Roark’s Formulas for Stress and Strain WARREN C. YOUNG RICHARD G. BUDYNAS
Seventh Edition
McGraw-Hill New York Chicag...
327 downloads
2575 Views
6MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
Roark’s Formulas for Stress and Strain WARREN C. YOUNG RICHARD G. BUDYNAS
Seventh Edition
McGraw-Hill New York Chicago San Francisco Lisbon London Madrid Mexico City Milan New Delhi San Juan Seoul Singapore Sydney Toronto
Cataloging-in-Publication Data is on file with the Library of Congress.
Copyright # 2002, 1989 by the McGraw-Hill Companies, Inc. All rights reserved. Printed in the United States of America. Except as permitted under the United States Copyright Act of 1976, no part of this publication may be reproduced or distributed in any form or by any means, or stored in a data base or retrieval system, without the prior written permission of the publisher. 123456789
DOC=DOC
07654321
ISBN 0-07-072542-X The sponsoring editor for this book was Larry Hager and the production supervisor was Pamela A. Pelton. It was set in Century Schoolbook by Techset Composition Limited. Printed and bound by R. R. Donnelley & Sons Company.
McGraw-Hill books are available at special quantity discounts to use as premiums and sales promotions, or for use in corporate training programs. For more information, please write to the Director of Special Sales, Professional Publishing, McGraw-Hill, Two Penn Plaza, New York, NY 10121-2298. Or contact your local bookstore.
This book is printed on recycled, acid-free paper containing a minimum of 50% recycled, de-inked fiber.
Information contained in this work has been obtained by The McGraw-Hill Companies, Inc. (‘‘McGraw-Hill’’) from sources believed to be reliable. However, neither McGraw-Hill nor its authors guarantee the accuracy or completeness of any information published herein and neither McGraw-Hill nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that McGrawHill and its authors are supplying information but are not attempting to render engineering or other professional services. If such services are required, the assistance of an appropriate professional should be sought.
Contents
List of Tables
vii
Preface to the Seventh Edition ix Preface to the First Edition
xi
Part 1 Introduction Chapter 1
Introduction
3
Terminology. State Properties, Units, and Conversions. Contents.
Part 2 Facts; Principles; Methods Chapter 2
Stress and Strain: Important Relationships
9
Stress. Strain and the Stress–Strain Relations. Stress Transformations. Strain Transformations. Tables. References.
Chapter 3
The Behavior of Bodies under Stress
35
Methods of Loading. Elasticity; Proportionality of Stress and Strain. Factors Affecting Elastic Properties. Load–Deformation Relation for a Body. Plasticity. Creep and Rupture under Long-Time Loading. Criteria of Elastic Failure and of Rupture. Fatigue. Brittle Fracture. Stress Concentration. Effect of Form and Scale on Strength; Rupture Factor. Prestressing. Elastic Stability. References.
Chapter 4
Principles and Analytical Methods
63
Equations of Motion and of Equilibrium. Principle of Superposition. Principle of Reciprocal Deflections. Method of Consistent Deformations (Strain Compatibility). Principles and Methods Involving Strain Energy. Dimensional Analysis. Remarks on the Use of Formulas. References. iii
iv
Contents
Chapter 5
Numerical Methods
73
The Finite-Difference Method. The Finite-Element Method. The BoundaryElement Method. References.
Chapter 6
Experimental Methods
81
Measurement Techniques. Electrical Resistance Strain Gages. Detection of Plastic Yielding. Analogies. Tables. References.
Part 3 Formulas and Examples Chapter 7
Tension, Compression, Shear, and Combined Stress
109
Bar under Axial Tension (or Compression); Common Case. Bar under Axial Tension (or Compression); Special Cases. Composite Members. Trusses. Body under Pure Shear Stress. Cases of Direct Shear Loading. Combined Stress.
Chapter 8
Beams; Flexure of Straight Bars
125
Straight Beams (Common Case) Elastically Stressed. Composite Beams and Bimetallic Strips. Three-Moment Equation. Rigid Frames. Beams on Elastic Foundations. Deformation due to the Elasticity of Fixed Supports. Beams under Simultaneous Axial and Transverse Loading. Beams of Variable Section. Slotted Beams. Beams of Relatively Great Depth. Beams of Relatively Great Width. Beams with Wide Flanges; Shear Lag. Beams with Very Thin Webs. Beams Not Loaded in Plane of Symmetry. Flexural Center. Straight Uniform Beams (Common Case). Ultimate Strength. Plastic, or Ultimate Strength. Design. Tables. References.
Chapter 9
Bending of Curved Beams
267
Bending in the Plane of the Curve. Deflection of Curved Beams. Circular Rings and Arches. Elliptical Rings. Curved Beams Loaded Normal to Plane of Curvature. Tables. References.
Chapter 10
Torsion
381
Straight Bars of Uniform Circular Section under Pure Torsion. Bars of Noncircular Uniform Section under Pure Torsion. Effect of End Constraint. Effect of Longitudinal Stresses. Ultimate Strength of Bars in Torsion. Torsion of Curved Bars. Helical Springs. Tables. References.
Chapter 11
Flat Plates
Common Case. Bending of Uniform-Thickness Plates with Circular Boundaries. Circular-Plate Deflection due to Shear. Bimetallic Plates. Nonuniform Loading of Circular Plates. Circular Plates on Elastic Foundations. Circular Plates of Variable Thickness. Disk Springs. Narrow Ring under Distributed Torque about Its Axis. Bending of UniformThickness Plates with Straight Boundaries. Effect of Large Deflection. Diaphragm Stresses. Plastic Analysis of Plates. Ultimate Strength. Tables. References.
427
Contents
Chapter 12
Columns and Other Compression Members
v
525
Columns. Common Case. Local Buckling. Strength of Latticed Columns. Eccentric Loading: Initial Curvature. Columns under Combined Compression and Bending. Thin Plates with Stiffeners. Short Prisms under Eccentric Loading. Table. References.
Chapter 13
Shells of Revolution; Pressure Vessels; Pipes
553
Circumstances and General State of Stress. Thin Shells of Revolution under Distributed Loadings Producing Membrane Stresses Only. Thin Shells of Revolution under Concentrated or Discontinuous Loadings Producing Bending and Membrane Stresses. Thin Multielement Shells of Revolution. Thin Shells of Revolution under External Pressure. Thick Shells of Revolution. Tables. References.
Chapter 14
Bodies in Contact Undergoing Direct Bearing and Shear Stress
689
Stress due to Pressure between Elastic Bodies. Rivets and Riveted Joints. Miscellaneous Cases. Tables. References.
Chapter 15
Elastic Stability
709
General Considerations. Buckling of Bars. Buckling of Flat and Curved Plates. Buckling of Shells. Tables. References.
Chapter 16
Dynamic and Temperature Stresses
743
Dynamic Loading. General Conditions. Body in a Known State of Motion. Impact and Sudden Loading. Approximate Formulas. Remarks on Stress due to Impact. Temperature Stresses. Table. References.
Chapter 17
Stress Concentration Factors
771
Static Stress and Strain Concentration Factors. Stress Concentration Reduction Methods. Table. References.
Appendix A
Properties of a Plane Area
799
Appendix B
Glossary: Definitions
813
Appendix C
Composite Materials
827
Table.
Composite Materials. Laminated Composite Materials. Laminated Composite Structures.
Index
841
List of Tables
1.1 1.2 1.3 2.1 2.2 2.3 5.1 6.1 6.2 8.1 8.2 8.3 8.4 8.5 8.6 8.7a 8.7b 8.7c 8.7d 8.8 8.9 8.10 8.11a 8.11b 8.11c 8.11d 8.12 8.13 9.1 9.2 9.3
Units Appropriate to Structural Analysis Common Prefixes Multiplication Factors to Convert from USCU Units to SI Units Material Properties Transformation Matrices for Positive Rotations about an Axis Transformation Equations Sample Finite Element Library Strain Gage Rosette Equations Applied to a Specimen of a Linear, Isotropic Material Corrections for the Transverse Sensitivity of Electrical Resistance Strain Gages Shear, Moment, Slope, and Deflection Formulas for Elastic Straight Beams Reaction and Deflection Formulas for In-Plane Loading of Elastic Frames Numerical Values for Functions Used in Table 8.2 Numerical Values for Denominators Used in Table 8.2 Shear, Moment, Slope, and Deflection Formulas for Finite-Length Beams on Elastic Foundations Shear, Moment, Slope, and Deflection Formulas for Semi-Infinite Beams on Elastic Foundations Reaction and Deflection Coefficients for Beams under Simultaneous Axial and Transverse Loading: Cantilever End Support Reaction and Deflection Coefficients for Beams under Simultaneous Axial and Transverse Loading: Simply Supported Ends Reaction and Deflection Coefficients for Beams under Simultaneous Axial and Transverse Loading: Left End Simply Supported, Right End Fixed Reaction and Deflection Coefficients for Beams under Simultaneous Axial and Transverse Loading: Fixed Ends Shear, Moment, Slope, and Deflection Formulas for Beams under Simultaneous Axial Compression and Transverse Loading Shear, Moment, Slope, and Deflection Formulas for Beams under Simultaneous Axial Tension and Transverse Loading Beams Restrained against Horizontal Displacement at the Ends Reaction and Deflection Coefficients for Tapered Beams; Moments of Inertia Vary as ð1 þ Kx =lÞn , where n ¼ 1:0 Reaction and Deflection Coefficients for Tapered Beams; Moments of Inertia Vary as ð1 þ Kx =lÞn , where n ¼ 2:0 Reaction and Deflection Coefficients for Tapered Beams; Moments of Inertia Vary as ð1 þ Kx =lÞn , where n ¼ 3:0 Reaction and Deflection Coefficients for Tapered Beams; Moments of Inertia Vary as ð1 þ Kx =lÞn , where n ¼ 4:0 Position of Flexural Center Q for Different Sections Collapse Loads with Plastic Hinge Locations for Straight Beams Formulas for Curved Beams Subjected to Bending in the Plane of the Curve Formulas for Circular Rings Reaction and Deformation Formulas for Circular Arches
4 5 5 33 33 34 76 102 104 189 202 211 212 213 221 225 226 227 228 229 242 245 246 249 252 255 258 260 304 313 333
vii
viii 9.4 10.1 10.2 10.3 11.1 11.2 11.3 11.4 12.1 13.1 13.2 13.3 13.4 13.5 14.1 15.1 15.2 16.1 17.1 A.1 C.1
List of Tables Formulas for Curved Beams of Compact Cross-Section Loaded Normal to the Plane of Curvature Formulas for Torsional Deformation and Stress Formulas for Torsional Properties and Stresses in Thin-Walled Open Cross-Sections Formulas for the Elastic Deformations of Uniform Thin-Walled Open Members under Torsional Loading Numerical Values for Functions Used in Table 11.2 Formulas for Flat Circular Plates of Constant Thickness Shear Deflections for Flat Circular Plates of Constant Thickness Formulas for Flat Plates with Straight Boundaries and Constant Thickness Formulas for Short Prisms Loaded Eccentrically; Stress Reversal Impossible Formulas for Membrane Stresses and Deformations in Thin-Walled Pressure Vessels Shear, Moment, Slope, and Deflection Formulas for Long and Short Thin-Walled Cylindrical Shells under Axisymmetric Loading Formulas for Bending and Membrane Stresses and Deformations in Thin- Walled Pressure Vessels Formulas for Discontinuity Stresses and Deformations at the Junctions of Shells and Plates Formulas for Thick-Walled Vessels Under Internal and External Loading Formulas for Stress and Strain Due to Pressure on or between Elastic Bodies Formulas for Elastic Stability of Bars, Rings, and Beams Formulas for Elastic Stability of Plates and Shells Natural Frequencies of Vibration for Continuous Members Stress Concentration Factors for Elastic Stress (K t) Properties of Sections Composite Material Systems
350 401 413 417 455 457 500 502 548 592 601 608 638 683 702 718 730 765 781 802 830
Preface to the Seventh Edition
The tabular format used in the fifth and sixth editions is continued in this edition. This format has been particularly successful when implementing problem solutions on a programmable calculator, or especially, a personal computer. In addition, though not required in utilizing this book, user-friendly computer software designed to employ the format of the tabulations contained herein are available. The seventh edition intermixes International System of Units (SI) and United States Customary Units (USCU) in presenting example problems. Tabulated coefficients are in dimensionless form for convenience in using either system of units. Design formulas drawn from works published in the past remain in the system of units originally published or quoted. Much of the changes of the seventh edition are organizational, such as: j
Numbering of equations, figures and tables is linked to the particular chapter where they appear. In the case of equations, the section number is also indicated, making it convenient to locate the equation, since section numbers are indicated at the top of each odd-numbered page.
j
In prior editions, tables were interspersed within the text of each chapter. This made it difficult to locate a particular table and disturbed the flow of the text presentation. In this edition, all numbered tables are listed at the end of each chapter before the references.
Other changes=additions included in the seventh addition are as follows: j
Part 1 is an introduction, where Chapter 1 provides terminology such as state properties, units and conversions, and a description of the contents of the remaining chapters and appendices. The definiix
x
Preface to the Seventh Edition
tions incorporated in Part 1 of the previous editions are retained in the seventh edition, and are found in Appendix B as a glossary. j
Properties of plane areas are located in Appendix A.
j
Composite material coverage is expanded, where an introductory discussion is provided in Appendix C, which presents the nomenclature associated with composite materials and how available computer software can be employed in conjunction with the tables contained within this book.
j
Stress concentrations are presented in Chapter 17.
j
Part 2, Chapter 2, is completely revised, providing a more comprehensive and modern presentation of stress and strain transformations.
j
Experimental Methods. Chapter 6, is expanded, presenting more coverage on electrical strain gages and providing tables of equations for commonly used strain gage rosettes.
j
Correction terms for multielement shells of revolution were presented in the sixth edition. Additional information is provided in Chapter 13 of this edition to assist users in the application of these corrections.
The authors wish to acknowledge and convey their appreciation to those individuals, publishers, institutions, and corporations who have generously given permission to use material in this and previous editions. Special recognition goes to Barry J. Berenberg and Universal Technical Systems, Inc. who provided the presentation on composite materials in Appendix C, and Dr. Marietta Scanlon for her review of this work. Finally, the authors would especially like to thank the many dedicated readers and users of Roark’s Formulas for Stress & Strain. It is an honor and quite gratifying to correspond with the many individuals who call attention to errors and=or convey useful and practical suggestions to incorporate in future editions. Warren C. Young Richard G. Budynas
Preface to the First Edition
This book was written for the purpose of making available a compact, adequate summary of the formulas, facts, and principles pertaining to strength of materials. It is intended primarily as a reference book and represents an attempt to meet what is believed to be a present need of the designing engineer. This need results from the necessity for more accurate methods of stress analysis imposed by the trend of engineering practice. That trend is toward greater speed and complexity of machinery, greater size and diversity of structures, and greater economy and refinement of design. In consequence of such developments, familiar problems, for which approximate solutions were formerly considered adequate, are now frequently found to require more precise treatment, and many less familiar problems, once of academic interest only, have become of great practical importance. The solutions and data desired are often to be found only in advanced treatises or scattered through an extensive literature, and the results are not always presented in such form as to be suited to the requirements of the engineer. To bring together as much of this material as is likely to prove generally useful and to present it in convenient form has been the author’s aim. The scope and management of the book are indicated by the Contents. In Part 1 are defined all terms whose exact meaning might otherwise not be clear. In Part 2 certain useful general principles are stated; analytical and experimental methods of stress analysis are briefly described, and information concerning the behavior of material under stress is given. In Part 3 the behavior of structural elements under various conditions of loading is discussed, and extensive tables of formulas for the calculation of stress, strain, and strength are given. Because they are not believed to serve the purpose of this book, derivations of formulas and detailed explanations, such as are appropriate in a textbook, are omitted, but a sufficient number of examples
xi
xii
Preface to the First Edition
are included to illustrate the application of the various formulas and methods. Numerous references to more detailed discussions are given, but for the most part these are limited to sources that are generally available and no attempt has been made to compile an exhaustive bibliography. That such a book as this derives almost wholly from the work of others is self-evident, and it is the author’s hope that due acknowledgment has been made of the immediate sources of all material here presented. To the publishers and others who have generously permitted the use of material, he wishes to express his thanks. The helpful criticisms and suggestions of his colleagues, Professors E. R. Maurer, M. O. Withey, J. B. Kommers, and K. F. Wendt, are gratefully acknowledged. A considerable number of the tables of formulas have been published from time to time in Product Engineering, and the opportunity thus afforded for criticism and study of arrangement has been of great advantage. Finally, it should be said that, although every care has been taken to avoid errors, it would be oversanguine to hope that none had escaped detection; for any suggestions that readers may make concerning needed corrections the author will be grateful. Raymond J. Roark
Part
1 Introduction
Chapter
1 Introduction
The widespread use of personal computers, which have the power to solve problems solvable in the past only on mainframe computers, has influenced the tabulated format of this book. Computer programs for structural analysis, employing techniques such as the finite element method, are also available for general use. These programs are very powerful; however, in many cases, elements of structural systems can be analyzed quite effectively independently without the need for an elaborate finite element model. In some instances, finite element models or programs are verified by comparing their solutions with the results given in a book such as this. Contained within this book are simple, accurate, and thorough tabulated formulations that can be applied to the stress analysis of a comprehensive range of structural components. This chapter serves to introduce the reader to the terminology, state property units and conversions, and contents of the book. 1.1
Terminology
Definitions of terms used throughout the book can be found in the glossary in Appendix B. 1.2
State Properties, Units, and Conversions
The basic state properties associated with stress analysis include the following: geometrical properties such as length, area, volume, centroid, center of gravity, and second-area moment (area moment of inertia); material properties such as mass density, modulus of elasticity, Poisson’s ratio, and thermal expansion coefficient; loading properties such as force, moment, and force distributions (e.g., force per unit length, force per unit area, and force per unit volume); other proper3
4
Formulas for Stress and Strain
TABLE 1.1
Units appropriate to structural analysis
Property Length Area Volume Second-area moment Mass Force Stress, pressure Work, energy Temperature y
[CHAP. 1
SI unit, symbol (derived units)
USCU unit,y symbol (derived units)
meter, m square meter (m2) cubic meter (m3) (m4) kilogram, kg Newton, N (kg-m=s2) Pascal, Pa (N=m2) Joule, J (N-m) Kelvin, K
inch, in square inch (in2) cubic inch (in3) (in4) (lbf-s2=in) pound, lbf psi (lbf=in2) (lbf-in) degrees Fahrenheit, F
In stress analysis, the unit of length used most often is the inch.
ties associated with loading, including energy, work, and power; and stress analysis properties such as deformation, strain, and stress. Two basic systems of units are employed in the field of stress analysis: SI units and USCU units.y SI units are mass-based units using the kilogram (kg), meter (m), second (s), and Kelvin (K) or degree Celsius ( C) as the fundamental units of mass, length, time, and temperature, respectively. Other SI units, such as that used for force, the Newton (kg-m=s2), are derived quantities. USCU units are force-based units using the pound force (lbf), inch (in) or foot (ft), second (s), and degree Fahrenheit ( F) as the fundamental units of force, length, time, and temperature, respectively. Other USCU units, such as that used for mass, the slug (lbf-s2=ft) or the nameless lbfs2=in, are derived quantities. Table 1.1 gives a listing of the primary SI and USCU units used for structural analysis. Certain prefixes may be appropriate, depending on the size of the quantity. Common prefixes are given in Table 1.2. For example, the modulus of elasticity of carbon steel is approximately 207 GPa ¼ 207 109 Pa ¼ 207 109 N=m2. Prefixes are normally used with SI units. However, there are cases where prefixes are also used with USCU units. Some examples are the kpsi (1 kpsi ¼ 103 psi ¼ 103 lbf =in2 ), kip (1 kip ¼ 1 kilopound ¼ 1000 lbf ), and Mpsi (1 Mpsi ¼ 106 psi). Depending on the application, different units may be specified. It is important that the analyst be aware of all the implications of the units and make consistent use of them. For example, if you are building a model from a CAD file in which the design dimensional units are given in mm, it is unnecessary to change the system of units or to scale the model to units of m. However, if in this example the input forces are in y SI and USCU are abbreviations for the International System of Units (from the French Syste´ me International d’Unite´ s) and the United States Customary Units, respectively.
SEC.
1.2]
TABLE 1.2
Introduction
5
Common prefixes
Prefix, symbol
Multiplication factor
Giga, G Mega, M Kilo, k Milli, m Micro, m Nano, n
109 106 103 103 106 109
Newtons, then the output stresses will be in N=mm2, which is correctly expressed as MPa. If in this example applied moments are to be specified, the units should be N-mm. For deflections in this example, the modulus of elasticity E should also be specified in MPa and the output deflections will be in mm. Table 1.3 presents the conversions from USCU units to SI units for some common state property units. For example, 10 kpsi ¼ ð6:895 103 Þ ð10 103 Þ ¼ 68:95 106 Pa ¼ 68:95 MPa. Obviously, the multiplication factors for conversions from SI to USCU are simply the reciprocals of the given multiplication factors.
TABLE 1.3
Multiplication factors to convert from USCU units to SI units To convert from USCU
Area: ft2 in2 Density: slug=ft3 (lbf-s2=ft4) lbf-s2=in4 Energy, work, or moment: ft-lbf or lbf-ft in-lbf or lbf-in Force: lbf Length: ft in Mass: slug (lbf-s2=ft) lbf-s2=in Pressure, stress: lbf=ft2 lbf=in2 (psi) Volume: ft3 in3
to SI
Multiply by
m2 m2
9:290 102 6:452 104
kg=m3 kg=m3
515.4 2:486 102
J or N-m J or N-m
1.356 0.1130
N
4.448
m m
0.3048 2:540 102
kg kg
14.59 1.216
Pa (N=m2) Pa (N=m2)
47.88 6:895 103
m3 m3
2:832 102 1:639 105
6
1.3
Formulas for Stress and Strain
[CHAP. 1
Contents
The remaining parts of this book are as follows. This part describes important relationships associated with stress and strain, basic material behavior, principles and analytical methods of the mechanics of structural elements, and numerical and experimental techniques in stress analysis.
Part 2: Facts; Principles; Methods.
This part contains the many applications associated with the stress analysis of structural components. Topics include the following: direct tension, compression, shear, and combined stresses; bending of straight and curved beams; torsion; bending of flat plates; columns and other compression members; shells of revolution, pressure vessels, and pipes; direct bearing and shear stress; elastic stability; stress concentrations; and dynamic and temperature stresses. Each chapter contains many tables associated with most conditions of geometry, loading, and boundary conditions for a given element type. The definition of each term used in a table is completely described in the introduction of the table.
Part 3: Formulas and Examples.
Appendices. The first appendix deals with the properties of a plane
area. The second appendix provides a glossary of the terminology employed in the field of stress analysis. The references given in a particular chapter are always referred to by number, and are listed at the end of each chapter.
Part
2 Facts; Principles; Methods
Chapter
2 Stress and Strain: Important Relationships
Understanding the physical properties of stress and strain is a prerequisite to utilizing the many methods and results of structural analysis in design. This chapter provides the definitions and important relationships of stress and strain.
2.1
Stress
Stress is simply a distributed force on an external or internal surface of a body. To obtain a physical feeling of this idea, consider being submerged in water at a particular depth. The ‘‘force’’ of the water one feels at this depth is a pressure, which is a compressive stress, and not a finite number of ‘‘concentrated’’ forces. Other types of force distributions (stress) can occur in a liquid or solid. Tensile (pulling rather than pushing) and shear (rubbing or sliding) force distributions can also exist. Consider a general solid body loaded as shown in Fig. 2.1(a). Pi and pi are applied concentrated forces and applied surface force distributions, respectively; and Ri and ri are possible support reaction force and surface force distributions, respectively. To determine the state of stress at point Q in the body, it is necessary to expose a surface containing the point Q. This is done by making a planar slice, or break, through the body intersecting the point Q. The orientation of this slice is arbitrary, but it is generally made in a convenient plane where the state of stress can be determined easily or where certain geometric relations can be utilized. The first slice, illustrated in Fig. 2.1(b), is arbitrarily oriented by the surface normal x. This establishes the yz plane. The external forces on the remaining body are shown, as well as the internal force (stress) distribution across the exposed internal 9
10
Formulas for Stress and Strain
[CHAP. 2
Figure 2.1
surface containing Q. In the general case, this distribution will not be uniform along the surface, and will be neither normal nor tangential to the surface at Q. However, the force distribution at Q will have components in the normal and tangential directions. These components will be tensile or compressive and shear stresses, respectively. Following a right-handed rectangular coordinate system, the y and z axes are defined perpendicular to x, and tangential to the surface. Examine an infinitesimal area DAx ¼ DyDz surrounding Q, as shown in Fig. 2.2(a). The equivalent concentrated force due to the force distribution across this area is DFx , which in general is neither normal nor tangential to the surface (the subscript x is used to designate the normal to the area). The force DFx has components in the x, y, and z directions, which are labeled DFxx , DFxy , and DFxz , respectively, as shown in Fig. 2.2(b). Note that the first subscript
SEC.
2.1]
Stress and Strain: Important Relationships
11
Figure 2.2
denotes the direction normal to the surface and the second gives the actual direction of the force component. The average distributed force per unit area (average stress) in the x direction isy s xx ¼
DFxx DAx
Recalling that stress is actually a point function, we obtain the exact stress in the x direction at point Q by allowing DAx to approach zero. Thus, sxx ¼ lim
DAx !0
DFxx DAx
or, sxx ¼
dFxx dAx
ð2:1-1Þ
Stresses arise from the tangential forces DFxy and DFxz as well, and since these forces are tangential, the stresses are shear stresses. Similar to Eq. (2.1-1), txy ¼
dFxy dAx
ð2:1-2Þ
txz ¼
dFxz dAx
ð2:1-3Þ
y Standard engineering practice is to use the Greek symbols s and t for normal (tensile or compressive) and shear stresses, respectively.
12
Formulas for Stress and Strain
Figure 2.3
[CHAP. 2
Stress components.
Since, by definition, s represents a normal stress acting in the same direction as the corresponding surface normal, double subscripts are redundant, and standard practice is to drop one of the subscripts and write sxx as sx . The three stresses existing on the exposed surface at the point are illustrated together using a single arrow vector for each stress as shown in Fig. 2.3. However, it is important to realize that the stress arrow represents a force distribution (stress, force per unit area), and not a concentrated force. The shear stresses txy and txz are the components of the net shear stress acting on the surface, where the net shear stress is given byy ðtx Þnet ¼
qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi t2xy þ t2xz
ð2:1-4Þ
To describe the complete state of stress at point Q completely, it would be necessary to examine other surfaces by making different planar slices. Since different planar slices would necessitate different coordinates and different free-body diagrams, the stresses on each planar surface would be, in general, quite different. As a matter of fact, in general, an infinite variety of conditions of normal and shear stress exist at a given point within a stressed body. So, it would take an infinitesimal spherical surface surrounding the point Q to understand and describe the complete state of stress at the point. Fortunately, through the use of the method of coordinate transformation, it is only necessary to know the state of stress on three different surfaces to describe the state of stress on any surface. This method is described in Sec. 2.3. The three surfaces are generally selected to be mutually perpendicular, and are illustrated in Fig. 2.4 using the stress subscript notation y
Stresses can only be added as vectors if they exist on a common surface.
SEC.
2.2]
Figure 2.4
Stress and Strain: Important Relationships
13
Stresses on three orthogonal surfaces.
as earlier defined. This state of stress can be written in matrix form, where the stress matrix ½s is given by 2 3 sx txy txz ½s ¼ 4 tyx sy tyz 5 ð2:1-5Þ tzx tzy sz Except for extremely rare cases, it can be shown that adjacent shear stresses are equal. That is, tyx ¼ txy , tzy ¼ tyz , and txz ¼ tzx , and the stress matrix is symmetric and written as 2 3 sx txy tzx ½s ¼ 4 txy sy tyz 5 ð2:1-6Þ tzx tyz sz
There are many practical problems where the stresses in one direction are zero. This situation is referred to as a case of plane stress. Arbitrarily selecting the z direction to be stress-free with sz ¼ tyz ¼ tyz ¼ 0, the last row and column of the stress matrix can be eliminated, and the stress matrix is written as sx txy ½s ¼ ð2:1-7Þ txy sy
Plane Stress.
and the corresponding stress element, viewed three-dimensionally and down the z axis, is shown in Fig. 2.5. 2.2
Strain and the Stress–Strain Relations
As with stresses, two types of strains exist: normal and shear strains, which are denoted by e and g, respectively. Normal strain is the rate of change of the length of the stressed element in a particular direction.
14
Formulas for Stress and Strain
Figure 2.5
[CHAP. 2
Plane stress.
Shear strain is a measure of the distortion of the stressed element, and has two definitions: the engineering shear strain and the elasticity shear strain. Here, we will use the former, more popular, definition. However, a discussion of the relation of the two definitions will be provided in Sec. 2.4. The engineering shear strain is defined as the change in the corner angle of the stress cube, in radians.
Initially, consider only one normal stress sx applied to the element as shown in Fig. 2.6. We see that the element increases in length in the x direction and decreases in length in the y and z directions. The dimensionless rate of increase in length is defined as the normal strain, where ex , ey , and ez represent the normal strains in
Normal Strain.
Figure 2.6
Deformation attributed to sx .
SEC.
2.2]
Stress and Strain: Important Relationships
15
the x, y, and z directions respectively. Thus, the new length in any direction is equal to its original length plus the rate of increase (normal strain) times its original length. That is, Dx0 ¼ Dx þ ex Dx;
Dy0 ¼ Dy þ ey Dy;
Dz0 ¼ Dz þ ez Dz
ð2:2-1Þ
There is a direct relationship between strain and stress. Hooke’s law for a linear, homogeneous, isotropic material is simply that the normal strain is directly proportional to the normal stress, and is given by 1 ½s nðsy þ sz Þ E x 1 ey ¼ ½sy nðsz þ sx Þ E 1 ez ¼ ½sz nðsx þ sy Þ E ex ¼
ð2:2-2aÞ ð2:2-2bÞ ð2:2-2cÞ
where the material constants, E and n, are the modulus of elasticity (also referred to as Young’s modulus) and Poisson’s ratio, respectively. Typical values of E and n for some materials are given in Table 2.1 at the end of this chapter. If the strains in Eqs. (2.2-2) are known, the stresses can be solved for simultaneously to obtain
sx ¼
E ½ð1 nÞex þ nðey þ ez Þ ð1 þ nÞð1 2nÞ
ð2:2-3aÞ
sy ¼
E ½ð1 nÞey þ nðez þ ex Þ ð1 þ nÞð1 2nÞ
ð2:2-3bÞ
sz ¼
E ½ð1 nÞez þ nðex þ ey Þ ð1 þ nÞð1 2nÞ
ð2:2-3cÞ
For plane stress, with sz ¼ 0, Eqs. (2.2-2) and (2.2-3) become 1 ðs nsy Þ E x 1 ey ¼ ðsy nsx Þ E n ez ¼ ðsx þ sy Þ E ex ¼
ð2:2-4aÞ ð2:2-4bÞ ð2:2-4cÞ
16
Formulas for Stress and Strain
[CHAP. 2
and sx ¼
E ðe þ ney Þ 1 n2 x
ð2:2-5aÞ
sy ¼
E ðe þ nex Þ 1 n2 y
ð2:2-5bÞ
The change in shape of the element caused by the shear stresses can be first illustrated by examining the effect of txy alone as shown in Fig. 2.7. The engineering shear strain gxy is a measure of the skewing of the stressed element from a rectangular parallelepiped. In Fig. 2.7(b), the shear strain is defined as the change in the angle BAD. That is, Shear Strain.
gxy ¼ ff BAD ff B0 A0 D 0 where gxy is in dimensionless radians. For a linear, homogeneous, isotropic material, the shear strains in the xy, yz, and zx planes are directly related to the shear stresses by txy G tyz gyz ¼ G tzx gzx ¼ G
gxy ¼
where the material constant, G, is called the shear modulus.
Figure 2.7
Shear deformation.
ð2:2-6aÞ ð2:2-6bÞ ð2:2-6cÞ
SEC.
2.3]
Stress and Strain: Important Relationships
17
It can be shown that for a linear, homogeneous, isotropic material the shear modulus is related to Poisson’s ratio by (Ref. 1) G¼
2.3
E 2ð1 þ nÞ
ð2:2-7Þ
Stress Transformations
As was stated in Sec. 2.1, knowing the state of stress on three mutually orthogonal surfaces at a point in a structure is sufficient to generate the state of stress for any surface at the point. This is accomplished through the use of coordinate transformations. The development of the transformation equations is quite lengthy and is not provided here (see Ref. 1). Consider the element shown in Fig. 2.8(a), where the stresses on surfaces with normals in the x, y, and z directions are known and are represented by the stress matrix 2 3 sx txy tzx ½sxyz ¼ 4 txy sy tyz 5 ð2:3-1Þ tzx tyz sz Now consider the element, shown in Fig. 2.8(b), to correspond to the state of stress at the same point but defined relative to a different set of surfaces with normals in the x0 , y0 , and z0 directions. The stress matrix corresponding to this element is given by 2 3 sx0 tx0 y0 tz0 x0 ð2:3-2Þ ½sx0 y0 z0 ¼ 4 tx0 y0 sy0 ty0 z0 5 tz0 x0 ty0 z0 sz0 To determine ½sx0 y0 z0 by coordinate transformation, we need to establish the relationship between the x0 y0 z0 and the xyz coordinate systems. This is normally done using directional cosines. First, let us consider the relationship between the x0 axis and the xyz coordinate system. The orientation of the x0 axis can be established by the angles yx0 x , yx0 y , and yx0 z , as shown in Fig. 2.9. The directional cosines for x0 are given by lx0 ¼ cos yx0 x ;
mx0 ¼ cos yx0 y ;
nx0 ¼ cos yx0 z
ð2:3-3Þ
Similarly, the y0 and z0 axes can be defined by the angles yy0 x , yy0 y , yy0 z and yz0 x , yz0 y , yz0 z , respectively, with corresponding directional cosines ly0 ¼ cos yy0 x ;
my0 ¼ cos yy0 y ;
ny0 ¼ cos yy0 z
ð2:3-4Þ
lz0 ¼ cos yz0 x ;
mz0 ¼ cos yz0 y ;
nz0 ¼ cos yz0 z
ð2:3-5Þ
18
Formulas for Stress and Strain
Figure 2.8
[CHAP. 2
The stress at a point using different coordinate systems.
It can be shown that the transformation matrix 2
lx0 ½T ¼ 4 ly0 lz0
mx0 my0 mz0
3 nx 0 ny 0 5 nz0
ð2:3-6Þ
SEC.
2.3]
Figure 2.9
Stress and Strain: Important Relationships
19
Coordinate transformation.
transforms a vector given in xyz coordinates, fVgxyz , to a vector in x0 y0 z0 coordinates, fVgx0 y0 z0 , by the matrix multiplication fVgx0 y0 z0 ¼ ½TfVgxyz
ð2:3-7Þ
Furthermore, it can be shown that the transformation equation for the stress matrix is given by (see Ref. 1) ½sx0 y0 z0 ¼ ½T½sxyz ½TT
ð2:3-8Þ
where ½TT is the transpose of the transformation matrix ½T, which is simply an interchange of rows and columns. That is, 2
lx0 ½TT ¼ 4 mx0 nx 0
ly0 my0 ny0
3 lz0 mz 0 5 nz 0
ð2:3-9Þ
The stress transformation by Eq. (2.3-8) can be implemented very easily using a computer spreadsheet or mathematical software. Defining the directional cosines is another matter. One method is to define the x0 y0 z0 coordinate system by a series of two-dimensional rotations from the initial xyz coordinate system. Table 2.2 at the end of this chapter gives transformation matrices for this.
20
Formulas for Stress and Strain
[CHAP. 2
EXAMPLE The state of stress at a point relative to an xyz coordinate system is given by the stress matrix 2
½sxyz
8 ¼4 6
2
3 6 2 4 25 2 5
MPa
Determine the state of stress on an element that is oriented by first rotating the xyz axes 45 about the z axis, and then rotating the resulting axes 30 about the new x axis. Solution. The surface normals can be found by a series of coordinate transformations for each rotation. From Fig. 2.10(a), the vector components for the first rotation can be represented by 8 9 2 38 9 cos y sin y 0 < x = < x1 = y ¼ 4 sin y cos y 0 5 y : 1; : ; z1 0 0 1 z
ðaÞ
The last rotation establishes the x0 y0 z0 coordinates as shown in Fig. 2.10(b), and they are related to the x1 y1 z1 coordinates by 8 09 2 38 9 1 0 0 <x = < x1 = y0 ¼ 4 0 cos j sin j 5 y1 : 0; : ; z z1 0 sin j cos j
ðbÞ
Substituting Eq. (a) in (b) gives 8 09 2 38 9 32 cos y sin y 0 > 1 0 0 > <x> <x > = = 7 6 76 y0 ¼ 4 0 cos j sin j 54 sin y cos y 0 5 y > > : > : 0> ; ; z z 0 0 1 0 sin j cos j 2 38 9 cos y sin y 0 > <x> = 6 7 ¼ 4 sin y cos j cos y cos j sin j 5 y > : > ; z sin y sin j cos y sin j cos j
Figure 2.10
ðcÞ
SEC.
2.3]
Stress and Strain: Important Relationships
21
Equation (c) is of the form of Eq. (2.3-7). Thus, the transformation matrix is 2
cos y ½T ¼ 4 sin y cos j sin y sin j
3 sin y 0 cos y cos j sin j 5
cos y sin j cos j
ðdÞ
Substituting y ¼ 45 and j ¼ 30 gives pffiffiffi 2 pffiffiffi 3 2 2 2 2 0 1 6 pffiffiffi pffiffiffi 7 ½T ¼ 4 6 6 2 5 4 pffiffiffi pffiffiffi pffiffiffi 2 2 2 3
ðeÞ
pffiffiffi pffiffiffi 3 2 pffiffiffi 2 2 6 2 p ffiffiffi p ffiffiffi pffiffiffi 7 16 ½TT ¼ 4 2 2 6 25 4 pffiffiffi 0 2 2 3
ð fÞ
The transpose of ½T is
From Eq. (2.3-8),
½sx0 y0 z0
pffiffiffi 2 pffiffiffi 32
8 6 2 2 2 2 0 1 6 pffiffiffi pffiffiffi 76 ¼ 4 6 6 2 54 6 4 4 pffiffiffi pffiffiffi pffiffiffi
2 2 2 2 2 3
pffiffiffi pffiffiffi 3 3 2 pffiffiffi 2 2 6 2 p ffiffiffi pffiffiffi 7 p ffiffiffi 1 7 6 25 42 2 6 25 4 pffiffiffi
5 0 2 2 3
2
This matrix multiplication can be performed simply using either a computer spreadsheet or mathematical software, resulting in 2
½sx0 y0 z0
4 ¼ 4 5:196
3
5:196
4:801 2:714
3
3 2:714 5
8:199
MPa
Stresses on a Single Surface. If one was concerned about the state of stress on one particular surface, a complete stress transformation would be unnecessary. Let the directional cosines for the normal of the surface be given by l, m, and n. It can be shown that the normal stress on the surface is given by
s ¼ sx l2 þ sy m2 þ sz n2 þ 2txy lm þ 2tyz mn þ 2tzx nl
ð2:3-10Þ
and the net shear stress on the surface is t ¼ ½ðsx l þ txy m þ tzx nÞ2 þ ðtxy l þ sy m þ tyz nÞ2 þ ðtzx l þ tyz m þ sz nÞ2 s2 1=2
ð2:3-11Þ
22
Formulas for Stress and Strain
[CHAP. 2
The direction of t is established by the directional cosines 1 lt ¼ ½ðsx sÞl þ txy m þ tzx n t 1 mt ¼ ½txy l þ ðsy sÞm þ tyz n t
ð2:3-12Þ
1 nt ¼ ½tzx l þ tyz m þ ðsz sÞn t
EXAMPLE The state of stress at a particular point relative to the xyz coordinate system is 2
½sxyz
3 14 7 7 ¼ 4 7 10 05
7 0 35
kpsi
Determine the normal and shear stress on a surface at the point where the surface is parallel to the plane given by the equation 2x y þ 3z ¼ 9 Solution. The normal to the surface is established by the directional numbers of the plane and are simply the coefficients of x, y, and z terms of the equation of the plane. Thus, the directional numbers are 2, 1, and 3. The directional cosines of the normal to the surface are simply the normalized values of the directional numbers, which are the directional numbers divided qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi pffiffiffiffiffiffi by 22 þ ð 1Þ2 þ 32 ¼ 14. Thus pffiffiffiffiffiffi l ¼ 2= 14;
pffiffiffiffiffiffi m ¼ 1= 14;
pffiffiffiffiffiffi n ¼ 3= 14
From the stress matrix, sx ¼ 14, txy ¼ 7, tzx ¼ 7, sy ¼ 10, tyz ¼ 0, and sz ¼ 35 kpsi. Substituting the stresses and directional cosines into Eq. (2.3-10) gives pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi s ¼ 14ð2= 14Þ2 þ 10ð 1= 14Þ2 þ 35ð3= 14Þ2 þ 2ð7Þð2= 14Þð 1= 14Þ pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi þ 2ð0Þð 1= 14Þð3= 14Þ þ 2ð 7Þð3= 14Þð2= 14Þ ¼ 19:21 kpsi The shear stress is determined from Eq. (2.3-11), and is pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi t ¼ f½14ð2= 14Þ þ 7ð 1= 14Þ þ ð 7Þð3= 14Þ2 pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi þ ½7ð2= 14Þ þ 10ð 1= 14Þ þ ð0Þð3= 14Þ2 pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi þ ½ð 7Þð2= 14Þ þ ð0Þð 1= 14Þ þ 35ð3= 14Þ2 ð19:21Þ2 g1=2 ¼ 14:95 kpsi
SEC.
2.3]
Stress and Strain: Important Relationships
23
From Eq. (2.3-12), the directional cosines for the direction of t are lt ¼
pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi 1 ½ð14 19:21Þð2= 14Þ þ 7ð 1= 14Þ þ ð 7Þð3= 14Þ ¼ 0:687 14:95
mt ¼
pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi 1 ½7ð2= 14Þ þ ð10 19:21Þð 1= 14Þ þ ð0Þð3= 14Þ ¼ 0:415 14:95
nt ¼
pffiffiffiffiffiffi pffiffiffiffiffiffi pffiffiffiffiffiffi 1 ½ð 7Þð2= 14Þ þ ð0Þð 1= 14Þ þ ð35 19:21Þð3= 14Þ ¼ 0:596 14:95
Plane Stress. For the state of plane stress shown in Fig. 2.11(a), sz ¼ tyz ¼ tzx ¼ 0. Plane stress transformations are normally performed in the xy plane, as shown in Fig. 2.11(b). The angles relating the x0 y0 z0 axes to the xyz axes are
yx0 x ¼ y;
yx0 y ¼ 90 y;
yx0 z ¼ 90
yy0 x ¼ y þ 90 ;
yy0 y ¼ y;
yy0 z ¼ 90
yz0 x ¼ 90 ;
yz0 y ¼ 90 ;
yz0 z ¼ 0
Thus the directional cosines are lx0 ¼ cos y ly0 ¼ sin y lz0 ¼ 0
mx0 ¼ sin y my0 ¼ cos y mz0 ¼ 0
nx 0 ¼ 0 ny 0 ¼ 0 nz 0 ¼ 1
The last rows and columns of the stress matrices are zero so the stress matrices can be written as ½sxy ¼
Figure 2.11
Plane stress transformations.
sx txy
txy sy
ð2:3-13Þ
24
Formulas for Stress and Strain
[CHAP. 2
and
½sx0 y0
sx 0 ¼ tx0 y0
tx0 y0 sy0
ð2:3-14Þ
Since the plane stress matrices are 2 2, the transformation matrix and its transpose are written as
cos y ½T ¼
sin y
sin y ; cos y
cos y sin y ½T ¼ sin y cos y T
ð2:3-15Þ
Equations (2.3-13)–(2.3-15) can then be substituted into Eq. (2.3-8) to perform the desired transformation. The results, written in long-hand form, would be sx0 ¼ sx cos2 y þ sy sin2 y þ 2txy cos y sin y sy0 ¼ sx sin2 y þ sy cos2 y 2txy cos y sin y 2
ð2:3-16Þ 2
tx0 y0 ¼ ðsx sy Þ sin y cos y þ txy ðcos y sin yÞ If the state of stress is desired on a single surface with a normal rotated y counterclockwise from the x axis, the first and third equations of Eqs. (2.3-16) can be used as given. However, using trigonometric identities, the equations can be written in slightly different form. Letting s and t represent the desired normal and shear stresses on the surface, the equations are s¼
sx þ sy sx sy þ cos 2y þ txy sin 2y 2 2
sx sy t¼
sin 2y þ txy cos 2y 2
ð2:3-17Þ
Equations (2.3-17) represent a set of parametric equations of a circle in the st plane. This circle is commonly referred to as Mohr’s circle and is generally discussed in standard mechanics of materials textbooks. This serves primarily as a teaching tool and adds little to applications, so it will not be represented here (see Ref. 1). In general, maximum and minimum values of the normal stresses occur on surfaces where the shear stresses are zero. These stresses, which are actually the eigenvalues of the stress matrix, are called the principal stresses. Three principal stresses exist, s1 , s2 , and s3 , where they are commonly ordered as s1 5 s2 5 s3 .
Principal Stresses.
SEC.
2.3]
Stress and Strain: Important Relationships
25
Considering the stress state given by the matrix of Eq. (2.3-1) to be known, the principal stresses sp are related to the given stresses by ðsx sp Þlp þ txy mp þ tzx np ¼ 0 txy lp þ ðsy sp Þmp þ tyz np ¼ 0
ð2:3-18Þ
tzx lp þ tyz mp þ ðsz sp Þnp ¼ 0 where lp , mp , and np are the directional cosines of the normals to the surfaces containing the principal stresses. One possible solution to Eqs. (2.3-18) is lp ¼ mp ¼ np ¼ 0. However, this cannot occur, since l2p þ m2p þ n2p ¼ 1
ð2:3-19Þ
To avoid the zero solution of the directional cosines of Eqs. (2.3-18), the determinant of the coefficients of lp , mp , and np in the equation is set to zero. This makes the solution of the directional cosines indeterminate from Eqs. (2.3-18). Thus, ðsx sp Þ txy tzx ¼0 txy ðs
s Þ t y p yz tzx tyz ðsz sp Þ Expanding the determinant yields s3p ðsx þ sy þ sz Þs2p þ ðsx sy þ sy sz þ sz sx t2xy t2yz t2zx Þsp
ðsx sy sz þ 2txy tyz tzx sx t2yz sy t2zx sz t2xy Þ ¼ 0
ð2:3-20Þ
where Eq. (2.3-20) is a cubic equation yielding the three principal stresses s1 , s2 , and s3 . To determine the directional cosines for a specific principal stress, the stress is substituted into Eqs. (2.3-18). The three resulting equations in the unknowns lp , mp , and np will not be independent since they were used to obtain the principal stress. Thus, only two of Eqs. (2.3-18) can be used. However, the second-order Eq. (2.3-19) can be used as the third equation for the three directional cosines. Instead of solving one second-order and two linear equations simultaneously, a simplified method is demonstrated in the following example.y
y Mathematical software packages can be used quite easily to extract the eigenvalues (sp ) and the corresponding eigenvectors (lp , mp , and np ) of a stress matrix. The reader is urged to explore software such as Mathcad, Matlab, Maple, and Mathematica, etc.
26
Formulas for Stress and Strain
[CHAP. 2
EXAMPLE For the following stress matrix, determine the principal stresses and the directional cosines associated with the normals to the surfaces of each principal stress. 2
3 ½s ¼ 4 1 1
3 1 1 0 25 2 0
MPa
Solution. Substituting sx ¼ 3, txy ¼ 1, tzx ¼ 1, sy ¼ 0, tyz ¼ 2, and sz ¼ 0 into Eq. (2.3-20) gives s2p ð3 þ 0 þ 0Þs2p þ ½ð3Þð0Þ þ ð0Þð0Þ þ ð0Þð3Þ 22 12 12 sp
½ð3Þð0Þð0Þ þ ð2Þð2Þð1Þð1Þ ð3Þð22 Þ ð0Þð12 Þ ð0Þð12 Þ ¼ 0 which simplifies to s2p 3s2p 6sp þ 8 ¼ 0
ðaÞ
The solutions to the cubic equation are sp ¼ 4, 1, and 2 MPa. Following the conventional ordering, s1 ¼ 4 MPa;
s2 ¼ 1 MPa;
s3 ¼ 2 MPa
The directional cosines associated with each principal stress are determined independently. First, consider s1 and substitute sp ¼ 4 MPa into Eqs. (2.3-18). This results in
l1 þ m1 þ n1 ¼ 0 l1 4m1 þ 2n1 ¼ 0 l1 þ 2m1 4n1 ¼ 0
ðbÞ ðcÞ ðdÞ
where the subscript agrees with that of s1 . Equations (b), (c), and (d) are no longer independent since they were used to determine the values of sp . Only two independent equations can be used, and in this example, any two of the above can be used. Consider Eqs. (b) and (c), which are independent. A third equation comes from Eq. (2.3-19), which is nonlinear in l1 , m1 , and n1 . Rather than solving the three equations simultaneously, consider the following approach. Arbitrarily, let l1 ¼ 1 in Eqs. (b) and (c). Rearranging gives m1 þ n1 ¼ 1 4m1 2n1 ¼ 1
SEC.
2.3]
Stress and Strain: Important Relationships
27
solving these simultaneously gives m1 ¼ n1 ¼ 12. These values of l1 , m1 , and n1 do not satisfy Eq. (2.3-19). However, all that remains is to normalize their qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi pffiffiffi values by dividing by 12 þ ð12Þ2 þ ð12Þ2 ¼ 6=2: Thus,y pffiffiffi pffiffiffi l1 ¼ ð1Þð2= 6Þ ¼ 6=3 pffiffiffi pffiffiffi m1 ¼ ð1=2Þð2= 6Þ ¼ 6=6 pffiffiffi pffiffiffi n1 ¼ ð1=2Þð2= 6Þ ¼ 6=6 Repeating the same procedure for s2 ¼ 1 MPa results in l2 ¼
pffiffiffi 3=3;
pffiffiffi m2 ¼ 3=3;
pffiffiffi n2 ¼ 3=3
and for s3 ¼ 2 MPa l3 ¼ 0;
m3 ¼
pffiffiffi 2=2;
pffiffiffi n3 ¼ 2=2
If two of the principal stresses are equal, there will exist an infinite set of surfaces containing these principal stresses, where the normals of these surfaces are perpendicular to the direction of the third principal stress. If all three principal stresses are equal, a hydrostatic state of stress exists, and regardless of orientation, all surfaces contain the same principal stress with no shear stress. Considering the stress element shown in Fig. 2.11(a), the shear stresses on the surface with a normal in the z direction are zero. Thus, the normal stress sz ¼ 0 is a principal stress. The directions of the remaining two principal stresses will be in the xy plane. If tx0 y0 ¼ 0 in Fig. 2.11(b), then sx0 would be a principal stress, sp with lp ¼ cos y, mp ¼ sin y, and np ¼ 0. For this case, only the first two of Eqs. (2.3-18) apply, and are Principal Stresses, Plane Stress.
ðsx sp Þ cos y þ txy sin y ¼ 0 txy cos y þ ðsy sp Þ sin y ¼ 0
ð2:3-21Þ
As before, we eliminate the trivial solution of Eqs. (2.3-21) by setting the determinant of the coefficients of the directional cosines to zero. That is, ðs s Þ txy p x ¼ ðsx sp Þðsy sp Þ t2xy txy ðsy sp Þ ¼ s2p ðsx þ sy Þsp þ ðsx sy t2xy Þ ¼ 0
ð2:3-22Þ
y This method has one potential flaw. If l1 is actually zero, then a solution would not result. If this happens, simply repeat the approach letting either m1 or n1 equal unity.
28
Formulas for Stress and Strain
[CHAP. 2
Equation (2.3-22) is a quadratic equation in sp for which the two solutions are qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 ðsx þ sy Þ ðsx sy Þ2 þ 4t2xy sp ¼ ð2:3-23Þ 2 Since for plane stress, one of the principal stresses (sz ) is always zero, numbering of the stresses (s1 5 s2 5 s3 ) cannot be performed until Eq. (2.3-23) is solved. Each solution of Eq. (2.3-23) can then be substituted into one of Eqs. (2.3-21) to determine the direction of the principal stress. Note that if sx ¼ sy and txy ¼ 0, then sx and sy are principal stresses and Eqs. (2.3-21) are satisfied for all values of y. This means that all stresses in the plane of analysis are equal and the state of stress at the point is isotropic in the plane. EXAMPLE Determine the principal stresses for a case of plane stress given by the stress matrix 5 4 ½s ¼ kpsi
4 11 Show the element containing the principal stresses properly oriented with respect to the initial xyz coordinate system. Solution. From the stress matrix, sx ¼ 5, sy ¼ 11, and txy ¼ 4 kpsi and Eq. (2.3-23) gives qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi sp ¼ 12 ð5 þ 11Þ ð5 11Þ2 þ 4ð 4Þ2 ¼ 13; 3 kpsi Thus, the three principal stresses (s1 ; s2 ; s3 ), are (13, 3, 0) kpsi, respectively. For directions, first substitute s1 ¼ 13 kpsi into either one of Eqs. (2.3-21). Using the first equation with y ¼ y1 ðsx s1 Þ cos y1 þ txy sin y1 ¼ ð5 13Þ cos y1 þ ð 4Þ sin y1 ¼ 0 or 8 ¼ 63:4 y1 ¼ tan 1
4 Now for the other principal stress, s2 ¼ 3 kpsi, the first of Eqs. (2.3-21) gives ðsx s2 Þ cos y2 þ txy sin y2 ¼ ð5 3Þ cos y2 þ ð 4Þ sin y2 ¼ 0 or y2 ¼ tan 1
2 ¼ 26:6 4
SEC.
2.3]
Figure 2.12
Stress and Strain: Important Relationships
29
Plane stress example.
Figure 2.12(a) illustrates the initial state of stress, whereas the orientation of the element containing the in-plane principal stresses is shown in Fig. 2.12(b).
