David J. Whitehouse University of Warwick Coventry, UK
Boca Raton London New York
CRC Press is an imprint of the Tayl...
89 downloads
1791 Views
27MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
David J. Whitehouse University of Warwick Coventry, UK
Boca Raton London New York
CRC Press is an imprint of the Taylor & Francis Group, an informa business
A TA Y L O R & F R A N C I S B O O K
CRC Press Taylor & Francis Group 6000 Broken Sound Parkway NW, Suite 300 Boca Raton, FL 33487-2742 © 2011 by Taylor and Francis Group, LLC CRC Press is an imprint of Taylor & Francis Group, an Informa business No claim to original U.S. Government works Printed in the United States of America on acid-free paper 10 9 8 7 6 5 4 3 2 1 International Standard Book Number: 978-1-4200-8201-2 (Hardback) This book contains information obtained from authentic and highly regarded sources. Reasonable efforts have been made to publish reliable data and information, but the author and publisher cannot assume responsibility for the validity of all materials or the consequences of their use. The authors and publishers have attempted to trace the copyright holders of all material reproduced in this publication and apologize to copyright holders if permission to publish in this form has not been obtained. If any copyright material has not been acknowledged please write and let us know so we may rectify in any future reprint. Except as permitted under U.S. Copyright Law, no part of this book may be reprinted, reproduced, transmitted, or utilized in any form by any electronic, mechanical, or other means, now known or hereafter invented, including photocopying, microfilming, and recording, or in any information storage or retrieval system, without written permission from the publishers. For permission to photocopy or use material electronically from this work, please access www.copyright.com (http://www.copyright.com/) or contact the Copyright Clearance Center, Inc. (CCC), 222 Rosewood Drive, Danvers, MA 01923, 978-750-8400. CCC is a not-for-profit organization that provides licenses and registration for a variety of users. For organizations that have been granted a photocopy license by the CCC, a separate system of payment has been arranged. Trademark Notice: Product or corporate names may be trademarks or registered trademarks, and are used only for identification and explanation without intent to infringe. Library of Congress Cataloging-in-Publication Data Whitehouse, D. J. (David J.) Handbook of surface and nanometrology / by David J. Whitehouse. -- 2nd ed. p. cm. Rev. ed. of: Handbook of surface metrology. c1994. Includes bibliographical references and index. ISBN 978-1-4200-8201-2 1. Surfaces (Technology)--Measurement. I. Whitehouse, D. J. (David J.). Handbook of surface metrology. II. Title. TA418.7.W47 2011 620’.440287--dc22 Visit the Taylor & Francis Web site at http://www.taylorandfrancis.com and the CRC Press Web site at http://www.crcpress.com
2010014776
This book is dedicated to my wife Ruth who has steered me through many computer problems, mainly of my own making, and cajoled, encouraged, and threatened me in equal measure to carry on when my willpower flagged.
Contents Preface........................................................................................................................................................................................xxi Acknowledgments.....................................................................................................................................................................xxiii Chapter 1. Introduction—Surface and Nanometrology............................................................................................................. 1 1.1 1.2 1.3 1.4 1.5
General.......................................................................................................................................................... 1 Surface Metrology......................................................................................................................................... 1 Background to Surface Metrology................................................................................................................ 1 Nanometrology.............................................................................................................................................. 2 Book Structure............................................................................................................................................... 2
Chapter 2. Characterization....................................................................................................................................................... 5 2.1 2.2
2.3 2.4
The Nature of Surfaces.................................................................................................................................. 5 Surface Geometry Assessment and Parameters............................................................................................ 7 2.2.1 General—Roughness Review.......................................................................................................... 7 2.2.1.1 Profile Parameters (ISO 25178 Part 2 and 4278).............................................................. 9 2.2.1.2 Reference Lines.............................................................................................................. 16 2.2.1.3 Filtering Methods for Surface Metrology....................................................................... 21 2.2.1.4 Morphological Filtering.................................................................................................. 34 2.2.1.5 Intrinsic Filtering............................................................................................................ 41 2.2.1.6 Summary........................................................................................................................ 41 2.2.2 Statistical Parameters and Random Process Analysis of Surface Roughness............................... 41 2.2.2.1 General........................................................................................................................... 41 2.2.2.2 Amplitude Probability Density Function........................................................................ 42 2.2.2.3 Random Process Analysis Applied to Surfaces............................................................. 44 2.2.2.4 Areal Texture Parameters, Isotropy and Lay (Continuous)............................................ 59 2.2.2.5 Discrete Characterization............................................................................................... 65 2.2.2.6 Assessment of Isotropy and Lay..................................................................................... 68 2.2.3 Methods of Characterization Using Amplitude Information......................................................... 71 2.2.3.1 Amplitude and Hybrid Parameters................................................................................. 71 2.2.3.2 Skew and Kurtosis.......................................................................................................... 71 2.2.3.3 Beta Function.................................................................................................................. 71 2.2.3.4 Fourier Characteristic Function...................................................................................... 72 2.2.3.5 Chebychev Function and Log Normal€Function............................................................ 73 2.2.3.6 Variations on Material Ratio Curve╯+╯Evaluation Procedures....................................... 74 2.2.4 Characterization Using Lateral Spatial Information...................................................................... 79 2.2.4.1 Time Series Analysis Methods of Characterization....................................................... 79 2.2.4.2 Transform Methods Based on Fourier............................................................................ 81 2.2.4.3 Space–Frequency Transforms........................................................................................ 82 2.2.4.4 Fractals........................................................................................................................... 93 2.2.5 Surface Texture and Non-Linear Dynamics.................................................................................. 98 2.2.5.1 Poincare Model and Chaos............................................................................................. 98 2.2.5.2 Stochastic Resonance...................................................................................................... 99 Waviness.................................................................................................................................................... 100 Errors of Form........................................................................................................................................... 106 2.4.1 Introduction.................................................................................................................................. 106 2.4.2 Straightness and Related Topics................................................................................................... 107 2.4.2.1 ISO /TS 12780-1, 2003, Vocabulary and Parameters of Straightness and 12780-2, 2003, Specification Operators, Give the International Standard Position Regarding Straightness and Its Measurement.............................................................. 107 2.4.2.2 Generalized Probe Configurations............................................................................... 108 2.4.2.3 Assessments and Classification.................................................................................... 109 v
vi
Contents
2.4.3
Flatness..........................................................................................................................................110 2.4.3.1 ISO /TS 12781-1,2003, Vocabulary and Parameters of Flatness and ISO/TS 12781-2, 2003, Specification Operators Give the International Standards Position on Flatness.....................................................................................................................110 2.4.3.2 General..........................................................................................................................110 2.4.3.3 Assessment....................................................................................................................111 2.4.4 Roundness.....................................................................................................................................114 2.4.4.1 ISO/TS 12181-1, 2003, Vocabulary and Parameters and ISO/TS 12181-2, 2003, Specification Operators Give the International Standards Current Position on Roundness....................................................................114 2.4.4.2 General..........................................................................................................................114 2.4.4.3 Measurement and Characterization...............................................................................115 2.4.4.4 General Comments on Radial, Diametral, and Angular Variations............................ 124 2.4.4.5 Roundness Assessment................................................................................................. 126 2.4.4.6 Roundness Filtering and Other Topics......................................................................... 133 2.4.4.7 Roundness Assessment Using Intrinsic Datum............................................................ 135 2.4.4.8 Eccentricity and Concentricity..................................................................................... 138 2.4.4.9 Squareness.................................................................................................................... 139 2.4.4.10 Curvature Assessment Measurement from Roundness Data....................................... 139 2.4.4.11 Radial Slope Estimation............................................................................................... 144 2.4.4.12 Assessment of Ovality and Other Shapes..................................................................... 145 2.4.5 Three-Dimensional Shape Assessment........................................................................................ 146 2.4.5.1 Sphericity...................................................................................................................... 146 2.4.6 Cylindricity and Conicity............................................................................................................. 150 2.4.6.1 Standards ISO/TS 1280-1, 2003, Vocabulary and Parameters of Cylindrical Form, ISO/TS 1280-2, 2003, Specification Operators................................................. 150 2.4.6.2 General......................................................................................................................... 150 2.4.6.3 Methods of Specifying Cylindricity............................................................................. 151 2.4.6.4 Reference Figures for Cylinder Measurement.............................................................. 156 2.4.6.5 Conicity......................................................................................................................... 160 2.4.7 Complex Surfaces..........................................................................................................................161 2.4.7.1 Aspherics.......................................................................................................................161 2.4.7.2 Free-Form Geometry.....................................................................................................161 2.5 Characterization of Defects on the Surface............................................................................................... 164 2.5.1 General ISO 8785 Surface Defects.............................................................................................. 164 2.5.2 Dimensional Characteristics of Defects....................................................................................... 165 2.5.3 Type Shapes of Defect.................................................................................................................. 165 2.6 Discussion.................................................................................................................................................. 165 References............................................................................................................................................................ 167 Chapter 3. Processing, Operations, and Simulations..............................................................................................................171 Comment...............................................................................................................................................................171 3.1 Digital Methods..........................................................................................................................................171 3.1.1 Sampling........................................................................................................................................171 3.1.2 Quantization..................................................................................................................................173 3.1.3 Effect of Computer Word Length..................................................................................................174 3.1.4 Numerical Analysis—The Digital Model.....................................................................................175 3.1.4.1 Differentiation...............................................................................................................175 3.1.4.2 Integration......................................................................................................................176 3.1.4.3 Interpolation and Extrapolation.....................................................................................176 3.2 Discrete (Digital) Properties of Random Surfaces.................................................................................... 177 3.2.1 Some Numerical Problems Encountered in Surface Metrology.................................................. 177 3.2.2 Definitions of a Peak and Density of Peaks................................................................................. 177 3.2.3 Effect of Quantization on Peak Parameters..................................................................................178 3.2.4 Effect of Numerical Analysis on Peak Parameters.......................................................................178
vii
Contents
3.2.5 3.2.6
3.3
3.4
3.5 3.6
3.7
Effect of Sample Interval on the Peak Density Value.................................................................. 180 Digital Evaluation of Other Profile Peak Parameters.................................................................. 182 3.2.6.1 Peak Height Measurement............................................................................................ 182 3.2.6.2 Peak Curvature............................................................................................................. 183 3.2.6.3 Profile Slopes................................................................................................................ 184 3.2.7 Summary of Profile Digital Analysis Problems........................................................................... 186 3.2.8 Areal (3D) Filtering and Parameters............................................................................................ 186 3.2.9 Digital Areal (3D) Measurement of Surface Roughness Parameters........................................... 188 3.2.9.1 General......................................................................................................................... 188 3.2.9.2 The Expected Summit Density and the Distributions of Summit Height and Curvature...................................................................................................................... 189 3.2.9.3 The Effect of the Sample Interval and Limiting Results.............................................. 190 3.2.10 Patterns of Sampling and Their Effect on Discrete Properties (Comparison of Three-, Four-, Five- and Seven-Point Analysis of Surfaces)..................................................................... 192 3.2.10.1 Four-Point Sampling Scheme in a Plane...................................................................... 192 3.2.10.2 The Hexagonal Grid in the Trigonal Symmetry Case.................................................. 193 3.2.10.3 The Effect of Sampling Interval and Limiting Results on Sample Patterns............................................................................................................ 195 3.2.11 Discussion.................................................................................................................................... 198 Digital Form of Statistical Analysis Parameters....................................................................................... 199 3.3.1 Amplitude Probability Density Function..................................................................................... 199 3.3.2 Moments of the Amplitude Probability Density Function........................................................... 201 3.3.3 Autocorrelation Function............................................................................................................. 201 3.3.4 Autocorrelation Measurement Using the Fast Fourier Transform............................................... 202 3.3.5 Power Spectral Density................................................................................................................ 202 Digital Estimation of Reference Lines for Surface Metrology................................................................. 203 3.4.1 General......................................................................................................................................... 203 3.4.2 Convolution Filtering................................................................................................................... 204 3.4.2.1 Repeated Convolutions................................................................................................. 205 3.4.3 Box Functions............................................................................................................................... 206 3.4.4 Effect of Truncation..................................................................................................................... 207 3.4.5 Alternative Methods of Computation........................................................................................... 208 3.4.5.1 Overlap Methods.......................................................................................................... 208 3.4.5.2 Equal-Weight Methods................................................................................................. 208 3.4.6 Recursive Filters........................................................................................................................... 209 3.4.6.1 The Discrete Transfer Function.................................................................................... 209 3.4.6.2 An Example...................................................................................................................211 3.4.7 Use of the Fast Fourier Transform in Surface Metrology Filtering............................................. 212 3.4.7.1 Areal Case.................................................................................................................... 212 Examples of Numerical Problems In Straightness and Flatness............................................................... 213 Algorithms..................................................................................................................................................214 3.6.1 Differences between Surface and Dimensional Metrology and Related Subjects........................214 3.6.1.1 Least-Squares Evaluation of Geometric Elements........................................................214 3.6.1.2 Optimization................................................................................................................. 215 3.6.1.3 Linear Least Squares.................................................................................................... 215 3.6.1.4 Eigenvectors and Singular Value Decomposition........................................................ 215 3.6.2 Best-Fit Shapes............................................................................................................................. 215 3.6.2.1 Planes............................................................................................................................ 215 3.6.2.2 Circles and Spheres........................................................................................................216 3.6.2.3 Cylinders and Cones......................................................................................................217 3.6.3 Other Methods.............................................................................................................................. 221 3.6.3.1 Minimum Zone Method............................................................................................... 221 3.6.3.2 Minimax Methods—Constrained Optimization.......................................................... 221 3.6.3.3 Simplex Methods.......................................................................................................... 222 Basic Concepts In Linear Programing...................................................................................................... 223 3.7.1 General......................................................................................................................................... 223
viii
Contents
3.7.2
Dual Linear Programs in Surface Metrology.............................................................................. 223 3.7.2.1 Minimum Radius Circumscribing Limaçon................................................................ 224 3.7.3 Minimum Zone, Straight Lines, and Planes................................................................................ 225 3.7.4 Minimax Problems....................................................................................................................... 227 3.7.4.1 General Algorithmic Approach.................................................................................... 227 3.7.4.2 Definitions.................................................................................................................... 227 3.8 Fourier Transforms and the Fast Fourier Transform................................................................................. 228 3.8.1 General Properties........................................................................................................................ 228 3.8.2 Fast Fourier Transform................................................................................................................. 229 3.8.2.1 Analytic Form............................................................................................................... 229 3.8.2.2 Practical Realization..................................................................................................... 231 3.8.3 General Considerations of Properties.......................................................................................... 232 3.8.3.1 Fourier Series of Real Data.......................................................................................... 233 3.8.4 Applications of Fourier Transforms in Surface Metrology.......................................................... 233 3.8.4.1 Fourier Transform for Non-Recursive Filtering........................................................... 233 3.8.4.2 Power Spectral Analysis............................................................................................... 234 3.8.4.3 Correlation.................................................................................................................... 234 3.8.4.4 Other Convolutions....................................................................................................... 234 3.8.4.5 Interpolation................................................................................................................. 234 3.8.4.6 Other Analysis in Roughness....................................................................................... 234 3.8.4.7 Roundness Analysis...................................................................................................... 234 3.9 Transformations In Surface Metrology..................................................................................................... 235 3.9.1 General......................................................................................................................................... 235 3.9.2 Hartley Transform........................................................................................................................ 235 3.9.3 Walsh Functions–Square Wave Functions–Hadamard................................................................ 236 3.10 Space–Frequency Functions...................................................................................................................... 237 3.10.1 General......................................................................................................................................... 237 3.10.2 Ambiguity Function..................................................................................................................... 237 3.10.3 Discrete Ambiguity Function (DAF)........................................................................................... 238 3.10.3.1 Discrete Ambiguity Function Computation................................................................. 238 3.10.4 Wigner Distribution Function W (x, ω)........................................................................................ 239 3.10.4.1 Properties...................................................................................................................... 239 3.10.4.2 Analytic Signals............................................................................................................ 239 3.10.4.3 Moments....................................................................................................................... 239 3.10.4.4 Digital Wigner Distribution Applied to Surfaces......................................................... 240 3.10.4.5 Examples of Wigner Distribution: Application to Signals—Waviness........................ 241 3.10.5 Comparison of the Fourier Transform, the Ambiguity Function, and the Wigner Distribution................................................................................................................................... 242 3.10.6 Gabor Transform.......................................................................................................................... 243 3.10.7 Wavelets in Surface Metrology.................................................................................................... 244 3.11 Surface Generation.................................................................................................................................... 244 3.11.1 Profile Generation........................................................................................................................ 244 3.11.2 Areal Surface Generation............................................................................................................. 246 3.12 Atomistic Considerations and Simulations............................................................................................... 248 3.12.1 General......................................................................................................................................... 248 3.12.1.1 Microscopic Mechanics................................................................................................ 248 3.12.1.2 Macroscopic Propagating Surfaces.............................................................................. 248 3.12.2 Mobile Cellular Automata MCA.................................................................................................. 249 3.12.3 Simulation Considerations........................................................................................................... 251 3.12.4 Molecular Dynamics.................................................................................................................... 251 3.13 Summary................................................................................................................................................... 252 References............................................................................................................................................................ 253
ix
Contents
Chapter 4. Measurement Techniques..................................................................................................................................... 255 4.1 4.2
4.3
Background................................................................................................................................................ 255 4.1.1 Some Early Dates of Importance in the Metrology and Production of Surfaces......................... 255 4.1.2 Specification................................................................................................................................. 257 Measurement Systems Stylus—Micro...................................................................................................... 257 4.2.1 The System................................................................................................................................... 257 4.2.1.1 Stylus Characteristics................................................................................................... 258 4.2.2 Tactile Considerations.................................................................................................................. 258 4.2.2.1 General......................................................................................................................... 258 4.2.2.2 Tip Dimension.............................................................................................................. 258 4.2.2.3 Stylus Angle.................................................................................................................. 260 4.2.2.4 Stylus Pressure-Static Case, Compliance, Stiffness, and Maximum Pressure............ 260 4.2.2.5 Elastic/Plastic Behavior................................................................................................ 261 4.2.2.6 Stylus and Skid Damage Prevention Index................................................................... 262 4.2.2.7 Pick-Up Dynamics and “Trackability”......................................................................... 263 4.2.2.8 Unwanted Resonances in Metrology Instruments........................................................ 265 4.2.2.9 Conclusions about Mechanical Pick-Ups of Instruments Using the Conventional Approach....................................................................................................................... 267 4.2.3 Relationship between Static and Dynamic Forces for Different Types of Surface...................... 268 4.2.3.1 Reaction due to Periodic Surface.................................................................................. 268 4.2.3.2 Reaction due to Random Surfaces................................................................................ 268 4.2.3.3 Statistical Properties of the Reaction and Their Significance: Autocorrelation Function and Power Spectrum of R(t)........................................................................... 269 4.2.3.4 System Properties and Their Relationship to the Surface: Damping and Energy Loss............................................................................................................................... 270 4.2.3.5 Integrated Damping: System Optimization for Random Surface................................ 270 4.2.3.6 Alternative Stylus Systems and Effect on Reaction/Random Surface......................... 271 4.2.3.7 Criteria for Scanning Surface Instruments................................................................... 272 4.2.3.8 Forms of the Pick-Up Equation.................................................................................... 272 4.2.4 Mode of Measurement................................................................................................................. 274 4.2.4.1 Topography Measurement............................................................................................ 274 4.2.4.2 Force Measurement...................................................................................................... 275 4.2.4.3 Open- and Closed-Loop Considerations...................................................................... 276 4.2.4.4 Spatial Domain Instruments......................................................................................... 277 4.2.5 Other Stylus Configurations......................................................................................................... 278 4.2.5.1 High-Speed Area Tracking Stylus (a Micro Equivalent of the Atomic Scanning Probe Family)............................................................................................................... 278 4.2.5.2 Multi-Function Stylus Systems..................................................................................... 279 4.2.5.3 Pick-Up and Transducer System................................................................................... 280 4.2.6 Metrology and Various Mechanical Issues.................................................................................. 281 4.2.6.1 Generation of Reference Surface.................................................................................. 282 4.2.6.2 Intrinsic Datum—Generation and Properties of the Skid Datum................................ 284 4.2.6.3 Stylus Instruments Where the Stylus Is Used as an Integrating Filter......................... 289 4.2.6.4 Space Limitations of “References” Used in Roundness Measurement........................ 290 4.2.7 Areal (3D) Mapping of Surfaces Using Stylus Methods.............................................................. 294 4.2.7.1 General Problem........................................................................................................... 294 4.2.7.2 Mapping........................................................................................................................ 295 4.2.7.3 Criteria for Areal Mapping........................................................................................... 295 4.2.7.4 Contour and Other Maps of Surfaces........................................................................... 301 Measuring Instruments Stylus—Nano/Atomic Scale............................................................................... 301 4.3.1 Scanning Probe Microscopes (SPM) [or (SXM) for Wider Variants]......................................... 301 4.3.1.1 History.......................................................................................................................... 301 4.3.1.2 Background................................................................................................................... 303
x
Contents
4.3.2
4.4
General Characteristics................................................................................................................ 304 4.3.2.1 The Tip.......................................................................................................................... 305 4.3.2.2 The Cantilever.............................................................................................................. 309 4.3.2.3 Simple Scanning Systems for SPM...............................................................................310 4.3.2.4 Traceability....................................................................................................................311 4.3.2.5 General Comments........................................................................................................311 4.3.2.6 Other Scanning Microscopes........................................................................................312 4.3.3 Operation and Theory of the Scanning Probe Microscope (SPM)...............................................313 4.3.3.1 Scanning Tunneling Microscope (STM).......................................................................313 4.3.3.2 The Atomic Force Microscope......................................................................................316 4.3.4 Interactions....................................................................................................................................318 4.3.4.1 Tip–Sample....................................................................................................................318 4.3.4.2 Cantilever—Sample (e.g., Tapping Mode).....................................................................319 Optical Techniques.................................................................................................................................... 322 4.4.1 General......................................................................................................................................... 322 4.4.1.1 Comparison between Stylus and Optical Methods....................................................... 322 4.4.1.2 Properties of the Focused Spot..................................................................................... 325 4.4.2 Optical Followers......................................................................................................................... 326 4.4.3 Hybrid Microscopes..................................................................................................................... 330 4.4.3.1 Confocal Microscopes.................................................................................................. 330 4.4.3.2 Near-Field Scanning Optical Microscopy (NSOM)..................................................... 333 4.4.3.3 Heterodyne Confocal Systems...................................................................................... 333 4.4.4 Oblique Angle Methods............................................................................................................... 335 4.4.5 Interference Methods................................................................................................................... 336 4.4.5.1 Phase Detection Systems.............................................................................................. 336 4.4.5.2 Spatial and Temporal Coherence.................................................................................. 336 4.4.5.3 Interferometry and Surface Metrology......................................................................... 336 4.4.5.4 Heterodyne Methods..................................................................................................... 340 4.4.5.5 Other Methods in Interferometry................................................................................. 342 4.4.5.6 White Light Interferometry—Short Coherence Interferometry................................... 343 4.4.5.7 White Light Interferometer—Thin Transparent Film Measurement........................... 346 4.4.5.8 Absolute Distance Methods with Multi-Wavelength Interferometry........................... 349 4.4.6 Moiré Methods..............................................................................................................................351 4.4.6.1 General..........................................................................................................................351 4.4.6.2 Strain Measurement...................................................................................................... 352 4.4.6.3 Moiré Contouring......................................................................................................... 352 4.4.6.4 Shadow Moiré............................................................................................................... 352 4.4.6.5 Projection Moiré........................................................................................................... 352 4.4.6.6 Summary...................................................................................................................... 353 4.4.7 Holographic Techniques............................................................................................................... 353 4.4.7.1 Introduction.................................................................................................................. 353 4.4.7.2 Computer Generated Holograms.................................................................................. 355 4.4.7.3 Conoscopic Holography................................................................................................ 356 4.4.7.4 Holographic Interferometry.......................................................................................... 357 4.4.8 Speckle Methods.......................................................................................................................... 357 4.4.9 Diffraction Methods..................................................................................................................... 365 4.4.9.1 General......................................................................................................................... 365 4.4.9.2 Powder and Chip Geometry......................................................................................... 372 4.4.9.3 Vector Theory............................................................................................................... 373 4.4.10 Scatterometers (Glossmeters)....................................................................................................... 373 4.4.11 Scanning and Miniaturization...................................................................................................... 377 4.4.11.1 Scanning System........................................................................................................... 377 4.4.11.2 Remote and Miniature System..................................................................................... 378 4.4.12 Flaw Detection by Optical Means................................................................................................ 380 4.4.12.1 General Note................................................................................................................. 380 4.4.12.2 Transform Plane Methods............................................................................................. 380
xi
Contents
4.4.12.3 Scanning for Flaws....................................................................................................... 382 4.4.12.4 “Whole-Field” Measurement........................................................................................ 383 4.4.13 Comparison of Optical and Stylus Trends................................................................................... 384 4.4.13.1 General Engineering Surface Metrology...................................................................... 384 4.4.13.2 General Optical Comparison........................................................................................ 385 4.5 Capacitance and Other Techniques........................................................................................................... 385 4.5.1 Areal Assessment......................................................................................................................... 385 4.5.2 Scanning Capacitative Microscopes............................................................................................ 386 4.5.3 Capacitance Proximity Gauge...................................................................................................... 387 4.5.4 Inductance.................................................................................................................................... 387 4.5.5 Impedance Technique—Skin Effect............................................................................................ 388 4.5.6 Other Methods.............................................................................................................................. 388 4.5.6.1 General......................................................................................................................... 388 4.5.6.2 Friction Devices............................................................................................................ 388 4.5.6.3 Liquid Methods............................................................................................................. 388 4.5.6.4 Pneumatic Methods...................................................................................................... 388 4.5.6.5 Thermal Method........................................................................................................... 389 4.5.6.6 Ultrasonics.................................................................................................................... 389 4.5.7 Summary...................................................................................................................................... 392 4.6 Electron Microscopy, Photon Microscopy, Raman Spectromertry........................................................... 392 4.6.1 General......................................................................................................................................... 392 4.6.2 Scanning Electron Microscope (SEM)........................................................................................ 394 4.6.3 Energy Dispersive X-Ray Spectrometer....................................................................................... 397 4.6.4 Transmission Electron Microscope (TEM)................................................................................. 397 4.6.5 Photon Tunneling Microscopy (PTM)......................................................................................... 399 4.6.6 Raman Spectroscopy.................................................................................................................... 400 4.7 Comparison of Techniques—General Summary...................................................................................... 401 4.8 Some Design Considerations..................................................................................................................... 403 4.8.1 Design Criteria for Instrumentation............................................................................................. 403 4.8.2 Kinematics................................................................................................................................... 404 4.8.3 Pseudo-Kinematic Design............................................................................................................ 406 4.8.4 Mobility........................................................................................................................................ 407 4.8.5 Linear Hinge Mechanisms........................................................................................................... 407 4.8.6 Angular Motion Flexures............................................................................................................. 409 4.8.7 Force and Measurement Loops.....................................................................................................410 4.8.7.1 Metrology Loop.............................................................................................................410 4.8.8 Instrument Capability Improvement.............................................................................................412 4.8.9 Alignment Errors..........................................................................................................................413 4.8.10 Abbé Errors...................................................................................................................................414 4.8.11 Other Mechanical Considerations.................................................................................................415 4.8.12 Systematic Errors and Non-Linearities.........................................................................................415 4.8.13 Material Selection.........................................................................................................................416 4.8.14 Noise..............................................................................................................................................417 4.8.14.1 Noise Position............................................................................................................... 420 4.8.14.2 Probe System Possibilities............................................................................................ 420 4.8.14.3 Instrument Electrical and Electronic Noise.................................................................. 420 4.8.15 Replication.................................................................................................................................... 421 References............................................................................................................................................................ 422 Chapter 5. Standardization–Traceability–Uncertainty.......................................................................................................... 429 5.1 5.2 5.3
Introduction............................................................................................................................................... 429 Nature of Errors......................................................................................................................................... 429 5.2.1 Systematic Errors......................................................................................................................... 429 5.2.2 Random Errors............................................................................................................................. 430 Deterministic Or Systematic Error Model................................................................................................ 430 5.3.1 Sensitivity..................................................................................................................................... 430
xii
Contents
5.3.2 Readability................................................................................................................................... 430 5.3.3 Calibration.................................................................................................................................... 430 5.4 Basic Components of Accuracy Evaluation.............................................................................................. 430 5.4.1 Factors Affecting the Calibration Standard................................................................................. 430 5.4.2 Factors Affecting the Workpiece................................................................................................. 430 5.4.3 Factors Affecting the Person........................................................................................................ 430 5.4.4 Factors Affecting the Environment.............................................................................................. 430 5.4.5 Classification of Calibration Standards.........................................................................................431 5.4.6 Calibration Chain..........................................................................................................................431 5.4.7 Time Checks to Carry Out Procedure..........................................................................................431 5.5 Basic Error Theory for a System................................................................................................................431 5.6 Propagation of Errors................................................................................................................................ 432 5.6.1 Deterministic Errors..................................................................................................................... 432 5.6.2 Random Errors............................................................................................................................. 432 5.7 Some Useful Statistical Tests for Surface Metrology................................................................................ 433 5.7.1 Confidence Intervals for Any Parameter...................................................................................... 433 5.7.2 Tests for The Mean Value of a Surface—The Student t Test....................................................... 434 5.7.3 Tests for The Standard Deviation—The χ2 Test........................................................................... 435 5.7.4 Goodness of Fit............................................................................................................................ 435 5.7.5 Tests for Variance—The F Test.................................................................................................... 435 5.7.6 Tests of Measurements against Limits—16% Rule...................................................................... 435 5.7.7 Measurement of Relevance—Factorial Design............................................................................ 436 5.7.7.1 The Design.................................................................................................................... 436 5.7.7.2 The Interactions............................................................................................................ 437 5.7.8 Lines of Regression...................................................................................................................... 438 5.7.9 Methods of Discrimination.......................................................................................................... 438 5.8 Uncertainty in Instruments—Calibration in General............................................................................... 439 5.9 Calibration of Stylus Instruments.............................................................................................................. 440 5.9.1 Stylus Calibration......................................................................................................................... 441 5.9.1.1 Cleaning........................................................................................................................ 441 5.9.1.2 Use of Microscopes...................................................................................................... 441 5.9.1.3 Use of Artifacts............................................................................................................. 442 5.9.1.4 Stylus Force Measurement............................................................................................ 443 5.9.2 Calibration of Vertical Amplification for Standard Instruments................................................. 444 5.9.2.1 Gauge Block Method.................................................................................................... 444 5.9.2.2 Reason’s Lever Arm..................................................................................................... 444 5.9.2.3 Sine Bar Method........................................................................................................... 444 5.9.2.4 Accuracy Considerations.............................................................................................. 445 5.9.2.5 Comparison between Stylus and Optical Step Height Measurement for Standard Instruments.................................................................................................... 445 5.9.3 Some Practical Standards (Artifacts) and ISO Equivalents......................................................... 447 5.9.3.1 Workshop Standards..................................................................................................... 447 5.9.3.2 ISO Standards for Instrument Calibration.................................................................... 447 5.9.4 Calibration of Transmission Characteristics (Temporal Standards)............................................ 450 5.9.5 Filter Calibration Standards......................................................................................................... 452 5.9.6 Step Height for Ultra Precision and Scanning Probe Microscopes............................................. 454 5.9.7 X-Ray Methods—Step Height..................................................................................................... 454 5.9.8 X-Rays—Angle Measurement..................................................................................................... 457 5.9.9 Traceability and Uncertainties of Nanoscale Surface Instrument “Metrological” Instruments.......................................................................................................... 458 5.9.9.1 M 3 NIST Instrument..................................................................................................... 459 5.9.9.2 Uncertainties General and Nanosurf IV NPL.............................................................. 459 5.10 Calibration of Form Instruments............................................................................................................... 462 5.10.1 Magnitude.................................................................................................................................... 462 5.10.1.1 Magnitude of Diametral Change for Tilted Cylinder................................................... 462 5.10.1.2 Shafts and Holes Engaged by a Sharp Stylus............................................................... 463
xiii
Contents
5.10.1.3 Shaft Engaged by a Hatchet.......................................................................................... 463 5.10.1.4 Hole Engaged by a Hatchet........................................................................................... 463 5.10.2 Separation of Errors—Calibration of Roundness and Form....................................................... 463 5.10.3 General Errors due to Motion...................................................................................................... 467 5.10.3.1 Radial Motion............................................................................................................... 468 5.10.3.2 Face Motion.................................................................................................................. 468 5.10.3.3 Error Motion—General Case....................................................................................... 468 5.10.3.4 Fundamental and Residual Error Motion..................................................................... 469 5.10.3.5 Error Motion versus Run-Out (or TIR)......................................................................... 470 5.10.3.6 Fixed Sensitive Direction Measurements..................................................................... 470 5.10.3.7 Considerations on the Use of the Two-Gauge-Head System for a Fixed Sensitive Direction........................................................................................................ 470 5.10.3.8 Other Radial Error Methods......................................................................................... 471 5.11 Variability of Surface Parameters............................................................................................................. 472 5.12 Gps System—International and National Standards................................................................................ 474 5.12.1 General......................................................................................................................................... 474 5.12.2 Geometrical Product Specification (GPS).................................................................................... 475 5.12.3 Chain of Standards within the GPS............................................................................................. 475 5.12.3.1 Explanation................................................................................................................... 475 5.12.3.2 Specifics within Typical Box........................................................................................ 476 5.12.3.3 Position in Matrix......................................................................................................... 477 5.12.3.4 Proposed Extension to Matrix...................................................................................... 478 5.12.3.5 Duality Principle........................................................................................................... 480 5.12.4 Surface Standardization—Background....................................................................................... 480 5.12.5 Role of Technical Specification Documents................................................................................ 482 5.12.6 Selected List of International Standards Applicable to Surface Roughness Measurement: Methods; Parameters; Instruments; Comparison Specimens...................................................... 483 5.12.7 International Standards (Equivalents, Identicals, and Similars)..................................................... 483 5.12.8 Category Theory in the Use of Standards and Other Specifications in Manufacture, in General, and in Surface Texture, in Particular............................................................................. 485 5.13 Specification on Drawings......................................................................................................................... 486 5.13.1 Surface Roughness....................................................................................................................... 486 5.13.2 Indications Generally—Multiple Symbols................................................................................... 486 5.13.3 Reading the Symbols.................................................................................................................... 487 5.13.4 General and Other Points............................................................................................................. 487 5.14 Summary................................................................................................................................................... 487 References............................................................................................................................................................ 489 Chapter 6. Surfaces and Manufacture.................................................................................................................................... 493 6.1 6.2 6.3
Introduction............................................................................................................................................... 493 Manufacturing Processes.......................................................................................................................... 493 6.2.1 General......................................................................................................................................... 493 Cutting....................................................................................................................................................... 493 6.3.1 Turning......................................................................................................................................... 493 6.3.1.1 General......................................................................................................................... 493 6.3.1.2 Finish Machining.......................................................................................................... 494 6.3.1.3 Effect of Tool Geometry—Theoretical Surface Finish................................................ 495 6.3.1.4 Other Surface Roughness Effects in Finish Machining............................................... 499 6.3.1.5 Tool Wear...................................................................................................................... 500 6.3.1.6 Chip Formation............................................................................................................. 501 6.3.2 Diamond Turning......................................................................................................................... 501 6.3.3 Milling and Broaching................................................................................................................. 502 6.3.3.1 General......................................................................................................................... 502 6.3.3.2 Surface Roughness....................................................................................................... 503
xiv
Contents
6.3.4
6.4
6.5
6.6
6.7
Dry Cutting.................................................................................................................................. 505 6.3.4.1 General......................................................................................................................... 505 6.3.4.2 Cutting Mechanisms..................................................................................................... 505 Abrasive Processes.................................................................................................................................... 508 6.4.1 General......................................................................................................................................... 508 6.4.2 Types of Grinding.........................................................................................................................511 6.4.3 Comments on Grinding................................................................................................................ 512 6.4.3.1 Nature of the Grinding Process.................................................................................... 512 6.4.4 Centerless Grinding .....................................................................................................................513 6.4.4.1 General..........................................................................................................................513 6.4.4.2 Important Parameters for Roughness and Roundness...................................................513 6.4.4.3 Roundness Considerations . ..........................................................................................514 6.4.5 Cylindrical Grinding.................................................................................................................... 515 6.4.5.1 Spark-Out...................................................................................................................... 515 6.4.5.2 Elastic Effects................................................................................................................516 6.4.6 Texture Generated in Grinding.....................................................................................................516 6.4.6.1 Chatter...........................................................................................................................517 6.4.7 Other Types of Grinding...............................................................................................................518 6.4.7.1 Comments on Grinding.................................................................................................519 6.4.7.2 Slow Grinding................................................................................................................519 6.4.8 Theoretical Comments on Roughness and Grinding................................................................... 520 6.4.9 Honing.......................................................................................................................................... 523 6.4.10 Polishing and Lapping.................................................................................................................. 524 Unconventional Processes......................................................................................................................... 525 6.5.1 General......................................................................................................................................... 525 6.5.2 Ultrasonic Machining................................................................................................................... 526 6.5.3 Magnetic Float Polishing............................................................................................................. 527 6.5.4 Physical and Chemical Machining............................................................................................... 527 6.5.4.1 Electrochemical Machining (ECM)............................................................................. 527 6.5.4.2 Electrolytic Grinding.................................................................................................... 528 6.5.4.3 Electrodischarge Machining (EDM)............................................................................ 528 Forming Processes.................................................................................................................................... 528 6.6.1 General......................................................................................................................................... 528 6.6.2 Surface Texture and the Plastic Deformation Processes.............................................................. 529 6.6.3 Friction and Surface Texture in Material Movement....................................................................531 6.6.4 Ballizing....................................................................................................................................... 532 Effect of Scale of Size in Manufacture: Macro to Nano to Atomic Processes......................................... 532 6.7.1 General......................................................................................................................................... 532 6.7.2 Nanocutting.................................................................................................................................. 533 6.7.2.1 Mechanism of Nanocutting.......................................................................................... 533 6.7.3 Nanomilling................................................................................................................................. 533 6.7.3.1 Scaling Experiments..................................................................................................... 534 6.7.3.2 General Ball Nose Milling........................................................................................... 536 6.7.3.3 Surface Finish............................................................................................................... 537 6.7.4 Nanofinishing by Grinding.......................................................................................................... 538 6.7.4.1 Comments on Nanogrinding........................................................................................ 538 6.7.4.2 Brittle Materials and Ductile Grinding........................................................................ 540 6.7.5 Micropolishing............................................................................................................................. 542 6.7.5.1 Elastic Emission Machining......................................................................................... 542 6.7.5.2 Mechanical–Chemical Machining............................................................................... 543 6.7.6 Microforming............................................................................................................................... 544 6.7.7 Three Dimensional Micromachining........................................................................................... 545 6.7.8 Atomic-Scale Machining............................................................................................................. 546 6.7.8.1 General......................................................................................................................... 546 6.7.8.2 Electron Beam Methods............................................................................................... 546 6.7.8.3 Ion Beam Machining.................................................................................................... 547
