are high productivity, continuous knitting and a great number of simultaneously processed yarns. Some of these machines are equipped with a striper (yarn guide exchange), but only a few enable reciprocated knitting. Small diameter hosiery machines have up to four (or occasionally eight) knitting systems (feeders) and an important feature is the combination of rotary and reciprocal movement of the needle bed (beds). Between these extremes are the middle diameter machines for ‘body’ technologies. Figure 4.15 shows the simplified yarn supply system on a large-diameter circular knitting machine. Yarns (1) are brought from the bobbins (2), passed through the side creel to the feeder (3) and finally to the yarn guide (4). Usually the feeder (3) is equipped with stop-motion sensors for yarn checking. The creel of the knitting machine controls the placement of yarn packages (bobbins) on all machines. Modern large-diameter circular machines use separate side creels, which are able to hold a large number of packages in a vertical position. Floor projection of these creels may differ (oblong, circular, etc.). If there is a long distance between the bobbin and the yarn guide, the yarns may be threaded pneumatically into tubes. The modular design facilitates the changing of the number of bobbins where required. Small-diameter machines with a smaller number of cam systems use either side creels or creels designed as integral to the machine. Modern creels make it possible to use double bobbins. Each pair of creel pins is centred on one thread eye (Fig. 4.16). The yarn of a new bobbin (3) may be linked to the end of the previous length of yarn (1) on bobbin (2) without stopping the machine. Some of the creels are equipped with systems for blowing off dust (fancreel), or with air circulation and filtration (filtercreel). The example in Fig. 4.17 shows the bobbins (2) in six rows, closed in a box with internal air
4.15 Outline of yarn feeding on a circular knitting machine.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
104
Advances in knitting technology
1 2 3 4 5 6 7
4.16 Double bobbins on creel.
3 4 5 6 7 8 9 40 1 2 43X
circulation, provided by fans (4) and tubes (3). A filter (5) clears dust from the air. The creel can be air-conditioned. When the machine is not equipped with a striper, this can be supplied by yarn exchange on the creel; some systems enable the knots to be positioned in the optimal area of the fabric. Yarn length control (positive feeding), when not used for patterned fabric knitting, must enable different yarn lengths to be fed into courses in different structures. As an example, in Milano-rib knit there is one double-faced course (1) and two single-faced (2), (3) courses in the repeated pattern (see Fig. 4.18). As a double-faced course contains twice as many stitches, the yarns must be fed at approximately twice the length per machine revolution. This is the reason why these feeders use several belts, individually adjusted for speed, whilst feeders using yarns of the same length are controlled by one belt. The feeders are usually mounted onto two or three rings around the machine. If a configuration with two belts on each ring is used (Fig. 4.5), yarns can be fed simultaneously at four or six speeds.
© Woodhead Publishing Limited, 2011
4.17 Cross-section of creel with internal air circuit.
© Woodhead Publishing Limited, 2011
105 1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
106
Advances in knitting technology
1 2 3 4 5
4.18 Milano-rib knit.
Feeders with yarn tensile stress control may use a belt drive with a clutch or an electronically controlled drive to regulate the number of turns of the yarn. When knitting plain rather than patterned fabric, there is a danger of striping due to uneven adjustment of the feeding of individual yarns. This necessitates the use of instruments for measuring the length of fed yarns and their tensile force. Some types of circular knitting machines enable 3D (spatial) knitting in different types of products. Three possibilities are considered here: 2 3 4 5 6 7 8 9 40 1 2 43X
• Hosiery products, including those for medical use. The number of needles cannot be changed so the 3D shaping of the fabric is achieved by controlling the length of fed yarn. For example, in the production of compressive stockings and similar products, the yarn delivery system is responsible for regulating the length of the inlayed elastomeric yarn so as to produce a compressive effect. • ‘Body’ technologies, often used in the manufacture of ready-to-wear products, use 3D shaping in which the number of needles in the machine bed is constant. Advanced yarn delivery systems are important in this process. • Single-knitting system (feeder) circular machines with rotary cams provide the advantage of both stable creel and needle beds. The yarn feeding system can be very simple. This type of machine is mainly used in the manufacture of technical products and dress accessories.
© Woodhead Publishing Limited, 2011
4.4
Intelligent yarn delivery systems in weft knitting
107
Yarn storage and delivery systems on flat knitting machines
Flat knitting machines characteristically offer efficient patterning and 2D and 3D shaping for smaller scale productivity. As flat knitting machines require a smaller quantity of yarn and fewer feeders or cam systems and bobbins, the standard creel may be placed at the upper rear part of the machine (Fig. 4.19). The yarn is fed from the bobbins (1) to the checking device (2) and then to either the left or right side of the machine where yarn tensioners and/or feeders (3) are situated. This prevents the yarn from coming into collision with the carriage (6) bow. After the yarn guide returns from the extreme left or right position, a length of yarn is released. To permit this change, a yarn length compensator (5) is used. This is typically a spring-loaded thread eye, which enables the yarn to return and form a loop. This is not a perfect solution as the tensile force Fy of the yarn fed from this loop is less than that imparted by the tensioner (3). The creel capacity (the number of package pins) will be at least twice the number of yarn guides, as two or more ends are threaded in one guide to form a plaited fabric. A solution, providing two yarns with a loose twist, is introduced in Fig. 4.20a. The yarn from bobbin (1) goes through bobbin (2), and one yarn balloon turn forms one twist on the yarns. Controlling the length of fed yarn is not easy on this type of knitting machine. Difficulties may arise from the interrupted unwinding of yarn from the packages due to reciprocated knitting, or in the case of intarsia machines, by guides and yarn exchange during the knitting. Fortunately, the majority of flat knitting machine products are patterned fabrics, which are not very sensitive to striping.
4.19 Outline of yarn feeding on a flat knitting machine.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
108
Advances in knitting technology
1 2 3 4 5
4.20 Doubling the yarn with some twisting (a); outline of frictional feeder (b, c).
1 2 3 4 5 6 7 8 9 40 1 2 43X
Another problem is consistency of dimensions in plane shaped or ready to wear products. High quality yarn stress control stabilization (negative feeding system) is a partial solution. Flat knitting machines often use frictional feeders (Fig. 4.12), adapted for changed conditions. The principle is shown in Fig. 4.20b, 4.20c (two aspects). One drum (4) controls all the yarns (3), which are fed from one side of the machine. Similar systems are usually used on each side of the machine. Actually, knitting yarns are pressed towards the drum (4), which decreases yarn tensile force in accordance with the equation (4.6), and yarns that are disengaged slip on it; (5) and (6) are yarn length compensators. An advanced solution is to measure the yarn length consumption in the knitted courses with feedback to the stitch cam position DSCS (Digital Stitch Control System).8 The sensor could be a very light pulley driven by wrapped yarn so that the peripheral speed of the yarn and the pulley is the same. Movement of the pulley is monitored, usually optically without any mechanical contact. The machine’s computer is able to calculate the required yarn length per course by summing up the pre-set length in knitted stitches multiplied by the number of knitted stitches, and does the same with tuck stitches and other structure elements. Predicted and actual yarn length may be compared and differences corrected by adjusting the stitch cams. Another similar approach (i-DSCS) is the intelligent active control of fed yarn length.
© Woodhead Publishing Limited, 2011
4.5
Intelligent yarn delivery systems in weft knitting
109
Future trends
Trends in the development of yarn delivery systems are relatively stable as the main goals remain constant: • Steady production • High fabric quality • Easy processing of material, even in lower priced yarns with imperfections. However, the technology available for the realization of these goals is changing and developing. The contemporary trend is for the use of electronics or computers and the introduction of new systems of drives and sensors. Electric and hydraulic servo motors are now available, enabling both exact and flexible movements in controlled mechanisms. The position of stitch cams and needle bed racking is already controlled by step motors and these drives can dose (measure) the length of yarn, even in jacquard fabrics, which are composed of knitted elements with different yarn consumption. Such computer controlled yarn delivery systems are flexible and widely used, thus increasing production and lowering costs.
4.6
Sources of further information and advice
Several papers offer theoretical analyses of yarn delivery systems, but the majority of publications prefer descriptions of the design and properties of particular systems. Company prospectuses and brochures (for example see References 7 and 8) are important sources of information and the internet is an increasingly important resource. Unfortunately, there are not many monographs dealing with the technological aspects of industrial knitting. One of the best known6 is concerned only marginally with the problems of yarn supply.
4.7
References
1 Araujo M. D. and Smith G. W. 1989. Spirality of Knitted Fabrics, Text. Res. J., 59, 247–256 and 350–356. 2 Gupta B. S. et al., Friction in Textile Materials, Cambridge, Woodhead Publishing, 2008, ISBN 978-1-85573-920-8. 3 Kovar R., Flat knitting technology, Knitting Technology, 2/2002, 6–69, ISSN 09470972. 4 Kovar R., Structure and Properties of Flat Textiles (in Czech), Technical University of Liberec 2003. ISBN 80-7083-676-8. 5 Paepke H. and Paepke J. 1994. ‘Fadenbremsen und Spannungsausgleicher für Textilmaschinen’, Wirkerei- und Strickerei-technik, 44, 7, 591–593. 6 Spencer D. J. 1989. Knitting Technology, Oxford, Pergamon Press, ISBN 0-08035912-4. 7 Prospectuses of Memminger-IRO company from ITMA 2007 Munich. 8 DSCS (Digital Stitch Control System) 2001. Instruction manual of Shima Seiki Company.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
5
1 2 3 4 5 6 7
Advances in warp knitted fabric production Bharat J. GAJJAR, Warp Knits, Delaware, USA Abstract: The chapter begins with a discussion of new structures with ‘woven like’ aesthetics and fabric without stretch. Delaware stitch and modified Delaware stitch fabrics, which offer woven like aesthetics with stretch-free fabric, are defined. Commercial Tricot and Raschel fabrics containing spandex are explained, and a newly developed construction with spandex fabrics that have unique aesthetics is illustrated. The chapter reviews Americana and Modified Americana Tricot, with their unique fabric aesthetics. One of the unique aesthetics is crêpe, which has an unusual visual as well as tactile aesthetics. The chapter also shows knitting of the spun yarn at higher speeds. The final section concerns Milanese fabrics, which have a unique structure where both yarns travel in opposite directions, imparting a unique visual aesthetic. Key words: definitions of warp knitting, warp knitting machines, ‘woven like’ structures, two types of laid in stitch, mattress fabric, spandex warp knits, new structures with spandex, ‘crêpe like’ warp knits, nylon.
5.1
1 2 3 4 5 6 7 8 9 40 1 2 43X
Introduction
A warp knit fabric has a structure made of several warp threads or warps that form similar loops in a course. The different stitches are knitted by changing the sideways motion or shogging movement of the guide bars during knitting. There are three basic types of fabric – woven, weft knit, and warp knit. Woven and warp knit fabrics need a warp to form a fabric and a weft knit needs an end to form a fabric. A woven fabric is formed by interlacing warp ends with filling or weft ends to form courses. Only one end is needed to form a course in weft knit, but many ends are needed to form a course in a warp knit. In the United States, many technicians call weft knit fabrics ‘circular knits,’ while warp knit fabrics are called ‘flat knits’. In reality, both weft and warp knit fabrics can be knitted on circular as well as flat machines. However, most weft knit fabrics are knitted on circular machines, and most warp knit fabrics are made on flat machines.
5.1.1 Cross-sections of woven and weft knit fabrics To understand warp knit fabrics, cross-sections of woven and weft knit fabrics with the same weight (about 3.5 oz/yd2) should be compared. Warp knit yarn manufacturing ensures that these key fabrics cost about the same. Figure 5.1 shows 110 © Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
111
5.1 Cross-sections of woven, weft and warp knits.
cross-sections of woven, weft, and warp knit fabrics weighing 3.5 oz/yd2 and having the same thickness and costing the same. In a cross-section, a woven fabric has two ends, a weft knit has three ends, and a warp knit has four ends. But how can they all cost about the same? This is because in woven fabrics two ends cross, in a weft knit one stitch has three ends in a cross-section, and in warp knit there is one stitch with two loops having four ends in a cross-section. In these fabrics 80 denier yarn is the least expensive to produce, 60 denier yarn is a little more expensive, and 40 denier yarn is even more expensive. A basic weaving loom is the slowest in forming a fabric, weft knit weaving is a little faster than a basic weaving loom and warp knit production is the fastest. If all these factors are combined, the end result is that they all cost about the same.
5.1.2 Wale and course A vertical column of loops knitted by a single needle is called a wale and a horizontal row of wales is called a course. A Jersey structure with a loop and lap diagram is shown on page 112 (Fig. 5.2) with a view of the float side of the fabric (the loop side is on the other side).
5.1.3 Face and back The warp and weft knit face is the loop side and the other side is the float or back side (see the figure above). It is important to be able to identify the face and the back of woven, weft knit and warp knit fabrics. In a woven fabric, the face and back are identical. In a warp knit, either the loop side or the float side could be used as the face of the garment. In 100% nylon or polyester Jersey, the loop side is used as the face of the garment because it has a more attractive appearance. When front bar//
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
112
Advances in knitting technology
1 2 3 4 5 6 7
5.2 Loop and lap diagram of the Jersey stitch.
back bar, nylon//spandex Jersey stitch is made, the float side is used as the face of the garment. Spandex contracts and the fabric eliminates the horizontal lines. When a warp knit fabric is put on a table with the technical face or loop side of the fabric facing up, it is called technically upright. The courses are horizontal and the wales are vertical. The top course is knitted last whereas the bottom course is knitted first. If you cut Jersey fabric two wales wide as shown in Fig. 5.2 you will cut the front bar yarn and the back bar yarn will be in your hand.
5.1.4 Curling propensity 1 2 3 4 5 6 7 8 9 40 1 2 43X
Most warp knit fabrics tend to curl, including the most important type known as Jersey stitch (in the USA) or Locknit stitch (in the UK). If they receive appropriate heat treatment, synthetic warp knit fabrics do not curl. In dyeing, finishing, cutting and sewing garments, it helps to know the face and back of the fabric and its curling propensity. When a greige nylon Jersey stitch fabric is put on a table technically upright (having the loop side up), the top and bottom edges of the fabric will curl upwards or towards the loop side or technical face. However, the side edges will curl under the fabric towards the float or technical backside of the fabric. If nylon Jersey stitch fabric is heat set it will not curl, but if that fabric is laid on the table technically upright and it is pulled sideways on the top edge of the fabric, the fabric will curl towards the loop side. There are some warp knit structures that will not curl in the greige state.
© Woodhead Publishing Limited, 2011
5.2
Advances in warp knitted fabric production
113
Commercial warp knit machines
5.2.1 Comparing sales of warp knits with woven and weft knits The amount of total fabric produced worldwide per year is highest for woven fabrics, second highest for weft knit fabrics, and lowest for warp knit fabrics. The major reason is that spun yarn cannot be incorporated in warp knit at a high speed.
5.2.2 Types of warp knit machine There are four basic types of warp knit machine. They are Tricot, Raschel, Simplex and Milanese. The Tricot and Raschel machines can be either one-bed or two-bed machines. There are three types of needle used in warp knitting. They are shown in the diagram (Fig. 5.3) below. Warp knit machines require a warp to knit. The four basic types of warp knit machine produce six different warp knit machines with various types of needle as shown in Table 5.1. Tricot machines with spring-bearded and compound needles are lighter weight machines and run very fast whereas Raschel machines with latch needles are very heavy and run slowly. Tricot machines with compound needles are faster as the needles are a more recent discovery. Raschel machines with latch needles are slow whereas newer Raschel machines with compound needles are faster but not as fast as Tricot. It is important at this point to compare Tricot with Raschel machines to understand their function properly (see Table 5.2).
5.3 Three types of needle for warp knitting.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
114 1 2 3 4 5
Advances in knitting technology
Table 5.1 Types of warp knitting machine Type of machine
Number of beds Type of needles used
Tricot, flat Raschel, flat Simplex, flat Raschel, flat Milanese, flat Milanese, circular
One One Two Two One One
Spring-bearded needles, compound needles Latch needles, compound needles Spring-bearded needles Latch needles Spring-bearded needles Spring-bearded needles
Table 5.2 Tricot versus Raschel machines
1 2 3 4 5 6 7 8 9 40 1 2 43X
Tricot
Raschel
Spring-bearded needles
Latch needles
Thinner compound needles Heavier compound needles One needle bar One or two needle bars One sinker bar No sinker bar One presser bar (also cut presser No presser bar needed bar) 1–24 guide bars (usually 1–48 guide bars 2 + 04 bars) Width up to 260 inches (168 and 84 Width up to 240 inches (160 inches common) inches common) Gauge 14–36 needles/inch (28 and Gauge 8–64 (needles per 2 inches) 32 gauge common) Speeds up to 1 800 spm (stitches Up to 1 000 spm per min) for spring bearded; 2 500 spm for compound needles Fabric angle 90° 150° angle Lower take-up tension Higher take-up tension Use mostly filament yarn/ Uses filament, textured and spun yarns compound needle could knit spun yarn Links move one course Links move ½ course Knits up to 240 denier hard yarn Knits up to 1 500 denier hard yarn or filament yarn Knits up to 140 denier spandex yarn Knits up to 1 000 denier spandex yarn Less versatile in styling and designing More versatile for fancy pattern work Small and large mills Mostly small mills including garage operators Gauge is needles/inch Gauge is needle/2 inches
5.2.3 Basic commercial warp knit fabrics Among all of the machines, Tricot machines are the most popular in production. Within the Tricot fabric, the king of all stitch construction is Jersey stitch construction.
