III EUROPEAN CONFERENCE ON COMPUTATIONAL MECHANICS
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering: Book of Abstracts
Edited by
C. A. MOTA SOARES J. A. C. MARTINS H. C. RODRIGUES JORGE A. C. AMBRÓSIO C. A. B. PINA C. M. MOTA SOARES E. B. R. PEREIRA and
J. FOLGADO Instituto Superior Técnico, Lisbon, Portugal
A C.I.P. Catalogue record for this book is available from the Library of Congress.
ISBN-10 1-4020-4994-3 (HB) ISBN-13 978-1-4020-4994-1 (HB)
Published by Springer, P.O. Box 17, 3300 AA Dordrecht, The Netherlands. www.springer.com
Printed on acid-free paper
All Rights Reserved © 2006 Springer No part of this work may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, microfilming, recording or otherwise, without written permission from the Publisher, with the exception of any material supplied specifically for the purpose of being entered and executed on a computer system, for exclusive use by the purchaser of the work. Printed in the Netherlands.
Table of Contents Preface Plenary Lectures M. Bendsoe Computational Challenges for Multi-Physics Topology Optimization ...................1 J.A. Cottrell, A. Reali, Y. Bazilev, T.J.R. Hughes Computational Geometry and the Analysis of Solids and Structures......................2 E. Oñate, S.R. Idelsohn, M.A. Celigueta, R. Rossi Advances in the Particle Finite Element Method for Fluid-Structure Interaction Problems................................................................................................3 W. Schiehlen, R. Seifried Elastic and Plastic Impacts in Multibody Dynamics ...............................................4 A. Suleman, P. Moniz Active Aeroelastic Aircraft Structures.....................................................................5 Keynote Lectures O. Allix Multiscale Strategy for Solving Industrial Problem ................................................6 F. Armero, C. Zambrana Numerical Integration of the Nonlinear Dynamics of Elastoplastic Solids .............7 T. Belytschko, S. Wang Computational Methods for Dynamic Crack Propagation.......................................8 P. Bergan, K. Bakken, K.C. Thienel Analysis and Design of Sandwich Structures Made of Steel and Lightweight Concrete ..................................................................................................................9 R. Borja Multiscale Modeling of Pore Collapse Instability in High-Porosity Solids...........10 R. de Borst, M.A. Abellan, J. Réthoré Instabilities and Discontinuities in Two-Phase Media ..........................................11 C. Bottaso Towards Maneuvering Aeroelasticity - Progress in the Simulation of Large Fluid-Structure Interaction Problems......................................................12 v
vi
Table of Contents
K. K. Choi, L. Du A Design Optimization Formulation for Problems with Random and Fuzzy Input Variables Using Performance Measure Approach ............................13 I. Doltsinis Strength of Porous Ceramics - Mechanical Testing and Numerical Modelling ....14 E. A. Dowel, K.C. Hall, J.P. Thomas, R.E. Kielb,M.A. Spiker, C.M. Denegri, Jr. Reduced Order Models in Unsteady Aerodynamic Models, Aeroelasticity and Molecular Dynamics.......................................................................................15 G. S. Dulikravich, H.R.B. Orlande, B.H. Dennis Inverse Engineering...............................................................................................16 J. Fish, W. Chen Multiscale Approaches for Bridging Discrete and Continuum Scales ..................17 P. L. George Adapative Mesh Generation in 3 Dimensions by Means of a Delaunay Based Method - Applications to Mechanical Problems.........................................18 C. Hellmich, K. Hofstetter, C. Kober Computational Micromechanics of Biological Materials: Bone and Wood ..........19 G. Holzapfel,C.T. Gasser, D. Kiousis Mechanobiology: Computation and Clinical Application .....................................20 B. Karihaloo, Q.Z. Xiao Recent Developments of Hybrid Crack Element: Determination of its Complete Displacement Field and Combination with XFEM...............................21 P. Ladevèze, P. Enjalbert, G. Puel, T. Romeuf Structural Model Validation and the Lack-of-Knowledge Theory........................22 J.V. Lemos Modeling of Historical Masonry with Discrete Elements .....................................23 G.-R. Liu, B.B.T. Kee A Regularized Strong-form Meshfree Method for Adaptive Analysis..................24 W. K. Liu Multiresolution Analysis for Material Design.......................................................25 R. Lackner, R. Blab, J. Eberhardsteiner, H. A. Mang Characterization and Multiscale Modeling of Asphalt – Recent Developments in Upscaling of Viscous and Strength Properties ..........................26 J.F. Dëu, W. Larbi, R. Ohayon Dissipative Interface Modeling for Vibroacoustic Problems – A New Symmetric Formulation.........................................................................................27
Table of Contents
vii
M. Papadrakakis, N.D. Lagaros, M. Fragiadakis Seismic Design Procedures in the Framework of Evolutionary Based Structural Optimization .........................................................................................28 L.F. González, L.H. Damp, J. Periaux, K. Srinivas High-fidelity Multi-Criteria Aero-Structural Optimisation Using Hierarchical Parallel Evolutionary Algorithms .....................................................29 E. Ramm, C. Förster, M. Neumann, W.A. Wall Interaction of Shells and Membranes with Incompressible Flows ........................30 J. N. Reddy, R.A. Arciniega Nonlinear Analysis of Composite and FGM Shells Using Tensor-Based Shell Finite Elements.............................................................................................31 R. Rolfes, G. Ernst, D. Hartung, J. Teßmer Strength of Textile Composites – A Voxel Based Continuum Damage Mechanics Approach .............................................................................................32 B. Schrefler, F. Pesavento, D. Gawin, M. Wyrzykowski Concrete at Early Ages and Beyond: Numerical Model and Validation ...............33 G. Schueller Uncertainty & Reliability Analysis of Structural Dynamical Systems..................34 Z. Waszczyszyn, L. ZiemiaĔski Neural Networks: New Results and Prospects of Applications in Structural Engineering ...........................................................................................................35 T. Ekevid, P. Kettil, H. Lane, N. E. Wiberg Computational Railway Dynamics........................................................................36 P. Wriggers and M. Hain Micro-Meso-Macro Modelling of Composite Materials .......................................37 A Computational Methods Organizers: Pereira, E.
M. Baitsch, T. Sikiwat, D. Hartmann (ID-1667) An Object-Oriented Approach to High Order Finite Element Analysis of Three-Dimensional Continua ............................................................. 38 E. Boerner, D. Mueller-Hoeppe, S. Loehnert, P. Wriggers A Finite Element Formulation Based on the Theory of a Cosserat Point - Extension to Ogden Material ..................................................................... 39
(ID-1984)
J. Eom, B. Lee A Macro Tetrahedral Element with Vertex Rotational D.O.F.s ................ 40
(ID-2456)
viii
Table of Contents
S. Fialko (ID-1659) Application of Aggregation Multilevel Iterative Solver to Problems of Structural Mechanics......................................................................... 41 A. Hansen, F. Rochinha Convergence Analysis of a Domain Decomposition Method with Augmented Lagrangian Formulation..................................................................... 42
(ID-2357)
Y. Kholodov, A. Kholodov, N. Kovshov, S. Simakov, D. Severov, A. Bordonos, A. Bapayev (ID-2279) Computational Models on Graphs for Nonlinear Hyperbolic and Parabolic System of Equations .............................................................................. 43 Ü. Lepik Haar Wavelet Method for Solving Integral Equations and Evolution Equations .............................................................................................. 44
(ID-1478)
H. Ostad-Hossein, S. Mohammadi A New Approach for Elimination of Dissipation and Dispersion Errors in Particle Methods..................................................................................... 45
(ID-2368)
Z. Pawlak, J. Rakowski Solution of Stability Problem of Infinite Plate Strips................................ 46
(ID-2155)
R. Robalo, M. Coimbra, A. Rodrigues Modeling Time-Dependent Partial Equations with Moving Boundaries by the Moving Finite Element Method............................................... 47
(ID-1838)
D. Rypl (ID-2072)
Discretization of Three-Dimensional Aggregate Particles ........................ 48
K. Sato Bending of an Elliptical Plate on Elastic Foundation and Under the Combined Action of Lateral Load and In-Plane Force.................................... 49
(ID-1733)
M. Silva, E. Pereira A Modal Analysis Approach Using an Hybrid-Mixed Formulation to Solve 2D Elastodynamic Problems ................................................................... 50
(ID-2560)
L. Veiga, J. Niiranen, R. Stenberg A New Finite Element Method for Kirchhoff Plates................................. 51
(ID-1970)
E. Zieniuk, A. Boltuc Non-Element Method for Solving 2D Boundary Problems Defined on Connected Polygonal Domains Described by Navier Equation.......... 52
(ID-2406)
Table of Contents
ix
B Computational Solid Mechanics Organizers: Martins, J.
S. Aitalyev, R. Baimakhan, Z. Masanov, N. Kurmanbekkyzy, G. Ylyasova (ID-2497) Computational Methods of Anisotropic Massif Mechanics Under Different Types of External Actions ..................................................................... 53 N. Alexandrova, P. Real Effect of Plastic Anisotropy on the Size of Elastic-Plastic Boundary in a Rotating Disk Problem................................................................... 54
(ID-1019)
E. Artioli, F. Auricchio, L. Veiga Numerical Testing on Return Map Algorithms for Von-Mises Plasticity with Nonlinear Hardening ..................................................................... 55
(ID-2068)
M. Asik (ID-2250)
A Model for the Analysis of Plates on a Layered Elastic Medium ........... 56
S. Benke Modeling of Solid State Transformations Using a Phase Field Model with Transformation Plasticity ................................................................... 57
(ID-1817)
S. Bosiakov, M. Zhuravkov Computer Modeling of Three-Dimensional Wave Movements in Anisotropic Elastic Environments ......................................................................... 58
(ID-1574)
R. Cardoso, V. Silva, H. Varum Visco-Elastic Regularization and Strain Softening ................................... 59
(ID-2411)
J. Cela, A. Piriz, M. Serna Numerical Simulations of the Rayleigh-Taylor Instability in Accelerated Solids ................................................................................................. 60
(ID-1108)
B. Diouf, F. Houdaigui, S. Poortmans, B. Verlinden, A. Habraken A Phenomenological Model to Simulate Mechanical Tests on Ultrafine-Grained Aluminum Produced by ECAE................................................ 61
(ID-2439)
E. Emmrich, O. Weckner The Peridynamic Equation of Motion in Non-Local Elasticity Theory ................................................................................................................... 62
(ID-1797)
A. Eraslan, E. Arslan Numerical Solution of Partially Plastic Curved Beam Problem................ 63
(ID-1232)
J. Fernandes, A. Alvim, R. Rocha A Proposal of Strain-Gage Rosette for Measurement Residual Stress Around a Circular Hole in a Plate with Circular Hole ................................ 64
(ID-1610)
J. Gómez, J. Royo, F. Martínez, E. Liarte, M. Jiménez Prediction of Dynamic Stiffness of Filled Rubber Mounts ....................... 65
(ID-1871)
x
Table of Contents
P. Grammenoudis, C. Tsakmakis (ID-1546) Size Effects in Finite Deformation Micropolar Plasticity ......................... 66 M. Grekov An Application of a Boundary Perturbation Method to Some Problems of Elasticity............................................................................................ 67
(ID-1888)
E. Grosu, I. Harari Spatial Stabilization of Semidiscrete Elastodynamics............................... 68
(ID-1005)
M. Grymer, M. Ekh, K. Runesson, T. Svedberg Modeling the Grain Size Effect Using Gradient Hardening and Damage in Crystal (Visco) Plasticity .................................................................... 69
(ID-1931)
T. Hata Stress-Focusing Effect Following Dynamically Transforming Strains in a Spherical Zirconia Inclusion............................................................... 70
(ID-1208)
E. Heikkola, S. Mönkölä, A. Pennanen, T. Rossi Controllability Method for the Solution of Linear Elastic Wave Equations............................................................................................................... 71
(ID-1469)
C. Husson, J. Richeton, S. Ahzi Development of a Flow Stress Model From Metals Using the Strain Rate/ Temperature Superposition Principle ................................................ 72
(ID-1590)
T. Kato, M. Kawahara Analysis of Elastic Body Using Kalman Filter Finite Element Method .................................................................................................................. 73
(ID-1827)
A. Lew, A. Eick Discontinuous Galerkin Methods for Nonlinear Elasticity ....................... 74
(ID-2100)
S. Marguet, P. Rozycki, L. Gornet A Rate Dependent Constitutive Model for Carbon-Fibre / EpoxyMatrix Woven Fabrics Submitted to Dynamic Loadings ...................................... 75
(ID-1870)
V. Matveyenko Solution of Viscoelasticity Problems Using Special Forms of Elastic Solutions .................................................................................................... 76
(ID-1798)
M. Mazdziarz Finite Elements Method Analysis of Influence of Contact Phenomena on Structure-Subsoil Interaction ........................................................ 77
(ID-1832)
M. Mizuno, Y. Sanomura Simulation of Inelastic Deformation of Polyethylene in Multiaxial State of Stress by Viscoelastic Constitutive Equtaion ........................................... 78
(ID-1286)
I. Pavlov Modeling of Granular Media by the 2D Discrete Lattice.......................... 79
(ID-1982)
Table of Contents
xi
M. Rabahallah, B. Bacroix, S. Bouvier, T. Balan (ID-2510) Crystal Plasticity Based Identification of Anisotropic Strain Rate Potentials for Sheet Metal Forming Simulation .................................................... 80 G. Romano, M. Diaco, R. Barretta A Geometric Approach to the Algorithmic Tangent Stiffness .................. 81
(ID-2044)
V. Sadovskii, O. Sadovskaya Parallel Computation of 3D Problems of the Dynamics of ElasticPlastic Granular Material Under Small Strains ..................................................... 82
(ID-1277)
Z. Uthman, H. Askes A Hyperelastodynamic Ale Formulation Based on Spatial and Material Forces...................................................................................................... 83
(ID-1328)
Y. Zhuk Monoharmonic Approach to Investigation of Heat Generation in the Viscoplastic Solids Under Harmonic Loading ................................................ 84
(ID-1073)
C Coupled Problems Organizers: Rodrigues, H.
S. Bargmann, P. Steinmann (ID-1021) A Continuous Galerkin Finite Element Method for Thermoelasticity Without Energy Dissipation ...................................................... 85 J. Blaszczuk, Z. Domanski The Model Coupling Liquid Bridge Between Ellipsoidal Grains ............. 86
(ID-2171)
M. Brehm, C. Bucher Reliability of Wavelet Packet System Identification................................. 87
(ID-1652)
L. Ecsi, P. Elesztos An Attempt to Simulate More Precisely the Behavior of a Solid Body Using New Energy Conservation Equation ................................................. 88
(ID-1112)
J. Gawinecki Mathematical Aspects of the Initial-Boundary Value Problems in Nonlinear Thermoelasticity of Simple and Non-Simple Materials ....................... 89
(ID-1361)
M. Guerich, S. Chaabane Effect of Parameter Uncertainties on a Vibro-Acoustic Design................ 90
(ID-2610)
G. Khodabakhshi, V. Nassehi, L. Shojai, R. Wakeman A Numerical Method for Solid-Liquid Interaction ................................... 91
(ID-2533)
A. Kiselev, O. Nekhaeva, A. Privalsky Computational Simulation of Irreversible Deforming and Fracture of Damageable Solids and Structures .................................................................... 92
(ID-1121)
xii
Table of Contents
M. Kropac, J. Murin (ID-2469) Solution of the Coupled Light-Mechanical Problems ............................... 93 I. Kurzhöfer, J. Schröder, H. Romanowski Simulation of the Ferroelectric Hysteresis Using a Hybrid Finite Element Formulation ............................................................................................. 94
(ID-1322)
R. Lanrivain, L. Silva, T. Coupez A Two-Phase Numerical Modelling of the Liquid Solid Transition in Polymer Processing ........................................................................................... 95
(ID-1338)
C. Leppert, D. Dinkler A Two-Phase Model for Granular Flows Applied to Avalanches............. 96
(ID-2596)
L. Margetts, I. Smith, J. Leng Parallel 3D Finite Element Analysis of Coupled Problems....................... 97
(ID-2218)
P. Porta, C. Vega Numerical Simulation of Rubber Curing Process with Application to Bladders Manufacture ....................................................................................... 98
(ID-1360)
E. Stupak, R. Kacianauskas, A. Dementjev, A. Jovaisa Coupled Finite Element Analysis of Composite Laser Rods Thermal Characteristics Under Longitudinal Diode Pumping .............................. 99
(ID-1475)
D Computational Structural Mechanics Organizers: Ambrósio, J.
T. Akis, T. Tokdemir, C. Yilmaz (ID-2480) On the Modeling of Nonplanar Shear Walls in Shear Wall-Frame Building Structures.............................................................................................. 100 F. Alamo, H. Weber, H. Espinoza Directional Drillstring Dynamics ............................................................ 101
(ID-2624)
M. Alinia, A. Rahai, S. Kazemi Mvm Energy Method for Buckling Analysis of Tapered Plates ............. 102
(ID-2651)
A. Alvarenga, R. Silveira Considerations on Advanced Analysis of Steel Portal Frames ............... 103
(ID-2119)
N. Azevedo, J. Lemos, J. Almeida A Discrete Element Model for the Fracture Analysis of Reinforced Concrete............................................................................................ 104
(ID-2569)
A. Baptista Analytical Criteria for the Evaluation of the Internal Forces at the Elastic and Plastic Limit States of Lozenge and Triangular Cross-Sections ....... 105
(ID-2700)
Table of Contents
xiii
M. Benachour, A. Hadjoui, M. Benguediab, N. Benachour, F. Hadjoui (ID-2252) Comparative Study of Aluminum Alloy Plate 2024/7050 Under the Effect of Internal Damping............................................................................ 106 A. Correia, F. Virtuoso Nonlinear Analysis of Space Frames ...................................................... 107
(ID-2648)
A. Davaran, A. Kashefi, S. Amiri Investigation of Shear Wall Behavior with Composite Boundary Elements .............................................................................................................. 108
(ID-1504)
M. Fard, S. Amiri, A. Kashefi An Investigation on Dynamic Behavior of Shear Walls on Flexible Foundation............................................................................................. 109
(ID-1096)
T. Fiedler, A. Öchsner, J. Grácio Influence of the Morphology of Adhesive Joining on the Mechanical Properties of Periodic Metal Hollow-Sphere-Structures.................. 110
(ID-1084)
H. Figueiredo, R. Calçada, R. Delgado Dynamic Behaviour of a Composite Twin Girder Bridge in a High Speed Interoperable Line..................................................................................... 111
(ID-2620)
A. Foces, J. Garrido, A. Moreno A Finite Element Model for Beam to Column Bolted Connections with Semi Rigid Behaviour ................................................................................. 112
(ID-1702)
G. Garcea, A. Madeo Rational Strain Measures - the Implicit Corotational Method................. 113
(ID-2353)
V. Kulbach, J. Idnurm Discrete and Continuous Analysis of Different Cable Structures ........... 114
(ID-1662)
Q. Li, V. Iu Three-Dimensional Vibration Analysis of Crystal Plates Via Ritz Method ................................................................................................................ 115
(ID-1072)
G. Lykidis, K. Spiliopoulos A 3D Solid Finite Element for Reinforced Concrete Analysis Allowing Slippage of Reinforcement .................................................................. 116
(ID-2233)
M. Lyly, J. Niiranen, R. Stenberg Some New Results on Mitc Plate Elements ............................................ 117
(ID-2000)
J. Neto, A. Assan Nonlinear Analysis of Reinforced Concrete Beams Considering the Slip Between Steel and Concrete................................................................... 118
(ID-1341)
J. Rijn Novel Semi-Analytical Methodology to Determine Model Parameters for a Simple Finite Element Bolt Model........................................... 119
(ID-2276)
xiv
Table of Contents
W. Rust, J. Overberg (ID-1803) Accounting for Fuselage Instabilities in the Coarse Model of an Aircraft Fuselage by Means of a Material Law ................................................... 120 J. Sosa, D. Owen, E. Neto, N. Petrinic Modelling of Reinforced Materials by a Subcycling Algorithm ............. 121
(ID-1530)
K. Spiliopoulos, T. Patsios Limit Analysis of Cable-Tied Structures................................................. 122
(ID-2329)
R. Steenbergen, J. Blaauwendraad Smart Super Elements in Slender Structures Subjected to Wind ............ 123
(ID-1516)
B. Trogrlic, A. Mihanovic, Z. Nikolic Nonlinear Analysis of Space R/C Frames with Non-Uniform Torsion ................................................................................................................ 124
(ID-2121)
G. Turvey, P. Wang An Fe Analysis of the Stresses in Pultruded GRP Single-Bolt Tension Joints and Their Implications for Joint Design ...................................... 125
(ID-1921)
J. Veiga, A. Henriques, J. Delgado An Efficient Evaluation of Structural Safety Applying Perturbation Techniques...................................................................................... 126
(ID-2688)
G. Yaoqing, L. Ke Semi-Analytical Analysis of Super Tall Building Bundled-Tube Structures............................................................................................................. 127
(ID-1214)
N. Zivaljic, A. Mihanovic, B. Trogrlic Large Displacements in Nonlinear Numerical Analyses for Cable Structures............................................................................................................. 128
(ID-1892)
E Industrial Applications Organizers: Pina, C.
V. Abadjiev, D. Petrova, E. Abadjieva (ID-1325) Mathematical Modeling for Synthesis and Design of NonOrthogonal Worm Gears with a Straight-Line Tooth Contact............................. 129 N. Ahmed, A. Mitrofanov, V. Silberschmidt, V. Babitsky Computational Modeling of Ultrasonically Assisted Turning................. 130
(ID-1675)
G. Anjos, R. Cunha, P. Kuklik, B. Miroslav Numerical Evaluation of Bored Piles in Tropical Soils by Means of the Geotechnical Engineering “Geo4” Fine Software..................................... 131
(ID-1694)
B. Atahanovich, B. Gayratovich Kinematics and Force Interaction of Screw Shaft with Variable Screw Course....................................................................................................... 132
(ID-1176)
Table of Contents
xv
J. Barglik, B. Ulrych (ID-2343) Optimal Construction of the Thermo-Elastic Actuator ........................... 133 M. Barros, C. Oliveira Determination of Moment-Curvature Diagrams and MomentDeflection Curves in Reinforced Concrete Beams .............................................. 134
(ID-2490)
P. Berke, T. Massart Numerical Simulation of the Nanoindentation Experiment: Sensitivity Analysis of the Experimental Parameters.......................................... 135
(ID-2274)
M. Chuda-Kowalska, A. Garstecki, Z. Pozorski Numerical Evaluation of Wrinkling Stress in Sandwich Panels ............. 136
(ID-1599)
I. Conde, M. Jiménez, J. Bielsa, E. Liarte, M. Laspalas Application of Fea As a Predictive Tool in the Corrugated Paperboard Industry ............................................................................................ 137
(ID-1881)
J. Dib, F. Bilteryst, J. Batoz, I. Lewon Implementation of 3D Homogenization Techniques for the Thermo-Elastic FEM Analysis of Brazed Plate-Fin Heat Exchangers ................ 138
(ID-2631)
R. Hoffmann Hierarchical Treecode for Optimized Collision Checking in Dem Simulations – Application on Electrophotographic Toner Simulations .............. 139
(ID-1003)
J. Kazanecki, Z. Pater, J. Bartnicki 3D FEM Analysis of Basic Process Parameters in Rotary Piercing Mill ...................................................................................................................... 140
(ID-2559)
M. Khoshravan, J. Shahimehr Numerical Evaluation of the Influence of Stiffener Rings on the Critical Buckling Pressure of the Vessels............................................................ 141
(ID-2239)
G. Kiziltas Topology Optimization and Fabrication of Multi-Material Dielectrics for Antenna Performance Improvements .......................................... 142
(ID-1754)
P. Klinge Reduction Method Independent Substructure Synthesis ......................... 143
(ID-1882)
M. Lancini, A. Magalini, D. Vetturi Discrete Models for the Simulation of Rubber Components Dynamics............................................................................................................. 144
(ID-1321)
A. Liao, H. Zhang, C. Wu Contact Analysis of Impeller-Shaft Assembly and Reasonably Designing the Amount Interference of Turbocompressors.................................. 145
(ID-1102)
Y. Sheng, C. Lawrence, B. Briscoe Study of the Stress Induced Granular Consolidation Process by 3D DEM Simulation............................................................................................ 146
(ID-1483)
xvi
Table of Contents
J. Shiau, C. Smith (ID-2577) Numerical Analysis of Passive Earth Pressures with Interfaces ............. 147 W. Wang, J. Wang, W. Shen, Z. Xu, W. Fan Three-Dimensional Finite Element Analysis of a Multi-Propped Deep Excavation in Shanghai Soft Deposit......................................................... 148
(ID-1273)
M. Zhuravkov, S. Bosiakov, S. Pronckevich The Computer Analysis of the Temperature Fields Arising in Bearing Node at Rotation of a Rotor ................................................................... 149
(ID-1579)
MS.01 Acoustics Structural Interactions Organizers:Tadeu, A.
V. Decouvreur, P. Ladevèze, P. Bouillard (ID-2023) Updating 3D Acoustic Models with the Constitutive Law Error Method. a Two Step Approach for Absorbing Material Characterization........... 150 J. García-Andujar, L. Fritz, J. López-Díez Analysis of Fluid-Structure Coupling by Statistical Energy Analysis............................................................................................................... 151
(ID-2109)
K. Ito, J. Toivanen Efficient Iterative Solution of Time-Harmonic Scattering by Objects in Layered Fluid ..................................................................................... 152
(ID-1608)
B. Neuhierl, E. Rank Computational Aeroacoustics by Coupling the Finite-Element and the Lattice-Boltzmann-Method............................................................................ 153
(ID-1186)
A. Panteghini, F. Genna, E. Piana Analysis of a Perforated Panel for the Correction of Low Frequency Resonances in Domestic Rooms........................................................ 154
(ID-1132)
A. Pereira, A. Tadeu Sound Insulation Provided by a Multi-Layer System Containing a Heterogeneity: a BEM Approach ........................................................................ 155
(ID-1252)
B. Pluymers, W. Desmet, D. Vandepitte, P. Sas An Efficient Wave Based Method for Steady-State VibroAcoustic Transmission Calculations ................................................................... 156
(ID-1864)
P. Santos, A. Tadeu Modeling Sound Radiation by Structures Caused by a Ground Impact Load: a BEM Approach........................................................................... 157
(ID-2270)
Table of Contents
xvii
MS.02 Smart Structures and Materials Organizers: Suleman, A., Benjeddou, A.
I. Arias, S. Serebrinsky, M. Ortiz (ID-1763) Cohesive Model of Electromechanical Fatigue for Ferroelectric Materials and Structures ...................................................................................... 158 H. Atzrodt, S. Herold, D. Mayer Simulation of Active Systems in a NVH Full Car Model ....................... 159
(ID-1500)
F. Auricchio, L. Petrini, A. Reali Toward an Exhaustive Modeling of the Macroscopic Behaviour of Shape Memory Alloys......................................................................................... 160
(ID-1911)
A. Benjeddou, J. Ranger Vibration Damping Using Resonant Shunted Shear-Mode Piezoceramics...................................................................................................... 161
(ID-1207)
I. Figueiredo, G. Stadler Optimal Control of Piezoelectric Anisotropic Plates .............................. 162
(ID-2619)
W. Gambin, A. Zarzycki Residual Internal Forces in Stiffened Thermal-Bimorph Actuator After Forming Process......................................................................................... 163
(ID-1559)
A. Gomes, A. Suleman Spectral Level Set Methodology in the Optimal Design of Adaptive Aeroelastic Structures .......................................................................... 164
(ID-1523)
D. Marinova, D. Lukarski, G. Stavroulakis, E. Zacharenakis Nondestructive Identification of Defects for Smart Plates in Bending Using Genetic Algorithms .................................................................... 165
(ID-2195)
J. Pereira, M. Pacheco, P. Pacheco, R. Aguiar, M. Savi Modeling Shape Memory Alloy Plane Truss Structures Using the Finite Element Method ........................................................................................ 166
(ID-2097)
G. Pirge, N. Kiliç, O. Uçan, S. Altintas Evaluation of Nimnga Magnetic Shape Memory Alloys Using Cellular Neural Networks.................................................................................... 167
(ID-2575)
C. Ramos, R. Oliveira, R. Campilho, A. Marques Modelling of Fibre Bragg Grating Sensor Plates .................................... 168
(ID-2645)
M. Trindade, A. Benjeddou Refined Finite Element Model for Vibration Analysis of Sandwich Beams with Shear Piezoelectric Actuators and Sensors ..................... 169
(ID-1309)
S. Ueda, H. Kondo Thermoelectromechanical Response of a Parallel Crack in a Functionally Graded Piezoelectric Strip.............................................................. 170
(ID-1724)
xviii Table of Contents
Y. Uetsuji, E. Nakamachi (ID-1833) Multi-Scale Finite Element Modeling of Piezoelectric Materials by a Crystallographic Homogenization Method.................................................. 171 H. Uyanik, Z. Mecitoglu Vibration Control of a Laminated Composite Plate Subjected to Blast Loading ...................................................................................................... 172
(ID-1490)
C. Vasques, R. Moreira, J. Rodrigues Experimental Identification of GHM and ADF Parameters for Viscoelastic Damping Modeling ......................................................................... 173
(ID-1960)
L. Wang, R. Melnik Numerical Aspects of Modelling Thermo-Mechanical Wave Propagation with Phase Transformations ............................................................ 174
(ID-1438)
A. Zabihollah, R. Ganesan, R. Sedaghati Analysis and Design Optimization of Smart Laminated Composite Beams Using Layerwise Theory.......................................................................... 175
(ID-2191)
MS.03 Asphalt Mechanics and Pavement Engineering Organizers: Lackner, R., Blab, R.
H. Benedetto, B. Delaporte, C. Sauzéat, M. Neifar (ID-2475) A Thermo-Viscoplastic Model for Bituminous Materials....................... 176 J. Croll From Asphalt to the Arctis: New Insights Into ThermoMechanical Ratchetting Processes....................................................................... 177
(ID-1149)
A. Holanda, E. Junior, T. Araujo, L. Melo, F. Junior, J. Soares An Object-Oriented System for Finite Element Analysis of Pavements............................................................................................................ 178
(ID-2557)
B. Lenhof, P. Kettil, K. Runesson, N. Wiberg On the Treatment of Convective Terms in Coupled HydroMechanics for Porous Media Subjected to Dynamic Loading ............................ 179
(ID-1804)
A. Molenaar Asphalt Mechanics, a Key Tool for Improved Pavement Performance Predictions...................................................................................... 180
(ID-1187)
MS.04 Biomechanical Simulations Organizers: Eriksson, A.
P. Blanco, I. Larrabide, S. Urquiza, R. Feijóo (ID-1858) Sensitivity of Blood Flow Patterns to the Constitutive Law of the Fluid .................................................................................................................... 181
Table of Contents
xix
A. Completo, F. Fonseca, J. Simoes (ID-2035) The Influence of Stem Design on Strains and Micromotion in Revision Total Knee Arthroplasty: Finite Element Analysis .............................. 182 A. Eriksson Optimization of Targeted Movements .................................................... 183
(ID-1192)
B. Heidari, D. Fitzpatrick, D. Mccormack, K. Synnott Persistence of Axial Rotation in Idiopathic Scoliosis Due to the Structural Changes of the Intervertebral Disc ..................................................... 184
(ID-1697)
H. Iwase, R. Himeno Numerical Simulation of Hemodynamcs in a Cerebral Artery ............... 185
(ID-1571)
A. John, M. Mazdziarz, J. Rojek, J. Telega, P. Maldyk Analysis of Some Contact Problems in Human Joints After Arthroplasty......................................................................................................... 186
(ID-1851)
P. Khayyer, A. Zolghadrasli, F. Daneshmand, A. Najafi Cardiovascular Disease Diagnosis Before Birth by Means of Chaotic Analysis on the Heart Rate Signal.......................................................... 187
(ID-1343)
I. Larrabide, R. Feijóo, E. Taroco, A. Novotny Configurational Derivative As a Tool for Image Segmentation.............. 188
(ID-1845)
G. Link, M. Kaltenbacher, R. Lerch Numerical Simulations to Analyze and Optimize the Human Substitute Voice .................................................................................................. 189
(ID-1670)
C. Nabais, R. Guedes, J. Simoes The Thaw Time of Frozen Cancellous Bone for Mechanical Testing................................................................................................................. 190
(ID-1843)
T. Olsson, J. Martins Modeling of Passive Behavior of Soft Tissues Including Viscosity and Damage......................................................................................................... 191
(ID-2414)
M. Racila, J. Crolet Nano and Macro Structure of Cortical Bone: Numerical Investigations....................................................................................................... 192
(ID-2288)
S. Rues, H. Schindler, K. Schweizerhof, J. Lenz Calculation of Muscle and Joint Forces in the Masticatory System........ 193
(ID-2403)
V. Vondrák, J. Rasmussen, M. Damsgaard, Z. Dostál The Algorithms of Mathematical Programming in Muscle Recruitment and Muscle Wrapping Problems ..................................................... 194
(ID-2177)
C. Yu, Y. Wang, Y. Liu, X. Sun Three-Dimensional Numerical Simulation of Airflow and Vibration Analysis for Upper Airway of Humans............................................... 195
(ID-2011)
xx
Table of Contents
MS.05 Computational Biomechanics Organizers: Rodrigues, H.
D. Balzani, J. Schröder, D. Gross (ID-1317) Computer Simulation of Anisotropic Damage and Residual Stresses in Atherosclerotic Arteries..................................................................... 196 J. Folgado, R. Andrade, P. Fernandes Computational Study on Stability and Bone Remodeling for a Hip Replacement Using a "Minimal Invasive" Femoral Stem ................................... 197
(ID-2493)
A. Fritsch, L. Dormieux, C. Hellmich Porous Polycrystals Built Up by Uniformly and Axisymmetrically Oriented Needles: Homogenization of Elastic Properties ................................... 198
(ID-1549)
U. Görke, H. Günther, M. Wimmer A Poroviscoelastic Overlay Model for Finite Element Analyses of Articular Cartilage at Large Strains..................................................................... 199
(ID-1924)
R. Guimaraes, S. Taylor, G. Blunn A Finite Element Study of Strain Distribution in an Instrumented Knee Prosthesis for Full Force Measurement in Vivo......................................... 200
(ID-2341)
I. Larrabide, R. Feijóo, E. Taroco, A. Novotny Topological Derivative Applied to Image Enhancement ........................ 201
(ID-1850)
J. Mcgarry, A. Pathak, L. Valdevit, A. Evans, P. Mchugh, R. Mcmeeking Determination of Contractile Forces Generated by Actin Fibre Networks ............................................................................................................. 202
(ID-2219)
R. Ruben, P. Fernandes, J. Folgado, H. Rodrigues Hip Prosthesis Design Using a Multi-Criteria Formulation .................... 203
(ID-2476)
S. Simakov, A. Kholodov, Y. Kholodov, A. Nadolskiy, A. Shushlebin Global Dynamical Model of the Cardiovascular System ........................ 204
(ID-1464)
S. Simakov, A. Kholodov, Y. Kholodov, A. Nadolskiy, A. Shushlebin Computational Study of the Vibrating Disturbances to the Lung Function............................................................................................................... 205
(ID-1467)
B. Simon, P. Rigby, T. Newberg, R. Park, S. Williams Abaqus-Based, Coupled Porohyperelastic Transport Finite Element Models for Soft Hydrated Biological Structures ................................... 206
(ID-1736)
J. Soares, J. Moore, K. Rajagopal Theoretical Modeling of Cyclically Loaded, Biodegradable Cylinders ............................................................................................................. 207
(ID-1979)
K. Subramani, M. Oliveira, J. Simoes Validation of a Non-Linear Wear Model for UHMWPE ........................ 208
(ID-1699)
Table of Contents
xxi
L. Zach, S. Konvickova, P. Ruzicka (ID-1782) FEA of Human Knee Joint Replacement Using Real Bone Models ....... 209 MS.06 Boundary Elements Organizers: Leitão, V.
G. Dziatkiewicz, P. Fedelinski (ID-1318) Subregion Boundary Element Method for Piezoelectric Structures........ 210 M. Guminiak, R. Sygulski Vibrations of System of Plates Immersed in Fluid by Bem .................... 211
(ID-1260)
S. Gupta, G. Degrande, H. Chebli, D. Clouteau, M. Hussein, H. Hunt A Coupled Periodic FE-BE Model for Ground-Borne Vibrations From Underground Railways .............................................................................. 212
(ID-2365)
A. Iban, J. Garcia-Teran, I. Rico On the Application of the Bem to Rubber-Elastic Materials................... 213
(ID-2163)
J. Rungamornrat Modeling of Darcy's Flow in Generally Anisotropic Porous Media Containing Discontinuity Surface by SGBEM-FEM Coupling........................... 214
(ID-1568)
E. Sapountzakis, V. Protonotariou A Displacement Solution to Transverse Shear Loading of Beams by BEM ............................................................................................................... 215
(ID-1002)
M. Schanz, T. Rüberg Non-Conforming Coupled Time Domain Boundary Element Analysis............................................................................................................... 216
(ID-2103)
MS.08 Advanced Composites Organizers: Reddy, J. N., Mota Soares, C.M., Benjeddou, A.
F. Ashida, S. Sakata, K. Matsumoto (ID-1749) Control of Thermal Stress in a Piezoelectric Composite Disk by a Stepwise Applied Electric Potential Distribution ................................................ 217 J. Baucom, M. Qidwai, J. Thomas Mitigation of Free-Edge Effects by Meso-Scale Structuring .................. 218
(ID-2372)
J. Bekuit, D. Oguamanam, O. Damisa A Quasi-2D Finite Element Formulation for Static and Dynamic Analysis of Sandwich Beams .............................................................................. 219
(ID-2151)
J. Belinha, L. Dinis A Numerical Comparison of Distinct Meshless Methods for the Analysis of Composite Laminates....................................................................... 220
(ID-1521)
xxii
Table of Contents
A. Benjeddou, S. Vijayakumar, I. Tawfiq (ID-1178) A New Damage Identification and Quantification Indicator for Piezoelectric Advanced Composites ................................................................... 221 A. Blom, S. Setoodeh, J. Hol, Z. Gürdal Design of Variable-Stiffness Conical Shells for Maximum Fundamental Frequency ...................................................................................... 222
(ID-1941)
P. Camanho, J. Mayugo, P. Maimí, C. Dávila A Micromechanics Based Damage Model for the Strength Prediction of Composite Laminates .................................................................... 223
(ID-1661)
J. Cardoso, N. Benedito, A. Valido Finite Element Analysis of Geometrically Nonlinear Thin-Walled Composite Laminated Beams.............................................................................. 224
(ID-2555)
J. Cardoso, A. Valido Design Sensitivity Analysis of Composite Thin-Walled Profiles Including Torsion and Shear Warping................................................................. 225
(ID-2626)
A. Carpentier, J. Barrau, L. Michel, S. Grihon Buckling Optimisation of Composite Panels Via Lay-Up Tables........... 226
(ID-2530)
J. Cognard, R. Créac'Hcadec Numerical Approach for the Design of Adhesively-Bonded Assemblies .......................................................................................................... 227
(ID-1335)
G. Dvorak, Y. Bahei-El-Din Enhancement of Blast Resistance of Sandwich Plates ............................ 228
(ID-2689)
C. Friebel, I. Doghri, V. Legat Mechanics and Acoustics of Viscoelastic Composites by a MicroMacro Mean-Field Approach .............................................................................. 229
(ID-1337)
P. Fuschi, A. Pisano Numerical Evaluation of Upper and Lower Bounds to the Collapse Limit Load for Composite Laminates................................................... 230
(ID-2346)
K. Kalnins, J. Auzins, R. Rikards Material Degradation Assessment for Stiffened Composite Shells Using Metamodelling Approach ......................................................................... 231
(ID-2049)
M. Karama, K. Afaq, S. Mistou A New Model for the Behaviour of the Multi-Layer Material Interfaces ............................................................................................................. 232
(ID-1981)
L. Kärger, J. Baaran, J. Teßmer Fe-Tool Codac for an Efficient Simulation of Low-Velocity Impacts on Composite Sandwich Structures ....................................................... 233
(ID-1101)
Table of Contents
xxiii
J. Kato, A. Lipka, E. Ramm (ID-2603) Preliminary Investigation for Optimization of Fiber Reinforced Cementitious Composite Structures .................................................................... 234 P. Kere, M. Lyly On Post-Buckling Analysis and Experimental Correlation of Cylindrical Composite Shells .............................................................................. 235
(ID-1801)
M. Laspalas, S. Maynar, C. Crespo, M. Jiménez, B. García Application of Failure Criteria to Short Fiber Reinforced Composites and Experimental Validation ........................................................... 236
(ID-1891)
C. Lopes, Z. Gürdal, P. Camanho Tow-Placed, Variable-Stiffness Composite Panels: Damage Tolerance Improvements Over Traditional Straight-Fibre Laminates................. 237
(ID-2153)
F. Melo, R. Moreira, J. Rodrigues A Mixed-Formulation Four-Node Rectangular Element in the Modeling of Laminate Composite Beam Stuctures............................................. 238
(ID-2052)
T. Messager, P. Chauchot, B. Bigourdan Optimal Design of Stiffened Composite Underwater Hulls .................... 239
(ID-1333)
J. Moita, C. Soares, C. Soares Higher Order Model for Analysis of Magneto-Electro-Elastic Plates ................................................................................................................... 240
(ID-1115)
F. Moleiro, C. Soares, C. Soares, J. Reddy Mixed Least-Squares Finite Element Model for the Static Analysis of Laminated Composite Plates ............................................................ 241
(ID-1508)
M. Nader, H. Garssen, H. Irschik Applications of Distributed Piezoelectric Electrode Patches for Active Noise and Vibration Control.................................................................... 242
(ID-1289)
E. Ng, A. Suleman Computational Elastoplatic Modeling of Multi-Phase FiberReinforced Composites ....................................................................................... 243
(ID-1554)
K. Niessen, J. Moreno, R. Gadow Evolution and Analysis of Stresses in Thixoforged Metal Matrix Composites .......................................................................................................... 244
(ID-2236)
M. Pietrzakowski Piezoelectric Control of Composite Plate Vibration: Effect of Electric Field Distribution ................................................................................... 245
(ID-1222)
H. Santos, C. Soares, C. Soares, J. Reddy A Finite Element Model for the Analysis of 3D Axisymmetric Laminated Shells with Embedded Piezoelectric Sensors and Actuators ............. 246
(ID-1082)
xxiv Table of Contents
J. Santos, H. Lopes, M. Vaz, C. Soares, C. Soares, M. Freitas (ID-1239) Damage Localization in Laminated Composite Plates Using Double Pulse-Electronic Holographic Interferometry ......................................... 247 E. Sapountzakis Shear Deformation Effect in Nonlinear Analysis of Spatial Composite Beams in Variable Axial Loading by BEM ...................................... 248
(ID-1139)
C. Schuecker, H. Pettermann Constitutive Ply Damage Modeling, FEM Implementation, and Analyses of Laminated Structures....................................................................... 249
(ID-1759)
W. Wagner, C. Balzani Simulation of Delamination in Stringer Stiffened FiberReinforced Composite Shells .............................................................................. 250
(ID-1204)
MS.10 Computational Fracture Mechanics Organizers: Leung, A.
A. Andreev (ID-1632) Development of Methods of Numerical Solution of Singular Integro-Differential Equations for Solid Mechanics Problems ........................... 251 I. Arias, J. Knap, V. Chalivendra, S. Hong, M. Ortiz, A. Rosakis Validation of Large Scale Simulations of Dynamic Fracture.................. 252
(ID-2247)
E. Giner, A. Vercher, O. González, J. Tarancón, F. Fuenmayor Crack Growth in Fretting-Fatigue Problems Using the Extended Finite Element Method ........................................................................................ 253
(ID-2196)
S. Jox, P. Dumstorff, G. Meschke Aspects of Crack Propagation and Hygro-Mechanical Coupling Using X-FEM ...................................................................................................... 254
(ID-2536)
S. Klishin Destruction of Rocks by Directional Hydraulic Fracturing on the Basis of Models of Plasticity with Internal Variables ......................................... 255
(ID-1287)
N. Krukova, I. Lavit The Finite-Element Method in Linear Fracture Mechanics Problems.............................................................................................................. 256
(ID-1638)
R. Larsson, M. Fagerström Finite Deformation Fracture Modelling of a Thermo-Mechanical Cohesive Zone..................................................................................................... 257
(ID-1471)
N. Myagkov, T. Shumikhin Critical Behavior and Energy Dependence of Mass Distribution in High-Velocity Impact Fragmentation.................................................................. 258
(ID-1145)
Table of Contents
xxv
S. Reese, P. Wriggers (ID-2419) One 3D Adaptive Fragmentation Procedure for the Explicit Simulation of Brittle Material Cracking .............................................................. 259 G. Tsamasphyros, T. Papathanassiou Finite Element Analysis of Cracked Plates with Circular Stress Raisers Used for S.I.F. Reduction ....................................................................... 260
(ID-2441)
N. Vlasov, I. Fedik Simulation of Materials Damage in the Field of Internal Stresses .......... 261
(ID-2230)
MS.11 Computational Mathematics Organizers: Stenberg, R., Figueiredo, I.
F. Bourquin (ID-2063) Computational Methods for the Fast Boundary Stabilization of Flexible Plates ..................................................................................................... 262 L. Costa, I. Figueiredo, P. Oliveira Sensor and Actuator Capabilities of a Laminated Piezoelectric Plate Model ......................................................................................................... 263
(ID-1835)
A. Loula, M. Correa Numerical Analysis of Stabilized Finite Element Methods for Darcy Flow .......................................................................................................... 264
(ID-2187)
C. Lovadina, R. Stenberg An Error Estimator for the Reissner-Mindlin Plate Problem .................. 265
(ID-1223)
N. Troyani, E. Gutiérrez A Convergence Study of the Numerical Solution of Two BiDirectionally Coupled Partial Differential Equations in Thermoelectricity ........ 266
(ID-1069)
MS.12 Computational Methods for Anisotropic Material Behaviour at Large Strains Organizers: Sansour, C.
M. Böl, S. Reese (ID-1440) Numerical Simulations of Rubber-Like Materials Under Changing Directions ............................................................................................................ 267 A. Bucher, U. Görke, R. Kreißig About an Efficient and Consistent Numerical Strategy for the Solution of the Initial-Boundary Value Problem................................................. 268
(ID-1920)
H. Hein Vibrations of Composite Beams with Multiple Delaminations............... 269
(ID-1482)
xxvi Table of Contents
I. Karsaj, C. Sansour, J. Soric (ID-2382) Computational Aspects of Anisotropic Finite Strain Plasticity Based on the Multiplicative Decomposition........................................................ 270 A. Menzel Adaptation of Biological Tissues - a Fibre Reorientation Model for Orthotropic Multiplicative Growth ................................................................ 271
(ID-1883)
J. Schröder, P. Neff Polyconvex Anisotropic Hyperelastic Energies ...................................... 272
(ID-1589)
J. Wang, V. Levkovitch, B. Svendsen Micromechanically Motivated Phenomenological Modeling of Induced Flow Anisotropy and Its Application to Sheet Forming Processes........ 273
(ID-1486)
MS.13 Computational Modelling of Masonry Structures Organizers: Lourenço, P.
A. Barbieri, A. Cecchi, A. Tommaso (ID-1199) 3D Homogenization Procedure for Load Bearing Masonry Columns .............................................................................................................. 274 C. Calderini, S. Lagomarsino Non Linear Modelling of Masonry Structures Under Cyclic Loads ....... 275
(ID-1809)
S. Casolo, C. Sanjust Macroscale Modelling of Structured Materials with Damage by a Specific Rigid Element Model ............................................................................ 276
(ID-1862)
A. Cecchi Plate Micromechanical Models for 3D Periodic Brickworks.................. 277
(ID-1027)
A. Cecchi, G. Milani, A. Tralli Limit Analysis of Out-Of-Plane Loaded Running Bond Masonry Walls Under Mindlin-Reissner Plate Hypotheses ............................................... 278
(ID-1140)
M. Malena, A. Bilotta, A. Lanzo Nonlinear Analysis of Brittle Materials .................................................. 279
(ID-1762)
T. Massart, R. Peerlings, M. Geers Damage Localisation in Computational Homogenisation of Masonry and Its Incorporation in a Two-Scale Computational Framework........ 280
(ID-2179)
G. Milani, P. Lourenço, A. Tralli 3D Homogenized Limit Analysis of Masonry Buildings Subjected to Horizontal Loads ............................................................................................. 281
(ID-1131)
F. Peña, P. Lourenço, J. Lemos Modelling the Dynamic Behaviour of Masonry Walls As Rigid Blocks.................................................................................................................. 282
(ID-1256)
Table of Contents xxvii
G. Zingone, G. Canio, L. Cavaleri (ID-2514) On the Improvement of Monumental Structure Safety: a Case Study.................................................................................................................... 283 A. Zucchini, P. Lourenço Homogenization of Masonry Using a Micro-Mechanical Model: Compressive Behaviour....................................................................................... 284
(ID-1056)
MS.14 Computational Stochastic Failure Mechanics Organizers: Gutierrez, M. A.
R. Jimenez-Rodriguez, L. Lacoma (ID-1756) Uncertainty Characterization and Settlement Analyses: the Importance of Distribution Types........................................................................ 285 M. Vorechovsky, R. Chudoba, J. Jerábek Adaptive Probabilistic Modeling of Localization, Failure and Size Effect of Quasi-Brittle Materials ......................................................................... 286
(ID-1885)
MS.15 Computational Stochastic Structural and Uncertainty Analysis Organizers: Schueller, G.
D. Alvarez (ID-1625) On the Use of Infinite Random Sets for Bounding the Probability of Failure in the Case of Parameter Uncertainty.................................................. 287 J. Colliat, M. Krosche, M. Krosche, M. Hautefeuille, A. Ibrahimbegovic, R. Niekamp, H. Matthies (ID-2470) Stochastic Analysis of Coupled Nonlinear Thermo-Mechanical Problems: SFEM Model ...................................................................................... 288 J. Crempien-Laborie Response of a Single Degree of Freedom Elastic Perfectly Plastic System Under Non-Stationary Gaussian Seismic Excitation .............................. 289
(ID-1064)
D. Degrauwe, G. Roeck, G. Lombaert Fuzzy Frequency Response Function of a Composite Floor Subject to Uncertainty by Application of the GĮd Algorithm............................. 290
(ID-1999)
J. Fernandes, M. Pinho, A. Alvim, A. Pithon Comparative Numerical Evaluation of Angra I Auxiliary Feedwater System Reliability by the Method of Suplementary Variables .......... 291
(ID-1611)
M. Galffy, M. Baitsch, A. Wellmann-Jelic, D. Hartmann Lifetime Estimation of Vertical Bridge Tie Rods Exposed to Wind-Induced Vibrations .................................................................................... 292
(ID-1088)
xxviii Table of Contents
G. Giunta, E. Carrera (ID-1544) Stochastic Static Analyses of FE Models by Means of Newton's Series Expansions................................................................................................ 293 M. Grigoriu A Galerkin Solution for Stochastic Algebraic Equations ........................ 294
(ID-1262)
R. Iwankiewicz, M. Vasta Approximate Method for Probability Density of the Response of a Linear Oscillator to a Non-Poisson Impulse Process........................................ 295
(ID-1906)
H. Kang, Y. Lee, J. Huh, B. Kwak Comparative Study of RBDO Algorithms Based on Form and FAMM................................................................................................................. 296
(ID-2625)
M. Mailhé, S. Chaabane, F. Léné, G. Duvaut, S. Grihon Probabilistic Analysis and Optimization of a Fully Composite Cylinder............................................................................................................... 297
(ID-2589)
A. Martowicz, L. Pieczonka, T. Uhl Assessment of Dynamic Behaviour of Spot Welds with Uncertain Parameters Using Genetic Algorithms Application............................................. 298
(ID-1316)
M. Munck, D. Moens, W. Desmet, D. Vandepitte Optimisation Algorithms for Non-Deterministic Dynamic Finite Element Analysis of Imprecisely Defined Structures.......................................... 299
(ID-1926)
M. Pellissetti, H. Pradlwarter, G. Schuëller Relative Importance of Uncertain Parameters in Aerospace Applications ........................................................................................................ 300
(ID-2699)
V. Potapov Stability of Elastic and Viscoelastic Systems Under Stochastic Non-Gaussian Excitation..................................................................................... 301
(ID-1175)
J. Santos, B. Mace Modelling Uncertainty in Mechanical Joint Parameters Using Component Modal and Fuzzy Approaches.......................................................... 302
(ID-2348)
E. Sibilio, J. Beck, M. Muto, M. Ciampoli Bayesian Model Updating Approach for Ground-Motion Attenuation Relations .......................................................................................... 303
(ID-2650)
C. Verhoosel, M. Gutiérrez, S. Hulshoff Iterative Solution of the Random Eigenvalue Problem ........................... 304
(ID-1205)
Table of Contents
xxix
MS.16 Contact Mechanics Organizers: Martins, J.
J. Bielsa, R. Rodríguez, L. Vila, M. Jiménez (ID-2076) Parametrized Finite Element Analysis of Tribological Instabilities on Polymer-Metal Sliding Contacts .................................................................... 305 D. Boso, P. Litewka, B. Schrefler, P. Wriggers Thermo-Electro-Mechanical Coupling in Beam-to-Beam Contact ......... 306
(ID-2104)
M. Campo, J. Fernandez, K. Kuttler, M. Shillor Numerical Analysis of a Dynamic Frictional Viscoelastic Contact Problem with Damage ......................................................................................... 307
(ID-1133)
A. Chernov, M. Maischak, E. Stephan Hp-Mortar Boundary Element Method and FE/BE Coupling for Multibody Contact Problems with Friction ......................................................... 308
(ID-1991)
G. Chevallier, D. Nizerhy Friction Induced Vibrations in a Clutch System. Consequences on the Apparent Friction Torque. ............................................................................. 309
(ID-2328)
A. Chudzikiewicz, A. Myslinski Thermoelastic Wheel - Rail Contact Problem with Temperature Dependent Friction Coefficient ........................................................................... 310
(ID-1704)
M. Cocou, M. Raous, M. Schryve Analysis of a Dynamic Contact Problem with Adhesion and Friction in Viscoelasticity.................................................................................... 311
(ID-2078)
G. Drossopoulos, G. Stavroulakis, C. Massalas Influence of the FRP Strengthening, the Shape and the Movement of Abutments on the Collapse of Arch Stone Bridges......................................... 312
(ID-2194)
R. Dzonou, M. Marques, L. Paoli Sweeping Process for Vibro-Impact Problem with a General Inertia Operator ................................................................................................... 313
(ID-1020)
A. Eddhahak, L. Chevalier, S. Cloupet On a Simplified Method for Wear Simulation in Rolling Contact Problems.............................................................................................................. 314
(ID-1251)
G. Festa, J. Vilotte Spectral Element Simulations of Rupture Dynamics Along Planar and Kinked Frictional Faults .............................................................................. 315
(ID-1312)
M. Foerg, T. Geier, L. Neumann, H. Ulbrich R-Factor Strategies for the Augmented Lagrangian Approach in Multi-Body Contact Mechanics........................................................................... 316
(ID-1480)
xxx
Table of Contents
L. Fourment, S. Guerdoux (ID-1217) A Simple Smoothing Procedure of 3D Surfaces for Accurate Contact Analysis: Application to Metal Forming Problems................................ 317 D. Gabriel, J. Plesek, F. Vales, M. Okrouhlík Symmetry Preserving Algorithm for a Dynamic Contact-Impact Problem ............................................................................................................... 318
(ID-2524)
H. Georgiadis, D. Anagnostou Problems of Concentrated Loads in Microstructured Solids Characterized by Dipolar Gradient Elasticity...................................................... 319
(ID-1342)
F. Gutzeit, M. Wangenheim, M. Kröger An Experimentally Validated Model for Unsteady Rolling .................... 320
(ID-1925)
S. Hartmann, S. Brunssen, E. Ramm, B. Wohlmuth A Primal-Dual Active Set Strategy for Unilateral Non-Linear Dynamic Contact Problems of Thin-Walled Structures ...................................... 321
(ID-2576)
Y. Kanno, J. Martins Arc-Length Method for Frictional Contact with a Criterion of Maximum Dissipation of Energy ........................................................................ 322
(ID-1573)
H. Khenous, P. Laborde, Y. Renard A Energy Conserving Approximation for Elastodynamic Contact Problems.............................................................................................................. 323
(ID-2170)
A. Konyukhov, K. Schweizerhof, P. Vielsack On Models of Contact Surfaces Including Anisotropy for Friction and Adhesion and Their Experimental Validations............................................. 324
(ID-2320)
R. Krause Fast and Robust Solution Methods for Dynamic Contact Problems ....... 325
(ID-2147)
M. Marques, L. Paoli A Velocity-Based Time-Stepping Method for Frictional Dynamics....... 326
(ID-1865)
T. Meyer, A. Gal, M. Klüppel Mechanical Modeling of Friction and Adhesion of Elastomers at Rough Interfaces.................................................................................................. 327
(ID-1785)
C. Miranda, M. Neto, G. Fainer A 9M Drop Test Simulation of a Dual Purpose Cask for Nuclear Research Reactors Spent Fuel Elements.............................................................. 328
(ID-1347)
U. Nackenhorst, M. Ziefle A Discontinuous Galerkin Approach for the Numerical Treatment........ 329
(ID-1745)
P. Neittaanmäki, A. Kravchuk, I. Goryacheva An Iterative Method with BEM Discretization for the Friction Contact Problems ................................................................................................ 330
(ID-1297)
Table of Contents
xxxi
J. Nettingsmeier, P. Wriggers (ID-1299) Frictional Contact of Elastomer Materials on Rough Rigid Surfaces ............................................................................................................... 331 M. Oliveira, J. Alves, L. Menezes Optimizing the Description of Forming Tools with Bézier Surfaces in the Numerical Simulation of the Deep Drawing Process.................. 332
(ID-1856)
E. Pratt, A. Léger Exploring the Dynamics of a Simple System Involving Coulomb Friction ................................................................................................................ 333
(ID-2367)
F. Rauter, J. Pombo, J. Ambrósio, M. Pereira Multibody Modeling of Pantographs for Catenary-Pantograph Interaction............................................................................................................ 334
(ID-1653)
M. Renouf, V. Acary Comparison and Coupling of Algorithms for Collisions, Contact and Friction in Rigid Multibody Simulations...................................................... 335
(ID-2436)
M. Renouf, A. Saulot, Y. Berthier Third-Body Flow During Wheel-Rail Interaction .................................. 336
(ID-2440)
J. Sá, S. Grégoire, P. Moreau, D. Lochegnies Modelling Thermal Contact Resistance on Glass Forming Processes with Special Interface Finite Elements................................................ 337
(ID-2352)
J. Shiau Numerical Investigation of Shakedown Residual Stresses Under Moving Surface Loads ........................................................................................ 338
(ID-1734)
N. Strömberg Frictional Contact/Impact Between a Hyperelastic Body and Moving Rigid Obstacles ...................................................................................... 339
(ID-1578)
J. Svígler Incorrect Contact of Screw Surfaces and Its Consequences.................... 340
(ID-1485)
K. Uenishi Three-Dimensional Rupture Instability of a DisplacementSoftening Interface Under Nonuniform Loading................................................. 341
(ID-1104)
K. Willner, D. Görke Contact of Rough Surfaces - a Comparison of Numerical and Experimental Results........................................................................................... 342
(ID-1288)
xxxii Table of Contents
MS.17 Continnum Models for Nano-Structures Organizers: Kompis, V.
M. Arroyo, T. Belytschko (ID-1543) Continuum Mechanics Modelling and Simulation of Carbon Nanotubes............................................................................................................ 343 L. Bochkareva, M. Kireitseu, G. Tomlinson Comparison of Computational Efficiency of Modeling Approaches to Prediction of Damping Behavior................................................. 344
(ID-1144)
P. Dluzewski, M. Mazdziarz, G. Jurczak, P. Traczykowski, S. Nagao, R. Nowak, K. Kurzydlowski (ID-1849) A Hybrid Atomistic-–Continuum Finite Element Modelling of Nanoindentation Test on Copper......................................................................... 345 V. Kompis, M. Stiavnický, M. Kaukic Continuum Models for Composites Reinforced by Micro/Nano Fibers................................................................................................................... 346
(ID-1741)
A. Kushima, Y. Umeno, T. Kitamura First Principles Evaluation of Ideal Strength of Cu Nanowire ................ 347
(ID-2339)
S. Lisina, A. Potapov Variation Descriptions of Nano-Structured Media.................................. 348
(ID-1668)
T. Messager, P. Cartraud Homogenization of Single-Walled Carbon Nanotubes ........................... 349
(ID-1234)
M. Rabia Phonon Scattering by Perturbed Multichannel Waveguides ................... 350
(ID-1010)
H. Wu, X. Wang An Atomistic-Information-Based Continuum Inhomogeneous Material Model for Metal Nanorod ..................................................................... 351
(ID-1086)
MS.18 Coupling Problems Organizers: Schrefler, B.
F. Duda, L. Guimarães, A. Souza, J. Barbosa (ID-2349) On the Modeling of Deformation-Diffusion-Damage Coupling in Elastic Solids ....................................................................................................... 352 J. Gatica, V. Pita, N. Brum Frost Growth on Cold Flat Plate: a Correlation for the Diffusion Resistance Factors ............................................................................................... 353
(ID-1698)
Table of Contents xxxiii
D. Khalmanova, F. Costanzo (ID-1532) Discontinuous Space-Time Galerkin Finite Element Method in Linear Dynamic Fully Coupled Thermoelastic Problems with Strain and Heat Flux Discontinuities .................................................................................... 354 M. Landervik, R. Larsson Pore Gas Interaction in Polymeric Foams with Respect to Energy Absorption........................................................................................................... 355
(ID-1463)
F. Meftah, H. Sabeur A Thermo-Hydro–Damage Model for the Dehydration Creep of Concrete Subjected to High Temperature............................................................ 356
(ID-2290)
D. Néron, L. Pierre, B. Schrefler A Time-Space Framework Suitable for the LATIN Computational Strategy for Multiphysics Problems .................................................................... 357
(ID-2483)
W. Oliveira, M. Savi, P. Pacheco, L. Souza Finite Element Analysis of the Thermomechanical Coupling in Quenching of Steel Cylinders Using a Constitutive Model................................. 358
(ID-2176)
B. Pichler, C. Hellmich, H. Mang A Combined Fracture-Micromechanics Model for Tensile StrainSoftening in Brittle Materials .............................................................................. 359
(ID-1550)
Ö. Sen, D. Turhan Transient Dynamic Response of Thermoelastic Cylindrical Layered Media..................................................................................................... 360
(ID-1491)
MS.19 Damage Organizers: Alfaiate, J.
H. Askes, M. Gutiérrez, A. Rodriguez-Ferran (ID-2083) Novel Nonlocal Continuum Formulations. Part 1: Gradient Elasticity Based on Nonlocal Displacements and Nonlocal Strains .................... 361 T. Bennett, S. Kulasegaram On the Use of a Damage Model Based on Non-Local Displacements in the Element-Free Galerkin Method......................................... 362
(ID-1514)
T. Domingues, J. Alfaiate Modelling of Reinforced Concrete Beams Strengthened with PreStressed CFRP..................................................................................................... 363
(ID-2350)
T. Fiedler, L. Cunda, A. Öchsner, G. Creus, J. Grácio Numerical and Experimental Studies of Damage in Porous Materials.............................................................................................................. 364
(ID-1203)
xxxiv Table of Contents
R. Frizzell, C. Mccarthy, D. Cronin, M. Mccarthy, R. O'Higgins (ID-2369) The Development of a Continuum Damage Model for Fibre Metal Laminate Structures............................................................................................. 365 M. Hassanzadeh, G. Fagerlund Residual Strength of the Frost-Damaged Reinforced Concrete Beams .................................................................................................................. 366
(ID-1872)
M. Konrad, R. Chudoba, B. Kang Numerical and Experimental Evaluation of Damage Parameters for Textile Reinforced Concrete Under Cyclic Loading..................................... 367
(ID-2057)
P. Neto, J. Alfaiate, J. Vinagre Modeling the Behavior of Reinforced Concrete Beams Strengthened with FRP........................................................................................ 368
(ID-2380)
S. Oliveira, N. Gaspar, P. Dinis Cracking Analysis in Concrete Dams Using Isotropic Damage Models. Objectivity of Numerical Solutions ....................................................... 369
(ID-2649)
R. Pedersen, A. Simone, B. Sluys Continuous-Discontinuous Modelling of Dynamic Failure of Concrete Using a Viscoelastic Viscoplastic Damage Model............................... 370
(ID-1962)
J. Pituba On the Formulation of Damage Constitutive Models for Bimodular Anisotropic Media ............................................................................. 371
(ID-2089)
L. Rosa, E. Carvalho, B. Danziger Soil-Structure Interaction - Case History Analysis Involving Structural Damage............................................................................................... 372
(ID-2540)
Y. Sanomura, K. Saitoh Evolution Equation of Creep Damage Under Stress Variation ............... 373
(ID-1737)
A. Sichaib, G. Mounajed, C. Laborderie, H. Boussa, H. Quoc Concrete Damage Model Adaptation for Cyclic Loading....................... 374
(ID-1746)
C. Silva, L. Castro Hybrid and Mixed Finite Element Formulations for Softening Materials.............................................................................................................. 375
(ID-1107)
D. Sornin, K. Saanouni Theoretical and Computational Aspects of an Elastoplastic Damage Gradient Non Local Model ................................................................... 376
(ID-1326)
J. Wu, J. Li On a New Framework for Anisotropic Damage Model .......................... 377
(ID-1616)
Table of Contents xxxv
MS.20 Design Optimization Under Uncertainty Organizers: Choi, K. K. (USA), Kwak, B. M., Gorsich, D.
N. Banichuk, S. Ivanova, E. Makeev, A. Sinitsin (ID-2572) Shell Optimization Under Constraint on Damage Accumulation ........... 378 J. Casaca, A. Gomes Design of Acceptance-Sampling Plans Under Bayesian Risk................. 379
(ID-1249)
E. Cherkaev, A. Cherkaev Optimal Design for the Worst Case Scenario.......................................... 380
(ID-2192)
K. Choi, I. Lee, D. Gorsich Dimension Reduction Method for Reliability-Based Robust Design Optimization............................................................................................ 381
(ID-2522)
R. Dippolito, S. Donders, L. Hermans, M. Hack, J. Peer, N. Tzannetakis A Fatigue Life Reliability-Based Design Optimization of a Slat Track Using Mesh Morphing .............................................................................. 382
(ID-1231)
B. Kwak, J. Chang, J. Kim A New Approach of Robust Design Based on the Concept of Allowable Load Set ............................................................................................. 383
(ID-2571)
T. Lee, J. Jung, D. Jung A Sampling Technique Enhancing Accuracy and Efficiency of Metamodel-Based RBDO: Constraint Boundary Sampling ................................ 384
(ID-2593)
D. Moens, D. Vandepitte Interval Sensitivity Analysis of Dynamic Response Envelopes for Uncertain Mechanical Structures......................................................................... 385
(ID-2139)
C. Poloni, P. Geremia, A. Clarich Multi-Objective Robust Design Optimization of an Engine Crankshaft ........................................................................................................... 386
(ID-1904)
Y. Ryu Development and Application of a New Metropolis GA for the Structural Design Optimization ........................................................................... 387
(ID-2570)
B. Youn, Z. Xi, L. Wells, D. Lamb Stochastic Response Surface Using the Enhanced DimensionReduction (EDR) Method for Reliability-Based Robust Design......................... 388
(ID-2539)
MS.21 Differential Quadrature, Generalized Methods and Related Discrete Element Analysis Methods Organizers: Chen, C.
R. Balevicius, R. Kacianauskas (ID-1499) DEM Analysis of Granular Flow in Pyramidal Hoppers ........................ 389
xxxvi Table of Contents
C. Chen (ID-2085) DQEM and DQFDM for Computational Mechanics Problems .............. 390 C. Cinquini, M. Bruggi, P. Venini An Innovative Truly-Mixed Method for Cohesive-Crack Propagation Problems.......................................................................................... 391
(ID-1191)
D. Rosillo, F. Pérez Compactly Supported Fundamental Functions for Spline-Based Differential Quadrature ....................................................................................... 392
(ID-1876)
F. Tornabene, E. Viola Differential Quadrature Solution for Parabolic Structural Shell Elements .............................................................................................................. 393
(ID-2347)
MS.23 Enriched and Enhanced Finite Element Technology Organizers: Areias, P.
E. Budyn, L. Henry, T. Hoc (ID-2167) Multiple Crack Growth Failure in Cortical Bone Under Tension by the Extended Finite Element Method ............................................................. 394 F. Cirak Subdivision Shells................................................................................... 395
(ID-1710)
C. Foster, R. Borja Capturing Slip Weakening and Variable Frictional Response in Localizing Geomaterials Using an Enhanced Strain Finite Element................... 396
(ID-2040)
L. Hazard, P. Bouillard, J. Sener A Partition of Unity Finite Element Method Applied to the Study of Viscoelastic Sandwich Structures ................................................................... 397
(ID-1972)
A. Kölke, A. Legay An Enriched Space-Time Finite Element Method for FluidStructure Interaction - Part Ii: Thin Flexible Structures ...................................... 398
(ID-2318)
A. Legay, A. Kölke An Enriched Space-Time Finite Element Method for FluidStructure Interaction- Part I: Prescribed Structural Displacement....................... 399
(ID-2316)
I. Moldovan, J. Freitas Hybrid-Trefftz Finite Element Models for Bounded and Unbounded Elastodynamic Problems.................................................................. 400
(ID-2246)
P. Rozycki, E. Bechet, N. Möes Explicit Dynamic with X-FEM to Handle Complex Geometries............ 401
(ID-2010)
L. Stankovíc, J. Mosler Prediction of Macroscopic Material Failure Based on Microscopic Cohesive Laws .................................................................................................... 402
(ID-1255)
Table of Contents xxxvii
MS.24 Error Analysis and Adaptivity Organizers: Wiberg, N. E., Moitinho de Almeida, J., Diez, P.