Contents
xv
6.7.8.4 Focused Ion Beam—String and Level Set Approach................................................... 550 6.7.8.5 Collimated (Shower) Methods—Ion and Electron Beam Techniques..........................551 6.7.8.6 General Comment on Atomic-Type Processes............................................................. 552 6.7.8.7 Molecular Beam Epitaxy.............................................................................................. 552 6.8 Structured Surface Manufacture............................................................................................................... 553 6.8.1 Distinction between Conventional and Structured Surfaces........................................................ 553 6.8.2 Structured Surfaces Definitions................................................................................................... 554 6.8.3 Macro Examples........................................................................................................................... 555 6.8.4 Micromachining of Structured Surfaces...................................................................................... 558 6.8.4.1 General......................................................................................................................... 558 6.8.4.2 Some Specific Methods of Micro-Machining Structured Surfaces............................. 558 6.8.4.3 Hard Milling/Diamond Machining.............................................................................. 559 6.8.4.4 Machining Restriction Classification........................................................................... 560 6.8.4.5 Diamond Micro Chiseling............................................................................................ 561 6.8.4.6 Other Factors Including Roughness Scaling................................................................ 563 6.8.4.7 Polishing of Micromolds.............................................................................................. 564 6.8.5 Energy Assisted Micromachining................................................................................................ 565 6.8.5.1 Radiation-Texturing Lasers.......................................................................................... 565 6.8.5.2 Ion Beam Microtexturing............................................................................................. 567 6.8.6 Some Other Methods of Micro and Nanostructuring.................................................................. 568 6.8.6.1 Hierarchical Structuring............................................................................................... 568 6.8.6.2 Plasma Structuring....................................................................................................... 569 6.8.7 Structuring of Micro-Lens Arrays............................................................................................... 569 6.8.7.1 General Theory............................................................................................................. 569 6.8.7.2 Mother Lens Issues....................................................................................................... 571 6.8.7.3 Typical Fabrication of Microarrays.............................................................................. 572 6.8.7.4 Fabrication of Micro Arrays—All Liquid Method....................................................... 572 6.8.8 Pattern Transfer—Use of Stamps................................................................................................. 573 6.8.9 Self Assembly of Structured Components, Bio Assembly........................................................... 575 6.8.10 Chemical Production of Shapes and Forms-Fractals................................................................... 577 6.8.11 Anisotropic Chemical Etching of Material for Structure............................................................ 579 6.8.12 Use of Microscopes for Structuring Surfaces.............................................................................. 580 6.8.13 General Nano-Scale Patterning.................................................................................................... 583 6.9 Manufacture of Free-Form Surfaces......................................................................................................... 583 6.9.1 Optical Complex Surfaces............................................................................................................ 583 6.9.2 Ball End Milling.......................................................................................................................... 583 6.9.3 Micro End-Milling....................................................................................................................... 586 6.9.4 Free Form Polishing..................................................................................................................... 587 6.9.5 Hybrid Example........................................................................................................................... 589 6.10 Mathematical Processing of Manufacture-Finite Element Analysis (Fe), Md, Nurbs.............................. 590 6.10.1 General......................................................................................................................................... 590 6.10.2 Finite Element Analysis (FE)....................................................................................................... 590 6.10.3 Molecular Dynamics.................................................................................................................... 590 6.10.4 Multi-Scale Dynamics.................................................................................................................. 591 6.10.5 NURBS........................................................................................................................................ 593 6.11 The Subsurface and the Interface.............................................................................................................. 594 6.11.1 General......................................................................................................................................... 594 6.11.2 Brittle/Ductile Transition in Nano-Metric Machining................................................................. 595 6.11.3 Kinematic Considerations............................................................................................................ 596 6.12 Surface Integrity........................................................................................................................................ 596 6.12.1 Surface Effects Resulting from the Machining Process.............................................................. 596 6.12.2 Surface Alterations....................................................................................................................... 597 6.12.3 Residual Stress............................................................................................................................. 597 6.12.3.1 General......................................................................................................................... 597 6.12.3.2 Grinding........................................................................................................................ 599 6.12.3.3 Turning......................................................................................................................... 601
xvi
Contents
6.12.3.4 Milling.......................................................................................................................... 603 6.12.3.5 Shaping......................................................................................................................... 603 6.12.3.6 General Comment......................................................................................................... 603 6.12.4 Measurement of Stresses.............................................................................................................. 605 6.12.4.1 General......................................................................................................................... 605 6.12.4.2 Indirect Methods........................................................................................................... 605 6.12.4.3 Direct Methods............................................................................................................. 606 6.12.5 Subsurface Properties Influencing Function................................................................................ 607 6.12.5.1 General......................................................................................................................... 607 6.12.5.2 Influences of Residual Stress........................................................................................ 607 6.13 Surface Geometry—A Fingerprint of Manufacture.................................................................................. 609 6.13.1 General......................................................................................................................................... 609 6.13.2 Use of Random Process Analysis..................................................................................................610 6.13.2.1 Single-Point-Cutting Turned Parts................................................................................610 6.13.2.2 Abrasive Machining.......................................................................................................612 6.13.3 Spacefrequency Functions (the Wigner Distribution)...................................................................613 6.13.4 Application of Wavelet Function...................................................................................................614 6.13.5 Non-Linear Dynamicschaos Theory.............................................................................................616 6.13.6 Application of Non-Linear Dynamics—Stochastic Resonance....................................................619 6.14 Surface Finish Effects In Manufacture of Microchip Electronic Components........................................ 620 6.15 Discussion and Conclusions...................................................................................................................... 622 References............................................................................................................................................................ 622 Chapter 7. Surface Geometry and Its Importance in Function.............................................................................................. 629 7.1
7.2
7.3
Introduction............................................................................................................................................... 629 7.1.1 The Function Map........................................................................................................................ 629 7.1.1.1 Summary of the “Function Map” Concept................................................................... 630 7.1.1.2 Chapter Objective and Function of the Concept Map.................................................. 631 7.1.2 Nature of Interaction.................................................................................................................... 632 Two-Body Interaction—The Static Situation............................................................................................ 633 7.2.1 Contact......................................................................................................................................... 633 7.2.1.1 Point Contact................................................................................................................ 635 7.2.2 Macroscopic Behavior.................................................................................................................. 635 7.2.2.1 Two Spheres in Contact................................................................................................ 636 7.2.2.2 Two Cylinders in Contact............................................................................................. 637 7.2.2.3 Crossed Cylinders at Any Angle.................................................................................. 638 7.2.2.4 Sphere on a Cylinder.................................................................................................... 638 7.2.2.5 Sphere inside a Cylinder............................................................................................... 638 7.2.3 Microscopic Behavior.................................................................................................................. 638 7.2.3.1 General......................................................................................................................... 638 7.2.3.2 Elastic Contact.............................................................................................................. 642 7.2.3.3 Elastic/Plastic Balance—Plasticity Index.................................................................... 663 7.2.3.4 Size and Surface Effects on Mechanical and Material Properties............................... 675 7.2.4 Functional Properties of Normal Contact.................................................................................... 678 7.2.4.1 General......................................................................................................................... 678 7.2.4.2 Stiffness........................................................................................................................ 679 7.2.4.3 Normal Contact Other Phenomena—Creep and Seals................................................ 682 7.2.4.4 Adhesion....................................................................................................................... 684 7.2.4.5 Thermal Conductivity................................................................................................... 689 Two-Body Interactions—Dynamic Behavior............................................................................................ 694 7.3.1 General......................................................................................................................................... 694 7.3.2 Friction......................................................................................................................................... 695 7.3.2.1 Friction Mechanisms—General................................................................................... 695 7.3.2.2 Friction Modeling in Simulation.................................................................................. 696
xvii
Contents
7.4
7.5
7.3.2.3 Dry Friction.................................................................................................................. 702 7.3.2.4 Wet Friction—Clutch Application................................................................................ 705 7.3.2.5 Atomistic Considerations—Simulations...................................................................... 706 7.3.2.6 Rubber Friction and Surface Effects............................................................................ 709 7.3.2.7 Other Applications and Considerations.........................................................................710 7.3.2.8 Thermo-Mechanical Effects of Friction Caused by Surface Interaction..................... 712 7.3.2.9 Friction and Wear Comments–Dry Conditions............................................................ 715 7.3.3 Wear—General............................................................................................................................ 715 7.3.3.1 Wear Classification........................................................................................................716 7.3.3.2 Wear Measurement from Surface Profilometry............................................................717 7.3.3.3 Wear Prediction Models................................................................................................718 7.3.3.4 Abrasive Wear and Surface Roughness........................................................................ 720 7.3.4 Lubrication—Description of the Various Types with Emphasis on the Effect of Surfaces......... 722 7.3.4.1 General......................................................................................................................... 722 7.3.4.2 Hydrodynamic Lubrication and Surface Geometry..................................................... 722 7.3.4.3 Two Body Lubrication under Pressure: Elasto Hydrodynamic Lubrication and the Influence of Roughness................................................................................................. 733 7.3.4.4 Mixed Lubrication and Roughness............................................................................... 743 7.3.4.5 Boundary Lubrication................................................................................................... 743 7.3.4.6 Nanolubrication—A Summary..................................................................................... 748 7.3.5 Surface Geometry Modification for Function.............................................................................. 749 7.3.5.1 Texturing and Lubrication............................................................................................ 749 7.3.5.2 Micro Flow and Shape of Channels............................................................................. 754 7.3.5.3 Shakedown, Surface Texture, and Running In............................................................. 755 7.3.6 Surface Failure Modes................................................................................................................. 760 7.3.6.1 The Function–Lifetime, Weibull Distribution.............................................................. 760 7.3.6.2 Scuffing Problem...........................................................................................................761 7.3.6.3 Rolling Fatigue (Pitting and Spalling) Problem........................................................... 762 7.3.6.4 3D Body Motion and Geometric Implications............................................................. 764 7.3.7 Vibration Effects.......................................................................................................................... 769 7.3.7.1 Dynamic Effects—Change of Radius.......................................................................... 769 7.3.7.2 Normal Impact of Rough Surfaces............................................................................... 770 7.3.7.3 Squeeze Films and Roughness..................................................................................... 772 7.3.7.4 Fretting and Fretting Fatigue, Failure Mode................................................................ 776 One-Body Interactions.............................................................................................................................. 778 7.4.1 General Mechanical Electical Chemical...................................................................................... 778 7.4.1.1 Fatigue.......................................................................................................................... 778 7.4.1.2 Corrosion...................................................................................................................... 783 7.4.2 One Body with Radiation (Optical): The Effect of Roughness on the Scattering of Electromagnetic and Other Radiation.......................................................................................... 786 7.4.2.1 Optical Scatter—General............................................................................................. 786 7.4.2.2 General Optical Approach............................................................................................ 787 7.4.2.3 Scatter from Deterministic Surfaces............................................................................ 791 7.4.2.4 Summary of Results, Scalar and Geometrical Treatments.......................................... 792 7.4.2.5 Mixtures of Two Random Surfaces.............................................................................. 793 7.4.2.6 Other Considerations on Light Scatter......................................................................... 794 7.4.2.7 Scattering from Non-Gaussian Surfaces and Other Effects......................................... 800 7.4.2.8 Aspherics and Free Form Surfaces............................................................................... 804 7.4.3 Scattering by Different Sorts of Waves........................................................................................ 805 7.4.3.1 General......................................................................................................................... 805 7.4.3.2 Scattering from Particles and the Influence of Roughness........................................... 807 7.4.3.3 Thin Films—Influence of Roughness.......................................................................... 808 System Function Assembly....................................................................................................................... 809 7.5.1 Surface Geometry, Tolerances, and Fits....................................................................................... 809 7.5.1.1 Tolerances..................................................................................................................... 809
xviii
Contents
7.6
Discussion...................................................................................................................................................811 7.6.1 Profile Parameters........................................................................................................................ 812 7.6.2 Areal (3D) Parameters.................................................................................................................. 815 7.6.2.1 Comments on Areal Parameters................................................................................... 815 7.6.3 Amplitude and Spacing Parameters............................................................................................. 815 7.6.4 Comments on Textured Surface Properties..................................................................................816 7.6.5 Function Maps and Surfaces.........................................................................................................817 7.6.6 Systems Approach.........................................................................................................................819 7.6.7 Scale of Size and Miniaturization Effects of Roughness............................................................. 822 7.7 Conclusions................................................................................................................................................ 825 References............................................................................................................................................................ 826 Chapter 8. Surface Geometry, Scale of Size Effects, Nanometrology.................................................................................. 837 8.1 8.2
8.3
8.4
Introduction............................................................................................................................................... 837 8.1.1 Scope of Nanotechnology............................................................................................................ 837 8.1.2 Nanotechnology and Engineering................................................................................................ 837 Effect of Scale of Size on Surface Geometry............................................................................................ 838 8.2.1 Metrology at the Nanoscale.......................................................................................................... 838 8.2.1.1 Nanometrology............................................................................................................. 838 8.2.1.2 Nanometer Implications of Geometric Size................................................................. 839 8.2.1.3 Geometric Features and the Scale of Size.................................................................... 839 8.2.1.4 How Roughness Changes with Scale............................................................................ 839 8.2.1.5 Shape and (Scale of Size).............................................................................................. 841 8.2.1.6 General Comments Scale of Size Effects..................................................................... 843 Scale of Size, Surface Geometry, and Function........................................................................................ 845 8.3.1 Effects on Mechanical and Material Properties........................................................................... 845 8.3.1.1 Dynamic Considerations—Balance of Forces............................................................. 845 8.3.1.2 Overall Functional Dependence on Scale of Size........................................................ 846 8.3.1.3 Some Structural Effects of Scale of Size in Metrology................................................ 847 8.3.1.4 Nano-Physical Effects.................................................................................................. 848 8.3.1.5 Hierarchical Considerations......................................................................................... 850 8.3.2 Multiscale Effects—Nanoscale Affecting Macroscale................................................................ 851 8.3.2.1 Archard Legacy—Contact and Friction....................................................................... 851 8.3.2.2 Multiscale Surfaces....................................................................................................... 852 8.3.2.3 Langevin Properties...................................................................................................... 854 8.3.3 Molecular and Atomic Behavior.................................................................................................. 857 8.3.3.1 Micromechanics of Friction—Effect of Nanoscale Roughness—General Comments.....857 8.3.3.2 Micromechanics of Friction—Nanoscale Roughness.................................................. 857 8.3.3.3 Atomistic Considerations and Simulations................................................................... 859 8.3.3.4 Movable Cellular Automata (MCA)............................................................................. 859 8.3.4 Nano/Microshape and Function................................................................................................... 862 8.3.4.1 Microflow...................................................................................................................... 862 8.3.4.2 Boundary Lubrication................................................................................................... 862 8.3.4.3 Coatings........................................................................................................................ 864 8.3.4.4 Mechanical Properties of Thin Boundary Layer Films............................................... 865 8.3.5 Nano/Micro, Structured Surfaces and Elasto-Hydrodynamic Lubrication EHD........................ 867 8.3.5.1 Highly Loaded Non-Conformal Surfaces.................................................................... 867 8.3.5.2 Summary of Micro/Nano Texturing and Extreme Pressure Lubrication..................... 868 8.3.6 Nanosurfaces—Fractals............................................................................................................... 869 8.3.6.1 Wave Scatter Characteristics........................................................................................ 869 8.3.6.2 Fractal Slopes, Diffraction, Subfractal Model.............................................................. 871 Scale of Size and Surfaces in Manufacture............................................................................................... 872 8.4.1 Nano Manufacture—General...................................................................................................... 872 8.4.1.1 Requirements................................................................................................................ 872 8.4.1.2 Issues............................................................................................................................. 872 8.4.1.3 Solution......................................................................................................................... 872
xix
Contents
8.4.2
8.5
8.6
8.7
8.8
Nanomachinability....................................................................................................................... 872 8.4.2.1 Abrasive Methods......................................................................................................... 872 8.4.2.2 Alternative Abrasion with Chemical Action................................................................ 874 8.4.2.3 Nanocutting.................................................................................................................. 875 8.4.2.4 Micro/Nano-Ductile Methods Microforming and Scale of Size Dependence............. 876 8.4.3 Atomic-Scale Machining............................................................................................................. 878 8.4.3.1 General......................................................................................................................... 878 8.4.3.2 Atomic-Scale Processing.............................................................................................. 878 8.4.3.3 Electron Beam (EB) Methods....................................................................................... 879 8.4.3.4 Ion Beam Machining.................................................................................................... 879 8.4.3.5 General Comment on Atomic-Type Processes............................................................. 882 8.4.4 Chemical Production of Shapes and Forms................................................................................. 883 8.4.5 Use of Microscopes for Structuring Surfaces.............................................................................. 885 8.4.6 General Nanoscale Patterning...................................................................................................... 886 Nano Instrumentation................................................................................................................................ 887 8.5.1 Signal from Metrology Instruments as Function of Scale........................................................... 887 8.5.2 Instrument Trends—Resolution and Bandwidth.......................................................................... 887 8.5.3 Scanning Probe Microscopes (SPM), Principles, Design, and Problems.................................... 888 8.5.3.1 History.......................................................................................................................... 888 8.5.3.2 The Probe...................................................................................................................... 891 8.5.3.3 The Cantilever.............................................................................................................. 896 8.5.4 Interactions................................................................................................................................... 898 8.5.4.1 Tip–Sample Interface................................................................................................... 898 8.5.4.2 Cantilever—Sample Interaction (e.g., Tapping Mode)................................................. 900 8.5.5 Variants on AFM.......................................................................................................................... 902 8.5.5.1 General Problem........................................................................................................... 902 8.5.5.2 Noise............................................................................................................................. 903 8.5.5.3 Cantilever Constants..................................................................................................... 905 8.5.5.4 SPM Development........................................................................................................ 905 8.5.6 Electron Microscopy.................................................................................................................... 908 8.5.6.1 General......................................................................................................................... 908 8.5.6.2 Reaction of Electrons with Solids................................................................................. 909 8.5.6.3 Scanning Electron Microscope (SEM)......................................................................... 909 8.5.6.4 Transmission Electron Microscope (TEM)...................................................................911 8.5.7 Photon Interaction........................................................................................................................ 912 8.5.7.1 Scanning Near Field Optical Microscope (SNOM)..................................................... 912 8.5.7.2 Photon Tunneling Microscopy (PTM)......................................................................... 912 Operation and Design Considerations....................................................................................................... 913 8.6.1 General Comment on Nanometrology Measurement.................................................................. 913 8.6.2 The Metrological Situation........................................................................................................... 913 8.6.3 Some Prerequisites for Nanometrology Instruments................................................................... 913 Standards and Traceability........................................................................................................................ 915 8.7.1 Traceability................................................................................................................................... 915 8.7.2 Calibration.................................................................................................................................... 915 8.7.2.1 General......................................................................................................................... 915 8.7.2.2 Working Standards and Special Instruments................................................................916 8.7.2.3 Nano-Artifact Calibration—Some Probe and Detector Problems................................918 8.7.2.4 Dynamics of Surface Calibration at Nanometer Level................................................. 921 8.7.3 Comparison of Instruments: Atomic, Beam and Optical............................................................. 922 Measurement of Typical Nanofeatures...................................................................................................... 922 8.8.1 General......................................................................................................................................... 922 8.8.1.1 Thin Films.................................................................................................................... 922 8.8.2 Roughness.................................................................................................................................... 923 8.8.3 Some Interesting Cases................................................................................................................ 924 8.8.3.1 STM Moiré Fringes...................................................................................................... 924 8.8.3.2 Kelvin Probe Force Microscope (KPFM).................................................................... 925
xx
Contents
8.8.3.3 Electrostatic Force Microscope (EFM)........................................................................ 925 8.8.3.4 Atomic Force Microscope (Afm)—Nanoscale Metrology with Organic Specimens..................................................................................................................... 926 8.8.4 Extending the Range and Mode of Nano Measurement.............................................................. 928 8.8.4.1 Using Higher Frequencies............................................................................................ 928 8.8.4.2 Increasing the Range.................................................................................................... 929 8.9 Measuring Length to Nanoscale with Interferometers and Other Devices............................................... 930 8.9.1 Optical Methods........................................................................................................................... 930 8.9.1.1 Heterodyne.................................................................................................................... 930 8.9.2 Capacitative Methods................................................................................................................... 930 8.10 Nanogeometry in Macro Situations........................................................................................................... 932 8.10.1 Freeform Macro Geometry, Nanogeometry and Surface Structure............................................. 932 8.11 Discussion and Conclusions...................................................................................................................... 933 8.11.1 SPM Development........................................................................................................................ 933 8.11.2 Conclusion about Nanometrology................................................................................................ 933 References............................................................................................................................................................ 934 Chapter 9. General Comments............................................................................................................................................... 941 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9
Introduction............................................................................................................................................... 941 Characterization........................................................................................................................................ 941 Processing, Operations, and Simulations.................................................................................................. 942 Measurement Techniques.......................................................................................................................... 942 Traceability Standardization Uncertainty................................................................................................. 943 Surfaces and Manufacture......................................................................................................................... 943 Surface Geometry and Performance......................................................................................................... 944 Nanometrology.......................................................................................................................................... 944 Overview................................................................................................................................................... 945
Glossary.................................................................................................................................................................................... 947 Index.......................................................................................................................................................................................... 957
Preface There has been a shift in emphasis in surface and nanometrology since the first edition of this book was published. Previously it was considered acceptable to deal with miniaturization and nanotechnology separately from traditional surface geometry and its metrology, but this is no longer the case: the extent to which they are inextricably linked is now very clear. Nanoscale investigations on the molecular and sometimes atomic level are often fundamental to understanding and even controlling micro and macro behavior. Also, many macrosized objects have nanoscale detail and are made to nanoscale tolerances as in free-form applications. A principal objective of this book has been to determine how the reduction in scale of size from macro to nano has affected all aspects of surface use and manufacture as well as their measurement. This shift has extended through characterization, standardization, manufacture, and performance. So, instead of nanotechnology being reserved for one chapter as in the first edition, it now permeates Chapters 2 through 7. Chapter 8 collates the results. Although many of the original topics are preserved, they are approached with this change of emphasis in mind. This interdependence of scale has had profound practical implications because it is difficult and expensive to
carry out experiments encompassing more than one scale, with the result that the number of truly significant practical experiments is reducing and the number of simulations is increasing—dramatically, sometimes with detrimental effects. There is the danger that the physics of an experiment can get blurred. Also, recourse to common sense is sometimes not an option because of the shortfall in practical experience of the investigator, however enthusiastic he or she may be. Simulations do not provide an independent feedback. A new word coined here is “simpirical” which means the use of computer simulations to verify theory rather than using practical, empirical evidence. An aim of this edition, therefore, has been to point out, wherever appropriate, and clarify, if possible, extreme cases of this trend. There are many new challenges confronting the surface metrologist of today. New types of structured and free-form surface, changes in behavior with scale, the use of soft materials and new tools of characterization, as well as a new generation of atomic instrumentation, are spawning more problems than ever before. It is an exciting era in surface and nanometrology!
xxi
Acknowledgments I am grateful for the discussions I have had with Professors Xiang Jiang and Paul Scott of Huddersfield University’s Centre for Precision Technologies, UK, who have given me continual encouragement throughout the project. I list below, in no particular order, a number of people who have let me have comprehensive use of their figures, which has enhanced the publication considerably. There are authors of figures used in the manuscript who are not mentioned below. These are fully acknowledged in the text and referenced where appropriate in the figure captions. Professors Jiang and Scott from Huddersfield University, Professor R. Leach and Dr. Yacoot from the National Physical Laboratory, D. Mansfield of Taylor Hobson
(Ametek) Ltd., and Professor G. Smith formerly of the Southampton Institute, all from the UK. Drs. C. Evans and P. de Groot from Zygo Corporation and Jim Bryan from the USA. Dr. H. Haitjema of Mitutoyo Research Centre, Netherlands. Professor G. Goch from Bremen University, Germany, Professor G. Zhang of Tianjin University, PR China, and especially Professor E. Brinksmeier from Bremen University and Dr. B. Persson from IFF, FZ— Julich, from Germany. All opinions, suggestions, and conclusions in this book are entirely my own. While I have made every effort to be factually correct, if any errors have crept in, the fault is mine and I apologize.
xxiii
1 Introduction—Surface and Nanometrology 1.1 General As the title suggests this book is about surfaces and their measurement. This, in itself, is not a complete objective. There is little to be gained by just measurement unless it is for a purpose. So, the book also addresses the problems of why the surface is being measured, what needs to be identified and quantified and what is the effect of its manufacture. Not simply surfaces involved in general engineering are examined but increasingly surfaces at the nanometer level, in all covering a wide range of object sizes ranging from telescope mirrors down to molecular and atomic strcutures. Enough mathematics and physics are used to ensure that the book is comprehensive but hopefully not too much to muddy the issues. What the book does not do is to attempt to provide full details of applications or of manufacturing processes but only those related to the role and relevance of the surface.
1.2 SURFACE METROLOGY Surface metrology from an engineering standpoint is the measurement of the deviations of a workpiece from its intended shape, that is, from the shape specified on the drawing. It is taken to include features such as deviations from roundness, straightness, flatness, cylindricity, and so on. It also includes the measurement of the marks left on the workpiece in trying to get to the shape, i.e., the surface texture left by the machining process and also surface deviations on naturally formed objects. Surface metrology is essentially a mechanical engineering discipline but it will soon be obvious that as the subject has developed in recent years it has broadened out to include aspects of many other disciplines, and in particular that of nanotechnology in which it is now deeply interwoven. Perhaps the best way to place the role of engineering surface metrology is to consider just what needs to be measured in order to enable a workpiece to perform according to the designer’s aim. Assuming that the material has been specified correctly and that the workpiece has been made from it, the first thing to be done is to measure the dimensions. These will have been specified on the drawing to a tolerance. Under this heading is included the measurement of length, position, radius, and so on. So, dimensional metrology is the first aim because it ensures that the size of the workpiece conforms to the designer’s wish. This in turn ensures that the workpiece will assemble into an engine, gearbox, gyroscope or whatever; the static characteristics have therefore been satisfied.
This by itself is not sufficient to ensure that the workpiece will satisfy its function; it may not be able to turn or move, for example. This is where surface metrology becomes important. Surface metrology ensures that all aspects of the surface geometry are known and preferably controlled. If the shape and texture of the workpiece are correct then it will be able to move at the speeds, loads, and temperatures specified in the design; the dynamic characteristics have therefore been satisfied. The final group of measurements concerns the physical and chemical condition of the workpiece. This will be called here as physical metrology. It includes the hardness of the materials, both in the bulk and in the surface layers, and the residual stress of the surface, both in compression or in tension, left in the material by the machining process or the heat treatment. It also includes measurement of the metallurgical structure of the material, and its chemical construction. All these and more contribute to the durability of the component, for example, its resistance to corrosion or fatigue. Physical metrology therefore is the third major sector of engineering metrology: the long-term characteristics. As a general rule, all three types of measurement must take place in order to ensure that the workpiece will do its assigned job for the time specified; to guarantee its quality. This book, as mentioned earlier, is concerned specifically with surfaces but this does not necessarily exclude the other two. In fact it is impossible to divorce any of these disciplines completely from the others. After all, there is only one component and these measurements are all taken on it. Physical and chemical features of importance will be covered in some detail as and when they are necessary in the text.
1.3 Background to SURFACE METROLOGY Figure 1.1 shows where the block representing engineering surface metrology can be placed relative to blocks representing manufacture and function. In the block marked “manufacture” is included all aspects of the manufacturing process, such as machine performance, tool wear, and chatter, whereas in the block marked “function” is included all functional properties of the surfaces of components, such as the tribological regimes of friction, wear, and lubrication and other uses. The measurement block includes the measurement of roughness, roundness, and all other aspects of surface metrology. The figure shows that the texture and geometry of a workpiece can be important in two quite different applications: 1
2
Handbook of Surface and Nanometrology, Second Edition
Production engineer
Control
Measurement
Development design Optimize engineer Function
Manufacture
Quality control engineer
Satisfactory performance
FIGURE 1.1 Relationship of surface metrology.
one is concerned with controlling the manufacture (this is examined in detail in Chapter 6) and the other is concerned with the way in which the surface can influence how well a workpiece will function. Many of these uses fall under the title of tribology—the science of rubbing parts—but others include the effect of light on surfaces and also static contact. In fact the two blocks “manufacture” and “function” are not completely independent of each other, as illustrated by the line in the figure joining the two. Historically the correct function of the workpiece was guaranteed by controlling the manufacture. In practice, what happened was that a workpiece was made and tried out. If it functioned satisfactorily the same manufacturing conditions were used to make the next workpiece and so on for all subsequent workpieces. It soon became apparent that the control of the surface was being used as an effective go-gauge for the process and hence the function. Obviously what is required is a much more flexible and less remote way of guaranteeing functional performance; it should be possible, by measuring parameters of the surface geometry itself, to help to predict the function. The conventional way of ensuring performance is very much a balancing act and unfortunately the delicate equilibrium can be broken by changing the production process or even the measurement parameters. This may seem an obvious statement but within it lies one of the main causes for everyday problems in engineering. It will soon be made clear that deviations in surface geometry cannot simply be regarded as an irritant to be added to the general size measurement of a component. The smallness of geometric deviations does not infer smallness of importance. It will be shown that the surface geometry is absolutely critical in many applications and that it contains information that can be invaluable to a manufacturer if extracted correctly from the mass of data making up the surface. In almost every example of its use the criticism can be raised that the nature of the surface is not well understood and, even where it is, it is not properly specified especially on drawings. The importance of surface geometry should be recognized not just by the quality control engineer or inspector but also, more importantly, by the designer. It is he or she who should understand the influence that the surface has on behavior and
specify it accordingly. It is astonishing just how ill-informed most designers are where surface metrology is concerned. Many of them in fact consider that a “good” surface is necessarily a smooth one, the smoother the better. This is not only untrue, in many cases, it can be disastrous.
1.4 NanoMETROLOGY Since the first edition, the subject has developed in a number of ways. One is due to miniaturization which has brought out new situations in production techniques, inspection, and ways in which surfaces are employed as well as bringing in many new materials with their different properties. Miniaturization is much more than making things small. It is not just the size that has changed; the properties of materials change as well as the rules concerning static and dynamic behavior. At the nano and atomic scale the new generation of scanning microscopes have emerged and methods of investigating behavior on the atomic scale, such as molecular dynamics and mobile cellular automata are now being used. In fact the “scale of size” has a profound effect and has upset many preconceived beliefs in engineering and physics to such an extent that it has altered the content of every chapter in the book from that of the first edition. Another profound development has been due to the increasing use of computing in trying to understand and predict performance. Theoretical problems can be more readily solved and computer simulations to test theory as well as to examine methods of production are being used as a matter of course. These developments have meant that optimum shapes for performance can be explicitly worked out. This has resulted in the emergence of “free form” geometries and “structured surfaces,” which despite bringing tremendous gains in performance, in weight, amount of material, and size have also brought extra pressure on measurement and standardization, not to mention production processes. These new areas in technology do not mean that traditional metrology has stood still: there have been improvements over the whole spectrum of metrological activity, as will be seen.
1.5 book structure This new edition will report on progress in the traditional but vital subject areas as well as the new developments. A few comments will be made on each of the chapters to indicate some of the additions and other modifications that have been made. The format has in the chapters been revised to reflect a change in emphasis on the various subjects. In addition, there has been a limited amount of repetition in order to make the individual chapters to some extent self-contained. Chapter 2 starts by considering some of the simpler parameters and reference lines including splines and phasecorrected filters from the original concept to the now universal Gaussian version. The convolution filters are followed by morphological filters stemming from the old “E” system. Statistical parameters and functions follow together with their uses in manufacturing and performance (function). A
Introduction—Surface and Nanometrology
key approach looks at discrete random processes because this is how parameters are actually evaluated by instruments. Some aspects of areal (sometimes but wrongly termed 3D) parameter assessment are covered as well as some other functions including Wigner and wavelet to pull in space frequency effects. Fractal analysis and Weierstrass series are described to explain some aspects of scale of size problems. Chaotic properties of some surface signals are explored using stochastic resonance. Geometric form characterization is represented by roundness, cylindricity, etc. Finally, free form and aspherics are discussed. Chapter 3 discusses digital implementation of some of the concepts covered in Chapter 2 with emphasis on sampling patterns in areal random process analysis including areal Fourier analysis. The theoretical background to the digital evaluation of functional surface parameters is given. Computational geometry issues are discussed with particular reference to cylindricity and conicity. Some aspects of surface behavior at the nanometer level are considered using molecular dynamics and mobile cellular automata. Chapter 4 examines first the basic properties of stylus instruments with emphasis on dynamic measurement of different forms of surface revealing different criteria than for the traditional but rare sine-wave. The generation and philosophy of references are considered and then it is shown how the new scanning probe microscopes (SPM) resemble and differ from conventional stylus instruments. The modes of operation are explained and some time is spent on looking at the variants. The vexed problem of stylus-surface and cantilever-surface interaction is discussed from a number of viewpoints. One of the biggest sections in this chapter is devoted to optical methods ranging from optical probes mimicking the mechanical stylus to whole field assessment via conformal microscopy, moiré methods, interferometry, holography, speckle, and diffraction ending the optical section with flaw detection. Thin film measurement is dealt with at some length in the subsection on white light interferometry. This is followed by some other general methods such as capacitance and ultrasonic techniques. Electron microscopy, photon microscopy, and Raman spectroscopy and their relationship to the various other techniques are discussed, but some fundamental problems associated with presenting the comparative performance of instruments are revealed. To complete the chapter, some fundamental design issues are presented which is more of a check list for aspiring instrument designers. Because of their fundamental relevance, the nature of errors, error propagation, and traceability are considered early on in Chapter 5. These are followed by statistical testing and the design of test experiments. Uncertainty in instruments is explored with reference to some instruments. A lot of emphasis is placed in this chapter on the GPS (Geometric product specification) system which is being advocated throughout the world. The chain of standards, the role of the technical specification documents, and a selected list of standards are contained in the chapter together with some comments on the new concept of categorization. As in Chapter 4 the problem of surface–tip interaction and its meaning has to be included
3
in this chapter because of its central position in the traceability of SPM instruments and in the validity of the term “Fully traceable metrology instrument.” In Chapter 6 the basic processes are discussed with respect to the surfaces produced. Some aspects of the effect of the tool and workpiece materials, tool wear, chip formation, and lubrication on the surfaces are considered. Dry cutting in milling is singled out for discussion. Normal abrasive methods such as grinding, honing, and polishing are discussed as well as some issues in unconventional machining like ultrasonic machining, magnetic float polishing, ECM, EDM, and forming. A large section is devoted to the effects of the scale of size on the machining process covering, such subjects as nanocutting, nano-milling, nano-finishing by grinding. Physical effects and transitions from brittle to ductile machining at the nanoscale are considered in detail. This continues with micro forming and the atomic scale machining with electron beams, ion beams focused and collimated and finishes up with some detail on molecular beam epitaxy, etc. Another major section is devoted to the generation of structured surfaces starting with some old examples and then progressing through to the most modern techniques such as diamond micro chiseling, and the properties and geometry of surfaces generated in this way as well as the problems in measuring them. Micro fabrication of arrays is covered along with mother lens problems and there is a large section on the use of laser and other energy beam ways of structuring surfaces, mentioning various surface problems that can result from using these techniques. Self-assembly is discussed as well as bio assembly. In the section on the manufacture of free-form surfaces, optical free-form complex surfaces are considered first followed by methods of achievement using ball-end milling. Polishing methods are also given with examples. Mathematical processing is explained with some emphasis on multi-scale dynamics and molecular dynamics touching on finite element analysis. Surface integrity is not forgotten and some discussion on the residual stress implications of the processes and how to measure them is included. The section concludes with a breakdown of how the surface geometry can be used as a fingerprint of manufacture bringing in some aspects of chaos theory and stochastic resonance. Chapter 7 is the biggest chapter covering recent developments in the functional importance of surfaces starting with static two body interactions. There have been considerable developments by Persson in the deformation and contact mechanics of very elastic bodies using the unlikely mathematics of diffusion which are extensively covered, together with a comparison with existing theories mainly due to Greenwood. Alternative ways of presenting the results are considered. Scale of size issues are prominent in these discussions bringing in fractal considerations and the use of Weierstrass characterization linking back to Archard. How these new issues relate to the functional contact problems of stiffness, creep, adhesion, electrical, and thermal conductivity are discussed
4
Handbook of Surface and Nanometrology, Second Edition
at length. Plastic and dynamic effects including wet and dry friction bringing in the atomistic work of Popov using mobile cellular automata and how they differ from the macro-scale are discussed. Wear and wear prediction models are investigated. The influence of roughness and waviness on traditional lubrication regimes are compared with those using structured surfaces. Also considered is the influence of roughness on micro flow. Some examples are given. Other dynamic effects in the text are vibration, squeeze film generation, fretting, fretting fatigue, and various aspects of corrosion. Single-body effects, particularly the influence of surfaces and their structure on the scatter of light are reviewed including the various scattering elastic and inelastic modes, e.g., Rayleigh and Raman. Aspects of assembly, tolerancing, and the movement of very small micro parts are considered revealing some interesting scale of size effects including a Langevin engineering equivalent of Brownian movement in molecules. Nanotechnology and nanometrology form the main subjects in Chapter 8. This starts with an evaluation of the effect of the scale of size on surface metrology showing how roughness values change disproportionately with size and how shapes and even definitions have to be reconsidered as sizes shrink. How the balance of forces change with scale and how this results in completely different physical and material properties of nanotubes, nanowires, and nanoparticles when compared with their micro and macro equivalents. Considerations of scale on behavior are integrated by bringing together the results of previous chapters. Issues with the
development of the SPM and how they relate to other instruments are investigated in depth showing some concern with aspects of surface interaction and traceability. Often there are situations where there is a mixture of scales of size in which nanoscale features are superimposed on macroscopic objects. These situations pose some special problems in instrumentation. Cases involving nanostructure and roughness on large free-form bodies are particularly demanding. Some examples are given of telescopes and prosthetic knee joints energy conversion. Where appropriate, throughout the chapter some discussion of biological implications is given. Quantum effects are included in the atomistic sections. The book’s conclusions are summarized in Chapter 9 together with questions and answers to some of the issues raised throughout the book. Finally there is a glossary which gives the meaning of many key words and expressions used throughout the book as understood by the author. Copious references are provided throughout the book to enable the reader to pursue the subject further. Throughout the book it has been the intention to preserve the thread from the historical background of the subjects through to recent developments. This approach is considered to be absolutely essential to bring some sort of balance between the use of computing and, in particular, the use of simulations and packages and the fundamental “feel” for the subject. Simulation loses the independent input given by a practical input: the historical thread helps to put some of it back as well as adding to the interest.
2 Characterization 2.1 THE NATURE OF SURFACES Surface characterization, the nature of surfaces and the measurement of surfaces cannot be separated from each other. A deeper understanding of the surface geometry produced by better instrumentation often produces a new approach to characterization. Surface characterization is taken to mean the breakdown of the surface geometry into basic components based usually on some functional requirement. These components can have various shapes, scales of size, distribution in space, and can be constrained by a multiplicity of boundaries in height and position. Issues like the establishment of reference lines can be viewed from their ability to separate geometrical features or merely as a statement of the limit of instrument capability. Often one consideration determines the other! Ease of measurement can influence the perceived importance of a parameter or feature. It is difficult to ascribe meaningful significance to something which has not been or cannot be measured. One dilemma is always whether a feature of the surface is fundamental or simply a number which has been ascribed to the surface by an instrument. This is an uncertainty which runs right through surface metrology and is becoming even more obvious now that atomic scales of size are being explored. Surface, interface, and nanometrology are merging. For this reason what follows necessarily reflects the somewhat disjointed jumps in understanding brought on by improvements in measurement techniques. There are no correct answers. There is only a progressively better understanding of surfaces brought about usually by an improvement in measurement technique. This extra understanding enables more knowledge to be built up about how surfaces are produced and how they perform. This chapter therefore is concerned with the nature of the geometric features, the signal which results from the measuring instrument, the characterization of this signal, and its assessment. The nature of the signal obtained from the surface by an instrument is also considered in this chapter. How the measured signal differs from the properties of the surface itself will be investigated. Details of the methods used to assess the signal will also be considered but not the actual data processing. This is examined in Chapter 3. There is, however, a certain amount of overlap which is inevitable. Also, there is some attention paid to the theory behind the instrument used to measure the surface. This provides the link with Chapter 4. What is set down here follows what actually happened in practice. This approach has merit because it underlies the problems which first came to the attention of engineers in the early 1940s and 1950s. That it was subsequently modified to reflect more sophisticated requirements does not make it wrong; it simply allows a more complete picture to be drawn up. It also shows how characterization and measurement are inextricably
entwined, as are surface metrology and nanometrology, as seen in all chapters but especially in Chapter 8. It is tempting to start a description of practical surfaces by expressing all of the surface geometry in terms of departures from the desired three-dimensional shape, for example departures from an ideal cylinder or sphere. However, this presents problems, so rather than do this it is more convenient and simpler to start off by describing some of the types of geometric deviation which do occur. It is then appropriate to show how these deviations are assessed relative to some of the elemental shapes found in engineering such as the line or circle. Then, from these basic units, a complete picture can be subsequently built up. This approach has two advantages. First, some of the analytical tools required will be explained in a simple context and, second, this train of events actually happened historically in engineering. Three widely recognized causes of deviation can be identified:
1. The irregularities known as roughness that often result from the manufacturing process. Examples are (a) the tool mark left on the surface as a result of turning and (b) the impression left by grinding or polishing. Machining at the nanoscale still has process marks. 2. Irregularities, called waviness, of a longer wavelength caused by improper manufacture. An example of this might be the effects caused by a vibration between the workpiece and a grinding wheel. It should be noted here that by far the largest influence of waviness is in the roundness of the workpiece rather than in the deviations along the axis consequently what is measured as waviness along the axis is in fact only a component of the radial waviness which is revealed by the roundness profile. 3. Very long waves referred to as errors of form caused by errors in slideways, in rotating members of the machine, or in thermal distortion.