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
115
The Jersey stitch can be knitted from spun yarn, textured yarn, filament yarn, and spandex yarns. The spun fabric yarn fabrics are not commercially feasible, as they cannot be knitted at high speed. Commercial fabrics are made from filament yarn and spandex yarns only. Within that, filament yarn is the most used, as it is utilized in women’s undergarments. If there is one stitch that dominates the warp knit industry, it is the Jersey stitch. This two-bar warp knit structure is known by many names. It is called Jersey in the USA, Locknit in the United Kingdom and Chaemeuse in Europe. In common usage, Jersey means a knitted fabric. Jersey fabric is a warp knit which is knitted on any single needle bed warp knitting machine (Tricot or Raschel). This fabric is knitted with two fully-threaded guide bars, where the front bar is knitting a three needle float (Silk Float) using closed stitches (2-3, 1-0 or 1-0, 2-3) and the back bar is knitting a two needle float (Cotton Float) also using closed stitches (1-0, 1-2 or 1-2, 1-0). Both the bars, while knitting, are shogging independently in opposite directions. Long float (LF) Jersey or satin, a modified Jersey fabric, is the same as conventional Jersey except that the front bar shoggs four needles instead of three. In the super float Jersey, the front bar shoggs five needles and in the short float Jersey it shoggs two needles. It is very important to remember that in a Jersey stitch construction, the back bar yarn is always sandwiched into the front bar yarn and when one touches the hand of the fabric on both sides, one feels only the front bar yarn. If the front bar contains white yarn and the back bar contains black yarn, the Jersey fabric will look almost white; a little of the back bar yarn can be seen between the wales and the fabric will look slightly colored.
5.2.4 Knitting and finishing Jersey fabric is knitted at about 1 000 stitches per minute (spm) on older machines and at about 2 000 spm on newer, compound needle Tricot machines. Faster machines are being developed. Good filament yarns are knitted on 168-inch wide machines, knitting at about 1 000 to 2 000 racks per end out, which is considered an excellent knitting performance. There are three types of finishing sequence that are used in finishing Jersey and modified Jersey fabrics. They are: • Heat-set, scour and dye. This sequence is preferred when nylon is used by heat-setting first and the final yield of a fabric is obtained. However, the disadvantage of this sequence is that it fixes the stains and dirt that are picked up during knitting. • Scour, heat-set and dye. This sequence is preferred for polyester. It eliminates the impurities in the fabric, offers greater bulk and contains a bleaching step that removes yellowing caused during heat-setting, but this finishing sequence is expensive as it requires pin tentering twice. © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
116 1 2 3 4
Advances in knitting technology
Table 5.3 Jersey and modified Jersey stitches Fabric No. Stitch
Front bar// back bar Aesthetics
1. 2.
Jersey Satin or Long Float Jersey Slipper Satin or
2-3, 1-0//1-0, 1-2 3-4, 1-0//1-0, 1-2
Widely used; classic Tricot fabric Heavier/bulkier than Jersey
4–5, 1-0//1-0, 1-2
1-2, 1-0//1-0, 1-2
11.
Double Tricot or Short Float Jersey Open Jersey Del Jersey Mixed Jersey Open Long Float Jersey Open Super Long Float Jersey Mixed Long Float Jersey Long Float Del Jersey
Heavier/bulkier than Super Long Float Jersey Long Float Jersey Lighter than Jersey
12.
Laid-in Jersey
With all above stitches
3.
4. 5. 6. 7. 8. 9. 10.
3-2, 0-1//0-1, 2-1 3-2, 0-1//1-0, 1-2 3-2, 1-0//1-0, 2-1 4-3, 0-1//0-1, 2-1 5-4, 0-1//0-1, 2-1 3-4, 0-1//0-1, 1-2 4-3, 0-1//1-0, 1-2
Higher luster than Jersey Less distortion than Jersey Drier hand than Jersey Higher luster than Long Float Jersey Higher luster than Super Long Float Jersey Drier hand than Jersey Higher recovery than Long Float Jersey Lower stretch; heavier/bulkier than Jersey
• Scour, heat-set and dye. This sequence is preferred for polyester. This finishing sequence is the most economical as it combines scouring and dyeing. However, there are two problems associated with it. One is that it sometimes imparts rope marks, a defect in a fabric. The other is that heat yellowing affects the final color of the fabric. 1 2 3 4 5 6 7 8 9 40 1 2 43X
Plain Jersey is the most important structure. However, if you would like to look into modified Jerseys, see Table 5.3 above.
5.3
Delaware stitch and modified Delaware stitch Tricot fabrics
5.3.1 Introduction Delaware stitch is a very popular warp knit structure. It has a ‘woven like’ appearance, low stretch, and is used in men’s and women’s outer garments. It is extensively used in women’s lingerie and has captured 50% of the mattress fabric market using filament polyester yarn. Delaware stitch was developed by the author, and DuPont DeNemours and Co. introduced it with the T472 nylon yarn and used it extensively in Qiana® fabric. This fabric has been in high demand
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
117
Table 5.4 Delaware and modified Delaware stitches Fabric No. Stitch name 1. 2. 3.
4. 5. 6. 7. 8. 9. 10. 11. 12. 13.
Front bar//back bar
Delaware stitch (DS) 2-3, 1-0//1-0, 0-1 Open Delaware 3-2, 0-1//0-1, 1-0 stitch 2-3, 0-1//1-0, 0-1 Mixed Delaware stitch or 3-2, 1-0//0-1, 1-0 Long Float (LF) 3-4, 1-0//1-0, 0-1 Delaware stitch Open LF Delaware 4-3, 0-1//0-1, 1-0 Mixed LF Delaware Short Float (SF) Delaware Satin Delaware Atlas Delaware Double Needle Delaware Double Needle SF Delaware Double Needle LF Delaware Laid-in Delawarea
4-3, 1-0//0-1, 1-0 1-2, 1-0//1-0, 0-1
Similar aesthetics Woven More luster than DS Drier hand than DS
Woven satin Little more luster than LFDS Drier than number 5 Less luster than DS
4-5, 1-0//1-0, 0-1 High luster 0-1, 2-3/5-4, 3-2//1-0, 0-1 New aesthetics 4-2, 0-2//1-0, 0-1 Heavier than DS 3-1, 0-2//1-0, 0-1 5-3, 0-2//1-0, 0-1 With all above stitches
Lighter weight than number 8 Heavier weight than number 8 Higher drape and heavier than DS
Note: aCould be knitted with the middle bar having one needle (0-0, 1-1), two needle (0-0, 2-2), three needle (0-0, 3-3), four needle (0-0, 4-4) or five needle (0-0, 5-5) Laid-in stitches, e.g. three needle Laid-in Delaware stitch 2-3, 1-0//0-0, 3-3//1-0, 0-1.
over the past three decades and the Delaware stitch warp knit structure is currently used around the world in many applications. Delaware stitch offers a warp knit fabric produced with the front bar knitting a three-needle float stitch (2-3, 1-0) and the back bar knitting a chain stitch (1-0, 0-1). Long Float Delaware stitch fabrics use a four needle float in the front bar and the Short Float Delaware stitch fabrics use a two needle float in the front bar. The Delaware stitch fabrics also use open stitches. Other modified Delaware stitches are in Table 5.4 above.
5.3.2 Advantages of Delaware stitch The Delaware stitch-type fabrics, compared to the Jersey stitch constructions, offer woven like low stretch, greater liveliness and new aesthetics including satintype high luster. They are about 10% lighter at a given stitch density, meaning lower cost, wider fabric width and lower fabric weight. They also offer greater fabric stability, higher air permeability through the open knit structure and greater rigidity.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
118 1 2 3 4 5 6 7 8 9
Advances in knitting technology
In a Jersey stitch fabric, only the loop side is used as the face of a garment and not the float side because the float threads of the Jersey stitch are not parallel and do not have a uniform look. On the other hand, the float threads of a Delaware stitch fabric are parallel, making its float side attractive; consequently, it can be used as the face of a garment. However, the float side is preferred and most widely used. In a Jersey-type of stitch construction, the back bar is always sandwiched in between the front bar yarns, so that the back bar yarn cannot be seen. Unlike the Jersey stitch, in the Delaware stitch fabric the front bar yarn appears on the float or back of the fabric, and the front and back bar yarns (about 50/50) appear on the loop side or the front of the fabric. In other words, if a black yarn is used on the front bar and white yarn is used on the back bar, in a Jersey stitch fabric the black color will be on both sides, whereas in a Delaware stitch fabric, the loop side will be predominantly white with a little black color and the float side will be completely black. Thus, it will be a two-colored fabric (see Table 5.5.)
5.3.3 Common quality problems There are three basic concerns or fabric defects in Delaware stitch fabrics. These are: an uneven fuzz area created during knitting, wale shifting or grouping that develop during knitting and/or finishing, and pickiness or stitch distortion of a fabric. Wale shifting or wale grouping is a typical problem in Delaware stitch fabrics, which is imparted by certain conditions and caused by an unstable knit structure. This problem is peculiar to the Delaware stitch structure. A wale shift-free Delaware stitch fabric was first developed in the Textile Research Laboratory of DuPont deNemours and Company. Wale shifting is defined as a fabric defect where some areas of the fabric encounter uneven shifting and grouping. When it occurs in a finished fabric, the fabric is unacceptable. Make sure wale shifting is avoided. Table 5.5 Some examples of Delaware stitch fabrics (32 gauge Tricot)
1 2 3 4 5 6 7 8 9 40 1 2 43X
Finished
Runners Yarn Quality FB//BB Weight Count Fabric FB//BB Stitch (inch) (inch) (oz/yd2) 1. 20-10 nylon// 2-3, 1-0// same 1-0, 0-1 2. 40-12 nylon// 3-2, 0-1// 20-10 nylon 0-1, 1-0 3. 40-12 nylon// 4-3, 0-1// 20-10 nylon 0-1, 1-0 4. 40-12 nylon// 4-3, 0-1// same 0-1, 1-0
Thick- ness BS Bulk (inch) (cm3/g)
6
50//30
1.3
38 × 82 0.010
5.76
7
57//32
2.2
36 × 76 0.017
5.79
6
70//33
2.7
38 × 82 0.018
4.99
7
75//33½ 3.4
40 × 84 0.026
5.73
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
119
A number of ways in which to stabilize or to obtain a wale shift-free Delaware stitch fabric are the following. Tighter fabrics are better than the open fabrics. The more courses per inch the better the stability will be. Heavier yarn denier and/or finer machine gauge is better than a lighter yarn denier and coarser machine gauge. Higher friction in the yarns such as mixed shrinkage yarn is better than smoother, regular yarns. Textured or spun yarn on only one of the bars will offer wale shift-free fabrics. A longer float in a fabric offers better stability than the shorter float. Relaxed heat setting (7 to 10% overfeed) and drying offers wale shift-free fabrics. Widthwise stretching of the fabric during heat setting or drying causes wale shifting. Laid-in stitches offer wale shift-free fabrics. Double needle fabrics offer wale shift-free fabrics. Two needle float or short float fabrics do not encounter wale shifting, but the appearance of this fabric is not as attractive. Atlas stitch offers better shift resistance fabric. Note that the double needle and laid-in stitches offer wale shift-free fabrics, but also heavier fabrics, less liveliness, and increased stiffness than the Delaware stitch fabrics.
5.3.4 Two types of laid-in Delaware stitch There are two basic types of laid-in Delaware stitch fabrics. The first, type A, is the laid-in stitch in the middle bar, for example 2-0, 1-0//0-0, 3-3//1-0, 0-1 and the other, type B, is the laid-in stitch on the back bar, for example 2-3, 1-0//1-0, 0-1//0-0, 2-2. The laid-in Delaware stitch fabric, having yarn layout with spandex in the middle bar (T472/spandex/T472), makes an attractive fabric. Heavyweight outerwear (60 denier) Delaware stitch fabrics have been developed. Heavyweight Delaware stitch fabrics do not encounter wale shifting.
5.3.5 Mattress fabric In 1990 it was reported that in the USA 50% of mattress fabrics are woven and 50% are of 70-34//40-14 polyester Delaware stitch fabrics. Many mattresses use long float Delaware stitch fabric (3-4, 1-0//1-0, 0-1).
5.4
Tricot and Raschel containing spandex
5.4.1 Introduction After filament, the most important fabrics are Tricot Raschel material with spandex yarn. This unique fabric, with its new visual and tactile quality and new dimension in fabric properties (high stretch, power, recovery and aesthetics) made it possible to use Tricot fabrics in new areas, such as swimwear, bras, panties, leotards, sportswear and many such similar uses, and now it has even been introduced into medical applications. Spandex yarn requires special handling in
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
120 1 2 3 4 5 6
Advances in knitting technology
warping, knitting and finishing; therefore, fabric manufacturers should make sure they provide their consumers with fabrics that have proper stretch, recovery and dimensional stability, and garment manufacturers should provide for the fit and comfort of the garment. The word ‘spandex’ is a generic term in the USA and in many other countries. In continental Europe, the generic term is ‘elastane.’
5.4.2 Yarn used in Tricot The main commercial spandex yarns are Lycra®, Dorlastan®, Glospan®, Fujibo®, and Roica®. Typical spandex-containing Tricot mostly uses 40 denier yarn with about 3 denier per filament (dpf) untextured nylon yarn on the front bar and 40 denier spandex yarn on the back bar. Only bare (uncovered) spandex yarn is used in Tricot knitting. The yarn deniers used are 20, 40, 55, and 70 denier (22, 44, 61, and 78 dtex). Spandex yarn must be used in combination with hard yarn or filament yarn. The spandex yarn is used on the back bar and the hard yarn is used on the front or top bar of the Tricot machine. In this way the spandex yarn is sandwiched into the front bar yarn. Thus, the hard yarn protects the spandex yarn and it does not come into contact with the human skin during wear. Yarn suppliers offer the spandex yarn on spun tubes, rewound tubes and on beams (42 inch and 21 inch). In Tricot knitting, only the 164 inch or 84 inch wide Tricot machines are used, mostly with a 28 and 32 gauge and sometimes a 36 gauge (gauge = needles per inch).
5.4.3 Stitches used in Tricot fabrics containing spandex In the Tricot warp knit industry there are two basic stitch constructions that dominate the trade. As mentioned earlier, the ‘king’ of all stitches is the Jersey stitch. The second most popular is the long float Jersey stitch. 1 2 3 4 5 6 7 8 9 40 1 2 43X
5.4.4 Nylon/Spandex (Lycra) versus 100% Nylon Jersey It is interesting to note Nylon//Spandex F//BB and 100% Nylon Jersey are quite unique and different. (DuPont Lycra is also known as spandex.) The comparison is shown in Table 5.6.
5.5
Key Raschel fabrics containing spandex
5.5.1 Introduction Warp knit Raschel fabrics containing spandex yarn are a very important segment of the warp knit industry. In the USA, Tricot consumes about 11% of spandex,
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
121
Table 5.6 Warp knit Jersey Tricot with and without Lycra®
Nylon//Lycra®
100% nylon (Jersey)
Yarn: Front bar Back bar Stitch: Jersey Quality (inch) Runners (inch) Yarn content Machine width (inch) Gauge (npi)
40-13 T865B nylon 40d Lycra® T-126 FB 2-3, 1–0 BB 1-0, 1-2 7½ 58//24 79.5% nylon 20.5% Lycra® 164 28
40-13 T865AB nylon 40-13 T865 AB nylon FB 2-3, 1-0 BB 1-0, 1-2 7 58//43 100% nylon 164 28
78 5.2
110 2.2
66 × 100 0.029 4.19
55 × 50 0.011 2.90
140 × 130
10 × 70
57 none
– –
0.13 × 0.34
–
4.5/5.0 4.0/5.0 High
3.9/5.0 3.2/5.0 Low
Finished fabrics Width (inch) Weight (oz/yd2) Count W × C (inch) Thickness (inch) Bulk (cm3/g) Hand Stretch % Length × width Wet sag recovery Length direction (%) Seam pull-out Power (lb/inch) Instron – 12 lb (unload at 50%) length × width RTPT-fuzz and pill 30 120 Edge curling
RTPT = random tumble pill tester
Raschel 22%, weft knits 6–10%, woven 2%, and the remaining spandex is used in other types of fabrics. Spandex-containing Raschel is unique. It offers three basic fabric properties not available from any other fiber except rubber, but rubber yarns cannot be spun with either very light denier or high power. The three basic fabric properties are high stretch, recovery, and power.