L. Chamoin, P. Ladevèze (ID-2111) Strict, Sharp and Practical Bounds of Computed Outputs of Interest for Evolution Problems........................................................................... 403 É. Florentin, P. Ladevèze, J. Bellec Error Bounds on Outputs of Interest for Linear Stochastic Problems.............................................................................................................. 404
(ID-2299)
M. Jasinski, G. Zboinski An Hp-Adaptive Analysis of Some Linear Free Vibration Problems.............................................................................................................. 405
(ID-1313)
H. Lane, P. Kettil, N. Wiberg Moving Mesh Adaptivity Applied to Railway Dynamics ....................... 406
(ID-2373)
J. Mosler, M. Ortiz Finite Strain R-Adaption Based on a Fully Variational Framework ....... 407
(ID-1254)
E. Rank, V. Nübel, A. Düster Extension Processes, Adaptivity and Remeshing for Elasto-Plastic Problems.............................................................................................................. 408
(ID-2351)
J. Ródenas, J. Albelda, C. Corral, J. Mas Efficient Implementation of Domain Decomposition Methods Using a Hierarchical H-Adaptive Finite Element Program ................................. 409
(ID-2107)
W. Wall, T. Erhart, E. Ramm Adaptive Remeshing in Transient Impact Processes with Large Deformations and Nonlinear Material Behavior ................................................. 410
(ID-2615)
MS.25 Evolutionary Methods for Design Organizers: Periaux, J.
B. Bochenek, P. Forys (ID-1826) Particle Swarms in Engineering Design Problems .................................. 411 E. Campana, G. Fasano, D. Peri, A. Pinto Particle Swarm Optimization: Efficient Globally Convergent Modifications....................................................................................................... 412
(ID-2025)
G. Dulikravich, I. Egorov, N. Jelisavcic Evolutionary Optimization of Chemistry of Bulk Metallic Glasses........ 413
(ID-2228)
T. Naskar Introduction of Control Points in Splines for Synthesis of Optimized Cam Motion Programme ................................................................... 414
(ID-1576)
xxxviii Table of Contents
G. Oliveira, S. Saramago, P. Oliveira (ID-1837) On the Use of Differential Evolution in the Trajectory Modeling of Parallel Architecture Robot............................................................................. 415 M. Teixeira, M. Brandão Evolutionary Topologic Optimization Using the Finite Element Method ................................................................................................................ 416
(ID-2327)
MS.27 Fluid-Structure Interactions Organizers: Idelsohn S.
E. Aulisa, S. Manservisi, P. Seshaiyer (ID-1566) A Multilevel Domain Decomposition Methodology for Solving Coupled Problems in Fluid-Structure-Thermal Interaction ................................. 417 A. Boer, M. Schoot, H. Bijl Moving Mesh Algorithm for Unstructured Grids Based on Interpolation with Radial Basis Functions........................................................... 418
(ID-1781)
F. Daneshmand, S. Niroomandi Vibrational Analysis of Fluid-Structure Systems Using Natural Neighbour Galerkin Method................................................................................ 419
(ID-2310)
A. Kraker, D. Rixen, R. Ostayen Fluid-Structure Interaction in FEM Journal Bearing Simulations........... 420
(ID-1923)
A. Kupzok, R. Wüchner, K. Bletzinger Numerical Simulation of Wind-Structure Interaction for Thin Shells and Membranes......................................................................................... 421
(ID-1109)
J. Li, H. Chen, J. Chen Reliability Analysis of Prestressed Egg-Shaped Digester ....................... 422
(ID-1119)
P. Matyushin, V. Gushchin The Vortex Structures in the Sphere Wakes in the Wide Range of the Reynolds and Froude Numbers ..................................................................... 423
(ID-1303)
R. Niesner, M. Haupt, P. Horst Transient Analysis Methods for Hypersonic Applications with Thermo-Mechanical Fluid-Structure Interaction ................................................. 424
(ID-1965)
S. Sarkar, H. Bijl Stall Induced Vibration & Flutter in a Symmetric Airfoil....................... 425
(ID-1520)
R. Unger, M. Haupt, P. Horst Application of Lagrange Multipliers for Computational Aeroelasticity....................................................................................................... 426
(ID-1946)
Table of Contents xxxix
MS.28 Fracture and Fatigue Mechanics Organizers: Karihaloo, B.
J. Assis, V. Monine, S. Filippov, S. Iglesias (ID-1717) Computer Simulation of Diffraction Technique Applied for Measurements of Surface Stress Gradients ......................................................... 427 K. Enakoutsa, J. Leblond, G. Perrin Numerical Assessment of a Micromorphic Model of Ductile Rupture ................................................................................................................ 428
(ID-2408)
H. Hosseini-Toudeshky, B. Mohammadi, S. Bakhshandeh Fatigue Crack Trajectory Analysis of Single-Side Repaired Thin Aluminum Panels with Various Composite Patch Lay-Up Configurations ........ 429
(ID-1555)
S. Jog, R. Baddam Prediction of the Crack Initiation Life of Turbine Blade ........................ 430
(ID-1120)
M. Khoshravan, A. Hamidi Numerical Analysis of the Influence of Location of the Stopping Holes and Their Diameter in the Crack Growth of Ductile Metals ..................... 431
(ID-2240)
M. Kopecky Computed Analysis to Determine Service Life Criteria of Special Elements and Applications .................................................................................. 432
(ID-1110)
T. Luther, C. Könke Analysis of Crack Initiation and Propagation in Polycrystalline Meso and Microstructures of Metal Materials..................................................... 433
(ID-1796)
E. Szymczyk, A. Derewonko, J. Jachimowicz (ID-1669) Analysis of Displacement and Stress Distributions in Riveted Joints.................................................................................................................... 434 MS.29 Genetic Algorithms Organizers: António, C.
C. António (ID-2124) The Synergetic Effects of Hybrid Crossover Operators in Structural Optimisation ....................................................................................... 435 G. Bugeda, J. Ródenas, E. Pahl, E. Oñate An Adaptive Mesh Generation Strategy for the Solution of Structural Shape Optimization Problems Using Evolutionary Methods ............. 436
(ID-2428)
J. Dias, R. Corrêa Multiobjective Optimization of Multibody Systems with Genetic Algorithms........................................................................................................... 437
(ID-2472)
xl
Table of Contents
L. Iuspa, V. Minutolo, E. Ruocco (ID-2064) Buckling Optimization of Grid Structures Via Genetic Algorithms ....... 438 D. Kim, Y. Kim Multiscale Multiresolution Genetic Algorithm Using Diverse Population Groups............................................................................................... 439
(ID-1740)
P. Montrull, O. Querin, C. Gomez An Adaptive Correction Function for Structural Optimization with Genetic Algorithms ............................................................................................. 440
(ID-2450)
L. Sousa, C. Castro, C. António Optimization of the Topology of Masonry Units From the Thermal Point of View Using a Genetic Algorithm ............................................ 441
(ID-2292)
M. Victoria, P. Marti Topology Optimization of Bidimensional Continuum Structures by Genetic Algorithms and Stress Iso-Lines ....................................................... 442
(ID-2452)
MS.31 Impact and Control Organizers: Holnicki-Szulc, J.
I. Ario, P. Pawlowski, J. Holnicki-Szulc (ID-1476) Dynamic Analysis of Folding Patterns for Multi-Folding Structures............................................................................................................. 443 J. Cardoso, P. Moita, A. Valido Mechanical Systems Design and Control Optimization with Varying Time Domain......................................................................................... 444
(ID-2627)
S. Pashah, E. Jacquelin, J. Lainé, M. Massenzio Modelling for the Determination of the Interaction Force of Impacted Structures ............................................................................................. 445
(ID-1750)
MS.33 Intelligent Computing in Solid and Structural Mechanics Organizers: Burczynski, T.
W. Beluch (ID-1812) Evolutionary Identification and Optimization of Composite Structures............................................................................................................. 446 A. Dlugosz Parallel Evolutionary Optimization of Heat Radiators by Using MSC MARC/MENTAT Software....................................................................... 447
(ID-1853)
G. Dziatkiewicz, P. Fedelinski Evolutionary Algorithm and Boundary Element Method for Solving Inverse Problems of Piezoelectricity...................................................... 448
(ID-1930)
Table of Contents
xli
W. Kus Evolutionary Optimization of Preform and Die Shape in Forging Using Computational Grid .................................................................................. 449
(ID-1813)
W. Kus, T. Burczynski Optimization of Mechanical Structures Using Serial and Parallel Artificial Immune Systems.................................................................................. 450
(ID-1918)
P. Nazarko, L. Ziemianski Experiments of Damage Detection in Strips Based on Soft Computing Methods and Wave Propagation....................................................... 451
(ID-2581)
P. Orantek The Optimization and Identification Problems of Structures with Fuzzy Parameters ................................................................................................ 452
(ID-1811)
A. Poteralski Topology Optimization of the 3-D Structures for Various Criteria Using Evolutionary Algorithm ............................................................................ 453
(ID-1818)
A. Skrobol, T. Burczynski Computational Intelligence System in Non-Destructive Identification of Internal Defects......................................................................... 454
(ID-1816)
M. Szczepanik Optimization of Topology and Stiffeners Locations in 2-D Structures Using Evolutionary Methods.............................................................. 455
(ID-1825)
N. Wang, K. Tai A Structural Optimization Problem Formulation for Design of Compliant Gripper Using a Genetic Algorithm................................................... 456
(ID-2638)
MS.34 Intelligent Optimization Organizers: Sousa, J. C.
R. Almeida, S. Vieira, J. Sousa, U. Kaymak (ID-2061) The Prediction of Bankruptcy Using Weighted Fuzzy Classifiers.......... 457 P. Pinto, T. Runkler, J. Sousa Optimization of a Logistic Process by Ant Colonies, Wasp Swarms and Genetic Post-Optimization.............................................................. 458
(ID-1128)
S. Sakata, F. Ashida, M. Zako Kriging-Based Estimation with Noisy Data ............................................ 459
(ID-1735)
C. Silva, J. Faria, D. Naso Distributed Optimization Using ACO for Concrete Delivery ................. 460
(ID-1894)
F. Viana, G. Kotinda, V. Steffen Tuning a Vibrating Blade Dynamic Vibration Absorber by Using Ant Colony Optimization and Finite Element Modeling..................................... 461
(ID-1100)
xlii
Table of Contents
MS.35 Interrelation of Numerical and Asymptotical Approaches in Solid and Structural Mechanics Organizers: Manevitch, L., Lamarque, C. H.
C. Lamarque, E. Gourdon (ID-2579) Energy Pumping of Systems Connected to a Nonlinear Energy Sink Device ......................................................................................................... 462 V. Lyakh, V. Meleshko Stress Analysis of Curved Elastic Bar and Elastic Wedge Under Bending Load; Infinite Systems and Asymptotic ................................................ 463
(ID-1712)
A. Potapov, I. Miloserdova, I. Potapov Nonlinear Oscillations in Discretely Continual System .......................... 464
(ID-1672)
F. Romeo, G. Rega Propagation Properties of Bi-Coupled Nonlinear Oscillatory Chains.................................................................................................................. 465
(ID-1519)
MS.36 Inverse Engineering Organizers: Dulikravich, G. S., Orlande, H.
S. Abboudi, E. Artioukhine (ID-2202) Numerical Analysis of the Estimation of Three Boundary Conditions in Two Dimensional Inverse Heat Conduction Problem................... 466 J. Auzins, S. Ruchevskis, R. Rikards, A. Chate Metamodeling for the Identification of Composite Material Properties............................................................................................................. 467
(ID-2037)
T. Baranger, S. Andrieux An Energy Approach for a Cauchy Problem in Elasticity....................... 468
(ID-2062)
R. Fedele, G. Maier, L. Marazza Flat-Jack Tests and Parameter Identification for Diagnostic Analysis of Dams ................................................................................................ 469
(ID-1955)
H. Gualous, D. Zibret, E. Artioukhine Convective Boiling in Mini-Channels: Flow Visualization and Inverse Thermal Characterization ....................................................................... 470
(ID-2693)
E. Katamine, H. Azegami, M. Hirai Solution of Shape Identification Problem on Thermoelastic Solids........ 471
(ID-1716)
L. Lage, A. Cuco, F. Folly, F. Soeiro, A. Neto Stochastic and Hybrid Methods for the Solution of an Inverse Mass Transfer Problem........................................................................................ 472
(ID-2437)
P. Masson, S. Rouquette, T. Loulou, E. Artioukhine Inverse Heat Conduction Problem: Estimation of a Source Term for an Electron Beam Welding; Theoretical and Experimental........................... 473
(ID-1346)
Table of Contents
xliii
H. Nakamura, M. Kawahara (ID-1829) The Parameter Identification of Elastic Modulus at Futatsuishi Site....................................................................................................................... 474 K. Ogura, M. Kawahara Parameter Identification of the Attenuation Using First Order Adjoint Method ................................................................................................... 475
(ID-1819)
K. Sassi, S. Andrieux Parameters Identification of a Nonlinear Viscoelastic Model Via an Energy Error Functional ................................................................................. 476
(ID-1292)
F. Soeiro, A. Neto Inverse Radiative Transfer Problems in Two-Layer Participating Media................................................................................................................... 477
(ID-2435)
N. Thomson, H. Orlande Computation of Sensitivity Coefficients and Estimation of Thermophysical Properties with the Line Heat Source Method.......................... 478
(ID-1026)
H. Velho, S. Sambatti, L. Chiwiacowsky Combining a Parallel Genetic Algorithm with Variational Approach for Assessing Structural Damage........................................................ 479
(ID-1558)
MS.37 Large Scale Shape and Topology Optimization Organizers: Pedersen, P., Bendsoe, M., Sigmund O.
M. Abdalla, S. Setoodeh, Z. Gurdal (ID-1621) Design of Variable-Stiffness Composite Panels for Maximum Buckling Load ..................................................................................................... 480 G. Cheng, L. Liu, J. Yan Optimum Structure with Homogeneous Optimum Truss-Like Material ............................................................................................................... 481
(ID-1722)
P. Clausen, C. Pedersen Non-Parametric Large Scale Structural Optimization............................. 482
(ID-2583)
A. Diaz, R. Mukherjee Optimal Joint Placement and Modal Disparity in Control of Flexible Structures............................................................................................... 483
(ID-1708)
A. Gersborg-Hansen Topology Optimization of 3D Stokes Flow Problems ............................ 484
(ID-1157)
J. Jensen Efficient Optimization of Dynamic Systems Using Pade Approximants ...................................................................................................... 485
(ID-1800)
xliv
Table of Contents
M. Kim, G. Jang, Y. Kim (ID-1743) Ground Structure Based Joint Stiffness Controlling Method for Joint Compliant Mechanism Design.................................................................... 486 S. Lambert, E. Pagnacco, L. Khalij, A. Hami Topology Optimization of Structures Subject to Random Excitations with Fatigue Life Constraints ........................................................... 487
(ID-2099)
E. Lemaire, P. Duysinx, V. Rochus, J. Golinval Improvement of Pull-In Voltage of Electromechanical Microbeams Using Topology Optimization ........................................................ 488
(ID-2065)
E. Lund Large Scale Optimization of Compression Loaded Composite Structures............................................................................................................. 489
(ID-1879)
C. Narváez, A. Tovar, D. Garzon Topology Synthesis of Compliant Mechanisms Using the Hybrid Cellular Automaton Method with an Efficient Mass Control STR ..................... 490
(ID-2215)
N. Olhoff, J. Du Topological Design for Minimum Sound Radiation From Structures Subjected to Forced Vibration............................................................ 491
(ID-1792)
P. Pedersen Aspects of 3D Shape and Topology Optimization with Multiple Load Cases .......................................................................................................... 492
(ID-1250)
N. Pedersen On Shape, Material and Orientational Design of Plates in Relation to Dynamics......................................................................................................... 493
(ID-1910)
N. Perchikov, M. Fuchs Optimal Layouts of Stiffeners for Plates in Bending - Topology Optimization Approach ....................................................................................... 494
(ID-1678)
U. Schramm How Topology Optimization Changed the Design Process .................... 495
(ID-2156)
Y. Sia, O. Querin Structural Shape Optimisation by Using Multi-Direction Boundary Points Movement Method................................................................... 496
(ID-1141)
O. Sigmund On Topology Optimization with Manufacturing Constraints.................. 497
(ID-1895)
K. Svanberg, M. Werme Sequential Integer Programming Methods for Stress-Constrained Shape and Topology Optimization ...................................................................... 498
(ID-1769)
Table of Contents
xlv
A. Tovar, W. Quevedo, N. Patel, J. Renaud (ID-2185) Topology Optimization with Stress and Displacement Constraints Using the Hybrid Cellular Automaton Method ................................................... 499 G. Yoon, J. Jensen, O. Sigmund Topological Design of Acoustic-Structure Interaction Structures with the Mixed Finite Element Method............................................................... 500
(ID-2008)
MS.38 Composite Molding-Numerical Simulations and Applications Organizers: Dimitrovova, Z., Bassir, D.
N. Abdelkader, Y. Chevalier, S. Aguib, N. Chikh (ID-2643) Cinematique Influence on the Vibrations of Stratified Plates ................. 501 D. Bassir, W. Zhang, S. Guessasma Optimization of Resign Transfer Molding Process by a Virtual Manufacturing and a Genetic Algorithms ........................................................... 502
(ID-1604)
Z. Dimitrovova Post-Processing Techniques Suitability for Mesolevel Free Boundary Flows .................................................................................................. 503
(ID-2335)
M. Nossek, M. Sauer, K. Thoma Adaptive Simulation of Cohesive Interface Debonding for Crash and Impact Analyses............................................................................................ 504
(ID-1942)
S. Shigehisa, Y. Miyata, H. Ochiai Failure Analysis of Cement-Treated Soil by FEM Implemented with Particle Discretization ................................................................................. 505
(ID-2454)
A. Zoheir, T. Nabil, R. Ayad, A. Samir, B. Malek An Homogenisation Procedure for Cardboard and Stitched Sandwiches Using Respectively Analytical and Numerical Simulation ............. 506
(ID-2551)
MS.39 Material Models for Composites at Different Length Scales Organizers: Rolfes, R.
D. Ballhause, M. König, B. Kröplin (ID-1489) Modelling of Woven Fabrics with the Discrete Element Method........... 507 M. Böl, S. Reese A New Approach for the Simulation of Damage Effects in Rubber-Like Materials Using Chain Statistics .................................................... 508
(ID-1441)
L. Gornet, S. Marguet, G. Marckmann Numerical Modelling of Nomex® Honeycomb Cores : Failure and Effective Elastic Properties........................................................................... 509
(ID-2066)
xlvi
Table of Contents
G. Haasemann, M. Kästner, V. Ulbricht (ID-2024) Multi-Scale Modelling and Simulation of Textile Reinforced Materials.............................................................................................................. 510 L. Kaczmarczyk, Z. Waszczyszyn Enforcing Boundary Conditions in Micro-Macro Transition for Second Order Continuum .................................................................................... 511
(ID-2562)
M. Klüppel, J. Meier, M. Ramspeck Micro-Structure Based Modeling of Elastomer Materials ...................... 512
(ID-1511)
F. Lipperman, M. Ryvkin, M. Fuchs Analysis and Effective Properties of Honeycombs with NonSymmetric Unit Cells .......................................................................................... 513
(ID-1802)
M. Luxner, J. Stampfl, A. Woesz, P. Fratzl, H. Pettermann Influence of Defects and Perturbations on the Performance of 3D Open Cell Structures ........................................................................................... 514
(ID-1752)
A. Muhr Mechanics of Elastometer-Shim Laminates............................................ 515
(ID-2012)
J. Skocek, J. Zeman, M. Šejnoha Application of the Mori-Tanaka Method to Analysis of Woven Composites with Imperfections ........................................................................... 516
(ID-1636)
S. Smaoui, B. Abelwahed, D. Irini, D. Hélène An Homogenization Iterative Process for Nonlinear Materials Applied to Compacted Clays............................................................................... 517
(ID-2241)
M. Timmel, M. Kaliske, S. Kolling, R. Mueller A Micromechanical Approach for the Simulation of Rubberlike Materials with Damage........................................................................................ 518
(ID-1938)
W. Wajda, H. Paul Influence of Grains Misorientation on Material Hardening on Example of Aluminum Bicrystals Deformed in Channel Die ............................. 519
(ID-2544)
MS.40 Meshless Methods Organizers: Alves, C.
C. Alves, P. Antunes (ID-2532) The Method of Fundamental Solutions Applied to the Calculation of Eigensolutions for Simply Connected Plates .................................................. 520 C. Alves, S. Valtchev Comparison Between Meshfree and Boundary Element Methods Applied to BVPS in Domains with Corners ........................................................ 521
(ID-2558)
Table of Contents
xlvii
C. Alves, N. Martins (ID-2618) The Method of Fundamental Solutions Applied to a Heat Conduction Inverse Problem ............................................................................... 522 M. Arroyo, M. Ortiz Local Maximum-Entropy Approximation Schemes................................ 523
(ID-1540)
J. Belinha, L. Dinis Analysis of 2D Problems Resorting to a New Meshless Method............ 524
(ID-1935)
M. Bitaraf, S. Mohammadi Solving the Chloride Diffusion Equation in Concrete Structures for Prediction of Initiation Time of Corrosion .................................................... 525
(ID-1887)
S. Chantasiriwan Solution of the Stationary Three-Dimensional Navier-Stokes Equations by Using Radial Basis Functions........................................................ 526
(ID-1732)
T. Most, C. Bucher An Enhanced Moving Least Squares Interpolation for the Element-Free Galerkin Method ........................................................................... 527
(ID-1233)
H. Netuzhylov Enforcement of Boundary Conditions in Meshfree Methods Using Interpolating Moving Least Squares.................................................................... 528
(ID-1969)
V. Rosca, V. Leitão A Simple and Less-Costly Integration of Meshless Galerkin Weak Form .................................................................................................................... 529
(ID-2574)
C. Tiago, P. Pimenta Geometrically Exact Analysis of Shells by a Meshless Approach.......... 530
(ID-2159)
O. Valencia, F. Gómez-Escalonilla, F. Urbinati, J. López-Díez Weight Functions Analysis in Elastostatic Problems for Meshless Element Free Galerkin Method ........................................................................... 531
(ID-2398)
MS.41 Metal Forming Organizers: Cesar Sá, J., Pietrzyk, M.
F. Abbassi, O. Pantale, A. Zghal, R. Rakotomalala (ID-1575) Prediction of Sheet Metal Formability (FLD) by Using Diverse Method ................................................................................................................ 532 J. Alves, M. Oliveira, L. Menezes Modeling Drawbeads in Deep Drawing Simulations .............................. 533
(ID-1848)
S. Benke, G. Laschet On a 2-Phase Finite Element Model for the Coherent Mushy Zone in Casting Applications ....................................................................................... 534
(ID-1501)
xlviii Table of Contents
H. Christophe, A. Said, D. Loic (ID-1588) Modeling of Ductile Behavior of Metals Under a Wide Range of Loading Rates: Semi-Empirical Approach.......................................................... 535 S. Ding, B. Daniel, P. Meehan A New Relaxation Method for Roll Forming Problems.......................... 536
(ID-1362)
M. Glowacki, M. Hojny Computer Modelling of Deformation of Steel Samples with Mushy Zone......................................................................................................... 537
(ID-1753)
B. Haddag, F. Abed-Meraim, T. Balan Prediction of Strain Localisation in Forming Process Using Advanced Elastic-Plastic Behaviour Models Coupled with Damage.................. 538
(ID-2055)
R. Jorge, A. Roque, M. Parente, A. Fernandes, R. Valente Symulation of Hydroforming on Tailor-Welded Tubular Blanks Using Solid-Shell Finite Elements ...................................................................... 539
(ID-1988)
T. Lelotte, L. Duchêne, A. Habraken Fast Method to Predict an Earing Profile Based on Lankford's Coefficients and Yield Locus .............................................................................. 540
(ID-2402)
L. Madej, A. Zmudzki, P. Hodgson, M. Pietrzyk Possibilities of Application of the Multi Scale Strain Localization Café ..................................................................................................................... 541
(ID-2231)
K. Nabil, K. Yahia Thermal Modeling of D. C. Continuous Casting Process of a AlMg Alloy ............................................................................................................. 542
(ID-1915)
J. Ponthot, R. Boman, L. Papeleux, Q. Bui A 3D Arbitrary Lagrangian Eulerian Formulation for the Numerical Simulation of Forming Processes. ..................................................... 543
(ID-2053)
M. Poursina, H. Ebrahimi, J. Parvizian A Study for the Constitutive Equations of 1.4021 and 1.4841 Stainless Steels in Hot Deformation .................................................................... 544
(ID-2503)
W. Rasp, A. Yusupov Modelling of Spread and Side-Form Function in Hot Rolling by Different Upper-Bound Approaches ................................................................... 545
(ID-2243)
J. Sá, C. Zheng Non Local Models and Length Scale Effects on Metal Forming Processes ............................................................................................................. 546
(ID-2336)
M. Salmanitehrani, M. Poursina Analysis of Thermal Cracking of an Industrial Duct Using Finite Element Simulation ............................................................................................. 547
(ID-2500)
Table of Contents
xlix
M. Schwarze, S. Reese (ID-2393) Analysis of Forming Processes with Efficient Finite Element Procedures ........................................................................................................... 548 P. Teixeira, F. Pires, A. Santos, J. Sá Numerical Investigation of Fracture Onset in Sheet Metal Forming ............................................................................................................... 549
(ID-2413)
MS.42 Modeling in Mechanobiology Organizers: Lekszycki, T.
A. Andreykiv, F. Keulen (ID-2446) Effect of Surface Geometry and Local Mechanical Environment on Periimplant Tissue Differentiation:A Finite Element Study........................... 550 C. Bonifasi-Lista, E. Cherkaev Identification of Bone Structure From Effective Measurements............. 551
(ID-2190)
M. Cioffi, F. Galbusera, M. Raimondi, F. Boschetti, G. Dubini Computational Modeling of Mechanical Environment Within Tissue Engineered Cartilage................................................................................ 552
(ID-1868)
H. Kim, P. Clement, J. Cunningham Stress-Based Optimum and Bone Architecture....................................... 553
(ID-2340)
P. Kowalczyk Parameterized Orthotropic Cellular Microstructures As Mechanical Models of Cancellous Bone ............................................................. 554
(ID-1151)
M. Nowak Modeling of Cancellous Bone Surface Adaptation Based on the 3Dimensional Trabeculae Topology Evolution.................................................... 555
(ID-1004)
J. Pierre, C. Oddou Theoretical Analysis of the Remodeling Processes in Bony Tissue Engineered Implants............................................................................................ 556
(ID-2294)
G. Sciarra, T. Lekszycki Bone Remodeling Description Based on Micro Mechanical/Biological Effects ............................................................................ 557
(ID-1768)
MS.43 Modelling of Functionally graded materials and structures Organizers: Batra, R., Ferreira, A.
L. Aebi, J. Vollmann, J. Dual (ID-1497) Two-Dimensional Elastodynamic Wave Propagation in Graded Structures............................................................................................................. 558
l
Table of Contents
H. Argeso, A. Eraslan (ID-1184) A Computational Study on Functionally Graded Rotating Solid Shafts: Analysis of Preliminary Results .............................................................. 559 R. Batra, J. Xiao, D. Gilhooley, M. Mccarthy, J. Gillespie Static Analysis of Thick Functionally Graded Plates by Using a Higher-Order Shear and Normal Deformable Plate Theory ................................ 560
(ID-2013)
M. Bocciarelli, G. Bolzon, G. Maier Three-Point-Bending and Indentation Tests for the Calibration of Functionally Graded Material Models by Inverse Analysis ................................ 561
(ID-1747)
A. Ferreira, G. Fasshauer, C. Roque, R. Jorge Static Deformations and Natural Frequencies of Functionally Graded Plates by a Hybrid Meshless Method...................................................... 562
(ID-1339)
S. Hamza-Cherif, A. Houmat, A. Hadjoui Graded Fourier P-Element Calculation of Steady State Heat Conduction in Functionally Graded Materials .................................................... 563
(ID-1111)
T. Nguyen, K. Sab, G. Bonnet A Reissner-Mindlin Plate Model for Functionally Graded Materials.............................................................................................................. 564
(ID-2254)
W. Szymezyk A Review of the Chosen Problems of FEM Modeling of Surface Coatings............................................................................................................... 565
(ID-1823)
MS.44 Multibody Dynamics Organizers: Ambrósio, J.
C. Bottasso, D. Dopico, L. Trainelli (ID-1764) On the Optimal Scaling of Index Three DAEs in Multibody Dynamics............................................................................................................. 566 S. Breun, R. Callies Redundant Optimal Control of Manipulators Along Specified Paths .................................................................................................................... 567
(ID-1874)
M. Ebbesen, M. Hansen, T. Andersen Optimal Tool Point Control of Hydraulically Actuated Flexible Multibody System with an Operator-In-The-Loop.............................................. 568
(ID-2433)
D. Franitza, T. Lichtneckert Slim Elastic Structures with Transversal Isotropic Material Properties Under Finite Deformations................................................................. 569
(ID-2281)
M. Hajzman, P. Polach Modelling of Flexible Rods Falling in Fluid with Possible Contacts............................................................................................................... 570
(ID-1912)
Table of Contents
li
H. Irschik, M. Nader, C. Zehetner (ID-1934) Tracking of Displacements in Smart Elastic Beams Subjected to Rigid Body Motions ............................................................................................ 571 E. Lens, A. Cardona Dynamic Analysis of Constrained Nonlinear Multibody Systems with Intermittent Contact..................................................................................... 572
(ID-2509)
D. Leshchenko, L. Akulenko, S. Suksova Evolution of Rotation of a Triaxial Satellite Under the Action of Gravitational and Light Pressure Torques ........................................................... 573
(ID-1085)
S. Leyendecker, P. Betsch, P. Steinmann Mechanical Integrators for Nonlinear Flexible Multibody Dynamics............................................................................................................. 574
(ID-2309)
K. Lipinski Some Really Simple But Useful Model of Substitutable Elasticity Modelled As Elasticity in Six Subsequent Joints ................................................ 575
(ID-1757)
K. Lipinski Optimal Dampers Localization for a Body Under Double Load and the Body Behaviour for Some Intermediate Loads....................................... 576
(ID-1758)
P. Polach, M. Hajzman Design of Characteristics of Air Pressure Controlled Hydraulic Shock Absorbers in an Intercity Bus ................................................................... 577
(ID-1860)
R. Santos, V. Steffen, S. Saramago Robot Path Planning in a Constrained Workspace by Using Optimal Control Techniques ............................................................................... 578
(ID-1628)
G. Schanzer, R. Callies Optimal Control of Multi-Link Manipulators with Rivalling Actuators ............................................................................................................. 579
(ID-1771)
L. Sousa, P. Verissimo, J. Ambrósio Development of Validated Generic Road Vehicles for Crashworthiness Through Optimization Procedures ........................................... 580
(ID-2363)
M. Szczotka, I. Adamiec-Wójcik, S. Wojciech Developing Mathematical and Computer Models for Car Dynamics Using Joint Co-Ordinates and Homogenous Transformations ........... 581
(ID-1577)
MS.45 Multiphysics Modelling in Geomechanics Organizers: Borja, R. I., Montáns, F.J., Tamagnini, C.
J. Andrade, R. Borja (ID-1563) Finite Element Simulation of Deformation Bands in Saturated Granular Media with Inhomogeneous Porosities at the Meso-Scale ................... 582
lii
Table of Contents
M. Caminero, F. Montáns (ID-1700) Computational Framework for Multilayer Plasticity Based on Critical State Soil Mechanics .............................................................................. 583 L. Hu, T. Hueckel Creep of Geomaterials Due to Coupled Damage and Spontaneous Mineral Dissolution............................................................................................. 584
(ID-2222)
R. Kohler, G. Hofstetter Validation of an Extended Cap Model for Partially Saturated Soils ....... 585
(ID-1257)
A. Mesgouez, G. Lefeuve-Mesgouez, A. Chambarel Partially Saturated Porous Medium Vibration Induced by an Impulsional Load................................................................................................. 586
(ID-1964)
M. Murad, C. Moyne Macroscopic Behavior of Smectitic Clays Derived From Nanostructure ...................................................................................................... 587
(ID-1103)
P. Rehermann, R. Borja, D. Pollard Mechanical Modeling of Multi-Layer Sedimentary Rock Folding ......... 588
(ID-1567)
D. Souza, A. Coutinho, J. Alves Fast Numerical Simulation of Porous Media Flows................................ 589
(ID-1536)
MS.46 Multiscale Mechanics of Biological Materials and Other Natural Composites Organizers: Hellmich, C.
F. Genna (ID-1129) A Micromechanically-Based Interface Model for the Periodontal Ligament.............................................................................................................. 590 Q. Grimal, K. Raum, P. Laugier Computation of Cortical Bone Macroscopic Properties From Microscopic Elastic Data..................................................................................... 591
(ID-1300)
R. Grytz, G. Meschke Computational Homogenization in Multi-Scale Shell Analysis at Large Strains........................................................................................................ 592
(ID-1238)
D. Katti, P. Ghosh, K. Katti Mineral Proximity Influences Protein Unfolding: a Molecular Dynamics Study .................................................................................................. 593
(ID-1998)
K. Katti, R. Bhowmik, D. Katti, D. Verma Modeling the Role of Interfaces on Mechanical Response in Composite Bone Biomaterials ............................................................................. 594
(ID-2018)
Table of Contents
liii
P. Laugier (ID-2022) Finite-Difference Computations of Ultrasound Wave Propagation in Bone ................................................................................................................ 595 F. Moravec, M. Muller Microstructural Model of the Viscoelastic Behaviour of Biological Tissues ............................................................................................... 596
(ID-1815)
K. Okumura Scaling Views on Strength of Soft/Hard Composites ............................ 597
(ID-2501)
MS.47 Multiscale Method for Structural Non-Linear and Dynamic Problems Organizers: Allix, O., Rey, C.
A. Amini, D. Dureisseix, P. Cartraud, N. Buannic (ID-1310) A Micro-Macro Strategy for Ship Structural Analysis with FETIDP Method .......................................................................................................... 598 E. Baranger, O. Allix, L. Blanchard On the Use of Fourier Expansions for the Simulation of Elastic Composite Pipes with Defects............................................................................. 599
(ID-2550)
B. Bourel, A. Combescure, L. Valentin A Multigrid Approach for Non-Linear Structural Analysis in Explicit Dynamics ............................................................................................... 600
(ID-2647)
V. Carvelli, C. Corazza, C. Poggi Mechanical Behaviour of Textile Structures: Two-Scales Approach ............................................................................................................. 601
(ID-1336)
P. Cresta, O. Allix, C. Rey, S. Guinard On Multilevel Strategies for Nonlinear Computations with Domain Decomposition: Application to Post-Buckling ...................................... 602
(ID-2138)
M. Kuprys, R. Barauskas Textile Fabric Simulator: Collisions Handling at the Level of Yarns ................................................................................................................... 603
(ID-1839)
J. Pebrel, P. Gosselet, C. Rey A Computational Strategy for Contact Simulation.................................. 604
(ID-2345)
C. Rickelt, S. Reese A Simulation Strategy for Life Time Calculations of Large, Partially Damaged Structures .............................................................................. 605
(ID-2361)
Y. Shiihara, O. Kuwazuru, N. Yoshikawa Finite Element Method in First-Principles Calculation........................... 606
(ID-2355)
liv
Table of Contents
M. Spiridonakos, S. Fassois (ID-1840) Modelling and Simulation of Earthquake Ground Motion Via Functional Series TARMA Models with Wavelet Basis Functions .................... 607 MS.48 Neural Networks and Soft Computing in Solid and Structural Mechanics Organizers: Waszczyszyn, Z.
A. Borowiec, L. Ziemianski (ID-2582) Identification of Damage in Multispan Beams Using ParameterDependent Frequency Changes and Neural Networks ........................................ 608 A. Kucerova, M. Leps, J. Zeman Microplane Model Parameters Estimation Using Neural Networks ....... 609
(ID-1992)
K. Kuzniar Anns and Linguistic Variables in the Analysis of Mine Induced Rockbursts Transmission to the High Building................................................... 610
(ID-2592)
W. Lu, L. Duan, F. Mora-Camino, R. Faye Differential Flatness of Aircraft Flight Dynamics and Neural Inversion.............................................................................................................. 611
(ID-1591)
MS.49 Nonlinear Dynamics of Moving Structures Organizers: Zahariev, E., Mayo Nunez, J.
A. Ayestarán, C. Graciano (ID-2635) Finite Element Analysis of an Energy Absorbing Crush Zone Using Expanded Metal ........................................................................................ 612 L. Desouza Design of Satellite Control System Using the Optimal Nonlinear Theory ................................................................................................................. 613
(ID-1017)
J. Dias, F. Antunes, M. Pereira Design for Crashworthiness of Train Structures with Simplified Multibody Models ............................................................................................... 614
(ID-2499)
J. Gerstmayr, M. Matikainen Analysis of Stress and Strain in the Absolute Nodal Coordinate Formulation with Nonlinear Material Behavior .................................................. 615
(ID-2612)
S. Hornstein, O. Gottlieb Nonlinear Multimode Dynamics of a Moving Microbeam for Noncontacting Atomic Force Microscopy........................................................... 616
(ID-1172)
Y. Lin, P. Nikravesh Model Reduction with Mean-Axes in Deformable Multibody Dynamics............................................................................................................. 617
(ID-2105)
Table of Contents
lv
J. Mayo (ID-1841) Impacts with Friction in Flexible Multibody Dynamics ......................... 618 J. Orden, R. Ortega A Conservative Augmented Lagrangian Algorithm for the Dynamics of Constrained Mechanical Systems................................................... 619
(ID-1968)
M. Piovan, R. Sampaio Non Linear Model for Coupled Axial/Torsional/Flexural Vibrations of Drill-Strings................................................................................... 620
(ID-1561)
A. Poulimenos, M. Spiridonakos, S. Fassois Identification of Time-Varying Structures Under Unobservable Excitation: an Overview and Experimental Comparison..................................... 621
(ID-1810)
I. Romero Variational Integrators for the Rigid Body Dynamics............................. 622
(ID-1961)
E. Zahariev Planning and Optimization of Maneuver Strategy of Large Flexible Space Structures .................................................................................... 623
(ID-1548)
R. Zander, H. Ulbrich Free Plain Motion of Flexible Beams in MBS - a Comparison of Models................................................................................................................. 624
(ID-1515)
MS.50 Non-Linear Vibration of Structures Organizers: Ribeiro, P.
R. Arquier, B. Cochelin (ID-2051) Numerical Computation of Non Linear Modes of Elastic Structures............................................................................................................. 625 S. Bellizzi, R. Bouc Nonlinear Modes: Amplitude-Phase Formulation and Bifurcation Analysis............................................................................................................... 626
(ID-2455)
M. Haterbouch, P. Ribeiro, R. Benamar Multi-Modal Non-Linear Free Vibration of Thin Isotropic Circular Plates ..................................................................................................... 627
(ID-1603)
M. Kireitseu, G. Tomlinson Computational Approaches to Prediction of Damping Behavior of Nanoparticle-Reinforced Coatings and Foamy Structures .................................. 628
(ID-1143)
A. Kocsis, G. Károlyi Buckling Under Conservative and Nonconservative Load ..................... 629
(ID-1531)
N. Krancevic, M. Stegic, N. Vrankovic Bifurcation of Periodic Solutions in the Two-Degree-of-Freedom System with Clearances....................................................................................... 630
(ID-1218)
lvi
Table of Contents
R. Lewandowski (ID-1873) Perturbation Method for Strongly Non-Linear Free Vibrations of Beams .................................................................................................................. 631 P. Ribeiro, B. Cochelin, S. Bellizzi Vibrations of Shallow and Deep Shells by the P-Version Finite Element Method .................................................................................................. 632
(ID-2129)
N. Srinil, G. Rega Resonant Non-Linear Dynamic Responses of Horizontal Cables Via Kinematically Non-Condensed/Condensed Modeling.................................. 633
(ID-1627)
J. Thomsen Computing Effective Properties of Nonlinear Structures Exposed to Strong High-Frequency Loading at Multiple Frequencies .............................. 634
(ID-2552)
J. Zapomel Implementation of a Vapour Cavitation Into Computational Models of Rotors Supported by Long Journal Bearings...................................... 635
(ID-1105)
MS.51 Optimization and Robust Design for Industrial-sized Problems Organizers: Bletzinger, K. U., Duddeck, F., Meyer M.
F. Duddeck (ID-1470) Multi-Criteria Optimizations and Robustness Estimations for Crashworthiness, Structural Dynamics, and Acoustics ....................................... 636 K. Grossenbacher, F. Duddeck, M. Ganser, P. Hora Process Robustness in Sheet Metal Forming by an Integrated Engineering Strategy ........................................................................................... 637
(ID-2030)
M. Hansen, T. Andersen, J. Hansen, O. Mouritsen Topology Optimization of Robots Using Mapping Techniques.............. 638
(ID-2606)
H. Müllerschön, M. Hove, B. Mlekusch Optimization Strategies for Highly Non-Linear FE-Applications As Crashworthiness Applications........................................................................ 639
(ID-2388)
M. Ohsaki Local and Global Searches of Approximate Optimal Designs of Regular Frames.................................................................................................... 640
(ID-1174)
J. Reger, T. Schneider, C. Ehlert Optimisation of Car Body Parts Regarding Equivalent Radiation Power Using a Genetic Algorithm and Morphing ............................................... 641
(ID-1596)
K. Sedlaczek, P. Eberhard Grid-Based Topology Optimization of Rigid Body Mechanisms Using Different Problem Formulations ............................................................... 642
(ID-1498)
Table of Contents
lvii
H. Wenzel (ID-1903) Combining Optimization and Robust Engineering Methods in the Engineering Product Design Process................................................................... 643 MS.56 Shape and Topological Sensitivity Analysis: Theory and Applications Organizers: Feijóo, R.., Taroco, E.
G. Allaire, F. Jouve, F. Gournay, A. Toader (ID-2691) Combining Topological and Shape Derivatives in Structural Optimization........................................................................................................ 644 F. Barthold, K. Wiechmann A Comparison of Displacement and Mixed Finite Element Formulations for Variational Design Sensitivity Analysis .................................. 645
(ID-2003)
M. Bonnet Inverse Acoustic Scattering by Small-Obstacle Expansion of Misfit Function .................................................................................................... 646
(ID-2677)
J. Faria, R. Feijóo, A. Novotny, E. Taroco, C. Padra Second Order Topological Sensitivity Analysis...................................... 647
(ID-2029)
M. Langelaar, F. Keulen Sensitivity Analysis of Shape Memory Alloy Shells .............................. 648
(ID-1905)
L. Miegroet, T. Jacobs, E. Lemaire, P. Duysinx Stress Constrained Optimization Using X-FEM and Level Set Description .......................................................................................................... 649
(ID-2026)
A. Myslinski Level Set Method for Optimization of Contact Problems ....................... 650
(ID-2067)
H. Pham, C. Bucher An Iterative Procedure for Model Updating Based on Selective Sensitivity............................................................................................................ 651
(ID-1083)
MS.57 Shell and Spatial Structures Organizers: Ramm, E.
M. Birsan (ID-1462) Extension, Bending and Torsion of Cylindrical Cosserat Shells Made From a Porous Elastic Material ................................................................. 652 N. Dung, G. Wells A Study of Discontinuous Galerkin Methods for Thin Bending Problems.............................................................................................................. 653
(ID-2449)
lviii
Table of Contents
M. Frenzel, M. Bischoff, W. Wall (ID-2611) Discrete Strain Gap (Dsg) Solid Finite Elements at Large Deformations for Non-Linear Analysis of Shells and Solids .............................. 654 E. Gal, M. Zelkha, R. Levy A Simple Co-Rotational Geometrically Non-Linear Membrane Finite Element Wrinkling Analysis ..................................................................... 655
(ID-1629)
B. Izzuddin Co-Rotational System Definitions for Large Displacement Triangular and Quadrilateral Shell Elements ...................................................... 656
(ID-1609)
P. Khosravi, R. Ganesan, R. Sedaghati Non-Linear Analysis of Composite Plates and Shells Using a New Shell Element ...................................................................................................... 657
(ID-1614)
J. Mäkinen, H. Marjamäki Total and Updated Lagrangian Geometrically Exact Beam Elements .............................................................................................................. 658
(ID-1683)
E. Maunder, B. Izzuddin Large Displacement Analysis of Plates Using Hybrid Equilibrium Elements .............................................................................................................. 659
(ID-1541)
H. Noguchi, F. Fujii, Y. Ishihara Buckling Modes of Large-Scale Shell Structures Automatically Detected From Linearized Stiffness by Iterative Solvers .................................... 660
(ID-2271)
I. Oliveira, E. Campello, P. Pimenta Finite Element Analysis of the Wrinkling of Orthotropic Membranes .......................................................................................................... 661
(ID-2415)
R. Schlebusch, B. Zastrau Theory and Numerics of a Surface-Related Shell Formulation............... 662
(ID-2284)
M. Spalatelu-Lazar, F. Léné, N. Turbé Modelling and Optimization of Sails ...................................................... 663
(ID-1989)
M. Tanaka, H. Noguchi Instability Analysis of Thin-Walled Structures Using Incompressible Hyperelastic Shell Elements....................................................... 664
(ID-2253)
MS.58 Simulation of Non-Gaussian Stochastic Processes and Fields with Applications to Structural Engineering Problems Organizers: Papadrakakis, M., Stefanou, G.
J. Cruz, M. Gutiérrez, L. Koene (ID-1206) Stochastic Simulation of Pitting Corrosion ............................................. 665
Table of Contents
lix
V. Denoël, H. Degée (ID-1227) Non Gaussian Response of Bridges Subjected to Turbulent Wind Effect of the Non Linearity of Aerodynamic Coefficients .................................. 666 M. Grigoriu Simulation of Non-Gaussian Stochastic Processes and Fields with Applications to Structural Engineering Problems ............................................... 667
(ID-1261)
N. Lagaros, G. Stefanou, M. Papadrakakis A Novel Approach for the Efficient Simulation of Highly Skewed Non-Gaussian Stochastic Fields .......................................................................... 668
(ID-1932)
M. Schevenels, G. Lombaert, G. Degrande, D. Degrauwe, B. Schoors The Wave Propagation in a Vertically Inhomogeneous Soil with a Random Dynamic Shear Modulus....................................................................... 669
(ID-1854)
G. Stefanou, M. Papadrakakis On the Karhunen-Loeve Expansion and Spectral Representation Methods for the Simulation of Gaussian Stochastic Fields ................................. 670
(ID-1940)
MS.59 Soft Tissue Organizers: Jorge, R.
J. Barbosa, R. Jorge, M. Parente, A. Fernandes, T. Mascarenhas, B. Patricio (ID-1452) Study of Mechanical Properties of Human Skin ..................................... 671 R. Basto, C. Costa, W. Pereira, M. Krüger, H. Orlande, H. Fonseca Thermophysical Properties of Different Samples of TissueMimicking Materials for Ultrasound Hyperthermia Phantoms ........................... 672
(ID-2160)
A. Cavicchi, L. Gambarotta, R. Massabò Different Computational Approaches in the Modeling of Wrinkling of Biological Membranes................................................................... 673
(ID-2426)
F. Gentil, R. Jorge, A. Ferreira, M. Parente, M. Moreira, E. Almeida Dynamic Study of the Middle Ear........................................................... 674
(ID-1496)
S. Kuzukami, N. Yoshikawa, O. Kuwazuru Image-Base Inverse Problems to Identify Three-Dimensional Displacement Field.............................................................................................. 675
(ID-1425)
P. Martins, R. Jorge, A. Ferreira, F. Gentil Experimental Study of the Middle Ear Biological Support Structures............................................................................................................. 676
(ID-1527)
T. Miyashita, H. Yamauchi, M. Inui, H. Yamakawa A Real-Time FEM Simulation for Cutting Operation Using Haptic Device.................................................................................................................. 677
(ID-2338)
lx
Table of Contents
M. Parente, R. Jorge, A. Fernandes, T. Mascarenhas, J. Martins (ID-1473) The Biomechanical Behavior of the Pelvic Floor Muscles During a Vaginal Delivery............................................................................................... 678 MS.60 Stability and Non-Linear Behaviour of Thin-Walled Members and Structures Organizers: Camotim, D.
S. Ádány, N. Silvestre, B. Schafer, D. Camotim (ID-1443) Buckling Analysis of Unbranched Thin-Walled Members: Generalised Beam Theory and Constrained Finite Strip Method ........................ 679 A. Andrade, D. Camotim, P. Costa Lateral-Torsional Buckling Analysis of Singly Symmetric WebTapered I-Beams Using Finite Elements and Finite Differences ........................ 680
(ID-1974)
J. André, A. Baptista Stability of Telescopic Props for Temporary Structures ......................... 681
(ID-1545)
C. Basaglia, D. Camotim, N. Silvestre Formulation of a GBT-Based Finite Element to Analyse the Global Buckling Behaviour of Plane/Spatial Thin-Walled Frames..................... 682
(ID-1943)
R. Bebiano, N. Silvestre, D. Camotim GBT-Based Finite Element to Analyse the Buckling Behaviour of Thin-Walled Members Subjected to Non-Uniform Bending............................... 683
(ID-2039)
N. Boissonnade, H. Degée A Non-Linear 3-D Beam Finite Element for the Study of Steel Frames with Tapered Members. .......................................................................... 684
(ID-1248)
R. Castro, J. Silva, P. Vellasco, S. Andrade, L. Lima, L. Neves Non-Linear Dynamical Response of Steel Portal Frames with Semi-Rigid Connections...................................................................................... 685
(ID-1726)
N. Chen, C. Soares Buckling Analysis of Stiffened Composite Panels.................................. 686
(ID-2002)
H. Degée, N. Boissonnade Interactive Buckling of Thin-Walled Rectangular Hollow Sections - Comparison Between Modified Beam Models and .......................................... 687
(ID-1228)
R. Degenhardt, A. Kling, K. Rohwer Design and Analysis of Composite Panels.............................................. 688
(ID-1914)
P. Dinis, D. Camotim On the Use of Shell Fea to Assess the Local Buckling & PostBuckling Behaviour of Cold-Formed Steel Thin-Walled Members.................... 689
(ID-1828)
N. Fallah A Finite Volume Method for Plate Buckling Analysis ........................... 690
(ID-1353)
Table of Contents
lxi
A. Formisano, G. Matteis, M. Maruzzelli, F. Mazzolani (ID-2517) Design of Slender Steel Shear Panels: a Numerical Study...................... 691 R. Goncalves, P. Grognec, D. Camotim Plastic Bifurcation Fea of Thin-Walled Members: Thin Shell Elements Vs. GBT-Based Beam Elements.......................................................... 692
(ID-1953)
R. Gonçalves, M. Ritto-Corrêa, D. Camotim A Large Displacement and Finite Rotation Thin-Walled Beam Finite Element Formulation................................................................................. 693
(ID-2017)
R. Goñi, E. Bayo A New Method to Assess the Rotation Capacity of Structural Hollow Sections Based in Multibody Theory ..................................................... 694
(ID-1474)
M. Haßler, K. Schweizerhof On the Stability Analysis of Thin Walled Shell Structures Containing Gas Or Fluid ..................................................................................... 695
(ID-2376)
M. Khedmati, M. Zareei Sensitivity Analysis on Ultimate Strength of Stiffened Aluminum Plates Under Combined Inplane Compression and Lateral Presuure .................. 696
(ID-2326)
H. Ovesy, S. Ghannadpour Large Deflection Behavior of Functionally Graded Plates Under Pressure Loads, Using Finite Strip Method......................................................... 697
(ID-1243)
H. Ovesy, H. Hosseini-Toudeshky, M. Kharazi Buckling Analysis of Laminates with Multiple Through-TheWidth Delaminations by Using Spring Simulated Model ................................... 698
(ID-1744)
P. Real, N. Lopes, L. Silva, C. Rebelo Numerical Validation of the Eurocode 3 Design Rules for LateralTorsional Buckling of I-Beams ........................................................................... 699
(ID-2126)
C. Rebelo, L. Silva, P. Real, N. Lopes Statistical Evaluation of the Eurocode 3 Design Rules for LateralTorsional Buckling of I-Beams ........................................................................... 700
(ID-2416)
M. Ritto-Corrêa, D. Camotim On the Interpolation of Rotations and Rigid-Body Motions in Nonlinear Beam Finite Elements......................................................................... 701
(ID-2050)
K. Rzeszut, A. Garstecki Stability of Beams and Columns Made of Thin-Walled ColdFormed Sections Accounting for Imperfections.................................................. 702
(ID-1944)
W. Schneider, M. Gettel Equivalent Geometric Imperfections for Steel Shell Structures Subject to Combined Loading ............................................................................. 703
(ID-2004)
lxii
Table of Contents
I. Shufrin, M. Eisenberger (ID-2404) Shear Buckling of Thin Plates with Constant In-Plane Stresses ............. 704 N. Silva, N. Silvestre, D. Camotim GBT Formulation to Analyse the Buckling Behaviour of Frp Composite Branched Thin-Walled Members ...................................................... 705
(ID-2282)
N. Silvestre, N. Silva On the Influence of Material Couplings on the Buckling Behaviour of FRP Thin-Walled Columns – a GBT-Based Approach ................. 706
(ID-2272)
C. Soares, R. Luís Ultimate Strength of Plate Assemblies with Localized Imperfection Subjected to Compressive Loads ................................................... 707
(ID-1948)
R. Vieira, F. Virtuoso, E. Pereira Higher Order Analysis of a Thin-Walled Beam...................................... 708
(ID-2370)
MS.61 Structural and Multidisciplinary Optimization Organizers: Herskovits, J.
M. Abolbashari, M. Majdi (ID-2387) Structural Optimization Using Optimizer Program................................. 709 D. Babkin, E. Kligman, V. Matveyenko, N. Yurlova Optimization of Dissipative Characteristics of Structures on the Basis of Problems on Natural Vibrations of Viscoelastic Solids......................... 710
(ID-1807)
K. Bhagate, P. Pawar, A. Singh, J. Ye Accuracy of Design Sensitivity Analysis for Optimization of Structures for Small Strain Theory by Finite Element Method ........................... 711
(ID-1477)
D. Bojczuk Method of Optimal Reinforcement of Structures Based on Topological Derivative........................................................................................ 712
(ID-1601)
R. Botez, A. Dinu, I. Cotoi Optimisation of Unsteady Aerodynamic Forces for Aircraft Aeroservoelastic Studies ..................................................................................... 713
(ID-1606)
R. Cadete, J. Dias, M. Pereira A Multidisciplinary Design Optimization Framework Applied to Mechanical Systems ............................................................................................ 714
(ID-2371)
A. Canelas, P. Mappa, J. Herskovits, J. Telles Shape Optimization Using the Boundary Elements and a Sand Interior Point Algorithm for Constrained Optimization ...................................... 715
(ID-2448)
P. Coelho, P. Fernandes, J. Cardoso, J. Guedes, H. Rodrigues A Three-Dimensional Hierarchical Model for Topology Optimization of Structures .................................................................................. 716
(ID-2481)
Table of Contents
lxiii
A. Csébfalvi, G. Csébfalvi (ID-2019) A New Hybrid Meta-Heuristic Method for Optimal Design of Space Trusses with Elastic-Plastic Collapse Constraints..................................... 717 B. Desmorat The Concept of Homogeneous Thermodynamical Potentials for Nonlinear Structural Rigidity Optimization ........................................................ 718
(ID-2042)
L. Desouza Satellite Attitude Control System Parameters Optimization ................... 719
(ID-1097)
V. Dubeux, J. Herskovits, S. Mazorche A Limited Memory Quasi-Newton Preconditioner for Large Scale Optimization........................................................................................................ 720
(ID-2600)
M. Ebbesen, M. Hansen, N. Pedersen Design Optimization of Conveyor Systems ............................................ 721
(ID-2001)
J. Herskovits, E. Goulart, M. Aroztegui Sparse Quasi-Newton Matrices for Large Size Optimization with FAIPA, the Feasible Arc Interior Point Algorithm.............................................. 722
(ID-1977)
S. Holopainen Sensitivity and Sizing of Nonlinear Structures Made of Anisotropic Rubber-Like Material ...................................................................... 723
(ID-1241)
L. Johansen, E. Lund Optimization of Laminated Composite Structures Using Delamination Criteria and Adaptive Models ....................................................... 724
(ID-1896)
J. Kock, C. Strauss, C. Pohl, P. Wyk, P. Botes Yeast Biomechanics ................................................................................ 725
(ID-1057)
J. Kruzelecki, M. Król Optimization of Postbuckling Path for Cylindrical Shells Under External Pressure................................................................................................. 726
(ID-2123)
R. López, A. Tovar, C. Narváez Structural Analysis in Continuum Media Using Cellular Automata ....... 727
(ID-1742)
K. Mikhail, I. Egorov, S. Yuri, F. Konstantin Multidisciplinary Optimization of Complex Technical Systems ............ 728
(ID-2211)
J. Roche Adaptive Shape Optimization Method .................................................... 729
(ID-1235)
M. Secanell, B. Carnes, A. Suleman, N. Djilali A Pem Fuel Cell Cathode Model for Gradient-Based Optimization ....... 730
(ID-1553)
I. Shevtsov, V. Markine, C. Esveld, M. Markina Optimisation of a Railway Wheel Profile ............................................... 731
(ID-1774)
lxiv
Table of Contents
J. Stegmann, M. Stolpe (ID-1861) Discrete Material Optimization of Laminated Composites - Simp Vs. Global Optimization...................................................................................... 732 K. Svanberg, M. Werme First and Second Order Sensitivities of Functions with Respect to Binary Variables and Their Application in Topology Optimization ................... 733
(ID-1867)
A. Vincenti, P. Vannucci Optimal Design of Smart Composite Laminates by the Polar Method and the Genetic Algorithm Bianca ......................................................... 734
(ID-2184)
C. Wang, B. Duan, F. Zheng, H. Cao On Optimization Platform for Coupled Structural-Electromagnetic Performances of Large Reflector Antennas......................................................... 735
(ID-1570)
H. Wang, J. Croll, N. Yamamoto, S. Yamada Optimising Buckling Capacities for Composite Shells ........................... 736
(ID-2511)
B. Wilczynski, Z. Mróz Multiaxial Plastic Hardening Models Used in Shape Optimization with Respect to Fatigue Life................................................................................ 737
(ID-2269)
A. Wit, A. Lipka, E. Ramm, F. Keulen Multi-Level Optimization of Material and Structural Layout ................. 738
(ID-2588)
MS.62 Structural Dynamics Organizers: Azevedo, J.
R. Almeida, J. Silva (ID-1727) A Stochastic Modelling of the Dynamical Response of Highway Bridge Decks Under Traffic Loads ..................................................................... 739 S. Amiri, M. Barghian, M. Fard, J. Safadoust Comparisation of Two Dimensional Nonlinear Analysis of Integral Abutment Bridge and Simply Supported Bridge ................................... 740
(ID-1095)
J. Chang, I. Huang, W. Hou, P. Chang Dynamic Stability Analysis of Truss Structures Under Nonconservative Constant and Pulsating Follower Forces ................................. 741
(ID-2597)
A. Davaran, M. Fard, S. Amiri, A. Kashefi Comparison of Concrete Tall Building Behavior Using an Intermittent Shear Walls Form in One Frame ..................................................... 742
(ID-1602)
S. François, G. Degrande An Iterative Coupled Boundary-Finite Element Method for the Dynamic Response of Structures......................................................................... 743
(ID-2666)
Table of Contents
lxv
S. Fransen, D. Rixen (ID-2090) Pendulum Mode Control in the Dynamic Analysis of Lift-Off of Launchers ............................................................................................................ 744 M. Gao, J. Pan, J. Xiong Dynamic Response of Long Span Cable-Stayed Bridge Subjected to Earthquake and Moving Train......................................................................... 745
(ID-2291)
M. Gutiérrez, H. Askes Parametrisation of the Newmark Time Integrator for Non-Linear Solid Dynamics ................................................................................................... 746
(ID-1201)
S. Krenk Global Formulation of Conservative Time Integration by the Increment of the Geometric Stiffness .................................................................. 747
(ID-2477)
D. Makovicka, D. Makovicka Response Analysis of Building Loaded by Groundborne Transient Vibration.............................................................................................................. 748
(ID-1220)
H. Marjamäki, J. Mäkinen Different Approaches in Modelling Boom Lifting Movement................ 749
(ID-1528)
B. Möller, W. Graf, A. Hoffmann, J. Sickert, F. Steinigen Textile Reinforced Concrete Structures Under Uncertain Dynamic Loading Processes ............................................................................................... 750
(ID-2232)
M. Ursu Shock Response Spectrum Analysis for Measured Earthquake Data ..................................................................................................................... 751
(ID-1973)
MS.64 System Identification and Finite Element Updating Organizers: Cunha, A.
A. Frigerio, E. Bom, G. Mazzà (ID-1444) Histride: an Integrated Software for Dynamic Structural Identification ....................................................................................................... 752 J. Lee, J. Kim, Y. Kim Damage Detection by the Topology Design Formulation Using Modal Parameters................................................................................................ 753
(ID-1739)
F. Magalhães, B. Costa, A. Cunha, E. Caetano Experimental Validation of the Finite Element Modelling of Pinhão Bridge ...................................................................................................... 754
(ID-2661)
S. Oliveira, P. Mendes Development of a Cabril Dam Finite Element Model for Dynamic Analysis Using Ambient Vibration Tests Results ............................................... 755
(ID-2077)
lxvi
Table of Contents
D. Rebolho, L. Souza, E. Belo, F. Marques (ID-2054) Application of Eera Method for Identification of Modal Parameters of a Simulated Aircraft ..................................................................... 756 E. Reynders, G. Roeck Reference-Based Combined Deterministic-Stochastic Subspace Identification for Experimental and Operational Model Analysis....................... 757
(ID-2508)
MS.65 Temperature and time dependent effects in steel and concrete structures Organizers: Silva, L. S., Júlio, E.
D. Costa, V. Silva, E. Júlio (ID-1253) Numerical Modelling of Time-Dependent Behaviour of High Strength Concrete Beams .................................................................................... 758 G. Ranzi, M. Bradford, P. Ansourian Behaviour of Composite Steel-Concrete Beams with Longitudinal and Transverse Partial Interaction in Fire............................................................ 759
(ID-1721)
G. Ranzi, P. Ansourian, L. Dezi, S. Zhang Partial Interaction Analysis of Multi-Layered Composite Beams Accounting for Time Effects ............................................................................... 760
(ID-1731)
A. Santiago, L. Silva, P. Real Numerical Behaviour of Steel Sub-Frame System in Fire ...................... 761
(ID-1814)
MS. 66 Vehicle Dynamics Organizers: Schiehlen, W.
J. Borges, M. Leal, R. Filho, J. Rezende (ID-2556) Structure Design and Dynamic Analysis of Vehicle Using Metamodeling and Optimization Techniques...................................................... 762 F. Braghin, E. Sabbioni, F. Cheli Race Driver Model: Identification of the Driver’s Inputs ....................... 763
(ID-1449)
F. Braghin, S. Melzi, F. Cheli Race Driver Model: Trajectory Planning ................................................ 764
(ID-1450)
F. Cheli, E. Giangiulio, E. Sabbioni, A. Concas A Simplified Abs Numerical Model for Actively Controlled Vehicle Dynamic Simulations: Validation with Experimental Data ................... 765
(ID-2096)
F. Cheli, G. Diana, F. Ripamonti, G. Tomasini, G. Zanetti Aerodynamic Sensitivity Analysis of the New Emuv250 Train to Cross Wind by Wind Tunnel Tests and CFD Analysis ....................................... 766
(ID-2391)
Table of Contents
lxvii
K. Dufva, K. Kerkkänen, L. Maqueda, A. Shabana (ID-1169) Three-Dimensional Large Deformation Finite Elment Analysis of Belt Drives........................................................................................................... 767 A. Freitas, R. Silva, J. Dias Multibody and Finite Element Models for the Design of Motorcyclist’s Roadside Protections ................................................................... 768
(ID-2397)
J. Landre, L. Saturnino, M. Becker, L. Patrício, C. Barcellos An Integrated Educational Tool for Vehicle Dynamical Response Studies ................................................................................................................. 769
(ID-1162)
J. Massat, A. Bobillot, J. Laine Robust Methods for Detecting Defects in Overhead Contact Line Based on Simulation Results ............................................................................... 770
(ID-1479)
B. Mavroudakis, P. Eberhard Mode Decoupling Vehicle Suspension System Applied to Race Car ....................................................................................................................... 771
(ID-1751)
J. Meijaard, A. Schwab Linearized Equations for an Extended Bicycle Model............................ 772
(ID-1715)
L. Patrício, M. Becker, J. Landre, C. Barcellos A New Vehicle 3D Model with 7 Degrees of Freedom for Vehicle Dynamical Response Studies .............................................................................. 773
(ID-1163)
J. Pombo, J. Ambrósio A Hertzian Contact Formulation for the Wheel-Rail Contact Problem in Railway Dynamics ............................................................................ 774
(ID-2639)
R. Portal, J. Dias Multibody Models for Vehicle Accident Reconstruction........................ 775
(ID-2396)
G. Rill (ID-2242)
First Order Tire Dynamics ...................................................................... 776
A. Schwab, J. Meijaard, J. Kooijman Experimental Validation of a Model of an Uncontrolled Bicycle ........... 777
(ID-1624)
G. Tomasini, A. Collina, E. Leo, F. Resta, F. Cheli Numerical-Experimental Methodology for Runnability Analysis and Wind-Bridge-Vehicle Interaction Study ....................................................... 778
(ID-2392)
P. Verissimo, J. Ambrósio Improved Bushing Models for Vehicle Dynamics .................................. 779
(ID-2362)
lxviii Table of Contents
MS.68 Behaviour of Structures Submitted to Extreme Event Organizers: Simões. L.C.