Often the first two are lumped together under the general expression of surface texture, and some definitions incorporate all three! Some surfaces have one, two or all of these irregularities [1]. Figure 2.1a, shows roughness and waviness superimposed on the nominal shape of a surface. A question often asked is whether these three geometrical features should be assessed together or separately. This is a complicated question with a complicated answer. One thing is clear; it is not just a question of geometry. The manufacturing factors which result in waviness, for instance, are different from those that produce roughness or form error. The 5
6
Handbook of Surface and Nanometrology, Second Edition
(a)
Waviness
Roughness
Nominal shape (b)
Roughness
(i) Subsurface plastic damage caused by roughness
Waviness
Subsurface elastic effects caused by waviness (ii)
Roughness
(c)
Geometric amplitude
Energy into surface
Waviness
λ
Roughness
Waviness
λ
Deformation Waviness effect Elastic deformation Roughness effect Plastic deformation µ
FIGURE 2.1 (a) Geometric deviations from intended shape, (b) energy wavelength spectrum, and (c) deformation mode wavelength spectrum.
effect of these factors is not restricted to producing an identifiable geometrical feature, it is much more subtle: it affects the subsurface layers of the material. Furthermore, the physical properties induced by chatter, for example, are different from those which produce roughness. The temperatures and stresses introduced by general machining are different from those generated by chatter. The geometrical size of the deviation is obviously not proportional to its effect underneath the surface but it is at least some measure of it. On top of this is the effect of the feature of geometry on function in its own right. It will be clear from the chapter 7 on function how it is possible that a long-wavelength component on the surface can affect performance differently from that of a shorter wavelength of the same amplitude. There are, of course, many examples where the total geometry is important in the function of the
workpiece and under these circumstances it is nonsense to separate out all the geometrical constituents. The same is true from the manufacturing signature point of view. The breakdown of the geometry into these three components represents probably the first attempt at surface characterization. From what has been said it might be thought that the concept of “sampling length” is confined to roughness measurement in the presence of waviness. Historically this is so. Recent thoughts have suggested that in order to rationalize the measurement procedure the same “sampling length” procedure can be adapted to measure “waviness” in the presence of form error, and so on to include the whole of the primary profile. Hence lr, the sampling length for roughness, is joined by lw. For simplicity roughness is usually the surface feature considered in the text. It is most convenient to describe the
7
Characterization
nature and assessment of surface roughness with the assumption that no other type of deviation is present. Then waviness will be brought into the picture and finally errors for form. From a formal point of view it would be advantageous to include them all at the same time but this implies that they are all able to be measured at the same time, which is only possible in some isolated cases.
A
(a)
500×
B
Air
C
D
Material 500× A B CD
2.2 SURFACE GEOMETRY ASSESSMENT AND PARAMETERS 2.2.1 General—Roughness Review Surface roughness is that part of the irregularities on a surface left after manufacture which are held to be inherent in the material removal process itself as opposed to waviness which may be due to the poor performance of an individual machine. (BS 1134 1973) mentions this in passing. In general, the roughness includes the tool traverse feed marks such as are found in turning and grinding and the irregularities within them produced by microfracture, built-up edge on the tool, etc. The word “lay” is used to describe the direction of the predominant surface pattern. In practice it is considered to be most economical in effort to measure across the lay rather than along it, although there are exceptions to this rule, particularly in frictional problems or sealing (see Chapter 7). Surface roughness is generally examined in plan i.e., areal view with the aid of optical and electron microscopes, in crosssections normal to the surface with stylus instruments and, in oblique cross-sections, by optical interference methods. These will be discussed separately in Sections 4.2.7, 4.3, and 4.4.5. First it is useful to discuss the scales of size involved and to dispel some common misconceptions. Surface roughness covers a wide dimensional range, extending from that produced in the largest planing machines having a traverse step of 20 mm or so, down to the finest lapping where the scratch marks may be spaced by a few tenths of a micrometer. These scales of size refer to conventional processes. They have to be extended even lower with non-conventional and energy beam machining where the machining element can be as small as an ion or electron, in which case the scale goes down to the atomic in height and spacing. The peak-to-valley height of surface roughness is usually found to be small compared with the spacing of the crests; it runs from about 50 µm down to less than a few thousandths of a micrometer for molecular removal processes. The relative proportions of height and length lead to the use of compressed profile graphs, the nature of which must be understood from the outset. As an example, Figure 2.2 shows a very short length of the profile of a cross-section of a ground surface, magnified 5000 ×. The representation of the surface by means of a profile graph will be used extensively in this book because it is a very convenient way to portray many of the geometrical features of the surface. Also it is practical in size and reflects the conventional way of representing surfaces in the past. That it does not show the “areal” characteristics of the surface is
(b)
5000× 100×
FIGURE 2.2 Visual distortion caused by making usable chart length.
understood. The mapping methods described later will go into this other aspect of surface characterization. However, it is vital to understand what is in effect a shorthand way of showing up the surface features. Even this method has proved to be misleading in some ways, as will be seen. The length of the section in Figure 2.2 from A to D embraces only 0.1 mm of the surface, and this is not enough to be representative. To cover a sufficient length of surface profile without unduly increasing the length of the chart, it is customary to use a much lower horizontal than vertical magnification. The result may then look like Figure 2.2b. All the information contained in the length AD is now compressed into the portion A′D′ with the advantage that much more information can be contained in the length of the chart, but with the attendant disadvantage that the slopes of the flanks are enormously exaggerated, in the ratio of the vertical to horizontal magnifications. Thus it is essential, when looking at a profile graph, to note both magnifications and to remember that what may appear to be fragile peaks and narrow valleys may represent quite gentle undulations on the actual surface. Compression ratios up to 100:1 are often used. Many models of surfaces used in tribology have been misused simply because of this elementary misunderstanding of the true dimensions of the surface. Examination of an uncompressed cross-section immediately highlights the error in the philosophy of “knocking off of the peaks during wear!” The photomicrographs and cross-sections of some typical surfaces can be examined in Figure 2.3. The photomicrographs (plan or so-called areal views) give an excellent idea of the lay and often of the distance (or spacing) between successive crests, but they give no idea of the dimensions of the irregularities measured normal to the surface. The profile graph shown beneath each of the photomicrographs is an end view of approximately the same part of the surface, equally magnified horizontally, but more highly magnified vertically. The amount of distortion is indicated by the ratio of the two values given for the magnification, for example 15,000 × 150, of which the first is the vertical and the second the horizontal
8
Handbook of Surface and Nanometrology, Second Edition
Shaped ×3
800 µ˝
400/3 Ground × 150
20 µ˝
Diamond turned × 150 15 µ˝
Lapped × 150
2 µ˝
FIGURE 2.3 Photo micrographs showing plan view, and graphs showing cross-section (with exaggerated scale of height) of typical machined surfaces—The classic Reason picture.
magnification. This figure is a classic, having being compiled by Reason [2] in the 1940s and still instructive today! In principle, at least two cross-sections at right angles are needed to establish the topography of the surface, and it has been shown that five sections in arbitrary directions should be used in practice; when the irregularities to be portrayed are seen to have a marked sense of direction and are sufficiently uniform, a single cross-section approximately at right angles to their length will often suffice. Each cross-section must be long enough to provide a representative sample of the roughness to be measured; the degree of uniformity, if in doubt, should be checked by taking a sufficient number of cross-sections distributed over the surface. When the directions of the constituent patterns are inclined to each other, the presence of each is generally obvious from the appearance of the surface, but when a profile graph alone is available, it may be necessary to know something of the process used before
being able to decide whether or not the profile shows waviness. This dilemma will be examined in the next section. Examination of the typical waveforms in Figure 2.3 shows that there is a very wide range of amplitudes and crest spacings found in machining processes, up to about five orders of magnitude in height and three in spacing. Furthermore, the geometric nature of the surfaces is different. This means, for example, that in the cross-sections shown many different shapes of profile are encountered, some engrailed in nature and some invected and yet others more or less random. Basically the nature of the signals that have to be dealt with in surface roughness is more complex than those obtained from practically any sort of physical phenomena. This is not only due to the complex nature of some of the processes and their effect on the surface skin, but also due to the fact that the final geometrical nature of the surface is often a culmination of more than one process, and that the characteristics of any
9
Characterization
process are not necessarily eradicated completely by the following one. This is certainly true from the point of view of the thermal history of the surface skin, as will be discussed later. It is because of these and other complexities that many of the methods of surface measurement are to some extent complementary. Some methods of assessment are more suitable to describe surface behavior than others. Ideally, to get a complete picture of the surface, many techniques need to be used; no single method can be expected to give the whole story. This will be seen in Chapter 4 on instrumentation. The problem instrumentally is therefore the extent of the compromise between the specific fidelity of the technique on the one hand and its usefulness in as many applications as possible on the other. The same is true of surface characterization: for many purposes it is not necessary to specify the whole surface but just a part of it. In what follows the general problem will be stated. This will be followed by a breakdown of the constituent assessment issues. However, it must never be forgotten that the surface is three dimensional and, in most functional applications, it is the properties of the three-dimensional gap between two surfaces which are of importance. Any rigorous method of assessing surface geometry should be capable of being extended to cover this complex situation. An attempt has been made in Chapter 7. The three-dimensional surface z = f(x, y) has properties of height and length in two dimensions. To avoid confusion between what is a three-dimensional or a two-dimensional surface, the term “areal” is used to indicate the whole surface. This is because the terms 2D and 3D have both been used in the literature to mean the complete surface. Some explanation is needed here, of the use of the term “areal.” This is used because the area being examined is an independent factor: it is up to the investigator what the area to be looked at actually is: the values of the dimensions are by choice, on the other hand, the values of the feature to be investigated over the area are not known prior to the measurement. The term “areal” therefore should be applied to all measurement situations where this relationship holds irrespective of the feature to be measured, whether it is height or conductivity or whatever! The term 3D should be used when all three axes are independently allocated as in a conventional coordinate measuring machine. There are a number of ways of tackling the problem of characterization; which is used is dependent on the type of surface, whether or not form error is present and so on. The overall picture of characterization will be built up historically as it occurred. As usual, assessment was dominated by the available means of measuring the surface in the first place. So because the stylus method of measurement has proved to be the most useful owing to its convenient output, ease of use and robustness, and because the stylus instrument usually measures one sample of the whole surface, the evaluation of a single cross-section (or profile) will be considered first. In many cases this single-profile evaluation is sufficient to give an adequate idea of the surface; in some cases it is
not. Whether or not the profile is a sufficient representation is irrelevant; it is the cornerstone upon which surface metrology has been built. In subsequent sections of this chapter the examination of the surface will be extended to cover the whole geometry. In the next section it will be assumed that the cross-section does not suffer from any distortions which may be introduced by the instrument, such as the finite stylus tip or limited resolution of the optical device. Such problems will be examined in detail in Chapter 4, Sections 4.2.2 and 4.4.1.1. Problems of the length of profile and the reliability of the parameters will be deferred until Chapter 5. 2.2.1.1 Profile Parameters (ISO 25178 Part 2 and 4278) The profile graph shown in Figure 2.4 and represented by z = f(x) could have been obtained by a number of different methods but it is basically a waveform which could appear on any chart expressing voltage, temperature, flow, or whatever. It could therefore be argued that it should be representable in the same sort of way as for these physical quantities. To some extent this is true but there is a limit to how far the analogy can be taken. The simplest way of looking at this is to regard the waveform as being made up of amplitude (height) features and wavelength (spacing) features, both independent of each other. The next step is to specify a minimum set of numbers to characterize both types of dimension adequately. There is a definite need to constrain the number of parameters to be specified even if it means dropping a certain amount of information, because in practice these numbers will have to be communicated from the designer to the production engineer using the technical drawing or its equivalent. More than two numbers often cause problems of comprehension. Too many numbers in a specification can result in all being left off, which leaves a worse situation than if only one had been used. Of the height information and the spacing information it has been conventional to regard the height information as the more important simply because it seems to relate more readily to functional importance. For this reason most early surface finish parameters relate only to the height information in the profile and not to the spacing. The historical evolution of the parameters will be described in the introduction to Chapter 4. The definitive books prior to 1970 are contained in References [1–7]. However, there has been a general tendency to approach the problem of amplitude characterization in two ways, one attempting in a crude way to characterize functions by measuring peaks, and the other to control the process by measuring average values. The argument for using peaks seems sensible
z x
FIGURE 2.4 Typical profile graph.
10
and useful because it is quite easy to relate peak-to-valley measurements of a profile to variations in the straightness of interferometer fringes, so there was, in essence, the possibility of a traceable link between contact methods and optical ones. This is the approach used by the USSR and Germany in the 1940s and until recently. The UK and USA, on the other hand, realized at the outset that the measurement of peak parameters is more difficult than measuring averages, and concentrated therefore on the latter which, because of their statistical stability, became more suitable for quality control of the manufacturing process. Peak measurements are essentially divergent rather than convergent in stability; the bigger the length of profile or length of assessment the larger the value becomes. This is not true for averages; the sampled average tends to converge on the true value the larger the number of values taken. The formal approach to statistical reliability will be left to Chapter 5. However, in order to bring out the nature of the characterization used in the past it is necessary to point out some of the standard terms governing the actual length of profile used. The basic unit is the sampling length. It is not called the “sample length” because this is a general term whereas sampling length has a specific meaning which is “the length of assessment over which the surface roughness can be considered to be representative.” Obviously the application of such a definition is fraught with difficulty because it depends on the parameter and the degree of confidence required. For the purpose of this subsection the length will be assumed to be adequate—whatever that means. The value of the sampling length is a compromise. On the one hand, it should be long enough to get a statistically good representation of the surface roughness. On the other, if it is made too big, longer components of the geometry, such as waviness, will be drawn in if present and included as roughness. The concept of sampling length therefore has two jobs, not one. For this reason its use has often been misunderstood. It has consequently been drawn inextricably into many arguments on reference lines, filtering, and reliability. It is brought in here to reflect its use in defining parameters. Sometimes the instrument takes more than one sampling length in its assessment and sometimes some of the total length traversed by the instrument is not assessed for mechanical or filtering reasons, as will be described in Chapter 4. However, the usual sampling length of value 0.03 in (0.8 mm) was chosen empirically in the early 1940s in the UK by Rank Taylor Hobson from the examination of hundreds of typical surfaces [2]. Also, an evaluation length of nominally five sampling lengths was chosen by the same empirical method. In those days the term “sampling length” did not exist; it was referred to as the meter cut-off length. The reason for this was that it also referred to the cut-off of the filter used to smooth the meter reading. Some typical sampling lengths for different types of surface are given in Tables 2.1 through 2.4. In Tables 2.2 through 2.4 some notation will be used which is explained fully later. See Glossary for details. The usual spatial situation is shown in Figure 2.5.
Handbook of Surface and Nanometrology, Second Edition
TABLE 2.1 Sampling Lengths for Ra, Rz, and Ry of Periodic Profiles Sm (mm) Over (0.013) 0.04 0.13 0.4 1.3
Up to (Inclusive)
Sampling Length (mm)
Evaluation Length (mm)
0.04 0.13 0.4 1.3 4.0
0.08 0.25 0.8 2.5 8.0
0.4 1.25 4.0 12.5 40.0
TABLE 2.2 Roughness Sampling Lengths for the Measurement of Ra, Rq, Rsk, Rku, RΔq and Curves and Related Parameters for Non-Periodic Profiles (For Example Ground Profiles) Ra (µm)
Roughness Sampling Length lr (mm)
(0.006), Ra < 0.02 0.02, Ra < 0.1 0.1, Ra < 2 2, Ra < 10 10, Ra < 80
Roughness Evaluation Length ln (mm)
0.08
0.4
0.25 0.8 2.5 8
1.25 4 12.5 40
TABLE 2.3 Roughness Sampling Lengths for the Measurement of Rz, Rv , Rp, Rc, and Rt of Non-Periodic Profiles (For Example Ground Profiles) Rz 1 Rz1 Max.2 (µm) (0.025), Rz, Rz1 max. < 0.1 0.1, Rz, Rz1 max. < 0.5 0.5, Rz, Rz1 max. < 10 10, Rz, Rz1 max. < 50 50, Rz, Rz1 max. < 200 1 2
Roughness Sampling Length lr (mm)
Roughness Evaluation Length ln (mm)
0.08 0.25 0.8 2.5 8
0.4 1.25 4 12.5 40
Rz is used when measuring Rz, Rv, Rp, Rc, and Rt. Rz1 max. is used only when measuring Rz1 max., Rv1 max., Rp1 max., Rc1 max., and Rt1 max.
Most amplitude parameters are referred to one sampling length in the standards although, in practice, more than one is used. Some specific typical parameters will now be given in more detail. Attempts to quantify the roughness height have historically been broken into two camps: one measuring peak-tovalley heights, the other average heights. Peak measurement was advocated by the Germans, French, and other Europeans
11
Characterization
TABLE 2.4 Roughness Sampling Lengths for the Measurement of R-Parameters of Periodic Profiles, and RSm of Periodic and Non-Periodic Profiles RSm (µm) 0.013, RSm < 0.04 0.04, RSm < 0.13 0.13, RSm < 0.4 0.4, RSm < 1.3 1.3, RSm < 4
Roughness Sampling Length lr (mm)
Roughness Evaluation Length ln (mm)
0.08 0.25 0.8 2.5 8
0.4 1.25 4 12.5 40
Rt
FIGURE 2.6 Amplitude parameters—peaks Rt.
P5
V2
P1
P3 P4
V5
V4
P2
V3
V1
Evaluation length
FIGURE 2.7 Peak parameters R z. R
Sampling length Evaluation length
Evaluation length Traverse length
FIGURE 2.5 Length measures on a profile.
in an effort to link surface measurements obtained from stylus instruments to fringe deviations obtained using interferometers [3,5]. Although a very laudable concept, it ran into difficulties because of the difficulty of measuring or even finding the highest peak-to-valley height on the surface. The British and Americans adopted an average height measurement philosophy in order to get a workable parameter. It should also be realized that from the outset, many firms developed their very own surface parameters which sometimes bore little resemblance to those suggested as preferred parameters by the ISO and national institutions. These individual parameters were devised to satisfy an in-house need and as such were acceptable. The problem arose when subcontractors were expected to buy equipment to measure the same parameters. This situation was an instrument-maker’s nightmare until the more versatile computer systems emerged. In fact, it was one of the reasons for developing computer systems along with the need to measure more complicated parameters for investigating functional behavior. 2.2.1.1.1 Amplitude Parameters Note—None of the definitions given below are sacrosanct— they keep changing, especially the symbols used, which makes it very difficult to provide a useful up to date information so reference to the ISO standards at all times is advisable, in particular ISO 25178. In what follows there is a brief outline. ISO standards are mentioned later on where applicable. Figure 2.6 shows a typical profile trace condensed in the horizontal direction for convenience of display [4]. Perhaps the most obvious way of putting a numerical value to its magnitude is to measure the heights of the peaks and valleys. The level from which to measure is taken here to be the bottom of
5% 95%
Rautiefe
FIGURE 2.8 Peak parameter—Rautiefe.
the chart. However, this assumes that the profile is reasonably level relative to the bottom of the chart. One such parameter is shown as Rt in Figure 2.6. This parameter is simply the difference in level between the highest peak and the lowest valley in the length of profile called the sampling length. A similar parameter called Rz is shown in Figure 2.7. The formula for Rz is Rz = =
( P1 + P2 + P3 + P4 + P5 ) − (V1 + V2 + V3 + V4 + V5 ) 5
∑
5 i =1
Pi − 5
∑
5 i =1
Vi
(2.1)
Rz is, in effect, the average of the height difference between the five highest peaks and the five lowest valleys. The reason for taking an average value of peaks is to minimize the effect of unrepresentative peaks or valleys which occasionally occur and can give an erroneous value if taken singly. Rz is used often without reference to a mean line. It has also been used to get some idea of the surface roughness on very short lengths of surface such as might be found on a lip or shoulder where not even one sampling length of surface is available. Rz is an insurance against freaks. There is another way of insuring against the freak occurrence. This is given the name Rautiefe. Its derivation is shown in Figure 2.8. It is the separation of two parallel lines cutting through the profile such that the upper one is in metal for 5% of its path and the lower one is in metal for 95% (or 90%) of its path. This parameter not only attempts to relate the profile to some semblance of mechanical function, but also contains the germ of the more advanced statistical methods described in Section 2.2.2. It suffers from the drawback that it cannot be measured from the chart of the profile as easily as Rt or Rz.
12
Handbook of Surface and Nanometrology, Second Edition
Ra line
Valleys inverted
Rq
Ra Levelling depth
Rt2
Rt3
Rt4
Rt5
Sampling length Evaluation length
FIGURE 2.10â•… Ten-point height Rz.
A slightly different peak measure is Rp, the leveling depth (Figure 2.9). This is the average depth of the profile below a reference line drawn through the highest peaks taken through the profile. On a profile the reference line would have to touch the two highest peaks. Other definitions of Rp exist. These depend on the precise form of definition of the reference line. Another definition of Rp can be given simply as the maximum peak height from a mean line positioned in the middle of the profile such that the area above the line is equal to that below the line. A corresponding maximum valley parameter Rv can also be defined from this line. Sometimes the peak-to-valley measurement has been limited to a single sample length, such as Rp, but another assessment has been used, called Rtm, in which some averaging of peaks is achieved by taking the Rt values from a succession of adjacent (contiguous) sampling lengths and averaging them. Typically, five sampling lengths are used for the reasons given earlier (Figure 2.10). Thus
Rtm
∑ =
5 i =1
5
R1
.
Sampling length
FIGURE 2.11â•… Average parameters—Ra and Rq.
FIGURE 2.9â•… Peak parameter-leveling depth Rp. Rt1
Mean line
RA
(2.2)
This method, although different from Rz, illustrates the quandary faced by metrologists determined to use peak-to-valley or extrema criteria for the evaluation of surface features. Some degree of averaging has to be incorporated in order to make the method workable and capable of being calibrated. Many other methods have been tried, such as R3z, the difference in height between the third highest peak and the third lowest valley within a sampling length. This has been used quite extensively in Japan. Basically, at this level of technology, from a functional point of view, it does not really matter which peak or average peak parameter is used as long as it is consistently used and the definition agreed between the various people using the technique. Many problems arise because definitions that are assumed to be fixed are found to be different at a later date, due, perhaps, to a change in a standard.
Other attempts to bridge the gap between peak, average peak and average values will be discussed after a brief description of the average parameter. The most obvious method of increasing the reliability of the amplitude measure involves using all of the profile signal rather than just the maximum and minimum values. The best known and most often used today is Ra , defined relative to a mean reference line. It is the mean departure of the profile from the reference line. This is shown in Figure 2.11. Thus, if z = f(x) is the profile measured from the reference mean line and L is the length of the profile being assessed (this can be the sampling length), then Ra is defined by
Ra =
1 L
∫
L
| z | dx.
(2.3)
0
Another parameter shown in Figure 2.11 is Rq, the RMS deviation defined again relative to a mean line as
Rq =
1 L
∫
L
z 2 dx
(2.4)
0
Although Rq is more statistical in nature it is difficult to measure from a chart. Early measurement in the USA was in fact an RMS value. The arithmetic average (AA) on drawings invariably implied measurement of an RMS value and dividing by a fixed constant of 1.11. This gave the true AA value for a sine wave but no other waveform. Other names have been given to the Ra value, namely the center line average (CLA) value in the UK. Because of its wide acceptance and its usefulness it seems likely that the Ra value will continue to hold its place as the foremost amplitude measurement. However, this does not imply that other mean value parameters are not forthcoming. One measure is called the R value, which is derived by drawing two lines through the peaks and valleys respectively. This method is also called the “motif” method and is interesting in that there are certain allowances in the rules for constructing both the superior envelope through the peaks and the inferior envelope through the€ valleys to Â�preclude certain values, as shown in Figure 2.12. See later. R is taken to be the mean of several values of the separation of the envelopes. Mention of these envelopes will also be made in the next section on waviness. Also, the use of envelopes to provide boundaries from which height measurements can be made will be discussed in Chapter 5. Parameters such as R have only been in vogue since the advent of digital methods for the simple reason that exclusion conditions for some of the peaks and valleys are difficult to implement accurately with analog devices. The final conventional parameter to be discussed in this section is, by its nature, statistical. However, because it was
13
Characterization
Superior envelope
TABLE 2.5 Parameter Attributes
Inferior envelope
Parameter
FIGURE 2.12â•… Motif method—R and W.
(a)
mR (z)%
0 z
100% (b) Rpk
Height
40%
Rsk
Rvk 0%
M
100
FIGURE 2.13â•… (a) Material ratio curve; (b) Rpk, Rvk, Rk.
introduced rather early in the natural evolution of the subject [8], it will be included in this section. This curve is fundamental to surface metrology and will keep arising in the text. This curve is the material ratio curve. In Figure 2.8, the Rautiefe [3] is shown defined relative to the air/metal ratio. A plot of the ratio of air to metal starting at the highest peak and dropping down to the lowest valley on the profile is referred to as the bearing ratio, material ratio, Abbott–Firestone curve, and even for a time tragenteil (Figure 2.13). In this book the term material ratio will be used as the preferred term. The material ratio at height z MR(z) is given by Σtp(z)/L = MR(z), where Σtp(z) is the sum of the material t found at level z over a length L an important point is that the material ratio obtained from the profile is the same as that obtained over an area for isotropic surfaces. The height distribution function and the amplitude probability density function (APDF) can be derived from this curve. Such transpositions and measurements taken from them have been proposed by Pesante [9] and Ehrenreich [10]. A great deal of additional interest in this parameter has been generated with the emergence of multiprocesses (or stratified processes). See ISO 13565-2. Note that at any one level the value of the material ratio curve (bearing ratio) is a ratio and not a length. It would give the same shaped curve if the horizontal scale of the profile were shrunk or expanded. Indeed it would give the same curve if the order of the tp values were exchanged or even pushed up against each other; the actual horizontal scale or order of the peaks horizontally is not relevant. A more detailed discussion of this method of assessing the material ratio curve is given in Chapter 5. It can be seen from this introduction that there is an additional criterion to be used for parameters. This concerns the
Ease of Measurement
Reliability
Very difficult Difficult Moderate Easy Very easy
Very high High Moderate Low Very low
Rq Ra Rtm Rt Rmax
Normal Ra values in µm
Roughness grade number
50
Ν12
25
Ν11
12.5
Ν10
6.3
Ν9
3.2
Ν8
1.6
Ν7
0.8
Ν6
0.4
Ν5
0.2
Ν4
0.1
Ν3
0.05
Ν2
0.025
Ν1
Increasing roughness
FIGURE 2.14â•… Roughness grades.
ease of graphical measurement. It seems that any parameter which can be easily measured is not very reliable and vice versa. This is shown in Table 2.5. Most of the parameters considered so far are very much a result of historical development and not very significant in themselves. For example, from the point of view of statistical importance, Rq is much more valid than Ra but in the early days it could not readily be measured. Today this is not true, but still the old parameter exists. The real exception to this rule is the material (bearing ratio) curve which existed almost at the start of roughness characterization and in fact contained many of the best features of any parameter; it is functional and reliable. It also has a reasonable theoretical basis. The parameters described in this book are nothing like exhaustive, neither should they be. In a healthy subject the parameters need to change to reflect circumstances. As if this is not confusing enough some countries try to classify the parameters in terms of size. One typical classification is shown in Figure 2.14. This is called the N system. Another
14
Handbook of Surface and Nanometrology, Second Edition
TABLE 2.6 N Values CLASS 1
2 3 4 5 6 7 8 9 10 11 12 13 14 Unit Standard
UK
USA
GERMANY
USSR
JAPAN
ISO
1
400/630
200
200/280
200 (R)
2 4 8 16 32 63 125 250 500 1000 – – –
0.25 0.5 1.0 2 4 8 16 32 63 125 250 500 1000 – – –
160/250 63/100 25/40 16 6.3 4.0 2.5 1.6 1 0.63 0.4/0.25 0.16/0.1 0.06/0.04
125 63 40 6.3 3.2 1.6 0.8 0.4 0.2 0.1 0.05 0.12 0.06
100/140 50/70 25/35 18 12 6 3 1.5 0.8 0.4 0.2 0.1 –
125 63 40 6.3 3.2 (Ra) 1.6 0.8 0.4 0.2 0.1 0.05 0.025 0.012
BS1134 1950
B46 1955
4763 DIN 1954
GOST2780 1951
JIS 1955
1953
TABLE 2.7 Abbreviations for Processes Turning Diamond Turning Grinding Honing Lapping Polishing
T DT G H L Po
Boring
B
Reaming Miling Planing Scraping Broaching
R M P S Br
Note: Obviously this shorthand is different in different languages.
system uses a set of del symbols ∇∇∇ etc. The problem here is that standard documents can become cluttered up with what are in effect “in-house” characterization methods used by large companies. Table 2.6 shows the hopeless confusion for some countries. High N means rough for some countries yet for others it means smooth. Unfortunately the N numbers are still used! Great care has to be taken to make sure which N scale is being used! Also remember that the letter N is used for the number of sampling lengths in the assessment length which although usually 5 is not necessarily so especially when there is only a short length of surface available for assessment such as on a lip or flange. In some documents the finish is referred to by process. Table 2.7 gives a few typical examples. 2.2.1.1.2 Spacing Parameters The height parameters, such as Ra and Rt have usually been specified on the drawing in an attempt to control the
manufacturing process. To a large extent this in turn has been successful in controlling the performance of the part. Nowadays, however, with increasing efforts to optimize the function, the functional performance of a workpiece as a requirement has been growing. One way of supplementing the height information is to provide some index of crest spacings on the surface. As in the case of the height parameters many propositions have been made. One of the simplest, called the high-spot count, is a measure of the number of crossings of the profile through the mean line z = 0. Various alternatives to the mean line crossings have been suggested. For instance, an index can be taken to be the number of crossings of the profile by a line parallel to the mean line but displaced vertically by one Ra value. Much use has been made of this concept in the statistical methods described in the Section 2.1.3 on statistical parameters. Whereas the high-spot count is referred to at a given height from the reference line within the profile, the peak count is not. It is just a measure of maxima irrespective of height. This count is very easy to measure from the record of the profile and hence it has had widespread use, especially in the sheet steel industry. The big disadvantage of this method is that it is very dependent on the frequency response of the instrument, a point which will be expanded upon later. The effect of this is to make comparisons between peak counts very difficult. One technique which has been used in the past to minimize this effect is to have some form of amplitude discrimination. For instance, a peak is not registered unless the previous valley lies 50-micro inches below it. This approach has also been
15
Characterization
used in the steel industry in the USA (Figure 2.15). Various other methods of discrimination have been tried but they do and should relate to the particular function. The peak density, the zero-crossing density and the peak count, in which an amplitude discriminating band is used, are shown in Figures 2.15 through 2.18. Later on it will be demonstrated that the apparently simplistic methods of assessing surfaces shown here should not be treated with contempt. Many current theories make use of a number of these concepts; for example, the ratio of the high-spot count to the peak count can be used as a measure of the process. This concept is used extensively in mathematical modeling to which some importance will be attached. Other names for peak spacing parameters have been advocated in international and national standards and, in particular, VNIIMS Moscow [11]. One is the S value which is the average distance between local (small) peaks (Figure 2.16) and Sm the average distance between positive crossings of the profile with the mean line (Figure 2.17). The ratio of S/Sm has been used in the former USSR for characterizing surfaces. For a very random surface this ratio is low, yet for a deterministic one it can approach unity. Both S and Sm are meant to be related to one sampling length. Other peak counts incorporate an amplitude discriminating factor (Figure 2.18). The value of this factor depends on the application.
Amplitude discrimination
FIGURE 2.15â•… Other peak parameters—amplitude discrimination spacing parameters.
There is yet another wavelength parameter [12] which is almost the average distance between peaks—but not quite! This is the average wavelength of the surface. It takes into account the size of the peaks and the basic sinusoidal wavelengths making up the waveform. It will only be mentioned here but will be considered in more detail in Section 2.1.3.4. However, it is useful to introduce it because it indicates that some parameters are best expressed as a mixture of the height and wavelength dimensions; these are called hybrid parameters and some will be described here. 2.2.1.1.3â•… Hybrid Parameters Other suggested parameters have incorporated both height and spacing information. These parameters have usually been derived from the differentials of the waveform. A number of investigators have found this type of parameter useful, particularly in friction wear and optical behavior. Spacing and hybrid parameters were initially introduced because of the inability to specify the texture effectively by means only of height parameters. Their widespread use, however, was severely curtailed because of the inability to measure them properly. There were many attempts to use the hybrid parameters to characterize surfaces, notably by Myers [14]. The difficulty arose in measuring differentials by analog means. By their very nature differentials are noisy. This meant that many early attempts were unreliable and so, instead of clarifying the characterization, they often clouded it. This situation has largely been overcome by the use of digital methods but it should be emphasized that great care still has to be taken. Some examples are the average (Δα) or RMS (Δq) slope, the curvature (ρ), peak curvature, etc. Thus the average slope (Δa)is given by ∆a =
l2
l1
l4
l3
l5
l6
FIGURE 2.16â•… Length parameters—peak density S.
l2
l3
l4
l5 l6
l7
l8
l9
FIGURE 2.17â•… Length parameters—zero crossings SM.
Count 1
Count 2
1 ∆q = L
FIGURE 2.18â•… Length parameter—peak count (amplitude discriÂ� minator).
0
dz dx dx
(2.5)
∫
L
0
1/ 2
2 dz dx . dx
(2.6)
Note that Δa and Δq are the same to slope measurement as Ra and Rq are to amplitude and λa and λq to spacing. The average curvature of the profile ρ is given in Equation 2.7. Signs are ignored.
Count 3
Discriminator band
∫
L
where dz/dx is the instantaneous slope of the profile. These parameters are fundamental in function and should be remembered here for reference in Chapter 7 on function. The RMS slope (Δq) is defined as
Mean line
l1
1 L
ρ=
1 L
∫
L
0
d 2 z /dx 2
[1 + (dz /dx )2 ]
3/ 2
dx
(2.7)
This formula can be simplified if account is taken of the fact that dz/dx is usually small on a surface. (This is a result which is true in certain cases only, particularly rough surfaces.)
16
Handbook of Surface and Nanometrology, Second Edition
Thus,
filtering concepts discussed in this section should be linked with Section 2.3 on waviness for completeness. It should not be thought that the establishment of reference lines and the definition of so-called sampling lengths are purely instrumental considerations. They are not. These issues constitute a very important aspect of characterization of the surface into its most significant components. Often they provide the means whereby specific features can be highlighted in space. This is why they are included here; the reference helps to characterize the roughness. However, there are many occasions when the reference itself needs to be classified. This is when the reference line is considered to contain the waviness. In these cases the reference line has to be classified in much the same way as the roughness has been considered. Waviness characterization is considered in Section 2.3. Both roughness and waviness characterization appear in Chapter 3 on processing and Chapter 4 on instrumentation. Reference lines therefore seem to occur all over the place! This is inevitable because the numerical values of many of the parameters depend on which one, if any, is used. The problem is this: surface roughness is a deviation—it needs a reference from which to quantify it. Ideally the external mechanical reference provided within the instrument should be positioned within the roughness marks. This is obviously impossible. All it can do is to enable, by means of the pick-up and transducer, the generation of the surface data, that is the profile. It is then necessary to use some mathematical procedure to position the reference within the profile from where the roughness can be measured. Because the problems associated with reference lines occurred historically before even areal considerations or random processes became important, they have to be considered here. Their involvement is deeply entwined with the development of the subject as a whole and is just as important today as it was when surface metrology was in its infancy.
1 L
ρ
∫
L
0
d 2z dx. dx 2
(2.8)
Curvature is the reciprocal of the radius of the profile at any point. Other variations of this definition have been proposed. For instance, the average peak curvature (ρΔ), the average Â�valley curvature (ρ↜∇), etc. As for peaks and valleys these definitions have to be qualified somewhat to minimize the errors due to variations in resolution, frequency response, etc. These curvature formulae are considered to be especially important in contact theory. Another parameter sometimes used is the profile length lp (Figure 2.19). This is given by 1 lp = L
∫
L
0
2
1/ 2
dz + 1 dx dx
(2.9)
which for small dz/dx reduces to lp
1 L
∫
1+
L
0
1 dz 2 1 + dx 2 dx
mean square slope . 2
(2.10)
The directionality D of the profile can also be defined using the differential parameters. Thus D=
L1 – L2 L
(2.11)
where L1 is the length of profile along the horizontal scale having positive slope and L2 is the length having a negative slope. Interest has been shown in this directionality parameter in the context of journal bearings. Considerable differences in wear properties have been encountered depending upon how the directionality of the roundness profile of the shaft compares with the direction of rotation of the bearing. In this case the directionality of the circumferential surface roughness is the important factor. The next section is concerned with methods of separating waviness from roughness. Part of the section is devoted to the theory of linear filtering, which can be omitted on a first reading. However, it is necessary to introduce the concepts here because so much of what follows is dependent upon them. Filtering is a form of spatial characterization. The S1S
2
S3
Profile length Σs Evaluation length
FIGURE 2.19â•… Profile length.
2.2.1.2â•…Reference Lines Many of the parameters described above depend on the definition of some reference line from which to measure. This reference line has to have a fixed known height relative to the roughness, it has to have a predetermined shape and its length must be known. This aspect of surface metrology has been and still is a fundamental problem in the assessment of surface roughness. Historically the first reference from which to measure was the bottom of the chart upon which the graph (profile) of the surface was drawn. This was acceptable for measuring the peak to valley and this was the first parameter for this reason. But because of its variability it was superseded by parameters which measured average values and root mean square values which will be discussed shortly. However these parameters require a line from which to measure positioned within the profile according to various rules. The preferred line was obviously a mean line about which the roughness had an equal value, above and below so for years the search was on to find ways of generating such a line on the graph and in the meter. The mechanism for getting the line and the parameters measured from it went under the collective name
17
Characterization
of the “M System.” The filtering methods described later all fell under this heading Other systems such as the “E” System followed. As for the determination of the sampling length, this is a basic device for limiting the length of surface over which an individual measurement of roughness is made, as shown in Figure 2.5. If the roughness marks, that is the process marks, are repetitive, then the sampling length should include about 10 whole marks within it. This criterion was originally Â�established empirically but it has stood the test of time and is still used. The early investigations led to the standard sampling length of 0.8 mm (0.03 in) being adopted as standard, this being about 10 times larger than the typical feed rate of turning in the 1940s [2]. For random marks such as found in grinding, the determination of the sampling length is more difficult because of the lack of obvious cycles of repetition. However, a rule of thumb can be given here and verified later, which is that if a line is drawn by eye through the profile to include the roughness marks only then the sample length should include between 20 and 30 crossings of the profile with the line. Small deviations of the reference line from being straight or misplaced vertically are not important. This corresponds to having a high-spot count of about 10. Formally, the determination depends upon a knowledge of the statistics of the surface, which will be considered in the next section. The term sampling length used to be called the “cut-off length” or sometimes the “meter cut-off.” In the past, by convention, there was a selection of sampling lengths available for use to suit whichever process was being measured. For convenience and to provide a basis for instrumentation a series (originally) based on √10 differences has been standardized in the British Standard BS 1134, the U.S. Standard B46 and ISO Recommendation R468. The accepted values with the Imperial equivalent are as follows: 0.08 0.003
0.25 0.01
0.8 0.03
2.5 0.1
8.0 mm 0.3 in
Note: (0.03 in = 0.762 mm rounded to 0.8 mm)
It should be said here that the specific values were chosen for convenience and are by no means sacrosanct. For many of the new machining processes it could be argued that any suitable sampling length could be chosen. When the sampling length has been determined the reference has to be positioned in the profile in such a way that departures from it represent the roughness. For many parameters five sampling lengths are used (Figure 2.20). Four main types of line have been investigated in the past all over the world and each incorporates some wavelength discrimination such as the sampling length limitation. These methods have been achieved in a number of different ways ranging from graphical, electrical, mechanical, and now computing. Nowadays the graphical methods are rarely used but are held in reserve.