Consider that the principal stresses for a general stress state have been determined using the methods just described and are illustrated by Fig. 2.13. The 123 axes represent the normals for the principal surfaces with directional cosines determined by Eqs. (2.3-18) and (2.3-19). Viewing down a principal stress axis (e.g., the 3 axis) and performing a plane stress transformation in the plane normal to that axis (e.g., the 12 plane), one would find that the shear stress is a maximum on surfaces 45 from the two principal stresses in that plane (e.g., s1 , s2 ). On these surfaces, the maximum shear stress would be one-half the difference of the principal stresses [e.g., tmax ¼ ðs1 s2 Þ=2] and will also have a normal stress equal to the average of the principal stresses [e.g., save ¼ ðs1 þ s2 Þ=2]. Viewing along the three principal axes would result in three shear stress
Maximum Shear Stresses.
Figure 2.13
Principal stress state.
30
Formulas for Stress and Strain
[CHAP. 2
maxima, sometimes referred to as the principal shear stresses. These stresses together with their accompanying normal stresses are Plane 1; 2: Plane 2; 3:
ðtmax Þ1;2 ¼ ðs1 s2 Þ=2; ðtmax Þ2;3 ¼ ðs2 s3 Þ=2;
ðsave Þ1;2 ¼ ðs1 þ s2 Þ=2 ðsave Þ2;3 ¼ ðs2 þ s3 Þ=2
Plane 1; 3:
ðtmax Þ1;3 ¼ ðs1 s3 Þ=2;
ðsave Þ1;3 ¼ ðs1 þ s3 Þ=2 ð2:3-24Þ
Since conventional practice is to order the principal stresses by s1 5 s2 5 s3 , the largest shear stress of all is given by the third of Eqs. (2.3-24) and will be repeated here for emphasis: tmax ¼ ðs1 s3 Þ=2
ð2:3-25Þ
EXAMPLE In the previous example, the principal stresses for the stress matrix
5 ½s ¼
4
4 11
kpsi
were found to be (s1 ; s2 ; s3 Þ ¼ ð13; 3; 0Þ kpsi. The orientation of the element containing the principal stresses was shown in Fig. 2.12(b), where axis 3 was the z axis and normal to the page. Determine the maximum shear stress and show the orientation and complete state of stress of the element containing this stress. Solution. The initial element and the transformed element containing the principal stresses are repeated in Fig. 2.14(a) and (b), respectively. The maximum shear stress will exist in the 1, 3 plane and is determined by substituting s1 ¼ 13 and s3 ¼ 0 into Eqs. (2.3-24). This results in ðtmax Þ1;3 ¼ ð13 0Þ=2 ¼ 6:5 kpsi;
ðsave Þ1;3 ¼ ð13 þ 0Þ=2 ¼ 6:5 kpsi
To establish the orientation of these stresses, view the element along the axis containing s2 ¼ 3 kpsi [view A, Fig. 2.14(c)] and rotate the surfaces 45 as shown in Fig. 2.14(c). The directional cosines associated with the surfaces are found through successive rotations. Rotating the xyz axes to the 123 axes yields 8 9 2 cos 63:4 > <1> = 6 2 ¼ 4 sin 63:4 > : > ; 3 0 2
0:4472 6 ¼ 4 0:8944 0
sin 63:4 cos 63:4 0
8 9 0> <x> = 0 y > : > ; 1 z
38 9
0:8944 0 > <x> = 7 0:4472 0 5 y > : > ; 0 1 z
ðaÞ
SEC.
2.3]
Stress and Strain: Important Relationships
Figure 2.14
31
Plane stress maximum shear stress.
A counterclockwise rotation of 45 of the normal in the 3 direction about axis 2 is represented by 8 09 2 38 9 cos 45 0 sin 45 > > <x > <1> = = 6 7 y0 ¼ 4 0 1 0 5 2 > > : 0> : > ; ; z cos 45 sin 45 0 3 38 9 0 0:7071 > <1> = 7 1 0 5 2 > > : ; 0 0:7071 3
2
0:7071 6 ¼4 0 0:7071 Thus, 8 09 2 0:7071 0 > <x > = 6 y0 ¼ 4 0 1 > : 0> ; z 0:7071 0 2
0:7071
32
0:4472
76 0 54 0:8944 0:7071 0
0:3162 0:6325 6 ¼ 4 0:8944 0:4472 0:3162 0:6325
38 9
0:8944 0 < >x> = 7 0:4472 0 5 y > : > ; 0 1 z
38 9
0:7071 > <x> = 7 0 5 y > : > ; 0:7071 z
ðbÞ
32
Formulas for Stress and Strain
[CHAP. 2
The directional cosines for Eq. (2.1-14c) are therefore 2 3 2 3 nx0 x nx0 y nx0 z 0:3162 0:6325 0:7071 4 ny0 x ny0 y ny0 z 5 ¼ 4 0:8944 0:4472 0 5 nz0 x nz0 y nz0 z 0:3162 0:6325 0:7071 The other surface containing the maximum shear stress can be found similarly except for a clockwise rotation of 45 for the second rotation.
2.4
Strain Transformations
The equations for strain transformations are identical to those for stress transformations. However, the engineering strains as defined in Sec. 2.2 will not transform. Transformations can be performed if the shear strain is modified. All of the equations for the stress transformations can be employed simply by replacing s and t in the equations by e and g=2 (using the same subscripts), respectively. Thus, for example, the equations for plane stress, Eqs. (2.3-16), can be written for strain as ex0 ¼ ex cos2 y þ ey sin2 y þ gxy cos y sin y ey0 ¼ ex sin2 y þ ey cos2 y gxy cos y sin y 2
ð2:4-1Þ 2
gx0 y0 ¼ 2ðex ey Þ sin y cos y þ gxy ðcos y sin yÞ 2.5
Reference
1. Budynas, R. G.: ‘‘Advanced Strength and Applied Stress Analysis,’’ 2nd ed., McGrawHill, 1999.
SEC.
2.6]
2.6
Stress and Strain: Important Relationships
33
Tables
TABLE 2.1
Material propertiesy Thermal expansion coefficient, a
Modulus of elasticity, E Material
Mpsi
GPa
Poisson’s ratio, n
m= F
m= C
Aluminum alloys
10.5
72
0.33
13.1
23.5
Brass (65=35)
16
110
0.32
11.6
20.9
4
34
0.20
5.5
9.9
Copper
17
118
0.33
9.4
16.9
Glass
10
69
0.24
5.1
9.2
Iron (gray cast)
13
90
0.26
6.7
12.1
Steel (structural)
29.5
207
0.29
6.5
11.7
Steel (stainless)
28
193
0.30
9.6
17.3
Titanium (6 A1=4 V)
16.5
115
0.34
5.2
9.5
Concrete
y
The values given in this table are to be treated as approximations of the true behavior of an actual batch of the given material. TABLE 2.2
Transformation matrices for positive rotations about an axisy
Axis
Transformation matrix
x axis: 8 9 2 1 0 < x1 = y1 ¼ 4 0 cos y : ; z1 0 sin y
38 9 0 <x= sin y 5 y : ; cos y z
y axis: 8 9 2 cos y < x1 = y1 ¼ 4 0 : ; sin y z1
38 9 0 sin y < x = 1 0 5 y : ; 0 cos y z
z axis: 8 9 2 cos y < x1 = y1 ¼ 4 sin y : ; 0 z1
y
38 9 sin y 0 < x = cos y 0 5 y : ; 0 1 z
A positive rotation about a given axis is counterclockwise about the axis (as viewed from the positive axis direction).
34
Formulas for Stress and Strain
TABLE 2.3
[CHAP. 2
Transformation equations
General state of stress ½sx0 y0 z0 ¼ ½T½sxyz ½TT where 2
½sx0 y0 z0
sx0 6 ¼ 4 tx0 y0
tx0 y0 sy0
3 tz0 x0 ty0 z0 7 5;
tz0 x0
ty0 z0
sz0
2
lx0
6 ½T ¼ 4 ly0 lz0
mx0
nx0
3
my0
7 ny0 5;
mz0
nz0
2
½sxyz
sx 6 ¼ 4 txy
txy sy
3 tzx tyz 7 5
tzx
tyz
sz
Stresses on a single surface (l, m, n are directional cosines of surface normal) s ¼ sx l2 þ sy m2 þ sz n2 þ 2txy lm þ 2tyz mn þ 2tzx nl t ¼ ½ðsx l þ txy m þ tzx nÞ2 þ ðtxy l þ sy m þ tyz nÞ2 þ ðtzx l þ tyz m þ sz nÞ2 s2 1=2 1 lt ¼ ½ðsx sÞl þ txy m þ tzx n t 1 mt ¼ ½txy l þ ðsy sÞm þ tyz n t 1 nt ¼ ½tzx l þ tyz m þ ðsz sÞn t lt , mt , and nt are directional cosines for the direction of t. Plane stress (y is counterclockwise from x axis to surface normal, x0 ) s ¼ 12 ðsx þ sy Þ þ 12 ðsx sy Þ cos 2y þ txy sin 2y t ¼ 12 ðsx sy Þ sin 2y þ txy cos 2y Principal stresses (general case) s3p ðsx þ sy þ sz Þs2p þ ðsx sy þ sy sz þ sz sx t2xy t2yz t2zx Þsp
ðsx sy sz þ 2txy tyz tzx sx t2yz sy t2zx sz t2xy Þ ¼ 0 Directional cosines (lp , mp , np ) are found from three of the following equations: 9 ðsx sp Þlp þ txy mp þ tzx np ¼ 0 = txy lp þ ðsy sp Þmp þ tyz np ¼ 0 select two independent equations ; tzx lp þ tyz mp þ ðsz sp Þnp ¼ 0 l2p þ m2p þ n2p ¼ 1 Principal stresses (plane stress) One principal stress is zero and the remaining two are given by qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi sp ¼ 12 ðsx þ sy Þ ðsx sy Þ2 þ 4t2xy Angle of surface normal relative to the x axis is given by !
1 sp sx yp ¼ tan txy
Chapter
3 The Behavior of Bodies under Stress
This discussion pertains to the behavior of what are commonly designated as structural materials. That is, materials suitable for structures and members that must sustain loads without suffering damage. Included in this category are most of the metals, concrete, wood, composite materials, some plastics, etc. It is beyond the scope of this book to give more than a mere statement of a few important facts concerning the behavior of a stressed material. Extensive literature is available on every phase of the subject, and the articles contained herein will serve as an introduction only.
3.1
Methods of Loading
The mechanical properties of a material are usually determined by laboratory tests, and the commonly accepted values of ultimate strength, elastic limit, etc., are those found by testing a specimen of a certain form in a certain manner. To apply results so obtained in engineering design requires an understanding of the effects of many different variables, such as form and scale, temperature and other conditions of service, and method of loading. The method of loading, in particular, affects the behavior of bodies under stress. There are an infinite number of ways in which stress may be applied to a body, but for most purposes it is sufficient to distinguish the types of loading now to be defined. 1. Short-time static loading. The load is applied so gradually that at any instant all parts are essentially in equilibrium. In testing, the load is increased progressively until failure occurs, and the total time required to produce failure is not more than a few minutes. In 35
36
Formulas for Stress and Strain
[CHAP. 3
service, the load is increased progressively up to its maximum value, is maintained at that maximum value for only a limited time, and is not reapplied often enough to make fatigue a consideration. The ultimate strength, elastic limit, yield point, yield strength, and modulus of elasticity of a material are usually determined by short-time static testing at room temperature. 2. Long-time static loading. The maximum load is applied gradually and maintained. In testing, it is maintained for a sufficient time to enable its probable final effect to be predicted; in service, it is maintained continuously or intermittently during the life of the structure. The creep, or flow characteristics, of a material and its probable permanent strength are determined by long-time static testing at the temperatures prevailing under service conditions. (See Sec. 3.6.) 3. Repeated loading. Typically, a load or stress is applied and wholly or partially removed or reversed repeatedly. This type of loading is important if high stresses are repeated for a few cycles or if relatively lower stresses are repeated many times; it is discussed under Fatigue. (See Sec. 3.8.) 4. Dynamic loading. The circumstances are such that the rate of change of momentum of the parts must be taken into account. One such condition may be that the parts are given definite accelerations corresponding to a controlled motion, such as the constant acceleration of a part of a rotating member or the repeated accelerations suffered by a portion of a connecting rod. As far as stress effects are concerned, these loadings are treated as virtually static and the inertia forces (Sec. 16.2) are treated exactly as though they were ordinary static loads. A second type of quasi-static loading, quick static loading, can be typified by the rapid burning of a powder charge in a gun barrel. Neither the powder, gas, nor any part of the barrel acquires appreciable radial momentum; therefore equilibrium may be considered to exist at any instant and the maximum stress produced in the gun barrel is the same as though the powder pressure had developed gradually. In static loading and the two types of dynamic loading just described, the loaded member is required to resist a definite force. It is important to distinguish this from impact loading, where the loaded member is usually required to absorb a definite amount of energy. Impact loading can be divided into two general categories. In the first case a relatively large slow-moving mass strikes a less massive beam or bar and the kinetic energy of the moving mass is assumed to be converted into strain energy in the beam. All portions of the beam
SEC.
3.2]
The Behavior of Bodies under Stress
37
and the moving mass are assumed to stop moving simultaneously. The shape of the elastic axis of the deflected beam or bar is thus the same as in static loading. A special case of this loading, generally called sudden loading, occurs when a mass that is not moving is released when in contact with a beam and falls through the distance the beam deflects. This produces approximately twice the stress and deflection that would have been produced had the mass been ‘‘eased’’ onto the beam (see Sec. 16.4). The second case of impact loading involves the mass of the member being struck. Stress waves travel through the member during the impact and continue even after the impacting mass has rebounded (see Sec. 16.3). On consideration, it is obvious that methods of loading really differ only in degree. As the time required for the load to be applied increases, short-time static loading changes imperceptibly into longtime static loading; impact may be produced by a body moving so slowly that the resulting stress conditions are practically the same as though equal deflection had been produced by static loading; the number of stress repetitions at which fatigue becomes involved is not altogether definite. Furthermore, all these methods of loading may be combined or superimposed in various ways. Nonetheless, the classification presented is convenient because most structural and machine parts function under loading that may be classified definitely as one of the types described. 3.2
Elasticity; Proportionality of Stress and Strain
In determining stress by mathematical analysis, it is customary to assume that material is elastic, isotropic, homogeneous, and infinitely divisible without change in properties and that it conforms to Hooke’s law, which states that strain is proportional to stress. Actually, none of these assumptions is strictly true. A structural material is usually an aggregate of crystals, fibers, or cemented particles, the arrangement of which may be either random or systematic. When the arrangement is random the material is essentially isotropic if the part considered is large in comparison with the constituent units; when the arrangement is systematic, the elastic properties and strength are usually different in different directions and the material is anisotropic. Again, when subdivision is carried to the point where the part under consideration comprises only a portion of a single crystal, fiber, or other unit, in all probability its properties will differ from those of a larger part that is an aggregate of such units. Finally, very careful experiments show that for all materials there is probably some set and some deviation from Hooke’s law for any stress, however small. These facts impose certain limitations upon the conventional methods of stress analysis and must often be taken into account, but
38
Formulas for Stress and Strain
[CHAP. 3
formulas for stress and strain, mathematically derived and based on the assumptions stated, give satisfactory results for nearly all problems of engineering design. In particular, Hooke’s law may be regarded as practically true up to a proportional limit, which, though often not sharply defined, can be established for most materials with sufficient definiteness. So, too, a fairly definite elastic limit is determinable; in most cases it is so nearly equal to the proportional limit that no distinction need be made between the two.
3.3
Factors Affecting Elastic Properties
For ordinary purposes it may be assumed that the elastic properties of most metals, when stressed below a nominal proportional limit, are constant with respect to stress, unaffected by ordinary atmospheric variations of temperature, unaffected by prior applications of moderate stress, and independent of the rate of loading. When precise relations between stress and strain are important, as in the design or calibration of instruments, these assumptions cannot always be made. The fourth edition of this book (Ref. 1) discussed in detail the effects of strain rate, temperature, etc., on the elastic properties of many metals and gave references for the experiments performed. The relationships between atomic and molecular structure and the elastic properties are discussed in texts on materials science. Wood exhibits a higher modulus of elasticity and much higher proportional limit when tested rapidly than when tested slowly. The standard impact test on a beam indicates a fiber stress at the proportional limit approximately twice as great as that found by the standard static bending test. Absorption of moisture up to the fiber saturation point greatly lowers both the modulus of elasticity and the proportional limit (Ref. 2). Both concrete and cast iron have stress-strain curves more or less curved throughout, and neither has a definite proportional limit. For these materials it is customary to define E as the ratio of some definite stress (for example, the allowable stress or one-fourth the ultimate strength) to the corresponding unit strain; the quantity so determined is called the secant modulus since it represents the slope of the secant of the stress-strain diagram drawn from the origin to the point representing the stress chosen. The moduli of elasticity of cast iron are much more variable than those of steel, and the stronger grades are stiffer than the weaker ones. Cast iron suffers a distinct set from the first application of even a moderate stress; but after several repetitions of that stress, the material exhibits perfect elasticity up to, but not beyond, that stress. The modulus of elasticity is slightly less in tension than in compression.
SEC.
3.5]
The Behavior of Bodies under Stress
39
Concrete also shows considerable variation in modulus of elasticity, and in general its stiffness increases with its strength. Like cast iron, concrete can be made to exhibit perfect elasticity up to a moderate stress by repeated loading up to that stress. Because of its tendency to yield under continuous loading, the modulus of elasticity indicated by long-time loading is much less than that obtained by progressive loading at ordinary speeds. 3.4
Load–Deformatlon Relation for a Body
If Hooke’s law holds for the material of which a member or structure is composed, the member or structure will usually conform to a similar law of load-deformation proportionality and the deflection of a beam or truss, the twisting of a shaft, the dilation of a pressure container, etc., may in most instances be assumed proportional to the magnitude of the applied load or loads. There are two important exceptions to this rule. One is to be found in any case where the stresses due to the loading are appreciably affected by the deformation. Examples of this are: a beam subjected to axial and transverse loads; a flexible wire or cable held at the ends and loaded transversely; a thin diaphragm held at the edges and loaded normal to its plane; a ball pressed against a plate or against another ball; and a helical spring under severe extension. The second exception is represented by any case in which failure occurs through elastic instability, as in the compressive loading of a long, slender column. Here, for compression loads less than a specific critical (Euler) load, elastic instability plays no part and the axial deformation is linear with load. At the critical load, the type of deformation changes, and the column bends instead of merely shortening axially. For any load beyond the critical load, high bending stresses and failure occurs through excessive deflection (see Sec. 3.13). 3.5
Plasticity
Elastic deformation represents an actual change in the distance between atoms or molecules; plastic deformation represents a permanent change in their relative positions. In crystalline materials, this permanent rearrangement consists largely of group displacements of the atoms in the crystal lattice brought about by slip on planes of least resistance, parts of a crystal sliding past one another and in some instances suffering angular displacement. In amorphous materials, the rearrangement appears to take place through the individual shifting from positions of equilibrium of many atoms or molecules, the cause being thermal agitation due to external work and the result appearing as a more or less uniform flow like that of a viscous liquid. It
40
Formulas for Stress and Strain
[CHAP. 3
should be noted that plastic deformation before rupture is much less for biaxial or triaxial tension than for one-way stress; for this reason metals that are ordinarily ductile may prove brittle when thus stressed. 3.6
Creep and Rupture under Long-Time Loading
More materials will creep or flow to some extent and eventually fail under a sustained stress less than the short-time ultimate strength. After a short time at load, the initial creep related to stress redistribution in the structure and strain hardening ceases and the steady state, or viscous creep, predominates. The viscous creep will continue until fracture unless the load is reduced sufficiently, but it is seldom important in materials at temperatures less than 40 to 50% of their absolute melting temperatures. Thus, creep and long-time strength at atmospheric temperatures must sometimes be taken into account in designing members of nonferrous metals and in selecting allowable stresses for wood, plastics, and concrete. Metals. Creep is an important consideration in high-pressure steam and distillation equipment, gas turbines, nuclear reactors, supersonic vehicles, etc. Marin, Odqvist, and Finnie, in Ref. 3, give excellent surveys and list references on creep in metals and structures. Conway (Refs. 4 and 5) discusses the effectiveness of various parametric equations, and Conway and Flagella (Ref. 6) present extensive creep-rupture data for the refractory metals. Odqvist (Ref. 7) discusses the theory of creep and its application to large deformation and stability problems in plates, shells, membranes, and beams and tabulates creep constants for 15 common metals and alloys. Hult (Ref. 8) also discusses creep theory and its application to many structural problems. Penny and Marriott (Ref. 9) discuss creep theories and the design of experiments to verify them. They also discuss the development of several metals for increased resistance to creep at high temperatures as well as polymeric and composite materials at lower temperatures. Reference 10 is a series of papers with extensive references covering creep theory, material properties, and structural problems. Plastics. The literature on the behavior of the many plastics being used for structural or machine applications is too extensive to list here.
Under sustained compressive stress, concrete suffers considerable plastic deformation and may flow for a very long time at stresses less than the ordinary working stress. Continuous flow has
Concrete.
SEC.
3.7]
The Behavior of Bodies under Stress
41
been observed over a period of 10 years, though ordinarily it ceases or becomes imperceptible within 1 or 2 years. The rate of flow is greater for air than for water storage, greater for small than for large specimens, and for moderate stresses increases approximately as the applied stress. On removal of stress, some elastic recovery occurs. Concrete also shows creep under tensile stress, the early creep rate being greater than the flow rate under compression (Refs. 11 and 16). Under very gradually applied loading concrete exhibits an ultimate strength considerably less than that found under short-time loading; in certain compression tests it was found that increasing the time of testing from 1 s to 4 h decreased the unit stress at failure about 30%, most of this decrease occurring between the extremely quick (1 or 2 s) and the conventional (several minutes) testing. This indicates that the compressive stress that concrete can sustain indefinitely may be considerably less than the ultimate strength as determined by a conventional test. On the other hand, the long-time imposition of a moderate loading appears to have no harmful effect; certain tests show that after 10 years of constant loading equal to one-fourth the ultimate strength, the compressive strength of concrete cylinders is practically the same and the modulus of elasticity is considerably greater than for similar cylinders that were not kept under load (Ref. 15). The modulus of rupture of plain concrete also decreases with the time of loading, and some tests indicate that the long-time strength in cross-breaking may be only 55 to 75% of the short-time strength (Ref. 12). Reference 17 is a compilation of 12 papers, each with extensive references, dealing with the effect of volumetric changes on concrete structures. Design modifications to accommodate these volumetric changes are the main thrust of the papers. Wood also yields under sustained stress; the long-time (several years) strength is about 55% of the short-time (several minutes) strength in bending; for direct compression parallel to the grain the corresponding ratio is about 75% (Ref. 2).
Wood.
3.7
Criteria of Elastic Failure and of Rupture
For the purpose of this discussion it is convenient to divide metals into two classes: (1) ductile metals, in which marked plastic deformation commences at a fairly definite stress (yield point, yield strength, or possibly elastic limit) and which exhibit considerable ultimate elongation; and (2) brittle metals, for which the beginning of plastic deformation is not clearly defined and which exhibit little ultimate elongation. Mild steel is typical of the first class, and cast iron is typical of the
42
Formulas for Stress and Strain
[CHAP. 3
second; an ultimate elongation of 5% has been suggested as the arbitrary dividing line between the two classes of metals. A ductile metal is usually considered to have failed when it has suffered elastic failure, i.e., when marked plastic deformation has begun. Under simple uniaxial tension this occurs when the stress reaches a value we will denote by sys, which represents the yield strength, yield point, or elastic limit, according to which one of these is the most satisfactory indication of elastic failure for the material in question. The question arises, when does elastic failure occur under other conditions of stress, such as compression, shear, or a combination of tension, compression, and shear? There are many theories of elastic failure that can be postulated for which the consequences can be seen in the tensile test. When the tensile specimen begins to yield at a tensile stress of sys , the following events occur: 1. The maximum-principal-stress theory: the maximum principal stress reaches the tensile yield strength, sys . 2. The maximum-shear-stress theory (also called the Tresca theory): the maximum shear stress reaches the shear yield strength, 0.5 sys . 3. The maximum-principal-strain theory: the maximum principal strain reaches the yield strain, sys =E. 4. The maximum-strain-energy theory: the strain energy per unit volume reaches a maximum of 0.5 s2ys =E. 5. The maximum-distortion-energy theory (also called the von Mises theory and the Maxwell–Huber–Hencky–von Mises theory): the energy causing a change in shape (distortion) reaches ½ð1 þ nÞ=ð3EÞs2ys . 6. The maximum-octahedral-shear-stress theory: the shear stress acting on each of eight (octahedral) surfaces containing a hydrostatic normal stress, save ¼ ðs1 þ s2 þ s3 Þ=3, reaches a value of p ffiffiffi 2sys =3. It can be shown that this theory yields identical conditions as that provided by the maximum-distortion-energy theory. Of these six theories, for ductile materials, the fifth and sixth are the ones that agree best with experimental evidence. However, the second leads to results so nearly the same and is simpler and more conservative for design applications. Thus, it is more widely used as a basis for design. Failure theories for yield of ductile materials are based on shear or distortion. The maximum-distortion-energy theory equates the distortion energy for a general case of stress to the distortion energy when a
SEC.
3.7]
The Behavior of Bodies under Stress
43
simple tensile specimen yields. In terms of the principal stresses the distortion energy for the general case can be shown to be (see Ref. 59) ud ¼
1þn ½ðs1 s2 Þ2 þ ðs2 s3 Þ2 þ ðs3 s1 Þ2 6E
ð3:7-1Þ
For the simple tensile test, yielding occurs when s1 ¼ sys , and s2 ¼ s3 ¼ 0. From Eq. (3.7-1), this gives a distortion energy at yield of ðud Þy ¼
1þn 2 s 3E ys
ð3:7-2Þ
Equating the energy for the general case, Eq. (3.7-1), to that for yield, Eq. (3.7-2), gives qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 0:5½ðs1 s2 Þ2 þ ðs2 s3 Þ2 þ ðs3 s1 Þ2 ¼ sys ð3:7-3Þ For yield under a single, uniaxial state of stress, the stress would be equated to sys . Thus, for yield, a single, uniaxial stress equivalent to the general state of stress is equated to the left-hand side of Eq. (3.7-3). This equivalent stress is called the von Mises stress, svM , and is given by qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi svM ¼ 0:5½ðs1 s2 Þ2 þ ðs2 s3 Þ2 þ ðs3 s1 Þ2 ð3:7-4Þ Therefore, the maximum-distortion-energy theory predicts elastic failure when the von Mises stress reaches the yield strength. The maximum-octahedral-shear-stress theory yields identical results to that of the maximum-distortion-energy theory (see Ref. 59). Through stress transformation, a stress element can be isolated in which all normal stresses on it are equal. These normal stresses are the averages of the normal stresses of the stress matrix, which are also the averages of the principal stresses and are given by save ¼ 13 ðsx þ sy þ sz Þ ¼ 13 ðs1 þ s2 þ s3 Þ
ð3:7-5Þ
The element with these normal stresses is an octahedron where the eight surfaces are symmetric with respect to the principal axes. The directional cosines of the normals of these p surfaces, relative to p the ffiffiffi ffiffiffi principal axes, are eight combinations of 1= 3 (e.g., one set is 1= 3, pffiffiffi pffiffiffi pffiffiffi pffiffiffi pffiffiffi 1= 3, 1= 3; another is 1= 3, 1 3, 1= 3; etc.). The octahedron is as shown in Fig. 3.1. The shear stresses on these surfaces are also equal, called the octahedral shear stresses, and are given by qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi toct ¼ 13 ðs1 s2 Þ2 þ ðs2 s3 Þ2 þ ðs3 s1 Þ2 ð3:7-6Þ
44
Formulas for Stress and Strain
[CHAP. 3
Figure 3.1 Octahedral surfaces containing octahedral shear stresses (shown relative to the principal axes, with only one set of stresses displayed).
Again, for the simple tensile test, yield occurs when s1 ¼ sys , and s2 ¼ s3 ¼ 0. From Eq. (3.7-6), this gives an octahedral shear stress at yield of pffiffiffi 2 s ð3:7-7Þ ðtoct Þy ¼ 3 ys Equating Eqs. (3.7-6) and (3.7-7) results in Eq. (3.7-3) again, proving that the maximum-octahedral-shear-stress theory is identical to the maximum-distortion-energy theory. The maximum-shear-stress theory equates the maximum shear stress for a general state of stress to the maximum shear stress obtained when the tensile specimen yields. If the principal stresses are ordered such that s1 5 s2 5 s3 , the maximum shear stress is given by 0:5ðs1 s3 Þ (see Sec. 2.3, Eq. 2.3-25). The maximum shear stress obtained when the tensile specimen yields is 0.5 sys . Thus, the condition for elastic failure for the maximum-shear-stress theory isy s1 s3 ¼ sys
ð3:7-8Þ
The criteria just discussed concern the elastic failure of material. Such failure may occur locally in a member and may do no real damage if the volume of material affected is so small or so located as to have y Plane stress problems are encountered quite often where the principal stresses are found from Eq. (2.3-23), which is sp ¼
ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi r sx þ sy sx sy 2 þ t2xy 2 2
This yields only two of the three principal stresses. The third principal stress for plane stress is zero. Once the three principal stresses are determined, they can be ordered according to s1 5 s2 5 s3 and then Eq. (3.7-8) can be employed.
SEC.
3.7]
The Behavior of Bodies under Stress
45
only negligible influence on the form and strength of the member as a whole. Whether or not such local overstressing is significant depends upon the properties of the material and the conditions of service. Fatigue properties, resistance to impact, and mechanical functioning are much more likely to be affected than static strength, and a degree of local overstressing that would constitute failure in a high-speed machine part might be of no consequence whatever in a bridge member. A brittle material cannot be considered to have definitely failed until it has broken, which can occur either through a tensile fracture, when the maximum tensile stress reaches the ultimate strength, or through what appears to be a shear fracture, when the maximum compressive stress reaches a certain value. The fracture occurs on a plane oblique to the maximum compressive stress but not, as a rule, on the plane of maximum shear stress, and so it cannot be considered to be purely a shear failure (see Ref. 14). The results of some tests on glass and Bakelite (Ref. 26) indicate that for these brittle materials either the maximum stress or the maximum strain theory affords a satisfactory criterion of rupture while neither the maximum shear stress nor the constant energy of distortion theory does. These tests also indicate that strength increases with rate of stress application and that the increase is more marked when the location of the most stressed zone changes during the loading (pressure of a sphere on a flat surface) than when this zone is fixed (axial tension). Another failure theory that is applicable to brittle materials is the Coulomb–Mohr theory of failure. Brittle materials have ultimate compressive strengths suc greater than their ultimate tensile strengths sut , and therefore both a uniaxial tensile test and a uniaxial compressive test must be run to use the Coulomb–Mohr theory. First we draw on a single plot both Mohr’s stress circle for the tensile test at the instant of failure and Mohr’s stress circle for the compressive test at the instant of failure; then we complete a failure envelope simply by drawing a pair of tangent lines to the two circles, as shown in Fig. 3.2. Failure under a complex stress situation is expected if the largest of the three Mohr circles for the given situation touches or extends outside the envelope just described. If all normal stresses are tensile, the results coincide with the maximum stress theory. For a condition where the three principal stresses are sA , sB , and sC , as shown in Fig. 3.2, failure is being approached but will not take place unless the dashed circle passing through sA and sC reaches the failure envelope. The accurate prediction of the breaking strength of a member composed of brittle metal requires a knowledge of the effect of form and scale, and these effects are expressed by the rupture factor (see Sec. 3.11). In addition, what has been said here concerning brittle metals applies also to any essentially isotropic brittle material. Thus far, our discussion of failure has been limited to isotropic materials. For wood, which is distinctly anisotropic, the possibility of
46
Formulas for Stress and Strain
[CHAP. 3
Figure 3.2
failure in each of several ways and directions must be taken into account, viz.: (1) by tension parallel to the grain, which causes fracture; (2) by tension transverse to the grain, which causes fracture; (3) by shear parallel to the grain, which causes fracture; (4) by compression parallel to the grain, which causes gradual buckling of the fibers usually accompanied by a shear displacement on an oblique plane; (5) by compression transverse to the grain, which causes sufficient deformation to make the part unfit for service. The unit stress producing each of these types of failure must be ascertained by suitable tests (Ref. 2). Another anisotropic class of material of consequence is that of the composites. It is well known that composite members (see Secs. 7.3, 8.2, and Appendix C), such as steel reinforced concrete beams, more effectively utilize the more expensive, higher-strength materials in high-stress areas and the less expensive, lower-strength materials in the low-stress areas. Composite materials accomplish the same effect at microstructural and macrostructural levels. Composite materials come in many forms, but are generally formulated by embedding a reinforcement material in the form of fibers, flakes, particles, or laminations, in a randomly or orderly oriented fashion within a base matrix of polymeric, metallic, or ceramic material. For more detail properties of composites, see Ref. 60.
3.8
Fatigue
Practically all materials will break under numerous repetitions of a stress that is not as great as the stress required to produce immediate rupture. This phenomenon is known as fatigue.
SEC.
3.8]
The Behavior of Bodies under Stress
47
Over the past 100 years the effects of surface condition, corrosion, temperature, etc., on fatigue properties have been well documented, but only in recent years has the microscopic cause of fatigue damage been attributed to cyclic plastic flow in the material at the source of a fatigue crack (crack initiation) or at the tip of an existing fatigue crack (crack propagation; Ref. 20). The development of extremely sensitive extensometers has permitted the separation of elastic and plastic strains when testing axially loaded specimens over short gage lengths. With this instrumentation it is possible to determine whether cyclic loading is accompanied by significant cyclic plastic strain and, if it is, whether the cyclic plastic strain continues at the same level, increases, or decreases. Sandor (Ref. 44) discusses this instrumentation and its use in detail. It is not feasible to reproduce here even a small portion of the fatigue data available for various engineering materials. The reader should consult materials handbooks, manufacturers’ literature, design manuals, and texts on fatigue. See Refs. 44 to 48. Some of the more important factors governing fatigue behavior in general will be outlined in the following material. Most data concerning the number of cycles to failure are presented in the form of an S N curve where the cyclic stress amplitude is plotted versus the number of cycles to failure. This generally leads to a straight-line log–log plot if we account for the scatter in the data. For ferrous metals a lower limit exists on the stress amplitude and is called the fatigue limit, or endurance limit. This generally occurs at a life of from 105 to 107 cycles of reversed stress, and we assume that stresses below this limit will not cause failure regardless of the number of repetitions. With the ability to separate elastic and plastic strains accurately, there are instances when a plot of plastic-strain amplitudes versus N and elastic-strain amplitudes versus N will reveal more useful information (Refs. 44 and 45). Number of cycles to failure.
Method of loading and size of specimen. Uniaxial stress can be
produced by axial load, bending, or a combination of both. In flatplate bending, only the upper and lower surfaces are subjected to the full range of cyclic stress. In rotating bending, all surface layers are similarly stressed, but in axial loading, the entire cross section is subjected to the same average stress. Since fatigue properties of a material depend upon the statistical distribution of defects throughout the specimen, it is apparent that the three methods of loading will produce different results. In a similar way, the size of a bending specimen will affect the fatigue behavior while it will have little effect on an axially loaded
48
Formulas for Stress and Strain
[CHAP. 3
specimen. Several empirical formulas have been proposed to represent the influence of size on a machine part or test specimen in bending. For steel, Moore (Ref. 38) suggests the equation 0:016 0:016 00 s0e 1 1 ¼ s e d0 d00 where s0e is the endurance limit for a specimen of diameter d0 and s00e is the endurance limit for a specimen of diameter d00. This formula was based on test results obtained with specimens from 0.125 to 1.875 inches in diameter and shows good agreement within that size range. Obviously it cannot be used for predicting the endurance limit of very small specimens. The few relevant test results available indicate a considerable decrease in endurance limit for very large diameters (Refs. 22–24). Fatigue failures occur at stress levels less than those necessary to produce the gross yielding which would blunt the sharp rise in stress at a stress concentration. It is necessary, therefore, to apply the fatigue strengths of a smooth specimen to the peak stresses expected at the stress concentrations unless the size of the stress-concentrating notch or fillet approaches the grain size or the size of an anticipated defect in the material itself (see Factor of stress concentration in fatigue in Sec. 3.10). References 40 and 41 discuss the effect of notches on low-cycle fatigue. Stress concentrations.
Surface roughness constitutes a kind of stress raiser. Discussion of the effect of surface coatings and platings is beyond the scope of this book (see Refs. 28 and 36).
Surface conditions.
Corrosion fatigue. Under the simultaneous action of corrosion and
repeated stress, the fatigue strength of most metals is drastically reduced, sometimes to a small fraction of the strength in air, and a true endurance limit can no longer be said to exist. Liquids and gases not ordinarily thought of as especially conducive to corrosion will often have a very deleterious effect on fatigue properties, and resistance to corrosion is more important than normal fatigue strength in determining the relative rating of different metals (Refs. 24, 25, and 31). Range of stress. Stressing a ductile material beyond the elastic limit
or yield point in tension will raise the elastic limit for subsequent cycles but lower the elastic limit for compression. The consequence of this Bauschinger effect on fatigue is apparent if one accepts the statement that fatigue damage is a result of cyclic plastic flow; i.e.,
SEC.
3.8]
The Behavior of Bodies under Stress
49
Figure 3.3
if the range of cyclic stress is reduced sufficiently, higher peak stresses can be accepted without suffering continuing damage. Various empirical formulas for the endurance limit corresponding to any given range of stress variation have been suggested, the most generally accepted of which is expressed by the Goodman diagram or some modification thereof. Figure 3.3 shows one method of constructing this diagram. In each cycle, the stress varies from a maximum value smax to a minimum value smin , either of which is plus or minus according to whether it is tensile or compressive. The mean stress is sm ¼ 12 ðsmax þ smin Þ and the alternating stress is sa ¼ 12 ðsmax smin Þ the addition and subtraction being algebraic. With reference to rectangular axes, sm is measured horizontally and sa vertically. Obviously when sm ¼ 0, the limiting value of sa is the endurance limit for fully reversed stress, denoted here by se. When sa ¼ 0, the limiting value of sm is the ultimate tensile strength, denoted here by su. Points A and B on the axes are thus located. According to the Goodman theory, the ordinate to a point on the straight line AB represents the maximum alternating stress sa that can be imposed in conjunction with the corresponding mean stress sm . Any point above AB represents a stress condition that would eventually cause failure; any point below AB represents a stress condition with more or less margin of safety. A more conservative construction, suggested by Soderberg (Ref. 13), is to move point B back to sys , the yield strength. A less conservative but sometimes preferred construction, proposed by Gerber, is to replace the straight line by the parabola.
50
Formulas for Stress and Strain
[CHAP. 3
The Goodman diagrams described can be used for steel and for aluminum and titanium alloys, but for cast iron many test results fall below the straight line AB and the lower curved line, suggested by Smith (Ref. 21), is preferred. Test results for magnesium alloys also sometimes fall below the straight line. Figure 3.3 represents conditions where sm is tensile. If sm is compressive, sa is increased; and for values of sm less than the compression yield strength, the relationship is represented approximately by the straight line AB extended to the left with the same slope. When the mean stress and alternating stress are both torsional, sa is practically constant until sm exceeds the yield strength in shear; and for alternating bending combined with mean torsion, the same thing is true. But when sm is tensile and sa is torsional, sa diminishes as sm increases in almost the manner represented by the Goodman line. When stress concentration is to be taken into account, the accepted practice is to apply Kf (or Kt if Kf is not known) to sa only, not to sm (for Kt and Kf , see Sec. 3.10). Residual stress. Since residual stresses, whether deliberately intro-
duced or merely left over from manufacturing processes, will influence the mean stress, their effects can be accounted for. One should be careful, however, not to expect the beneficial effects of a residual stress if during the expected life of a structure it will encounter overloads sufficient to change the residual-stress distribution. Sandor (Ref. 44) discusses this in detail and points out that an occasional overload might be beneficial in some cases. The several modified forms of the Goodman diagram are used for predicting the stress levels which will form cracks, but other more extensive plots such as the Haigh diagram (Ref. 45) can be used to predict in addition the stress levels for which cracks, once formed, will travel, fatigue lives, etc. No one of the theories of failure in Sec. 3.7 can be applied to all fatigue loading conditions. The maximum-distortionenergy theory seems to be conservative in most cases, however. Reference 18 gives a detailed description of an acceptable procedure for designing for fatigue under conditions of combined stress. The procedure described also considers the effect of mean stress on the cyclic stress range. Three criteria for failure are discussed: gross yielding, crack initiation, and crack propagation. An extensive discussion of fatigue under combined stress is found in Refs. 27, 31, and 45.
Combined stress.
A very important question and one that has been given much attention is the influence of previous stressing on fatigue
Stress history.
SEC.
3.9]
The Behavior of Bodies under Stress
51
strength. One theory that has had considerable acceptance is the linear damage law (Miner in Ref. 27); here the assumption is made that the damage produced by repeated stressing at any level is directly proportional to the number of cycles. Thus, if the number of cycles producing failure (100% damage) at a stress range s1 is N1 , then the proportional damage produced by N cycles of the stress is N=N1 and stressing at various stress levels for various numbers of cycles causes cumulative damage equal to thePsummation of such fractional values. Failure occurs, therefore, when N=N1 ¼ 1. The formula implies that the effect of a given number of cycles is the same, whether they are applied continuously or intermittently, and does not take into account the fact that for some metals understressing (stressing below the endurance limit) raises the endurance limit. The linear damage law is not reliable for all stress conditions, and various modifications have been proposed, such as replacing 1 in the formula by a quantity x whose numerical value, either more or less than unity, must be determined experimentally. Attempts have been made to develop a better theory (e.g., Corten and Dolan, Freudenthal and Gumbel, in Ref. 32). Though all the several theories are of value when used knowledgeably, it does not appear that as yet any generally reliable method is available for predicting the life of a stressed part under variable or random loading. (See Refs. 19 and 39.) See Refs. 44 and 45 for a more detailed discussion. A modification of the foil strain gage called an S N fatigue life gage (Refs. 33 and 34) measures accumulated plastic deformation in the form of a permanent change in resistance. A given total change in resistance can be correlated with the damage necessary to cause a fatigue failure in a given material. 3.9
Brittle Fracture
Brittle fracture is a term applied to an unexpected brittle failure of a material such as low-carbon steel where large plastic strains are usually noted before actual separation of the part. Major studies of brittle fracture started when failures such as those of welded ships operating in cold seas led to a search for the effect of temperature on the mode of failure. For a brittle fracture to take place the material must be subjected to a tensile stress at a location where a crack or other very sharp notch or defect is present and the temperature must be lower than the so-called transition temperature. To determine a transition temperature for a given material, a series of notched specimens is tested under impact loading, each at a different temperature, and the ductility or the energy required to cause fracture is noted. There will be a limited range of temperatures over which the ductility or fracture energy will drop significantly. Careful examination of the
52
Formulas for Stress and Strain
[CHAP. 3
fractured specimens will show that the material at the root of the notch has tried to contract laterally. Where the fracture energy is large, there is evidence of a large lateral contraction; and where the fracture energy is small, the lateral contraction is essentially zero. In all cases the lateral contraction is resisted by the adjacent less stressed material. The deeper and sharper cracks have relatively more material to resist lateral contraction. Thicker specimens have a greater distance over which to build up the necessary triaxial tensile stresses that lead to a tensile failure without producing enough shear stress to cause yielding. Thus, the term transition temperature is somewhat relative since it depends upon notch geometry as well as specimen size and shape. Since yielding is a flow phenomenon, it is apparent that rate of loading is also important. Static loading of sufficient intensity may start a brittle fracture, but it can continue under much lower stress levels owing to the higher rate of loading. The ensuing research in the field of fracture mechanics has led to the development of both acceptable theories and experimental techniques, the discussion of which is beyond the scope of this book. Users should examine Refs. 49–58 for information and for extensive bibliographies. 3.10
Stress Concentration
The distribution of elastic stress across the section of a member may be nominally uniform or may vary in some regular manner, as illustrated by the linear distribution of stress in flexure. When the variation is abrupt so that within a very short distance the intensity of stress increases greatly, the condition is described as stress concentration. It is usually due to local irregularities of form such as small holes, screw threads, scratches, and similar stress raisers. There is obviously no hard and fast line of demarcation between the rapid variation of stress brought about by a stress raiser and the variation that occurs in such members as sharply curved beams, but in general the term stress concentration implies some form of irregularity not inherent in the member as such but accidental (tool marks) or introduced for some special purpose (screw thread). The maximum intensity of elastic stress produced by many of the common kinds of stress raisers can be ascertained by mathematical analysis, photoelastic analysis, or direct strain measurement and is usually expressed by the stress concentration factor. This term is defined in Appendix B, but its meaning may be made clearer by an example. Consider a straight rectangular beam, originally of uniform breadth b and depth D, which has had cut across the lower face a fairly sharp transverse V-notch of uniform depth h, making the net depth of the beam section at that point D h. If now the beam is subjected to a uniform bending moment M , the nominal fiber stress at the root of the
SEC.
3.10]
The Behavior of Bodies under Stress
53
notch may be calculated by ordinary flexure formula s ¼ Mc=I, which here reduces to s ¼ 6M =½bðD hÞ2 . But the actual stress s0 is very much greater than this because of the stress concentration that occurs at the root of the notch. The ratio s0 =s, actual stress divided by nominal stress, is the stress concentration factor Kt for this particular case. Values of Kt for a number of common stress raisers are given in Table 17.1. The most complete single source for numerical values of stress concentration factors is Peterson (Ref. 42). It also contains an extensive bibliography. The abrupt variation and high local intensity of stress produced by stress raisers are characteristics of elastic behavior. The plastic yielding that occurs on overstressing greatly mitigates stress concentration even in relatively brittle materials and causes it to have much less influence on breaking strength than might be expected from a consideration of the elastic stresses only. The practical significance of stress concentration therefore depends on circumstances. For ductile metal under static loading it is usually (though not always) of little or no importance; for example, the high stresses that occur at the edges of rivet holes in structural steel members are safely ignored, the stress due to a tensile load being assumed uniform on the net section. (In the case of eyebars and similar pin-connected members, however, a reduction of 25% in allowable stress on the net section is recommended.) For brittle material under static loading, stress concentration is often a serious consideration, but its effect varies widely and cannot be predicted either from Kt or from the brittleness of the material (see Ref. 35). What may be termed the stress concentration factor at rupture, or the strength reduction factor, represents the significance of stress concentration for static loading. This factor, which will be denoted by Kr is the ratio of the computed stress at rupture for a plain specimen to the computed stress at rupture for the specimen containing the stress raiser. For the case just described, it would be the ratio of the modulus of rupture of the plain beam to that of the notched beam, the latter being calculated for the net section. Kr is therefore a ratio of stresses, one or both of which may be fictitious, but is nonetheless a measure of the strength-reducing effect of stress concentration. Some values of Kr are given in Table 17 of Ref. 1. It is for conditions involving fatigue that stress concentration is most important. Even the most highly localized stresses, such as those produced by small surface scratches, may greatly lower the apparent endurance limit, but materials vary greatly in notch sensitivity, as susceptibility to this effect is sometimes called. Contrary to what might be expected, ductility (as ordinarily determined by axial testing) is not a measure of immunity to stress concentration in fatigue; for example, steel is much more susceptible than cast iron. What may be
54
Formulas for Stress and Strain
[CHAP. 3
termed the fatigue stress concentration factor Kf is the practical measure of notch sensitivity. It is the ratio of the endurance limit of a plain specimen to the nominal stress at the endurance limit of a specimen containing the stress raiser. A study of available experimental data shows that Kf is almost always less, and often significantly less, than Kt , and various methods for estimating Kf from Kt have been proposed. Neuber (Ref. 37) proposes the formula Kf ¼ 1 þ
Kt 1 pffiffiffiffiffiffiffiffiffi 1 þ p r0 =r=ðp oÞ
ð3:10-1Þ
where o is the flank angle of the notch (called y in Table 17.1), r is the radius of curvature (in inches) at the root of the notch (called r in Table 17.1), and r0 is a dimension related to the grain size, or size of some type of basic building block, of the material and may be taken as 0.0189 in for steel. All the methods described are valuable and applicable within certain limitations, but none can be applied with confidence to all situations (Ref. 29). Probably none of them gives sufficient weight to the effect of scale in the larger size range. There is abundant evidence to show that the significance of stress concentration increases with size for both static and repeated loading, especially the latter. An important fact concerning stress concentration is that a single isolated notch or hole has a worse effect than have a number of similar stress raisers placed close together; thus, a single V-groove reduces the strength of a part more than does a continuous screw thread of almost identical form. The deleterious effect of an unavoidable stress raiser can, therefore, be mitigated sometimes by juxtaposing additional form irregularities of like nature, but the actual superposition of stress raisers, such as the introduction of a small notch in a fillet, may result in a stress concentration factor equal to or even exceeding the product of the factors for the individual stress raisers (Refs. 30 and 43). 3.11
Effect of Form and Scale on Strength; Rupture Factor
It has been pointed out (Sec. 3.7) that a member composed of brittle material breaks in tension when the maximum tensile stress reaches the ultimate strength or in shear when the maximum compressive stress reaches a certain value. In calculating the stress at rupture in such a member it is customary to employ an elastic-stress formula; thus the ultimate fiber stress in a beam is usually calculated by the ordinary flexure formula. It is known that the result (modulus of rupture) is not a true stress, but it can be used to predict the strength of a similar beam of the same material. However, if another beam of
SEC.
3.11]
The Behavior of Bodies under Stress
55
the same material but of different cross section, span=depth ratio, size, or manner of loading and support is tested, the modulus of rupture will be found to be different. (The effect of the shape of the section is often taken into account by the form factor, and the effects of the span=depth ratio and manner of loading are recognized in the testing procedure.) Similarly, the calculated maximum stress at rupture in a curved beam, flat plate, or torsion member is not equal to the ultimate strength of the material, and the magnitude of the disparity will vary greatly with the material, form of the member, manner of loading, and absolute scale. In order to predict accurately the breaking load for such a member, it is necessary to take this variation into account, and the rupture factor (defined in Appendix B) provides a convenient means of doing so. Values of the rupture factor for a number of materials and types of members are given in Table 18 of Ref. 1. On the basis of many experimental determinations of the rupture factor (Ref. 35) the following generalizations may be made: 1. The smaller the proportional part of the member subjected to high stress, the larger the rupture factor. This is exemplified by the facts that a beam of circular section exhibits a higher modulus of rupture than a rectangular beam and that a flat plate under a concentrated center load fails at a higher computed stress than one uniformly loaded. The extremes in this respect are, on the one hand, a uniform bar under axial tension for which the rupture factor is unity and, on the other hand, a case of severe stress concentration such as a sharply notched bar for which the rupture factor may be indefinitely large. 2. In the flexure of statically indeterminate members, the redistribution of bending moments that occurs when plastic yielding starts at the most highly stressed section increases the rupture factor. For this reason a flat plate gives a higher value than a simple beam, and a circular ring gives a higher value than a portion of it tested as a statically determinate curved beam. 3. The rupture factor seems to vary inversely with the absolute scale for conditions involving abrupt stress variation, which is consistent with the fact (already noted) that for cases of stress concentration both Kr and Kf diminish with the absolute scale. 4. As a rule, the more brittle the material, the more nearly all rupture factors approach unity. There are, however, many exceptions to this rule. It has been pointed out (Sec. 3.10) that immunity to notch effect even under static loading is not always proportional to ductility. The practical significance of these facts is that for a given material and given factor of safety, some members may be designed with a
56
Formulas for Stress and Strain
[CHAP. 3
much higher allowable stress than others. This fact is often recognized in design; for example, the allowable stress for wooden airplane spars varies according to the form factor and the proportion of the stress that is flexural. What has been said here pertains especially to comparatively brittle materials, i.e., materials for which failure consists in fracture rather than in the beginning of plastic deformation. The effect of form on the ultimate strength of ductile members is less important, although even for steel the allowable unit stress is often chosen with regard to circumstances such as those discussed previously. For instance, in gun design the maximum stress is allowed to approach and even exceed the nominal elastic limit, the volume of material affected being very small, and in structural design extreme fiber stresses in bending are permitted to exceed the value allowed for axial loading. In testing, account must be taken of the fact that some ductile metals exhibit a higher ultimate strength when fracture occurs at a reduced section such as would be formed in a tensile specimen by a concentric groove or notch. Whatever effect of stress concentration may remain during plastic deformation is more than offset by the supporting action of the shoulders, which tends to prevent the normal ‘‘necking down.’’ 3.12
Prestressing
Parts of an elastic system, by accident or design, may have introduced into them stresses that cause and are balanced by opposing stresses in other parts, so that the system reaches a state of stress without the imposition of any external load. Examples of such initial, or locked-up, stresses are the temperature stresses in welded members, stresses in a statically indeterminate truss due to tightening or ‘‘rigging’’ some of the members by turnbuckles, and stresses in the flange couplings of a pipeline caused by screwing down the nuts. The effects of such prestressing upon the rigidity and strength of a system will now be considered, the assumption being made that prestressing is not so severe as to affect the properties of the material. In discussing this subject it is necessary to distinguish two types of systems, viz. one in which the component parts can sustain reversal of stress and one in which at least some of the component parts cannot sustain reversal of stress. Examples of the first type are furnished by a solid bar and by a truss, all members of which can sustain either tension or compression. Examples of the second type are furnished by the bolt-flange combination mentioned and by a truss with wire diagonals that can take tension only. For the first type of system, prestressing has no effect on initial rigidity. Thus a plain bar with locked-up temperature stresses will exhibit the same modulus of elasticity as a similar bar from which
SEC.