A. Dias Simulation of Large Deformations on Timber Joints Using 3D FEM Models........................................................................................................ 780
(ID-1967)
A. Freire, J. Negrão Nonlinear Dynamics of Flexible Partially Collapsed Structures............. 781
(ID-1787)
K. Jármai, J. Rodrigues Optimal Steel Frame Design for Fire Resistance .................................... 782
(ID-1116)
M. Larcher, L. Stempniewski Simulation of Shock Wave Loaded Concrete with Discrete Cracks ....... 783
(ID-1869)
A. Lopes, A. Cunha, L. Simões CFD Based Evaluation of the Lock-In Phenomenon of a Bridge Under Wind Load................................................................................................ 784
(ID-2443)
A. Lopes, D. Gomes, L. Simões CFD Based Aerodynamic Study to Discrete Optimization of Bridge Cross Sections.......................................................................................... 785
(ID-2444)
K. Menchel, P. Bouillard, T. Massart Progressive Collapse Simulation in RC Structures ................................. 786
(ID-1986)
V. Terzi, M. Alexoudi, K. Pitilakis, T. Hatzigogos Vulnerability Assessment for Pipelines Under Permanent Ground Deformatioon. Comparison Between Analytical and Empirical ......................... 787
(ID-1775)
R. Vicente, H. Rodrigues, H. Varum Seismic Performance and Strengthening of Traditional Masonry Buildings in the City Centre of Coimbra............................................................. 788
(ID-1359)
Preface This book contains the edited version of the Abstracts of Plenary and Keynote Lectures and Papers, and a companion CD-ROM with the full-length papers, presented at the III European Conference on Computational Mechanics: Solids, Structures and Coupled Problems in Engineering (ECCM-2006), held in the National Laboratory of Civil Engineering, Lisbon, Portugal 5th - 8th June 2006. The book reflects the state-of-art of Computation Mechanics in Solids, Structures and Coupled Problems in Engineering and it includes contributions by the world most active researchers in this field. ECCM-2006 is a continuation of the very successful Conferences held in Munich, Germany (1999) and Cracow, Poland (2001) and it is organized by the European Committee of Computational Solid and Structural Mechanics (ECCSM) of the European Community on Computational Methods in Applied Science (ECCOMAS) in collaboration with the Portuguese Association of Theoretical, Applied and Computational Mechanics (APMTAC), the Technical University of Lisbon and the National Laboratory of Civil Engineering. ECCM-2006 is attended by about 1000 participants from 70 countries. More than 1300 Abstracts were submitted to ECCM-2006. Altogether, 6 plenary lectures, 35 keynote lectures and 800 papers are presented in 58 organized symposia. A companion book, containing the edited version of the majority of Plenary and Keynote Lectures, entitled Computational Mechanics: Solids, Structures and Coupled Problems in Engineering is also published by Springer 2006. The Proceedings of the Conference could not be possible without the sponsorship and financial support of: European Community on Computational Methods in Applied Science (ECCOMAS); European Committee of Computational Solids and Structural Mechanics (ECCSM); International Association of Computational Mechanics (IACM); Portuguese Association of Theoretical, Applied and Computational Mechanics (APMTAC); Foundation of Science and Technology (Portugal); Calouste Gulbenkian Foundation (Portugal); Technical University of Lisbon (Portugal); National Laboratory of Civil Engineering (Portugal); Instituto Superior Técnico (Portugal). The Editors are grateful to all authors and to the reviewers that helped ensuring the scientific quality, allowing for this book to be published before ECCM2006. We acknowledge the support of Mr. Pedro Pinto of the Technical University of Lisbon, in the editing of the book. The Editors are also grateful to all Members of Executive, Organizing, Advisory and Scientific Committees and to the organizers of the Symposia, whose work made possible the success of ECCM-2006. We are grateful to Andrea Marques and Ana Catarina Amador for their effort and valuable assistance in the conference and preparation of this book. Technical University of Lisbon, Portugal, June 2006 Carlos A. Mota Soares, João A.C. Martins Helder C. Rodrigues, Jorge A.C. Ambrósio, Carlos A.B. Pina Cristóvão M. Mota Soares, Eduardo B.R. Pereira, João Folgado lxix
lxxi
Executive Committee E. Oñate (President of IACM), Polytechnic University of Catalunya, Spain A. Mang (President of ECCOMAS), Technical University of Vienna, Austria C. A. Mota Soares (Co-Chairperson), Technical University of Lisbon, Portugal M. Papadrakakis (Co-Chairperson), National Technical University of Athens, Greece B. Schrefler, University of Padua, Italy J. Teixeira de Freitas, Technical University of Lisbon, Portugal
Organizing Committee E. Arantes e Oliveira (Honorary Co-Chairperson), Technical Univ. of Lisbon, Portugal E. Stein (Honorary Co-Chairperson), University of Hannover, Germany J. Ambrósio, Technical University of Lisbon, Portugal M. Bernadou, University of Leonard de Vinci, France T. Burczynski, Silesian University of Technology, Poland P. Diez, Polytechnic University of Catalunya, Spain M. Kleiber, IPPT PAN, Poland O. Mahrenholz, Technische Universitat Hamburg, Germany J. Martins, Technical University of Lisbon, Portugal C.M. Mota Soares, Technical University of Lisbon, Portugal P. Neittaanmaki, University of Jyväskylä, Finland E. Pereira, Technical University of Lisbon, Portugal J. Periaux, Dassault Aviation, France C. Pina, National Laboratory of Civil Engineering, Portugal P.Steinmann, University of Kaiserslautern, Germany E. Ramm, University of Stuttgart, Germany H.C. Rodrigues, Technical University of Lisbon, Portugal N. E. Wiberg, Chalmers University of Techonology, Sweden O. C. Zienkiewicz, University of Wales, Swansea, United Kingdom
Management Committee Carlos Pina, National Laboratory of Civil Engineering, Portugal Helder Rodrigues, Technical University of Lisbon, Portugal João Martins, Technical University of Lisbon, Portugal
Organizing Institution Portuguese Association of Theoretical, Applied and Computational Mechanics LNEC, Av. do Brasil 101, 1700-066 Lisboa, Portugal
lxxii
Advisory Committee F. Auricchio, Associazione Italiana di Meccanica Teorica e Applicata, Italy N. Bicanic, Association for Computer Methods in Engineering (ACME), UK M.H. Boduroglu, Turkish Committee on Computational Mechanics, Turkey T. Burczynski, Polish Association for Computational Mechanics (PACM), Poland M. Casteleiro, Sociedad Española de Métodos Numéricos en Ingenieria (SEMNI), Spain M. Cerrolaza, Sociedad Venezolana de Métodos Numéricos en Ingenieria, Venezuela P. Chauchot, Computational Structural Mechanics Association (CSMA), France C. K. Choi, Korean Association on Computational Mechanics (KACM), Korea J. Crempien, Sociedade Chilena de Mecánica Computacional (SCMC), Chile R. Delgado, Portuguese Association of Theoretical, Applied and Computational Mechanics (APMTAC), Portugal A. Eriksson, The Nordic Association for Computational Mechanics (NOACM), Denmark, Estonia, Finland, Iceland, Latvia, Lithuania, Norway, Sweden J. Fish, U. S. Association for Computational Mechanics (USACM), USA I. Harari, The Israel Association of Computational Methods in Mechanics, Israel I. Herrera, Sociedad Mexicana de Métodos Numéricos en Ingenieria, México S.R. Idelsohn, Asociación Argentina de Mecánica Computational (AMCA), Argentina W. Kanok-Nukulchai, Thailand Society for Computational Mechanics (TSCM), Thailand T. Kant, India Association of Computation Mechanics, India M. Kleiber, The Central European Association for Computational Mechanics (CEACM), Austria, Croatia, Hungary, Poland, Slovenia, The Czech Republic V. Kompis, Slovakia Association for Computational Mechanics, Slovakia G. R. Liu, Singapore Association for Computational Mechanics (SACM), Singapore P.R. Lyra, Brazilian Association for Computational Mechanics (ABMEC), Brazil J. Miller, Irish Society for Scientifc and Engineering Computation (ISSEC), Ireland H. Ohtsubo, Japan Society of Computational Engineering Science (JSCES), Japan M. Papadrakakis, The Greek Association of Computational Mechanics (GRACM), Greece E. Ramm, German Association of Computational Mechanics (GACM), Germany B. D. Reddy, South Africa Association for Theorical and Applied Mechanics (SAAM), South Africa S. Valliapan, Australian Association of Computational Mechanics, Australia T. Yabe, Japan Association for Computational Mechanics (JACM), Japan M. W. Yuan, Chinese Association of Computational Mechanics, China
lxxiii
Scientific Committee S. Adali (South Africa) J. Alfaiate (Portugal) O. Allix (France) C. Alves (Portugal) C. António (Portugal) F. Amero (USA) J. Azevedo (Portugal) N. Banichuk (Russia) A.L. Baptista (Portugal) K.J. Bathe (USA) J. L. Batoz (France) P. Beckers (Belgium) T. Belytschko (USA) M. Bendsoe (Denmark) A. Benjeddou (France) P. Bergan (Norway) R. Borja (USA) R. de Borst (Netherland) F. Branco (Portugal) C.L. Bottasso (USA) E. Carrera (Italy) D. Camotim (Portugal) M. Casteleiro (Spain) J. Cesar Sá (Portugal) C. Chen (Taiwan) K.K. Choi, (USA) C. Cinquini (Italy) S. Cowin (USA) A. Cunha (Portugal) M. Doblaré (Spain) E.H .Dowel (USA) G. Dulikravich (USA) I. Doltsinis (Germany) R. Feijoo (Brazil) I. Figueiredo (Portugal) J. Fish (USA) L. Gaul (Germany) P.L. George (France) M. Geradin (Italy) E. Van der Giessen (Netherlands) M. Goicolea (Spain) C. Hellmich (Austria) J. Herskovits (Brazil) J. Holnicki-Szulc (Poland) G. Holzapfel (Austria) T.J.R. Hughes (USA) S. R. Idelsohn (Argentina)
R. Jorge (Portugal) J.J. Judice (Portugal) B. Karihaloo (UK) N. Kikuchi (USA) M. Kojic (USA) P. Ladevèze (France) V. Leitão (Portugal) T. Lekszycki (Poland) J. Vieira de Lemos (Portugal) A. Leung (China) W. K. Liu (USA) P. Lourenço (Portugal) B. Mace (UK) P. Martins (Portugal) R. Melchers (Australia) J. Moitinho de Almeida (Portugal) C. Navarro (Spain) P. Nikravesh (USA) J.T. Oden (USA) R. Ohayon (France) N. Olhoff (Denmark) X. Oliver (Spain) H. Orlande (Brasil) P. Pedersen (Denmark) H. Pina (Portugal) P. Prendergast (Ireland) A. Preumont (Belgium) J. N. Reddy (USA) P. Ribeiro (Portugal) R. Rolfes (Germany) W. Schiehlen (Germany) G.I. Schueller (Austria) O. Sigmund (Denmark) L. Simões (Portugal) J.C. Sousa (Portugal) R. Stenberg (Finland) A. Suleman (Portugal) A. Tadeu (Portugal) A. Torres Marques (Portgual) Z. Waszcyszyn (Poland) P. Wriggers (Germany) M. Zmindak (Slovak Republic) T.I. Zohdi (USA) Liu Gui-Rong (Singapore) M. Pietrzyk (Poland)
lxxiv
International Correspondents M. Bercovier, The Hebrew University, Jerusalem, Israel S. Botello, University of Guanajuato, Mexico M. Cerrolaza, Central University of Venezuela, Venezuela C. K. Choi, Korea Advanced Inst. of Sc. & Techn., Korea R. Correa, Universidad de Chile, Chile S. M. Desphande, Indian Inst. of Science, India P. R. B. Devloo, Universidade Estadual de Campinas, Brazil A. Gaona, Universidad Nat. de Asuncion, Paraguay I. Herrera, UNAM, Mexico J. Herskovits, Federal University of Rio de Janeiro, Brazil J. Hurtado, Universidad Manizales, Colombia W. Kanok-Nukulchai, Asian Institute of Technology, Thailand M. Kawahara, Chuo University, Japan T. Kawai, University of Science in Tokyo, Japan A. M. Kharitonov, Russian Academy of Sciences, Russia T. Kobayashi, Japan E. B. Las Casas, Brasilian Association for Comp. Mech., Brazil C. H. Lee, University of Aeronautics, China A. Leung, City University of Hong-Kong, China C. A. Lin, National Tsing Hua University, Taiwan L. Quiroz, Universidad de Concepcion, Chile C. V. Ramakrishnan, Indian Institute of Technology, India R. Sampaio, PUC Rio, Rio de Janeiro, Brazil L. Súarez, Universidad de Puerto Rico, Puerto Rico K.Y. Sze, The University of Hong Kong, China S. Valliappan, University of New South Wales, Australia K. William, University of Colorado USA J. Yagawa, University of Tokyo, Japan Y.B. Yang, National University of Taiwan, Taiwan M. Yuan, University of Beijing, China W.X. Zhong, Dalian University of Technology, China F. G. Zhuang, CNSA Chinese Aerodynamics, China M. Xiao, NUAA, China
Sponsors European Community on Computational Methods in Applied Science International Association of Computational Mechanics Portuguese Association of Theoretical, Applied and Computational Mechanics Foundation of Science and Technology (Portugal); Calouste Gulbenkian Foundation (Portugal); Technical University of Lisbon (Portugal); National Laboratory of Civil Engineering (Portugal); Instituto Superior Técnico (Portugal)
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
1
Computational Challenges for Multi-Physics Topology Optimization Martin P. Bendsøe Department of Mathematics, Technical University of Denmark Matematiktorvet B303, DK-2800 Kgs. Lyngby, Denmark
[email protected] ABSTRACT Topology design involves working with multiple fields. Of primary interest is the density distribution of material that makes a certain objective function minimal while other objectives are satisfied as constraints in a mathematical programming statement. The evaluation of the objective and constraint functions will involve state variables that are fields that relate the design variables to physical behavior. The state fields are scalar or vector fields and multiple fields representing various physical responses may be involved; these fields will typically be coupled in multi-physics applications. Computational procedures for topology design (and for design optimization as a whole) thus encompass discretization schemes for design and state fields together with algorithms for optimization and for analysis. The prevailing computational approach to structural design and topology design in particular is to view the optimization procedure as a problem in the design variables only. This means that analysis is treated as a function call that provides information on function values and derivatives as a function of design. In optimization terms this is a nested format. An alternative to the nested format is to treat design and state fields on equal terms and formulate one unified optimization problem that involves also state equations as constraints. This is the typical approach in the areas of Mathematical Programs with Equilibrium Constraints (MPECs) and PDE-constrained optimization. Finally, in some cases it turns out to be advantageous to treat the design variables as functions of the states, for example where an explicit calculation of the optimal design for a fixed state is possible. This then leads to a variational statement for the optimal state field in itself. Computational challenges are thus by the nature of the problem two-fold and successful implementations rely on both efficient analysis (and the associated sensitivity analysis) and on the efficiency of optimization algorithms. The discretization of the analysis and design fields play here a significant role for stability and for obtaining relevant results, and it is typical that the optimization will utilize a poor model to give results of little physical meaning. For the design field, the computational model will typically also include a relaxation of an integer valued field and suitable ways to handle this is a crucial issue especially when extending topology design from continuum structural applications to multi-physics settings. The different approaches and the associated computational issues involved in their resolution will be illustrated by considering some recent work on design of multi-physics devices and the design of articulated mechanisms.
References [1] M.P. Bendsøe & O. Sigmund, Topology Optimization - Theory, Methods, and Applications. Springer-Verlag, Berlin-Heidelberg, 2003 (revised printing, 2004). [2] K.K. Choi & N.-H. Kim, Structural Sensitivity Analysis and Optimization, Vol 1 & 2. SpringerVerlag, New York, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
2
Computational Geometry and the Analysis of Solids and Structures J.A. Cottrell , A. Reali†, Y. Bazilevs , T.J.R. Hughes Institute for Computational Engineering and Sciences The University of Texas at Austin 201 East 24th Street 1 University Station C0200 Austin, TX 78712, USA {jac3, bazily, hughes}@ices.utexas.edu †European
School for Advanced Studies in Reduction of Seismic Risk
[email protected]
ABSTRACT The concept of Isogeometric Analysis is described. Basis functions generated from NURBS (NonUniform Rational B-Splines) are employed to construct exact geometric models. For purposes of analysis, the basis is refined and/or its order elevated without changing the geometry or its parameterization. Analogues of finite-element, h-refinement and p- refinement schemes are presented, and a new, more efficient, higher-order concept, k-refinement, is introduced. Refinements are easily implemented and exact geometry is maintained at all levels without the necessity of subsequent communication with a CAD (Computer Aided Design) description. In the context of structural mechanics, it is established that the basis functions are complete with respect to affine transformations, meaning that all rigid body motions and constant strain states are exactly represented. Standard patch tests are likewise satisfied. Numerical examples exhibit optimal rates of convergence for linear elasticity problems and convergence to thin elastic shell solutions. The concept of k-refinement is explored and shown to produce more accurate and robust results than standard finite elements for problems of structural vibrations. Through the use of nonlinear parameterizations, optical branches of frequency spectra are eliminated for k-refined meshes. Optical branches have been identified as contributors to Gibbs phenomena in wave propagation problems and the cause of rapid degradation of higher modes in p-method finite elements. A geometrically exact model of the NASA Aluminum Testbed Cylinder is constructed and frequencies and mode shapes are computed and shown to compare favorably with experimental results. It is argued that Isogeometric Analysis is a powerful generalization of standard, polynomial-based, finite element analysis.
References [1] T.J.R. Hughes, J.A. Cottrell, Y. Bazilevs. Isogeometric Analysis: CAD, finite elements, NURBS, edxact geometry, and mesh refinement. Computer Methods in Applied Mechanics and Engineering, 194:4135–4195, 2005. [2] J.A. Cottrell, A. Reali, Y. Bazilevs, T.J.R. Hughes. Isogeometric Analysis of structural vibration. Computer Methods in Applied Mechanics and Engineering, in press, 2005. Also as an ICES report http://www.ices.utexas.edu.research/reports/2005/0527.pdf.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
3
Advances in the Particle Finite Element Method for Fluid-Structure Interaction Problems Eugenio Oñate, Sergio R. Idelsohn, Miguel A. Celigueta and Ricardo Rossi International Center for Numerical Methods in Engineering (CIMNE) Universidad Politécnica de Cataluña Campus Norte UPC, 08034 Barcelona, Spain
[email protected]
ABSTRACT There is an increasing interest in the development of robust and efficient numerical methods for analysis of engineering problems involving the interaction of fluids and structures accounting for large motions of the fluid free surface and the existence of fully or partially submerged bodies. Examples of this kind are common in ship hydrodynamics, off-shore structures, spillways in dams, free surface channel flows, liquid containers, stirring reactors, mould filling processes, etc. We present a general formulation for analysis of fluid-structure interaction problems using the particle finite element method (PFEM). The key feature of the PFEM is the use of a Lagrangian description to model the motion of nodes (particles) in both the fluid and the structure domains. Nodes are thus viewed as particles which can freely move and even separate from the main analysis domain representing, for instance, the effect of water drops. A mesh connects the nodes defining the discretized domain where the governing equations, expressed in an integral from, are solved as in the standard FEM. The necessary stabilization for dealing with the incompressibility condition in the fluid is introduced via the finite calculus (FIC) method. A fractional step scheme for the transient coupled fluid-structure solution is described. Examples of application of the PFEM method to solve a number of fluid-structure interaction problems involving large motions of the free surface and splashing of waves are presented.
References [1] E. Oñate, S.R. Idelsohn, F. Del Pin, R. Aubry, The particle finite element method. An overview, Int. J. Comput. Meth., Vol. 1 (2), 267-307, 2004. [2] S.R. Idelsohn, E. Oñate, F. Del Pin, The particle finite element method: a powerful tool to solve incompressible flows with free-surfaces and breaking waves, Int. J. for Num. Meth. in Engrg. Vol. 61, 964-989, 2004. [3] www.cimne.com/pfem
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
4
Elastic and Plastic Impacts in Multibody Dynamics Werner Schiehlen, Robert Seifried Institute of Engineering and Computational Mechanics Paffenwaldring 9, 70569 Stuttgart, Germany
[email protected] [email protected]
ABSTRACT Many mechanical systems are subject to impacts modeled as unilateral constraints using the multibody system approach and the coefficient of restitution found from measurements. A multi-scale method is presented for the computation of the coefficient of restitution considering elastic wave propagation and plastic deformation which may occur simultaneously. Different models are presented for the impact period: a continuum model and a modal model with elastostatic Hertzian contact resulting in a boundary approach, a linear modal model with precomputed and concurrently computed finite elements in the contact region, and a completely nonlinear finite element model. In engineering, impacts are usually emerging from repeated processes with repeated collisions occurring on a previously deformed contact area. Therefore, the efficient modal models are extended for the evaluation of repeated impacts. The influence of the initial velocity prior to the impact as well as the shape and the yield stress of the bodies involved are investigated. For the experiments a special test bench is designed using Laser-DopplerVibrometers for velocity and displacement measurements on a fast time scale.
References [1] C. Glocker, On frictionless impact models in rigid-body systems. Philosophical Transactions of the Royal Society of London, A359, 2385–2404, 2001. [2] W. Goldsmith, Impact: The Theory and Physical Behaviour of Colliding Solids, Edward Arnold Ltd, London, 1960. [3] B. Hu, W. Schiehlen, Multi-time scale simulation for impact systems: from wave propagation to rigid body motion. Archive of Applied Mechanics, 72, 885–897, 2003. [4] W. Schiehlen, R. Seifried, Three approaches for elastodynamic contact in multibody systems. Multibody System Dynamics, 12, 1–16, 2004. [5] W. Schiehlen, R, Seifried, P. Eberhard, Elastoplastic phenomena in multibody impact dynamics. Computer Methods in Applied Mechanics and Engineering, in press, [doi:10.1016/j.cma.2005.08.011]. [6] R. Seifried, W. Schiehlen, P. Eberhard, Numerical and experimental evaluation of the coefficient of restitution for repeated impacts. International Journal of Impact Engineering, 32, 508–524, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
5
Active Aeroelastic Aircraft Structures A. Suleman and P. A. Moniz Instituto de Engenharia Mecânica, Instituto Superior Técnico (IDMEC-IST), Lisbon, Portugal. Av. Rovisco Pais 1, 1049-001 Lisboa PORTUGAL
[email protected]
ABSTRACT Aeroelasticity results in problems such as structural divergence, aileron reversal, and flutter stability due to insufficient torsional stiffness of the wings and “aeroelastic weight penalty” became a widely used expression by engineers in aircraft design. Aeroelastic solutions generally involve increasing the structure stiffness or mass balance (passive solutions), which typically involve increase of weight and cost while decreasing performance. In the seventies, composite materials with highly anisotropic directional stiffness properties enabled the introduction of aeroelastic tailoring methods where the composition of thickness and orientation of the individual material layers could be tailored to minimize the added structural weight necessary to minimize the detrimental effects due to aeroelastic behavior. This technology paved the way for looking at aeroelasticity from a different perspective. The new paradigm consists of looking at the structural deformations, caused by aerodynamic forces, to be used intentionally and in a beneficial way in order to improve aerodynamic performance and help to create the required control forces. In the last two decades, a new actuation concept for structural control has emerged. This concept uses the multifunctional materials properties to control the structural stiffness and shape of composite materials. Several studies have been performed to demonstrate applications of adaptive structures in aircraft, helicopters and submarines. This paper presents the research and development of novel active aeroelastic control strategies, aimed at improved aircraft performance (structural weight, better control effectiveness) by controlling structural deformations to modulate the desired aerodynamic deformations. The proposed research was carried out in the framework of the European research project 3AS (Active Aeroelastic Aircraft Structures). To this end, the following research issues to enable active aeroelastic aircraft structures have been addressed: • Demonstrate the application of piezoelectric actuators and sensors to dynamic aeroelastic control of a structure and design an experimental and computational setup that allows the quantification of the performance in flutter suppression, buffeting vibration reduction, and attenuation of other external mechanical vibrations. • Develop an airborne flight test platform (RPV - Remotely Piloted Vehicle) to demonstrate the proposed concepts both in the wind tunnel and in actual flight conditions; • Develop a methodology to design and integrate the proposed adaptive structures technology in real aircraft while reducing the weight of a wing for a given flight envelope.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
6
Multiscale Strategy for Solving Industrial Problems O. Allix L.M.T., E.N.S. de Cachan/ C.N.R.S./Univ. P. et M. Curie 61, avenue du Président Wilson, 94235 Cachan, France
[email protected]
ABSTRACT Multi-scale strategies are now mature for most of linear spatial problem. They can also be applied as solver in the case of non-linear problem but it is our opinion that more robust and efficient methods can be designed in that case. Two examples will serve as illustration. The case of crack propagation [1] and the case of post-buckling analyses of aeronautical structures [2]. In [3] Ladevèze proposed a multi-scale strategy for solving non-linear problem. This method offers several possibilities to adapt it in order that the main difficulties of the problem are specifically treated. One of its appealing features is to split the macro part from the micro one at interface level only. This allow to work on the most adapted splitting of the interfacial quantities. The classical choice which allows to incorporate homogenization at the macro-level automatically is the one where the interfacial macro extractor is associated with the linear part. In the case of crack propagation it appears more adapted to introduce a discontinuous scheme at the macro level, the use of the PUM method [4] for crack allows improving the micro description of the solution. In the case of the post-buckling analysis of large aeronautical, the non-linear scheme used, allows to iterate where it is needed only, that is in the sub-structures prone to the highest degree of nonlinearity. As non-linearities are often localized (i. e; corresponds to a local buckling giving rise to large displacement of the whole structure) the computational effort can be reduced drastically in comparison with a classical [2].
References [1] P.-A. Guidault, O. Allix, L. Champaney , J.-P. Navarro “A micro-macro approach for crack propagation with local enrichment”, to appear in CST [2] Ph. Cresta, O. Allix, C Rey, S Guinard "Nonlinear localization strategies for domain decomposition methods: application to post-buckling analyses" to apppear in CMAME [3] P. Ladevèze, O. Loiseau, D. Dureisseix, “A micro-macro and parallel computational strategy for highly heterogeneous structures”, IJNME, 52 (1–2) 121–138,2001. [4] J. Melenk, I. Babuska, “The partition of unity finite element method: Basic theory and applications”, Computer Methods in Applied Mechanics and Engineering 139, 289–314, 1996.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
7
Numerical Integration of the Nonlinear Dynamics of Elastoplastic Solids Francisco Armero & Christian Zambrana Structural Engineering, Mechanics and Materials University of California at Berkeley Berkeley, CA 94720
[email protected]
ABSTRACT Classical numerical schemes for the numerical integration of the equations of solid and structural dynamics in time show serious limitations when applied to the finite deformation range. These includes the classical Newmark and HHT type schemes. The unconditional stability property of some of these schemes is lost in the nonlinear range, with the simulations showing an unbounded growth of energy. Furthermore, the law of conservation of angular momentum is, in general, not inherited by the schemes in this nonlinear range either. To handle these difficulties, the formulation of the so-called energymomentum schemes has received a great deal of attention lately. As illustrated in [1], these difficulties are also present in the physically dissipative problem of finite strain plasticity. The schemes do not lead to dissipative discrete dynamical systems. We present in this contribution a new class of integration schemes for multiplicative finite strain plasticity that exhibit the non-negative energy dissipation characteristic of these physical systems and that preserve the conservation laws of linear and angular momenta in time. The exact physical dissipation is obtained, hence recovering previously developed energy-momentum schemes with the exact energy conservation for elastic problems in elastic steps of the elastoplastic simulations. Furthermore, the schemes allow the consideration of extensions showing a controllable high-frequency (numerical) energy dissipation to handle the numerical schemes of typical problems of interest. The new schemes rely on an alternative integration of the plastic evolution equations, or return mapping algorithm, that define the discrete in time evolution of the plastic internal variables and the exact enforcement of the yield constraint on the stresses driving the motion. We built on the developments presented in [1] and incorporate an additional set of new considerations for the volumetric contributions, thus arriving to algorithms that also preserve exactly the isochoric character of the plastic flow in some common models of finite strain plasticity (e.g. J2 -flow theory based on von Mises yield criteria). Moreover, we discuss the implementation of the new time-stepping schemes in the context of new formulations of assumed strain and mixed finite elements for the handling of the well-known volumetric locking in these cases, while obtaining the aforementioned conservation and dissipation properties in time. Several numerical simulations are presented illustrating the performance of the new schemes.
References [1] F. Armero, Energy-Dissipative Momentum-Conserving Time-Stepping Algorithms for Finite Strain Multiplicative Plasticity, Computer Methods in Applied Mechanics and Engineering, in press.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
8
Computational Methods for Dynamic Crack Propagation Ted Belytschko, Song, Wang Northwestern University, Department of Mechanical Engineering 2145 North Sheridan Road, Evanston, IL 60208-3111
[email protected]
ABSTRACT Several methods for dynamic computational fracture mechanics are reviewed, and their performance in some benchmark problems is reviewed. The methods considered include element deletion, interelement unzipping models and the extended finite element method. Element deletion consists of simply deleting the element when a material criterion is met. The inter-element crack models are of the type proposed by Xu and Needleman, and by Ortiz and Pandolfi. The extended finite element method permits arbitrary crack propagation within the mesh. Advancement of the crack by several criteria is studied. Among the results that are compared are the crack paths, the speed of the crack and the energy dissipated by the fracture process.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
9
Analysis and Design of Sandwich Structures Made of Steel and Lightweight Concrete Pål G. Bergan*, Kåre Bakken*, Karl-Christian Thienel† *
Det Norske Veritas Research NO-1322 Høvik Norway
[email protected] [email protected]
†
Universität der Bundeswehr DE-85577 Neubiberg Germany
[email protected]
ABSTRACT Reinforced concrete has been used in ship building for more than 150 years; particularly during war periods with shortage of steel. Unfortunately, this inexpensive material has proven not to be commercially viable, primarily because of added weight. A new concept for design of ships and marine structures has been developed using sandwich plates composed of steel skins with lightweight concrete as core material. New types of light-weight concretes have been developed and tested for this purpose. Very large structures can be built without increasing the core thickness considerably; scalability is achieved by way of a cellular structural concept. A Panmax type bulk carrier ship has been designed and analyzed by way of linear finite elements. The study shows great promise for this new sandwich concept in that it appears that it saves 30 to 40 percent of the steel and comes out with about the same weight compared with a standard steel ship design. It also seems clear that the sandwich concept may offer important advantages when it comes to safety, design life, and operational performance. The current type of concretes is very light with wet, demoulding density of less than 1000 kg/m3. Its use in sandwich panels has been extensively tested in the laboratory. Some testing has focused on strength of the light-weight concrete in compression and shear, whereas other tests have dealt with bond and pull-out strength in the steel-concrete interaction. The laboratory program has included static and fatigue testing of series of sandwich beams; it has to a large extent focused on interaction effects and the failure of the core material, particularly in shear failure. The testing shows how cracks initiate and develop. The cracks in the test specimen have a highly jagged appearance, indicating extensive capability of shear force transfer across cracks (shear locking). The tests also show that delamination primarily occurs as a secondary phenomenon, normally a short distance away from the contact plane between steel and concrete. The most remarkable finding is that the beams exhibit extensive ductility and ability to absorb energy far beyond initial cracking. A key to this behaviour is that the surface skins are locked by end plates at the end of the beams. The study reveals that there is a need for developing good mathematical models for this unconventional concrete. There is also a need for further developing nonlinear finite elements models that can simulate the complex behaviour and interaction effects of steel-concrete sandwich plates during all stages of damage development. The practical potential of this technology is very extensive.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
10
Multiscale Modeling of Pore Collapse Instability in High-Porosity Solids Ronaldo I. Borja* *
Department of Civil and Environmental Engineering Stanford University, Stanford, CA 94305-4020, USA
[email protected]
ABSTRACT High-porosity solids include elastomeric foams and other cellular materials, Aeolian sands, poorly cemented coquina, diatomite, and chalk. A majority of these materials are known to exhibit several regions of behavior in simple uniaxial or conventional triaxial compression: a nearly linearly elastic behavior at small strain, plastic behavior at larger strain, a plateau region in which strain increases at nearly constant stress, and, finally, a densification region characterized by pore collapse. In this paper we address the problem of pore collapse instability as a local bifurcation from a homogeneous solution driven by a singular constitutive tangent operator. We identify different eigenmodes (emodes) of bifurcation and propose an approach for constitutive branching useful for multiscale modeling of the pore collapse/densification process.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
11
Instabilities and Discontinuities in Two-Phase Media René de Borst 1, 2, Marie-Angèle Abellan 3, Julien Réthoré 1 1
2
Faculty of Aerospace Engineering, Delft University of Technology P.O. Box 5058, 2600 GB Delft, The Netherlands
[email protected]
LaMCoS – UMR CNRS 5514, INSA de Lyon, 69621 Villeurbanne, France 3
LTDS-ENISE – UMR CNRS 5513, Saint-Etienne, France
ABSTRACT Within the framework of the generalised theory of heterogeneous media, the complete set of equations is derived for a three-dimensional fluid-saturated porous medium. Subsequently, dispersion analyses are carried out for an infinite one-dimensional continuum, that has been deforming homogeneously prior to the application of the perturbation. A dispersive wave is obtained, but the internal length scale associated with it vanishes in the short wave--length limit, at least for the assumptions made regarding the constitutive behaviour of the solid and of the fluid. This result leads to the conclusion that, upon the introduction of softening, localisation in a zero width will occur and no regularisation will be present. This conclusion is corroborated by the results of numerical analyses of wave propagation in a finite one-dimensional bar [1]. The result has severe implications for finite element analyses of damaging multiphase media, since they will be mesh-dependent. To avoid mesh dependence, either the constitutive model for the solid must be equipped with a nonvanishing internal length scale, or any damage that occurs must be modelled in a strictly discrete manner. The second part of the contribution therefore focuses on the proper modelling of discontinuities in fluid-saturated porous media. A two-field finite element formulation has been set up with the displacements and the fluid pressure as the fundamental unknowns [2]. At discontinuities in the body, e.g. cracks, the displacement and the fluid pressure fields are allowed to be discontinuous. Numerically, the discontinuities in the displacements and the fluid pressure are incorporated using the partition-of-unity property of finite element shape functions. The tractions at the interface are related to the displacement jumps using a cohesive zone model, where the behaviour in the direction normal to the interface can be different from that in the tangential direction. Regarding the pore fluid flow, it has been assumed that the normal flux to the interface is proportional to the jump in pore pressures at both sides of the discontinuity, which can be conceived as the discrete analogon of Darcy’s relation for fluid flow in porous media. The paper concludes with some examples of finite element analyses of fluid-saturated porous media with discontinuities.
References [1] M.-A. Abellan, R, de Borst, Wave propagation and localisation in a softening two-phase medium. Computer Methods in Applied Mechanics and Engineering, doi: 10.1016/j.cma.2005.05.056. [2] R. de Borst, J.J.C. Remmers, A. Needleman, M.-A. Abellan, Discrete vs smeared crack models for concrete fracture: Bridging the gap. International Journal for Numerical and Analytical Methods in Geomechanics, 28, 583-607, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
12
Towards Maneuvering Aeroelasticity — Progress in the Simulation of Large Fluid-Structure Interaction Problems Carlo L. Bottasso Politecnico di Milano Via La Masa 34, 20156 Milano, Italy
[email protected]
ABSTRACT Advanced multidisciplinary software tools enable the development of sophisticated models of fixed and rotary wing vehicles. Such comprehensive vehicle models account for the interactions between the structural and aerodynamic fields, often coupled with hydraulic and electromechanical subsystem models and with control laws (aero-servo-elasticity). With these models it is now possible to predict with a growing level of confidence a variety of phenomena that are of crucial importance in the design phase, including loads, performance, stability, vibratory response, handling qualities and flight mechanics characteristics of the vehicle. The quick pace of the evolution of comprehensive vehicle models must be accompanied by a similar growth in the range of problems that can be addressed by simulation. In particular, it is clear that quite often the limiting factors that constrain the design are found in the maneuvering regime at the boundaries of the flight envelope. For example, a design engineer might be interested in flying a minimum time turn with a virtual model of a helicopter while not exceeding a maximum allowable load factor, in order to assess the vibratory characteristics of the machine in this extreme turn. Current aeroelastic simulation tools are not directly equipped to solve this class of problems, since in fact they all compute the dynamic response of the model under the action of assigned control inputs. Unfortunately, control inputs that will fly a given maneuver are in general not available, and must be computed. In this paper we describe a methodology for maneuvering aeroelasticity that is applicable to arbitrarily complex vehicle models. The approach is based on model-based virtual pilots that, on the basis of a formal maneuver description, first plan the path of the vehicle throughout the maneuver and then track it by driving the vehicle model along it, as proposed in Reference [1]. Both planning and tracking pilots are based on adaptive reduced models of the system and have the ability to learn, and hence improve their driving performance, as they steer the vehicle. We illustrate the use of this emerging technology with the help of relevant examples in the area of rotorcraft technology.
References [1] C.L. Bottasso, C.-S. Chang, A. Croce, D. Leonello, L. Riviello, Adaptive planning and tracking of trajectories for the simulation of maneuvers with multibody models. Computer Methods in Applied Mechanics and Engineering, in press, available online 10 October 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
13
A Design Optimization Formulation for Problems with Random and Fuzzy Input Variables Using Performance Measure Approach K.K. Choi and Liu Du Department of Mechanical and Industrial Engineering The University of Iowa, Iowa City, IA 52242, U.S.A.
[email protected] [email protected]
ABSTRACT To obtain reliable designs, aleatory and epistemic uncertainties are considered recently in the structural analysis and design optimization. The reliability based de-sign optimization (RBDO) method [1] is used when the amount of input data is sufficient enough to create accurate statistical distribution. On the other hand, when the sufficient input data are not available due to limitations in time, human, and facility resources, the optimum design may not be reliable if RBDO method is used. To deal with the situation that input uncertainties have insufficient information, a possibility (or fuzzy set) method can be used for structural analysis and possibility based design optimization (PBDO) [2]. However, in many industry design problems, we may have to deal with design problems that involve with the mixed input statistical random and fuzzy variables simultaneously. For these problems, RBDO may yield unreliable optimum designs because of insufficient data. On the other hand, treating the random variables as fuzzy variables and invoking PBDO to solve the mixed design variable problem may yield too conservative designs with higher optimum costs. This paper proposes a new mixed variable design optimization (MVDO) problem based on the performance measure approach (PMA) [1]. To evaluate the possibilistic constraint in MVDO, a sub-optimization problem for inverse analysis is carried out using a hyper-cylinder domain. To solve this sub-problem efficiently and effectively, a new numerical algorithm, maximum failure search (MFS) method, is proposed in this paper by combining the enhanced hybrid mean value (HMV+) method [3] for the inverse reliability analysis in RBDO and the maximal possibility search (MPS) method [2] for the inverse possibility analysis in PBDO. Some mathematical examples are used to demonstrate the efficiency and effectiveness of the proposed numerical MFS method. Some physical design examples are used to compare the proposed MVDO results with RBDO and PBDO results.
References [1] Youn BD, Choi KK, Park YH (2003) Hybrid analysis method for reliability-based de-sign optimization. Journal of Mechanical Design, ASME 125(2): 221-232 [2] Du L, Choi, KK, Youn BD. An Inverse Possibility Analysis Method For Possibility-Based Design Optimization. AIAA Journal, to be appear. [3] Youn BD, Choi KK, Du L (2005) Enriched Performance Measure Approach for Reliability-Based Design Optimization. AIAA Journal 43(4): 874-884
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
14
Strength of Porous Ceramics – Mechanical Testing and Numerical Modelling Ioannis Doltsinis Faculty of Aerospace Engineering and Geodesy, University of Stuttgart Pfaffenwaldring 27, D-70569 Stuttgart
[email protected]
ABSTRACT The lecture addresses modelling of the damage of porous ceramics on the microstructural level, and the failure of structural components. The research has been occasioned by the industrial interest in the strength of ceramic filter supports used in nanofiltration, where internal pressure is of importance. Porous ceramics subjected to fluid pressure in the pores are prone to brittle microfracturing which may progress to brittle or quasi-brittle rupture of the component. Apart from physical and numerical modelling on the microscale, subtle laboratory testing of components has been of paramount importance; brittleness suggests statistical evaluation. The study focuses on mechanical issues, but conceptual thoughts on stress-enhanced corrosion are included [4]. The phenomenon is significant to aging which determines the life-time of parts exposed to chemically aggressive media. A brief discussion on the formalism for the fracturing continuum [1] is followed by the modelling of cracking by separation of grain boundaries. The associated algorithm simulates progressive damage on artificial microstructures generated in the computer for given material characteristics [2], and determines rupture statistics in dependence of various parameters. Laboratory measurements on the structural parts of interest (circular cylinders with longitudinal channels) refer to the diametral compression (Brazilian) test which adequately replaces the condition of channel pressure [3], as justified by finite element stress analysis. The impact of the two loading cases on Weibull statistics is formally explained, effects of basic material and doping on component rupture are investigated, the damage tolerance confirmed, corrosion discussed. Synthesis incorporates material strength statistics in the finite element model and estimates critical locations in the structural part under internal pressure. There is quantitative agreement with pressure levels actually registered at rupture. The account refers to cooperative research performed at the Universities of Stuttgart and Caen [4].
References [1] I. Doltsinis, Issues in modelling distributed fracturing in brittle solids with microstructure, in: S.R. Idelsohn et al. (Eds.), Computational Mechanics - New Trends and Applications. (CDROM) CIMNE, Barcelona, 1998. [2] I. Doltsinis and R. Dattke, Modelling the damage of ceramics under pore pressure, Comput. Meths. Appl. Mech. Engng., 191, 29-46, 2001. [3] F. Osterstock, I. Doltsinis, O. Vansse O, The Brazilian reliability test and micromechanical modelling for channelled cylinders of multiphase porous ceramics, in: High-Performance Ceramics II, Trans. Tech. Publications, 2004. [4] I. Doltsinis and F. Osterstock, Modelling and experimentation on the strength of porous ceramics, Arch. Comput. Meth. Engng., 12, 303-336, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
15
Reduced Order Models in Unsteady Aerodynamic Models, Aeroelasticity and Molecular Dynamics Earl H. Dowell*, Kenneth C. Hall*, Jeffrey P. Thomas*, Robert E. Kielb*, Meredith A. Spiker*, Charles M. Denegri, Jr. † *
†
Duke University, Durham, North Carolina, United States
[email protected]
U.S. Air Force SEEK EAGLE Office, Eglin Air Force Base, Florida, United States
ABSTRACT The state of reduced order modeling of unsteady aerodynamic flows for the efficient calculation of fluid-structure interaction (aeroelasticity) is discussed. Reduced order modeling is a set of conceptually novel and computationally efficient techniques for computing unsteady flow about airfoils, wings, and turbomachinery cascades. Starting with either a time domain or frequency domain computational fluid dynamics (CFD) analysis of unsteady aerodynamic flows, a large, sparse eigenvalue problem is solved. Then, using just a few of the resulting aerodynamic eigenmodes, a Reduced Order Model (ROM) of the unsteady flow is constructed. The aerodynamic ROM can then be combined with a similar ROM for the structure to provide a Reduced Order Aeroelastic Model that reduces computational model sized and cost by several orders of magnitude. Moreover, the aerodynamic and aeroelastic eigenvalue and eigenmode information provides important insights into the physics of unsteady flows and fluidstructure interaction. The method is particularly well suited for use in the active control of aeroelastic (fluid-structural) and unsteady aerodynamic phenomena as well as in standard aeroelastic analysis. As an alternative to the use of aerodynamic eigenmodes, Proper Orthogonal Decomposition (POD) has also been explored. POD is an attractive alternative because of the greater simplicity of calculating POD modes rather than fluid eigenmodes per se. Moreover once the POD modes have been used to construct a Reduced Order Model, this ROM may be used to find a good approximation to the dominant aerodynamic eigenmodes. After the Hopf Bifurcation (flutter) condition is determined for the fluid-structural system, a novel High Dimensional Harmonic Balance (HDHB) solution method for the fluid (and structural) model(s) proves to be a very efficient technique for determining limit cycle oscillations in fluid-structural systems. In this approach one exploits the knowledge of the aeroelastic eigenmode determined from the aeroelastic ROM. Several examples will be discussed including the limit cycle oscillations (LCO) of the F-16 aircraft and the limit cycle oscillations (LCO) of the Von Karman vortex street behind a cylinder in a cross-flow. The latter is a prototypical example of self-excited fluid oscillations that occur for bluff bodies including wings at high angles of attack. Correlation of theoretical calculations with experiment will also be shown.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
16
Inverse Engineering George S. Dulikravich1, Helcio R. B. Orlande2 and Brian H. Dennis3 1
2
3
Florida International University, Department of Mechanical & Materials Eng. 10555 West Flagler Street, Room EC 3474, Miami, Florida 33174, U.S.A.
[email protected]
Federal University of Rio de Janeiro, Department of Mechanical Eng., COPPE, Cid. Universitaria, Cx. Postal 68503, Rio de Janeiro, RJ, 21941-972, Brazil
[email protected]
Department of Mechanical and Aerospace Eng., University of Texas at Arlington, Arlington, Texas 78712, U.S.A.
[email protected]
ABSTRACT Inverse problems are rapidly becoming a multi-disciplinary field with many practical engineering applications. The objective of this lecture is to present several such multi-disciplinary concepts and applications. In some examples, sophisticated regularization formulations were used. In other examples, different optimization algorithms were used as tools to solve de facto inverse problems. Due to the mathematical complexity of these multi-disciplinary and often multi-scale inverse problems, the most widely acceptable formulations eventually result in a need for minimization of a certain norm or a simultaneous extremization of several such norms. These single-objective and multiobjective minimization problems are then solved using appropriate robust evolutionary optimization algorithms. Specifically, we focus here on inverse problems of determining spatial distribution of a heat source for specified thermal boundary conditions, finding simultaneously thermal and stress/deformation boundary conditions on inaccessible boundaries, and determining chemical compositions of steel alloys for specified multiple properties.
References [1] M.N. Özisik, HRB Orlande, Inverse Heat Transfer: Fundamentals and Applications, Taylor & Francis, New York, NY, USA, 2000. [2] P.M.P. Silva, H.R.B. Orlande, M.J. Colaco, P.S. Shiakolas, G.S. Dulikravich, Estimation of Spatially and Time Dependent Source Term in a Two-Region Problem. In Proceedings of the 5th International Conference on Inverse Problems in Engineering: Theory and Practic (Lesnic, D. ed.) July 11-15, 2005, Cambridge, United Kingdom [3] B.H. Dennis, G.S. Dulikravich, Z.-X. Han, Determination of Temperatures and Heat Fluxes on Surfaces and Interfaces of Multi-domain Three-Dimensional Electronic Components. ASME Journal of Electronic Packaging, Vol. 126, No. 4, December 2004, pp. 457-464. [4] B.H. Dennis, G.S. Dulikravich, S. Yoshimura, A Finite Element Formulation for the Determination of Unknown Boundary Conditions for Three-Dimensional Steady Thermoelastic Problems. ASME J. of Heat Transfer, Vol. 126, February 2004, pp. 110-118. [5] I.N. Egorov-Yegorov, G.S. Dulikravich, Inverse Design of Alloys for Specified Stress, Temperature and Time-to-Rupture by Using Stochastic Optimization. International Symposium on Inverse Problems, Design and Optimization – IPDO (Eds: Colaco, M., Orlande, H., Dulikravich, G.), Rio de Janeiro, Brazil, March 17-19, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
17
Multiscale Approaches for Bridging Discrete and Continuum Scales Jacob Fish and Wen Chen Rensselaer Polytechnic Institute
[email protected],
[email protected]
ABSTRACT In this talk, I will present information-passing and concurrent discrete-to-continuum scale bridging approaches. In the concurrent approach both, the discrete and continuum scales are simultaneously resolved, whereas in the information-passing schemes, the discrete scale is modeled and its gross response is infused into the continuum scale. For the information-passing multiscale methods to be valid both the temporal and spatial scales should be separable. Among the information-passing bridging techniques, I will present the Generalized Mathematical Homogenization (GMH) theory [1,2] and the Multiscale Enrichment based on the Partition of Unity (MEPU) method [3]. The GMH constructs an equivalent continuum description directly from molecular dynamics (MD) equations. The MEPU approach gives rise to the enriched quasicontinuum formulation, capable of dealing with heterogeneous inter-atomic potentials, nonperiodic fields and high velocity impact applications. The second part of the talk will focus on multiscale systems, whose response depend inherently on physics at multiple scales, such as turbulence, crack propagation, friction, and problems involving nano-like devices. For these types of problems, multiple scales have to be simultaneously resolved in different portions of the problem domain. Among the concurrent bridging techniques, attention will be restricted to multilevel-like methods [4,5]. A space-time multilevel method for bridging discrete scales with either coarse grained discrete or continuum scales will be presented. The method consists of the wave-form relaxation scheme aimed at capturing the high frequency response of the atomistic vibrations and the coarse scale solution (explicit or implicit) intended to resolve the coarse scale features (in both space and time domains) of the discrete medium
References [1] J. Fish and C. Schwob, “Towards Constitutive Model Based on Atomistics,” International Journal of Multiscale Computational Engineering, Vol. 1 pp. 43-56, (2003). [2] W. Chen and J. Fish, “A Generalized Space-Time Mathematical Homogenization Theory for Bridging Atomistic and Continuum Scales,” to appear in Int. J. Num. Meth. Eng., (2005). [3] J. Fish and Z. Yuan, “Multiscale Enrichment based on Partition of Unity,” International Journal for Numerical Methods in Engineering, (2004), in print. [4] J. Fish and W. Chen, “Discrete-to-Continuum Bridging Based on Multigrid Principles,” Comp. Meth. Appl. Mech. Engng., Vol. 193, pp. 1693-1711, (2004). [5] H. Waisman and J. Fish, “Space-Time multigrid method for bridging discrete scales,” submitted to International Journal for Numerical Methods in Engineering (2005)
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
18
Adaptive Mesh Generation in 3 Dimensions by Means of a Delaunay Based Method. Applications to Mechanical Problems. Paul Louis George ∗ INRIA,
Domaine de Voluceau, F 78153 Le Chesnay Cedex
[email protected]
ABSTRACT Mesh adaptation is recognized as a powerful tool to compute accurate solution while minimizing the required resources (CPU time and memory space), therefore avoiding using parallel computing. It is also a way to accurately capture the physical behavior of the PDE problem in hand and, in some cases, this is the only way to access to a reasonable solution. Mesh adaptation in two dimensions can be considered as mature and is used in various problems. Right now, in three dimensions, the question is much more tedious and only a limited number of works can be reported. Mesh adaptation can be considered in two different ways. The first makes use of local modification of the current mesh so as to adapt it. Modification tools include well known operators such as point relocation, collapse (mesh coarsening), edge flips, point addition (mesh enrichment). Relatively easy to implement, such methods proved to give nice results in a number of cases but are not so flexible in specific when anisotropic features are desired. The second is based on the full generation of a new (adapted) mesh based on the current one and metric data provided at the nodes of this mesh. The generation method is then a variant (widely different in various aspects) of the well know mesh generation method. The aim being not only to mesh at the best a given domain but to match the given metric, which is much more demanding. We are concerned with this second approach and we propose a Delaunay based mesh generation method capable to complete adapted meshes. The mesh generation aspect is driven by metric data (element size and directional specification) which are defined by means of error estimates. Isotropic and anisotropic meshes can be produced. Concrete application examples will demonstrate the flexibility of the proposed method, show the low cost of the approach which compares well with the first approach.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
19
Computational Micromechanics of Biological Materials: Bone and Wood Christian Hellmich∗ , Karin Hofstetter∗ , Cornelia Kober† ∗ Vienna
†
University of Technology (TU Wien), Institute for Mechanics of Materials and Structures Karlsplatz 13/202, A-1040 Wien (Vienna), Austria
[email protected],
[email protected]
Osnabr¨uck University of Applied Science, Faculty of Engineering and Computer Science Albrechtsstraße 30, D-49009 Osnabr¨uck, Germany
[email protected] ABSTRACT
Despite complex hierarchical organization of bone and wood, it was recently possible to identify a few elementary components at the micro and nanolevel of these material classes for the explanation of the diversity of macroscopic (poro-)elastic properties of different bones and woods [2, 3]. The mechanical properties (i.e. elasticity) of these elementary components are (up to experimental scattering) the same across a variety of different bones and woods, respectively; they are ’universal’, i.e., independent of tissue-type, species, and anatomical location. The mechanical interaction between these elementary components (mechanical morphology) and the dosages of these components in different tissues determine the macroscopic material properties. Having in mind that, as regards bone, these dosages are dependent on complex biochemical control cycles (defining the metabolism of the organism), the purely mechanical theory can be linked to biology, biochemistry, and, on the applied side, to clinical practice. Drug-driven or genetically driven changes in metabolisms lead to changes in the dosages of elementary components. The effects of these metabolic changes on the mechanical behavior of skeletal (sub)systems under well-defined loading conditions (e.g., downfall of elderly persons with osteoporosis) can then be studied by feeding structural models (e.g., Finite Element models [4]) of whole bones with the aforementioned macroscopic material properties - the output of the micromechanical models. This is probably highly relevant for patient-specific non-invasive bone disease diagnosis and therapy. As regards wood, our nano-to-macro approach is expected to support optimization of technological processes, such as drying.
References [1] L. Dormieux and F.-J. Ulm, editors. CISM Vol.480 – Applied Micromechanics of Porous Media. Springer, Wien - New York, 2005. [2] Ch. Hellmich. Microelasticity of bone, pages 289 – 331. In Dormieux and Ulm [1], 2005. [3] K. Hofstetter, C. Hellmich, and J. Eberhardsteiner. Development and experimental validation of a continuum micromechanics model for the elasticity of wood. European Journal of Mechanics A Solids, 24:1030 – 1053, 2005. [4] C. Kober, B. Erdmann, Ch. Hellmich, R. Sader, and H.-F. Zeilhofer. Validation of interdependency between inner structure visualization and structural mechanics simulation. International Congress Series, 1281:1373, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
20
Mechanobiology: Computation and Clinical Application Gerhard A. Holzapfel∗† , Christian T. Gasser∗ , Dimitris Kiousis∗ ∗ Royal
Institute of Technology (KTH), School of Engineering Sciences Osquars backe 1, 100 44 Stockholm, Sweden {gh,tg,dk}@hallf.kth.se
† Graz
University of Technology, Computational Biomechanics Schiesstattgasse 14-B, 8010 Graz, Austria
[email protected] ABSTRACT
Some reasons for the present worldwide procession of biomechanics are the exciting new developments in biology and the rapidly expanding field of mechanobiology, which aims to understand how cells respond to changes in their mechanical environment. Mechanobiology also studies the mechanical factors that may be important in, e.g., triggering the onset of atherosclerosis or aneurysms. Because of the inherent geometric, structural and material complexities of biological tissues [1], and the spatially non-uniform and time-varying boundary conditions, these type of problems demand computational methods [2], sufficient computational resources and graphics capability to display three-dimensional results. Computational models offer the potential to simulate multifield coupled processes encountered in the micro-heterogeneous biological tissues, and to realistically predict physiological functional interactions. Computational mechanobiology of biological tissue is increasing our ability to address multidisciplinary problems of academic, industrial and clinical importance. This presentation deals with the 3D modeling of balloon angioplasty, in particular of the interaction of balloon, stent and an atherosclerotic carotid artery. The artery is modeled as a heterogenous structure composed of three layers and a plaque. Distinctive attention is paid to the 3D contact of the artery with a stent and a balloon catheter, inflated with the goal to enlarge the area of the vessel. We use a smooth contact representation which is shown to be superior with respect to facet elements discretizing the interacting bodies. In addition, the dissection of the plaque, typically occurring during balloon inflation, is modeled by means of strong discontinuities and the application of the theory of cohesive zones using the partition of unity finite element method [3]. Contact pressure between the balloon-stent structure and the arterial wall leads to non-physiological stress concentration that can trigger adverse biological responses of the cells culminating in in-stent restenosis. Indeed, it has been shown that the design of a stent is a major risk factor for restenosis. A strategy of designing novel stents is shown with the goal to minimize vascular injury and to optimize long-term success [1]. Acknowledgement. Financial support for this research was partly provided by the Austrian Science Foundation under START-Award Y74-TEC, and KTH.
References [1] G. A. Holzapfel and R. W. Ogden, editors. Mechanics of Biological Tissue. Springer, Heidelberg, 2005. [2] G. A. Holzapfel. Computational biomechanics of soft biological tissue. In E. Stein, R. de Borst, and T. J. R. Hughes, editors, Encyclopedia of Computational Mechanics. Volume 2 Solids and Structures, pages 605– 635, Chichester, 2004. John Wiley & Sons. [3] T. C. Gasser and G. A. Holzapfel. Physical and numerical modeling of dissection propagation in arteries caused by balloon angioplasty. In M. H. Hamza, editor, Proceedings of the 3rd IASTED International Conference on Biomechanics, pages 229–233. ACTA Press, Anaheim, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
21
Recent Developments of Hybrid Crack Element: Determination of Its Complete Displacement Field and Combination with XFEM B.L. Karihaloo, Q.Z. Xiao School of Engineering, Cardiff University, Queen’s Buildings, The Parade, Newport Road, Cardiff CF24 3AA, UK
[email protected] (BL Karihaloo),
[email protected] (QZ Xiao)
ABSTRACT The hybrid crack element (HCE) [1] is one of the most accurate and convenient finite elements (FEs) for the direct calculation of the stress intensity factor (SIF) and coefficients of the higher order terms of the Williams expansion [2, 3]. It represents a crack by only one super-element which is connected compatibly with the surrounding elements. It is very efficient for analysing bodies with many cracks [4]. The HCE is formulated from a simplified variational functional using truncated asymptotic crack tip displacement and stress expansions and interelement boundary displacements compatible with the surrounding regular elements. In the implementation, a general FE mesh can be used by forming the HCE from elements surrounding the crack tip [5]. The HCE can thus be included in any commercial package as conveniently as normal hybrid stress elements. However, the exclusion of the rigid body modes in the truncated asymptotic displacements creates jumps between these displacements and element boundary displacements. In this study, the rigid body modes are recovered by minimising these jumps via a least squares method. If the HCE only is used, the part of the crack inside the HCE need not conform to the mesh. However, crack faces away from the crack tip (outside the HCE) need to conform to the mesh. This disadvantage can be avoided by combining the HCE with the extended FEM (XFEM) [6]. The XFEM enriches the standard local FE approximations with a displacement discontinuity across a crack, and the asymptotic solution at the crack tip, with the use of the partition of unity (PU). It avoids using meshes conforming with the discontinuity and also adaptive remeshing as the discontinuity grows as is the case with the FEM. XFEM offers great flexibility in the modelling of the fracture process. However, the accuracy of the displacements and/or stresses in a few layers of elements surrounding the crack tip is low. The combined method using both HCE and XFEM inherits the flexibility of the XFEM and the high accuracy of the HCE. Typical static and propagating crack problems will be presented to demonstrate the efficiency and accuracy of this method.
References [1] P. Tong, T.H.H. Pian, S.J. Lasry, A hybrid element approach to crack problems in plane elasticity. Int J Numer Meth Engng, 7, 297-308, 1973. [2] B.L. Karihaloo, Q.Z. Xiao, Accurate determination of the coefficients of elastic crack tip asymptotic field by a hybrid crack element with p-adaptivity. Engng Fract Mech, 68, 1609-30, 2001. [3] Q.Z. Xiao, B.L. Karihaloo, X.Y. Liu, Direct determination of SIF and higher order terms of mixed mode cracks by a hybrid crack element. Int J Fract, 125, 207-25, 2004. [4] D. Zeng, N. Katsube, J.M. Zhang, W. Soboyejo, Hybrid crack-tip element and its applications. Finite Elem Anal Des, 38, 319–35, 2002. [5] B.L. Karihaloo, Q.Z. Xiao, Implementation of HCE on a general FE mesh for interacting multiple cracks. Proc ECCOMAS 2004. Jyväskylä, Finland, 24 - 28 July, 2004. CD-ROM. [6] N. Moës, J. Dolbow, T. Belytschko, A finite element method for crack growth without remeshing. Int J Numer Meth Eng, 46, 131-150, 1999.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
22
Structural Model Validation and the Lack-of-Knowledge Theory Pierre Ladevèze *,†, Paul Enjalbert *, Guilllaume Puel •, Thierry Romeuf ռ *
LMT-Cachan (ENS Cachan/CNRS/Paris 6 University) 61 avenue du Président Wilson, F-94235 Cachan Cedex, France {pierre.ladeveze,paul.enjalbert}@lmt.ens-cachan.fr †
EADS Foundation Chair Advanced Computational Structural Mechanics • LMMSMat (École Centrale Paris/CNRS) Grande Voie des Vignes, F-92295 Châtenay-Malabry Cedex, France
[email protected] ռ EADS Space Transportation Route de Verneuil BP96, F-78133 Les Mureaux Cedex, France
[email protected]
ABSTRACT Today, the validation of complex structural models - i.e. the assessment of their quality compared to an experimental reference - remains a major issue. Most advanced approaches rely on the updating of deterministic dynamic parameters (stiffness, mass, damping) based on free or forced vibration tests. Uncertainties and probabilistic models can also be taken into account. In these works, the model validation is performed in a restricted sense. The true validation problem should be addressed through the comparison between the model - whether deterministic or not - used classically and the complete reality: such an issue raises philosophical questions. Here, we introduce a tentative answer through the Lack-Of-Knowledge (LOK) Theory, whose aim is to ”model the unknown”. In a certain way, this can be interpreted as an extension of what design engineers do when they introduce safety factors. Of course, the theory takes into account all the sources of uncertainties, including modeling errors, through the concept of basic LOKs. So far, two types of basic LOKs have been introduced: stiffness and excitation. For example, the structure being considered as an assembly of substructures, the basic stiffness LOKs are defined on the substructure level: each LOK is a scalar internal variable which quantifies the substructure’s LOK state in terms of structural stiffness; in mathematical terms, this variable is bounded by two stochastic bounds which follow probabilistic laws. Finally, a set of basic LOKs is added to the classical model to constitute the true model. This leads to an envelope of the actual responses; in particular, we can derive for the whole structure the effective LOK of a quantity of interest D, resulting in an interval with stochastic bounds. Another major question is the reduction of the LOKs using additional experimental information; the starting point could be an overestimated initial LOK level coming from experience. The paper focuses on the basic ideas of the Lack-Of-Knowledge Theory and on its first applications. Academic examples as well as industrial cases will be presented.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
23
Modeling of Historical Masonry with Discrete Elements J. V. Lemos Laboratório Nacional de Engenharia Civil (LNEC) Av. do Brasil, 101, 1700-066 Lisboa, Portugal
[email protected]
ABSTRACT Masonry is an inherently discontinuous material, formed by various components (stones, bricks, mortar), and its mechanical behavior reflects this internal structure. Engineering modeling of masonry structures is often based on continuum representations, using appropriate constitutive models, which provide an adequate solution for many practical cases. However, discontinuum models, which attempt to represent more closely the masonry components, are today applied with increasing frequency. They are preferred in research studies intended at understanding the mechanical behavior of masonry structures, but they are now also applied in engineering analysis, as the progress in computational resources is making them more accessible. Discontinuum representations may be achieved with various formulations of finite element methods. The present paper focuses on discrete elements models, a designation that covers a variety of representations of a structure as a system of blocks (rigid or deformable) or particles. Simplified contact formulations are generally used, to allow the analysis of very large systems, and explicit large displacement algorithms are employed. The paper discusses, in particular, two types of discrete element model, in relation to the specific requirements of masonry analysis. The first type is block models (rigid or deformable), which have proved very effective in the seismic analysis of historical stone masonry structures. Several applications are reviewed and key issues arising in this field are addressed, namely the variability of response observed in rigid block dynamics and the simplifications required in the analysis of large or complex structures. The second type of discrete element models examined is circular particle models, which represent each masonry block as a set of disks linked by contacts with tensile and shear bonds. Particles may also be used to simulate mortar or infill, and contacts between the various components are assigned appropriate constitutive behavior. An example of analysis of a multi-leaf wall is presented. The potential uses of these models in the study of the fundamental mechanics of masonry, in particular irregular masonry constructions, are discussed.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
24
A Regularized Strong-form Meshfree Method for Adaptive Analysis G.R. Liu, Bernard B.T. Kee Centre for ACES, Department of Mechanical Engineering, National University of Singapore, 9 Engineering Drive 1, Singapore 117576
[email protected];
[email protected]
ABSTRACT This talk presents an adaptive meshfree method which is based on strongform formulation and does not use any mesh predefined through node connectivity. In this present formulation, a radial point collocation procedure is used to discretize the system governing equations. Techniques are presented to stabilize the solution to obtain stable and accurate results. Adaptive scheme adopted in this work uses an error indicator based on residuals. Simple and practical refinement procedures are also presented for additional node insertion at each adaptive step. Numerical examples are presented to demonstrate that the proposed adaptive meshfree method can obtain efficiently stable solutions of desired accuracy.
References [1] G. R. Liu and Y. T. Gu, An introduction to meshfree methods and their programming, Springer, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
25
Multiresolution Analysis for Material Design Wing Kam Liu Department of Mechanical Engineering, Northwestern University, Evanston, IL, 60208
[email protected]
ABSTRACT The relationship between material microstructure and properties is the key to optimization and design of lightweight, strong, tough materials. Material properties are inherently a function of the microscale interactions at each distinct scale of deformation in a material. Currently, we rely on empirical data to define the structure-property link in the material design chain. A model is proposed here in which a material is physically and mathematically decomposed to each individual scale of interest. Material deformation can subsequently be resolved to each of these scales. Constitutive behavior at each scale can be determined by analytically or computationally examining the micromechanics at each scale. The proposed multiresolution technique is capable of linking overall material properties to the underlying microstructure via the micromechanics at each scale of interest. The small scale deformation phenomena which have a profound impact on macroscale properties are captured. The technique is general enough to be used in any material which exhibits different constitutive behavior at each scale. It can be implemented in a general finite element framework. This is illustrated for a polycrystalline material, a granular material, an alloy containing particles at two scales. A potential use for a bio-inspired self healing composite is also discussed. The theory can then be applied computationally in a finite element framework to determine the overall material properties in terms of the constitutive behavior at each scale, without resorting to empiricism.
References [1] Cahal McVeigh, Franck Vernerey, Wing Kam Liu and L. Cate Brinson, Multiresolution Analysis for Material Design, To appear in the special issue of Computer Methods in Applied Mechanics and Engineering, in memory of Professor J H Argyris. [2] S. Li, W.K. Liu, Meshfree Particle Methods, Springer (2004) [3] S. Hao, W.K. Liu, C.T. Chang, Computer Implementation of Damage Models by Finite Element and Meshfree Methods, Computational Methods for Applied Mechanics and Engineering 187, (2000) 401-440 [4] S. Hao, W.K. Liu, B. Moran, F. Vernerey, G.B. Olson, Multi-scale constitutive model and computational framework for the design of ultra- high strength, high toughness steels, Computer Methods in Applied Mechanics and Engineering 193 n17-20 (2004) 1865-1908 [5] F. Vernerey, W.K. Liu, B. Moran, Continuum theory for multi- scale micromorphic materials, Northwestern University Report, Illinois (2005) [6] H. Kadowaki, W.K. Liu, Bridging Multiscale method for localization problems, Computer methods in applied mechanics and engineering, 193 (2004) 3267-3302 [7] L.C. Brinson, One Dimensional Constitutive Behavior of Shape Memory Alloys: Thermomechanical derivation with non-constant material functions, Journal of Intelligent Material Systems and Structures 4(2) (1993) 229-242 [8] W.K. Liu, E.G. Karpov, S. Zhang, H.S. Park, An introduction to computational nanomechanics and materials, Computer Methods in Applied Mechanics and Engineering, 193 n17-20 May (2004) 1529-1578
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
26
Characterization and Multiscale Modeling of Asphalt - Recent Developments in Upscaling of Viscous and Strength Properties Roman Lackner*, Ronald Blab†, Josef Eberhardsteiner*, and Herbert A. Mang* *
Institute for Mechanics of Materials and Structures, Vienna University of Technology (TU Wien) Karlsplatz 13/202, 1040 Vienna, Austria {Roman.Lackner,Josef.Eberhardsteiner,Herbert.Mang}@tuwien.ac.at †
Institute for Road Construction and Maintenance, Vienna University of Technology (TU Wien) Gußhausstraße 28/233, 1040 Vienna, Austria
[email protected]
ABSTRACT The assessment and prediction of the performance of multi-composed materials, such as e.g. asphalt, requires suitable procedures for identification of their mechanical properties. In case of asphalt used for trafficked pavements, these properties vary with the underlying mix design (volume fractions and used constituents) and additives (e.g., polymers). In the past, the mix design and the allowance of additives were optimized, aiming at (a) a low viscosity at high temperatures (T > 135 °C) for the construction and compaction process of high-quality asphalt layers, (b) a significantly higher viscosity at medium temperature in order to minimize the development of permanent deformations (rutting), and (c) sufficient relaxation behavior at sub-zero temperatures, avoiding low-temperature cracking (see failure modes in Figure (left)). Motivated by the large variety of asphalt mixtures resulting from this optimization process and the necessity of predicting the future performance of pavements, a multiscale model for asphalt is currently developed at TU Wien. It relates macroscopic properties to finer-scale information (such as volume fractions, morphology, and the behavior of material phases) by introducing, in addition to the so-called macroscale (i.e., the scale at which prediction analyses are performed), four finer scales of observation, ranging down to the so-called bitumen-scale (see Figure (right)).
Figure: (left) failure modes in asphalt pavements and (right) multiscale model for asphalt In this lecture, recent results on upscaling information from finer observation scales towards the macroscale are presented. For this purpose, both analytical methods (continuum micromechanics) and numerical schemes (limit analysis) are employed. In addition to the theoretical work, the presented multiscale model for asphalt requires a significant amount of experimental work, covering both the identification of properties of material phases at the different observation scales and the validation of the employed upscaling schemes. Test results as well as advanced test methods employed at the Christian Doppler Laboratory for “Performance-based optimization of flexible pavements” at TU Wien for the characterization of asphalt at different scales are presented.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
27
Dissipative Interface Modeling for Vibroacoustic Problems - A New Symmetric Formulation ¨ Walid Larbi, Roger Ohayon Jean-Franc¸ois Deu, Structural Mechanics and Coupled Systems Laboratory Conservatoire National des Arts et M´etiers Chair of Mechanics - case 353 292 rue Saint-Martin, 75141 Paris Cedex 03, France
[email protected]
ABSTRACT This work concerns the variational formulation and the numerical computation of vibroacoustic interior problems with interface damping. The coupled system consists of an elastic structure (described by a displacement field) containing an inviscid, compressible and barotropic fluid (described by a pressure field), gravity effects being neglected. Within the context of noise reduction techniques, we propose to investigate the effect of introducing a thin layer of damping material at the fluid-structure interface. The originality of this work lies in the introduction of an additional unknown field at the fluid-structure interface, namely the normal fluid displacement field [1, 2]. With this new scalar unknown, various interface damping models can be introduced in the variational formulation. Moreover, the associated finite element matrix system can be solved in frequency and time domains. Here, a Kelvin-Voigt rheological model is used to take into account the interface damping. For a given material, the damping parameters can be found from the experimental acoustic impedance in a particular frequency range [3]. Following the procedure developed in [4], the proposed variational formulation is written in a symmetric form through the introduction of a displacement potential of the fluid. Numerical examples are presented in order to validate and analyze the new formulation.
References [1] J.-F. De¨u, W. Larbi and R. Ohayon, Structural-acoustic vibration and transient problems with interface damping. Third M.I.T. Conf. on Computational Fluid and Solid Mechanics, 14-17 June, 2005, Cambridge, USA. [2] W. Larbi, J.-F. De¨u and R. Ohayon, A new finite element formulation for internal acoustic problems with dissipative walls. International Journal for Numerical Methods in Engineering, accepted for publication, 2006. [3] V. Kehr-Candille and R. Ohayon, Elastoacoustic damped vibrations – Finite element and modal reduction methods. P. Ladev`eze, O.C. Zienkiewicz eds. New Advances in Computational Structural Mechanics, Elsevier, Amsterdam, 321–334, 1992. [4] H.J.-P. Morand and R. Ohayon, Fluid-Structure Interaction. Wiley, New York, 1995.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
28
Seismic Design Procedures in the Framework of Evolutionary Based Structural Optimization Manolis Papadrakakis, Nikolaos D. Lagaros, Michalis Fragiadakis
Institute of Structural Analysis & Seismic Research, National Technical University of Athens 9 Iroon Polytechniou Str., Zografou Campus, 15780 Athens, Greece {mpapadra, nlagaros, mfrag}@central.ntua.gr
ABSTRACT Since the early seventies structural optimization has been the subject of intensive research and several different approaches have been advocated for the optimal design of structures in terms of optimization methods or problem formulation. Most of the attention of the engineering community has been directed towards the optimum design of structures under static loading conditions with the assumption of linear elastic structural behaviour. For a large number of real-life structural problems assuming linear response and ignoring the dynamic characteristics of the seismic action during the design phase may lead to structural configurations highly vulnerable to future earthquakes. Furthermore, seismic design codes suggest that under severe earthquake events the structures should be designed to deform inelastically due to the large intensity inertia loads imposed. The objective of this work is to evaluate various design procedures adopted by seismic codes and their influence on the performance of real-scale structures under an objective framework provided by structural optimization. Several studies have appeared in the literature where seismic design procedures based on non-linear response (e.g. [1,2]) are presented and compared. However, this task can be accomplished in a complete and elaborate manner only in the framework of structural optimization, where the designs obtained with different procedures can be directly evaluated by comparing the value of the objective function of the optimization problem and the seismic performance of the optimum solution achieved. In this work evolutionary methods are implemented [3-5] to address the optimization problem and replace the conventional trial and trial and adjustmentbased procedures.