Mean line
Evaluation length Sampling length
FIGURE 2.20â•… Sampling length.
The methods most used are straight lines, polynomials, splines, low-pass filters, and envelopes (or motifs). 2.2.1.2.1â•… Straight Lines Perhaps the simplest form of reference line that can be put onto a chart is a straight line extending over the sampling length. It can be positioned so that it touches the two highest crests within the sampling length as for measuring Rp, the leveling depth in Figure 2.9, or derived similarly from the deepest valleys or it may be a mean line, in which case the profile area enclosed above the line is equal to that below it. Note that the mean line is often referred to as the center line, and is the origin of the CLA parameter used until recently in the UK meaning the CLA or the average from the center line (mean line): now called the Ra value. The problem is how to determine the most meaningful angle and position at which to draw the line relative to the profile; a number of lines having the equal-area criterion are possible. One traditional method is to qualify the definition of equal area with a statement that the line must follow the general direction of the surface. This rather subjective method has the effect of tending to minimize the modulus of the area enclosed between the profile and the line therefore minimizing the Ra value. Another method which is not the same is that of applying a constraint to the slope and position by specifying a “best-fit” least-squares straight line through the data. In this case the line will be unique, free from subjective positioning. From the point of view of simply fitting a best line this method is very good but it has two problems associated with it. One is that it is difficult to determine from a graph and the second is that it sometimes produces unrealistic results. Whereas the former method of fitting a straight line is difficult to quantify theoretically the latter is not. If the measured values of z as a function of x on the chart are compared with the values expected from a best-fit line z′ at the same x then the problem is to minimize the sum Su where
Su =
∫
L
0
( z – z ′ ) dx. 2
(2.12)
Strictly the deviations should be in a direction normal to the best-fit line itself, that is z cos α–z′ cos α, as shown on the graph in Figure 2.21. Thus S′u is minimized where
Su =
∫
L
0
( z – z ′ ) cos α 2dx 2
(2.13)
18
Handbook of Surface and Nanometrology, Second Edition
Minimum
Minimum relative
Relative to base
c
To line
Best-fit line
α Best line of measurement
FIGURE 2.21 Best-fit least-squares lines.
Su′ =
∫
L
0
[ z ( x ) – ( mx + c )] cos2 α dx 2
(2.14)
which, given that m = tanα, is that
∫
L
0
[ z ( x ) cos α − x sin α − c cos α ] dx 2
(2.15)
is minimum, where m is the tangent and c is the intercept of the line on the z axis, from which a is obtained as 2α = tan −1 2
0 L 1 L − xdx z ( x ) dx L 0 0 (2.16) 2 L L 1 2 x dx − xdx L 0 0 2 L L 1 2 − z ( x ) dx + z ( x ) dx L 0 0
∫
L
z ( x ) xdx
∫
∫
∫
∫
∫
∫
which is in effect
covariance of x and z tan 2α = 2 variance of x − variance of
∫
L
0
z ( x ) dx 0 0 . (2.18) 2 L L 1 2 x dx − xdx L 0 0
1 xz ( x ) dx − L
∫
∫
L
xdx
∫
∫
L
c 3 = . A πn
(2.19)
Obviously for n = 1 this angle is enormous and unrealistic; the mean line has to be parallel with the crests or valleys of the sine wave. This would have been the case if a cosine rather than a sine had been selected. So the least-squares line for a periodic wave has a slope dependent upon the starting point! This makes not sense, so in order to make Definitions 2.17 and 2.19 usable n has to be large. For n = 10, c/A < 10%, which
. (2.17) z
(Both α and c or m and c are obtained by setting ∂S′u /∂α, ∂S′u /∂c = 0 or ∂S′u /∂m, ∂S′u /∂c = 0 and solving.) This formula should be used if the horizontal and vertical magnifications are equal, as they often are in flatness measurements. In the case of roughness the vertical magnification is often 50 times bigger than the horizontal so that the direction of the deviation is distorted from the normal to the line and toward the normal to the base line. Under these circumstances Equation 2.16 should be used to give m=
Digital equivalents of Equations 2.17 and 2.18 will be given in Chapter 3, Section 3.5. The advantage of using a linear mean line as opposed to a linear crest or valley line is that poor positioning of these latter lines can easily result if freak asperities are present in the profile. Despite the undoubted advantages of the best-fit line approach it does run into difficulty when periodic waveforms are being measured, for instance a sine wave. The question arises as to what constitutes a realistic mechanical direction of the line. In the case of the center line, the difficulty arises only when the sample contains a single cycle of the waveform, for when there are two or more cycles, the crest line at once determines the inclination which leads to minimum values. In the case of the least-squares mean line, however, the inclination is determined both by the starting point and by the number of cycles included in the sample. Consider Figure 2.22 where the full curve represents a single sample of a sinusoidal profile. The best-fit least-squares line has a different slope depending upon its starting point in the cycle. The intercept of the line with the starting ordinate axis may easily be shown to be a function of the number of cycles within the sample. For n samples in the cycle the intercept c as a function of the amplitude of the wave itself A is given by
Amplitude of sine wave A Best-fit line
One sine wave cycle
c
c = 3 A πn
Base line Sampling length
FIGURE 2.22 Least-squares line: n is number of cycles in sampling length.
19
Characterization
is deemed reasonable and constitutes one reason why the 10 cycles of a periodic function are used as some basis for the determination of the sampling length in terms of machine tool feed. The use of the straight reference line fitted within each of the individual sample lengths making up the evaluation length, whether by least squares or otherwise, has the advantage of simplicity but suffers from the fact that, at the end of each sampling length, the end of one line inevitably does not contact the start of the next. This means that a discontinuity is introduced into the waviness shape, both in level and in slope at each sampling length. This can cause problems in measuring the parameters considered in Section 2.1. The errors are more severe for the peak parameters than for the average ones. It has been known for a best-fit least-squares line to be used over the whole evaluation length and not be used for each individual sampling length making up the whole assessment. When this method is used obviously only the tilt of the instrument datum relative to the workpiece can be removed. Errors of form or curvature of the part cannot be removed at the same time. If, at the same time as removing tilt it is considered advantageous to remove the form, another method has to be used. 2.2.1.2.2â•… Polynomial Fitting It may be that the form can be adequately represented over the evaluation length by a cubic or quadratic Â�equation. This would give a better reference than a straight line (Figure€2.23). Then a best-fit polynomial could be used of the form z = a1 + a2 x + a3x2 + … where a1, a2, a3 are the least-squares coefficients as m and c were for the least-squares line. Best-fit straight line
Best-fit polyomial
FIGURE 2.23â•… Best-fit limitation.
In this case they can be extracted from the equations a1 L + a2
a1
∫
L
0
∫
L
0
xdx + a3
xdu + a2
∫
L
0
∫
L
0
∫
x2 =
x 2 dx + a3
L
0
∫
L
0
z ( x )dx
x 3 dx =
a1
∫
L
0
∫
∫
xz ( x )dx
(2.20)
∫
L
0
x n –1 z ( x ) dx
where n is the order of the polynomial. The big advantage of this polynomial approach is that all the data in the evaluation length can be used. There are no end effects! In other words one of the great advantages of the use of polynomials to represent tilt, waviness, and form error through the roughness data is that all the data are utilized. The penalty for this, however, is that to get the most realistic reference line the order of the polynomial should be made to “match” the geometry of the profile itself. For example, if the surface is aspheric. As an example of mismatching, consider a workpiece which is perfectly smooth and has a form error of three-quarters of a sine wave. If a sinusoidal waveform is fitted to the form error without knowing that only threequarters of the full sine wave are present then considerable errors can result. The imposition of an arbitrary period to the workpiece based only upon its length can actually introduce harmonic distortion as is shown in Figure 2.24. It is only acceptable to make an error of judgment like this when there are considerably more than one cycle of the natural wave within the length of the profile. Under these conditions the errors are reduced to an acceptable level. There is an alternative to the least-squares or best-fit approach and this is that of minimum divergence of the
Fundamental
x
f 1/L Fundamental 2/L´
x
f 1/L´
FIGURE 2.24â•… Distortion-mismatched length.
0
x n−1du + a2 x n dx + a3 x n+1 + K =
A
L´
L
A
L
∫
Harmonics
20
Handbook of Surface and Nanometrology, Second Edition
Moved box window Mid-point locus line
Running box
FIGURE 2.25â•… Mid-point locus line.
1.0 Mean line amplitude input signal amplitude
reference curve from the test piece—given that the order (e.g., quadratic or cubic) is known. The obvious example of this sort of approach is to use the Chebychev polynomials; these, however, could generate a reference curve which, unless care is taken, will suffer from the same freak behavior as is possible with crest or valley lines. One very interesting feature of this method, however, is that some attempt can be made by using the Chebychev series to characterize fully the whole profile, that is roughness, waviness, errors of form, and set-up errors, using just one type of function. This assumes that the idea of looking at the whole evaluation length in one go, rather than breaking it down into sampling lengths, has been abandoned—which it does not necessarily have to be. What can be done to remove the discontinuities that occur between straight lines from each sampling length? A number of attempts have been made. The first is due to Reason [6] who postulated that instead of using a succession of adjacent sampling lengths with lines through each, a multiplicity of sampling lengths of the profile, staggered with respect to each other and consequently overlapping, should be used. The reference line should then be made up from the locus of the mean profile within each sampling length and plotted at the mid-point. This method has therefore been referred to as the “mid-point locus” reference line. It has the considerable advantage that it is unique and gives the same answer as if the center points on center lines or least-squares lines within the samples had been connected up as shown in Figure 2.25. Another advantage of this method is that the center point within each sampling length can easily be obtained from a graph simply by measuring the area between the profile and the bottom of the chart, dividing by the sampling length, and plotting the value in the middle of the sample. The accuracy of the locus is dependent on the extent to which sampling lengths of the profile are allowed to overlap, so obviously there must be a compromise between the amount of labor involved and the accuracy. Five shifts of the averaging box within a sampling length have proved to be reasonable. The shifts are not necessarily equally spaced. The only disadvantage of this method is in its transmission characteristics: they are worst for periodic signals as seen in Figure 2.26. For example, if the locus is plotted on the sine wave then it will undulate unrealistically if the sampling length is not an integral number of wavelengths [15]. It can be shown that if the amplitude of undulation of the locus is taken as a measure of performance and if it is plotted against the wavenumber (not wavelengths) of different sine waves, the resulting curve is that of the sine function S(v) where v is the ratio of the wavelength to sampling length:
0.8 0.6 0.4 0.2 0
–0.2 0.25
0.5 1.0 2.5 Wavelength/sampling length
5.0
10.0
FIGURE 2.26â•… Mid-point locus characteristics.
S (1/v ) =
sin [ 2 π (1/v )] 2 π (1/v )
(2.21)
which for 1/v having a value of 0.66, for instance, gives an undulation amplitude of 19% (see Figure 2.26). Usually the errors are much smaller, especially for random waves. This undulation in the mean line for waves shorter than the sample length looks mechanically unrealistic. In any technique to determine a mean line it is preferable that waves shorter than the sampling length are not distorted. 2.2.1.2.3â•… Spline Functions Another possible way involving polynomials has been suggested which could reduce their shortcomings. In effect what this method does is to apply constraints to the Â�behavior of the reference line at the boundary of each sampling length: rather than allowing the polynomial to have discontinuous height. The method makes use of a variation of a technique used in shipbuilding for many years in the construction of ship outline drawings. A piece of flexible wood called a spline was used to fill in the curved line between the ribs. It has the property that the curve which it takes up between the ends is that of minimum potential energy and whose leastsquares curvature is a minimum. Hence there is the possibility of replacing the succession of discontinuous lines from each sampling length by a “spline function” having welldefined properties. Depending on the type of spline function used discontinuities of height value and differentials are not allowed at sampling length boundaries thereby making a very smooth transition of the reference line between boundaries which means that parameters should suffer less distortion. [15]. A spline utilizes polynomials fitted between what is, in effect, the ribs of the boat structure: it is a function for interpolating the shape between the fixed values given (which are called tabular points although originally as befits a nautical origin involving wood they were called “knots”). If the spline function between M ordinates is φi and the profile is zi then the summation Su in the early days was defined as M
Su =
∑ i =1
( ϕ1 ) + λ 2
M
∑ (ϕ – z ) i
i =1
i
2
(2.22)
21
Characterization
Straight end section
Spline reference line
h(x).λc
1
FIGURE 2.27 End effects of spline reference.
is a minimum, where λ is a constant which has to be fixed. If λ is very large compared with unity then the spline function is nearly a least-squares line. λ has to be chosen to give the correct balance between smoothness and closeness of fit and it corresponds roughly to the elastic modulus of the piece of wood. Any degree of polynomial is possible for use as a spline but it is normal to use cubic degree polynomials which gives the name to “cubic spline.” This produces an interpolated function which is continuous in its second differential through the tabular values except at the end points where it can only be a straight line because there is one fewer constraints. This straight end reference portion is still quite an acceptable reference from which to assess the few end data points of the surface, it also gives the advantage that the end data is used. See Figure 2.27. There are approaches to remove or minimize these end problems for example by Krystek [16]. Much recent work has been done in using spline functions, particularly in numerical interpolation problems involving the generation of continuous surfaces from point-to-point numerical data points, a situation occurring in CAD. Unlike the straight line which has a simple geometric interpretation or filters which can use theoretical spatial weighting functions to describe their characteristics splines have to be described in spatial frequency terms using rather less elegant numerical expressions. For example the Equation h(x) of the cubic spline is given by Equation 2.23 π π h ( x ) = sin 2 mod x + λc λc
π π exp − 2 mod x 4 λc (2.23)
which has a shape shown in Figure 2.28 and is similar to the Fejer kernel, except that negative values are allowed. In Equation 2.23 λc is not the elastic modulus λ corresponding to the wooden spline it is the effective cut-off wavelength of the spline characteristic. It has a frequency transmission characteristic given by Equation 2.24 [18]. See Figure 2.28. 1 TF (ω ) = (2.24) (1 + βα 2 A + (1 − β ) α 4 B ) where α = 1/ 2 sin (ω c ∆x / 2 ) ≈ 1/ω c ∆x for Δx small and 0 ≤ β ≤ 1 and ω c = 2 π /λ c . For the low-pass characteristic this becomes Equation 2.25
1 TF (ω ) = 1 + βα 2 / 4 + (1 − β ) α 4
where α = sin ( ∆xω / 2 ) / sin ( ∆xω c / 2) .
(2.25)
–1
0
1
x/λc
FIGURE 2.28 Spatial function of cubic spline. (From Krystek, M., Measurement 18, 129–138, 1996; After Krystek, M., Advanced Mathematical Tools in Metrology III, World Scientific Publishing, Singapore, 1997. With permission.)
To get the high-pass transmission curve it is unity minus the low pass as they are complementary because there are no phase effects. Also the transmission curve Equation 2.24 has only even powers of frequency because Equation 2.23 is an even function. In general the A and B terms are of matrix form of n × n when the spline is taken across the whole surface of n data points. The diagonal coefficients of the matrix for the case of the non-periodic open profiles i.e., not constrained at the ends, are: A—Second differential three point numerical formula. B—Fourth differential five point numerical formula except for the two points at each end where they resort back to second differentials-due to the fewer constraints. The diagonal coefficients of the matrix for the case of the periodic closed profiles are: A—Second differential three point numerical formula. B—Fourth differential five point numerical formula. In the open and closed profiles above the role of β becomes clear: it, in effect, changes the weighting of the second differential of the curve as operated on by the matrix relative to the fourth differential thereby altering the “rigidity” of the spline. For more information see the works by Krystek [16–18] and ISO/TS 16610-22 [19]. 2.2.1.3 Filtering Methods for Surface Metrology (For methods and definitions according to GPS see ISO/ TS 16610 [19]) The headings are ISO/TS 16610 2006 Part 1 Overview and basic concepts Part 20 Linear profile filters: Basic concepts Part 22 Linear profile filters: Spline filters Part 29 Linear profile filters: Spline wavelets
22
Part 31 Robust profile filters: Gaussian regression filters Part 32 Robust profile filters: Spline filters Part 40 Morphological profile filters: Basic concepts Part 41 Morphological profile filters: Disc and horizontal line-segment filters Part 49 Morphological profile filters: Scale space techniques Under preparation; Part 21 Linear profile filters: Gaussian filters Part 26 Linear profile filters: Filtration on nominally orthogonal grid planar data sets Part 27 Linear profile filters: Filtration on nominally orthogonal grid cylindrical data sets Part 30 Robust profile filters: Basic concepts Part 42 Morphological profile filters: Motif filters Part 60 Linear areal filters: Basic concepts Part 61 Linear areal filters: Gaussian filters Part 62 Linear areal filters: Spline filters Part 69 Linear areal filters: Spline wavelets Part 70 Robust areal filters: Basic concepts Part 71 Robust areal filters: Gaussian filters Part 72 Robust areal filters: Spline filters Part 80 Morphological areal filters: Basic concepts Part 81 Morphological areal filters: Motif filters Part 89 Morphological areal filters: Scale space techniques. 2.2.1.3.1â•… Historical Perhaps the easiest way to separate the components of a signal on a frequency basis is by the use of filters. They have one big advantage over polynomial-type curve fitting: within generous limits little prior knowledge of the input waveform is required. The filter takes the waveform “as received” and then operates on it: the resultant waveform has less information but what is left is more specific to a given application. (Filtration is defined in ISO/TS 16610-1 as “operation used to create an ideal feature by reducing the level of information of a non-ideal feature” which shows the difference between an engineering definition and a mathematical one!) What happens in order to pay for this apparent freedom is that a certain amount of the input information has to be used up by the filter before it can give useful outputs; it needs time (or data) to get the “feel” of the input signal. Therefore the amount of usable data is reduced at the expense of versatility of operation. Filters have been used since the earliest days of surface metrology as a prerequisite to making meaningful measurements of any parameter. The first sort of filter network used in this respect was a single CR network. Contrary to present day belief the original electrical filters were not introduced to remove waviness from the surface measurement signal but were put in to minimize set up problems. In the first instance a skid was attached to the pick-up arm in front of the stylus to act as an intrinsic reference thereby enabling the surface signal to keep within the range of the transducer even if the part were badly tilted: this meant that all the surface signal was obtained
Handbook of Surface and Nanometrology, Second Edition
during a traverse. This is because if the workpiece was tilted relative to the normal traversing reference a DC signal was produced which swamped the variations due to the roughness and spoiled the value of any parameter obtained from it which was displayed on the meter. A single stage CR filter was inserted into the transducer circuit to remove this DC term yet allow the roughness signal through. This was a considerable improvement but it still allowed a DC term into the signal if the workpiece had a curvature, so another CR filter was added to take this eventuality into account. These modifications enabled meaningful parameters to be read from the meter but as will be seen they made it difficult to tie up the meter reading to that obtained graphically from the chart. The characteristics of this 2CR filter are such that if z is an input profile sinusoidal signal of wavelength λs and if λc is the cut-off wavelength taken to be at 75% transmission (Figure€2.29) then the transmission is given by transmission (%) =
1 1 + 13 ( λ s /λ c )
2
(2.26)
The 2CR characteristic was chosen for convenience and simplicity and to allow measurement with a skid. The value of 75% adopted for the cut-off itself is a compromise value. In the earliest instruments the British chose 80%, the Americans 70.7%. In the end, to make the instruments compatible, 75% was used. This is purely arbitrary but it turned out to be reasonably practical. The earliest filters used electrical components such as resistors and capacitors to produce the desired effect. Later instruments used digital methods. This type of transmission curve and the 75% cut-off was referred to as the “standard filter” and was the preferred filter for many years as set down in international and national standards. Other filters and cut-off percentage transmission values are recommended today but this does not detract from the usefulness and practicality of the original standard filter which is still in use in many instruments. Because the filter has been designed to simulate the graphical method, λc is taken to be equal to the sampling length mentioned in Section 2.2.1. The three different cut-off wavelengths have been recognized 2.5, 0.8, and 0.25 mm, these roughly representing the boundaries of waviness found by experience for manufactured surfaces and were nominally 100%
75%
0%
λc
λ
FIGURE 2.29â•… The “standard filter” transmission characteristics.
23
Characterization
chosen by Reason to have a ratio of √10 which is still used today and was the basis for the transmission characteristics of the first phase corrected filter proposed by Whitehouse, as described later. In what follows the 75% transmission characteristic will be used initially because this characteristic was in most early instruments from which examples were drawn. The new recognized transmission at the cut-off is 50%. This will be introduced later. Comparison of many Ra values worked out graphically and those obtained by filtering shows that the decision to make the cut-off wavelength of the filter equivalent to the sampling length on the graph was justified. Differences of more than 5% are rare. Such correspondence is not of the same order if other parameters such as Rt or Rp, for example, are being measured. The filter characteristics given by Equation 2.26 are meant to be those of the instrument as a whole and not of any constituent part. The characteristics constitute therefore an instrument transmission curve, and so for a stylus instrument the characteristic should be taken as the way in which sinusoidal displacements at the stylus are revealed at the output. All frequency cut-offs, for example in amplifiers, recorders, etc., should be taken into account. For most modern instruments these all tend to fall well outside the range of wavelengths under consideration and as a result negligible error is introduced by incorporating the simple two-stage filter having the desired characteristic. The way in which filters work on the surface profile waveform has to be understood, especially for the earlier type of filter. This is because not only are amplitudes modified but a certain distortion of the wave occurs due to phase shift. This is not a problem in the later digital filters but nevertheless it has to be demonstrated so that discrepancies between old and new instruments can be understood and taken into account. How such a “standard” filter produces a mean line can be seen in Figure 2.30. In this figure the upper graph shows the input signal and the bottom shows the output. Between these is the
profile signal but this time it has had the difference between the other two graphs plotted as a broken line. This line represents the low-frequency signal being blocked by the filter; this blocked signal is the reference line from which the surface parameters can be measured. There is a difference between filter techniques and other methods, which is that in its simplest analogue form the filtering technique is time dependent. The behavior of the filter is determined by the time dependence of the signals passing through it. The wavelength on the surface of these signals has to be related to time by the scan rate of the instrument. Thus the frequency resulting from a wavelength λs is given by f = s/ λs where s is the speed of traverse. This time dependence used to be a serious problem but it is not so today because the behavior of the filter can be exactly reproduced by a mathematical technique first evaluated by Whitehouse [20] in 1965 which, like all the previous reference lines, can be purely spatial. Ideally all procedures in surface metrology should be spatial and not temporal. The benefit of using filters, apart from their impartiality in dealing with all incoming signals, is their ease of use and cheapness. The standard 2CR filter does, however, suffer from some disadvantages over other methods. Examples of this are shown in Figures 2.31 and 2.32. (a) λ/λc 1/3 1/2 2/3 1 2 (c)
Surface profile
(e) Mean line
Waviness
Rt
Roughness parameter
Ra/Rt (b) Transmission % 1/3 96 96 1/2 92 92 2/3 87 87
98 91
1
82 51
75 75
43 43
96 96
2 (d)
Ra/Rt 93 83 90 72 50 33
96 97
92 92
91 92
87 87
84 88
75 75
75 79
43 43
38 50
100 100
(f)
100 100
100 100
100 100
100 100
100 100
100 100
100 100
43 43
19 38
Ri R a Rt Zero line Sampling length
FIGURE 2.30 Relation of mean line to profile.
Ra Rt
FIGURE 2.31 Effect of phase correction on standard shapes: (a) standard filter, sine wave profile, (b) standard filter, triangular profile, (c) and (d) phase-corrected standard filter, (e) and (f) phasecorrected linear profiles.
24
Handbook of Surface and Nanometrology, Second Edition
Turned
Ground
Blast
FIGURE 2.32 Comparison between figure standard and phasecorrected filters.
When a profile signal has significant components with a wavelength near to that of the cut-off of the filter a certain amount of distortion can arise. The output signal no longer closely resembles the input waveform. This is due to phase shift. What happens is that some components of the profile get shifted relative to each other in their passage through the filter [20,21]. At the same time some get attenuated according to where their wavelengths fall on the transmission curve of Figure 2.29. A mathematical way to correct the phase distortion was achieved by Whitehouse [21] in 1965 although the solution was not published until 1967. He coined the new filter name “phase corrected” which is now extensively used in surface metrology and he also correctly assigned this metrology filter to the class of linear phase. His solution has also linear spatial frequency attenuation characteristics in transmission. Apart from the visual distortion of the profile which can sometimes result from this effect, parameters measured from the output waveform can also be in error. Fortunately this effect is not serious in the case of a Ra measurement but it is, or can be, important in the case of Rp or Rt, for example. It is fundamental when peak curvature or similar parameters are being measured for tribological experiments. This is why phase distortion of surface data occupies such an important position in surface metrology. Another problem associated with the standard filter emerges in the problem of calibration. Because the standard filter has a rather gradual transition from the nominal “pass” band to the nominal rejection region and because of the phase distortion the calibration of instruments can be difficult. In order to elucidate the nature of subsequent improvements to the assessment of parameters, the manner in which the standard filter responds to some idealized repetitive waveforms will be considered. This is because the standard wave filter is generally satisfactory for random roughness waveforms. Repetitive waveforms tend to accentuate any shortcomings. Look first at Figure 2.31a which shows how the standard filter responds to sine waves. The figure shows sine waves of different wavelengths. The full line shows the original wave and the dotted line is the mean line found by the wave filter, this being the line that accounts for the output behavior. The difference at any instant between the two lines is the filtered profile
value. The top four graphs show sine waves within the pass band; notice that the mean line is displaced to the right relative to the original sine wave in all cases, which means that it is delayed in time relative to the profile, and further that the mean line has a large amplitude of undulation even for wavelengths much smaller than the cut-off, for example for one-third of the cut-off (the top graph). Another point is that the amplitudes of the mean line can be of the same order as the original sine wave, even just outside the pass band. Despite these points the filtered profile, which is the difference at any position between the mean line and the profile, obeys exactly the specified amplitude transmission characteristic mentioned previously. As an example, at the cut-off the mean line has an amplitude of just over 90% of the original sine wave profile, but the filtered profile has the “correct” amplitude of 75% of the amplitude of the profile. (Using the old cut-off transmission percentage. The amount by which the mean line is shifted relative to the profile depends on the wavelength of the sine wave profile. For most commonly used filters, specifying the amplitude transmission characteristics automatically fixes the phase characteristics. This class is known as minimum phase [16], of which the standard filter of 2CR networks is a typical member [16]. Specifying the transmission characteristics for the standard wave filter automatically implies a phase-shifted mean line. Suppose that a filter is available which has the same transmission characteristic as the standard filter, but at the same time has a mean line which is not shifted in phase relative to the profile. How is the mean line amplitude affected? This situation is shown in Figure 2.31c for the same sine waves as in Figure 2.31a, and for triangular waves in Figure 2.31d corresponding to Figure 2.31b. It can be seen that the mean line is nearly straight at one-third of the cut-off. Compare this with the same profile for the standard wave filter. There is a dramatic reduction in the amplitude of the mean line, and this is true for all the cases shown. At the cut-off, the filtered profile for this new filter has the required amplitude of 75% of the profile—the 25% attenuation is accounted for entirely by the amplitude of the mean line. In other words, if the mean line is kept in phase with the sine wave profile, then, for the value of wavelength, the maximum amplitudes of the filtered profile, and the mean line add up to unity, a criterion which does not hold in the case of the phaseshifted mean line. A direct result of this is that the mean line in phase with the profile undulates less. Summarizing, it may be said that the mean line becomes straight much nearer to the cut-off in the filter whose mean line is in phase than it does in the standard wave filter, although the filters have precisely the same amplitude transmission characteristics. This fact is of fundamental importance. It means that the shape of the roughness can be preserved even in the presence of considerable waviness and form error. Hence the roughness parameters retain their credibility throughout the filtering process. For a sine wave profile the phase distortion simply takes the form of a phase shift of the filtered profile relative to the original profile, but for any other profile that can be considered
Characterization
to be made up of a number of such sine wave components, the distortion is more complicated. Consider now triangular waveform profiles of differing wavelengths. Remembering that the filtered profile is the difference at any point between the mean line and the profile waveform, it can be seen that the filtered profile for the zero phase-shifted mean line (phase corrected) bears a much closer resemblance to the original waveform than it does for the standard wave filter [21]. The zero-phase (phase corrected) filter has a more realistic mean line because the sine wave components making up the triangular waveform are not shifted relative to each other in the filter. Consequently, the components have the same relative positions upon emerging from it. Hence, even taking account of those components that have been attenuated in the filter, the output still resembles the input. This is not so true in the case of the standard wave filter. Distortion of the filtered profile can make it difficult to assess numerically. This is the problem that can be encountered in practice when highly repetitive profiles just within the pass band are put into the standard wave filter. As an example, the triangular waveforms shown in Figure 2.31c are a close enough approximation to a practical waveform to illustrate how the problem arises. Consider the filtered profile in Figure 2.31a; the concept of a peak output at the cut-off, say, is difficult to imagine—the peak shape has virtually disappeared. Now look at Figure 2.31b and c where the peak is noticeable and unambiguous to measure. So far only the phase characteristics have been considered. There remains the problem of deciding on a suitable transmission characteristic. This is not easy, for it has to be remembered that a good reference (or mean) line has to be realistic for waviness as well as for roughness. Another point is that transmission characteristics for surface filters are plotted as transmission percentage as a function of spatial wavelength, not frequency as is conventional. This adds some complications. Take as a start an ideal roughness filter, that is one where waviness is not considered except to be excluded. The original ideal for this type of filter, known as the Whitehouse filter, is outlined below. The mean line is straight for all wavelengths within the pass band of the filter, that is up to the cut-off. This would mean that the profile would suffer no attenuation for wavelengths up to the cut-off. From the point of view of surface roughness measurement this seems sensible, because it is natural to suppose that if a cut-off has been chosen for the filter of a value larger than the longest roughness wavelength on the surface, then all the roughness will be passed unattenuated. Another point about the transmission characteristics which can be mentioned concerns the behavior outside the cut-off. Although the behavior outside the cut-off is not as important as that within the cut-off, it still has some relevance to the measurement of the roughness. The standard wave filter tends to fall off too gradually for wavelengths longer than the cut-off, with the result that waviness components can be included in the roughness assessment: a point which is also true for the Gaussian filter described below. From these factors it appears that an amplitude transmission characteristic which is unity up to the cut-off wavelength
25
and which falls rapidly after the cut-off would be more suitable for roughness measurement. Excessively high rates of attenuation, however, could be unrealistic mechanically because a considerable variation is not expected in the functional behavior of, say, two surfaces having a roughness of equal amplitude but slightly different wavelength. One such characteristic that has seemed practical is one having unity transmission up to the cut-off which then falls off to zero at three times the cut-off, the rate of attenuation being linear with spatial frequency. This has the merit of being compatible with the long-established sequence of sampling length cut-off values although the rate of attenuation can be changed to suit the manufacturing process. Figure 2.31e and f shows how a filter having an in-phase mean line similar to the one mentioned previously, but having the new transmission characteristics, behaves with the sine and triangular waveforms. The figures show a straight mean line right up to the cut-off and no distortion of the filtered profile. This is what could justifiably be called a filter with a well-behaved mean line. This filter will be referred to as the Whitehouse phase-corrected filter [21]. So far only idealized waveforms have been shown. In fact these accentuate the difficulties encountered in practice. Mean lines, as a rule, do not oscillate with such a large amplitude for practical waveforms within the cut-off even for periodic profiles, because a random component is always present. In the case of profiles which are random, the undulation of the mean line and the distortion of the filtered profile from the standard wave filter are not so obvious. The majority of profiles of this type have realistic mean lines, providing that the longest spacings are short compared with the cut-off length. However, for the standard wave filter the distortion of the filtered repetitive profile and the undulation of the mean line have presented a serious enough problem in some instances to warrant correction. Some practical profiles are shown in Figure 2.32, together with a comparison of the mean line found by the standard filter and the phase-corrected filter. They show that the phasecorrected filter has advantages over the standard wave filter in a number of ways. The gain is usually greatest when other factors apart from roughness measurement have to be considered, such as only a small amount of available traverse or waviness components lying near to the dominant tool marks on the surface. In fact, the advantage is usually greatest in cases where it is impossible, for one reason or another, to choose a cut-off for the standard filter long enough to make phase distortion negligible. Many of the parameters used to measure roughness, such as the maximum peak or valley value, the derivatives or the bearing ratio curve, are affected by phase distortion. Center line average Ra is affected to a lesser extent, while RMS, Rq and some related parameters are not affected at all. The roughness which is transmitted by the phase-corrected filter actually looks like the roughness on the original profile and it is a sensible precaution to measure any desired parameter, even for waveforms containing components near to the cut-off. Another point is that the mean line for components within the cut-off is straight, with the result that all roughness
26
Handbook of Surface and Nanometrology, Second Edition
within the cut-off is assessed. Yet another possibility offered by this filter is that the mean line of the roughness found by its use could properly be regarded as the waviness. The characterization of the surface geometry taken as a whole therefore becomes a realistic possibility. Having the capability just to measure the roughness alone does not allow this vital possibility. This is because the shape of the mean line is only affected by components outside the cut-off (which are usually due to waviness) and also because the mean line will be in phase with these components. The mean lines for the repetitive waveforms outside the cut-off can be seen in Figure 2.31c. Figure 2.32 shows how the mean lines for practical profiles look convincing for the waviness.
shown next that the time variable t can equally be replaced by a spatial variable (as indeed it can be replaced by a numerical variable in a computer) without loss of generality. The effect of different filters can therefore be visualized for the metrologist. It also relates more nearly to the concept of functional filtering in tribology where the weighting function can be a contact pressure distribution. Equation 2.29 is important because it shows that the frequency characteristics of a filter are tied down to the shape of its impulse response: altering the impulse response alters the frequency characteristics. The impulse response can alternatively be expressed in terms of a fraction of the time constant of the filter which, in turn, can be expressed in terms of a fraction of the sampling length when referred to the profile. This has the advantage of making not only the weighting function but also the variable in the superposition integral non-dimensional as well as relating more directly to the surface.
2.2.1.3.2 Filter Theory Applied to Surface Metrology The frequency characteristic (or Fourier transform) H(ω) of a filter can be expressed in terms of the angular frequency ω as
H (ω ) = k ( ω ) exp ( jφ ( ω ))
(2.27)
where k(ω) is the amplitude transmission characteristic and f(ω) is the phase. The problem in surface metrology is to get a useful form for k(ω) whilst maintaining a form for f(ω) which eliminates phase distortion. This is true for roundness, roughness, and all other metrology issues. The impulse and step responses of a filter are a means of explaining how the filter behaves when it is subjected to a signal. The output of a filter in general terms is given by the superposition integral which, in effect, says that the output at any time is given by the convolution of the input signal with the impulse response of the filter. Thus
g(t ) =
∫
t
−∞
f (τ)h(t – τ)dτ
(2.28)
H (ω ) =
∫
∞
h(t )exp(– jωt ) dt
-∞
(2.29)
and
G (ω ) = F (ω ) H (ω ).
The idea of the weighting function is very important in the application of filters to surface metrology problems because it enables the behavior of a filter in time to be visualized as if the filter was acting on the profile on the chart. It will be
(2.30)
where H(p) is for a low-pass filter and p is the Laplace operator. Low pass (b) Origin
6.0
g(t ) = f (τ) ∗ h(t )
where f(τ) is the input signal, g(t) is the output, and h(t) is the impulse response. In Equation 2.28, h(t–τ) the reversed impulse response, is sometimes called the weighting function of the filter. If H(ω), G(ω), and F(ω) are the Fourier transforms of h(t), g(t), and f(τ), respectively,
H ( p) = 1 − H ( p)
(a)
or
2.2.1.3.3 Impulse Responses and Weighting Functions Consider the low-pass filter in Figure 2.33a. It attenuates high frequencies. When referred to the time domain it means that the impulse response actually spreads in time. Because of this the impulse response tends to average out the high frequencies in the input waveform during the convolution process. For the high-pass filters in Figure 2.33b the situation is different because an impulse is present in the impulse response, which is opposed by a low-pass component. If the transfer – function of an ordinary high-pass filter is H(p) it can be written in the form
4.0
Axis of symmetry
2.0 0 (c) 0
α 1.0
2.0
Unit impulse 1.0
2.0
0 High pass (d) α
1.0
2.0 Unit impulse
α 1.0
α 2.0
2.0 4.0 6.0
FIGURE 2.33 Original (a) and phase corrected (b) weighting function for the standard filter mean line, (c) and (d) the respective impulse responses.
27
Characterization
Equation 2.30 inverse-transforms into an impulse response h(t), h(t ) = δ − h(t )
(2.31)
where h(t) is the impulse response of the low-pass component and δ is an impulse at the origin of unit weight. A signal f(t) put into a high-pass filter gives an output g(t ) = =
∫
t
∫
t
h(t − τ) f (τ)dτ
−∞
(2.32)
∫
δ(t − τ) f (τ)dτ −
−∞
t
t
g(t ) = f (t ) −
∫
h(t − τ) f (τ)dτ = f (t ) − m(t ). (2.33)
−∞
∫
α
0
δ(α − α ′) f (α ′)dα ′ −
∫
α
0
h(α − α ′) f (α ′)dα ′
= f (α) − m(α).
(2.34)
In Equation 2.34 α′ is a variable similar to τ in Equation 2.32, that is h(α) = δ′–h(α) where δ′ and h(α) have unit weight when integrated with respect to α. For the standard wave filter
h (t ) = δ (t ) −
1 t t 2− exp − RC RC RC
(2.35)
or
H (ω ) = k (ω) exp( jϕ (ω ) = R(ω ) + jx (ω ),
(2.36)
h (α ) = δ ′ − A(2 − Aα )exp(− Aα )
where A = λ/s RC (λ is the sampling length and s is the tracking speed) and α = x/λ where x is the distance along the surface. In Equation 2.35 both parts have the dimensions of reciprocal time whereas they are dimensionless in Equation 2.35, which means that the ordinate scale does not change with the cut-off. The factor 1/Tc is taken into the variable dα′ of Equation 2.35 where Tc is the equivalent time of the sampling length.
tan –1
X (ω ) . R(ω )
So X(ω) the imaginary component, would have to be zero in Equation 2.36 to make the phase zero, leaving
In practice the lower limit of the integral can be taken to be zero. Electrically m(t) is the signal blocked by the filter. In surface metrology m(t), when referred to the profile graph, is the mean line. The removal of m(t) from the input profile constitutes the high-pass filtering action; h(t–τ) is the weighting function of the mean line. Equation 2.33 can be expressed in a form more suitable for surface metrology by changing the time axis to a nondimensional fraction of the sampling length α: g(α) =
where φ, the phase angle, is given by
h(t − τ) f (τ)dτ
−∞
But ∫−∞δ ( t − τ ) f ( τ ) dτ = f ( t ) because of the sampling property of impulses. Hence Equation 2.32 becomes t
The phase characteristics of a filter effectively show how sinusoidal signals get shifted in time in their passage through the filter. The real criterion for the filtered profile to be undistorted is that the constituent sinusoidal components making up the profile are not shifted relative to each other during the passage of the profile through the filter. One method of doing this would be to ensure that none of the components got shifted at all. This would mean that the phase shift is zero for all frequencies. Now
H (ω ) = k (ω) = R(ω ).