5.5.2 Knitting machines To understand warp knit Raschel machines, it will be helpful to compare them with warp knit Tricot machines. The following are the 12 basic differences.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
122 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 9 40 1 2 43X
Advances in knitting technology
• Raschel machines are heavier and produce heavier fabrics. • Older Raschel machines have latch needles with knitting speeds of 800–900 spm whereas the older Tricot machines have spring bearded needles with knitting speeds of 800 to 2 000 spm. • New Raschel and Tricot machines use compound needles, with Raschel machines knitting more than 1 300 spm and Tricot machines knitting more than 2 000 spm. • Raschel machines use two 50-inch beams for 100-inch wide machines, or four 50-inch beams for 200-inch wide machines, six 21-inch or three 42-inch beams for 130-inch wide machines. Tricot machines use four 42-inch beams for 168-inch wide machines. • In Raschel machines the gauge of the machines is measured in needles per two inches and common gauges are 64 gauge (32 npi) and 56 gauge (28 npi). On the other hand, in Tricot, gauge equals needles per inch, and common gauges are 28, 32, and 36 (40 gauge machines have been developed but are not used widely). • The fabric angle to the warp on Raschel machines is 160° take-up whereas in Tricot machines the angle is 90° take-up. This is the reason why Raschel stitch constructions such as heavy Gentlissimo and Power Net cannot be knitted on Tricot machines. • On Raschel machines, fabric take-up tension is high, whereas on Tricot machines take-up tension is lower. • Raschel machines with latch and compound needles do not need a presser bar. Since the needles are heavier and bigger, Raschel machines can use spun yarn or heavier spandex yarn, whereas the Tricot machines with spring bearded needles need a presser bar, and since needles are smaller, knitting of spun yarn is more critical. • Raschel machines knit up to 1 500 denier yarn, whereas Tricot machines knit up to 240 denier hard yarn (for spandex 1 000 versus 140 denier respectively). • In Raschel machines, the links move half a course, whereas in Tricot machines the links move one course. Because of this, lap notation of Raschel is written 2-0, 2-4 for the back bar Jersey stitch. The same lap notation for Tricot is written 1-0, 1-2. • Raschel machines are more versatile and are used for fancy pattern work, whereas Tricot machines are less versatile in styling and designing. • Raschel mills are smaller whereas Tricot mills are larger and more likely to be integrated mills.
5.5.3 Stitches used in Raschel fabrics containing spandex There are hundreds of stitch constructions available, and many stitches are used in the Raschel industry, but within spandex-containing Raschel fabrics only four stitch constructions are used. They are Gentlissimo (1st bar 2-0, 2-2, 4-6, 2-2, 2nd
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
123
bar 2-2, 2-0, 2-2, 2-4, 3rd bar 2-2, 0-0, 2-2, 4-4) (in Europe it is known as Sleeknit), Techsheen (1st bar 2-0, 0-2, 2-4, 4-2, 2nd bar 2-2, 0-0, 4-4, 0-0), Power Net (1st bar 4-2, 2-4, 2-0, 2-4, 4-2, 4-6, 2nd bar 2-4, 4-2, 4-6, 4-2, 2-4, 2-0, 3rd bar 2-2, 0-0, 2-2, 0-0, 2-2, 0-0, 4th bar 0-0, 2-2, 0-0, 2-2, 0-0, 2-2) and Jersey (Locknit). When nylon//spandex Tricot Jersey (2-3, 1-0//1-0, 1-2) fabrics became very successful, the industry started looking for a suitable new structure for nylon// spandex Raschel. Jersey stitch could be produced on Raschel machines, but the industry required two major improvements: • more power in the fabric; and • lower cost fabric, using heavier denier spandex yarn. These improvements were obtained when Gentlissimo stitch for Raschel was developed. It replaced 40 denier spandex yarn and knit stitch of the Jersey stitch with 140 denier spandex yarn and laid-in stitch.
5.5.4 Face or back The loop side of warp knit fabric is called the technical face and the float side of the fabric is called the technical back. The technical face of 100 percent nylon Jersey fabric is used as the face of the garment. But in all the spandex-containing Tricot and Raschel fabrics, the technical back of the fabric is used as the face of the garment.
5.5.5 Summary of stitches, yarns and end-uses Usually nylon yarns are used on the front (top or first bar) and middle (or second) bar, and spandex yarns are used on the back or the third bar in Raschel knit fabrics.
5.5.6 Fabric testing The key fabric tests in evaluating spandex-containing Raschel fabrics are: (1) weight, (2) construction (wales x courses), (3) yield (percent elastomer), (4) width, (5) tensile properties (power/stretch/set), (6) shrinkage and growth, (7) flex life (spandex pull out and slippage), (8) whiteness retention, (9) heat-set efficiency, (10) molding performance, (11) dyeability and fastness, (12) uniformity and (13) chlorine resistance or durability. Every type of garment has its own needs that have to be satisfied. For example, swimwear and panty fabrics need more stretch and to be lightweight whereas foundation garments need more power and to be a heavier weight.
5.5.7 Quality control Spandex is an expensive yarn compared to nylon, and a very sensitive yarn for a mill to work with. In addition, the mill has to be set to a very high yarn tension. Therefore,
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
124 1 2 3 4 5 6 7 8
Advances in knitting technology
it is very important to have the proper warping, knitting and finishing conditions, and once the mill has defined the conditions they have to be implemented without much variation. As new machines are computerized, they are a great asset in quality control. When a mill is developing quality fabrics it should avoid the following fabric problems: streaks/bands, poor dimensional stability (not meeting the required growth and shrinkage), moiré, excessive fabric edge curling, dye spots, spandex degradation, dye blotches, rope marks, shading and unevenness, poor wet fastness (causing fabric to lose its color when wet), fabric creases and cracks, width and weight variations, uneven power and stretch properties, and excessive bagginess. To maintain good fabric quality, Raschel machines should be kept clean and the atmosphere in the knitting area should be maintained at 70–75°F (21–24°C) and 50–65% relative humidity (RH).
5.5.8 Guidelines Swimwear and panty markets are very important for the spandex-containing Tricot fabrics. DuPont deNemours & Co. has established its own guideline for the nylon//Lycra® containing warp knit fabrics. These are the minimum required properties to satisfy the customers; however, for nylon//Lycra® Jersey swimwear and underwear, 18–20% Lycra® is recommended. The guidelines are outlined in Table 5.7 below.
5.6
Newly developed constructions with spandex
5.6.1 Introduction These are newer constructions and they have limited use. They will expand in due course and as new end uses are developed. Table 5.7 DuPont’s guidelines for nylon//Lycra®-containing warp knit fabrics
2 3 4 5 6 7 8 9 40 1 2 43X
Test parameter
Warp knit minimum acceptable test value
Swimwear and leotard guidelines • Wet sag recovery • Elongation (wale direction) • Seam pull-out • Lycra® content
≥ 40% ≥ 100% Zero pull-out 0.6 oz/yd2
Panty guidelines • Elongation (length × width) • Power (lb/inch) 45% elongation for return curve (3lb) • Seam pull-out 600 cycles • Lycra®
40 × 30% 0.1 minimum Zero pull-out or pull back ≥10%
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
125
5.6.2 Del-Atlas stitch Del-Atlas stitch is not a Jersey stitch. Jersey stitch is a two-course repeat whereas all Atlas stitches are at least a three-course repeat, But in this study, four-course Atlas stitch was selected. Atlas stitch can be knitted using only one bar, but DelAtlas must have two bars. Del-Atlas has at least a four-course repeat on the front bar and at least a two-course repeat on the back bar. Note that the front bar with nylon yarn has only open stitches and the back bar with spandex yarn has only closed stitches. The improved chlorine of the Del-Atlas durability was confirmed in a break test (failure is Lycra® spandex break). The test also showed greater resistance to power loss. One obvious reason is that this knit structure allows the spandex yarn to be free and does not cut at a crossover point such as Jersey does.
5.6.3 Kuper or twill stitch In the front bar the double needle stitch goes from left to right and goes two needle stitches in the same direction. It then goes two needle floats to the right . . . at the same time, the back bar yarn knits one needle stitch and goes two needle floats in the opposite direction (to the left). In the USA, this stitch is known as the Kuper stitch, but in Europe it is known as the twill stitch. This fabric is a swim- and sportswear-type fabric. This stitch offers a heavier fabric compared to Jersey and Gentlissimo without increasing stitch density, and it also offers a wider fabric. Kuper stitch offers 90-inch fabric, whereas Gentlissimo offers 60-inch fabric. In reality, the Kuper stitch is a double needle long float stitch. There are two kinds of double needle stitch: open and closed. Open stitch fabric is more commonly used.
5.6.4 Double needle Delaware stitch The front bar knits double needle open or closed stitches and the back bar knits spandex using the chain or pillar stitch. This fabric offers a suitable fabric for women’s outerwear. It has only length directional stretch and could be used where one-directional stretch is needed, as in a shoe upper or in medical uses.
5.6.5 Laid-in Delaware stitch Three or four needle float stitch is knitted in the front bar, laid-in stitch in the middle bar and chain stitch on the back bar. This is used in women’s outerwear fabrics.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
126 1 2 3 4 5 6 7
Advances in knitting technology
5.6.6 Laid-in Jersey stitch The front and middle bar knit Jersey stitch and the back bar knits laid-in stitch. The laid-in yarn could use 1-1, 0-0 or otherwise two or more needle float stitch, e.g. 2-2, 0-0, or 3-3, 0-0, which imparts more weight as well as more stretch. This fabric will have a very small percentage of spandex yarn, as the spandex uses one needle laid-in.
5.7
Americana and modified Americana Tricots
5.7.1 Introduction The Americana stitch and its family of fabric structures were developed by using a basic knit-lay technique similar to that found in weft knit interlock structures. In Americana stitch structure knitting, two fully threaded warps or bars create one bar consisting of only one stitch with one loop per needle. In contrast, knitting two bar Jersey fabric produces one stitch with two loops per needle. Americana stitches are disclosed in the author’s patent Method of Warp Knitting, US Patent 4 802 346, 7 February 1989, assignee E.I. DuPont deNemours & Co., and patent Method of Warp Knitting, US Patent 5 029 457, 11 December 1991, assignee E.I. DuPont de Nemours & Co. The DuPont Co. freely gave this technology to the warp knit industry as a good-will gesture. In 1990, DuPont & Co. introduced Americana stitch technology to selected warp knit customers in the US. Included were a sample book and the technology to develop textured and spun filaments, and Lycra® spandex fabrics created with Americana stitch constructions. Americana stitch, with the knit-lay concepts, provides knitters with a family of stitch construction fabrics.
5.7.2 Definition of Americana stitch 1 2 3 4 5 6 7 8 9 40 1 2 43X
The Americana stitch employs two fully threaded warps or bars to knit a one bar fabric. By using knit-lay on the front bar and lay-knit on the back bar, each needle produces one stitch with one loop. Using more than two fully or partially threaded bars produces fabric with a two-course repeat pattern of alternating first and second bar yarns. The fabric is prepared by interlocking the first and second yarns using a combination of Knit and Laid-in stitches in an alternating fashion. In course number one, the front bar knits and the back lays in. In course number two, the front bar lays in and the back bar knits. The fabric construction is as follows: Americana stitch: nylon//spandex Tricot, 28 gauge, FB and/or MB 40-13 T860 bright nylon//BB 40 denier Lycra® (see Table 5.8).
5.7.3 Two basic types of Americana stitch The two bar Americana structure produces two basic types of stitch. The Americana stitch is produced when bars go in opposite directions, and crêpe © Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
127
Table 5.8 Stitch construction Fabric Front bar Middle bar Back bar no.
Quality (inch)
Runners FB//MB//BB
A B C D
7½ 6½ 6½ 7½
37½//37½//27 35//35//3 37//37//26 58//24
1-0, 3-3 1-0, 3-3 2-3, 0-0 2-3, 1-0
3-3, 1-0 3-3, 1-0 3-3, 1-0 –
1-0, 1-2 0-0, 3-3 1-0, 1-2 1-0, 1-2
Americana stitch is produced when both bars go in the same direction. See Fig. 5.4 below.
5.7.4 Americana knit structure Americana imparts unique fabric structures. A commercial Jersey stitch fabric, for example, uses two fully threaded warps that offer back bar yarn sandwiched between the front bar yarns. The counterpart Americana stitch fabric puts all front bar yarn on the float or technical back of the fabric, and front and back bar yarns alternatively on the loop side or technical face of the fabric.
5.7.5 Splitting problem Commercial one bar fabrics (e.g. 2-3, 1-0) have a splitting problem, which makes them unusable. Fabrics made with a similar stitch construction have the same splitting problem. Weft knit fabrics such as nylon stockings will run, but will not split. The two sides will stay together. Because of this splitting problem, one bar fabrics are not commercially acceptable. Instead, two bar fabrics are commonly used in developing warp knit fabrics. The two bar Americana stitch can produce a stable one bar fabric providing 100% filament smooth yarn (such as 30-10 nylon) or textured yarn and is tightly knitted.
5.7.6 Americana stitch containing spandex Commercial nylon//spandex Jersey fabrics are ideal for women’s swimwear and sportswear and many other applications. There are two basic Americana stitch
5.4 Two types of basic Americana stitch.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
128 1 2 3 4 5 6 7
Advances in knitting technology
fabrics that contain spandex, namely Americana and crêpe Americana. Moreover, there are two ways of developing spandex-containing fabrics. Americana stitch with nylon on front bar and middle bar, and spandex on the back bar, creates a three bar fabric. Spandex can also be used on the middle bar with nylon on the front and back bars.
5.7.7 Advantages of Americana stitch Americana stitch offers many advantages: a family of new knit structures and new visual and tactile fabric aesthetics; lighter weight, lower cost fabrics with lower cover and high air permeability; newer, less expensive surface interest fabrics; new tools for styling and designing; better fabric uniformity compared with Jersey; new spun-containing fabrics with improved knitting performance and the ability to blend two different yarns in a fabric without adding any weight (e.g. nylon and polyester.)
5.7.8 Family of Americana stitches Americana stitch is a basic stitch construction that has led to a family of new stitch constructions. Table 5.9 identifies seventeen basic Americana stitch constructions. Knit stitch (e.g. 1-2, 1-0 or 1-0, 1-2) could be used on the front or back of Americana stitches. Laid-in stitch (e.g. 0-0, 3-3) could also be incorporated on the back bar. All the basic Americana stitches can be made with the third bar in front of the back bar with 1-0, 1-2 or 1-2, 1-0 or similar knit stitch constructions (see Table 5.9). As mentioned, the Americana stitch offers two basic structures: Americana stitch, which has a regular flat appearance, and crêpe Americana, which, as its name suggests, looks crêpey and is textured.
1 2 3 4 5 6 7 8 9 40 1 2 43X
5.7.9 Modified Americana stitch Modified Americana stitches are identified as three bar Americana, four bar Americana, and five bar Americana, etc. A three bar Americana stitch requires three bars that knit a three-course repetition. In the course, the front bar knits and the middle and back bars lay in. In the second course, the middle bar knits and the front and back bars lay in. In the third course, the back bar knits and the front and middle bars lay in. Due to this, the three-course repetition with three fully threaded bars will have only one loop per stitch. Four bar Americana stitch has four courses in a repeat and four bars per repeat. In the first course, the front or first bar will knit, in the second course the second bar will knit, in the third course the third bar will knit and in the fourth course only, the back or the fourth bar will knit. All the other bars will lay in. Figure 5.5 is a lap diagram of the three bar modified Americana stitch.
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
129
Table 5.9 Basic Americana stitches
Stitch notations
Fabric Stitch name No.
Front bar
Back bar
1 Americana 3-3, 1-0 1-0, 3-3 2 Satin or Long Float Americana 4-4, 1-0 1-0, 4-4 3 Slipper Satin or Super Long Float Americana 5-5, 1-0 1-0, 5-5 4 Short Float Americana 2-2, 1-0 1-0, 2-2 5 Mixed Float Americana 4-4, 1-0 1-0, 2-2 6 Open Americana 3-3, 0-1 0-1, 3-3 7 Open Long Float Americana 4-4, 0-1 0-1, 4-4 8 Mixed Americana 3-3, 1-0 0-1, 3-3 9 Crêpe Americana 3-3, 1-0 2-3, 0-0 10 Long Float Crêpe Americana 4-4, 1-0 3-4, 0-0 11 Double Needle Americana 2-0, 4-4 4-4, 2-0 12 Open Double Needle Americana 0-2, 4-4 4-4, 0-2 13 Open Triple Needle Americana 0-3, 5-5 5-5, 0-3 14 Atlas Americana 0-1, 1-1, 2-3, 4-4, 5-4 5-5, 4-3, 3-3, 2-1, 0-1 15 Crêpe Atlas Americana 0-1, 1-1, 2-3, 4-4, 5-4 0-0, 1-2, 2-2, 3-4, 5-5 16 3 Bars Americana FB//MB//BB 2-3, 2-2, 1-0, 1-1//1-1, 1-2, 1-1, 1-0//1-0, 1-1, 1-2, 1-1 17 4 Course Americana FB//BB 1-1, 1-0, 2-2, 2-3//2-1, 3-3, 1-2, 0-0
5.5 Lap diagram of modified Americana stitch.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
130 1 2 3 4 5 6 7 8 9 10
Advances in knitting technology
Nylon can be used on the first three bars of the above structure and spandex on the fourth bar knitting regular 1-2, 1-0.