References [1] Han SW, Wen YK, Method for reliability-based seismic design: Equivalent nonlinear systems, II: Calibration of code parameters. ASCE Journal of Structural Engineering, 123(3): 256-270, 1997. [2] Bazzuro P, Cornell CA, Shome N, Carballo JE. Three proposals for characterizing MDOF nonlinear response. ASCE Journal of Structural Engineering 1998; 124(11): 1281-1289. [3] Foley CM. Optimized performance-based design for buildings. In Burns S.A. (Ed.) Recent Advances in Optimal Structural Design, ASCE Publications, 2002: 169-240. [4] M. Fragiadakis, N.D. Lagaros and M. Papadrakakis, Performance based earthquake engineering using structural optimization tools, International Journal of Reliability and Safety, 2005. [5] M. Fragiadakis, N.D. Lagaros and M. Papadrakakis Performance-based optimum design of steel structures considering life cycle cost, Structural and Multidisciplinary Optimization, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
29
High-Fidelity Multi-Criteria Aero-Structural Optimisation using Hierarchical Parallel Evolutionary Algorithms L. F. González*, L. H. Damp*, J. Périaux** and K. Srinivas* *
**
The University of Sydney, Sydney, NSW 2006, Australia {gonzalez, lloyd.damp, ragh}@aeromech.usyd.edu.au
INRIA Sophia Antipolis, OPALE project associate and CIMNE/UPC Barcelona
[email protected]
ABSTRACT An emerging technique for the solution of Multi-criteria and Multidisciplinary Optimisation problems are Evolutionary Algorithms (EAs). This paper describes a parallel multi-criteria (multi-objective) evolutionary algorithms (PEAs) for aero-structural problems. The foundations of the algorithm are based upon traditional evolution strategies and incorporate the concepts of a multi-objective optimisation, hierarchical topology, asynchronous evaluation and parallel computing. The algorithm works as a black-box optimiser and has been coupled to several aerodynamic and aircraft conceptual design solvers. The paper describes the features of the method and the application of the method for aero- structural design problems. The coupling of the algorithm with a higher order panel method, a commercial FEA solver and an automated aerodynamic and structural mesh generation program is described. In this automated process the optimiser defines design variables for the automatic mesh generation program which defines and produces the external geometry of the wing (Root chord, tip chord, sweep, etc) and the internal geometry (number of spars, number of ribs skin thickness, etc). This geometry is then analysed by the aerodynamic solver and maps the pressure forces into the structural model. Single or multiple objectives can be defined by the optimiser to find non-dominated –Pareto optimal solutions or the Nash equilibrium. The parallel computing capabilities in combination with hierarchical levels of aerodynamic and FEA solvers are exploited to reduce computational expense. Comparisons will be presented between a traditional analytical approach -weakly couple, and a high fidelity –strongly coupled- approach for the aero-structural analysis of a high aspect ratio aircraft/UAV wing.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
30
Interaction of Shells and Membranes with Incompressible Flows Ekkehard Ramm∗, Christiane F¨orster∗, Malte Neumann∗, Wolfgang A. Wall† ∗
Institute of Structural Mechanics, University of Stuttgart Pfaffenwaldring7, 70569 Stuttgart, Germany {ramm,foerster,neumann}@statik.uni-stuttgart.de
†Chair of Computational Mechanics, Technical University of Munich
Boltzmannstraße 15, 85747 Garching, Germany
[email protected]
ABSTRACT For the dynamic behavior of lightweight structures like thin shells and membranes exposed to fluid flow the interaction between the two fields is often essential. Computational fluid-structure interaction provides a tool to predict this interaction and complement or eventually replace expensive wind tunnel experiments. Partitioned analyses techniques enjoy great popularity for the numerical simulation of these interactions. This is due to their computational superiority over simultaneous, i.e. fully coupled monolithic approaches, as they allow the independent use of suitable discretization methods and modular analysis software. We use, for the fluid, GLS stabilized finite elements on a moving domain based on the incompressible instationary Navier-Stokes equations, where the formulation guarantees geometric conservation on the deforming domain. The structure is discretized by nonlinear, three-dimensional shell elements. Commonly used sequential staggered coupling schemes may exhibit instabilities due to the so-called artificial added mass effect. As best remedy to this problem subiterations should be invoked to guarantee kinematic and dynamic continuity across the fluid-structure interface. Since iterative coupling algorithms are computationally very costly, their convergence rate is very decisive for their usability. To ensure and accelerate the convergence of this iteration the updates of the interface position are relaxed. The time dependent, ’optimal’ relaxation parameter is determined automatically without any user-input via exploiting a gradient method or applying an Aitken iteration scheme. A variety of numerical examples will show the capabilities of the presented methods.
References [1] Ramm, E., Wall, W. A.: Shell Structures - A Sensitive Interrelation between Physics and Numerics. International Journal for Numerical Methods in Engineering 60, 381-427, 2004. [2] Neumann, M., Tiyyagura, S.R., Wall, W.A., Ramm, E.: Robustness and Efficiency Aspects for Computational Fluid Structure Interaction. Proc. of the Second Russian-German Advanced Research Workshop on Computational Science and High Performance Computing, Stuttgart, Germany, March 14-16, 2005. In: Notes on Numerical Fluid Mechanics and Multidisciplinary Design (NNFM), Springer, 2005. ¨ [3] Forster , Ch., Wall, W.A., Ramm, E.: On the Geometric Conservation Law in Transient Flow Calculations on Deforming Domains. Int. J. Num. Meth. Fluids, 2005 (accepted).
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
31
Nonlinear Analysis of Composite and FGM Shells using Tensor-Based Shell Finite Elements J. N. Reddy* and R. A. Arciniega Advanced Computational Mechanics Laboratory Texas A & M University, College Station, TX 77843-3123 *
[email protected]
ABSTRACT In this paper, a finite element model for the nonlinear analysis of laminated shell structures and through-thickness functionally graded shells is presented. A tensor-based finite element formulation is presented to describe the deformation and constitutive laws of a shell in a natural and simple way by using curvilinear coordinates. In addition, a family of high-order elements with Lagrangian interpolations is used to avoid membrane and shear locking; no mixed interpolations are employed. A first-order shell theory with seven parameters is derived with exact nonlinear deformations and under the framework of the Lagrangian description. This approach takes into account thickness changes and, therefore, 3D constitutive equations are utilized. Numerical comparisons of the present results with those found in the literature for typical benchmark problems involving isotropic and laminated composite plates and shells as well as functionally graded plates and shells are found to be excellent and show the validity of the developed finite element model. Moreover, the simplicity of this approach makes it attractive for applications in contact mechanics and damage propagation in shells. Acknowledgement. The research results reported herein were obtained while the authors were supported by the Structural Dynamics Program of the Army Research Office (ARO) through Grant . 45508EG.
References [1] R.A. Arciniega, On a tensor-based finite element model for the analysis of shell structures, PhD dissertation, Dept. of Mechanical Engineering, Texas A&M University, December 2005. [2] J.N. Reddy, An Introduction to Nonlinear Finite Element Analysis, Oxford University Press, Cambridge, UK, 2004. [3] J.N. Reddy, Mechanics of Laminated Composite Plates and Shells: Theory and Analysis, 2nd edition, CRC Press, Boca Raton, Florida, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
32
Strength of Textile Composites – A Voxel Based Continuum Damage Mechanics Approach Raimund Rolfes*, Gerald Ernst*, Daniel Hartung†, Jan Teßmer† *
†
Institute for Structural Analysis, University of Hannover Appelstraße 9a, 30167 Hannover, Germany {r.rolfes, g.ernst}@isd.uni-hannover.de
Institute of Composite Structures and Adaptive Systems, DLR Braunschweig Lilienthalplatz 7, 38108 Braunschweig, Germany {jan.tessmer, daniel.hartung}@dlr.de
ABSTRACT Industrialised infusion processes enable a cost-effective possibility to produce textile composite structures compared to pre-impregnated composite systems (Prepregs). Particularly with regards to high performance structures one has to be familiar with the material behaviour and the failure characteristic to apply fibre reinforced composites profitable. In this publication a brief overview of the current research activities to characterise the mechanical behaviour, failure and strength of textile composites compared with prepreg systems is presented. Unlike pre-impregnated and filament winding composites, textiles are different in their mechanical behaviour due to various fibre architectures of the preforms (braided, woven, stitched, tufted, etc.). Therefore, a finite element analysis of a representative volume element (unit cell) on a micromechanical level is a promising possibility to analyse the mechanical behaviour and to predict the material failure. Currently different approaches are used to account for many material characteristics. The first results of an approach, which considers a continuum damage model to predict the first micromechanical material failure, will be presented. A lot of standards have been established to determine the material properties of Prepregs over the last years. Particularly textile composites require an adapted test setup to account for the characteristic material behaviour and to validate different failure criteria. The standards used to qualify a preimpregnated material and a short description of the requirements for textile composites are presented. While many failure theories were developed during the last years, there are some weaknesses even by the most popular failure theories. The results of the World Wide Failure Exercise have shown that there is a demand for an accurate failure prediction also for prepreg composites. Especially the comparatively complex failure of textile composites requires an advanced failure theory. The fracture plane concept originally proposed by Hashin is a promising method to describe the failure behaviour of prepreg composites. A three dimensional failure model was developed based on a fracture plane by Juhasz, who considers the characteristic material behaviour of orthogonally reinforced composites. This criterion was implemented in a three dimensional finite element to account for the three dimensional stress state in each layer of a lamina by Kuhlmann and Rolfes [1].
References [1] G. Kuhlmann and R. Rolfes, A hierarchic 3d finite element for laminated composites. International Journal for Numerical Methods in Engineering, 61, 96–116, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
33
Concrete at Early Ages and Beyond: Numerical Model and Validation Bernhard A. Schrefler*, Francesco Pesavento*, Dariusz Gawin†, Mateusz Wyrzykowski† *
Dept. of Structural and Transportation Engineering, University of Padova, Italy Via F. Marzolo 9, 34131 Padova - Italy
[email protected],
[email protected]
†
Dept. of Building Physics and Building Materials, Technical University of Lodz, Poland Al. Politechniki 6, 93-590 Lódz, Poland
[email protected]
ABSTRACT This work deals with a new mathematical/numerical model for the analysis of the behaviour of concrete considered as multiphase viscous porous material from early ages to long term periods. This is a solidification-type model where all changes of material properties are expressed as functions of hydration degree, and not maturity nor equivalent hydration period as in maturity-type models. A mechanistic approach has been used to obtain the governing equations, starting from micro-scale, by means of modified averaging theory, also called hybrid mixture theory, [1-2]. Constitutive laws are directly introduced at macroscopic level. An evolution equation for the internal variable, hydration degree, describes hydration rate as a function of chemical affinity, considering additionally to the existing models, an effect of the relative humidity on the process. The model takes into account full coupling between hygral, thermal and chemical phenomena, as well as changes of concrete properties caused by hydration process, i.e. porosity, density, permeability, and strength properties. Phase changes and chemical phenomena, as well as the related heat and mass sources are considered. Some examples showing possibilities of the model for analysis of autogenous self-heating and selfdesiccation phenomena, as well as autogenous shrinkage are presented and discussed. Creep processes are modelled considering concrete as viscous-elastic material with aging caused by solidification of non-aging constituent, i.e. solidification theory for the so-called basic creep [1-2]. A Kelvin-type chain has been chosen for the definition of the compliance function, which corresponds to an expansion of that function in a Dirichlet’s series. Shrinkage is defined using the effective stress principle, as usual in the mechanics of porous materials, and it is coupled to the creep model. In such a way it is possible to have creep strains even if the concrete structure is not externally loaded. Capillary shrinkage is, in fact, characterized from capillary tensions which can be seen as a sort of internal load for the microstructure of the material. A series of numerical computations compared to the experimental results are presented as validation of the model described above.
References [1] D. Gawin, F. Pesavento, B.A. Schrefler: Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. Part I: Hydration and hygro-thermal phenomena. Int. J. Num. Meth. Engng, in print. [2] D. Gawin, F. Pesavento, B.A. Schrefler: Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. Part II: Shrinkage and creep of concrete. Int. J. Num. Meth. Engng, in print.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
34
Uncertainty & Reliability Analysis of Structural Dynamical Systems Gerhart I. Schuëller Chair of Engineering Mechanics, Leopold-Franzens University, Innsbruck, Austria, EU.
[email protected]
ABSTRACT In this paper various methods to analyze structural systems under stochastic dynamic loading are qualitatively compared. While the Karhunen-Loève expansion proved to be advantageous when uncertainty estimation is required, (advanced) Monte Carlo simulation procedures are recommended for reliability estimates. The computational efficiency of the methods play an important role w.r.t. practical applications. A further quantitative benchmark study is recommend.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
35
Neural Networks: New Results and Prospects of Applications in Structural Engineering Zenon Waszczyszyn*†, Leonard Ziemianski† *
Cracow University of Technology, Institute of Computer Methods in Civil Engineering Warszawska 24, 31-155 Krakow, Poland
[email protected] †
Rzeszów University of Technology, Chair of Structural Mechanics W. Pola 2, 35-959 Rzeszów, Poland
[email protected]
ABSTRACT NN is a new computational tool for data processing and this tool can be characterized as a “data dependent and model free” approach. Other features of NNs correspond to their applicability in the analysis of nonlinear direct and inverse problems. NNs can also be used in hybrid systems as a complementary part to conventional computational methods, especially to FEM. The applications of the feed-forward, multilayer, error back-propagation NN, called for short BPNN (back-propagation NN), are discussed focusing on two fields: 1) BPNN as a new independent computational tool, 2) hybrid FEM/BPNN systems. All the considered applications are based on data taken from tests on laboratory models or measurements performed on natural scale buildings. BPNN applications are illustrated on four selected problems. The first one is related to soil-structure interaction caused by paraseismic excitations. The mappings of displacement response spectra DRSg o DRSb were performed, where: DRSg spectrum computed on the ground level at a monitored building, DRSb neurally predicted spectrum inside the building on the basement level. It was proved that the application of Kalman filtering for the training of a BPNN leads to much more exact approximation than the application of Rprop learning method. The second problem is related to the identification of placement of an additional mass fastened to a steel plate. The dynamic response corresponding to natural eigenfrequencies of the plate with the mass was used as the BPNN input. Satisfactory results for the parametric identification of the mass location were obtained due to addition of the Gaussian white noise to perturb a small number of measured dynamic responses and due to the application of cascade architecture of BPNNs. The third problem deals with the application of hybrid FEM/BPNN Monte Carlo method in the reliability analysis of steel cylindrical panels. The results of laboratory tests were explored to update the FE model which was then used to compute the patterns for the BPNN training and testing. The trained network was explored to rapid computation of Monte Carlo simulations of the panel ultimate load. It was shown that the hybrid approach enables us to predict the probability of reliable curve very efficiently. The fourth problem is related to the hybrid approach of the FE model updating. It is discussed on the example of a simple plane frame tested on laboratory models. In the formulated hybrid system a FE program was used for generating the training and testing sets of patterns. The trained BPNN was then explored in the inverse analysis for calibrating of control parameters values which well corresponded to the measured eigenfrequencies of the frame laboratory models. Using BPNNs in the hybrid updating of FE models makes it possible to eliminate the optimization procedure in the corresponding inverse analysis.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
36
Computational Railway Dynamics Torbjörn Ekevid∗ , Per Kettil† , Håkan Lane† , Nils-Erik Wiberg† ∗ School
of Technology and Design Växjö University 351 95 Växjö, Sweden
[email protected]
† Department of Applied Mechanics Chalmers University of Technology 412 96 Göteborg, Sweden {per.kettil; hakan.lane; nils-erik.wiberg}@sem.chalmers.se
ABSTRACT High-quality and efficient means of transport is of high priority in the modern society. Railway traffic is environment friendly and economically very competitive for both freight and personal transports at mid-range distances. Although the railway technology has been improved substantially during the last decades, generated vibrations still impose annoyances to the surroundings environment and leads to deterioration of the track structure. To understand the physical phenomena and propose countermeasures/improvements, simulation tools to perform computations of the entire dynamical system including subground, track structure and the railway vehicle has been developed. In particular, large effort has been devoted to the special wave propagation problem related to high-speed trains running at soft ground materials. As the speed of the train approaches and exceeds the natural (Rayleigh) wave propagation velocity of the ground material, shock waves similar to sonic boom originates from the onrushing train. The problem area contains several computational challenges since it impose techniques to handle non-reflecting boundaries[1], time integration of large-scale problems, non-linear material response etc. Efficient solvers based on a combination of multigrid[2], error estimations and adaptive refinement has been developed to reach acceptable execution times. The solution time is substantially reduced compared to conventional implicit solvers based on factorization. Moreover, indefinite system from the Lagrange multiplier[3] approach to handle constraint equations imposes additional preconditioning to guarantee convergence and reducing the number of iterations. In the paper a number of numerical examples from railway applications are presented. Results from computation where the train is represented as a collection of moving loads as well as a multi body system with complete train-track interaction are demonstrated.
References [1] T. Ekevid, N.-E. Wiberg, Wave propagation related to high-speed train - a scaled boundary FEapproach for unbounded domains, Comput. Methods Appl. Mech. Engrg. 191, 3947–3964, 2002. [2] U. Trottenberg, C. Oosterlee, A. Schüller, Multigrid, Academic Press, London, 2001. [3] Z.-H. Zhong, Finite element procedures for contact-impact problems, Oxford Univ. Press, Oxford, 1993.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
37
Micro-Meso-Macro Modelling of Composite Materials P. Wriggers, M. Hain Institute of Mechanics and Computational Mechanics University of Hannover Appelstr. 9a, D-30167 Hannover, Germany
[email protected]
ABSTRACT Multi-scale models can be extremely helpful in the understanding of complex materials used in engineering practice. In the presentation the basic theoretical strategy is developed. Possible finite element methods to solve such problems are explained in detail and discussed. These are based on homogenization techniques but also on true multi-scale solutions. The developed methodology is then applied to a specific engineering material which is concrete. This construction material has to be investigated on three different scales, the hardened cement paste, the mortar and finally the concrete. Here a successive two-stage approach is followed in which first the multi-scale model of the cement paste and mortar is applied. The resulting homogenization can then used in a multi-scale mortar-concrete model. The model for the hardened cement paste is based on a three–dimensional computer–tomography at the micrometer length scale. For this a finite element model is developed with different constitutive equations for the three parts unhydrated residual clinker, pores and hydrated products. The volume fraction of the hydrated products is approximately 84 Vol.%. For this part, a visco–plastic material model of Perzyna-type including damage is applied. The other two parts are described with a linear– elastic material model. The constitutive equations at the micro–scale contains inelastic parameters, which cannot be obtained through experimental testings. Therefore, one has to solve an inverse problem which yields the identification of these properties. For computational efficiency and robustness, a combination of the stochastic genetic algorithm and the deterministic Levenberg-Marquardt method is used. In order to speed-up the computation time significantly, a client-server based system is used. Hence, all calculations are distributed automatically within a network environment. The resulting constitutive parameters on the micro-scale are then used in the homogenized constitutive model for the mortar. But also in the multi-scale model for the mortar. Both results are compared with each other but also with experimental data. A further interesting application occurs when the micro-structure of the cement paste is filled partly with water and a freezing process takes place. Due to frost, the moisture inside the microstructure freezes. A constitutive model for ice is applied to the water filled parts of the microstructure is then developed. The expansion of the ice leads to damage in the micro–structure which yields an inelastic material behavior on the macro–scale. If such a calculation is performed for different moistures and temperatures, a correlation between moisture, temperature and the inelastic material behavior is obtained. Numerical examples show, that the developed approach reproduces the material behavior realistically.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
38
An Object-Oriented Approach to High Order Finite Element Analysis of Three-Dimensional Continua M. Baitsch∗, T. Sikiwat, D. Hartmann∗ ∗ Department of Civil Engineering
Ruhr-University of Bochum, Germany
[email protected] [email protected] ABSTRACT It has been shown recently that the p-version of the finite element method is well suited for the analysis of thin walled three-dimensional continua [2]. However, designing and implementing software for the p-version of FEM is a challenge because of the increased complexity compared to the h-version. In this paper, we present an object-oriented finite element system implemented in Java. It is pointed out how the object-oriented paradigm, suitable design patterns and thorough unit testing can help to develop and maintain a complex engineering application. The basic idea of the software design is to separate generally applicable mathematical concepts, like basis functions and geometrical mappings from concrete element formulations that contain the physics of the actual problem. In the mathematical package, there are interfaces representing the concepts of basis functions (forming an Ansatz space) and functions defined on R1 , R2 and R3 . Several concrete classes implement these basic interfaces and realize for instance Lagrangian basis functions, hierarchical basis functions, functions constructed by a linear combination of basis functions or functions constructed by the blending function method. The use of NURBS curves hereby allows for the representation of complex geometries like that of the shell structure shown below. The power of this approach lies in the fact that on the element level only the interface types are used. Thus, an element formulation solely contains the physics and is not limited to a certain type of Ansatz space. Also, new Ansatz spaces can be easily incorporated lateron. Generally Java is considered as being slow for numerically intense applications. On the other side there are many advantages that make Java attractive also for simulation software [1]. In this paper, a hybrid approach is presented where the overall program is implemented in Java but numerically intense linear algebra operations are delegated to native code. In the full paper, it is shown that the software can be easily applied to problems involving 75 000 DOFs and more.
Analysis of a Shell Structure: System and Deformation
References [1] R.F. Boisvert, J. Moreira, M. Philippsen, and R. Pozo. Numerical computing in Java. Computing in Science and Engineering, 3(2):18–24, 2001. [2] A. D¨uster, H. Br¨oker, and E. Rank. The p-version of the finite element method for three-dimensional curved thin walled structures. International Journal for Numerical Methods in Engineering, 52:673–703, 2001.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
39
A finite element formulation based on the theory of a Cosserat point – Extension to Ogden material Eiris F.I. Boerner , Dana S. Mueller-Hoeppe , Stefan Loehnert , Peter Wriggers Institute for Mechanics and Computational Mechanics University of Hannover, Appelstrasse 9a, 30167 Hannover, Germany
[email protected] Department of Mechanical Engineering Northwestern University, 2145 Sheridan Road, Evanston, IL 60208, USA ABSTRACT The theory of Cosserat points is the basis of a finite element formulation for a solid three-dimensional continuum, which was presented by [1]. Previous investigations [2] have revealed, that this formulation is free of showing undesired locking or hourglassing-phenomena. It additionally shows excellent behaviour for large deformations in any type of incompressible material and for sensitive structures such as plates or shells. Within the theory of Cosserat points, the position vectors X and x of an 8-node-brick element are described through director vectors Di and di .
X=
7 i=0
N i (θ 1 , θ 2 , θ 3 )Di
,
x=
7
N i (θ1 , θ 2 , θ3 )di
i=0 3 4
N 0 = 1, N 1 = θ 1 , N 2 = θ 2 , N 3 = θ , N = θ1 θ2 , N 5 = θ1 θ3 , N 6 = θ2θ3 , N 7 = θ1 θ2 θ3 The special choice of shape functions N i allows to split the deformation as well as resulting stresses into homogeneous and inhomogeneous parts respectively. The stresses due to the inhomogeneous part of the deformation are obtained by incorporating analytical solutions to the deformation modes bending, torsion and higher-order hourglassing for a rectangular parallelepiped shaped reference element, see [1] and [2]. This work shows approaches on how to overcome the difficulty of initially distorted element geometries that differ strongly from the shape of a rectangular parallelepiped. The formulation initially was restricted to a Neo-Hookean material. This work will present the extension to a general elastic Ogden material as well as to metal plasticity for large deformations with isotropic hardening. It will also give insight to the properties of the Cosserat point element and its behaviour for rubber-like materials.
References [1] Nadler, B.; Rubin, M.B. (2003), A new 3-D finite element for nonlinear elasticity using the theory of a Cosserat point, Solids & Structures, 40, 4585-4614. [2] Loehnert, S.; Boerner, E.F.I.; Rubin, M.B.; Wriggers, P. (2005), Response of a nonlinear elastic general Cosserat brick element in simulations typically exhibiting locking and hourglassing, Computational Mechanics, Vol. 36:266-288.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
40
A macro tetrahedral element with vertex rotational D.O.F.s Jaesung Eom*, Byungchai Lee† *
Department of mechanical engineering, Korea advanced institute of science and technology, 373-1 Guseong-dong, Yuseong-gu, Daejon, 305-701, Republic of Korea
[email protected]
†
Department of mechanical engineering, Korea advanced institute of science and technology, 373-1 Guseong-dong, Yuseong-gu, Daejon, 305-701, Republic of Korea
[email protected]
ABSTRACT In this study, a macro tetrahedral element with vertex rotations is presented with the systematic macro element fabrication and the inclusion of proper higher-order deformation modes. The individual element test (IET) proved sub-tetrahedral elements are basically combined for the macro element. During the construction of the macro element, a higher-order stiffness is emerged by moving the influence of removed virtual node stiffness into the deformation modes which are related to the vertex rotations. The fundamental decomposition into a basic stiffness and a higher-order stiffness allows scaling the performance of the macro element. To fulfill the accuracy and stability requirement of the element, the transformation between hierarchical rotations and nodal freedoms is employed to separate rotational freedoms into the constant strain related rotation and the higher-order behavior related one. Each parameter in the element stiffness is tuned through beam-type higher order patch test. The numerical performance of the proposed element is compared with other solid elements with vertex rotation in the benchmark test problem.
References [1] K.Y. Sze and Y. S. Pan, Hybrid stress tetrahedral elements with Allman’s rotational D.O.F.s, International journal for numerical methods in engineering, 48, 1055-1070, 2000. [2] Carlos A. Felippa, A study of optimal membrane triangles with drilling freedoms. Computer methods applied mechanicultibody System Dynamics, 1, 149-188, 1997. [3] P. G. Bergan and L. Hanssen, A new approach for deriving ‘good’ finite elements, Proc. MAFELAP II Conf., Academic Press, Brunel University, 483-497, 1976. [4] Jaesung Eom and Byungchai Lee, A study of a macro membrane triangle with drilling freedoms, Proc. WCCM VI Conf., Tsinghua University Press & Springer-Verlag, 23, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
41
Application of aggregation multilevel iterative solver to problems of structural mechanics Sergiy Yu. Fialko* *
National University of Architecture and Constructions in Kiev, Ukraine & Software Company SCAD Soft 4, I. Klimenko str., Office 20 Kiev, Ukraine, 03037
[email protected]
ABSTRACT The application of aggregation multilevel iterative solver AMIS [2, 3] to the structural analysis of large-scale finite element problems is discussed. It is well-known that such problems usually are poorly conditioned and this leads to slow convergence of iterative methods [1]. The preconditioned conjugate gradient method with aggregation multilevel preconditioning is applied to solution the both: linear static problems and natural vibration ones. The effectiveness of several solution stages is considered: the creation of aggregation model, the application of sparse matrix technique to solution of the coarsest level problem, the smoothing algorithms and so on. The set of local rigid links are imposed to the given finite element model to decrease the number of degrees of freedom. The nodeby-node or element-by-element approaches are applied to obtain the reduced model on coarsest level. We try to keep as large number of equation on coarsest level as the computer resources permits it to do. The block sparse multifrontal solver [4] is applied to solve the coarsest level problem. The proper reordering method among multilevel reordering and multiple minimum degrees ones is chosen to reduce fill-inns. The several modifications of incomplete Cholesky factorization approaches are applied to smooth rapidly oscillating residuals after prolongation. The numerous numerical examples, taken from computational practice of SCAD Soft, illustrate the robustness and efficiency of proposed method.
References [1] A. Perelmuter, S. Fialko. Problems of computational mechanics relate to finite-element analysis of structural constructions. International Journal for Computational Civil and Structural Engineering, 1(2) 72-86, 2005. [2] S. Fialko. Application of iterative solvers in finite element analysis of structural mechanics. Linear statics and natural vibrations. Proceedings of 8-th international conference "Modern building materials, structures and techniques". May 19–22, 2004, Vilnius, Lithuania. P. 721 – 725. [3] S. Fialko. Aggregation multilevel iterative sSolver for analysis of large-scale finite element problems of structural mechanics: linear statics and natural vibrations. R.Wyrzykowski et al. (Eds.): PPAM 2001, LNCS 2328, pp. 663 –670, 2002. Springer-Verlag Berlin Heidelberg 2002.
[4] S. Fialko. A block sparse direct multifrontal solver in SCAD software. Proceedings of the CMM-2005 – Computer Methods in Mechanics. June 21-24, 2005, Czestochowa, Poland. 73 – 74.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
42
Convergence Analysis of a Domain Decomposition Method with Augmented Lagrangian Formulation Alexandre Santos Hansen*, Fernando Alves Rochinha† * Petrobras/ENGENHARIA/IEEPT/EEPTM/EDI Rua Almirante Barroso, 81, 11º.andar, Rio de Janeiro, RJ, 21031-004, Brasil
[email protected] †
Dept. de Engenharia Mecânica – COPPE - UFRJ Cx. 68503, 21945-970, Rio de Janeiro, RJ, Brasil
[email protected]
ABSTRACT Through the combination of an augmented Lagrangian formulation with a preconditioned inexact Uzawa algorithm, we construct a domain decomposition based method for finite element approximation of linear second-order elliptic partial differential equations. With this approach, the proposed method shares the main features of Lagrange multipliers based domain decomposition methods, i.e. number of iterations bounded by the local element size (H/h) using a simple coarse space and direct application to decompositions with irregular sub domain geometry, with the advantage that inexact solvers at sub domain level are allowed at sub domain level. An analysis of the method applied to the Poisson equation is presented to justify the preconditioners choices and to derive bounds for the convergence factor in function of the local element size.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
43
Computational Models on Graphs for Nonlinear Hyperbolic and Parabolic System of Equations Yaroslav A. Kholodov1, Alexander S. Kholodov2, Nikolai V. Kovshov3, Sergey S. Simakov4, Dmitri S. Severov5, Alexey K. Bordonos6, Azilkhan Bapayev7 1-4,6,7 Moscow Institute of Physics and Technology 9, Institutski Line, Dolgoprudny City, Moscow Region, 141700, Russia 1
[email protected], 2
[email protected], 3
[email protected], 4
[email protected], 6
[email protected], 7
[email protected] 5 Open Technologies company Bld. 1, 30, Obrucheva str., Moscow, 117997, Russia 5
[email protected]
ABSTRACT For G GgraphG edge G each G with length X k we consider 1D nonlinear hyperbolic system of equations vGt Fxk (v )G f , v {v1 ,..., v I } , t t 0 , 0 d xk d X k , k 1,..., K (1) with initial conditions v (0, xk ) v 0 ( xkG) , k 1,..., K and the next boundary conditions: for graph enters (l 0 1,... L0 , xk 0G) M li0 (t , v (t , 0)) 0 , i 1,..., rk0 d I (2) , for graph exits (l * 1,...L* , xk X k ) Mli* (t , v G(t , X i 1,..., rk* d I (3) and for graph branchpoints l 1,..., L G k )) G0 , \ lm (t , wl , vl1 ,..., vlM l ) 0 m 1,..., M l (4). Here K is the number of graph edges, L0 - enters, L* th exits, G GL - branchpoints, M l - incoming and outgoing graph edges forG the l branchpoint, vl1 ,..., vlM l - required vectors in theG ends of edges adjoining to branchpoin l , wl - required vector for G the branchpoint l . The matrix wF / wv A {aij } i, j 1,..., I is Jacobi matrix and we can apply 1 the identity A : /: , where / {Oi } is the diagonal matrix of the matrix A eigenvalues, : is the nonsingular matrix whose rows are linearly independent left-hand eigenvectors of the matrix A ( Det: z 0 ) and : 1 is the matrix inverse to : . G ToG enclose Gboundary Gconditions (2)-(4) we can use compatibility conditions Zi dv dti 0 , ( dv / dti wv / wt Oi wv / wxk ), i 1,..., I along the characteristics of the system (1) dx Oi dt directed inside integration domain. These compatibility conditions can be used to analyze correctness of the problem definition for system (1) through the all graph segments. The main idea of this approach is that the solution of the global 3D problem for the whole graph can be split out on the set of the 1D problem for the single graph elements (edges). Then on the each step of numerical integration we join these 1D problems by the additional equation systems in the graph nodes to get the common solution for the original problem. By this way we guarantee the global coupling for the all original problem variables. The same computational model can be applied for nonlinear parabolic equations. The numerical results are presented for the problem solution on the different graph systems: The global numerical models of blood circulation in the human body. The model of global regional electrical power systems. The model of bar structures and frames behavior under the different impacts. The model of the intensive information flows in the computer networks. The model of heavy traffic in the big cities. The model of flood water and pollution propagation in the large river systems.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
44
Haar wavelet method for solving integral equations and evolution equations Ülo Lepik Institute of Applied Mathematics, University of Tartu Liivi 2, 50409 Tartu, Estonia
[email protected]
ABSTRACT An efficient numerical method for solving nonlinear integral equations and evolution equations based on the Haar wavelets approach is proposed. The method is tested for Fredholm and Volterra integral equations and for the Burgers and sine-Gordon equations. Results obtained by computer simulation are compared with other available solutions. These calculations show that the accuracy of the Haar wavelet approach is quite high even in the case of a small number of grid points.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
45
A new approach for elimination of dissipation and dispersion errors in particle methods Hassan Ostad-Hossein*, and Soheil Mohammadi† *School of Civil Engineering, University of Tehran,Tehran, Iran
[email protected] † School Civil Engineering, University of Tehran,Tehran, Iran
[email protected]
ABSTRACT Numerical errors may be introduced in some numerical methods of solving differential equations because of their nature. Discretizing a continuum medium would result in changing the wave velocity and inducing numerical errors into the solution. Some methods using strong formulations are based on the Taylor expansion. Therefore, using only a finite number of Taylor series terms for particle simulations introduces truncation errors. Truncation of the Taylor expansion is also the reason for developing two other types of error. The first, called dispersion error appears in the form of extra vibration in high frequency modes that can result in solution instability in some problems. Another type of error is dissipation and may cause decrease in wave amplitude. Particle methods such as SPH [1] and CSPM [2], are also involved with truncation errors. A number of methods have already been proposed for removing dispersion from particle methods such as adding artificial stress. However these methods become energy dissipative resulting in wave amplitude decays after several time steps. In this paper further investigation is performed to study the roots of dispersion and dissipation errors in particle methods. A new procedure is proposed for eliminating dispersion and stabilizing the solution, based on the CSPM particle method and the Newmark time integration scheme. The results are compared with other existing methods.
REFERENCES [1] Chen JK, Beraun JE, Jih CJ, An improvement for tensile instability in smoothed particle hydrodynamics, Comput. Mech. 23 (1999a) 279-287 [2] Chen JK, Beraun JE, Jih CJ, Completeness of corrective smoothed particle method for linear elastodynamics, Comput. Mech. 24 (1999b) 273-285 [3]Chen JK, Beraun JE, Jih CJ, A corrective smoothed particle method for transient elastoplastic dynamics, Comput. Mech. 27 (2001) 177-187 [4] M.B. Liu, G.R. Liu, Z. Zong, Constructing smoothing functions in smoothed particle hydrodynamics with applications, Journal of Computational and applied Mathematics, 155 (2003) 263-284 [5] Gray J.P., Monaghan J.J., Swift R.P., SPH elastic dynamics, Comput. Methods Appl. Mech. Engrg 190 (2001) 6641-6662
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
46
Solution of stability problem of infinite plate strips Zdzisław Pawlak*, Jerzy Rakowski† *
Institute of Structural Engineering, Poznan University of Technology ul. Piotrowo 5, 60-965 Poznań, Poland
[email protected]
†
Institute of Structural Engineering, Poznan University of Technology ul. Piotrowo 5, 60-965 Poznań, Poland jerzy.rakowski@ put.poznan.pl
ABSTRACT The aim of the paper is to solve a stability problem of infinite plate strips using the finite strip method (FSM). Contrary to well-known solutions for 2D continuous systems the authors present an idea for solving a stability problem of infinite discrete plates. A continuous plate strip simply supported on its opposite edges is divided into a regular mesh of identical finite strips. According to the finite strip procedure the field of loading and displacement functions are expressed in the form of harmonic series [1]. Stiffness and geometrical matrices for a four-degree-of-freedom finite strip are determined. The unknowns are deflections and transverse slope amplitudes along the nodal lines. Equilibrium conditions are derived from the FSM formulation. An infinite set of linear equations being the equilibrium conditions for each nodal line is expressed in the form of two second-order difference equations [2]. For a regular discrete system these equations written in the recurrent form are equivalent to the FSM matrix formulation. The exact solution of these difference equations is found in an analytical form. The displacement function fulfils the boundary conditions of the analysed plate strip and is given as a discrete expression for an arbitrary nodal load [3]. The solution of eigenvalue problem of the difference equations enables one to determine the critical forces of the structure. The main advantage of the presented approach is the analytical form of the solution obtained in the discrete domain. This enables a detailed parametrical analysis and investigations of the influence of geometrical and physical properties on the critical force value.
References [1] Y. C. Loo, A. R. Cusens, The Finite Strip Method in Bridge Engineering, New York, Viewpoint Publications,1978. [2] J. Rakowski, A critical analysis of quadratic beam finite elements. International Journal for Numerical Methods in Engineering, 1991, vol. 31, pp. 949-966 [3] Z. Pawlak, J. Rakowski, Static problem of plate strip by finite strip method using difference equation method. In: Proceedings of the 15th International Conference on Computer Methods in Mechanics CMM-2003, Gliwice/Wisła, 3-6 June 2003, pp. 279-280.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
47
0RGHOLQJ7LPH'HSHQGHQW3DUWLDO(TXDWLRQVZLWK0RYLQJ%RXQGDULHVE\ WKH0RYLQJ)LQLWH(OHPHQW0HWKRG
5XL5REDOR 0DULDGR&DUPR&RLPEUDD$OtULR(5RGULJXHVE
'HSDUWDPHQWRGH0DWHPiWLFD8QLYHUVLGDGHGD%HLUD,QWHULRU 5XD0DUTXrV'¶ÈYLODH%RODPD&RYLOKm3RUWXJDO UUREDOR#PDWXELSW /65(D'(&E'(4)DFXOGDGHGH(QJHQKDULDGD8QLYHUVLGDGHGR3RUWR 5XD'U5REHUWR)ULDV3RUWR3RUWXJDO ^PFRLPEUDDURGULJ`#IHXSSW
$%675$&7
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
5HIHUHQFHV
>@ .0LOOHUDQG510LOOHU0RYLQJ)LQLWH(OHPHQWV6,$0-1XPHU$QDO >@ 0&&RLPEUD&$6HUHQRDQG$(5RGULJXHV0RYLQJ)LQLWH(OHPHQW0HWKRG$SSOLFDWLRQV WR6FLHQFHDQG(QJLQHHULQJ3UREOHPV&RPSXWHUVDQG&KHPLFDO(QJLQHHULQJ >@ 55REDOR0&&RLPEUD&$6HUHQRH$(5RGULJXHV$SOLFDomRGR0()0DSUREOHPDVFRP IURQWHLUDVPyYHLV0pWRGRV&RPSXWDFLRQDLVHP(QJHQKDULDHGV&0RWD6RDUHVHWDO
:HJUDWHIXOO\DFNQRZOHGJHWKHILQDQFLDOVXSSRUWRI)&732&,(48
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
48
Discretization of Three-Dimensional Aggregate Particles Daniel Rypl Department of Mechanics Faculty of Civil Engineering, Czech Technical University in Prague Th´akurova 7, 166 29, Prague, Czech Republic
[email protected] ABSTRACT The design of concrete with specified properties became of increasing importance with the wide use of high-performance concretes (HPCs), such as pumpable concrete or self compacting concrete (SCC). Many concrete properties, starting from the mechanical properties as the compressive strength and modulus of elasticity, over the rheological properties influencing the workability of fresh concrete, up to physical properties as diffusivity and thermal and electric conductivity, for example, can be assessed by appropriate computational model representing concrete as a multiscale random composite material with realistically described aggregates. However, incorporation of three dimensional aggregate particles into computational code requires their proper discretization. This is not straightforward due to rather difficult mathematical characterization of aggregate particles of random shape. Modern technologies as computer tomography (CT) or magnetic resonance tomography (MRT) offer a powerful nondestructive technique for digital representation of opaque solid objects. This voxel based representation can be then discretized using for example marching cubes algorithm [1]. The resolution of the resulting triangulation, however, is strongly dependent on the resolution of the digital representation which might be either too coarse (without important features being captured) or too fine (with unimportant features captured by excessive number of elements). In the present work, the digital representation is first used to derive a smooth representation of aggregate particle using the expansion into spherical harmonic functions [2]. Although this representation is not universal it is suitable for almost all aggregates used in structural concrete. The significant advantage of this approach is that resolution of the smooth representation can be flexibly controlled by the number of terms in the expansion. In the next phase, the surface of aggregate particle is subjected to discretization using the advancing front technique. Although the representation of the surface is parameterized (by two spherical angles), the actual triangulation is performed directly on the surface in the real space [3] and not in 2D parametric space with subsequent mapping to the real space. The advantage of this procedure consists in the fact that the anisotropic meshing of the parametric space as well as the demanding calculations related to the reparameterization or the inverse mapping are avoided.
References [1] W.E. Lorensen, H.E. Cline, Marching cubes: A high resolution 3D surface construction algorithm. Computer Graphics, 21, 163-169, 1987. [2] E.J. Garboczi, Three-dimensional mathematical analysis of particle shape using x-ray tomography and spherical harmonics: Application to aggregate used in concrete. Cement and Concrete Research, 32, 1621-1638, 2002. [3] D. Rypl, Sequential and parallel generation of unstructured 3D meshes. PhD. Thesis, CTU Reports, 2 (3), 1998.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
49
Bending of an Elliptical Plate on Elastic Foundation and under the Combined Action of Lateral Load and In-Plane Force Kenzo Sato Akita University Department of Engineerings and Information Sciences, Faculty of Education and Human Studies, 010-8502 Akita, Japan
[email protected] ABSTRACT The plane plates resting on elastic foundations are of practical importance in many engineering fields as seen in plate-subgrade structure, floating plate structure, composite material and so on. In some cases, the plates are subjected to large temperature differences from which considerable in-plane forces in the plates result. As structural elements in the wide fields of engineering, various types of elliptical plates may be used in order to avoid the high stress concentration and improve the usability of the instrument and the beauty of the architecture. In recent years, the author has been studied the vibration, buckling and bending problems of elliptical plates subjected to the combined action of lateral load and in-plane force[1]-[5]. In the reference [2] has been discussed also the influence of elastic foundation on the vibration and buckling of a clamped elliptical plate. From the viewpoint of the usefulness of an elliptical plate as structural element and the importance of the analytical solution in the mathematical theory of elasticity, it is the aim of this report to develop the exact theoretical analysis on the bending of an elliptical plate resting on a Winkler-type elastic foundation and subjected to the combined action of uniform lateral load and in-plane force. Here is considered the case that the plate-edge conditions are clamped and simply supported. Based on the classical small-deflection theory, the theoretical analysis is rigorously made in the elliptical coordinate system and the deflection surface due to bending of the plate is obtained in the form of an infinite Mathieu function series. The influences of elastic foundation and in-plane force on the bending of the elliptical plate are calculated by digital computer, and the new results obtained here will be presented in tables and figures.
References [1] K. Sato, Free Flexural Vibrations of a Simply Supported Elliptical Plate Subjected to an In-Plane Force. Theoretical and Applied Mechanics, 50, 165–181, 2001. [2] K. Sato, Vibration and Buckling of a Clamped Elliptical Plate on Elastic Foundation and under Uniform In-Plane Force. Theoretical and Applied Mechanics, 51, 49–62, 2002. [3] K. Sato, Bending of a Clamped Elliptical Plate under the Combined Action of Uniform Lateral Load and In-Plane Force. Theoretical and Applied Mechanics, 53, 37–47, 2004. [4] K. Sato, Bending of a Simply Supported Elliptical Plate under the Combined Action of Uniform Lateral Load and In-Plane Force. Theoretical and Applied Mechanics, 54, 31–44, 2005. [5] K. Sato, Bending of an Elastically Restrained Elliptical Plate under the Combined Action of Lateral Load and In-Plane Force. JSME International Journal, Ser.A, 49, 130–137, 2006.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
50
A modal analysis approach using an Hybrid-Mixed formulation to solve 2D elastodynamic problems M. Vicente da Silva∗ , Eduardo Pereira† ∗ Universidade
Nova de Lisboa - FCT/UNL, Civil Engineering Department Quinta da Torre, 2829-516 Monte da Caparica
[email protected]
† Instituto
Superior T´ecnico, Civil Engineering and Architecture Department Av. Rovisco Pais no 1, 1049-001 Lisboa
[email protected] ABSTRACT
The purpose of this work is to present a Hybrid-Mixed finite element formulation to solve elastodynamic plate problems in frequency domain. This Hybrid-Mixed model is derived [2] establishing, non-locally, the dynamic equilibrium, compatibility and constitutive relations based on the Galerking weighted residual method. Two different approximations fields are used in the element domain, namely the stresses and the displacements fields. A third approximation independent from the previous ones is also required for the displacement field on the static boundary of the elements. Once obtained the governing system, the stresses and the boundary displacements degrees of freedom are eliminated, thus resulting a new condensed system, were only the domain displacements degrees of freedom (qV ) intervine: (K − ω 2 M )qV = QV (1) The condensed system assume a form analogous to the one obtained with the conventional FEM[1], however with a different and richer physical meaning. In a first stage natural frequencies and shape modes are identified. Then, modal analysis technique is performed to uncouple the governing system equations, and to assess the relevance of each mode to a specific action. Less relevant modes are eliminated, thus reducing substantially the computational costs without significant lost of accuracy. The Hybrid-Mixed model is implemented using 4-node serendipian standard master elements to define the finite element shape, and non-nodal, Legendre polynomials as approximation functions. This functions are suited for this purpose because they allow to introduce in the finite element code closed form solutions to compute the coefficients of the structural matrices, avoiding time consuming numerical integration. Good results can be reach using macro finite elements since h-refinements are easy to performe simply by increasing the maximum degree of the polynomials in the approximation functions. The efficiency and performance of the presented method is validated with the aid of numerical examples. Free vibrations natural frequencies are determined and transient response in undamped and viscous damped structures are studied.
References [1] R. W. Clough and J. Penzien. Dynamics of Structures. McGraw-Hill, New York, 2nd edition, copyright 1993. [2] E. M. B. R. Pereira and J. A. T. Freitas. A mixed-hybrid finite element model based on orthogonal functions. International Journal for Numerical Methods in Engineering, 39:1295–1312, 1996.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
51
A new finite element method for Kirchhoff plates Lourenc¸o Beir˜ao da Veiga ∗, Jarkko Niiranen†, and Rolf Stenberg† ∗ Dipartimento di Matematica ”Federigo Enriques”
via Saldini 50, 20133 Milano, Italy
[email protected] †Institute of Mathematics, Helsinki University of Technology
P.O. Box 1100, 02015 TKK, Finland jarkko.niiranen@tkk.fi, rolf.stenberg@tkk.fi
ABSTRACT Based on the ideas from [1] and [2] we present a new finite element method for the Kirchhoff plate bending model [3]. The method uses C 0 basis functions for the deflection and the rotation, i.e. the same approach as used for the Reissner–Mindlin model. To account for the effective shear force at the free boundary a stabilization term is added. We prove optimal a-priori and a-posteriori error estimates. The corresponding results from benchmark problems are also reported.
References [1] P. Destuynder and T. Nevers, Une modification du mod`ele de Mindlin pour les plaques minces en flexion pr´esentant un bord libre. RAIRO Mod´el. Math. Anal. Num´er., 22, 217–242, 1988. [2] R. Stenberg, A new finite element formulation for the plate bending problem. P. G. Ciarlet, L. Trabucho, and M. Via˜no eds. Asymptotic Methods for Elastic Structures, Proceedings of the International Conference, Lisbon, October 4–8, 1993, Walter de Gruyter & Co., Berlin – NewYork, 209–221, 1995. [3] L. Beir˜ao da Veiga and J. Niiranen and R. Stenberg, A family of C 0 finite elements for Kirchhoff plates. Helsinki University of Technology, Institute of Mathematics, Research Reports, A 483, January, 2006 (http://www.math.tkk.fi/reports).
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
52
! "
!
"#$%$'$ %#$%$'$
ABSTRACT +; % % ' %' % < '
;; ; ' ;$ = ;' < %' % '%' %
? Q XZ= ' Z=$ \" < %
' ' ' ' ; % ' <
% ' Q' '< %' %$ + ' % ' ;
' ;' ;' ;
%' $ ^ '
Z < < Q _`Z|
%'$ X %' ;
~" $ +;
% ; % ' ' < '
% %
~" '
$ + '
< ' '$ ; ; ;' < %' % ' '
; ' '$ ' ' \ < %<
; % '$ ' ' %' '
%< <;$ ^ < % < ;<; '
' ;'$
References Z$
~" ; ' %' < Q _ Z|
%' %
#$%&
$ Z$ ; ' < Q %'
%$
$% $
Z$ ^ < ' < ' % '%' %
$
'% ! $
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
53
Computational Methods of Anisotropic Massif Mechanics Under Different Types of External Actions Sh. Aitalyev, R. Baimakhan, Zh. Masanov, N. Kurmanbekkyzy, G. Ylyasova Institute of Mechanics and Engineering Science Almaty, Kazakhstan, Aksay-5, house 7, ap.23
[email protected]
ABSTRACT Mechanics of mining rocks is developed adequately in Kazakhstan. It is connected with the fact that there are many deposits of solid minerals, for developing of which is necessary to build the mines and pits. For oil and gas production the wells are holed, now and then deep and super-deep. The underground railway is being built in the former capital of Kazakhstan – Almaty, which is situated in the high seismic zone. Mechanic engineers of Kazakhstan have created different calculating models of rocks massif: homogeneous isotropic and anisotropic, small-laminated and large-laminated, inhomogeneous with breaks, bloc layer, etc. In the paper the methods of calculating of the intensedeforming state of anisotropic massif round the spread underground constructions are proposed. Anisotropic is accepted as transversal anisotropic. The plane of isotropic reflects presence of stratified rocks in city. If to consider the spread underground constructions, differently oriented relative to the isotropic plane and horizontal plane, the calculating model is characterized by the eight parameters: five mechanical constants and three angles. ci, j = ci, j (E1 , E2 ,G2 ,ν 1 ,ν 2 ,ϕ ,φ , χ ) [1], [2], where
E1 , E 2 , γ 1 , γ 2 ,G - elastic constants, coefficients of Poisson, shear density modulus; these angles are the incline of isotropic plane to the horizon, deviation of the underground construction axis from the line of stretching, deviation of the isotropic plane from the horizon. Own weight of the massif, horizontal tectonic forces, seismic loadings are considered as external actions. In case of presence of all these forces, when the centers of earthquakes are far and only long-waved actions come, numerical results can be obtained easily enough by the method of conformal representations. Here are used three functions instead of the classic two analytical functions, conformable to particular space case under the conditions of generalized plain deformation. Under certain conditions the method of boundary integral equations – the method of boundary elements – is convenient. But the finite-element method is more efficient, especially when seismic loadings are given by the way of synthesized accelerograms of real earthquakes and problems of seismic waves non-stationary diffraction at the underground constructions into anisotropic massif are solved. In the paper, basically, results for rocks anisotropic massif, obtained by the finite-element method, are proposed.
References [1] Zh. Erzhanov, Sh. Aitaliev, Zh. Masanov, Seismic-stressed condition of underground structures in a stratified anisotropic massif. Nauka, Almaty, 1980. [2] R. Baimakhan, Calculation of seismic-stressed condition of underground structure in a heterogeneous stratum by finite element method. Dauir, Almaty, 2002.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
Effect of Plastic Anisotropy on the Size of Elastic-Plastic Boundary in a Rotating Disk Problem *
Nelli N. Alexandrova , Paulo M.M. Vila Real† *
Civil Engineering Department University of Aveiro, 3810-193 Aveiro, Portugal
[email protected] † Civil Engineering Department University of Aveiro, 3810-193 Aveiro, Portugal
[email protected]
ABSTRACT The problem of dependence of stress distribution and size of elastic-plastic boundary on the angular velocity, material anisotropy, boundary conditions and geometric parameters in rotating disks is of great importance due to a large number of applications. In particular, all of these parameters can have a significant effect on the development of plastic zones in such disks. The elastic stress distribution in rotating anisotropic disks with constant and variable thickness is well known. However, there are only a few studies incorporating plastic stress analysis for anisotropic materials. Considering the case of a single elastic perfectly-plastic annular rotating disk, subjected to typical stress boundary conditions, the influence of the leading design parameters - material anisotropy coefficients - on the size of elastic-plastic boundary arising due to the action of centrifugal forces is investigated. An axisymmetric problem is formulated assuming that the principal axes of anisotropy coincide with the radial and tangential directions in the plane of the disk. The Hill’s quadratic yield criterion is adopted in the plastic zone, and material properties in the elastic zone are considered to be isotropic obeying the general Hooke’s law. All stresses are assumed to be continuous across the elastic-plastic boundary. Three different characteristic values of rotational speed are chosen in numerical calculations. It is demonstrated that the size of the plastic zone is very sensitive both to the change in material anisotropy coefficients and the magnitude of angular velocity.
54
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
55
Numerical Testing on Return Map Algorithms for von-Mises Plasticity with Nonlinear Hardening based on a Generalized Midpoint Integration Scheme Edoardo Artioli1, Ferdinando Auricchio2,3, Lourenço Beirão da Veiga4 §
DISTART Department, University of Bologna Viale del Risorgimento, 2 – 40136, Bologna, Italy
[email protected] 3
2 Department of Structural Mechanics, University of Pavia Institute of Applied Mathematics and Information Technology, CNR Via Ferrata, 1 – 27100, Pavia, Italy
[email protected] 4
Department of Mathematics, University of Milan Via Saldini, 50 – 20133, Milan, Italy
[email protected]
ABSTRACT We consider an associative von-Mises elastoplastic constitutive model in the realm of small deformations [1]. The model takes into account both linear isotropic hardening and linear/nonlinear kinematic hardening. The aim of the work is to test integration algorithms based on a return mapping concept and adopting a generalized midpoint integration rule. The method under consideration was originally proposed by Ortiz and Popov [2] and further studied in the simpler case of nonhardening materials by Simo [3]. The tested method guarantees yield consistency at the end of the time step and results linearly or quadratically accurate depending on the choice of the integration parameter. The numerical algorithm adopts a return map update based on a projection along the midpoint normal-to-yield-surface direction onto the endpoint limit surface. A testing on the method accuracy and precision is carried out by comparison with a new exponentialbased integration algorithm [4]. The comparison is carried out solving zero-dimenisonal mixed prescribed stress-strain loading histories. Accuracy and precision are determined by plotting the instantaneous error graphs on stress and strain as well as iso-error maps on stress.
References [1] J. Lubliner, Platicity Theory. Macmillan Publishing Company, 1990. [2] M. Ortiz, W. Popov, Accuracy and stability of integration algorithms for elastoplastic constitutive relations. International Journal for Numerical Methods in Engineering, 21, 15611577, 1985. [3] J.C. Simo, Numerical analysis and simulation of plasticity. in Handbook of numerical Analysis, P.G. Ciarlet and J.L. Liond Eds., Elsevier, 1998. [4] A. Artioli, F. Auricchio, L. Beirão da Veiga, Second-order accurate integration algorithms for von-Mises plasticity with a nonlinear kinematic hardening mechanism. Computer Methods in Applied Mechanics and Engineering, submitted, 2006.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
56
A Model for the Analysis of Plates on a Layered Elastic Medium Mehmet Zülfü Aúık* *
Middle East Technical University Dept. of Engineering Sciences
[email protected]
ABSTRACT In the present study, a gross model is developed to represent the behavior of a plate on a layered medium. The model assumes that the displacements take place only in vertical direction, and the plate is only subjected to the vertical forces. Total depth of foundation is finite. The model developed in this study predicts the static response of a plate on a layered medium. The present model is a simple and a semi-analytical one. The method is based on the minimum potential energy and variational principles. Shear modulus of the foundation is assumed to be different and constant at each layer. The coupled equations derived for each layer by using minimum potential energy and variational principles, are solved by employing finite difference method and iterative procedure. Results are compared with the finite element model for the verification of the model. The computer code developed for the numerical model can be run even on small computers.
References [1] [2] [3] [4] [5] [6]
[7]
[8] [9]
T. Nogami, Two-parameter Layer Model for Analysis of Slab on Elastic Foundation , J. Engrg. Mech. ASCE, 113,1279-1291, 1987. R. Jones and J. Xenophontos, The Vlasov Foundation Model , Int. J. Mech. Sci., 19, 317-323, 1977. C. V. G. Vallabhan and Y. C. Das, Modified Vlasov Model for Beams on Elastic Foundations , J. Geotech. Engng., ASCE, 117:6, 956-966,1991. C. V. G. Vallabhan and Y. C. Das, The Analysis of Circular Tank Foundations , J. Engng. Mech., ASCE, 117:4, 789-797, 1991. C. V. G. Vallabhan and Y. C. Das, A Refined Model for Beams on Elastic Foundations , Int. J. Solids Structures, ASCE, 27:5, 629-637, 1991. M. Z. Asik, C. V. G. Vallabhan and Y. C. Das, Vertical Vibration Analysis of Rigid Circular Footings on a Soil Layer with a Rigid Base , Developments in Theoretical and Applied Mechanics, SECTAM,Volume XVIII, Alabama, 1996. M. Z. Asik, 3-D Model for the Analysis of the Rectangular Machine Foundations on a Soil Layer , 6th International Symposium on Numerical Models in Geomechanics, NUMOG VI, Montreal, Canada, 1997. M. Z. Asik, Dynamic Response Analysis of the Machine Foundations on a Nonhomogeneous Soil Layer , Computers and Geotechnics, 24:2, 141-153, 1999. M. Z. Asik, Analysis of Strip Footings on a Layered Medium , International Conference on Enhancement and Promotion of Computational Methods in Engineering Science, 2-5 Agust, 1999, Macao, China, 1999.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
57
Modeling of solid state transformations using a phase field model with transformation plasticity S. Benke ACCESS e. V. Materials and Processes, RWTH Aachen, D-52072 Aachen, Germany Address
[email protected]
ABSTRACT The evolution of the morphology of a second phase during solid state transformations is influenced by various factors like the degree of the misfit strain, distribution of the precipitates, anisotropy and inhomogeneity of the stiffness, interfacial energy, diffusion of solute atoms and others. From experimental observations it is well known that the evolution of a solid-state phase transformation in a stressed metal induces plastic deformation, even for very small applied stresses. Two transformation mechanisms can be distinguished: the transformation dilatation leading to a volume change (Greenwood-Johnson mechanism) and the martensitic transformation which results additional in shape changes (Magee effect). In the present contribution we focus our attention to volumetric phase transformations in low carbon steels caused by a diffusion controlled growth of ferrite in an austenitic matrix. The microstructural evolution is simulated by the use of a multi-phase field model which is based on the diffuse interface theory [1]. The model combines the diffusion of the species which defines the time scale, the curvature of the interfaces which defines the length scale and phase diagram information as well as the mechanical strain energy which both represent the energy scale. For the solution a combination of finite difference and finite element methods is used. The evolution of the microstructure is calculated with the software MICRESS [2] which solves the system of equations consisting of phase field equations and the diffusion equation using a control volume approach. MICRESS is coupled to a nonlinear finite element code which solves the mechanical subproblem and passes back the mechanical part of the driving force of the phase transformation in a staggered way within the solution procedure. From a mechanical point of view both phases are assumed to behave elasto-visco-plastically and the material properties in turn vary with the phase field parameters which describe the evolution of the microstructure. Using this model the influence of the strain energy on the γ − α transformation in a low alloyed carbon steel is studied. During the phase transformation the evolution of the inelastic strain due to creep and relaxation effects is tracked and the effect of different external loadings on the developed morphology is investigated.
References [1] I. Steinbach, F. Pezzolla, B. Nestler, M. Seeelberg, R. Prieler, G. J. Schmitz, J. L. L. Rezende, A phase field concept for multiphase systems. Physica D 94, 135–147, 1996. [2] www.micress.de
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
58
Computer modeling of three-dimensional wave movements in anisotropic elastic environments S. Bosiakov, M. Zhuravkov Belarusian State University
[email protected] [email protected]
ABSTRACT The theory of elastic waves in anisotropic bodies concerns to well enough investigated section of mechanics of continuous environments and the basic results in this direction belong to F. I. Fedorov, M. J. Musgrave, R. G. Payton, E. Dieulesaint, D. Royer [1, 2, 3], etc. However, three-dimensional representations of wave movements (a surface of reverse velocities, wave surfaces) are absent in full, that it is possible to explain complexity and bulkiness of the corresponding characteristic equations, and also absence of their exact analytical decision (exception transversal-isotropic environments make). Researches of features of propagation of flat elastic waves and classification of anisotropic environments are lead for special directions and crystallographic planes of an anisotropic body, which not always yields true and consistent results. The offered approach to visualization and the quantitative description of three-dimensional wave movements bases on sharing of system of computer mathematics Mathematica in aggregate with methods of characteristics of the theory of the differential equations with partial derivatives of hyperbolic type. Thus the basic stages of modeling of wave processes are the finding of the characteristic equation, its analytical decision, definition of velocities of propagation of elastic waves and coordinates of points of environment which energy of wave indignation has reached. The specified stages are put in a basis of the package of expansion of system Mathematica developed by authors which functionalities allow to execute construction of surfaces of velocities, reverse velocities and surfaces of ray velocities (three-dimensional wave fronts), and also to construct sections of these surfaces any plane which is passing through the beginning of coordinates for anisotropic environments of any class of symmetry. Surfaces of reverse velocities and wave surfaces enable to carry out the strict classifications of anisotropic environments basing the simultaneous account of features two quasitransversal waves. The obtained results also can be used both for correct statement of experiments, and for correct interpretation of experimental data as allow to generate evident representations about features of propagation of waves in anisotropic environments.
References [1] ɗ. Ⱦɶɟɥɟɫɚɧ, Ⱦ. Ɋɭɚɣɟ, ɍɩɪɭɝɢɟ ɜɨɥɧɵ ɜ ɬɜɟɪɞɵɯ ɬɟɥɚɯ. ɉɪɢɦɟɧɟɧɢɟ ɞɥɹ ɨɛɪɚɛɨɬɤɢ ɫɢɝɧɚɥɨɜ. Ɇɨɫɤɜɚ, ɇɚɭɤɚ, 1982. [2] Ɏ. ɂ. Ɏɟɞɨɪɨɜ, Ɍɟɨɪɢɹ ɭɩɪɭɝɢɯ ɜɨɥɧ ɜ ɤɪɢɫɬɚɥɥɚɯ. Ɇɨɫɤɜɚ, Ɇɢɪ, 1965. [3] M. J. Musgrave, R. G. Payton, Criteria for elastic waves in anisotropic media. Jornal of Elasticity, 14, 269-285, 1984.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
59
Visco-elastic regularization and strain softening Rui S. Cardoso *,1, Vitor D. Silva †, Humberto Varum *,2 * University of Aveiro Department of Civil Engineering Campus Universitário de Santiago, P-3810-193 Aveiro, Portugal 1
[email protected]
2
[email protected]
† University of Coimbra Department of Civil Engineering Polo II da universidade-Pinhal de Marrocos, P-3030-290 Coimbra, Portugal
[email protected] ABSTRACT In this paper it is intended to verify the capacity of regularization of the numerical solution of an elasto-plastic problem with linear strain softening. The finite element method with a displacement approach is used. Drucker-Prager yield criteria is considered. The radial return method is used for the integration of the elasto-plastic constitutive relations. An elasto-visco-plastic scheme is used to regularize the numerical solution. Two constitutive laws have been developed and implemented in a FE-program, the first represent the radial return method applied to Drucker-Prager yield criteria and the second is a time integration procedure for the Maxwell visco-elastic model. Attention is paid to finite deformations. An associative plastic flow is considered in the Drucker-Prager elasto-plastic model. The algorithms are tested in two problems with softening. Figures showing the capability of the algorithms to regularize the solution are presented.
References [1] V. D Silva, A simple model for viscous regularization of elasto-plastic constitutive laws with softening. Communications in Numerical Methods in Engineering, John Wiley & Sons, Ltd., Vol. 20, pp. 547-568, 2004. [2] R. Cardoso, Regularização visco-elástica de problemas elasto-plásticos com amaciamento, MS.c Thesis, University of Coimbra, 2001 (in Portuguese). [3] H. Varum, R. Cardoso, A geometrical non-linear model for cable systems analysis, Second International Conference on Textile Composites and Inflatable Structures, Eds. E. Onãte and B. Kröplin, Stuttgart 2-5 October 2005, pp. 234-242. [4] V. D. Silva, Mechanics and Strength of Materials, ISBN 3-540-25131-6, 529 p., 402 illus., Springer, 2006. [5] J. Argyris, I. St. Doltsinis, V. D. Silva, Constitutive modelling and computation of non-linear viscoelastic solids – Part I: Rheological Models and Numerical Integration Techniques. Computer Methods in Applied Mechanics and Engineering, Vol. 88 No.2, pp. 135-163, 1991.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
60
Numerical simulations of the Rayleigh-Taylor instability in accelerated solids Juan J. López Cela1*, Antonio R. Piriz1 and María C. Serna1 1 Escuela Técnica Superior de Ingenieros Industriales Universidad de Castilla La Mancha 13071 Ciudad Real, Spain
[email protected]
ABSTRACT The classical Rayleigh-Taylor (RT) instability is developed in the interface that separates a heavy fluid from a lighter one in the presence of a gravitational field. If the interface is not perfectly planar, its small perturbations will grow without bound. When a solid is submitted to a very high acceleration, for example by the application of an external pressure on one of its faces, this interface is also RT unstable. This kind of situations are found in several technological applications like explosive forming process, laser implosion of fusion targets, electromagnetic implosion of metal liners or experiments to achieve hydrogen metallization [1]. If the RT instability appears the experiment could fail. So it is important to study which are the mechanisms that produce stabilizing effects to alleviate the growth of the instability. When we are dealing with fluids the stabilizing mechanisms are, for example, gradient effects, viscosity and superficial tension. Dealing with solids, their intrinsic properties can produce such a stabilizing effect. In a very simple interpretation, the elastic forces that the solid develop can compensate the buoyancy force that leads the instability, but when the material plastifies it can again be unstable. Analytical solutions are only available for elastic solids. The exact analytical solution describing the entire process exists only for solid-vacuum interfaces [2]. For solid/solid and viscous fluid/solid interfaces there is an exact analytical model that describes only the asymptotic phase [3] and an approximate analytical model that we have presented elsewhere [4] that describes not only the asymptotic behaviour but also the initial transient phase. The initial transient phase is of great importance because the instability could enter in the non-linear regime or in the plastic flow before the asymptotic regime is reached. In this work we present some numerical simulations based on the Finite Element Method for a very thick solid layer. In particular we have verified that the stability criteria defined by previous models are consistent with the simulations and also we have studied the influence of the elastic material parameters.
References [1] N. A. Tahir et al, Metallization of hydrogen using heavy-ion-beam implosion of multilayered cylindrical targets, Physical Review E, 63, pp. 016402-016410, 2001. [2] B.J. Plohr and D.H. Sharp, Instability of accelerated elastic metal plates, Z. Angew. Math. Phys. 49, 786-804, 1998. [3] G. Terrones, Fastest growing linear Rayleigh-Taylor modes at solid/fluid and solid/solid interfaces, Physical Review E 71, pp. 036306-036316, 2005. [4] A. R. Piriz, J. J. López Cela, O.D. Cortázar, N.A. Tahir and D.H.H. Hoffmann, Rayleigh-Taylor instability in elastic solids, Physical Review E 72, pp. 056313, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
61
A Phenomenological Model to Simulate Mechanical Tests on Ultrafinegrained Aluminum Produced by ECAE B. Diouf*, F. El Houdaigui*, S. Poortmans†, B. Verlinden†, A. M. Habraken*. *
Department of Mechanics of Materials and Structures University of Liège, chemin des Chevreuils 1, 4000 Liège, Belgium {bdiouf, felhoudaigui, Anne.Habraken}@ulg.ac.be †
Department of Materials Engineering Katholieke Universiteit Leuven, Kasteelpark Arenberg 44, 3001 Leuven, Belgium {Stijn.Poortmans, Bert.Verlinden}@mtm.kuleuven.be
ABSTRACT Results of FEM simulations predicting the mechanical behaviour at room temperature of test specimens of ultrafine-grained aluminum produced by ECAE following route BC [1] for 8 passes are presented. The constitutive law is either based on a Hill model or on the Minty micro-macro [2] model and coupled with an isotropic hardening law and/or kinematic hardening law. The yield locus shape, its size and its position during tension, compression and torsion tests have been studied. Initial texture measurements allow identification of a constitutive law based on a set of representative crystals and crystal plasticity approach using a Full-Constraint Taylor model. Finite element simulations using the previous constitutive laws are compared with experimental investigations. The results show that applying an initial back stress identified by tensile and compression tests to the yield locus predicts the initial flow stress in torsion test. The Minty micromacro model coupled with a Voce type hardening model gives a good agreement with experimental results for the prediction of the shape at different stages of deformation of a compressed test specimen. The simulation of tensile tests underline the need of inverse modelling as, due to the test specimen shape, the test is far from being homogeneous. The link between test specimen length and the necking appearance is studied.
References [1] V.M. Segal, Materials processing by simple shear. Materials Science and Engineering: A, 197, 157-164, 1995. [2] A.M. Habraken, L. Duchêne, Anisotropic elasto-plastic finite element analysis using stress-strain interpolation method based on a polycrystalline model. International Journal of Plasticity, 20(89), 1525-1560, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
62
The peridynamic equation of motion in non-local elasticity theory Etienne Emmrich∗ , Olaf Weckner† ∗ Technische
Universit¨at Berlin, Institut f¨ur Mathematik Straße des 17. Juni 136, 10623 Berlin, Germany
[email protected]
† Massachusetts
Institute of Technology, Department of Mechanical Engineering Cambridge, MA 02139, USA
[email protected]
ABSTRACT During the last few years, non-local theories in solid mechanics that account for effects of long-range interactions have become topical again. One of these theories is the so-called peridynamic modelling, introduced by Silling [1]. The governing equation of motion is the partial integro-differential equation f (x, x ˆ, u(x, t), u(ˆ x , t), t) dˆ x + b(x, t) , x ∈ V , t > 0 , ρ(x)∂t2 u(x, t) = H(x)
for the displacement field u = u(x, t) of a body that occupies the reference volume V, supplemented by initial conditions for u(·, 0) and ∂t u(·, 0). Here, ρ denotes the mass density, f the so-called pairwise force field that describes the interaction of material particles, and b collects outer forces. Moreover, H(x) = {ˆ x ∈ V : ˆ x − x ≤ δ} is the so-called peridynamic horizon for prescribed δ > 0. An essential feature is that f is independent of any spatial derivative. It is, therefore, a promising approach for the simulation of problems in which discontinuities emerge such as fracture or cracking. The peridynamic modelling has recently been successfully applied in numerical simulations of problems in solid mechanics such as the fracture of a plate with notches, the undirected growth of cracks, the wrinkling and tearing of membranes, the deformation of composite materials etc. In this talk, we give an overview of the peridynamic modelling as well as the numerical and theoretical results obtained so far. Concentrating on the description of a linear microelastic material, we present new results concerning the well-posedness of the problem. We then suggest a quadrature formula methods for the spatial approximation of the governing equation and show some numerical simulations. Moreover, the question of energy conservation and the comparison of elastic energy in both the peridynamic and the classical theory are discussed.
References [1] S. Silling, Reformulation of elasticity theory for discontinuities and long-range forces. J. Mech. Phys. Solids, 48, 175–209, 2000.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
63
Numerical Solution of Partially Plastic Curved Beam Problem Ahmet N. Eraslan, Eray Arslan Department of Engineering Sciences Middle East Technical University, Ankara 06531, Turkey {aeraslan, erarslan}@metu.edu.tr
ABSTRACT Numerical solutions are obtained for elastic and elastic-plastic bending of a curved beam via couples at its end sections, under plane stress presupposition. The model proposed is based on the von Mises' yield criterion, Henky's deformation theory, and nonlinear strain hardening material behavior. Using formal nondimensional variables, and an appropriate stress function, a single second order nonlinear differential equation describing the deformation behavior of the curved beam is obtained. A shooting technique using Newton iterations with numerically approximated tangents is used for the numerical integration of the governing equation. The computational model is verified both in elastic and partially plastic cases making use of published analytical and numerical FEM solutions. 1.2
stresses and displacement
0.8
I
I
VT
0.4
Vr 0.0
VT
u u10
-0.4
-0.8
rEP
1.081
rNA 1.239
rEP
1.434
-1.2 1.0
1.1
1.2
1.3
1.4
1.5
radial coordinate (r/a)
Figure 1: Stresses and displacement in a partially plastic curved beam.