3.12]
The Behavior of Bodies under Stress
57
these stresses have been removed by annealing; two prestressed helical springs arranged in parallel, the tension in one balancing the compression in the other, will deflect neither more nor less than the same two springs similarly placed without prestressing. Prestressing will lower the elastic limit (or allowable load, or ultimate strength) provided that in the absence of prestressing all parts of the system reach their respective elastic limits (or allowable loads, or ultimate strengths) simultaneously. But if this relation between the parts does not exist, then prestressing may raise any or all of these quantities. One or two examples illustrating each condition may make this clear. Consider first a plain bar that is to be loaded in axial tension. If there are no locked-up stresses, then (practically speaking) all parts of the bar reach their allowable stress, elastic limit, and ultimate strength simultaneously. But if there are locked-up stresses present, then the parts in which the initial tension is highest reach their elastic limit before other parts and the elastic limit of the bar as a whole is thus lowered. The load at which the allowable unit stress is first reached is similarly lowered, and the ultimate strength may also be reduced; although if the material is ductile, the equalization of stress that occurs during elongation will largely prevent this. As an example of the second condition (all parts do not simultaneously reach the elastic limit or allowable stress) consider a thick cylinder under internal pressure. If the cylinder is not prestressed, the stress at the interior surface reaches the elastic limit first and so governs the pressure that may be applied. But if the cylinder is prestressed by shrinking on a jacket or wrapping with wire under tension, as is done in gun construction, then the walls are put into an initial state of compression. This compressive stress also is greatest at the inner surface, and the pressure required to reverse it and produce a tensile stress equal to the elastic limit is much greater than before. As another example, consider a composite member comprising two rods of equal length, one aluminum and the other steel, that are placed side by side to jointly carry a tensile load. For simplicity, it will be assumed that the allowable unit stresses for the materials are the same. Because the modulus of elasticity of the steel is about three times that of the aluminum, it will reach the allowable stress first and at a total load less than the sum of the allowable loads for the bars acting separately. But if the composite bar is properly prestressed, the steel being put into initial compression and the aluminum into initial tension (the ends being in some way rigidly connected to permit this), then on the application of a tensile load the two bars will reach the allowable stress simultaneously and the load-carrying capacity of the combination is thus greater than before. Similarly the elastic limit and
58
Formulas for Stress and Strain
[CHAP. 3
sometimes the ultimate strength of a composite member may be raised by prestressing. In a system of the second type (in which all parts cannot sustain stress reversal) prestressing increases the rigidity for any load less than that required to produce stress reversal. The effect of prestressing up to that point is to make the rigidity of the system the same as though all parts were effective. Thus in the case of the truss with wire diagonals it is as though the counterwires were taking compression; in the case of the flange-bolt combination it is as though the flanges were taking tension. (If the flanges are practically rigid in comparison with the bolts, there is no deformation until the applied load exceeds the bolt tension and so the system is rigid.) When the applied load becomes large enough to cause stress reversal (to make the counterwires go slack or to separate the flanges), the effect of prestressing disappears and the system is neither more nor less rigid than a similar one not prestressed provided, of course, none of the parts has been overstressed. The elastic limit (or allowable load, or ultimate strength) of a system of this type is not affected by prestressing unless the elastic limit (or allowable load, or ultimate strength) of one or more of the parts is reached before the stress reversal occurs. In effect, a system of this type is exactly like a system of the first type until stress reversal occurs, after which all effects of prestressing vanish. The effects of prestressing are often taken advantage of, notably in bolted joints (flanges, cylinder heads, etc.), where high initial tension in the bolts prevents stress fluctuation and consequent fatigue, and in prestressed reinforced-concrete members, where the initially compressed concrete is enabled, in effect, to act in tension without cracking up to the point of stress reversal. The example of the prestressed thick cylinder has already been mentioned. 3.13
Elastic Stability
Under certain circumstances the maximum load a member will sustain is determined not by the strength of the material but by the stiffness of the member. This condition arises when the load produces a bending or a twisting moment that is proportional to the corresponding deformation. The most familiar example is the Euler column. When a straight slender column is loaded axially, it remains straight and suffers only axial compressive deformation under small loads. If while thus loaded it is slightly deflected by a transverse force, it will straighten after removal of that force. But there is obviously some axial load that will just hold the column in the deflected position, and since both the bending moment due to the load and the resisting moment due to the stresses are directly proportional to the deflection,
SEC.
3.14]
The Behavior of Bodies under Stress
59
the load required thus to hold the column is independent of the amount of the deflection. If this condition of balance exists at stresses less than the elastic limit, the condition is called elastic stability and the load that produces this condition is called the critical load. Any increase of the load beyond this critical value is usually attended by immediate collapse of the member. It is the compressive stresses within long, thin sections of a structure that can cause instabilities. The compressive stress can be elastic or inelastic and the instability can be global or local. Global instabilities can cause catastrophic failure, whereas local instabilities may cause permanent deformation but not necessarily a catastrophic failure. For the Euler column, when instability occurs, it is global since the entire cross section is involved in the deformation. Localized buckling of the edges of the flange in compression of a wide-flange I-beam in bending can occur. Likewise, the center of the web of a transversely loaded I-beam or plate girder in bending undergoes pure shear where along the diagonal (45 ) compressive stresses are present and localized buckling is possible. Other examples of elastic stability are afforded by a thin cylinder under external pressure, a thin plate under edge compression or edge shear, and a deep thin cantilever beam under a transverse end load applied at the top surface. Some such elements, unlike the simple column described previously, do not fail under the load that initiates elastic buckling but demonstrate increasing resistance as the buckling progresses. Such postbuckling behavior is important in many problems of shell design. Elastic stability is discussed further in Chap. 15, and formulas for the critical loads for various members and types of loadings are given in Tables 15.1 and 15.2.
3.14
References
1. Roark, R. J. ‘‘Formulas for Stress and Strain,’’ 4th ed., McGraw-Hill, 1965. 2. ‘‘Wood Handbook,’’ Forest Products Laboratory, U.S. Dept. of Agriculture, 1987. 3. Abramson, H. N., H. Leibowitz, J. M. Crowley, and S. Juhasz (eds.): ‘‘Applied Mechanics Surveys,’’ Spartan Books, 1966. 4. Conway, J. B.: ‘‘Stress-rupture Parameters: Origin, Calculation, and Use,’’ Gordon and Breach Science Publishers, 1969. 5. Conway, J. B.: ‘‘Numerical Methods for Creep and Rupture Analyses,’’ Gordon and Breach Science Publishers, 1967. 6. Conway, J. B., and P. N. Flagella: ‘‘Creep-rupture Data for the Refractory Metals to High Temperatures,’’ Gordon and Breach Science Publishers, 1971. 7. Odqvist, F. K. G.: ‘‘Mathematical Theory of Creep and Creep Rupture,’’ Oxford University Press, 1966. 8. Hult, J. A. H.: ‘‘Creep in Engineering Structures,’’ Blaisdell, 1966. 9. Penny, R. K., and D. L. Marriott: ‘‘Design for Creep,’’ McGraw-Hill, 1971. 10. Smith, A. I., and A. M. Nicolson (eds.): ‘‘Advances in Creep Design, The A. E. Johnson Memorial Volume,’’ Applied Science Publishers, 1971. 11. Davis, R. E., H. E. Davis, and J. S. Hamilton: Plastic Flow of Concrete under Sustained Stress, Proc. ASTM, vol. 34, part II, p. 854, 1934.
60
Formulas for Stress and Strain
[CHAP. 3
12. Report of Committee on Materials of Construction, Bull. Assoc. State Eng. Soc., July 1934. 13. Soderberg, R.: Working Stresses, ASME Paper A-106, J. Appl. Mech., vol. 2, no. 3, 1935. 14. Na´ dai, A.: Theories of Strength., ASME Paper APM 55-15, J. Appl. Mech., vol. 1, no. 3, 1933. 15. Washa, G. W., and P. G. Fluck: Effect of Sustained Loading on Compressive Strength and Modulus of Elasticity of Concrete, J. Am. Concr. Inst., vol. 46, May 1950. 16. Neville, A. M.: ‘‘Creep of Concrete: Plain, Reinforced, and Prestressed,’’ NorthHolland, 1970. 17. Designing for Effects of Creep, Shrinkage, Temperature in Concrete Structures, Am. Concr. Inst. Publ. SP-27, 1971. 18. ‘‘Fatigue Design Handbook,’’ Society of Automotive Engineers, Inc., 1968. 19. Structural Fatigue in Aircraft, ASTM Spec. Tech. Publ. 404, 1965. 20. Fatigue Crack Propagation, ASTM Spec. Tech. Publ. 415, 1966. 21. Smith. J. O.: The Effect of Range of Stress on Fatigue Strength, Univ. Ill., Eng. Exp. Sta. Bull. 334, 1942. 22. Horger, O. J., and H. R. Neifert: Fatigue Strength of Machined Forgings 6 to 7 Inches in Diameter, Proc. ASTM, vol. 39, 1939. 23. Eaton, F. C.: Fatigue Tests of Large Alloy Steel Shafts; Symposium on Large Fatigue Testing Machines and their Results, ASTM Spec. Tech. Publ. 216, 1957. 24. Jiro, H., and A. Junich: Studies on Rotating Beam Fatigue of Large Mild Steel Specimens, Proc. 9th Jap. Natl. Congr. Appl. Mech., 1959. 25. Gould, A. J.: Corrosion Fatigue (in Ref. 32). 26. Weibull, W.: Investigations into Strength Properties of Brittle Materials, Proc. B. Swed. Inst. Eng. Res., no. 149, 1938. 27. Sines, George, and J. L. Waisman (eds.): ‘‘Metal Fatigue,’’ McGraw-Hill, 1959. 28. Heywood, R. B.: ‘‘Designing against Fatigue of Metals,’’ Reinhold, 1962. 29. Yen, C. S., and T. J. Dolan: A Critical Review of the Criteria for Notch Sensitivity in Fatigue of Metals, Univ. Ill., Exp. Sta. Bull. 398, 1952. 30. Mowbray, A. Q., Jr.: The Effect of Superposition of Stress Raisers on Members Subjected to Static or Repeated Loads, Proc. Soc. Exp. Stress Anal, vol. 10, no. 2, 1953. 31. Forrest, P. G.: ‘‘Fatigue of Metals,’’ Pergamon Press, Addison-Wesley Series in Metallurgy and Materials, 1962. 32. International Conference on Fatigue of Metals, Institution of Mechanical Engineers, London, and American Society of Mechanical Engineers, New York, 1956. 33. Harting, D. R.: The -S/N- Fatigue Life Gage: A Direct Means of Measuring Cumulative Fatigue Damage, Exp. Mech., vol. 6, no. 2, February 1966. 34. Descriptive literature, Micro-Measurements, Inc., Romulus, Mich. 35. Roark, R. J., R. S. Hartenberg, and R. Z. Williams: The Influence of Form and Scale on Strength, Univ. Wis. Exp. Ste. Bull. 84, 1938. 36. Battelle Memorial Institute: ‘‘Prevention of Fatigue of Metals,’’ John Wiley & Sons, 1941. 37. Neuber, H.: ‘‘Theory of Notch Stresses,’’ J. W. Edwards, Publisher, Incorporated, 1946. 38. Moore, H. F.: A Study of Size Effect and Notch Sensitivity in Fatigue Tests of Steel, Proc. Am. Soc. Test. Mater., vol. 45, 1945. 39. Metal Fatigue Damage: Mechanism, Detection, Avoidance, and Repair, ASTM Spec. Tech. Publ. 495, 1971. 40. Cyclic Stress-Strain Behavior: Analysis, Experimentation, and Failure Prediction, ASTM Spec. Tech. Publ. 519, 1973. 41. Effect of Notches on Low-Cycle Fatigue: A Literature Survey, ASTM Spec. Tech. Publ. 490, 1972. 42. Peterson, H. E.: ‘‘Stress Concentration Factors,’’ John Wiley & Sons, 1974. 43. Vicentini, V.: Stress-Concentration Factors for Superposed Notches, Exp. Mech., vol. 7, no. 3, March 1967. 44. Sandor, B. I.: ‘‘Fundamentals of Cyclic Stress and Strain,’’ The University of Wisconsin Press, 1972.
SEC.
3.14]
The Behavior of Bodies under Stress
61
45. Fuchs, H. O., and R. I. Stephens: ‘‘Metal Fatigue in Engineering,’’ John Wiley & Sons, 1980. 46. ‘‘Fatigue and Microstructure,’’ papers presented at the 1978 ASM Materials Science Seminar, American Society for Metals, 1979. 47. Pook, L. P.: ‘‘The Role of Crack Growth in Metal Fatigue,’’ The Metals Society, London, 1983. 48. Ritchie, R. O., and J. Larkford (eds.): ‘‘Small Fatigue Cracks,’’ Proceedings of the Second Engineering Foundation International Conference=Workshop, Santa Barbara, Calif., Jan. 5–10, 1986, The Metallurgical Society, Inc., 1986. 49. ‘‘Int. J. Fracture,’’ Martinus Nijhoff. 50. Eng. Fracture Mech., Pergamon Journals. 51. Journal of Reinforced Plastics and Composites, Technomic Publishing. 52. Liebowitz, H. (ed.): ‘‘Fracture,’’ Academic Press, 1968. 53. Sih. G. C.: ‘‘Handbook of Stress Intensity Factors,’’ Institute of Fracture and Solid Mechanics, Lehigh University, 1973. 54. Kobayashi, A. S. (ed.): ‘‘Experimental Techniques in Fracture Mechanics, 1 and 2,’’ Iowa State University Press, 1973 and 1975. 55. Broek, D.: ‘‘Elementary Engineering Fracture Mechanics,’’ 3d ed., Martinus Nijhoff, 1982. 56. Atluri, S. N. (ed): ‘‘Computational Methods in the Mechanics of Fracture,’’ NorthHolland, 1984. 57. Sih. G. C., E. Sommer, and W. Dahl (eds.): ‘‘Application of Fracture Mechanics to Materials and Structures,’’ Martinus Nijhoff, 1984. 58. Kobayashi, A. S. (ed.): ‘‘Handbook on Experimental Mechanics,’’ Prentice-Hall, 1987. 59. Budynas, R. G.: ‘‘Advanced Strength and Applied Stress Analysis,’’ 2nd ed., McGrawHill, 1999. 60. Schwartz, M. M.: ‘‘Composite Materials Handbook,’’ 2nd ed., McGraw-Hill, 1992.
Chapter
4 Principles and Analytical Methods
Most of the formulas of mechanics of materials express the relations among the form and dimensions of a member, the loads applied thereto, and the resulting stress or deformation. Any such formula is valid only within certain limitations and is applicable only to certain problems. An understanding of these limitations and of the way in which formulas may be combined and extended for the solution of problems to which they do not immediately apply requires a knowledge of certain principles and methods that are stated briefly in the following articles. The significance and use of these principles and methods are illustrated in Part 3 by examples that accompany the discussion of specific problems.
4.1
Equations of Motion and of Equilibrium
The relations that exist at any instant between the motion of a body and the forces acting on it may be expressed by these two equations: (1) Fx (the component along any line x of all forces acting on a body) ¼ ma x (the product of the mass of the body and the x component of the acceleration of its mass center); (2) Tx (the torque about any line x of all forces acting on the body) ¼ dHx =dt (the time rate at which its angular momentum about that line is changing). If the body in question is in equilibrium, these equations reduce to (1) Fx ¼ 0 and (2) Tx ¼ 0. These equations, Hooke’s law, and experimentally determined values of the elastic constants E, G, and n constitute the basis for the mathematical analysis of most problems of mechanics of materials. The majority of the common formulas for stress are derived by considering a portion of the loaded member as a body in equilibrium under the action of forces that include the stresses sought and then solving for these stresses by applying the equations of equilibrium. 63
64
Formulas for Stress and Strain
4.2
Principle of Superposition
[CHAP. 4
With certain exceptions, the effect (stress, strain, or deflection) produced on an elastic system by any final state of loading is the same whether the forces that constitute that loading are applied simultaneously or in any given sequence and is the result of the effects that the several forces would produce if each acted singly. An exception to this principle is afforded by any case in which some of the forces cause a deformation that enables other forces to produce an effect they would not have otherwise. A beam subjected to transverse and axial loading is an example; the transverse loads cause a deflection that enables the longitudinal load to produce a bending effect it would not produce if acting alone. In no case does the principle apply if the deformations are so large as to alter appreciably the geometrical relations of the parts of the system. The principle of superposition is important and has many applications. It often makes it possible to resolve or break down a complex problem into a number of simple ones, each of which can be solved separately for like stresses, deformations, etc., which are then algebraically added to yield the solution of the original problem. 4.3
Principle of Reciprocal Deflections
Let A and B be any two points of an elastic system. Let the displacement of B in any direction U due to force P acting in any direction V at A be u; and let the displacement of A in the direction V due to a force Q acting in the direction U at B be v. Then Pv ¼ Qu. This is the general statement of the principle of reciprocal deflections. If P and Q are equal and parallel and u and v are parallel, the statement can be simplified greatly. Thus, for a horizontal beam with vertical loading and deflection understood, the principle expresses the following relation: A load applied at any point A produces the same deflection at any other point B as it would produce at A if applied at B. The principle of reciprocal deflections is a corollary of the principle of superposition and so can be applied only to cases for which that principle is valid. It can be used to advantage in many problems involving deformation. Examples of the application of the principle are given in Chaps. 8 and 11. 4.4
Method of Consistent Deformations (Strain Compatibility)
Many statically indeterminate problems are easily solved by utilizing the obvious relations among the deformations of the several parts or among the deformations produced by the several loads. Thus the
SEC.
4.5]
Principles and Analytical Methods
65
division of load between the parts of a composite member is readily ascertained by expressing the deformation or deflection of each part in terms of the load it carries and then equating these deformations or deflections. For example, the reaction at the supported end of a beam with one end fixed and the other supported can be found by regarding the beam as a cantilever, acted on by the actual loads and an upward end load (the reaction), and setting the resultant deflection at the support end equal to zero. The method of consistent deformations is based on the principle of superposition; it can be applied only to cases for which that principle is valid. 4.5
Principles and Methods Involving Strain Energy
Strain energy is defined as the mechanical energy stored up in an elastically stressed system; formulas for the amount of strain energy developed in members under various conditions of loading are given in Part 3. It is the purpose of this article to state certain relations between strain energy and external forces that are useful in the analysis of stress and deformation. For convenience, external forces with points of application that do not move will here be called reactions, and external forces with points of application that move will be called loads. When an elastic system is subjected to static loading, the external work done by the loads as they increase from zero to their maximum value is equal to the strain energy acquired by the system. This relation may be used directly to determine the deflection of a system under a single load; for such a case, assuming a linear material, it shows that the deflection at the point of loading in the direction of the load is equal to twice the strain energy divided by the load. The relationship also furnishes a means of determining the critical load that produces elastic instability in a member. A reasonable form of curvature, compatible with the boundary conditions, is assumed, and the corresponding critical load found by equating the work of the load to the strain energy developed, both quantities being calculated for the curvature assumed. For each such assumed curvature, a corresponding approximate critical load will be found and the least load so found represents the closest approximation to the true critical load (see Refs. 3 to 5).
External work equal to strain energy.
During the static loading of an elastic system the external work done by a constant force acting thereon is equal to the
Method of unit loads.
66
Formulas for Stress and Strain
[CHAP. 4
internal work done by the stresses caused by that constant force. This relationship is the basis of the following method for finding the deflection of any given point of an elastic system: A unit force is imagined to act at the point in question and in the direction of the deflection that is to be found. The stresses produced by such a unit force will do a certain amount of internal work during the application of the actual loads. This work, which can be readily found, is equal to the work done by the unit force; but since the unit force is constant, this work is equal to the deflection sought. If the direction of the deflection cannot be ascertained in advance, its horizontal and vertical components can be determined separately in the way described and the resultant deflection found therefrom. Examples of application of the method are given in Sec. 7.4.
When a linear elastic system is statically loaded, the partial derivative of the strain energy with respect to any one of the applied forces is equal to the movement of the point of application of that force in the direction of that force. This relationship provides a means of finding the deflection of a beam or truss under several loads (see Refs. 3, 5, and 7).
Deflection, the partial derivative of strain energy.
Theorem of least work.y When an elastic system is statically loaded,
the distribution of stress is such as to make the strain energy a minimum consistent with equilibrium and the imposed boundary conditions. This principle is used extensively in the solution of statically indeterminate problems. In the simpler type of problem (beams with redundant supports or trusses with redundant members) the first step in the solution consists in arbitrarily selecting certain reactions or members to be considered redundant, the number and identity of these being such that the remaining system is just determinate. The strain energy of the entire system is then expressed in terms of the unknown redundant reactions or stresses. The partial derivative of the strain energy with respect to each of the redundant reactions or stresses is then set equal to zero and the resulting equations solved for the redundant reactions or stresses. The remaining reactions or stresses are then found by the equations of equilibrium. An example of the application of this method is given in Sec. 7.4. y By theorem of least work is usually meant only so much of the theorem as is embodied in the first application here described, and so understood it is often referred to as Castigliano’s second theorem. But, as originally stated by Castigliano, it had a somewhat different significance. (See his ‘‘The´ ore`me de l’e´ quilibre des syste`mes e´ lastiques et ses applications,’’ Paris, 1879, or the English translation ‘‘Elastic Stresses in Structures,’’ by E. S. Andrews, Scott, Greenwood, London. See also R. V. Southwell, Castigliano’s Principle of Minimum Strain-energy, Proc. Roy. Soc. Lond., Ser. A, vol. 154, 1936.) The more general theory stated is called theorem of minimum energy by Love (Ref. 1) and theorem of minimum resilience by Morley (Ref. 2).
SEC.
4.6]
Principles and Analytical Methods
67
As defined by this procedure, the theorem of least work is implicit in Castigliano’s theorem: It furnishes a method of solution identical with the method of consistent deflections, the deflection used being zero and expressed as a partial derivative of the strain energy. In a more general type of problem, it is necessary to determine which of an infinite number of possible stress distributions or configurations satisfies the condition of minimum strain energy. Since the development of software based on the finite-element method of analysis the electronic computer has made practicable the solution of many problems of this kind—shell analysis, elastic and plastic buckling, etc.—that formerly were relatively intractable. 4.6
Dimensional Analysis
Most physical quantities can be expressed in terms of mass, length, and time conveniently represented by the symbols M , L, and t, respectively. Thus velocity is Lt1 acceleration is Lt2 , force is MLt2 , unit stress is ML1 t2 , etc. A formula in which the several quantities are thus expressed is a dimensional formula, and the various applications of this system of representation constitute dimensional analysis. Dimensional analysis may be used to check formulas for homogeneity, check or change units, derive formulas, and establish the relationships between similar physical systems that differ in scale (e.g., a model and its prototype). In strength of materials, dimensional analysis is especially useful in checking formulas for homogeneity. To do this, it is not always necessary to express all quantities dimensionally since it may be possible to cancel some terms. Thus it is often convenient to express force by some symbol, as F, until it is ascertained whether or not all terms representing force can be canceled. For example, consider the formula for the deflection y at the free end of a cantilever beam of length l carrying a uniform load per unit length, w. This formula (Table 8.1) is y¼
1 wl4 8 EI
To test for homogeneity, omit the negative sign and the coefficient (which is dimensionless) and write the formula L¼
1 8
ðF=LÞ4 ðF=L2 ÞL4
It is seen that F cancels and the equation reduces at once to L ¼ L, showing that the original equation was homogeneous.
68
Formulas for Stress and Strain
[CHAP. 4
Instead of the symbols M , L, t, and F, we can use the names of the units in which the quantities are to be expressed. Thus the above equation may be written inches ¼
ðpounds=inchÞðinches4 Þ ðpounds=inches2 Þðinches4 Þ
¼ inches
This practice is especially convenient if it is desired to change units. Thus it might be desired to write the above formula so that y is given in inches when l is expressed in feet. It is only necessary to write inches ¼
1 ðpounds=inchÞðfeet 12Þ4 8 ðpounds=inches2 Þinches4
and the coefficient is thus found to be 2592 instead of 18. By what amounts to a reversal of the checking process described, it is often possible to determine the way in which a certain term or terms should appear in a formula provided the other terms involved are known. For example, consider the formula for the critical load of the Euler column. Familiarity with the theory of flexure suggests that this load will be directly proportional to E and I. It is evident that the length l will be involved in some way as yet unknown. It is also reasonable to assume that the load is independent of the deflection since both the bending moment and the resisting moment would be expected to vary in direct proportion to the deflection. We can then write P ¼ kEIla , where k is a dimensionless constant that must be found in some other way and the exponent a shows how l enters the expression. Writing the equation dimensionally and omitting k, we have F¼
F 4 a L L L2
or
L2 ¼ L4þa
Equating the exponents of L (as required for homogeneity) we find a ¼ 2, showing that the original formula should be P ¼ kEI=l2 . Note that the derivation of a formula in this way requires at least a partial knowledge of the relationship that is to be expressed. A much more detailed discussion of similitude, modeling, and dimensional analysis can be found in Chaps. 15 and 8 of Refs. 6 and 7, respectively. Reference 6 includes a section where the effect of Poisson’s ratio on the stresses in two- and three-dimensional problems is discussed. Since Poisson’s ratio is dimensionless, it would have to be the same in model and prototype for perfect modeling and this generally is not possible. References to work on this problem are included and will be helpful.
SEC.
4.7
4.7]
Principles and Analytical Methods
69
Remarks on the Use of Formulas
No calculated value of stress, strength, or deformation can be regarded as exact. The formulas used are based on certain assumptions as to properties of materials, regularity of form, and boundary conditions that are only approximately true, and they are derived by mathematical procedures that often involve further approximations. In general, therefore, great precision in numerical work is not justified. Each individual problem requires the exercise of judgment, and it is impossible to lay down rigid rules of procedure; but the following suggestions concerning the use of formulas may be of value. 1. For most cases, calculations giving results to three significant figures are sufficiently precise. An exception is afforded by any calculation that involves the algebraic addition of quantities that are large in comparison with the final result (e.g., some of the formulas for beams under axial and transverse loading, some of the formulas for circular rings, and any case of superposition in which the effects of several loads tend to counteract each other). For such cases more significant figures should be carried throughout the calculations. 2. In view of uncertainties as to actual conditions, many of the formulas may appear to be unnecessarily elaborate and include constants given to more significant figures than is warranted. For this reason, we may often be inclined to simplify a formula by dropping unimportant terms, ‘‘rounding off ’’ constants, etc. It is sometimes advantageous to do this, but it is usually better to use the formula as it stands, bearing in mind that the result is at best only a close approximation. The only disadvantage of using an allegedly ‘‘precise’’ formula is the possibility of being misled into thinking that the result it yields corresponds exactly to a real condition. So far as the time required for calculation is concerned, little is saved by simplification. 3. When using an unfamiliar formula, we may be uncertain as to the correctness of the numerical substitutions made and mistrustful of the result. It is nearly always possible to effect some sort of check by analogy, superposition, reciprocal deflections, comparison, or merely by judgment and common sense. Thus the membrane analogy (Sec. 5.4) shows that the torsional stiffness of any irregular section is greater than that of the largest inscribed circular section and less than that of the smallest circumscribed section. Superposition shows that the deflection and bending moment at the center of a beam under triangular loading (Table 8.1, case 2e) is the same as under an equal load uniformly distributed. The principle of reciprocal deflections shows that the stress and deflection at the center of a circular flat plate under eccentric concentrated load (Table 11.2, case 18) are the same as for an equal load uniformly distributed along a concentric circle with radius equal to the eccentricity (case 9a). Comparison
70
Formulas for Stress and Strain
[CHAP. 4
shows that the critical unit compressive stress is greater for a thin plate under edge loading than for a strip of that plate regarded as an Euler column. Common sense and judgment should generally serve to prevent the acceptance of grossly erroneous calculations. 4. A difficulty frequently encountered is uncertainty as to boundary conditions—whether a beam or flat plate should be calculated as freely supported or fixed, whether a load should be assumed uniformly or otherwise distributed, etc. In any such case it is a good plan to make bracketing assumptions, i.e., to calculate the desired quantity on the basis of each of two assumptions representing limits between which the actual conditions must lie. Thus for a beam with ends having an unknown degree of fixity, the bending moment at the center cannot be more than if the ends were freely supported and the bending moments at the ends cannot be more than if the ends were truly fixed. If so designed as to be safe for either extreme condition, the beam will be safe for any intermediate degree of fixity. 5. The stress and deflections predicted by most formulas do not account for localized effects of the loads. For example, the stresses and deflections given for a straight, simply-supported beam with a centered, concentrated lateral force only account for that due to bending. Additional compressive bearing stresses and deflections exist depending on the exact nature of the interaction of the applied and reaction forces with the beam. Normally, the state of stress and deformation at distances greater than the dimensions of the loaded regions only depend on the net effect of the localized applied and reaction forces and are independent of the form of these forces. This is an application of Saint Venant’s principle (defined in Appendix B). This principle may not be reliable for thin-walled structures or for some orthotropic materials. 6. Formulas concerning the validity of which there is a reason for doubt, especially empirical formulas, should be checked dimensionally. If such a formula expresses the results of some intermediate condition, it should be checked for extreme or terminal conditions; thus an expression for the deflection of a beam carrying a uniform load over a portion of its length should agree with the corresponding expression for a fully loaded beam when the loaded portion becomes equal to the full length and should vanish when the loaded portion becomes zero.
4.8
References
1. Love, A. E. H.: ‘‘Mathematical Theory of Elasticity,’’ 2nd ed., Cambridge University Press, 1906. 2. Morley, A.: ‘‘Theory of Structures,’’ 5th ed., Longmans, Green, 1948. 3. Langhaar, H. L.: ‘‘Energy Methods in Applied Mechanics,’’ John Wiley & Sons, 1962. 4. Timoshenko, S., and J. M. Gere: ‘‘Theory of Elastic Stability,’’ 2nd ed., McGraw-Hill, 1961.
SEC.
4.8]
Principles and Analytical Methods
71
5. Cook, R. D., and W. C. Young: ‘‘Advanced Mechanics of Materials,’’ 2nd ed., PrenticeHall, 1999. 6. Kobayashi, A. S. (ed.): ‘‘Handbook on Experimental Mechanics,’’ 2nd ed., Society for Experimental Mechanics, VCH, 1993. 7. Budynas, R. G. ‘‘Advanced Strength and Applied Stress Analysis,’’ 2nd ed., McGrawHill, 1999.
Chapter
5 Numerical Methods
The analysis of stress and deformation of the loading of simple geometric structures can usually be accomplished by closed-form techniques. As the structures become more complex, the analyst is forced to approximations of closed-form solutions, experimentation, or numerical methods. There are a great many numerical techniques used in engineering applications for which digital computers are very useful. In the field of structural analysis, the numerical techniques generally employ a method which discretizes the continuum of the structural system into a finite collection of points (or nodes) whereby mathematical relations from elasticity are formed. The most popular technique used currently is the finite element method (FEM). For this reason, most of this chapter is dedicated to a general description of the method. A great abundance of papers and textbooks have been presented on the finite element method, and a complete listing is beyond the scope of this book. However, some textbooks and historical papers are included for introductory purposes. Other methods, some of which FEM is based upon, include trial functions via variational methods and weighted residuals, the finite difference method (FDM), structural analogues, and the boundary element method (BEM). FDM and BEM will be discussed briefly.
5.1
The Finite Difference Method
In the field of structural analysis, one of the earliest procedures for the numerical solutions of the governing differential equations of stressed continuous solid bodies was the finite difference method. In the finite difference approximation of differential equations, the derivatives in the equations are replaced by difference quotients of the values of the dependent variables at discrete mesh points of the domain. After imposing the appropriate boundary conditions on the structure, the 73
74
Formulas for Stress and Strain
[CHAP. 5
discrete equations are solved obtaining the values of the variables at the mesh points. The technique has many disadvantages, including inaccuracies of the derivatives of the approximated solution, difficulties in imposing boundary conditions along curved boundaries, difficulties in accurately representing complex geometric domains, and the inability to utilize non-uniform and non-rectangular meshes. 5.2
The Finite Element Method
The finite element method (FEM) evolved from the use of trial functions via variational methods and weighted residuals, the finite difference method, and structural analogues (see Table 1.1 of Ref. 1). FEM overcomes the difficulties encountered by the finite-difference method in that the solution of the differential equations of the structural problem are obtained by utilizing an integral formulation to generate a system of algebraic equations with continuous piecewisesmooth (trial) functions that approximate the unknown quantities. A geometrically complex domain of the structural problem can be systematically represented by a large, but finite, collection of simpler subdomains, called finite elements. For structural problems, the displacement field of each element is approximated by polynomials, which are interpolated with respect to preselected points (nodes) on, and possibly within, the element. The polynomials are referred to as interpolation functions, where variational or weighted residual methods (e.g. Rayleigh–Ritz, Galerkin, etc.) are applied to determine the unknown nodal values. Boundary conditions can easily be applied along curved boundaries, complex geometric domains can be modeled, and non-uniform and non-rectangular meshes can be employed. The modern development of FEM began in the 1940s in the field of structural mechanics with the work of Hrennikoff, McHenry, and Newmark, who used a lattice of line elements (rods and beams) for the solution of stresses in continuous solids (see Refs. 2–4). In 1943, from a 1941 lecture, Courant suggested piecewise-polynomial interpolation over triangular subregions as a method to model torsional problems (see Ref. 5). With the advent of digital computers in the 1950s, it became practical for engineers to write and solve the stiffness equations in matrix form (see Refs. 6–8). A classic paper by Turner, Clough, Martin, and Topp published in 1956 presented the matrix stiffness equations for the truss, beam, and other elements (see Ref. 9). The expression finite element is first attributed to Clough (see Ref. 10). Since these early beginnings, a great deal of effort has been expended in the development of FEM in the areas of element formulations and computer implementation of the entire solution process. The major advances in computer technology includes the rapidly expand-
SEC.
5.2]
Numerical Methods
75
ing computer hardware capabilities, efficient and accurate matrix solver routines, and computer graphics for ease in the preprocessing stages of model building, including automatic adaptive mesh generation, and in the postprocessing stages of reviewing the solution results. A great abundance of literature has been presented on the subject, including many textbooks. A partial list of some textbooks, introductory and more comprehensive, is given at the end of this chapter. For a brief introduction to FEM and modeling techniques, see Chapters 9 and 10, respectively, of Ref. 11. FEM is ideally suited to digital computers, in which a continuous elastic structure (continuum) is divided (discretized) into small but finite well-defined substructures (elements). Using matrices, the continuous elastic behavior of each element is categorized in terms of the element’s material and geometric properties, the distribution of loading (static, dynamic, and thermal) within the element, and the loads and displacements at the nodes of the element. The element’s nodes are the fundamental governing entities of the element, since it is the node where the element connects to other elements, where elastic properties of the element are established, where boundary conditions are assigned, and where forces (contact or body) are ultimately applied. A node possesses degrees of freedom (dof ’s). Degrees of freedom are the translational and rotational motion that can exist at a node. At most, a node can possess three translational and three rotational degrees of freedom. Once each element within a structure is defined locally in matrix form, the elements are then globally assembled (attached) through their common nodes (dof ’s) into an overall system matrix. Applied loads and boundary conditions are then specified, and through matrix operations the values of all unknown displacement degrees of freedom are determined. Once this is done, it is a simple matter to use these displacements to determine strains and stresses through the constitutive equations of elasticity. Many geometric shapes of elements are used in finite element analysis for specific applications. The various elements used in a general-purpose commercial FEM software code constitute what is referred to as the element library of the code. Elements can be placed in the following categories: line elements, surface elements, solid elements, and special purpose elements. Table 5.1 provides some, but not all, of the types of elements available for finite element analysis. Since FEM is a numerical technique that discretizes the domain of a continuous structure, errors are inevitable. These errors are: 1. Computational errors. These are due to round-off errors from the computer floating-point calculations and the formulations of the numerical integration schemes that are employed. Most commercial
76
Formulas for Stress and Strain
TABLE 5.1
Sample finite element library
Element type
Name
Line
Shape
[CHAP. 5
Number of nodes
Applications
Truss
2
Beam
2
Frame
2
Axial, torsional, and bending. With or without load stiffening
Surface 4 Noded quadrilateral 8 Noded quadrilateral 3 Noded triangular
4
Plane stress or strain, axisymmetry, shear panel, thin flat plate in bending Plane stress or strain, thin plate or shell in bending
6 Noded triangular
6
8 Noded hexagonal (brick)
8
Solid, thick plate (using midside nodes)
6 Noded Pentagonal (wedge)
6
Solid, thick plate (using midside nodes). Used for transitions
4 Noded tetrahedron (tet)
4
Solid, thick plate (using midside nodes). Used for transitions
Solidy
Special Gap purpose Hook Rigid
8
3
Pin-ended bar in tension or compression Bending
Plane stress or strain, axisymmetry, shear panel, thin flat plate in bending. Prefer quad where possible. Used for transitions of quads Plane stress or strain, axisymmetry, thin plate or shell in bending. Prefer quad where possible. Used for transitions of quads
2
Free displacement for prescribed compressive gap 2 Free displacement for prescribed extension gap Variable Rigid constraints between nodes
y These elements are also available with mid-size nodes.
finite element codes concentrate on reducing these errors and consequently the analyst generally is concerned with discretization factors. 2. Discretization errors. The geometry and the displacement distribution of a true structure vary continuously. Using a finite number of elements to model the structure introduces errors in matching geometry and the displacement distribution due to the inherent limita-
SEC.
5.3]
Numerical Methods
77
tions of the elements. For example, consider the thin plate structure shown in Fig. 5.1(a). Figure 5.1(b) shows a finite element model of the structure where three-noded, plane stress, triangular elements are employed. The plane stress triangular element has a flaw, which creates two basic problems. The element has straight sides, which remain straight after deformation. The strains throughout the plane stress triangular element are constant. The first problem, a geometric one, is the modeling of curved edges. Note that the surface of the model with a large curvature appears reasonably modeled, whereas the surface of the hole is very poorly modeled. The second problem, which is much more severe, is that the strains in various regions of the actual structure are changing rapidly, and the constant strain element will only provide an approximation of the average strain at the center of the element. So, in a nutshell, the results predicted using this model will be relatively poor. The results can be improved by significantly increasing the number of elements used (increased mesh density). Alternatively, using a better element, such as an eight-noded quadrilateral, which is more suited to the application, will provide the improved results. Due to higher-order interpolation functions, the eight-noded quadrilateral element can model curved edges and provides for a higher-order function for the strain distribution.
5.3
The Boundary Element Method
The boundary element method (BEM), developed more recently than FEM, transforms the governing differential equations and boundary conditions into integral equations, which are converted to contain
Figure 5.1
Discretization of a continuous structure.
78
Formulas for Stress and Strain
[CHAP. 5
surface integrals (see Refs. 12–16). Because only surface integrals remain, surface elements are used to perform the required integrations. This is the main advantage that BEM has over FEM, which requires three-dimensional elements throughout the entire volumetric domain. Boundary elements for a general three-dimensional solid are quadrilateral or triangular surface elements covering the surface area of the component. For two-dimensional and axisymmetric problems, only line elements tracing the outline of the component are necessary. Although BEM offers some modeling advantages over FEM, the latter can analyze more types of engineering applications and is much more firmly entrenched in today’s computer-aided-design (CAD) environment. Development of engineering applications of BEM are proceeding however, and more will be seen of the method in the future. 5.4
References
1. Zienkiewicz, O. C., and Taylor, R. L.: ‘‘The Finite Element Method, vol. 1, Basic Formulations and Linear Problems,’’ 4th ed., McGraw-Hill, 1989. 2. Hrennikoff, A.: Solution of Problems in Elasticity by the Frame Work Method, J. Appl. Mech., vol. 8, no. 4, pp. 169–175, 1941. 3. McHenry, D.: A Lattice Analogy for the Solution of Plane Stress Problems, J. Inst. Civil Eng., vol. 21, pp. 59–82, 1943. 4. Newmark, N. M.: Numerical Methods of Analysis in Bars, Plates, and Elastic Bodies, ‘‘Numerical Methods in Analysis in Engineering’’ (ed. L. E. Grinter), Macmillan, 1949. 5. Courant, R.: Variational Methods for the Solution of Problems of Equilibrium and Vibrations, Bull. Am. Math. Soc., vol. 49, pp. 1–23, 1943. 6. Levy, S.: Structural Analysis and Influence Coefficients for Delta Wings, J. Aero. Sci., vol. 20, no. 7, pp. 449–454, 1953. 7. Argyris, J. H.: Energy Theorems and Structural Analysis, Aircraft Eng., Oct., Nov., Dec. 1954 and Feb., Mar., Apr., May 1955. 8. Argyris, J. H., and Kelsey, S.: ‘‘Energy Theorems and Structural Analysis,’’ Butterworths, 1960 (reprinted from Aircraft Eng., 1954–55). 9. Turner, M. J., Clough, R. W., Martin, H. C., and Topp, L. J.: Stiffness and Deflection Analysis of Complex Structures, J. Aero. Sci., vol. 23, no. 9, pp. 805–824, 1956. 10. Clough, R. W.: The Finite Element Method in Plane Stress Analysis, ‘‘Proceedings of the Second Conference on Electronic Computation,’’ American Society of Civil Engineers, Pittsburgh, PA, pp. 345–378, September 1960. 11. Budynas, R. G.: ‘‘Advanced Strength and Applied Stress Analysis,’’ 2nd ed., McGrawHill, 1999. 12. Rizzo, F. J.: An Integral Equation Approach to Boundary Value Problems of Classical Elastostatics, Q. Appl. Math., vol. 25, pp. 83–95, 1967. 13. Cruse, T. A.: Numerical Solutions in Three-Dimensional Elastostatics, Int. J. Solids Struct., vol. 5, pp. 1258–1274, 1969. 14. Brebbia, C. A.: ‘‘The Boundary Element Method for Engineers,’’ Pentech Press, 1978. 15. Banerjee, P. K., and Butterfield, R.: ‘‘Boundary Element Methods in Engineering Science,’’ McGraw-Hill, 1981. 16. Trevelyan, J.: ‘‘Boundary Elements for Engineers,’’ Computational Mechanics Publications, 1994.
Additional Uncited References in Finite Elements 17. Bathe, K. J.: ‘‘Finite Element Procedures,’’ Prentice-Hall, 1996.
SEC.
5.4]
Numerical Methods
79
18. Chandrupatla, T. R., and Belegundu, A. D.: ‘‘Introduction to Finite Elements in Engineering,’’ 2nd ed., Prentice-Hall, 1997. 19. Cook, R. D., Malkus, D. S., and Plesha, M. E.: ‘‘Concepts and Applications of Finite Element Analysis,’’ 3rd ed., John Wiley & Sons, 1989. 20. Cook, R. D.: ‘‘Concepts and Applications of Finite Element Analysis,’’ 2nd ed., John Wiley & Sons, 1981. 21. Cook, R. D. ‘‘Finite Element Modeling for Stress Analysis,’’ John Wiley & Sons, 1995. 22. Reddy, J. N.: ‘‘An Introduction to the Finite Element Method,’’ 2nd ed., McGraw-Hill, 1984.
Chapter
6 Experimental Methods
A structural member may be of such a form or may be loaded in such a way that the direct use of formulas for the calculation of stresses and strain produced in it is ineffective. One then must resort either to numerical techniques such as the finite element method or to experimental methods. Experimental methods can be applied to the actual member in some cases, or to a model thereof. Which choice is made depends upon the results desired, the accuracy needed, the practicality of size, and the cost associated with the experimental method. There has been a tremendous increase in the use of numerical methods over the years, but the use of experimental methods is still very effective. Many investigations make use of both numerical and experimental results to cross-feed information from one to the other for increased accuracy and cost effectiveness (see Chap. 17 in Ref. 27). Some of the more important experimental methods are described briefly in Sec. 6.1 of this chapter. Of these methods, the most popular method employs electrical resistance strain gages, and is described in more detail in Sec. 6.2. Only textbooks, reference books, handbooks, and lists of journals are referenced, since there are several organizations (see Refs. 1, 25, and 26) devoted either partially or totally to experimental methods, and a reasonable listing of papers would be excessive and soon out of date. The most useful reference for users wanting information on experimental methods is Ref. 27, the ‘‘Handbook on Experimental Mechanics,’’ edited by A. S. Kobayashi and dedicated to the late Dr. M. Hetenyi, who edited Ref. 2. Reference 27 contains 22 chapters contributed by 27 authors under the sponsorship of the Society for Experimental Mechanics. Experimental methods applied specifically to the field of fracture mechanics are treated extensively in Refs. 13, 15, 17, 19, 22, and Chaps. 14 and 20 of Ref. 27. 81
82
Formulas for Stress and Strain
6.1
Measurement Techniques
[CHAP. 6
The determination of stresses produced under a given loading of a structural system by means of experimental techniques are based on the measurement of deflections. Since strain is directly related to (the rate of change of ) deflection, it is common practice to say that the measurements made are that of strain. Stresses are then determined implicitly using the stress–strain relations. Deflections in a structural system can be measured through changes in resistance, capacitance, or inductance of electrical elements; optical effects of interference, diffraction, or refraction; or thermal emissions. Measurement is comparatively easy when the stress is fairly uniform over a considerable length of the part in question, but becomes more difficult when the stress is localized or varies greatly with position. Short gage lengths and great precision require stable gage elements and stable electronic amplification if used. If dynamic strains are to be measured, a suitable high-frequency response is also necessary. In an isotropic material undergoing uniaxial stress, one normal strain measurement is all that is necessary. On a free surface under biaxial stress conditions, two measured orthogonal normal strains will provide the stresses in the same directions of the measured strains. On a free surface under a general state of plane stress, three measured normal strains in different directions will allow the determination of the stresses in directions at that position (see Sec. 6.2). At a free edge in a member that is thin perpendicular to the free edge, the state of stress is uniaxial and, as stated earlier, can be determined from one normal strain tangent to the edge. Another tactic might be to measure the change in thickness or the through-thickness strain at the edge. This might be more practical, such as measuring the strain at the bottom of a groove in a thin plate. For example, assume an orthogonal xyz coordinate system where x is parallel to the edge and z is in the direction of the thickness at the edge. Considering a linear, isotropic material, from Hooke’s law, ez ¼ nsx =E. Thus, sx ¼ Eez =n. The following descriptions provide many of the successful instruments and techniques used for strain measurement. They are listed in a general order of mechanical, electrical, optical, and thermal methods. Optical and thermal techniques have been greatly enhanced by advances in digital image processing technology for computers (see Chap. 21 of Ref. 27). A direct measurement of strain can be made with an Invar tape over a gage length of several meters or with a pair of dividers over a reasonable fraction of a meter. For shorter gage lengths, mechanical amplification can be used, but friction is a problem and vibration can make them difficult to mount and to
1. Mechanical measurement.
SEC.
6.1]
Experimental Methods
83
read. Optical magnification using mirrors still requires mechanical levers or rollers and is an improvement but still not satisfactory for most applications. In a laboratory setting, however, such mechanical and optical magnification can be used successfully. See Ref. 3 for more detailed descriptions. A scratch gage uses scratches on a polished target to determine strain amplitudes, and while the scratches are in general not strictly related to time, they are usually related to events in such a way as to be extremely useful in measuring some dynamic events. The scratched target is viewed with a microscope to obtain peak-to-peak strains per event, and a zero strain line can also be scratched on the target if desired (Ref. 3). The use of lasers and=or optical telescopes with electronic detectors to evaluate the motion of fiduciary marks on distant structures makes remote-displacement measurements possible, and when two such detectors are used, strains can be measured. While the technique is valuable when needed for remote measurement, generally for environmental reasons, it is an expensive technique for obtaining the strain at a single location. Surface coatings formulated to crack at strain levels well within the elastic limit of most structural materials provide a means of locating points of maximum strain and the directions of principal strains. Under well-controlled environmental conditions and with suitable calibration, such coatings can yield quantitative results (Refs. 2, 3, 7, 9, 20, 21, and 27). This technique, however, is not universally applicable, since the coatings may not be readily available due to environmental problems with the coating materials.
2. Brittle coatings.
The evolution of electrical gages has led to a variety of configurations where changes in resistance, capacitance, or inductance can be related to strain and displacement with proper instrumentation (Refs. 2–5, 20, 21, 23, 24, and 27).
3. Electrical strain and displacement gages.
(a) Resistance strain gage. For the electrical resistance strain gages, the gage lengths vary from less than 0.01 in to several inches. The gage grid material can be metallic or a semiconductor. The gages can be obtained in alloys that are designed to provide minimum output due to temperature strains alone and comparatively large outputs due to stress-induced strains. Metallic bonded-foil gages are manufactured by a photoetching process that allows for a wide range of configurations of the grid(s). The semiconductor strain gages provide the largest resistance change for a given strain, but are generally very sensitive to temperature changes. They are used in transducers where proper design can provide temperature compensation The use of electrical resistance strain gages for stress analysis purposes constitute the
84
Formulas for Stress and Strain
[CHAP. 6
majority of experimental applications. For this reason, Sec. 6.2 provides further information on the use of these gages. (b) Capacitance strain gage. Capacitance strain gages are larger and more massive than bonded electric resistance strain gages and are more widely used for applications beyond the upper temperature limits of the bonded resistance strain gages. (c) Inductance strain gages. The change in air gap in a magnetic circuit can create a large change in inductance depending upon the design of the rest of the magnetic circuit. The large change in inductance is accompanied by a large change in force across the gap, and so the very sensitive inductance strain gages can be used only on more massive structures. They have been used as overload indicators on presses with no electronic amplification necessary. The linear relationship between core motion and output voltage of a linear differential transformer makes possible accurate measurement of displacements over a wide range of gage lengths and under a wide variety of conditions. The use of displacement data as input for work in experimental modal analysis is discussed in Chap. 16 of Ref. 27 and in many of the technical papers in Ref. 24. Whole-field interferometric techniques will be discussed later, but a simple strain gage with a short length and high sensitivity can be created by several methods. In one, a diffraction grating is deposited at the desired location and in the desired direction and the change in grating pitch under strain is measured. With a metallic grid, these strain gages can be used at elevated temperatures. Another method, also useable at high temperatures, makes use of the interference of light reflected from the inclined surfaces of two very closely spaced indentations in the surface of a metallic specimen. Both of these methods are discussed and referenced in Ref. 27.
4. lnterferometrlc strain gages.
5. Photoelastic analysis. When a beam of polarized light passes
through an elastically stressed transparent isotropic material, the beam may be treated as having been decomposed into two rays polarized in the planes of the principal stresses in the material. In birefringent materials the indexes of refraction of the material encountered by these two rays will depend upon the principal stresses. Therefore, interference patterns will develop which are proportional to the differences in the principal stresses. (a) Two-dimensional analysis. With suitable optical elements— polarizers and wave plates of specific relative retardation—both the principal stress differences and the directions of principal stresses
SEC.
6.1]
Experimental Methods
85
may be determined at every point in a two-dimensional specimen (Refs. 2–6, 10, 14, 18, 27, and 28). Many suitable photoelastic plastics are available. The material properties that must be considered are transparency, sensitivity (relative index of refraction change with stress), optical and mechanical creep, modulus of elasticity, ease of machining, cost, and stability (freedom from stresses developing with time). Materials with appropriate creep properties may be used for photoplasticity studies (Ref. 16). (b) Three-dimensional analysis. Several photoelastic techniques are used to determine stresses in three-dimensional specimens. If information is desired at a single point only, the optical polarizers, wave plates, and photoelastically sensitive material can be embedded in a transparent model (Ref. 2) and two-dimensional techniques used. A modification of this technique, stress freezing, is possible in some biphase materials. By heating, loading, cooling, and unloading, it is possible to lock permanently into the specimen, on a molecular level, strains proportional to those present under load. Since equilibrium exists at a molecular level, the specimen can be cut into twodimensional slices and all secondary principal stress differences determined. The secondary principal stresses at a point are defined as the largest and smallest normal stresses in the plane of the slice; these in general will not correspond with the principal stresses at that same point in the three-dimensional structure. If desired, the specimen can be cut into cubes and the three principal stress differences determined. The individual principal stresses at a given point cannot be determined from photoelastic data taken at that point alone since the addition of a hydrostatic stress to any cube of material would not be revealed by differences in the indexes of refraction. Mathematical integration techniques, which start at a point where the hydrostatic stress component is known, can be used with photoelastic data to determine all individual principal stresses. A third method, scattered light photoelasticity, uses a laser beam of intense monochromatic polarized light or a similar thin sheet of light passing through photoelastically sensitive transparent models that have the additional property of being able to scatter uniformly a small portion of the light from any point on the beam or sheet. The same general restrictions apply to this analysis as applied to the stress-frozen three-dimensional analysis except that the specimen does not have to be cut. However, the amount of light available for analysis is much less, the specimen must be immersed in a fluid with an index of refraction that very closely matches that of the specimen, and in general the data are much more difficult to analyze. (c) Photoelastic coating. Photoelastic coatings have been sprayed, bonded in the form of thin sheets, or cast directly in place on the
86
Formulas for Stress and Strain
[CHAP. 6
surface of models or structures to determine the two-dimensional surface strains. The surface is made reflective before bonding the plastics in place so the effective thickness of the photoelastic plastic is doubled and all two-dimensional techniques can be applied with suitable instrumentation. 6. Moire´ techniques. All moire´ techniques can be explained by optical interference, but the course-grid techniques can also be evaluated on the basis of obstructive or mechanical interference.
(a) Geometric moire´. Geometric moire´ techniques use grids of alternate equally wide bands of relatively transparent or light-colored material and opaque or dark-colored material in order to observe the relative motion of two such grids. The most common technique (Refs. 2, 5, 8, and 11) uses an alternate transparent and opaque grid to produce photographically a matching grid on the flat surface of the specimen. Then the full-field relative motion is observed between the reproduction and the original when the specimen is loaded. Similarly, the original may be used with a projector to produce the photographic image on the specimen and then produce interference with the projected image after loading. These methods can use ordinary white light, and the interference is due merely to geometric blocking of the light as it passes through or is reflected from the grids. Another similar technique, shadow moire´, produces interference patterns due to motion of the specimen at right angles to its surface between an alternately transparent and opaque grid and the shadow of the grid on the specimen. (b) Moire´ interferometry. Interferometry provides a means of producing both specimen gratings and reference gratings. Virtual reference gratings of more than 100,000 lines per inch have been utilized. Moire´ interferometry provides contour maps of in-plane displacements, and, with the fine pitches attainable, differentiation to obtain strains from this experimental process is comparable to that used in the finite-element method of numerical analysis where displacement fields are generally the initial output. See Chap. 7 in Ref. 27. The rapid evolution of holographic and laser speckle interferometry is related to the development of high-power lasers and to the development of digital computer enhancement of the resulting images. Various techniques are used to measure the several displacement components of diffuse reflecting surfaces. Details are beyond the scope of this book and are best reviewed in Chap. 8 of Ref. 27.
7. Holographic and laser speckle interferometry.
SEC.
6.2]
Experimental Methods
87
The very simple images created by the reflection or refraction of light from the surface contours of high-gradient stress concentrations such as those at the tips of cracks make the use of the shadow optical method of caustics very useful for dynamic studies of crack growth or arrest. Chapter 9 of Ref. 27 gives a detailed discussion of this technique and a comparison to photoelastic studies for the same loadings.