(2.37)
But, for the transmission characteristic of the filter to be real, the impulse response must be an even function (i.e., symmetrical about the time origin axis), which is impossible in practice because the impulse response or the weighting function of the filter cannot extend into the future as well as into the past. Hence, the only possibility of getting no distortion of the filtered profile is to arrange that the wavelength components of the profile are all shifted by the same amount in time by the filter. Suppose that this meant delaying all components by t0. One component at angular frequency ω1, say, would have to be shifted in phase by –ω1 t0 rad to get this delay. A component of angular frequency ω2 would have to be shifted by –ω2 t0, and similarly for any component. In fact, to satisfy this delay of t0 in general f(ω) = −ωt0; the phase has to have a linear relationship with frequency. Therefore, the transmission characteristic for a filter having no phase distortion but a delay is of the form
H (ω ) = k (ω)exp(− jω t0 )
(2.38)
Such a filter is called a linear phase filter. It took a long time in surface metrology to realize the potential of such filters! How do the impulse responses of the zero-delay and linear phase filters compare? It is easy to show that if h 0(t) is the impulse response of the zero-delay filter, then the impulse response of the linear phase filter having the same amplitude transmission is h 0(t–t0). This means that they have the same shape, but the linear phase impulse response is shifted by t0 along the positive time axis—they both have a symmetrical weighting function but the zero-delay impulse response has its axis of symmetry on the time origin, whereas the linear phase impulse response has the axis of symmetry at t = t0. Shifting the axis of symmetry to t0 makes the impulse response practically realizable. Summarizing, it may be said that it is possible practically to make a filter giving no phase distortion only by allowing a uniform delay of all components
28
Handbook of Surface and Nanometrology, Second Edition
passing through it. This is achieved by a filter having linear phase characteristics, which implies that it has an impulse response which is symmetrical about an axis of t = t0 on the realizable side of the time axis. In the non-dimensional form t0 becomes a (Figure 2.30d). If
and those which have Gaussian and raised cosine impulse responses. Perhaps one of the most obvious is the linear phase filter having the same amplitude transmission as the standard filter. It has an impulse response
h0 (t ) ⇔ H 0 (ω )
(2.39)
h0 (t − t0 ) ⇔ H 0 (ω )exp(− jω t0 ).
hL (t ) = δ ( t − t0 ) − h0 ( t − t0 ).
(2.40)
g(t ) = f (t − t0 ) −
∫
t
0
h0 (t − t0 − τ) f (τ)dτ .
(2.41)
Equation 2.40 shows that the impulse component lies at the axis of symmetry of the low-pass impulse component, which means that in terms of Equation 2.40 the signal itself has to be delayed by t0 before taking it from the low-pass component. This has the effect of producing, at time t, the filtered output— without distortion corresponding to the profile at tâ•›– t0. Two points are worth noting concerning symmetrical impulse responses: one is that the step response has an axis of odd symmetry about t = t0, and the other is that the operations of correlation and convolution become the same except for an averaging term. 2.2.1.3.4â•… Phase Corrected Filters Phase corrected filters: the original term used by Whitehouse in 1965 which has now been adopted by the metrology community as most descriptive of their behavior: these are also named in electronic texts as linear phase filters (Figure€2.32b). The conditions for a symmetrical weighting function to be suitable are the following:
(2.42)
1. It has an axis of symmetry later than t = 0 to an extent such that no considerable part of the function crosses the t = 0 axis. 2. It is concentrated in a central lobe and dies away quickly on either side of the axis of symmetry. 3. Any negative portions should be small. 4. It must have an amplitude transmission characteristic suitable for use in surface metrology.
A number of different linear phase filters have been investigated, including the ideal infinitely sharp cut off Figure 2.34
π 2π exp − | α − α 0 | (2.43) 3 3
where the latter expression puts the impulse response in nondimensional form, ωc is the angular frequency equivalent of the sampling length, and α is the position of the axis of symmetry—equivalent to t0. Another alternative is the ideal linear phase high-pass Â�filter where h (t ) = δ(t − t0 ) −
Equation 2.33 becomes for a linear phase filter
h (α ) = δ ′(α − α 0 ) −
For the zero-delay case the high-pass impulse response h 0 (|t|) can be expressed as δ–h 0 (|t|), where h0(|t|) is the lowpass impulse response and δ is an impulse at the origin. The corresponding linear phase high-pass impulse response hL(t) is therefore given by
ωc ω exp − c t − t0 π 3 π 3
or alternatively
then
h (t ) = δ(t − t0 ) −
sin ω c (t − t0 ) π(t − t0 )
(2.44)
sin 2 π(α − α ) . π(α − α)
(2.45)
or h (α ) = δ ′(α − α ) −
These, however, did not seem to be as suitable a starting point as the Whitehouse filter, which has unity transmission for wavelengths up to the cut-off and zero transmission at three times the cut-off. The attenuation rate is proportional to the equivalent frequency. The expression “phase-corrected filter” has a slightly different connotation in communication theory, but it is useful in this context. The general equation for impulse responses having this linear amplitude form is h (t ) = δ(t − t0 ) −
×
2 πω c (1 − B)
sin [ ω c (1 + B)(t − t0 ) / 2 ]sin [ ω c (1 − B)(t − t0 ) / 2] (2.46) (t − t0 )2
or h (α) = δ ′(α − α) −
×
1 π (1 − B) 2
sin [ π(1 + B)(α − α) ]sin [ π(1 − B)(α − α) ] , (2.47) (α − α )2
where B is the ratio of wavelengths having unity to zero transmission, being equal to 1/3 in this case. Other possible filters have been examined such as those in which the attenuation characteristic is linear in wavelength rather than frequency as it is in Equation 2.25. This is a natural extension to the filters for use in surface metrology because surfaces are spatial not temporal in character.
29
Characterization
From what has been said it is possible to set down some characteristics that would be suitable for a filter having these properties. It would have the transmission characteristic F(λ) given by Equation 2.48 1 F (λ ) = P (λ ) 0
λ s < λc λ c < λ s < Kλ c Kλ c < λ s .
(a) Transmission 1.0
(2.48)
0
In the case shown above F(λ) is usually expressed in terms of frequency for reasons which will become obvious. Thus, if frequency fc corresponds to 1/λc, F(f) corresponds to F(λ) and Ka corresponds to 1/K: F( f ) =
K a f − fc . ( K a − 1) fc
Transmission
1.0 Gradual
Ideal 1.0
FIGURE 2.34â•… Linear phase-corrected filter characteristic.
ω
Frequency
Cut-off
(b) Transmission 1.0
Roughness
(2.49)
In the filter example chosen as typical Ka = 3. Over the range fc/Ka < f < fc the characteristic is linear with change in frequency, or F(λ) = (λK–λc)/λ(1–K) over the range λa < λ < Kλc i.e., P(λ). The phase shift is ideally zero as is seen from Figure 2.32. This implies that the imaginary part of the filter characteristic should be zero, that is phase Φ(f) = X(f)/R(f) for a general filter; this is only zero if X(f) is zero. What this means and how it is achieved will be seen in the next few pages. The Whitehouse phase-corrected filter has characteristics which are virtually ideal for roughness but not for waviness (Figure 2.34). In many instances this does not matter. However, in order to make the roughness and waviness filters complementary (i.e., always add up to unity) the cut-off has been repositioned to be 50% rather than 75% and the transmission characteristic gradual rather than sharp as advocated by Whitehouse. This means that, at the cut-off, both waviness and roughness will be transmitted. The new preferred filter has nominally Gaussian characteristics rather than the standard phase-corrected filter or Whitehouse phase-corrected filter. In order to understand the implications of this some idea of how filters work will be considered. The concepts here will be referred to many times in the text because the decomposition of the surface geometry into components is functionally important and filtering is a preferred way of doing it. Notice that there are benefits in symmetry which can be obtained by using linear relationships in the transmission
0
Roughness
Waviness
0.5
Waviness
0.5
0
Cut-off
Wavelength
FIGURE 2.35â•… Phase-corrected (a) linear frequency and (b) linear wavelength characteristics.
characteristics; see Figure 2.35 the roughness and the complement of it, the waviness. Both have the same form. Also, a not insignificant advantage is that the rate of attenuation can be adjusted, subject to agreement, to fit specific process requirements. For example in the case given above with plateau honing, as there is a virtual separation between the frequency bands of the fine honing marks and the spectrum of the scratches the rate of attenuation can be made to cut between the two thereby separating out the fine and rough Â�components of the manufacturing process: a feature not possible with the standard or Gaussian Â�filters. The linear frequency characteristics can be adjusted in the frequency domain trivially. The impulse response of the linear amplitude filter is a bit more complicated than that of the linear frequency version but this is not a problem. It is, for completeness, given by Whitehouse [22] h (α ) = δ (α ) −
λL 1 2πα sin 1− πα λU λU − λ L
−
1 2 πα λ L πα λ L λU − λ L
+
2 2 πα 2πα Ci − Ci . (2.50) λ L λU − λ L λU
Where λU and λL are the upper and lower wavelengths, respectively, as a fraction of the cut-off and Ci(–) is the cosine integral. This should be compared with Equation 2.47 for the linear Â�frequency alternative. The format is slightly Â�different. The desirable transmission characteristics of the sharp cut-off filters have to be balanced by the associated long impulse responses so some truncation is usually imposed. See Whitehouse [21].
30
Handbook of Surface and Nanometrology, Second Edition
2.2.1.3.5╅ Gaussian Filters In these filters the formulae for the weighting functions and the transmission characteristics are very different (see Table€2.8). It seems plausible to consider a filter system which has virtually the same form of equation in both time (or spatial distance along the profile) and frequency (or spatial frequency). This is in fact easily done by making the shape of the weighting function Gaussian. The frequency characteristics of this in terms of amplitude are also Gaussian because the Gaussian shape is its own Fourier transform. Unfortunately surface metrologists work in wavelengths, so the transmission characteristic (in wavelength terms) of a Gaussian weighting function is not itself Gaussian. It is, however, recognizable as being derived from a Gaussian weighting function and has been selected as the new preferred filter. (See below for the background.) See ISO/TS 16610-31 for Gaussian filter. Also, in order to match the waviness and roughness roles the cutoff is at 50%. Incidentally other functions f(t) which have the shape duality between the time and frequency transforms can be found by solving the differential equation [23]
than those given above. Although the Whitehouse phase corrected filter fitted into the role of the new generation of filters for roughness it was criticized for being too complicated: the weighting function is not straightforward. It was argued that it would be very difficult to implement in a computer. This was considered to be a valid criticism at the time when the true flexibility of computers was not properly appreciated. As an alternative Whitehouse mentioned that invoking the central limit theorem could provide an option which in this context meant that if a box function such as that used in the mid-point locus method i.e., an averaging function is swept through the surface data signal a number of times backward and forward the effect is to produce a Gaussian weighting function and therefore would be very cheap to incorporate into a computer. In fact using only three sweeps gives a function which is within 1% or 2%. See Figure 2.36. In practice, of course, any shape of weighting function can be easily generated and used in a computer. Unfortunately the Gaussian weighting function applies only to the low pass characteristic. i.e., the waviness. Strictly, in temporal terms the low pass is Gaussian the high pass is unity minus Gaussian which is not the same shape. Also as already mentioned the Gaussian shape is restricted to the frequency transform not the wavelength transform. Notwithstanding these flaws instrument manufacturers particularly in Germany took up the idea reasoning that the Gaussian function is well known to metrologists, it being present in many aspects of
d 2 f (t ) 2 − t f ( t ) = − ( 2n + 1) f ( t ). dt 2
(2.51)
Historically the Gaussian shape for the surface roughness filter weighting function came into being for a different reason
TABLE 2.8 Filter Designations ISO Listing ISO/TS 16610-1 Type FA
Category FAL
FAM
FAR FP
FPL
FPM
FPR FP (special case)
Designation FALG FALS FALW FAMCB FAMCH FAMOB FAMOH FAMAB FAMAH FARG FARS FPLG FPLS FPLW FPMCD FPMCH FPMOD FPMOH FPMAD FPMAH FPRG FPRS F2RC
Name Gaussian Spline Spline wavelet Closing ball Closing horizontal segment Opening ball Opening horizontal segment Alternating series Ball Alternating series horizontal segment Robust Gaussian Robust Spline Gaussian Spline Spline wavelet Closing disk Closing horizontal segment Opening disk Opening horizontal segment Alternating series disk Alternating series horizontal segment Robust Gaussian Robust Spline 2RC
ISO document ISO/TS 16610-61 ISO/TS 16610-62 ISO/TS 16610-69 ISO/TS 16610-81 ISO/TS 16610-81 ISO/TS 16610-81 ISO/TS 16610-81 ISO/TS 16610-89 ISO/TS 16610-89 ISO/TS 16610-71 ISO/TS 16610-72 ISO/TS 16610-21 ISO/TS 16610-22 ISO/TS 16610-29 ISO/TS 16610-41 ISO/TS 16610-41 ISO/TS 16610-41 ISO/TS 16610-41 ISO/TS 16610-49 ISO/TS 16610-49 ISO/TS 16610-31 ISO/TS 16610-32 ISO 3274
31
Characterization
1.0
Waviness
Weighting function
Waviness
Roughness
1.0 1
(a)
(b)
–1
(c)
FIGURE 2.36 Repeated convolution of box function soon produces Gaussian function shape.
quality control and so would be readily accepted which it turns out has been the case! Thus the weighting function is
α 2 1 h(α) = exp − π α1λ c α1
(2.52)
(Putting the transmission characteristics in terms of α gives H(1/α) as
2 1 α H = exp − π 1 . α α
(2.53)
This gives the amplitude of the sinusoidal signal of wavelength α1
α1 =
ln 2 = 0.469. π
(2.54)
0
+1
(2.55)
Compare Equation 2.54 with Equation 2.55. Immediately it can be seen that Equation 2.54 is not an even function about the cut-off so that the curves in Figure 2.37 are not the same, also, both have an exponential term with a negative squared argument but this does not make them both Gaussian because in the latter case the numerator is in the argument. It is possible to compute filters using methods other than the obvious convolution method described above. In particular it is relatively easy to compute a complete spectrum using a fast method such as the Fast Fourier Transform (FFT) devised by Cooley and Tukey in which the transmission characteristics can easily be altered. Many variants on the standard filter and phase-corrected filter are possible. Filtering using a phase-corrected method has its problems if characteristics such as those outlined in Equation 2.49 are to be used. This is because of the sharp attenuation drop-off. As this is faster than the Gaussian characteristic the impulse response tends to be slowly decaying, with the result that some degree of truncation of the weighting
α
λ
FIGURE 2.37 Gaussian filter with attenuation curves.
function has to be allowed for in the computer. This produces problems in standardization for instrumentation. The alternative is to limit the weighting function arbitrarily to a known extent, for example to use a box function (as in the mid-point locus method) or a triangle. The other problem is that such amplitude characteristics do not lend themselves well to recursive filtering techniques. Despite the fact that the Gaussian filter characteristic has been adopted by the standards committees there is not a convincing case for its superiority over the linear filter characteristic. The basic premise that the roughness filter is Gaussian when derived from the Gaussian weighting function is not true yet this was regarded as its principal attributes, neither is it true that it has a symmetrical arrangement with the waviness filter. 2.2.1.3.6 Regression Filter This modifies the mean line to enable the end points to be utilized. A typical regression is n
The transmission of the roughness profile is complementary to that of the transmission of the mean line because the roughness profile is the difference between the actual profile and the mean line. Thus 2 1 α H R = exp − π 1 . α α
50%
∑ ( z − m ) s ∆x → Min m
2
l
k
kl
k
(2.56)
1
where skl is the Gaussian function given by
skl =
λc
π 2 (( k − 1) ∆x )2 1 exp − ln ( 2 ) ln ( 2 ) λ c2
(2.57)
where λc is the filter cut-off. As reported by Raja [25], the weighting function is calculated for every point on the profile and the objective function i.e., the sum, is minimized to compute the mean line point corresponding to it. 2.2.1.3.7 Multi Process, Stratified Surface Filtering In many cases very severe components of waviness do not occur, but there are some instances where there are more than one process present these are called multi-process geometries and they are notoriously difficult to deal with. One such class is called stratified surfaces typified by plateau honing in which a surface is fine honed or ground and the rough honed afterwards. This produces a surface in which the fine surface is mixed with wide deep scratches produced by the large honing stones. These scratches are intentional because they are used to collect debris and also to act as an oil reservoir. These surfaces are used extensively in the car industry to finish cylinder bores. A typical scratch is shown in the presence of roughness in Figure 2.38 and idealized below it in (a) and in (b) how a
32
Handbook of Surface and Nanometrology, Second Edition
L Rq d 2l (a)
0
d
(b)
e d’ 2l
2l
FIGURE 2.38 Distortion of the roughness by the response of the deep scratches to a standard filter. (After Whitehouse, D. J., Proc. Inst. Mech. Cngrs., 199B(4), 263–70, 1985.) ∞
l’ l
50
P (s) =
∫ p( x ) exp( – sx ) dx 0
l
d P (s) = − l
∫ x exp(−slx )dx 0
Percentage
40
+
30 e d
20
d’ d
=−
d l
2l
∫ (2l − x ) exp(−slx )dx l
d 2d d + exp ( − sl ) − 2 exp ( −2sl ) , (2.58) ls 2 ls 2 ls
which is the Laplace transform of a honing scratch! The Laplace transform of the standard filter is F(s)
10
F (s) =
0.05
0.10
0.20
Variation in scratch paramerers as a function of scratch width relative to cut-off length Conventional filter
Phase corrected filter
FIGURE 2.39 Scratch distortion by use of phase corrected filter. (After Whitehouse, D.J., Proc. Inst. Mech. Cngrs., 199B(4), 263–70, 1985.)
standard filter reacts to it. It can be seen that the overshoot would completely distort the roughness signal to the right of the scratch and would give the impression that the large honing stones would be producing huge amounts of pile up to the one side of the scratches which in practice does not happen. How the parameters of the scratch distortion can be reduced considerably by the use of a phase corrected filter is shown in Figure 2.39. The trick in evaluating these messy roughness profiles is to idealize the scratch and then deal with it as if it were an impulse into the filter and use Laplace transforms to evaluate the overshoot as if the whole problem is electrical rather than one of production engineering, thus using the symbols of Figure 2.38
s2 s + 1 γ
2
The output G(s) of any filter F(s) is G (s) = P (s) ⋅ F (s)
yielding, G ( s ) = −
−
d
+
2
exp ( −2ls )
s + 1 l γ d s+
2d exp ( −1.sl )
2
1 l γ
2
s + 1 l γ
(2.59)
which inverts to β 4H α − d 2 α − β exp − A α − β g (α ) = β 2 2
−α
2d ( exp ( − Aα )) + H ( α − β ).(α − β ) β
× exp ( − A ( α − β ))
(2.60)
33
Characterization
If d is made equal to unity, the output height will be relative to the original pulse depth. H is the Heaviside step function. The phase corrected standard filter gives the output g(α) g(α) = K exp(–j|α|) – 2KH (α – β) exp (–j|(α – β)|) + 2KH(α – 2β) exp (–j|(α – 2β)|) (2.61) This with Equation 2.60 give results of Figure 2.39. A is the distance along the profile as a ratio of the sampling length which usually takes the value of 3.64. 2.2.1.3.8â•… Robust Filters This refers to filtering techniques with have embedded in them a way of reducing the effect, on roughness assessment, of extra large peaks or valleys present in the primary profile which are either defects or the remnants of earlier coarser manufacturing processes. The classic example of this being plateau honing discussed above. The presence of completely different components making up the roughness means that steps have to be taken to enable some degree of separation between them. As already indicated linear characteristics in the transmission curve could go a long way to achieving this, however, an ISO procedure has been installed which is to be used with the Gaussian filter. Figure 2.40 shows this in 5 Steps. It should be noted that this technique was devised for removing the effect of deep valleys from the primary profile but a similar procedure should be used for large peaks. Be warned that the word “outlier” is€jargon for either and is found in some documents. Ideally, first establish a mean line by using a phase corrected filter with a long cut-off wavelength relative to the widths of the large peaks or valleys. This is not directly attempted because according to ISO 11562 the mean line is achieved by using a 0.8 mm cut-off with an evaluation length of 4 mm or, only in exceptional cases, a 2.5 mm cut-off with an evaluation length of 12.5 mm. See ISO 3274 1996. There is an understandable quandary here because it is obvious that the 0.8 filter cut-off will not be sufficiently long to reduce the effect of any big scratch marks but at the same time there may well not be sufficient evaluation length to allow a longer cut-off length and there may not even be any scratches so the hope is that by taking all the steps in this procedure it will help to minimize the effect of any scratches that are€present. The next step, having obtained the mean line (a), is to remove the deep valleys (b) and then, the next step is to€Â�re-use the 0.8 mm filter to give a new “unfiltered” profile to which the valleys are re-instated in step (c) which produces a much more realistic mean line (d), the last step, from which to assess the plateau roughness: it has been raised to a level where the mean line is now applicable to the fine scale roughness. This is not strictly speaking a robust filter but it is a start to thinking in robust terms. With the advent of digital methods any number of techniques are possible depending on the application. Different manufacturers employ their own methods of filtering often having facilities to ignore large valleys or peaks altogether—so-called non-linear robust filtering and the German car industry has introduced a “standard” VDA 2008 in which a particular type of robust Gaussian filter is used. Because this
µm 5 Mean line
2.5 0
Step 1
µm 5 2.5 µm 5
Step 3
2.5
Step 2
µm 5 2.5 Step 4 µm 5 2.5 0
1
0
2
Step 5
mm
FIGURE 2.40â•… Steps for multi-process surface texture assessment. Step 1: Unfiltered primary profile, established, Step 2: Valleys in primary profile suppressed, Step 3: Reference line for roughness measurement established, Step 4: Reference line inserted on original profile, and Step 5: Roughness profile established. (After Taylor-Hobson, Ultra Software. Leicester, UK, www.taylor-hobson. com. With permission.)
is a software standard it is an example of what is now referred to as a “softgauge.” An example of its use is shown in Figure 2.41 which is a Taylor-Hobson implementation [24] of the VDA method. One possibility is Equation 2.63, Figure 2.42 ∞
m(x) =
∫ h ( x − τ ) z ( x ) dτ,
(2.62)
-∞ ∞
m(x) =
∫ h ( x − τ )ρ ( x ) z ( x ) dτ,
(2.63)
-∞
where ρ(x) is a weighting factor which is specifically chosen to distinguish between what is to be expected from a normal signal and what is not see, for example, Raja et al. [25].
n
∑(z − m ) s 2
l
k
kl
δ il ∆x → Min mk .
(2.64)
l
Where Δil is a form of Kronecker delta used here as a vertical weighting function equivalent to the analog form of ρ(x)in Equation 2.63, in addition to the Gaussian, in Equation 2.57
34
Handbook of Surface and Nanometrology, Second Edition
Cylinder liner 2 - Gaussian.MOD
Z (µm) 4 2 0 –2 –4 –6 –8
1.0
1.4
1.8
2.2
2.6 X (mm)
3.0
3.4
3.8 Taylor-Hobson
FIGURE 2.41â•… Gaussian filter of plateau honing. (Courtesy of Taylor-Hobson.) Cylinder liner 2 - Robust Gaussian.MOD
Z (µm) 4 2 0 –2 –4 –6 –8 1.0
1.4
1.8
2.2
2.6 X (mm)
3.0
3.4
3.8 Taylor-Hobson
FIGURE 2.42â•… Implementation of VDA 2008 Robust Gaussian filter on the same surface and with the same cut-off as in Figure 2.41. (Courtesy of Taylor-Hobson.)
which can be used to implement the robustness. “i” is the iteration number and “r” is the difference between the current iteration of the mean line and the profile at that position. There are numerous forms of this such as the one by Raja, where the modulus allows for valleys as well as peaks, 2
2 r r hence δ i +1,l = 1 − il = 1 for il ≤ 1, = 0 otherwise, CB CB (2.65) where CB = 4.4 × median (zl – ml), which is the effective height range of the “normal” roughness. Obviously, the problem is that of deciding what is normal and also what to do with those values which fall outside the norm. In the case above they are omitted which although has little effect on the roughness value has implications for the surface derivatives, especially curvatures. For many examples of robust Gaussian filtering see the methods of Li et al. [26,27], which include those of Tukey, Huber, and Hampel as well as one of their own. There is, unfortunately, no space to go into further details here, suffice it to say that there is a lot of work going on in this area.
Robust filtering in which non-linear actions are part of the procedure represents a departure from the conventional filtering used in surface metrology but in fact historically nonlinear methods have been used albeit not by choice but as a consequence of the particular filtering method. In particular mechanical filtering falls into this category and will be considered next. So far the methods considered apart from robust digital filters have been confined to linear techniques in which the method of separating the roughness from the rest of the signal could be judged using Fourier analysis. This idea is fine for conventional wave filters and any technique that can be reduced to the basic convolution. However, there are alternative methods which depend on discrimination in domains other than spacing, such as in height, slope, and curvature but before embarking on these techniques a few comments and tables concerning ISO documents will be made. 2.2.1.4╅ Morphological Filtering In the methods considered above all the whole-profile trace has been used in the positioning of the reference line (Table€2.9). There are other methods, however, in which only selected parts
35
Characterization
Filter F = Filter
Type
Category
A = Areal (3D)
L = Linear M = Morphological R = Robust L = Linear M = Morphological R = Robust
P = Profile (2D)
Anvil of micrometer
Anvil of micrometer
FIGURE 2.43â•… Justification of envelope system.
of the profile like the extreme peaks or valleys contribute to the positioning of the reference, such reference lines highlighting the importance of the peaks and valleys. A simple straight line grazing the deepest valleys was originally proposed by Schmaltz whilst Nicolau decided on using the highest peaks. The roughness value being taken as the average or maximum profile distance from the line. Neither of these methods has been extensively adopted. Two different envelope methods have since been proposed, the first, the rolling circle envelope, by Professor von Weingraber and the other by Schaeffer and Professor Bielle. These will be considered in turn. 2.2.1.4.1╅ Rolling Circle Envelope (E System) In 1957, Von Weingraber [28,29] proposed a system in which a circle was imagined to be rolling over the crests of the profile graph. He advocated such a system because he believed that it mimicked very largely the vertical position on the surface that the anvil of a micrometer or similar gauge would take if the size of the component were being measured. See Figure€2.43 in particular he first considered circular workpieces. During its path the circle would obviously not follow a straight course; sometimes it would drop into valleys, sometimes it straddled the peaks. It all depended on the radius of the circle relative to the average separation of the peaks. The reference line was taken to be the locus of the lowest point on the circle (Figure 2.44). The advantage of this system was that, with a suitable radius, the waviness and roughness could be separated out to
Rolling circle
R
TABLE 2.9 Semantics of Filters ISO/TS 16610-1
Locus of bottom of rolling circle
Rt
Rp
Dropped envelope
FIGURE 2.44â•… Envelope system rolling circle envelope.
some extent, the radius acting as an equivalent of the sampling length in the mean line methods (M system). It represented an ambitious attempt to provide a basis for a large number of geometrical features. Where it failed was its difficulty in instrumentation. This method has an advantage, at least in this form, of being quite simple to construct graphically and it does not suffer from the choice of origin, as does the leastsquares method described earlier. Suggested radii for the assessment of roughness have ranged from 3.2 to 50€mm, the earliest being 25 mm. It seems obvious that, in order to get the same degree of versatility as the choice of sampling length allows, it is necessary to provide the same sort of choice for the radius. In a relatively recent paper Radhakrishnan [30], examining the effect of the radius size€ on the measured roughness, showed that the rate of change tended to be greatest for 3.2 mm and concluded that this value would be best for distinguishing between roughness and waviness. This philosophy is questionable because it implies that some of the roughness is being attenuated. Perhaps a better criterion is to choose a radius corresponding to the minimum rate of change, which was the criterion adopted in deciding on the meter cut-offs in the M system. Using this criterion has led to the conclusion that the original 25 mm radius would be a better choice for general use, compared with the 0.8 mm Â�cut-off in the M system. One of the big problems with this method, apart from the instrumental ones, is that the technique, although being an effective filter, has transmission characteristics which depend on amplitude. For different amplitudes of waveform the transmission characteristic changes. That the choice of a set of radii is not simple may be judged from the point that for a random surface the Rp value has an approximate relationship to R—the radius of the circle, given by evaluating the number N of independence lengths τindep of€ the surface likely to be in contact with the shape of the rolling member. The mode of the envelope height distribution can be shown [35] to be close to the Rp i.e.,
zmode ~ Rp
(2.66)
and the number N of independence lengths τindep is given by
z2 N −1 zmode exp mode ≈ 2 π
(2.67)
zmode ≈ N 2
(2.68)
36
Handbook of Surface and Nanometrology, Second Edition
and for the shape of the envelope of Radius R,
objects are one surface and one circle (or disc to use the ISO terminology) respectively and the geometric object produced is the envelope. Before this a few words on morphology. The mathematics of morphology will not be pursued here because as in Boolean algebra the rules are somewhat different from those in conventional mathematics. Also some strange words appear such as “idempotent” which is taken to mean a property of an operation in which the outcome of the operation more than once does not change the outcome. It may seem strange to have to use such abstract concepts in the engineering problem of mechanical filtering, but it should be remembered that similar concepts are well known in engineering albeit in a more relaxed framework for example in “spark out” in grinding or “shakedown” in tribology where the main outcome is decided very quickly and subsequent operations have relatively little effect. Perhaps these should be called “idempotent-like” engineering processes? Some of the operations used in morphology include dilation in which an operation expands one input set by another and erosion which shrinks one input set by another. Addition, subtraction and others such as an interesting operation called a fill transform in which a profile can be converted into an areal object and a surface into a 3D object. Judging from the examples of these operations given in the ISO document it is clear that the operation for generating an E system envelope is that of discrete dilation filtering. Although the method is outlined in ISO/ TS16610-41 and referred to the work of Srinivasan in 1998 [34] the technique was actually worked out for the first time by Whitehouse in 1965 as part of a surface finish program package written for Taylor Hobson and published in 1971 [35] although it was not named as a morpholgical operation at the time! So the interesting fact emerges that the E system construction is in fact the Minkowsi addition which is a morphological dilation i.e.,
R N2 ≈ τ indep
(2.69)
Rp ∝ lnR ,
(2.70)
from which
which will be shown in the chapter on instrumentation. In Equation 2.70 R is the ball radius. It has been suggested that any system which is primarily concerned with a reference based on peaks rather than the profile as a whole must be functionally more significant in rubbing or contact processes. Since then, Radhakrishnan [31] has been investigating the three-dimensional characteristics of the envelope system using a computer. What he has shown is that there are considerable divergences between results obtained from a circle on the profile graph and the three-dimensional results nominally obtained with a ball on a real surface. The E system was originally dropped because of instrumental and computational difficulties. However, it is now proving to be more useful in both function and process control. This resurgence has been a direct result of improvements in measurement techniques and data processing. However, the original concept—that of using the ball directly on the surface—has not been pursued. Now it is simply simulated in a computer once the original data has been obtained—by means of the conventional sharp stylus or optical probe! From what has been said it is clear that the E system had its roots in very practical engineering metrology i.e., the measurement of size using a micrometer and the representation of the anvils as viewed from the surface. It also allowed some functional characteristics to be simulated like the movement of ball bearings in a race, although it was probably the former aspect which triggered von Weingraber’s thoughts into using this as a mechanical filter to remove waviness as an alternative to using the electrical RC filters advocated in the UK and United States. His argument was that his method was basically mechanical in nature and therefore had a better pedigree. The rejoinder from the UK was that although it was an interesting and attractive contender it had filter characteristics which were non-linear and very difficult to instrument. It is ironic therefore that this simple mechanical idea can be approached from a sophisticated mathematical direction using the theory of morphology, now used extensively in image processing. This was based on the works of the famous mathematician Minkowski, a contemporary of Einstein, who was also known for the application of his ideas in cosmology and on more recent work by Matheron [32] and Serra [33]. Some aspects of the application of Minkowski mathematics to metrology have been considered in ISO/TS 16610-40,41 and 49. This is possible in the E system because morphology is concerned with the operation of two geometric objects together to produce another geometric object. In this case the two
E system = D(A,B),
(2.71)
where A is the surface profile and B is the rolling circle (disc) and D means the operation of dilation. Figure 2.45 shows two envelopes produced by dilation of a small circle Profile
Small circle
Large circle
FIGURE 2.45 Envelopes and discrete dilated filtering.
37
Characterization
Structural element B
Dilated filter
Closed filter
Profile A
Closed filter profile (valley discrimination)
FIGURE 2.46 Closed filter profile and valley discrimination.
and lower a large circle. One criticism of Minkowski mathematics is that it is not altogether convincing for engineers because of some of its properties, for example, if the data i.e., the profile ends then strictly the dilation goes to minus infinity! However, this is not fair because the rolling circle drops off the data at the end of the profile and would go to minus infinity if this were allowed, so common sense, the prerogative of the engineer, should be exercised. In a similar way in erosion the circle—the structural element, should go to plus infinity. Figure 2.46 shows the profile subjected to a dilation by the structural element i.e., the disc (circle). This is the traditional E system construction as well as being a Minkowski addition. If then the dilated envelope is eroded, the Minkowsi subtraction, it positions itself back to touch the relevant peaks on the profile where it can be used as a reference line from which to measure the roughness. These two operations in the order stated produce what is called a “closed filter.”
C(A,B) = E(D(A,B),B′ ).
(2.72)
This reference line acts as a mechanical filter because it “bottoms” into any valley which has a spacing larger than the size of the structural element. This size is approximately equivalent to the sampling length. An opposite construction gives the “open” filter,
O(A,B) = D(E(A,B′), Β)
(2.73)
D is dilation, E is erosion, C is closed, and O is open in Equations 2.73 and 2.74. The designation B strictly refers to the lower part of the structural element geometry: that which is likely to touch the peaks of the profile in dilation and B′ refers to the upper part of the structural element: that which is likely to touch the valleys in the erosion operation. In the case of
the E system they are the same because the structural element is a circle and is therefore symmetrical about a line through its center. Because of the method of construction the closed filter deals with the roughness as a succession of valleys and the open filter as a succession of peaks as seen in Figures 2.46 and 2.47. 2.2.1.4.2 Scale–Space Representation A traditional way to investigate a signal is to pass it through a bank of filters to break it down into frequency components. This exercise is easy electrically but not so obvious mechanically. In the case of the morphology filter the bank of filters is replaced by having a series of circles or whatever shape has been chosen as the “‘structural element.” The various sizes of the structural element, say, the disk, in effect determines what is bridged by the reference line in its passage across it: one size picks out one feature whilst another size may pick out some feature which is completely different. In the same way that a filter bank usually has a fixed ratio between the filter cut-off values so to it is usual to have the sizes of successive circles as a constant ratio, invariably taken as 2 which fits in with octave shifts in frequency bands. The concept of using a succession of values of the structural element usually having a constant ratio is called a “scale–space” representation. Figure 2.48 illustrates how by comparing the loci of an erosion filter of one radius with that having twice the radius information is obtained which can be regarded as typical of that octave of scale of size between them. The comparison is made between the shape of the two loci by subtracting them after removing the fixed radius value as seen in the lower graph of the figure. The presentation of the comparison has to be viewed with some care: Sometimes the result is shown directly as seen in Figure 2.48 which is the preferred way, or the DC can be removed as appears to be the case in Figures 2.49 and 2.50.
38
Handbook of Surface and Nanometrology, Second Edition
Structural element B Profile
Open filter
Open filter profile (peak discrimination)
Erosion filter
FIGURE 2.47 Open filter representation. Structural element B C
Profile
Erosion filter C
Erosion filter B Difference between octave Erosion filters C and B
FIGURE 2.48 Difference between structural filters octave band separation.
This approach can be extended to cover a large number of octaves as seen in Figures 2.49 and 2.50 which are two practical examples from ISO/TS 16610-49. In these the original profile is shown at the top of the picture with a mean line superimposed on it and underneath this is a sequence of eight octave steps in structured element size in much the same way that wavelet results are displayed except that wavelength not size is used. Notice how prominent the dip in the locus is at the long radius value of the scale illustrating the ability to pick out defective milling marks. Remember, however, that the actual value of the dip revealed by this “pseudomechanical” method is a function of both the amplitude as
well as the wavelength of the marks producing the depression: it is non-linear, so that the technique is more of an indicator than an assessment. Figure 2.49 shows that the shorter wavelengths are preserved at the expense of the microfracture marks. 2.2.1.4.3 Motif Characterization R and W A system of measurement R & W, has been advocated in some countries. It is similar in some respects to the morphology approach because it involves a peak and valley envelope line. As with the E system it was based on a very practical requirement without having a formal framework in its original form.
39
Characterization
Y 14
12 10 8
5 2 1 0.5 0.2 A 0.1 0.05 0.02 0.01
6 4 2 0 –2
0
0.2 0.4 0.6 Key X Distance, mm Y Hight, µm A Scale, mm
0.8
1
1.2
1.4
1.6
1.8
2 X
FIGURE 2.49â•… Scale–space representation of milled surface with circular structural element. (Permission to reproduce extracts from ISO/TS 16610-49 British Extracts is granted by British Standard Institute under License No. 2010ET0013. http://shop.bsigroup.com) Y 12 10 8
5 2 1 0.5 0.2 0.1 0.05 0.02 0.01
6 4 2 0 –5
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
Certain restrictions have to be placed on the drawing of these tangents. If the depression of the envelope between any two contacts A and B shown in Figure 2.51a is only 10% of the roughness value, then the tangent has to be redrawn ignoring the secondary tangent contact B and proceeding to the next contact C. How this technique is instrumented is described later in the chapter on instrumentation. 2.2.1.4.4â•… Motif Methods The motif method is also an envelope technique. It was suggested in France [36] in the early 1970s. The “motif” method in principle is rather simple. The unfiltered profile is divided into useful geometrical characteristics in accordance with an empirically found algorithm which should be determined by the combined experience of people dealing with profile analysis. In one form the motif consists of€just two profile peaks with a valley in between them. The motif is characterized by the two heights H1 and H2. The characteristic depth T of the motif has a special significance in the evaluation: it is the smaller of H1 and H2. The mean depth is (H1â•›+â•›H2)/2 and AR1 is the distance between the peaks. Application of the motif method involves checking whether two adjacent motifs can be treated separately or whether one of the motifs can be regarded as insignificant and absorbed into the other one to make one large motif. Two motifs cannot be merged if any of the four conditions apply.
A
2 X
Key X Distance, mm Y Hight, µm A Scale, mm
FIGURE 2.50â•… Scale–space of ceramic surface circular structural element. (Permission to reproduce extracts from ISO/TS 16610-49 British Extracts is granted by British Standard Institute under License No. 2010ET0013. http://shop.bsigroup.com)
The method was based on a subjective assessment of the profile. The graph is taken with a horizontal magnification of about × 20 and then a skilled operator traces two undulating lines more or less following the peaks and valleys but ignoring minor features separated by less than about 0.5 mm. The roughness value R is then taken to be the average of 10 measurements of height between the two envelope lines. Waviness can also be measured in this system by a system of tangents drawn between the uppermost points on the peak envelope.
1. Envelope condition (Figure 2.51b ii). Two adjacent motifs cannot be combined if their common middle peak is higher than the two outer peaks. 2. Width condition (Figure 2.51b iii). Adjacent motifs can only be combined if the result is less than or equal to 500 μm. This is a very weak condition indicating that motifs up to 500 μm are to be included as roughness. It corresponds in effect to a cut-off. The width limit for evaluating waviness is 2500 μm. These arbitrary rules have been proposed with the car industry in mind. 3. The magnification condition (Figure 2.51b iv). Adjacent motifs may not be joined if the characteristic depth of each of the adjacent depths T3 of the result is less than the largest characteristic depth of each of the adjacent motifs. This condition is most important. It means that in each case an unequivocal evaluation can be reached independent of the tracing direction. 4. The relationship condition (Figure 2.51b v). Adjacent motifs may be considered if at least one has a characteristic depth less than 60% of the local reference depth TR . Thus, adjacent motifs of approximately the same size cannot be combined to form one single overall motif.