5.8
Surface interest fabrics
5.8.1 Crêpe Tricot The dictionary defines crêpe fabric as a lightweight fabric characterized by a crinkled surface obtained by the use of (1) hard-twist filling yarns (women’s wear fabrics), (2) chemical treatment, (3) crêpe weaves or (4) embossing (calendaring). Woven crêpe is made by high twist yarn, but high twist yarn cannot be used in warp knit production, so the crêpe structure has to be developed by other methods. Some textured yarns do offer crêpe-like aesthetics; however, if a textured 40-13 nylon is used, and a Jersey stitch Tricot knitted, it will not have a crêpe aesthetic. The Tricot industry has had a great need for economically feasible surface interest and/or crêpe aesthetics in lightweight lingerie and/or for women’s outerwear applications.
5.8.2 Ten key elements for developing good crêpe in Tricot
1 2 3 4 5 6 7 8 9 40 1 2 43X
• Evenly and randomly distorted stitches. • Crêpe surface with randomly uniform pebbles. • Crimps per inch (frequency) coinciding with the stitch length, e.g. match crimp/inch with knit quality and runner length (loop needs to be distorted). • Crêpe depth and uniformity of crêpe surface controlled by preferred knit construction (3-4, 1-0//1-0, 1-2 a Long Float Jersey stitch) and knit quality (7 to 9 inches), which depends on yarn shrinkage. • Loop side or technical face of the fabric used as the face. • Stability of the crêpe surface. • Knowledge of yarn’s heat-setting temperature (6 versus 66 nylon yarn). • Low tension at width frame of pin tenter is required. • Low water set in beam pressure setting is required to maintain fabric crimp. • For many fabrics, tumble steam is required for optimum crêpe.
5.8.3 Crepeset® Crepeset® is a crimped nylon monofil produced in a patented toothed-wheel crimp process. The Crepeset® fabric is a soft nylon crêpe Tricot fabric, suitable for lingerie. It is supple with a subtle crêpe appearance. The crimped 30-1 yarn has a low residual crimp force, which requires tumble steam for good crêpe. These yarns are not antistatic. The Crepeset® fabric uses 67% regular yarn and 33% Crepeset® yarn. Crepeset® fabric is produced as follows:
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
131
• FB 30-10 nylon • BB 30-1 Crepeset® yarn • Preferred stitch: Long float Jersey Which is: • FB 3-4, 1-0 • BB 1-0, 1-2
5.8.4 Knit-de-knit crêpe Knit-de-knit crêpe yarn offers very attractive crêpe, but these fabrics have uniformity problems. This fabric cannot be heat-set and therefore also has shrinkage problems. All knit-de-knit fabrics must be tumbled to achieve optimum crêpe. The synthetic yarn 30-1 is knitted and de-knitted. This 30-1 monofilament yarn is used on the back bar whereas 30-10 yarn is used on the front bar and knitted with Long Float Jersey stitch (FB 3-4, 1-0//BB 1-0, 1-2). At present, Knit-de-knit yarn is more expensive than gear crimp yarn.
5.8.5 Textured or surface interest warp knits There are many different types of crêpe structure available but the widely used structures are described above. There are two basic weight fabrics: first, lighter weight Tricot fabrics consisting of 20, 30 and 40 denier textured nylon or polyester yarns, and second, heavier fabrics prepared from 60, 70, or 80 denier textured yarns knitted on a Tricot or Raschel machine. Mills usually buy textured yarns from converters and prepare the beams in their own mills. There are three basic types of warp knit fabric. They are: 1) 100% textured FB textured yarns BB textured yarns 2) Bar-on-bar FB textured yarns BB regular hard yarns or filament yarn 3) Bar-on-bar (second type) FB regular hard yarns BB textured yarns For swimwear, the ideal fabric is nylon//spandex Jersey, but it has limited wear life, owing to the low chlorine durability of the spandex yarn in swimming pools. Swimmers prefer swimsuits made from 100% textured nylon fabrics, because they last longer. However, they are not as aesthetically attractive as nylon// spandex fabrics.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
132 1 2 3 4 5 6 7 8
Advances in knitting technology
Lower-stretch fabrics using the bar-on-bar textured nylon//nylon Jersey are used in women’s dress wear and these fabrics, along with bar-on-bar nylon// textured nylon fabrics, can be used for lingerie applications.
5.8.6 Simplex machines These are two bed flat warp knit machines with two needle bars containing back to back spring-bearded needles. The machines have two guide bars, which makes them much slower than Tricot machines. So it costs more and it also produces a double faced fabric that is thicker. It is used mainly in hand gloves. It is available in widths of 84 inches, 93 inches, 138 inches, and 168 inches, while gauges range from 28 to 32 needles per inch in each needle bed.
5.9
Milanese fabrics
5.9.1 Introduction In the warp knit industry, Milanese fabrics are in a class of their own. They are high quality and expensive fabrics. The basic structure of the Milanese fabric cannot be produced on the conventional Tricot or Raschel warp knit machines. There are very few Milanese machines in the USA, but in Europe there are more. The main reason Milanese fabrics are used is because they offer better uniformity to non-uniform yarns such as silk and cotton than the counterpart Tricot or Raschel fabrics. Milanese machines can be flat or circular.
5.9.2 Milanese structure
2 3 4 5 6 7 8 9 40 1 2 43X
In order to understand Milanese fabrics, the workings of the Tricot machine should be explained. In Tricot, a warp end could knit on the first needle course and on the second course; the end could knit on the same needle or a second or third needle or up to the eighth needle. After knitting one repeat of the stitch, the machine keeps repeating the same stitch. However, it must be understood that a warp end must go back and forth between the eight needles, mostly between the first and the third needles. In Milanese, one end of the warp knit knits one needle making the first course. In the second course, it knits the needle to its right, in the third course it knits the third needle, and the end continually keeps going to the right. If the front bar goes in the right direction, the back bar keeps knitting in the left direction. In weft knit, there are no warp ends, only one end that knits a course. In Tricot, one could knit an open loop or closed loop but Milanese can knit only open stitches. In Fig. 5.6, the Tricot structure is shown with a closed loop diagram and Milanese is shown with the open loop diagram. Unlike Tricot, Milanese has very limited design and stitch variation possibilities.
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
133
5.6 Loop diagram of basic Milanese.
If a silk or cotton yarn that is not uniform is knitted, the non-uniformity in the yarn in Tricot will show going in the wale or length direction and the non-uniformity of the weft Jersey will show going in the course or width direction. However, on Milanese machines the non-uniformity will be diffused as the yarn keeps going sideways at an angle and the second or back bar yarn will go at an angle in the opposite direction.
5.9.3 Types of Milanese machine There are three basic types of Milanese machine: continental flat bed with spring bearded needles and two guide bars; English flat bed, which is similar to the continental machine, except that in place of the two guide bars it has a special mechanical device to control warp ends; and the circular Milanese machine with a latch needle. The continental and English flat bed Milanese machines produce cotton lap and silk lap stitches, whereas the circular Milanese machine produces only the cotton lap stitch. In a flat bed machine, the bars move in opposite directions. Thus, any single warp end from the front bar will travel across the width of the machine from left to right and on reaching the last needle or selvage it will be transferred to the back bar. At the same time, the warp thread on the back bar will start traveling in the opposite direction, now from right to left, moving at the same speed and going to the other selvage. After reaching the left selvage, the warp
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
134 1 2 3 4 5 6
Advances in knitting technology
thread will be transferred back again to the original position completing a full repeat. In a circular Milanese machine, two bars move in the opposite direction at a continuous speed. It is important to note that, like Tricot and Raschel, the circular Milanese machine will not mix front and back bar yarns. Since a flat bed Milanese machine transfers the front bar warp ends to the back bar and thus mixes the two bars, it does not produce the commonly found sandwich-like structure (back bar yarn between the front bar yarn or the bar-on-bar fabrics) of the warp knit fabrics. As mentioned earlier, Milanese machines produce only two basic types of stitch. One stitch is called the Open Cotton Lap (two needle float), where each warp end knits every consecutive needle (0-1, 2-1//2-1, 0-1). The other stitch is called Open Silk Lap (three needle float), in which each warp end knits every other needle or alternate needles only (0-1, 3-2//3-2, 0-1.) Therefore it moves two needle spaces at each course, passing under one needle and over the next. Spun yarns with staple fibers use cotton lap, whereas the silk lap is believed to be for continuous filament yarn – mostly silk yarns. Continental Milanese The continental flat bed Milanese machines are equipped with spring-bearded needles and two guide bars. These machines are built quite similarly to the Tricot and Raschel machines, except for the guide bars and the warp beam setting. As the warp traverses and transfers the warp end from one bar to the other, stationary beams are not used; instead, a movable set of small sectional beams are mounted on the top of the machine. The guide bars are also modified to suit the moving beams. The guides are in units of six, move sideways and have a combined swinging motion, but the needles stay stationary. A section guide is transferred from the front bar to the back bar at one end, and at the other end it is transferred from the back bar to the front bar.
1 2 3 4 5 6 7 8 9 40 1 2 43X
English Milanese English Milanese is a more complex machine than the continental Milanese. Instead of the guide bars, the English flat bed Milanese machine has a special warp control device that contains still points, traverse points, picker points, thread bar and so on. The remaining knitting elements are, however, similar to the continental Milanese machine. Circular Milanese Circular Milanese is a circular machine that uses latch needles and therefore it is quite a simple machine. Two sets of 12-inch beams rotate in opposite directions and feed the warp ends to the needles mounted on a vertical cylinder. The needles have a vertical motion combined with a rocking motion. Unlike the flat bed
© Woodhead Publishing Limited, 2011
Advances in warp knitted fabric production
135
Milanese (continental and English), the circular Milanese machine offers only cotton lap stitch owing to the restricted beam movement. Milanese machines can use only open lap stitch due to the machine design. It is believed that better fabric quality partly results from the open lap stitch. All the Milanese machines in the United States are 168 inches wide and have a 28 gauge (28 npi.) These machines use a special type of 6-inch small spool (56 total spools per machine). Hence, a fully threaded spool or beam has a total of 168 ends per spool. The fringes of these spools are 2¼ inches high and it takes seven to eight hours to set or thread the machine. The Milanese machine knits 64 spm at the mill (8 racks/hr or 48 inch/hr), whereas a Tricot machine knits 2 000 spm (250 racks/ hr or >2000 inch/hr). It is important to note that all Tricot and Milanese fabrics are produced from 20-22 and 30-32 denier only. As silk is not a uniform yarn, the denier of yarn count varies from 20 to 22 denier; hence yarn count is referred to as 20-22. Heavier silk Tricot fabrics of 40 denier or more are neither economical nor aesthetically attractive. The selection of a 20-22 or 30-32 denier fabric depends upon the style and the market trend.
5.10 Conclusion Several commercial fabrics were discussed. The fabrics that were developed and patented by the author when he was working at the DuPont deNemours & Company, were released by DuPont for trade use. Additional information regarding the fabrics discussed, including information on knitting a cotton spun yarn, Modified Americana stitches, can be found in Warp Knit Fabrics Technologies by Professor Bharat J. Gajjar. Any questions about this chapter can be directed to
[email protected].
5.11 Sources of further information Reference material, further explanations and other related information for this chapter can be found in Professor Gajjar’s book Warp Knit Fabrics Technologies. Also, visit www.WarpKnitsOfDE.com. Professor Bharat J. Gajjar is a graduate of Philadelphia University, PA and worked for DuPont deNemours and Company for 35 years, has 20 patents to his name, most related to warp knitting, and he worked as a professor at Philadelphia University Graduate School teaching advanced warp knitting.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
7 Advances in circular knitting D. SEMNANI, Isfahan University of Technology, Iran Abstract: Circular knitting technologies are the most productive methods in the knitting industry. Recently, renowned machinery companies have been developing modern circular knitting machines with a high efficiency production rate and the ability to create special properties in the produced fabrics. Seamless, ultrafine gauge and pile or sliver fabrics are suitable linings for conventional knitted fabrics. Circular knitting technology will lead the textile industry in producing special fabrics once the circular knitting machines are able to produce these fabrics at a high speed and of suitable quality, enabling competitive production of special and industrial fabrics for automotive and medical applications and elegant clothing. Key words: circular knitting, hosiery, jacquard, automotive fabric, technical textile, medical textile, knitted fabric, quality garments.
7.1
Introduction
Until now, circular knitting machines have been designed and manufactured for mass production of knitted fabrics. The special properties of knitted fabrics, especially fine fabrics made by the circular knitting process, makes these types of fabric suitable for application in clothing, industrial textiles, medical and orthopaedic garments, automotive textiles, hosiery, agro and geo textiles, etc. The most important areas for discussion in circular knitting technology are increasing production efficiency and improving fabric quality as well as new trends in quality clothing, medical applications, electronic garments, fine fabrics, etc. Famous manufacturing companies have pursued developments in circular knitting machines in order to extend into new markets. Textile specialists in the knitting industry should be aware that tubular and seamless fabrics are highly suitable for various applications not only in textiles but also in medical, electronic, agriculture, civil and other fields.
7.1.1 Principles and classification of circular knitting machines There are many types of circular knitting machine that produce long lengths of tubular fabric manufactured for specific end uses. Single jersey machines are equipped with a single ‘cylinder’ of needles that produces plain fabrics, about 30 inches in diameter. Wool production on single jersey machines tends to be limited 171 © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
172 1 2 3 4 5
3 4 5 6 7 8 9 40 1 2 43X
Advances in knitting technology
to 20 gauge or coarser, as these gauges can use two-fold wool yarns. The cylinder system of single jersey machines is demonstrated in Fig. 7.1. Another inherent feature of woollen single jersey fabrics is that the fabric edges tend to curl inwards. This is not a problem whilst the fabric is in tubular form but once cut open can create difficulties if the fabric is not finished correctly. Terry loop machines are the basis for fleece fabrics that are produced by knitting two yarns into the same stitch, one ground yarn and one loop yarn. These protruding loops are then brushed or raised during finishing, creating a fleece fabric. Sliver knitting machines are single jersey machines that have been adapted to trap a sliver of staple fibre into the knit structure. Double jersey machines (Fig. 7.2) are single jersey machines with a ‘dial’ that houses an extra set of needles positioned horizontally adjacent to the vertical cylinder needles. This extra set of needles allows the production of fabrics that are twice as thick as single jersey fabrics. Typical examples include interlock-based structures for underwear/base layer garments and 1 × 1 rib fabrics for leggings and outerwear products. Much finer yarns can be used, as single yarns do not present a problem for double jersey knitted fabrics. The technical parameter is fundamental to the classification of knitting machines. The gauge is the spacing of the needles, and refers to the number of needles per inch. This unit of measure is indicated with a capital E. The circular machines now available from different manufacturers are offered in a vast range of gauge sizes. For example, flat bed machines are available in gauge sizes from E3 to E18, and large-diameter circular machines from E4 to
7.1 Single jersey machine.
© Woodhead Publishing Limited, 2011
Advances in circular knitting
173
7.2 Double jersey machine.
E36. The vast range of gauges meets all knitting needs. Obviously, the most common models are those with middle gauge sizes. This parameter describes the size of the working area. On circular machines, the width is the operating length of beds as measured from the first to the last groove, and is normally expressed in centimetres. On circular machines, the width is the bed diameter measured in inches. The diameter is measured on two opposite needles. Large-diameter circular machines can have a width of 60 inches; however, the most common width is 30 inches. Medium-diameter circular machines feature a width of about 15 inches, and the small-diameter models are about 3 inches in width. In knitting machine technology, the basic system is the set of mechanical components that move the needles and allow the formation of the loop. The output rate of a machine is determined by the number of systems it incorporates, as every system corresponds to a lifting or lowering movement of the needles, and therefore, to the formation of a course. The system motions are called cams or triangles (lifting or lowering according to the resulting movement of the needles). The systems of flat bed machines are arranged on a machine component called the carriage. The carriage slides forward and backward on the bed in a reciprocating motion. The machine models currently available on the market feature between one and eight systems distributed and combined in various ways (number of carriages and number of systems per carriage). Circular machines rotate in a single direction, and the various systems are distributed along the bed circumference. By increasing the diameter of the
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
174 1 2 3 4 5 6 7
Advances in knitting technology
machine, it is then possible to increase the number of systems and therefore the number of courses inserted per each revolution. Today, large-diameter circular machines are available with a number of diameters and systems per inch. For example, simple constructions such as the jersey stitch can have up to 180 systems; however, the number of systems incorporated on large-diameter circular machines normally ranges from 42 to 84. The yarn fed to the needles in order to form the fabric must be conveyed along a predetermined path from the spool to the knitting zone. The various motions along this path guide the yarn (thread guides), adjust the yarn tension (yarn tensing devices), and check for eventual yarn breaks. The yarn is taken down from the spool arranged on a special holder, called a creel (if placed beside the machine), or a rack (if placed above it). The yarn is then guided into the knitting zone through the thread guide, which is typically a small plate with a steel eyelet for holding the yarn. In order to obtain particular designs such as intarsia and vanisé effects, the machines are equipped with special thread guides.