The distributions of stress and displacement in a partially plastic nonlinearly hardening curved beam at T 0q plane is displayed in Fig. 1. Inner radius to outer radius ratio, a / b , has been taken as 1.5 . The stress variable I in this figure is computed from von Mises' yield equation so that I t 1 in a plastically deformed region. The two vertical lines labeled as rEP , which correspond to I
1,
indicate elastic-plastic borders. Other vertical line rNA points the neutral axis at which V T rNA 0 . The curved beam is composed of an inner plastic region in 1 d r d 1.081 , an elastic region in 1.081 d r d 1.434 , and an outer plastic region in 1.434 d r d 1.5 .
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
64
A Proposal of Strain-Gage Rosette for Measurement Residual Stress Around a Circular Hole in a Plate With Circular Hole José Luiz Fernandes*, Antonio Carlos Marques Alvim†, Renato Seixas da Rocha† *
Federal Center of Technological Education – Mechanical Engineering Department Av. Maracanã, 229, BlocoE, Sala505.7
[email protected] †
Nuclear Engineering Programme – COPPE / UFRJ – Brazil Av. Maracanã, 229, BlocoE, Sala505.7
[email protected] †
R&D Center of Petrobras – CENPES – Brazil
Cidade Universitária – Avenida Jequitibá – Quadra 7 – Ilha do Fundão ZIP code 21949-900 – Rio de Janeiro – RJ – Brasil
[email protected]
ABSTRACT Hole-drilling strain-gage rosette method is an experimental technique used to measure residual stresses near the surface of a mechanical component. Various types of rosettes are available with different geometric configurations and dimensions. The strain field high gradients observed near the hole, where the strain-gage rosette is bonded, makes the problem of choosing the optimal rosette position a critical one. In this work a methodology of residual stress measurement for the technique Hole-Drilling was developed to simulate the effect of a through circular hole in a thin plate submitted under nominal uniaxial and biaxial loads up to the yield strength (Se). In the biaxial case was considered relations between the nominal components load of Vnx/Vny = 0,25, 0,50, 0,75 and 1,00. It was simulated by finite elements the measurement residual stress methodology named “HoleDrilling" in plate submitted nominal biaxial big loading until the yielding stress for the API 5L X60. In this study was projected and a strain gage rosette containing 5 strain gages positioned 0, 90, 150, 225 and 300 degrees. The relative error was evaluated between the numeric solution and the theoretical solution proposed by ASTM E837 (elastic) and by Savin (elastoplastic). It was verified that the relative errors for the main strain H1 and H2, obtained by the strain gages redundant to decrease. It is worth to emphasize that the strain gages rosette proposed with five strain-gages didn't eliminate the problem of the eccentricity, but it quantified with larger precision this effect.
References [1] Beghini, M.; Bertini, L.; Raffaelli, P. “Numerical analysis of plasticity effects in the hole-drilling residual stress measurement”, Journal of Testing and Evaluation, JTEVA, Vol. 22, No 6, November, pp. 522 529, 1994. [2] Fernandes, J.L., A Methodology for the Analysis and Modeling of Residual Stresses, (in Portuguese), Doctor Degree Thesis, Department of Mechanical Engineering, PUC/RJ, 340p.,2002. [3] Fernandes, J.L., Castro, J.T.P., 2003, “Analysis Elastoplastic of Stress around a Circular Hole in a Plate Submitted Biaxial and Uniaxial Loading”, 58nd International Congress of Brazilian Metals Association, Rio de Janeiro, 2003. [4] Kabiri, M., 1984, “Non-uniform residual stress measurement by hole-drilling method”, Experimental Mechanics, pp. 328 – 336, 1984.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
65
3UHGLFWLRQRIG\QDPLFVWLIIQHVVRIILOOHGUXEEHUPRXQWV
-*yPH]-05R\R)-0DUWtQH](/LDUWH0$-LPpQH] ,QVWLWXWR7HFQROyJLFRGH$UDJyQ F0DUtDGHOXQD=DUDJR]D6SDLQ MJRPH]#LWDHV
$%675$&7
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¶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µWLPHWRPDUNHW¶DQGRI WKHQXPEHURIWHVWVRQSURWRW\SHVGXULQJWKHGHYHORSPHQWSKDVHZKLOHLQFUHDVLQJWKHSHUIRUPDQFHRI UXEEHUPRXQWV
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
66
Size effects in finite deformation micropolar plasticity P. Grammenoudis∗ , Ch. Tsakmakis∗ ∗ Darmstadt
University of Technology Department of Mechanics AG 1 Continuum Mechanics Hochschulstraße 1 D-64289 Darmstadt Germany
[email protected] [email protected] ABSTRACT Micropolar theories offer a possibility to model size effects in the constitutive behavior of materials. Typical feature of such models is that they deal with a microrotation, which is supposed to represent an independent state variable, and its space gradient. As a consequence, the stress tensor is no longer symmetric and couple stresses enter the theory. Accordingly, a micropolar plasticity law exhibiting kinematic hardening effects should account for both, a back-stress tensor and a back-couple stress tensor. This has been considered in the micropolar plasticity model developed by Grammenoudis and Tsakmakis [1], [2]. To be more specific, we assume the multiplicative decomposition to apply for both the deformation gradient tensor of the macroscopic continuum and the micropolar rotation tensor of the assigned microstructure. From these, we obtain additive decompositions for the strain and curvature tensors as well as their associated rates. A yield function is assumed which reflects isotropic and kinematic hardening effects. The stress tensor and the back-stress tensor in the yield function are supposed to obey the structure of the so-called Mandel stress tensor within the framework of classical (non-polar) plasticity. All constitutive equations are defined in such a manner that the second law of thermodynamics is fullfilled in every admissible process. The capabilities of the constitutive theory are demonstrated by means of finite element calculations. To this end, the micropolar plasticity model is implemented into finite element code ABAQUS. Details of the implementation are given in Grammenoudis and Tsakmakis [2]. Here, a discussion of the influence of hardening on size effects is given, with reference to torsion deformation (see Grammenoudis and Tsakmakis [3]).
References [1] P. Grammenoudis and Ch. Tsakmakis, Hardening rules for finite deformation micropolar plasticity: Restrictions imposed by the second law of thermodynamics and the postulate of Il’iushin. Continuum Mechanics and Thermodynamics, 13, 325–363, 2001. [2] P. Grammenoudis and Ch. Tsakmakis, Finite element implementation of large deformation micropolar plasticity exhibiting isotropic and kinematic hardening effects. International Journal for Numerical Methods in Engineering, 62, 1691–1720, 2005. [3] P. Grammenoudis and Ch. Tsakmakis, Predictions of microtorsional experiments by micropolar plasticity. Proceedings of the Royal Society, 461, 189–205, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
67
An Application of a Boundary Perturbation Method to Some Problems of Elasticity M. Grekov St. Petersburg State University Universitetski Pr., 35, St. Petersburg, 198504, Russia
[email protected]
ABSTRACT There are a lot of problems of great importance in continuum mechanics, which can be solved by means of the perturbation method. In many cases, this method relates to a perturbation of a reference boundary for which a similar boundary problem has a relatively simple solution or can be easy solved in a closed form. The weakness of all cited works is that they are confined to constructing the first order perturbation solutions and the perturbation technique is carried out in different manners even for the 2-D problems. At the same time, using Kolosov's complex potentials, a unified perturbation method for the 2-D problem of elasticity has been developed. Based on this method and algorithm constructed, one can easy compute any-order accurate solution of a wide range of boundary problems. The aim of the present paper is to illustrate the general approach to constructing an algorithm of the unified boundary perturbation method. A brief review of the works devoted to the application of the perturbation technique to the crack and interface problems is presented. A unified boundary perturbation method based on Goursat-Kolosov's complex potentials and Muskhelishvili's complex variable representations is expounded for the cases of a slightly curved interface and an interfacial crack slightly deviating from a straight one. An algorithm of deriving the complex potentials of anyorder accurate perturbation solution in a closed form has been developed for the problems under consideration. Explicit results are given for the first-order solutions when local deviations of the boundary from the straight one are described by power functions. Characteristics of a stress field are analyzed for locally curved interfaces and curvilinear interfacial cracks. These studies have been partly described in works [1–3].
References [1] M.A. Grekov. A perturbation method in a problem on deformation of composite with slightly curved interface. Vestnik of St. Petersburg University, Ser. 1, 1, 81-88, 2004 (in Russian). [2] M.A. Grekov, S.N. Makarov. Stress concentration at a slightly curved section of a surface of an elastic body. Izvestiya RAN. Mekhanika tverdogo tela, 6, 53-61, 2004 (in Russian, translated in Mechanics of Solids). [3] M.A. Grekov, J.V. Malkova. Application of the perturbation method to the problem on a curvilinear interfacial crack. Int. Conference on Stability and Control Processes, St. Petersburg, Russia, 3, 1655-1656, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
68
Spatial Stabilization of Semidiscrete Elastodynamics Eran Grosu, Isaac Harari ∗ Department of Solid Mechanics, Materials, and Systems, Tel Aviv University 69978 Ramat Aviv, Israel ∗
[email protected] ABSTRACT Solutions of direct time integration schemes that converge in time to conventional semidiscrete formulations may be polluted at small time steps by noncausal oscillations. These pathologies are the deleterious effects of higher modes of spatially discrete formulations, which are approximated poorly. Algorithmic damping reduces the effect of these higher modes, but they are inevitably admitted into the computation as the time step is reduced on a fixed mesh, with convergence to the solution of the semidiscrete formulation. This degradation is not an artifact of the time-marching scheme, but rather a property of the solution of the semidiscrete formulation itself. The Rothe method (or horizontal method of lines) of first discretizing in time and then in space on each discrete time level is employed in order to characterize the onset of such pathologies and eliminate them. Standard finite elements are optimal in the energy norm for elastostatics, and thus need not be stabilized. In the transient case, the Rothe method reveals that the time-discrete equation that is solved at each time level of standard implicit schemes is, in fact, a Galerkin approximation of a steady elasticity equation with an additional reaction term. An analogy to such singularly perturbed elliptic problems provides a threshold for the onset of small time step oscillations. Numerical computations at smaller time steps might violate the principle of causality. A simple procedure of spatial stabilization removes this pathology from implicit time-integration schemes, without effecting unconditional temporal stability, leading to implicit time-integration that is free of noncausal oscillations. Computation of discontinuous phenomena with the trapezoidal rule (the implicit, unconditionally stable, second-order accurate algorithm of the Newmark family of methods) is accompanied by spurious oscillations, due to its lack of algorithmic damping. At time steps above the threshold for spatial stability these oscillations follow the wave front, but below this critical time step the oscillations precede the wave front, violating the principle of causality. In the spatially stabilized version of the trapezoidal rule the oscillations persist, but always behind the wave front, regardless of the time step. The HHT-α [1] and Generalized-α [2] algorithms are implicit, unconditionally stable, second-order accurate schemes that possess adjustable algorithmic damping, significantly reducing the spurious oscillations observed in the trapezoidal rule. Nonetheless, below the critical time step, spurious oscillations precede the wave front. Spatial stabilization of these algorithms eliminates the spurious precursors to the wave front at all time steps.
References [1] H. M. Hilber, T. J. R. Hughes, and R. L. Taylor, Improved numerical dissipation for time integration algorithms in structural dynamics. Earthquake Eng. Struct. Dyn., 5, 282–292, 1977. [2] J. Chung and G. M. Hulbert, A time integration algorithm for structural dynamics with improved numerical dissipation: The generalized-α method. Trans. ASME J. Appl. Mech., 60, 371–375, 1993.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
69
Modeling the Grain Size Effect using Gradient Hardening and Damage in Crystal (Visco) Plasticity Mikkel Grymer, Magnus Ekh, Kenneth Runesson, Thomas Svedberg Chalmers University of Technology, Dept. of Applied Mechanics 412 96 G¨oteborg, Sweden
[email protected]
ABSTRACT The macroscopic behavior of a polycrystalline material (metal) depends on the characteristics of the grain structure. Among the important properties are the size and morphology of the grains, volume fraction of different phases, and the subgrain material modeling. In this contribution we put emphasis on the modeling and numerical simulation of the grain size dependence on the macroscopic response (in terms of onset of yielding, hardening/softening characteristics, etc.). Within the framework of continuum thermodynamics and finite strains, we formulate a subgrain material model that comprises crystal (visco)plasticity, crystal damage and gradient hardening. The crystal damage is based on the concept of a fictitious (undamaged) configuration, and it is assumed to be driven by inelastic slip in each slip system. Furthermore, the gradient hardening gives a contribution from each slip system which is added to the well established local hardening. The grain interaction in a Representative Volume Element is resolved using finite elements. In order to solve the arising coupled field equations (for the displacements and the gradient hardening in the slip systems) a so-called dual mixed FE algorithm is adopted. Linear displacements and gradients are assumed in a basic set-up. As an alternative, quadratic displacements are introduced, while the linear gradient approximation is retained. Dirichlet boundary conditions on the RVE (corresponding to a given macro-scale deformation gradient) are adopted, and various prolongation conditions inside the RVE are investigated: The classical Taylor assumption, Generalized Taylor assumption (to grain boundaries only) and a fully unconstrained local displacement field. In particular, the two first approaches may be used to provide a good start solution for the fully unconstrained (most general) approach. All computations are restricted to 2D.
References [1] T. Svedberg and K. Runesson, Algorithm for gradient-regularized plasticity coupled to damage based on a dual mixed FE-formulation. Computer Methods in Applied Mechanics and Engineering, 161(1-2), 49–65, 1998. [2] M. Ekh R. Lillbacka and K. Runesson, A model framework for anisotropic damage coupled to crystal (visco)plasticity. International Journal of Plasticity, 20(12), 2143–2159, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
70
Stress-Focusing Effect Following Dynamically Transforming Strains in a Spherical Zirconia Inclusion Toshiaki Hata Faculty of Education, Shizuoka University 836 Oya Aoiku, Shizuoka City, 422-8529, Japan
[email protected] ABSTRACT Some composite materials, such as Zirconia toughened ceramics, are remarkable material, which has a high strength, a high elastic modulus, and an improved toughness, etc. Most of the good qualities are common in many ceramic composite materials. These good qualities are made possible through the phase transformation of composite particles. The mechanism in the toughening of ceramics is the stressinduced phase transformation of a Zirconia particle as shown in the work by Garvie et al. [1], which is accompanied by a volumetric expansion. Due to this expansion, the composite material consisting of Zirconia particles within a brittle matrix becomes more resistant to the thermal fracture. While in the dynamic state the mechanism in the toughening of ceramics is not clarified. The elastodynamic response of the transformation-toughened ceramics under an instantaneous phase transformation has been investigated in Ref.[2]. The transformation toughening utilizes the stress-induced phase transformation of particles, which is accompanied by a dynamic volumetric expansion. In this paper a phenomenological model is proposed to describe the situation, which involves a dynamic phase transformation in a spherical particle of Zirconia embedded in the infinite elastic matrix. When an infinite elastic medium with a spherical inclusion of Zirconia is suddenly subjected to an instantaneous transversely anisotropic phase transformation, stress waves occur at the surface of spherical inclusion the moment instantaneous transformation strains are applied. The stress wave in an inclusion proceeds radially inward to the center of the inclusion. The wave may accumulate at the center and show the stress-focusing effects, even though the initial stress should be relatively small. Stress waves, which develop following rapid transformation strains, display a stress-focusing effect as they proceed radially towards the center in this geometry. After the numerical calculations we conclude that the stress-focusing effects in a spherical inclusion play an important role in the fracture of matrix. In the steady state the fracture in the matrix with a spherical inclusion occurs at the interface of an inclusion, whereas in the dynamic case the fracture in the matrix with a spherical inclusion occurs at the center of an inclusion because of the stress-focusing effects. Therefore it should be noted that the stress-induced mechanism of phase transformation in the toughening of the Aluminum Oxide ceramics with a Zirconia inclusion in the steady state does not hold in the dynamic state.
References [1] R.C. Garvie, R.H. Hannink, and R.T. Pascoe, Ceramic Steel, Nature, 258, 703–704, 1975. [2] T.Hata, Stress-Focusing Effect in a Spherical Inclusion Embedded in an Infinite Medium Caused by Instantaneous Phase Transformation, Dynamics of Advanced Materials and Smart Structures, Kluwer Academic, 95–104, 2003.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
71
Controllability Method for the Solution of Linear Elastic Wave Equation Erkki Heikkola1 , Sanna M¨onk¨ol¨a∗,2 , Anssi Pennanen2 , Tuomo Rossi2 1 Numerola
Oy, P.O. Box 126, FI-40101 Jyv¨askyl¨a, Finland of Mathematical Information Technology, P.O. Box 35 (Agora) FI-40014 University of Jyv¨askyl¨a, Jyv¨askyl¨a, Finland ∗
[email protected].fi
2 Department
ABSTRACT We consider the use of controllability techniques for the numerical solution of time-harmonic elastic wave equations. Instead of solving directly the time-harmonic equation, we return to the corresponding time-dependent equation and look for time-periodic solution. The basic approach is to time-integrate the wave equation from initial conditions until the time-periodic solution is reached. Unfortunately, the convergence of such an approach is usually slow. We accelerate the convergence with a control technique by representing the original time-harmonic equation as an exact controllability problem for the time-dependent wave equation. This involves finding such initial conditions that after one timeperiod the solution and its time derivative would coincide with the initial conditions. Spatial discretization is done with spectral element method. It allows convenient treatment of complex geometries and varying material properties. The basis functions are higher order Lagrange interpolation polynomials, and the nodes of these functions are placed at Gauss-Lobatto collocation points. The integrals in the weak form of the equation are evaluated with the corresponding Gauss-Lobatto quadrature formulas. As a consequence of the choice, spectral element discretization leads to diagonal mass matrices which significantly improves the computational efficiency of the explicit time-integration used. Moreover, when using higher order elements, same accuracy is reached with less degrees of freedom than when using lower order finite elements. After discretization, exact controllability problem is reformulated as a least-squares optimization problem, which is solved with a preconditioned conjugate gradient algorithm. Each conjugate gradient iteration requires computation of the gradient of the least-squares functional, which involves the solution of the state equation and the corresponding adjoint equation, solution of a linear system with the preconditioner, and some matrix-vector operations. Computation of the gradient of the functional is an essential point of the method, and we have done it with the adjoint state technique directly for the discretized problem. Algebraic multigrid method is used for preconditioning the conjugate gradient algorithm.
References [1] M. O. Bristeau, R. Glowinski, and J. P´eriaux. Controllability methods for the computation of timeperiodic solutions; application to scattering. Journal of Computational Physics, 147(2), 265-292, 1998. [2] G. C. Cohen, Higher-Order Numerical Methods for Transient Wave Equations, Springer, 2002. [3] F. Kickinger, Algebraic multi-grid for discrete elliptic second-order problems. Multigrid methods V (Stuttgart, 1996), 157–172, Springer, 1998. [4] J.J. Heys, T.A. Manteuffel, S.F. McCormick, and L.N. Olson, Algebraic multigrid for higher-order finite elements, Journal of Computational Physics, 204(2), 520–532, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
72
Development of a flow stress model for metals using the strain rate / temperature superposition principle Ch. Husson*, J. Richeton†, S. Ahzi† *
Institut Supérieur d’Ingénierie de la Conception - Equipe ERMeP 27 rue d’Hellieule, F-88100 Saint-Dié-des-Vosges
[email protected] †
Université Louis Pasteur, IMFS-UMR 7507 2 rue Boussingault, F-67000 Strasbourg
[email protected] -
[email protected]
ABSTRACT The stress-strain response of metallic materials and alloys is influenced by the temperature at which deformation occurs and by the loading rate. To model this behavior under a wide range of strain rates and temperatures we propose to use the strain rate / temperature superposition principle: an increase in temperature will have the same effect on the yield stress as a decrease in strain rate. This type of approach has been recently proposed to model the yield behavior of solid polymers. Here we show that this approach can be extended to model the yielding and flow stress evolution in ductile metals. For a wide range of temperatures and strain rates, the superposition principle is applied for different metals such as copper and high strength steel. This comparison showed a good agreement with the experimental data found in the literature.
References [1] J. Richeton, S. Ahzi, L. Daridon, Y. Rémond, A formulation of the cooperative model for the yield stress amorphous polymers for a wide range of strain rates and temperatures. Polymer, 46, 6035-6043, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
73
Analysis of Elastic Body using Kalman Filter Finite Element Method Taku Kato*, Mutsuto Kawahara† *
Department of Civil Engineering, Chuo University Kasuga 1-13-27, Bunkyo-ku, Tokyo 112-8551, Japan
[email protected] † Department of Civil Engineering, Chuo University Kasuga 1-13-27, Bunkyo-ku, Tokyo 112-8551, Japan
[email protected]
ABSTRACT This research is the estimation of elastic body using the Kalman Filter Finite Element Method. The ground is always continuing a minute vibration. And it is very difficult to identify data about production of any actions. The Kalman Filter is the method of estimating unknown parameter using observation data distorted by noise. The Kalman Filter is the filtering algorithm presented by Kalman and Bucy in 1960’s, which is based on the stochastic process theory of the state space model and the orthogonal projection for the linear system. In the Kalman Filter, the system and observation noise are included. The system noise is error that arises in approximating basic equation. The state space model is consisted by system model equation and the observation equation. The system model equation can be expressed state of phenomena. And the observation equation is denoting relation between the actual observation data and the state value. The Kalman Filter is a calculation algorithm is estimation problem it is divided in three workspace shown as followed, (1) Prediction is the problem calculated optimal estimated values in the future, (2) Filtering is calculated it at the present, (3) Smoothing is calculated it in the past. The Kalman Filter can estimate the state value in time direction. However, the Kalman Filter cannot estimate the state value in space direction. If combine the advantage of the Kalman Filter and Finite Element Method, it can estimate not only in time but also in space direction. And it is the Kalman Filter Finite Element Method. For the temporal discretaization, the Newmark β method is used. And For the spatial discretaization, the Galerkin method is applied. As the numerical analysis, it is presented that the estimation of the quarry. The quarry is Futatsuisi-mountain in Miyagi Japan. The actual data is used from September 20th in 2005.
References [1] Hikawa, A., Kawahara, M. and Kaneko, N., Parameter Identification of Ground Elastic Modulus at Excavation Site of Tunnel. Vol.1, Research Report of Professor M. Kawahara Lab, pp72-83, 2004. [2] Kato, Y. and Kawahara, M., Kalman Filter Finite Element Method Applied to Elastic Body Using Tunnel Model, Research Report of Professor M. Kawahara Lab. [3] Komine, H., Kawahara, M. and Koizumi N., Application of First Order Adjoint Method to Parameter Identification, Research Report of Professor M. Kawahara Lab.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
74
Discontinuous Galerkin methods for nonlinear elasticity Adrian Lew∗, Alex Ten Eick† ∗Stanford University Durand 275, Stanford, CA, 94305-4040, USA
[email protected] † Stanford University Durand 212, Stanford, CA, 94305-4040, USA
[email protected]
ABSTRACT In this talk we present a general formulation for discontinuous Galerkin methods for nonlinear elasticity. We discuss the efficiency, implementation, and stabilization of the method, and illustrate the results with numerical examples, including convergence rates, behavior under nearly incompressible conditions and under severely large deformations. We illustrate the performance of the method with applications to biomechanics problems.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
75
A Rate Dependent Constitutive Model for Carbon-Fibre/Epoxy-Matrix Woven Fabrics Submitted to Dynamic Loadings S. Marguet∗, P. Rozycki†, L. Gornet† ∗Ecole Centrale de Nantes, GeM, UMR CNRS 6183 1 rue de la No BP92101, 44321 Nantes Cedex 3, France
[email protected] †Ecole Centrale de Nantes, GeM, UMR CNRS 6183 1 rue de la No BP92101, 44321 Nantes Cedex 3, France
[email protected],
[email protected]
ABSTRACT This paper deals with the modelling until rupture of composite structures made of carbon/epoxy woven fabrics and submitted to dynamic loadings. The mechanical behaviour of the woven ply appears to be orthotropic, strongly non linear and rate dependent. In the warp and fill directions the ply behaves in a way slightly non linear, elastic and brittle whereas in shear, it can be observed a progressive loss of rigidity of the elastic modulus combined with inelastic strains. In this work, and in order to take into account the previous physical phenomena, we have adapted and strongly coupled a viscoplastic model with a delayed damage mesomodel [1]. In each direction of fibres, a damage variable drives the failure. In shear, the association of a damage variable with a plastic strain allows the model to represent the non linear irreversible effects described above. Special attention is paid to ensure a good representativeness of the model compared with the experiments on a large range of strain rates. This results in the introduction of viscous elastic moduli. The constitutive equations are solved implicitly throughout a backward Euler scheme which is implemented by the mean of a Closest Point Projector algorithm. To identifiy the parameters, an optimization procedure based on the direct search method is carried out. It leads to an accurate behaviour of the model in both tensile and shear directions for strain rates evolving from at least 1.10−3 s −1 to 1.103 s −1 . Furthermore, to check the ability of the model to avoid strain localization phenomenon or mesh dependency, a campaign of simulations is performed on the classical example of a bar in tension. Finally, and in order to test the model on structural applications, both the impact on composite plate and the dynamic crushing of thin-walled tube are simulated and compared with some experimental results from [2] and [3]. The model developed in this study appears to be able to predict quite precisely the collapse of the structures from the initiation of a macroscopic cracks towards the rupture.
References ` O. Allix, J-F. Deu, ¨ D. Lev ´ eque, ˆ [1] P. Ladeveze, A mesomodel for localization and damage computation in laminates, Computer Methods in Applied Mechanics Engeneering, Vol 183, pp 105-122, 2000. [2] A.F. Johnson, A.K. Pickett and P. Rozycki, Computational methods for predicting damage in composite structures, Composites Science and Technology, Vol 61, pp 2183-2192, 2001. [3] A.G. Mamalis, D.E. Manolakos, M.B. Ioannidis, D.P. Papapostolou, On the response of thinwalled CFRP composite tubular components subjected to static and dynamic axial compressive loadings: experimental, Composite Structures, Vol 69, pp 407-420, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
76
Solution of viscoelasticity problems using special forms of elastic solutions Valery P. Matveyenko* *
Institute of Continuous Media Mechanics of Ural Branch of RAS Academician Korolev str., 1 Perm, 614013, Russia
[email protected]
ABSTRACT The Volterra method is widely used for solving linear quasistatic viscoelasticity problems. According to this method, the construction of the viscoelastic solution reduces to the replacement of elastic constants by Volterra operators and to further interpretation of operator relations. The transition from the elastic solution to the viscoelastic one is usually attended with great calculation difficulties encountered in interpretation of operator relations. One way to meet this challenge is to represent the solution of the elastic problem in the form suitable for further interpretation. The first sample of such representation belongs to Volterra. One of most effective methods to overcome these difficulties was suggested by A.A.Ilyushin. This work presents an approach that enters into this group. The variants of this approach are suggested to develop elastic solutions for uniform solid as a series in integer powers of an elastic constant (Ilyushin’s parameter) and as a series in integer powers of two elastic constants (Ilyushin’s parameter and the volume modulus). The variant of construction of elastic solutions for piecewiseuniform solids as a series in integer powers of elastic constants (Ilyushin’s parameters) of each component is developed. The obtained forms of elastic solutions are used to find solutions to the following viscoelastic problems: for uniform or piecewise-uniform (made of different viscoelastic materials) solid made of materials with hereditary–elastic properties under shear deformations and elastic properties under volume deformations. The mathematical convergence of the considered calculation procedures is proved. For numerical realization of the problems, the standard procedures of the finite-element method are used. The obtained numerical results demonstrate the efficiency of the applied calculation procedure. The results obtained from the solution of viscoelasticity problems are provided. The proposed method made it possible to discover a new qualitative effect associated with the time behavior of stresses in piecewise-uniform solids. The essence of the effect is that at constant or monotonic time variable external load the change in stresses may be of non-monotonic character.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
77
Finite elements method analysis of influence of contact phenomena on structure-subsoil interaction ´ Marcin Mazdziarz Institute of Fundamental Technological Research Warsaw,Poland
[email protected] ABSTRACT The contact between structure and subsoil is formulated by using 3D elasto-viscoplastic relationships incorporating pore pressure. Finite element implementation is then performed for the geotechnical structure, subsoil and contact relationships. Contacts elements with zero thickness are carefully developed, allowing for slip and stick. Solid isoparamtric elements are also developed. The novelty of the contribution consists of using elasto-viscoplastic model incorporating pore pressure for 3D contact. Using implemented spatial elements in the program HYDRO-GEO elasto-viscoplastic analysis of interaction between structure and subsoil was carried out. Earth dam interacting with concrete weir and excursion trough in one of Polish earth dams (Dobczyce) was analyzed. Simulation of deformation of structure and slide of soil on surface of the retaining wall was studied. The goal of this study was to examine both from theoretical and numerical point of view the influence of contact phenomena on structure-subsoil interaction. The numerical analysis was carried out by using finite element methods including spatial contact elements with zero thickness. 3D formulation of the interacting structure with subsoil was developed. The program HYDRO-GEO enables to perform numerical calculations of the considered complex contact problem in the 3D case. The paper can be divided into two essential parts. The first part is concerned with discretized 3D description of basic relationships by using the finite element method. To do this 3D solid isoparametric elements were introduced. Pore pressure was taken into account. Spatial contact finite elements were developed and incorporated into the program. These elements cover elasto-viscoplastic contact behavior and take into account pore pressure, slip and stick range. In numerical part of the paper the developed discrete model was implemented into the computer program HYDRO-GEO. Then the elasto-viscoplastic interaction between structure and subsoil can be analyzed. A complex system consisting of the earth dam and concrete weir was studied (one of Polish earth dams in Dobczyce).
References ´ [1] Marcin Mazdziarz, Influence of contact phenomena on structure-subsoil interaction: finite elements method analysis, PhD thesis, Politechnika Warszawska, Warszawa (in Polish), 2003. [2] Zienkiewicz O. C., Taylor R. L. , The Finite Element Method. Vol 1-3. Oxford: ButterworthHeinemann , 2000.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
78
Simulation of Inelastic Deformation of Polyethylene in Multiaxial State of Stress by Viscoelastic Constitutive Equtaion Mamoru Mizuno* and Yukio Sanomura† *
Dept. Machine Intelligence and Systems Engineering Akita Prefectural University Tsuchiya, Yuri-Honjo, Akita 015-0055, Japan
[email protected] †
Dept. Mechanical Engineering Tamagawa University Tamagawa-Gakuen, Machida, Tokyo 194-8610, Japan
[email protected]
ABSTRACT Polymers show significant strain recovery after reversal of the loading direction, and conventional constitutive equations can not describe inelastic deformations including the strain recovery properly. Then the present authors have proposed a viscoelastic constitutive equation for polyethylene in order to describe the inelastic deformations. In the formulation, a total strain was assumed to be the sum of an elastic strain and a viscous strain. The elastic strain was subjected to the Hooke’s law, and the viscous strain was derived from the kinematic hardening creep theory of Malinin and Khadjinsky, which was combined with the nonlinear kinematic hardening rule of Armstrong and Frederick. In order to describe the strain recovery, a loading surface was defined in a viscoelastic strain space, and a new parameter was defined by using the loading surface. Then the nonlinear kinematic hardening rule was modified by using the parameter. Inelastic deformations in a uniaxial state of stress were simulated by using the constitutive equation and the validity of the formulation and the modification was verified by comparing the simulations with experimental results of polyethylene. Then inelastic deformations under typical cyclic loadings in the uniaxial state of stress were predicted, and features of the deformations were discussed. In general, the viscoelastic constitutive equation will be employed for structural analyses such as a FEM. Thus the applicability and the capability of the constitutive equation to predict deformations in a multiaxial state of stress are important. In the present paper, inelastic deformations of polyethylene in a two-axial state of stress by the combination of a normal stress and a shear stress are simulated by using the viscoelastic constitutive equation. As a loading condition, proportional and non-proportional strain paths under the total strain control at constant strain rate are considered. Inelastic deformations under cyclic loadings are focused on in particular. Results of the simulations are compared with experimental results of polyethylene and the validity of the constitutive equation is verified in the multiaxial state. And features of the inelastic deformations of polyethylene are inspected by simulations under various loading conditions.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
79
Modeling of granular media by the 2D discrete lattice Igor S. Pavlov* *
Mechanical Engineering Research Institute of the Russian Academy of Sciences 85, Belinsky street, 603024, Nizhny Novgorod, RUSSIA
[email protected]
ABSTRACT A two-dimensional model of a granular medium is considered that represents a square lattice consisting of uniform round particles. The particles have both translational and rotational degrees of freedom. Each particle (granule) is supposed to interact directly with eight nearest neighbours in the lattice [1]. The nonlinear governing equations describing propagation and interaction of waves of various types in such a medium have been derived for a cubic potential of elastic interactions between the particles in the discrete and continuum approximations. The discrete equations are valuable, particularly, for numerical simulation of nonlinear wave processes in granular media. The continuum approximations of the model at issue are convenient for its comparison with known theories of solids. The continuum equations do not coincide with the classical theory of elasticity due to additional equation for the rotational wave. Such a wave exists when the frequency is larger than a threshold value. Its dispersion properties are similar to dispersion properties of the spin wave in a magnetelastic medium. From the numerical estimations of the rotational wave velocity in some cubic crystals follows that, as a rule, it is less than the translational wave velocities. When microturns of the particles are absent, the linear parts of the governing equations of the first continuum approximation degenerate into Lame equations for anisotropic medium with the cubic symmetry. The governing equations are structurally similar to equations of the anisotropic Cosserat continuum with centrally symmetric particles. However, the longitudinal wave velocity does not depend on the medium structure in the Cosserat continuum, while such dependence presents in the considered model. The last fact enables to explain, particularly, experimentally observing variations of this wave velocity when size of granules grows. The governing equations of the second (quasicontinuum) approximation contain summands with higher-order derivatives and give explanation to appearance of the longitudinal wave dispersion. The Cosserat theory is unable to explain this effect.
References [1] I.S. Pavlov, A.I. Potapov, and G.A. Maugin, A 2D Granular Medium With Rotating Particles. Int. J. of Solids and Structures, 2005 (in print).
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
80
&U\VWDOSODVWLFLW\EDVHGLGHQWLILFDWLRQRIDQLVRWURSLFVWUDLQUDWHSRWHQWLDOV IRUVKHHWPHWDOIRUPLQJVLPXODWLRQ
05DEDKDOODK %%DFURL[6%RXYLHU7%DODQ
/300&156805(16$0 UXH$)UHVQHO0HW]&HGH[)UDQFH PH]LDQHUDEDKDOODK#PHW]HQVDPIUDQGWXGRUEDODQ#PHW]HQVDPIU /3070&1568358QLYHUVLW\3DULV $Y-%&OpPHQW9LOOHWDQHXVH)UDQFH EULJLWWHEDFURL[#OSPWPXQLYSDULVIUDQGVDOLPDERXYLHU#OSPWPXQLYSDULVIU
$%675$&7
8QGHUWKHFRQGLWLRQVRIWKHFRQYH[LW\RIWKH\LHOGVXUIDFHDQGWKHQRUPDOLW\RIWKHIORZUXOH>+LOO @ SURYHG WKH H[LVWHQFH RIWZR FRQYH[ GXDO SRWHQWLDOV ψ İ S RU ϕ ( ı′) IURP ZKLFK WKH VWUHVV WHQVRUFDQEHGHULYHGDVDIXQFWLRQRIWKHVWUDLQUDWHWHQVRUDQGUHFLSURFDOO\7KHSODVWLFDQLVRWURS\RI FROGUROOHGVKHHWPDWHULDOVGXHWRWKHLULQLWLDODQGLQGXFHGFU\VWDOORJUDSKLFWH[WXUHVFDQEHGHVFULEHG E\DQDGMXVWPHQWRIWKHFRHIILFLHQWVRIWKH\LHOGIXQFWLRQ ϕ ( ı′ ) RUWKHVWUDLQUDWHSRWHQWLDO ψ İ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¶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
( )
( )
5HIHUHQFHV
>@ 5+LOO-0HFK3K\V6ROLGVSS >@ 0$UPLQMRQDQG%%DFURL[$FWD0HFKDQLFDSS >@ )%DUODWDQG.&KXQJ0RGHOOLQJDQG6LPXODWLRQLQ0DWHULDOV6FLHQFHDQG(QJLQHHULQJSS >@ ) %DUODW DQG . &KXQJ 3URF RI WKH WK (VDIRUP &RQIHUHQFH RQ 0DWHULDO )RUPLQJ (G ' %DQDELF&OXM1DSRFD5RPDQLDSS
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
81
A geometric approach to the algorithmic tangent stiffness G. Romano∗, M. Diaco†, R. Barretta† ∗ Dipartimento di Scienza delle Costruzioni (DiSCo)
Universit`a di Napoli Federico II, via Claudio 21- 80125 Napoli, Italy
[email protected] †Dipartimento di Scienza delle Costruzioni (DiSCo) Universit`a di Napoli Federico II, via Claudio 21- 80125 Napoli, Italy
[email protected] -
[email protected]
ABSTRACT The elastoplastic tangent stiffness is the linear operator which provides the stress rate corresponding to a prescribed strain rate. As such, it plays a central role in the computational aspects of elastoplastic problems. According to the usual approach to the nonlinear evolutive analysis of elastoplastic models, a finite time-step is considered and the evolution law describing the constitutive behavior is reformulated as a finite step flow rule. The algorithmic tangent stiffness was first introduced by Simo and Taylor in [1]. They showed that the adoption of the algorithmic tangent stiffness leads to a significant improvement of the asympthotic convergence rate. The expression of the algorithmic tangent stiffness provided in [1], and in all the subsequent references to their contribution, was based on an explicit formulation of the elastoplastic constitutive law in terms of a plastic scalar multiplier. The geometrical analysis developed in the present paper is based on a formulation of the constitutive problem in terms of the nonlinear projector, in complementary elastic energy, on the convex elastic domain. The algorithmic tangent stiffness is evaluated as the composition between the derivative of the nonlinear projector and the elastic stiffness. The key point consists in the evaluation of the derivative of the nonlinear projector. A direct geometric argument, based on hypersurface theory, shows that the derivative can be expressed as the difference between the linear projector on the hyperplane tangent at the trial stress point and the shape operator of the parallel hypersurface passing thru the trial stress-state, multiplied by the distance between the trial stress and the projected stress, evaluated in the complementary elastic norm. The composition of the linear projector with the elastic stiffness is in fact the rate elastoplastic tangent stiffness. Since the analytic expression of the parallel hypersurface thru the trial stress point is available only in special cases, an effective procedure consists in substituting it with the level set of the yield function passing thru the trial stress point. In this way, the exact expression of the algorithmic stiffness is got when the level sets of the yield function are homothetic hypersurfaces, as in von Mises plasticity criterion, and a simple useful approximation is obtained in the general case. Indeed the proposed procedure greatly simplifies the computations while preserving the benefit of an improved convergence rate, since it takes effectively into account the curvature of the yield hypersurface, thus leading to a reduced tangent stiffness, in comparison with the rate tangent stiffness.
References [1] J.C. Simo, R.L. Taylor, Consistent tangent operators for rate-independent elastoplasticity, Comp. Meth. Appl. Mech. Engrg. , 48, 101–118, 1985.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
82
Parallel Computation of 3D Problems of the Dynamics of Elastic-Plastic Granular Material under Small Strains Vladimir M. Sadovskii, Oxana V. Sadovskaya∗ Institute of Computational Modelling SB RAS Akademgorodok, Krasnoyarsk, Russia, 660036 ∗
[email protected] ABSTRACT A process of waves propagation in elastic-plastic granular material under small strains is described on the basis of a new rheological model taking into account different resistance of the material with respect to tension and compression [1]. This model leads to the system of nonlinear partial differential equations of non-classical type which has an evident structure for numerical realization. Parallel decomposition of the used shock-capturing numerical method [2] is founded on the space-variable decomposition procedure. The proposed algorithm is accomplished as a program system for supercomputers with parallel architecture by means of SPMD (Single Program – Multiple Data) technology in Fortran-90 with the use of MPI (Massage Passing Interface) library. Various variants of 1D, 2D and 3D division of the spatial computational domain between the computational nodes are used. The program system allows to simulate a propagation of elastic-plastic waves generated by mechanical impacts in a body, aggregated of an arbitrary number of heterogeneous blocks with curvilinear boundaries. The exact one-dimensional solutions with plane shock waves are used for testing. Some problems of the waves refraction on the interior surfaces between blocks of granular materials with different mechanical properties are solved.
Stress field in different time moments
By means of the numerical experiments it is shown that the plane fronts of two waves, bending due to inhomogeneous loosening, can be reflected with the formation of transverse cumulative splash. The curved fronts of shock waves for different time moments and the cumulative splash (a typical zone of the compressive stresses, moving bottom-up) are represented in the Figure.
This work was supported by the grant of the Russian Foundation for Basic Research no. 04-01-00267, the Complex Program of the Presidium of RAS no. 14 “Fundamental Problems of Informatics and Informational Technologies” and the Russian Science Support Foundation.
References [1] V.M. Sadovskii, O.V. Sadovskaya, Parallel Computation of Elastic-Plastic Waves Propagation in Granular Material. Proc. of the 7th Intern. Conf. on Mathematical and Numerical Aspects of Wave Propagation. Brown University, Providence, 223–225, 2005. [2] O.V. Sadovskaya, Shock-Capturing Method as Applied to the Analysis of Elastoplastic Waves in a Granular Material. Comput. Math. & Mathematical Phys. 44, 1818–1828, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
83
A hyperelastodynamics ALE formulation based on spatial and material forces. Z. Uthman, H. Askes University of Sheffield, Department of Civil and Structural Engineering. Mappin Street, Sheffield S1 3JD, United Kingdom
[email protected] [email protected]
ABSTRACT This contribution aims at providing the formulation and implementation details of arbitrary Lagrangian Eulerian hyperelastodynamic problem classes. This ALE formulation is based on the dual balance of momentum in terms of spatial forces (the well-known Newtonian forces) as well as material forces (also known as configurational forces). The balance of spatial momentum results in the usual equation of motion, whereas the balance of the material momentum indicates deficiencies in the nodal positions, hence providing an objective criterion to optimize the finite element mesh. The main difference with traditional ALE approaches is that the combination of the Lagrangian and Eulerian description is no longer arbitrary, in other words the mesh motion is no longer user defined but completely embedded within the formulation. The present work aims at developing spatial and material variational equations based on the Hamiltonian principle. These equations will be discretised to obtain the weak form of the momentum and continuity equations. The discretized ALE Hamiltonian equations of the spatial motion problem introduces the balance of the discretised spatial momentum and the discretised spatial continuity equation while the corresponding material motion problem defines the balance of the discretised material (or configurational) momentum and the discretised material continuity equation. We will deal with two systems of partial differential equations: the scalar continuity equation and the vector momentum equation. The momentum and continuity equations will then be linearised. The time integration of both the spatial and the material equations is performed with the Newmark scheme. A monolithic solution strategy solving the spatial and the material momentum equations simultaneously has been carried out while updating of the spatial and the material densities was attained through solving the spatial and material continuity equations (mass conservation). The solution defines the optimal spatial and material configuration in the context of energy minimization.
References [1] T. Belytschko, W.K. Liu and B. Moran. Nonlinear Finite Elements for Continue and Structures. John Wiley & Sons Ltd, 2001. [2] E. Kuhl and P. Steinmann, A hyperelastodynamic ALE formulation based on referential, spatial and material settings of continuum mechanics: Acta Mechanica, 174, 201–222, 2005. [3] E. Kuhl, H. Askes and P. Steinmann, An ALE formulation based on spatial and material settings of continuum mechanics. Part 1: Generic hyperelastic formulation. Comput. Methods Appl. Mech. Engrg, 193, 4207-4222, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
84
Monoharmonic Approach to Investigation of Heat Generation in The Viscoplastic Solids under Harmonic Loading Yaroslav A. Zhuk Timoshenko Institute of Mechanics 3, Nesterov str, Kiev 03057, Ukraine
[email protected]
ABSTRACT Intensive forced vibration of structural elements can be accompanied with significant temperature rise (heating) caused by internal dissipation of mechanical energy. Therefore, the thermomechanical coupling can cause the degradation in material properties, high strains and stresses and results in fracture of various engineering structures. In studying the nonstationary, in particular resonant, processes, it is important to take into account inelastic deformation and heat emission [1]. Indeed, the thermoviscoplastic behavior of the material and the coupling of the mechanical and thermal fields may affect substantially the characteristics of vibration dampers for engineering structures. An approach to the solution of coupled problems of vibrations and dissipative heating of viscoplastic bodies is developed. Two problem statements are elaborated: “exact” and “ approximate” ones. The former statement consists of universal balance equations of thermodynamics and constitutive equations derived from the general thermodynamic theory of viscoplastic bodies with internal state variables. For this aim the theory version that corresponds to the Bodner-Partom generalized flow theory is used. The approximate or monoharmonic problem statement for the case of steady-state vibrations under the harmonic loading is obtained by the application of modified harmonic linearizing technique to the initial system of equations. Thereby the subsystem of mechanical equations is formulated in the complex-value form and material properties are described by means of amplitudedependent complex-value moduli. Numerical technique for the solution of the problems of vibration and dissipative heating of spatial and thin-wall elements of structures are developed. They are based on the iterative linearization procedures in association with FEM. The capabilities of the monoharmonic approach are studied by the example of the resonant and quasistatic vibrations and dissipative heating of a viscoplastic disk excited by a harmonic load [2].Additional attention is paid to the case of inhomogeneous (layered) solids. Physical and mechanical behavior of such systems is very complex because of the heterogeneity of the stress-strain state. Modeling such a behavior is additionally complicated by the necessity of allowing for the coupling of the mechanical and thermal fields when cyclic loading is intensive and for dynamic effects, in particular, when intensive vibrations occur in the quasistatic or resonant domain. Comparing the solutions obtained in the frame of the exact and approximate statements demonstrates high accuracy of the monoharmonic model for the problems investigated (axisymmetric vibrations and heating of layered or homogeneous viscoplastic disk and rectangle).
References [1] I. Senchenkov, Y Zhuk and V. Karnaukhov, Modeling the thermomechanical behavior of physically nonlinear materials under monoharmonic loading. International Applied Mechanics, 40, 943-969, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
85
A continuous Galerkin finite element method for thermoelasticity without energy dissipation Swantje Bargmann∗ , Paul Steinmann∗ ∗ Chair
of Applied Mechanics, University of Kaiserslautern P.O. Box 3049, 67653 Kaiserslautern, Germany {bargmann,ps}@rhrk.uni-kl.de ABSTRACT
The classical thermal theory based on Fourier’s law leads to a diffusive regime. Contrary to that Green and Naghdi [3] developed a theory of thermoelasticity without energy dissipation whose temperature evolution equation is hyperbolic. Among others, the introduction of a new internal variable, i.e. the thermal displacement α with α˙ = T , leads to the theory without energy dissipation, or also called theory of type II, which does not involve energy dissipation. It incorporates thermal wave propagation in a very consistent way and is capable of modeling the second sound phenomenon. The governing equations of the dynamic, linear theory of isotropic and homogeneous thermoelasticity without energy dissipation are the temperature equation a (1) ρcbT˙ = ρr + ρ κ∆α − ρbT0 3wKI : ε˙ b and the balance of linear momentum ˙ = divσ + b, [ρv] (2) where the entropy flux p = − ρκ b ∇α is determined by the same potential which determines the mechanical stresses σ. This contribution concentrates on numerical aspects of the Green-Naghdi theory of type II. In order to perpetuate the consistency of their theory to the numerical setting we resort to a Galerkin finite element method in space and in time. As the theory itself does not admit energy dissipation, conserving time integration schemes that inherit the underlying conservation principles are of great interest. Customary implicit time-stepping schemes fail to conserve major invariants, for example the total energy. The coupled dynamic system of equations is discretized in time within the framework of finite element methods using a continuous Galerkin (cG) method. In general, the cG-method has proven to qualify well for hyperbolic problems. This fact also holds true for hyperbolic heat conduction and linear thermoelastostatics [1, 2]. The cG(k)- method approximates trial functions piecewise and continuously with polynomials of degree k and test functions piecewise and discontinuously across the element boundaries with polynomials of degree k − 1. The coupled system is solved monolithically. A numerical example is investigated in order to evaluate the performance of the proposed method.
References [1] S. Bargmann and P. Steinmann, Finite element approaches to non-classical heat conduction in solids. Comp. Model. Eng. Sci. 9(2), 133–150, 2005. [2] S. Bargmann and P. Steinmann Theoretical and computational aspects of non-classical thermoelasticity. submitted [3] A.E. Green and P.M. Naghdi A re-examination of the basic postulates of thermomechanics. Proc. R. Soc. Lond. 432, 171–194, 1991.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
86
The Model Coupling Liquid Bridge Between Ellipsoidal Grains Jolanta Báaszczuk*, Zbigniew DomaĔski† Institute of Mathematics and Computer Science, Czestochowa University of Technology Dabrowskiego 73, 42-200 Czestochowa, Poland *
[email protected] †
[email protected]
ABSTRACT Granular materials are the subject of scientific studies due to their unusual physical properties which differ significantly from solid and liquid states of matter. In this paper we are interested in the role played by humidity on static and dynamic properties of systems consisting of non-spherical grains. The addition of a liquid to the material adds an attractive force to the system and then, increased its stability. Quantitative description of wetting thermodynamics is sensitive not only to the contact angle between solid and the liquid but also to the to the shape of grains and thus we analyze ellipsoidal grains and we assume that liquid spreads uniformly over the whole grain’s surface. We consider a model grain’s surface consisting of asperities of equal size uniformly distributed over the grain’s surface. We also suppose that each asperity may be either totally filled with liquid or stay empty. Thus, in our approach we consider two regimes of the inter-grain adhesive force versus volume of the wetting layer. For very small amount of liquid, the capillary force comes from the fluid accumulated around a small number of asperities at which two neighbouring grains are in contact. If the fluid wets the surface of the grains then all asperities are filled and inter-grain adhesive energy is determined mainly by the macroscopic curvature of the grain, and the surface roughness does not play a crucial role. In this case, the distribution of values of inter-grain energies is determined only by macroscopic quantities, i.e. the geometry of grains and material characteristics. Using toroidal approximation for the shape of liquid bridges and some simple probabilistic arguments we analyze the influence of amount of liquid on mutual grain – grain orientation. We found two energetically favorable orientations: one with mutually parallel and second with perpendicular axes of contacted grains.
References [1] J. Báaszczuk, Z. DomaĔski, Liquid – induced glassy behaviour of dense non-spherical grain ensembles, 16th International Conference on Computer Methods in Mechanics, CMM 2005, Publishing House of Czestochowa University of Technology, 347-348, 2005. [2] J. Báaszczuk, Z. DomaĔski, Toroidal approximation for capillary bridges between ellipsoidal grains, Scientific Research of the Institute of Mathematics and Computer Science 1(4) 2005, Publishing House of Czestochowa University of Technology, 13-17, 2005. [3] J. Báaszczuk, Dynamics and statics of packing granular materials. PhD thesis, Czestochowa University of Technology, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
87
Reliability of Wavelet Packet System Identification Maik Brehm ∗, Christian Bucher† ∗Institute of Structural Mechanics, Bauhaus-University Weimar
Marienstraße 15, 99423 Weimar, Germany
[email protected] † Institute of Structural Mechanics, Bauhaus-University Weimar
Marienstraße 15, 99423 Weimar, Germany
[email protected] ABSTRACT In recent years various methods have been developed to identify structural system parameters. One approach for dynamical system identification is the application of wavelets. [1] uses Daubechies wavelets within a wavelet transformation algorithm and [2] investigates the biorthogonal wavelet transformation. The basic challenge of such wavelet-based methods is the determination of an optimal set of approximation and detail coefficients to set up the linear equation system for the identification of the unknown parameters. A major improvement compared to the simple wavelet transformation is achieved by using wavelet packets. [3] presents an automatic best basis search to determine a suitable set of coefficients. However, this algorithm is not unique and identifies only one of the best sets of coefficients. Due to the frequency decomposition of the wavelet analysis all these methods can handle a high noise level. Of course, the quality of the solution still depends on the noise level. The current practice of verifying the results are based on the known parameters or those obtained by other methods. Both ways are suboptimal to identify parameters of a genuine structure. This study investigates the possibilities to increase the reliability of the identification of the system parameters by means of wavelet transformation and the wavelet packet algorithms without the knowledge of the correct solution. Condition numbers and optimization methods are used to detect the best set of coefficients to set up an optimal equation system. Furthermore, the presented methods are discussed regarding their challenges and feasibilities for practical system identification. The developed algorithms have been implemented in the SLang Software package, which is available at the Bauhaus-University Weimar for research activities.
References [1] V. Zabel, Applications of Wavelet Analysis in System Identification. PhD Thesis, BauhausUniversity Weimar, 2003. [2] M. Brehm et al. , Applications of Biorthogonal Wavelets in System Identification. P. Neittaanm¨aki, T. Rossi, K. Majava, and O. Pironneau (eds.) Proceedings of the 4th European Congress on Computational Methods in Applied Sciences and Engineering, Jyv¨askyl¨a, 24-28 July, 2004. [3] M. Brehm et al. , Applications of Wavelet Packets in System Identification . 76. Annual Conference of the International Association of Applied Mathematics and Mechanics (GAMM), University of Luxembourg, March 28 - April 1, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
88
An attempt to simulate more precisely the behavior of a solid body using new energy conservation equation for fully coupled thermal structural analysis L. Écsi*, P. ÉlesztĘs† †*
Dept. of Strength of Mater, Faculty of Mech. Eng, Slovak University of Technology in Bratislava Námestie slobody 17, 812 31 Bratislava, Slovak Republic *
[email protected], †
[email protected]
ABSTRACT In this paper a numerical study of solid bar behavior under various mechanical loads is presented using fully coupled thermal structural analysis with large strain / large deformation formulation. The analysis is based on a new energy conservation equation [2], which the authors believe represents the most complete formulation of the first principle of thermodynamics in contemporary computational mechanics. In the numerical analysis was used the finite element method (FEM), utilizing the updated Lagrange method and the extended NoIHKH material model [1],[3], modified for large strain / large deformation cyclic plasticity of metals. In the stress update calculation [4] was used the Jaumann objective rate in the form of the Green-Naghdi objective rate, formulated with the aid of the rotated Cauchy stress tensor. The rotation tensor was expressed with the Rodriguez formula. The case was implemented into a finite element code using “proper” linearization, which means that no simplifications were used in a gradient or an element volume expression in the current configuration. The presented results represent some of the first outcomes of the fully coupled thermal structural analysis utilizing the new energy conservation equation with large strain/ large deformation formulation, which the authors consider to be positive. The new energy conservation equation can still be improved by introducing a heat source in it to take into account the amount of energy dissipated into heat during plastic deformation, but to propose a mathematical formula for the heat source is rather an experimental problem than a mathematical one. If the new energy conservation equation proves to be experimentally correct, in the future more complex problems will be able to be solved, mainly in the area of fast/ultra fast thermoelasticity or thermoplasticity.
References [1] L. Écsi, Extended NoIHKH model usage for cyclic plasticity of metals, In proceedings of the 7th. International Conference on Applied Mechanics (CD), Hrotovice, Czech Republic, 29.March1.April, 2005. [2] L. Écsi, Numerical behavior of a solid body under various mechanical loads using finite element method with new energy balance equation for fully coupled thermal structural analysis, In proceedings of the 6th. International Congress on Thermal Stresses, Vienna, Austria, 26-29. May, 2005, Vol. II, pp. 543-546. [3] J. Lemaitre, Handbook of Materials Behavior Models 1, Academic Press, NY, 2000 [4] E.A. Souza, D. Peric, D.R.J. Owen, Computational Plasticity, Small and Large Strain Finite Element Analysis of Elastic and Inelastic Solids, Swansea, to be published
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
89
Mathematical aspects of the initial-boundary value problems in nonlinear thermoelasticity of simple and non-simple materials J.A. Gawinecki Institute of Mathematics and Cryptology, Faculty of Cybernetics Military University of Technology Str. Kaliskiego 2, 00-908 Warsaw, Poland
[email protected] ABSTRACT In this lecture we report on diffrent coupled thermoelastic systems. They are models for the description of elastic heat conductive media. We will consider a coupled second-order hyperbolic system describing the thermoelasticity of simple materials and a coupled parabolichyperbolic systems of thermoelasticity of non-simple materials. It is known that the classical thermoelasticity theory (hyperbolic-parabolic) leads to a parabolic diffrential equation for the temperature distribution in rigid heat conductors. This implies that thermal perturbations are felt instantaneously in every part of the body. Although, at first sight, this outcome seems to contradict the physical intuition, it can be justified by resorting to the fact that molecular motion, which places a crucial part in transport phenomena, is very rapid except at extremely low temperatures. Hencen finite velocity of propagation for thermal perturbations is usually non-observable unless experiments are performed in some neighborhood of absolute zero as in the case of liquid helium. In fact, thermal waves, commonly known as second sound, are detected in some metals cooled approximately down to 20◦ K. In our lecture we consider the theory of thermoelasticity by considering the temperature-ratedependence and assigning an appropriate constitutive function to the entropy flux. Such a theory leads to a hyperbolic differential equation for thermal perturbations different from the equation describing propagation of thermal perturbation in classical thermoelasticity which is parabolic one. We consider also the nonlinear hyperbolic-parabolic system of coupled partial differential equation of fourth order describing the thermoelasticity of non-simple materials. We are interested in both the lineralized and the non-linear systems looking for the description of the asymptotic behavior of smooth solutions, for smoothing effects of the systems and specifically for the non-linear systems for the global existence in time of solutions. For hyperbolic systems it is well known that in many cases locally existing smooth solutions tend to develop singularities in finite time. The basic problem for the system in question here is whatever and in which way the added damping by heat conduction or viscosity will assure the global existence of solutions. From this point of view we investigate the global existence in time for large data in nonlinear thermoviscoelasticity.
References 1. 2.
J. A. Gawinecki, Global solutions to initial value problems in nonlinear hyperbolic thermoelasticity. Dissertationes Math. 344, 1–51, Warsaw Poland. J. A. Gawinecki. Global existence of solution for non-small data to non-linear spherically symmetric thermoviscoelasticity, Math. Met. Appl. Sci. 26, 970–936, 2003.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
90
Effect of Parameter Uncertainties on a Vibro-Acoustic Design M. Guerich, S. Ben Chaabane Pôle Universitaire Léonard de Vinci ESILV – DER MS 92916 Paris la Défense Cedex {Francemohamed.guerich, samir.benchaabane}@devinci.fr
ABSTRACT The prediction of vibro-acoustic behaviour of structures is of the greatest interest for the design of less noisy machines. In the low frequency (LF) range, using finite element method (FEM) and/or boundary element method (BEM) in general insure such predictions. In the case where the FEM is used, in general this corresponds to an internal vibro-acoustic coupling problem, the vibro-acoustic model is constituted of structural and acoustical models. The structural model is performed using finite element of plates and/or shells and the acoustical model is constituted of volumic finite elements. When an internal vibro-acoustic coupling problem is studied, the modal method is in general used. It consists of the computation of structural and acoustical modes, which will be used as a basis of the displacement for the structure and of the pressure for the fluid. These modes depend on mechanical properties of the structure and the cavity and on geometric dimensions. Moreover, to predict the vibro-acoustic behaviour of the coupled system, appropriate caseload and cinematic boundary conditions must be considered. Thus, the vibro-acoustic model involves in general, a big number of parameters. These parameters can be given with some uncertainties.The purpose of this paper is to measure the effect of these uncertainties on the vibro-acoustic behaviour of the whole system. With such study the reliability of the vibro-acoustic system can be evaluated. To illustrate these effects, we have considered a simple case of vibro-acoustic response of a coupled plate-cavity to a harmonic mechanical force in a LF range.Some of the design parameters are considered as uncertain. These uncertainties are represented by Gaussian distributions of the parameters.A large sample of design points is defined and the responses are evaluated in these design points. The distribution of the response is then extracted and its coefficient of variation (COV) is compared to those of the parameters. Failure criteria (pressure level on the cavity and/or cinematic energy of the structure) can be defined to estimate the failure probability of the design.
References [1] Morand J.P., Ohayon R., Fluid structure interaction, Masson, Paris, 1992. [2] Lesueur C., Rayonnement acoustique des structures (in French), Eyrolles, Paris, 1988. [3] Guerich M., Hamdi M.A, A Numerical Method for Vibro-Acoustic Problems with Incompatible Finite Element Meshes Using B-Spline Functions, JASA, 105 (3), 1999, pp 1682-1694. [4] Melchers R. E., Structural Reliability Analysis And Prediction, Jhon Wiley & Sons Chichester, 1999 [5] ", S. Bouabdallah, S. Ben Chaabane, S. Missoum, Analyse fiabiliste du procédé de mise en forme des tôles minces, 7ème COLLOQUE NATIONAL EN CALCUL DES STRUCTURES, Giens 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
91
A numerical method for solid-liquid interaction Goodarz Khodabakhshi, Vahid Nassehi, Leila Shojai, Richard J.Wakeman Chemical Engineering Department Loughborough University, Loughborough Leicestershire, LE11 3TU, United Kingdom {g.khodabakhshi, v.nassehi, l.shojai, r.j.wakeman}@lboro.ac.uk
ABSTRACT This paper deals with the mathematical modelling of coupled fluid flow and solid deformation problems. A novel mathematical technique for linking of the two sets of governing equations in a single model has been proposed. Results obtained by this technique using a range of power-law index for fluid flow simulation and elasticity modulus for the solid displacement are presented and discussed . Changing the rheological behaviour of the fluid has a significant effect on the deformation of the solid. These results are found to be self consistent and as expected from a theoretical point of view.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
92
Computational Simulation of Irreversible Deforming and Fracture of Damageable Solids and Structures Alexey B. Kiselev, Olga V. Nekhaeva, Anton V. Privalsky Mechanics and Mathematics Faculty of Moscow M.V. Lomonosov State University Leninskie Gory, MSU, Main Bldg, Moscow 119992, Russia
[email protected]
ABSTRACT Thermomechanical processes, which proceed in deformable solids under intensive dynamic loading, consist of mechanical, thermal and structural ones, which correlate themselves. The structural processes involve the formation, motion and interaction of defects in metallic crystals, phase transitions, the breaking of bonds between molecules in polymers, the accumulation of microstructural damages (pores, cracks), etc. Irreversible deformations, zones of adiabatic shear and microfractures are caused by these processes. Dynamic fracture is a complicated multistage process including an appearance, evolution and confluence of microdefects and a formation of embryonic microcracks, pores, their grow up to the break-up of a bodies with division into separate parts. The present paper include new results in the next scopes: 1) development the thermodynamically correct mathematical models of damageable thermoelastoviscoplastic medium (microfracture); 2) development the methods for determination of “nonstandart” constants of medium models, connected with microfracture of material; 3) numerical simulation of destruction (fragmentation) of constructions (macrofracture); 4) numerical investigation of some problems for damageable solids and structures (dynamical deforming and fracture of thick-walled cylindrical and spherical shells under explosion; dynamical deforming and fracture of thick-walled two-layer shell, filled with liquid, under impact and high velocity penetration; the problems of dynamic deforming and destruction of an oil-holding layer in gydraulic fracturing). Some of previously obtained results in consideration domains are published in the papers [1-5]. Russian Foundation for Basic Research (grants No. 06-01-00185 and No. 05-08-01435) and ISTC (grant No. 2992) are acknowledged for financial support.
References [1] A.B. Kiselev, Mathematical modeling of dynamical deformation and combined microfracture of a thermoelastoviscoplastic medium, Moscow Univ. Mech. Bull., 53, No. 6, 32-40, 1998. [2] A.B. Kiselev, A.A. Lukyanov and M. Thiercelin, Numerical simulation of dynamic propagation of curvilinear cracks of hydraulic fracturing, Moscow Univ. Mech. Bull., 59, No. 1, 36-41, 2004. [3] A.B. Kiselev and O.V. Nekhaeva, Numerial modeling of dynamical deformation and fracture of a thick-walled spherical shell, Moscow Univ. Mech. Bull., 59, No. 5, 53-58, 2004. [4] A.B. Kiselev and O.V. Nekhaeva, Numerial simulation of dynamical deformation and fracture of a thick-walled cylindrical shell, Moscow Univ. Mech. Bull., 60, No. 2, 33-37, 2005. [5] A.B. Kiselev and O.V. Nekhaeva, Mathematical modelling of dynamic processes of irreversible deforming, micro- and macrofracture of solids and structures, 11th Int. Conference on Fracture (Turin, Italy, March 20-25, 2005), Abstract Book, Turin, CCI, 228 (Proc. on CD-ROM, 6 p), 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
93
Solution of the coupled light-mechanical problems Miroslav Kropáþ*, Justín Murín† * Visteon-Autopal, s.r.o. Nový Jiþín Lužická 14, 74101 Nový Jiþín, Czech Republik
[email protected] †
Department of Mechanics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology Ilkoviþova 3, 812 19 Bratislava, Slovak Republik
[email protected]
ABSTRACT
Dynamic optical systems (e.g. automotive headlights) provide the changes of their optical parameters, on the one hand by the motion of the whole lighting unite or on the other hand by the rigid motion of the individual elements of the optical system [1]. Our principle of reflector area controlled deformation is a new point of view in a required light beam modification of headlights during the car drive. It is necessary to solve coupled light-mechanical task to examine the influence of reflector area deformation on the quality of beam pattern by numerical methods. Light-mechanical task of weak coupled field is solved by the sequential method. In the first process step the deformation analyses of the reflector is made by the FEM method [2], following by the light analyses. In the second step the beam pattern of the optical system is under evaluation. Searching algorithm has been developed for the lighting field solving on the base of the backward ray tracing algorithm, which analyzes optical system and seeks out optical system elements orienting light rays into the examining parts of the illuminated half-space. Light performance of optical system is qualified as the beam pattern on the plane in the specific distance out of optical midpoint that represents detector. For the coupling between active optical system elements and detector nodes, the finite elements of light beam have been developed as well as the alternative direct computation. For the documentation of above-mentioned process we solved a bilinear optical system consist of a light source, a reflector and a detector. The response of the optical system has been sought (the curve of the illuminance spreading on the detector) on the controlled deformation of the reflector curve. The numerical simulation outcomes has been verified with the experiment measurements of the optical parameters of recall optical system.
References [1] M. Kropáþ, J. Murín, Design and analysis of the automotive headlights. ýasopis pre elektrotechniku a energetiku. 11, 89-92, 2005. [2] ANSYS 8.1 - Theory manual, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
94
Simulation of the ferroelectric hysteresis using a hybrid finite element formulation I. Kurzh¨ofer∗ , J. Schr¨oder∗ , H. Romanowski∗ ∗
Institute of Mechanics, Department of Civil Engineering, University of Duisburg-Essen Universit¨atsstr. 15, 45117 Essen, Germany
[email protected] ABSTRACT
Ferroelectric materials can be found in a wide range of applications in smart materials, e.g. vibration reducing sensors or fuel injection systems. A special characteristic feature of these materials is the appearance of a spontaneous polarization in a certain temperature range. This polarization can be reversed by an applied electric field of sufficient magnitude. The resulting nonlinear material behavior is expressed by characteristic dielectric and butterfly hysteresis loops. These effects are correlated to the structure of the crystal and especially to the axis of the spontaneous polarization. In the present work we present an electric hybrid element formulation where stresses and electric field are derived from constitutive relations. Therefore, we consider the electric displacement as additional degree of freedom, as presented in [1]. Furthermore, the finite element problem is condensed in a manner that the formulation is suitable for conventional boundary problems where the electric field is computed by the negative derivative of the basic field variable φ, used in the finite element approximation. The anisotropic material behavior is modeled within a coordinate-invariant formulation for an assumed transversely isotropic material, see [2] and [3]. The anisotropic response of the material is governed by isotropic tensor functions which depend on a finite set of invariants. The nonlinearities of ferroelectric materials are considered by the regard of internal variables which are governed by evolution equations. The key assumption of this procedure is the split of the strains and the electric displacement into reversible and remanent part. A switching surface is defined and a general mapping algorithm is applied to evaluate the remanent values at the actual timestep. The resulting hysteresis loops for a ferroelectric ceramic which are governed by one part of the Helmholtz free energy are discussed by considering a simple numerical example.
References [1] K. Ghandi & N.W. Hagood, A hybrid finite element model for phase transitions in nonlinear electro-mechanically coupled material. Smart Structures and Materials, Proceedings of SPIE, 3039, 97–112, 1997. [2] J. Schr¨oder & D. Gross, Invariant formulation of the electromechanical enthalpy function of transversely isotropic piezoelectric materials. Archive of Applied Mechanics, 73, 533–552, 2004. [3] H. Romanowski & J. Schr¨oder, Coordinate invariant modeling of the ferroelectric hysteresis within a thermodynamically consistent framework. A mesoscopic approach. Trends in Applications of Mathematics to Mechanics, Wang Y. & Hutter K. (eds.), Shaker Verlag, 419–428, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
95
A Two-Phase Numerical Modelling of the Liquid Solid Transition in Polymer Processing R. Lanrivain†, L. Silva, T. Coupez CEMEF, Ecole des Mines de Paris 1 rue Claude Daunesse, 06904 Sophia Antipolis, FRANCE †
[email protected] ABSTRACT In this paper, we present a two-phase model. It allows the numerical computation, during processing, of a polymer’s mechanical behavior at the liquid state, during the transition, and at the solid state. This work’s context is an industrial project aiming the accurate modelling of the injection molding process [1], [2]. It focuses on the 3D numerical simulation of the different stages encountered in this process : filling, packing, cooling and ejection. During processing, anisotropy of the stress state build-up affects its mechanical, optical or dimensional properties, and induces warpage once the part is ejected. In order to predict residual deformations in the mould, and after ejection, the whole process is simulated with a two-phase thermo-mechanical model, which includes dynamics of phase change. Thus, interactions between polymer in flow and solidified one are implicitly taken into account in the coupled mechanical formulation. Based on the two-phase flow theory [3], a diffuse interface model is derived. A phase field quantifies the presence of each phase at each point of the computational domain. This parameter is obtained by solving an evolution equation of the hyperbolic type, that can be function of temperature or strain. Different behavior laws can be associated to the liquid (like viscous or viscoplastic) and to the solid (like elastic or hyperelastic). So each phase is described by its specifical kinematic variables (velocity for the fluid, displacement for the solidified part). Furthermore, the system of conservation equations (mass and momentum of each phase) is closed by momentum and mass coupling relations (for example, friction type). The kinematics variables for both liquid and solid phase (velocity, liquid pressure, displacement, and solid pressure) are calculated from a single strongly coupled system (monolythic approach) by using the mixed finite elements method within an eulerian framework. Due to the large number of unknowns, parallel computation is obviously required. Validation tests of the model’s implementation are shown, using literature benchmark examples. Results obtained in 3D complex industrial parts underline the robustness and the efficiency of our model.