The reference depth TR may appear in two forms. It may be the largest depth found in any one suitable profile section approximately 500 μm wide; it is then called the local depth reference. Alternatively it may be the characteristic depth T3 which a combined motif would have.
40
Handbook of Surface and Nanometrology, Second Edition
(a)
B
W
C R
P1c
(b) (i)
A
c P1 H1
H2
AR1 Creux (ii) P1
P2 P 3
P1
P1 P2
P2 > P1,P2
P2
P3
P3
P2 < P1
P2 < P1,P2
(iii)
AR1
AR1
500 µm (iv)
500 µm
AR1 > 500 µm
T1
T3 < T1
AR1 > 500 µm
T2 T3
T1 T2 T3 T3 = T2,T3>T1
T2 T1
T3 > T1,T2
T3
(v)
6 TR
T1
T2 T1,T2 > 0.6 TR
0.6TR T1
T3
T2
T2, < 0.6 TR
0.6TR T1
T2
T1,T2 < 0.6 TR
FIGURE 2.51â•… (a) Motif method—R and W, (b) The motif and the four conditions for motif combination: (i) definition of motif; (ii) envelope condition; (iii) width condition; (iv) magnification condition; (v) relationship condition. (After Fahl, C., Verfasser, 28(6), 1982.)
The basic principle to follow when deciding on an evaluation is to find the largest motif in the measured profile which fulfils all conditions, that is the profile should be described with the least number of the largest possible motifs. 2.2.1.4.5â•… Motif Procedure First, the local reference depth over the relevant sections in the profile is found (according to Fahl [37], Figure 2.51b). Then within each individual section every single motif is checked against its neighbor using the four conditions above and whenever necessary combined with a new motif. Every new motif must be compared with its neighbor until no further combination of two motifs is possible within that section. This is carried out for each section of the profile. When completed, all motifs that lie outside the limits of the
section must be checked with each other until no further mergers are possible. In theory this is the end result. In practice, however, there are other considerations. Examples of this include the presence of single isolated peaks or valleys. These have to be smoothed to a “reasonable” level. After this the “corrected” profile results. Then, Rm the average motif depth, A R the average width and p(Rm), p(A R) the distributions of Rm and A R are found. After these calculations a near profile comprising the peaks just found is made. The whole procedure is repeated, except that, instead of 500 µm, 2500 µm is used. This corresponds to the envelope above the corrected profile. This time Wm , Aw and p(Wm), p(Aw) are found and taken as the waviness parameters. The whole procedure can be repeated to give the form profile. This represents
41
Characterization
the complete breakdown of the profile into roughness, waviness, and form. 2.2.1.5 Intrinsic Filtering The representation of the original profile in blocks is reminiscent of the methods of filtering using the sampling length described earlier. In this case, however, the blocks are determined from the surface itself and could therefore better be described as “intrinsic filtering.” Any local effects on the surface which are not characteristic will automatically be taken into account. The sampling “matches” itself to the local properties of the surface. In this motif method Rm is approximately Ry or Rz qualified by a varied sampling length. AR is the average width between significant peaks. This corresponds to Sm, the average distance between zero crossings of the profile with the mean line. The advantage of the motif method is that it “reacts” to the surface uniquely according to a set of rules. The disadvantage is that the rules are arbitrary. They could, in principle, be modified to suit any given function. Another disadvantage is that the motifs are peak oriented; quite major peaks near to a valley are ignored, yet small peaks near to a major peak are not. A different set of rules would be needed to make the algorithm symmetrical. The arbitrary selection of 500 μm and 2500 μm is a disadvantage but no more than the 0.8 mm cut-off selected for the filters. It seems that the motif method is another way of looking at profiles, perhaps complementing the filtering methods or perhaps best suited for dealing with multiprocess surfaces where no standard characteristics occur. Another possible use is in plotting the distribution of given sizes of motifs. This is almost the metrology equivalent of a Pareto curve. Using this curve motif size against frequency of occurrence can be plotted for roughness and waviness and can represent some interesting information. Exactly how it can be used is not obvious but it is a different type of breakdown which does not rely on a reference line but on adequate definitions of peaks. 2.2.1.6 Summary In the foregoing the development of characterization methods for a profile graph has been described. These have been somewhat piecemeal in the sense that height and spacing parameters have been described. At the same time considerations of reference lines and sampling lengths or equivalent cut-off lengths have been given. This is all part of the attempt to classify the surface into its significant components and as such is pertinent to the chapter on the characterization of surfaces. The classification has been involved with many factors including dimensional metrology, functional, and manufacturing considerations as well as height and spacing parameters. A rather more coherent, yet not necessarily more relevant, classification is based upon random process analysis of the surface. It may appear that random process analysis occurs just about everywhere in classification in different guises. This observation is true. Such is the potential of random process analysis that inklings of it have occurred over
many years and for different purposes. This chapter reflects this situation. It would not be correct to isolate the subject of random process analysis from its various functional usages, for they add to its credibility. Hence vestiges appear in many places in this and other chapters. Comment on Specialist Terms in ISO Technical Specifications It should be made clear that many of the terms adopted by the various standards committees and research institutes are not necessarily what a production or mechanical engineer might expect. This does not mean to say that they are wrong but it does mean that rather than clarifying the situation it could confuse it. The essential word is “comfortable.” Unless an operator or investigator is familiar with the term and relate it to everyday use i.e., is comfortable with it it will not be accepted in the long term. An example is the term “integral feature” defined in ISO/TS 16610-1. This is “a surface or line on a surface.” Another is “primary mathematical model” which is “a set of nested mathematical representations of a surface portion wherein each representation in the set can be described by a finite number of parameters,” where a surface portion is a portion of a “partitioned integral surface.” The problem is that although it is necessary to set up a rigorous framework such as set out in the ISO/TS 16610 documents and to define all eventualities, which often end up looking as complicated those two mentioned above, even the most straightforward of techniques such as the Fourier analysis of a roundness graph has to take on all the ramifications set out in the documents and as a result is largely unreadable! The documents are written in formal mathematical terms which do not sit comfortably with engineering! This is a personal view of the author of this handbook who is no stranger to mathematics and who is concerned with communicating mathematical techniques effectively to engineers who have to define the problem in the first place as well as implementing the solution without being buried in “general mathematical jargon.” Some effort is being made to solve this problem using what is called “category” theory which is supposed to help in the organization of complex organizational problems. See the work of Jiang [79] in Chapter 5.
2.2.2 S tatistical Parameters and Random Process Analysis of Surface Roughness 2.2.2.1 General The theory of random process analysis is now well established in the field of metrology research and partly in the standards but has yet to make a significant impact in industry. This difficulty in penetration has been partly due to the mathematical basis of the parameters which many practical engineers find difficult to follow and consequently to interpret. They tend to feel uncomfortable with such advances and as a result tend to be reluctant to use them. In what follows the basic statistical ideas will be given but at the same time some of the background to their use and how and why they were applied in the first place in order to give engineers, in particular, a feel for the subject rather than just give the bald formulae.
42
Handbook of Surface and Nanometrology, Second Edition
Many investigators have tried to formulate statistical rules with which to describe the geometric properties of surfaces. Basically the problem is that surfaces can be random, deterministic or usually a complex mixture of both. High-order probability density functions are needed to specify the general surface statistics completely at one end of the scale of complexity, yet only a simple formula involving a few parameters is needed at the other end to determine the complete profile. Somewhere in between these extremes lies the practical characterization of surfaces. Such a compromise may exist by considering the autocorrelation function of the surface and the APDF, respectively. Taken together they provide a reasonable basis for the topographic analysis of surfaces, especially if only a profile is being considered, but they are by no means the only functions that can be and have been used as will be seen later in this section. In particular there are problems when the statistics change across the surface, the so called “non-stationary” condition and the very difficult cases where scratches or other defects are present on the surface which are not typical and therefore are difficult to model, to predict and even to find!
and the probability of a measurement lying between z1 and z2 is
2.2.2.2â•…Amplitude Probability Density Function 2.2.2.2.1â•… Definition It is possible for any continuous waveform, whether it is a profile signal or not, to be drawn as a graph as shown in Figure 2.52. The two axes of the graph are height z and p(z), the probability density that any measurement has the value of z. Some of the properties of the APDF are that it has unit area, it extends over the range zmax–zmin and it may take on a variety of shapes depending on the profile. In metrology it is a useful convention to plot the z axis to the APDF in the same direction as the z direction of the profile. This arrangement makes visualization easier. It is perpendicular to the method of display usually used in statistical textbooks. Also used to describe amplitude information is the cumulative distribution function (CDF) which is perhaps more useful. This represents at any level z the probability that a measurement of the waveform will be less than z. To find the probability of a measurement of the surface lying between levels z 1 and z 2, it is necessary to integrate the APDF between these two values. Thus, if p(z) is the APDF, then the CDF is given by P(z') where z′
P ( z ′) =
∫ p(z) dz
(2.74)
–∞
p(z) z zmin
z zmax
Profile
FIGURE 2.52â•… Statistical breakdown of profile.
p(z)
∫
z1
p( z )dz.
z2
Similarly p(z) = limitâ•›Δz→0 (probability of measurement between z and z + Δz) (Figure 2.52). 2.2.2.2.2â•… Material Ratio Related to the CDF is the “Abbott–Firestone” curve which has been mentioned earlier [8]. (This is 1–P(z), in words, the probability that a measurement is higher than a given level z). In mechanical terms it gives the percentage of material to air of the surface profile at any level. For this reason it is sometimes referred to as the “bearing ratio” or “material ratio” which is the current terminology. It has also been called the “bearing area,” curve the reason being that for a typical profile, i.e., the surface does not change its character over the area it is the same value as the bearing ratio. The problem is that all these names, for what is basically the same thing, completely confuses the issue and the acceptance of what is an eminently practical concept. These curves only give height information. That is, they only give the frequency of occurrence with which measurements lie between certain limits. They do not give any information about the spacing between such measurements or the order in which they occur. Ways of disseminating the height information of a profile based upon these techniques have been attempted for a number of years. The earliest seems to have been by Pesante [9], who advocated the use of APDF curves to control the different manufacturing processes. Ehrenreich [10] and Reason [38] have proposed different features of the material ratio curve. Ehrenreich suggested measuring the slope between the air/metal ratios of 1/3 and 1/2. This slope value can be determined also from the APDF because it is a form for the differential of the bearing ratio curve. Reason used a model of the surface comprising what he called a “consolidated” profile made up of a sequence of mirror-imaged bearing curves. He also incorporated the scale of size of the graph in both directions. 2.2.2.2.3â•… Moments In formal terms the APDF can be regarded as a tool for specifying the characteristics of unknown waveform statistics. It is not necessary to specify it in the case of deterministic waveforms such as a square wave, sawtooth, etc., simply because the curve can be worked out from a knowledge of the formula for the waveform. This can easily be verified with reference to a sine wave. Thus z = A sin x where the angle x takes values from 0€to 2π in other words x is uniformly distributed within the interval 0→2π. The probability function for x treats it as a random function because it does not matter (from the point of view of height distribution) in which order the x values are taken.
43
Characterization
The probability density function is 1 0 < x ≤ 2 π. 2π = 0 otherwise
p( x ) =
(2.75)
If p(x) and z = g(x) are known—a deterministic function for all z, z'0 = g(x0)—the probability that z lies between z0 and z0 + dz must equal the probability that x lies in the range x0€to x0 dx. Hence p( x0 )dx = p(z0 )dz or
p(z ) =
p( x ) . dz /dx
(2.76)
If each value of z has n values of x then x = g−1(z) is multivalued and p(z) = np(x)/(dz/dx). This is the determining relationship for the APDF in terms of the deterministic relationship between z and x. For a sine wave dz /dx = A cos x =
A2 − z 2
so x = cos−l(z/A) which is double valued and p( z ) =
2 p( x ) 1 = A cos x π A2 − z 2
for − A < z < A. (2.77)
The corresponding distribution function is P(z'): z′
P ( z ′) =
1 π
∫ p(z) dz = π 2 + sin
−1
−A
z . A
Because many surface waveforms are neither truly deterministic nor random, the material ratio curve does have some use in describing the surface; the shape can give some idea of the nature of the surface relative to the purely random wave given by the Gaussian or normal distribution p(z) (Figure 2.53) 1 exp ( − z 2 / 2σ 2 ) 2π
p( z ) =
(2.78)
(b)
(a)
z p(z)
p(z)
FIGURE 2.53â•… (a) Gaussian amplitude distribution and (b) sinusoidal amplitude distribution.
∞
z k p( z )dz
(2.79)
zp( z )dz
(2.80)
–∞
and if the mean value of z is
∫
z=
∞
–∞
then the central moments are given by µk: µk =
∫
∞
( z − z ) p ( z ) dz. k
−∞
(2.81)
It is these central moments that give useful parameters about the shape. Because the mean level z is arbitrary, it represents the mean distance of the surface from the reference level in€the instrument measuring the surface. As such it therefore contains no useful information. The information is contained in the relative values of the central moments and in particular the skew Sk and kurtosis Sku. The skew is defined as Sk =
1 σ3
∫
∞
( z − z ) p(z )dz
(2.82)
( z − z ) p(z )dz − 3.
(2.83)
3
−∞
and the kurtosis as Sku =
z 1 π MR( z ) = − sin –1 . A π2
∫
mk =
The material ratio curve is unity minus the distribution �function, so for a sine wave it is
where σ is the RMS value of the profile Rq. The reason for this will be given later. Rather than specify the whole shape of the APDF it is often more convenient to break it down using the moments of the curve. Thus if the kth moment of the curve is mk
1 σ3
∫
∞
4
−∞
where z is the mean height of z. Both are normalized with respect to the RMS value of the profile waveform σ (where σ = √μ2 is the standard deviation of the surface and is equivalent to Rq). Essentially the skew shows the degree of symmetry of the profile while the kurtosis shows the degree of pointedness or bluntness of the waveform (Figure 2.54). How these can be used will be seen in the subsection on characterization. Peklenik got Al-Salihi [39] to investigate the use of the moments in the form of a Gram–Charlier series. However, it is only recently that they have started to be used seriously. The skew in particular has been used as a control parameter to judge the value of the conventional Ra, Rt values, etc. This control property is based upon experience of the typical shapes of profiles, the manufacturing Skew
Kurtosis –ve
+ve
+ve
–ve
FIGURE 2.54â•… Examples of skew and kurtosis in surfaces.
44
Handbook of Surface and Nanometrology, Second Edition
processes, and the functional effects of such waveforms. Take, for example, the profiles shown in Figure 2.54. These are taken from surfaces produced by different methods. The formulae expressed above are not the only ones for the central moments. They can all be expressed in terms of baseline moments. Remember also they can be defined along the x axis. For example, letting
effect of repeated convolutions will produce a Gaussian output irrespective of the shapes of the signals being convoluted. In practice, any more than four or five convolutions will give this effect. This explains why many finished processes, such as grinding, have an APDF which is Gaussian. Because of this fortuitous phenomenon much analytical work has been made possible on models of surfaces for use in contact theory and optics as will be seen in Chapter 7. Incidentally if the randomness is imposed transversally, i.e., in glass polishing the action will produce a height geometry which is spherical. This is because the lateral action is ∝ exp(–(x2 + y2)) from which z = √(x2 + y2) which produces the circular symmetry about the z axis which is why spherical lenses were always the starting point in early optical components: they can be produced from random movements, or more precisely, they will always be produced by random movements. Ball bearings are still made this way!
z=
∫
∞
zp( z )dz v2 =
−∞
∫
∞
z 2 p( z )dz v3 =
−∞
∫
∞
z 3 p( z )dz (2.84)
−∞
where –z , v2, and v3 are, respectively, the first, second, and third moments about the arbitrary baseline from which the z values are measured, the skew Sk is
Sk =
1 (v3 − 3zv2 + 2 z 3 ) σ3
(2.85)
where σ 2 = v 2 − z 2 . Judging from these it seems reasonable to propose that, if the skew value is bigger in value than ±2, then a straightforward measure of Ra etc., will be questionable; it will not be quantifying the feature of the profile considered to be functionally most important. This value of 2 is rather fortuitous because it can be shown that the skew of a random wave truncated at the mean level gives a skew of 2.1 which is very close to 2. For control purposes, therefore, a value of skew greater than 2 would indicate that care must be exercised when taking simple measurements. 2.2.2.2.4 Other Properties of the APDF If, as is usually the case, a workpiece is made using more than one process the profile often shows evidence of it. The profile may comprise more than one identifiable characteristic, each one given by one or other of the processes. This produces what is called a stratified surface. (See ISO 13565-2.) If the processes are additive in nature so that z at any x can be written z = z1 + z2, then the APDF p(z) is given by the convolution integral
p( z ) =
∫
∞
−∞
p1 ( z1 ) p2 (z − z1 )dz1
(2.86)
where p1(z) and p 2(z) are the individual APDFs for z1 and z 2. In many cases in manufacturing this additive effect is present: one set of geometries is superimposed on another and in other cases it is not. Consequently the convolution does not hold. In the former case deconvolution enables the variables z1 and z 2 to be identified statistically by their APDF providing one of the two is known. The material ratio curve is useful for separating the different process characteristics in terms of their height whereas the use of linear transmission filters could be used to isolate the spatial characteristics. If many interdependent variables are responsible for producing the final profile the resultant APDF p(z) will usually have a form that is Gaussian in shape. This is because of the central limit theorem which can be stated as follows: The resultant
2.2.2.3 Random Process Analysis Applied to Surfaces A major breakthrough in recent years in the characterization of surfaces has been the use of some of the mathematical tools used in communication theory. Those used in random process analysis have been most prominent. In particular, the autocorrelation function has been especially important. First used in 1946 in surface roughness [40], the idea of correlation itself is well known in statistics and stems from the need to predict the influence that one set of numbers has on another set. One set comes perhaps from the input to an experiment and the other from the output. Dealing with one profile signal alone is hardly what is meant by a random process. What is usually implied is that many sets of information are being considered and the average relationships determined. In the case of surface metrology the many sets of data correspond to the whole surface including texture. One profile represents merely a very small subset of the total data. However, such is the nature of correlation functions that by investigating the statistical properties of one or at most a few profiles, valid information is obtained about the whole surface. This is not necessarily the case when using the deterministic parameters. Many of them give information which is dominated by the idiosyncrasies of the individual profile and hence is unsatisfactory. Because of this property the use of correlation methods is on the increase; the correlation function is bringing more predictability to the measurement of the random features of surfaces. Why this is so will be seen presently. The property of relating to the whole surface rather than individual profiles makes the autocorrelation function (and its equivalent, the power spectral density) very attractive for use as a basis for characterization. In fact random process analysis, which comprises the amplitude distribution and the autocorrelation function and power spectrum, has been the source of much research into characterization and more has developd from It as will be seen later in this chapter. The idea, basically, is to estimate as many parameters of significance in the function of the surface as is possible from a few random process parameters, thereby
45
Characterization
making savings on the amount of measurement required as well as increasing the reliability of measurement. Consider now characterization of surfaces using random process analysis. This has followed two distinct paths: one uses the power spectral density and its moments, and the other uses discrete values taken from the autocorrelation function. Both methods were initially devised to help to predict the many functional requirements to which surfaces are subjected. The former approach originated from the work of Rice [40] in communication theory. This was expanded to cover other areas by Longuet-Higgins [41], in particular the sea. Peklenik [42] was the first to apply the results of Rice to surface metrology and Nayak [43] then used his results to relate the moments directly to parameters of contact such as the mean peak height and the curvature of peaks. Nayak also coined the terms “summit” for a three-dimensional (or areal) maximum as opposed to a profile “peak.” The other approach, the discrete technique, was originated by Whitehouse [44]. In its original form the autocorrelation function was constrained to be exponential. The characterization then became simply the RMS σ value of the surface and the correlation length—that length over which the autocorrelation length falls to a small value τ* Later this discrete characterization was extended to an arbitary autocorrelation function and three points A(0), A(h), and A(2h) for a profile where h was an arbitrary distance. Finally, four or more points were used for the areal characterization of the surface. From these the same functional parameters were derived. The basic difference between these two approaches is that the Nayak model is worked from a continuous signal and hence can be regarded as exact. On the other hand the Whitehouse model, because it is discrete, can only be approximate yet it does mimic exactly what is measured. It is nevertheless a form of surface characterization in its own right. The Whitehouse model appears here in its role as a method of characterizing the surface. It also appears in Chapter 3 in its role as a means of explaining the range of values which measured surface parameters can take, it being assumed that all calculations are nowadays carried out digitally. It may seem confusing to have two different methods of evaluating the same thing (namely, the functional parameters). Readers would be advised to consult, also, works of Greenwood who input much of the Â�information on which the functionally important parameters were based. 2.2.2.3.1â•…General Properties of the Autocorrelation Relevant€to€Surfaces Before dealing with this some properties of the random process signals will be demonstrated. The definition of the autocorrelation function is as follows. If z1 and z2 are two measurements taken on the surface a distance τ apart then the ACF is given by A.(τ) where A.(τ) = E[z1,€ z2], where E[] denotes the expected value of
the product of these measurements taken over the entire surface:
E[ z1z2 ] =
∞
∫∫
∞
z1z2 p( z1z2 ) dz1 dz2
−∞ −∞
(2.87)
Providing that two conditions are complied with, the formula E[z1,z2] can be modified to a more useful form, that is, one incorporating a profile. The conditions to be satisfied are, first, that the random nature of the surface is uniform in distribution and, second, that the ergodic theorem holds. The first of these conditions is self-explanatory but the second is not. It must suffice here to comment that the real surfaces are€close enough to uniformity and ergodicity to justify the use of the ACF. Some examples of processes not satisfying these conditions can be found in communications textbooks. Under these circumstances the formula may be rewritten as
A(τ) = E[ z1 , z 2 ] = lim
1 L
∫
L /2
− L /2
z ( x ) z ( x + τ)dx (2.88)
For τ = 0, E[z1,z 2] = A(0) = σ2, the variance of the signal, or R2q in surface terminology. Because E[z1,z2] = E[z2,z1] it follows that the function has even symmetry about τ = 0 (Figure 2.55). Basically, ergodicity means that averages of many surface profiles taken at the same time (or x value) are the same as averages taken of one profile over all time. See Figure 2.56 which shows that correlation evaluated for a given lag over many parallel profiles, called the ensemble correlation, can be closely approximated by the measurement of the correlation using the same lag value taken along the length of just one profile, which makes the measurement much simpler but it should be remembered that this is not the formal derivation. However either way means that all phase is lost in the signal. In a system the phase angle ϕ is given by
X (function) φ = tan −1 R (function)
(2.89)
but in Equation 2.88 the function is real because the ACF is even. Hence X(function) = 0 and thus the phase is zero. It is because of this that the ACF has the useful property of being more reliable than deterministic parameters. It is the phase effects and particularly the random phase effects which influence the individual characteristics of a profile such as the highest peak etc. The random amplitudes contain the essential information, the energy information. Consequently, 1.0 (a)
(b) τ
FIGURE 2.55â•… (a) Typical profile and (b) autocorrelation function.
46
Handbook of Surface and Nanometrology, Second Edition
Ensemble correlation Lag z Lag
Parallel evaluation z of correlation
x
z z
x
z
x x
z x
x
Serial evaluation of correlation Lag Temporal correlation Lag
FIGURE 2.56 Ergodic principle—ensemble average vs. temporal average.
1.0
Unit machining event
1.0
Profile
FIGURE 2.57 Manufacture—unit event from correlation.
removing, not measuring, the delinquent random element (the phase) improves the stability. One property of the autocorrelation function not often realized is that it can reveal the “average machining unit event.” To see how this happens consider shotblasting. The unit event here is the crater left on the surface after the bead has impinged on it. Such a crater is shown in Figure 2.57. Alongside it is its ACF. The profile in the figure is a typical profile of a shotblast surface together with its ACF. Notice how little has been changed. The reason for this is that it is by the random positioning in space of the unit event that the profile is built up. This means that the beads hitting the surface are uniformly distributed in space. Heuristically it
can be argued that the only difference between them (apart from some degree of geometric interaction) is spatial. This constitutes only phase information and, because the ACF is not responsive to phase, this is ignored. Hence the autocorrelation function itself is merely showing the ACF of the average unit event. The degree to which this is true can be seen from the figure. The only proviso is that the statistics of the manufacturing process have to be Poissonian, that is uniformly distributed in space, which is true for many finishing processes. More of this will appear in Chapter 6. The first use of correlation in surface metrology was suggested by Wormersley and Hopkins in 1946 [45], who advocated the use of methods previously used for examining turbulent air flow for looking at surfaces. (They were associates of R. E. Reason at Taylor Hobson. Hopkins joined with Reason in producing the first definitive book on surface metrology in 1944 [2].) Linnik and Khusu [46] and Nakamura [47] looked at correlation later. However, it was Peklenik [42] who proposed the use of the ACF in terms of a typology for surfaces and, since this time, it has become acceptable to specify surfaces in terms of the statistical properties of surface height rather than the distribution of peaks and valleys, at least for certain application. What are the most useful parameters of the ACF? Parameters taken from the single-profile graph will be examined first. This in itself will consist of two sets of measurements, one direct from the ACF and the other indirect
47
Characterization
via power spectra etc. Then the areal assessment of surfaces using statistical methods will be described.
This has a correlation length which is obtained from
2.2.2.3.2â•… Direct Parameters Two parameters emerge directly from the Â�signal-discriminating property of the ACF. First is the measure of how quickly the random element decays and second is the wavelength of the periodicity of the more deterministic component if any. Also, there is the possibility of classifying the type of process by examining the shape of the function. These possibilities have been explored by Peklenik [42] and others. Another function, the structure function S(τ) = E(z(x)–z(x + τ))2 = 2σ2(1–A(τ)) is also used [35]. It does not need a reference line. The parameters themselves relate to the scale of size of the abscissa of the correlation function. The correlation length, that is the length over which the correlation function drops to a small fraction of its height at the origin, has been defined as that length of surface over which the ACF drops to between 10 and 50% of its original value (see Figure 2.58). That this value appears to be somewhat arbitrary is merely a reflection of the fact that the definition of the value of correlation required for independence depends largely on the proposed function of the workpiece. One definition that has been used is
1 correlation distance = A(0)
∞
∫ A(τ) dτ
(2.90)
0
which, for A(τ) = exp(–τ/τ*) gives the correlation length to be τ* which corresponds to a correlation value of 1/e, that is 37%. The length over which the correlation drops to 10% of its value at the origin has been referred to as the independence distance but this value of 10% is arbitrary. Although this definition is easy to carry out for a simple exponential function it is not so easy for more complex functions. For example, a typical second-order correlation function is cos ατ A(τ) = 1 + γ 2τ2 1.0
A(τ) 1/e
τ
0 50%
10%
Correlation length
FIGURE 2.58â•… Autocorrelation function.
1 = A(0)
∞
cos ατ
∫ 1+ γ τ 0
2 2
dτ
(2.91)
which results in an expression
1 1 α cos h tan –1 sin hα / γ γ γ
(2.92)
This is not a simple expression. It could also be argued that the real criterion for independence is where the envelope of€the correlation function falls to a lower level than 1/e rather than the function. For a purely random surface such as is often found in grinding and similar processes, use can be made of the correlation length to define the number of degrees of freedom contained within a given length of profile. Once this is known it is then possible to determine the average behavior of the surface. An example of this is given in the chapter on instrumentation, where the degree of stylus integration is worked out using independent elements of the surface. The effect of the skid is also tackled this way. The degrees of freedom so obtained can also be used to estimate the variability of a parameter measured from the profile. Using the autocorrelation function or power spectral density as part of the basis for a typology is useful. It is relevant to determine the type or family to which the generated surface belongs. Peklenik made the premise that every surface can be described by a basic autocorrelation function. Owing to the ability of the correlation method to separate the random from the periodic components of the surface he proposed a typology system which, by means of the basic autocorrelation functions and/or a combination of them, could meet the requirements. Any typology of the correlation functions or spectral densities has to address the size as well as the shape of the curve. Peklenik proposed five shapes, as shown in Figure 2.59. To augment this classification in terms of size he advocated the correlation length and also the correlation wavelength which relate to the unit of size for the dominant random component and any dominant periodicity, respectively. The definition of the correlation wavelength is obvious; that of the correlation length is given in Equation 2.90 and tends to be more important because most finishing processes are random. The problem with such a typology is that to use it functionally requires a deep understanding of the way in which the surface configuration affects the function. This is not straightforward as will be seen in Chapter 7. The typology as proposed, however, is more likely to be useful in a manufacturing context because it is much easier to relate periodic elements to machine tool problems of long wavelength and the process in single point cutting for short wavelength and the random element to the process. In any case the two types of shape can be readily tied in with the method of production of the surface. That this typology has
48
Handbook of Surface and Nanometrology, Second Edition
(a)
Formula
Autocorrelation
Group
A(τ) A(τ)=const.
I
A(τ)=cos ωτ A(τ)=exp –dτ+cos ωτ τ
II
III
A(τ)=exp –dτ+cos ωτ τ A(τ)=Σ(exp+ sin+cos)
IV τ V
A(τ)=exp–ατ τ
(b)
Random profile
Amplitude modulated
Random telegraphic signal
Narrow-band frequency or phase modulation
Exponential
Modulated
FIGURE 2.59â•… (a) Peklenik classification and (b) example of ambiguity.
not been taken up in practice is due in part to the fact that manufacturers are still reluctant to depart from the idea of a “one number” surface, mainly because of cost and the practical difficulty of getting personnel to deal with any sort of statistical concept. Returning to the determination of the “size” element of the correlation function naturally brings in the concept of the correlation length. From the previous section it is clear that the autocorrelation and the power spectrum are powerful tools of characterization. However, there is a word of caution. Under some circumstances, see Equations 2.93 and 2.94 (and Figures 2.59 and 2.60) more than one type of surface can produce the same correlation function and power spectrum. This example shows a frequency-modulated waveform
Z Fm = cos ω ct − Dm sin ω st ⋅ sin ω ct
(2.93)
which could well be generated by a tool which has yawing vibration. Compare this with a surface exhibiting amplitude modulation of the form
Z Am = cos ω ct + M cos ω st cos ω ct
(2.94)
where Dm = Δf/fc is the modulation index for the case of frequency modulation (assumed to be small) and M is the depth of modulation for the amplitude modulation signal. Comparison of these two surface profiles shows that they could both have the same sidebands but different phase! They would give the same power spectrum yet they are produced by a different mode of vibration of the tool [48] see Figure 2.60. This ambiguous situation changes if D is increased to greater than three because extra sidebands show up with the
49
Characterization
Vector representation
Waveform
Fourier spectrum (not to scale)
1
1
M 2
ωs t
M 2
ωc–ωsωcωc+ωs
M 2 Amplitude modulation
1
1
D 2 ωst
D 2
ωc–ωs D 2
D 2
ωc–ωc+ωs
Narrow-band frequency modulation
FIGURE 2.60 Modulated signals showing how ambiguity arises.
extra series of the Bessel function describing the mode of modulation. To separate these two surfaces a classification of the amplitude density curve would have to be added to resolve the confusion. Kurtosis would make an ideal differentiator in these cases. Other ambiguities can arise because of the phase insensitivity. A classic example is that of a genuine random surface having an exponential autocorrelation, function, and the random telegraphic signal. Both signals in fact have Poissonian statistics but produce different waveforms [48]. 2.2.2.3.3 Indirect Parameters One mathematical tool often used in the derivation of indirect statistical parameters is the joint probability density function (JPDF) and, in particular, the multidimensional normal distribution (MND). The JPDF between variables Y1, Y2, Y3, etc. can be written as p(Y1, Y2, …, Yn,) and is taken to be the probability density that Y1 takes thevalue Y1 when variable Y2 takes the value Y2 and so on. Y1 and Y2 need not be the same type of variable, neither should they necessarily have the same dimensions. For instance, Y1 can be a length and Y2 an angle. It is often the case that Y1, Y2, etc., are themselves the result of a large number of random variables and under these conditions the central limit theorem holds, that is, the variables can be considered to be Gaussian variates and, furthermore, over a wide range of conditions the JPDF will be Gaussian. Assuming each variate has zero mean value the JPDF will have the form p(y1, y2, y3,..., yn) where
p( y1 , y2 ,..., yn ) =
1 (2 π)1/ 2 n M
1/ 2
− exp
∑
M ij yi y j (2.95) 2M
d11 M= d N 1
d12 dN 2
d1N d NN
(2.96)
and dij is the second moment of the variables yi yj; Mij is the cofactor of dij in M. This multinormal distribution for random variables is absolutely crucial in the surface properties field and is used in many places in typology and in Chapter 7 on function. Because profile ordinates are being considered here the symbol z will be used instead of the y used by Bendat [50]. Thus, the point probability density function of two height variables z1, z2 that are correlated by p is given by p(z1, z2): 1 z2 1 p( z1, z2 ) = exp − 1 2 π 2 2π(1 − ρ2 )
exp
− (z 2 − ρz1 )2 2(1 − ρ2 )
(2.97)
which is written in the form of a conditional probability density and an elementary probability density
p( z1 , z2 ) = p( z1 ) p(z2 z2 )
(2.98)
That is p(z2|z1) is the probability density that z2 takes the value z2 given that z1 has the value z1. In the unconditional form Equation 2.97 is p( z1z2 ) =
1 1 ( z 2 − 2ρz1z2 + z22 ) exp − 1 . (2.99) 2 1 / 2 2 π (1 − ρ ) 2(1 − ρ2 )
i , j =1
where |M| is the determinant of M, the square matrix
2.2.2.3.4 Parameters Involving Crossings Some investigators have derived statistical information from the number of crossings that occur at any level. Much of the original theory is derived from the work of Rice in
50
Handbook of Surface and Nanometrology, Second Edition
λ'a a
x
FIGURE 2.61 Profile-crossing parameters.
communication theory [40] and relates to random or pseudorandom waveforms. Longuet-Higgins [41] has expanded the work into two dimensions. Some typical parameters that have been derived are as follows. Consider the profile shown in Figure 2.61. It has been shown in terms of stationary random process theory by Peklenik [42] that the average number of crossings for unit length of profile is 1/λa where λa here is not the average wavelength as such but related to crossings at “a” 1/λ a =
∞
∫ z ′ ρ(a, z′)dz ′
(2.100)
0
and z′ =
dz dx
and the average thickness of the profile at height a, is given by γa γa =
∫
∫
∞
0
∞
.
(2.101)
z ′p(a, z ′)dz ′
1 z2 1 z2 exp − 1 2 exp − 2 2 (2.102) σ 2π 2σ σ 2 π 2σ
where z1 and z2 are considered to be independent and hence ρ = 0. From this Gaussian form σ 'is the standard deviation of the slope and σ is the standard deviation of the profile:
γa =
σ′ a2 exp − 2 σ 2π 2σ
σ a2 a λ a = π exp − 2 1 − Φ . σ′ σ 2σ
(2.103)
d 2 A(0) . dτ 2
For a equal to the mean of the surface, ca = 2π and c′a = 1/π For a equal to the σ level above the mean line, ca = 10.3 and c′a = 0.16. For instrumental reasons some sort of offset from the mean line is usually made. This is in case electrical noise is present which can happen at high magnifications. The advantage of such an approach is that deterministic surfaces can be treated in a similar way. A similar approach has been used by Sankar and Osman [49] who proposed a parameter called the MCE, the mean crest excursion. In addition they proposed the RMSCE, the root mean square crest excursion. Both of these are derived from p(λa), the probability density that the profile has a crest (or high-spot) width less than or equal to the specified value of λa about z. Thus MCE = E λ a =
RMSCE =
∫ λ p(λ )dλ a
a
∞
(λ a − MCE )2 p(λ a )dλ a –∞
∫
(2.106)
2.2.2.3.5 Power Spectrum Continuing the theme of a wavelength-conscious parameter naturally leads to methods which do not attempt to characterize the autocorrelation function but to condense the information in the power spectral density. One method due to Spragg and Whitehouse [13] involves the estimation of the moment of gyration of the power spectrum (the RMS frequency) by a direct measurement of the RMS slope and the profile RMS value. It has been shown that if ωRMS is the RMS angular frequency ∞
(2.104)
a
Similar expressions have been developed for the valleys but only give the same information for a random wave. (Note that λa is not the average wavelength as defined earlier and described below.) As in the previous example they proposed counting profile crossings at a height above the mean line. This time, however, they chose a height of the Ra value rather than the RMS Rq value above the mean line.
ω
2 RMS
∫ ω p(ω)dω = ∫ p(ω)dω 0
2
∞
(2.107)
0
From these
σ ′2 = −
p( z )dz
a
1/λa corresponds to the high-spot count sometimes used as a parameter of the surface. Notice that the term for γa is normalized with respect to a unit length. For the case when the profile is Gaussian in form and of zero mean p( z11 z2 ) =
where ca and c′a are constants for any given level at which the crossings have been counted and γa is the average number of crossings per unit length at level a. Information about the correlation function is inherent in σ′ because it is well known that the variance of “z' ” is related to the correlation function by the formula
σ ′ = ca σ λ a γ a = ca′ .1.λ a
(2.105)
Similarly, it can be shown that
E (z ′ 2 ) = σ ′ 2
(2.108)
51
Characterization
P(λ) 1µm 0.1mm
λ P(λ)
Average wavelength
5µm 0.1mm
λ P(λ)
20µm 0.1mm
λ
Average wavelength
FIGURE 2.62 Average wavelength and power spectrum.
= ( Rq′ )2 =
1 2π
∫
∞
ω 2 P(ω )dω.
–∞
(2.109)
The power spectral density is related to the autocorrelation function by means of Fourier transforms. Thus the wellknown relationship is
p(ω ) = A(τ) =
∫
1 2π
∞
−∞
∫
A(τ)cos(ωτ)dτ
∞
P(ω )cos(ωτ)dω.