8. Shadow optical method of caustics.
9. X-ray diffraction. X-ray diffraction makes possible the determination
of changes in interatomic distance and thus the measurement of elastic strain. The method has the particular advantages that it can be used at points of high stress concentration and to determine residual stresses without cutting the object of investigation. 10. Stress-pattern analysis by thermal emission. This technique uses
computer enhancement of infrared detection of very small temperature changes in order to produce digital output related to stress at a point on the surface of a structure, a stress graph along a line on the surface, or a full-field isopachic stress map of the surface. Under cyclic loading, at a frequency high enough to assure that any heat transfer due to stress gradients is insignificant, the thermoelastic effect produces a temperature change proportional to the change in the sum of the principal stresses. Although calibration corrections must be made for use at widely differing ambient temperatures, the technique works over a wide range of temperatures and on a variety of structural materials including metals, wood, concrete, and plain and reinforced plastics. Tests have been made on some metals at temperatures above 700 C. Chapter 14 of Ref. 27 describes and surveys work on this technique. 6.2
Electrical Resistance Strain Gages
General. The use of electrical resistance strain gages is probably the most common method of measurement in experimental stress analysis. In addition, strain gage technology is quite important in the design of transducer instrumentation for the measurement of force, torque, pressure, etc. Electrical resistance strain gages are based on the principal that the resistance R of a conductor changes as a function of normal strain e. The resistance of a conductor can be expressed as
R¼r
L A
(6.2-1)
where r is the resistivity of the conductor (ohms-length), and L and A are the length and cross-sectional area of the conductor respectively. It
88
Formulas for Stress and Strain
[CHAP. 6
can be shown that a change in R due to changes in r, L and A is given by DR Dr ¼ ð1 þ 2nÞe þ R r
(6.2-2)
where n is Poisson’s ratio, and assuming small strain on the conductor, e, which is given by DL=L. If the change in the resistance of the conductor is considered to be only due to the applied strain, then Eq. (6.2-2) can be written as DR ¼ Sa e R
(6.2-3)
where Sa ¼ 1 þ 2n þ
Dr=r e
(6.2-4)
Sa is the sensitivity of the conductor to strainy . The first two terms come directly from changes in dimension of the conductor where for most metals the quantity 1 þ 2n varies from 1.4 to 1.7. The last term in Eq. (6.2-4) is called the change in specific resistance relative to strain, and for some metals can account for much of the sensitivity to strain. The most commonly used material for strain gages is a copper–nickel alloy called Constantan, which has a strain sensitivity of 2.1. Other alloys used for strain gage applications are modified Karma, Nichrome V, and Isoelastic, which have sensitivities of 2.0, 2.2, and 3.6, respectively. The primary advantages of Constantan are: 1. The strain sensitivity Sa is linear over a wide range of strain and does not change significantly as the material goes plastic. 2. The thermal stability of the material is excellent and is not greatly influenced by temperature changes when used on common structural materials. 3. The metallurgical properties of Constantan are such that they can be processed to minimize the error induced due to the mismatch in the thermal expansion coefficients of the gage and the structure to which it is adhered over a wide range of temperature.
y When using a commercial strain indicator, one must enter the sensitivity provided by the gage manufacturer. This sensitivity is referred to the gage factor of the gage, Sg . This is defined slightly differently than Sa , and will be discussed shortly.
SEC.
6.2]
Experimental Methods
89
Isoelastic, with a higher sensitivity, is used for dynamic applications. Semiconductor gages are also available, and can reach sensitivities as high as 175. However, care must be exercised with respect to the poor thermal stability of these piezoresistive gages. Most gages have a nominal resistance of 120 ohm or 350 ohm. Considering a 120-ohm Constantan gage, to obtain a measurement of strain within an accuracy of 5 m, it would be necessary to measure a change in resistance within 1:2 mohm. To measure these small changes in resistance accurately, commercial versions of the Wheatstone bridge, called strain gage indicators, are available. Metallic alloy electrical resistance strain gages used in experimental stress analysis come in two basic types: bonded-wire and bonded-foil (see Fig. 6.1). Today, bonded-foil gages are by far the more prevalent. The resistivity of Constantan is approximately 49 mohm cm. Thus if a strain gage is to be fabricated using a wire 0.025 mm in diameter and is to have a resistance of 120 ohm, the gage would require a wire approximately 120 mm long. To make the gage more compact over a shorter active length, the gage is constructed with many loops as shown in Fig. 6.1. Typical commercially available bonded-foil gage lengths vary from 0.20 mm (0.008 in) to 101.6 mm (4.000 in). For normal applications, bonded-foil gages either come mounted on a very thin polyimide film carrier (backing) or are encapsulated between two thin films of polyimide. Other carrier materials are available for special cases such as high-temperature applications. The most widely used adhesive for bonding a strain gage to a test structure is the pressure-curing methyl 2-cyanoacrylate cement. Other adhesives include epoxy, polyester, and ceramic cements.
Figure 6.1
Forms of electrical resistance strain gages.
90
Formulas for Stress and Strain
[CHAP. 6
Extreme care must be exercised when installing a gage, since a good bond and an electrically insulated gage are necessary. The installation procedures can be obtained from technical instruction bulletins supplied by the manufacturer. Once a gage is correctly mounted, wired, resistance tested for continuity and insulation from the test structure, and waterproofed (if appropriate), it is ready for instrumentation and testing.
In both wire or foil gages, many configurations and sizes are available. Strain gages come in many forms for transducer or stress-analysis applications. The fundamental configurations for stress-analysis work are shown in Fig. 6.2. A strain gage is mounted on a free surface, which in general, is in a state of plane stress where the state of stress with regards to a specific xy rectangular coordinate system can be unknown up to the three stresses, sx , sy , and txy . Thus, if the state of stress is completely unknown on a free surface, it is necessary to use a three-element rectangular or delta rosette since each gage element provides only one piece of information, the indicated normal strain at the point in the direction of the gage. To understand how the rosettes are used, consider the three-element rectangular rosette shown in Fig. 6.3(a), which provides normal strain components in three directions spaced at angles of 45 . If an xy coordinate system is assumed to coincide with gages A and C, then ex ¼ eA and ey ¼ eC . Gage B in conjunction with gages A and C provides information necessary to determine gxy . Recalling the first of Eqs. (2.4-1), ex0 ¼ ex cos2 y þ ey sin2 y þ gxy cos y sin y, with y ¼ 45 Strain Gage Configurations.
eB ¼ ex cos2 45 þ ey sin2 45 þ gxy cos 45 sin 45 ¼ 12 ðex þ ey þ gxy Þ ¼ 12 ðeA þ eC þ gxy Þ Solving for gxy yields gxy ¼ 2eB eA eC Once ex , ey , and gxy are known, Hooke’s law [Eqs. (2.2-5) and (2.2-6a)] can be used to determine the stresses sx , sy , and txy .
SEC.
6.2]
Experimental Methods
91
Figure 6.2 Examples of commonly used strain gage configurations. (Source: Figures a c courtesy of BLH Electronics, Inc., Canton, MA. Figures d f courtesy of MicroMeasurements Division of Measurements Group, Inc., Raleigh, NC.) Note: The letters SR-4 on the BLH gages are in honor of E. E. Simmons and Arthur C. Ruge and their two assistants (a total of four individuals), who, in 1937–1938, independently produced the first bonded-wire resistance strain gage.
The relationship between eA , eB , and eC can be seen from Mohr’s circle of strain corresponding to the strain state at the point under investigation [see Fig. 6.3(b)]. The following example shows how to use the above equations for an analysis as well as how to use the equations provided in Table 6.1.
EXAMPLE A three-element rectangular rosette strain gage is installed on a steel specimen. For a particular state of loading of the structure the strain gage readings arey eA ¼ 200 m;
eB ¼ 900 m;
eC ¼ 1000 m
y The strain gage readings are typically corrected due to the effect of transverse strains on each gage. This will be discussed shortly.
92
Formulas for Stress and Strain
Figure 6.3
Three-element strain gage rosette.
[CHAP. 6
SEC.
6.2]
Experimental Methods
93
Determine the values and orientations of the principal stresses at the point. Let E ¼ 200 GPa and n ¼ 0:285. Solution. From above, ex ¼ eA ¼ 200 m;
ey ¼ eC ¼ 1000 m
gxy ¼ 2eB eA eC ¼ ð2Þð900Þ 200 1000 ¼ 600 m The stresses can be determined using Eqs. (2.2-5) and (2.2-6a): E ðe þ ney Þ 1 n2 x 200ð109 Þ ¼ ½200 þ ð0:285Þð1000Þ ð106 Þ ¼ 105:58ð106 Þ N=m2 ¼ 105:58 MPa 1 ð0:285Þ2 E ðe þ nex Þ sy ¼ 1 n2 y 200ð109 Þ ¼ ½1000 þ ð0:285Þð200Þ ð106 Þ ¼ 230:09ð106 Þ N=m2 ¼ 230:09 MPa 1 ð0:285Þ2 E 200ð109 Þ gxy ¼ 600ð106 Þ ¼ 46:69ð106 Þ N=m2 ¼ 46:69 MPa txy ¼ 2ð1 þ nÞ 2ð1 þ 0:285Þ sx ¼
Figure 6.4(a) shows the stresses determined in the x and y directions as related to the gage orientation shown in Fig. 6.3(a). For the principal stress axes, we use Eq. (2.3-23) given by qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 sp ¼ 2 ðsx þ sy Þ ðsx þ sy Þ2 þ 4t2xy qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ¼ 12 105:58 þ 230:09 ð105:58 þ 230:09Þ2 þ 4ð46:67Þ2 ¼ 245:65;
90:01 MPa
For the orientation of the principal stress axes, using the first of Eqs. (2.3-21) gives ! 1 sp sx ðaÞ yp ¼ tan txy For the principal stress, s1 ¼ 245:65 MPa, Eq. (a) gives 245:65 105:58 ¼ 71:6 yp1 ¼ tan1 46:69 For the other principal stress, s2 ¼ 90:01 MPa 90:01 105:58 ¼ 18:4 yp2 ¼ tan1 46:69 Recalling that yp is defined positive in the counterclockwise direction, the principal stress state at the point relative to the xy axes of the strain gage rosette correspond to that shown in Fig. 6.4(b).
94
Formulas for Stress and Strain
Figure 6.4
[CHAP. 6
(a) Stresses in the x and y directions. (b) Principal stresses.
Using the equations given in Table 6.1 at the end of the chapter, eA þ eC 200 þ 1000 ¼ 1678:3 m ¼ 1 0:285 1n qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 ðeA eC Þ2 þ ð2eB eA eC Þ2 1þn qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 ¼ ð200 1000Þ2 þ ½2ð900Þ 200 1000 2 ¼ 778:2 m 1 þ 0:285 Thus, sp1 ¼
200ð10Þ9 ð1678:3 þ 778:2Þ ¼ 245:65 MPa 2
sp2 ¼
200ð10Þ9 ð1678:3 778:2Þ ¼ 90:01 MPa 2
The principal angle is yp ¼
1 2ð900Þ 200 1000 1 þ600 1 tan1 ¼ tan1 ¼ ð143:13 Þ ¼ 71:6 2 200 1000 2 800 2
counterclockwise from the x axis (A gage) to sp1 ¼ 245:65 MPa.y Note that this agrees with Fig. 6.4(b).
y When calculating yp , do not change the signs of the numerator and denominator in the equation. The tan1 is defined from 0 to 360 . For example, tan1 ðþ=þÞ is in the range 0 –90 , tan1 ðþ=Þ is in the range 90 180 , tan1 ð=Þ is in the range 180 270 , and tan1 ð=þÞ is in the range 270 360 . Using this definition for yp, the calculation will yield the counterclockwise angle from the x axis to sp1 , the greater of the two principal stresses in the plane of the gages.
SEC.
6.2]
Experimental Methods
95
Strain Gage Corrections. There are many types of corrections that may
be necessary to obtain accurate strain gage results (see Refs. 27 and 28). Two fundamental corrections that are necessary correct the indicated strain errors due to strains on the specimen perpendicular (transverse) to the longitudinal axis of the gage and changes in temperature of the gage installation. With each strain gage, the manufacturer provides much information on the performance of the gage, such as its sensitivity to longitudinal and transverse strain and how the sensitivity of the gage behaves relative to temperature changes. (b) Transverse sensitivity corrections. The strain sensitivity of a single straight uniform length of conductor in a uniform uniaxial strain field e in the longitudinal direction of the conductor is given by Eq. (6.2-3), which is Sa ¼ ðDR=RÞ=e. In a general strain field, there will be strains perpendicular to the longitudinal axis of the conductor (transverse strains). Due to the width of the conductor elements and the geometric configuration of the conductor in the gage pattern, the transverse strains will also effect a change in resistance in the conductor. This is not desirable, since only the effect of the strain in the direction of the gage length is being sought. To further complicate things, the sensitivity of the strain gage provided by the gage manufacturer is not based on a uniaxial strain field, but that of a uniaxial stress field in a tensile test specimen. For a uniaxial stress field let the axial and transverse strains be ea and et respectively. The sensitivity provided by the gage manufacturer, called the gage factor Sg, is defined as Sg ¼ ðDR=RÞea , where under a uniaxial stress field, et ¼ n0 ea . Thus DR ¼ S g ea ; R
with
et ¼ n0 ea
(6.2-5)
The term n0 is Poisson’s ratio of the material on which the manufacturer’s gage factor was measured, and is normally taken to be 0.285. If the gage is used under conditions where the transverse strain is et ¼ nea , then the equation DR=R ¼ Sg ea would yield exact results. If et 6¼ n0 ea , then some error will occur. This error depends on the sensitivity of the gage to transverse strain and the deviation of the ratio of et =ea from n0 . The strain gage manufacturer generally supplies a transverse sensitivity coefficient, Kt , defined as St =Sa , where St is the transverse sensitivity factor. One cannot correct the indicated strain from a single strain reading. Thus it is necessary to have multiple strain readings from that of a strain gage rosette. Table 6.2 at the end of the chapter gives equations for the corrected strain values of the three most widely used strain gage rosettes. Corrected
96
Formulas for Stress and Strain
[CHAP. 6
strain readings are given by e; whereas uncorrected strains from the strain gage indicator are given by e^ . EXAMPLE In the previous example the indicated strains are e^ A ¼ 200 m, e^ B ¼ 900 m, and e^ C ¼ 1000 m. Determine the principal stresses and directions if the transverse sensitivity coefficient of the gages are KtA ¼ KtC ¼ 0:05 and KtB ¼ 0:06. Solution. From Table 6.2, eA ¼ ¼
ð1 n0 KtA Þ^eA KtA ð1 n0 KtC Þ^eC 1 KtA KtC ½1 ð0:285Þð0:05Þ ð200Þ ð0:05Þ½1 ð0:285Þð0:05Þ ð1000Þ 1 ð0:05Þð0:05Þ
¼ 148:23 m ð1 n0 KtB Þ^eB eB ¼
KtB ½ð1 n0 KtA Þð1 KtC Þ^eA þ ð1 n0 KtC Þð1 KtA Þ^eC 1 KtA KtC 1 KtB
¼ ½1 ð0:285Þð0:06Þ ð900Þ
0:06 ½1 ð0:05Þð0:05Þ !
f½1 ð0:285Þð0:05Þ ½1 0:05Þ ð200Þ þ ½1 ð0:285Þð0:05Þ ½1 0:05 ð1000Þg ð1 0:06Þ1 ¼ 869:17 m and eC ¼ ¼
ð1 n0 KtC Þ^eC KtC ð1 n0 KtA Þ^eA 1 KtA KtC ½1 ð0:285Þð0:05Þ ð1000Þ ð0:05Þ½1 ð0:285Þð0:05Þ ð200Þ 1 ð0:05Þð0:05Þ
¼ 978:34 m From Table 6.1,y eA þ eC 148:23 þ 978:34 ¼ 1575:62 m ¼ 1 0:285 1n qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 ðeA eC Þ2 þ ð2eB eA eC Þ2 1þn qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 ¼ ð148:23 978:34Þ2 þ ½2ð869:17Þ 148:23 978:34 2 ¼ 802:48 m 1 þ 0:285
y Note that if n for the specimen was different from n0 ¼ 0:285, it would be used in the equations of Table 6.1 but not for Table 6.2.
6.2]
SEC.
Experimental Methods
97
and sp1 ¼
200ð10Þ9 ð1575:62 þ 802:48Þð106 Þ ¼ 237:8ð106 Þ N=m2 ¼ 237:81 MPa 2
200ð10Þ9 ð1575:62 802:48Þð106 Þ ¼ 90:01ð106 Þ N=m2 ¼ 77:31 MPa 2 1 2ð869:17Þ 148:23 978:34 1 611:77 ¼ tan1 yp ¼ tan1 2 148:23 978:34 2 830:11
sp2 ¼
¼
1 ð143:61 Þ ¼ 71:8 2
The principal stress element is shown in Fig. 6.5 relative to the xy coordinate system of the gage rosette as shown in Fig. 6.3(a).
(b) Corrections due to temperature changes. Temperature changes on an installed strain gage cause a change in resistance, which is due to a mismatch in the thermal expansion coefficients of the gage and the specimen, a change in the resistivity of the gage material, and a change in the gage factor, Sg . This effect can be compensated for by two different methods. The first method of temperature compensation is achieved using an additional compensating gage on an adjacent arm of the Wheatstone bridge circuit. This compensating gage must be identical to the active gage, mounted on the same material as the active gage, and undergoing an identical temperature change as that of the active gage. The second method involves calibration of the gage relative to temperature changes. The gage can be manufactured and calibrated for the application on a specific specimen material. The metallurgical properties of alloys such as Constantan and modified Karma can be processed to minimize the effect of temperature change over a limited range of temperatures, somewhat centered about room temperature. Gages processed in this manner are called self-temperaturecompensated strain gages. An example of the characteristics of a
Figure 6.5
Principal stress element corrected for transverse sensitivity.
98
Formulas for Stress and Strain
[CHAP. 6
BLH self-temperature-compensated gage specifically processed for use on a low-carbon steel is shown in Fig. 6.6. Note that the apparent strain is zero at 22 C and 45 C and approximately zero in the vicinity of these temperatures. For temperatures beyond this region, compensation can be achieved by monitoring the temperature at the strain gage site. Then, using either the curve from the data sheet or the fitted polynomial equation, the strain readings can be corrected numerically. Note, however, that the curve and the polynomial equation given on the data sheet are based on a gage factor of 2.0. If corrections are anticipated, the gage factor adjustment of the strain indicator should be set to 2.0. An example that demonstrates this correction is given at the end of this section. The gage factor variation with temperature is also presented in the data sheet of Fig. 6.6. If the strain gage indicator is initially set at ðSg Þi , the actual gage factor at temperature T is ðSg ÞT , and the indicator registers a strain measurement of ereading , the corrected strain is
eactual ¼
ðSg Þi e ðSg ÞT reading
(6.2-6)
Strain gage temperature characteristsics. (Source: Data sheet courtesy BLH Electronics, Inc., Canton, MA.)
Figure 6.6
SEC.
6.2]
Experimental Methods
99
where
DSg ð%Þ ðSg ÞT ¼ 1 þ ðSg Þi 100
(6.2-7)
and DSg (%) being the percent variation in gage factor given in Fig. 6.6. If a simultaneous correction for apparent strain and gage factor variation is necessary, the corrected strain is given by eactual ¼
ðSg Þi ðe eapparent Þ ðSg ÞT reading
(6.2-8)
EXAMPLE A strain gage with the characteristics of Fig. 6.6 has a room-temperature gage factor of 2.1 and is mounted on a 1018 steel specimen. A strain measurement of 1800 m is recorded during the test when the temperature is 150 C. Determine the value of actual test strain if: (a) the gage is in a half-bridge circuit with a dummy temperature compensating gage and prior to testing, the indicator is zeroed with the gage factor set at 2.1. (b) the gage is the only gage in a quarter-bridge circuit and prior to testing, the indicator is zeroed with the gage factor set at 2.0. Solution. From Fig. 6.6, the gage factor variation at 150 C is DSg ð%Þ ¼ 1:13%. Thus, from Eq. (6.2-7), the gage factor at the test temperature is 1:13 ð2:1Þ ¼ 2:124 ðSg ÞT ¼ 1 þ 100
(a) Since in this part, a dummy gage is present that cancels the apparent strain, the only correction that is necessary is due to the change in the gage factor. From Eq. (6.2-6), eactual ¼
2:1 ð1800Þ ¼ 1780 m 2:124
which we see is a minor correction. (b) In this part, we must use Eq. (6.2-8). Using the equation given in Fig. 6.6, the apparent strain at the test temperature is eapparent ¼ 48:85 þ ð3:86Þð150Þ ð7:85E 02Þð150Þ2 þ ð4:05E 04Þð150Þ3 ð5:28E 07Þð150Þ4 ¼ 136:5 m
100
Formulas for Stress and Strain
[CHAP. 6
Substituting this into Eq. (6.2-8), with ðSg Þi ¼ 2:0, gives eactual ¼
2:0 ½1800 ð136:5Þ ¼ 1566 m 2:124
which is not a minor correction.
6.3
Detection of Plastic Yielding
In parts made of ductile metal, sometimes a great deal can be learned concerning the location of the most highly stressed region and the load that produces elastic failure by noting the first signs of plastic yielding. Such yielding may be detected in the following ways. Observation of slip lines. If yielding occurs first at some point on the
surface, it can be detected by the appearance of slip lines if the surface is suitably polished. If a member is coated with some material that will flake off easily, this flaking will indicate local yielding of the member. A coating of rosin or a wash of lime or white portland cement, applied and allowed to dry, is best for this purpose, but chalk or mill scale will often suffice. By this method zones of high stress such as those that occur in pressure vessels around openings and projections can be located and the load required to produce local yielding can be determined approximately.
Brittle coating.
Thin photoelastic coatings show very characteristic patterns analogous to slip lines when the material beneath the coating yields.
Photoelastic coatings.
6.4
Analogies
Certain problems in elasticity involve equations that cannot be solved but that happen to be mathematically identical with the equations that describe some other physical phenomenon which can be investigated experimentally. Among the more useful of such analogies are the following. Membrane analogy. This is especially useful in determining the
torsion properties of bars having noncircular sections. If in a thin flat plate holes are cut having the outlines of various sections and over each of these holes a soap film (or other membrane) is stretched and
SEC.
6.4]
Experimental Methods
101
slightly distended by pressure from one side, the volumes of the bubbles thus formed are proportional to the torsional rigidities of the corresponding sections and the slope of a bubble surface at any point is proportional to the stress caused at that point of the corresponding section by a given twist per unit length of bar. By cutting in the plate one hole the shape of the section to be studied and another hole that is circular, the torsional properties of the irregular section can be determined by comparing the bubble formed on the hole of that shape with the bubble formed on the circular hole since the torsional properties of the circular section are known. Isopachic lines are lines along which the sums of the principal stresses are equal in a twodimensional plane stress problem. The voltage at any point on a uniform two-dimensional conducting surface is governed by the same form of equation as is the principal stress sum. Teledeltos paper is a uniform layer of graphite particles on a paper backing and makes an excellent material from which to construct the electrical analog. The paper is cut to a geometric outline corresponding to the shape of the two-dimensional structure or part, and boundary potentials are applied by an adjustable power supply. The required boundary potentials are obtained from a photoelastic study of the part where the principal stress sums can be found from the principal stress differences on the boundaries (Refs. 2 and 3). A similar membrane analogy has the height of a nonpressurized membrane proportional to the principal stress sum (Refs. 2 and 3).
Electrical analogy for isopachic lines.
102
6.5
Formulas for Stress and Strain
[CHAP. 6
Tables
TABLE 6.1
Strain gage rosette equations applied to a specimen of a linear, isotropic material
The principal strains and stresses are given relative to the xy coordinate axes as shown.
Three-element rectangular rosette
Principal strains qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi eA þ eC 1 þ ðeA eC Þ2 þ ð2eB eA eC Þ2 2 2 qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi e þ eC 1 ¼ A ðeA eC Þ2 þ ð2eB eA eC Þ2 2 2
ep1 ¼ ep2 Principal stresses
qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi E eA þ eC 1 þ ðeA eC Þ2 þ ð2eB eA eC Þ2 2 1n 1þn qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi E eA þ eC 1 ¼ ðeA eC Þ2 þ ð2eB eA eC Þ2 2 1n 1þn
sp1 ¼ sp2
Principal angle Treating the tan1 as a single-valued function,y the angle counterclockwise from gage A to the axis containing ep1 or sp1 is given by 1 2eB eA eC yp ¼ tan1 2 eA eC y
See Example in Sec. 6.2. (continued)
SEC.
6.5]
Experimental Methods
103
TABLE 6.1
Strain gage rosette equations applied to a specimen of a linear, isotropic material (Continued)
Three-element delta rosette
Principal strains pffiffiffi qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi eA þ eB þ eC 2 þ ðeA eB Þ2 þ ðeB eC Þ2 þ ðeC eA Þ2 3 3 pffiffiffi qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2 e þ þe ðeA eB Þ2 þ ðeB eC Þ2 þ ðeC eA Þ2 ¼ A B C 3 3
ep1 ¼ ep2 Principal stresses sp1
sp2
" pffiffiffi qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi# 2 E eA þ eB þ eC þ ðeA eB Þ2 þ ðeB eC Þ2 þ ðeC eA Þ2 ¼ 3 1n 1þn " pffiffiffi qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi# 2 E eA þ eB þ eC ¼ ðeA eB Þ2 þ ðeB eC Þ2 þ ðeC eA Þ2 3 1n 1þn
Principal angle Treating the tan1 as a single-valued functiony the angle counterclockwise from gage A to the axis containing ep1 or sp1 is given by pffiffiffi 1 3ðeC eB Þ yp ¼ tan1 2 2eA eB eC y
See Example (as applied to a rectangular rosette) in Sec. 6.2.
104
Formulas for Stress and Strain
TABLE 6.2
[CHAP. 6
Corrections for the transverse sensitivity of electrical resistance strain
gages e refers to corrected strain value, whereas e^ refers to the strain read from the strain indicator. The Kt terms are the transverse sensitivity coefficients of the gages as supplied by the manufacturer. Poisson’s ratio, n0 , is normally given to be 0.285.
Two-element rectangular rosette
ð1 n0 KtA Þ^eA KtA ð1 n0 KtB Þ^eB 1 KtA KtB ð1 n0 KtB Þ^eB KtB ð1 n0 KtA Þ^eA ey ¼ 1 KtA KtB
ex ¼
Three-element rectangular rosette
ð1 n0 KtA Þ^eA KtA ð1 n0 KtC Þ^eC 1 KtA KtC KtB ð1 n0 KtB Þ^eB ½ð1 n0 KtA Þð1 KtC Þ^eA þ ð1 n0 KtC Þð1 KtA Þ^eC 1 KtA KtC eB ¼ 1 KtB ð1 n0 KtC Þ^eC KtC ð1 n0 KtA Þ^eA eC ¼ 1 KtA KtC eA ¼
SEC.
6.6]
Experimental Methods
105
Three-element delta rosette
eA ¼ kfð1 n0 KtA Þð3 KtB KtC KtB KtC Þ^eA 2KtA ½ð1 n0 KtB Þð1 KtC Þ^eB þ ð1 n0 KtC Þð1 KtB Þ^eC g eB ¼ kfð1 n0 KtB Þð3 KtC KtA KtC KtA Þ^eB 2KtB ½ð1 n0 KtC Þð1 KtA Þ^eC þ ð1 n0 KtA Þð1 KtC Þ^eA g eC ¼ kfð1 n0 KtC Þð3 KtA KtB KtA KtB Þ^eC 2KtC ½ð1 n0 KtA Þð1 KtB Þ^eA þ ð1 n0 KtB Þð1 KtA Þ^eB g where k ¼ ð3KtA KtB KtC KtA KtB KtB KtC KtA KtC KtA KtB KtC þ 3Þ1
6.6
References
1. Proc. Soc. Exp. Stress Anal., 1943–1960; Exp. Mech., J. Soc. Exp. Stress Anal., from Jan. 1, 1961 to June 1984; and Exp. Mech., J. Soc. Exp. Mechanics after June 1984. 2. Hete´ nyi, M. (ed.): ‘‘Handbook of Experimental Stress Analysis,’’ John Wiley & Sons, 1950. 3. Dally, J. W., and W. F. Ri]ey: ‘‘Experimental Stress Analysis,’’ 2nd ed., McGraw-Hill, 1978. 4. Dove, R. C., and P. H. Adams: ‘‘Experimental Stress Analysis and Motion Measurement,’’ Charles E. Merrill Books, 1955. 5. Holister, G. S.: ‘‘Experimental Stress Analysis: Principles and Methods,’’ Cambridge University Press, 1967. 6. Frocht, MI. M.: ‘‘Photoelasticity,’’ vols. 1 and 2, John Wiley & Sons, 1941, 1948. 7. Durelli, A. J.: ‘‘Applied Stress Analysis,’’ Prentice-Hall, 1967. 8. Durelli, A. J., and V. J. Parks: ‘‘Moire´ Analysis of Strain,’’ Prentice-Hall, 1970. 9. Durelli, A. J., E. A. Phillips, and C. H. Tsao: ‘‘Introduction to the Theoretical and Experimental Analysis of Stress and Strain,’’ Prentice-Hall, 1958. 10. Durelli, A. J., and W. F. Riley: ‘‘Introduction to Photomechanics,’’ Prentice-Hall, 1965. 11. Theocaris, P. S.: ‘‘Moire´ Fringes in Strain Analysis,’’ Pergamon Press, 1969. 12. Savin, G. N.: ‘‘Stress Concentration around Holes,’’ Pergamon Press, 1961. 13. Liebowitz, H. (ed.): ‘‘Fracture,’’ Academic Press, 1968. 14. Heywood, R. B.: ‘‘Photoelasticity for Designers,’’ Pergamon Press, 1969. 15. Sih, G. C.: ‘‘Handbook of Stress Intensity Factors,’’ Institute of Fracture and Solid Mechanics, Lehigh University, 1973. 16. Javornicky, J.: ‘‘Photoplasticity,’’ Elsevier Scientific, 1974.
106
Formulas for Stress and Strain
[CHAP. 6
17. Kobayashi, A. S. (ed.): ‘‘Experimental Techniques in Fracture Mechanics, 1 and 2,’’ Iowa State University Press, 1973 and 1975. 18. Aben, H.: ‘‘Integrated Photoelasticity,’’ McGraw-Hill, 1979. 19. Broek, D.: ‘‘Elementary Engineering Fracture Mechanics,’’ Martinus Nijhoff, 1982. 20. Kobayashi, A. S. (ed.): ‘‘Manual of Engineering Stress Analysis,’’ 3rd ed., PrenticeHall, 1982. 21. Kobayashi, A. S. (ed.): ‘‘Manual on Experimental Stress Analysis,’’ 4th ed., Society of Experimental Mechanics, 1983. 22. Atluri, S. N. (ed): ‘‘Computational Methods in the Mechanics of Fracture,’’ NorthHolland, 1984. 23. Dally, J. W., W. F. Riley, and K. G. McConnell: ‘‘Instrumentation for Engineering Measurements,’’ John Wiley & Sons, 1984. 24. Int. J. Anal. Exp. Modal Anal., journal of the Society of Experimental Mechanics. 25. J. Strain Analysis, journal of the Institution of Mechanical Engineers. 26. Strain, journal of the British Society for Strain Measurement. 27. Kobayashi, A. S., (ed.): ‘‘Handbook on Experimental Mechanics,’’ 2nd ed., Society for Experimental Mechanics, VCH, 1993. 28. Budynas, R. G.: ‘‘Advanced Strength and Applied Stress Analysis,’’ 2nd ed., McGrawHill, 1999.
Part
3 Formulas and Examples
Each of the following chapters deals with a certain type of structural member or a certain condition of stress. What may be called the common, or typical, case is usually discussed first; special cases, representing peculiarities of form, proportions, or circumstances of loading, are considered subsequently. In the discussion of each case the underlying assumptions are stated, the general behavior of the loaded member is described, and formulas for the stress and deformation are given. The more important of the general equations are numbered consecutively throughout each section to facilitate reference, but, wherever possible, formulas applying to specific cases are tabulated for convenience and economy of space. In all formulas which contain numerical constants having dimensions, the units are specified. Most formulas contain only dimensionless constants and can be evaluated in any consistent system of units.
Chapter
7 Tension, Compression, Shear, and Combined Stress
7.1 Bar under Axial Tension (or Compression); Common Case The bar is straight, of any uniform cross section, of homogeneous material, and (if under compression) short or constrained against lateral buckling. The loads are applied at the ends, centrally, and in such a manner as to avoid nonuniform stress distribution at any section of the part under consideration. The stress does not exceed the proportional limit. Behavior. Parallel to the load the bar elongates (under tension) or
shortens (under compression), the unit longitudinal strain being e and the total longitudinal deflection in the length l being d. At right angles to the load the bar contracts (under tension) or expands (under compression); the unit lateral strain e0 is the same in all transverse directions, and the total lateral deflection d0 in any direction is proportional to the lateral dimension d measured in that direction. Both longitudinal and lateral strains are proportional to the applied load. On any right section there is a uniform tensile (or compressive) stress s; on any oblique section there is a uniform tensile (or compressive) normal stress sy and a uniform shear stress ty . The deformed bar under tension is represented in Fig. 7.1(a), and the stresses in Fig. 7.1(b). 109
110
Formulas for Stress and Strain
[CHAP. 7
Figure 7.1
Formulas.
Let P ¼ applied load A ¼ cross-sectional area ðbefore loadingÞ l ¼ length ðbefore loadingÞ E ¼ modulus of elasticity n ¼ Poisson0 s ratio
Then s¼ sy ¼
P A
ð7:1-1Þ
P cos2 y; A
P sin 2y; 2A s e¼ E
t¼
d ¼ le ¼
max sy ¼ s ðwhen y ¼ 0 Þ max ty ¼
1 sðwhen y ¼ 45 or 135 Þ 2 ð7:1-2Þ
Pl AE
ð7:1-3Þ
e0 ¼ ne
ð7:1-4Þ
d0 ¼ e 0 d
ð7:1-5Þ 1 s2 2E
ð7:1-6Þ
1 s2 1 Al ¼ Pd 2E 2
ð7:1-7Þ
Strain energy per unit volume U ¼
Total strain energy U ¼
For small strain, each unit area of cross section changes by ð2neÞ under load, and each unit of volume changes by ð1 2nÞe under load. In some discussions it is convenient to refer to the stiffness of a member, which is a measure of the resistance it offers to being
SEC.
7.2]
Tension, Compression, Shear, and Combined Stress
111
deformed. The stiffness of a uniform bar under axial load is shown by Eq. (7.1-3) to be proportional to A and E directly and to l inversely, i.e., proportional AE=l. EXAMPLE A cylindrical rod of steel 4 in long and 1.5 in diameter has an axial compressive load of 20,000 lb applied to it. For this steel n ¼ 0:285 and E ¼ 30;000;000 lb=in2 . Determine (a) the unit compressive stress s; (b) the total longitudinal deformation, d; (c) the total transverse deformation d0 ; (d) the change in volume, DV ; and (e) the total energy, or work done in applying the load. Solution (a) s ¼
P 4P 4ð20;000Þ ¼ ¼ ¼ 11;320 lb=in2 A pd2 pð1:5Þ2
(b) e ¼
s 11;320 ¼ ¼ 377ð106 Þ E 30;000;000
d ¼ el ¼ ð377Þð106 Þð4Þ ¼ 1:509ð103 Þ in ð00 00 means shorteningÞ (c) e0 ¼ ne ¼ 0:285ð377Þð106 Þ ¼ 107:5ð106 Þ d0 ¼ e0 d ¼ ð107:5Þð106 Þð1:5Þ ¼ 1:613ð104 Þ in ð00 þ00 means expansionÞ (d) DV =V ¼ ð1 2nÞe ¼ ½1 2ð0:285Þ ð377Þð106 Þ ¼ 162:2ð106 Þ p p DV ¼ 162:2ð106 ÞV ¼ 162:2ð106 Þ d2 l ¼ 162:2ð106 Þ ð1:5Þ2 ð4Þ 4 4 ¼ 1:147ð103 Þ in3 ð00 00 means decreaseÞ (e) Increase in strain energy, U¼
7.2
1 1 Pd ¼ ð20;000Þð1:509Þð103 Þ ¼ 15:09 in-lb 2 2
Bar under Tension (or Compression); Special Cases
If the bar is not straight, it is subject to bending; formulas for this case are given in Sec. 12.4. If the load is applied eccentrically, the bar is subject to bending; formulas for this case are given in Secs. 8.7 and 12.4. If the load is compressive and the bar is long and not laterally constrained, it must be analyzed as a column by the methods of Chapters 12 and 15. If the stress exceeds the proportional limit, the formulas for stress given in Sec. 7.1 still hold but the deformation and work done in producing it can be determined only from experimental data relating unit strain to unit stress.
112
Formulas for Stress and Strain
[CHAP. 7
If the section is not uniform but changes gradually, the stress at any section can be found by dividing the load by the area of that ðsection; l P dx the total longitudinal deformation over a length l is given by ðl AE 2 0 1P and the strain energy is given by dx, where dx is an infinite0 2 AE simal length in the longitudinal direction. If the change in section is abrupt stress concentration may have to be taken into account, values of Kt being used to find elastic stresses and values of Kr being used to predict the breaking load. Stress concentration may also have to be considered if the end attachments for loading involve pinholes, screw threads, or other stress raisers (see Sec. 3.10 and Chap. 17). If instead of being applied at the ends of a uniform bar the load is applied at an intermediate point, both ends being held, the method of consistent deformations shows that the load is apportioned to the two parts of the bar in inverse proportion to their respective lengths. If a uniform bar is supported at one end in a vertical position and loaded only by its own weight, the maximum stress occurs at the supported end and is equal to the weight divided by the cross-sectional area. The total elongation is half as great and the total strain energy one-third as great as if a load equal to the weight were applied at the unsupported end. A bar supported at one end and loaded by its own weight and an axial downward load P (force) applied at the unsupported end will have the same unit stress s (force per unit area) at all sections if it is tapered so that all sections are similar in form but vary in scale according to the formula y¼
s As loge w P
ð7:2-1Þ
where y is the distance from the free end of the bar to any section, A is the area of that section, and w is the density of the material (force per unit volume). If a bar is stressed by having both ends rigidly held while a change in temperature is imposed, the resulting stress is found by calculating the longitudinal expansion (or contraction) that the change in temperature would produce if the bar were not held and then calculating the load necessary to shorten (or lengthen) it by that amount (principle of superposition). If the bar is uniform, the unit stress produced is independent of the length of the bar if restraint against buckling is provided. If a bar is stressed by being struck an axial blow at one end, the case is one of impact loading, discussed in Sec. 16.3. EXAMPLES 1. Figure 7.2 represents a uniform bar rigidly held at the ends A and D and axially loaded at the intermediate points B and C. It is required to determine
SEC.
7.2]
Tension, Compression, Shear, and Combined Stress
113
Figure 7.2
the total force in each portion of the bar AB, BC, CD. The loads are in newtons and the lengths in centimeters. Solution. Each load is divided between the portions of the bar to right and left in inverse proportion to the lengths of these parts (consistent deformations), and the total force sustained by each part is the algebraic sum of the forces imposed by the individual loads (superposition). Of the 9000 N load, therefore, 79, or 7000 N, is carried in tension by segment AB, and 29, or 2000 N, is carried in compression by the segment BD. Of the 18,000 N load, 49, or 8000 N, is carried in compression by segment AC, and 59, or 10,000 N, is carried in tension by segment CD. Denoting tension by the plus sign and compression by the minus sign, and adding algebraically, the actual stresses in each segment are found to be AB: BC: CD:
7000 8000 ¼ 1000 N 2000 8000 ¼ 10;000 N 2000 þ 10;000 ¼ þ8000 N
The results are quite independent of the diameter of the bar and of E provided the bar is completely uniform. If instead of being held at the ends, the bar is prestressed by wedging it between rigid walls under an initial compression of, say, 10,000 N and the loads at B and C are then applied, the results secured above would represent the changes in force the several parts would undergo. The final forces in the bar would therefore be 11,000 N compression in AB, 20,000 N compression in BC, and 2000 N compression in CD. But if the initial compression were less than 8000 N, the bar would break contact with the wall at D (no tension possible); there would be no force at all in CD, and the forces in AB and BC, now statically determinate, would be 9000 and 18,000 N compression, respectively. 2. A steel bar 24 in long has the form of a truncated cone, being circular in section with a diameter at one end of 1 in and at the other of 3 in. For this steel, E ¼ 30;000;000 lb=in2 and the coefficient of thermal expansion is 0:0000065= F. This bar is rigidly held at both ends and subjected to a drop in temperature of 50 F. It is required to determine the maximum tensile stress thus caused. Solution. Using the principle of superposition, the solution is effected in three steps: (a) the shortening d due to the drop in temperature is found, assuming the bar free to contract; (b) the force P required to produce an elongation equal to d, that is, to stretch the bar back to its original length, is calculated; (c) the maximum tensile stress produced by this force P is calculated. (a) d ¼ 50(0.0000065)(24) ¼ 0.00780 in. (b) Let d denote the diameter and A the area of any section a distance x in
114
Formulas for Stress and Strain
[CHAP. 7
from the small end of the bar. Then d¼1þ
x ; 12
A¼
p x 2 1þ 4 12
and ðl
P dx ¼ d¼ EA 0
ð 24 0
24 4P ð12Þ dx ¼ ¼ 3:395ð107 ÞP pð30Þð106 Þ ð1 þ x=12Þ ðpEÞð1 þ x=12Þ2 0 4P
Equating this to the thermal contraction of 0.00780 in yields P ¼ 22;970 lb (c) The maximum stress occurs at the smallest section, and is s¼
4P 4ð22;970Þ ¼ ¼ 29;250 lb=in2 pd2min pð1Þ2
The result can be accepted as correct only if the proportional limit of the steel is known to be as great as or greater than the maximum stress and if the concept of a rigid support can be accepted. (See cases 8, 9, and 10 in Table 14.1.)
7.3
Composite Members
A tension or compression member may be made up of parallel elements or parts which jointly carry the applied load. The essential problem is to determine how the load is apportioned among the several parts, and this is easily done by the method of consistent deformations. If the parts are so arranged that all undergo the same total elongation or shortening, then each will carry a portion of the load proportional to its stiffness, i.e., proportional to AE=l if each is a uniform bar and proportional to AE if all these uniform bars are of equal length. It follows that if there are n bars, with section areas A1 ; A2 ; . . . ; An , lengths l1 ; l2 ; . . . ; ln , and moduli E1 , E2 ; . . . ; En , then the loads on the several bars P1 , P2 ; . . . ; Pn are given by A1 E1 l1 P1 ¼ P A1 E1 A2 E2 A E þ þ
þ n n l1 l2 ln
ð7:3-1Þ
A2 E2 l2 P2 ¼ P A1 E1 A2 E2 A E þ þ
þ n n l1 l2 ln
ð7:3-2Þ
::::::::::::::::::::::::::::::::::::::::::::::::::::::::
SEC.
7.3]
Tension, Compression, Shear, and Combined Stress
115
A composite member of this kind can be prestressed. P1 , P2 , etc., then represent the increments of force in each member due to the applied load, and can be found by Eqs. (7.3-1) and (7.3-2), provided all bars can sustain reversal of stress, or provided the applied load is not great enough to cause such reversal in any bar which cannot sustain it. As explained in Sec. 3.12, by proper prestressing, all parts of a composite member can be made to reach their allowable loads, elastic limits, or ultimate strengths simultaneously (Example 2). EXAMPLES 1. A ring is suspended by three vertical bars, A, B, and C of unequal lengths. The upper ends of the bars are held at different levels, so that as assembled none of the bars is stressed. A is 4 ft long, has a section area of 0:3 in2 , and is of steel for which E ¼ 30;000;000 lb=in2 ; B is 3 ft long and has a section area of 0:2 in2 , and is of copper for which E ¼ 17;000;000 lb=in2 ; C is 2 ft long, has a section area of 0:4 in2 , and is of aluminum for which E ¼ 10;000;000 lb=in2 . A load of 10,000 lb is hung on the ring. It is required to determine how much of this load is carried by each bar. Solution. Denoting by PA, PB , and PC the loads carried by A, B, and C, respectively, and expressing the moduli of elasticity in millions of pounds per square inch and the lengths in feet, we substitute in Eq. (7.3-1) and find 2
3 ð0:3Þð30Þ 6 7 4 PA ¼ 10;0004 5 ¼ 4180 lb ð0:3Þð30Þ ð0:2Þð17Þ ð0:4Þð10Þ þ þ 4 3 2 Similarly PB ¼ 2100 lb
and
PC ¼ 3720 lb
2. A composite member is formed by passing a steel rod through an aluminum tube of the same length and fastening the two parts together at both ends. The fastening is accomplished by adjustable nuts, which make it possible to assemble the rod and tube so that one is under initial tension and the other is under an equal initial compression. For the steel rod the section area is 1:5 in2 , the modulus of elasticity 30,000,000 lb=in2 and the allowable stress 15,000 lb=in2 . For the aluminum tube the section area is 2 in2 , the modulus of elasticity 10,000,000 lb=in2 and the allowable stress 10,000 lb=in2 . It is desired to prestress the composite member so that under a tensile load both parts will reach their allowable stresses simultaneously. Solution. When the allowable stresses are reached, the force in the steel rod will be 1.5(15,000) ¼ 22,500 lb, the force in the aluminum tube will be 2(10,000) ¼ 20,000 lb, and the total load on the member will be 22,500 þ 20,000 ; ¼ 42,500 lb. Let Pi denote the initial tension or compression in the members, and, as before, let tension be considered positive and compression negative. Then, since Eq. (7.3-1) gives the increment in force,
116
Formulas for Stress and Strain
[CHAP. 7
we have for the aluminum tube Pi þ 42;500
ð2Þð10Þ ¼ 20;000 ð2Þð10Þ þ ð1:5Þð30Þ
or Pi ¼ þ 6920 lb
ðinitial tensionÞ
For the steel rod, we have Pi þ 42;500
ð1:5Þð30Þ ¼ 22;500 ð2Þð10Þ þ ð1:5Þð30Þ
or Pi ¼ 6920 lb
ðinitial compressionÞ
If the member were not prestressed, the unit stress in the steel would always be just three times as great as that in the aluminum because it would sustain the same unit deformation and its modulus of elasticity is three times as great. Therefore, when the steel reached its allowable stress of 15,000 lb=in2 , the aluminum would be stressed to only 5000 lb=in2 and the allowable load on the composite member would be only 32,500 lb instead of 42,500 lb.
7.4
Trusses
A conventional truss is essentially an assemblage of straight uniform bars that are subjected to axial tension or compression when the truss is loaded at the joints. The deflection of any joint of a truss is easily found by the method of unit loads (Sec. 4.5). Let p1 , p2 , p3 , etc., denote the forces produced in the several members by an assumed unit load acting in the direction x at the joint whose deflection is to be found, and let d1 , d2 , d3 , etc., denote the longitudinal deformations produced in the several members by the actual applied loads. The deflection Dx in the direction x of the joint in question is given by Dx ¼ p1 d1 þ p2 d2 þ p3 d3 þ ¼
n P
p i di
ð7:4-1Þ
i¼1
The deflection in the direction y, at right angles to x, can be found similarly by assuming the unit load to act in the y direction; the resultant deflection is then determined by combining the x and y deflections. Attention must be given to the signs of p and d, p is positive if a member is subjected to tension and negative if under compression, and d is positive if it represents an elongation P and negative if it represents a shortening. A positive value for pd means that the deflection is in the direction of the assumed unit
SEC.
7.4]
Tension, Compression, Shear, and Combined Stress
117
load, and a negative value means that it is in the opposite direction. (This procedure is illustrated in Example 1 below.) A statically indeterminate truss can be solved by the method of least work (Sec. 4.5). To do this, it is necessary to write down the expression for the total strain energy in the structure, which, being simply the sum of the strain energies of the constituent bars, is given by n 1 n 1 P2l P P 1 1 1 P d þ P d þ P d þ
¼ Pi di ¼ ð7:4-2Þ 2 1 1 2 2 2 2 3 3 i¼1 2 i¼1 2 AE i Here P1 , P2 , etc., denote the forces in the individual members due to the applied loads and d has the same meaning as above. It is necessary to express each force Pi as the sum of the two forces; one of these is the force the applied loads would produce with the redundant member removed, and the other is the force due to the unknown force (say, F) exerted by this redundant member on the rest of the structure. The total strain energy is thus expressed as a function of the known applied forces and F, the force in the redundant member. The partial derivative with respect to F of this expression for strain energy is then set equal to zero and solved for F. If there are two or more redundant members, the expression for strain energy with all the redundant forces, F1 , F2 , etc., represented is differentiated once with respect to each. The equations thus obtained are then solved simultaneously for the unknown forces. (The procedure is illustrated in Example 2.) EXAMPLES 1. The truss shown in Fig. 7.3 is composed of tubular steel members, for which E ¼ 30;000;000 lb=in2 . The section areas of the members are given in the table below. It is required to determine Dx and Dy , the horizontal and vertical components of the displacement of joint A produced by the indicated loading. Solution. The method of unit loads is used. The force P in each member due to the applied loads is found, and the resulting elongation or shortening d is calculated. The force px in each member due to a load of 1 lb acting to the right at A, and the force py in each P member due to a load of 1 lb actingPdown at A are calculated. By Eq. (7.4-1), px d, then gives the horizontal and py d gives the vertical displacement or deflection of A. Tensile forces and elongations are
Figure 7.3
118
Formulas for Stress and Strain
[CHAP. 7
denoted by þ , compressive forces and shortenings by . The work is conveniently tabulated as follows: Pl Area, Length, di ¼ , in 2 li , in Pi , lb Member Ai , in ðpx Þi AE i (1) (2) (3) (4) (5) (6)
AB AC BC BE BD CD
0.07862 0.07862 0.1464 0.4142 0.3318 0.07862
48 60 36 48 60 48
800 1000 1200 4000 4000 800
0.01628 0.02544 0.00984 0.01545 0.02411 0.01628
1.000 0 0 1.000 0 0
ðpx dÞi , in (a)
ðpy dÞi , in (b)
ðpy Þi
0.01628 1.333 0 1.667 0 1.000 0.01545 2.667 0 1.667 0 1.333
Dx ¼ 0:03173 in
0.02171 0.04240 0.00984 0.04120 0.04018 0.02171
Dy ¼ 0:17704 in
Dx and Dy are both found to be positive, which means that the displacements are in the directions of the assumed unit loads—to the right and down. Had either been found to be negative, it would have meant that the displacement was in a direction opposite to that of the corresponding unit load. 2. Assume a diagonal member, running from A to D and having a section area 0:3318 in2 and length 8.544 ft, is to be added to the truss of Example 1; the structure is now statically indeterminate. It is required to determine the force in each member of the altered truss due to the loads shown. Solution. We use the method of least work. The truss has one redundant member; any member except BE may be regarded as redundant, since if any one were removed, the remaining structure would be stable and statically determinate. We select AD to be regarded as redundant, denote the unknown force in AD by F, and assume F to be tension. We find the force in each member assuming AD to be removed, then find the force in each member due to a pull F exerted at A by AD, and then add these forces, thus getting an expression for the force in each member of the actual truss in terms of F. The expression for the strain energy can then be written out, differentiated with respect to F, equated to zero, and solved for F. F being known, the force in each member of the truss is easily found. The computations are conveniently tabulated as follows: Forces in membersy
Member (1) (2) (3) (4) (5) (6) (7) y
AB AC BC BE BD CD AD
Due to applied loads without AD (a) (lb) 800 1000 1200 4000 4000 800 0
Due to pull, F, exerted by AD (b)
Total forces, Pi . Superposition of (a) and (b) (c)
Actual total values with F ¼ 1050 lb in (c) (d) (lb)
0.470 F 0.584 F 0.351 F 0 0.584 F 0.470 F F
800 0:470 F 1000 0:584 F 1200 þ 0:351 F 4000 4000 0:584 F 800 0:470 F F
1290 390 830 4000 3390 306 1050
þ for tension and for compression.
SEC.
7.5]
Tension, Compression, Shear, and Combined Stress
119
" 7 1 P2l P 1 ð800 0:470FÞ2 ð48Þ ð1000 0:584FÞ2 ð60Þ þ U¼ ¼ 2E 0:07862 0:07862 i¼1 2 AE i ð1200 þ 0:351FÞ2 ð36Þ ð4000Þ2 ð48Þ þ 0:1464 0:4142 2 ð4000 0:584FÞ ð60Þ ð800 0:470FÞ2 ð48Þ þ þ 0:3318 0:07862 2 F ð102:5Þ þ 0:3318
þ
Setting the partial derivative of U relative to F to zero, @U 1 2ð800 0:470FÞð0:470Þð48Þ 2ð1000 0:584FÞð0:584Þð60Þ ¼ þ þ
@F 2E 0:07862 0:07862 ¼0 and solving for F gives F ¼ 1050 lb. The negative sign here simply means that AD is in compression. A positive value of F would have indicated tension. Substituting the value of F into the terms of column (c) yield the actual total forces in each member as tabulated in column (d).
7.5
Body under Pure Shear Stress
A condition of pure shear may be produced by any one of the methods of loading shown in Fig. 7.4. In Fig. 7.4(a), a rectangular block of length a, height b, and uniform thickness t is shown loaded by forces P1 and P2 , uniformly distributed over the surfaces to which they are applied and satisfying the equilibrium equation P1 b ¼ P2 a. There are equal shear stresses on all vertical and horizontal planes, so that any contained cube oriented like ABCD has on each of four faces the shear stress t ¼ P1 =at ¼ P2 =bt and no other stress. In Fig. 7.4(b) a rectangular block is shown under equal and opposite biaxial stresses st and sc . There are equal shear stresses on all planes inclined at 45 to the top and bottom faces, so that a contained cube
Figure 7.4
120
Formulas for Stress and Strain
[CHAP. 7
oriented like ABCD has on each of four faces the shear stress t ¼ st ¼ sc and no other stress. In Fig. 7.4(c), a circular shaft is shown under a twisting moment T ; a cube of infinitesimal dimensions, a distance z from the axis and oriented like ABCD has on each of four faces an essentially uniform shear stress t ¼ Tz=J (Sec. 10.1) and no other stress. In whatever way the loading is accomplished, the result is to impose on an elementary cube of the loaded body the condition of stress represented in Fig. 7.5, that is, shearing stress alone on each of four faces, these stresses being equal and so directed as to satisfy the equilibrium condition Tx ¼ 0 (Sec. 4.1). The stresses, sy and ty on a transformed surface rotated counterclockwise through the angle y can be determined from the transformation equations given by Eqs. (2.3-17). They are given by sy ¼ t sin 2y;
ty ¼ t cos 2y
ð7:5-1Þ
where ðsy Þmax;min ¼ t at y ¼ 45 . The strains produced by pure shear are shown in Fig. 7.5(b), where the cube ABCD is deformed into a rhombohedron A0 B0 C 0 D0 . The unit shear strain, g, referred to as the engineering shear strain, is reduction of angles ff ABC and ff ADC, and the increase in angles ff DAB and ff BCD in radians. Letting G denote the modulus of rigidity, the shear strain is related to the shear stress as g¼
t G
ð7:5-2Þ
Assuming a linear material, the strain energy per unit volume for pure shear, us , within the elastic range is given by us ¼
Figure 7.5
1 t2 2G
(a) Shear stress and transformation. (b) Shear strain.