References [1] T. Coupez,C. Gruau, C. Pequet and J. Bruchon, Metric Map and Anisotropic Mesh Adaptation for Static and Moving Surfaces. The Sixth WCCM, Beijing, China, 2004. [2] L. Silva, R. Valette, and T. Coupez. Viscoelastic compressible modelling of 3d filling and postfilling of complex industrial parts. In V. Brucato, editor, The 6th Int. ESAFORM Conf. Mat. Form., 19-22. University of Salerno, 2003. [3] D.A. Drew, Mathematical modelling of two phase flow. Annu. Rev. Fluid Mech. 15, 261–291, 1983.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
96
A two-phase model for granular flows applied to avalanches Caroline Leppert, Dieter Dinkler Institut f¨ur Statik Technische Univerist¨at Braunschweig, Germany
[email protected] ABSTRACT Understanding of granular materials under rapid motion is of importance to many phenomena in nature and industrial applications. During landslides and avalanches as well as in mixing and storing processes as in silos granular materials undergo phase transitions from solid to fluid state of matter. At rest, the material is characterised by dilatant elasto-plastic behaviour that is rate independent. For low densities and high shear-rates fluid properties dominate. A continuum mechanical approach for dense granular flow including both aspects is presented. Therefore, frictional stresses, representing the rateindependent aspects, extend the viscous stresses using the generalised visco-plastic constitutive model with Coulomb friction as proposed by Chen and Ling [1]. The differentiation between solid and fluid state of matter results from a comparison between current shear stress and plastic yield criterion. The model is able to represent many experimental results for moderately fast granular flows introducing an artificial viscosity that includes internal friction and depends on the current strain rate. To simulate the flow of granular material that travels large distances the material is described by the Navier-Stokes-equations. This requires the formulation of all balance equations for momentum and mass and the constitutive equations using velocity variables. The space-time finite element method is applied to discretise the weak form of balance and constitutive equations. This allows the monolithic coupling between the flowing material and any possible surrounding structure [3]. The method is extended by the level set technique [4] to model the motion of the free surface between granular material and air in order to represent landslides and the complete discharge of silos
References [1] C. Chen and C. Ling, Granular-flow rheology: role of shear-rate number in transition regime, J. Engng. Mech., Vol. 122, 469–480, 1996 [2] S.B. Savage, Analyses of slow high-concentration flows of granular materials. J. Fluid Mech., Vol. 377, 1–26, 1998 [3] B. Hubner ¨ , E. Walhorn and D. Dinkler, A monolithic approach for fluid-structure interaction with space-time finite elements Comp. Meth. Appl. Mech. Eng., Vol. 193/23, 2069–2086, 2004 [4] S. Osher and R. Fedkiw, Level set methods: An overview and some recent results. J. Comp. Phys., Vol. 79, 463–502, 2001
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
97
Parallel 3D Finite Element Analysis of Coupled Problems Lee Margetts *, Ian M. Smith† and Joanna M. Leng* * Manchester Computing, University of Manchester Kilburn Building, Oxford Road, Manchester M13 9PL
[email protected] [email protected] †
School of Mechanical, Aeronautical and Civil Engineering, University of Manchester, P.O. Box 88, Manchester M60 1QD
[email protected]
ABSTRACT Steady advances in computer power have enabled researchers to consider tackling increasingly complex problems. In the academic community, current focus is on multiscale modelling and multiphysics. The aim is for simulation to be more realistically representative of real world processes. This paper considers the simulation of coupled problems involving more than one physical process, multiphysics. In particular, the authors present some ideas and experiences regarding the use of the finite element method and parallel computers to solve 3D coupled problems. In the literature, two main approaches have been used to solve coupled problems. These are sometimes referred to as (i) fully coupled modelling and (ii) un-coupled multi-physics. Both methods have their advantages and disadvantages. In the paper, the authors discuss some of the issues that should be considered when selecting a particular strategy, to ensure computational efficiency. Particular attention is given to an example from the field of magnetohydrodynamics: three dimensional steady state flow in a perfectly insulated rectangular duct. The magnetohydrodynamics example involves solving a system in which both magnetic and hydrodynamic forces influence the behaviour of the fluid. Visualisation of the problem, using streamlines to represent fluid flow (Figure 1) shows that a three dimensional representation is essential to capture the full complexity of the flow. A fully coupled solution strategy is presented in which the full system is represented by a single “stiffness” matrix and solved by a single computer program. A parallel implementation of an element-by-element variant of BiCGStab(l) is used to solve the equations, demonstrating the efficient use of up to 128 processors.
slow
fast
Figure 1 Velocity Streamlines from Three Different Viewpoints Along a Rectangular Duct
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
98
Numerical Simulation of Rubber Curing Process with Application to Bladders Manufacture Paulo Porta † ∗, Carlos Vega† † DARMEX S.A.C.I.F.I. Luis Mar´ıa Drago 1555 – B1852LGS Burzaco – Argentina
[email protected] [email protected] ∗ Corresponding author
ABSTRACT A large number of polymer products are formed into their final shape by polymerization in situ. In particular, mold curing process is the final step in many rubber products manufacturing and determines both the quality of the resulting product as well as productions costs. During this process, important changes in the mechanical properties –e.g. viscosity and modulus– take place, changes which are generally hard to be experimentally characterised. In view of this, a mathematical model is proposed for rubber vulcanisation molding, its strategical value being two fold: from production standpoint, its ability to predict optimal production parameters –the optimal curing time being the most important– and from quality assessment perspective, its capacity of predicting molded part properties. Following the literature –see, e.g. [1]– the mathematical model is built from general mass–energy conservation principles. A series of plausible hypothesis are made in order to simplify the model, which results in a combination of i) the unsteady Fourier’s heat conduction equation –(1)– with a distributed internal heat source, resulting from the reaction –(2), ii) the reaction rate equation –(3)– and iii) closure (γ) constitutive equations, for the kinetic constants of the process, namely KC and tinc : ∂Θ ∂t
= div (k · gradΘ) +
q = Hr dC dt
q ρcp
in Ω for t > 0
dC dt
(γ)
= KC (1 − C)γ
(1) (2)
for t > tinc
(3)
An algorithm is proposed to solve this coupled system. A coupled ODE–implicit in time finite element approximation is proposed and implemented under ALBERTA ([2]). After calibration of the computational model, the complete temperature and cross-links concentration is obtained for the typical bladder geometry. Performance results as well as a short discussion on error estimator behaviour are also presented.
References [1] In-Su Han and Chang-Bock Chung and Hyoeng-Gwan Jeong and Sung-Ju Kang and Seung-Jai Kim, Optimal cure steps for product quality in a tire curing process. Journal of Applied Polymer Science, 74, 2063–2071, 1999. [2] Schmidt, A. and Siebert, K., Design of adaptive finite element software, Springer, Berlin, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
99
Coupled Finite Element Analysis of Composite Laser Rods Thermal Characteristics under Longitudinal Diode Pumping E. Stupak*, R. Kaþianauskas*, A. S. Dementjev†, A. Jovaiša† *Department of Strength of Materials, Vilnius Gediminas Technical University, Saulơtekio av. 11, LT10223, Vilnius-40, Lithuania
[email protected],
[email protected] †
Nonlinear Optics and Spectroscopy Laboratory, Institute of Physics, Savanoriǐ av. 231, LT02300, Vilnius, Lithuania
[email protected],
[email protected]
ABSTRACT Diode laser pumped solid-state lasers are covering a wide range of applications. The longitudinal pumping geometry of laser rod is particularly favorable as it provides a high degree of spatial overlap between pump and lasing modes. However, high pump-power densities are required to achieve sufficient inversion in the laser material. This produces high thermal loading in laser crystals, which, in turn, leads to undesirable thermal effects, such as temperature-dependent index change, temperature-dependent stresses, and end-surface deformation. All those effects are qualified as thermal lensing in laser material. Yttrium aluminum garnet (YAG) crystals doped with Nd, Er, Yb and other ions are currently the most popular laser crystals for diode laser pumped solid-state lasers, especially in end-pumped configurations, that is why laser rods with YAG host material are chosen as the objects of modelling. A multiphysics approach and finite-element method are used to the numerical simulation of thermal lensing in such rods. Thermo-mechanical behavior is considered by applying the ANSYS software, while particular pre-processor for generation of the heat source as well as postprocessor for evaluation of the optical path difference (OPD) is developed. The difference between standard crystal blocks and composite structures with undoped end caps is investigated. The results show that OPD for one pass through the crystal in all cases is practically the same. Thus, the composite rod geometry does not reduce significantly thermal lensing, however temperature gradients are considerable smaller. The obtained results also show that the use of the composite AE practically does not decrease the thermally induced aberrations of spherical type. Therefore, the quality of the probe or laser beam will change mainly in the same way in both the conventional and the composite AE pumped with Gaussian beams.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
100
On the Modeling of Nonplanar Shear Walls in Shear Wall - Frame Building Structures Tolga Akis1, Turgut Tokdemir2, Cetin Yilmaz3 1 Department of Civil Engineering Atılım University, Ankara, øncek 06836, Turkey
[email protected] 2 Department of Engineering Sciences Middle East Technical University, Ankara 06531, Turkey
[email protected] 3
Department of Civil Engineering Middle East Technical University, Ankara 06531, Turkey
[email protected]
ABSTRACT The objective of this study is to model the non-planar shear walls of asymmetric shear wall-frame building structures in elastic range. The modeling work is based on open and closed sections shear wall assemblies for which two different three-dimensional models are developed and verified in comparison to common shear wall modeling techniques. Two-dimensional modeling of symmetric building structures having planar shear walls may be a practical method. However, especially for an asymmetric shear wall-frame building system that contains non-planar shear wall assemblies, the structural system should be modeled in three dimensions. In addition, the three dimensional behavior of the shear wall assemblies should also be taken into consideration. The proposed models are based on conventional wide column analogy, in which a planar shear wall is replaced by an idealized frame structure consisting of a column and rigid beams located at floor levels. For open section shear walls, the connections of the rigid beams are released against torsion in the model. For modeling closed section shear walls, in addition to this the torsional stiffness of the wide columns are adjusted by using a series of equations. In the modeling studies, the rigid diaphragm floor assumption is also taken into consideration. As an example, plan view of an open section U shaped shear wall assembly and the corresponding model is given in Fig. 1. The main goals of the models that are given in this study are to reduce the required time and capacity for the threedimensional analysis of shear wall-frame building systems. In the verification studies, two single shear wall assemblies (an open and a closed section) and a six storey shear wall-frame building system are considered. Static lateral load analysis and dynamic analysis are performed on these structures where the proposed models are used. The results of these analyses are compared with the results obtained by using common shear wall modeling techniques and it is observed that both results agree well with each other.
Figure 1. U-Shaped Shear Wall Section and Proposed Model
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
101
Directional Drillstring Dynamics Fredy Coral Alamo∗ , Hans Ingo Weber∗ and Harry Saavedra Espinoza† ∗ Pontif´ıcia Universidade Cat´olica do Rio de Janeiro Rua Marquˆes de S˜ao Vicente 225, 22453-900, Rio de Janeiro - RJ - Brazil {fjcoral,hans}@mec.puc-rio.br † Universidad Nacional de Ingenieria
Av. Tupac Amaru S/N, Lima - Peru
[email protected]
ABSTRACT A rotating rod under load may execute vibration in different ways: transversal (bending), longitudinal (axial), torsional, or a combination of any of those. In this article, the dynamics of a rotating directional drilling system, constrained to rotate in a borehole, is investigated using the finite element formulation. To study the behavior of the system, a rotating 3D Cosserat rod element is used, this is a newly non linear element developed in this work. The equations of coupled bending, axial and torsional motion of the rotating elastic rod element is derived using the Cosserat rod theory. In general, for slender structures, the shear deformation can be neglected, consequently, to model the drillstring the Bernoulli hypothesis is considered and the shear deformations are neglected. The finite rod element developed has 12 degrees of freedom and takes into account all the geometric nonlinearities. Explicit expressions for the element mass, gyroscopic, stiffness, and non linear terms are derived using Hamiltons principle. Moreover, the finite element discretization is employed and numerical solutions are obtained for the nonlinear drillstring dynamics. Overall, the Cosserat model provides an accurate way of modelling long slender rods.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
102
MVM Energy Method for Buckling Analysis of Tapered Plates M. M. Alinia1, A. R. Rahai2, and S. Kazemi1 1,2
Amirkabir University of Technology 424 Hafez Ave. Tehran 15875-4413, Iran {m.alinia, a_rahai}@aut.ac.ir
ABSTRACT Tapered plates are being increasingly used in modern engineering structures. The increasing use is due to the distributed flexural stiffness that helps reduce the weight of structural elements and improve the utilization of the material. The flexural stiffness, vibrational, and buckling capacities of these plates may be significantly increased by appropriate tapering. On the other hand, provision of openings in perforated plates which provide access for inspection, services, and maintenance, can greatly enhance the applicability of these members in many structures such as platforms, naval and aeronautical structures. Beside these advantages, openings result in a reduction of the buckling capacity, which should be taken into account. n this paper a new exact solution procedure using energy method based on modified vibrational mode shapes is formulated for the buckling analysis of simply supported rectangular plates of abruptly varying stiffness subjected to uniform edge stresses. It is shown that the vibrational mode shapes of a tapered plate is in fact a linear combination of various mode shapes of intact plates. This phenomenon is used to estimate the vibrational mode shapes of taper plates, and is then incorporated to evaluate the buckling loads.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
103
Considerations on Advanced Analysis of Steel Portal Frames Arthur R. Alvarenga and Ricardo A. M. Silveira Department. of Civil Engineering of School of Mines – Federal University of Ouro Preto – UFOP Campus Universitário, Morro do Cruzeiro, s/n, 35400-000 Ouro Preto – MG – Brazil
[email protected],
[email protected]
ABSTRACT This paper presents a little study about the necessary steps to qualify a second- order inelastic analysis as advanced one. Plastic-zone approach is applied to steel plane frames (portals) and the numerical formulation is based on finite element model of a Bernoulli-Euler beam-column member using the called “slice technique”. This element is set on a Lagrangian updated co-rotational system. The nonlinear problem is solved using Newton-Raphson iterative strategy and a new axial force iterative integration is shown. This process was implemented on a computer program PPLANAV* and the minimum requirements of advanced analysis (initial geometrical imperfections and residual stress) are automatically generated. Two examples show good agreement with other researcher’s answers, but there’s a great elapsed computing time.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
104
A Discrete Element Model For The Fracture Analysis of Reinforced Concrete N. Monteiro Azevedo*, J. V. de Lemos† ,J. R. de Almeida+ * UNL-FCT 2829-516 Monte de Caparica
[email protected] † LNEC 1700-066 Lisboa
[email protected] + UNL-FCT 2829-516 Monte de Caparica
[email protected]
ABSTRACT The Discrete Element Method was initially applied to the analysis of discontinuous media, e.g. in rock mechanics and soil mechanics. Recently the DEM has been used in fracture studies of non-homogeneous continuous media such as concrete and rock. A 2D circular rigid discrete element formulation based on the DEM that has been further developed to model concrete is adopted [1]. To simulate the concrete at the meso-level, random assemblies of particles based on a given sieve analysis have to be generated. The DEM model micro-properties also have to be previously calibrated through uniaxial tension and compression tests. The formulation of a 1D rigid discrete element that interacts with the discrete rigid particles through contact interfaces is presented. The DEM enhanced model with reinforcement capabilities is evaluated in a three point bending [2] and in a four point bending [3] tests experiments of reinforced concrete beams without stirrups. Under flexure loading conditions the model is shown to predict the expected final crack pattern, the crack propagation and the load displacement diagram. Under shear loading conditions the model is shown to predict the size effect behaviour that occurs on beams without stirrups failing under diagonal shear and also the expected crack propagation and final crack patterns.
References [1] N. Monteiro Azevedo, A rigid particle discrete element model for the fracture analysis of plain and reinforced concrete, PhD thesis, Heriot-Watt University, Scotland, 2003. [2] C. Bosco, A. Carpinteri and P. Debenardi, Minimum reinforcement in high strength concrete, Journal of Structural Engineering, 116, 427-437, 1990. [3] Z.P. Bazant and M. T. Kazemi, Size effect on Diagonal shear failure of Beams Without Stirrups, ACI-Structural Journal, 88, 268-276, 1991.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
105
Analytical Criteria for the Evaluation of the Internal Forces at the Elastic and Plastic Limit States of Lozenge and Triangular Cross-Sections António M. Baptista Laboratório Nacional de Engenharia Civil (LNEC) Av. Brasil 101 - 1700-066 Lisboa - Portugal
[email protected]
ABSTRACT The elastic-plastic methods for the design of steel structures have been introduced in some national codes, in Europe and America, for almost half a century. This innovation has resulted from the recognition of these design methods for a better estimation of the ultimate resistance of some types of steel structures. These methods are often based on some hypotheses, such as the formation of plastic hinges in the most stressed cross-sections. The development of these plastic hinges is affected by the interaction between the axial force and the bending moment acting on the cross-section. The interaction criteria between these internal forces depend on the cross-section shape. Therefore, specific analytical criteria are required for each type of cross-sections, and for each combination of bending moments over the two main axis of inertia of the cross section (in the case of bi-axial bending). However, these criteria are not usually available in the design codes or text books for most of the cross-section shapes, especially for those that are less common in steel construction. Even in the case of the most usual cross-sections, the analytical criteria are often defined by means of simplified expressions. In the meanwhile, the use of new shapes is becoming more frequent, due to bold innovative structural solutions conceived by modern architects. This paper presents a set of analytical criteria for the evaluation of the internal forces (axial force and bending moment) in lozenge and triangular steel cross-sections, at their elastic and plastic limit states. They are written in a non-dimensional form, which makes them independent of the cross-sections dimensions and of their width-to-height ratio. These criteria are based on the hypothesis of a full yielding of the cross-sections at their plastic limit state. The material is supposed to present elastic-plastic behaviour without hardening. The effects of eventual shear or torsion deformations on the cross section are supposed to be negligible. These analytical criteria put in evidence the different behaviour of symmetrical and non-symmetrical cross-sections, regarding their axis of bending, at their elastic and plastic limit states. They constitute a basis for the elaboration of more complex analytical criteria, for hollow lozenge and triangular cross-sections, or for rectangular full or hollow cross-sections submitted to axial forces and bi-axial bending. A worked example shows an application of these criteria to the evaluation of the elastic and plastic limit states in a square section submitted to an axial force and bi-axial bending. Another worked example presents the expressions for the evaluation of the maximum eccentricities of an axial force in a triangular section, at its elastic and plastic limit states.
References [1] Ch. Massonnet, M.Save, Calcul Plastique des Constructions. Vol 1 – Structures dépendant d’un Paramètre. Ed. B. Nelissen, 3rd Edition, 1976.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
106
Comparative Study of Aluminum Alloy Plate 2024/7050 Under the Effect of Internal Damping M. Benachour *, A. Hadjoui*, M. Benguediab**, N. Benachour***, F. Hadjoui* *Automatic Laboratory of Tlemcen / Faculty of Engineering Sciences / UABB - Tlemcen BP 230 – Tlemcen 13000 – Algeria {mbenachour_99, hadjoui_ab, hadjoui_fethi}@yahoo.fr ** University of Sidi Bel Abbes / Faculty of Engineering Sciences
[email protected] *** Faculty of Sciences / Physical Department / UABB - Tlemcen
[email protected]
ABSTRACT In the present work we determine the influence of structural damping, of an aluminum alloy on the dynamic behavior of a plate with various boundary conditions. Structural damping (loss factor energy) is a very significant parameter by its influence on the dynamic behavior of the mechanical structures. The material of the studied plate is the aluminum alloy 2024 T3 and 7050 T7351. The behavior vibratory of the plate is studied by the finite element method and a comparative study is presented for theses materials. We present also the influence of the loss factor energy on the variation of the inertance relating to each node and each degree of freedom. In parallel, we study the influence of the geometrical parameters of the structure in the frequency domain. In addition, we identify the excited mode of vibration where a comparative example for steel is presented in order to show the excited mode of vibration. The effect of the internal damping is significant in resonance peak, where the reduction of the vibratory amplitude (inertance) is significant. The increase of the geometrical parameters (thickness, ratio length/width), decreases the vibratory amplitude, and on the other hand shift the peaks of resonance towards the high frequencies. The boundary conditions have a great influence on the rotational inertances in a resonance peak.
References [1] M. I. Friswell, The direct updating of damping and stiffness matrices. AIAA Journal, 36, n° 3, 491-493, March 1998. [2] J. C SNOWDON, Vibration and shock in damped mechanical. John Wiley and Sons Inc, 1968. [3] R. D. Mindlin, H. Deresiewics and Schacknow, Flexural vibrations of rectangular plates. Int. J. Eng. Sc., 07, 99-113, 1969. [4] C.F BEARDS, Structural vibration analysis: modeling, analysis and damping for vibrating structures. Ellis Horwood limited, England 1983. [5] S. SRINIVAD, C. V. RAO and A. K. RAO, An exact analysis for vibration of simply supported homogenous and laminated thick rectangular plates. J. of Sound and Vibration, 12, 187-199, 1970. [6] A. HADJOUI, M. BENACHOUR, Application of the matrix connection to the study of the thick plates. Fourth Mechanical Congress, 13 – 16 April 1999, Mohammadia, Morocco. [7] R. MALY Joseph, A. BENDER Kirsten and C. PENDLETON Scott, Complex stiffness measurement of vibration damped structural elements. International Modal Analysis Conference, IMAC-XVIII, San Antonio, Texas, February 2000.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
107
Nonlinear Analysis of Space Frames António A. Correia*, Francisco B. E. Virtuoso† *
ICIST and Instituto Superior Técnico, DECivil Av. Rovisco Pais, 1049-001 Lisboa, Portugal
[email protected]
†
ICIST and Instituto Superior Técnico, DECivil Av. Rovisco Pais, 1049-001 Lisboa, Portugal
[email protected]
ABSTRACT This work presents a method developed and implemented to consider material and geometrical nonlinearities in the behaviour of space frames. A geometrically nonlinear formulation is developed in which the compatibility and equilibrium relations are established in the structure’s deformed configuration using a co-rotational description of the movement. The use of total lagrangian, updated lagrangian and co-rotational descriptions of the movement is discussed. An exact method is presented to consider three-dimensional finite rotations, which cannot be added like vectors as assumed in geometrically linear analysis. The finite rotations are considered by using Euler’s finite rotation formula. That formulation allows obtaining the correct relationships between the rotational degrees of freedom considering large displacements and rotations. The material nonlinear behaviour considered in this work is due to the use of general nonlinear axial stress-axial strain relationships. Based on these assumptions for the material behaviour, and by using an approximation for the internal forces field throughout the frame element, a material nonlinear formulation for three-dimensional structures is presented. The use of an approximation for the internal forces field instead of the usual approximation for the internal displacements field is discussed. An unusual method of integration over the cross-section is presented, where the integrations are carried out over its perimeter, thus allowing any geometrical polygonal shape for it. In this work, despite large displacements and rotations being allowed, only small deformations are considered. This allows the material and geometrical nonlinearities to be treated in a completely independent way. The incremental and iterative strategies used are discussed. The capabilities of the formulations presented here are exemplified by the analysis of a few benchmark problems.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
108
Investigation of shear wall behavior with composite boundary elements Ali Davaran1, Armin Kashefi and Shahin Nayeri Amiri Department of Civil Engineering, Tabriz University Tabriz, Iran
[email protected] {davaran, sh.nayeri}@tabrizu.ac.ir
ABSTRACT Composite construction in steel and concrete offers significant advantages for use as the primary lateral resistance system in building structures subjected to seismic loading. While composite beam and joist floor system have been common for over a half a century, through the use of over the past decade a substantial amount of researches have been conducted world wide on a wide range of composite lateral resistance systems. The appropriate behavior of composite structures and the economical considerations are resulted in offering a new detail of composite shear wall and evaluation of the behavior of this system. The non-linear static analysis has been used in this research. In the detail which is offered in this research steel plates are used to reinforce the boundary elements of concrete shear wall and these steel plates are connected with shear studs to concrete. The research results show that the behavior of this detail with lateral loading is appropriate and ductility of this system is favorable, but the economical features of this detail must be verified when it is necessary to reduce the size of the boundary elements and it is suggested for further researches
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
109
An investigation on dynamic behavior of shear walls on flexible foundation Dr. Mikail Yousefzadeh Fard1, Shahin Nayeri Amiri2and Armin Kashefi Department of Civil Engineering, University of Islamic Azad Tabriz, Iran {mikail,sh.nayeri}@tabrizu.ac.ir Department of Civil Engineering, Tabriz University Tabriz Iran
[email protected]
ABSTRACT
Nowadays, shear walls are used as efficient structural systems for resisting against external lateral loads such as wind and earthquake loads. Regarding to this fact that the pervious studies on the behavior of shear wall systems were performed without considering the effect of foundation and interaction between soil and structure, it seems necessary to conduct some research in the evaluation of shear walls dynamic behavior rested on flexible foundation and with considering the effect of soilstructure interaction. The linear modeling of a shear wall rested on flexible foundation is conducted which is accompanied with the modeling of soil by Winkler `s springs under foundation. The dynamic behavior of shear wall system is assessed. The results obtained show that depending on types of soils under foundation, the values of displacements are more than displacements when the flexibility of foundation is ignored. Also the internal forces at the base of shear walls and the periods of the first three modes of the structure have significant differences between two cases. In one case the interaction of soil-structure is ignored and on the other one the interaction is considered.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
110
Influence of the morphology of adhesive joining on the mechanical properties of periodic metal hollow-sphere-structures ∗,†, J. Gr´acio∗, † ¨ T. Fiedler∗,†, A. Ochsner ∗ Centre for Mechanical Technology and Automation, University of Aveiro, Aveiro, Portugal † Department of Mechanical Engineering, University of Aveiro, Portugal
tfi
[email protected],
[email protected],
[email protected]
ABSTRACT Hollow-sphere-structures (HSS) originate a new group of cellular materials characterised by a high reproducibility of geometry and therefore mechanical properties. Well-known advantages of cellular materials are a high ability of energy adsorption, good damping, excellent heat insulation and a high specific stiffness. Combination of these properties opens a wide field of potential applications, e.g. automotive, aviation or space-industry. Essential Limiting factors for the utilisation of cellular materials are inconstant material parameters and relatively high production costs. Both factors can be reduced by the application of hollow-sphere-structures. A new powder metallurgy based manufacturing route enables the economic production of metallic hollow spheres of defined geometry. Different joining technologies such as sintering, soldering and adhering can be applied to assemble hollow spheres to interdependent structures. Adhering provides the most economic way of joining and allows for further cost reduction and therefore the expansion of the field of potential applications. Another important advantage it the possible utilisation of the mechanical behaviour and morphology of the adhesive layer as a further design parameter for the optimisation of the structure’s mechanical properties for specific applications. The influence of the morphology and mechanical properties of the adhesive layer is discussed in the scope of this article. Finite element (FE) analysis is performed for periodic structures and the results are compared for different geometries. Two different approaches for adhering are considered: hollow spheres completely embedded in a polymer matrix (syntactic foam) and alternatively, concentration of the adhesive layer in the contact points of the spheres (Partial-HSS). In contrast to earlier approaches (e.g. [1, 2]), the geometry is discretised based on regular hexahedron elements. This approach is much more time-consuming, but important in order to achieve more accurate simulation of nonlinear-behaviour (e.g. plasticity).
References [1] W.S. Sanders and L.J. Gibson, Mechanics of BCC and FCC hollow-sphere foams, Materials Science and Engineering A, 352, 150–161, 2003. [2] S. Gasser, F. Paun, A. Cayzeele and Y. Br´echet, Uniaxial tensile elastic properties of a regular stacking of brazed hollow spheres, Scripta Materialia, 48, 1617–1623, 2003.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
111
Dynamic behaviour of a composite twin girder bridge in a high speed interoperable line Helder Figueiredo*, Rui Calçada†, Raimundo Delgado† *
Faculdade de Engenharia da Universidade do Porto Rua Dr. Roberto Frias, s/n
[email protected]
†
Faculdade de Engenharia da Universidade do Porto Rua Dr. Roberto Frias, s/n
[email protected],
[email protected]
ABSTRACT A high-speed railway system is presently under implementation in Portugal, which will allow the connection of the country with a large European network. At the moment, many countries have already developed their own structural solutions for dealing with the effects of high-speed trains in bridges and a great number of structures have been in operation for several years. These solutions were initially designed for specific train types, thus being checked for the dynamic effects of only a small part of the actual European high speed rail traffic. Recent advances in the understanding of the behaviour of high speed railway bridges have been introduced in the EN 1990-Annex A2 and EN 1991-2, reflecting the work undertaken by the ERRI committee D214. In the case of interoperable lines where the high speed TSI is applicable, this being the case of the future Portuguese high speed network, additional checks for dynamic analysis using High Speed Load Model should be performed. One of the solutions that has proven to be very competitive in France is the composite twin girder bridge. This type of deck is used in continuous schemes, with spans lengths ranging from 40m up to 65m. In this paper the dynamic behaviour of this type of bridge is assessed using as reference a 333m long composite twin girder deck located on the French TGV Nord line. The bridge is continuous over its entire length, comprising 7 intermediate spans of 40m and 2 end spans of 28m and 25m. Dynamic analyses of the bridge were performed for both the European high speed trains and the HSLM load schemes, using various types of FE models of increasing level of detail. The response of the bridge is checked in terms of structural safety (amplification levels and fatigue requirements), deck acceleration and passenger comfort.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
112
A Finite Element Model for Beam to Column Bolted Connections with Semi Rigid Behaviour Foces A.*, Garrido, JA.†, Moreno A.†† *
ETS de Ingenieros Industriales, Universidad de Valladolid Paseo del Cauce, s/n, 47011 Valladolid
[email protected]
†
ETS de Ingenieros Industriales, Universidad de Valladolid Paseo del Cauce, s/n, 47011 Valladolid
[email protected] ††
Escuela Politécnica Superior. Universidade da Coruña. Campus de Esteiro, C/ Mendizábal, s/n, 15403 Ferrol
[email protected]
ABSTRACT Nowadays it is recognized that connections and members of steel frameworks have a semi rigid and nonlinear behaviour. One of the main concerns is how to incorporate the connection characteristics into an analysis. In the present study, beam-to-column bolted end plate connections, widely used because of the economy and simplicity of fabrication and assembly, are investigated for predicting their rotational behaviour (moment-rotation curve) that can be used in the frame analysis. In order to predict the rotational behaviour of this type of connection, a three-dimensional finite element model has been developed by the COSMOS/M® code. The proposed model takes into consideration the interaction between the various components that are comprised in the connection. Thus, the modelling domain includes the beam, end plate, bolts and nuts and the column. The main novelty now presented consists of accounting for the flexibility of the column components in the analysis. The column is modeled using solid elements. Other authors employ shell elements or use a rigid surface representing the column flange. Besides, the analysis incorporates the effects of material nonlinearity, for the plates and bolts, using the elastic-perfecty plastic stress-strain relationship. The results obtained from the finite element analysis are evaluated and verified by comparing the numerically predicted results with those of the corresponding tests carried out. The numerical results are also compared with a simplified theoretical model based on yield line analysis and the stub-tee analogy. The 3D finite element model presented in this study can be used to generalize the rotational behaviour of the end plate connection through more extensive parametric studies in order to take into consideration the connection flexibility and its effect on the performance of steel frames. So, extension of the methodology now presented may involve an improvement in analysis and design procedures of the proposed type of connection according to modern design codes.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
113
Rational strain measures - The implicit corotational method G. Garcea, A. Madeo Dipartimento di Strutture, Universit´a della Calabria, 87030 Arcavacata di Rende (Cosenza), Italy
[email protected],
[email protected] ABSTRACT The nonlinear analysis of slender structures undergoing large displacements–small strains requires a proper description of the kinematic strain– displacement relationship to define a rational strain measure. In particular the strain measure must be unaffected by finite rigid body motions, that is it must be objective. Rational strain measures for structural models are not usually available or are too complex to be used in a FEM context, while the technical models which are usually adopted do not satisfy the requirements for objectivity. A simple method, called implicit corotational, to obtain rational strain measures is proposed. The starting point is the corotational idea [1] which is now, following Biot [2], applied at the continuum level. The body is thought of as subdivided in finite parts, each one with a corotational frame that follows the rigid motion of the part. In the corotational frame a linearized kinematic and a linear strain measure may be used in this way. The strain measures become then more accurate with a reduction in the part size. Furthermore it becomes exact by an appropriate limit process. The final results is a rational strain measure. As the displacement field in the corotational reference is infinitesimal, linearized kinematical models for beams, plates and shells can usefully be employed. Since linearized models are always available even for complex structural models (plates or shells) it is easy to obtain the corresponding rational strain measures using this approach. The correctness of the strain measures obtained for 3D beams and thin plates is clear when they are compared with those available in literature [3, 4]. Numerical analysis are performed using Koiter’s asymptotic approach [5]. In this context, which is particularly sensitive to the exactness of the strain measures , the accuracy of the results can be seen.
References [1] B. Nour-Omid, C.C.Rankin, Finite rotation analysis and consistent linearization using projectors. Computer Methods in Applied Mechanics and Engineering, 93, 353-384, 1991. [2] Maurice A.Biot, Mechanics of Incremental Deformations. J. Wiley & Sons, New-York, 1995. [3] Stuart S.Antman, Nonlinear Problems of Elasticity. Springer-Verlag, New-York, 1995. [4] J.C. Simo, L.Vu-Quoc, A three-dimensional finite-strain rod model. Part II: Computational aspects. Computer Methods in Applied Mechanics and Engineering, 58, 79-116, 1986. [5] W.T.Koiter, On the stability of elastic equilibrium. Thesis, Delft, 1945. English transl. NASA TTF10, 883 (1967) and AFFDL\TR70-25 (1970).
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
114
Discrete and continuous analysis of different cable structures V. Kulbach, J. Idnurm Department of Structural Design Tallinn University of Technology, Ehitajate tee 5, Tallinn, Estonia
[email protected] Department of Transportation Tallinn University of Technology, Ehitajate tee 5, Tallinn, Estonia
[email protected]
ABSTRACT Continuous and discrete analysis of different cable structures is under investigation in our report. In cases of distributed loads the non-linear conditions of equilibrium and equations of deformation compatibility are taken as initial equations [1]. To eliminate the horizontal displacements, the equations of deformation compatibility were used in integrated form; corresponding integrals (du/dx)dx were replaced by respective displacements of supporting structures under action of cable forces. Determination of deflections and inner forces for certain cable structures under action of distributed vertical loads may be carried out by means of exact analysis. A girder-stiffened structure has also an exact solution but in the form of complicated transcendental equations. A simpler, compact solution may be found with a proper approximation of the deflection function in the form of trigonometric dependences. Continuous analysis may be also applied to spatial cable structures in the form of hypar-networks with elliptical contour beam [2]. Suitable approximation of the deflection function with use of Galyorkin procedures brings us to values of the network’s deflection and cable forces very near to exact ones. In discrete analysis of girder-stiffened cable structures, the condition of equilibruim is to be composed for every node and the equation of deformations compatibility for every section of the cable [3]. For every joint on stiffening girder were used equation which consider girder’s node’s deformations, internal force in the hangers and load, which is balanced by the stiffening girder. The load may be by distributed load or concentrated force, and may be applied on any point of girder. Using this equations, and moment equilibrium conditions for girder’s supports, were calculated vertical displacements of cable nodes and displacements of girder nodes. Using iteration can be found such value of cable force, which gives actual displacement for every node. After found cable force, all required parameters can be calculated. Examples of analysis of hypar-network and the bridge for a 6100 m strait crossing are presented in the full text of our paper.
References [1] V. Kulbach, Investigation of prestressed cable structures at Tallinn Technical University, Proc. Estonian Acad. Sci., Eng., 8/2, 68 – 83, 2002. [2] I. Tärno, Effects of contour ellipticity upon structural behaviour of hyparform suspended roofs, Publ. of Royal Institute of Technology, Stockholm, 1998. [3] V. Kulbach, S. Idnurm, J. Idnurm, Discrete and continuous modeling of suspension bridges , Proc. Estonian Acad. Sci., Eng., 8/2, 121 – 133, 2002.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
115
Three-dimensional Vibration Analysis of Crystal Plates via Ritz Method Qian LI∗ and VaiPan IU† ∗ Department of Civil and Environmental Engineering, University of Macau
Macao SAR, PRC
[email protected] †Department of Civil and Environmental Engineering, University of Macau
Macao SAR, PRC
[email protected] ABSTRACT In this paper, three-dimensional vibration of rectangular Y-cut crystal plate has been investigated. The three displacement components of plate are expanded in series of Chebyshev polynomial multiplied by the boundary function R which makes expansions satisfy the essential boundary conditions along the edges. Chebyshev polynomial series are chosen as admissible functions for its two distinct advantages: One is that it is a set of complete and orthogonal series in the interval [−1, 1]; the other is that it includes constant and proportional terms. The constant term can easily express the whole rigid displacement of the body. The proportional term can easily reflect the shear force effect along the thickness of a finite plate. The maximum energy function of a plate is expressed in terms of Chebyshev polynomial series. The eigenvalue matrix for natural vibration frequencies is obtained by Ritz method and then solved by computer program. Example of an infinite plate excited by thickness-shear deformation parallel to one edge is solved and verified by exact solutions. Other examples of four clamped edges and four simply supported edges rectangular Y-cut crystal plates are carried out. The trial plates are of three different edge lengths and two different thicknesses. The first twenty frequencies of natural free vibration are compared with those from a finite element method. It also shows that the results from present method and finite element method have a good agreement. Besides, for the advantage of the constant and proportional terms in Chebyshev polynomial series, convergence study demonstrates the rapid rate and high efficiency. The frequencies monotonically decrease and approach certain values with the increase in the number of terms of admissible functions. Three terms are sufficient for the requirement of expansion in the thickness direction. Finally, the free vibration of clamped square Y-cut crystal is investigated. Due to the three-dimensional expansions, any relative displacements in any points of the plate body of modes can be determined very easily by back substitution of the eigenvalues. The deflected shapes of first eight modes show the flexural and thickness extensional modes explicitly.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
116
A 3D Solid Finite Element for Reinforced Concrete Analysis Allowing Slippage of Reinforcement Georgios Ch. Lykidis, Konstantinos V. Spiliopoulos Institute of Structural Analysis and Aseismic Research Department of Civil Engineering, National Technical University of Athens, Zografou Campus, Athens, 157 73, Greece
[email protected],
[email protected]
ABSTRACT In order to evaluate the safety levels of the design of reinforced concrete structures it is essential to be able to predict their response under any type and level of loading. To this end the finite element method of analysis may be used. For such an analysis to be realistic, one must take into account all aspects of the nonlinear behaviour of reinforced concrete. A simple smeared crack material model for concrete behaviour [1], which is based on experiments and uses the uniaxial compressive concrete strength as the only prerequisite has been used recently by the authors to analyze structures loaded statically and dynamically ([2]). A numerical method that treats crack opening and closure in a unified way and presents no numerical instability has been presented. Steel bars are taken into account using an embedded reinforcement formulation [3] and assuming perfect bond with surrounding concrete. The latter assumption is avoided in the present paper with an additional degree of freedom. A realistic model [4] is used to describe the interface behaviour along a reinforcing bar. Comparative analyses of the model with and without bar slipping are performed for static loading cases. The analyses show that the whole procedure manages to give stable and realistic results. This enhanced, therefore, oneparameter concrete model may be used in the analysis of reinforced concrete structures more effectively.
References [1] M. D. Kotsovos, M. N. Pavlovic, Structural concrete, finite element analysis for limit state design, Thomas Telford, London, 1995. [2] K.V. Spiliopoulos, G. Ch. Lykidis, An efficient three dimensional solid finite element dynamic analysis of reinforced concrete structures, Earthquake Engineering & Structural Dynamics, 35, 137-157, 2006. [3] A. E. Elwi, T. M. Hrudey, “Finite Element Model for Curved Embedded Reinforcement”, ASCE, Journal of Engineering Mechanics, 115, 740-754, 1989. [4] R. Eligehausen, E. P. Popov, & V. V. Bertero, Local bond stress - slip relationships of deformed bars under generalized excitations, Rep. UCB/EERC 83-23, Earthquake Engng, Res. Ctr., University of California, Berkeley, 1983.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
117
Some new results on MITC plate elements Mikko Lyly∗, Jarkko Niiranen†, and Rolf Stenberg† ∗
CSC – Scientific Computing Ltd. P.O. Box 405, 02101 Espoo, Finland mikko.lyly@csc.fi †Institute of Mathematics, Helsinki University of Technology
P.O. Box 1100, 02015 TKK, Finland jarkko.niiranen@tkk.fi, rolf.stenberg@tkk.fi
ABSTRACT The approximation of the deflection for the MITC plate elements [1, 2] is shown to be superconvergent with respect to a special interpolation operator [3]. This property holds in the H 1 -norm and the interpolation operator is closely related to the reduction operator used in the MITC methods. A part of the superconvergence result is, roughly speaking, that the vertex values obtained with the MITC methods are superconvergent. This may be an explanation why these methods have become so popular. By utilizing the superconvergence property a postprocessing method has been introduced [3] in order to improve the accuracy of the approximation for the deflection. The new approximation is a piecewise polynomial of one degree higher than the original one and it is constructed element by element which implies low computational costs. We show various computational results illustrating the superconvergence properties of the original approximation and confirming the improved accuracy of the postprocessed approximation. In the numerical tests both uniform and non-uniform meshes are used and cases with different kinds of boundary conditions are studied.
References [1] K.-J. Bathe, F. Brezzi and M. Fortin, Mixed-interpolated elements for Reissner-Mindlin plates. Int. J. Num. Meths. Eng., 28, 1787–1801, 1989. [2] F. Brezzi, M. Fortin and R. Stenberg, Error analysis of mixed-interpolated elements for ReissnerMindlin plates. Math. Mod. Meth. Appl. Sci., 1, 125–151, 1991. [3] M. Lyly, J. Niiranen and R. Stenberg. Superconvergence and postprocessing of MITC plate elements. Helsinki University of Technology, Institute of Mathematics, Research Reports A 474, January, 2005 (http://math.tkk.fi/reports).
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
118
Nonlinear Analysis of Reinforced Concrete Beams Considering the Slip Between Steel and Concrete. Joaquim Marins Neto*, Aloisio Ernesto Assan† *
Department of Structures, Faculty of Civil Engineering, State University of Campinas Av. Albert Einstein, 951, C.E.P.: 13084-971, P.O.Box 6021,Campinas, SP, Brazil
[email protected]
†
Department of Structures, Faculty of Civil Engineering, State University of Campinas Av. Albert Einstein, 951, C.E.P.: 13084-971, P.O.Box 6021,Campinas, SP, Brazil
[email protected]
ABSTRACT In this work aspects of interaction between steel and concrete, for reinforced concrete structures, with particular interest in the mechanism of slip that occurs in the steel-concrete interface are presented. A nonlinear computational model which considers the bond-slip behavior between reinforcing steel and concrete for the nonlinear analysis of beams subjected to bending is developed. The finite element method is used to predict the behavior of reinforced concrete structures based on the properties of the concrete, the reinforcing steel, and the relationship of the steel-concrete interface. The concept about equivalent uniaxial stress-strain model proposed by [1] is used to describe the nonlinear behavior of reinforced concrete which incorporates tensile cracking at a limiting stress and the strain-softening phenomenon beyond the maximum compressive strength from an incremental load procedure with an iterative approach to obtain an equilibrium position of the structure for each increment. The bond is modeled with interface element (bond-zone element) connecting the steel and concrete elements. The interface element presented by [2] has its stiffness based on the stages of relationship between the local bond stress and the relative slip of the bar, for incremental load process. Several numerical examples comparing results of bending beams are presented.
References [1] D. DARWIN; D. A. W. PECKNOLD, Inelastic model for cyclic biaxial loading of reinforced concrete. Civil Engineering Studies, University of Illinois, Illinois, USA, july, 1974. [2] A. K. DE GROOT; G. M. A. KUSTERS; T. MONNIER, Numerical modeling of bond-slip behavior. Heron, Conc. Mech., Vol. 26, 1981.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
119
Novel semi-analytical methodology to determine model parameters for simple finite element bolt model Joost C.F.N. van Rijn National Aerospace Laboratory NLR P.O. Box 153, 8300 AD Emmeloord, The Netherlands
[email protected]
ABSTRACT Bolted joints are commonly used in aircraft structures to join the various parts. These joints are an important factor in the sizing of the construction, for composite to composite as well as for composite to metal joints, as a larger thickness is normally required in the joint area. Consequently joints have an important bearing on the weight of the structure and the material costs. Moreover the production costs of joining are significant. Aircraft structures are mostly modeled using a shell representation. Bolted joints are incorporated in these models using a simple model that represents the bolt by a beam element that connects to one node in each adherent finite element model. At these particular nodes a point force is exerted on the adherent models that will cause a certain, mesh dependent, deformation. Experimentally determined bolt stiffnesses are available from various sources. A finite element model of a bolted joint should provide the same bolt stiffness; otherwise the distribution of bolt loads will be erroneous especially in a multiple load path situation. The bolt stiffness can be changed by adaptation of the beam area or the moments of inertia. It is necessary to account for the deformation of the adherent mesh in order to obtain the right bolt stiffness. The novel semi-analytical methodology to determine the model parameters for a simple finite element bolt model, presented in this paper, provides for a better correspondence between computed and experimentally determined behavior of a bolted joint. It enhances the finite element representation of a bolt as it explicitly accounts for the local deformation in the finite element representation of the adherents. The influence of variation in mesh density and boundary conditions for the shell representation of the adherents is established through a simple finite element analysis. The influence of variations in material stiffness and adherent thickness for both metal and composite adherents is obtained with the presented methodology. A mathematical foundation is provided for the simple finite element bolt model that also enables a sensitivity analysis. The use of the methodology will be demonstrated as it was used to determined the bolt parameters for a total of 40 different configurations within a detailed model of a flap section The presented methodology was developed within the context of the Sixth Framework EU project Bond Assisted Single Step Assembly (BASSA). The financial contribution of the EU is gratefully acknowledged.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
120
Accounting for Fuselage Instabilities in the Coarse Model of an Aircraft Fuselage by means of a Material Law Wilhelm Rust*, Josef Overberg† *
Fachhochschule Hannover – University of Applied Sciences Ricklinger Stadtweg 120, 30459 Hannover, Germany
[email protected] † CAD-FEM GmbH Schmiedestr. 31, 31303 Burgdorf, Germany
[email protected]
ABSTRACT In the typical dimensioning and evaluation process of an aircraft fuselage nominal stresses were obtained from a linear elastic fuselage or section model (barrel) discretized with finite elements in the coarsest possible way. This model does not account for nonlinearities. However, the stresses are compared with allowable ones obtained from either tests or finite element analyses of cutouts (panels) with fine meshes accounting for contact, material and geometric nonlinearities including stability problems. The results are force-displacement curves ending up in the ultimate load. Divided by related areas nominal allowable stresses are obtained. If in one coarse element the stress exceeds the allowable one the total fuselage section is considered as failing. This method does not account neither for changes of the force fluxes due to reaching the local ultimate load nor for the fact that the onset of buckling locally weakens the structure before failing. Therefore, a method is presented here which transfers the local nonlinear behavior analyzed for the panels with fine meshes to the coarse global model. For that purpose all nonlinear effects on the local force-displacement behavior are introduced to the global model by an elasto-plastic material law. It is shown how the stress-strain curves for shear and compression loading (of different shape) are calculated, how they interact in the yield condition, how the flow rule is chosen and how the hardening rule accounts for different ratios of shear and compression. It is shown that the assumptions work well for the described purpose and that the global system can reach a higher ultimate load compared with the standard method. Possible Extensions and Limits of the method are outlined.
References 1. P. Linde, J. Pleitner, W. Rust, Virtual Testing of Aircraft Fuselage Stiffened Panels. Proceedings of 24th Int. Congr. of the Aeronautical Sciences ICAS 2004 2. W. Rust, P. Linde, Ultimate Load Analyses of Aircraft Fuselage Structures within the Virtual Test Rig, Proceedings of IASS/IACM 2005, 5th International Conference on Computation of Shell & Spatial Structures, Salzburg 2005 3. P. Linde, A. Schulz, W. Rust, Influence of modelling and solution methods on the postbuckling behaviour of stiffened aircraft fuselage panels, to appear in Composite Structures
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
121
Modelling of reinforced materials by a subcycling algorithm J.L. Curiel Sosa∗, D.R.J. Owen†, E.A. de Souza Neto†, N. Petrinic∗ ∗ Department of Engineering Science,University of Oxford
Parks Road, Oxford OX1 3PJ, UK
[email protected] †Civil and Computational Engineering Centre, University of Wales Swansea
Singleton Park, Swansea SA2 8PP, UK
[email protected]
ABSTRACT The high nonlinearity associated to the interface and constituents in reinforced materials -e.g. reinforced concrete- has motivated the development of this subcycling algorithm. The interface modelling and the complex material model used to represent the continuum implies a small critical time step when solving a spatial discretised finite element mesh with an explicit time integrator conditionally stable. Making two subcycles -one for the continuum and the other one for the reinforcement- the smallest critical time step does not rule the other sub cycle. The interface is modeled by transmission conditions including empirically-based bond stress-slip relationship. A set of pullout tests of reinforcing bar embedded in a surrounding continuum to demonstrate the efficiency of the scheme is presented and, then, validated against experimental results from the literature. The attractiveness of this scheme lies in the computational efficiency implied by running reinforcement and continuum at two different velocities of execution and solve the problem of nonlinearity created in the interface of very distinct materials.
References [1] J. L. Curiel Sosa, E. A. de Souza Neto, and D. R. J. Owen. A combined implicit-explicit algorithm in time for non-linear finite element analysis. Commun. Numer. Meth. Engng, 22:63–75, 2006. [2] W. J. T. Daniel. A study of the stability of subcycling algorithms in structural dynamics. Comput. Methods Appl. Mech. Engrg., 156:1–13, 1998. [3] I. W. Farmer. Stress distribution along a resin grouted rock anchor. Int. J. Rock Mech. Min. Sci. Geomech., 12:347–351, 1975. [4] M. O. Neal and T. Belytschko. Explicit-explicit subcycling with non-integer time step ratios for structural dynamic systems. Computer and Structures, 31(6):871–880, 1989.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
122
Limit Analysis of Cable-Tied Structures Konstantinos V. Spiliopoulos, and Theodoros N. Patsios Institute of Structural Analysis & Aseismic Research National Technical University of Athens 9 Iroon Politehniou, Zografou Campus, 157-73, Athens, Greece
[email protected]
ABSTRACT Cables are frequently used to strengthen existing framed structures. They are also the main members that support bridge-decks in cable-stayed bridges. This type of structures may be idealised to consist of beam-type members under pure bending and cabled members under pure tension. In order to get an estimate of the strength of such structures a step by step elasto-plastic analysis must be used. This procedure, however, is time-consuming as it has to follow every single plasticization and any deplasticization that may occur up to collapse. Limit analyses, based on the upper or lower bound theorems of plasticity provide a better alternative. In the present work, a limit analysis procedure, based on the upper bound theorem and leading to a linear programming problem, is followed. Plastic rotation in the form of a plastic hinge at the end of a beam-type member marks the plasticization of the corresponding section when its ultimate moment is exceeded, whereas a plastic extension occurs at one point inside the cabled member when its ultimate axial force is exceeded. The whole approach is formulated within the mesh description of statics which is a generalisation of the force method. This method is known to be the computationally most effective one for linear programming structural problems. The process consists of three distinct parts. The first part deals exclusively with the cabled members of the structure. The influence of their force on the rest of the structure is taken into account by satisfying equilibrium along the shortest path between its two ends. In the second part the indeterminacy of the rest of the structure that now consists of beam-type members is catered for using an existing algorithm, also based on a shortest path technique between two points of a connected planar graph. Cantilevers that follow the shortest path of each load to the ground are used in the third part to satisfy equilibrium with the applied loads. The whole process renders a fully automatic and computationally efficient numerical method to find the limit load of the above-mentioned structures. Two examples of strengthened frames, as well as an example of a cable-stayed bridge are analysed.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
123
Smart Super Elements in Slender Structures Subjected to Wind Raphaël D.J.M. Steenbergen*, Johan Blaauwendraad† *
TU Delft, Faculty of Civil Engineering and Geosciences P.O. Box 5048, NL-2600 GA, Delft, The Netherlands.
[email protected]
† Emeritus professor Structural Mechanics, TU Delft, Faculty of Civil Engineering and Geosciences
[email protected]
ABSTRACT Structural analysis of tall buildings of asymmetric plan and irregular geometry subjected to wind load eventuates in complicated calculus. This is among others the case if parts of the building or stability elements stop at a lower height than the rest. FEM programs are at disposal; however the modeling takes a lot of time and a quick and deeper understanding of the force flow is not provided. In this paper this want is supplied by developing a closed-form super element method for two frequently occurring building types. For two types of a tall building of irregular geometry, an insight-providing closed-form analysis method of combining super elements is presented. The main-structure is subdivided in only two super elements. The super elements are based on closed-form solutions describing the force flow in the stability elements. Within an element no change of floor plan, wall and shaft geometry occurs. A node between elements is only chosen where the properties of the building change. The in-plane stiffnesses of the floors are included and act as distributed coupling springs between the stability elements. For each super element a set of simultaneous differential equations is derived and closed-form solutions are obtained; see [1]. For each super element the stiffness matrix is composed from the homogeneous solution and the load vector is composed from both the particular and the homogeneous solution. Foundation stiffness is accounted for. At each change of geometry (node) a marked disturbance in the moment and shear force diagram is found, attenuating along a number of storeys depending on the ratio of the characteristic length and the length of the building. Closed-form expressions for the influence lengths of these disturbances are obtained. Including the rotational stiffness of the foundation may result in substantial disturbances in the stress state at the base of the building. No disturbance occurs if the ratio of the rotational stiffnesses of wall and shaft equals the ratio of the base moments of wall and shaft for an ideal rigid foundation. Results have been presented in [1]. Because of the use of a very small number of super elements with closed-form solutions, the method contributes to the understanding of the behaviour of the considered tall buildings with a discrete change along the height. In a preliminary design stage a fast analysis can be made without spending much time in modelling. It is shown that the modelling and calculating time of the present method is reduced significantly in comparison with complete finite element analysis and accurate results are obtained.
References [1] R.D.J.M. Steenbergen, Static Analysis of Asymmetric Buildings. Delft University of Technology, Delft, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
124
Nonlinear analysis of space R/C frames with non-uniform torsion Boris Trogrlic, Ante Mihanovic and Zeljana Nikolic University of Split, Faculty of Civil Engineering and Architecture Matice hrvatske 15, 21000 Split, Croatia
[email protected] [email protected] [email protected]
ABSTRACT This paper presents a numerical model of stability and load-bearing capacity of space reinforced concrete (R/C) frame structures taking into account the material and geometric nonlinearity. The developed model describes the behavior of space frames with composite cross sections under a monotonically increasing load, from zero up to the ultimate load, i.e. collapse of the structure. The collapse of the structure occurs due to exceeding the limit load and/or loss of stability of space beams or whole structure. The fibre decomposition procedure is developed to solve material and geometrical nonlinear behaviour of composite cross-section in three-dimensional frames. The filaments in the fibre decomposition model of the cross-section, which describe uniaxial behaviour of materials, are extended over corresponding finite element and create a separate prismatic body discretised by brick finite elements. After mapping of boundary forces on prismatic body, i.e. ‘comparative body’, the capture of non-uniform torsion is applied. The main attention in this approach is concentrated on the evaluation of the torsional stiffness, which are strongly nonlinear. Three integration levels exist: the first along the beam-column finite element, the second over the fibre decomposed cross-section and the third over a prismatic comparative body. Behaviour of the space frames shall be more realistically described in this way, especially flexural, lateral and torsional stability effects. The global procedure includes an incremental-direct iteration step approach. The incremental step model of gravitational load level is applied. Geometrical nonlinearity is assumed by Total Lagrange small displacement formulation. The perfect bond-slip effect between concrete and rebars as well as smeared crack model is assumed. Two examples are studied to verify the accuracy of the program and demonstrate its application in practical engineering.
References [1] B.A. Izzuddin, A.A.F.M. Siyam and D.L. Smith, An efficient beam–column formulation for 3D reinforced concrete frames, Computers and Structures, 80, Issues 7-8, 659-676, 2002. [2] H.-G. Kwak and S.-P. Kim, Nonlinear analysis of RC beams based on moment–curvature relation, Computers and Structures, 80, Issues 7-8, 615-628, 2002.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
125
An FE Analysis of the Stresses in Pultruded GRP Single-Bolt Tension Joints and Their Implications for Joint Design Geoffrey J. Turvey*, Pu Wang† *
Lancaster University Engineering Department, Bailrigg, Lancaster, LA1 4YR, UK
[email protected] † Schlumberger Stonehouse Technology Centre, Stroudwater Industrial Estate, Stonehouse, Gloucestershire, GL10 3SX, UK
[email protected]
ABSTRACT FE (Finite Element) analysis is used to determine stresses on critical planes and around the hole edge in a two-dimensional model of a single-bolt tension joint in pultruded GRP (Glass Reinforced Plastic) plate material. The analysis takes account of bolt – hole clearance and friction at the contact surfaces between the bolt shank and the hole. It is shown that even when the hole clearance is nominally zero (~0.2mm) critical stress distributions, normalized with respect to the far field stress are not invariant but change as the tension increases. Friction between the bolt shank and the hole and the small hole clearance are the principal factors which cause the zone of contact (defined by the angle it subtends at the centre of the bolt) to increase with increasing tension, and produce significant changes in the stress distributions at critical locations. These observations cast doubt on the validity of the simplified method of design, given in the EUROCOMP code [1], for bolted tension joints in pultruded GRP plate material, because the method relies on normalized critical stress distributions remaining unchanged as the tension load applied to the joint increases.
References [1] J.L. Clarke ed, Structural design of polymer composites – EUROCOMP design code and handbook, E. & F.N. Spon, London, 1996
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
126
An Efficient Evaluation of Structural Safety applying Perturbation Techniques José M.G.C.Veiga*, António A. R. Henriques†, Jorge M. Delgado* *
†
Escola Superior de Tecnologia e Gestão - IPVC Viana do Castelo - Portugal
[email protected] and
[email protected]
Laboratório da Tecnologia do Betão e do Comportamento Estrutural Faculdade de Engenharia da Universidade do Porto - Portugal
[email protected]
ABSTRACT The application of probabilistic techniques on structural safety evaluation has suffered a great expansion in the last years. However, one of the main problems in the introduction of these techniques is the long computational time consuming required, particularly when simulation methods as Monte-Carlo method are used, even when sampling reduction techniques are adopted [2]. In this paper is presented an efficient structural reliability method that couples perturbation techniques with the finite element method [1]. This method allows, in one only structural analysis, to evaluate the mean value and the standard deviation of the structural response, by defining previously the probability distribution of problem basic random variables. Consequently a much faster analysis is performed, when compared with the most frequent used methods based on reliability techniques. Considering a structural system, with n structural elements, submitted to a load defined by F·Φ = F·[Φ1, Φ2, …, Φn]; where F is the load intensity and [Φ1, Φ2, …, Φn] is the load distribution vector along the structure. According to the finite element method, the system equilibrium is defined by the following equation: K(u)·U = F·Φ ; where K(u) is the tangent stiffness matrix of the structure, defined as a function of the nodal displacements U and F·Φ is the nodal forces vector (it includes dead loads, live loads, wind, etc.). By applying perturbation techniques to this equation it is possible to quantify the mean structural response and its dispersion, in terms of displacements or forces. Finally comparative examples between the results obtained with this technique and other probabilistic methods are presented, allowing to appraise the potentialities of the proposed method.
References [1] J. Eibl and B. Schmidt-Hurtienne, General outline of a new safety format. New developments in non-linear analysis method, CEB Bulletin d’Information, 229, 33-48, 1991. [2] A. Haldar and S. Mahadevan, Probability, Reliability and Statistical Methods in Engineering Design. John Wiley & Sons, New York, 2000. [3] E. Altus, E. Totry and S. Givli, Optimized functional perturbation method and morphology based effective properties of randomly heterogeneous beams. Int. J. Solids Struct., 42, 2345-2359, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
127
Semi-Analytical Analysis of Super Tall Building Bundled-Tube Structures Gong Yaoqing *, Li Ke *
Civil Engineering School of Henan Polytechnic University, Henan Jiaozuo, 454000, China
[email protected]
ABSTRACT A new semi-analytical method is developed for the analysis of interactions between the subgrade and the foundation and the superstructure of the super tall building bundled-tube structure by threedimensional model which is a combination of stiffened-thin-wall tubes on semi-infinite elastic body. The subgrade is idealized as a semi-infinite elastic body, and the rigidities of the elastic body pertinent to various deformations of the foundation have been expressed as analytical equations [1], with which the reactions between the foundation and subgrade can be quantified expediently. The foundation is taken as a part of the superstructure. In fact, the foundation is the extension of the superstructure toward the underground. The only difference is the size, since in most cases the foundation must be large enough to make the soil stable. The superstructure and its foundation of the super tall building bundled-tube structure are simplified equivalently and continuously to a combination of stiffened-thin-wall tubes on semiinfinite elastic subgrade. Then discretization is made by some nodal lines, the unknown functions defined on the lines are used as primary unknowns, and interpolating functions are implemented between the lines. So the displacement field of the computing model can be expressed by the unknown functions. After using the principle of minimum potential energy, the governing equations will then be obtained, which is actually a group of ordinary differential equations. Therefore, analysis of a tall building structure will be changed into the solution of the boundary problem of a group of ordinary differential equations that can be solved by the precise and powerful Ordinary Differential Equation Solver—COLSYS [2] , a kind of computational software. The interactions between the subgrade and the foundation and the superstructure of a super tall building bundled-tube structure due to static loadings are analyzed by the method based on the model. The numerical results show that the analytical model is reasonable and feasible. Therefore, a practicable method for the global analysis of the super tall building bundled-tube structure is obtained, and some valuable conclusions are acquired through analyzing the computing results as well.
References [1] Gong Yaoqing, Tall Building Structures on Elastic Subgrade and Research of Semi-Analytical Method [D]. Beijing: Tsinghua University, 1999 (in Chinese). [2] Yuan Si, Introduction of a common compute program for boundary problems of ordinary differential equation—COLSYS [J]. Computational Mechanics and Application, 2, 104-105, 1990 (in Chinese).
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
128
Large Displacements in Nonlinear Numerical Analyses for Cable Structures Nikolina Zivaljic *, Ante Mihanovic †, Boris Trogrlic † *
Faculty of Civil Engineering and Architecture, University of Split Matice hrvatske 15, 21 000 Split, Croatia Nikolina.Zivaljic@ gradst.hr
†
Faculty of Civil Engineering and Architecture, University of Split Matice hrvatske 15, 21 000 Split, Croatia
[email protected] Boris.Trogrlic@ gradst.hr
ABSTRACT Method for defining appropriate form of prestressed, tensile cable structures and for calculating stress and displacements for such structures is presented. The developed numerical model is taking into account the material and geometric nonlinearity. The described model represents a practical way of implementing the large displacements theory in the analysis of finding appropriate form of prestressed cable structures. The behavior of the structure under an increasing load, from zero up to final is described. The load usually applied in two phases. The first phase can be prestressing. In the second phase, the structure is computed taking into account the dead and the live gravity load. An approach to solving the problem of large displacements in the theory of structures is presented, based on an incremental approach of the Total Lagrange formulation with the small displacements. The model is based on the assumption that the FE are linear and small enough and thus tracking of large translational displacements can be approximated by a simple geometrical model. The resulting force, i.e. stress, inside FE are expressed within the large displacements, based on the successive approach of small displacements of each increment, using a singular quasi-tangent stiffness matrix. A solution of renewable of the internal forces and stress and their influence is presented. The renewal of the large translational displacements is based on their vector from increment to increment. The renewal of the geometry configuration is influenced to the renewal of basic stiffness, geometrical stiffness and large displacement stiffness. Spatial discretization of the system is on two-node line elements. The fiber discretization of the cross section is on triangular elements where mechanical properties of each fiber are presented by the V H diagram. The numerical nonlinear material model is based upon nonlinear material properties defined in the form of a uniaxial V H diagram. The developed model was tested on few practical examples. They are compared by the research computations of the other authors.
References [1] Dvornik J, Lazarevic D. Fractals and formfinding – magic with real numbers. International journal for Engineering Modelling 16, 1-11, 2003. [2] Tabarrok B, Qin Z. Nonlinear Analysis of tension structures, Computers and Structures; 45, 973984, 1992.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
129
Mathematical Modeling for Synthesis and Design of Non-orthogonal Worm Gears with a Straight-line Tooth Contact V. Abadjiev*, D. Petrova†, E. Abadjieva† *
Institute of Mechanics, Bulgarian Academy of Science Acad. G. Bonchev Str., block 4, Sofia 1113, Bulgaria
[email protected]
ABSTRACT The development of the different kinds of transmissions in recent decades has pushed the processes related with the construction of electric transmissions when a preliminary given law of motions transformation is realized by applying a suitable electronic control. Created in this period field of mechatronics covers in particular the most of the mentioned mechanisms and its scientific achievements may be applied to them. Independently of the intensive development of this new part of the techniques, the practice shows that when constructing transmissions oriented to transform big powers, the power mechanical transmission have not found their alternatives. This circumstance motivates the researchers in their trials to create new types of mechanical gears and/or to improve the existing ones in order to find out their new exploitation qualities [1]. The presented research aims at defining of an adequate mathematical model and constructing of a computer program for insuring the process of constructive and technological synthesis and of the design of non-orthogonal worm gears of type Wildhaber. This class of hyperbolic gears is synthesized according to the second Olivier’s principle. The mentioned technological characteristic and the specific geometry of the active tooth surfaces of the gear pair allow this type of mechanical gear sets to be applied alike as power transmission as a kinematic one. The mathematical modeling for synthesis of worm gears of type Wildhaber is based on an approach upon “the region of mesh” [2]. Together with the gear pair design the worked out algorithm realizes a control of the quality of meshing in the whole mesh region or in its definite parts. This control consists of: defining of an optimal configuration of the region of mesh, and of suitable dimensions of the active tooth surfaces; a registration and a limitation of the singular points on the meshed tooth surfaces; a choice of a calculated variant of a gear pair with an optimum situation of the contact lines in the of mesh region from a point of view of hydrodynamic lubrication and related with it hydrodynamic loading capacity, etc. The computer program is directed to studying real models in the design process. Patterns having concrete practical applications are illustrated in the paper.
References [1] Litvin F. Gearing Geometry and Applied Theory. PTR Prentice Hall, A Paramount Communication Company, Englewood Eliffs, New Jarsy, 1994 [2] Abadjiev V. Mathematical Modelling for Synthesis of Spatial Gears. Journal of Process Mechanical Engineering. Proc Inst Mech Engrs, Vol. 216, Part E, 31-46, 2002
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
130
Computational modeling of ultrasonically assisted turning Naseer Ahmed*, Alexander V. Mitrofanov†, Vadim V. Silberschmidt††, Vladimir I. Babitsky††† Wolfson School of Mechanical and Manufacturing Engineering, Loughborough University, UK *
[email protected] †
[email protected] ††
[email protected] †††
[email protected]
ABSTRACT Ultrasonically assisted turning (UAT) is an advanced machining technique, where high frequency vibration (frequency f | 20 kHz, amplitude a | 15 Pm) is superimposed on the movement of the cutting tool. Compared to conventional turning (CT), this technique allows significant improvements in processing intractable materials, such as high-strength aerospace alloys, composites and ceramics. Superimposed ultrasonic vibration yields a noticeable decrease in cutting forces, as well as a superior surface finish [1]. The paper presents a three-dimensional thermomechanically-coupled finite element (FE) model of both UAT and CT that was recently developed as an extension of the initial 2D model [2]. The current model enables studies of various 3D effects in turning, such as oblique chip formation, as well as the influence of the tool geometry on process parameters, e.g. cutting forces and stresses generated in the workpiece material. The model allows transient, coupled thermomechanical simulations for elasto-plastic materials with strain-rate sensitivity. Chip shapes and forces acting on the cutting tool are analyzed. Stress, strain and temperature distributions in the cutting zone are studied. The effects of cutting parameters (such as the feed rate) and influence of friction on both UAT and CT are investigated. Numerical results are validated by the experimental tests performed at our in-house UAT prototype.