−∞
(2.110)
(2.111)
The power spectrum P(ω) is related to the Fourier spectrum of the surface by
1 2 P(ω ) = lim F (ω ) . L →∞ L
(2.112)
The value of A(τ) at the origin is the zero moment σ2, the variance of the surface equal to R2q. Equations 2.110 and 2.11 are cosine transforms because both P(ω) and A(τ) are even—the phase has been destroyed. This is one of the advantages of using random processes— one less random variable is present. Consequently, P(ω) the power spectral density is stable. Hence
1 λ = ω 2π
(2.113)
and
λ = λ AMS = 2π
characteristics are stationary over the evaluation length. For convenience the λq value is often replaced by the λa value, the average wavelength alternative. Some examples of the parameter λa value are shown in Figure 2.62. The essential practical detail that needs to be taken into consideration in autocorrelation as well as power spectral density (PSD) measurement is the high-frequency content of the signal allowed through by the instrument. The change in parameter value as function of frequency cut is profound. As an example the way in which ω RMS changes with high cut c is given by [13]:
Rq Rq′
(2.114)
where Rq = σ, Rq′ = σ ′. This technique, as in the level-crossing methods for autocorrelation, is completely general, providing that the
d (ω c2 ) = P(c) dc
c
∫ (c 0
2
− ω 2 ) P(ω )dω / ( SP(ω )(dω )2 . (2.115)
It will be demonstrated in a later Section 2.4 how it is possible to build up a comprehensive measuring philosophy in roundness based upon such a system. 2.2.2.3.6 Asperity Definitions and Characteristics Some characteristics of interest to the metrologist have already been studied in different disciplines, for example, the distribution of maximum values in statistics as in communication theory (Rice [40]). The conventional way to calculate average peak height from a surface profile is to split the profile vertically into equal height intervals and then to count the number of peaks within each interval over the profile length. These peak counts, sometimes called peak frequencies, are plotted as a function of height; the resulting graph is called the peak distribution histogram. If these counts at each level are divided by the total number of peaks within the profile length assessed the plot becomes a peak probability density. This is possible because the area of the plot is unity. The average peak height is obtained from this by working out the height of the center of gravity of the graph from the height datum. In the above approach the count of peaks within each height interval can be regarded as an attribute. Each peak
52
Handbook of Surface and Nanometrology, Second Edition
is only registered by its presence. In what follows it is suggested that there is another way to arrive at an estimate of peak probability. This method does not derive the peak probability curve using the peak count. Instead the “extent” of profile surrounding each peak which satisfies certain discrete peak criteria is measured and summed for each height. These sums of “extents” are normalized within each interval for all heights by the total length of assessed profile. In this way another way of generating a peak probability curve is realized in which the attribute of peak presence has been replaced by the measurement of a peak property (i.e., the extent). It turns out that this “extent” of peak-like property is related very strongly to peak curvature (i.e., each peak is “weighted” by its curvature). It has to be pointed out that, in the direct probability approach, neither the actual “extent” of peaks or their curvature are measured. These peak properties are intrinsically contained within the definition of probability (see for example Equation 2.116) and the limits of the integration. The fact that there is no need to measure curvature of the peaks and yet still include the effect of curvature (i.e., the extent along the profile describing the “thickness” of the peak) is very attractive (see Equation 2.88). In the following sections, it will be shown that the values of average peak heights (and RMS heights) are different using this measure of probability. It is suggested in this paper that the two methods are complementary. The peak count method may be more useful in electrical and thermal contacts because the actual numbers of contacts are involved whereas the latter could be useful in loaded contacts [1] (Figure 2.63), although this Â�figure is somewhat idealized as shown in Chapter 7. The starting point is the joint probability density of the surface height, the slope and the second differential z″, (here approximated as the local curvature). This is represented as p(z, z′, z″). At this stage the JPDF is quite general. The probability of peaks occurring between zs and zs + δz having a curvature of between z″ and z″ + δz″ and a slope between 0 and δz1 is therefore
In Equation 2.117 δz is small when compared with z and δz′ is small when compared with z′ (i.e., much more than an order of magnitude smaller) and p′(0) is the probability density of the slope term at between zero and δz′. The local length of surface over which this peak condition holds is given by δz/z″. The term δz/z′′ is in effect the “thickness” of a peak of curvature z″ between height z and z + δz and having a slope of between 0 and δz/z′ (Figure 2.64). Given the probability of a peak, the number of peaks per unit length, N(zs), is obtained by dividing Equation 2.86 by δz′/z″ in the same way as Bendat [50]. Thus the tribological approach is given by Whitehouse [51] as,
P ( zˆ ) =
zs +δ z
δz ′
∫ ∫ ∫ zs
0
zs + δ z ′′
0
p( z , z ′, z ′′)dz ′′dz ′dz (2.116)
N ( zs ) = δz ′p′(0). p( z , z ′′)δz ′′δz /δz /z ′′
= p′(0) p( z , z ′′) z ′′δz ′′δz.
The peak count is basically the number of times that the profile height falls between zs and zs + δz when the slope of the profile is between 0 and δz′ and the curvature is between z″ and z″ + δz″ per unit length. The distance information is not omitted. For a given z and slope range (i.e., δz′ the count for unit distance) is determined for a given z″ by the extent of x in which z″ is in the 0–δz′ range (Figure 2.64). The count is remembered but the x values are not. So for the peak probability the x values are remembered and the peak count is not and for peak count Equation 2.87 the count is remembered but the x values are not. The two parameters are not the same: they are absolutely complementary. It may be that a parameter derived from both approaches is possible. It is useful to compare Equation 2.118 with Equation 2.117. At first glance this is a comparison of a count of peaks with a probability of peaks. There is, however, a completely different interpretation of the probability Equation 2.86; it can be construed as the sum of the count of peaks each weighted by their “thickness.” Take for example, Equation 2.88 for the probability of a peak at a height between z and z + δz,
( z z ′p′ ( o ) p(z , z ′′ ) δz ′′δz ⇒ ( p′ ( o) . p , z ′′ )) z ′′ δz ′′ δz.(δ δ z ′ /z′′). probability
count
thickness
(2.119)
= δz ′p′(0). p( zs , z ′′)δz ′′δz ′.
(2.117)
In words, the probability of a peak P( zˆ) does not only depend on the number of peaks but it also automatically takes into
Surface 1
Can be reduced to
Surface 2
FIGURE 2.63â•… Surface contact.
(2.118)
53
Characterization
z+δz
z
Height domain
x z δz' 2
– δz' 2
δz' 2
z'
Slope domain
x – δz' 2 Curvature z˝ in slope domain Extent of x over which conditions for a discrete peak hold
FIGURE 2.64 Peak weighting.
account their physical dimension as revealed by the radius of curvature 1/z″. The total peak probability between z and z + δz is given by P( zˆ ) where
represent both the unit functional event (contact points) and their distribution in space). Consider now the peak count. The total number of peaks per unit distance at height z is given by N(zs) where
zs + δ z 0
P ( zs ) = δz ′p′ ( o )
∫ ∫ p( z, z ′′) dz ′′dz, zs
(2.120)
−∞
which represents what is in effect the count of all peaks at z each weighted according to their radius of curvature 1/z″. This is a measure of the total length over which the profile at height between z and z + dz satisfies the peak criterion. When divided by the profile assessment length, this Equation 2.120 represents the peak probability. For any height between z and z + dz there will be a family of probabilities each made up of counts of peaks, and each family having associated with it a different radius of curvature. Exactly how large the probability is depends on the form of 1(z, z″). No assumptions about the nature of p(z), p(z, z″), or p(z, z′, z″) are needed. A point to be aware of is that the mechanism of contact is made up of two elements, the behavior at a “typical” contact and the distribution of such contacts in space. The probability of peaks at z gives in effect the total length of “peak-like” surface at z which has the capability of supporting normal loads. It does this because the definition has first isolated the peaks and then lumps them together after multiplying by 1/z″. This weights them in importance according to 1/z″. The peak count by contrast is an estimate of the distribution of peaks (i.e., how the number of peaks per unit length varies with height). The total length of xs values mentioned above is expressed as a fraction of the whole length of profile. So the peak probability and peak count taken together can satisfy a functional requirement for surface parameters (i.e.,
z s + dz
0
zs
−∞
N ( z s ) = p ′ ( 0)
∫ ∫ p(z, z ′′)z′′dz ′′dz
(2.121)
and is a simple count of all peaks at z irrespective of their curvature divided by the total profile length. Equation 2.121 should be compared with Equation 2.120. It is evident that probability and frequency of occurrence are not the same. This can be seen in Equation 2.119. The standard way of evaluating the average peak height is via the count (or frequency of occurrence). Thus the average peak height obtained conventionally, zˆc is given by ∞
δzp′(0) zˆc =
0
∫ ∫ z. p(z, z ′′)z′′dz ′′dz
−∞ −∞ ∞ 0
δz ′p′(0) x
∫ ∫ p(z, z′′)z ′′dz ′′dz
.
(2.122)
−∞ −∞
An alternative way using probabilities of peak rather than the frequency of occurrence of peaks is suggested here. This gives zˆ p where ∞ 0
δz ′p(0) zˆ p =
∫ ∫ zp(z, z ′′)dz′′dz −∞ −∞
∞ 0
δz ′f (0) ×
∫ ∫ p(z, z′′)dz ′′dz
−∞−∞
(2.123)
54
Handbook of Surface and Nanometrology, Second Edition
Only if the value of curvature z″ is fixed or its range severely restricted or if z″ is independent of height z can Equation 2.122 be equal to Equation 2.123. As none of these are probable in practice, z p ≠ zc which is a general result and not dependent on the form of p(z, z″) z p could be used as an alternative measure of average peak height rather than zc and peak probability as explained above could perhaps be more meaningful than peak count in contact situations. The fact is that for any given z there are a number of peaks with curvature z″1, say n1, a number with curvature z′2, say n2, and so on which are taken into account with peak probability but not peak count. The number of peaks at z is n1, n2 … This is just the number of peaks at z. Nothing else is recorded. If the waveform is z and its derivatives are z′ and z″
which yields cofactors
z′ =
dz dx
z ′′ =
d 2z . dx 2
dz1 =
∫
0 −∞
p( z1 , 0, z ′′) z ′′dz ′′.
(2.125)
This equation shows the restraints for a maximum, namely that z′ = 0 and z″ = 0. Similar equations hold for the valleys. Note that all curvatures are lumped together! In the case of random waveforms this distribution approaches a Gaussian form due to the central limit theorem. Notice the similarity between this formula and the one for the average number of crossings per unit length of the profile. The coefficients in the correlation matrix M of the multinormal distribution of Equation 2.95 become E (z 2 ) = σ 2
E ( z ′) 2 =
− d 2 A(τ) = σ ′ 2 = A ′′(0) dτ 2
E ( z , z ′) = 0 E ( z ′, z ′′) = 0
+ d 2 A(τ) = − A′′(0) dτ 2
(2.126)
− d A(τ) = Aiv (0). dτ 4
d n A(τ) = An (0 ) d n τ τ=0
σ 0 A′′(0)
0 − A ′′(0) 0
A′′(0) 0 iv A ( 0)
M
1/ 2
1 × exp − (m z 2 + m z 2 + 2m13z1z ′′) (2.130) 2 M 11 1 33 0
The expected number of peaks per unit length at a height in between z1 and z2 + dz is given by pp(z1) dz1 PP (z ) =
1/ 2 dz1 1/ 2 π z2 − exp + M m m z 3 1 11 2 M 2 π 3/ 2 M 33 2m 33
× exp
z 2 1 + erf m13 z1 1/ 2 2σ 2 2 M m13
(2.131)
where erf ( x ) =
2 π
∫
x
0
exp(−t 2 )dt .
(2.132)
For large z it can be shown that the expected number of peaks per unit distance lying above the height a, Pp(a), is given by
PP (a) =
( )
1 – σ ′2 2π σ 2
1/ 2
exp
( 2–σa )(σ′ = E(z′ )). 2
2
2
2
(2.133)
This corresponds to the number of positive crossings at height a. The total number of peaks per unit distance of any height is obtained from Equation 2.125 by integrating with respect to z and z″, yielding 1 Aiv (0) 2 π − A ′′(0)
1 N= π (2.127)
1/ 2
1 = 2π
∞
ω P(ω )dω 0 ∞ ω 2 P(ω )dω 0
∫ ∫
1/ 2
4
1/ 2
=
1 m4 2 π m2 (2.134)
∞
0 ∞ P(ω )dω 0
∫ ∫
1/ 2
ω 2 P(ω )dω
=
1 − A′′(0) π A(0)
1/ 2
=
1 m2 π m0
1/ 2
(2.135)
In general average number of zero crossings of kth derivative of the profile
Then the multivariable matrix M becomes 2
2π
3/ 2
Furthermore it can also be shown that the number of zero crossings of the profile N is given by
4
For simplicity the notation below is used:
1
p( z1 , 0, z ′′) =
E (z , z ′′) = E ( z ′′ 2 ) =
from which the probability density becomes
(2.124)
The probability for a peak occurring at a height between z1 and z1 + dz is dz1
m11 = − A′′(0) Aiv (0) m13 = ( A ′′(0))2 m33 = − A′′(0)σ 2 (2.129)
(2.128)
1 Nk = π
∞
0 ∞ ω 2 k P(ω )dω 0
∫ ∫
ω 2 k +2 P(ω )dω
1/22
=
1 − A 2 k + 2 (0 ) π A 2 k ( 0)
1/ 2
(2.136)
55
Characterization ∞
from which, by using Maclaurin’s series,
τ2 τ4 A(τ) = A(0) + A′′(0) + A IV (0) + . 2! 4!
(2.137)
=
1 m4 4 π m2
1/ 2
m2 m0
+
1/ 2
1 A0iv (0) 4 π − A′′(0)
1/ 2
A′′(0) + σ2
1/ 2
(2.138)
where m4, m2, m 0 are the fourth, second, and zeroth moments of the power spectrum, which give the result that pp = density of maxima over mean line = 1/2 total maxima density + 1/4 density of crossings. Also, density of maxima below mean line = 1/2 total maxima density –1/4 density of crossings. A corollary of this is that
1 densityof crossings 2 p p+ − p p− = 1 / λ q .
PP + − PP- =
(2.140)
∞
zp
p
–∞ ∞
−∞
0
p
= σ 2 /π
(2.141)
p
(2.143)
∞
p
k 2 π k 1 − (k / 2)2 + + sin −1 . (2.144) 4 2 + k k 2
Also z p− = − σ 2 /π
k 2 π k 1 − ( k / 2)2 − + sin −1 . (2.145) 4 2 − k k 2
Figure 2.65 shows how the respective peak height properties change with k. The physical interpretation of k is that of a bandwidth parameter. It tells the shape of the spectrum. When k = 2 it corresponds to a very narrow bandwidth surface; when k = 0 a wideband spectrum occurs as seen in Figure 2.66. By changing k many surfaces can be simulated. Therefore the tribological behavior of many types of surface varying from the purely random k~0 to nearly deterministic k~2 can be investigated. The k value is a characterization of the surface and is especially useful in contact problems involving peak and valley behavior. This is in effect a typology based upon random process theory. This concept of taking the ratio of the zero crossings to the peak count was used extensively in the USSR [12] by Lukyanov. As can be seen with reference to the definitions given so far the value k can be related to S and Sm k = 2 S /Sm
(2.146)
Mean positive peak
(2.139)
This definition of RMS wavelength shows how it may be obtained without having recourse to high-spot counting which may not be as accurate as peak counting on a profile obtained from a real surface. Mean peak height z p
∫ zp (z)dz . = ∫ p (z)dz
∫ zp (z)dz . ∫ p (z)dz 0
In principle, by measuring Ni, i = 1, 2, … k, the autocorrelation function can be found from this equation. This assumes that the profile is Gaussian and that the autocorrelation is differentiable at τ = 0, which is not the case for exponential correlation functions, nor for fractal surfaces where all the derivatives at the origin are undefined. Other peak characteristics of particular significance in surface topography can be found in terms of the ratio of maxima to crossings on the profile. Peak density above mean line For example, the peak density above the mean line is given ∞ by ∫0 pp(z) dz where pp(z) is as given in Equation 2.130. Here the peak density is as defined by Whitehouse [35] simply counting peaks. After some manipulation, the peak probability density pp above the mean line [51] is PP =
z p+ =
Mean peak
0.8
Mean negative peaks for negative ordinates
0.4
0
k
2
FIGURE 2.65 Properties of peaks as a function of the type of surface. P (ω)
k large
P (ω)
k small
This can be evaluated using Equation 2.131 to give
zp =
σk 2
π 2
(2.142)
where k is the ratio of density of zero crossings to maxima in unit length. The mean peak height above the mean line can be similarly found. Thus
ω
ω
FIGURE 2.66 Shape of power spectrum as function of surface characteristic k.
56
Handbook of Surface and Nanometrology, Second Edition
This k is not to be mistaken for the k surfaces of sea reflection discussed later in the context of optical scatter in Chapter 7. The use of k (or α described in areal parameters) is a means of making a typology from the shape of the power spectral density rather than using the Peklenik typology based on the correlation function. They are, however, both doing the same thing only in a slightly different way. In the foregoing analysis the importance of the zero-crossing approach should be noted. The reason for this is the ease with which crossings (and peak counts) can be measured from a chart. The count does not have to be very accurate in order to get some idea of the density of crossings. To pursue this crossing initiative further, consider the possibility of estimating the correlation function itself from crossing theory. It can be done quite easily as will be seen. Apart from being useful as an estimate such techniques can be useful as checks on computed results. 2.2.2.3.7 Cumulative Distributions and Peaks Counts The well-known curve describing the way in which the material to air ratio changes with height has many names. It started as the Abbott–Firestone curve and now is called the material ratio curve MR(z). Although it has also been rerred to as “Tragenteil” early on by Swedish engineers. It is defined as 0
MR( z ) =
∫ p(z)dz,
(2.147)
z
where p(z) is the probability density of the profile taking the value z. This parameter is one of the most used of all parameters and is the basis for many modern parameters namely Rpk , Rvk [37]. The problem with the material ratio curve is that it relates to the whole profile and does not consider peaks as such. What is proposed here is a variant of MR based on peak probability rather than the whole profile probability. Thus the peak probability ratio PPR (z ) is given by ∞
0
∫ ∫
PPR ( z ) = p′(0)δz ′ p(z ) p( z ′′ /z )dz ′′dz
(2.148)
∞
z
by expressing p(z, z″) in the conditional form p(z).p(z″/z). Normalizing Equation 2.148 gives Equation 2.149 in which it is seen that MR information is not lost. It is in effect modulated by the peak information. ∞
PPR( z ) =
∫
0
∫
p ( z ) p ( z ) dz ′′dz
(2.149)
z ∞ MR( z )
peak factor
Obviously, the mechanism of measuring PPR(z) from a profile would be slightly more complicated than that of MR but not prohibitively so. As each peak between z and z + δz is recognized and counted it is weighted (i.e., multiplied by the measured value of the radius of curvature for that peak) before being added to the accumulator representing the
y
Flat surface Surface profile
This appears to be loaded
This peak has been loaded
FIGURE 2.67 Apparent peak loading. δy
Profile
FIGURE 2.68 Discrete model of profile.
probability value at that level. In practice this weighting is not usually necessary. It is taken account of automatically, as will be seen later. It is suggested here that this curve of PPR(z) could possibly be more meaningful than the MR curve in some contact situations and possibly in wear and friction because it is highlighting exactly that part of the waveform which is capable of supporting normal load. PPR (z ), in effect pools the advantages of a peak (which is the latter part of Equation 2.149) with that of the material ratio (which is the first part of the same equation). The corresponding cumulative peak count ratio PCR(z) gives only the number of peaks down to level (z) as a fraction of the total number of peaks i.e., ∞
PCR (z ) =
0
∫ p(z) ∫ p(z ′′ /z)zdz ′′dz. z
(2.150)
∞
Figure 2.67 shows the mechanism of the loading of a peak on the surface. It is seen that the effect on the larger peaks is straightforward. An elastic compliance is shown. what is also shown is a sympathetic compliance with peaks not being contacted. This possibility is discussed later when considering the Gaussian case. Figure 2.68 shows that if the quantization interval is δz then the probability of peaks at z is obtained by adding the width of peaks between the interval z and z + δz rather than the width of the profile at z as in the material ratio evaluation. The PCR (z ) is therefore easy to measure. In order to get some feel for the proposal it is useful to consider the case when the probability densities can be considered to be Gaussian. This is not a bad assumption in practice because many finishing processes have this property and, in any case, the gap between contacting surfaces is more than likely to have a Gaussian characteristic than either individual surface. 2.2.2.3.8 Gaussian Statistics (Profile) The multi-normal distribution is used to calculate the relevant statistics (after Rice [40]). Thus
57
Characterization
p ( z , o, z ′′ ) =
1
1 3
1
(2π ) 2 M 2
1 (m m z 2 + 2m22 zz ′′ + m0 m2 z ′′ 2 ) × exp − 2M 2 4 (2.151)
where |M| = m2 (m 0 m4 –m22), m0, m2, and m4 are the variances of z, z′, and z″, respectively. 2.2.2.3.9 Extrema Statistics (Gaussian Analysis) Using Equation 2.151 in Equations 2.91 and 2.92 and noting that p′(0) is removed from the distribution by normalization the well-known result for the average peak height is found. Thus zˆc is given by
zˆc =
π m2 . 2 m4
(2.152)
This result has been well documented for many years. See for example Bendat [50]. If, however, the average is found by probability of peaks and not frequency of peaks zˆ p results. Where
zˆ p =
2 m2 . π m4
(2.153)
Notice that zˆ p is much lower than zˆc in the profile waveform illustrating that more emphasis has been given to the “wider” peaks found lower in the profile than zˆc which assumes all peaks are of equal weight (i.e., each peak has the value unity). The ratio of Equations 2.152 and 2.153 is the considerable value of π/2! This represents a very considerable difference in height. It could be interpreted, therefore, that the average height of peaks weighted by their radius of curvature is a factor of π/2 lower than the average height of all peaks [51]. However there is another interpretation. Letting
b=
m2 , m0 m4
(2.154)
where b is a measure of the bandwidth of the surface spectrum gives the value of zˆc as
zˆc =
π b m0 2
(2.155)
and
zˆ p =
zˆ =
2 b m0 . π
2 m0 . π
2.2.2.3.10 Cumulative Distributions Material Ratio Parameters (Gaussian Analysis) The material ratio curve is well known and often used. It has the form given in Equation 2.157 and Equation 2.147. Thus
MR ( z ) =
∫
∞ z
p ( z ) dz ,
(2.157)
which for a Gaussian distribution, becomes
MR ( z ) = =
∫
∞ z
1 2π
1 z2 exp − dz 2m0 m0
1 z 1 − erf . 2m0 2
(2.158) (2.159)
This distribution is obtained from all of the profile signal and does not separate peaks. The comparable cumulative peak probability for a Gaussian distribution of the profile is PPR ( z ) where ∞
PPR( z ) =
∫ P(zˆ)dz z
where the probability of a peak within the interval z and z + δz is
If b = 1 which corresponds to a narrow spectral band surface such as might be found in general turning or diamond turning. Then
Under these circumstances when b = 1, (i.e., nominally a sine wave surface) the average height of the “significant or weighted” peak is equal to the Ra value of the surface—the AA for the profile above the mean line. In this interpretation obviously the symmetrical Ra level below the mean line is invalid. In Equation 2.124 the value of m0 is Rq the root mean square deviation of the profile about the mean line. – Using the same example, zˆc the “all peak” average height, can be interpreted as the amplitude of the dominant waveform in the narrow band spectrum (i.e., the amplitude of the feed mark) because it is π/2 larger than the average (Ra) of such a waveform; it corresponds in fact to Rp. The interpretations of zˆ p and zˆc can in this specific case of b = 1 be identified with the traditional surface parameters Ra, Rq, and Rp. It is interesting to note that for this type of surface the well known and often used Ra value has a peak interpretation as well as the traditional profile representation [1, 2]. One question that has not been answered in the above section is how the cumulative distributions of peak probability and peak count compare with the material ratio curve for the Gaussian case. This will be addressed in the next section.
(2.156)
1 z2 (1 + erf ( HKz )) δz. (2.160) exp − 2 m0 4 π m0 m2
where H and K are defined below. The cumulative version of Equation 2.160 appears not to have a closed solution. However, some idea of its form can be obtained by taking just the first term of the series for the error function.
58
Handbook of Surface and Nanometrology, Second Edition
P
Cumulative frequency peak Cumulative probability peak
P2
P3 H
H2
Material ratio
FIGURE 2.69â•… Cumulative peaks.
FIGURE 2.70â•… Types of peak. Showing correlated peaks P and independent peaks H.
This gives the cumulative peak distribution PPR PPR ( z ) ≈ MR ( z ) +
2 m2 M 1/ 2 exp(− P 2 K 2 z 2 ) (2.161) π m 0 m4
m2 , P= m0
H=
m4 , K= m2
m2 2M
(2.162)
H appears in Equation 2.160 and P in Equation 2.161. Equation 2.163 clearly shows the two components making up the PPR; the material ratio term plus a term involving peaks only. (P is some measure of closely correlated peaks above z.) The equation therefore shows in Figure 2.69 that any load could be resisted at a higher level using the peak probability than it would for the material ratio curve. It is the contention in this paper that the PPR approach could be more likely to satisfy the practical situation of contact and wear than MR(–)! The important point is that there is more information in the statistics of the surface profile and no doubt also the areal geometry than has hitherto been extracted. The value of the peak count between z and z+δz is well known [40] but it can be expressed in a slightly different form. Thus if M is the determinant of p(z, z′, z″) then, NC ( zˆ) =
1
M2 H +z exp(− P 2 K 2 z 2 ) + . 4 π m0 m0 m4
1 3
(2 π ) 2
−z2 (1 + erf ( HKz )). × exp 2 m0
(2.163)
The count ratio down to z is given by
∞
∫ N ( z ) dz = PCR ( z ) z
c
(2.164)
1 PCR ( z ) = P (1 − erfPK ( z ) ) 4 π A
1 H ( exp ( −( z )2 / 2m0 ))(1 + erfHK ( z ) ). + 4 π (2.165) B
Equation 2.165 breaks down in a simple way. The component A is the first term and B is the second term shown in Figure€2.71 and are clearly higher than the PPR. Two features of the cumulative peak count given in Equation 2.165 stand out. First is the fact that there is no identifiable
Cumulative peak count A-term (in Ps) B-term (in Hs)
FIGURE 2.71â•… Breakdown of cumulative peak count.
MR(–) term within it, which is not surprising considering the way in which PCR is constructed from the profile; spacing information in the form of the P and H multipliers is preserved. The second feature is that the equation clearly splits into two components: the A part in which P occurs and the B part in which the parameter H occurs. In random theory P is a measure of peak spacing and H is a measure of zero crossing spacing. It can be shown that the A term is a measure of the count of peaks above ( z ). These peaks must have valleys also higher than ( z ) and the B term is a measure of those peaks above ( z ) which have valleys below ( z ) (see Figure 2.70). These two components of peaks can roughly be identified in Figure 2.53. The H terms in B in Equation 2.165 can be thought of as the large peaks which directly deform and the P terms in A those peaks which indirectly deform. The situation is more complicated than this but the foregoing description is a possibility. The two different types of peak relative to ( z ) (i.e., the Ps and Hs) must have different functional properties. This suggests that the cumulative peak count PCR should be split into two component curves (instead of just one as in Figure 2.52) and that both of these curves should be used. A typical case is shown in Figure 2.71. A physical interpretation of these components is that for any given ( z ) the A curve (in terms of P) represents peaks which are highly correlated with each other whereas the B curve represents a count of peaks which are independent [52]. 2.2.2.3.11â•… Discussion of Peak Parameters The section above indicates that obtaining peak parameters by using the peak “count” distribution used extensively in communication theory may be somewhat misleading to
59
Characterization
2.2.2.4â•…Areal Texture Parameters, Isotropy and Lay (Continuous) Methods of measuring and specifying the surface over an area are now often investigated. Areal information from a surface falls into a number of categories: one is statistical average values, another is the structure, and a third is defects or flaws. The last two can be found from purely qualitative information, that is a visualization of the surface. The former is concerned with quantifying the information in the z direction primarily but increasingly in the x and y directions also. The structural problem will become more and more important in non-engineering fields as will be seen, for instance, in biological applications. The form of areal investigation has of two types: the first has been to measure deterministic
parameters in a large number of places and then specify a spread which the parameter might take, and the second has been to try somehow to predict from a few profiles or a single profile what the areal properties really are without measuring the whole surface. It is the areal characteristics which are important in function. The biggest problem is that if the area is completely measured the amount of data needed may be too large to handle. Because of the amount of data the most obvious way of attempting to specify areal characteristics is to use the statistical methods described above. This is precisely what has happened. Because the work done in these areas is as yet relatively small, emphasis is given to short-term work which will be likely to be of practical use. However, some consideration of new tools in the analysis is relevant which, although restricted to random surfaces, does enable some light to be thrown onto those parameters having tribological significance. Later, some practical cases of techniques, rather than analysis, will be discussed which may ultimately provide a more general basis for future work. In particular the Wigner distribution methods will be considered. Ultimately, the worth of either theoretical or practical methods will be judged by their use in the field. This has yet to be demonstrated fully where random processes are concerned. 2.2.2.4.1â•… Statistical Assessment over an Area One way of doing this has been suggested by Peklenik and Kubo [53]. They have proposed a two-dimensional mapping of correlation functions split broadly into two fields; one where the surface is basically anisotropic and the other where it has only small variations from isotropic symmetry. Peklenik tackled the first and Kubo [54] the second. Fundamentally the distinction between the two approaches is the coordinate system used; Peklenik uses Cartesian coordinates (Figure 2.72) and Kubo uses polar (Figure 2.73). Neither of these methods has attracted much attention. Other practical methods of determining areal properties will be dealt with in Section 2.3.7 for the digital implications and in Chapter 4 on instrumentation. z
∆y
x Correlation length
tribologists. Using the peak count implies that every peak in the count is the same. This is not true for surfaces. It is only by resorting to the probability of peaks that some measure of the different peak properties is possible. In this case the peaks are effectively weighted by their radius of curvature. This reflects to what extent the surface surrounding the actual maxima lies within the boundaries set by dz′ and dz″ which are arbitrarily small and only need to be applied consistently throughout the waveform to be entirely valid. It is shown how large differences between estimated parameters can result depending on whether peak “count” probability or just the peak “probability” is used. A displacement of π/2. Rq downward when assessing the average peak height would probably be significant in contact situations such as mechanical seals for example. Another observation is that the peak probability distribution could be more realistic than the material ratio curves used extensively in industry which completely ignore the influence of peaks when carrying load. Rpk, the highest parameter of the material ratio curve, is loosely described as a “peak-like” parameter, which is a highly optimistic description. The cumulative peak probability curve could well be a better indication of the load carrying capability and wear properties of a surface than the material ratio curve or the cumulative peak count. However, the latter is useful for a different reason; it not only provides spatial information in the form of peak separation, it can also give an insight into spatial correlation between peaks. This aspect of possible contact behavior is not reported in this paper. In practice not all peaks make contact; it is far better to consider contact as a “gap” property between two rough surfaces rather than a rough surface touching a smooth as in this paper. Nevertheless the argument remains valid. As a next step some practical experiments need to be carried out to see if direct probability measures, as recommended for tribologists in this paper, can be carried out. Finally, areal measures rather than profiles should be investigated. However, it seems obvious that equal if not greater divergence will occur in parameters obtained by the two paths, that is peak probability versus peak frequency (count) of occurrence. Ideally, it should be possible to contrive a metrology scheme which uses the benefits of both methods.
∆y
y
FIGURE 2.72â•… Correlation length map (rectilinear).
60
Handbook of Surface and Nanometrology, Second Edition
These formulae are used extensively in the optical work on Fourier analysis in Chapter 4. Another useful formula is the moments of the spectrum, mpq. Thus ∞
Profile
m pq =
∫ ∫ P(u v)u v du dv 1
P q
1
(2.168)
–∞
from which σ 2 = m00 .
θ
(2.169)
It is possible to extract the information about a single profile from these formulae by noting that
Anisotropic
∞
Isotropic
P(ω ) =
∫ P(u v)dl
(2.170)
–∞
where
θ
l = (u 2 + v 2 − ω 2 )1/ 2 .
Some features of importance in tribology can be estimated analytically by using the MND and the parameters
FIGURE 2.73 Correlation length map (polar).
The Peklenik and Kubo methods are just techniques for extending the use of autocorrelation to areas, not specifically for determining new areal parameters. This was achieved principally by Longuet-Higgins and later Nayak. The advantage of the Peklenik–Kubo method is that it provides some tools for the description of surfaces which are not necessarily random in nature. Other techniques have been advocated which consider only random and similar surfaces. Such a piece of work has been illustrated by Nayak [43], who transposed some of the work of Longuet-Higgins to manufactured surfaces rather than sea waves. The importance of this original work was that it shows the errors which can result when extrapolating the peak and valley heights obtained from a profile to that of the whole surface. Longuet-Higgins quantifies the errors, pointing out that by using a simple profile the higher crests and troughs will sometimes be missed. The analysis hinges again on the multivariate distribution and is similar to the Rice technique except that it is now in two independent dimensions rather than one. (This is defined as the areal case.) Once the areal case is considered the formulae become correspondingly more complicated. For example, the two-dimensional autocorrelation function becomes A(τ, i) where 1 L1L2 →∞ L L 1 2
A ( τ, i ) = lim
L1 / 2
L2 / 2
– L1 / 2
– L2 / 2
∫ ∫
z ( x , y ) , z ( x + τ, y + i ) dx dy
z,
y being used as the other independent variable and z the variable in the plane out of the surface. Similarly the spectrum becomes ∞
∫∫
∞
−∞ −∞
A ( τ, i ) exp[ − j ( τu + iv )] dτ di. (2.167)
dz dz ∂2 z ∂2 z , , , and dx dy ∂x 2 ∂xy
∂2 z . ∂y 2
(2.172)
Using these the summit curvature, slopes, etc., can be found for the surface, at least on a microscopic scale. For example, the distribution of summit heights can be found by imposing the constraints that dz dz d2z d2z = 0, = 0, 2 < 0 , 2 < 0 dx dy dx dy 2
and
d 2z d 2z d 2z − > 0. dx 2 dy 2 dxdy
(2.173)
Then the probability of finding a summit at a height between z and z + δz in an area dA is δz
∫∫∫ ∫∫
dz dz d 2 z d 2 z dz dz d 2z f z , , , 2 , 2 d , , 2 etc. dx dy dx dy dx dy dx (2.174)
where the limits of integration have to obey the constraints given. A key parameter that Nayak highlights is the ratio of some of the moments. In particular, for a Gaussian isotropic surface the parameter α is given by
(2.166)
1 P ( u, v ) = 4π2
(2.171)
α =
density of maximaa m0 m4 which in effect = 2 (m2 ) density of positive crossing
2
(2.175) and is obviously closely related to k used in the previous Section 2.2.2. The parameter α (or k) can be useful in determining the reliability of parameters.
61
Characterization
In Equation 2.175 m0 = m00 = σ 2 m 2 = m02 = m20 the mean square slope m4 = m40 = m04 = 3m22 the mean square second differential. The moments with double subscripts represent the nonisotropic case. It is known that all the relevant characteristics of stationary profiles can be expressed by means of the spectral moments. (Later it will be shown how these moments can be estimated by methods other than crossing and peak counts.) For the areal surface the moments mpq are given by m pq =
∫∫ ω ω p(ω ,ω )dω dω p i
q 2
1
2
1
2
r mr ( θ ) = mr 0 cosr θ + mr −1,1 ,cosr −1 θ sin θ + 1 (2.177)
+ m0 , r sin r θ
using Equation 2.176. The second-order surface spectral moments m20, m11, and m 02, can be found from three second-order profile moments in arbitrary directions θ1, θ2, θ3, Thus
m20 m2 (θ1 ) m11 = M −1 m2 (θ2 ) m02 m2 (θ3 )
(2.178)
where
cos 2 θ1 M = cos 2 θ2 cos 2 θ3
2 sin θ1 cos θ1 2 sin θ2 cos θ2 2 sin θ3 cos θ3
sin 2 θ1 sin 2 θ2 (2.179) sin 2 θ3
If θ1 = 0°, θ2 = 45°, θ3 = 90°, Equation 2.178 reduces to
m11 = m2 (45) − 12 m2 (0) − 12 m2 (90)
(2.180)
m02 = m2 (990). Thus, if m20 is the variance of the slope in the zero direction, m 02 is the variance of the slope in the 90° direction then m11 is the covariance of the slopes in those two directions. It should be noted that the angles 0°, 45°, and 90° were chosen for convenience only; however, Equation 2.178 may be used with any three angles. Again employing Equation 2.177, the fourth-order surface spectral moments m40, m31, m22, m13, and m04, can be
(2.181)
where
cos 4 θ1 cos4 θ2 M = cos4 θ3 cos 4 θ 4 cos4 θ5
4 sin θ1 cos3 θ1 4 sin θ2 cos3 θ2 4 sin θ3 cos3 θ3 4 sin θ4 cos3 θ4 4 sin θ5 cos3 θ5
6 cos2 θ1 sin 3 θ1 6 cos2 θ2 sin 3 θ2 6 cos2 θ3 sin 3 θ3 6 cos2 θ4 sin 3 θ 4 6 cos 2 θ5 sin 3 θ5
4 cos θ1 sin3 θ1 4 coss θ2 sin 3 θ2 4 cos θ3 sin3 θ3 4 cos θ4 sin3 θ4 4 cos θ5 sin 3 θ5
sin 4 θ1 sin 4 θ2 sin 4 θ3 sin 4 θ4 sin 4 θ5
(2.182) The values of m 40 and m 04 are the variances of the curvature in two perpendicular directions, and m22 is the covariance between these two curvatures. The values of m31 and m13 are the weighted covariances between the curvatures in two perpendicular directions defined as follows: d 2 z 3 / 2 d 2 z 1/ 2 m31 = E 2 2 dx dy
d 2z m13 = E 2 dx
1/ 2
d 2z dy 2
3/ 2
(2.183)
.
These expressions are considerably simplified when the surface is assumed to be isotropic, which implies that the stochastic properties of the surface in general and mr(θ) in particular are independent. Under this assumption, the surface and profile spectral moments are related by
m20 = m2 (0)
m40 m4 (θ1 ) m31 m4 (θ2 ) −1 m22 = M m4 (θ3 ) m m (θ ) 13 4 4 m04 m4 (θ5 )
(2.176)
and can be found by relating them to profile moments mr(θ) at angle θ:
calculated from five fourth-order profile spectral moments in arbitrary directions θ1, θ2, θ3, θ4, and θ5. These are
m00 = m0 m20 = m02 = m2 m11 = 0 m40 = m04 = 3m22 = m4 m31 = m13 .
(2.184)
Therefore, for this case the desired characteristics can be obtained from a single profile. It can be shown, for instance, that using this nomenclature and with the associated constraints, that the density of summits is given by
Dsum =
1 m4 . 6 π 3 m2
(2.185)
The parameter α is similar to the Q factor of the power spectral density. Large α implies a wide spectrum. For α→1.5 the spectrum becomes narrow. Letting z′ = z/σ (normalized height)
62
Handbook of Surface and Nanometrology, Second Edition
for α → 1.5 psum′ (z ′) :
Ppeak ( z ′)
=
{
2 3 z ′2 2 − [ z ′ − 1 + exp(− z ′ 2 )] for z ′ ≥ 0 2π 2
for α → ∞: psum ( z ′) =
=
1 exp ( − 12 z ′ 2 ) for z ′ < 0 (2.186) 2π
which imply that for wideband surfaces the summit distribution is indeed Gaussian, whereas it is not for narrowband surfaces where it becomes more nearly Rayleigh or Maxwellian. Similarly the expected value of the mean curvature for summits of height z′, (not slope) expressed in a normalized form by dividing by √m 4, is p(sum. curv. at z ′) m4
p(sum. curv. at z ′) = 2 / 3zz ′ , z ′ ≥ 0 for α → 1.5 (2.187) m4 = (8 / 3 ) ⋅ π
m0 m4 density of extreme = density of zeros m22
(2.188)
thereby showing that α is in fact k2 which is obtained from the profile. Hence the α value can be found by a simple counting routine. Also, the density of peaks (or valleys) is as proposed earlier:
Dpeak =
1 m4 2 π m2
1/ 2
,
(2.189)
which can be compared with the density of summits
where α − 1 k1 = α
Dsum 1.2 ( Dpeak ) . 2
(2.190)
Note this is not the simple factor of (Dpeak)2 as one might expect. Similarly the peak and summit heights differ. This is due to the presence of saddles and cols in the areal case. The probability density ppeak (z′) is given by α = 10
(2.193)
where k3 = α/(2α–3) and k 4 = k3 (12/α)1/2, and t=
1 3 2 m4
1/ 2
d 2z + d 2z dx 2 dy 2
(2.194)
from which psum at the limiting values α = 1.5 can be found: z ′ exp(− z ′ 2 / 2) ppeak ( z ′) = 0 ppeak (z ′) =
1 exp(− z ′ 2 / 2) 2π
z′ > 0 α = 1.5 z′ > 0 α → ∞. (2.195)
A comparison of these distributions reveals that the profile shows far fewer higher peaks and more low peaks than actually exist. The discrepancy is greatest for α→1.5 and zero for α→ ∞ (Figure 2.74). The important point here is that tribologically important parameters can be found by means of the moments of the spectra. Whitehouse earlier approached this in a completely different way using the correlation function rather than the power spectrum and using discrete points from it rather than the continuous analysis of Nayak. Similar effects are revealed for curvatures etc. Practical verification of these results has been obtained previously by Williamson [55] by making use of relocation profilometry.
Summit Peak
Peak
2.0
z ′. (2.192)
× exp[ − 12 ( k3t 2 + k 2tz ′) ]
0.5
1.0 z
1/ 2
3k 3 exp(− k3 z ′ 2 )[ t 2 − 2 + 2 exp(−t 2 / 2) ] 2π
psum (z ′t ) =
Summit
FIGURE 2.74â•… Peak and summit distributions.