ð7:5-3Þ
SEC.
7.7]
Tension, Compression, Shear, and Combined Stress
121
The relations between t, s, and the strains represented in Fig. 7.5(b) make it possible to express G in terms of E and Poisson’s ratio, n, for a linear, homogeneous, isotropic material. The relationship is G¼
E 2ð1 þ nÞ
ð7:5-4Þ
From known values of E (determined by a tensile test) and G (determined by a torsion test) it is thus possible to calculate n. 7.6
Cases of Direct Shear Loading
By direct shear loading is meant any case in which a member is acted on by equal, parallel, and opposite forces so nearly colinear that the material between them is subjected primarily to shear stress, with negligible bending. Examples of this are provided by rivets, bolts, and pins, shaft splines and keys, screw threads, short lugs, etc. These are not really cases of pure shear; the actual stress distribution is complex and usually indeterminate because of the influence of fit and other factors. In designing such parts, however, it is usually assumed that the shear is uniformly distributed on the critical section, and since working stresses are selected with due allowance for the approximate nature of this assumption, the practice is usually permissible. In beams subject to transverse shear, this assumption cannot be made as a rule. Shear and other stresses in rivets, pins, keys, etc., are discussed more fully in Chap. 14, shear stresses in beams in Chap. 8, and shear stresses in torsion members in Chap. 10. 7.7
Combined Stress
Under certain circumstances of loading, a body is subjected to a combination of tensile and compressive stresses (usually designated as biaxial or triaxial stress) or to a combination of tensile, compressive, and shear stresses (usually designated as combined stress). For example, the material at the inner surface of a thick cylindrical pressure vessel is subjected to triaxial stress (radial compression, longitudinal tension, and circumferential tension), and a shaft simultaneously bent and twisted is subjected to combined stress (longitudinal tension or compression, and torsional shear). In most instances the normal and shear stresses on each of three mutually perpendicular planes are due to flexure, axial loading, torsion, beam shear, or some combination of these which separately can be calculated readily by the appropriate formulas. Normal stresses arising from different load conditions acting on the same plane can be
122
Formulas for Stress and Strain
[CHAP. 7
combined simply by algebraic addition considering tensile stresses positive and compressive stresses negative. Similarly, shear stresses can be combined by algebraic addition following a consistent sign convention. Further analysis of the combined states of normal and shear stresses must be performed using the transformation techniques outlined in Sec. 2.3. The principal stresses, the maximum shear stress, and the normal and shear stresses on any given plane can be found by the equations given in Sec. 2.3. The strains produced by any combination of stresses not exceeding the proportional limit can also be found using Hooke’s law for each stress and then combined by superposition. Consideration of the strains caused by equal triaxial stresses leads to an expression for the bulk modulus of elasticity given by K¼
E 3ð1 2nÞ
ð7:7-1Þ
EXAMPLES 1. A rectangular block 12 in long, 4 in high, and 2 in thick is subjected to a longitudinal tensile stress sx ¼ 12;000 lb=in2 , a vertical compressive stress sy ¼ 15;000 lb=in2 , and a lateral compressive stress sz ¼ 9000 lb=in2 . The material is steel, for which E ¼ 30;000;000 lb=in2 and n ¼ 0:30. It is required to find the total change in length. Solution. The longitudinal deformation is found by superposition: The unit strain due to each stress is computed separately by Eqs. (7.1-2) and (7.1-4); these results are added to give the resultant longitudinal unit strain, which is multiplied by the length to give the total elongation. Denoting unit longitudinal strain by ex and total longitudinal deflection by dx , we have 12;000 15;000 9000 n n E E E ¼ 0:000400 þ 0:000150 þ 0:000090 ¼ þ0:00064 dx ¼ 12ð0:00064Þ ¼ 0:00768 in ex ¼
The lateral dimensions have nothing to do with the result since the lateral stresses, not the lateral loads, are given. 2. A piece of ‘‘standard extra-strong’’ pipe, 2 in nominal diameter, is simultaneously subjected to an internal pressure of p ¼ 2000 lb=in2 and to a twisting moment of T ¼ 5000 in-lb caused by tightening a cap screwed on at one end. Determine the maximum tensile stress and the maximum shear stress thus produced in the pipe. Solution. The calculations will be made, first, for a point at the outer surface and, second, for a point at the inner surface. The dimensions of the pipe and properties of the cross section are as follows: inner radius ri ¼ 0:9695 in, outer radius ro ¼ 1:1875 in, cross-sectional area of bore Ab ¼ 2:955 in2 , cross-sectional area of pipe wall Aw ¼ 1:475 in2 , and polar moment of inertial J ¼ 1:735 in4 .
SEC.
7.7]
Tension, Compression, Shear, and Combined Stress
123
We take axis x along the axis of the pipe, axis y tangent to the cross section, and axis z radial in the plane of the cross section. For a point at the outer surface of the pipe, sx is the longitudinal tensile stress due to pressure and sy is the circumferential (hoop) stress due to pressure, the radial stress sz ¼ 0 (since the pressure is zero on the outer surface of the pipe), and txy is the shear stress due to torsion. Equation (7.1-1) can be used for sx, where P ¼ pAb and A ¼ Aw . To calculate sy , we use the formula for stress in thick cylinders (Table 13.5, case 1b). Finally, for txy, we use the formula for torsional stress (Eq. (10.1-2). Thus,
sx ¼
pAb ð2000Þð2:955Þ ¼ 4007 lb=in2 ¼ 1:475 Aw
sy ¼ p txy ¼
r2i ðr2o þ r2o Þ ð0:96952 Þð1:18752 þ 1:18752 Þ ¼ 2000 ¼ 7996 lb=in2 2 2 2 ð1:18752 Þð1:18752 0:96952 Þ ro ðro ri Þ
Tro ð5000Þð1:1875Þ ¼ 3422 lb=in2 ¼ 1:735 J
This is a case of plane stress where Eq. (2.3-23) applies. The principal stresses are thus qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ðsx sy Þ2 þ 4t2xy qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ¼ 12 ½ð4007 þ 7996Þ ð4007 7996Þ2 þ 4ð34222 Þ ¼ 9962;
sp ¼ 12 ½ðsx þ sy Þ
2041 lb=in2
Thus, smax ¼ 9962 lb=in2 . In order to determine the maximum shear stress, we order the three principal stresses such that s1 5 s2 5 s3 . For plane stress, the out-of-plane principal stresses are zero. Thus, s1 ¼ 9962 lb=in2 , s2 ¼ 2041 lb=in2 , and s3 ¼ 0. From Eq. (2.3-25), the maximum shear stress is tmax ¼ 12 ðs1 s3 Þ ¼ 12 ð9962 0Þ ¼ 4981 lb=in2 For a point on the inner surface, the stress conditions are three-dimensional since a radial stress due to the internal pressure is present. The longitudinal stress is the same; however, the circumferential stress and torsional shear stress change. For the inner surface, sx ¼ 4007 lb=in2 sy ¼ p
r2o þ r2i 1:18752 þ 0:96952 ¼ 2000 ¼ 9996 lb=in2 1:18752 0:96952 r2o r2i
sz ¼ p ¼ 2000 lb=in2 txy ¼
Tri ð5000Þð0:9695Þ ¼ 2794 lb=in2 ¼ 1:735 J
tyz ¼ tzx ¼ 0
124
Formulas for Stress and Strain
[CHAP. 7
The principal stresses are found using Eq. (2.3-20):y s3p ð4007 þ 9996 2000Þs2p þ ½ð4007Þð9996Þ þ ð9996Þð2000Þ þ ð2000Þð4007Þ 27942 0 0 sp ½ð4007Þð9996Þð2000Þ þ 2ð2794Þð0Þð0Þ ð4007Þð02 Þ ð9996Þð02 Þ ð2000Þð27942 Þ ¼ 0 or s3p 12:003ð103 Þs2p þ 4:2415ð106 Þsp þ 64:495ð109 Þ ¼ 0
Solving this gives sp ¼ 11;100; 2906, and 2000 lb=in2 , which are the principal stresses s1 , s2 , and s3 , respectively. Obviously, the maximum tensile stress is 11;100 lb=in2 . Again, the maximum shear stress comes from Eq. (2.3-25), and is 12 ½11;100 ð2000Þ ¼ 6550 lb=in2 . Note that for this problem, if the pipe is a ductile material, and one were looking at failure due to shear stress (see Sec. 3.7), the stress conditions for the pipe are more severe at the inner surface compared with the outer surface.
y Note: Since tyz ¼ tzx ¼ 0, sz is one of the principal stresses and the other two can be found from the plane stress equations. Consequently, the other two principal stresses are in the xy plane.
Chapter
8 Beams; Flexure of Straight Bars
8.1
Straight Beams (Common Case) Elastically Stressed
The formulas in this section are based on the following assumptions: (1) The beam is of homogeneous material that has the same modulus of elasticity in tension and compression. (2) The beam is straight or nearly so; if it is slightly curved, the curvature is in the plane of bending and the radius of curvature is at least 10 times the depth. (3) The cross section is uniform. (4) The beam has at least one longitudinal plane of symmetry. (5) All loads and reactions are perpendicular to the axis of the beam and lie in the same plane, which is a longitudinal plane of symmetry. (6) The beam is long in proportion to its depth, the span=depth ratio being 8 or more for metal beams of compact section, 15 or more for beams with relatively thin webs, and 24 or more for rectangular timber beams. (7) The beam is not disproportionately wide (see Sec. 8.11 for a discussion on the effect of beam width). (8) The maximum stress does not exceed the proportional limit. Applied to any case for which these assumptions are not valid, the formulas given yield results that at best are approximate and that may be grossly in error; such cases are discussed in subsequent sections. The limitations stated here with respect to straightness and proportions of the beam correspond to a maximum error in calculated results of about 5%. In the following discussion, it is assumed for convenience that the beam is horizontal and the loads and reactions vertical. Behavior. As the beam bends, fibers on the convex side lengthen, and
fibers on the concave side shorten. The neutral surface is normal to the plane of the loads and contains the centroids of all sections, hence the neutral axis of any section is the horizontal central axis. Plane sections 125
126
Formulas for Stress and Strain
[CHAP. 8
remain plane, and hence unit fiber strains and stresses are proportional to distance from the neutral surface. Longitudinal displacements of points on the neutral surface are negligible. Vertical deflection is largely due to bending, that due to shear being usually negligible under the conditions stated. There is at any point a longitudinal fiber stress s, which is tensile if the point lies between the neutral and convex surfaces of the beam and compressive if the point lies between the neutral and concave surfaces of the beam. This fiber stress s usually may be assumed uniform across the width of the beam (see Secs. 8.11 and 8.12). There is at any point a longitudinal shear stress t on the horizontal plane and an equal vertical shear stress on the transverse plane. These shear stresses, due to the transverse beam forces, may be assumed uniform across the width of the beam (see page 129). Figure 8.1(a,b) represent a beam under load and show the various dimensions that appear in the formulas; Fig. 8.1(c) shows a small stress element at a point q acted on by the stresses s and t. Formulas. Let I ¼ the moment of inertia of the section of the beam with respect to the neutral axis and E ¼ modulus of elasticity of the material. The fiber stress s at any point q is
s¼
Figure 8.1
My I
ð8:1-1Þ
SEC.
8.1]
Beams; Flexure of Straight Bars
127
where M is the bending moment at the section containing q, and y is the vertical distance from the neutral axis to q. The shear stress t at any point q is t¼
VA0 y Ib
ð8:1-2Þ
where V is the vertical shear at the section containing q, A0 is the area of that part of the section above (or below) q; y is the distance from the neutral axis to the centroid of A0 , and b is the net breadth of the section measured through q. The complementary energy of flexure Uf , is ð 2 M Uf ¼ dx ð8:1-3Þ 2EI where M represents the bending moment equation in terms of x, the distance from the left end of the beam to any section. The radius of curvature r of the elastic curve at any section is r¼
EI M
ð8:1-4Þ
where M is the bending moment at the section in question. The general differential equation of the elastic curve is EI
d2 y c ¼M dx2
ð8:1-5Þ
where M has the same meaning as in Eq. (8.1-3) and yc represents the vertical deflection of the centroidal axis of the beam. Solution of this equation for the vertical deflection yc is effected by writing out the expression for M, integrating twice, and determining the constants of integration by the boundary conditions. By the method of unit loads the vertical deflection at any point is found to be ð Mm yc ¼ dx ð8:1-6Þ EI or by Castigliano’s second theorem it is found to be yc ¼
@U @P
ð8:1-7Þ
where M has the same meaning as in Eq. (8.1-3) and m is the equation of the bending moment due to a unit load acting vertically at the section where yc is to be found. The integration indicated must be performed over each portion of the beam for which either M or m is expressed by a different equation. A positive result for yc means that
128
Formulas for Stress and Strain
[CHAP. 8
the deflection is in the direction of the assumed unit load; a negative result means it is in the opposite direction (see Example 2 at the end of this section). In Eq. (8.1-7), U is given by Eq. (8.1-3) and P is a vertical load, real or imaginary, applied at the section where yc is to be found. It is most convenient to perform the differentiation within the integral sign; as with Eq. (8.1-6), the integration must extend over the entire length of the beam, and the sign of the result is interpreted as before. The change in slope of elastic curve Dy (radians) between any two sections a and b is ðb
M dx EI a
Dy ¼
ð8:1-8Þ
where M has the same meaning as in Eq. (8.1-3). The deflection Dyc at any section a, measured vertically from a tangent drawn to the elastic curve at any section b, is ðb Dyc ¼
M x dx a EI
ð8:1-9Þ
where x is the distance from a to any section dx between a and b. Important relations between the bending moment and shear equations are dM dx ð M ¼ V dx V ¼
ð8:1-10Þ ð8:1-11Þ
These relations are useful in constructing shear and moment diagrams and locating the section or sections of maximum bending moment since Eq. (8.1-10) shows that the maximum moment occurs when V , its first derivative, passes through zero and Eq. (8.1-11) shows that the increment in bending moment that occurs between any two sections is equal to the area under the shear diagram between those sections. Maximum fiber stress. The maximum fiber stress at any section occurs
at the point or points most remote from the neutral axis and is given by Eq. (8.1-1) when y ¼ c; hence smax ¼
Mc M M ¼ ¼ I I=c S
ð8:1-12Þ
SEC.
8.1]
Beams; Flexure of Straight Bars
129
where S is the section modulus. The maximum fiber stress in the beam occurs at the section of greatest bending moment; if the section is not symmetrical about the neutral axis, the stresses should be investigated at both the section of greatest positive moment and the section of greatest negative moment. Maximum transverse shear stress.y
The maximum transverse shear stress in the beam occurs at the section of greatest vertical shear. The maximum transverse shear stress at any section occurs at the neutral axis, provided the net width b is as small there as anywhere else; if the section is narrower elsewhere, the maximum shear stress may not occur at the neutral axis. This maximum transverse shear stress can be expressed conveniently by the formula ðtmax ÞV ¼ a
V A
ð8:1-13Þ
where V =A is the average shear stress on the section and a is a factor that depends on the form of the section. For a rectangular section, a ¼ 32 and the maximum stress is at the neutral axis; for a solid circular section, a ¼ 43 and the maximum stress is at the neutral axis; for a triangular section, a ¼ 32 and the maximum stress is halfway between the top and bottom of the section; for a diamond-shaped section of depth h, a ¼ 98 and the maximum stress is at points that are a distance h=8 above and below the neutral axis. In the derivation of Eq. (8.1-2) and in the preceding discussion, it is assumed that the shear stress is uniform across the width of the beam; i.e., it is the same at all points on any transverse line parallel to the neutral axis. Actually this is not the case; exact analysis (Ref. 1) shows that the shear stress varies across the width and that for a rectangle the maximum intensity occurs at the ends of the neutral axis where, for a wide beam, it is twice the average intensity. Photoelastic investigation of beams under concentrated loading shows that localized shearing stresses about four times as great as the maximum stress given by Eq. (8.1-2) occur near the points of loading and support (Ref. 2), but experience shows that this variation may be ignored and design based on the average value as determined by Eq. (8.1-2).
y Note that the transverse shear stress denoted here is the shear stress due to the vertical transverse force, V . The maximum transverse shear stress in a beam is not necessarily the maximum shear stress in the beam. One needs to look at the overall state of stress in light of stress transformations. For long beams, the maximum shear stress is normally due to the maximum fiber stress, and, using Eq. (2.3-25), the maximum shear stress is tmax ¼ 12 smax ¼ 12 M=S. For this reason, we will denote the maximum transverse shear stress in a beam as ðtmax ÞV .
130
Formulas for Stress and Strain
[CHAP. 8
For some sections the greatest horizontal shear stress at a given point occurs, not on a horizontal plane, but on an inclined longitudinal plane which cuts the section so as to make b a minimum. Thus, for a circular tube or pipe the greatest horizontal shear stress at any point occurs on a radial plane; the corresponding shear stress in the plane of the section is not vertical but tangential, and in computing t by Eq. (8.1-2) b should be taken as twice the thickness of the tube instead of the net horizontal breadth of the member. (See Table 9.2, case 20 for an example of where this shear stress in a tube is of importance.) In an I-, T-, or box section there is a horizontal shear stress on any vertical longitudinal plane through the flange, and this stress is usually a maximum at the juncture of flange and web. It may be calculated by Eq. (8.1-2), taking A0 as the area outside of the vertical plane (for outstanding flanges) or between the vertical plane and the center of the beam section (for box girders), and b as the flange thickness (see the solution to Example lb). The other terms have the same meanings as explained previously. Shear stresses are not often of controlling importance except in wood or metal beams that have thin webs or a small span=depth ratio. For beams that conform to the assumptions stated previously, strength will practically always be governed by fiber stress. The apparent shortening of a beam due to bending, i.e., the difference between its original length and the horizontal projection of the elastic curve, is given by
Change in projected length due to bending.
1 Dl ¼ 2
ðl 0
dy dx
2 dx
ð8:1-14Þ
To evaluate Dl, dy=dx is expressed in terms of x [Eq. (8.1-5)] and the square of this is integrated as indicated. The extreme fibers of the beam undergo a change in actual length due to stress given by ðl e¼
Mc dx 0 EI
ð8:1-15Þ
By means of these equations the actual relative horizontal displacement of points on the upper or lower surface of the beam can be predicted and the necessary allowances made in the design of rocker bearings, clearance for the corners, etc. Table 8.1 gives formulas for the reactions, moments, slopes and deflections at each end of single-span beams supported and loaded in various ways. The table also gives formulas
Tabulated formulas.
SEC.
8.1]
Beams; Flexure of Straight Bars
131
for the vertical shears, bending moments, slopes, and deflections at any distance x from the left end of the span. In these formulas, the unit step function is used by itself and in combination with ordinary functions. The unit step function is denoted by hx ai0 where the use of the angle brackets h i is defined as follows: If x < a, hx ai0 ¼ 0; if x > a, hx ai0 ¼ 1. At x ¼ a the unit step function is undefined just as vertical shear is undefined directly beneath a concentrated load. The use of the angle brackets h i is extended to other cases involving powers of the unit step function and the ordinary function ðx aÞn . Thus the quantity ðx aÞn hx ai0 is shortened to hx ain and again is given a value of zero if x < a and is ðx aÞn if x > a. In addition to the usual concentrated vertical loads, concentrated couples, and distributed loads, Table 8.1 also presents cases where the loading is essentially a development of reactions due to deformations created within the span. These cases include the concentrated angular displacement, concentrated transverse deflection, and linear temperature differential across the beam from top to bottom. In all three cases it can be assumed that initially the beam was deformed but free of stress and then is forced to conform to the end conditions. (In many cases no forces are created, and the formulas give only the deformed shape.) Hete´ nyi (Ref. 29) discusses in detail the Maclaurin series form of the equations used in this article and suggests (Ref. 53) that the deformation type of loading might be useful in solving beam problems. Thomson (Ref. 65) describes the use of the unit step function in the determination of beam deflections. By superposition, the formulas can be made to apply to almost any type of loading and support. The use of the tabulated and fundamental formulas given in this article is illustrated in the following examples. EXAMPLES 1. For a beam supported and loaded as shown in Fig. 8.2, it is required to determine the maximum tensile stress, maximum shear stress, and maximum compressive stress, assuming, first, that the beam is made of wood with section as shown in Fig. 8.2(a) second, that the beam is made of wood with section as shown in Fig. 8.2(b); and third that the beam is a 4-in, 7.7-lb steel Ibeam. Solution. By using the equations of equilibrium (Sec. 4.1), the left and right reactions are found to be 900 and 1500 lb, respectively. The shear and moment equations are therefore ðx ¼ 0 to x ¼ 160Þ:
V ¼ 900 12x M ¼ 900x 12xð12 xÞ
ðx ¼ 160 to x ¼ 200Þ:
V ¼ 900 12x þ 1500 M ¼ 900x 12xð12 xÞ þ 1500ðx 160Þ
132
Formulas for Stress and Strain
[CHAP. 8
Figure 8.2
Using the step function described previously, these equations can be reduced to V ¼ 900 12x þ 1500hx 160i0 M ¼ 900x 6x2 þ 1500hx 160i These equations are plotted, giving the shear and moment diagrams shown in Fig. 8.2. The maximum positive moment evidently occurs between the supports; the exact location is found by setting the first shear equation equal to zero and solving for x, which gives x ¼ 75 in. Substitution of this value of x in the first moment equation gives M ¼ 33;750 lb-in. The maximum negative moment occurs at the right support where the shear diagram again passes through zero and is 9600 lb-in. The results obtained so far are independent of the cross section of the beam. The stresses will now be calculated for each of the sections (a), (b), and (c). 1 (a) For the rectangular section: I ¼ 12 bd3 ¼ 86:2 in4 ; I=c ¼ 16 bd2 ¼ 23:1 in3 ; 2 and A ¼ bd ¼ 18:60 in . Therefore
smax ¼
Mmax 33;750 ¼ 1460 lb=in2 ¼ 23:1 I=c
½by Eq: ð8:1-12Þ
This stress occurs at x ¼ 75 in and is tension in the bottom fibers of the beam and compression in the top. The maximum transverse shear stress isy tmax ¼
3 Vmax 3 1020 ¼ ¼ 82 lb=in2 2 A 2 18:60
½by Eq: ð8:1-13Þ
which is the horizontal and vertical shear stress at the neutral axis of the section just to the left of the right support. (b) For the routed section it is found (Appendix A) that the neutral axis is 4 in from the base of the section and I ¼ 82:6 in4 . The maximum transverse shear stress on a horizontal plane occurs at the neutral axis since b is as small there as anywhere, and so in Eq. (8.1-2) the product A0 y represents the statical y The actual maximum shear stress for this example is found from a stress transformation of the maximum bending stress. Thus, at the outer fibers of the beam at x ¼ 75, tmax ¼ 12 smax ¼ 12 1460 ¼ 730 lb=in2 .
SEC.
8.1]
Beams; Flexure of Straight Bars
133
moment about the neutral axis of all that part of the section above the neutral axis. Taking the moment of the flange and web portions separately, we find A0 y ¼ ð2:75Þð2:3Þð2:30Þ þ ð1Þð1:15Þð0:575Þ ¼ 15:2 in3 . Also, b ¼ 1:00 in. Since the section is not symmetrical about the neutral axis, the fiber stresses will be calculated at the section of maximum positive moment and at the section of maximum negative moment. We have 8 ð33;750Þð4Þ > > ¼ 1630 lb=in2 ðtension in bottom fiberÞ < 82:6 At x ¼ 75 in: s ¼ > > : ð33;750Þð3:45Þ ¼ 1410 lb=in2 ðcompression in top fiberÞ 82:6 8 ð9600Þð4Þ > > ¼ 456 lb=in2 ðcompression in bottom fiberÞ < 82:6 At x ¼ 160 in: s ¼ > > : ð9600Þð3:45Þ ¼ 400 lb=in2 ðtension in top fibersÞ 82:6 It is seen that for this beam the maximum fiber stresses in both tension and compression occur at the section of maximum positive bending moment. The maximum transverse shear stress is ðtmax ÞV ¼
ð1020Þð15:2Þ ¼ 188 lb=in2 ð82:6Þð1Þ
½by Eq: ð8:1-2Þ
This is the maximum shear stress on a horizontal plane and occurs at the neutral axis of the section just to the left of the right support. The actual maximum shear stress is tmax ¼ 12 smax ¼ 12 1630 ¼ 815 lb=in2 . (c) For the steel I-beam, the structural steel handbook gives I=c ¼ 3:00 in3 and t ¼ 0:190 in. Therefore smax ¼
33;750 ¼ 11;250 lb=in2 3
This stress occurs at x ¼ 75 in, where the beam is subject to tension in the bottom fibers and compression in the top. The maximum transverse shear stress is approximated by ðtmax ÞV
1020 ¼ 1340 lb=in2 ð4Þð0:19Þ
Although this method of calculating t (where the shear force is assumed to be carried entirely by the web) is only approximate, it is usually sufficiently accurate to show whether or not this shear stress is important. If it indicates that this shear stress may govern, then the stress at the neutral axis may be calculated by Eq. (8.1-2). For standard I-beams, the allowable vertical shear is given by the structural-steel handbooks, making computation unnecessary. 2. The beam is shown in Fig. 8.3 has a rectangular section 2 in wide and 4 in deep and is made of spruce, where E ¼ 1;300;000 lb=in2 . It is required to determine the deflection of the left end. Solution. The solution will be effected first by superposition, using the formulas of Table 8.1. The deflection y of the left end is the sum of the
134
Formulas for Stress and Strain
[CHAP. 8
Figure 8.3
deflection y1 produced by the distributed load and the deflection y2 produced by the concentrated load. Each of these is computed independently of the other and added using superposition. Thus 1 ð2:14Þð1403 Þ 9;800;000 ¼þ y1 ¼ 40y ¼ ð40Þ 24 EI EI by formula for y at A, case 2e, where a ¼ 0, l ¼ 140 in and wa ¼ wl ¼ 2:14 lb=in. y2 is calculated as the sum of the deflection the 150-lb load would produce if the beam were fixed at the left support and the deflection produced by the fact that it actually assumes a slope there. The first part of the deflection is given by the formula for max y (case 1a), and the second part is found by multiplying the overhang (40 in) by the slope produced at the left end of the 140-in span by a counterclockwise couple equal to 150ð40Þ ¼ 6000 lb-in applied at that point (formula for y at A, case 3e, where a ¼ 0). 1 ð150Þð403 Þ 1 ð6000Þð140Þ 14;400;000 y2 ¼ þ ð40Þ ¼ 3 EI 3 EI EI Adding algebraically, the deflection of the left end is y ¼ y1 þ y2 ¼
4;600;000 ¼ 0:33 in EI
ðdeflection is downwardÞ
The solution of this problem can also be effected readily by using Eq. (8.1-6). The reaction at the left support due to the actual loads is 343 lb and the reaction due to a unit load acting down at the left support is 1.286. If x is measured from the extreme left end of the beam M ¼ 150x þ 343hx 40i 2:14
hx 40i2 2
and m ¼ x þ 1:286hx 40i
Simplifying the equations, we have ð Mm y¼ dx EI ð 40 ð 180 1 ð150xÞðxÞdx þ ð1:071x2 þ 278:8x 15;430Þð0:286x 51:6Þdx ¼ EI 0 40 ¼ þ0:33 in (Here the plus sign means that y is in the direction of the assumed unit load, i.e., downward.) This second solution involves much more labor than the first, and the calculations must be carried out with great accuracy to avoid the possibility of making a large error in the final result.
SEC.
8.1]
Beams; Flexure of Straight Bars
135
3. A cast iron beam is simply supported at the left end and fixed at the right end on a span of 100 cm. The cross section is 4 cm wide and 6 cm deep ðI ¼ 72 cm4 Þ. The modulus of elasticity of cast iron is 107 N=cm2 , and the coefficient of expansion is 0:000012 cm=cm= C. It is desired to determine the locations and magnitudes of the maximum vertical deflection and the maximum bending stress in the beam. The loading consists of a uniformly increasing distributed load starting at 0 at 40 cm from the left end and increasing to 200 N=cm at the right end. In addition, the beam, which was originally 20 C, is heated to 50 C on the top and 100 C on the bottom with the temperature assumed to vary linearly from top to bottom. Solution. Superimposing cases 2c and 6c of Table 8.1, the following reactions are determined. (Note: For case 2c, wa ¼ 0, a ¼ 40 cm, wl ¼ 200 N=cm, and l ¼ 100 cm; for case 6c, T1 ¼ 50 C, T2 ¼ 100 C, g ¼ 0:000012 cm=cm= C, t ¼ 6 cm, and a ¼ 0.) 200ð100 40Þ3 ð4 100 þ 40Þ 3ð107 Þð72Þð0:000012Þð100 50Þ ¼ 604:8 N 40ð1003 Þ 2ð6Þð100Þ MA ¼ 0 yA ¼ 0 RA ¼
200ð100 40Þ3 ð2 100 þ 3 40Þ 0:000012ð100 50Þð100Þ þ 240ð107 Þð72Þð100Þ 4ð6Þ ¼ 0:0033 rad
yA ¼
Therefore
y ¼ 0:0033x
604:8x3 200hx 40i5 0:000012ð100 50Þx2 þ 6EI ð100 40Þð120ÞEI 2ð6Þ
¼ 0:0033x 1:4ð107 Þx3 3:86ð1011 Þhx 40i5 þ 5:0ð105 Þx2 and dy ¼ 0:0033 4:2ð107 Þx2 19:3ð1011 Þhx 40i4 þ 10ð105 Þx dx The maximum deflection will occur at a position x1 where the slope dy=dx is zero. At this time an assumption must be made as to which span, x1 < 40 or x1 > 40, will contain the maximum deflection. Assuming that x1 is less than 40 cm and setting the slope equal to zero, 0 ¼ 0:0033 4:2ð107 Þx21 þ 10ð105 Þx1 Of the two solutions for x1, 39.7 and 198 cm, only the value of 39.7 cm is valid since it is less than 40 cm. Substituting x ¼ 39:7 cm into the deflection equation gives the maximum deflection of 0:061 cm. Similarly, M ¼ 604:8x
200 hx 40i3 6ð100 40Þ
136
Formulas for Stress and Strain
[CHAP. 8
which has a maximum negative value where x is a maximum, i.e., at the right end: 200 ð100 40Þ3 ¼ 180;480 N-cm 6ð100 40Þ Mc 180;480ð3Þ ¼ ¼ ¼ 7520 N=cm2 I 72
Mmax ¼ 604:8ð100Þ smax
4. The cast iron beam in Example 3 is to be simply supported at both ends and carry a concentrated load of 10,000 N at a point 30 cm from the right end. It is desired to determine the relative displacement of the lower edges of the end section. For this example, case 1e can be used with a ¼ 70 cm: 10;000ð100 70Þ ¼ 3000 N MA ¼ 0 100 10;000ð70Þ ð200 70Þð100 70Þ ¼ 0:00632 rad; yA ¼ 6ð107 Þð72Þð100Þ 10;000ð70Þ yB ¼ ð1002 702 Þ ¼ 0:00826 rad 6ð107 Þð72Þð100Þ
RA ¼
yA ¼ 0
Then dy 10;000 ¼ 0:00632 þ 2:083ð106 Þx2 hx 70i2 dx 2ð107 Þð72Þ ¼ 0:00632 þ 2:083ð106 Þx2 6:94ð106 Þhx 70i2 The shortening of the neutral surface of the beam is given in Eq. (8.1-14) to be ð l 2 dy dx 0 dx ð 70 1 ½0:00632 þ 2:083ð106 Þx2 2 dx ¼ 2 0 ð 1 100 ½0:04033 þ 9:716ð104 Þx 4:857ð106 Þx2 2 dx þ 2 70
Dl ¼
1 2
or Dl ¼ 0:00135 cm
ða shorteningÞ
In addition to the shortening of the neutral surface, the lower edge of the left end moves to the left by an amount yA c or 0.00632(3) ¼ 0.01896 cm. Similarly, the lower edge of the right end moves to the right by an amount yB c or 0.00826(3) ¼ 0.02478 cm. Evaluating the motion of the lower edges in this manner is equivalent to solving Eq. (8.1-15) for the total strain in the lower fibers of the beam. The total relative motion of the lower edges of the end sections is therefore a moving apart by an amount 0.01896 þ 0.02478 0.00135 ¼ 0.0424 cm.
SEC.
8.2
8.2]
Beams; Flexure of Straight Bars
137
Composite Beams and Bimetallic Strips
Beams that are constructed of more than one material can be treated by using an equivalent width technique if the maximum stresses in each of the several materials remain within the proportional limit. An equivalent cross section is developed in which the width of each component parallel to the principal axis of bending is increased in the same proportion that the modulus of elasticity of that component makes with the modulus of the assumed material of the equivalent beam. EXAMPLE The beam cross section shown in Fig. 8.4(a) is composed of three portions of equal width and depth. The top portion is made of aluminum for which EA ¼ 10 106 lb=in2 ; the center is made of brass for which EB ¼ 15 106 lb=in2 ; and the bottom is made of steel for which ES ¼ 30 106 lb=in2 . Figure 8.4(b) shows the equivalent cross section, which is assumed to be made of aluminum. For this equivalent cross section the centroid must be located and the moment of inertia determined for the centroidal axis. Solution 3ð2Þð5Þ þ 4:5ð2Þð3Þ þ 9ð2Þð1Þ ¼ 2:27 in 6 þ 9 þ 18 3ð23 Þ 4:5ð23 Þ 9ð23 Þ þ 6ð5 2:27Þ2 þ þ 9ð3 2:27Þ2 þ þ 18ð2:27 1Þ2 Ix ¼ 12 12 12 ¼ 89:5 in4 y ¼
The equivalent stiffness EI of this beam is therefore 10 106 ð89:5Þ, or 895 106 lb-in2 . A flexure stress computed by s ¼ Mc=Ix will give a stress in the equivalent beam which can thereby be converted into the stress in the actual composite beam by multiplying by the modulus ratio. If a bending moment of 300,000 lbin were applied to a beam with the cross section shown, the stress at the top surface of the equivalent beam would be s ¼ 300;000ð6 2:27Þ=89:5, or 12,500 lb=in2 . Since the material at the top is the same in both the actual and equivalent beams, this is also the maximum stress in the aluminum portion of the actual beam. The stress at the bottom of the equivalent beam would be s ¼ 300;000ð2:27Þ=89:5 ¼ 7620 lb=in2 . Multiplying the stress by the
Figure 8.4
138
Formulas for Stress and Strain
[CHAP. 8
modulus ratio, the actual stress at the bottom of the steel portion of the beam would be s ¼ 7620ð30=10Þ ¼ 22;900 lb=in2 .
Bimetallic strips are widely used in instruments to sense or control temperatures. The following formula gives the equivalent properties of the strip for which the cross section is shown in Fig. 8.5: Equivalent EI ¼
wt3b ta Eb Ea K 12ðta Ea þ tb Eb Þ 1
ð8:2-1Þ
or K1 ¼ 4 þ 6
2 3 ta t E t E t þ4 a þ a a þ b b tb tb Eb tb Ea ta
ð8:2-2Þ
All the formulas in Table 8.1, cases 1 to 5, can be applied to the bimetallic beam by using this equivalent value of EI. Since a bimetallic strip is designed to deform when its temperature differs from To , the temperature at which the strip is straight, Table 8.1, case 6, can be used to solve for reaction forces and moments as well as deformations of the bimetallic strip under a uniform temperature T . To do this, the term gðT2 T1 Þ=t is replaced by the term 6ðgb ga ÞðT To Þðta þ tb Þ= ðt2b K1 Þ and EI is replaced by the equivalent EI given by Eq. (8.2-1). After the moments and deformations have been determined, the flexure stresses can be computed. The stresses due to the bending moments caused by the restraints and any applied loads are given by the following expressions: In the top surface of material a: 6M t E t s¼ 2 2þ bþ a a ð8:2-3Þ ta Eb tb wtb K1 In the bottom surface of material b: 6M t E t 2þ aþ b b s¼ 2 tb Ea ta wtb K1
ð8:2-4Þ
If there are no restraints imposed, the distortion of a bimetallic strip due to a temperature change is accompanied by flexure stresses in the two materials. This differs from a beam made of a single material which deforms free of stress when subjected to a linear temperature
Figure 8.5
SEC.
8.2]
Beams; Flexure of Straight Bars
139
variation through the thickness if there are no restraints. Therefore the following stresses must be added algebraically to the stresses caused by the bending moments, if any: In the top surface of material a: " # 2 ðgb ga ÞðT To ÞEa ta ta Eb tb s¼ 3 þ2 ð8:2-5Þ K1 tb tb Ea ta In the bottom surface of material b: " 3 # ðgb ga ÞðT To ÞEb ta Ea ta s¼ 3 þ2 K1 tb Eb tb
ð8:2-6Þ
EXAMPLE A bimetallic strip is made by bonding a piece of titanium alloy 14 in wide by 0.030 in thick to a piece of stainless steel 14 in wide by 0.060 in thick. For titanium, E ¼ 17 106 lb=in2 and g ¼ 5:7 106 in=in= F; for stainless steel, E ¼ 28 106 lb=in2 and g ¼ 9:6 106 in=in= F. It is desired to find the length of bimetal required to develop a reaction force of 5 oz at a simply supported left end when the right end is fixed and the temperature is raised 50 F; also the maximum stresses must be determined. Solution. First find the value of K1 from Eq. (8.2-2) and then evaluate the equivalent stiffness from Eq. (8.2-1): 2 3 0:03 0:03 17 0:03 28 0:06 þ4 ¼ 11:37 þ þ 0:06 0:06 28 0:06 17 0:03 0:25ð0:063 Þð0:03Þð28 106 Þð17 106 Þ Equivalent EI ¼ 11:37 ¼ 333 lb-in2 12½0:03ð17 106 Þ þ 0:06ð28 106 Þ K1 ¼ 4 þ 6
Under a temperature rise over the entire length, the bimetallic strip curves just as a single strip would curve under a temperature differential. To use case 6c in Table 8.1, the equivalent to gðT2 T1 Þ=t must be found. This equivalent value is given by 6ð9:6 106 5:7 106 Þð50Þð0:03 þ 0:06Þ ¼ 0:00257 in1 ð0:062 Þð11:37Þ The expression for RA can now be obtained from case 6c in Table 8.1 and, noting that a ¼ 0, the value of the length l can be determined: RA ¼
3ðl2 a2 Þ g 3 5 ð333Þð0:00257Þ ¼ lb EI ðT2 T1 Þ ¼ 2l3 t 2l 16
Therefore l ¼ 4:11 in. The maximum bending moment is found at the fixed end and is equal to RA l: 5 ð4:11Þ ¼ 1:285 lb-in max M ¼ 16
140
Formulas for Stress and Strain
[CHAP. 8
Combining Eqs. (8.2-3) and (8.2-5), the flexure stress on the top of the titanium is s¼
6ð1:285Þ 0:25ð0:06Þ2 ð11:37Þ
2þ
0:06 17 0:03 þ 0:03 28 0:06
" # 2 ð9:6 106 5:7 106 Þð50Þð17 106 Þ 0:03 0:03 28 0:06 3 þ2 11:37 0:06 0:06 17 0:03 ¼ 3242 þ 378 ¼ 3620 lb=in2 Likewise, the flexure stress on the bottom of the stainless steeel is s¼
6ð1:285Þ 0:03 28 0:06 þ 2 þ 0:25ð0:062 Þð11:37Þ 0:06 17 0:03 " 3 # 6 6 ð9:6 10 5:7 10 Þð50Þð28 106 Þ 0:03 17 0:03 þ 3 þ2 11:37 0:06 28 0:06
¼ 4365 þ 1644 ¼ 2720 lb=in2
8.3
Three-Moment Equation
The three-moment equation, which expresses the relationship between the bending moments found at three consecutive supports in a continuous beam, can be readily derived for any loading shown in Table 8.1. This is accomplished by taking any two consecutive spans and evaluating the slope for each span at the end where the two spans join. These slopes, which are expressed in terms of the three moments and the loads on the spans, are then equated and the equation reduced to its usual form. EXAMPLE Consider two contiguous spans loaded as shown in Fig. 8.6. In addition to the loading shown, it is known that the left end of span 1 had settled an amount y2 y1 relative to the right end of the span, and similarly that the left end of span 2 has settled an amount y3 y2 relative to the right end. (Note that y1 , y2 , and y3 are considered positive upward as usual.) The individual spans with their loadings are shown in Fig. 8.7(a,b). Determine the relationship between the applied loads and the moment at the intermediate support. Solution. Using cases 2e and 3e from Table 8.1 and noting the relative deflections mentioned above, the expression for the slope at the right end of
Figure 8.6
SEC.
8.4]
Beams; Flexure of Straight Bars
141
Figure 8.7
span 1 is y2 ¼
w1 ðl21 a21 Þ2 w1 ðl1 a1 Þ2 2 ð8l1 þ 9a1 l1 þ 3a21 Þ 24E1 I1 l1 360E1 I1 l1 M1 l21 M2 ðl21 3a21 Þ y2 y1 þ þ þ 6E1 I1 l1 6E1 I1 l1 l1
Similarly, using cases 1e and 3e from Table 8.1, the expression for the slope at the left end of span 2 is y2 ¼
W2 a2 M2 M3 y y2 ð2l a2 Þðl2 a2 Þ ð2l2 Þ ð2l2 6l22 þ 3l22 Þ þ 3 6E2 I2 l2 2 6E2 I2 l2 2 6E2 I2 l2 2 l2
Equating these slopes gives M1 l 1 M l M l M l w1 ðl1 a1 Þ2 2 þ 21 þ 22 þ 32 ¼ ð7l1 þ 21a1 l1 þ 12a21 Þ 6E1 I1 3E1 I1 3E2 I2 6E2 I2 360E1 I1 l1 y y1 W2 a2 y y2 2 ð2l a2 Þðl2 a2 Þ þ 3 l1 6E2 I2 l2 2 l2 If M1 and M3 are known, this expression can be solved for M2 : if not, similar expressions for the adjacent spans must be written and the set of equations solved for the moments.
The three-moment equation can also be applied to beams carrying axial tension or compression in addition to transverse loading. The procedure is exactly the same as that described above except the slope formulas to be used are those given in Tables 8.8 and 8.9.
8.4
Rigid Frames
By superposition and the matching of slopes and deflections, the formulas in Table 8.1 can be used to solve for the indeterminate reactions in rigid frames or to determine the deformations where the support conditions permit such deformations to take place. The term rigid in this section simply means that any deformations are small enough to have negligible effect on bending moments. In Table 8.2 formulas are given for the indeterminate reactions and end deformations for rigid frames consisting of three members. Only in-plane deformations and only those due to bending moments have
142
Formulas for Stress and Strain
[CHAP. 8
been included in the expressions found in this table. Since deformations due to transverse shear and axial loading are not included, the results are limited to those frames made up of members which are long in proportion to their depths (see assumptions 6 to 8 in Sec. 8.1). Each member must be straight and of uniform cross section having a principal axis lying in the plane of the frame. The elastic stability of the frame, either in the plane of the frame or out of this plane, has not been treated in developing Table 8.2. The effects of axial load on the bending deformations, as documented in Tables 8.7–8.9, have not been considered. A final check on a solution must verify that indeed these effects can be neglected. Very extensive compilations of formulas for rigid frames are available, notably those of Kleinlogel (Ref. 56) and Leontovich (Ref. 57). While Table 8.2 is obviously designed for frames with three members where the vertical members both lie on the same side of the horizontal member, its use is not limited to this configuration. One can set the lengths of either of the vertical members, members 1 and 2, equal to zero and solve for reactions and deformations of two-member frames. The length of the horizontal member, member 3, should not be set to zero for two reasons: (1) It does not generally represent a real problem; and (2) the lengths of members 1 and 2 are assumed not to change, and this adds a restraint to member 3 that would force it to have zero slope if its length was very short. Another very useful application of the expressions in Table 8.2 is to apply them to frames where one of the two vertical members lies on the opposite side of the horizontal member. Instead of forming a U-shape in the side view, it forms a Z-shape. To do this one must change the signs of three variables associated with the reversed member: (1) the sign of the length of the reversed member, (2) the sign of the distance a which locates any load on the reversed member, and (3) the sign of the product EI of the reversed member. All the reactions and end-point deflections retain their directions as given in the figures in Table 8.2; that is, if member 1 is reversed and extends upward from the left end of member 3, HA now acts at the upper end of member 1 and is positive to the left as is dHA . Example 3 illustrates this application as well as showing how the results of using Tables 8.1 and 8.2 together can be used to determine the deformations anywhere in a given frame. When the number of members is large, as in a framed building, a relaxation method such as moment distribution might be used or a digital computer could be programmed to solve the large number of equations. In all rigid frames, corner or knee design is important; much information and experimental data relating to this problem are to be found in the reports published by the Fritz Engineering Laboratories of Lehigh University. The frames given in Table 8.2 are assumed to have rigid corners; however, corrections can be made easily once the
SEC.
8.4]
Beams; Flexure of Straight Bars
143
rigidity of a given corner design is known by making use of the concentrated angular displacement loading with the displacement positioned at the corner. This application is illustrated in Example 2. EXAMPLES 1. The frame shown in Fig. 8.8(a) is fixed at the lower end of the right-hand member and guided at the lower end of the left-hand member in such a way as to prevent any rotation of this end but permitting horizontal motion if any is produced by the loading. The configuration could represent the upper half of the frame shown in Fig. 8.8(b); for this frame the material properties and physical dimensions are given as l1 ¼ 40 in, l2 ¼ 20 in, l3 ¼ 15 in, E1 ¼ E2 ¼ E3 ¼ 30 106 lb=in2 , I1 ¼ 8 in4 , I2 ¼ 10 in4 , and I3 ¼ 4 in4 . In addition to the load P of 1000 lb, the frame has been subjected to a temperature rise of 50 F since it was assembled in a stress-free condition. The coefficient of expansion of the material used in all three portions is 0.0000065 in=in= F. Solution. An examination of Table 8.2 shows the required end or support conditions in case 7 with the loading cases f and q listed under case 5. For cases 5 to 12 the frame constants are evaluated as follows:
CHH ¼ ¼
l31 3E1 I1
þ
l31
403 403 ð40 20Þ3 ð402 Þð15Þ þ þ ðl1 l2 Þ 4 3ð8Þ 3ð10Þ þ ¼ 3E2 I2 E3 I3 30ð106 Þ 3
l21 l3
2666:7 þ 1866:7 þ 6000 ¼ 0:0003511 in=lb 30ð106 Þ
Similarly CHV ¼ CVH ¼ 0:0000675 in=lb CHM ¼ CMH ¼ 0:00001033 lb1 CVV ¼ 0:0000244 in=lb CVM ¼ CMV ¼ 0:00000194 lb1 CMM ¼ 0:000000359 ðlb-inÞ1
Figure 8.8
144
Formulas for Stress and Strain
[CHAP. 8
For case 7f a3 LFH ¼ W CHH aCHM þ 6E1 I1 ¼ 1000 0:0003511 12ð0:00001033Þ þ
123 6ð30 106 Þð8Þ
¼ 1000ð0:0003511 0:000124 þ 0:0000012Þ ¼ 0:2282 in Similarly LFV ¼ 0:0442 in
and LFM ¼ 0:00632 rad
For case 7q LFH ¼ ðT To Þg3 l3 ¼ 50ð0:0000065Þð15Þ ¼ 0:004875 in LFV ¼ 0:0065 in
and LFM ¼ 0 rad
For the combined loading LFH ¼ 0:2282 0:004875 ¼ 0:2233 in LFV ¼ 0:0507 in LFM ¼ 0:00632 in Now the left end force, moment, and displacement can be evaluated: LFV CMM LFM CVM 0:0507ð0:359 106 Þ 0:00632ð1:94 106 Þ ¼ 2 CVV CMM CVM ð24:4 106 Þð0:359 106 Þ ð1:94 106 Þ2 ¼ 1189 lb
VA ¼
MA ¼ 11;179 lb-in dHA 0:0274 in Figure 8.9 shows the moment diagram for the entire frame.
Figure 8.9
(units are in lb-in)
2. If the joint at the top of the left vertical member in Example 1 had not been rigid but instead had been found to be deformable by 107 rad for every inchpound of bending moment applied to it, the solution can be modified as follows. Solution. The bending moment as the corner in question would be given by MA 28ð1000Þ, and so the corner rotation would be 107 ðMA 28;000Þ rad in a direction opposite to that shown by yo in case 5a. Note that the position of yo is
SEC.
8.4]
Beams; Flexure of Straight Bars
145
at the corner, and so a would be 40 in. Therefore, the following load terms due to the corner deformation can be added to the previously determined load terms: LFH ¼ 107 ðMA 28;000Þð40Þ LFV ¼ 0 LFM ¼ 107 ðMA 28;000Þ Thus the resultant load terms become LFH ¼ 0:2233 4 106 MA þ 0:112 ¼ 0:3353 4 106 MA LFV ¼ 0:0507 in LFM ¼ 0:00632 107 MA þ 0:0028 ¼ 0:00912 107 MA Again, the left end force, moment and displacement are evaluated: 0:0507ð0:359 106 Þ ð0:00912 107 MA Þð1:94 106 Þ 4:996 1012 ¼ 100 þ 0:0388MA
VA ¼
ð0:00912 107 MA Þð24:4 106 Þ 0:0507ð1:94 106 Þ 4:996 1012 ¼ 24;800 0:488MA
MA ¼
or MA ¼ 16;670 lb-in dHA ¼ 0:0460 in VA ¼ 747 lb 3. Find the reactions and deformations at the four positions A to D in the pinned-end frame shown in Fig. 8.10. All lengths are given in millimeters, Mo ¼ 2000 N-mm, and all members are made of aluminum for which E ¼ 7ð104 ÞN=mm2 with a constant cross section for which I ¼ 100 mm4 . Solution. Case 1h of Table 8.2 covers this combination of loading and end supports, if, due to the upward reach of member 1, appropriate negative values are used. The need for negative values is described in the introduction to Sec.
Figure 8.10
146
Formulas for Stress and Strain
[CHAP. 8
8.4. Substitute the following material properties and physical dimensions into case 1h: l1 ¼ 100 mm, l2 ¼ 150 mm, l3 ¼ 75 mm, a ¼ ð100 40Þ ¼ 60 mm, E1 I1 ¼ 7ð106 Þ N-mm2 , and E2 I2 ¼ E3 I3 ¼ 7ð106 Þ N-mm2 . Using these data gives the frame and load constants as AHH ¼ 0:2708 in=lb;
AHM ¼ AMH ¼ 0:0008036 lb1
AMM ¼ 0:00001786 ðlb-inÞ1 ; LPH ¼ 0:0005464ð2000Þ ¼ 1:0928 in LPM ¼ 0:000009286ð2000Þ ¼ 0:01857 rad Using these frames and load terms in case 1, the pinned-end case, the reaction and deformations are found to be dHA ¼ 0
MA ¼ 0
HA ¼
LPH ¼ 4:0352 N AHH
ðto leftÞ
and cA ¼ AMH HA LPM ¼ 0:01533 rad
ðclockwiseÞ
Applying the three independent statics equations to Fig. 8.10(a) results in VA ¼ 13:214 N
HB ¼ 4:0358 N
and VB ¼ 13:214 N
Now treat each of the three members as separate bodies in equilibrium, and find the deformations as pinned-end beams using equations from Table 8.1 as appropriate. For member 1 as shown in Fig. 8.10(b): Using case 3e twice, once for each of the two moment loadings, gives 2000 ½2ð100Þ2 6ð60Þð100Þ þ 3ð60Þ2 6ð7 106 Þð100Þ 1596:4 þ ½2ð100Þ2 6ð100Þð100Þ þ 3ð100Þ2 6ð7 106 Þð100Þ ¼ 0:001325 rad 2000 1596:4 ½ð100Þ2 3ð60Þ2 ½ð100Þ2 3ð100Þ2 yC ¼ 6ð7 106 Þð100Þ 6ð7 106 Þð100Þ ¼ 0:007221 rad yA ¼
To obtain the angle cA ¼ 0:01533 rad at position A, member 1 must be given an additional rigid-body clockwise rotation of 0:01533 0:001325 ¼ 0:01401 rad. This rigid-body motion moves position C to the left a distance of 1.401 mm and makes the slope at position C equal to 0:007221 0:01401 ¼ 0:006784 rad (clockwise). For member 3 as shown in Fig. 8.10(c): Again use case 3e from Table 8.1 twice to get 1596:4 605:35 ½2ð75Þ2 0 þ 0 ½2ð75Þ2 6ð75Þð75Þ þ 3ð75Þ2 6ð7 106 Þð75Þ 6ð7 106 Þð75Þ ¼ 0:006782 rad 1596:4 605:35 ½ð75Þ2 0 þ ½ð75Þ2 3ð75Þ2 yD ¼ 6ð7 106 Þð75Þ 6ð7 106 Þð75Þ ¼ 0:005013 rad yC ¼
SEC.
8.5]
Beams; Flexure of Straight Bars
147
No rigid-body rotation is necessary for member 3 since the left end has the same slope as the lower end of member 1, which is as it should be. For member 2 as shown in Fig. 8.10(d): Use case 3e from Table 8.1 to get
yD ¼
605:35 ½2ð150Þ2 0 þ 0 ¼ 0:004324 rad 6ð7 106 Þð150Þ
yB ¼
605:35 ½ð150Þ2 0 ¼ 0:002162 rad 6ð7 106 Þð150Þ
To match the slope at the right end of member 3, a rigid-body counterclockwise rotation of 0:005013 þ 0:00432 ¼ 0:009337 rad must be given to member 2. This creates a slope cB ¼ 0:009337 þ 0:002162 ¼ 0:01150 rad counterclockwise and a horizontal deflection at the top end of 0.009337(150) ¼ 1.401 mm to the left. This matches the horizontal deflection of the lower end of member 1 as a final check on the calculations. To verify that the effect of axial load on the bending deformations of the members is negligible, the Euler load on the longest member is found to be more than 100 times the actual load. Using the formulas from Table 8.8 would not produce significantly different results from those in Table 8.1.