7.1.2 Hosiery knitting technology
1 2 3 4 5 6 7 8 9 40 1 2 43X
For centuries, the production of hosiery was the main concern of the knitting industry. The prototype machines for warp, circular, flat and fully-fashioned knitting were conceived for knitting hosiery; however, hosiery production is centred almost exclusively on the use of small-diameter circular machines. The term ‘hosiery’ is used for clothes that mainly cover the lower extremities: legs and feet. There are fine products made of multifilament yarns on knitting machines with 24 to 40 needles per 25.4 mm, such as fine women’s stockings and tights, and coarse products made of spun yarns on knitting machines with 5 to 24 needles per 25.4 mm, such as socks, knee socks and coarse pantyhose. Ladies’ fine-gauge seamless fabrics are knitted in a plain structure on single cylinder machines with holding-down sinkers. Men’s, ladies’ and children’s socks with a rib or purl structure are knitted on double-cylinder machines with a reciprocated heel and toe that are closed by linking. Either an anklet or an overthe-calf length stocking can be produced on a typical machine specification with 4-inch diameter and 168 needles. Currently, most seamless hosiery products are manufactured on circular knitting machines of small diameter, mostly between E3.5 and E5.0 or needle pitches between 76.2 and 147 mm. Sports and casual socks in a plain base structure are now usually knitted on single-cylinder machines with holding-down sinkers. More formal simple rib socks may be knitted on cylinder and dual rib machines termed ‘true-rib’ machines. Figure 7.3 presents the dial system and knitting elements of true-rib machines.
© Woodhead Publishing Limited, 2011
Advances in circular knitting
175
7.3 The true-rib machine in hosiery technology: 1 – needle, 2 – fabric, 3 – needle cam and 4 – sinker cam.
7.2
Current problems and limitations of circular knitted structures
7.2.1 Problems in high-speed circular knitting machines The most important problems in high-speed knitting machines are classified as the limitation of friction occurrence in knitting elements and tension control in the yarn feeding system. Some research has been done about the influence of different parameters and factors among yarn, needles and knitting elements during the knitting operations. Important factors in the contact between yarn and knitting elements during the knitting process are friction, flexural rigidity, the mechanical properties of the yarn and the velocity of knitting elements and yarn in the knitting zone. Amoton’s law for friction occurrence in the dynamic conditions of loop formation during the knitting process states that the yarn tension increases on the yarn supply side of the stitch cam and the lowest tension occurs on the yarn on the other side of the knitting cam. This matters because it is easier to ‘rob back’ yarn from already-formed loops than to pull new yarn from the yarn package, owing to the fact that the tension is higher on this side. The tension on the yarn during knitting is influenced by the number and the angles of yarn wrap between yarn and machine elements, and the fact that robbing back can reduce tension in the yarn. Robbing back is the term for the yarn that comes from the already-formed loops back into the knitting zone, because the yarn tension is lower on this side and higher on the yarn package side. An increase of input tension makes the position of maximum knitting tension move towards the yarn supply side, and with lower input tension the point of maximum knitting tension lies closer to the knitting point. These factors and the fact that many parameters cooperate and influence each other between yarn and machine elements
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
176 1 2 3 4 5 6 7 8 9 10
1 2 3 4 5 6 7 8 9 40 1 2 43X
Advances in knitting technology
make knitting a rather complex process. When it comes to producing knitted structures of yarns or monofilament fibres with high stiffness such as carbon, aramid or polyester mono-filament, parameters such as friction and the flexural rigidity of the yarn are of considerable importance for the knit-ability of the structure. However, a significant problem is that some of these stiff yarns are almost inextensible, which causes tension peaks with breakage of the yarn or single filament in the yarn bundle, especially in high speed knitting operations.
7.2.2 Limitation of pattern in jacquard circular machines The creation of patterns in jacquard machines is limited to a number of knit elements: the yarn feeder system, the needle selection system and the dial needle bar gauge. Mini-jack circular knitting machines are suited to the production of jacquard fabrics. Some models are equipped with selection systems that have 39 levels, 37 of which are for jacquard selection and two for set selections, but more selection elements are limited by the diameter of the dial. The selection is accomplished through a plug-in cartridge or PVC cards, which can be easily changed and programmed separately. Some firms also offer single-bed full jacquard models with electronic needle-by-needle selection to carry out jacquard and operated motifs with virtually unlimited pattern repeats. Some manufacturers have developed a single-bed circular machine for the production of striped jersey fabrics, in versions with 44 four-colour electronic stripe pattern motions, a model for open-worked jacquard fabrics with a diameter of 36 inches and gauge 20–22, as well as a vast range of fully electronic single-bed models for plain or striped three- or four-colour jersey fabrics. These manufacturers also offer a special single-bed machine for jacquard samples, introduced at the ‘Itma ‘99’ fair, with a diameter of 4 inches, two systems and two six-colour electronic stripe pattern motions, with needle-by-needle selection to produce the prototypes of jacquard patterns with enormous time and yarn savings, as it avoids the repeated setting up of a full-size production machine for the various samples. Developed models can be improved by adding the needle-by-needle selection system for the jacquard pattern application if the selection system can work with high-speed machines.
7.2.3 Production limits of seamless knitting machines The most important limitation of seamless knitting machines in circular form is the poor flexibility of these types of machine for producing fabrics in different diameters. In the commonly used method of apparel making in flat fabrics the cutting operation is important. In seamless technology the fabric cannot be cut, and therefore the various diameters should be prepared in the knitting process. This applies to different types of seamless machine of varying cylinder diameters. The short, thin fabrics are knitted in small diameter cylinders and therefore the
© Woodhead Publishing Limited, 2011
Advances in circular knitting
177
production rate is lower. This leads to increasing costs and may be a serious problem for seamless, circular knitting technology. Seamless fabric is knitted in simple structures and there is no advanced jacquard machine to prepare a mixed pattern fabric for this purpose. Seamless circular knitting machines have lately been manufactured to apply a fine gauge as well. These machines are suitable if the benefit of selling price of fabric is justified by the cost of production at a limited rate of production.
7.3
Recent advances in circular knitting
7.3.1 Santoni seamless knitting technology Seamless garment knitting can be achieved either on the circular knitting machine or flat (V-bed) knitting machine. However, seamless circular knitting machines differ from seamless flat knitting machines in that seamless circular machines create only a single tubular type of garment such as those produced on Santoni machines. Seamless knitting machines can create more than one tube and join the tubes together on a machine. The complete garments knitted on circular machines may also only need a minimal cutting operation. In addition, seamless circular machines require different diameters to make major changes in garment size, whereas seamless flat machines can adjust to different garment sizes on the same machine. Consequently, seamless knitting on circular machines is not true seamless knitting. It should be mentioned that knitting on V-bed seamless machines produces truly seamless garments since they do not require any cutting or sewing. In recent years, Santoni has developed a four-feed single-jersey electronic circular machine, which enables the creation of a shaped garment by reciprocal movement. To get a higher quality knitted garment, it is crucial to control the manufacturing functions. It is critical for designers and manufacturers to communicate effectively in order to create successful new products in the knitting industry. Designers complain that the designs that they specified are not accurately created, while technicians are of the opinion that the designers do not understand the technical problems in knitting feasibility. It has been proposed that one way to overcome the communication problem between designers and technicians would be the use of intelligent CAD systems. The CAD system gives designers and manufacturers the opportunity to specify and evaluate their design more precisely without requiring great time investment and technical expertise. Diverse computercontrolled systems including CAD/CAM controlled machines have been developed to facilitate communication. Companies have been offered new types of CAD system, which use two different monitors including a technical window and a design window for designers and manufacturers, who require different information for the same design (Fig. 7.4 and Fig. 7.5). © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
178
Advances in knitting technology
1 2 3 4
7.4 The seamless circular knitting system with CAD/CAM.
1 2 3 4 5 6 7 8 9 40 1 2 43X
7.5 Automatic seamless circular knitting elements.
© Woodhead Publishing Limited, 2011
Advances in circular knitting
179
The technical window shows the developing design in the form of running yarn notations and technical data, while the design window presents the design as a virtual simulation. It is expected to minimise misunderstanding between designers and technicians in the knitting industry.
7.3.2 Ultra fine gauge knitting machines Fine knitted fabrics known as ‘second skin’ are produced on fine gauge circular knitting machines. Cotton, polyester and viscose yarns of 90 to 120 Ne are applied to produce fine circular knitted fabrics. The appearance of these fabrics is similar to woven fabrics but they are more flexible. Groz-Bekert E68 (Fig. 7.6), Mirandsai MV4-3.2 II E60, Havertex BSM2100 E62, and other models are well known, and can produce ultra fine gauge machines. New models by Carl Mayer (MV4-3.2 single and IG 3.2 QC double) are ultra fine with gauge E96. Speeds up to 1.3 m/s in these types of machine (with 3.2 feeders per inch) have been reached. High-grade circular knitting cylinders provide the ideal complement to the company’s premium range of needles and system parts to create the perfect knitting system from a single reliable supplier. It is only with the guarantee of a consistently high standard of component quality and outstanding durability that circular knitting machines are able to reach their full potential for high-performance operation on the factory floor. Ensuring the pinpoint precision of individual elements in existing machines not only simplifies the workflow but also improves capacity utilisation in production. Fine gauge automotive fabrics, known as woven-like fabrics, are produced on fine gauge double cylinders in Pai Lung ultra fine gauge machines. Pile technology
7.6 Ultra fine gauge elements of a circular knitting machine.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
180 1
Advances in knitting technology
is applied to these machines, where the fine gauge of loop makers is adjusted near to the sinkers.
7.3.3 Loop transfer technology in circular knitting machines
1 2 3 4 5 6 7 8 9 40 1 2 43X
Stitch transfer is an important operation, as a higher number of transfer modes means more possibilities of making structured designs and shaped fabrics in which the stitch is transferred from one cylinder to the other or within the same cylinder. All the electronic flat bed machines manufactured in Italy offer the double stitch transfer option, i.e. from one cylinder to the other and vice versa, independently of the carriage direction. In addition, some manufacturers have equipped their machines with an extra cylinder arranged above the machine cylinder and provided with special points to receive stitches from and transfer stitches onto other needles with great freedom of movement. In addition to facilitating the knitting of fabrics with braids or embroideries that require stitch transfers, the third bed also allows significant advantages in the production of shaped fabrics, as the narrowing stitches are transferred onto this cylinder and not onto the dial, diminishing the straining and improving the process conditions. An Italian manufacturer introduced some models including an extra bed with individually selectable points, which operate independently on the front and back bed needles for the lateral transfer of stitches. The production of high-quality knitted fabrics – i.e. of homogeneous appearance as a result of a smooth knitting process and the absence of holes and barring – essentially depends on the application of certain technical solutions that are now adopted by all Italian manufacturers, sometimes with mechanical variants (whether patented or not). As for the type of needle used, Italian machines incorporate latch needles, which operate according to the drowned butt principle. This kind of needle remains in an idle position with its heel completely drowned in the needle bed groove without being involved in the action of cams, and retains the loop, which in this case is not subject to strain. Figures 7.7 and 7.8 demonstrate novel loop transfer elements of these circular knitting machines.
7.3.4 Pile and sliver insertion mechanism in circular knitting A special sliver knitting process locks individual fibres directly into a lightweight knit backing, allowing each fibre to stand upright, free from the backing, to form the soft pile on the face of the fabric. This makes comfort pile fabrics softer, warmer, more drapeable and more resilient than fabrics made from yarns. Each fabric originates from premium loose fibres. These fibres include high-tech microfibre acrylics, polyesters and mod-acrylics specially developed for fabric, along with natural fibres such as wool.
© Woodhead Publishing Limited, 2011
Advances in circular knitting
181
7.7 Loop transfer tool.
7.8 Needle with spring for high speed loop transferring.
Each blend is chosen for its specific end result. By engineering the fibre mix, an incredibly wide range of colours, density, weight, patterning, texture and performance features can be produced in comfort knit pile fabrics. The selected fibres are solution-dyed to ensure consistent, rich, deep colours. The fibres are then blown together in an air chamber, similar to down, blending their colours and fibre types in a predetermined mix. The mixed fibres are then sent through a series of special carding machines that comb the fibres, aligning them parallel to one another. They are then gathered into a soft rope called ‘roving’ or ‘sliver’ – hence the term sliver knitting. The slivers are then fed into sliver inserted fabric state-of-the-art electronic knitting machines as presented in Fig. 7.9 and 7.10. The machine’s fine gauge needles, rotating in a circular motion, pick up fibres from each sliver in a predetermined sequence, locking them directly into soft but strong polyester knit backing. Secured at one end, the length of the fibres remain upright and perpendicular to the backing, allowing them to maintain their resilience, softness, breathability, comfort and light weight. After knitting,
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
182
Advances in knitting technology
1 2 3 4 5
7.9 Sliver feeding system by using feeding rollers.
7.10 Combing tool of the sliver feeding system.
1 2 3 4 5 6 7 8 9 40 1 2 43X
the pile fabric is sheared to the desired height. It is then put through a series of technical finishing processes specially developed by this kind of knitting process to control the surface texture and special characteristics of the final fabric.
7.4
Structure and properties of circular knitted fabrics
7.4.1 Tubular knitted fabrics A variety of elastic fabrics is used for making pressure garments for burn rehabilitation. Such fabrics generally contain elastane, which has the disadvantage of exerting a visco-elastic response to an applied load. If such a fabric is under tension over a period of time, some of the stress in it will be relieved, with a consequent reduction in the skin-and-garment interfacial pressure. A study by Cheng et al. (1983) demonstrated that there is a gradual decline in skin-and-garment interfacial pressure when patients wear the pressure garments over a period of time. Views of doctors, therapists and patients support
© Woodhead Publishing Limited, 2011
Advances in circular knitting
183
their findings: slackening is bound to occur in pressure garments when patients wear them for a long time because the tension of the fabrics has a limited lifespan. Elastic fabrics have different elastic properties lengthwise and widthwise. The rate of tension decay of each elastic fabric depends mainly on there properties, as well as the amount and direction of stretch applied to the fabric. For clinical treatment, it is important to maintain the pressure on the affected area, within a specified range according to instructions from doctors or therapists. The deterioration of tension in the elastic fabrics affects the clinical effectiveness of pressure garments. Tension decay in elastic fabrics means the skin-and-garment interfacial pressure will deteriorate gradually. Elastic fabric can provide the required range of skinand-garment interfacial pressure to the patient during wear. These days, however, pantyhose purchases are down, and although there are many types and kinds of pantyhose, their appearance and sheerness have yet to be satisfactory for women’s needs. The aesthetic properties of pantyhose have long been of great concern to women, and even more so in recent years. Requirements for handling, performance and comfort have been published by Fujimoto et al. (1989) and Harada et al. (1982, 1995).
7.4.2 Influence of structure parameters and relaxation methods on dimensional stability Knitting has always been considered an art. When done by hand, the final product was completely dependent on the weaver’s art, skill and craftsmanship. Even now that 400 years have passed since the first mechanised knitting industry, this value has not changed; the weaver’s art, experience and professionalism can still help create a final product with dimensions and specifications beyond the standard numerical, mechanical and control techniques. At first glance, it seems that such variables create problems in measurements, but this is not the case. All the variables are measurable and controllable, and the most important problem is the precise measurement of dimensional and physical properties of the knitted fabric. One of the most important problems for the knitting industry is the instability of fabrics after knitting, and particularly after their first laundering, which provokes the consumer’s dissatisfaction and may lead to a decrease in demand for the industry. It is to the advantage of the industry that these problems be addressed effectively. This means that there should be criteria for the stability of dimensions in weft knitted fabrics as presented in fundamental research by Fletcher and Roberts (1952), Shinn (1955), Leaf and Glaskin (1955) and Munden (1959). These criteria are expressed as the ‘Ks’ of the intended fabric, and are equal to the density of the stitch multiplied by the square of the stitch length. In the studies carried out in this field, attempts have been made to formulate a geometric model suitable for the stitch that is at complete relaxation so that one can find theoretical
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
184 1 2 3 4 5 6 7
Advances in knitting technology
‘Ks’ for the fabric. This model theory can be applied as a criterion for determining dimensional stability of fabrics (Knapton et al., 1975–1979). Further studies have suggested a three-dimensional structural model for a stitch at complete relaxation, in which according to the calculations, ‘Ks’ for cotton fabric are equal to 26.7765. For a number of weft knitted fabrics at complete rest, attempts have been made to carry out treatments on the fabric at complete relaxation with its ‘Ks’ as close to 26.7765 as possible by actually using chemical relaxants (Semnani et al., 2003). Milano rib fabrics can be used commercially as sportswear, warm outerwear, etc., because they are compact structures with horizontal openings inside the structures, allowing them to retain trapped air and prevent the transfer of heat or cold from one side to the other. Milano rib structures can also be used functionally as technical textiles, for example, by inserting wire, electrical cables, water pipes, yarns, etc., in their horizontal openings. They are also suitable for absorbing impact. The dimensional properties of a fabric are researched for two reasons: to plan a piece of fabric before knitting and to obtain a dimensionally stable fabric. Both reasons are important for fabrics such as Milano ribs, which can be used commercially and functionally. Plain knit and 1 × 1 rib structures are relatively tight fabrics and are subject to jamming. Milano rib fabrics are simple extensions of these two fabrics in that they loosen both the plain and the 1 × 1 rib structures. This applies to cardigan and interlock fabrics, too. These fabrics have a compact structure similar to that of Milano. The relaxation process is especially important for these fabrics in non-equivalent structures of knits. Lately, ultrasonic and mechanical–chemical finishing methods named ‘full relaxation’ have been used in the finishing industry after the knitting process.