1 − k12 k2 = 2k12
and
α = 1.5
0.5
0
1/ 2
It has also been shown that the probability density for a summit is
2
α=
exp − z ′ 2 + π .k exp − z ′ 2 (1+ erfk ) , (2.191) 2 2 2 2 k12
for α → ∞
which indicates that for wideband surfaces the mean curvature varies linearly with peak height whereas for narrowband surfaces it is very nearly independent. Estimates of m2, m0â•›, and m4 can be obtained from the number of maxima, minima, and zeros on the profile (as the k value of profiles). It has been shown by Longuet-Higgins that
k1 2π
0
1.0 z
2.0
63
Characterization
He shows divergences of the same order. See also Sayles and Thomas [56]. The conclusion reached from LonguetHiggins’ and Nayak’s work is that the high-order statistics of the two-dimensional surface depends on the variances of the height, slope, and second differential, m 0, m2, m 4 which can be obtained from a single profile for Gaussian isotropic surfaces and from three non-parallel profiles for Gaussian non-isotropic surfaces. It should be noted that there are fundamental assumptions made in much of the preceding work, which are that the height distribution is random (i.e., Gaussian in nature) and also that asperities and valleys follow reasonably wellbehaved shapes. Unfortunately neither has to be true for the surface roughness produced by many single-point and multiple-point cutting processes such as milling; the amplitude distribution is anything but random so that the results obtained above would hardly be applicable. Similarly the asperities are often not simple peaks; the very nature of cutting, especially with a blunt edge tool or grit, produces a wave-like effect which introduces overhang and re-entrant features into the geometry and gives multivalued z values for x and y—not at all easy to deal with mathematically. (Incidentally, the latter factor is also true for sea waves, a factor which limits the usefulness of Longuet-Higgin’s approach to a relatively calm sea.) Other models have been used, some of which presume on the nature of the waviness present. For example, the work of Lukyanov [57] makes the assumption that the roughness is random and the waviness is not. Thus
z ( x , y) = h( x , y) + w( x , y).
(2.196)
This approach will be considered under waviness. 2.2.2.4.2 Practical Approach to Areal (3D) Measurement Much of the previous work on areal assessment has been of a theoretical nature and has been based on the work of Longuet-Higgins [41] transposed from Oceanography by Nayak [43]. This work, coupled with the inability to map surfaces quickly and with high fidelity, put off practicing engineers. Both of these problem areas are being eroded by the more pragmatic approach of Stout et al. [58], who, working with EC support have produced some plausible practical alternatives to the purely theoretical approach. It must be said that once the direct link with the theory has been broken the constraints imposed by rigor are lifted, allowing some useful “functional” parameters to be put forward. The justification for these new parameters is powerful; they fit in better with practical engineering. A summary of these and similar parameters is given below. One good idea in the development of a new parameter was to change the letter prefixing profile parameters from R to S indicating “surface” parameters although it has been used for “stressed” surfaces. This is not an international standard but it is a step forward in itself. There should be no ambiguity between the “surface” and profile parameters. The
abbreviations used below have not been adopted formally but, as they are straightforward, they are used here. The primary parameter set is split into four groupings of parameters: amplitude parameters, spatial parameters, hybrid parameters and functional parameters. Missing from the 17 parameters listed above is the symbol Sa representing the surface average. It would probably be sensible to include it because it does represent the most tangible link with the part. However, the original reasons for using Ra, namely that it could be checked from the profile chart whereas the RMS value could not, simply no longer applies because of the digital takeover. It certainly makes no sense to put both in—there are more than enough parameters anyway. The amplitude parameters follow the profile definitions but the areal ones do not necessarily. Some specific areal parameters result from the nature information, lay and isotropy can now be included. Sae, the length of the shortest autocorrelation function, is one such parameter following on from the proposal of Kubo [54]. The hybrid parameters again follow on from the profile equivalent. The functional parameters listed below use the definitions proposed by Stout [58]. They are basically an extension of the automotive parameters Rkv, Rk, Rks used for describing the shape of the material ratio curve. In the first instance these were obtained from the profile but in the “surface” material ratio Sdr they better describe what is taking place when the surface is being used. These surface parameters are provisionally listed in EUR 15178EN Surface Bearing Index. Sbi is given by
Sbi =
S0 1 = . z 0.05 h0.05
(2.197)
In Equation 2.197 z0.05 is the height of the surface at a height of 5% bearing (material) ratio. A large value of Sbi indicates good load carrying capability and would indicate a good bearing. For a Gaussian surface Sbi is about 0.6 and for a range of surfaces, including multi-process finishes such as plateau honing, the value is between 0.3 and 2 which is a useful range. A run-in surface tends to have a larger value than an unworn surface so the Sbi parameter could be used as a measure of wear. The primary parameter set is split into four groupings of parameters: amplitude parameters, spatial parameters, hybrid parameters, and functional parameters. Surface material ratio Sbc
Sbc =
S0 z 0.05
(2.198)
where z0.05 is the height of the surface at 5% material ratio. Core fluid retention index Sci
Sci = ( v(0.05) − vv (0.08)) /Sq (unit area )
(2.199)
where v represents valley. If Sci is large it indicates that the surface has good fluid retention properties.
64
Handbook of Surface and Nanometrology, Second Edition
The range is
0 < Ssi < 0.95 − ( h0.05 − h0.08 )
(2.200)
when h is z normalized by Sq. Valley fluid retention index Svi Here
Svi = ( vv (h = 0.8)) /Sq ( unit area )
(2.201)
0 < Svi < 0.2 − (h0.8 − h0.05 )
(2.202)
For a Gaussian surface Svi is about 0.1 in value. The values 0.05, 0.8, etc., are arbitrary but accepted as reasonable. The use of functional parameters is not new. As early as 1936 Dr. Abbott proposed what is now the material ratio curve as a parameter useful for load carrying. There is nothing wrong with functional parameters except for the fact that they are matched to specific applications and can give misleading values for unrelated functions. Mixtures of functional parameters could be used to describe different applications but then the parameter rash could well be the outcome. Another problem is that the functional parameters mentioned above have been designed for multi-process finishes. However, the real gains to be made by measuring over an area are in predicting or modeling the path of the tool and not fine tuning the roughness. This is what is missing from today’s list€of parameters—all 17 of them according to Table 2.10. Using parameters such as Sae gives very little useful information about the “lay” especially in multi-tool processes such TABLE 2.10 Primary Set of 3D Surface Roughness Parameters Sq Sz Ssk Sku
Amplitude Parameters Root-mean square deviation of the surface (µm) Ten point height of the surface (µm) Skewness of the surface Kurtosis of the surface
Sds Str Sal Std
Spatial Parameters Density of summits of the surface (mm−2) Texture aspect ratio of the surface Fastest decay autocorrelation length (mm) Texture direction of the surface (deg)
SΔ Sdr Ssc
Root-mean square slope of the surface (µm/µm) Arithmetic mean summit curvature (µm−1) Developed surface area ratio (%)
Hybrid Parameters
Functional Parameters Characterizing Bearing and Oil Retention Properties Surface bearing index Sbi Sci Core oil retention index Valley oil retention index Svi Sm Material volume (µm3/mm2) Sc Core valley volume (µm3/mm2) Sv Deep valley volume (µm3/mm2)
as face milling. It could be argued that using a very general parameter to estimate a very specific lay pattern is questionable. The ironic part of this exercise is that the most important information (for example the tool path) in milling is completely ignored at the measurement stage only to be replaced by an almost irrelevant correlation procedure. Undermining all the attempts to classify the areal properties of surfaces is the fact that the actual “system,” of which the surface is only a part, is neglected. The “system” is comprised of at least two surfaces making contact at perhaps part of a bearing. The way these interact is of prime importance. One reason why the “systems” approach is neglected is because the function of the system is difficult to achieve. Short of carrying out the function with real parts, which is impractical, the possibilities are to simulate the mechanics of the system in a computer given the measured data from both surfaces or to analyze the system theoretically. The latter is acceptable providing that the assumptions made are realistic. The message is that it is pointless having 14 or 17 or 23 parameters for one or even both surfaces unless the interaction mechanism is itself characterized. At present, at best, the average distance between the mating surfaces is known and possibly any tilt. Usually even these factors are not known together with roundness error, cylindricity, etc. It seems inconceivable that most of the major systems parameters are neglected, yet more and more detail is sought for individual surfaces. The one redeeming factor is that Stout [58] has moved away from the theoretical parameters (found in communication theory and applied to surfaces) in favor of “functional” parameters which should be at least partially relevant. 2.2.2.4.3â•… Nature of Areal Definitions Description of areal properties corresponding to say a peak or valley and in particular dominant cases [60]. One of the first attempts to describe a surface in terms of hills and valleys was made by Maxwell [61]. According to him, a hill is an area from which maximum uphill paths lead to one particular peak and a dale is one in which maximum downhill paths lead to one particular dale. Also boundaries between hills are water courses and between dales watersheds; course line and ridge lines, respectively. Both ridge and course lines emanate from saddle points and terminate at peaks and valleys. Scott extends the ridge and course concepts to major hills and valleys [60], i.e., “a hill is a single dominant peak surrounded by a ring of course lines connecting pits and saddle points, and a dale is a single dominant valley surrounded by a ring of ridge lines connecting peaks and saddle points”(Figure 2.75). This “motif” method has some merit because functions such as mechanical seal and flow in general depend for their efficiency on a knowledge of the probability of escape routes. Pathways between peaks and valleys in the areal model can provide one way to estimate the flow of liquid within the zone. In the case where contact has been made, as in a seal, it may be a relevant parameter (Figure 2.76).
65
Characterization
P1
P2
S1
V1
S3
S4
P4
V2
S5
P3
S2
S7
S6
P6
P5 V3 S8
FIGURE 2.75â•… Contour map showing critical lines and points: peaks P, pits V, saddles S. (After Scott, P. J., Areal topological characterization of a functional description of surfaces. European Surface Workshop. France et Silette, June, 1998.) Height
Height
P4
10
10 8
S7
P6 S4
6
8
P3
S2
S3 4
6
P2
P1 P5 4
S1
V1
S8
2
0
S5 V0
0
–4
V3
S5 V0
–2
–2 –4
V1
2
S6 S8
S3
V2
FIGURE 2.76â•… Full change tree. (After Scott, P. J., Areal topological characterization of a functional description of surfaces. European Surface Workshop. France et Silette, June, 1998.)
The pathway from summit to dale is shown in Figure 2.77. This is called a “change tree.” Clearly the tree can be made for hills and vales and for the typical joint situation (Figure 2.78). The critical paths drawn on the contours of a surface together with the hills and vales trees give an idea of the way that flow of liquid or air passes across the surface. Rather than just saying that there must be leakage between two surfaces in, say, a mechanical seal it could be possible using this methodology to determine the actual pathway.
V3
V2
FIGURE 2.77â•… Dale change tree (After Scott, P. J., Areal topological characterization of a functional description of surfaces. European Surface Workshop. France et Silette, June, 1998.)
2.2.2.5â•…Discrete Characterization 2.2.2.5.1â•… General Method: Whitehouse Whitehouse based a typology on what was measured, that is the actual ordinates of the surface itself. Thus instead of using joint probability distributions p(z, m, c) involving surface height z, slope m and curvature c, all taken as random variables, he used the joint probability distributions p(z1, z2, z3, z4.,...) of measurements of the surface: his motivation being that these ordinates were what were directly measured and not parameters derived from them! These were used to examine the average joint behavior of the measurements using the multinormal
66
Handbook of Surface and Nanometrology, Second Edition
distribution in such a way as to predict functionally important€properties or manufacturing process properties. This completely different way of using the multinormal distribution was tackled by considering the average behavior of discrete ordinates of the surface rather than the continuous variables used by Nayak. This involved discrete values of the autocorrelation function rather than moments of the continuous power spectrum (Figure 2.79a). In a series of papers from 1969, he and co-workers [44, 62–64] developed a characterization of profiles and areal (or 3D) surfaces totally in terms of discrete values of the autocorrelation function of the profile and areal coverage of the surface (Figure 2.79b).
A summary of the way in which this typology of surfaces can be used will be given here. The theory is demonstrated in Chapter 3, where exactly the same procedure can be used to explain digital measurement results. This is the innovation. It formally relates the characterization of the surface to the measurement possibilities. One important note is that, whereas the results for the discrete autocorrelation function of a profile converge to that of Nayak’s profile as the spacing (h) between correlation points is taken to zero, the discrete areal results do not converge to the continuous areal results. The results for profiles by Whitehouse and Nayak have been compared experimentally and theoretically by Bhushant [65]. Also a characterization by Greenwood [66] will be given. This latter treatment is an attempt to simplify and clarify the Whitehouse results. All the methods of Nayak, Whitehouse and Greenwood rely on the multinormal distribution as a basis for the calculations. It has been found that a certain amount of non-Gaussian behavior can be tolerated. It has been suggested by Staufert [67] that a skew value of up to +¯1 still allows good results. The Whitehouse parameters for a profile are given in terms of the profile correlation function at the origin R2q and at positions h and 2h from the origin, that is A(h) and A(2h) called here ρ1 and ρ2. Thus the mean peak height is
Height
P4
10 8
S7
P6
P3
S4 6
S2
P2
P1 P5 S1
4
1/ 2
1 − ρ1 Rq π 1/ 2 (3 − 4ρ1 + ρ2 2 1/π tan −1 (1 − ρ2 )
S6 2
0
(2.203)
Hence, the density of peaks is –2
Dp = –4
1 (3 − 4ρ1 + ρ2 tan −1 πh (1 − ρ2
1/ 2
n0 =
(a)
1 cos−1 ρ1 πh
(b)
ρ(0)
ρ2
ρ1
ρ
ρ(h)
4
ρ3
ρ5 ρ8
ρ(2h)
h
2h
A 1 tan −1 3 πh A2
1/ 2
(2.204)
the density of zero crossings is
FIGURE 2.78â•… Hill change tree. Shows how the pathway connects from summit to dale. (After Scott, P. J., Areal topological characterization of a functional description of surfaces. European Surface Workshop. France et Silette, June, 1998; Scott, P., Private Communication (Rank Organisation, 1980)).
0
=
τ
Rectangular grid of ordinates
FIGURE 2.79â•… (a) Three-point autocorrelation function, (b) areal correlation coefficient positions.
ρ7
ρ6
(2.205)
67
Characterization
mean slope is
m=
Rq 1 − ρ2 h π
1/ 2
=
Rq A2 h π
and for the discrete tetragonal model for the limiting case when h→0
1/ 2
(2.206)
Dds =
the variance of peak heights is
1 + ( Rq2{[( A1 2 πD p )( A2 A3 )1/ 2 − ( A1 4 πD p2 )]}
(2.207)
( Rq2 A3 ) /[2 D ph 2 ( πA)]1/ 2
(2.208)
the variance of curvatures is σ c2 = [( Rq2 A3 ) /[4 h 4 πA1 ])(8 πA1)
+ (2h /D p)( A3 A2 )1/ 2 − ( A3h 2 /D p2 )]
(2.209)
and the correlation between curvature and peak height is
correlation = [1 − (1 − 2ρ12 + ρ2 ) / ( A3σ 2p )]1/ 2 (2.210)
where A1 = 1 – ρ1, A2 = (1 – ρ2), A3 = (3 – 4ρ1 + ρ2) and σ2p is the peak variance normalized with respect to σ2, i.e., Rq2. This set of parameters derived from three points on the correlation can always be augmented by using more than three points, say five or seven. As it stands this model permits a best spectral fit of the form P(ω) P(ω ) − 1/[( jω )2 + jω (ρ12 − ρ2 ) / (1 − ρ12 )
+ ρ1 (ρ2 − 1) / (1 − ρ12 )]2
(2.211)
of which the exponential is a special case. Fitting four or more points to the autocorrelation function allows secondorder spectra to be modeled and higher degrees of freedom. This has been found to be largely unnecessary. In extending this to areal (or 3D) surfaces a number of options arise depending on how the area is sampled. The comparison of the behavior of surface properties between continuous and discrete models is not straightforward. This is because of the options available in the discrete definition. Here, the straightforward tetragonal pattern of sampling will be used in which a summit is defined if it is larger than four orthogonal adjacent points as in Figure 3.21c. Digonal, trigonal, and hexagonal patterns will be considered in addition to this in Chapter 3 on digital processing. The problem is that none of the patterns is wrong or right; they are just different. This difference matters because it is not just what is characterized here as a discrete model, it is actually what everybody measures. This discrete modeling provides the link between the theory and the actual experiments. As an example of how the continuous method differs from the discrete, consider the density of summits. For the continuous case given by Nayak
Dsum = (6 π 3 )−1 ( D4 / − D2 )
= 3
π + 2 sin −1 (1/ 3) + 4 2 Dsum 4π
(2.213)
= 1.306 Dsum .
the mean curvature of peaks is
π + 2 sin −1 (1/ 3) + 4 2 D4 2 h D2 4π2
(2.212)
Hence the discrete summit density is 30% larger than the continuous. This is because the discrete model identifies what it thinks are summits but which turn out not to be! This is easily possible because any discrete model cannot include all the possibilities of exclusion from the summit definition in the analogue case. Taking this further, the argument would maintain that the fewer the number of points making up the definition, the higher the density would appear to be. Indeed, for trigonal models in which three adjacent points to a central one are considered, the density is 73% higher. In Equation 2.175 D2 and D4 are the second and fourth differentials of the autocorrelation function at the origin, that is A0(0) and Aiv(0): and
η = − D2 ( D4 )−1/ 2 −
A′′(0) Aiv (0)
(2.214)
which is the correlation between the height and curvature for a random waveform. For summit height the continuous summit mean height is
E[ z|continuous|] =
4 η. π
(2.215)
For tetragonal characterization, which is the standard pattern used by most researchers, E[z|discrete] is given by E ( z|discrete|) =
8 2π η π + 2 sin –1 (1 / 3) + 4 2
4 = (0.938) η π
(2.216)
= 0.938 × E[z|continuous|]. The mean summit height is lower by 6%. These disturbing differences are taken further in the next chapter but the point here is that, even if it is agreed that correlation (or spectral) methods form the basis of a good model for the characterization of the surface, much has to be agreed between researchers either before they will agree with each other’s results on the same surface or on whether they ever get to the “true” value of the surface even if it were possible. The problem has been masked by dealing mainly with profiles. Discrete (measured) values of the profile will gratifyingly converge to the theoretical case as the sampling gets higher. But in the areal case they never do! The difference is dependent on the coverage of the discrete model.
68
Handbook of Surface and Nanometrology, Second Edition
2.2.2.5.2 Alternative Discrete Method: Greenwood In an effort to clarify the situation Greenwood [66] reworked the discrete results of Whitehouse and changed the nomenclature to simplify the results. For example, the probability of an ordinate being a peak in Greenwood’s theory becomes
numerical analysis values. Whitehouse accepts from the start the overall dependence on discrete values and establishes the method of characterization completely on it; the characterization formulae and the numerical analysis formulae are made to coincide: this ties the theory with what is actually being tried to be measured. In these methods of characterizing surfaces there is almost universal acceptance of the fact that the ratio of zero crossings (or mean line intersections) and the peak density is a useful surface characterization parameter involving, in its various guises, α, r, and k. The important result is that there are no intrinsic parameters for the surface. No surface has a mean summit height of z ; it only has a mean summit height z for a given numerical model f(z) and sample interval h. Providing that f(z) and h accompany z when results are compared (and assuming that there are no instrumental problems) this is acceptable. To conclude this section, it has been shown that in any practical situation it is necessary to characterize the surface and the procedure if results are to be compared. Another point which this section on surface roughness shows is the enormous difference in complexity which the manufacturing engineer requires to specify the surface as compared with that of the tribologist. The former requirement is straightforward—simple averages like Ra can be used— whereas in the latter much more complicated parameters are required. Finally, these methods of specifying the characteristics of surfaces have resulted in methods involving average values, which allow the probability of extreme values such as peaks to be estimated. This does not solve the problem of specifying freak behavior (even if the freak can be found). Neither does it get much closer to solving the question of what surfaces are really like. At best the properties within very closely defined limits can be specified, although even with fractal-type surfaces (discussed later in Section 2.2.4.4 and Chapter 7) this is difficult.
N=
θ where θ = sin −1 ( hσ k / 2σ m ) π
(2.217)
1 (3 − 4ρ1 + ρ2 )1/ 2 tan −1 π (1 − ρ2 )
(2.218)
instead of
N=
where σk and σm are the standard deviations of curvature and slope, respectively; u becomes one of the characterizing parameters (actually dependent on h). Similar expressions corresponding to Equation 2.203 through Equation 2.209 are found. Thus the mean peak curvature (expressed as a ratio to σk) is
1 π sin θ /θ 2
(2.219)
and the variance of peak curvature (again expressed to σ2k, the variance of curvature) is
1 + (sin 2θ / 2θ) −
π (sin θ /θ)2 . 2
(2.220)
The other parameter Greenwood uses to characterize the surface he calls r, where r is given by
r = (σ 2m /σ )σ k
(2.221)
where
r −2 = α =
m0 m4 m22
(2.222)
This r represents the “surface roughness character.” Between the r and u, Greenwood goes on to establish summit properties using a third parameter
τ = 2(1 − 2ρ1 + ρ 2 ) / (3 − 4ρ1 + ρ2 )
(2.223)
For a good comparison of the Nayak, Whitehouse and Greenwood models the reader should consult the paper by Greenwood. The two methods of Whitehouse and Greenwood are merely different ways of tackling the discrete problem. The Nayak model for the surface is continuous, the Whitehouse model is discrete and the Greenwood model attempts to provide a link between the two. It should be remembered, however, that although Greenwood’s characterization provides simpler formulae, the parameters σk and σm are still determined by discrete methods which use the Lagrangian
2.2.2.6 Assessment of Isotropy and Lay The characterization of the lay of surfaces has been sadly neglected, mainly because of its complexity. An elementary classification is shown in Figure 2.64. Isotropy is usually taken to mean the lay of random-type surfaces, thereby differentiating between grinding on the one hand and, say, shot blasting on the other. General lay takes all surfaces into account. It cannot, however, be ignored in very many functional situations, especially relating to bearings, mechanical seals and cylinder walls; it can be more important than the value of the roughness. The reason, as Wirtz [68] pointed out, is due to the large variety of motions of the machine tool in generating the surface. Simply using the lay as a means of typology or characterization is not enough. One method suggested by Peklenik and Kubo depends on characterizing the plots of the variations in the correlation functions on a linear or polar scale. This method is convincing but difficult to do because of the need to map the surface
69
Characterization
in some detail. An alternative method is to use the “long crestedness” criterion of Longuet-Higgins. This type of surface approximates to a series of parallel grooves. The definition that relates to that of Peklenik and Kubo requires taking profile graphs in different directions and estimating some feature of the plot (Figure 2.56). In Longuet-Higgins’ case the following long crestedness (LC) criterion has been defined [41] as 1/ 2
LC =
2 2 m20 + m02 + ( m20 − m02 ) + 4 m11
1/ 2
2 m20 + m02 − ( m20 − m02 ) − 4 m11 2
. (2.224)
For a completely isotropic surface LC = 1; for a completely long crested wave (m2)min = 0 and LC → ∞. If (m2)min is made equal to 0, m11 is equal to (m 02 m20)1/2, remembering that the m 02 and m20 moments would have been taken at right angles. An excellent account of this type of approach is given by Pandit et al. [69]. This will be referred to in Section 2.2.4.1. Although this method of quantifying isotropy is sensible for truly random surfaces, it runs into severe problems for other kinds of surface. Take for example a face-turned part. Such a criterion would produce an isotropic result only if the measured tracks started at the center of the face; anywhere else as a starting point would give a different result. From the measurement point of view the surface is neither random nor stationary. One could argue that this technique should only be used for random surfaces. The problem here, however, is that it is never possible to be sure whether deterministic elements are present. This criticism applies equally to the correlation plotting methods proposed by Peklenik and Kubo. A technique for describing isotropy was also tried by Ledocq [70] who made a succession of traces in radial directions on various machined surfaces (similar to the work of Peklenik and Kubo). He then plotted the variations of wellknown parameters such as Ra and Rq, the average wavelength and the 0.5 correlation length. Unfortunately, although results were obtained they proved to be inconclusive, not least because of the instrumental difficulty of measuring texture along the lay—the problem is that of knowing what, if anything, to do with the sampling length for different directions! What is needed is a technique which deals with any surface and preferably gives a numerical value to the isotropy and lay. One sensible approach has been proposed by Wirtz [68] who suggested that it should be possible to relate the lay to a number of basic geometrical features such as circles, lines, etc. (Figure 2.80). In principle, this technique would derive from the appearance of the surface the movements of the tool which generated it. This, after all, is the lay. There is, however, still the problem of quantifying it. It seems that this type of method as it stands has potential but not yet the capability because of the difficulty of measurement. Probably the best method up to now is to use a two-dimensional spectrum method of a scaled-down model of the surface using “liquid gates.” This enables an areal diffraction pattern to be produced which reveals the lay.
Radius fixed, moving generator
Generator fixed, moving radius
FIGURE 2.80â•… Typical patterns of machined parts produced with single tool.
Perhaps the only method is that used at present following drawing practice. In this method the pattern is identified by reference to standard patterns in a way which is similar to the use of metallurgical atlases. In these, photographs of metals under different conditions are compared by eye. There is, however, no reason why the comparison cannot now be done by a pattern recognition method by computer. There are many techniques for recognizing patterns. Many such patterns have been presented in early work in the French standards for surfaces and in British standards (Figure 2.81). A much more comprehensive approach has been suggested along these lines [71] which characterizes the lay along set theory lines into patterns comprising points, straight lines, circles (including secants), polygons, and curves. Up to 17 different groupings have been observed, each group having two subset groupings. In all, hundreds of different observed patterns can be classified in this way. However, the complexity of the system probably makes the application of this method prohibitive. This technique, as in the Wirtz methods, is basically a pattern recognition technique and so, in principle, with the massive advances in this subject since the appearance of vision systems for robots, could be tried again. Also, since the work on fractals is essentially a description of form and structure [72], it is likely that there is scope for a proper visual classification system. The work on areal assessment is basically on two levels: one is visualization and the other is quantification. The point to be made here is that the use of simple visualization is not to be ignored because, as pointed out by Stout [58], a great deal of information, particularly about structure, is available from a surface map. Use of suitable software can enable the eye to see many different aspects of the surface which would normally be lost. Stout lists a few suitable operations which can be carried out on a 3D map to help the operator [58]. These are:
1. Inversion by turning the picture upside down 2. Magnification in any direction 3. Truncation of the signal at any level of height 4. Contouring
70
Handbook of Surface and Nanometrology, Second Edition
Interpretation
Symbol
=
= Parallel to the plane of projection of the view in which the symbol is used
⊥
⊥
Perpendicular to the plane of projection of the view in which the symbol is used
X
Crossed in two slant directions relative to the plane of projection of the view in which the symbol is used
M
Direction of lay
Direction of lay X
Direction of lay M
Multi-directional
C
C
Approximately circular relative to the center of the surface to which the symbol is applied
R
Approximately radial relative to the center of the surface to which the symbol is applied
R
FIGURE 2.81â•… A classification of lay which appears on engineering drawings.
One of the very few pieces of work which directly addresses lay measurement of non-random surfaces is by Boudrean and Raja [73]. The technique is quite simple: it makes use of the fact that two closely spaced parallel profiles will appear to be shifted whenever the dominant lay direction is not perpendicular to the profile direction. Boudrean and Raja utilize the cross-correlation function to measure these shifts and then simple linear models are applied to the shifts to quantify the lay characteristics. This contribution was interesting in the sense that it could cater for lay which was curved as well as straight. The only problem in the case of curved lay is that the shift between profiles depends on the position of the traces within the data map (Figure 2.82). From the information obtained by this method useful data concerning the manufacturing process could be obtained after considerable interpretation. This work certainly reinforced the view that all data on the surface of a workpiece is useful for something. So far this chapter has virtually followed a chronological path. This development has been intentional because it
keeps firmly in mind the problems that arose in the early days and the methods used to solve them. Although the techniques are much more powerful today new problems keep emerging. The interesting point is that the old problems keep �re-emerging as new processes are introduced or new functions demanded. A discussion of isotropy and lay always highlights one of the perennial problems of surface characterization which is that of directionality: how does the lay relate to the direction of motion of the surface in use. This factor in tribology overrides practically all characterization issues and yet is almost always ignored for the simple reason that functional considerations are not included: a point brought out using the function map concept in Chapter 7. Many of the newer methods such as discrete analysis and random process analysis are now incorporated into instruments. However, there is a continual search for newer, perhaps better, parameters. In what follows a few of the alternative parameters will be revealed. Although these have been demonstrated in various research papers they cannot be said
71
Characterization
∆1
∆1
∆2 = 0 ∆2 = ∆1
∆1 ≠ ∆2
FIGURE 2.82 Raja lay topology. (Reprinted after Boudrean, B. D. and Raja, J., Int. J. Mech. Tool. Manu., 32, 171, 1992. © 1992, with permission from Elsevier.)
to have gained universal acceptance. This may or may not come. Nevertheless, it is useful to mention them because they point the way to possible developments in the future.
These attempts showed two things: one was that the existing parameters were insufficient to characterize the surface; the other was that it was not very clear which way to go forward!
2.2.3 Methods of Characterization Using Amplitude Information
2.2.3.2 Skew and Kurtosis More recently a more statistical method was suggested by Peklenik to Al-Salihi [39] who then included the skew and kurtosis values together with the Ra or Rq values as a complete set of characters. The two extra moments were an attempt to quantify the shape of the amplitude density curve. For many surfaces this technique was an acceptable step forward. However, problems can occur because the two parameters are not independent. An alternative method was proposed by Whitehouse [74]. His idea was to try to devise parameters which weighted peaks differently to valleys, thereby introducing a variable which could be useful in predicting function. The proposal was to use the beta function as a means of characterizing the amplitude density curve.
2.2.3.1 Amplitude and Hybrid Parameters The route taken so far—that of considering the profile parameters which are in use today, progressing to random process analysis and from this to the areal evaluation of surfaces proposed by Longuet-Higgins, Nayak and Whitehouse—is taken as the general direction of progress in surface characterization. However, there have been many other attempts to classify the surface roughness which can be considered to be interesting and even valuable in some applications. Some of these are briefly considered to show the general way in which the subject is developing. Many simple classification systems for a typology of surfaces have been based either on the amplitude characteristics alone or on the spacings of profiles. A notable exception in the early days was Myres [14] who used four parameters, Rq, Δq, RMS curvature, and the directionality described in Equation 2.11. His interest was mainly in the influence of surfaces on friction. Incidentally, he found that over a wide range of roughnesses Δq had a correlation of 0.85 with µ the frictional coefficient—a result which would be received with some scepticism today. There have been a number of attempts to classify the APDF [8]. The first were probably Pesante [9] and Ehrenreich [10] who used the slope of the bearing (material) ratio curve even earlier but did not point out explicitly the statistical significance. Other people tried various ratios of the Ra and Rq values taken from the material ratio curve, and Oonishi appears to have been the first to consider the combination of different processes on the same material ratio curve. He also tried to incorporate some ideas about including a peak count in addition to the height information, as did Reason [7].
2.2.3.3 Beta Function The beta function is one that is defined within a given range of 0 → 1 [55]. It is expressed in terms of two arguments, a and b. Thus β(a, b) is given by
β ( a, b ) =
1
∫z 0
a −1
b −1
(1 − z ) dz.
(2.225)
It can be expressed in terms of a probability density Pβ(a, b, z):
Pβ ( a, b, z ) =
1 b −1 z a−1 (1 − z ) β( a , b )
(2.226)
where β(a, b) is the normalizing factor to make Pβ a true density. The usual parameters of the distribution can be determined in terms of a and b. Thus, using gamma function identities,
72
z=
Handbook of Surface and Nanometrology, Second Edition
β ( a, b ) =
1 β( a , b )
1
Γ ( a) Γ ( b) and Γ ( a + 1) = aΓ (a) (2.227) Γ ( a + b)
∫ zz
a −1
0
(1 − y)b−1 dz =
β(a + 1, b) a = (2.228) β( a , b ) a+b
the variance is σ2 =
ab (a + b + 1)(a + b)2
(2.229)
the skew is Skβ =
2(b − a) a + b + 1 a + b − 2 ab
1/ 2
(2.230)
and the kurtosis is
Kβ =
6[(a − b)2 (a + b − 1) − ab(a + b + 2)] . (2.231) ab(a + b + 3)(a + b + 2)
The basic philosophy was that any practical amplitude distribution could be approximated by a beta function (Figure€ 2.83). Note that the function has two parameters, each independent of each other, and so could be used as a basis for a typology or characterization; a is the weighting allocated to ordinates of the profile measured from the lowest valley upwards and b is the weighting of the same profile as seen from the top of the profile and measured downwards. Peaks and valleys are therefore differently weighted. This could (a point evaluated later) provide useful functional discrimination. The problem arises of how to determine a and b from the profile. By changing the range in Equation 2.228 from 0 to 1 to Rp + Rv or Rt and replacing s, the standard deviation of the distribution, by Rq, the a and b parameters become
a=
Rv ( Rv Rp − Rq2 ) R p ( Rv R p − Rq2 ) b = . (2.232) Rt Rq2 Rt Rq2 a=b=5 a=b=3 a=b=2 a=b=1 a = b = 0.5 0
0.5
1.0
The fact that odd peaks or valleys are only raised to a unit power suggests extra stability over the skew and kurtosis characterization method. Nevertheless, the weakness of the technique is that good estimates of Rv and Rp have to be made, which is difficult, indicating once again the basic problem of measuring peaks and anything derived from them! As an example of how the technique works from manufactured surfaces, compare this typology with one based on the skew and kurtosis. This is shown in Figure 2.84a and b. The other problem associated with the beta function approach is that it cannot easily cope with multimode distributions as can be seen by reference to Figure 2.83. So, for simple periodic profiles, there is sometimes a problem. It has correctly been pointed out by Spedding [72, 75, 76] that the beta function is only one example of the class of Pearson distributions and that delving further into these classes points to a better and still more comprehensive classification system. It may also be said that other descriptions of distributions exist which utilize three parameters and so could, in principle, be used to improve this type of characterization. One such is the hypergeometric function. The problem then arises of having too many parameters. If three are needed for the shape of the distribution and one for the size or scale factor then already the situation exists where four parameters are needed to specify amplitude information alone. This would be difficult to implement or justify practically. Alternative methods of characterization of the amplitude density function have been tried by using different types of function other than the beta function. Examples of this have been the Chebyshev polynomial approximation and the Fourier characteristic function. 2.2.3.4â•… Fourier Characteristic Function An obvious choice is the characteristic function of the distribution. This is the Fourier transform of the amplitude distribution function where ω is usually replaced by ζ. Thus C (ζ) =
∫
∞
exp( jζz ) p( z )dz.
−∞
(2.233)
Because this is a continuous function an arbitrary choice of ζ would be needed upon which to build a typology. However, a method is possible based upon the first few coefficients of
3
3
2
2
1
1 0
0.5
1.0
a=5 b = 1.5 a=2 b=1 a=3 b = 1.5 a = 1.5 b=3 a = 1.5 b=5
FIGURE 2.83â•… The beta function (left) symmetrical and (right) asymmetrical case. (After Whitehouse D. J., CIRP Annals, 27, 491–497, 1978. With permission.)
73
Characterization
Kurtosis (not normalized)
(a)
10 Honing 8 Grinding 6 EDM Milling Turning
2.0
1.0
(b) 8 6
Skew
+1.0
Honing EDM
Grinding
a 4 Turning
Milling
2
2
6 b
10
FIGURE 2.84 Process Identification: (a) central moments and (b) beta function. (After Whitehouse D. J., CIRP Annals, 27, 491–497, 1978. With permission.)
the Fourier series of p(z) using the range R = Rt or Rz as the fundamental wavelength. Here a typology could be based on F(n), n = 0, 1, where F(n) is given by
F (n) =
∫
R
0
exp( jn 2πz /Rv )zdz
f ( A, B,C ) = A + B cos(2 πz /R) + C sin(2 πz /R).
By a similar technique to that used for the beta function A, B, and C can be found in terms of R, Rq, and Rv or Rp. Thus A = 1/R
B=
2π 2 R2 + Rv2 + Rq2 − RRv R3 6
C=
π R 1− 2 v R R
2.2.3.5 Chebychev Function and Log Normal Function Another possible type of function to use is the Chebychev function. This is not an arbitrary choice of function because serious attempts to analyze the profile itself into Chebychev rather than power spectral coefficients have been made recently. The method would involve identifying a curve p(T0, T1, T2) with the amplitude distribution of the profile p(z), where T0, T1, and T2 are Chebychev polynomial coefficients of the first kind and where p(T0, T1, T2) is given by
(2.235)
p(T0 , T1 , T2 ) = T0 + T1 z + T2 (2 z 2 − 1)
(2.236)
which for a range corresponding with ± R/2 gives the coefficients in terms of surface profile parameters as 2 Rp 13 60 Rq T0 = + + 1− 46 46 2 R 2 R
(2.234)
which means matching to the distribution an expression of the form f(A, B, C) where
At first sight this appears to have some advantages. One of these certainly is that there is a strong connection between this and power spectral analysis, which is often used for random process analysis and currently used in surface metrology analysis. Unfortunately, despite having three parameters available (two, if the first is regarded as trivial), the possible shapes that can be matched are much more limited than even the beta function. Also, the simple, deterministic types of profile have awkward values. For example, the sine wave has values of C = 0 and B = 0.822. Symmetry considerations of the distribution especially are not well dealt with by using the odd symmetry of the sinusoidal component. Another disadvantage is that the shape of the fitted distribution does not change as the coefficients B and C are changed in magnitude. This is not true for the beta function: as a and b get large the distribution becomes more “spiky,” a property which allows a little extra flexibility. Obviously the Fourier transform approach would be more suitable if more coefficients were used, but this is not allowable because of the practical difficulty of adopting any system which employs more than one or two parameters.
T1 =
R 2 1− p 3 2R
T2 =
2 2 Rp 1 45 Rq − . + 1 − R 3 46 2 R 2R
(2.237)
An interesting alternative to the beta function which appears certainly to be as good is due to Murthy et al. [77] who proposed a log normal distribution. Thus, if the profile ordinates are z(x), then v is ln(z). If the transformed variable v is distributed according to a Gaussian (normal) model then z has a log normal distribution which is often found in distributions of extreme values such as peak distributions.
74
Handbook of Surface and Nanometrology, Second Edition
This distribution is
1 z − µ2 p( z , µ , σ ) = exp − . zσ 2 π 2 σ 1
(2.238)
Classical theory gives
z = exp(µ + σ 2 / 2) σ 2 = exp(2µ + 2σ 2 ) − z 2
(2.239)
When the expression is referred to surface characteristics Rq, Rv, Rp as for the beta function, the arguments μ and σ−€become µ=
2 ( 2Rp ) 1 ln 2 2 2 ( 2 R p ) + ( Rq )
Rq2 + ( 2 R p )2 σ = ln . ( 2Rp )2
(2.240)
Plotting μ against σ for a number of processes gives much the same amount of discrimination as the beta function. Unfortunately omitted from the investigation is the Gaussian curve which is discussed in more detail in the section on multiparameters. Murthy et al. also consider a two-dimensional mapping of the material ratio curve [77]. Some current thinking, not entirely new, concludes that three basic parameters are needed for the height, one for scale and two for shape. It can, of course, be arranged that three parameters all have the dimensions of length and the ratios provide shape information. One such method separates the bearing curve into three parts: the peaks, the basic surface, and the valleys (Figure€ 2.88). This method, not yet standardized, seems to give good results for multiprocesses such as plateau honing but the construction necessary to identify the three regions of the curve is not suitable for periodic surfaces. It should be pointed out that this type of surface, which is split according to height regions as above, is often called a “stratified” surface. This word is used to indicate that each stratum of the surface is targeted at a given function, that is load capacity, oil retention, etc. 2.2.3.6â•…Variations on Material Ratio Curve╯+╯Evaluation Procedures One method for characterizing stratified surfaces uses the material ratio curve. This note is purely practical and should not be used as an alternative to the cumulative peak variants mentioned earlier. In par