8.5
Beams on Elastic Foundations
There are cases in which beams are supported on foundations which develop essentially continuous reactions that are proportional at each position along the beam to the deflection of the beam at that position. This is the reason for the name elastic foundation. Solutions are available (Refs. 41 and 42) which consider that the foundation transmits shear forces within the foundation such that the reaction force is not directly proportional to the deflection at a given location but instead is proportional to a function of the deflections near the given location; these solutions are much more difficult to use and are not justified in many cases since the linearity of most foundations is open to question anyway. It is not necessary, in fact, that a foundation be continuous. If a discontinuous foundation, such as is encountered in the support provided a rail by the cross ties, is found to have at least three concentrated reaction forces in every half-wavelength of the deflected beam, then the solutions provided in this section are adequate. Table 8.5 provides formulas for the reactions and deflections at the left end of a finite-length beam on an elastic foundation as well as formulas for the shear, moment, slope, and deflection at any point x along the length. The format used in presenting the formulas is designed to facilitate programming for use on a digital computer or programmable calculator.
148
Formulas for Stress and Strain
[CHAP. 8
In theory the equations in Table 8.5 are correct for any finite-length beam or for any finite foundation modulus, but for practical purposes they should not be used when bl exceeds a value of 6 because the roundoff errors that are created where two very nearly equal large numbers are subtracted will make the accuracy of the answer questionable. For this reason, Table 8.6 has been provided. Table 8.6 contains formulas for semi-infinite- and infinite-length beams on elastic foundations. These formulas are of a much simpler form since the far end of the beam is assumed to be far enough away so as to have no effect on the response of the left end to the loading. If bl > 6 and the load is nearer the left end, this is the case. Hete´ nyi (Ref. 53) discusses this problem of a beam supported on an elastic foundation extensively and shows how the solutions can be adapted to other elements such as hollow cylinders. Hete´ nyi (Ref. 51) has also developed a series solution for beams supported on elastic foundations in which the stiffness parameters of the beam and foundation are not incorporated in the arguments of trigonometric or hyperbolic functions. He gives tables of coefficients derived for specific boundary conditions from which deformation, moments, or shears can be found at any specific point along the beam. Any degree of accuracy can be obtained by using enough terms in the series. Tables of numerical values, Tables 8.3 and 8.4 are provided to assist in the solution of the formulas in Table 8.5. Interpolation is possible for values that are included but should be used with caution if it is noted that differences of large and nearly equal numbers are being encountered. A far better method of interpolation for a beam with a single load is to solve the problem twice. For the first solution move the load to the left until bðl aÞ is a value found in Table 8.3, and for the second solution move the load similarly to the right. A linear interpolation from these solutions should be very accurate. Presenting the formulas for end reactions and displacements in Table 8.5 in terms of the constants Ci and Cai is advantageous since it permits one to solve directly for loads anywhere on the span. If the loads are at the left end such that Ci ¼ Cai , then the formulas can be presented in a simpler form as is done in Ref. 6 of Chap. 13 for cylindrical shells. To facilitate the use of Table 8.5 when a concentrated load, moment, angular rotation, or lateral displacement is at the left end (that is, a ¼ 0), the following equations are presented to simplify the numerators: C1 C2 þ C3 C4 ¼ C12 ;
2C12 þ C2 C4 ¼ 2 þ C11
C2 C3 C1 C4 ¼ C13 ;
C22 2C1 C3 ¼ C14
C12 þ C32 ¼ 1 þ C11 ;
2C32 C2 C4 ¼ C11
C22 þ C42 ¼ 2C14 ;
2C1 C3 þ C42 ¼ C14
8.5]
SEC.
Beams; Flexure of Straight Bars
149
EXAMPLES 1. A 6-in, 12.5-lb I-beam 20 ft long is used as a rail for an overhead crane and is in turn being supported every 2 ft of its length by being bolted to the bottom of a 5-in, 10-lb I-beam at midlength. The supporting beams are each 21.5 ft long and are considered to be simply supported at the ends. This is a case of a discontinuous foundation being analyzed as a continuous foundation. It is desired to determine the maximum bending stresses in the 6-in beam as well as in the supporting beams when a load of 1 ton is supported at one end of the crane. Solution. The spring constant for each supporting beam is 48EI=l3 , or ð48Þð30 106 Þð12:1Þ=ð21:5 12Þ3 ¼ 1013 lb=in. If this is assumed to be distributed over a 2-ft length of the rail, the equivalent value of bo ko is 1.013=24 ¼ 42.2 lb=in per inch of deflection. Therefore
b¼
1=4 1=4 bo ko 42:2 ¼ ¼ 0:01127 in1 4ð30 106 Þð21:8Þ 4EI
and bl ¼ ð0:01127Þð240Þ ¼ 2:70
An examination of the deflection of a beam on an elastic foundation shows that it varies cyclicly in amplitude with the sine and cosine of bx. A half-wavelength of this cyclic variation would occur over a span l1 , where bl1 ¼ p, or l1 ¼ p= 0:01127 ¼ 279 in. There is no question about there being at least three supporting forces over this length, and so the use of the solution for a continuous foundation is entirely adequate. Since bl is less than 6, Table 8.5 will be used. Refer to case 1 where both ends are free. It must be pointed out that a simple support refers to a reaction force, developed by a support other than the foundation, which is large enough to prevent any vertical deflection of the end of the beam. From the table we find that RA ¼ 0 and MA ¼ 0; and since the load is at the left end, a ¼ 0. When a ¼ 0, the Ca terms are equal to the C terms, and so the four terms C1 , C2 , C3 , and C4 are calculated:
C1 ¼ cosh bl cos bl ¼ 7:47ð0:904Þ ¼ 6:76 C2 ¼ cosh bl sin bl þ sinh bl cos bl ¼ 7:47ð0:427Þ þ 7:41ð0:904Þ ¼ 3:50
Similarly C3 ¼ 3:17, C4 ¼ 9:89, and C11 ¼ 54:7. (See Tables 8.3 and 8.4.) Therefore,
yA ¼ yA ¼
2000 2ð30
106 Þð21:8Þð0:011272 Þ
ð3:502 Þ ð2Þð3:17Þð6:76Þ ¼ 0:01216 rad 54:7
2000 ð9:89Þð6:76Þ ð3:17Þð3:50Þ ¼ 1:092 in 2ð30 106 Þð21:8Þð0:011273 Þ 54:7
150
Formulas for Stress and Strain
[CHAP. 8
With the deformations at the left end known, the expression for the bending moment can be written: W F 2b a2 ¼ 1:092ð2Þð30 106 Þð21:8Þð0:011272 ÞF3 0:01216ð30 106 Þð21:8Þð0:01127ÞF4 2000 F 2ð0:01127Þ a2 ¼ 181;400F3 89;600F4 88;700Fa2
M ¼ yA 2EIb2 F3 yA EIbF4
Now substituting the expressions for Fa2, F3 , and F4 gives M ¼ 181;400 sinh bx sin bx 89;600ðcosh bx sin bx sinh bx cos bxÞ 88;700ðcosh bx sin bx þ sinh bx cos bxÞ or M ¼ 181;400 sinh bx sin bx 178;300 cosh bx sin bx þ 900 sinh bx cos bx The maximiun value of M can be found by trying values of x in the neighborhood of x ¼ p=4b ¼ p=4ð0:01127Þ ¼ 69:7 in, which would be the location of the maximum moment if the beam were infinitely long (see Table 8.6). This procedure reveals that the maximum moment occurs at x ¼ 66:5 in and has a value of 55;400 lb-in. The maximum stress in the 6-in I-beam is therefore 55,400(3)=21.8 ¼ 7620 lb=in2 . The maximum stress in the supporting 5-in I-beams is found at the midspan of the beam directly above the load. The deflection of this beam is known to be 1.092 in, and the spring constant is 1013 lb=in, so that the center load on the beam is 1.092(1013) ¼ 1107 lb. Therefore the maximum bending moment is Pl=4 ¼ 1107ð21:5Þð12Þ=4 ¼ 71;400 lb-in and the maximum stress is 71,400(2.5)=12.1 ¼ 14;780 lb=in2 . 2. If the 6-in I-beam in Example 1 had been much longer but supported in the same manner, Table 8.6 could have been used. Case 8 reveals that for an end load the end deflection is W =2EIb3 ¼ 2000=2ð30 106 Þð21:8Þð0:011273 Þ ¼ 1:070 in and the maximum moment would have equaled 0:3225W = b ¼ 0:3225ð2000Þ=0:01127 ¼ 57;200 in-lb at 69.7 in from the left end. We should not construe from this example that increasing the length will always increase the stresses; if the load had been placed elsewhere on the span, the longer beam could have had the lower maximum stress. 3. An aluminum alloy beam 3 in wide, 2 in deep, and 60 in long is manufactured with an initial concentrated angular deformation of 0.02 rad at midlength; this initial shape is shown in Fig. 8.11(a). In use, the beam is placed on an elastic foundation which develops 500 lb=in2 vertical upward pressure for every 1 in it is depressed. The beam is loaded by two concentrated loads of 4000 lb each and a uniformly distributed load of 80 lb=in over the portion between the concentrated loads. The loading is shown in Fig. 8.11(b). It is desired to determine the maximum bending stress in the aluminum beam.
SEC.
8.5]
Beams; Flexure of Straight Bars
151
Figure 8.11
Solution. First determine the beam and foundation parameters: 1 ð3Þð23 Þ ¼ 2 in4 ; k0 ¼ 500 lb=in2 =in; E ¼ 9:5 106 lb=in2 ; I ¼ 12 1=4 3ð500Þ b¼ ¼ 0:0666; l ¼ 60 in; bl ¼ 4:0 4ð9:5 106 Þð2Þ
C1 ¼ 17:85;
C2 ¼ 38:50;
C3 ¼ 20:65;
C4 ¼ 2:83;
bo ¼ 3 in
C11 ¼ 744
An examination of Table 8.5 shows the loading conditions covered by the superposition of three cases in which both ends are free: case 1 used twice with W1 ¼ 4000 lb and a1 ¼ 15 in, and W2 ¼ 4000 lb and a2 ¼ 45 in; case 2 used twice with w3 ¼ 80 lb=in and a3 ¼ 15 in, and w4 ¼ 80 lb=in and a4 ¼ 45 in; case 5 used once with yo ¼ 0:02 and a ¼ 30 in. The loads and deformations at the left end are now evaulated by summing the values for the five different loads, which is done in the order in which the loads are mentioned. But before actually summing the end values, a set of constants involving the load positions must be determined for each case. For case 1, load 1: Ca1 ¼ cosh bð60 15Þ cos bð60 15Þ ¼ 10:068ð0:99Þ ¼ 9:967 Ca2 ¼ 8:497 For case 1, load 2: Ca1 ¼ 0:834;
Ca2 ¼ 1:933
For case 2, load 3: Ca2 ¼ 8:497;
Ca3 ¼ 1:414
For case 2, load 4: Ca2 ¼ 1:933;
Ca3 ¼ 0:989
Ca3 ¼ 3:298;
Ca4 ¼ 4:930
For case 5:
152
Formulas for Stress and Strain
[CHAP. 8
Therefore RA ¼ 0 and MA ¼ 0. 4000 ð38:50Þð8:497Þ ð2Þð20:65Þð9:967Þ 744 2EIb2 4000 ð38:50Þð1:933Þ ð2Þð20:65Þð0:834Þ þ 744 2EIb2 80 ð38:50Þð1:414Þ ð20:65Þð8:497Þ þ 744 2EIb3 80 ð38:50Þð0:989Þ ð20:65Þð1:933Þ þ 744 2EIb3 ð38:50Þð4:93Þ ð2Þð20:65Þð3:298Þ þ 0:02 744 400 4000 80 ð0:0568Þ þ ð0:02688Þ þ ð0:1545Þ ¼ 2 2 EIb EIb EIb3 80 ð0:00125Þ þ 0:02ð0:0721Þ EIb3 ¼ 0:007582 rad
yA ¼
Similarly, yA ¼ 0:01172 in An examination of the equation for the transverse shear V shows that the value of the shear passes through zero at x ¼ 15, 30, and 45 in. The maximum positive bending moment occurs at x ¼ 15 in and is evaluated as follows, noting again that RA and MA are zero: M15 ¼ ð0:01172Þð2Þð9:5 106 Þð2Þð0:066662 Þ½sinhð0:06666Þð15Þ sin 1 ð0:007582Þð9:5 106 Þð2Þð0:06666Þðcosh 1 sin 1 sinh 1 cos 1Þ ¼ 8330 lb-in Similarly, the maximum negative moment at x ¼ 30 in is evaluated, making sure that the terms for the concentrated load at 15 in and the uniformly distributed load from 15 to 30 in are included: M30 ¼ 13;000 lb-in The maximum bending stress is given by s ¼ Mc=I and is found to be 6500 lb=in2 .
8.6
Deformation Due to the Elasticity of Fixed Supports
The formulas in Tables 8.1, 8.2, 8.5, 8.6, and 8.8–8.10 that apply to those cases where fixed or guided end supports are specified are based on the assumption that the support is rigid and holds the fixed or guided end truly horizontal or vertical. The slight deformation that actually occurs at the support permits the beam to assume there a
SEC.
8.7]
Beams; Flexure of Straight Bars
153
Figure 8.12
slope Dy, which for the conditions represented in Fig. 8.12, that is, a beam integral with a semi-infinite supporting foundation, is given by Dy ¼
16:67M ð1 nÞV þ Eh1 pEh21
Here M is the bending moment per unit width and V is the shear force per unit width of the beam at the support; E is the modulus of elasticity, and n is Poisson’s ratio for the foundation material; and h1 ¼ h þ 1:5r (Ref. 54). The effect of this deformation is to increase the deflections of the beam. For a cantilever, this increase is simply x Dy, but for other support conditions the concept of the externally created angular deformation may be utilized (see Example 2 on page 144). For the effect of many moment-loaded cantilever beams spaced closely one above the next, see Ref. 67. 8.7
Beams under Simultaneous Axial and Transverse Loading
Under certain conditions a beam may be subjected to axial tension or compression in addition to the transverse loads. Axial tension tends to straighten the beam and thus reduce the bending moments produced by the transve:rse loads, but axial compression has the opposite effect and may greatly increase the maximum bending moment and deflection and obviously must be less than the critical or buckling load. See Chap. 15. In either case a solution cannot be effected by simple superposition but must be arrived at by methods that take into account the change in deflection produced by the axial load. For any condition of loading, the maximum normal stress in an extreme fiber is given by smax ¼
P Mc A I
ð8:7-1Þ
where P is the axial load (positive if tensile and negative if compressive), A is the cross-sectional area of the beam, I=c is the section modulus, and M is the maximum bending moment due to the combined effect of axial and transverse loads. (Use the plus sign if
154
Formulas for Stress and Strain
[CHAP. 8
M causes tension at the point in question and the minus sign if M causes compression.) It is the determination of M that offers difficulty. For some cases, especially if P is small or tensile, it is permissible to ignore the small additional moment caused by P and to take M equal to M 0 , the bending moment due to transverse loads only. Approximate formulas of the type (Ref. 33) ymax ¼
y0max ; 1 ay P 2 =EI Mmax
ymax ¼
y0max 1 ay P 2 =EI
0 Mmax ¼ 1 aM P 2 =EI
ð8:7-2Þ
have been used, but the values of ay , ay , and aM are different for each loading and each manner of supporting the beam. Instead of tabulating the values of a, which give answers with increasing error as P increases, Tables 8.7(a–d) gives values of the coefficient CP which can be used in the expressions yA ¼ CP y0A ;
yA ¼ CP y0A ;
MA ¼ Cp MA0 ;
etc:
(8.7-3)
where the primed values refer to the laterally loaded beam without the axial load and can be evaluated from expressions found in Table 8.1. For those cases listed where the reactions are statically indeterminate, the reaction coefficients given will enable the remaining reactions to be evaluated by applying the principles of static equilibrium. The given values of CP are exact, based on the assumption that deflections due to transverse shear are negligible. This same assumption was used in developing the equations for transverse shear, bending moment, slope, and deflection shown in Tables 8.8 and 8.9. Table 8.8 lists the general equations just mentioned as well as boundary values and selected maximum values for the case of axial compressive loading plus transverse loading. Since, in general, axial tension is a less critical condition, where deflections, slopes, and moments are usually reduced by the axial load, Table 8.9 is much more compact and gives only the general equations and the left-end boundary values. Although the principle of superposition does not apply to the problem considered here, this modification of the principle can be used: The moment (or deflection) for a combination of transverse loads can be found by adding the moments (or deflections) for each transverse load combined with the entire axial load. Thus a beam supported at the ends and subjected to a uniform load, a center load, and an axial compression would have a maximum bending moment (or deflection) given by the sum of the maximum moments (or deflections) for Table
SEC.
8.7]
Beams; Flexure of Straight Bars
155
8.8, cases 1e and 2e, the end load being included once for each transverse load. A problem closely related to the beam under combined axial and lateral loading occurs when the ends of a beam are axially restrained from motion along the axis of the beam (held) and a lateral load is applied. A solution is effected by equating the increase in length of the neutral surface of the beam Pl=AE toÐ the decrease in length due to the 1 curvature of the neutral surface 12 0 y2 dx [Eq. (8.1-14)]. In general, solving the resulting equation for P is difficult owing to the presence of the hyperbolic functions and the several powers of the load P in the equation. If the beam is long, slender, and heavily loaded, this will be necessary for good accuracy; but if the deflections are small, the deflection curve can be approximated with a sine or cosine curve, obtaining the results given in Table 8.10. The following examples will illustrate the use of the formulas in Tables 8.7–8.10. EXAMPLES 1. A 4-in, 7.7-lb steel I-beam 20 ft long is simply supported at both ends and simultaneously subjected to a transverse load of 50 lb=ft (including its own weight), a concentrated lateral load of 600 lb acting vertically downward at a position 8 ft from the left end, and an axial compression of 3000 lb. It is required to determine the maximum fiber stress and the deflection at midlength. Solution. Here P ¼ 3000 lb; l ¼ 240 in; I ¼ 6 in4 ; I=c ¼ 3 in3 ; A ¼ 2:21 in2 ; wa ¼ wl ¼ 50 ¼ffiffiffiffiffiffiffiffiffiffiffiffi 4:17 lb=in; and a ¼ 0 for case 2e; W ¼ 600 lb and a ¼ 96 in for 12 p case 1e; k ¼ P=EI ¼ 0:00408 in1 ; kl ¼ 0:98. The solution will be carried out (a) ignoring deflection, (b) using coefficients from Table 8.7 and (c) using precise formulas from Table 8.8. (a) RA ¼ 860 lb, and max M80 ¼ 860ð8Þ 8ð50Þð4Þ ¼ 5280 lb-ft: max compressive stress ¼
P M 3000 5280ð12Þ ¼ ¼ 22;475 lb=in2 A I=c 2:21 3
For the uniform load (Table 8.1, case 2e): yl=2 ¼
5 wa l4 5ð4:17Þð2404 Þ ¼ ¼ 1:00 in 384 EI 384ð30 106 Þð6Þ
For the concentrated load (Table 8.1, case 1e): RA ¼ 360 lb 600ð96Þ½2ð240Þ 96ð240 96Þ yA ¼ ¼ 0:123 rad 6ð30 106 Þð6Þð240Þ yl=2 ¼ 0:123ð120Þ þ
360ð1203 Þ 600ð120 96Þ3 ¼ 0:907 in 6 6ð30 106 Þð6Þ 6ð30 10 Þð6Þ
Thus Total midlength deflection ¼ 1:907 in
156
Formulas for Stress and Strain
[CHAP. 8
(b) From Table 8.7(b) (simply supported ends), coefficients are given for concentrated loads at l=4 and l=2. Plotting curves of the coefficients versus kl and using linear interpolation to correct for a ¼ 0:4l give a value of CP ¼ 1:112 for the midlength deflection and 1.083 for the moment under the load. Similarly, for a uniform load on the entire span ða ¼ 0Þ, the values of CP are found to be 1.111 for the midlength deflection and 1.115 for the moment at midlength. If it is assumed that this last coefficient is also satisfactory for the moment at x ¼ 0:4l, the following deflections and moments are calculated: Max M80 ¼ 360ð8Þð1:083Þ þ ½500ð8Þ 8ð50Þð4Þð1:115Þ ¼ 3120 þ 2680 ¼ 5800 lb-ft P M 3000 5800ð12Þ ¼ ¼ 24;560 lb=in2 Max compressive stress ¼ A I=c 2:21 3 Midlength deflection ¼ 0:907ð1:112Þ 1:00ð1:111Þ ¼ 2:12 in (c) From Table 8.8 cases 1e and 2e, RA ¼ 860 lb and 600 sin 0:00408ð240 96Þ 240 96 yA ¼ 3000 sin 0:98 240 4:17 0:98 0:98 tan þ 0:00408ð3000Þ 2 2 600 0:5547 0:6 0:341ð0:533 0:49Þ ¼ 3000 0:8305 ¼ 0:0283 rad 860 0:0283ð3000Þ Max M80 ¼ sin 0:00408ð96Þ sin 0:392 0:00408 0:00408 4:17 ð1 cos 0:392Þ 0:004082 ¼ 80;500 þ 7950 19;000 ¼ 69;450 lb-in 3000 69;450 ¼ 24; 500 lb=in2 Max compressive stress ¼ 2:21 3 0:0283 860 sin 0:49 þ ð0:49 sin 0:49Þ Midlength deflection ¼ 0:00408 0:00408ð3000Þ 600 ½0:00408ð120 96Þ 0:00408ð3000Þ sin 0:00408ð120 96Þ 4:17 0:004082 ð1202 Þ 2 0:00408 ð3000Þ 2 1 þ cos 0:00408ð120Þ ¼ 3:27 þ 1:36 0:00785 0:192 ¼ 2:11 in The ease with which the coefficients CP can be obtained from Tables 8.7(a–d) makes this a very desirable way to solve problems of axially loaded beams. Some caution must be observed, however, when interpolating for the position of the load. For example, the concentrated moment in Tables 8.7c and 8.7d shows a large variation in CP for the end moments when the load position is changed from 0.25 to 0.50, especially under axial tension. Note that there are some cases in which CP either changes sign or increases and then decreases when kl is increased; in these cases the loading produces both positive and negative moments and deflections in the span.
SEC.
8.7]
Beams; Flexure of Straight Bars
157
2. A solid round brass bar 1 cm in diameter and 120 cm long is rigidly fixed at both ends by supports assumed to be sufficiently rigid to preclude any relative horizontal motion of the two supports. If this bar is subjected to a transverse center load of 300 N at midlength, what is the center deflection and what is the maximum tensile stress in the bar? Solution. Here P is an unknown tensile load; W ¼ 300 N and a ¼ 60 cm; l ¼ 120 cm; A ¼ 0:785 cm2 , I ¼ 0:0491 cm4 ; and E ¼ 10 106 N=cm2 . (This situation is described in Table 8.10, case 2.) The first equation is solved for ymax : ymax þ
0:785 300ð1203 Þ y3max ¼ 16ð0:0491Þ 2ðp4 Þð10 106 Þð0:0491Þ ymax þ y3max ¼ 5:44
Therefore ymax ¼ 1:57 cm. The second equation is now solved for P: p2 ð10 106 Þð0:785Þ 1:572 ¼ 3315 N 4ð1202 Þ rffiffiffiffiffiffi 1=2 P 3315 ¼ ¼ 0:0822 cm1 k¼ EI ð10 106 Þð0:0491Þ
P¼
kl ¼ 9:86 From Table 8.7, case 1d, the values of RA and MA can be calculated. (Note that yA and yA are zero.) First evaluate the necessary constants: C2 ¼ sinh 9:86 ¼ 9574:4 C3 ¼ cosh 9:86 1 ¼ 9574:4 1 ¼ 9573:4 C4 ¼ sinh 9:86 9:86 ¼ 9564:5 Ca3 ¼ cosh
9:86 1 ¼ 69:193 1 ¼ 68:193 2
Ca4 ¼ sinh 4:93 4:93 ¼ 69:186 4:93 ¼ 64:256 RA ¼ W
C3 Ca3 C2 Ca4 9573:4ð68:193Þ 9574:4ð64:256Þ ¼ 300 ¼ 300ð0:5Þ 9573:42 9574:4ð9564:5Þ C32 C2 C4
¼ 150 N W C4 Ca3 C3 Ca4 300 9564:5ð68:193Þ 9573:4ð64:256Þ ¼ MA ¼ k 0:0822 74;900 C32 C2 C4 300 ¼ 0:493 ¼ 1800 N-cm 0:0822 P Mc 3315 1800ð0:5Þ þ ¼ þ ¼ 4220 þ 18;330 A I 0:785 0:0491 ¼ 22;550 N=cm2
Max tensile stress ¼
1800 9:86 150 Midlength deflection ¼ cosh 1 þ ðsinh 4:93 4:93Þ 3315 2 3315ð0:0822Þ ¼ 37:0 þ 35:4 ¼ 1:6 cm
158
Formulas for Stress and Strain
[CHAP. 8
This compares favorably with the value ymax ¼ 1:57 cm obtained from the equation which was based on the assumption of a cosine curve for the deflection. An alternative to working with the large numerical values of the hyperbolic sines and cosines as shown in the preceding calculations would be to simplify the equations for this case where the load is at the center by using the doubleangle identities for hyperbolic functions. If this is done here, the expressions simplify to W W kl W kl kl RA ¼ MA ¼ tanh yl=2 ¼ tanh 2 k 4 kP 4 4 Using these expressions gives RA ¼ 150 N, MA ¼ 1800 N-cm and yl=2 ¼ 1:63 cm. Table 8.6 for axial compression gives the formulas for these special cases, but when the lateral loads are not placed at midlength or any of the other common locations, a desk calculator or digital computer must be used. If tables of hyperbolic functions are employed, it should be kept in mind that adequate solutions can be made using values of kl close to the desired values if such values are given in the table and the desired ones are not. For example, if the values for the arguments 9.86 and 4.93 are not available but values for 10 and 5 are (note that it is necessary to maintain the correct ratio a=l ), these values could be used with no noticeable change in the results. Finally, an energy approach, using Rayleigh’s technique, is outlined in Chap. 6, Sec. 13, of Ref. 72. The method works well with simple, axially constrained, and unconstrained beams.
8.8
Beams of Variable Section
Stress. For a beam whose cross section changes gradually, Eqs.
(8.1-1), (8.1-4), and (8.1-10)–(8.1-12) (Sec. 8.1) apply with sufficient accuracy; Eqs. (8.1-3) and (8.1-5)–(8.1-7) apply if I is treated as a variable, as in the examples that follow. All the formulas given in Table 8.1 for vertical shear and bending moments in statically determinate beams apply, but the formulas given for statically indeterminate beams and for deflection and slope are inapplicable to beams of nonuniform section unless the section varies in such a way that I is constant. Accurate analysis (Ref. 3) shows that in an end-loaded cantilever beam of rectangular section which is symmetrically tapered in the plane of bending the maximum fiber stress is somewhat less than is indicated by Eq. (8.1-12) the error amounting to about 5% for a surface slope of 15 (wedge angle 30 ) and about 10% for a surface slope of 20 . See also Prob. 2.35 in Ref. 66. The maximum horizontal and vertical shear stress is shown to occur at the upper and lower surfaces instead of at the neutral axis and to be approximately three times as great as the average shear stress on the section for slopes up to 20 . It is very doubtful, however, if this shear stress is often critical even in wood beams, although it may possibly start failure in short, heavily reinforced concrete beams that are deepened or ‘‘haunched’’ at the ends.
SEC.
8.8]
Beams; Flexure of Straight Bars
159
Such a failure, if observed, would probably be ascribed to compression since it would occur at a point of high compressive stress. It is also conceivable, of course, that this shear stress might be of importance in certain metal parts subject to repeated stress. Abrupt changes in the section of a beam cause high local stresses, the effect of which is taken into account by using the proper factor of stress concentration (Sec. 3.10 and Table 17.1). Deflection. Determining deflections or statically indeterminate reactions for beams of variable section can be considered in two categories: where the beam has a continuously varying cross section from one end to the other, and where the cross section varies in a stepwise fashion. Considering the first category, where the section varies continuously, we sometimes find a variation where Eq. (8.1-5) can be integrated directly, with the moment of inertia treated as a variable. This has been accomplished in Ref. 20 for tapered beams of circular section, but using the expressions presented, one must carry more than the usual number of digits to get accurate results. In most instances, however, this is not easy, if possible, and a more productive approach is to integrate Eq. (8.1-6) numerically using small incremental lengths Dx. This has been done for a limited number of cases, and the results are tabulated in Tables 8.11(a)–(d). These tables give coefficients by which the stated reaction forces or moments or the stated deformations for uniform beams, as given in Table 8.1, must be multiplied to obtain the comparable reactions or deformations for the tapered beams. The coefficients are dependent upon the ratio of the moment of inertia at the right end of the beam IB to the moment of inertia at the left end IA , assuming that the uniform beam has a moment of inertia IA . The coefficients are also dependent upon the manner of variation between the two end values. This variation is of the form Ix ¼ IA ð1 þ Kx=lÞn , where x is measured from the left end and K ¼ ðIB =IA Þ1=n 1. Thus if the beam is uniform, n ¼ 0; if the width of a rectangular cross section varies linearly, n ¼ 1; if the width of a rectangular cross section varies parabolically, n ¼ 2; if the depth of a rectangular cross section varies linearly, n ¼ 3; and if the lateral dimensions of any cross section vary linearly and proportionately, n ¼ 4. Beams having similar variations in cross section can be analysed approximately by comparing the given variations to those found in Table 8.11. Coefficients are given for only a few values of a=l, so it is not desirable to interpolate to determine coefficients for other values of a=l. Instead it is advisable to determine the corrected deformations or reactions with the loads at the tabulated values of a=l and then interpolate. This allows the use of additional known values as shown in the second example below. For beams with symmetric end condi-
160
Formulas for Stress and Strain
[CHAP. 8
tions, such as both ends fixed or both ends simply supported, the data given for any value of a=l < 0:5 can be used twice by reversing the beam end for end. EXAMPLES 1. A tapered beam 30 in long with a depth varying linearly from 2 in at the left end to 4 in at the right end and with a constant width of 1.5 in is fixed on the right end and simply supported on the left end. A concentrated clockwise couple of 5000 lb-in is applied at midlength and it is desired to know the maximum bending stress in the beam. Solution. First determine the left-end reaction force for a uniform cross section. From Table 8.1, case 3c, the left reaction is
RA ¼
3Mo ðl2 a2 Þ 3ð5000Þð302 152 Þ ¼ 187:5 lb ¼ 2l3 2ð303 Þ
For the tapered beam
IA ¼
1:5ð23 Þ ¼ 1 in4 ; 12
IB ¼
1:5ð43 Þ ¼ 8 in4 12
In Table 8.11(c) for n ¼ 3, IB =IA ¼ 8; and for case 3c with the loading at l=2, the coefficient is listed as 0.906. Therefore, the left-end reaction is 187:5ð0:906Þ ¼ 170 lb The maximum negative moment will occur just left of midlength and will equal 170ð15Þ ¼ 2550 lb-in. The maximum positive moment will occur just right of midlength and will equal 2550 þ 5000 ¼ 2450 lb-in. At midlength the moment of inertia I ¼ 1:5ð33 Þ=12 ¼ 3:37 in4 , and so the maximum stress is given by s ¼ Mc=I ¼ 2550ð1:5Þ=3:37 ¼ 1135 lb=in2 just left of midlength. 2. A machine part is an 800-mm-long straight beam with a variable wideflange cross section. The single central web has a constant thickness of 1.5 mm but a linearly varying depth from 6 mm at the left end A to 10 mm at the right end B. The web and flanges are welded together continuously over the entire length and are also welded to supporting structures at each end to provide fixed ends. A concentrated lateral load of 100 N acts normal to the central axis of the beam parallel to the web at a distance of 300 mm from the left end. The maximum bending stress and the deflection under the load are desired. The modulus of elasticity is 70 GPa, or 70,000 N=mm2 . Solution. First determine the left-end reaction force and moment for a beam of constant cross section. From Table 8.1, case 1d,
RA ¼
W 100 ðl aÞ2 ðl þ 2aÞ ¼ ð800 300Þ2 ð800 þ 600Þ ¼ 68:36 N l3 8003
MA ¼
Wa 100ð300Þ ðl aÞ2 ¼ ð800 300Þ2 ¼ 11;720 N-mm l2 8002
SEC.
8.8]
Beams; Flexure of Straight Bars
161
For the tapered beam, 4ð103 Þ 2:5ð63 Þ ¼ 288:3 mm4 12 8ð143 Þ 6:5ð103 Þ ¼ 1287:7 mm4 IB ¼ 12 IA ¼
and at midlength where x ¼ l=2, the moment of inertia is given by Il=2 ¼
6ð123 Þ 4:5ð83 Þ ¼ 672:0 mm4 12
Using the formula for the variation of I with x and these three values for the moment of inertia, approximate values for K and n can be found. n K Il=2 ¼ IA 1 þ IB ¼ IA ð1 þ K Þn ; 2 n 1287:7 672 K ¼ 4:466 ¼ ð1 þ K Þn ; ¼ 2:331 ¼ 1 þ 288:3 288:3 2 4:4661=n 2ð2:331Þ1=n þ 1 ¼ 0 Solving this last expression gives 1=n ¼ 0:35, n ¼ 2:86, and K ¼ 0:689. An examination of Tables 8.11(a–d) shows that for a fixed-ended beam with a concentrated load, which is case 1d in Table 8.1, values of coefficients are given only for a=l ¼ 0:25 and 0.50. For this problem a=l ¼ 0:375. Simple linear interpolation is not sufficiently accurate. However, if one imagines the load at a=l ¼ 0:25 the values for RA and MA can be found. This procedure can be repeated for a=l ¼ 0:50. Two other sets of data are also available. If the load were placed at the left end, a=l ¼ 0, MA ¼ 0, RA ¼ 100 N, and dMA =da ¼ 100 N. If the load were placed at the right end, a=l ¼ 1, RA ¼ 0, MA ¼ 0, and dMA =da ¼ 0. The variations of the tabulated coefficients with IB =IA and with n do not pose a comparable problem since many data are available. Plotting curves for the variation with IB =IA and interpolating linearly between n ¼ 2 and n ¼ 3 for n ¼ 2:86 give the coefficients used below to find the values for RA and MA at a=l ¼ 0:25 and 0.50: Untapered beam a=l
0.25
0.50
RA (N) MA (N-mm)
84.38 11;250
50.00 10;000
Tapered beam where n ¼ 2:86 and IB =IA ¼ 4:466 0.25
0.50
84.38(0.922) ¼ 77.80 11;250ð0:788Þ ¼ 8865
50(0.0805) ¼ 40.25 10;000ð0:648Þ ¼ 6480
Plotting these values of RA and MA versus a=l for the four positions allows one to pick from the graphs at a=l ¼ 0:375, RA ¼ 60 N, and MA ¼ 8800 N-mm. The use of static equilibrium now gives MB ¼ 10;800 N-mm and the moment at the load of 9200 N-mm. The bending stress at the left end is found to be the largest. sA ¼
MA cA 8800ð5Þ ¼ 152:6 MPa ¼ 288:3 IA
162
Formulas for Stress and Strain
[CHAP. 8
No correction coefficients for deflections are included for case ld in Table 8.11. The deflection at the load position can be found from the information in this table, however, if either end of the beam is isolated and treated as a cantilever with an end load and an end moment. The moment of inertia at the load position C is given by IC ¼
5:5ð11:53 Þ 4ð7:53 Þ ¼ 556:4 mm4 12
Treat the left portion of the beam as a 300-mm-long cantilever, using case 1a with an end load of 60 N and case 3a with an end moment of 9200 N-mm. Determine the correction coefficients for a=l ¼ 0, n ¼ 3, and the moment of inertia ratio of 288.33=556.44 ¼ 0.518. Interpolation between data for n ¼ 2 and n ¼ 3 is not justified when considering the approximations already made from plotted curves. Noting that all correction coefficients in Table 8.11 are unity for IB =IA ¼ 1 and using data points for IB =IA ¼ 0:25 and 0.50, the correction coefficients used below were found yC ¼
60ð3003 Þð1:645Þ 9200ð3002 Þð1:560Þ þ ¼ 22:8 þ 16:6 ¼ 6:2 mm 3ð70;000Þð556:4Þ 2ð70;000Þð556:4Þ
This deflection at the load can be checked by repeating the above procedure by using the right-hand portion of the beam. The slope of the beam at the load can also be used as a check. Alternative solution. The solution just presented was intended to illustrate appropriate methods of interpolation with the limited load positions shown in the tables. There is also an alternative solution involving superposition of cases. Remove the fixity at end A and treat the 500-mm-long right portion as a cantilever with an end load of 100 N. Use n ¼ 3 as being close enough to n ¼ 2:86 and IB =IC ¼ 1287:7=556:4 ¼ 2:314. Interpolate between IB =IC ¼ 2 and 4 to obtain from case 1a in Table 8.11(c) the correction coefficients used below to calculate the slope and deflection at the load yC ¼
100ð5003 Þð0:555Þ ¼ 59:37 mm 3ð70;000Þð556:4Þ
yC ¼
100ð5002 Þð0:593Þ ¼ 0:1903 rad 2ð70;000Þð556:4Þ
Since the left portion is unloaded and remains straight, the end deflection and slope are yA ¼ 59:37 300ð0:1903Þ ¼ 116:5 mm, and yA ¼ 0:1903 rad. Next treat the complete beam as a cantilever under an end load RA and an end moment MA . Let IA ¼ 228:3 mm4 , IB =IA ¼ 4:466, and again let n ¼ 3. From cases 1a and 3a in Table 8.11(c), RA ð8003 Þð0:332Þ MA ð8002 Þð0:380Þ þ ¼ 2:808RA þ 0:00602MA 3ð70;000Þð288:3Þ 2ð70;000Þð288:3Þ R ð8002 Þð0:380Þ MA ð800Þð0:497Þ ¼ 0:006024RA 19:7ð106 ÞMA yA ¼ A 2ð70;000Þð288:3Þ ð70;000Þð288:3Þ
yA ¼
Adding the slopes and deflections from the load of 100 N to those above and equating each to zero to represent the fixed end gives RA ¼ 60:3 N and MA ¼ 8790 N-mm. This is a reasonable check on those values from the first solution.
SEC.
8.8]
Beams; Flexure of Straight Bars
163
The second category of determining deflections, where the cross section varies in steps from one uniform section to another, can be solved in several ways. Equation (8.1-5) can be integrated, matching slopes and deflections at the transition sections, or Eq. (8.1-6) can be integrated over the separate portions and summed to obtain the desired deflections. A third method utilizes the advantages of the step function and its application to beam deflections as given in Table 8.1. In a given portion of the span where the cross section is uniform it is apparent that the shape of the elastic curve will remain the same if the internal bending moments and the moments of inertia are increased or decreased in proportion. By this means, a modified moment diagram can be constructed which could be applied to a beam with a single constant cross section and thereby produce an elastic curve identical to the one produced by the actual moments and the several moments of inertia present in the actual span. It is also apparent that this modified moment diagram could be produced by adding appropriate loads to the beam. (See Refs. 29 and 65.) In summary, then, a new loading is constructed which will produce the required elastic curve, and the solution for this loading is carried out by using the formulas in Table 8.1. This procedure will be illustrated by the following example. EXAMPLE The beam shown in Fig. 8.13 has a constant depth of 4 in and a step increase in the width from 2 to 5 in at a point 5 ft from the left end. The left end is simply supported, and the right end is fixed; the loading is a uniform 200 lb=ft from x ¼ 3 ft to the right end. Find the value of the reaction at the left end and the maximum stress. Solution. For the left 5 ft, I1 ¼ 2ð43 Þ=12 ¼ 10:67 in4 . For the right 5 ft, I2 ¼ 5ð43 Þ=12 ¼ 26:67 in4 , or 2.5 times I1 . The same M =I diagram shown in Fig. 8.13(e) can be produced by the loading shown in Fig. 8.14 acting upon a beam having a constant moment of inertia I2 . Note that all loads on the left portion simply have been increased by a factor of 2.5, while added loads at the 5-ft position reduce the effects of these added loads to those previously present on the right portion. To find the left-end reaction for the beam loaded as shown in Fig. 7.14(a), use Table 8.1, case 1c, where W ¼ 1:5R1 600 and a ¼ 5; case 2c, where wa ¼ wl ¼ 500 lb=ft and a ¼ 3 ft; case 2c, again, where wa ¼ wl ¼ 300 lb=ft and a ¼ 5 ft; and finally case 3c, where Mo ¼ ð7:5R1 600Þ and a ¼ 5 ft. Summing the expressions for RA from these cases in the order above, we obtain RA ¼ 2:5R1 ¼ þ
ð1:5R1 600Þð10 5Þ2 500ð10 3Þ3 ½2ð10Þ þ 5 þ ½3ð10Þ þ 3 2ð103 Þ 8ð103 Þ
ð300Þð10 5Þ3 3½ð7:5R1 600Þ ½3ð10Þ þ 5 ð102 52 Þ 2ð103 Þ 8ð103 Þ
which gives R1 ¼ 244 lb.
164
Formulas for Stress and Strain
Figure 8.13
Figure 8.14
[CHAP. 8
SEC.
8.9]
Beams; Flexure of Straight Bars
165
From Fig. 8.13(a) we can observe that the maximum positive bending moment will occur at x ¼ 4:22 ft, where the transverse shear will be zero. The maximum moments are therefore 200 ð1:222 Þ ¼ 881 lb-ft 2 Max M ¼ 244ð10Þ 4900 ¼ 2460 lb-ft at the right end Max þ M ¼ 244ð4:22Þ
The maximum stresses are s ¼ 881ð12Þð2Þ=10:67 ¼ 1982 lb=in2 at x ¼ 4:22 ft and s ¼ 2460ð12Þð2Þ=26:67 ¼ 2215 lb=in2 at x ¼ 10 ft.
8.9
Slotted Beams
If the web of a beam is pierced by a hole or slot (Fig. 8.15), the stresses in the extreme fibers a and b at any section B are given by MA VA xI1 =ðI1 þ I2 Þ ðI=cÞ1 I=c MA VA xI2 =ðI1 þ I2 Þ þ sb ¼ ðI=cÞ2 I=c
sa ¼
ðcompressionÞ ðtensionÞ
Here MA is the bending moment at A (midlength of the slot), VA is the vertical shear at A, I=c is the section modulus of the net beam section at B, I1 and I2 are the moments of inertia, and ðI=cÞ, and ðI=cÞ2 are the section moduli of the cross sections of parts 1 and 2 about their own central axes. M and V are positive or negative according to the usual convention, and x is positive when measured to the right. The preceding formulas are derived by replacing all forces acting on the beam to the left of A by an equivalent couple MA and shear VA at A. The couple produces a bending stress given by the first term of the formula. The shear divides between parts 1 and 2 in proportion to their respective I’s and produces in each part an additional bending stress given by the second term of the formula. The stress at any other point in the cross section can be found similarly by adding the stresses due to MA and those due to this secondary bending caused by the shear. (At the ends of the slot there is a stress concentration at the corners which is not taken into account here.)
Figure 8.15
166
Formulas for Stress and Strain
[CHAP. 8
The above analysis applies also to a beam with multiple slots of equal length; all that is necessary is to modify the term ðI1 þ I2 Þ. The numerator is still the I of the part in question and the denominator is the sum of the I’s of all the parts 1, 2, 3, etc. The formulas can also be used for a rigid frame consisting of beams of equal length joined at their ends by rigid members; thus in Fig. 8.15 parts 1 and 2 might equally well be two separate beams joined at their ends by rigid crosspieces. 8.10
Beams of Relatively Great Depth
In beams of small span=depth ratio, the transverse shear stresses are likely to be high and the resulting deflection due to shear may not be negligible. For span=depth ratios of 3 or more, the deflection ys due to shear is found by the method of unit loads to be ð Vv dx ð8:10-1Þ ys ¼ F AG or by Castigliano’s theorem to be ys ¼
@Us @P
ð8:10-2Þ
In Eq. (8.10-1), V is the vertical shear due to the actual loads, v is the vertical shear due to a unit load acting at the section where the deflection is desired, A is the area of the section, G is the modulus of rigidity, F is a factor depending on the form of the cross section, and the integration extends over the entire length of the beam, with due regard to the signs of V and v. For three solid sections, a rectangle, a triangle with base either up or down, and a trapezoid with parallel sides top and bottom, F ¼ 65; for a diamond-shaped section, F ¼ 31 30; for a solid circular section, F ¼ 10 ; for a thin-walled hollow circular section, 9 F ¼ 2; for an I- or box section with flanges and webs of uniform thickness, 3ðD22 D21 ÞD1 t2 4D22 F ¼ 1þ 1 t1 10r2 2D32 where D1 ¼ distance from neutral axis to the nearest surface of the flange D2 ¼ distance from neutral axis to extreme fiber t1 ¼ thickness of web ðor webs in box beamsÞ t2 ¼ width of flange r ¼ radius of gyration of section with respect to the neutral axis
SEC.
8.10]
Beams; Flexure of Straight Bars
167
If the I- or box beam has flanges of nonuniform thickness, it may be replaced by an ‘‘equivalent’’ section whose flanges, of uniform thickness, have the same width and areas as those of the actual section (Ref. 19). Approximate results may be obtained for I-beams using F ¼ 1 and taking for A the area of the web. Application of Eq. (8.10-1) to several common cases of loading yields the following results: 1 Pl ys ¼ F 4 AG 1 wl2 End support; uniform load w ys ¼ F 8 AG Pl Cantilever; end load P ys ¼ F AG 1 wl2 Cantilever; uniform load w ys ¼ F 2 AG Ð 2 In Eq. (8.10-2), Us ¼ F ðV =2AGÞdx; P is a vertical load, real or imaginary, applied at the section where ys is to be found, and the other terms have the same meaning as in Eq. (8.10-1). The deflection due to shear will usually be negligible in metal beams unless the span=depth ratio is extremely small; in wood beams, because of the small value of G compared with E, deflection due to shear is much more important. In computing deflections it may be allowed for by using for E a value obtained from bending tests (shear deflection ignored) on beams of similar proportions or a value about 10% less than that found by testing in direct compression if the span=depth ratio is between 12 and 24. For larger ratios the effect of shear is negligible, and for lower ratios it should be calculated by the preceding method. For extremely short deep beams, the assumption of linear stress distribution, on which the simple theory of flexure is based, is no longer valid. Equation (8.1-1) gives sufficiently accurate results for span=depth ratios down to about 3; for still smaller ratios it was believed formerly that the actual stresses were smaller than the formula indicates (Refs. 1 and 2), but more recent analyses by numerical methods (Refs. 43 and 44) indicate that the contrary is true. These analyses show that at s=d between 1.5 and 1, depending on the manner of loading and support, the stress distribution changes radically and the ratio of maximum stress to Mc=I becomes greater than 1 and increases rapidly as s=d becomes still smaller. In the following table, the influence of s=d on both maximum fiber stress and maximum horizontal shear stress is shown in accordance with the solution given in Ref. 43. Reference 44 gives comparable results, and both strain-gage measurements (Ref. 45) and photoelastic studies (Ref. 46) support the conclusions reached in these analyses. End support; center load P
168
Formulas for Stress and Strain
[CHAP. 8
Uniform load over entire l
Uniform load over middle
1 12 l
Ratio l=d
Ratio span=d
max st Mc=I
max sc Mc=I
max t V =A
max st Mc=I
max sc Mc=I
max t V =A
3 2.5 2.0 1.5 1 0.5
2.875 2.395 1.915 1.4375 0.958 0.479 0.3193
1.025 1.046 1.116 1.401 2.725 10.95 24.70
1.030 1.035 1.022 0.879 0.600 2.365 5.160
1.58 1.60 1.64 1.80 2.43 4.53 6.05
0.970 0.960 0.962 1.038 1.513 5.460 12.35
1.655 1.965 2.525 3.585 6.140 15.73 25.55
1.57 1.60 1.70 1.92 2.39 3.78 7.23
1 3
These established facts concerning elastic stresses in short beams seem incompatible with the contrary influence of s=d on modulus of rupture, discussed in Sec. 8.15, unless it is assumed that there is a very radical redistribution of stress as soon as plastic action sets in. The stress produced by a concentrated load acting on a very short cantilever beam or projection (gear tooth, sawtooth, screw thread) can be found by the following formula, due to Heywood (Chap. 2, Ref. 28) and modified by Kelley and Pedersen (Ref. 59). As given here, the formula follows this modification, with some changes in notation. Figure 8.16 represents the profile of the beam, assumed to be of uniform thickness t. ED is the axis or center line of the beam; it bisects the angle between the sides if these are straight; otherwise it is drawn through the centers of two unequal inscribed circles. W represents the load; its line of action, or load line, intersects the beam profile at C and the beam axis at O. The inscribed parabola, with vertex at O, is tangent to the fillet on the tension side of the beam at A, which is the point of maximum tensile stress. (A can be located by making AF equal to FE by trial, F being the intersection of a perpendicular to the axis at O and a trial tangent to the fillet.) B is the corresponding point on the compression side, and D is the intersection of the beam axis with section AB. The dimensions a and e are perpendicular, respectively, to the load line and to the beam axis, r is the fillet radius, and b is the straight-line distance from A to C. The tensile stress at A is given by e0:7 1:5a cos b W 0:45 s¼ 1 þ 0:26 þ þ t r e2 2e ðbeÞ1=2
SEC.
8.11]
Beams; Flexure of Straight Bars
169
Figure 8.16
Here the quantity in the first pair of brackets is the factor of stress concentration for the fillet. In the second pair of brackets, the first term represents the bending moment divided by the section modulus, the second term represents the effect of the component of the load along the tangent line, positive when tensile, and the third term represents what Heywood calls the proximity effect, which may be regarded as an adjustment for the very small span=depth ratio. Kelley and Pedersen have suggested a further refinement in locating the point of maximum stress, putting it at an angular distance equal to 25 12 a, positive toward the root of the fillet. Heywood suggests locating this point at 30 from the outer end of the fillet, reducing this to 12 as the ratio of b to e increases; also, Heywood locates the moment of W about a point halfway between A and B instead of about D. For most cases the slightly different procedures seem to give comparable results and agree well with photoelastic analysis. However, more recent experimental studies (1963), including fatigue tests, indicate that actual stresses may considerably exceed those computed by the formula (Ref. 63).
8.11
Beams of Relatively Great Width
Because of prevention of the lateral deformation that would normally accompany the fiber stresses, wide beams, such as thin metallic strips, are more rigid than the formulas of Sec. 8.1 indicate. This stiffening effect is taken into account by using E=ð1 n2 Þ instead of E in the formulas for deflection and curvature if the beams are very wide (Ref. 21). The anticlastic curvature that exists on narrow rectangular beams is still present at the extreme edges of very wide beams, but the central region remains flat in a transverse direction and trans-
170
Formulas for Stress and Strain
[CHAP. 8
verse bending stresses equal to Poisson’s ratio times the longitudinal bending stresses are present. For rectangular beams of moderate width, Ashwell (Ref. 10) shows that the stiffness depends not only upon the ratio of depth to width of the beam but also upon the radius of curvature to which the beam is bent. For a rectangular beam of width b and depth h bent to a radius of curvature r by a bending moment M , these variables are related by the expression 1=r ¼ M =KEI , where I ¼ bh3 =12, and the following table of values for K is given for several values of Poisson’s ratio and for the quantity b2 =rh. b2 =rh Value of n 0.1000 0.2000 0.3000 0.3333 0.4000 0.5000
0.25
1.00
1.0000 1.0001 1.0002 1.0002 1.0003 1.0005
1.0003 1.0013 1.0029 1.0036 1.0052 1.0081
4.00
16.0
50.0
200.
800.
1.0033 1.0135 1.0311 1.0387 1.0569 1.0923
1.0073 1.0300 1.0710 1.0895 1.1357 1.2351
1.0085 1.0349 1.0826 1.1042 1.1584 1.2755
1.0093 1.0383 1.0907 1.1146 1.1744 1.3045
1.0097 1.0400 1.0948 1.1198 1.1825 1.3189
In very short wide beams, such as the concrete slabs used as highway-bridge flooring, the deflection and fiber-stress distribution cannot be regarded as uniform across the width. In calculating the strength of such a slab, it is convenient to make use of the concept of effective width, i.e., the width of a spanwise strip which, acting as a beam with uniform extreme fiber stress equal to the maximum stress in the slab, develops the same resisting moment as does the slab. The effective width depends on the manner of support, manner of loading, and ratio of breadth to span b=a. It has been determined by Holl (Ref. 22) for a number of assumed conditions, and the results are given in the following table for a slab that is freely supported at each of two opposite edges (Fig. 8.17). Two kinds of loading are considered, viz. uniform load over the entire slab and load uniformly distributed over a central circular area of radius c. The ratio of the effective width e to the span a is given for each of a number of ratios of c to slab thickness h and each of a number of b=a values. Values of e=a for Loading Uniform Central, c ¼ 0 Central, c ¼ 0:125h Central, c ¼ 0:250h Central, c ¼ 0:500h
b=a ¼ 1
b=a ¼ 1:2
b=a ¼ 1:6
b=a ¼ 2
b=a ¼ 1
0.960 0.568 0.581 0.599 0.652
1.145 0.599 0.614 0.634 0.694
1.519 0.633 0.649 0.672 0.740
1.900 0.648 0.665 0.689 0.761
0.656 0.673 0.697 0.770
SEC.