References [1] Babitsky, V.I., A. Kalashnikov, A. Meadows, and A. Wijesundara, Ultrasonically assisted turning of aviation materials. Journal of Materials Processing Technology, 132, 157-167, 2003. [2] Mitrofanov, A.V., V.I. Babitsky, and V.V. Silberschmidt, Thermomechanical finite element simulations of ultrasonically assisted turning. Computational Material Sciences, 32, 463-471, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
131
Numerical evaluation of bored piles in tropical soils by means of the geotechnical engineering “GEO4” Fine Software Anjos, G.J.M.*, Cunha, R.P.†, Kuklik, P.‡, Miroslav, B.‡ *
Federal University of Pará, Belém, Brazil
[email protected] †
University of Brasília, Brasília, Brazil
[email protected]
‡
Czech Technical University, Prague, Czech Republic
[email protected];
[email protected]
ABSTRACT This paper presents the back-analyses of field loading tests carried out with bored pile and drilled shaft founded in a tropical soil executed in the University of Brasília experimental research site. For this, a numerical simulation was carried via existing commercial application software denominated GEO4. This software computes the load-displacement curve of the pile’s head plus, distribution of normal and shear forces along the pile’s shaft. The Shear behavior of pile-soil interface is described using the elastic-plastic material model with Mohr-Coulomb yield condition. The complete response of any foundations is represented by determination of shaft and toe resistance plus settlement analyses. Hence, this paper focused in the determination of components of resistance (angle friction and cohesion) and settlement (Young Modulus) for this type of foundation, and explains and presents, in details, the software GEO4 from Fine Inc. Ltd. for foundation design. In relation to the cohesion, it was verified the important effect that this parameter have in the determination of shaft resistance. Moreover, few research topics nowadays deal with the determination of this particular parameter for bored piles. The assessment of geotechnical parameter is a vital component of geotechnical design and some formulation are also presented for this evaluation.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
132
Kinematics and force interaction of screw shaft with variable screw course Bahadirov Gayrat Atahanovich*, Bahadirov Kudrat Gayratovich1 *700143,Uzbekistan, Tashkent, Akademgorodok, F.Khodjaev str. 31, Institute of mechanics and seismic stability of structures Uzbek Academy of sciences
[email protected] 1
700100, Uzbekistan, Tashkent, Shahjahan str. 5, Institute of textile and light industry
[email protected]
ABSTRACT The screw shafts with spiral blade are using in practice are not satisfied to modern demands in industry. For effective smoothing of sheet materials’ creases are necessary uniformly and simultaneously to smooth creases by screw blades from middle site toward ends of the shaft. For achieving of this goal the new construction of screw smoothing blade shaft are developed with so property like blade divergence from middle site toward ends of the shaft with variable (increasing) course. In this construction the next step are compiled by previous via multiplying it on the coefficient which taking into account a delay (sliding) of screw blade in direction of rotation axis of smoothing shaft. The laws of rotation movement of blades’ sides and contact surfaces of screw blade of the shaft with processed of sheet material are obtained. The equation of a curve line of a side of the screw blade is investigated and received too. The smoothing speed of creases and the blade’s speed of a rather sheet material is determined, also are determined it normal, tangent and complete acceleration. Radius of curvature of a side of the screw blade of shaft is determined. The mathematical interrelation of step changes of screw blade, velocity of contact site, and radius of curvature are constructed by depending on angle of shaft’s turn. At mechanical processing of sheet materials by taking into account technological demands directions and volume of acted forces are selected. The force interaction of the variable course blade and processed sheet material with taking into account resistance forces of processed material and variety of screw course, friction forces which arising in contact point of a blade’s surfaces and sides, axial forces of reaction of a support of the shaft, angle of ascent and friction of the screw blade are considered. The torque moment necessary for rotation of one blade and whole shaft is obtained in this work. The driving rate of dislocation of a contact point of a sheet material with the blade of the screw shaft are presented as relation of dislocation of a blade’s screw shaft around of an axis to the appropriate moving of a contact point of the blade on an rotation axis. The numerical solutions’ of equations are compiled by universal software MATHCAD for mathematical calculations with different variations of system’s parameters. Graphics allowing consider kinematical process occurring between blades and processed material are developed on the base of the obtained results. Obtained results used at designing of screw shaft with variable step.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
133
Optimal construction of the thermo-elastic actuator J. Barglik1, B. Ulrych2 1 Silesian University of Technology Krasiēskiego 8, 40-019 Katowice, Poland
[email protected] 2
University of West Bohemia Universitní 26, 306 14 Plzeė, Czech Republic
[email protected]
ABSTRACT Electro-mechanical actuators seem to be one of devices which produce mechanical forces as a result of eddy-currents influence. The most optimal of them are electromagnetic actuators constructed as ferromagnetic devices and thermo-elastic actuators constructed as bimetallic or mono-metallic are shown in Fig. 1.
Figure 1: Arrangement of the thermo-elastic actuator and distribution of electromagnetic field: 1– dilatation element, 2 – field coil, 3 – sleeve, 4 – ring, 5 – frame, 6 – body The ferromagnetic cylinder 1,that plays the role of dilatation element, is clamped to non-ferromagnetic ring 4. The ring is pressed in a sleeve 3, which is fixed to frame 5 of the tool machine. A cylindrical coil 2 is replaced between the ring 4 and dilatation element 1. The coil supplied with harmonic current of effective value I ext and frequency f, generates time variable electromagnetic field. Due to consequent induction heating the temperature of dilatation element 1 rapidly rises. As a result of temperature rise element 1 is pushed to the body 6 with a contact force FC. This kind of the actuator is characterized by a relatively big dispersion of magnetic field. The paper deals with analysis of possibilities of construction optimization of the device in order to minimize losses of electromagnetic energy and consequently to increase total efficiency and to match electromagnetic compatibility requirements. The aim is to find the construction of the actuator making possible to use practically all the electromagnetic energy for induction heating of the dilatation element. The task formulated as a weakly- coupled electromagnetic – temperature - heat stress problem is solved by means of FEMbased numerical method. The results for illustrative example are presented and discussed.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
134
Determination of Moment-Curvature Diagrams and Moment-Deflection Curves in Reinforced Concrete Beams M. H. F. M. Barros*, C. Oliveira† * Civil Engineering Department, FCTUC Polo II Pinhal de Marrocos, 3030 Coimbra Portugal
[email protected] † Civil Engineering Department, FCTUC Polo II Pinhal de Marrocos, 3030 Coimbra Portugal
[email protected]
ABSTRACT The purpose of this paper is to establish an automated process in order to swiftly calculate momentcurvature and moment-deflection diagrams. Comparisons can, this way, be established between several compressed concrete behaviour theories. The model is implemented into a mathematical manipulation program. The consideration of concrete tensile stress-strain relations in structural analysis if often neglected, which leads to the consideration of a far different stiffness in analysis. Considering the tensile stress-strain model referred in Bazant et al[1], together with different compressive stress-strain models, a good comparison of the predicted theoretical behaviour of the several models is obtained
References [1] Deformation of Progressively Cracking Reinforced Beams – ZdenƟk P. Bazant and Byung H. OH
[2] – Eurocode 2: Design of Concrete Structures – CEN – European Committee for Standartization
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
135
Numerical simulation of the nanoindentation experiment: sensitivity analysis of the experimental parameters P. Berke∗ and T. J. Massart† Universit´e Libre de Bruxelles Structural and Material Computational Mechanics Department CP 194/5 avenue Roosevelt 50, B-1050 BRUSSELS (Belgium) ∗
[email protected] †
[email protected]
ABSTRACT The use of certain metallic materials in micro-mechanical systems applications is promising for chirurgical applications because of their bio-compatibility and interesting mechanical and wear properties compared to the widely used silicon. The reliability of miniaturized components, the building blocks of such systems depends largely upon the reliability of the techniques applied to characterize the materials, in relation with numerical simulations. Nanoindentation is the method adapted to investigate the local mechanical properties of materials at the nanoscale. The inter-disciplinary nature of such an experiment makes the interpretation of the results difficult. The goal of the research is the use of a relatively simple but flexible computational tool for the simulation of the nanoindentation experiment in order to better understand the physics and the mechanics involved. A finite element code therefore has been developed and used to solve the simulation problem with all the non-linearities involved (finite deformations, plasticity, contact evolution), including isotropic plastic behavior with hardening and an accurate computational contact mechanics feature using the augmented Lagrangian scheme. These tools allow to investigate the most significant sources of dispersion in nanoindentation experiments and their influence. This analysis helps to fix the range of given experimental parameters for which the sensitivity of experimental results is important. The numerical simulation tool allows a parametric study to quantify the effects of some of these experimental conditions, such as the tip geometry and the surface roughness.
References [1] P.Wriggers, Computational Contact Mechanics. John Wiley and Sons Ltd, ISBN 0-471-49680-4, 2002 [2] T.Belytschko, W.Kam Liu, B.Moran, Nonlinear Finite Elements for Continua and Structures. John Wiley and Sons Ltd, ISBN 0-471-98773-5, 2000 [3] J.P.Ponthot, Unified stress update algorithms for the numerical simulation of large deformation elasto-plastic and elasto-viscoplastic processes, Int.J.Plas., 18, 91-126, 2002
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
136
Numerical evaluation of wrinkling stress in sandwich panels Monika Chuda-Kowalska, Andrzej Garstecki and Zbigniew Pozorski Poznan University of Technology ul. Piotrowo 5, 60-965 Poznan
[email protected]
ABSTRACT Sandwich panels have been for years used as structural and cladding elements. Characteristic feature of these structures is that important role is played by temperature actions, creep of the core and local instability of thin faces of the panel [2]. Proper estimation of these phenomena has become a challenging issue because of strong tendency to optimize technical parameters and costs. The aim of the study is numerical analysis of bending of three-layered panels. In the classical approach linear constitutive equations for faces and core materials are assumed. Moreover, identical tension and compression elasticity modules of the core are introduced [1]. For the plate loaded by axial force P and uniform transversal load q, the following differential equilibrium equation is used: Bw IV + Pw′′ + cw = −q , where w denotes deformation form of compressed face and c is a stiffness coefficient of the core treated as a Winkler foundation. The term B represents the bending stiffness of the plate. In practice, wrinkling stress depends on many more factors, neglected in analytical solutions, though observed in experiments [3]. In this paper we use numerical methods and hence we can allow for the loss of face adhesion and anisotropy of the core. The analysis is carried out for various dimensions (span and depth of the panel and face thickness) and for various material parameters. By the way of the parametric analysis, the sensitivity of structural response to variations of dimensional and material parameters will be studied. The range of applicability of classical theoretical models will be discussed basing on numerical examples. The study presented in the paper was inspired by one of the biggest in the world producers of sandwich panels, with the aim to increase safety and economy.
References [1] K. Stamm, H. Witte, Sandwichkonstruktionen. Berechnung, Fertigung, Ausführung (in German). Springer-Verlag, Wien, Austria, 1974. [2] D. W. Sleight, J. T. Wang, Buckling analysis of debonded sandwich panel under compression. NASA Technical Memorandum 4701, Langley Research Center, Hampton, Virginia, 1995. [3] O. T. Thomsen, Y. Frostig, Localized bending effects in sandwich beams: photoelastic investigations versus high-order sandwich theory results. Composite Structures, 37, 97-108, 1997.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
137
Application of FEA as a Predictive Tool in the Corrugated Paperboard Industry
,&RQGH 0$-LPpQH] -0%LHOVD (/LDUWH 0/DVSDODV ,QVWLWXWR7HFQROyJLFRGH$UDJyQ0DWHULDOV'HSDUWPHQW &0DUtDGH/XQD =DUDJR]D63$,1 PDMLPHQH]#LWDHV $%675$&7
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
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
138
Implementation of 3D homogenization techniques for the thermo-elastic FEM analysis of brazed plate-fin heat exchangers J. Dib†,*, F. Bilteryst* , J.L. Batoz* , I. Lewon† † Nordon-Cryogenie 25 bis, rue du Fort, BP 87 88194 Golbey, France
[email protected]
* ERMeP Institut Supérieur d’Ingénierie de la Conception (GIP-InSIC) 27 rue d’Hellieule, 88100 Saint-Dié-des-Vosges, France
[email protected]
ABSTRACT The present study results from a research collaboration between Laboratory ERMeP (GIP-InSIC) and the company Nordon-Cryogenie (Vosges, France), one of the major world manufacturers of heat exchangers for cryogenic processes. A general description of a multi-stream brazed aluminium plate-fin heat exchanger is presented in Fig 1. The problem for Nordon Cryogénie is to guarantee a thermal performance as well as the safety of the heat exchanger by ensuring the structural integrity of each stream subjected to pressure and temperature gradients. The current research program consists in the development of a dedicated FEM solver for the global thermo-elastic analysis of an exchanger. Since a complete FEM model would lead to several millions of structural elements (solid, shell) we propose a simplified 3D FEM model based on homogeneization techniques to obtain the equivalent (effective) stress-strain relations and equivalent thermal load vectors of the corrugated fins brazed with the plate layers (Fig. 1). Two approaches are considered (kinematical and mechanical models) while considering periodicity. The implementation of these two methods is performed using the free finite element software Code_Aster.
Dib J., Bilteryst F., Batoz J.-L., Lewon I. : Application des techniques d’homogénéisation pour l’analyse tridimensionnelle d’échangeurs de chaleur à plaques et ondes. Actes du 7ème Colloque National en Calcul des Structures, Giens 2005, Vol.1, 417-422, Lavoisier, France, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
139
Hierarchical treecode for optimized collision checking in DEM simulations – application on electrophotographic toner simulations Rainer Hoffmann* *
Océ Printing Systems Siemensallee 2, 85581 Poing, Germany
[email protected]
ABSTRACT Discrete element modelling (DEM) according to Cundall and Strack [1] of a large set of particles with long-ranging forces like gravitation or electrostatics has the disadvantage of a computation time dependence on the number of particles of O(N²). This can be overcome by the usage of a hierarchical tree code [2] which groups particles which are far away to virtual pseudoparticles. This reduces the number of force calculations so that the computation time dependence can be reduced to O(N log N). The criterion which determines a possible grouping of particles is the theta parameter which is a measure for the reciprocal distance of the particle of interest to the neighboring particles. The paper here shows that the tree algorithm can be also used for an efficient collision checking routine since particles that the algorithm determines to be far enough from the particle of interest can certainly be excluded for a collision checking. It is shown, however, that for a particle set with a uniform radius distribution an upper limit for the theta parameter exists. When this upper limit is exceeded collisions will be suppressed or artificial collisions will occur so that the simulation result is severely falsified. This limit can be overcome by extending the theta parameter to include the radius of the particle of interest. This allows the theta parameter to be increased significantly over the previously found limit, thus reducing the computation time by a further 30 % without introducing much additional error. The prerequisite for such a high theta parameter is that the simulated particle set is rather densely packed (packing density > 10%) so that the total behaviour is dominated by collisions not by the long-ranging forces. The algorithm is applied to the simulation of electrostatically charged toner particles used for the electrophotographic print process. To provide a test case for the simulation a simple transfer experiment is chosen: A roller covered thickly with charged toner is positioned next to a second roller with a thin air gap between them. An external voltage is applied to the rollers causing the particles to jump to the second roller. The results of this experiment can be easily measured and the comparison with the simulation shows an error below 5%.
References [1] P. Cundall and O. Strack. A discrete numerical model for granular assemblies. Geotechnique, 29, 47-65, 1979 [2] Joshua Barnes and Piet Hut. A hierarchical o(n log n) force calculation algorithm. Nature, 324, 1986
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
140
3D FEM analysis of basic process parameters in rotary piercing mill *
†
Jan Kazanecki , Zbigniew Pater , Jarosław Bartnicki *
†
AGH University of Science and Technology, al. Mickiewicza 30, 30-059 Cracow, Poland
[email protected] †
Department of Computer Modelling and Technology of Metal Forming, The Lublin University of Technology, 36,Nadbystrzycka, 20-618 Lublin, Poland
[email protected] [email protected]
ABSTRACT In this paper the 3D FEM analysis of basic process parameters in rotary piercing mill is presented. In this process the material is formed by means of two skew rolls, two Diescher’s discs and a plug. The material is dragged by the rolls, it moves axially forward and rotates. The FEM analyze of the rotary piercing process was made under the conditions of 3D state of strain with taking into consideration the thermal phenomena. The calculations were made by means of commercial software MSC.SuperFORM2004 with application of different rolls’ skew angles, different plug designs and working positions. All the mentioned above variants were calculated at a different area reduction ratio. In the result, the progression of shapes, temperature and distributions of stress and strain in various sections of the analyzed tubes were characterized. The numerical results of calculations were justified during the stand test with the use of 100Cr6 steel. The comparisons of the numerical and experimental tests confirm good agreement between the obtained results.
References [1] J. Kazanecki: The seamless tube manufacturing, AGH Kraków 2003, p. 1-622 [2] Z.Malinowski, J. Kazanecki, S. Urba ski: Thermal – mechanical model of tube elongation process in Diescher’s mill, Journal of Material Processing Technology 60, 1996, p. 513-516
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
141
1XPHULFDO(YDOXDWLRQRIWKH,QIOXHQFHRI6WLIIHQHU5LQJVRQWKH&ULWLFDO %XFNOLQJ3UHVVXUHRIWKH9HVVHOV
05.KRVKUDYDQ -6KDKLPHKU
8QLYHUVLW\RI7DEUL]'HSDUWPHQWRI0HFKDQLFDO(QJLQHHULQJ 7DEUL],UDQ
UNKRVK#WDEUL]XDFLU MDYDGVKDKLPHKU#\DKRRFRP
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
5HIHUHQFHV
>@$60(%RLOHUDQG3UHVVXUH9HVVHO&RGH6HF9,,,'LY >@39(OLWHVRIWZDUH9HUVLRQ-DQXDU\
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
142
7RSRORJ\RSWLPL]DWLRQDQGIDEULFDWLRQRIPXOWLPDWHULDOGLHOHFWULFVIRU DQWHQQDSHUIRUPDQFHLPSURYHPHQWV
*XOOX.L]LOWDV 6DEDQFL8QLYHUVLW\ )DFXOW\RI1DWXUDO6FLHQFHVDQG(QJLQHHULQJ 2UKDQOL7X]OD,VWDQEXO7XUNH\ JNL]LOWDV#VDEDQFLXQLYHGX
$%675$&7
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
5HIHUHQFHV
>@03%HQGVRH2SWLPDOVKDSHGHVLJQDVDPDWHULDOGLVWULEXWLRQSUREOHP6WUXFWXUDO 2SWLPL]DWLRQ >@7)(LEHUWDQG-/9RODNLV)DVWVSHFWUDOGRPDLQDOJRULWKPIRUK\EULGILQLWHHOHPHQW ERXQGDU\LQWHJUDOPRGHOLQJRIGRXEO\SHULRGLFVWUXFWXUHV,(((0LFURZDYHV$QWHQQDVDQG 3URSDJDWLRQ2FWREHU >@<.RK-:+DOORUDQ*.L]LOWDV'3V\FKRXGDNLVDQG-/9RODNLV7KHUPRSODVWLF*UHHQ 0DFKLQLQJ IRU WH[WXUHG GLHOHFWULF VXEVWUDWH IRU EURDGEDQG PLQLDWXUD DQWHQQD -RXUQDO RI $PHULFDQ &HUDPLF6RFLHW\
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
143
Reduction method independent substructure synthesis Paul J. Klinge VTT (Technical Research Centre of Finland), Industrial Systems P.O.Box 1000, FIN-02044 VTT, Finland
[email protected]
ABSTRACT Today machine manufacturers are increasingly assembling their products from components manufactured by subcontractors. The component manufacturers often have made detailed FE models of their products. If the designer of the new built-up machine could use these models, he would save a lot of work. To utilise the models the companies must have FE programs than can transfer data. Even then there is a risk that all relevant data is not transfered properly. The FE programs may also differ so, that the results calculated with the transfered model are not the same as with the original program. And the combined FE model of the built-up product becomes large, often too large for practical design calculations. A natural solution is to use substructures. The subcontractors can make reduced sized substructures of their products and the designer uses them in his calculations. However, there are various substructure synthesis methods and file formats, so this works only if the companies use the same FE program. Here a new general method to connect substructures is presented. With this method submodels formed with almost any reduction/substructure method and program can be connected. Also a new kind of substructure is presented. It includes not only stiffness and mass but also damping which is not assumed to be proportional to mass and stiffness. Finally a standard file format for the new substucture is proposed.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
144
Discrete Models for the Simulation of Rubber Components Dynamics M. Lancini, A. Magalini, D. Vetturi Università degli Studi di Brescia – Dipartimento di Ingegneria Meccanica via Branze 38, 25123 Brescia, Italy
[email protected]
ABSTRACT This contribution deals with improvements which have been undertaken on a modeling and simulation tool (developed by the authors [1]), aimed to numerically characterize the dynamic behavior of rubber to metal devices (such as: engine mountings, shock absorbers, vibration dampers, etc.). The adopted approach allows designing such devices in a CAD like environment, meshing them and simulating their dynamics; materials constitutive equations modeling is operated by a neural network, working directly on numerical data supplied by experimentation [2]. The peculiar properties of rubber, in terms of non-linearity, visco-elasticity as well as frequency, temperature and static strain dependence [3], are taken into account in the numerical analysis. The proposed method avoids the implementation of finite elements models (as proposed by many authors [4]) in order to produce a light and easy-to-use modeling and simulation tool, to be adopted by industrial technicians in the design optimization of the mentioned devices. To achieve this point, discrete models, constructed by a multi-body particle based approach, are applied. Several models of such a kind have been taken into account during this research project, from discrete concentrated parameters models [1] to a chosen hybrid particle based model, where local finite elements stiffness is computed directly by the continuum constitutive equations. Simulative results are successfully compared with experimental data for some existing devices, provided by CF Gomma S.p.A.
Acknowledgements The authors are grateful to CF Gomma S.p.A. (Passirano, Brescia, ITALY) for funding and supporting this research.
References [1] A. Magalini, D. Vetturi, Concentrated parameters modeling for the numerical simulation of the mechanical behaviour of rubber to metal vibration dampers. Adaptive Modeling and Simulation, N. E. Wiberg and P.Diéz Editors, International Center for Numerical Methods in Engineering (CIMNE), Barcelona, Spain, 2003 [2] G. Ramorino, D. Vetturi, D. Cambiaghi, A. Pegoretti, T. Riccò, Developments in dynamic testing of rubber compounds: assessment of non-linear effects. Journal of Polymer Testing 22, 681-687, 2003 [3] A. R. Payne, R.E. Whittaker, Low strain dynamic properties of filled rubbers. Rubber Chemistry and Technology, 44, 340, 1971 [4] D. J. Charlton, J. Yang, K. K. Teh, A review of methods to characterize rubber elastic behaviour for use in finite elements analysis. Rubber Chemistry and Technology, 67, 481-503, 1994
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
145
Contact Analysis of Impeller-Shaft assembly and Reasonably Designing the Amount Interference of Turbocompressors A. H. Liao,
H. W. Zhang,
C. H. Wu
State Key Laboratory of Structural Analysis for Industrial Equipment, Department of Engineering Mechanics, Dalian University of Technology, Dalian 116024,China
[email protected]
ABSTRACT The interference fit between impeller and shaft assembly is one of the most important factors influencing the performance of the turbo unit in the design of turbocompressors. The assembly creates a complicated frictional contact problem the interface of the mating parts when the rotational speed is high. Therefore, stress analysis and suitable amount of interference need to be considered in the structural design. A locomotive-type turbocompressor with 24 blades is used for the present analysis. The FE parametric quadratic programming (PQP) method which was developed based on the parametric variational principle (PVP) is used for the analysis of the stress distribution of 3-D frictional contact problem of impeller-shaft sleeve-shaft, makes it possible to precisely simulate complicated geometrical shapes of impeller and considerably enhances accuracy in computation. The advantages of the parametric programming method as compared with the conventional ones are that the penalty factors can be cancelled and the solutions can be obtained directly without tedious iterative procedures such as general incremental iterative method[1]. The effects of fit tolerance and rotational speed, the displacement and the contact stress on the interference-fitting surfaces are discussed in detail in this paper. A range of friction coefficients in the impeller-shaft sleeve and shaft sleeve-shaft contact interfaces is investigated in order to represent the mechanical behaviors of the structure due to the change of the interface characteristic. To decrease the difficulty of the assembling process and make sure the safety of the working state, the suitable amount of the interference is studied so that the interface can have adequate contact pressure under full load. It is found that nonuniform initial interference value in the structural design would avoid relative displacement generated and ensure uniformity of the contact stress. To assure quality of press-fitting, the amount of interference between the shaft sleeve and shaft by press-fitting should be controlled strictly to avoid the rapid increase of the contact stress. The study provides an effective approach which achieves more reliable interference-fitted connections and more precise assembly accuracy with lower manufacturing cost in the structural design.
References
[1] H W Zhang, W X Zhong, Y X Gu. A combined parametric quadratic programming and iteration method for 3D elastic-plastic frictional contact problem analysis. Comput. Meths. Appl. Mech. Engrg, ELSEVIER, 155:307-324, 1998.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
146
Study of the stress induced granular consolidation process by 3D DEM simulation Yong Sheng *, C.J. Lawrence †, B. J. Briscoe † *
†
School of Civil Engineering, University of Leeds, Leeds, LS2 9JT U.K.
[email protected]
Department of Chemical Engineering, Imperial College, London SW7 2AZ U.K. {c.lawrence, b.briscoe}@imperial.ac.uk
ABSTRACT Today’s powder processing technology requires a satisfactory explanation for the evolution of internal structure of powder compacts during the entire consolidation process. Many industries, where processing problems occur, can make use of such an explanation for the process development as well as for their problem solving techniques. Pharmaceutical industry, which tackles with “capping” phenomenon, and, metal and ceramic industries that deal with “near-net shape forming” problems are amongst a few examples of such industries. Many experimental and theoretical studies based on continuum mechanics have been carried out to study the macroscopic mechanical responses of compacts [1]. In recent years, the finite element method has also been adopted in simulations of powder compaction [2]. However in continuum models, the microscopic properties that strongly influence the macroscopic behavior cannot be taken account of. To get optimal mechanical properties of green compacts, better knowledge of the relation between powder characteristics and mechanical behavior of the material during compaction is required. The Discrete Element Method, developed by Cundall and Strack [3], is an effective numerical tool to investigate the micro mechanics of granular materials. In DEM, each individual particle of an assembly is modeled separately and its motion is defined from the interactions with neighboring particles. Then microscopic evolution of the internal stress and the structure of the assembly can be obtained. In the mean time, the macro behavior of the whole assembly can be obtained by statistical sum and average the properties of individual particles. In this paper, a discrete element model, which is capable of modeling friction, cohesion and local plastic deformation at the inter-particle contacts, is used to simulate quasi-static uniaxial compaction of particle assembly. The evolution of microscopic properties of the particle assembly, are presented correlated with the bulk behaviors of the compacts. The relations between particle properties in micro level and macroscopic mechanical properties of the compacts are demonstrated by the comparisons of the numerical results. These results may be further incorporated to an appropriate continuum constitutive model, and used to generate the material parameters of the powder compacts which are sometime very difficult to measure in the experiments.
References [1] Walker,D.M., “An approximate theory for pressure and arching in hoppers”, Chem. Eng. Sci., 21, pp. 975-997, 1966. [2] I. Aydin, B. Briscoe, K. Y.Sanliturk, “The internal form of compacted ceramic components: a comparison of finite element modelling with experiments”, Powder Technology, 89, pp.239254, 1996 [3] P.A. Cundall and O.D.L. Strack., “A discrete numerical model for granular assemblies”, Géotechnique , 29, pp. 47¯65, 1979
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
147
Numerical Analysis of Passive Earth Pressures with Interfaces Jim Shiau and Catherine Smith Faculty of Engineering and Surveying University of Southern Queensland, Toowoomba, QLD, 4350, Australia
[email protected]
ABSTRACT Elasto-plastic analysis for classical lateral earth pressures is presented in this paper by applying the explicit finite difference method using FLAC. The numerical model presented here consists of a rigid elastic structure for the gravity wall, a zero thickness interface for modelling the sliding and separation, and a Mohr-Coulomb soil model for the backfill. The rigid wall was pushed into the backfill soil to induce passive failure and the ultimate load required for the failure is calculated. Numerical results are compared with other available solutions and a number of modelling issues in creating an accurate model are discussed. It is hoped that, through these experience learnt, some numerical pitfalls can be avoided by practicing engineers in their future analysis.
References [1] Shiau, J. S., Lyamin, A. V. and Sloan, S. W. (2003). "Rigorous Solutions of Classical Lateral Earth Pressures" Proceedings of the 6th Australia-New Zealand Young Geotechnical Professionals Conference, pp162-167. [2] Shiau, J. S., Lyamin, A. V. and Sloan, S. W. (2003). "Bearing capacity of a sand layer on clay by finite element limit analysis" Canadian Geotechnical Journal, 40, 900-915. [3] Shiau, J. S., Merifield R. S. , Lyamin A. V. , and Sloan, S. W. (2005). "Undrained stability of footings on slopes." Journal of Geotechnical and Geoenvironmental Engineering, ASCE (Submitted).
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
148
7KUHH'LPHQVLRQDO)LQLWH(OHPHQW$QDO\VLVRID0XOWL3URSSHG'HHS ([FDYDWLRQLQ6KDQJKDL6RIW'HSRVLW
:':DQJ -+:DQJ:36KHQ=+;X:)DQ
(DVW&KLQD$UFKLWHFWXUDO'HVLJQ 5HVHDUFK,QVWLWXWH&R/7' +DQ.RX5RDG6KDQJKDL&+,1$ ZHLGRQJBZDQJ#HFDGLFRP 'HSDUWPHQWRI&LYLO(QJLQHHULQJ6KDQJKDL-LDR7RQJ8QLYHUVLW\ +XD6KDQ5RDG6KDQJKDL&+,1$ ZMKB#KRWPDLOFRP
$%675$&7
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
5HIHUHQFHV
>@ 5 , %RUMD $QDO\VLV RI LQFUHPHQWDO H[FDYDWLRQ EDVHG RQ FULWLFDO VWDWH WKHRU\ -RXUQDO RI *HRWHFKQLFDO(QJLQHHULQJ$6&( >@ 6 + &KHZ . <
@-7&KULVWLDQDQG,+:RQJ(UURUVLQVLPXODWLQJH[FDYDWLRQLQHODVWLFPHGLDE\ILQLWHHOHPHQWV 6RLOVDQG)RXQGDWLRQ >@ % * &ODUN DQG & 3 :URWK $QDO\VLV RI 'XQWRQ JUHHQ UHWDLQLQJ ZDOO EDVHG RQ UHVXOWV RI SUHVVXUHPHWHUWHVWV*HRWHFKQLTXH >@ * : &ORXJK 3 5 :HEHU DQG - /DPRQW 'HVLJQ DQG REVHUYDWLRQ RI D WLHEDFN ZDOO 3URF $6&(6SHFLILF&RQIHUHQFHRQ3HUIRUPDQFHRI(DUWKDQG(DUWK6XSSRUWHG6WUXFWXUH$6&(1HZ
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
149
The computer analysis of the temperature fields arising in bearing node at rotation of a rotor M. Zhuravkov *, S. Bosiakov *, S. Pronckevich † *Belarusian State University [email protected] [email protected] †
Belarusian National Technical University [email protected]
ABSTRACT Thermal calculation for modern high-speed bearings has crucial importance and is reduced to definition of temperature of the bearing, and also those operating conditions of a turbomachine necessary that the temperature in the bearing was kept in allowable limits. It is essential to simplify and lower complexity input of designing bearing nodes of turbomachines in view of the requirements showed to a temperature mode, the computing experiment based on use of engineering packages of the finite-element analysis allows. Authors developed technology of such calculation on the basis of finite-element package LS-DYNA, and computing experiment by definition of a field of temperatures of a rotating rotor arising at friction about the bearing is carried out. As base model the threedimensional model of contact pair the rotor - bearing turbocompressor with rigidly fixed bearing is accepted, between shaft of a rotor and the bearing the contact simulating liquid friction is set. During calculation for different high-speed modes of rotation of a rotor and factors of liquid friction propagations of fields of temperatures, thermoelastic pressure fields and deformations in a rotor and the bearing are obtained, quantitatively described thermoelastic stress-deformed condition of bearing node. The obtained results can be directly used at designing turbocompressors and their modular nodes.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
150
Updating 3D acoustic models with the Constitutive Law Error method. A two-step approach for absorbing material characterization V. Decouvreur*, P. Ladevèze†, Ph. Bouillard* *
Université Libre de Bruxelles, Structural and Material Computational Mechanics, CP 194/5 Roosevelt Av. 50, 1050 Brussels, Belgium [email protected] †
Laboratoire de Mécanique et Technologie, ENS-Cachan Université Paris VI/CNRS, 61 av. Président Wilson, 94235 Cachan, France [email protected]
ABSTRACT In the global framework of improving vibro-acoustic numerical simulations together with the need to diminish the prototyping stages, getting more accurate acoustic models becomes increasingly important for many industries such as automotive companies, for instance. One way to achieve greater accuracy in numerically simulated pressure fields is to make use of parametric updating techniques enabling the tuning of the vibro-acoustic model parameters inside physically meaningful boundaries. The improved model is re-used in the future, allowing more accurate results within reduced simulation times. The updating technique used in this paper is based on the theory of P. Ladevèze [1], and follows from recent works on the constitutive law error method (CLE) applied to acoustics [2]. The updating process focuses on the improvement of the acoustic damping matrix related to the absorbing properties of acoustic materials covering the borders of the acoustic domain. The present part of the paper proposes a 2-step optimization process. It will be shown that this 2-step updating method presents many advantages, especially by diminishing the computation time and allowing the frequency interpolation of the absorbing properties of the materials outside the studied frequency range. While previous works addressed purely numerical setups without experimental data, this study aims at comparing 3D measured pressure fields with numerically updated ones. The test-case is the TRICARMO setup engineered by the LMS company in Leuven, Belgium. The TRICARMO setup is a simplified car cabin with rigid (concrete) walls and car seats inside. Initially roughly described seat material properties are tuned by running the updating simulation process using a library of acoustic absorbing material models.
References [1] P. Ladevèze, A modelling error estimator for dynamic model updating, in: New Advances in Adaptative Computational Methods in Mechanics, Elsevier, 1998, pp. 135–151. [2] V. Decouvreur, Ph. Bouillard, A. Deraemaeker, P. Ladevèze, Updating 2d acoustic models with the constitutive relation error, in: Journal of Sound and Vibration, Vol. 278(4/5), 2004, pp. 773787.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
151
Analysis of Fluid-Structure coupling by Statistical Energy Analysis J.C. García-Andujar*, L. Fritz†, J. López-Díez† * GAMESA Eólica [email protected] †
ETSI Aeronáuticos. Universidad Politécnica de Madrid Plaza del Cardenal Cisneros 3, 28040 Madrid Spain [email protected]
ABSTRACT Fluid-structure interaction has been of high interest during years. A number of different approaches have been developed to estimate the response of structures to acoustic field. The method of analysis fall in two basic categories [1]: conventional and probabilistic. The most popular approach using conventional methods are based in predicting free vibrational modes and then obtain the synthesized forced solution by modal superposition. Within this approach the finite element method also allows direct solution to be calculated. Coupling with a surrounding fluid can be obtained either by BEM or FEM. In the first case, the fluid behavior is formulated by the boundary element method, using the structure as part of the boundary of the fluid field. In the FEM approach, the fluid volume is also studied bay fem, and the coupling with the structural model results obvious. The inconvenient of this approach is the analysis of the response in high frequency ranges. With this approach, both structure and fluid filed can be studied. The probabilistic approach is applied in the cases where a system’s dynamic behavior is not known with sufficient certainty, or the size of the analysis will be to large for a deterministic approach. Statistical Energy Analysis [2] is one of this method and tries to overcome the limitations of the finite element methods. The acoustic problems in building constructions [3] and spacecraft [1] has been successfully studied with this method. SEA presents advantages over the finite element method for studying phenomena in a high frequency band range, but unsteady phenomena require a new formulation; TSEA introduces a new approach to these problems. In the SEA, the vibration loading spectrum is considered to be known. SEA is able to provide estimates of complex system response because its ability to deal with groups of modes on a statistical basis. But in traditional SEA the interest is focused in the response of the structure, and fluid field has no feedback. In the present work, a formulation of SEA considering the fluid as an additional subsystem is presented in order to analyze the problem of fluid-structure interaction. Therefore, response of the structure and the fluid can be studied simultaneously. The presented approach considered the energy flow between the structure and the fluid. The work presents the problem formulation, and then, a plate simply supported inside an acoustic space is solved. Comparison with solution by FEM and FEMBEM are presented, and benefits of SEA in high frequencies range is showed.
References [1] Structural Acoustic Design Manual. ESA PSS-03-204, 1988 [2] R.H. Lyon and G. Maidanik, Statistical Methods in Vibration Analysis. AIAA J., 2, 1015-1024, 1964. [3] R.J.M. Craik, Sound Transmission through Buildings using Statistical Energy Analysis. Ashgate Publishing Ltd, Aldershot england, 1996.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
152
Efficient Iterative Solution of Time-harmonic Scattering by Objects in Layered Fluid Kazufumi Ito*, Jari Toivanen†
* Center for Research in Scientific Computation North Carolina State University Box 8205, Raleigh, NC 27695-8205, USA [email protected] †Department of Mathematical Information Technology, Agora University of Jyv¨askyl¨a FI-40014 Jyv¨askyl¨a, Finland [email protected].fi ABSTRACT We consider the computation of time-harmonic acoustic scattering by sound-soft or elastic objects in layered media. An example of such problem is the scattering by a mine buried in sediment. The computational domain can be tens or hundreds of meters long while the target requires modeling of details smaller than one centimeter. A discretized problem can have several billion degrees of freedom. We decompose the computational domain into far-field and near-field domains and then we perform a finite element discretization. For the vastly larger far-field domain we use an orthogonal mesh and a preconditioner based on a fast direct solver [5]. For the near-field domain a standard preconditioner can be used. The combination of these two defines a preconditioner for the GMRES method. An essential implementation detail is the possibility to reduce the iterations into a small sparse subspace [3, 4]. Due to this the memory usage is essentially reduced and the GMRES method can be used without restarts. For two-dimensional problems this approach has been considered in [2]. A related approach for non elastic targets in three-dimensional domains has been described in [1]. We present numerical results with two-dimensional and three-dimensional problems demonstrating the efficiency of the proposed approach. For example, we show that it is possible to solve problems with more than a billion degrees fo freedom on a modern PC.
References [1] E. Heikkola, T. Rossi, and J. Toivanen, A parallel fictitious domain method for the threedimensional Helmholtz equation, SIAM J. Sci. Comput., 24, 1567–1588, 2003. [2] K. Ito and J. Toivanen, A fast iterative solver for scattering by elastic objects in layered media, Appl. Numer. Math. To appear. [3] K. Ito and J. Toivanen, Preconditioned iterative methods on sparse subspaces, Appl. Math. Letters. To appear. [4] Y. A. Kuznetsov, Numerical methods in subspaces, Vychislitel’nye Processy i Sistemy II, Nauka, Moscow, 265–350, 1985. In Russian. [5] T. Rossi and J. Toivanen, A parallel fast direct solver for block tridiagonal systems with separable matrices of arbitrary dimension, SIAM J. Sci. Comput., 20, 1778–1796, 1999.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
153
Computational Aeroacoustics by Coupling the Finite-Element and the Lattice-Boltzmann-Method Barbara Neuhierl*, Ernst Rank† * Dipl. Ing. Barbara Neuhierl Siemens AG, CT PP 6, Otto-Hahn-Ring 6, D-81730 München [email protected] † Prof. Dr.rer.nat. Ernst Rank Lehrstuhl für Bauinformatik, Technische Universität München, Arcisstr. 21, D-80290 München [email protected]
ABSTRACT Computational aeroacoustics is a relatively young field of engineering. Characteristic application domains are for example the area of aviation and railway, internal flows in pipes or HVAC systems, or even consumer products and household devices, where aerodynamic sound is generated e.g. by fans. Sometimes not only the fluid itself causes sound phenomena, but also vibrations of structures excited by the flow like for example the walls of a pipe or components outside cars, trains or airplanes (mirrors, antennas, pantographs, etc.) lead to further generation of noise. This paper deals with the computation of such fluid-structure coupling effects, considering the interaction of fluid flow, acoustic wave propagation and the structural vibrations of a body lying within or enclosing the flow area. As computational aeroacoustics requires an accurate, time-dependent calculation of pressure and density fluctuations, it was decided to use the lattice-Boltzmann method, a ‘mesoscopic’ formulation based on a strongly simplified kinetic theory nevertheless approximating the Navier-Stokes equations, for the CFD part of the problem. In contrary to “classical CFD”, where a macroscopic model is used by solving the discretized Navier-Stokes equations, the lattice-Boltzmann method enables a time explicit and – as far as our experience goes - less time expensive computation of compressible flows. It is thus well suited for representing acoustic phenomena, allowing to concurrently approximate both flow and acoustic field. On the structural side, the finite element method was applied to represent the structural dynamics, where flow pressures are applied as loads onto surfaces of structures. The vibrations in turn lead to acoustic wave propagation within the fluid. Data (i.e. flow pressure and vibration velocity) is exchanged via interfaces programmed for this special purpose, taking into account typical differences of finite element mesh and CFD grid. In this way, a bi-directional coupling procedure was generated enabling the calculation of aeroacoustic effects in connection with coupling effects that can occur if structure and fluid influence each other mutually. As a suitable model for the verification of computational aeroacoustics as well as coupling effects, the flow around a circular cylinder has been chosen. The occurring effects on the fluid as well as on the structure side are well-known and have been the subject of many experiments and simulations. In the wake of the cylinder, for example, the “v. Kármàn vortex streets” are produced which cause narrow-banded sound, the so-called “Aeolian Tones”. This effect, the structural dynamic vibration excited by the flow, as well as the wave propagation caused by the vibrating body were simulated simultaneously. The application of the method to industrial problems will show the suitability of the approach.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
154
Analysis of a perforated panel for the correction of low frequency resonances in domestic rooms Andrea Panteghini*, Francesco Genna, Edoardo Piana *
Department of Civil Engineering – University of Brescia Via Branze, 38 – 25123 Brescia, Italy {andrea.panteghini,francesco.genna,piana}@ing.unibs.it
ABSTRACT Perforated panels can be used as devices for the selective acoustic correction of rooms. Unlike panels made by porous materials, they work principally at low and middle frequency, and are acoustically inert at high frequency. For this reason, their main application is for the correction of modal resonances of rooms. Perforated panels consist of one layer of porous (dissipative) material and one of air, closed by a perforated plate and placed against a rigid wall. When this device is invested by a sound wave, the inside air resonates at a specific frequency, and a much energy is absorbed near this resonance frequency. Although perforated panels are used at both low and middle frequencies, there seem to be no studies in the literature about their modeling at low frequency, partly because it is very difficult to make experiments in this part of the audio spectrum. In particular, classical literature models, developed thinking to middle frequency behavior [1], [2], [3], do not perform well, in comparison with experimental and numerical results, when applied to study such low frequency devices. Here, we present an analytical and a numerical approach (this last based on the finite element method), developed in [4], for predicting the sound absorption of a perforated absorber system at low frequency. After validating the capabilities offered by the finite element technique, comparisons are made between the results of numerical analyses performed on both complete coupled acousticstructural and simplified models. A new, simple analytical algorithm for the design of these panels, based on the acoustic impedance method, is also presented. Finally, we briefly discuss the results of a method for the experimental measure of the acoustic impedance of perforated panels at low frequency, a method that has never been used to such a purpose, so far, to the best of our knowledge. Our numerical and analytical results are finally compared both with these experimental data and with the results of literature models [1], [2].
References [1] R. H. Bolt, On the design of perforated facing of acoustic materials, Journal of the Acoustical Society of America, 19(5), 917-921, 1947. [2] K. A. Velizhanina, Design calculation of sound absorbers comprising a porous material with a perforated facings, Soviet Physics Acoustics, 14(1), 37-41, 1968. [3] D. Takahashi, A new method for predicting the sound absorption of perforated absorber systems, Applied Acoustics, 51(1), 71-94, 1997. [4] A. Panteghini, Analisi numerica di pannelli per lo smorzamento delle risonanze a bassa frequenza in ambienti di piccole-medie dimensioni, Laurea Thesis (in Italian), Department of Civil Engineering, University of Brescia, Italy, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
155
Sound Insulation Provided by a Multi-layer System Containing a Heterogeneity: a BEM Approach Andreia Pereira*, António Tadeu† Department of Civil Engineering, University of Coimbra Pinhal de Marrocos, Polo II, 3030-290 Coimbra, Portugal [email protected]
*
†
Department of Civil Engineering, University of Coimbra Pinhal de Marrocos, Polo II, 3030-290 Coimbra, Portugal [email protected]
ABSTRACT The sound insulation provided by a multi-layer partition with an infinite plane, composed of sets of fluid and elastic layers, dividing an infinite acoustic medium is analysed in this paper. A circular cylindrical fluid-filled heterogeneity is placed inside one of the elastic layers of the partition and the resulting airborne sound insulation and the impact sound pressure level are calculated. The solution is obtained using a Boundary Element Method (BEM) formulation in the frequency domain, where only the discretization of the heterogeneity’s surface is required, since Green’s functions are used for the multi-layered media. The model is excited by cylindrical line loads placed in either the acoustic or the elastic medium. Material losses are taken into account by means of complex velocities. A similar model has been developed by the authors in previous work, in that case to predict the sound insulation provided by single partitions in the presence of rigid, free, fluid-filled and elastic-filled heterogeneities. It is extended here to handle multi-layer systems. Several simulations are performed to see if the presence of fittings such as pipes, which are often housed inside building partitions, may affect the sound insulation. The analysis assumes multi-layer partitions, such as those built with two elastic layers sandwiching an air gap, and floating systems composed of a concrete screed resting on a cork layer laid over a structural concrete layer. An air-filled heterogeneity is placed inside one of the elastic layers. Responses are compared with those provided by the solution without the presence of the heterogeneity. The analysis allows the conclusion that the sound insulation is slightly affected by the presence of the heterogeneities inside multi-layer systems.
References [1] A. Tadeu and J. António, 2.5D Green functions for elastodynamic problems in layered acoustic and elastic formations, Journal of Computer Modeling in Engineering and Sciences CMES, 2, 477-495, 2002. [2] M. H. Aliabadi, The Boundary Element Method, John Wiley & Sons Ltd, England, 2002. [3] A. Pereira and A. Tadeu, Sound pressure reduction provided by an infinite elastic layer containing heterogeneities via BEM, Proceedings of the 6th congress on Boundary Element Techniques, 193-198, 2005. [4] A. Pereira and A. Tadeu, Sound pressure level differences due to the presence of heterogeneities inside an elastic partition, Proceedings of the 12th International Congress on Sound and Vibration, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
156
An efficient wave based method for steady-state vibro-acoustic transmission calculations B. Pluymers∗, W. Desmet, D. Vandepitte, P. Sas ∗K.U.Leuven, Department of Mechanical Engineering, division PMA
Celestijnenlaan 300B, B-3001 Leuven, Belgium. [email protected] ABSTRACT Most commonly, element based methods like the finite, the infinite and the boundary element method are applied for analyzing steady-state vibro-acoustic problems in unbounded domains. The finite element method and the infinite element method discretize the considered problem domain and approximate the dynamic response variables with approximating shape functions. The boundary element method also applies approximating shape functions, but has the advantage that only the boundary of the considered problem needs to be discretized. Due to the selection of approximating shape functions, the discretization has become more dense with increasing frequency, which restricts the applicability of the element based methods to the lower frequency range. Transmission calculations make out an important class of problems in unbounded domains. An aperture or a structure is positioned in an infinitely large rigid baffle plane, which divides the unbounded space into two semi-infinite subdomains. This allows determination of the transmission characteristics of the considered aperture or structure. Transmission calculations are most commonly performed with the boundary element method and the infinite element method. The wave based method [1] has proven to be an efficient alternative simulation technique for steadystate vibro-acoustic problems. In recent years, both bounded [2] and unbounded [3] problems have been successfully tackled. The wave based method is based on the indirect Trefftz approach, in that the dynamic response variables are expanded in terms of wave functions, which are exact solutions of the underlaying differential equations -contrary to the element based methods where approximating shape functions are applied- such that no fine discretization of the problem domain or its boundary is required. The resulting numerical wave models are much smaller than the element based models and they exhibit an enhanced computational efficiency. These properties allow the wave based method to tackle problems at higher frequencies than the element based methods. In this paper, the wave based method is applied for transmission calculations. In the first part of the paper, the selection of a set of converging wave functions and the subsequent construction of the numerical model are discussed. In a second part, the method is applied to a two-dimensional numerical example and compared to the element based techniques.
References [1] W. Desmet A wave based prediction technique for coupled vibro-acoustic analysis, KULeuven PhD. Thesis 98D12, Leuven (1998). [2] W. Desmet, B. Van Hal, P. Sas, D. Vandepitte, A computationally efficient prediction technique for the steady-state dynamic analysis of coupled vibro-acoustic systems, Advances in Engineering Software, Vol. 33, (2002), 527-540. [3] B. Pluymers, W. Desmet, D. Vandepitte, P. Sas On the use of a wave based prediction technique for steadystate structural-acoustic radiation analysis, Journal of Computer Modeling in Engineering & Sciences (CMES), 7(2), 173-184, (2005).
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
157
Modeling Sound Radiation by Structures Caused by a Ground Impact Load: a BEM Approach Paulo Santos*, António Tadeu* Dep. of Civil Eng., University of Coimbra Pólo II – Pinhal de Marrocos, 3030-290 Coimbra, Portugal [email protected] *
ABSTRACT This paper is part of research work whose the main objectives are to model ground vibration induced by rail traffic on the surface or underground, and to predict the acoustic radiation caused by vibration in building structures, using the Boundary Elements Method (BEM). This paper proposes a BEM formulation which is implemented to model the propagation of waves in an elastic homogeneous halfspace confined by a fluid (air), where the waves are produced by steady state, spatially sinusoidal, harmonic line structure-borne loads at low frequencies. The BEM model is formulated in the frequency domain and fully accounts for the air-solid interaction. The required two-and-a-half-dimension fundamental solution (Green’s functions) and stress functions in Cartesian co-ordinates for the elastic and fluid media can be found in [1]. The BEM integrations are performed analytically for the loaded element [2, 3], whereas a Gaussian quadrature scheme is used when the element to be integrated is not the loaded element. This paper describes the analysis as carried out in the frequency domain, for waves that travel perpendicularly to the z-axis (pure 2D problem). The results show the influence of: the impact source position; the wall material stiffness, and the impact source direction - vertical (y) or horizontal (x). The relationship between the normal vibration velocity of the vibrating structure and the acoustic energy radiated by this same structure (vertical wall) is also analyzed. At this early stage of the research the authors modeled a homogeneous elastic flat half-space, excited by an applied impact line load, and studied the acoustic radiation provided by a simple structure (vertical wall). The future developments will include a railway tunnel and also a more realistic (complex) building structure. Comparison of the numerical results with some experimental data is another future objective.
References [1] A. Tadeu and J. António, 2.5D Green’s functions for elastodynamic problems in layered acoustic and elastic formations. Computer Modeling in Engineering and Sciences, 2(4), 477-495, 2001. [2] A. Tadeu, P. Santos, E. Kausel, Closed-form integration of singular terms for constant, linear and quadratic boundary elements – Part I: SH wave propagation. Eng Anal Boundary Elements, 23(8), 671–681, 1999. [3] A. Tadeu, P. Santos, E. Kausel, Closed-form integration of singular terms for constant, linear and quadratic boundary elements – Part II: SV–P wave propagation. Eng Anal Boundary Elements, 23(9), 757–768, 1999.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
158
Cohesive Model of Electromechanical Fatigue for Ferroelectric Materials and Structures Irene Arias∗, Santiago Serebrinsky, Michael Ortiz Division of Engineering and Applied Science, California Institute of Technology 1200 E. California Blvd, Pasadena, CA 91125, USA [email protected], [email protected] ∗Dep. de Matem`atica Aplicada III, Universitat Polit`ecnica de Catalunya
Jordi Girona 1-3, Barcelona 08034, Spain [email protected] ABSTRACT Ferroelectric materials are extensively used in a variety of sensor and actuator applications, where the non-linear coupling between mechanical and electrical fields are of primary interest. They are also a promising set of materials for improved dynamic as well as non-volatile memory devices, where only the electrical properties are directly exploited. However, ferroelectrics are brittle, and their low fracture toughness (in the order of 1 MPa m1/2 ) makes them susceptible to cracking. In addition, ferroelectric materials exhibit electrical fatigue (loss of switchable polarization) under cyclic electrical loading and, due to the strong electro-mechanical coupling, sometimes mechanical fatigue as well. Conversely, the propagation of fatigue cracks hinders the performance of the devices and raises serious reliability concerns. Despite recent experimental and modelling advances, the precise nature of the interactions between fracture, deformation and defect structures underlying ferroelectric fatigue is in need of further elucidation, and a physics-based multiscale model enabling the prediction of the fatigue life of ferroelectric devices is yet to emerge. Therefore, there remains a need for phenomenological and empirical models that can be experimentally validated and used in engineering design. We present a model of electro-mechanical ferroelectric fatigue based on the postulate of a ferroelectric cohesive law that: couples mechanical displacement and electric-potential discontinuity to mechanical tractions and surface-charge density; and exhibits a monotonic envelope and loading-unloading hysteresis [1]. The model is applicable whenever the changes in properties leading to fatigue are localized in one or more planar-like regions, modelled by the cohesive surfaces. We validate the model against experimental data for a simple test configuration consisting of an infinite slab acted upon by an oscillatory voltage differential across the slab and otherwise stress free. The model captures salient features of the experimental record including: the existence of a threshold nominal field for the onset of fatigue; the dependence of the threshold on the applied-field frequency; the dependence of fatigue life on the amplitude of the nominal field; and the dependence of the coercive field on the size of the component, or size effect. Our results, although not conclusive, indicate that planar-like regions affected by cycling may lead to the observed fatigue in tetragonal PZT.
References [1] I. Arias, S. Serebrinsky, M. Ortiz, A phenomenological cohesive model of ferroelectric fatigue, Acta Materialia, 54, 975–984, 2006.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
159
Simulation of active systems in a NVH full car model H. Atzrodt*, S. Herold , D. Mayer Fraunhofer Institute for Structural Durability and System Reliability, LBF Bartningstr. 47, 64289 Darmstadt, Germany [email protected]
ABSTRACT Vibrations in the higher frequency range in cars can result in disturbing noise and reduction of comfort. An active interface or a force actuator mounted between suspension and chassis can reduce these vibrations. The simulation of the full car model with the active interface or a force actuator is essential for the dimensioning of the active system, development of the controller, testing of the functionality, estimation of the performance and monitoring of the system reliability. An active interface has been developed and is currently improved in the Fraunhofer FASPAS project [1]. With the simulation of the active Interface first experiences can be gathered even before the interface is integrated in the real structure. In this case the force actuator is composed of smart actuators based on piezoceramic materials. The application of a controller should reduce disturbing vibrations. The simulation is a helpful software tool for selection of the smart actuators and for construction of the force actuator. In this paper a NVH full car model based on FEM and MBS will be conducted. The suspen-sion will be designed in the MBS and embedded in the chassis, which is imported with its elastic eigenmodes from the FEM into the MBS. After integration of the active systems [2] into the MBS model, the controller [3] will be imported from Computer Aided Control Engineering (CACE). The potential of the active systems will be examined by means of a complete system simulation of the active NVH full car model.
References [1] T. Melz, M. Matthias, The Fraunhofer MaVo FASPAS for smart systems design for automotive and machine tool engineering. 12th SPIE International Symposium, San Diego, California, 2005. [2] M. Thomaier, H. Atzrodt, S. Herold, M. Mayer, Simulation of a Complete System Using the Example of an Active Interface for Vibration Reduction. Virtual Product Development in Automotive Engineering, Mürzzuschlag, Österrreich, 2004. [3] A. Preumont, Vibration Control of Active Structures - An Introduction 2nd edition. Kluwer Academic Publishers, Dordrecht Boston London, 2002.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
160
Toward an exhaustive modeling of the macroscopic behaviour of shape memory alloys Ferdinando Auricchio∗ , Lorenza Petrini† , Alessandro Reali∗ ∗
Dipartimento di Meccanica Strutturale, Universit`a degli Studi di Pavia Via Ferrata 1, 27100 Pavia (PV), Italy [email protected] [email protected] † Dipartimento
di Ingegneria Strutturale, Politecnico di Milano Piazza Leonardo da Vinci 32, 20133 Milano (MI), Italy [email protected]
ABSTRACT The employment of shape memory alloys (SMA) in a large number of applications in the fields of aeronautical, biomedical and structural engineering constitutes the basis for an increasing interest of researchers in the direction of an exhaustive modeling of their macroscopic behaviour. However, many SMA models present in the literature consider a perfect pseudo-elastic behaviour (i.e. no residual strains), which is proved by experiments to be only an approximation. This work takes its basis from the one-dimensional version of a model proposed by Auricchio et al. [1] which is able to describe main SMA macroscopic effects as pseudo-elasticity and shape-memory effect as well as to include permanent inelasticity and degradation effects. Such a model is here improved with the introduction of an elastic modulus which depends on the reached transformation strain level. Finally, some numerical tests are presented in order to show the good performance of the obtained model.
References [1] F. Auricchio, A. Reali, U. Stefanelli, A three-dimensional model describing stress-induced solid phase transformation with permanent inelasticity. To appear on International Journal of Plasticity, 2006.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
161
Vibration Damping Using Resonant Shunted Shear-Mode Piezoceramics Ayech Benjeddou *, Julie A. Ranger † * Institut Supérieur de Mécanique de Paris 3 rue Fernand Hainault, 93407 Saint Ouen CEDEX, France [email protected] †
Institut Supérieur de Mécanique de Paris 3 rue Fernand Hainault, 93407 Saint Ouen CEDEX, France [email protected]
ABSTRACT Vibration damping using shunted piezoceramics was the focus of many researches, in particular during the last decade, as attested by the frequent surveys [1-3]. Most investigations have concerned the classical transverse-mode of piezoceramics which uses the material electromechanical coupling coefficient (EMCC) k31. However, the longitudinal-mode, exploiting the highest EMCC k33, has been much less investigated. Both modes provide the so-called Extension Shunted Damping (ESD) [4]. The shear-mode, which uses the EMCC k15 with a value very close to k33, has been studied only recently [5]. It has been shown that it provides the so-called Shear Shunted Damping (SSD). The ESD has been investigated with resistive, resonant or capacitive shunts; while the SSD has been evaluated only with a resistive shunt. It is then the objective of this proposal to present, for the first time, the theoretical formulation and finite element investigation of the use of the shear-mode piezoceramics for resonant shunted vibration damping. Preliminary results for the first two modes of a vibrating aluminium beam with sandwiched (axially polarized) piezoceramic patches indicate that, unlike ESD, resonant shunting does not enhance much the SSD compared to the resistive shunting. Moreover, it is found that resistive SSD is almost as efficient as a resonant ESD. The latter result is very interesting since the resistive shunting is easier to implement (no tuning and no huge unphysical inductance) than the resonant one.
References [1] G. A. Lesieutre, Vibration damping and control using shunted piezoelectric materials. The Shock and Vibration Digest, 30, 187-195, 1998. [2] M. Ahmadian and A. P. DeGuilio, Recent advances in the use of piezoceramics for vibration suppression, The Shock and Vibration Digest, 33, 15-22, 2001. [3] S. O. R. Moheimani, A survey of recent innovations in vibration damping and control using shunted piezoelectric transducers, IEEE Transactions on Control Systems Technology, 11, 482494, 2003. [4] A. Benjeddou, J.-A. Ranger, Simple finite element modelling and performance evaluation of passive vibration damping using shunted piezoceramics. In First International Congress on Design and Modelling of Mechanical Systems, March 23-25, 2005, Hammamet, Tunisia. [5] A. Benjeddou, J.-A. Ranger, Use of shunted shear-mode piezoceramics for structural vibration passive damping, Computers and Structures, accepted.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
162
Optimal control of piezoelectric anisotropic plates I. N. Figueiredo∗, G. Stadler ∗ ∗Department of Mathematics, University of Coimbra
Apartado 3008, 3001-454 Coimbra Portugal [email protected] & [email protected]
ABSTRACT Piezoelectric materials deform when they are subject to an electric field. This behavior, known as inverse piezoelectric effect, can be used to design smart materials. In order to obtain the desired behavior of these materials, one can either combine numerous simulations with physical intuition, or utilize an optimization-based method. We apply the latter approach to a recently derived model for piezoelectric anisotropic plates (see [1]). To be precise, we formulate the problem as optimal control problem, i.e., we search for an applied electric field that generates a deformation of the plate, which is as close as possible to the given desired deformation. This is done by introducing a certain cost functional involving both the electric field and the corresponding deformation. The optimal electric field is then characterized as minimizer of that functional. To model physical limitations we additionally impose bound constraints on the electric field. The resulting nonlinear system of coupled partial differential equations is discretized using finite elements and solved using a generalized Newton method (see [2]). In a comprehensive numerical study we consider, among others, plates composed of two layers of different piezoelectric materials. We interpret the derived optimal electric fields, investigate the influence of constraints imposed on these fields and discuss the performance of our algorithms.
References [1] I. N. Figueiredo and C. F. Leal: A Piezoelectric Anisotropic Plate Model. Asymptotic Analysis, 44, 3–4, 327–346, 2005. [2] M. Hinterm¨uller, K. Ito and K. Kunisch, The primal-dual active set strategy as a semismooth Newton method. SIAM J. Optim, 13(3), 865–888, 2003.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
163
Residual Internal Forces in Stiffened Thermal-Bimorph Actuator after Forming Process Wiktor L. Gambin*, A. Zarzycki† *
Warsaw University of Technology Poland [email protected]
†
Warsaw University of Technology Poland [email protected]
ABSTRACT
Thermal-bimorph (bimaterial) actuators are basic elements of MEMS ciliary arrays used for moving and positioning of small objects [1-3]. The arrayed actuators are deformable microstructures that may curl into and out of the substrate plane. Objects placed on the array are moving on the tips of actuators cyclically going down and up. Motion of the ciliary actuators is due to different thermal expansion of two polyimide layers with an integrated heater resistor between them. When an electric current is passed through the heater resistor, the temperature of the actuator increases and the structure, initially deflected out-of-plane, deflects downward. The above process requires of the actuators to generate not only large deflections but also a considerable force. The triangle-shaped actuator proposed in the paper [3] is such a structure. Two perpendicular bars rigidly connected at the moving tip and firmly fixed to the substrate plane at the unconnected ends are a stiffened frame structure with additional kinematical constrains. These constrains generate interaction forces between the connected beams during the forming process. In turn, the interaction forces have influence on the internal forces generated during the loading process. In the presented article, the triangle-shape actuator is considered as initially flat, layered frame structure, which becomes the curved 3-D stiffened structure during the cooling process. The cooling down beams are bent in two orthogonal planes not only due to change of the temperature, but also due to additional kinematical constrains. Relations between bending moments, curvature variations and temperature changes enable to find the residual internal forces on the purely analytical way.
References [1] N. Takeshima and H. Fujita, “Polyimide bimorph actuators for a ciliary motion system”, ASME WAM Symp. Micromech. Sensors, Actuators, and Systems, DSC-32, 203-209, 1991. [2] J. W. Suh, S. F. Glander, R. B. Darling, C. W. Storment, and G. T. A. Kovacs, “Organic thermal and electrostatic ciliary microactuator array for object manipulation”, Sensors and Actuators, A: Physical, 58, 51-60, 1997. [3] J. W. Suh, R. B. Darling, K. –F. Boehringer, B. R. Donald, H. Baltes, and G. T. A. Kovacs, “CMOS integrated ciliary actuator array as a general-purpose micromanipulation tool for small objects”, J. Micromech. Syst., 3, 4, 483-496, 1999.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
164
Spectral Level Set Methodology in the Optimal Design of Adaptive Aeroelastic Structures Alexandra A. Gomes∗, Afzal Suleman ∗ ∗ IDMEC, Instituto Superior T´ecnico Department of Mechanical Engineering Av. Rovisco Pais 1049-001 Lisbon, Portugal [email protected], [email protected]
ABSTRACT This paper proposes a topology optimization approach to the design of adaptive aeroelastic structures. We describe the optimal design of a morphing airfoil for increased roll maneuvering performance using the spectral level set methodology. Structural topology optimization is considered to be the next step in achieving better designs, following size and shape optimization, because the topology of the set constituting the structure is allowed to change. That is, holes may appear or disappear, and breakages or merges of the structure may occur. The level set methods are now an established framework to formulate problems in topology optimization. These methods consider the structural boundary to be an interface, which is modelled as the zero level set of a function. The evolution of this function during the optimization implicitly describes the evolution of the structural interface. The main advantage of this approach is the easy description of topology changes. However, the classic level set function evolves through a partial differential equation which requires specific numerical techniques to yield the correct solution, given the nodal values of the function on a spacial grid. Here, we take a frequency-domain approach to circumvent this disadvantage: the function is expanded into a Fourier series and the first few Fourier coefficients become the design variables assigned to structural definition. Another advantage of this approach, known as spectral level set methodology, compared to classic level set methods is the nucleation of new holes in the interior of the interface. For completeness, we provide an upper bound for the total error, which includes an estimate of the error committed in truncating the Fourier series. Benchmark examples in structural topology optimization, such as the design of short and long cantilevers for maximum stiffness given an amount of material, have already validated the proposed methodology. In this work, we study the problem of aileron control reversal. In particular, we are interested in generating additional lift to counteract the loss of aileron effectiveness due to the elastic properties of the wing. We consider an airfoil with a system of actuators set along its chord. These actuators operate on the airfoil mean camber line to produce additional lift. The airfoil’s morphing capability arises from the changes in its camber line. The optimization problem consists in determining the state of actuation which minimizes the actuation power while generating a prescribed amount of lift. The domain of the level set function is the airfoil’s chord: if the function is positive, the actuator is active and, at that location, the camber is increased by a positive constant; if the function is negative, the actuator is off. We show the topology of the optimum set of activated actuators is distinct from the topology of the initial guess and that the spectral level set methodology can adequately handle the occurrence of spike-like functions with a very small number of Fourier coefficients.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
165
Nondestructive identification of defects for smart plates in bending using genetic algorithms Daniela G. Marinova†, Dimitar H. Lukarski †, Georgios E. Stavroulakis *, Emmanuel C. Zacharenakis& *
Dept. of Production Engineering and Management, Technical University of Crete, Chania, Greece [email protected] †
Faculty of Applied Mathematics and Informatics, Technical University, Sofia, Bulgaria [email protected], [email protected]
&
Department of Civil Engineering, Technological Educational Institute of Crete, Heraklion, Greece [email protected]
ABSTRACT A defect identification problem for elastic plates with damages is studied in this paper. The classical theory of thin plates in bending is applied for the modelling of the mechanical structure. Bonded piezoelectric sensors and actuators are considered in a simplified way. Within classical finite element discretization, cracks and other defects are modelled in a smeared-crack sense by reducing the stiffness of the corresponding element. According to the simplicity of the model, only the position of the possible crack is considered to be the unknown. The most general case of dynamical excitations is considered. The identification is based on dynamic non-destructive loading. A suitable error norm is used to transform the defect identification problem to a nonconvex output error optimisation problem [1], [2]. The difference between the dynamic response of the plate in bending with and without cracks demonstrates the areas of the plate where the influence of the cracked element is higher. The position of the defect, which is unknown in real applications, can be computed from the solution of the arising optimisation problem. This problem has been solved by a genetic algorithm. The investigation includes the effect of different types of boundary conditions. In all cases the error function, which depends on the boundary conditions and the position of the defect, may have local minima and one global minimum, exactly at the position of the real crack. As a general observation, the boundary conditions, the loading and the shape of the structure, as well as the position of the measurement points and the duration of the considered time interval influence the shape of the error function. Numerical results show that by using the genetic algorithm the crack position can be found. Moreover, for a relatively high population size (about 15-20) the probability of finding the crack position on the first few steps is very large.
References [1] G.E. Stavroulakis, Inverse and crack identification problems in engineering mechanics. Kluwer Academic Press, Dordrecht, Boston, London, 2000. [2] G. Liu, X. Han, Computational Inverse Techniques in Nondestructive Evaluation. CRC Press, Boca Raton, 2003.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
166
Modeling Shape Memory Alloy Plane Truss Structures using the Finite Element Method Juliana Hoyer Insaurrauld Pereira*, Mauricio Rangel Pacheco*, Pedro Manuel Calas Lopes Pacheco*, Ricardo Alexandre Amar de Aguiar*, and Marcelo Amorim Savi† * 1 CEFET/RJ - Department of Mechanical Engineering Av. Maracanã, 229, 20271-110 - Rio de Janeiro - RJ - Brazil [email protected], [email protected], [email protected], [email protected] †
UFRJ/COPPE – Department of Mechanical Engineering 21.945.970 – Rio de Janeiro – RJ, P.O. Box 68.503 - Brazil [email protected]
ABSTRACT The remarkable characteristics of shape memory alloys (SMA) have been responsible for the increasing interest in different applications varying from biomedical to aerospace industry. During the recovering process of a SMA component, large loads and/or displacements can be generated in a relatively short period of time making this component an interesting mechanical actuator. The thermomechanical behavior of SMA is related to phase transformations induced by stress and/or temperature variations. This article deals with the modeling and simulation of SMA plane truss structures using an anisothermal constitutive model with internal variables that includes three macroscopic phases in the formulation: two variants of martensite and an austenitic phase. A numerical procedure is developed based on the operator split technique associated with an iterative numerical scheme in order to deal with nonlinearities in the formulation. With this assumption, coupled governing equations are solved considering three uncoupled problems: thermal, thermoelastic and phase transformation behaviors. The thermal problem comprises a one-dimensional conduction problem with surface convection. Finite element method is employed for spatial discretization. The thermo-elastic problem evaluates stress and displacement fields from temperature distribution, employing the nonlinear finite element method. Finally, the phase transformation problem determines the phase transformation fields considering the phase evolution in the process. Numerical simulations treats SMA plane truss structures subjected to thermomechanical loadings. The analysis considers results obtained for two models: uncoupled and coupled. The uncoupled model neglects the thermomechanical couplings, corresponding to the rigid body energy equation. The coupled model considers the latent heat associated with phase transformation as a source in the energy equation. Results show that the proposed model captures the general behavior of SMAs, allowing the description of adaptive trusses with large displacements. Moreover, they show the some situations where the thermomechanical coupling plays an important role in the description of SMA behavior.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
167
Evaluation of NiMnGa Magnetic Shape Memory Alloys Using Cellular Neural Networks Gursev Pirge*, Niyazi Kılıç†, Osman N. Uçan†, Sabri Altıntaú* *
†
Department of Mechanical Engineering, Bo÷aziçi University 34342, Bebek, Istanbul, Turkey [email protected], [email protected]
Department of Electrical&Electronics Engineering, Istanbul University 34320, Avcılar, Istanbul, Turkey [email protected], [email protected]
ABSTRACT In this study, CNN–RPLA (Cellular Neural Network-Recursive Perception Learning Algorithm) was used to enhance the Scanning Electron Microscope (SEM) microstructural images of NiMnGa magnetic shape memory (MSM) alloys. Since their introduction in 1988 by Chua, CNN has attracted a lot of attention. Not only from a theoretical point of view these systems have a number of attractive properties, but also furthermore, there are many well-known applications like image processing, motion detection, pattern recognition, simulation. Here, CNN approach was used to enhance SEM images using CNN approach to analyse the various phases in the austenitic phase. MSM alloys are a class of actuator materials which produce strain via the magnetic field induced reorientation of twin variants in response to an applied magnetic field. MSM effect depends on the success of parameters like mobility of twin boundaries, magnetic properties of the alloy, proper specimen orientation and specimen shape. In order to produce a strong MSM effect, it is necessary to obtain a uniform martensite in the entire sample. The martensite transformation temperature is very sensitive to the alloy composition. A single phase having a homogeneous composition is thus desirable in order to avoid having different components of the microstructure undergoing the martensite transformation at different temperatures, or not undergoing the transformation at all in the case of the eutectic structures and Mn-rich particles. The results showed that as solidified, off-stoichiometric alloys had three distinct microstructural features—a Heusler phase, a Mn Rich phase and a eutectic or eutectoid region. The latter could be removed by prolonged annealing at elevated temperatures, but that the coarse Mn-rich particles are much more difficult to remove. This phase is likely harmful to the mechanical properties of the alloy and should be eliminated in the future.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
168
Modelling of fibre Bragg grating sensor plates C.A. Ramos†, R. de Oliveira*, R.D.S.G. Campilho‡, A.T. Marques‡ †
Instituto Superior de Engenharia do Porto (ISEP), Rua Dr. António Bernardino de Almeida 431, 4200-072, Porto, Portugal [email protected]
*
Instituto de Engenharia Mecânica e Gestão Industrial (INEGI), Rua do Barroco, 174, 4465-591, Leça do Balio, Portugal. [email protected] ‡
Departamento de Engenharia Mecânica e Gestão Industrial, Faculdade de Engenharia da Universidade do Porto (FEUP), Rua Dr. Roberto Frias, s/n 4200-465 Porto, Portugal [email protected]
ABSTRACT In this paper is presented the design of a composite sensor plate, based on fibre Bragg grating (FBG) sensors, to be used as alternative to the conventional electric strain gages. The use of such composite sensor plate will permit to profit of FBG sensors advantages compared to conventional electrical strain gages increasing its safety considering that they are commonly simply surface mounted in structure using adhesives. Here, contrarily to what is traditionally performed, FBG sensors are embedded in thin (0.4 mm of thickness) weaved carbon fibre reinforced composite plates. The FBG sensor is hence not oriented parallel to the surrounding reinforcement. Such configuration is known to induce changes on the reflected optical power spectrum of the FBG sensor resulting in an inaccurate answer. A methodology was then developed to guarantee that the resulting FBG sensor optical power spectrum didn’t exhibit any aspect change. The resulting composite sensor plate was mounted on the surface of a composite specimen which was submitted to tensile loading. The axial strain answer of the composite plate sensor is compared to the answer of an electrical strain gage. A three dimensional finite element study is proposed to understand the relation between the strain measured by the FBG sensor and the strain imposed to the host plate and especially the consequence of using such composite sensor plate on the behaviour of tensile test specimen. The benefits and drawbacks of the use of composite sensor plate are then discussed in light of these results.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
169
Refined Finite Element Model for Vibration Analysis of Sandwich Beams with Shear Piezoelectric Actuators and Sensors Marcelo A. Trindade*, Ayech Benjeddou† *
Department of Mechanical Engineering, São Carlos School of Engineering, University of São Paulo, Av. Trabalhador São-Carlense, 400, 13566-590 São Carlos, Brazil [email protected] †
Laboratoire d'Ingénierie des Systèmes Mécaniques et des Matériaux, Institut Supérieur de Mécanique de Paris, 3 rue Fernand Hainault, 93407 Saint Ouen, France [email protected]
ABSTRACT High stresses and possible impacts of surface-mounted piezoelectric actuators can be alleviated by embedding axially poled piezoceramic actuators between two elastic layers. In this case, the application of a transverse electric field induces shear deformation of the actuator thus generating the desired sandwich structure deflection. Although this so-called shear actuation mechanism seems quite promising for structural control, its modelling is still an open issue. For piezoelectric shear actuated sandwich beams, either the classical sandwich theory (CST) or first and higher-order equivalent single layer (ESL) theories were used. However, ESL theories fail to model localized core shear deformations, which are determinant to correctly evaluate the shear actuation of the sandwich beam. This work extends a previously presented refined sandwich beam finite element (FE) model [1] for vibration analysis. The mechanical model is a refinement of CST, for which the core is modelled with a third-order shear deformation theory [2]. The FE model is developed considering, through the beam length, electrically: constant electric difference of potentials for the piezoelectric facing and core layers and quadratic third-order variable of the electric potential in the core, while mechanically: linear axial displacement and quadratic bending rotation of the core, and cubic transverse displacement of the sandwich beam. Despite the refinement of mechanical and electrical behaviours of the piezoelectric core, the model leads to the same number of degrees of freedom (dof) as the previous CST one due to a two-step static condensation of the internal dof (bending rotation and core electric potential third-order variable). The proposed FE model is validated through the comparison with numerical and experimental results [3]. Results confirm that the TSDT and the induced cubic electric potential yield an extra stiffness to the sandwich beam.