7.5
Applications
7.5.1 Seamless knitted garments 2 3 4 5 6 7 8 9 40 1 2 43X
The knitting industry has recently undergone some major advances in the development of seamless whole-garment knitting. One of the main factors for exploring and pursuing the ability to produce seamless whole garments was the ‘labour trap’ (Millington, 2000). For a number of years the garment industry had found it difficult to compete on product price with countries that have a plethora of low-wage labour available. In addition, the more labour required to complete the garment, the more vulnerable the garment producer becomes. Interestingly, the breakthrough of whole-garment knitting has been achieved without a single new advancement in the fundamental knitting process adopted by William Lee when he invented the hand-stocking frame in 1589. The basic principles of knitting remain the same. Today, there are knitting machines that can produce either shaped panels or seamless whole garments. Knitted shaped panels can be sewn together, thereby
© Woodhead Publishing Limited, 2011
Advances in circular knitting
185
eliminating the cutting process. The cutting and sewing process is entirely eliminated by utilising knitting machines that produce seamless whole garments. Several manufacturers of knitting machines are now able to produce whole seamless garments. This is accomplished by utilising multi-needle/transfer knitting elements (Millington, 2000). The machine starts by knitting three separate tubes – two sleeves and a bodice. The three pieces are then joined under the shoulder, creating one large tube. The number of active needles is then gradually reduced, so the tube diameter decreases up to the neckline. The collar is then knitted and the garment is finished off (Stoll, 1998). There are a number of advantages to full-body knitting besides the elimination of the cutting and sewing process. Other advantages include the elimination of uncomfortable seams at the shoulders and underarms and the reduction of fabric waste generated during the cutting process. The full-body knitting machines are capable of knitting numerous shapes and various structures that possess different physical and aesthetic characteristics. There are many potential applications for seamless shaped multidimensional fabrics. Seamless, shaped knitted fabrics can be used in products designed for the industrial, aerospace, automotive, medical and protective clothing industries. Unfortunately, there are some disadvantages in the manufacture of shaped knits. The installation of machines capable of knitting full-body garments has proceeded with some caution. Countries that have a large population willing to work for low wages can produce huge quantities at very low prices. The capital cost of production time alone on a full-body garment machine can still exceed the price that a cut and sewn knitted garment could be purchased for in China. There are also design limitations to the full-body knitting machines; designs cannot be applied to cylinders during knitting. Furthermore, the type of yarns that can be used are limited. In addition, although fabric waste is eliminated in full-body knitting by eliminating the cutting process, waste can be generated through faults. In some cases knitted constructions do not have appropriate physical properties and are therefore not suited for certain end uses. For example, in medical applications, specifically for implantable arterial prostheses, performance characteristics vary according to the demands of the location in which they are used. Knitted prostheses are used because they are easy to suture and possess acceptable thrombogenicity (the ability to cause blood to clot). These particular characteristics make them exceptionally suitable for replacement or bypass of the abdominal aorta and iliac arteries. However, knitted vascular grafts generally have higher porosity and lower strength than woven grafts. In addition, weftknitted structures have a tendency to unravel, particularly when cut at an angle, and have inferior dimensional stability.
7.5.2 Electro textiles Some examples of electro textiles are body conformable antennae for integrating radio equipment into clothing; power and data transmission – a personal area
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
186 1 2 3 4 5 6 7
Advances in knitting technology
network; flexible photovoltaics integrated into textile fabrics; the capacity for physiological status monitoring to monitor hydration and nutritional status as well as the more conventional heart monitoring; quality footwear that can also convert and conserve energy; and, of course, phase change materials for warming and cooling of the individual. Taping a battery and an LED to a magnet was easy in T-shirts or other knitted apparels. It was fun, and consequently embraced wholeheartedly by all. The Throwie was soon expanded and modified, morphing into massive multi-LED on structures, clip-on clothes lights, or mega magnet monsters. Theoretically, it might have been difficult to explain the process to a diverse audience, but once the technology was clear, comprehension and creativity flowed.
7.5.3 Automotive textiles
1 2 3 4 5 6 7 8 9 40 1 2 43X
A prime requirement of any textile vehicle seat or door panel base fabric is the ability to apply both visual and aesthetic quality to the product. This may seem somewhat self-evident but many fabrics have been developed in attempts to perfect these properties. Base fabrics should be capable of design and colour variations on short development time scales. One such product is circular fabrics (DNBR), which is in many ways an ideal product with a pile surface, high production rates, low cost, some stretch for ease of engineering, etc., but it lacks the ability to have large surface patterns applied easily and efficiently, without dramatically affecting cost. The result of this in recent years has been that this technology has lost out to more ‘design friendly’ processes such as circular-knitted products. Similar comments could be made of loop-raised tricot fabrics, where fabric aesthetics rather than surface pattern predominate. New ways of applying design to fabric such as ink-jet printing, however, mean that such fabrics could again come to the fore as print substrates, and could compete favourably with jacquard technologies, which are at the moment dominant in the production of figured fabrics. Seat cover fabric must always appear non-creased, and for this reason it is usually laminated to polyurethane foam, with a thickness varying from about 2 to 10 mm. In addition it must resist soiling and be easily cleanable without ever being put into a washing machine. Lamination to polyurethane foam also imparts a soft touch to the fabric, and deep and attractive sew lines are formed in the production process. To help the seat cover slide along the sewing machine surface during manufacture, and to assist sliding when the made-up cover is pulled over the seat structure, a scrim fabric is laminated to the other side of the polyurethane foam. The scrim also helps to control the stretch properties of the seat cover, especially when knitted fabrics are used. Thus, the cover ‘fabric’ is usually in the form of a triple laminate for seats, but when used for door casings the ‘fabric’ (laminate) is used without the scrim. At present the most important technical requirements of a car seat covering fabric are cost, UV degradation resistance,
© Woodhead Publishing Limited, 2011
Advances in circular knitting
187
light fastness, abrasion resistance and soil resistance. The latter is a natural property of polyester, which can be improved by a fluorocarbon after-treatment if necessary. Once this has been decided, effort should be diverted to the pile yarns that form the aesthetic surface of the fabric, as these can be of an infinite variety with a much greater choice available than for, say, the circular-knitted pile cloths. Figure 7.11 demonstrates the portions of circular knitted fabric that have been used in automotive textiles from 2000 to 2009.
7.5.4 Orthopaedic applications The medical sector is probably the one with the strongest influence on technical textiles, due to its wide application in medical centres, hospitals and first aid centres. Tubular fabrics with elastic weft insertion optimise the compressive effect and are much used in post-operating treatments on articulations in the knee, elbow and ankle. Also, they are frequently used in muscular recuperation processes and orthopaedic treatments (Fig. 7.12). Tubular fabrics of rib texture are produced on weft circular machines, with a mixture of polyester yarns and polyamide recovered elastic yarn of 90 denier. One of the most visible examples are the elastic meshes for use in bandages, compresses and the subjects for post-operating implants. Meshes produced on warp circular machines, with a mixture of polyester yarns and polyamide, also exhibit similar elasticity. The advantages of these fabrics over the traditional fabrics are as follows: they allow transpiration of the skin avoiding allergies; they are easy to apply and adaptable to any part of the body; and they enable more oxygenation of the wound. Knitted cords in polyester/polyamide with a lycra core are used in surgery masks thanks to the adaptability and comfort of the material. The rigid bandages for application in hospitals and first aid centres are supplied in rolls, with the laterals
7.11 The portions of circular knitted fabric in automotive textiles.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
188
Advances in knitting technology
1 2 3 4 5 6
7.12 Tubular fabrics with elastic weft insertion for orthopaedic application.
2 3 4 5 6 7 8 9 40 1 2 43X
knitted, avoiding stray yarns, which can produce infections. The crochet fabric allows higher and immaculate adaptation to the wounds. Bandages are produced with cotton weft and warp. The semi-elastic bandages, thanks to the composition of their polyester warping and/or weft yarns/polyamide texture, give some elongation (elasticity) which allows their use to protect wounds and provide compression. The use of warping rubber yarns lends elasticity to bandages (Fig. 7.13), in many cases up to 200%, increasing their compression properties and making them ideal for muscular contusions and orthopaedic applications. The structure and fibre used in this kind of bandage allow its use in plastering at first aid and emergencies, due to its strong compressive capacity. The structural composition of the fabric in this kind of bandages allows its use in surgical procedures in order to protect fabrics and to be used as prostheses. Tubular fabrics are used for skin protection against plasters, preventing the contact of the skin with the plaster. Another application is its use as protective and subjection bandage. Tubular fabrics are produced on weft circular machines and come in a range of diameters from 1 to 10 inches covering all necessary applications. Rib tubular fabrics of small diameter are commonly used in cuffs, but due to their compressive effect they are also used for the cuffs of sleeves for surgery
© Woodhead Publishing Limited, 2011
Advances in circular knitting
189
uniforms by optimising their capacity for closing and preventing the dispersion of micro-organisms in surgical procedures (Fig. 7.14). Rib tubular fabrics are produced in most weft circular machines.
7.6
Future trends: smart garments
Smart knitted fabrics can be made due to advances in many technologies coupled with advances in textiles and structures. At a glance, the production of elegant
7.13 Elastic bandages.
7.14 Tubular knitted fabrics in surgery uniforms.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
190 1 2 3
circular knitted materials such as seamless fabric is due to advances in biotechnology, information technology, microelectronics, wearable computers, nano-coated and micro electromechanical devices. In many cases the purpose of these systems is to provide both military and civilian personnel engaged in highrisk applications with the most effective survivability technologies. Some new applications of knitted garments in circular form are being developed, such as the introduction of conformal antennas to the fabric body for integrating radio equipment into clothing, power and data transmission devices in the knitted structure, photovoltaic integrated into fabrics, smart footwear, quality knitted coating in home applications such as carpets or covers, energy-converting and protective tubular fabrics, which generate electricity from the thermal energy in people’s movements, and the application of phase changing materials for heating and cooling of the individual (used in double face knitted fabrics, or spacer fabrics that are knitted in circular knitting machines). The specific features of circular knitted fabrics such as flexibility, seamless structure and contactability make the circular knitting industry the most improved quality textile sector of the future.
7.7
1 2 3 4 5 6 7 8 9 40 1 2 43X
Advances in knitting technology
References
Addington, Michelle and Schodek, Daniel (2005). Smart Materials and Technologies for Architecture and Design Professions. Oxford: Elsevier. Cheng, J. C. Y., Evans, J. H., Leung, K. S., Clarke, J. A., Choy, I. T. C. and Leung, P. C., Pressure therapy in the treatment of post-bum hypertrophic scar; A critical look into its usefulness and fallacies by pressure monitoring, Burns, 10, 154–163 (1983). Double knit electronic circular knitting machine, Santoni Company, http://santoni.com/ en-macchine-item.asp. Double-Jersey Machines: Overvie, Mayer & Cie GMBH (2007), http://www.mayercie.de/ en/produkte/43_269.htm. Exclusivity in ultra-fine fabrics. On the circular knitting machine, Mayer & Cie GMBH (2007), http://www.mayercie.de/en/produkte/43_623.htm. Fletcher, H. M. and Roberts H. S. (1952). The geometry of plain and rib knit cotton fabrics and its relation to shrinkage in laundering. Textile Research Journal, 22, pp. 84–88. Harada, T. and Fusaka, K. (1982), Wear feeling of pantyhose, Japan Research Association for Textile End-Uses, 23, 135. Inamura, A., Nakanishi, M., and Niwa, M., Relationship between wearing comfort and physical properties of girdles, Japan Research Association for Textile End-Uses, 36, 109 (1995). Knapton, J. J. F. (1979). Wet-relaxed dimensions of plain-knitted fabrics. Journal of the Textile Institute, 70 (9), 410–411. Knapton, J. J. F. Truter, E. V. and Aziz, A. K. M. (1975). The geometry, dimensional properties, and stabilization of cotton plain-jersey structure. Journal of the Textile Institute, 66 (12), 413–419. Knitting International (2004a). Shima offers new print option. 111 (1314), 21. Knitting International (2004b). Lonati buys Sangiacomo, 111 (1317), 19. Knitting International (2004c). World equipment buyers’ guide 2004, 111 (1318), 45–75. Knitting International (2004d). Hosiery after-care specialists, 111 (1320), 30–31.
© Woodhead Publishing Limited, 2011
Advances in circular knitting
191
Knitting International (2004e). Stoll launches flexible all-rounder, 111 (1321), 15. Knitting International (2005). Flexibility is key for cortese, 112 (1328), 42. Leaf, G. A. V. and Glaskin, A. (1955). Geometry of plain knitted loop. Journal of the Textile Institute, 46, 587–605. Millington, John. (2000) Complete garment manufacture. Textile Asia, July, 32–37. Munden, D. L. (1959). The geometry and dimensional properties of plain-knit fabrics. Journal of Textile Institute, 50, 448–471. Santoni (2006a). Retrieved January 11, 2006, from http://www.santoni.com. Santoni (2006b). Seamless Apparel Symposium. Greensboro, North Carolina, April 4. Semnani, D. Latifi, M. Hamzeh and S. Jeddi A. A. A. (2003). A new aspect of geometrical and physical principles applicable to the estimation of textile structures: and ideal model for the plain-knitted loop. Journal of the Textile Institute, 94 (1), 202–211. Shinn, W.E. (1955). An engineering approach to jersey fabric construction. Textile Research Journal, 2, 270–277. Single jersey electronic circular knitting machine, Santoni Company, http://santoni.com/ en-macchine-item.asp. Single-Jersey Machines: Overvie, Mayer & Cie GMBH (2007), http://www.mayercie.de/ en/produkte/43_70.htm. Smart textiles, http://www.smartextiles.co.uk/_f_1_1.htm (November 1, 2007.) Softswitch Electronic Fabrics-Applications. (2001). Retrieved July 23, 2001: http://www. softswitch.co.uk. Spencer, D. (2001). Knitting Technology, a Comprehensive Handbook and Practical Guide. Stoll, Thomas (1998) New knitting technologies on the flat knitting machine. International Textile Bulletin, May, 61–66.
Further reading Banerjee, P. K. and Alaiban, T. S. (1988), Geometry and dimensional properties of plain loops made of rotor spun cotton yarns, Part III: Spirality of the wale line. Textile Res. J. (558), 287–290. Baurley, S., (2004). Interactive and experiential design in smart textile products and applications. Pers Ubiquit Comput, 8–15. Brackenbury, T. (1992). Knitted Clothing Technology. Oxford, Boston: Blackwell Scientific Publications. Bremmer, N. (2005). Circular knitted striped fabrics. Knitting International, 112 (1324). Fujimoto, T. (1989), The evaluation of performance of women’s pantyhose, Part I: Characteristics of deformations in the wearing test and the size effects, Japan Research Association for Textile End-Uses, 30, 80. Fung, Walter and Hardcastle, Mike (2001). Textiles in Automotive Engineering. Cambrige: Woodhead Publishing. Groz-beckert, INFO KN newsletters numbers 2, 4, 7, 8, 9 and 10, now available at http:// www.grozbeckert.com/sprache_english.asp. Harada, T. (1995), Comfort of clothing and sense measurement. Japan Research Association for Textile End-Uses, 36, 24. Hum, A. P. (2001). Fabric Area Network – A new wireless communications infrastructure to enable ubiquitous networking and sensing on intelligent clothing. Computer Networks 35(ER4), 391–399.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
192 1 2 3 4 5 6 7 8
Advances in knitting technology
Hunter, B. (2004a). Complete garments – evolution or revolution? (Part I). Knitting International, 111 (1319), 18–21. Hunter, B. (2004b). Complete garments – evolution or revolution? (Part II). Knitting International, 111 (1320), 22–23. Hunter, B. (2004c). Complete garments – evolution or revolution? (Part III). Knitting International, 111 (1321), 20–22. Issacs, M. (2005). Seamless: Eliminating stitches – more than a buzzword. AATCC Review, 5 (11), 16–19. Knit Americas (2001). Seamless sweaters here to stay. Winter, 22–23. Knit Americas (2005). What next for seamless body size clothing? Fall, 20. Linda, G. and Leggett, N. (1990). The Machine Knitter’s Dictionary, London: Batsford. Needle Detector NW from Memminger-IRO, reference 335.905.001.07 DSNL/5, official website http://www.memminger-iro.de/. Onal, L. (2003). The relation of seam-free garments and mass customization. International Textile Bulletin, 49 (3), 44. Paradiso, R. (2006), Seamless H-health systems. Knitting International, P25–26. Powell, N. B. (2003). Italian Textile Technology. Textile World, 153 (6). 40–41. Push, T., I. Wunsh, R. Seifert and P. Offermann (1997), Fine structure of yarn tension on large-diameter circular knitting machines, Melliand textilberichte, 1–2, 52–55. Rajkhowa, I. (2000). Wear your PC. Computers Today, October 31, 90–92. Roberts, S. (2000). Intelligent Garments – Fact or Fiction? Just-Style Features, May 11. Santoni. (2004). Know-How: Santoni. Brescia, Italy: Gruppo Lonati. Schoeser, M. (2003). World Textiles: A Concise History. New York: Thames & Hudson World of Art. Semnani, D. and M. Sheikhzadeh (2007), Online control of knitted fabric quality: Loop length control. International Journal of Electrical Computer and Systems Engineering, 1 (4), 213–218. Semnani, D., K. Matin, M. Sheikhzadehand and M. Latifi (2008), Automation of stitch length cams in high speed flat knitting machine: Online control system and numerical modeling method. International Journal of Applied Engineering Research, 3 (6), 763–772. Shanahan, W. J. and Postle, R. (1973), Jamming of knitted structure. Textile Research Journal, 43, 532–538. Siewiorek, D. (1999). Wearable computing comes of age. Computer, 32 (5), 82–84. Spencer, D. (1989). Knitting Technology (2nd ed.). Cambridge: Woodhead Publishing. Vigo, T. L. and Bruno, J. S. (1988), Properties of knits containing cross-linked PEG. Book chapter/publication, International Conference & Exhibition, AATCC, 83–173.