8.11]
Beams; Flexure of Straight Bars
171
Figure 8.17
For the same case (a slab that is supported at opposite edges and loaded on a central circular area) Westergaard (Ref. 23) gives e ¼ 0:58a þ 4c as an approximate expression for effective width. Morris (Ref. 24) gives e ¼ 12 ec þ d as an approximate expression for the effective width for midspan off-center loading, where ec is the effective width for central loading and d is the distance from the load to the nearer unsupported edge. For a slab that is fixed at two opposite edges and uniformly loaded, the stresses and deflections may be calculated with sufficient accuracy by the ordinary beam formulas, replacing E by E=ð1 n2 Þ. For a slab thus supported and loaded at the center, the maximum stresses occur under the load, except for relatively large values of c, where they occur at the midpoints of the fixed edges. The effective widths are approximately as given in the following table (values from the curves of Ref. 22). Here b=a and c have the same meaning as in the preceding table, but it should be noted that values of e=b are given instead of e=a. Values of e=b for Values of c
b=a ¼ 1
b=a ¼ 1:2
b=a ¼ 1:6
b=a ¼ 2:0
Max stress at
0 0:01a 0:03a 0:10a
0.51 0.52 0.58 0.69
0.52 0.54 0.59 0.73
0.53 0.55 0.60 0.81
0.53 0.55 0.60 0.86
Load Load Load Fixed edges
Holl (Ref. 22) discusses the deflections of a wide beam with two edges supported and the distribution of pressure under the supported edges. The problem of determining the effective width in concrete slabs and tests made for that purpose are discussed by Kelley (Ref. 25), who also gives a brief bibliography on the subject. The case of a very wide cantilever slab under a concentrated load is discussed by MacGregor (Ref. 26), Holl (Ref. 27), Jaramillo (Ref. 47), Wellauer and Seireg (Ref. 48), Little (Ref. 49), Small (Ref. 50), and others. For the conditions represented in Fig. 8.18, a cantilever plate of infinite length with a concentrated load, the bending stress s at any point can be expressed by s ¼ Km ð6P=t2 Þ, and the deflection y at any point by y ¼ Ky ðPa2 =pDÞ, where Km and Ky are dimensionless coeffi-
172
Formulas for Stress and Strain
[CHAP. 8
Figure 8.18
cients that depend upon the location of the load and the point, and D is as defined in Table 11.2. For the load at x ¼ c, z ¼ 0, the stress at any point on the fixed edge x ¼ 0, z ¼ z, and the deflection at any point on the free edge x ¼ a, z ¼ z, can be found by using the following values of Km and Ky :
z=a c=a
1.0
0
0.25
0.50
1.0
1.5
2
1
Km
0.509
0.474
0.390
0.205
0.091
0.037
0
Ky
0.524
0.470
0.380
0.215
0.108
0.049
0
Km
0.428
0.387
0.284
0.140
0.059
0.023
0
0.75 Ky
0.318
0.294
0.243
0.138
0.069
0.031
0
0.50
Km
0.370
0.302
0.196
0.076
0.029
0.011
0
0.25
Km
0.332
0.172
0.073
0.022
0.007
0.003
0
These values are based on the analysis of Jaramillo (Ref. 47), who assumes an infinite length for the plate, and are in good agreement, so far as comparable, with coefficients given by MacGregor (Ref. 26). They differ only slightly from results obtained by Holl (Ref. 27) for a length=span ratio of 4 and by Little (Ref. 49) for a length=span ratio of 5 and are in good agreement with available test data. Wellauer and Seireg (Ref. 48) discuss the results of tests on beams of various proportions and explain and illustrate an empirical method by which the Km values obtained by Jaramillo (Ref. 47) for the infinite plate under concentrated loading can be used to determine approxi-
SEC.
8.12]
Beams; Flexure of Straight Bars
173
mately the stress in a finite plate under an arbitrary transverse loading. The stresses corresponding to the tabulated values of Km are spanwise (x direction) stresses; the maximum crosswise (z direction) stress occurs under the load when the load is applied at the midpoint of the free edge and is approximately equal to the maximum spanwise stress for that loading. Although the previous formulaes are based on the assumption of infinite width of a slab, tests (Ref. 26) on a plate with a width of 8 12 in and span a of 1 14 in showed close agreement between calculated and measured deflections, and Holl’s analysis (Ref. 27), based on the assumption of a plate width four times the span, gives results that differ only slightly from MacGregor’s (Ref. 26). The formulas given should therefore be applicable to slabs of breadth as small as four times the span. 8.12
Beams with Wide Flanges; Shear Lag
In thin metal construction, box, T-, or I-beams with very wide thin cover plates or flanges are sometimes used, and when a thin plate is stiffened by an attached member, a portion of the plate may be considered as a flange, acting integrally with the attached member which forms the web; examples are to be found in ship hulls, floors, tanks, and aircraft. In either type of construction the question arises as to what width of flange or plate would be considered effective; i.e., what width, uniformly stressed to the maximum stress that actually occurs, would provide a resisting moment equal to that of the actual stresses, which are greatest near the web and diminish as the distance from it increases. This problem has been considered by several investigators; the results tabulated on page 174 are due to Hildebrand and Reissner (Ref. 38), Winter (Ref. 39), and Miller (Ref. 28). Let b ¼ actual net width of the flange (or clear distance between webs in continuous plate and stiffener construction), let l ¼ span, and let b0 ¼ effective width of the flange at the section of maximum bending moment. Then the approximate value of b0 =b, which varies with the loading and with the ratio l=b, can be found for beams of uniform section in the table on p. 174. (In this table the case numbers refer to the manner of loading and support represented in Table 8.1.) See also Ref. 37. Some of the more important conclusions stated in Ref. 38 can be summarized as follows. The amount of shear lag depends not only on the method of loading and support and the ratio of span to flange width but also on the ratio of G to E and on the ratio m ¼ ð3Iw þ Is Þ=ðIw þ Is Þ, where Iw and Is are
174
Case no. and load positions (from Table 8.1) 1a. 2a. 2a. 1e. 1e. 1e. 1e. 2e.
a¼0 wa ¼ wl ; a ¼ 0 wa ¼ 0; a ¼ 0 a ¼ l=2 a ¼ l=2 a ¼ l=2 a ¼ l=4 wa ¼ wl ; a ¼ 0
l=b Reference no. 38 38 38 38 39 28 38 38
1
1.25
1.50
1.75
2
2.5
3
4
5
6
8
10
15
20
0.571
0.638
0.690 0.550
0.730 0.600
0.757 0.632
0.530
0.571
0.801 0.685 0.609 0.638
0.830 0.724 0.650 0.686 0.550
0.870 0.780 0.710 0.757 0.670
0.913 0.842 0.784 0.830 0.779
0.934 0.876 0.826 0.870 0.850
0.946 0.899 0.858 0.895 0.894
0.936 0.945
0.946
0.455 0.640
0.495 0.690
0.525 0.560 0.772
0.610 0.830
0.686 0.897
0.895 0.815 0.751 0.801 0.732 0.750 0.740 0.936
0.788 0.957
0.826 0.977
0.855 0.985
0.910 0.991
0.930 0.995
Formulas for Stress and Strain
Ratio of effective width to total width b0 =b for wide flanges
[CHAP. 8
SEC.
8.13]
Beams; Flexure of Straight Bars
175
the moments of inertia about the neutral axis of the beam of the side plates and cover plates, respectively. (The values tabulated from Ref. 38 are for G=E ¼ 0:375 and m ¼ 2.) The value of b0 =b increases with increasing m, but for values of m between 1.5 and 2.5 the variation is small enough to be disregarded. Shear lag at the critical section does not seem to be affected appreciably by the taper of the beam in width, but the taper in cover-plate thickness may have an important effect. In beams with fixed ends the effect of shear lag at the end sections is the same as for a cantilever of span equal to the distance from the point of inflection to the adjacent end. In Ref. 39 it is stated that for a given l=b ratio the effect of shear lag is practically the same for box, I-, T-, and U-beams. The preceding discussion and tabulated factors apply to any case in which the flange is subjected to tension or to compression less than that required to produce elastic instability (see Chap. 15). When a thin flange or sheet is on the compression side, however, it may be stressed beyond the stability limit. For this condition, the effective width decreases with the actual stress. A formula for effective width used in aircraft design is
Flange in compression.
rffiffiffiffi E b ¼ Kt s 0
where s is the maximum compressive stress (adjacent to the supporting web or webs) and K is a coefficient which may be conservatively taken as 0.85 for box beams and 0.60 for a T- or an I-beam having flanges with unsupported outer edges. A theoretical analysis that takes into account both compressive buckling and shear lag is described in Ref. 40. Problems involving shear lag and buckling are most frequently encountered in design with thin-gage metal; good guides to such design are the books ‘‘ColdFormed Steel Design Manual’’ in 5 parts including commentary, published in 1982 by the American Iron and Steel Institute, and ‘‘Aluminum Construction Manual,’’ 4th ed., published in 1981 by the Aluminum Association. See also Ref. 68. 8.13
Beams with Very Thin Webs
In beams with extremely thin webs, such as are used in airplane construction, buckling due to shear will occur at stresses well below the elastic limit. This can be prevented if the web is made shearresistant by the addition of stiffeners such as those used in plate girders, but the number of these required may be excessive. Instead of making the web shear-resistant, it may be permitted to buckle
176
Formulas for Stress and Strain
[CHAP. 8
elastically without damage, the shear being carried wholly in diagonal tension. This tension tends to pull the upper and lower flanges together, and to prevent this, vertical struts are provided which carry the vertical component of the diagonal web tension. A girder so designed is, in effect, a Pratt truss, the web replacing the diagonaltension members and the vertical struts constituting the compression members. In appearance, these struts resemble the stiffeners of an ordinary plate girder, but their function is obviously quite different. A beam of this kind is called a diagonal-tension field beam, or Wagner beam, after Professor Herbert Wagner of Danzig, who is largely responsible for developing the theory. Because of its rather limited field of application, only one example of the Wagner beam will be considered here, viz. a cantilever under end load. Let P ¼ end load, h ¼ depth of the beam, t ¼ thickness of the web, d ¼ spacing of the vertical struts, x ¼ distance from the loaded end to the section in question, Ht and Hc ¼ total stresses in the tension and compression flanges, respectively, at the given section, C ¼ total compression on a vertical strut, and f ¼ unit diagonal tensile stress in the web. Then Ht ¼
Px 1 P; h 2
Hc ¼
Px 1 þ P; h 2
C¼
Pd ; h
f¼
2P ht
The vertical component of the web tension constitutes a beam loading on each individual flange between struts; the maximum value of the resulting bending moment occurs at the struts and is 1 given by Mf ¼ 12 Pd2 =h. The flexural stresses due to Mf must be added to the stresses due to Ht or Hc, which may be found simply by dividing Ht or Hc by the area of the corresponding flange. The horizontal component of the web tension causes a bending moment M ¼ 18 Ph in the vertical strut at the end of the beam unless bending there is prevented by some system of bracing. This end strut must also distribute the load to the web, and should be designed to carry the load as a pin-ended column of length 12 h as well as to resist the moment imposed by the web tension. The intermediate struts are designed as pin-ended columns with lengths somewhat less than h. An adjacent portion of the web is included in the area of the column, the width of the strip considered effective being 30t in the case of aluminum and 60t in the case of steel. Obviously the preceding formulas will apply also to a beam with end supports and center load if P is replaced by the reaction 12 P. Because of various simplifying assumptions made in the analysis, these formulas are conservative; in particular the formula for stress in the vertical struts or stiffeners gives results much larger than actual stresses that have been discovered experimentally. More accurate analyses,
SEC.
8.14]
Beams; Flexure of Straight Bars
177
together with experimental data from various sources, will be found in Refs. 30, 34, 35, 62, and 69–71. 8.14
Beams Not Loaded in Plane of Symmetry; Flexural Center
The formulas for stress and deflection given in Sec. 8.1 are valid if the beam is loaded in a plane of symmetry; they are also valid if the applied loads are parallel to either principal central axis of the beam section, but unless the loads also pass through the elastic axis, the beam will be subjected to torsion as well as bending. For the general case of a beam of any section loaded by a transverse load P in any plane, therefore, the solution comprises the following steps: (1) The load P is resolved into an equal and parallel force P 0 passing through the flexural center Q of the section, and a twisting couple T equal to the moment of P about Q; (2) P 0 is resolved at Q into rectangular components Pu0 and Pv0 , each parallel to a principal central axis of the section; (3) the flexural stresses and deflections due to Pu0 and Pv0 , are calculated independently by the formulas of Sec. 8.1 and superimposed to find the effect of P 0 ; and (4) the stresses due to T are computed independently and superimposed on the stresses due to P 0 , giving the stresses due to the actual loading. (It is to be noted that T may cause longitudinal fiber stresses as well as shear stresses. See Sec. 10.3 and the example at the end of this section.) If there are several loads, the effect of each is calculated separately and these effects added. For a distributed load the same procedure is followed as for a concentrated load. The above procedure requires the determination of the position of the flexural center Q. For any section having two or more axes of symmetry (rectangle, I-beam, etc.) and for any section having a point of symmetry (equilateral triangle, Z-bar, etc.), Q is at the centroid. For any section having only one axis of symmetry, Q is on that axis but in general not at the centroid. For such sections and for unsymmetrical sections in general, the position of Q must be determined by calculation, direct experiment, or the soap-film method (Sec. 6.4). Table 8.12 gives the position of the flexural center for each of a number of sections. When a beam is bent by one or more loads that lie in a plane not parallel to either principal central axis of the section, the neutral axis passes through the centroid but is not perpendicular to the plane of the loads. Let axes 1 and 2 be the principal central axes of the section, and let I1 and I2 represent the corresponding moments of inertia. Then, if the plane of the loads makes with axis 1 an angle a,
Neutral axis.
178
Formulas for Stress and Strain
[CHAP. 8
the neutral axis makes with axis 2 an angle b such that tan b ¼ ðI2 =I1 Þ tan a. It can be seen from this equation that the neutral axis tends to approach the principal central axis about which the moment of inertia is least.
EXAMPLE Figure 8.19(a) represents a cantilever beam of channel section under a diagonal end load applied at one corner. It is required to determine the maximum resulting fiber stress. Solution. For the section (Fig. 8.19b): Iu ¼ 5:61 in4 , Iv ¼ 19:9 in4 ; b ¼ 3:875 in, h ¼ 5:75 in, and t ¼ 14 in. By the formula from Table 8.12, e ¼ b2 h2 t=4Iv ¼ 1:55 in; therefore the flexural center is at Q, as shown. When the load is resolved into vertical and horizontal components at Q and a couple, the results are as shown in Fig. 8.19(b). (Vertical and horizontal components are used because the principal central axes u and v are vertical and horizontal.) The maximum fiber stress will occur at the corner where the stresses due to the vertical and horizontal bending moments are of the same kind; at the upper-right corner f both stresses are tensile, and since f is farther from the u axis than the lower-left corner g where both stresses are compressive, it will sustain the greater stress. This stress will be simply the sum of the stresses due to the vertical and horizontal components of the load, or
s¼
940ð36Þð3Þ 342ð36Þð2:765Þ þ ¼ 5100 þ 6070 ¼ 11;200 lb=in2 19:9 5:61
The effect of the couple depends on the way in which the inner end of the beam is supported. If it is simply constrained against rotation in the planes of bending and twisting, the twisting moment will be resisted wholly by shear stress on the cross section, and these stresses can be found by the appropriate torsion formula of Table 10.1. If, however, the beam is built in so that the flanges are fixed in the horizontal plane, then part of the torque is resisted by the bending rigidity of the flanges and the corresponding moment causes a further fiber stress. This can be found by using the formulas of Sec. 10.3.
Figure 8.19
SEC.
8.15]
Beams; Flexure of Straight Bars
179
For the channel section, K is given with sufficient accuracy by the formula K ¼ ðt3 =3Þðh þ 2bÞ (Table 9.2, case 1), which gives K ¼ 0:073 in4 . Taking G ¼ 12;000;000 lb=in2 , and E ¼ 30;000;000 lb=in2 , and the formula for Cw as Cw ¼
h2 b3 t 2h þ 3b ¼ 38:4 in6 12 h þ 6b
the value for b can be found. From Table 10.3, the formula for b is given as b¼
KG Cw E
1=2 ¼
1=2 0:073ð12Þ ¼ 0:0276 38:4ð30Þ
From Table 10.3, case 1b, the value of y00 at the wall is given as y00 ¼
To 313 tanh bl ¼ tanh 0:0276ð36Þ ¼ 7:47ð106 Þ in2 Cw Eb 38:4ð30 106 Þð0:0276Þ
Therefore the longitudinal compressive stress at f can be found from the expression for sx in Table 10.2, case 1, as sx ¼
hb h þ 3b 00 6ð4Þ 6 þ 3ð4Þ Ey ¼ ð30Þð106 Þð7:47Þð106 Þ ¼ 1610 lb=in2 2 h þ 6b 2 6 þ 6ð4Þ
The resultant fiber stress at f is 11;200 1610 ¼ 9590 lb=in2 .
8.15
Straight Uniform Beams (Common Case); Ultimate Strength
When a beam is stressed beyond the elastic limit, plane sections remain plane or nearly so but unit stresses are no longer proportional to strains and hence no longer proportional to distance from the neutral surface. If the material has similar stress-strain curves in tension and compression, the stress distribution above and below the neutral surface will be similar and the neutral axis of any section which is symmetric about a horizontal axis will still pass through the centroid; if the material has different properties in tension and compression, then the neutral axis will shift away from the side on which the fibers yield the most; this shift causes an additional departure from the stress distribution assumed by the theory outlined in Sec. 8.1. The strength of a beam of ordinary proportions is determined by the maximum bending moment it can sustain. For beams of nonductile material (cast iron, concrete, or seasoned wood) this moment may be calculated by the formula Mm ¼ s0 ðI=cÞ if s0 , the modulus of rupture, is known. The modulus of rupture depends on the material and other factors (see Sec. 3.11), and attempts have been made to calculate it for a given material and section from the form of
Failure In bending.
180
Formulas for Stress and Strain
[CHAP. 8
the complete stress-strain diagram. Thus for cast iron an approximate pffiffiffiffiffiffiffiffi value of s0 may be found by the formula s0 ¼ K c=z0 st , where c is the distance to the extreme fiber, z0 is the distance from the neutral axis to the centroid of the tensile part of the section, and K is an experimental coefficient equal to 65 for sections that are flat at the top and bottom (rectangle, I, T, etc.) and 43 for sections that are pointed or convex at the top and bottom (circle, diamond, etc.) (Ref. 4). Some tests indicate that this method of calculating the breaking strength of cast iron is sometimes inaccurate but generally errs on the side of safety (Ref. 5). In general, the breaking strength of a beam can be predicted best from experimentally determined values of the rupture factor and ultimate strength or the form factor and modulus of rupture. The rupture factors are based on the ultimate tensile strength for all materials except wood, for which it is based on compressive strength. Form factors are based on a rectangular section. For structural steel, wrought aluminum, and other ductile metals, where beams do not actually break, the modulus of rupture means the computed fiber stress at the maximum bending moment (Refs. 6 to 9). When the maximum bending moment occurs at but one section, as for a single concentrated load, the modulus of rupture is higher than when the maximum moment extends over a considerable part of the span. For instance, the modulus of rupture of short beams of brittle material is about 20 percent higher when determined by center loading than when determined by third-point loading. The disparity decreases as the span=depth ratio increases. Beams of ductile material (structural steel or aluminum) do not ordinarily fracture under static loading but fail through excessive deflection. For such beams, if they are of relatively thick section so as to preclude local buckling, the maximum bending moment is that which corresponds to plastic yielding throughout the section. This maximum moment, or ‘‘plastic’’ moment, is usually denoted by Mp and can be calculated by the formula Mp ¼ sy Z, where sy is the lower yield point of the material and Z, called the plastic section modulus, is the arithmetical sum of the statical moments about the neutral axis of the parts of the cross section above and below that axis. Thus, for a rectangular section of depth d and width b, Z ¼ ð12 bdÞð14 dÞ þ ð12 bdÞð14 dÞ ¼ 14 bd2 This method of calculating the maximum resisting moment of a ductile-material beam is widely used in ‘‘plastic design’’ and is discussed further in Sec. 8.16. It is important to note that when the plastic moment has been developed, the neutral axis divides the crosssectional area into halves and so is not always a centroidal axis. It is also important to note that the plastic moment is always greater than
SEC.
8.15]
Beams; Flexure of Straight Bars
181
the moment required to just stress the extreme fiber to the lower yield point. This moment, which may be denoted by My, is equal to sy I=c, and so Mp Z ¼ My I=c This ratio Z=ðI=cÞ, called the shape factor, depends on the form of the cross section. For a solid rectangle it would be 14 bd2 = 16 bd2 , or 1.5; for an I-section it is usually about 1.15. Table A.1 gives formulas or numerical values for the plastic section modulus Z and for the shape factor for most of the cross sections listed. In tubes and beams of thin open section, local buckling or crippling will sometimes occur before the full plastic resisting moment is realized, and the length of the member will have an influence. Tubes of steel or aluminum alloy generally will develop a modulus of rupture exceeding the ultimate tensile strength when the ratio of diameter to wall thickness is less than 50 for steel or 35 for aluminum. Wideflanged steel beams will develop the full plastic resisting moment when the outstanding width=thickness ratio is less than 8.7 for sy ¼ 33;000 lb=in2 or 8.3 for sy ¼ 36;000 lb=in2. Charts giving the effective modulus of rupture of steel, aluminum, and magnesium tubes of various proportions may be found in Ref. 55. Failure by an actual shear fracture is likely to occur only in wood beams, where the shear strength parallel to the grain is, of course, small. In I-beams and similar thin-webbed sections the diagonal compression that accompanies shear (Sec. 7.5) may lead to a buckling failure (see the discussion of web buckling that follows), and in beams of cast iron and concrete the diagonal tension that similarly accompanies shear may cause rupture. The formula for shear stress [Eq. (8.1-2)] may be considered valid as long as the fiber stresses do not exceed the proportional limit, and therefore it may be used to calculate the vertical shear necessary to produce failure in any case where the ultimate shearing strength of the beam is reached while the fiber stresses, at the section of maximum shear, are still within the proportional limit.
Failure in shear.
An I-beam or similar thin-webbed member may fail by buckling of the web owing to diagonal compression when the shear stress reaches a certain value. Ketchum and Draffin (Ref. 11) and Wendt and Withey (Ref. 12) found that in light I-beams this type of buckling occurs when the shear stress, calculated by Web buckling; local failure.
182
Formulas for Stress and Strain
[CHAP. 8
t ¼ 1:25 V =web area (Ref. 11) or t ¼ V =Web area (Ref. 12), reaches a value equal to the unit load that can be carried by a vertical strip of the beam as a round-ended column. For the thin webs of the beams tested, such a thin strip would be computed as a Euler column; for heavier beams an appropriate parabolic or other formula should be used (Chap. 12). In plate girders, web buckling may be prevented by vertical or diagonal stiffeners, usually consisting of double angles that are riveted or welded, one on each side of the web. Steel-construction specifications (Ref. 13) require that such stiffeners be provided when h=t exceeds 70 and v exceeds 64;000;000=ðh=tÞ2 . Such stiffeners should have a moment of inertia (figured for an axis at the center line of the web) equal to at least 0:00000016H 4 and should be spaced so that the clear distance between successive stiffeners is not more than pffiffiffi 11;000t= v or 84 in, whichever is least. Here h is the clear depth of the web between flanges, t is the web thickness, v is the shear stress V =ht, and H is the total depth of the web. In light-metal airplane construction, the stiffeners are sometimes designed to have a moment of inertia about an axis parallel to the web given by I ¼ ð2:29d=tÞ ðVh=33EÞ4=3 , where V ¼ the (total) vertical shear and d ¼ the stiffener spacing center to center (Ref. 14). Buckling failure may occur also as a result of vertical compression at a support or concentrated load, which is caused by either columntype buckling of the web (Refs. 11 and 12) or crippling of the web at the toe of the fillet (Ref. 15). To guard against this latter type of failure, present specifications provide that for interior loads R=tðN þ 2kÞ 4 24;000 and for end reactions R=tðN þ kÞ 4 24;000, where R is the concentrated load or end reaction, t the web thickness, N the length of bearing, and k the distance from the outer face of the flange to the web toe of the fillet. Here R is in pounds and all linear dimensions are in inches. Wood beams will crush locally if the supports are too narrow or if a load is applied over too small a bearing area. The unit bearing stress in either case is calculated by dividing the force by the nominal bearing area, no allowance being made for the nonuniform distribution of pressure consequent upon bending (Ref. 9). Metal beams also may be subjected to high local pressure stresses; these are discussed in Chap. 14.
The compression flange of an I-beam or similar member may fail as a column as a result of lateral buckling if it is unsupported. Such buckling may be elastic or plastic; that is, it may occur at a maximum fiber stress below or above the elastic limit. In the first case the buckling is an example of elastic instability, for which
Lateral buckling.
SEC.
8.15]
Beams; Flexure of Straight Bars
183
relevant formulas are given in Table 15.1. For buckling above the elastic range analytical solutions are difficult to obtain, and empirical expressions based on experiment are used (as will be shown to be true also of the columns discussed in Chap. 12). Moore (Ref. 16) found that standard I-beams fail by lateral buckling when s0 ¼ 40;000 60
ml r
where s0 is the compressive stress in the extreme fiber [computed by Eq. (8.1-1)], l is the span (in inches), r is the radius of gyration (in inches) of the beam section about a central axis parallel to the web, and m is a coefficient which depends on the manner of loading and support and has the following values: Loading and support
Value of m
End supports, uniform load End supports, midpoint load End supports, single load at any point End supports, loads at third points End supports, loads at quarter points End supports, loads at sixth points Cantilever beam, uniform load Cantilever beam, end load Fixed-ended beam, uniform load Fixed-ended beam, midpoint load
0.667 0.500 0.500 0.667 0.750 0.833 0.667 1.000 0.281 0.250
For very light I-beams, Ketchum and Draffin (Ref. 11) found that the lower limit of test results is given by s0 ¼ 24;000 40
ml r
where the terms have the same meaning and m the same values as given previously. The beams tested by Moore generally failed at stresses below but very close to the yield point and so probably could be regarded as representing plastic buckling. The lighter beams tested by Ketchum and Draffin, however, failed at stresses below the limit of proportionality and are examples of elastic buckling. In Ref. 13 rules are given for the reduction in allowable compressive stress according to the unbraced length of the compression flange. A review of the literature on this subject of the lateral buckling of structural members and a bibliography through 1959 are to be found in Ref. 58.
184
Formulas for Stress and Strain
[CHAP. 8
Narrow rectangular beams may fail also as a result of buckling of the compression edge. When this buckling occurs below the elastic limit, the strength is determined by elastic stability; formulas for this case are given in Table 15.1. For buckling at stresses beyond the elastic limit, no simple formula for the critical stress can be given, but methods for calculating this critical stress are given for aluminum beams by Dumont and Hill (Ref. 17) and for wood beams by Trayer and March (Ref. 18).
8.16
Plastic, or Ultimate Strength, Design
The foregoing discussion of beams and frames is based for the most part on the assumption of purely elastic action and on the acceptance of maximum fiber stress as the primary criterion of safety. These constitute the basis of elastic analysis and design. An alternative and often preferred method of design, applicable to rigid frames and statically indeterminate beams made of materials capable of plastic action, is the method of plastic, or ultimate strength, design. It is based on the fact that such a frame or beam cannot deflect indefinitely or collapse until the full plastic moment Mp (see Sec. 8.15) has been developed at each of several critical sections. If it is assumed that the plastic moment—a determinable couple—does indeed act at each such section, then the problem becomes a statically determinate one and the load corresponding to the collapse condition can be readily calculated. A simple illustration of the procedure is afforded by the beam of Fig. 8.20(a), corresponding to case lc of Table 8.1. Suppose it is desired to determine the maximum value of the load W that the beam can support. It is shown by elastic analysis, and is indeed apparent from inspection, that the maximum bending moments occur at the load and at the left end of the beam. The maximum possible value of each such moment is Mp . It is evident that the beam cannot collapse until the
Figure 8.20
SEC.
8.16]
Beams; Flexure of Straight Bars
185
moment at each of these points reaches this value. Therefore, when W has reached its maximum value and collapse is imminent, the beam is acted on by the force system represented in Fig. 8.20(b); there is a plastic hinge and a known couple Mp at each of the critical sections and the problem is statically determinate. For equilibrium of the right half, R ¼ Mp =ðl=2Þ and V1 ¼ R; and for equilibrium of the left half, V2 ¼ W R and ½W Mp =ðl=2Þl=2 ¼ 2Mp or W ¼ 6Mp =l. In attempting to predict the collapse load on the basis of elastic analysis, it is easy to fall into the error of equating the maximum 3 elastic moment 16 Wl at the wall (Table 8.1) to Mp , thus obtaining 16 W ¼ 3 Mp =l. This erroneous procedure fails to take into account the fact that as W increases and yielding commences and progresses at the wall section, there is a redistribution of moments; the moment at the 3 wall becomes less than 16 Wl, and the moment at the load becomes 5 greater than 32 Wl until finally each moment becomes equal to Mp . An important point to note is that although the elastic moments are affected by even a very slight departure from the assumed conditions—perfect fixity at one end and rigid support at the other—the collapse load is not thus affected. So long as the constraints are rigid enough to develop the plastic hinges as indicated, the ultimate load will be the same. Similarly, the method does not require that the beam be uniform in section, although a local reduction in section leading to the formation of a hinge at some point other than those assumed, of course, would alter the solution. For a beam with multiple concentrated transverse loads or with distributed transverse loads, the locations of hinges are not known and must be assumed and verified. A virtual work approach to plastic collapse may permit a more rapid analysis than does the use of equilibrium equations, see Ref. 66. Verification consists of using the equilibrium conditions to construct a moment diagram and determine that no moments larger than the locally permitted values of the fully plastic moment are present. Since nonlinear behavior does not permit superposition of results, one must consider all loads which are acting at a given time. If any of the several loads on a beam tend to cancel the maximum moments due to other loads, one must also consider the order in which the loads are applied in service to assure that the partially loaded beam has not collapsed before all loads have been applied. Column 4 of Table A.1 contains an expression or a numerical value for the plastic section modulus Z and for the shape factor SF ¼ Zc=I for many of the cross sections. Using the plastic section modulus and the value of the yield strength of the material, one can find the full plastic moment Mp . Table 8.13 contains expressions for the loadings which will cause plastic collapse and the locations of the plastic hinges associated with each such loading.
186
Formulas for Stress and Strain
[CHAP. 8
The following example problems illustrate (1) the direct use of the tabulated material and (2) the use of the virtual work approach to a problem where two loads are applied simultaneously and where one plastic hinge location is not obvious. EXAMPLES 1. A hollow aluminum cylinder is used as a transversely loaded beam 6 ft long with a 3-in outer diameter and a 1-in inner diameter. It is fixed at both ends and subjected to a distributed loading which increases linearly from zero at midspan to a maximum value wl at the right end. The yield strength of this material is 27,000 psi, and the value of Wlc at plastic collapse is desired. Solution. From Table A.1 case 15, the expression for the plastic section modulus is given as Z ¼ 1:333ðR3 R3i Þ, which gives Z ¼ 1:333ð1:53 0:53 Þ ¼ 4:33 in3 and Mp ¼ 4:33ð27;000Þ ¼ 117;000 lb-in From Table 8.13 case 2d, with wa ¼ 0 for a uniformly increasing load, the locations of the fully developed plastic hinges are at the two ends and at a distance xh2 from the left end, where 1=2 l2 a3 xh2 ¼ a þ a2 al þ 3 3l Since l ¼ 72 in and a ¼ 86 in, the third hinge is found at xh2 ¼ 50:70 in. The expression for the collapse load wlc is given as wlc ¼
12Mp ðl aÞ ¼ 1703 lb=in ðl xh2 Þðx2h2 3axh2 þ lxh2 þ a3 =lÞ
2. A steel beam of trapezoidal section is shown in Fig. 8.21. It is 1500 mm long, fixed at the right end and simply supported at the left end. The factor of safety of the loading shown is to be determined based on plastic collapse under a proportionately increased set of similar loads. The yield strength of the material is 200 N=mm2 in both tension and compression. All dimensions are in millimeters. Solution. First evaluate Mp . An examination of Table A.1 shows that the plastic section modulus for this cross section is not given. The yield strength in tension and compression is the same, so half the cross-sectional area of
Figure 8.21
SEC.
8.16]
Beams; Flexure of Straight Bars
187
2100 mm2 will be in tension and half in compression under a fully developed plastic hinge. Calculations show that a horizontal axis 16.066 mm above the base will divide this area into equal parts. The centroid of the upper portion is 7.110 mm above this axis, and the centroid of the lower portion is 7.814 mm below. Therefore Mp ¼ 200ð1050Þð7:110 þ 7:814Þ ¼ 3:134ð106 Þ N-mm Let the concentrated load at collapse Pc be accompanied by a uniformly distributed load wc , which equals Pc =1000. During a virtual displacement of the beam when plastic rotation is taking place about the fully developed plastic hinges, the elastic deformations and any deformations due to the development of the plastic hinges remain constant and can be neglected in computing the work done by the loading. The angles shown in Fig. 8.22 are not true slopes at these locations but merely represent the virtual rotations of the fully developed plastic hinges. The location of hinge A is not known at this point in the solution, but it is either under the concentrated load or somewhere in the portion of the beam under the distributed load. Trial 1. Assume that hinge A is under the concentrated load and the virtual displacements are represented by Fig. 8.22(a). The work performed by the loads during their vertical displacements is absorbed by the two plastic hinges. The hinge at A rotates through the angle y þ f and the hinge at B through the angle f. Thus Mp ðy þ f þ fÞ ¼ Pc 1100y þ wc ð900Þð450Þy where wc ¼ Pc =1000 and from geometry 400f ¼ 1100y so that Pc ¼ 4:319ð103 ÞMp , and from the equilibrium of the entire beam one obtains R1 ¼ 3:206ð103 ÞMp . Using these two values and constructing a moment diagram, one finds that a maximum moment of 1:190Mp will be present at a distance of 742 mm from the left end. Thus the assumption that hinge A was under the concentrated load was incorrect. A second trial solution will be carried out by assuming that hinge A is a distance a from the left end. Trial 2. Figure 8.22(b) shows the virtual displacements for this second assumption. Again set the virtual work done by the loading equal to the energy absorbed by the two plastic hinges, or w ya2 900 a Mp ðy þ 2fÞ ¼ Pc 400f þ c þ wc ð900 aÞ 1500 a f 2 2 Note that wc ¼ Pc =1000 and from geometery fð1500 aÞ ¼ ya so that Pc ¼ Mp ½ð1500 þ aÞ=ð1345a 0:75a2 Þ. A minimum value of Pc is desired so
Figure 8.22
188
Formulas for Stress and Strain
[CHAP. 8
this expression is differentiated with respect to a and the derivative set equal to zero. This leads to a ¼ 722:6 mm and Pc ¼ 3:830ð103 ÞMp , a significantly smaller value than before and one which leads to a moment diagram with a maximum positive moment of Mp at a ¼ 722:6 mm and a maximum negative moment of Mp at the right end. This then is the correct solution, and substituting the numerical value for Mp one gets Pc ¼ 12;000 N and wc ¼ 12 N=mm. The applied loads were P ¼ 4000 N and w ¼ 4 N=mm, so the factor of safety is 3.0.
Because of the simplicity, these examples may give an exaggerated impression of the ease of plastic analysis, but they do indicate that for any indeterminate structure with strength that is determined primarily by resistance to bending, the method is well-suited to the determination of ultimate load and—through the use of a suitable factor of safety—to design. Its accuracy has been proved by good agreement between computed and experimental ultimate loads for both beams and frames. An extended discussion of plastic analysis is not appropriate here, but the interested reader will find an extensive literature on the subject (Refs. 60, 61).
Tables
TABLE 8.1
8.17]
Shear, moment, slope, and deflection formulas for elastic straight beams W ¼ load (force); w ¼ unit load (force per unit length); Mo ¼ applied couple (force-length); yo externally created concentrated angular displacement (radians); Do ¼ externally created concentrated lateral displacement; T1 and T2 ¼ temperatures on the top and bottom surfaces, respectively (degrees). RA and RB are the vertical end reactions at the left and right, respectively, and are positive upward. MA and MB are the reaction end moments at the left and right, respectively. All moments are positive when producing compression on the upper portion of the beam cross section. The transverse shear force V is positive when acting upward on the left end of a portion of the beam. All applied loads, couples, and displacements are positive as shown. All deflections are positive upward, and all slopes are positive when up and to the right. E is the modulus of elasticity of the beam material, and I is the area moment of inertia about the centroidal axis of the beam cross section. g is the temperature coefficient of expansion (unit strain per degree) NOTATION:
SEC.
8.17
Transverse shear ¼ V ¼ RA Whx ai0
1. Concentrated intermediate load
Bending moment ¼ M ¼ MA þ RA x Whx ai Slope ¼ y ¼ y þ
MA x RA x2 W þ hx ai2 EI 2EI 2EI
Deflection ¼ y ¼ yA þ yA x þ
MA x2 RA x3 W hx ai3 þ 6EI 2EI 6EI
ðNote: see page 131 for a definition of the term hx ain :Þ
Boundary values
Selected maximum values of moments and deformations
2
1a. Left end free, right end fixed (cantilever)
1b. Left end guided, right end fixed
RA ¼ 0
MA ¼ 0
yA ¼
W ðl aÞ 2EI
Max M ¼ MB ; max possible value ¼ Wl when a ¼ 0
W ð2l3 3l2 a þ a3 Þ yA ¼ 6EI
Max y ¼ yA ; max possible value ¼
Wl2 when a ¼ 0 2EI
RB ¼ W
Max y ¼ yA ; max possible value ¼
Wl3 when a ¼ 0 3EI
MB ¼ W ðl aÞ
yB ¼ 0
yB ¼ 0
RA ¼ 0
MA ¼
yA ¼
W ðl aÞ2 2l
W ðl aÞ2 ðl þ 2aÞ 12EI
yB ¼ 0
MB ¼ yB ¼ 0
W ðl2 a2 Þ 2l
Max þ M ¼ MA ; max possible value ¼
Wl when a ¼ 0 2
Max M ¼ MB ; max possible value ¼
Wl when a ¼ 0 2
Max y ¼ yA ; max possible value ¼
Wl3 when a ¼ 0 12EI
189
RB ¼ W
yA ¼ 0
Beams; Flexure of Straight Bars
End restraints, reference no.
TABLE 8.1
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued)
1d. Left end fixed, right end fixed
Selected maximum values of moments and deformations
RA ¼
W ðl aÞ2 ð2l þ aÞ 2l3
yA ¼
Wa ðl aÞ2 4EIl
yA ¼ 0
RB ¼
Wa 2 ð3l a2 Þ 2l3
yB ¼ 0
MB ¼
Wa 2 ðl a2 Þ 2l2
yB ¼ 0
RA ¼
W ðl aÞ2 ðl þ 2aÞ l3
Max þ M ¼
MA ¼
Wa ðl aÞ2 l2
l l Max M ¼ MA if a < ; max possible value ¼ 0:1481Wl when a ¼ 2 3
yA ¼ 0
MA ¼ 0
Max þ M ¼
Max M ¼ MB ; max possible value ¼ 0:1924Wl when a ¼ 0:5773l
yA ¼ 0
Max y ¼
1=2 1=2 Wa a a ðl aÞ2 at x ¼ l when a > 0:414l 6EI 2l þ a 2l þ a
Max y ¼
Waðl2 a2 Þ3 lðl2 þ a2 Þ Wl3 at x ¼ 2 when a < 0:414l; max possible y ¼ 0:0098 when x ¼ a ¼ 0:414l 3l a2 EI 3EIð3l2 a2 Þ2
Max y ¼
Wa2 RB ¼ 3 ð3l 2aÞ l MB ¼
yB ¼ 0
RA ¼
W ðl aÞ l
yA ¼
Wa ð2l aÞðl aÞ 6EIl
RB ¼
Wa l
yB ¼
Wa 2 ðl a2 Þ 6EIl
RA ¼ 0
MA ¼ 0
RB ¼ W
yA ¼ 0
MB ¼ 0
Max y ¼ ¼
MB ¼ 0 yB ¼ 0
3=2 Wa l2 a2 3 3EIl l l when a ¼ 2 2
l Wl2 Max y ¼ yA when a < ; max possible value ¼ 0:0642 when a ¼ 0:423l 2 EI
yB ¼ 0
MA ¼ W ðl aÞ
W 2 ðl a2 Þ 2EI
Wl l when a ¼ 4 2 2 1=2 l a2 l Wl3 at x at x ¼ l when a < ; max possible value ¼ 3 48EI 2
Max M ¼ RA a at x ¼ a; max possible value ¼
yA ¼ 0
W ðl aÞ 2 yA ¼ ð2l þ 2al a2 Þ 6EI
yB ¼
2W ðl aÞ2 a3 2al l Wl3 l at x ¼ if a > ; max possible value ¼ when x ¼ a ¼ l þ 2a 2 2 192EI 3EIðl þ 2aÞ2
Max M ¼ MA for 0 < x < a; max possible value ¼ Wl when a ¼ 0 Max y ¼ yB ; max possible value ¼
Wl2 when a ¼ 0 2EI
Max y ¼ yA ; max possible value ¼
Wl3 when a ¼ 0 3EI
[CHAP. 8
1f. Left end guided, right end simply supported
2Wa2 Wl l ðl aÞ2 at x ¼ a; max possible value ¼ when a ¼ 8 2 l3
Wa2 ðl aÞ l2
yB ¼ 0
1e. Left end simply supported, right end simply supported
Wa ðl aÞ2 ð2l þ aÞ at x ¼ a; max possible value ¼ 0:174Wl when a ¼ 0:366l 2l3
Formulas for Stress and Strain
1c. Left end simply supported right end fixed
Boundary values
190
End restraints, reference no.
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued)
SEC.
TABLE 8.1
8.17]
2. Partial distributed load
Transverse shear ¼ V ¼ RA wahx ai Bending moment ¼ M ¼ MA þ RA x Slope ¼ y ¼ yA þ
2a. Left end free, right end fixed (cantilever)
wa w wa hx ai2 l hx ai3 2 6ðl aÞ
MA x RA x2 w wl wa þ a hx ai3 hx ai4 EI 2EI 6EI 24EIðl aÞ
Deflection ¼ y ¼ yA þ yA þ yA x þ
End restraints, reference no.
wl wa hx ai2 2ðl aÞ
MA x2 RA x3 w ðwl wa Þ þ a hx ai4 hx ai5 120EIðl aÞ 2EI 6EI 24EI
Boundary values RA ¼ 0
MA ¼ 0
Selected maximum values of moments and deformations If a ¼ 0 and wl ¼ wa ðuniform load on entire spanÞ; then wa l2 2
wa l3 6EI
wa w wa ðl aÞ3 þ l ðl aÞ3 6EI 24EI
Max M ¼ MB ¼
yA ¼
wa w wa ðl aÞ3 ð3l þ aÞ l ðl aÞ3 ð4l þ aÞ 24EI 120EI
Max y ¼ yA ¼
RB ¼
wa þ wl ðl aÞ 2
If a ¼ 0 and wa ¼ 0 ðuniformly increasing loadÞ; then
MB ¼
wa w wa ðl aÞ2 l ðl aÞ2 2 6
Max M ¼ MB ¼
yB ¼ 0
yB ¼ 0
Max y ¼ yA ¼
Max y ¼ yA ¼
wa l4 8EI
wl l2 6
Max y ¼ yA ¼
wl l3 24EI
wl l4 30EI
If a ¼ 0 and wl ¼ 0 ðuniformly decreasing loadÞ; then Max M ¼ MB ¼ Max y ¼ yA ¼
wa l2 3
11wa l4 120EI
Max y ¼ yA ¼
wa l3 8EI
Beams; Flexure of Straight Bars
yA ¼
191
TABLE 8.1
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued)
2b. Left end guided, right end fixed
Boundary values RA ¼ 0
yA RB MB
yB ¼ 0
yB ¼ 0
If a ¼ 0 and wl ¼ wa ðuniform load on entire spanÞ; then Max M ¼ MB ¼ Max y ¼ yA ¼
wa l2 3
wa l2 6
Max þ M ¼ MA ¼
Formulas for Stress and Strain
MA
yA ¼ 0
w w wa ðl aÞ3 ¼ a ðl aÞ3 þ l 6l 24l wa w wa ðl aÞ3 ðl þ aÞ l ðl aÞ3 ð3l þ 2aÞ ¼ 24EI 240EI w þ wl ¼ a ðl aÞ 2 wa w wa ðl aÞ2 ð2l þ aÞ l ðl aÞ2 ð3l þ aÞ ¼ 6l 24l
Selected maximum values of moments and deformations
wa l4 24EI
If a ¼ 0 and wa ¼ 0 ðuniformly increasing loadÞ; then wl l2 8 wl l4 Max y ¼ yA ¼ 80EI
Max þ M ¼ MA ¼
Max M ¼ MB ¼
wl l2 24
If a ¼ 0 and wl ¼ 0 ðuniformly decreasing loadÞ; then 5wa l2 24 7wa l4 Max y ¼ yA ¼ 240EI
Max M ¼ MB ¼
2c. Left end simply supported, right end fixed
wa w w ðl aÞ3 ð3l þ aÞ þ l 3 a ðl aÞ3 ð4l þ aÞ 8l3 40l wa w wa yA ¼ ðl aÞ3 ðl þ 3aÞ l ðl aÞ3 ð2l þ 3aÞ 48EIl 240EIl
RA ¼
MA ¼ 0
yA ¼ 0
w þ wl RB ¼ a ðl aÞ RA 2 wa w wa M B ¼ RA l ðl aÞ2 l ðl aÞ2 2 6 yB ¼ 0
yB ¼ 0
Max þ M ¼ MA ¼
192
End restraints, reference no.
wa l2 8
If a ¼ 0 and wl ¼ wa ðuniform load on entire spanÞ; then RA ¼ 38 wa l
RB ¼ 58 wa l
Max M ¼ MB ¼
Max þ M ¼
9wa l2 at x ¼ 38 l 128
Max y ¼ yA ¼
Max y ¼ 0:0054
wa l2 8
wa l3 48EI
wa l4 at x ¼ 0:4215l EI
If a ¼ 0 and wa ¼ 0 ðuniformly increasing loadÞ; then RA ¼
wl l 10
RB ¼
2wl l 5
Max M ¼ MB ¼
Max þ M ¼ 0:0298wl l2 at x ¼ 0:4472l Max y ¼ 0:00239
wl l2 15
Max y ¼ yA ¼
wl l3 120EI
wl l4 at x ¼ 0:4472l EI
RA ¼ 11 40 wa l
9 RB ¼ 40 wa l
7 Max M ¼ MB ¼ 120 wa l2
2
Max þ M ¼ 0:0422wa l at x ¼ 0:329l Max y ¼ yA ¼
wa l3 80EI
Max y ¼ 0:00304
wa l4 ; at x ¼ 0:4025l EI
[CHAP. 8
If a ¼ 0 and wl ¼ 0 ðuniformly decreasing loadÞ; then
TABLE 8.1
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued) SEC.
8.17]
2d. Left end fixed, right end fixed
wa w w ðl aÞ3 ðl þ aÞ þ l 3 a ðl aÞ3 ð3l þ 2aÞ 2l3 20l wa w w ðl aÞ3 ðl þ 3aÞ l 2 a ðl aÞ3 ð2l þ 3aÞ MA ¼ 2 12l 60l RA ¼
yA ¼ 0
yA ¼ 0
wa þ wl ðl aÞ RA 2 w w wa ðl aÞ2 MB ¼ RA l þ MA a ðl aÞ2 l 2 6 RB ¼
yB ¼ 0
yB ¼ 0
If a ¼ 0 and wl ¼ wa (uniform load on entire span), then Max M ¼ MA ¼ MB ¼ Max y ¼
wa w wa ðl aÞ2 þ l ðl aÞ2 2l 6l
MA ¼ 0
yA ¼ 0
wa ðl aÞ2 ðl2 þ 2al a2 Þ 24EIl w wa l ðl aÞ2 ð7l2 þ 6al 3a2 Þ 360EIl w þ wl RB ¼ a ðl aÞ RA 2 wa ðl2 a2 Þ2 yB ¼ 24EIl wl wa ðl aÞ2 ð8l2 þ 9al þ 3a2 Þ þ 360EIl yA ¼
MB ¼ 0
yB ¼ 0
wa l2 l at x ¼ 2 24
If a ¼ 0 and wa ¼ 0 (uniformly increasing load), then RA ¼
3wl l 20
MA ¼
wl l2 30
RB ¼
7wl l 20
Max M ¼ MB ¼
wl l2 20
Max þ M ¼ 0:0215wl l2 at x ¼ 0:548l wl l4 at x ¼ 0:525l EI
If a ¼ 0 and wl ¼ wa (uniform load on entire span), then RA ¼ RB ¼
wa l 2
Max y ¼ yB ¼
Max M ¼
wa l3 24EI
wa l2 l at x ¼ 8 2
Max y ¼
5wa l4 l at x ¼ 2 384EI
If a ¼ 0 and wa ¼ 0 (uniformly increasing load), then RA ¼
wl l 6
yA ¼
7wl l3 360EI
RB ¼
wl l 3
yB ¼
Max y ¼ 0:00653
Max M ¼ 0:0641wl l2 at x ¼ 0:5773l
wl l3 45EI
wl l4 at x ¼ 0:5195l EI
Beams; Flexure of Straight Bars
RA ¼
Max þ M ¼
wa l4 l at x ¼ 2 384EI
Max y ¼ 0:001309
2e. Left end simply supported, right end simply supported
wa l2 12
193
TABLE 8.1
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued)
RA ¼ 0
Selected maximum values of moments and deformations
yA ¼ 0
If a ¼ 0 and wl ¼ wa (uniform load on entire span), then wa l2 2
wa l3 3EI
wa w wa ðl aÞ2 þ l ðl aÞ2 2 6 wa ðl aÞ2 ð5l2 þ 2al a2 Þ yA ¼ 24EI w wa ðl aÞ2 ð9l2 þ 2al a2 Þ l 120EI w þ wl ðl aÞ RB ¼ a 2 wa w wa yB ¼ ðl aÞ2 ð2l þ aÞ þ l ðl aÞ2 ð3l þ aÞ 6EI 24EI
If a ¼ 0 and wa ¼ 0 (uniformly increasing load), then
MB ¼ 0
If a ¼ 0 and wl ¼ 0 (uniformly decreasing load), then
MA ¼
yB ¼ 0
Max M ¼ MA ¼ Max y ¼ yA ¼
5wa l4 24EI
Max M ¼ MA ¼ Max y ¼ yA ¼
wl l2 6
Max y ¼ yB ¼
wl l3 8EI
3wl l4 40EI
Max M ¼ MA ¼ Max y ¼ yA ¼
Max y ¼ yB ¼
wa l2 3
Max y ¼ yB ¼
5wa l3 24EI
2wa l4 15EI
Formulas for Stress and Strain
2f. Left end guided, right end simply supported
Boundary values
194
End restraints, reference no.
Transverse shear ¼ V ¼ RA
3. Concentrated intermediate moment
Bending moment ¼ M ¼ MA þ RA x þ Mohx ai0 Slope ¼ y ¼ yA þ
MA x RA x2 Mo hx ai þ þ EI 2EI EI
Deflection ¼ y ¼ yA þ yA x þ
End restraints, reference no. 3a. Left end free, right end fixed (cantilever)
MA x2 RA x3 Mo þ þ hx ai2 2EI 6EI 2EI
Boundary values RA ¼ 0
MA ¼ 0
Selected maximum values of moments and deformations Max M ¼ Mo Max y ¼ yA ; max possible value ¼
Mo l when a ¼ 0 EI
Mo ðl2 a2 Þ 2EI
Max y ¼ yA ; max possible value ¼
Mo l 2 when a ¼ 0 2EI
yA ¼
RB ¼ 0
MB ¼ Mo
yB ¼ 0
yB ¼ 0
[CHAP. 8
Mo ðl aÞ yA ¼ EI
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued)
SEC.
TABLE 8.1
8.17]
3b Left end guided, right end fixed
RA ¼ 0
Max þ M ¼ MB ; max possible value ¼ Mo when a ¼ l
MA ¼
Mo ðl aÞ l
Max M ¼ MA ; max possible value ¼ Mo when a ¼ 0
yA ¼
Mo aðl aÞ 2EI
Max y ¼ yA ; max possible value ¼
RB ¼ 0 M a MB ¼ o l
3c. Left end simply supported, right end fixed
yA ¼ 0
yB ¼ 0 yB ¼ 0
RA ¼
3Mo 2 ðl a2 Þ 2l3
yA ¼
Mo ðl aÞð3a lÞ 4EIl yA ¼ 0
RB ¼
3Mo 2 ðl a2 Þ 2l3
MB ¼
Mo ð3a2 l2 Þ 2l2
Max þ M ¼ Mo þ RA a just right of x ¼ a; max possible value ¼ Mo when a ¼ 0 or a ¼ l; min possible value ¼ 0:423Mo when a ¼ 0:577l Max M ¼
3Mo a 2 ðl a2 Þ just left of x ¼ a if a > 0:282l; max possible value ¼ 0:577Mo 2l3
when a ¼ 0:577l Mo 2 ðl 3a2 Þ at B if a < 0:282l; max possible value ¼ 0:5Mo when a ¼ 0 2l2 rffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi Mo ðl aÞ 3a l M l2 ffi ð3a lÞ3=2 at x ¼ l Max þ y ¼ pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ; max possible value ¼ 0:0257 o at x ¼ 0:474l 3l þ 3a EI 6 3ðl þ aÞEI
Max M ¼
yB ¼ 0
yB ¼ 0
when a ¼ 0:721l l Note: There is no positive deflection if a < 3 Max y occurs at x ¼
" # rffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a2 a4 2l3 1 M0 l2 l 16 þ9 1 at x ¼ ; max possible value ¼ 2 a Þ 27EI 2 l l 3
3ðl2
Beams; Flexure of Straight Bars
MA ¼ 0
Mo l2 l when a ¼ 8EI 2
when a ¼ 0
195
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued)
End restraints, reference no.