References [1] Trindade, M.A. and Benjeddou, A. Refined sandwich finite element model for smart beams with shear piezoceramic actuators and sensors, in II Eccomas Thematic Conference on Smart Structures and Materials, C.A. Mota Soares et al. (eds.), Lisbon, July 2005. [2] Reddy, J.N., A simple higher-order theory for laminated composite plates, Journal of Applied Mechanics, 51(4):745-752, 1984. [3] Baillargeon, B.P. and Vel, S.S. Active vibration suppression of sandwich beams using piezoelectric shear actuators: experiments and numerical simulations. Journal of Intelligent Material Systems and Structures, 16(6):517–530, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
170
Thermoelectromechanical Response of a Parallel Crack in a Functionally Graded Piezoelectric Strip S. Ueda*, H. Kondo* *
Department of Mechanical Engineering, Osaka Institute of Technology 5-16-1 Omiya, Asahi-ku, Osaka, 535-8585, JAPAN [email protected]
ABSTRACT Possible use of distributed actuators and sensors are discussed in the light of smart or intelligent material technology. An area where smart material may have an advantage is to sense thermally induced distortions and to adjust for adverse thermomechanical conditions. As a result, several analytical studies concerned with piezothermoelasticity of homogeneous materials were reported. Recently, with the help of the development in modern material processing technology, functionally graded piezoelectric materials (FGPMs) have been developed to improve their reliability, and the electromechanical fracture of the FGPM has received much attention. Moreover, so much attention has been focused on the thermoelectromechanical fracture analysis of homogeneous piezoelectric materials. However, because the FGPMs are just an emerging class of piezoelectric materials, there are still very few articles considering the fracture problem in an FGPM under the thermoelectromechanical loadings. For example, Wang and Noda investigated the thermally induced fracture of a smart functionally graded composite structure, and the present author also studied the fracture of a functionally graded piezoelectric strip due to the thermal load. In this paper, the mixed-mode thermoelectromechanical fracture problem for a functionally graded piezoelectric material strip is considered. It is assumed that the thermoelectroelastic properties of the strip vary continuously along the thickness of the strip, and that the strip is under the thermoelectric loadings. The crack faces are supposed to be insulated thermally and electrically. By using the Fourier transform, the thermal and electromechanical problems are reduced to a singular integral equation and a system of singular integral equations, respectively, which are solved numerically. Numerical calculations are carried out, and detailed results are presented to illustrate the influence of the crack length, the crack location and the material nonhomogeneity on the stress and electric displacement intensity factors. The temperature-stress distributions are also presented. The following facts can be found from the numerical results. Firstly, the normalized intensity factors are under the great influence of the geometric parameters. Secondly, the intensity factors of crack near the free surfaces due to the thermal load are not so large. This phenomenon is quite different from the intensity factors under the pure electric load. Finally, the effect of the material nonhomogeneity on the intensity factors depends on the geometric parameters.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
171
Multi-Scale Finite Element Modeling of Piezoelectric Materials by A Crystallographic Homogenization Method Yasutomo Uetsuji*, Eiji Nakamachi *
Osaka Institute of Technology 5-16-1 Omiya, Asahi-ku, Osaka 535-8585 [email protected]
ABSTRACT Polycrystalline piezoelectric materials have been used for actuators or sensors as a component of various electronic and mechanical devices. Higher performance is becoming required for piezoelectric materials as they are applied to new technological fields such as micro/nano machines. Each crystal grain in piezoelectric materials shows strong anisotropy in mechanical and electrical behaviors. Macroscopic properties of polycrystalline piezoelectric materials are dominated by microscopic inhomogeneous crystal morphology. Therefore, polycrystalline piezoelectric materials have a large possibility to exhibit higher performance in a macroscopic scale by design of crystal morphology in a microscopic scale. In this study, a multi-scale finite element modeling by “crystallographic homogenization method” is proposed to estimate macroscopic properties considering microscopic inhomogeneous crystal morphology, and to evaluate microscopic behaviors in response to macroscopic external loads as shown in Figure 1. The computational examples of homogenization and localization are presented for a typical piezoelectric material, barium titanate (BaTiO3) with various distributions of crystal orientations. And then, its crystal orientation distribution has been optimized by steepest decent method to maximize macroscopic piezoelectric strain constants. Computational results indicated that piezoelectric strain constants d33 and d31 increase 34% and 180% respectively, compared with conventional piezoelectric polycrystals. It should be emphasized that the optimized polycrystals have higher piezoelectric performance than single crystals.
Figure 1 Hierarchical structure of polycrystalline piezoelectric materials.
References [1] Y. Uetsuji, Y. Nakamura, S. Ueda and E. Nakamachi, Numerical investigation on ferroelectric properties of piezoelectric materials using a crystallographic homogenization method. Modelling Simul. Mater. Sci. Eng., 12, S303-S317, 2004.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
172
Vibration Control of A Laminated Composite Plate Subjected to Blast Loading H. Uyanık*, Z. Mecitoğlu† * Turkish Air Force Academy Yeşilyurt, 34149 İstanbul, Turkey [email protected] † İstanbul Technical University Maslak, 34469 İstanbul, Turkey [email protected]
ABSTRACT In this numerical study, vibrations of a cantilevered composite plate subjected to blast loading are suppressed by the use of piezoelectric actuators. Friedlander’s exponential decay function is used for expressing the blast load model. Some parameters of the function are obtained from the experimental studies. A semiloof shell element is developed in order to account for piezoelectric effects. The composite plate is discretized by using the semiloof elements and stiffness and mass matrices of the plate are obtained from the finite element model. In order to reduce the degrees of freedom of the finite element model, mode summation method is used with weighted modal vector including dominant modes in the dynamic behavior. Free vibrations, static behavior and transient vibrations under the blast load are solved by using the full and reduced matrices as well as by using ANSYS software. All results are in a good agreement. State-space equations are obtained from the reduced finite element model. It is proved that the system equations satisfy the controllability condition in order to control the system. Since the system is also desired to be controlled by using a state observer, the observability condition is satisfied for the system. Since the system is on the stability boundary due to neglecting structural damping, the feedback gain matrix of the system is obtained by using optimal linear quadratic regulator (LQR) in order to guarantee the stability of the system. Structural vibrations have been suppressed successfully by using a state observer control system which estimates system states using displacements measured from sensors.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
173
Experimental Identification of GHM and ADF Parameters for Viscoelastic Damping Modeling C. M. A. Vasques∗, R. A. S. Moreira† and J. Dias Rodrigues∗ ∗ Faculdade de Engenharia da Universidade do Porto Departamento de Engenharia Mecˆanica e Gest˜ao Industrial Rua Dr. Roberto Frias s/n, 4200-465 Porto, Portugal [email protected] and [email protected] †Universidade de Aveiro Departamento de Engenharia Mecˆanica Campus Santiago, 3810-193 Aveiro, Portugal [email protected]
ABSTRACT Viscoelastic materials can be used as an effective means of controlling the dynamics of structures, reducing and controlling the structural vibrations and noise radiation. They can be used as surface mounted or embedded damping treatments, utilizing passive viscoelastic materials alone, the so-called passive treatments, or in an unified way with active materials such as piezoelectrics, the so-called hybrid treatments. The use of these materials in damping treatments provides high damping capability over wide temperature and frequency ranges. The extensive use of passive or hybrid treatments using viscoelastic materials has motivated the development of damping models to be used and integrated into commercial or home-made finite element (FE) codes. The implementation of the Golla-HughesMcTavish (GHM) and anelastic displacement fields (ADF) models in a general FE model with viscoelastic damping is presented and discussed in this paper. Additionally, a direct frequency analysis (DFA) is also described and employed. A methodology to identify the complex shear modulus of viscoelastic materials is described. Thus, the identified complex shear modulus of the viscoelastic material 3M ISD112 is curve-fitted in order to obtain the modeling parameters of the GHM and ADF models. A sandwich plate with a viscoelastic core and elastic skins is analyzed. Measured and FE-based predicted FRFs based on a DFA, GHM and ADF models, were compared in order to assess the damping models and validate the experimental procedure for the material properties identification and the curve fitting process. It was found that the application of a discrete dynamic system, describing a SDoF analytical model, provides a reliable identification methodology, since it is based on the direct (in opposition to indirect measuring approaches based on vibrating beams) characterization of the complex stiffness of a viscoelastic material sample in shear deformation, providing results similar to those published by the material manufacturer. Regarding the internal variables models under analysis here, which were implemented at the FE model level, the ADF model leads to an augmented model of the damped structural system with a lower size than the GHM model. To the opinion of the authors, the ADF model represents the best alternative to accurately model the damping behavior since it yields good trade-off between accuracy and complexity. One major disadvantage in using internal variables models such as the GHM or ADF is the creation of additional dissipation (or anelastic) variables increasing the size of the coupled damped FE model. However, an alternative based on the DFA using the FE spatial model and re-calculating the complex viscoelastic stiffness matrix for each discrete frequency value might be used with the outcome of being simpler to implement and the drawback of being time-consuming and not providing directly the modal parameters of the damped structural system. All the models showed similar accuracy and yielded representative results of viscoelastically damped structural systems.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
174
Numerical Aspects of Modelling Thermo- Mechanical Wave Propagation With Phase Transformations L. X. Wang∗, R. V. N. Melnik† ∗
MCI, Faculty of Science and Engineering, University of Southern Denmark, Sonderborg, DK-6400, Denmark [email protected]
† Mathematical Modelling and Computational Sciences,
Wilfrid Laurier University, 75 University Avenue West, Waterloo, ON, Canada, N2L 3C5 [email protected]
ABSTRACT Due to their unique thermo-mechanical properties, the range of existing and potential applications of shape memory alloys (SMA) continues to grow. Many of these applications take advantage of the dynamic response of SMA under dynamic loading conditions. From the engineering design point of view, this requires a better understanding of the effect of phase transformations and thermo-mechanical coupling on wave propagation in the material. In achieving this goal, a fundamental task is to analyse the dynamics of first order phase transformations induced by shock loadings. In this contribution, a mathematical model and its numerical discretization are constructed to analyse the wave propagation in shape memory alloy rods. The first order martensitic transformations and the associated effects of thermo-mechanical coupling are accounted for by employing the modified Ginzburg-Landau-Devonshire. The Landau-type free energy function characterizes different phases, while a Ginzburg term is introduced to account for the internal friction during phase transformations. The effect of the Ginzburg term on wave propagation patterns is analysed under shock loadings implemented via stress boundary conditions. For practical numerical simulations of SMA samples, the constructed model of coupled nonlinear system of PDEs is reduced to a system of differential-algebraic equations, where the Chebyshev collocation method is employed for the spatial discretization, while the backward differentiation is used for the integration in time. A series of numerical experiments is carried out on copper-based SMA samples. Propagation of stress waves induced by shock loadings is analysed for different initial temperature. It is demonstrated that the patterns of wave propagation is complicated at low temperatures by phase transformations, while more regular patterns are observed for high temperature distributions. These observations are in agreement with experiments. Finally, the influence of viscosity effects on the overall thermo-mechanical behaviour of rods is analysed numerically by evaluating the contribution of the Ginzburg term responsible for the internal friction during phase transformations. Key words: Thermo-mechanical coupling, martensitic transformations, shock waves, Landau-Ginzburg theory, Chebyshev collocation method.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
175
Analysis and Design Optimization of Smart Laminated Composite Beams using Layerwise Theory A. Zabihollah*, R. Ganesan†, R. Sedaghati+ *†+
Dept. of Mechanical and Industrial Engineering Concordia University 1515 St. Catherine W., Montreal, Quebec, Canada H3G 2W1, * [email protected], † [email protected], + [email protected]
ABSTRACT Many of the developed models for smart laminated composite beams are based on the single-layer theories. Smart laminated composite beams contain strong inhomogenities through the thickness which lead to erroneous results when these beams are analyzed using single-layer theories. However, accurate results can be achieved by using three-dimensional model by setting up computationally expensive refined meshes. It has been demonstrated that layerwise theory can be applied for the analysis of laminated beam with integrated piezoelectric layers as sensors and actuators with acceptable accuracy and computational efforts [1]. The present work contains two major aspects; first, a finite element model based on the layerwise theory has been developed to investigate the actuation and sensing mechanism of extensional piezoelectric surfaces bonded and embedded as continuous or discrete patches in a composite laminate. Also the effect of shear piezoelectric patches embedded in a composite laminate has been investigated using the developed layerwise model. The elctro-mechanical coupling effect is included. The second aspect concerns with design optimization. Most of the developed models of smart laminated composite beams which have been used for optimization are based on single-layer theories. One of the most recent publications in this field has been the work of Soares et al [2]. From literature survey, it is concluded that smart laminated beam model based on the layerwise theory has not been used for design optimization. In the present work, such a model is developed and used for design optimization. In order to determine the optimal design of the beam for selected purposes, a gradient based optimization procedure, namely, Sequential Quadratic Programming (SQP) is used where the objective is to minimize the mass of the structure while various constraints including layer stress and displacements for static problem as well as frequency constraints for eigenvalue problems are considered. Illustrative examples are given to validate the formulation.
References [1] J.N., Reddy, On laminated composite plates with integrated sensors and actuators. Engineering Structures, 21, 568-593, 1999. [2] C.M.M., Soares, C.A.M., Soares, V.M.F., Correia, Optimal design of piezo-laminated structures. Composite Structures, 47(1-4), 625-634, 1999.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
176
A thermo-viscoplastic model for bituminous materials Hervé Di Benedetto*, Brice Delaporte*†, Cédric Sauzéat *, Mondher Neifar+ *
“Departement Génie Civil et Bâtiment” laboratory of ENTPE, Rue Maurice Audin, 69518 Vaulx-enVelin, France [email protected] [email protected] *†
“Departement Génie Civil et Bâtiment” laboratory of ENTPE, Rue Maurice Audin, 69518 Vaulxen-Velin, and TOTAL France, Centre de Recherche de Solaize, France [email protected] + Ecole Supérieure des Sciences et Techniques de Tunis 5 avenue Taha Hussein, 1008 Monfleury Tunis, Tunisie [email protected]
ABSTRACT This paper introduces the 3D formalism of the DBN (Di Benedetto, Neifar) model developed at ENTPE (Ecole Nationale de Travaux Publics de l’Etat). This model is an attempt to describe with a unique formalism the different types of behavior observed for bituminous materials. The DBN model is very versatile. The proposed formulation can be simplified or adapted following the required property to be introduced. The law can then be very simple and easy to use (linear viscoelastic or even elastic) or more complicated (introduction of non linearity, permanent deformation or fatigue). Considering the thermo-sensitivity of bituminous materials, the temperature influence is always considered. The presented developments focus on the modeling of linear behavior, which is observed for bituminous mixes in the small strain domain (i.e. strain amplitudes less than some 10-5 m/m). The non linear behavior up to failure, which can be ductile or brittle, the rutting and the fatigue phenomena are only evoked due to the lack of space. These phenomena have been treated in others publications. In this paper, the three-dimensional (3D) linear viscoelastic (LVE) behavior is investigated. Complex Poisson’s ratio (Q*) is measured and introduced. Its evolution with temperature and frequency is studied for different bituminous materials. Experimental results show that the Time Temperature Superposition Principle is applicable in the 3D case. The same shift factor applies for E* and Q*. Comparisons between simulations in the linear and non-linear domains and experimental data are proposed. Thermal Stress Restrained Specimen Tests (TSRST) which introduce thermo-mechanical coupling are also simulated.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
177
From Asphalt to the Arctic: New Insights into Thermo-Mechanical Ratchetting Processes James G A Croll* *
Department of Civil and Environmental Engineering, University College London Gower Street, London WC1E 6BT, UK [email protected]
ABSTRACT Observation of upward bulges forming on the asphalt overlays applied to the pavements of London (and incidentally many other Cities), have recently been re-explained as a form of thermal ratchet buckling process. At many orders of magnitude greater temporal and spatial scales, a similar process is suggested to be taking place in the seasonal growth of the characteristic feature within permafrost regions, particularly in the Arctic, often referred to as pingos. Consideration of this specific example of analogous behaviour between asphalt and permafrost has led to a greater awareness that further close relationships between the mechanics of periglacial processes and those occurring in the morphology of asphalt might exist. This paper will explore some of these close mechanical analogies and in the process challenge in both fields some of the accepted wisdom as to the reasons for the formation of these analogous features. For example, it will be suggested that the thermo-mechanical process responsible for the development if ice-wedges within areas of permafrost are closely related, in terms of the thermo-mechanical processes at work, to the development of certain forms of cracking within sheets of asphalt. Extending this analogous relationship between periglacial processes and asphalt failure phenomenon, it will be argued that the formation of ice-wedge-polygons in permafrost and the development of “alligator cracking” in asphalt also involve very similar mechanics. Furthermore, it will be suggested that the hysteretic effects arising from alternations of heating and cooling are responsible for many other related morphological features of asphalt and permafrost. Certain forms of motion of either ice or asphalt, that are difficult to explain in terms of the effects of gravity alone, become explicable in terms of a form of thermo-mechanical ratchetting. While in the case of periglacial features the interest is largely scientific curiosity, although even here there are significant implications for climate change, for asphalt the mechanics of failure have serious economic implications. By drawing-out the analogies between the mechanics of processes within these two materials it is argued that we will be in a better position to understand and mitigate the worst consequences from these various phenomena.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
178
An Object-Oriented System for Finite Element Analysis of Pavements Aurea Silva de Holanda*, Evandro Parente Junior†, Teresa Denyse Pereira de Araújo†, Lucas Tadeu Barroso de Melo*, Francisco Evangelista Junior*, Jorge Barbosa Soares* * Federal University of Ceará Department of Transportation Engineering, Campus do Pici, Bl. 703, 60455-760, Fortaleza, Ceará, Brazil {aurea, lucas, fejr, jsoares}@det.ufc.br † Federal University of Ceará Department of Structural Engineering, Campus do Pici, Bl. 710, 60455-760, Fortaleza, Ceará, Brazil {evandro, denyse}@ufc.br
ABSTRACT The calculation of displacements, stresses and strains caused by vehicle loads in pavements is not a simple task even when considering all layers formed by linear elastic materials. In reality, surface and granular layers present a complex constitutive behavior, with nonlinear and time-dependent effects. Such effects should be considered in mechanistic pavement design methodologies which make use of the pavement structural response into specific distress models [1]. Today, there is a trend in the pavement academic community to substitute pavement analysis based on the Multilayer Elastic Theory by analysis based on the Finite Element Method – FEM [2]. There are several different finite element programs for pavement analysis [2, 3]. Most of these programs consider only axisymmetric models and the three-dimensional stress state due to vehicle loads is computed using superposition, which is not correct for nonlinear materials. Moreover, the existing pavement specific programs were developed for design purposes and do not allow the modeling of damage evolution (e.g., crack propagation in bituminous mixtures), which is an important topic in the pavement research community. In this paper, a new computational system developed to be used in both pavement design and research is presented. The system is based on the FEM and is implemented using Object-Oriented Programming (OOP) techniques to make it easily extendable. It contains both 2D (axisymmetric, plane-strain and plane stress) and 3D analysis models and works with different element shapes (triangular, quadrilateral, bricks, etc.) and interpolation orders (linear and quadratic). It also provides an efficient and accurate modeling of different loading types, including time varying loads. Finally, the system provides different numerical algorithms to nonlinear and time-dependent analysis, as well as a set of constitutive models. In this work, the class hierarchy of the system is presented and its main features are thoroughly discussed.
References [1] Y. H. Huang, Pavement Analysis and Design, Second edition, Prentice Hall, Inc., Englewood Cliffs, New Jersey, USA, 2004. [2] NCHRP/TRB, Guide for Mechanistic-Empirical Design of New and Rehabilitated Pavement Structures, Appendix RR: Finite Element Procedures for Flexible Pavement Analysis. 2004. [3] Harichandran, R.S., Yeh, M.-S., and Baladi, G.Y. “MICHPAVE: A Nonlinear Finite Element Program for the Analysis of Flexible Pavements,” Transportation Research Record, 1286, 1990.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
179
On the treatment of convective terms in coupled hydro-mechanics for porous media subject to dynamic loading Bernd Lenhof, Per Kettil, Kenneth Runesson, Nils-Erik Wiberg Department of Applied Mechanics, Chalmers University of Technology S-41296 G¨oteborg, Sweden [email protected]
ABSTRACT The physical problem of interest is that of a road structure that is subjected to dynamic loading from repeated over-rolling of car wheels. Primarily, we are interested in the mechanical response of bitumenbased porous granular media (such as the asphalt layer). The porous medium is modelled as a mixture of a solid phase, in the sense of a porous solid skeleton, and a fluid phase that represents both liquid and air in the pores. The solid particles are assumed to be intrinsically incompressible, i.e. the compressibility of the solid bulk is brought about by a rearrangement of the particles. In the presence of air, the fluid is assigned a finite intrinsic compressibility; hence, it suffices to consider a binary mixture. An important practical problem is internal erosion of the solid material by the fluid transport, which means that mass of the individual phases is not conserved; however, this effect is ignored here. A major issue, which is targeted in this contribution, is the relative importance of the various acceleration terms for both the solid and the fluid. In particular, we are interested in assessing the convective contributions in comparison with the intrinsic time derivative. In fact, the convective transport terms are normally ignored without any quantitative analysis supporting such a simplification. In order to simplify the computation without loss of the main characteristic, we restrict the formulation to small solid deformations and linear constitutive behavior (constant elastic stiffness and constant permeability). The results show that the introduction of the convective terms into the linearized balance equations can lead to significant differences in the solution of the seepage velocity field, depending on the material parameters. A simplified loading situation is considered: A pulsating stationary load replaces the moving load. A space-time finite element formulation is used that is based on the Galerkin method in time of zero order (which is basically the backward Euler method). In order to avoid using stabilization technique (such as SUPG), we consider very fine meshes in both space and time. The results of the assessment will be presented at the conference.
References [1] Reint deBoer, Theory of Porous Media - Highlights in the Historical Development and Current State. Springer Verlag, Berlin, 2000. [2] R. W. Lewis and B. A. Schrefler, The Finite Element Method in the Static and Dynamic Deformation and Consolidation of Porous Media. John Wiley & Sons, Chichester, 1998. [3] Kettil, P. and Engstr¨om, G. and Wiberg, N.E., Coupled Hydro-Mechanical Wave Propagation on Road Structures. Computers and Structures, 83, 1719-1729, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
180
Asphalt Mechanics, a Key Tool for Improved Pavement Performance Predictions A.A.A. Molenaar* * Delft University of Technology P.O. Box 5048, 2600 GA Delft, the Netherlands [email protected]
ABSTRACT Pavement design has relied for a very long time on simplified mechanistic methods and experience. The need for long life maintenance structures, the use of new, costly, materials with enhanced characteristics, the need to spend the maintenance euro as effective as possible, the need to quantify risks etc, have given a boost to a renewed interest in the characterization and modeling of pavement materials and structures. This includes proper characterization of materials obeying their stress dependent, rate and temperature dependent, non linear elasto-visco-plastic behavior. These advanced models are necessary to obtain a better understanding in why pavement materials and structures behave like they do and in order to be able to quantify e.g. the beneficial effect of costly new materials with enhanced characteristics. This paper describes a number of developments made in this field at the Delft University of Technology and the power and importance of these models is illustrated by means of two realistic examples. As an introduction a short description is given of the design methodologies as currently used.
References [1] A. Scarpas, CAPA-3D finite element system. User’s manual parts I, II and III. Delft University of Technology, Delft, 1992. [2] C.S. Desai, S. Somansundaram and G. Frantziskonis, Hierarchical approach for constitutive modeling of geologic materials. Int. Journal of Numerical and Analytical Methods in Geomechanics, Vol 10, No 3, 1986. [3] S.M.J.G. Erkens, Asphalt concrete response (ACRe) –determination, modeling and prediction-. PhD Thesis, Delft University of Technology, 2002. [4] T.O. Medani, Design principles of surfacings on orthotropic steel bridge decks. PhD Thesis, Delft University of Technology, Delft, 2006.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
181
Sensitivity of Blood Flow Patterns to the Constitutive Law of the Fluid ´ A. Feij´oo ∗ Pablo J. Blanco∗, Ignacio Larrabide∗, Santiago A. Urquiza∗∗, Raul ∗Laborat´orio Nacional de Computac¸a˜ o Cient´ıfica - LNCC Rua Getulio Vargas 333, 25651-057, Petropolis, RJ, Brazil pjblanco, nacho, [email protected] ∗∗Laboratorio de Bioingenier´ıa, Universidad Nacional de Mar del Plata
Av. J.B. Justo 4302, 7600 Mar del Plata, Argentina santiagourquiza@fi.mdp.edu.ar ABSTRACT It is well known that hemodynamic factors are strongly influenced by the arterial geometry. Combining computational fluid dynamics with three-dimensional medical data makes possible the study of blood flow in real geometries. By this means we are able to analyze the sensitivity of hemodynamic factors due to shape changes in vascular districts. It is also well known that the fluid’s constitutive law very much influences the flow structure in singularities, such as the carotid sinus. In this work we quantify the sensitivity of blood flow for a model of a carotid bifurcation due to different constitutive behavior. In this case, the flow pattern for the Casson constitutive equation for the fluid is compared with its Newtonian counterpart. To this end a multidimensional 3D-1D FEM model of the whole arterial tree is implemented. It comprises a 3D compliant model of the carotid bifurcation coupled with a 1D model for the remaining part of the arterial tree. With this approach, difficulties arising from the treatment of boundary conditions for the 3D model are naturally handled. In particular, two carotid bifurcation geometries were analyzed. One of them corresponds to a standard model taken from literature. The second geometry was acquired from a patient-specific angiography using image segmentation and reconstruction techniques. Detailed hemodynamic factors and flow patterns in the carotid bifurcation are provided. Finally, this data is analyzed in order to determine how these results are affected in the different cases under study.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
182
The influence of stem design on strains and micromotion in revision Total Knee Arthroplasty: Finite element analysis A. Completo*, F. Fonseca†, J. A. Simões* * Departamento de Engenharia Mecânica Universidade de Aveiro, 3810-193 Aveiro [email protected] † Faculdade de Ciências da Saúde Universidade da Beira Interior, 6201-001 Covilhã [email protected]
ABSTRACT The main objective of this study was to compare the effect of tibial stem design on load transfer, strains and relative micromotion between the tibial tray and bone. Attempts were also made to correlate FE results with clinical findings, like bone resorption, fibrous layer formation, radiolucencies and pain. The effect of the medial position of the tibial tray to obtain good alignment with press-fit long stems provoked higher strains when compared with the model where the stem was shifted medially. Cemented stems reduce load transfer by the tibial tray to proximal bone while pressfit stems transmit higher percentage of load. The idea that orthopaedic surgeons have that this kind of stems reduce load transmitted to the proximal bone is according to this study a wrong one. The hypothesis that load transferred at the distal tip of the press-fit stems occurs is true in an immediately pos-operative situation if micromotion is minimised due to an adequate press-fit. However, in the middle and long term, the share of load at the distal bone cannot not achieved. FE results demonstrated potential mechanical-clinical relations relative to bone resorption, radiolucencies and pain.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
183
Optimization of targeted movements Anders Eriksson KTH Mechanics Royal Institute of Technology, Osquars backe 18, SE-100 44 Stockholm, Sweden [email protected] ABSTRACT An algorithm was developed for the evaluation of targeted movements, between an initial and a final configuration, possibly with some intermediate configurations. The algorithm was primarily aimed at robotic and musculoskeletal movement simulations, and has been found efficient and reliable for problems with moderate numbers of displacement coordinates, even for complicated dynamic formulations, [1, 2]. The result from the algorithm contains the configuration as function of time, but also a set of a priori unknown control forces needed to create the desired motion. The algorithm is based on a temporal finite element interpolation of displacements and controls, with a third order Hermitian form for the displacement components and a linear interpolation for the control forces. This allows the governing differential equation of the movement to be satisfied at two collocation points in each of the time intervals. With sufficient freedom in the description of the control forces, they are chosen to optimize some measure of the movement or the controls. A common criterion is to minimize the needed forces, by formulating a cost function, which is the sum of square-integrated force components. Another interesting possibility is to seek the smoothest movement, which leads to a cost function based on the jerk values for the displacements, following an idea by Flash and Hogan, [3]. Both criteria were introduced in the algorithm. Examples have shown that the introduced optimization criteria strongly influence the obtained solutions. Even for a simple movement of, e.g., the arm seen in a sagittal view, the obtained movements, and therefore the needed forces, are evaluated as rather different, with different criteria. This observation is independent of whether the muscular forces are seen as a redundant set of individual forces, or are summed to resultant acting moments at the considered joints. The paper will describe the developed algorithm, the studied optimization criteria, and the conclusions from a set of examples concerned with bio-mechanical targeted movement.
References [1] A. Eriksson, Analysis methodology based on temporal FEM for bio-mechanical simulations. In: M. Ursino, C. A. Brebbia, G. Pontrelli, E. Magosso (Eds.), Modelling in Medicine and Biology VI, WIT Press, Southampton, 2005. [2] A. Eriksson, Temporal finite elements for target control dynamics of mechanisms, Comp. Struct., 2005 (submitted). [3] T. Flash, N. Hogan, The coordination of arm movements: an experimentally confirmed mathematical model, J. Neurosci. 5, 1688–1703, 1985.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
184
Persistence of Axial Rotation in Idiopathic Scoliosis Due to the Structural Changes of the Intervertebral Disc Behnam Heidari*, David FitzPatrick*, Damien McCormack†, Keith Synnott † *
School of Electrical, Electronic & Mechanical Engineering, University College Dublin, Dublin, Ireland [email protected] †
National Spinal Centre, Mater Misericordiae Hospital, Dublin, Ireland
ABSTRACT There is some research about the morphological changes, spinal instability and causal factors influencing the mechanism of idiopathic scoliosis, however, there remains some controversy about its aetiology and pathogenesis [1,2] and complementary research is required to better identify the causal factors and pathologic mechanism(s) involved in the initiation and development of idiopathic scoliotic deformities of spine. In this study, a validated three-dimensional, anatomically accurate, mathematical model of the mid-thoracic motion segment (T7-T8), which consists of all bony element, soft tissues and articular contact surfaces is utilized, enabling investigation the influence of collagen deficiency in the initiation and progression of idiopathic scoliosis deformity. Alteration in the structure of the intervertebral disc is applied to the model and the resulting geometrical changes together with the coupling behaviour are computed. The results of the model demonstrate the significance of annulus fibrosus collagen fibre imbalance in developing a rotational effect in a motion segment, such as occurs in spinal deformities of idiopathic scoliosis. The structural changes of the annulus fibrosus alter the load displacement pattern of the motion segment and substantially provide the spine with a pattern of deformity under various loading conditions. It is observed that the subtle change in the pattern of collagen network structure results in a flexional rotation (coupled rotational and lateral displacements) due to the involvement of the posterior elements of the thoracic spine particularly during axial rotation. This continuous coupling effect, mainly flexional rotation can, in the long term, cause the morphological changes of the spine with characteristics of scoliotic deformity (axial rotation and lateral bending). The enhanced knowledge of aetiology of the idiopathic scoliosis, throughout understanding the functional characteristics of the annulus fibrosus and articular facets of the thoracic spine, together with the underlying clinical biomechanics and deformation mechanisms, may result in improved treatment of the spinal deformity through less invasive means.
References [1] Ahn U.M., et al., The etiology of adolescent idiopathic scoliosis. Am J Orthop. 31(7), 387-395, 2002. [2] Roberts S., et al., Structure and composition of the cartilage endplates and intervertebral disc in scoliosis. In: Etiology of Adolescent Idiopathic Scoliosis: Current Trends and Relevance to New Treatment Approaches. Hanley and Belfus Inc., Philadelphia, 2000.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
185
Numerical Simulation of Hemodynamics in a Cerebral Artery Iwase, H., Himeno, R. RIKEN 2-1, Hirosawa Wako-city, Saitama, 351-0198, JAPAN {iwase、himeno}@riken.jp
ABSTRACT We have developed the simulation system of hemodynamcs based on voxel model method for modeling and the new developed VOF-VOF corresponding to voxel model for the purpose of advance medical surgery. In image-based simulations, the pre-working such as the modelings of blood vessels and mesh generation require many cost, labour and time. To solve these problems, we adopted voxel mode which is constructed from medical image obtained from MRI, CT. Furthermore, the input system has been developed to efficiently input boundary conditions and calculation conditions. This system makes it possible for users to input boundary conditions and calculation conditions, confirming the location of a boundary to be set through the friendly interface. We examined the precise of simulation system of hemodynamics in the case of the linear-tube. The numerical results were in agreement with theory solutions. As an example of hemodynamics simulation, we handled the blood flow in a cerebral artery with large scale problem. Our developed system could succeed in performing the simulation of hemodynamics. Our developed system enables users to reduce the cost and time on total simulation process. Particularly, the cost and time of modeling and mesh generation are drastically decreased by adopting voxel model method and our developed new scheme. Input system of boundary conditions permits user to smoothly define the boundary conditions through the friendly interface, resulting in the reduction of the load of input boundary conditions.
References [1]C.A. Taylor, M.T. Draney, J.P. Ku, D. Parker, N. Steele, K. Wang, C.K. Zaris, Predictive medicine:Computational Techniques in Therapeutic Decision-Making. Computer Aided Surgery, 4, 231-247, 1999. [2]J.R. Cerebral, P.J. Yim, R. Lohner, O. Soto, P.L. Choyke, Blood flow modeling in carotid arteries using computational fluid dynamics and magneitc resonance imaging, Academic Radiology, 9, 1286-1299, 2002.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
186
Analysis of some Contact Problems in Human Joints after Arthroplasty 2 ´ A. John1, M. Mazdziarz , J. Rojek2 , J.J.Telega 2 , P. Małdyk3 1 Faculty
2
of Mechanical Engineering,Silesian Technical University,Gliwice,Poland [email protected] Institute of Fundamental Technological Research,Warsaw,Poland [email protected] 3 Institute
of Rheumatology,Warsaw,Poland [email protected] ABSTRACT
A general anisotropic model of unilateral contact with adhesion and friction is proposed. The model is applied to the numerical analysis of contact between pelvis and acetabulum after arthroplasty. Clinical evidence confirms the role of not only friction but also of adhesion at the bone-implant interface. We have elaborated a general model of unilateral contact with friction and adhesion applicable to the study of such an interface. Numerical implementation has been performed using the finite element method preceded by a regularization of unilateral conditions. Numerical solutions pertain to the development of zone of adhesion loss. For a discussion of phenomena occurring at the bone-implant interface see [1, 2] The performed numerical analysis pertains to the case of isotropy of bone adhesion but the general anisotropic model presented here can also be used. Also, our approach applies to any joint after arthroplasty and fixation with or without bone cement. Also, one may envisage applications to dental biomechanics. According to clinical data failure of the hip prosthesis is mainly caused by loosening of the acetabulum and not the stem. Surprisingly, in the relevant biomechanical literature not the acetabulum but stem loosening is most often analyzed. Hence the importance of study like the one performed in this paper. Our next goal is to take into account the influence of wear debris, on prostheses loosening. To this end the model proposed by Shillor et al. [3] will be generalized. Acknowledgment: The authors were supported by the Ministry of Science and Information Technology through the grant No. 4 T11F 003 25.
References [1] Rojek J., Telega J.J. (2001) Contact problems with friction, adhesion and wear in orthopaedic biomechanics. Part I: General developments. J. Theor. Appl. Mech. 39:655-677 [2] Rojek J., Telega J.J., Stupkiewicz S. (2001) Contact problems with friction, adhesion and wear in orthopaedic biomechanics. Part II: Numerical implementation and application to implanted knee joints. J. Theor. Appl. Mech. 39:679-706 [3] Shillor M., Sofonea M., Telega J.J. (2003) Analysis of viscoelastic contact with normal compliance, friction and wear diffusion. C.R. Mecanique 331: 395-400 [4] John A. (2004) Identification and analysis of geometrical and mechanical parameters of human pelvis bone Habilitation thesis, in Polish, Silesian Technical University
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
187
Cardiovascular Disease Diagnosis Before Birth by Means of Chaotic Analysis on the Herat Rate Signal Pardis Khayyer*, Alireza Zolghadrasli*, Farhang Daneshmand† and Ali Najafi† *
†
Department of EE, Shiraz University Shiraz, 71345, Iran [email protected]
Department of Mechanical Engineering, Shiraz University Shiraz, 71345, Iran [email protected]
ABSTRACT The heart rate signal contains information about the condition of the heart [1]. One of the features which information can be obtained from the heart rate signal is its chaotic behavior and it may be useful in disease diagnosis of the heart. It is known that a healthy heart, like many other biological systems, has chaotic behavior. This fact is also manifest in the heart rate signal [2]. Among all heart related problems, one of the major problems, facing doctors, has always been the heart related diseases which happen before birth and are not accurately diagnosed until after the birth. Sooner diagnosis will definitely lead to better decision making by doctors. In the present research study, the main purpose is introducing a method for disease diagnosis of fetus before birth. In the procedure of the present research, first the data should be obtained from the heart rate signal and second, the analysis on the signal should be done. Through our work the chaotic analysis are done by means of Matlab programming based on Box Dimension method which is a sub method of fractal dimension and also analysis based on Lyapunov Exponent. A mathematical introduction to Fractal Dimension and Lyapunov exponent is also given in the main paper.
References [1] A. L. Goldberger and et.al. . Fractal dynamics in physiology: Alterations with disease and aging. Colloquium, 99, 2466-2472, 2002. [2] G. Sugihora, W. Allan, D. Sobel and K. D. Allan, Nonlinear control of heart rate variability in human infants. Medical Sciences, 93, 2608-2613, 1996.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
188
Configurational Derivative as a Tool for Image Segmentation ´ A. Feij´oo∗, Edgardo Taroco∗, Andr´e A. Novotny∗ Ignacio Larrabide∗, Raul ∗ Laboratório Nacional de Computação Científica - LNCC
{nacho, feij, etam, novotny}@lncc.br ABSTRACT The introduction to medicine of techniques coming from areas like Computational Fluid Dynamics, Structural Analysis, and Inverse Problems, made the use of imaging data such us Computed Tomography (CT), Magnetic Resonance Imaging (MRI), Single Photon Emission Tomography (SPECT), Positron Emission Tomography (PET) and Ultrasound (US) mandatory in order to apply this techniques to patient specific data. The process of identification of different tissues and organs, called segmentation, is a maior concern in this analysis. This process can be tedious and time consuming when done by hand, so its been an early concern in image processing to automatize it. Many contributions have been made to the area since the introduction of the Mumford and Shah functional. This functional is endowed to quantify the cost associated to a specific segmentation. Our aim in this paper is to present an image segmentation method based on the configurational derivative of the cost functional F endowed to the image data. The configurational derivative can be viewed as an extension of the well established concept of topological derivative when, instead of a hole, a small inclusion is introduced at a point in the domain. More specifically, for an appropriate functional F(u, v) where u is the given image data, a segmentation algorithm is proposed with the following objective: find the segmented image v that minimizes F. Finally, some results are presented in order to show the computational performance of this methodology.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
189
Numerical Simulations to Analyze and Optimize the Human Substitute Voice G. Link, M. Kaltenbacher, R. Lerch Department of Sensor Technology University of Erlangen-N¨urnberg Paul-Gordan-Str. 3/5, 91054 Erlangen, Germany [email protected]
ABSTRACT After a larynx excision, as consequence of e.g. laryngeal cancer, the base of the human voice gets lost and a substitute voice is needed to communicate. A possible base of such a substitute voice represents the upper part of the esophagus, called the pharyngeal-esopohageal segment (PE segment). Via a valve, which the surgeon places between the esophagus and the trachea, the patient can guide air from the trachea into the esophagus. By virtue of that air stream the PE segment starts to vibrate and sound is generated, which can be used as base of a substitute voice. The geometry of this PE segment has major influence on the engaging voice quality. During surgery the surgeon is able to form the geometry of this PE segment. But until now the surgeon has no precise guidelines or knowledge of how to shape it in an optimal way. The target of this project is therefore to built a simulation tool which is capable to value different PE segment geometries in order to improve the quality of the substitute voice. Within this contribution the mathematical models of the involved physical fields as well as their interactions will be discussed. The arising partial differential equations will be solved by using the finite element method (FEM). For the fluid field the weighted least-squares method (LSFEM) and for the mechanical field the Galerkin method is applied. The numerical schemes are finally used to perform a geometry variation of the PE segment. Three different geometries of the PE segment opening (pseudo glottis) -a round, an elliptic and a triangularare compared with each other in respect to their dynamical behavior under fluid loads.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
190
The thaw time of frozen cancellous bone for mechanical testing C. Nabais*, R.M. Guedes†, J.A. Simões† *
Instituto de Engenharia Mecânica e Gestão Industrial Rua do Barroco 174, 4465-591 Leça do Balio, Portugal [email protected] †
Departamento de Engenharia Mecânica e Gestão Industrial, FEUP Rua Dr. Roberto Frias s/n, 4200-465 Porto, Portugal [email protected]
†
Departamento de Engenharia Mecânica da Universidade de Aveiro 3850-193 Aveiro, Portugal [email protected]
ABSTRACT The objective of this study was to estimate the temperature profile at the centre of bovine cancellous bone specimens in order to establish the thaw time prior to testing. We assumed that the heat transfer mechanism inside the cancellous bone specimen is mainly of conduction nature. The thermal properties of bone (i.e. thermal conductivity and specific heat) and its density were assumed constant, over time and temperature. It was verified that thawing is a very fast phenomenon and the theoretical model proved to be accurate enough. Given the experimental results, we conclude that it is reasonable to thaw the specimens 1 hour prior to their use in testing.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
191
Modeling of Passive Behavior of Soft Tissues Including Viscosity and Damage Tobias Olsson∗, Jo˜ao A. C. Martins † ∗ Department of Mechanical Engineering
Link¨opings universitet, SE–581 83 Link¨oping, Sweden. [email protected] †Departamento de Engenharia Civil e Arquitectura e I.C.I.S.T.
Instituto Superior T´ecnico, 1049–001, Lisboa, Portugal. [email protected]
ABSTRACT The mechanical properties of soft tissues depend strongly on the orientation of their fibers, and usually they have a highly nonlinear behavior: their stiffness increases as they are stretched. We are interested here in the passive behavior of soft tissues, when subjected to significant stretches, possibly leading to damage. In this paper we develop a model for a transversely isotropic material that has a damageable viscoelastic behavior. This model is then used to simulate the damage evolution of the tissue. The model is developed with the underlying framework of hyperelasticity, and the corresponding strain energy has different parts associated to different contributions to the material behavior: volumetric, isotropic, anisotropic and dissipative contributions. Since soft tissues are almost incompressible we use a multiplicative split of the deformation gradient into a volume preserving part and a part with (small) volume changes. The anisotropic behavior is characterized by the existence of a family of fiber directions within the tissue. The viscoelastic behavior associated with the non–equilibrium stress is treated as a standard solid material with M Maxwell elements simulating the fact that the response of soft tissues is almost independent of the loading frequency. The total damage is modeled by splitting the energy degradation into one isotropic part and one anisotropic part. That is, we can have fiber degradation independently of the damage of the surrounding matrix. The model is implemented in the commercial Finite element software ABAQUS and the tissue behavior is described by an user subroutine (UMAT). Qualitative features of the model are illustrated and discussed.
References [1] G. A. Holzapfel and T. Gasser, A viscoelastic model for fiber–reinforced composites at finite strains: Continuum basis, computational aspects and applications, Computer Methods in Applied Mechanics and Engineering. 190, 4379–4430, 2001. [2] A. N. Natali et al, Anisotropic elastodamage constitutive model for the biomechanical analysis of tendons, Medical Engineering and Physics, 27, 209–214, 2005.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
192
Nano and macro structure of cortical bone: numerical investigations M. Racila*,†, J. M. Crolet* *
University of Franche-Comté, Besançon, France 16 Route de Gray, 25000, Besançon [email protected] [email protected] †
University of Craiova, Romania 13 A. I. Cuza, Craiova, Romania
ABSTRACT Our last studies proposed a model of cortical bone [1, 2] with five architectural levels macroscopic, osteonal, lamellar, fibrous and fibrillar. In order to take into account the complex process of mineralisation, a new entity has been introduced, the EVMC (Elementary Volume of Mineral Content), which is made by hydroxyapatite cristals and fluid containing mineral ions. Each cristal is made on a solid part and on surounding gel. The modeling of the EVMC architecture is very important for the construction of bony properties at each level of its architecture and of course at the macroscopic level. In this paper, investigations are pursued on the possible geometrical organisation of these EVMC and their elastic properties are computed. Model is made by taking successively into account spatial organization of hydroxyapatite crystals, different mineralizations, a new behaviour’s law, motion of fluid containing ions in each of architectural levels and homogenization of complex composite structures (lamellae, osteons, and cortical bone). On a mathematically point of view, asymptotic developments method in a new piezoelectric framework (with threshold) is used. Developed computational methods have been packed into the software called SiNuPrOs (Numerical Simulations of Cortical Bone’s Properties). On a biomechanical point of view, it has been established that human cortical bone is a non piezoelectric orthotropic medium for which anisotropy is essentially involved by the nanoscopic architecture. For a given organisation of EVMC, mechanical properties are found at macroscopic level and under a standard loading, the obtained mechanical fields induce nanoscopic fields (strain, stress, electrical potentiel) in these EVMC. This process could be seen as an iterative process or a feedback phenomenon and represents an interesting approach of bone remodeling.
References [1] Racila M., Crolet J. M., "Human cortical bone: A tool for numerical simulation of fluid motion in osteonal architectures", Proceedings of 2nd International Conference on Computational Bioengineering, Vol. 2, IST Press, pp. 711-718, 2005 [2] Crolet J. M., Racila M., Mahraoui R., Meunier A., "New numerical concept for hydroxyapatite in human cortical bone", Computer Methods in Biomechanics and Biomedical Engineering, Vol. 8 (2), pp. 139-143, 2005
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
193
Calculation of Muscle and Joint Forces in the Masticatory System Stefan Rues1, Hans J. Schindler1, Karl Schweizerhof 2, Jürgen Lenz1 1
Research Group Biomechanics, University of Karlsruhe Kaiserstraße 12, 76131 Karlsruhe [email protected] 2
Institute for Mechanics, University of Karlsruhe Kaiserstraße 12, 76131 Karlsruhe [email protected]
ABSTRACT The aim of this study was, among other questions, to disclose the direction and magnitude of the forces acting on the condyles of a mandible. The masticatory system is highly redundant, i.e., there are 12 muscle and 2 joint forces in contrast to 6 equilibrium conditions. To reveal the occurring force patterns, in 10 healthy male subjects (31 ± 2.3 yrs.) simultaneous EMG- and force measurements have been performed [1] using surface as well as intramuscular electrodes and a force measuring device. With the help of horizontal and frontal MRTs a 3D-model of the masticatory musculature was generated for each test person. On the basis of these data the lines of action of all muscles were calculated using a) the muscles’ geometry data, i.e., the centroids of origin and insertion areas [2], and b) FE-models based on an appropriate element which reflects the basic behavior of contractile tissue. The FE-models also take into account the muscle architecture (division into tendon and contractile tissue). The force law relating the muscle force to the corresponding electrical activity was determined on the basis of vertical clenching tasks performed at different resultant bite force magnitudes. The experimental results can be well approximated by a second order polynomial. With the knowledge of the lines of action and the force law, the muscle and joint forces can finally be calculated for the tested resultant bite forces.
References [1] H.J. Schindler, S. Rues, J.C. Türp, J. Lenz, Activity patterns of the masticatory muscles during feedback-controlled simulated clenching activities. Eur. J. Oral Sci., 113, 469-478, 2005. [2] T.M.G.J. van Eijden, J.A.M. Korfage, P. Brugman, Architecture of the human jaw-closing and jaw-opening muscles. The Anatomical Record, 248, 464-474, 1997.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
194
The algorithms of mathematical programming in muscle recruitment and muscle wrapping problems V´ıt Vondr´ak∗, John Rasmussen†, Michael Damsgaard‡ and Zdenˇek Dost´al∗ ∗ Technical University of Ostrava 17. listopadu 15, CZ-70833 Ostrava-Poruba, Czech Republic [email protected], [email protected] †Institute of Mechanical Engineering, Aalborg University Pontoppidanstræde 101, DK-9220 Aalborg East, Denmark [email protected] ‡AnyBody Technology A/S Niels Jernes Vej 10, DK-9220 Aalborg East, Denmark [email protected]
ABSTRACT In spite of the enormous variety of life on Earth, muscle work in all animals is accomplished by the same physiological mechanism in which an electro-chemical process causes contraction of muscle tissue. Furthermore, muscle systems across species are equipped with a significant level of redundancy, in the sense that the number of muscles significantly exceeds the number of degrees of freedom of the body. Hence, infinitely many combinations of muscle force can balance the external loads, and selecting the best one is an optimization problem that the central nervous system solves instantly when a certain movement is called for. The mathematical modelling of these optimization processes is of vital importance to our basic understanding of human physiology and planning of surgical procedures, design of prostheses and implants, and planning of rehabilitation procedures. In our presentation, we shall consider in particular optimization problems which carry out muscle recruitment in the inverse dynamic simulations of body movements. Namely, we shall introduce those problems which could be formulated as linear or quadratic programming problems and which could be therefore solved very efficiently. The several different algorithms for the solution of such problems will be presented and results will be compared on model and realistic simulations. Another important part of the muscle recruitment problem is an identification of the path of a muscle which wraps over bones or other tissues. Therefore we will also present a geometric model of a muscle that wraps over a set of obstacles. The muscle is represented by a thin elastic string and the obstacles are represented by rigid surfaces such that the muscle wrapping problem is identified as a contact problem. The finite element (FE) method is used to discretize the string and the FE model is solved iteratively with the efficient scalable FETI based contact solver that was originally proposed for solution of the contact problems of elastic bodies as described in [1]. The several practical models built in AnyBody Modeling System will be presented.
References [1] Z. Dost´al, Inexact semi-monotonic augmented Lagrangians with optimal feasibility convergence for convex bound and equality constrained quadratic programming, SIAM J. Numerical Analysis 43, 1, 96-115, 2005. [2] Anybody Modeling System. http://www.anybodytech.com
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
195
Three-Dimensional Numerical Simulation of Airflow and Vibration Analysis for Upper Airway of Humans Chi Yu *, Yuefang Wang †, Yingxi Liu†, Xiuzhen Sun‡ P
* P
P
P
P
P
P
P
P
State Key Lab. of Struct. Anal. for Ind. Equip., Dalian University of Technology 2 Linggong Road, Dalian 116024, China [email protected] † P
P
Department of Engineering Mechanics, Dalian University of Technology 2 Linggong Road, Dalian 116024, China [email protected]; [email protected] ‡ P
P
Department of Otorhinalaryngology, Dalian Medical University 465 Zhongshan Road, Dalian 116027, China [email protected] P
ABSTRACT Obstructive sleep apnea syndrome (OSAS) may cause apneas or hypopneas, both physically and emotionally harmful to their sufferers. It has been realized that the periodic intermittent cessations of breathing or reductions in airflow resulted from OSAS is closely related to the developed pathological change in upper airways of the patients. In this paper, the authors present numerical simulations of airflows and fluid-solid interaction analysis for human upper airways. The objective of the research is to investigate airfield characteristics of the human upper airway by means of computational fluid dynamics (CFD) and the finite element (FE) method. The authors reconstruct three-dimensional models of the upper airway from the nostril to the epiglottis based on CT scanning images collected from two clinic volunteers. Based on the reconstruction three-dimensional CFD models that precisely preserve original configuration of upper airways are created. The CFD analysis is carried out by the FE method with boundary conditions of pressure at the nostril and of velocity at the top of vocal cord. The non-slip boundary conditions are used on the interior walls of the upper airway. With the CFD results the pressure and velocity distributions in the airflow field are quantitatively determined. For fluid-solid interaction analyses, the upper airway in the vicinity of the pharyngeal cavity is meshed using the reconstructed model. The fluid-solid interactive computations are performed for the healthy person and the OSAS patient. The results show that the hypertrophy of the soft palate remarkably escalates both the pressure and the deformation levels of the upper airway and hinders the airflow in the cavity channels.
References [1] R.J. Schwab and A.N. Goldberg, Upper airway assessment: Radiographic and other imaging techniques. Otolaryngoly-nhol Clin North Am, 31, 931-968, 1998. [2] X.L. Sheng, Pathophysiology and epidemiology of obstructive sleep apnea-hypopnea syndrome. The Journal of Practical Medicine, 21, 1973-1975, 2005. [3] T. Yong, M. Palta, J. Dempsey, et al, The occurrence of sleep disordered breathing among middle-aged adults. N Engl J Med, 328, 1230-1235, 1993.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
196
Computer Simulation of Anisotropic Damage and Residual Stresses in Atherosclerotic Arteries D. Balzani∗, J. Schr¨oder∗, D. Gross† ∗ Institute of Mechanics, Department of Civil Engineering, University of Duisburg-Essen
Universtit¨atsstr. 15, 45117 Essen, Germany [email protected] †Institute of Mechanics, Department of Mechanics, Technical University of Darmstadt
Hochschulstr. 1, 64289 Darmstadt, Germany ABSTRACT The goal of this contribution is to propose a method for the numerical simulation of residual stresses in arterial walls. Generally, when axial segments of arterial walls are sliced in radial direction they spring open, which has been observed firstly in Vaishnav & Vossoughi [1]. Thus, residual stresses have to exist in the unloaded configuration. As often stated in the literature an open artery governed by a radial cut can be assumed to be stress-free. In this contribution we firstly close the gap between the opened transmural surfaces of a sliced artery by a displacement-driven procedure introducing some kind of interface elements formulated in the relative displacement of associated nodal points. Then we construct a new mesh of the closed artery and apply a method to incorporate the residual stresses without using the interface elements. This is advantageous for further numerical simulations as e.g., applying an internal pressure. Due to the special composition, orientation and weak interaction of particular fibers within arterial walls we consider the superposition of two transversely isotropic hyperelastic stored energy functions for the description of the anisotropic hyperelastic behavior in the physiological range of deformations. In order to guarantee the existence of solutions of underlying boundary value problems we use the functions proposed in Balzani, Neff, Schr¨oder & Holzapfel [2], which fit into the concept of polyconvexity. When arteries are overstretched, e.g., during a balloon-angioplasty, then deformations occur which are not in the physiological range anymore, and a discontinuous damage effect is observed. Therefore, the thermodynamically consistent anisotropic damage model introduced in Balzani, Schr¨oder & Gross [3] is applied to the polyconvex stored energy. The basic assumption of the damage model is that the damage occurs mainly in fiber direction. As a numerical example we consider the cross-section of a diseased artery in order to give an impression of the performance of the model.
References [1] R.N. Vaishnav & J. Vossoughi, Estimation of Residual Strains in Aortic Segments, C.W. Hall (Ed.): Biomedial Engineering II: Recent Developments, Pergamon Press, 330–333, 1983 [2] D. Balzani, P. Neff, J. Schr¨oder & G.A. Holzapfel, A Polyconvex Framework for Soft Biological Tissues. Adjustment to Experimental Data, International Journal of Solids and Structures, in press, 2005 [3] D. Balzani, J. Schr¨oder & D. Gross, A Simple Model for Anisotropic Damage with Applications to Soft Tissues, Proceedings in Applied Mathematics and Mechanics, Vol. 4, 236–237, 2004
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
197
Computational study on stability and bone remodeling for a hip replacement using a “minimal invasive” femoral stem João Folgado, Rui P. Andrade, Paulo R. Fernandes IDMEC - IST Av. Rovisco Pais, 1049-001 Lisboa, Portugal [email protected]; [email protected]; [email protected]
ABSTRACT In a total hip artroplasty, femoral head is removed and the stem component is inserted into the femoral canal removing a considerable amount of hosted bone. Recently some manufactures have developed the design of smaller stems for “minimally invasive” hip replacement surgery. These smaller stems require minimal bone removal, leaving intact many elements of fixation that would otherwise be lost in a traditional primary arthroplasty. Furthermore, the maintenance of bone mass is of major importance particularly in the case of a future revision surgery. However, one aspect of major concern with these stems is the fixation and the stability of the stem. Actually, the stability of the stem plays a role in the success of a cementless total hip artroplasty. In order to assure the long term stability, most of the stems are design to promote biologic fixation, i.e, the bone attachment into the stem surface. The osseointegration (or bone ingrowth) is achieved coating the surface with hydroxyapatite (HA) or simply with a porous coated layer. However, even with such a special coated surfaces, several factors can inhibit or destroy the biologic fixation. Among these factors are mechanical ones such as large displacements and high stresses in the bone/implant interface. In this work a computational model is developed to study the osseointegration in a cementless femoral stem. The bone ingrowth process is modeled based on the relative displacement between bone and stem as well as on interface stress level. The biological fixation is not dissociated to the remodeling of surrounded bone due to the stress shield effect. Thus the model combines the osseointegration analysis with a bone remodeling model. The law of bone remodeling is derived from a material optimization problem, via the minimization of a function that takes into account structural stiffness and the metabolic cost related with bone mass maintenance, where bone is modeled as a porous material with variable density. The problem considers contact conditions on the interface between bone and implant. During the remodeling process, the mechanical interface conditions are updated according with the ingrowth algorithm: if the displacement and stress conditions necessaries for bone attachment are satisfied, then a connection between bone and implant is established. Consequently, the bone behavior is fully simulated from the immediate post operative condition until a long term condition. The osseointegration process emphasizes the behavior of the bone/stem interface, addressing the problem of stability of the prosthesis. The model is used to analyzed a “minimal invasive” stem (Mayo, Zimmer Inc.) comparing its performance with a conventional one (Trilock, Depuy Orthopaedics, Johnson&Johnson). Results allow us to validate the computational model and evaluate the performance of these two distinct stems.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
198
Porous polycrystals built up by uniformly and axisymmetrically oriented needles: Homogenization of elastic properties Andreas Fritsch∗ , Luc Dormieux† , Christian Hellmich∗ ∗
Vienna University of Technology (TU Wien), Institute for Mechanics of Materials and Structures Karlsplatz 13/202, A-1040 Wien (Vienna), Austria [email protected], [email protected] † Laboratory
of Materials and Structures, National School of Civil Engineering (ENPC) 6 et 8 Avenue Blaise Pascal, 77455 Marne-la-Vall´ee, France [email protected]
ABSTRACT Porous polycrystal-type microstructures built up of needle-like platelets or sheets are characteristic for a number of biological materials, such as bone [2] or eggs [5]. Herein, we consider (i) uniform, (ii) axisymmetrical orientation distribution of linear elastic, isotropic as well as anisotropic needles. The latter requires derivation of the Hill tensor for arbitrarily oriented ellipsoidal inclusions with one axis tending towards infinity, embedded in a transversely isotropic matrix; this is accomplished by a new semi-analytical technique based on the work of Laws [3]. For a porosity lower 0.4, the elastic properties of the polycrystal with uniformly oriented needles are quasi-identical to those of a polycrystal with solid spheres. However, as opposed to the sphere-based model, the needle-based model does not predict a percolation threshold. As regards axisymmetrical orientation distribution of needles, two effects are remarkable: Firstly, the sharper the cone of orientations the higher the anisotropy of the polycrystal. Secondly, for a given cone, the anisotropy increases with the porosity. These results confirm the very high degree of orientation randomness of crystals [4] building up mineral foams [2, 1] in bone tissues.
References [1] Ch. Hellmich, J.-F. Barth´el´emy, and L. Dormieux. Mineral-collagen interactions in elasticity of bone ultrastructure – a continuum micromechanics approach. European Journal of Mechanics ASolids, 23:783 – 810, 2004. [2] Ch. Hellmich and F.-J. Ulm. Are mineralized tissues open crystal foams reinforced by crosslinked collagen? – some energy arguments. Journal of Biomechanics, 35:1199 – 1212, 2002. [3] N. Laws. The determination of stress and strain concentrations at an ellipsoidal inclusion in an anisotropic material. Journal of Elasticity, 7(1):91 – 97, 1977. [4] F. Peters, K. Schwarz, and M. Epple. The structure of bone studied with synchrotron x-ray diffraction, x-ray absorption spectroscopy and thermal analysis. Thermochimica Acta, 361:131 – 138, 2000. [5] H. Silyn-Roberts and R.M. Sharp. Crystal growth and the role of the organic network in eggshell biomineralization. Proceedings of the Royal Society of London, Series B, 227(1248):303 – 324, 1986.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
199
A Poroviscoelastic Overlay Model for Finite Element Analyses of Articular Cartilage at Large Strains † ¨ Uwe-Jens G¨orke∗ , Hubert Gunther , Markus A. Wimmer‡ ∗
Institute of Mechanics, Chemnitz University of Technology Str. d. Nationen 62, D-09111 Chemnitz, Germany [email protected] † TBZ-Pariv, Chemnitz and AO Research Institute, Davos Liddy-Ebersberger-Str. 41, D-09127 Chemnitz, Germany [email protected]
‡ Department
of Orthopedics, Rush University Medical Center 1653 W. Congress Pkwy, Suite 761, Chicago, IL 60612, USA Markus A [email protected] ABSTRACT
Articular cartilage represents a complex inhomogeneous, multiphase material. Due to its sophisticated structure articular cartilage distinguishes itself by exceptional load-bearing properties under a wide variety of loading conditions. Currently, it is generally recognized that articular cartilage is subjected to large strains under in vivo mechanical conditions, which can be described as a first approximation with nonlinear elastic material models. Furthermore, rate dependent phenomena and osmotic effects caused by the presence of fixed charges can be observed. We propose to model structural effects of articular cartilage load response within the context of a phenomenological biphasic material approach resulting from an overlay concept (cf. [1]). The basic idea of this superposition methodology is the additive decomposition of the stress tensor according to specific mechanical properties whose underlying physics can partly be illustrated on rheological models adapted to large strain conditions (see [2] and others). Recent investigations have shown that due to the varying orientation of the collagen fibers the solid matrix of the cartilage tissue can be considered as an anisotropic hyperelastic material with tensioncompression nonlinearities. Frequently, the rate-dependency of a biphasic material behavior is exclusively attributed to the fluid flow through the solid matrix. However, recent observations demonstrate that viscoelastic properties of the solid phase must not be neglected. Therefore, viscous overstresses have been considered by the authors as well as an osmotic pressure model to simulate swelling states. The theoretical background and the numerical algorithms of all the parts of a suitable material model are presented. This model has been implemented into a commercially available FE-code. Some numerical examples showing several structural effects are discussed within the context of experimental results.
References [1] S. Olsen and A. Oloyede, A Finite Element Analysis Methodology for Representing the Articular Cartilage Functional Structure. Comp. Meth. Biomech. Biomed. Eng., 5(6), 377–386, 2002. [2] A. Lion, On the Large Deformation Behaviour of Reinforced Rubber at different Temperatures. J. Mech. Phys. Solids, 45, 1805–1834, 1997.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
200
A Finite Element Study of Strain Distribution in an Instrumented Knee Prosthesis for Full Force Measurement in Vivo. Rui Guimaraes, Stephen JG Taylor, Gordon W Blunn Centre for Biomedical Engineering, Institute of Orthopaedics and Musculoskeletal Science, (University College London), Brockley Hill, Stanmore HA7 4LP, UK. [email protected], [email protected], [email protected]
ABSTRACT Data on forces applied across joints in the body are needed to know how to better design and test implants, define rehabilitation regimes, and provide basic data for other biomechanics studies. The resultant knee load vector will vary in vivo in magnitude and position due to the joint laxity: the knee has six degrees of freedom and very irregular geometry. The overall aim is to develop an instrumented knee implant that can measure the full force vector (compression, anterio-posterior and medio-lateral shear forces) applied across each compartment of the tibio-femoral joint during activity [1]. Each tibial compartment was hollowed out to allow insertion of electronics and strain gauges, and was enclosed by a solid rim. This rim, although providing good mechanical support, had the effect of cross-coupling the strains around the periphery. A finite element model of the modified tibial tray was developed in order to study the behaviour of strains to applied loads and to determine the optimum locations and angles for the strain gauges in vivo. In this model, single and combination loads were applied to one compartment, inside the gauged periphery, using a modified plastic liner. Twelve strain gauge half bridges (24 sites) were simulated around the compartment periphery, and 3D strains for each found from the FEA. With individually applied axial and shear forces, the strain sensitivity at each of these 24 sites was found for a small range of positions, forming an important base dataset. This dataset was used to develop methods of transforming the measured strains back to the applied loads. The dataset shows a nonlinear, but gentle, variation of load sensitivity with position. Therefore it is possible to use multidimensional interpolation to extend the dataset with little loss of accuracy. With this extended dataset, algorithms were tested to assess how accurately the loads and positions could be calculated. The general procedure was to derive force/strain sensitivity matrices, using the 12 half bridge strains, for many different calibration positions, and to use a least squares minimisation method to determine the closest match between calibration and input data. This technique quickly iterates to the correct positions and axial force if the shear forces are low, and the remaining challenge is to predict the positions and shear forces together, and this is now the focus of our analysis. Using FEA it was possible to verify the design of the implant structurally and devise methods for determining the axial force and both antero-posterior (A-P) and medio-lateral (M-L) shear force magnitudes, and the point of application of those forces in each separate knee compartment.
Reference SJG Taylor, J Gorjon, A Gorjon. Development of an instrumented tibial tray for knee force measurement in vivo. Proc. 12th Conf. European Society of Biomechanics, Dublin, p110, 2000.
[1]
Acknowledgement: This work was funded by the EPSRC.
III European Conference on Computational Mechanics Solids, Structures and Coupled Problems in Engineering C.A. Mota Soares et al. (eds.) Lisbon, Portugal, 5–8 June 2006
201
Topological Derivative Applied to Image Enhancement ´ A. Feij´oo∗ , Edgardo Taroco∗ , Andr´e A. Novotny∗ Ignacio Larrabide∗ , Raul ∗ Laborat´ orio
Nacional de Computac¸a˜ o Cient´ıfica - LNCC nacho, feij, etam, [email protected]
ABSTRACT Medical imaging techniques like Computed Tomography (CT), Magnetic Resonance Imaging (MRI), Single Photon Emission Tomography (SPECT), Positron Emission Tomography (PET) and Ultrasound (US) have introduced a formidably powerful tool in medicine. The poor quality or high signal-to-noise ratio (SNR) of this kind of images is maior limitation for image analysis. For this reason image enhancement takes an important roll in the segmentation and analysis process. Although imaging techniques (e.g., contrast agents, biological markers) should improve the image quality this is not always enough to give a good result. Much effort has been put into the area of image enhancement. Our aim in this paper is to present a method for medical image enhancement based on the well established concept of topological sensitivity analysis and borrowing image processing techniques like anisotropic diffusion. More specifically, an appropriate functional F is associated to the image indicating the cost endowed to an specific image. Let us assume that the image being segmented is characterized by a scalar field u representing the image data. Then, the segmentation algorithm can be cast as: given the evolution equation, ∂u = div(k∇u), (1) ∂t find u such that minimizes the functional F(k, u). This functional is associated to an energy norm of the imag