4 5 6 7 8 9 40 1 2 43X
© Woodhead Publishing Limited, 2011
8 Knitted fabric composites M. DUHOVIC and D. BHATTACHARYYA, University of Auckland, New Zealand Abstract: This chapter discusses the role of knitted fabric structures as reinforcing elements in polymer composite materials. The types of fibres, yarns and knit structures used to produce knitted fabric composites are presented along with the techniques used to combine them with different types of polymer matrices. An insight into some of the commercially available textile composite precursor (prepreg) technologies is given together with the manufacturing methods, mechanical properties and applications associated with these materials. Key words: textile composite materials (TCMs), high performance fibres, prepregs, multiaxial warp knits (MWKs), sheet forming.
8.1
Introduction
8.1.1 Brief introduction to polymer composites A composite can be defined as a combination of two or more dissimilar materials whose combined properties are superior to those of the individual constituents. Considering the synergistic effects that are achievable by some of today’s composite materials, it is not uncommon to hear expressions amongst composite circles such as 1 + 1 = 11. While expressions like these may disgruntle mathematicians, they remain one of the principal advantages pertaining to the use of composite materials today. It is no mystery that engineers have long used nature as a source of inspiration and examples of composite materials are to be found in mammals, plants as well as geological formations (Chou and Ko, 1989). Wood, a natural composite containing cellulose fibres and lignin (a natural polymer), is one of the most common materials used in the construction industry today. Even man-made composites have existed for many years with the use of clay plus grass to form bricks and other building materials as the classic example (Chou and Ko, 1989). However, it was not until the 1950s that a feasible synthetic composite, fibre reinforced plastic (FRP), emerged, which was able to replace wood and metal in many applications. As research progressed, manufacturing processes and materials were developed to meet the demands of high tech applications such as the aircraft/aerospace and defence industries. The opportunity was there to use FRPs for commercial applications but the cost of producing them was still too high. Continued progress in manufacturing techniques over the past ten years, including the evolution of 193 © Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
194 1 2 3 4 5 6 7 8
2 3 4 5 6 7 8 9 40 1 2 43X
Advances in knitting technology
more structured types of fibre reinforcements using textile technologies, has allowed FRPs to become a prime candidate for consumer products such as sports equipment, appliances, electronic and corrosion resistant equipment and most of all transportation (Astrom, 1997, p. 103; Ko et al., 1999). Overall there is a wide range of current applications for reinforced thermoplastic composite materials, in particular, that benefit from textile reinforcements.
8.1.2 The role of knitted fabrics in polymer composites Over the past decade, research with regards to the understanding of the forming characteristics of fibre-reinforced thermoplastic composite materials has steadily progressed. New polymer materials are constantly being developed to provide more favourable forming as well as final mechanical property characteristics. On the other hand, fibre reinforcements seem to have followed a similar trend ranging from the development of simple and random to highly structured configurations. This trend has led to research in the area of so-called textile composite materials. Textile composite materials (TCMs) constitute a form of fibre-reinforced polymer, where the reinforcing fibres are structured in such a way as to provide favourable forming characteristics while preserving the fibre continuity needed for final component strength. TCMs represent an important development as far as composite preform materials are concerned since they allow for much easier handling of raw materials. However, the greatest potential of these materials must lie in the fact that the technology to produce the complicated reinforcing structures economically has existed for a number of years in the apparel industry. Now the challenge lies in being able to combine this technology reliably and economically with composites processing and in being able to develop a scientific understanding of these materials that will allow reasonable predictions of both the forming behaviour and end product’s overall mechanical property characteristics. One of the current problems associated with FRPs seems to be the trade-off between final component strength and processability. FRPs for structural applications usually consist of long continuous inextensible reinforcing fibres in the loading directions. This is very favourable for the final component but poses significant problems during the forming stages in many manufacturing processes where virtually inextensible fibres restrict the movements required to form the part. TCMs partially relieve this restriction by allowing for fibre movement through certain modes of compliance present in the geometric structure of the textile reinforcement. Processability, stiffness, strength, interlaminar fracture toughness and material cost also play an integral role in determining the relative advantages and disadvantages of certain FRPs. Figure 8.1 presents a general comparison of these
© Woodhead Publishing Limited, 2011
Knitted fabric composites
195
8.1 Overview and comparison of the main existing reinforcement types and their composite properties (Houtte et al., 1998).
properties for the main existing types of FRP materials available today (Houtte et al., 1998). Positioned roughly in the centre of Fig. 8.1, knitted fabrics generally possess stiffnesses and strengths that are lower than those of woven or braided fabrics but are higher compared to those of randomly oriented continuous or short fibre mats. Their geometry, which allows a considerable amount of intermingling, results in an interlaminar fracture toughness far superior to that of any two-dimensional weave or braid. As far as processability of complex shapes is concerned, this is where knitted fabrics show their biggest advantage, allowing large strains and shear angles without the occurrence of wrinkling. Although randomly oriented continuous and short fibre mats may seem to have an upper hand with regard to processability, their composites are often susceptible to tearing, resulting in weak spots and inhomogeneous fibre content, problems which do not arise readily in knitted fabrics. The degree of isotropy is a favourable characteristic, a material property only bettered by randomly oriented continuous and short fibre mats. Finally, given that knitted fabric composites are still in the developmental stage, raw material and subsequent composite production cost are an unknown factor for now. However, industrial knitting is a technologically advanced production technique that has gone through many years of refinement in the garment industry, making the initial cost image for knitted fabric composites very favourable. It is not suggested that knitted fabric composites provide the single solution for FRPs but they fit neatly into the broad family of FRP composite materials. Certainly for applications requiring moderate stiffness and strength and excellent processability, they will be the obvious choice.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
1 2 3 4 5 6 7 8 9 10
196
Advances in knitting technology
8.2
Types of fibre and yarn used in knitted fabric composites
8.2.1 High performance fibres To qualify for primary and secondary load bearing applications, knitted fabric composites must be made from high modulus and high strength fibres. Amongst the most common types of commercially available fibre used are glass, carbon, aramid and steel along with some selected natural fibres (see Table 8.1) (Miravete, 1999; Bhattacharyya and Fakirov, 2007, p. 34). With each type of fibre comes a different set of favourable and unfavourable properties. However, availability and cost are usually the determining factors for their use. At around US$2.00 per kg, and considering their relatively good performance compared to other materials, E-glass fibres remain one of the most extensively used reinforcement fibres in industry today. It is interesting to note that the cost of the commingled continuous E-glass and polypropylene yarn composite preform Twintex® is only slightly more expensive than glass fibre yarn on its own. Polymer fibres Although polymers are usually used as the matrix element of the composite, there are several high performance polymers that provide mechanical properties adequate for use as reinforcing elements. Aramids, liquid crystalline polymers and ultrahigh-molecular-weight polyethylene all have sufficient strengths and Table 8.1 High performance fibre materials for knitted fabric composites (Miravete, 1999; Bhattacharyya and Fakirov, 2007)
1 2 3 4 5 6 7 8 9 40 1 2 43X
Material Density Failure stress (MPa) (g/cm3)
Failure strain (%)
Young’s *Yarn Modulus fibre cost (GPa) (US$/kg)
E-Glass S-Glass Aramid (Kevlar 49) High StrengthCarbon High ModulusCarbon Steel Twintex® Vf 60%/75% Flax Sisal Jute
3.5–4.8 4.0–5.4 2.5–2.7 1.5–2.2 0.6–1.4 20 – 2.7–3.2 2.0–2.5 1.5–1.8
73 88 133 230–300 345–590 205 – 27.6 9.4–22.0 26.5
2.58 2.48 1.45 1.76–1.80 1.83–1.90 7.9 – 1.5 1.5 1.3
2400–3450 3100–4590 3500–3600 3300–6370 2600–4700 275Y/430UTS – 345–1035 511–635 393–773
2.00 11.00 24.00 16–24 100–200 27–35 2.93/3.04 3.50–7.20 10.70 1.00–3.00
Note: costs are approximate average values for fibres in yarn form collected from various sources on the internet as well as direct communications with suppliers. *For natural fibres cost is dependent on yarn size and refinement, e.g. for flax 20 lea = US$7.20/kg, 4 lea = US$3.50/kg.
© Woodhead Publishing Limited, 2011
Knitted fabric composites
197
stiffnesses for use as reinforcement fibres. These high-performance organic fibres are used extensively in military applications ranging from body armour, helmets, and safety shoe toe caps to protective armour in ground vehicles (Bond-Laminates, 2007). One example of an organic polymer fibre with extremely high mechanical properties is produced by Akzo Nobel in the Netherlands (Northbolt et al., 2002). The M5® fibre is the registered trade name for poly{2,6-diimidazo[4,5-b:4´,5´-E] pyridinylene-1,4-(2,5-dihydroxy)phenylene} or PIPD which has been engineered over a 10-year period. The team of scientists led by Doetze Sikkema have achieved modulus values greater than 300 GPa and tensile strengths greater than 5 GPa (Northbolt et al., 2002). Its high damage-tolerance makes it suitable for knitting and composites made of M5® are reported to show good ductility and impact strength (Northbolt et al., 2002). Micro- and nano-fibrillar fibres Using another technique, even low strength polymers can be processed together in such a way as to produce high strength yarns for use in composite materials. Micro- and nano-fibrillar reinforced composites are prepared by extruding and drawing continuous filaments of immiscible polymer blends of different melting temperatures. By processing the material at the melt temperature of the lower melting point polymer a highly desirable method of in-situ fibre formation is created, reversing the effects of immiscibility and producing blends with improved mechanical performance, in some cases on their own comparable to glass fibre reinforced plastics (Van Gheluwe et al., 1988). Commonly used materials are combinations of polyethylene (PE) and polyethylene terephalate (PET) or polypropylene (PP) and PET amongst several other combinations, the properties of which have been extensively studied by Fakirov et al. (2008) and many others (Shields et al., 2008; Yang et al., 2003; Sarkissova et al., 2004). The continuous filaments can be assembled into yarn and used to produce knitted fabric composite preform materials. Natural fibres Due to the lower and less consistent mechanical properties of natural fibres, not many qualify as worthy candidates for use as reinforcing materials. Among the strongest are ramie, jute, sisal and flax. Certain varieties of flax have been reported in the literature as having ultimate tensile strengths of up to 1500MPa; however, even this range varies from 345–1035MPa to 800–1500MPa (Bhattacharyya and Fakirov, 2007, p. 336). Large variations also appear with regard to the Young’s Modulus, 27.6 GPa and 60–80 GPa (Bhattacharyya and Fakirov, 2007, p. 621). Nevertheless, by offering the best mechanical properties compared to other natural fibres, they can produce composites with mechanical characteristics comparable with that of E-glass fibres (Duhovic and Bhattacharyya, 2007). If the specific
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
198 1
Advances in knitting technology
properties and eco-friendliness of these fibres are taken into account, they become very attractive alternatives.
8.2.2 Yarn types Most high performance fibres are produced by extrusion and drawing, resulting in continuous filaments and subsequently continuous filament yarns. This is more favourable in composite applications since they produce materials with higher stiffness and strength in the desired applications compared to short fibre yarn assemblies. In the textile industry, hybrid yarns are used to incorporate different properties into garments and to minimise the cost. For composite applications, hybrid yarns are also used to optimise costs, mechanical properties and in some cases, even the processability. In one type of thermoplastic composite preform, commingled hybrid yarns are used to promote easier fibre wetting and improve consolidation quality.
8.3
Composite preforms
Perhaps the biggest factor contributing to the increasing use of FRPs has been the development of their composite preforms. This is true for thermoplastic composites in particular, where advantages such as safe processing environment and the potential for high volume production have been offset by relatively difficult-toachieve impregnation quality. Composite preforms eliminate some of the processing difficulties with regard to fibre impregnation quality and allow for quicker and more manageable processing at the end user level. For thermoplastic composites with their high melt viscosities, in the range of 100–10 000 Nsm2, compared to 0.1 to 10 Nsm2 for thermosetting composites, ensuring good impregnation quality becomes an even greater challenge.
1 2 3 4 5 6 7 8 9 40 1 2 43X
8.3.1 Textile preforms for composites The specific assemblage or arrangement of continuous (or discontinuous) fibrous materials into a form, which becomes the reinforcement for a composite, is known as the textile composite preform (Chou and Ko, 1989). Of course, there literally exists an infinite number of configurations for these preforms ranging from simple to complex 3D geometric fibre orientations. The architecture used is in many cases tailored best to fit the application, which explains why many of these materials are not produced commercially. For knitted structures, it is a common practice to obtain the preform material in a more unrefined form such as continuous filament yarn or roving, and to produce the fabric using industrial knitting machines obtained from specialist textile manufacturers. The development of textile preforms, knitted structures in particular, have attracted much interest, mainly for two reasons: i) their ability to preserve fibre
© Woodhead Publishing Limited, 2011
Knitted fabric composites
199
continuity for strength while allowing for increased forming flexibility and ii) the fact that processing techniques known for many years from the textile industry can be readily applied in high volume production and at low cost. Preforms such as bidirectional woven mats provide a low degree of forming flexibility but high final strength. Stapled or chopped fibres provide a forming flexibility close to that of the thermoplastic alone; however, the final strength of the component is compromised. Knitted fabric preforms attempt to bridge the gap between forming flexibility and strength while offering a greater in-plane shear resistance than either of the aforementioned (Chou and Ko, 1989). One main disadvantage associated with textile preforms is that they commonly rely on impregnation subsequent to shaping and depend on the end user rather than the specialist manufacturer to ensure impregnation quality.
8.3.2 Textile composite prepregs Composite ‘prepregs’ (pre-impregnated composite fibres) reduce the risk of poor impregnation quality by ensuring that the correct amount of each constituent material is already present and interacting. The development of thermoplastic composite prepregs began in the late 1980s with materials consisting of unidirectional or woven high-strength fibres neatly impregnated into thermoplastic matrices. In the 1990s, commingled technologies using E-glass polypropylene/ polyethylene terephthalate became available in the form of rovings and fabrics. Twintex® roving manufactured by Saint-Gobain Vetrotex (Chambéry, France) (bought by Owens Corning as of 1 February 2007) is one example of a commonly available thermoplastic composite preform. It is a roving consisting of commingled continuous thermoplastic and glass fibre yarns, which are suitable for knitting. Other techniques used to combine thermoplastic matrix and reinforcement include film stacking (Bond-Laminates’ Tepex® and TenCate’s Cetex®), and powder coating reinforcement yarns (Hexcel Composites’ Towflex®), see Fig. 8.2. However, for these materials, woven rather than knitted reinforcement structures are more common. Figure 8.3 shows a selection of currently available thermoplastic composite preform and prepreg materials, four of which use textile composite technology.
8.2 Methods for combining thermoplastic matrices with reinforcement fibres.
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
200
Advances in knitting technology
1 2 3 4
8.3 A range of currently available thermoplastic composite preform/ prepreg materials.
2 3 4 5 6 7 8 9 40 1 2 43X
Twintex® can be classified as a textile composite preform, since no bonding between the constituent materials has taken place. Towflex® is a textile composite prepreg since the powder coating has partially established the bond between the fibre and the matrix. Plytron® can also be classified as a composite prepreg, but it is not considered a textile. Tepex® and Cetex® are woven fabric composite prepreg sheet materials produced by using film stacking and double-belt-press methods. Although the focus in this section has been on thermoplastic impregnation techniques, moulding using thermosetting matrices is far more common and established in industry. In processes such as resin transfer moulding (RTM), structural reaction injection moulding (SRIM) and resin film infusion (RFI), the injected low viscosity thermosetting resin flows into and around the textile structure made from the high performance fibres. The material is then cured at room temperature (or elevated temperatures) for several hours to set the resin and form the composite material. Partially cured mouldable thermoset prepreg materials are also common and are available in woven and yarn form, but are not suitable for knitting due to their tackiness.
© Woodhead Publishing Limited, 2011
8.4
Knitted fabric composites
201
Knit structures for fabric composites
Plain warp- and weft-knitted structures are not commonly used for composite applications due to their inherent anisotropy in the wale and course directions. This causes the fabric preform to roll up on itself making handling and manufacturing more difficult. This problem is solved by using weft-knit structures such as the 1 × 1 rib and milano rib, which exhibit balanced properties because of their through-thickness symmetry. However, the highly curved fibre architecture, or crimp, present in these and any knitted structure, means that composites produced using these structures exhibit relatively poor mechanical performance. Characteristics of high conformability and low strength make them ideally suited to producing semi-structural complexly shaped components. To help increase mechanical performance, insert yarns can be placed between the planes of loops in either the warp or weft direction. The technique can be used for both warp- and weft-knitted fabrics which allow the insert yarns to remain perfectly straight, giving a greater yarn to fabric translational strength. This results in an increase in the composite stiffness and strength along the insert direction. Warp- and weft-knitted fabrics with inlay yarns are termed unidirectional knitted fabrics and the incorporation of insert yarns in two directions creates biaxial knitted fabrics.
8.4.1 Multiaxial warp knits Multiaxial Warp Knit (MWK) fabric is a further development of this idea by utilising layers of insertion yarns for the in-plane reinforcement and warp stitch yarns for the through-thickness reinforcement. They consist of one or more parallel layers of yarns held together by a warp knit loop system. Theoretically, as many layers as preferred can be used but typical commercially available machines only allow four layers (Du and Ko, 1996). The purpose of the knit loops is to hold the layers of unidirectional yarns together, but it has also been proven to be the key to increasing the damage tolerance of the material (Zhou et al., 2005). These types of knitted structure are termed non-crimp structures and can be produced in a single knitting process (Du and Ko, 1996). They are particularly suitable for thin to medium thickness parts. The combination of the warp-knitted structure and non-crimp yarns means they have the ability to conform to complex shapes as well as the potential to meet the demands of primary load bearing applications. MWKs have evolved through structural modifications of warp-knitted fabrics and are predominantly fabrics with inlay yarns in the warp (90°), wale (0°) and bias (± θ°) directions. Warp, weft and bias yarns are held together by a chain or tricot stitch through the thickness of the fabric (Du and Ko, 1996). Layers of 0° need to be placed somewhere other than the top or bottom layer to ensure structural integrity. The amount of fibre and the orientation of the inlay yarns can be
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
202 1 2 3
Advances in knitting technology
controlled, which is advantageous for preform engineering. As a result, the insert yarns are made from a much higher linear density yarn than the stitch yarns, since they form the load-bearing component of the fabric structure (Du and Ko, 1996). Figure 8.4 shows the configuration of the chain and tricot MWK structures. An improved MWK structure for composite reinforcement, developed by replacing the tricot stitch with a ‘double loop pillar stitch’, has been carried out by Zhou et al. (2005) The modification has yielded improvements of up to 7% in breaking strength (Zhou et al., 2005). The tribology or wear resistance of MWK has also been investigated and has been shown to perform better than biaxial nonwoven structures (Mathew et al., 2007). With respect to composite mechanical properties, MWKs provide the most practical solution for the use of knitted structures in composite materials.
8.5
Types of matrix materials
Matrix materials for knitted fabric composites follow the same criteria that apply to composite materials in general. Important characteristics are fibre-to-matrix compatibility in terms of bonding, mechanical properties, thermal properties, cost and most importantly, processability. The two broad categories of polymers used are thermosets and thermoplastics.
8.5.1 Thermoplastic materials Thermoplastic materials are popular due to their user-friendly safe processing, and they can be melted, shaped and cooled into a dimensionally stable part in a matter of seconds. Processing temperatures start at around 120 °C for polyethylene but can be as high as 345 °C for high-performance engineering thermoplastics such as poly(ether ether ketone) (PEEK). Due to the high viscosity of thermoplastics,
1 2 3 4 5 6 7 8 9 40 1 2 43X
8.4 Chain and tricot stitched multilayered MWK structures.
© Woodhead Publishing Limited, 2011
Knitted fabric composites
203
more emphasis is placed on textile processing techniques to prepare the precursor materials for composite component manufacturing. Techniques such as commingling and powder coating, discussed in Section 8.3.2, account for high viscosity by minimising flow paths between the reinforcing fibres.
8.5.2 Thermoset materials The nature of thermoset materials involves chemical reactions with toxic substances that form cross-links upon curing. Thermoset polymers dominate in structural applications because of their high stiffness, strength and shape stability. Due to their low viscosity (which can be up to 100 000 times lower than those of some thermoplastics) they have little trouble flowing in between the network of fibre loops created by the knitting process. However, a major shortcoming of these materials is their limited recyclability and non-biodegradability.
8.5.3 Biodegradable materials Over the past ten to fifteen years a large number of biobased polymers have been developed and are now beginning to emerge as commercially viable replacements for commonly used consumer product polymers. However, to date, biopolymers have struggled to be price competitive with commodity polymers such as PE, PP and polystyrene. Relatively low yield rates and demand have kept manufacturing rates low and hence prices high. This has limited the use of biopolymers to niche products, such as bioresorbable implants and sutures in medical applications. However, increasing environmental awareness, improved yields and manufacturing processes, as well as new legislations have seen an increasing focus on the use of biopolymers for applications such as polymer bags, food packaging, nappies and cosmetic containers. Recently Sainsbury’s, a leading UK supermarket, announced that it would use biodegradable packaging for its house-brand foods and carrier bags. Cargill-Dow LLC, the company that produces the NatureWorks® range of PLA (Poly (lactic acid)) offers its high quality PLA product in various grades suitable for injection moulding, extrusion/thermoforming, film and blow moulding. In addition to price, the degree of biodegradability in polymers often has a detrimental effect on performance characteristics such as strength, flexibility and brittleness. Therefore, both price and performance have been key drivers in the move towards biopolymer-composites. Poly-β-hydroxyalkanoates (PHAs), PLAs and starch are commercially prevalent natural polymers that have been the focus of research into biopolymer composites. Table 8.2 presents some of the current commercially available PHAs, PLAs and starches (including blends) along with other synthetically produced biodegradable polymers and their manufacturers (Haugaard et al., 2001; Mohanty et al., 2000; Plackett and Vazquez, 2004; Johnson et al., 2003).
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
204 1 2 3 4
1 2 3 4 5 6 7 8 9 40 1 2 43X
Advances in knitting technology
Table 8.2 Biodegradable polymer materials currently available in the market (Haugaard et al., 2000; Mohanty et al., 2000; Plackett and Vazquez, 2004; Johnson et al., 2003) Polymer type
Manufacturer
Product name
Polyhydroxyalkanoates Metabolix, Inc. Biopol™, PHA Procter and Gamble Nodax™ Biomer Biomer™ Biomatera Inc. PHB Industrial S/A Cellulose acetate Courtaulds Mazzucchelli Bioceta Polylactides Cargill-Dow LLC NatureWorks™ Galactic SA Galactic Birmingham Polymers, Inc. Lactel, Absorbable Boehringer Ingelheim Resomer® Mitsubishi Plastics, Inc Ecoloju Mitsui LACEA PURAC Purasorb® Shimadzu Corporation Lacty Hycail Biomer Starches and starch blends VTT Chemical Technology Cohpol™ BIOTECH Gmbh Bioplast®, Bioflex®, Biopur® Novamont Mater-Bi Avebe Paragon Earth Shell Starch-based composite Bioplastic (Michigan) Envar™ Hayashibara Pullulan National Starch Eco-Foam® Groen Granulaat Ecoplast Rodenburg Biopolymers Solanyl Starch Tech RenEW, ST1, ST2, ST3 Supol Supol Vegemat Vegemat® Biop Biopar Biochemical Labs Other biodegradable polymers based wholly on synthetics Copolyester BASF Ecoflex Eastmen Chemical Eastar Bio Union Carbide Tone polymer Solvay CAPA Showa Bionolle Polycaprolactone Highpolymer Bayer BAK Polybutylene succinate Bayer MHP 9029 Bayer Degranil VPSP42002 Polyesteramide Fortum Polyesterurethane Dupont Biomax Polyester co-polymer Polylactic acid Polyester
© Woodhead Publishing Limited, 2011
Knitted fabric composites
205
For biopolymer materials such as PLA, applications in apparel, bedding, furniture, carpet and personal care products are already on the market, which shows that there are no limitations to textile processing. The next logical step is the development of these materials for composite applications.
8.6
Developments in manufacturing methods for knitted fabric composites
8.6.1 Manufacturing methods Sheet forming Composite component forming from solid composite sheets is perhaps the most commonly used method of production for thermoplastic composite parts (Bhattacharyya, 1997). It is also possible to use thermoset composite materials in the case of short fibre reinforcement, or uncured or partially cured materials such as those prepared in sheet moulding compound (SMC). Common sheet forming techniques are variations on a theme involving matching rigid moulds, a single mould/rubber punch or single mould/flexible membrane plus pressure (air or hydraulic) and vacuum pressure. In the case of knitted fabric composites, not all of these forming techniques are suitable due to the material’s geometrical characteristics. Out-of-plane undulations resulting from knit-loop formation give rise to high compaction ratios (10:1) in order to achieve an adequately consolidated composite component of reasonable thickness. If layers of the material are stacked in the same orientation, then nesting helps to alleviate this problem; however, for complete knit geometries (unlike MWKs discussed in Section 4.1), it is difficult to achieve fibre volume fractions greater than 60%. If the material is prepared as a sheet or plate prior to component forming then it tends to reinflate upon reheating due to the bending stresses present in the stiff reinforcing fibres. This can also pose a problem with regard to surface finish unless rigid tooling (mould) is used. Stretch forming To help avoid wrinkling during the forming process, knitted fabric preform sheets can be stretch-formed. By clamping the perimeter of the sheets, the material is restricted from flange draw-in and stretched into the shape of the mould. The process makes excellent use of the strain transmission properties of knit geometries, and highly stretched areas inherently result in aligned fibres giving higher stiffness and strength. Draping Perhaps the most suitable forming method for knitted composite materials is the draping of flat sheets over a male or female mould. Although this is quite a
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
206 1 2 3 4 5 6 7
Advances in knitting technology
labour-intensive process, wrinkling can be avoided manually and the shape of the component is determined before closing the mould. Integral knitting Integral knitting is where the near-net shape of the final composite component is manufactured on the knitting machine and subsequently used as the preform for the component to be produced. The added advantages are low material wastage and labour costs (Savci and Curiskis, 1997). With present day knitting machinery such as Shima-Seiki’s ‘wholegarment’ flat bed knitting machines, it is possible to produce gaugeless (loops of any size) and seamless three-dimensional preforms directly by specifying the geometry using KnitCAD data. The manufacturing process is illustrated in Fig. 8.5; the only post forming manufacturing procedure that may be required is part trimming – however, this can also be incorporated into the tooling.
8.6.2 Influences of forming method Knitted fabric composite components are best produced by the draping or stretching of a flat 2D preform, or the draping of a 3D shape as is shown in Fig. 8.5. One of the questions that has arisen during the study of knitted composites is: does stretching actually improve the mechanical properties? In the work performed by Putnoki et al. (1999), composite specimens made from weft knitted
1 2 3 4 5 6 7 8 9 40 1 2 43X
8.5 Forming of 2D and 3D commingled knitted fabric thermoplastic composite preforms.
© Woodhead Publishing Limited, 2011
Knitted fabric composites
207
1 × 1 rib glass fibre and poly(ethylene terephthalate) Twintex® commingled yarn, were stretched in the wale direction to various degrees before consolidation. Their results showed that the mechanical properties in the stretching direction were enhanced, while in the transverse direction the properties were reduced. Therefore, the work highlighted that the material would exhibit an increase in anisotropy due to the stretching and contracting of the wale and course directions. Another interesting observation was that the transverse impact toughness remained constant since an increase in strength was accompanied by a reduced ability for deformation. Overall, it was shown that rather than improving the mechanical properties of the material, stretching during forming provides a means of redirecting strength and stiffness in the directions that may be required by the component during manufacture. Since their inception, research on commingled thermoplastic composites has become popular with researchers concentrating on optimising forming parameters such as forming rate, temperature, pressure and consolidation time to minimise void content, cycle time and to maximise quality (Long et al., 2001; Bernet et al., 2001). With commingled yarn, there are again two options for forming the composite: i) the compaction of the commingled fabric to the required thickness and subsequent heating/consolidation within the mould or ii) external heating and transfer into a cold tool for forming and consolidation. Of course, the second option is more practical these days as quick in-mould heating techniques are currently unavailable. However, technologies such as radio frequency heating such as that used in the plywood industry could change that. In the work by Long et al. (2001) it has been found that heating commingled preform with no application of pressure can result in migration of the constituents, increasing the potential for void formation. The causes of the migration were described as being induced by the shrinkage of polypropylene upon heating, which tends to coalesce within and between the yarns. It is stated that the problem of migration can also be caused by differences in the constituent fibre sizes. In the case of fabrics, this effect coupled with the yarn crossover forces bring about the migration of the smaller diameter fibres towards the contact point. Therefore, an ideal process might be one where the yarn contains equally sized fibres and migration during consolidation is controlled by precompaction.
8.7
Mechanical properties
Of all the textile geometries, knitted fabrics are the most difficult to study due to their complex geometric structures. The shape of knitted structures is determined by their geometric parameters along with the elastic forces (determined by the material properties of the fibres) attempting to unravel the yarn back to its original unstressed state. In other words, the shape of a knitted loop is not based purely on geometric parameters but is a force-determined geometry (Hearle, 1969). For knitted fabric composites, the mechanical properties of the composite are
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
208 1 2 3 4 5 6 7 8 9
Advances in knitting technology
influenced by the ‘frozen state’ geometric structure of the reinforcement. During the forming stages, the deformation behaviour of the fabric changes the knit geometry in order to allow shaping of the part. Once the composite material has cooled or cured, the geometry of the reinforcement is locked in place. Therefore, in order to obtain the true geometry of the knitted fabric composite reinforcement, consideration of the deformations that take place during fabric formation is necessary before considering the deformation during composite forming. With these ideas in mind, Duhovic and Bhattacharyya created a numerical simulation capable of generating tensile specimens of any type of weft-knitted structure (Duhovic and Bhattacharyya, 2006). The model could also be modified to cover warp-knitted structures. The simulation manufactured and predicted the mechanics of a 1 × 1 rib fabric specimen by numerically knitting a five-needle specimen, then subjecting it to a tensile test. Once the validity of the model was demonstrated, it was used to investigate the deformation mechanisms of the particular knit structure in terms of energy contributions. The model has implications for the study of the many aspects of knitted fabric composites including fabric permeability and forming property prediction. It can also be used to study the mechanics of the many types of knitted fabrics quantatively. A selection of images from the work is shown in Figure 8.6.
8.8
Applications
8.8.1 Automotive, aerospace
1 2 3 4 5 6 7 8 9 40 1 2 43X
Potential automotive applications for knitted fabric composites include bumper bars, floor panels and door members (Bannister, 2004). In fact, Van Vuure and Ko (2003) describe the extensive use of knitted fabric composites (MWKs and nearnet shaped knits) for an all-composite electric vehicle in development by Solectria Inc. In this project MWKs are used in the top shell and floor pan of the vehicle, while the wheel wells make use of near net shaped knitted preforms. Other examples in the automotive industry include body panels and interior components for train structures (Miravete, 1999). In the aerospace sector, net-shaped knitted composites have been used to manufacture components such as rudder-tip fairings (structures that reduce drag) for passenger aircraft, helicopter door-track pockets and midsized aircraft radomes (Chou and Ko, 1989).
8.8.2 Consumer items, sports equipment Helmets for a multitude of applications, boot toecap protectors, shin pads and other forms of body armour, and medical prostheses are all examples of consumer level applications for knitted fabric composites. Non-rigid applications must also not be forgotten: these include gloves and other types of protective garments.
© Woodhead Publishing Limited, 2011
Knitted fabric composites
209
8.6 Simulating the behaviour of knitted fabric composites (Duhovic and Bhattacharyya, 2006).
8.9
Conclusion
Knitted fabric composites are one of the many types of textile structural composite used in the composites industry. They fit neatly into the broad family of FRP structures where medium strength, stiffness and excellent processability are required. The high performance fibres used for these materials range from E-glass and carbon aramid to high strength polymer fibres, and even some selected high strength natural fibres. These fibres are knitted into the preform fabric for the composite, and a variety of thermoset, thermoplastic and even biodegradable polymer materials can be used as the matrix. Preimpregnated materials are also available, although knitted
© Woodhead Publishing Limited, 2011
1 2 3 4 5 6 7 8 9 10 1 2 3 4 5 6 7 8 9 20 1 2 3 4 5 6 7 8 9 30 1 2 3 4 5 6 7 8 9 40 1 2 43X
210 1 2 3 4 5 6
Advances in knitting technology
structures are not as common as weaves. The most commonly used knit structure is the multiaxial warp knit because of its ability to meet the demands of primary load bearing applications. Forming methods for knitted fabric composites include sheet forming and draping. In the case of sheet forming, stretching can be applied to obtain desired mechanical properties, while for draping, integral shapes can be produced to minimise material wastage and eliminate cutting. Due to their complex geometric structures the mechanical properties of knitted fabric composites are not easily predicted. However, simulations to generate and examine the behaviour of these structures have been carried out. Knitted fabric composites have found applications in automotive components as well as consumer level items such as helmets, toecap protectors and medical prostheses.
8.10 Acknowledgements The authors would like to thank the Foundation for Research Science and Technology (FRST) New Zealand, for their financial support.
8.11 References
1 2 3 4 5 6 7 8 9 40 1 2 43X
Astrom, B. T. (1997), Manufacturing of Polymer Composites, London, UK, Chapman & Hall. Bannister, M. K. (2004), Development and application of advanced textile composites, Proc. Instn Mech. Engrs: J. Materials: Design and Applications, 218(L), 253–260. doi:10.1243/1464420041