RA ¼
6Mo a ðl aÞ l3
Max þ M ¼
Mo ð4al2 9a2 l þ 6a3 Þ just right of x ¼ a; max possible value ¼ Mo when a ¼ l l3
MA ¼
Mo 2 ðl 4al þ 3a2 Þ l2
Max M ¼
Mo ð4al2 9a2 l þ 6a3 l3 Þ just left of x ¼ a; max possible value ¼ Mo when a ¼ 0 l3
yA ¼ 0
2MA3 l M l2 ð3a lÞ; max possible value ¼ 0:01617 o at x ¼ 0:565l when a ¼ 0:767l at x ¼ EI 3a 3R2A EI l Note: There is no positive deflection if a < 3
yA ¼ 0
Max þ y ¼
RB ¼ RA MB ¼
Mo ð3a2 2alÞ l2
yB ¼ 0
3e. Left end simply supported, right end simply supported
yB ¼ 0
RA ¼
Mo l
Max þ M ¼
Mo ðl aÞ just right of x ¼ a; max possible value ¼ Mo when a ¼ 0 l
yA ¼
Mo 2 ð2l 6al þ 3a2 Þ 6EIl
Max M ¼
Mo a just left of x ¼ a; max possible value ¼ Mo when a ¼ l l
MA ¼ 0
yA ¼ 0
Max þ y ¼
M RB ¼ o l
MB ¼ 0
yB ¼ 0
RA ¼ 0
yA ¼ 0
M a yA ¼ o ð2l aÞ 2EI
Mo a EI
yB ¼ 0
Max y ¼ yB ; max possible value ¼
Mo l when a ¼ l EI
Max y ¼ yA ; max possible value ¼
Mo l2 when a ¼ l 2EI
[CHAP. 8
yB ¼
MB ¼ 0
Mo l2 at x ¼ 0:577l when a ¼ l ðNote: There is no positive deflection if a < 0:423lÞ EI
Max M ¼ Mo for 0 < x < a
MA ¼ Mo
RB ¼ 0
Mo ð6al 3a2 2l2 Þ3=2 pffiffiffi at x ¼ ð2al a2 23 l2 Þ1=2 when a > 0:423l; max possible value 9 3EIl
¼ 0:0642
Mo 2 ðl 3a2 Þ yB ¼ 6EIl
3f. Left end guided, right end simply supported
Selected maximum values of moments and deformations
Formulas for Stress and Strain
3d. Left end fixed, right end fixed
Boundary values
196
TABLE 8.1
TABLE 8.1
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued) Transverse shear ¼ V ¼ RA Bending moment ¼ M ¼ MA þ RA x MA x RA x2 þ yohx ai0 þ 2EI EI
Deflection ¼ y ¼ yA þ yA x þ
End restraints, reference no. MA ¼ 0
yA ¼ yo
yA ¼ yo a
RB ¼ 0
MB ¼ 0
yB ¼ 0
yB ¼ 0
RA ¼ 0 yA ¼ 0
yB ¼ 0
EIyo l yB ¼ 0
MA ¼ 0
yA ¼ 0
RB ¼ 0
4c. Left end simply supported, right end fixed
EIyo l l yA ¼ yo a 2
MA ¼
MB ¼
Selected maximum values of moments and deformations Max y ¼ yA ; max possible value ¼ yo l when a ¼ l
Max M ¼ MA l y l Max þ y ¼ yA when a > ; max possible value ¼ o when a ¼ l 2 2 Max y ¼
yo yo l ðl aÞ2 at x ¼ a; max possible value ¼ when a ¼ 0 2l 2
3EIyo when a ¼ l l 1=2 2l at x ¼ l 1 when a 23 l; max possible value ¼ 0:1926yo l at x ¼ 0:577l 3a
Max M ¼ MB ; max possible value ¼ 3=2 2l Max þ y ¼ yo a 1 3a
RB ¼ RA
2 when a ¼ l ðNote: There is no positive deflection if a < lÞ 3 3a a3 þ 3 at x ¼ a; max possible value ¼ 0:232yo l at x ¼ 0:366l when a ¼ 0:366l Max y ¼ yo a 1 2l 2l
3EIayo l3 3a yA ¼ yo 1 2l
MB ¼
3EIayo l2
yB ¼ 0
yB ¼ 0
197
RA ¼
Beams; Flexure of Straight Bars
4b. Left end guided, right end fixed
MA x2 RA x3 þ þ yohx ai 2EI 6EI
Boundary values RA ¼ 0
8.17]
Slope ¼ y ¼ yA þ
4a. Left end free, right end fixed
SEC.
4. Intermediate externally created angular deformation
TABLE 8.1
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued) Selected maximum values of moments and deformations
RA ¼
6EIyo ðl 2aÞ l3
l 2EIyo when a ¼ 0 Max þ M ¼ MB when a < ; max possible value ¼ 2 l
MA ¼
2EIy ð3a 2lÞ l2
l 4EIyo Max M ¼ MA when a < ; max possible value ¼ when a ¼ 0 l 2
yA ¼ 0
l2 l 4 ly when a ¼ 0 if a < ; max possible value ¼ 3 27 o 3ðl 2aÞ l 2 Note: There is no positive deflection if < a < l 3 3
yA ¼ 0
Max þ y occurs at x ¼
RB ¼ RA MB ¼
2EIyo ðl 3aÞ l2
yB ¼ 0
4e. Left end simply supported, right end simply supported
yB ¼ 0
RA ¼ 0
MA ¼ 0
Max y ¼
y ðl aÞ yA ¼ 0 l RB ¼ 0 MB ¼ 0 yA ¼
yB ¼ 0
4f. Left end guided, right end simply supported
Max y ¼
yB ¼
RA ¼ 0
MA ¼ 0 yA ¼ yo ðl aÞ MB ¼ 0
yB ¼ 0
yB ¼ yo
5. Intermediate externally created lateral displacement
yo a yo l l ðl aÞ at x ¼ a; max possible value ¼ when a ¼ l 4 2
yo l
yA ¼ 0 RB ¼ 0
2yo a2 yo l l ðl aÞ2 at x ¼ a; max possible value ¼ when a ¼ l3 8 2
Formulas for Stress and Strain
4d. Left end fixed, right end fixed
Boundary values
198
End restraints, reference no.
Max y ¼ yA ; max possible value ¼ yo l when a ¼ 0
Transverse shear ¼ V ¼ RA Bending moment ¼ M ¼ MA þ RA x Slope ¼ y ¼ yA þ
Deflection ¼ y ¼ yA þ yA x þ
MA x2 RA x3 þ þ Dohx ai0 2EI 6EI
[CHAP. 8
M A x RA x 2 þ EI 2EI
5a. Left end free, right end fixed
yA ¼ Do
RB ¼ 0
MB ¼ 0
yB ¼ 0
yB ¼ 0
RA ¼ 0
MA ¼ 0
yA ¼ 0
yA ¼ Do
RB ¼ 0
MB ¼ 0
yB ¼ 0
yB ¼ 0
3EIDo l3 3Do yA ¼ 2l RA ¼
RB ¼ RA yB ¼ 0
MA ¼ 0
Max M ¼ MB
yA ¼ 0
D Max þ y ¼ o3 ð2l3 þ a3 3l2 aÞ just right of x ¼ a; max possible value ¼ Do when a ¼ 0 2l
3EIDo l2 yB ¼ 0 MB ¼
12EIDo l3 6EIDo MA ¼ l2 RB ¼ RA RA ¼
Do a 2 ð3l a2 Þ just left of x ¼ a; max possible value ¼ Do when a ¼ l 2l3
Max þ M ¼ MB
yA ¼ 0
3Do l at x ¼ Max y ¼ 2l 2
Max M ¼ MA
Max þ y ¼
Do 3 ðl þ 2a3 3a2 lÞ just right of x ¼ a; max possible value ¼ Do when a ¼ 0 l3
Max y ¼
Do a2 ð3l 2aÞ just left of x ¼ a; max possible value ¼ Do when a ¼ l l3
MA ¼ 0
Max þ y ¼
Do ðl aÞ just right of x ¼ a; max possible value ¼ Do when a ¼ 0 l
Max y ¼
RB ¼ 0
Do yA ¼ l MB ¼ 0
Do a just left of x ¼ a; max possible value ¼ Do when a ¼ l l
yB ¼ 0
yB ¼
RA ¼ 0 yA ¼ 0
yB ¼ 0
Do l
RA ¼ 0
MA ¼ 0
yA ¼ 0
yA ¼ Do
RB ¼ 0
MB ¼ 0
yB ¼ 0
yB ¼ 0
Max y ¼ yA when x < a
199
5f. Left end guided, right end simply supported
Max y ¼
Max y ¼ yA
yA ¼ 0
MB ¼ MA
yB ¼ 0
5e. Left end simply supported, right end simply supported
Max y ¼ yA when x < a
Beams; Flexure of Straight Bars
5d. Left end fixed, right end fixed
Max y ¼ yA when x < a
8.17]
5c. Left end simply supported, right end fixed
MA ¼ 0
SEC.
5b. Left end guided, right end fixed
RA ¼ 0 yA ¼ 0
TABLE 8.1
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued) Transverse shear ¼ V ¼ RA
6. Uniform temperature variation from top to bottom from a to l
Slope ¼ y ¼ yA þ
200
Bending moment ¼ M ¼ MA þ RA x MA x RA x2 g þ þ ðT2 T1 Þhx ai EI t 2EI MA x2 RA x3 g þ þ ðT2 T1 Þhx ai2 2t 2EI 6EI
g ¼ temperature coefficient of expansion (unit strain/ ) t ¼ depth of beam End restraints, reference no. 6a. Left end free, right end fixed
Boundary values RA ¼ 0
MA ¼ 0
g ðT2 T1 Þðl aÞ t g yA ¼ ðT2 T1 Þðl2 a2 Þ 2t
yA ¼
6b. Left end guided, right end fixed
6c. Left end simply supported, right end fixed
RB ¼ 0
MB ¼ 0
yB ¼ 0
yB ¼ 0
RA ¼ 0
yA ¼ 0
EIg ðT2 T1 Þðl aÞ MA ¼ lt ag yA ¼ ðT2 T1 Þðl aÞ 2t RB ¼ 0
MB ¼ MA
yB ¼ 0
yB ¼ 0
MA ¼ 0
yA ¼ 0
RB ¼ RA yB ¼ 0
M B ¼ RA l yB ¼ 0
M ¼ 0 everywhere Max y ¼ yA ; max possible value ¼
gl ðT2 T1 Þ when a ¼ 0 t
Max y ¼ yA ; max possible value ¼
gl2 ðT T1 Þ when a ¼ 0 2t 2
M ¼ MA everywhere; max possible value ¼ Max y ¼
EIg ðT2 T1 Þ when a ¼ 0 t
ag gl l ðT2 T1 Þðl aÞ at x ¼ a; max possible value ¼ ðT2 T1 Þ when a ¼ lt 4t 2
Max y ¼ yA ; max possible value ¼
gl2 l ðT T1 Þ when a ¼ 2 8t 2
3EIg ðT2 T1 Þ when a ¼ 0 2t 1=2 gðT2 T1 Þðl aÞ 3a l pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð3a lÞ3=2 at x ¼ l Max þ y ¼ ; max possible value 3l þ 3a 6t 3ðl þ aÞ
Max M ¼ MB ; max possible value ¼
gl2 ðT2 T1 Þ at x ¼ 0:474l when a ¼ 0:721l ðNote: There is no positive deflection if a < l=3Þ t " # rffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a2 a4ffi 2l3 1 gl2 l 1 6 1 ðT T1 Þ at x ¼ ; max possible value ¼ þ 9 Max y occurs at x ¼ 2 2 l l 3 3ðl a2 Þ 27t 2 ¼ 0:0257
when a ¼ 0
[CHAP. 8
3EIg ðT2 T1 Þðl2 a2 Þ RA ¼ 2tl3 g yA ¼ ðT T1 Þðl aÞð3a lÞ 4tl 2
Selected maximum values of moments and deformations
Formulas for Stress and Strain
Deflection ¼ y ¼ yA þ yA x þ
6d. Left end fixed, right end fixed
RA ¼ MA ¼
6EIag ðT2 T1 Þðl aÞ tl3 EIg ðT2 T1 Þðl aÞð3a lÞ tl2
yA ¼ 0
yA ¼ 0
EIg ðT2 T1 Þ when a ¼ 23 l 3t l Note: There is no positive moment if a < 3
Max þ M ¼ MA ; max possible value ¼
Max M ¼ MB ; max possible value ¼
RB ¼ RA MB ¼
yB ¼ 0
yB ¼ 0
RA ¼ 0
MA ¼ 0
yA ¼ 0
g yA ¼ ðT T1 Þðl aÞ2 2tl 2 RB ¼ 0
MB ¼ 0
yB ¼ 0
g ðT Tl Þðl2 a2 Þ yB ¼ 2tl 2
6f. Left end guided, right end simply supported
RA ¼ 0
MA ¼ 0
yA ¼ 0
g yA ¼ ðT T1 Þðl aÞ2 2t 2 RB ¼ 0
MB ¼ 0
g yB ¼ ðT2 T1 Þðl aÞ l
yB ¼ 0
4EIg l ðT2 T1 Þ when a ¼ 3t 3
2MA2 l gl2 ð3l aÞ; max possible value ¼ 0:01617 ðT2 T1 Þ at x ¼ 0:565l at x ¼ 3a t 3R2A EI l when a ¼ 0:767l Note: There is no positive deflection if a < 3
Max þ y ¼
M ¼ 0 everywhere Max þ y ¼ yB ; max possible value ¼
gl ðT T1 Þ when a ¼ 0 2t 2
Max y ¼ yA ; max possible value ¼
gl ðT2 T1 Þ when a ¼ 0 2t
Max y ¼
g gl2 l ðT2 T1 Þ at x ¼ when a ¼ 0 ðT T1 Þðl2 a2 Þ2 ; max possible value ¼ 8t 8tl2 2 2
M ¼ 0 everywhere Max y ¼ yB ; max possible value ¼
gl ðT T1 Þ when a ¼ 0 t 2
Max y ¼ yA ; max possible value ¼
gl2 ðT2 T1 Þ when a ¼ 0 2t
Beams; Flexure of Straight Bars
6e. Left end simply supported, right end simply supported
EIg ðT2 T1 Þðl aÞð3a þ lÞ tl2
8.17]
Shear, moment, slope, and deflection formulas for elastic straight beams (Continued)
SEC.
TABLE 8.1
201
NOTATION:
Reaction and deflection formulas for in-plane loading of elastic frames
W ¼ load (force); w ¼ unit load (force per unit length); Mo ¼ applied couple (force-length); yo ¼ externally created concentrated angular displacement (radians); Do ¼ externally created
202
TABLE 8.2
concentrated lateral displacement (length); T To ¼ uniform temperature rise (degrees); T1 and T2 ¼ temperature on outside and inside, respectively (degrees). HA and HB are the horizontal end
(length to the fourth); E1 , E2 , and E3 are the respective moduli of elasticity (force per unit area); g1 , g2 , and g3 are the respective temperature coefficients of expansions (unit strain per degree) General reaction and deformation expressions for cases 1–4, right end pinned in all four cases Deformation equations: Horizontal deflection at A ¼ dHA ¼ AHH HA þ AHM MA LPH Angular rotation at A ¼ cA ¼ AMH HA þ AMM MA LPM where AHH ¼
l31 I3 l þ 2 þ 3 ðl2 þ l1 l2 þ l22 Þ 3E1 I1 3E2 I2 3E3 I3 1
AHM ¼ AMH ¼ AMM ¼
l21 l þ 3 ð2l þ l2 Þ 2E1 I1 6E3 I3 1
Formulas for Stress and Strain
reactions at the left and right, respectively, and are positive to the left; VA and VB are the vertical end reactions at the left and right, respectively, and are positive upwards; MA and MB are the reaction moments at the left and right, respectively, and are positive clockwise. I1 , I2 , and I3 are the respective area moments of inertia for bending in the plane of the frame for the three members
l1 l þ 3 E1 I1 3E3 I3
and where LPH and LPM are loading terms given below for several types of load (Note: VA , VB ; and HB are to be evaluated from equilibrium equations after calculating HA and MA ) 1. Left end pinned, right end pinned
Since dHA ¼ 0 and MA ¼ 0; HA ¼
LPH AHH
and
cA ¼ AMH HA LPM
The loading terms are as follows:
Reference no., loading 1a. Concentrated load on the horizontal member
Loading terms
[CHAP. 8
Wa a2 LPH ¼ 3l1 a 2l1 l3 l2 l3 ðl1 l2 Þ 6E3 I3 l3 Wa a2 LPM ¼ 3a 2l3 6E3 I3 l3
TABLE 8.2
Reaction and deflection formulas for in-plane loading of elastic frames (Continued)
wa l33 ðw wa Þl33 ðl þ l2 Þ b ð7l1 þ 8l2 Þ 24E3 I3 1 360E3 I3
7wa l33 11ðwb wa Þl33 72E3 I3 180E3 I3 Mo 3a2 ¼ 6l1 a 2l1 l3 l2 l3 ðl l2 Þ 6E3 I3 l3 1 Mo 3a2 ¼ 4a 2l3 6E3 I3 l3 a ¼ yo l1 ðl1 l2 Þ l3 2 a ¼ yo 3 l3
LPM ¼ 1c. Concentrated moment on the horizontal member
LPH LPM
1d. Concentrated angular displacement on the horizontal member
1e. Concentrated laternal displacement on the horizontal member
1g. Distributed load on the left vertical member
LPM
LPH ¼
Do ðl1 l2 Þ l3
LPM ¼
Do l3
LPH ¼ W AHH aAHM þ LPM ¼ W AMH aAMM þ
a3 6E1 I1
a2 2E1 I1
l2 l41 l l2 l41 þ ðwb wa Þ AHH 1 AHM 1 þ LPH ¼ wa AHH l1 AHM 1 þ 2 24E1 I1 2 3 30E1 I1 3 l1 l l l31 l l þ 1 3 ðl þ l2 Þ þ ðwb wa Þ þ 1 3 ð2l þ 3l2 Þ LPM ¼ wa 6E1 I1 6E3 I3 1 24E1 I1 36E3 I3 1
1h. Concentrated moment on the left vertical member
ðNote: Do could also be an increase in the length l1 or a decrease in the length l2 Þ
a2 AHM 2E1 I1 a ¼ Mo AMM E 1 I1
LPH ¼ Mo LPM
Beams; Flexure of Straight Bars
1f. Concentrated load on the left vertical member
LPH
8.17]
LPH ¼
SEC.
1b. Distributed load on the horizontal member
203
Reaction and deflection formulas for in-plane loading of elastic frames (Continued)
Reference no., loading
1j. Concentrated lateral displacement on the left vertical member
Loading terms LPH ¼ yo ðaÞ LPM ¼ yo ð1Þ
LPH ¼ Do ð1Þ
ðNote: Do could also be a decrease in the length l3 Þ
LPM ¼ 0
1k. Concentrated load on the right vertical member
1l. Distributed load on the right vertical member
1m. Concentrated moment on the right vertical member
1n. Concentrated angular displacement on the right vertical member
1p. Concentrated lateral displacement on the right vertical member
1 l ð3l a2 2l32 a3 Þ 3 ðl2 aÞðl1 þ 2l2 Þ 6E2 I2 2 6E3 I3 l3 ¼W ðl aÞ 6E3 I3 2 5l24 l2 l 3l42 l2 l ¼ wa 2 3 ðl þ 2l2 Þ þ ðwb wa Þ 2 3 ðl þ 2l2 Þ 24E2 I2 12E3 I3 1 40E2 I2 36E3 I3 1 2 2 l2 l3 l2 l3 ¼ wa þ ðwb wa Þ 12E3 I3 36E3 I3 a l ¼ Mo ð2l aÞ þ 3 ðl1 þ 2l2 Þ 6E3 I3 2E2 I2 2
LPH ¼ W LPM LPH LPM LPH
LPM ¼ Mo
Formulas for Stress and Strain
1i. Concentrated angular displacement on the left vertical member
204
TABLE 8.2
l3 6E3 I3
LPH ¼ yo ðl2 aÞ LPM ¼ 0
LPH ¼ Do ð1Þ
ðNote: Do could also be an increase in the length l3 Þ
LPM ¼ 0
[CHAP. 8
TABLE 8.2
Reaction and deflection formulas for in-plane loading of elastic frames (Continued)
1r. Uniform temperature differential from outside to inside. Average temperature is To 2. Left and guided horizontally, right end pinned
ðT1 T2 Þ g1 l21 g2 l22 g3 l3 ðl1 þ l2 Þ þ þ 2 t3 t1 t2 ðT T2 Þ 4g1 l1 g3 l3 ¼ 1 þ 2 t1 3t3
LPH ¼ LPM
g ¼ temperature coefficient of expansion ðunit strain=degreeÞ
8.17]
T ¼ uniform temperature To ¼ unloaded temperature
ðl l2 Þ LPH ¼ ðT To Þ g3 l3 1 ðg1 l1 g2 l2 Þ l3 1 ðg1 l1 g2 l2 Þ LPM ¼ ðT To Þ l3
SEC.
1q. Uniform temperature rise:
t1 ; t2 ; and t3 are beam thicknesses from inside to outside
Since cA ¼ 0 and HA ¼ 0
MA ¼
LPM AMM
and
dHA ¼ AHM MA LPH
Use the loading terms for cases 1a to 1r
Since HA and MA are both zero, this is a statically determinate case
4. Left end fixed, right end pinned
Since dHA ¼ 0 and cA ¼ 0,
dHA ¼ LPH
and cA ¼ LPM
Use the loading terms for cases 1a to 1r
HA ¼ Use the loading terms for cases 1a to 1r
AMM LPH AHM LPM AHH AMM ðAHM Þ2
and
MA ¼
AHH LPM AHM LPH AHH AMM ðAHM Þ2
Beams; Flexure of Straight Bars
3. Left end roller supported along the horizontal, right end pinned
205
TABLE 8.2
Reaction and deflection formulas for in-plane loading of elastic frames (Continued)
Deformation equations: Horizontal deflection at A ¼ dHA ¼ CHH HA þ CHV VA þ CHM MA LFH
Angular rotation at A ¼ cA ¼ CMH HA þ CMV VA þ CMM MA LFM where CHH ¼
l31 l3 ðl1 l2 Þ3 l21 l3 þ 1 þ 3E1 I1 3E2 I2 E3 l3
CHV ¼ CVH ¼
l2 l3 l l2 ð2l l2 Þ þ 1 3 2E2 I2 1 2E3 I3
CHM ¼ CMH ¼
l21 l l l þ 2 ð2l l2 Þ þ 1 3 2E1 I1 2E2 I2 1 E3 I3
CVV ¼
l2 l23 l3 þ 3 E2 I2 3E3 I3
CVM ¼ CMV ¼ CMM ¼
l2 l3 l2 þ 3 E2 I2 2E3 I3
Formulas for Stress and Strain
Vertical deflection at A ¼ dVA ¼ CVH HA þ CVV VA þ CVM MA LFV
206
General reaction and deformation expressions for cases 5–12, right end fixed in all eight cases:
l1 l l þ 2 þ 3 E1 I1 E2 I2 E3 l3
and where LFH , LFV , and LFM are loading terms given below for several types of load (Note: If desired, HB , VB , and MB are to be evaluated from equilibrium equations after calculating HA , VA , and MA ) 5. Left end fixed, right end fixed
Since dHA ¼ 0, dVA ¼ 0, and cA ¼ 0, these three equations are solved simultaneously for HA, VA , and MA :
CHH HA þ CHV VA þ CHM MA ¼ LFH CVH HA þ CVV VA þ CVM MA ¼ LFV CMH HA þ CMV VA þ CMM MA ¼ LFM The loading terms are given below. Reference no., loading l2 l ð2l l2 Þðl3 aÞ þ 1 ðl3 aÞ2 2E2 I2 1 2E3 I3 a3 LFV ¼ W CVV aCVM þ 6E3 I3 l2 1 LFM ¼ W ðl3 aÞ þ ðl3 aÞ2 2E3 I3 E2 I2
LFH ¼ W
[CHAP. 8
5a. Concentrated load on the horizontal member
Loading terms
TABLE 8.2
Reaction and deflection formulas for in-plane loading of elastic frames (Continued)
5d. Concentrated angular displacement on the horizontal member
8.17]
5c. Concentrated moment on the horizontal member
l2 l23 l l3 l2 l23 l l3 ð2l1 l2 Þ þ 1 3 þ ðwb wa Þ ð2l1 l2 Þ þ 1 3 4E2 I2 6E3 I3 12E2 I2 24E3 I3 l2 l33 l2 l33 l43 l43 þ ðwb wa Þ þ þ LFV ¼ wa 2E2 I2 8E3 I3 6E2 I2 30E3 I3 3 2 2 l2 l3 l l2 l3 l33 þ 3 þ LFM ¼ wa þ ðwb wa Þ 2E2 I2 6E3 I3 6E2 I2 24E3 I3 l2 l1 LFH ¼ Mo ð2l l2 Þ ðl aÞ 2E2 I2 1 E3 I3 3 a2 LFV ¼ Mo CVM þ 2E3 I3 l2 1 LFM ¼ Mo ðl aÞ E2 I2 E3 I3 3 LFH ¼ wa
SEC.
5b. Distributed load on the horizontal member
LFH ¼ yo ðl1 Þ e
LFV ¼ yo ðaÞ LFM ¼ yo ð1Þ
LFH ¼ 0 LFV ¼ Do ð1Þ LFM ¼ 0
5f. Concentrated load on the left vertical member
LFH ¼ W CHH aCHM þ LFV ¼ W ðCVH aCVM Þ LFM ¼ W CMH aCMM þ
5g. Distributed load on the left vertical member
a3 6E1 I1
a2 2E1 I1
207
l2 l41 l l2 l41 LFH ¼ wa CHH l1 CHM 1 þ þ ðwb wa Þ CHH 1 CHM 1 þ 2 24E1 I1 2 3 30E1 I1 l2 l l2 LFV ¼ wa CVH l1 CVM 1 þ ðwb wa Þ CVH 1 CVM 1 2 2 3 l2 l3 l l2 l3 LFM ¼ wa CMH l1 CMM 1 þ 1 þ ðwb wa Þ CMH 1 CMM 1 þ 1 2 6E1 I1 2 3 8E1 I1
Beams; Flexure of Straight Bars
5e. Concentrated lateral displacement on the horizontal member
TABLE 8.2
Reaction and deflection formulas for in-plane loading of elastic frames (Continued)
LFH
a2 2E1 I1
LFV ¼ Mo ðCVM Þ a LFM ¼ Mo CMM þ E 1 I1 5i. Concentrated angular displacement on the left vertical member
LFH ¼ yo ðaÞ LFV ¼ 0 LFM ¼ yo ð1Þ
5j. Concentrated lateral displacement on the left vertical member
LFH ¼ Do ð1Þ LFV ¼ 0 LFM ¼ 0
5k. Concentrated load on the right vertical member
LFH ¼
W ½3l ðl aÞ2 2l32 a3 þ 3al22 6E2 I2 1 2
LFV ¼
W ½l ðl aÞ2 2E2 I2 3 2
Formulas for Stress and Strain
5h. Concentrated moment on the left vertical member
Loading terms ¼ Mo CHM þ
208
Reference no., loading
W ðl aÞ2 2E2 I2 2 l32 l32 ¼ wa ð4l1 3l2 Þ þ ðwb wa Þ ð5l1 4l2 Þ 24E2 I2 120E2 I2
LFM ¼ 5l. Distributed load on the right vertical member
LFV ¼ wa
l32 l3 l3 l þ ðwb wa Þ 2 3 6E2 I2 24E2 I2
LfM ¼ wa
l32 l32 þ ðwb wa Þ 6E2 I2 24E2 I2
LFH ¼
Mo ½2l1 ðl2 aÞ a2 þ l22 2E2 I2
LFV ¼
Mo ½l3 ðl2 aÞ E2 I2
LFM ¼
Mo ½ðl2 aÞ E2 I2
[CHAP. 8
5m. Concentrated moment on the right vertical member
LFH
TABLE 8.2
Reaction and deflection formulas for in-plane loading of elastic frames (Continued) SEC.
LFH ¼ yo ðl1 aÞ
8.17]
5n. Concentrated angular displacement on the right vertical member
LFV ¼ yo ðl3 Þ LFM ¼ yo ð1Þ
5p. Concentrated lateral displacement on the right vertical member
LFH ¼ Do ð1Þ
ðNote: Do could also be an increase in the length l3 Þ
LFV ¼ 0 LFM ¼ 0
5q. Uniform temperature rise: T ¼ uniform temperature To ¼ unloaded temperature
5r. Uniform temperature differential from outside to inside; average temperature is To
g ¼ temperature coefficient of expansion ðinches=inch=degreeÞ
LFV ¼ ðT To Þðg1 l1 g2 l2 Þ LFM ¼ 0 2 l g l g l l g LFH ¼ ðT1 T2 Þ 1 1 þ 2 2 ð2l1 l2 Þ þ 1 3 3 2t1 2t2 t3 l l g l2 g LFV ¼ ðT1 T2 Þ 2 3 2 þ 3 3 t1 ; t2 ; and t3 are beam thicknesses from inside to outside t2 2t3 l g l g l g LFM ¼ ðT1 T2 Þ 1 1 þ 2 2 þ 3 3 t1 t2 t3 Since dHA ¼ 0; dVA ¼ 0 and MA ¼ 0, HA ¼
LFH CVV LFV CHV
VA ¼
CHH CVV ðCHV Þ2
LFV CHH LFH CHV CHH CVV ðCHV Þ2
cA ¼ CMH HA þ CMV VA LFM Use the loading terms for cases 5a to 5r
7. Left end guided horizontally, right end fixed
Since dVA ¼ 0; cA ¼ 0 and HA ¼ 0, VA ¼
LFV CMM LFM CVM CVV CMM ðCVM Þ2
MA ¼
LFM CVV LFV CVM CVV CMM ðCVM Þ2
Beams; Flexure of Straight Bars
6. Left end pinned, right end fixed
LFH ¼ ðT To Þðg3 l3 Þ
dHA ¼ CHV VA þ CHM MA LFH
209
Use the loading terms for cases 5a to 5r
210
TABLE 8.2
Reaction and deflection formulas for in-plane loading of elastic frames (Continued) Since dHA ¼ 0; cA ¼ 0, and VA ¼ 0, HA ¼
LFH CMM LFM CHM CHH CMM ðCHM Þ2
MA ¼
LFM CHH LFH CHM CHH CMM ðCHM Þ2
dVA ¼ CVH HA þ CVM MA LFV Use the loading terms for cases 5a to 5r 9. Left end roller supported along the horizontal, right end fixed
Since dVA ¼ 0; HA ¼ 0, and MA ¼ 0, VA ¼
LFV CVV
dHA ¼ CHV VA LFH
and
cA ¼ CMV VA LFM
dVA ¼ CVH HA LFV
and
cA ¼ CMH HA LFM
dHA ¼ CHM MA LFH
and
dVA ¼ CVM MA LFV
Use the loading terms for cases 5a to 5r
10. Left end roller supported along the vertical, right end fixed
Since dHA ¼ 0; VA ¼ 0, and MA ¼ 0, HA ¼
LFH CHH
Formulas for Stress and Strain
8. Left end guided vertically, right end fixed
Use the loading terms for cases 5a to 5r 11. Left end guided by moment only (zero slope at the left end), right end fixed
Since cA ¼ 0; HA ¼ 0, and VA ¼ 0, MA ¼
LFM CMM
Use the loading terms for cases 5a to 5r 12. Left end free, right end fixed
Since HA ¼ 0; VA ¼ 0 and MA ¼ 0, this is a statically determinate case. The deflections are given by dHA ¼ LFH
dVA ¼ LFV
and
cA ¼ LFM
Use the loading terms for cases 5a to 5r
[CHAP. 8
SEC.
8.17]
Beams; Flexure of Straight Bars TABLE 8.3
bx
Numerical values for functions used in Table 8.5 F1
F2
F3
F4
0.00 0.10 0.20 0.30 0.40
1.00000 0.99998 0.99973 0.99865 0.99573
0.00000 0.20000 0.39998 0.59984 0.79932
0.00000 0.01000 0.04000 0.08999 0.15995
0.00000 0.00067 0.00533 0.01800 0.04266
0.50 0.60 0.70 0.80 0.90
0.98958 0.97841 0.96001 0.93180 0.89082
0.99792 1.19482 1.38880 1.57817 1.76067
0.24983 0.35948 0.48869 0.63709 0.80410
0.08331 0.14391 0.22841 0.34067 0.48448
1.00 1.10 1.20 1.30 1.40
0.83373 0.75683 0.65611 0.52722 0.36558
1.93342 2.09284 2.23457 2.35341 2.44327
0.98890 1.19034 1.40688 1.63649 1.87659
0.66349 0.88115 1.14064 1.44478 1.79593
1.50 1.60 1.70 1.80 1.90
0.16640 0.07526 0.36441 0.70602 1.10492
2.49714 2.50700 2.46387 2.35774 2.17764
2.12395 2.37456 2.62358 2.86523 3.09266
2.19590 2.64573 3.14562 3.69467 4.29076
2.00 2.10 2.20 2.30 2.40
1.56563 2.09224 2.68822 3.35618 4.09766
1.91165 1.54699 1.07013 0.46690 0.27725
3.29789 3.47170 3.60355 3.68152 3.69224
4.93026 5.60783 6.31615 7.04566 7.78428
2.50 2.60 2.70 2.80 2.90
4.91284 5.80028 6.75655 7.77591 8.84988
1.17708 2.24721 3.50179 4.95404 6.61580
3.62088 3.45114 3.16529 2.74420 2.16749
8.51709 9.22607 9.88981 10.48317 10.97711
3.00 3.20 3.40 3.60 3.80
9.96691 12.26569 14.50075 16.42214 17.68744
8.49687 12.94222 18.30128 24.50142 31.35198
1.41372 0.71484 3.82427 8.09169 13.66854
11.33837 11.50778 10.63569 8.29386 3.98752
4.00 4.20 4.40 4.60 4.80
17.84985 16.35052 12.51815 5.57927 5.31638
38.50482 45.41080 51.27463 55.01147 55.21063
20.65308 29.05456 38.74857 49.42334 60.51809
2.82906 12.72446 26.24587 43.85518 65.84195
5.00 5.20 5.40 5.60 5.80
21.05056 42.46583 70.26397 104.86818 146.24469
50.11308 37.61210 15.28815 19.50856 69.51236
71.15526 80.07047 85.54576 85.35442 76.72824
92.21037 122.53858 155.81036 190.22206 222.97166
6.00
193.68136
137.31651
56.36178
250.04146
211
212
[CHAP. 8
Formulas for Stress and Strain
TABLE 8.4
Numerical values for denominators used in Table 8.5
bl
C11
C12
C13
C14
0.00 0.10 0.20 0.30 0.40
0.00000 0.00007 0.00107 0.00540 0.01707
0.00000 0.20000 0.40009 0.60065 0.80273
0.00000 0.00133 0.01067 0.03601 0.08538
0.00000 0.02000 0.08001 0.18006 0.32036
0.50 0.60 0.70 0.80 0.90
0.04169 0.08651 0.16043 0.27413 0.44014
1.00834 1.22075 1.44488 1.68757 1.95801
0.16687 0.28871 0.45943 0.68800 0.98416
0.50139 0.72415 0.99047 1.30333 1.66734
1.00 1.10 1.20 1.30 1.40
0.67302 0.98970 1.40978 1.95606 2.65525
2.26808 2.63280 3.07085 3.60512 4.26345
1.35878 1.82430 2.39538 3.08962 3.92847
2.08917 2.57820 3.14717 3.81295 4.59748
1.50 1.60 1.70 1.80 1.90
3.53884 4.64418 6.01597 7.70801 9.78541
5.07950 6.09376 7.35491 8.92147 10.86378
4.93838 6.15213 7.61045 9.36399 11.47563
5.52883 6.64247 7.98277 9.60477 11.57637
2.00 2.10 2.20 2.30 2.40
12.32730 15.43020 19.21212 23.81752 29.42341
13.26656 16.23205 19.88385 24.37172 29.87747
14.02336 17.10362 20.83545 25.36541 30.87363
13.98094 16.92046 20.51946 24.92967 30.33592
2.50 2.60 2.70 2.80 2.90
36.24681 44.55370 54.67008 66.99532 82.01842
36.62215 44.87496 54.96410 67.29005 82.34184
37.58107 45.75841 55.73686 67.92132 82.80645
36.96315 45.08519 55.03539 67.21975 82.13290
3.00 3.20 3.40 3.60 3.80
100.33792 149.95828 223.89682 334.16210 498.67478
100.71688 150.51913 224.70862 335.25438 500.03286
100.99630 150.40258 224.21451 334.46072 499.06494
100.37775 149.96510 224.02742 334.55375 499.42352
4.00 4.20 4.40 4.60 4.80
744.16690 1110.50726 1657.15569 2472.79511 3689.70336
745.73416 1112.19410 1658.85362 2474.39393 3691.10851
744.74480 1111.33950 1658.26871 2474.17104 3691.28284
745.31240 1112.02655 1658.96679 2474.76996 3691.68805
5.00 5.20 5.40 5.60 5.80
5505.19766 8213.62683 12254.10422 18281.71463 27273.73722
5506.34516 8214.49339 12254.71090 18282.12354 27274.04166
5506.88918 8215.32122 12255.69184 18283.10271 27274.86449
5507.03673 8215.18781 12255.29854 18282.51163 27274.16893
6.00
40688.12376
40688.43354
40688.97011
40688.27990
NOTATION:
Shear, moment, slope, and deflection formulas for finite-length beams on elastic foundations
concentrated lateral displacement (length); g ¼ temperature coefficient of expansion (unit strain per degree); T1 and T2 ¼ temperatures on top and bottom surfaces, respectively (degrees). RA and RB are the vertical end reactions at the left and right, respectively, and are positive upward. MA and MB are the reaction end moments at the left and right, respectively, and all moments are positive
8.17]
W ¼ load (force); w ¼ unit load (force per unit length); Mo ¼ applied couple (force-length); yo ¼ externally created concentrated angular displacement (radians); Do ¼ externally created
SEC.
TABLE 8.5
when producing compression on the upper portion of the beam cross section. The transverse shear force V is positive when acting upward on the left end of a portion of the beam. All applied loads, couples, and displacements are positive as shown. All slopes are in radians, and all temperatures are in degrees. All deflections are positive upward and slopes positive when up and to the right. Note that MA and RA are reactions, not applied loads. They exist only when necessary end restraints are provided. The following constants and functions, involving both beam constants and foundation constants, are hereby defined in order to permit condensing the tabulated formulas which follow ko ¼ foundation modulus (unit stress per unit deflection); bo ¼ beam width; and b ¼ ðbo ko =4EIÞ1=4 . (Note: See page 131 for a definition of hx ain :Þ The functions cosh bhx ai; sinh bhx ai, cos bhx ai, and sin bhx ai are also defined as having a value of zero if x < a. F1 F2 F3 F4
¼ hx ai0 cosh bhx aicos bhx ai ¼ cosh bhx aisin bhx ai þ sinh bhx aicos bhx ai ¼ sinh bhx aisin bhx ai ¼ cosh bhx aisin bhx ai sinh bhx aicos bhx ai
Fa5 ¼ hx ai0 Fa1 Fa6 ¼ 2bðx aÞhx ai0 Fa2 1. Concentrated intermediate load
C1 C2 C3 C4 Ca1
¼ cosh bl cos bl ¼ cosh bl sin bl þ sinh bl cos bl ¼ sinh bl sin bl ¼ cosh bl sin bl sinh bl cos bl ¼ cosh bðl aÞ cos bðl aÞ
Ca2 Ca3 Ca4 Ca5 Ca6
¼ cosh bðl aÞ sin bðl aÞ þ sinh bðl aÞ cos bðl aÞ ¼ sinh bðl aÞ sin bðl aÞ ¼ cosh bðl aÞ sin bðl aÞ sinh bðl aÞ cos bðl aÞ ¼ 1 Ca1 ¼ 2bðl aÞ Ca2
C11 ¼ sinh2 bl sin2 bl C12 ¼ cosh bl sinh bl þ cos bl sin bl C13 ¼ cosh bl sinh bl cos bl sin bl C14 ¼ sinh2 bl þ sin2 bl
Transverse shear ¼ V ¼ RA F1 yA 2EIb3 F2 yA 2EIb2 F3 MA bF4 WFa1 Bending moment ¼ M ¼ MA F1 þ Slope ¼ y ¼ yA F1 þ
RA W F yA 2EIb2 F3 yA EIbF4 Fa2 2b 2b 2
MA RA W F þ F yA bF4 Fa3 2EIb 2 2EIb2 3 2EIb2
Deflection ¼ y ¼ yA F1 þ
yA MA RA W F þ F F F þ 2b 2 2EIb2 3 4EIb3 4 4EIb3 a4
If bl > 6, see Table 8.6 Expressions for RA, MA , yA , and yA are found below for several combinations of end restraints
Beams; Flexure of Straight Bars
Fa1 Fa2 Fa3 Fa4
¼ cosh bx cos bx ¼ cosh bx sin bx þ sinh bx cos bx ¼ sinh bx sin bx ¼ cosh bx sin bx sinh bx cos bx
213
214
Shear, moment, slope, and deflection formulas for finite-length beams on elastic foundations (Continued)
Right Free
end Left end
RA ¼ 0
Free
yA ¼ yA ¼
MA ¼ 0
W C2 Ca2 2C3 Ca1 C11 2EIb2 W
Guided Simply supported
W 2EIb2
yA ¼ 0 Fixed
yA ¼ 0
C C C4 Ca1 RA ¼ W 3 a2 C13 yA ¼
C1 Ca2 C2 Ca1 C13
yA ¼ 0
2C1 Ca1 þ C4 Ca2 RA ¼ W 2 þ C11 MA ¼
W C1 Ca1 þ C3 Ca3 C12
yA ¼
RA ¼ 0
W 2C1 Ca1 þ C4 Ca2 C12
MA ¼ 0
yA ¼
yA ¼ 0
4EIb3
W C1 Ca2 C2 Ca1 2 þ C11 b
2EIb3
yA ¼ 0
W C2 Ca3 C4 Ca1 MA ¼ C14 2b yA ¼
W C2 Ca1 þ C4 Ca3 C14
4EIb3
MA ¼ 0
yA ¼ 0
C C þ C3 Ca3 RA ¼ W 1 a1 1 þ C11 yA ¼
W C1 Ca3 C3 Ca1 1 þ C11 2EIb2
yA ¼ 0
yA ¼ 0
C C þ C2 Ca1 RA ¼ W 4 a3 C12 MA ¼
Simply supported RA ¼ 0
W C2 Ca3 C4 Ca1 C12 2EIb2
yA ¼
W C2 Ca2 2C3 Ca1 MA ¼ C12 2b yA ¼
yA ¼
MA ¼ 0
C4 Ca1 C3 Ca2 C11
2EIb3
RA ¼ 0
Guided RA ¼ 0
W C1 Ca3 C3 Ca1 C12 b
MA ¼ 0
W C1 Ca2 þ C3 Ca4 C13 2EIb2
yA ¼
W C4 Ca4 þ C2 Ca2 C13
yA ¼
4EIb3
RA ¼ 0
yA ¼ 0
W C1 Ca2 þ C3 Ca4 MA ¼ 1 þ C11 2b yA ¼
W 4EIb3
MA ¼ 0
C1 Ca4 C3 Ca2 1 þ C11
yA ¼ 0
W C2 Ca2 þ C4 Ca4 RA ¼ C14 2 yA ¼
W C2 Ca4 C4 Ca2 C14 4EIb2
yA ¼ 0
yA ¼ 0
C C C1 Ca4 RA ¼ W 3 a2 C13 MA ¼
Fixed RA ¼ 0
W C2 Ca4 C4 Ca2 C13 2b
MA ¼ 0
W 2C1 Ca3 þ C4 Ca4 2 þ C11 2EIb2 W
C1 Ca4 C2 Ca3 2 þ C11
2EIb3
RA ¼ 0
yA ¼ 0
W 2C1 Ca3 þ C4 Ca4 MA ¼ C12 2b yA ¼
W 4EIb3
MA ¼ 0
Formulas for Stress and Strain
TABLE 8.5
C2 Ca4 2C3 Ca3 C12
yA ¼ 0
C C C1 Ca4 RA ¼ W 2 a3 C13 yA ¼
W 2EIb2
yA ¼ 0
C3 Ca4 C4 Ca3 C13
yA ¼ 0
2C3 Ca3 C2 Ca4 RA ¼ W C11 MA ¼
W C3 Ca4 C4 Ca3 C11 b
[CHAP. 8
TABLE 8.5
Shear, moment, slope, and deflection formulas for finite-length beams on elastic foundations (Continued)
2. Partial uniformly distributed load
Transverse shear ¼ V ¼ RA F1 yA 2EIb3 F2 yA 2EIb2 F3 MA bF4
RA w F yA 2EIb2 F3 yA EIbF4 2 Fa3 2b 2 2b
8.17]
Slope ¼ y ¼ yA F1 þ
SEC.
Bending moment ¼ M ¼ MA F1 þ
w F 2b a2
MA RA w F þ F yA bF4 Fa4 2EIb 2 2EIb2 3 4EIb3
Deflection ¼ y ¼ yA F1 þ
yA MA RA w F þ F þ F F 2b 2 2EIb2 3 4EIb3 4 4EIb4 a5
If bl > 6, see Table 8.6 Expressions for RA, MA , yA , and yA are found below for several combinations of end restraints Right Free
end
Free
Left end
RA ¼ 0
MA ¼ 0
MA ¼ 0
Fixed RA ¼ 0
MA ¼ 0
yA ¼
w C2 Ca4 C4 Ca2 C12 4EIb3
yA ¼
w C1 Ca3 þ C3 Ca5 C13 2EIb3
yA ¼
w C1 Ca4 þ C4 Ca5 2 þ C11 2EIb3
yA ¼
w C4 Ca2 2C3 Ca3 C11 4EIb4
yA ¼
w C1 Ca2 þ C3 Ca4 C12 4EIb4
yA ¼
w C4 Ca5 þ C2 Ca3 C13 4EIb4
yA ¼
w 2C1 Ca5 C2 Ca4 2 þ C11 4EIb4
yA ¼ 0
w C C C3 Ca2 MA ¼ 2 2 a3 C12 2b w C1 Ca2 þ C4 Ca3 C12 4EIb4
MA ¼ 0
yA ¼ 0
w 2C2 Ca3 C4 Ca2 RA ¼ 2b C13 yA ¼
w 2C1 Ca3 C2 Ca2 C13 4EIb3
yA ¼ 0
yA ¼ 0
w C1 Ca2 þ C4 Ca3 RA ¼ b 2 þ C11 w 2C1 Ca3 C2 Ca2 2 þ C11
2b2
yA ¼ 0
w C C C4 Ca2 MA ¼ 2 2 a4 C14 4b yA ¼
w C2 Ca2 þ C4 Ca4 C14 8EIb4
MA ¼ 0
yA ¼ 0
w C1 Ca2 þ C3 Ca4 RA ¼ 2b 1 þ C11 yA ¼
w 4EIb3
yA ¼ 0
C1 Ca4 C3 Ca2 1 þ C11
yA ¼ 0
w C4 Ca4 þ C2 Ca2 RA ¼ 2b C12 MA ¼
w C1 Ca4 C3 Ca2 C12
2b2
RA ¼ 0
yA ¼ 0
w C C þ C3 Ca5 MA ¼ 2 1 a3 1 þ C11 2b yA ¼
w C1 Ca5 C3 Ca3 1 þ C11 4EIb4
MA ¼ 0
yA ¼ 0
w C2 Ca3 þ C4 Ca5 RA ¼ 2b C14 yA ¼
w 4EIb3
yA ¼ 0
C2 Ca5 C4 Ca3 C14
yA ¼ 0
w C3 Ca3 C1 Ca5 RA ¼ b C13 MA ¼
w C2 Ca5 C4 Ca3 C13 2b2
RA ¼ 0
yA ¼ 0
w C C þ C4 Ca5 MA ¼ 2 1 a4 C12 2b yA ¼
w C2 Ca5 C3 Ca4 C12 4EIb4
MA ¼ 0
yA ¼ 0
w C2 Ca4 2C1 Ca5 RA ¼ 2b C13 yA ¼
w 2C3 Ca5 C4 Ca4 C13 4EIb3
yA ¼ 0
yA ¼ 0
w C3 Ca4 C2 Ca5 RA ¼ b C11 MA ¼
w 2C3 Ca5 C4 Ca4 C11
2b2
215
MA ¼
RA ¼ 0
Beams; Flexure of Straight Bars
Guided
Simply supported RA ¼ 0
w C2 Ca3 C3 Ca2 C11 2EIb3
yA ¼
Simply supported
MA ¼ 0
yA ¼
RA ¼ 0
Fixed
Guided RA ¼ 0
TABLE 8.5
Shear, moment, slope, and deflection formulas for finite-length beams on elastic foundations (Continued) Transverse shear ¼ V ¼ RA F1 yA 2EIb3 F2 yA 2EIb2 F3 MA bF4 Bending moment ¼ M ¼ MA F1 þ
RA wF F yA 2EIb2 F3 yA EIbF4 3 a4 2b 2 4b ðl aÞ
MA RA wFa5 F þ F yA bF4 2EIb 2 2EIb2 3 4EIb4 ðl aÞ
Deflection ¼ y ¼ yA F1 þ
yA MA RA wFa6 F þ F F þ 2b 2 2EIb2 3 4EIb3 4 8EIb5 ðl aÞ
If bl > 6, see Table 8.6 Expressions for RA, MA , yA , and yA are found below for several combinations of end restraints Right Free
end Left end
RA ¼ 0
Free
yA ¼ yA ¼
RA ¼ 0
wðC2 Ca4 2C3 Ca3 Þ 4EIb4 ðl aÞC11
yA ¼
wðC4 Ca3 C3 Ca4 Þ 4EIb5 ðl aÞC11
Guided
RA ¼ 0 MA ¼
yA ¼ 0
wðC2 Ca4 2C3 Ca3 Þ 4b3 ðl aÞC12
Simply supported
wð2C1 Ca3 þ C4 Ca4 Þ yA ¼ 8EIb5 ðl aÞC12 MA ¼ 0
wðC1 Ca4 C2 Ca3 Þ 4EIb4 ðl aÞC13
yA ¼ 0
yA ¼ 0
wð2C1 Ca3 þ C4 Ca4 Þ RA ¼ 2b2 ðl aÞð2 þ C11 Þ MA ¼
wðC1 Ca4 C2 Ca3 Þ 2b3 ðl aÞð2 þ C11 Þ
yA ¼
RA ¼ 0
wðC2 Ca5 C4 Ca3 Þ 4EIb4 ðl aÞC12 wðC1 Ca3 þ C3 Ca5 Þ 4EIb5 ðl aÞC12
RA ¼ 0 MA ¼
yA ¼ 0
wðC2 Ca5 C4 Ca3 Þ 4b3 ðl aÞC14
wðC2 Ca3 þ C4 Ca5 Þ yA ¼ 8EIb5 ðl aÞC14 MA ¼ 0
yA ¼ 0
wðC C þ C3 Ca5 Þ RA ¼ 2 1 a3 2b ðl aÞð1 þ C11 Þ yA ¼
wðC1 Ca5 C3 Ca3 Þ 4EIb4 ðl aÞð1 þ C11 Þ
yA ¼ 0
yA ¼ 0
wðC4 Ca5 þ C2 Ca3 Þ RA ¼ 2b2 ðl aÞC12 MA ¼
Simply supported
MA ¼ 0
wðC1 Ca5 C3 Ca3 Þ 2b3 ðl aÞC12
Fixed
MA ¼ 0
RA ¼ 0
yA ¼
wðC1 Ca4 þ C3 Ca6 Þ 4EIb4 ðl aÞC13
yA ¼
yA ¼
wðC2 Ca4 þ C4 Ca6 Þ 8EIb5 ðl aÞC13
yA ¼
RA ¼ 0 MA ¼
yA ¼ 0
wðC1 Ca4 þ C3 Ca6 Þ 4b3 ðl aÞð1 þ C11 Þ
wðC1 Ca6 C3 Ca4 Þ yA ¼ 8EIb5 ðl aÞð1 þ C11 Þ MA ¼ 0
yA ¼ 0
wðC2 Ca4 þ C4 Ca6 Þ RA ¼ 4b2 ðl aÞC14 yA ¼
wðC2 Ca6 C4 Ca4 Þ 8EIb4 ðl aÞC14
yA ¼ 0
yA ¼ 0
wðC3 Ca4 C1 Ca6 Þ RA ¼ 2b2 ðl aÞC13 MA ¼
wðC2 Ca6 C4 Ca4 Þ 4b3 ðl aÞC13
MA ¼ 0
wð2C1 Ca5 þ C4 Ca6 Þ 4EIb4 ðl aÞð2 þ C11 Þ wðC1 Ca6 C2 Ca5 Þ 4EIb5 ðl aÞð2 þ C11 Þ
RA ¼ 0 MA ¼
yA ¼ 0
wð2C1 Ca5 þ C4 Ca6 Þ 4b3 ðl aÞC12
wðC2 Ca6 2C3 Ca5 Þ yA ¼ 8EIb5 ðl aÞC12 MA ¼ 0
yA ¼ 0
wðC2 Ca5 C1 Ca6 Þ RA ¼ 2b2 ðl aÞC13 yA ¼
wðC3 Ca6 C4 Ca5 Þ 4EIb4 ðl aÞC13
yA ¼ 0
yA ¼ 0
wð2C3 Ca5 C2 Ca6 Þ RA ¼ 2b2 ðl aÞC11 MA ¼
wðC3 Ca6 C4 Ca5 Þ 2b3 ðl aÞC11
[CHAP. 8
Fixed
yA ¼ 0
wðC3 Ca4 C4 Ca3 Þ RA ¼ 2b2 ðl aÞC13 yA ¼
Guided
MA ¼ 0
Formulas for Stress and Strain
Slope ¼ y ¼ yA F1 þ
wFa3 2b2 ðl aÞ
216
3. Partial uniformly increasing load
TABLE 8.5
Shear, moment, slope, and deflection formulas for finite-length beams on elastic foundations (Continued) Transverse shear ¼ V ¼ RA F1 yA 2EIb3 F2 yA 2EIb2 F3 MA bF4 Mo bFa4
Slope ¼ y ¼ yA F1 þ
RA F yA 2EIb2 F3 yA EIbF4 þ Mo Fa1 2b 2
8.17]
Bending moment ¼ M ¼ MA F1 þ
SEC.
4. Concentrated intermediate moment
MA RA Mo F þ F F yA bF4 þ 2EIb 2 2EIb2 3 2EIb a2
Deflection ¼ y ¼ yA F1 þ
yA MA RA Mo F þ F þ F þ F 2b 2 2EIb2 3 4EIb3 4 2EIb2 a3
If bl > 6, see Table 8.6 Expressions for RA, MA , yA , and yA are found below for several combinations of end restraints Right Free
end
Free
Left end
RA ¼ 0 yA ¼
Mo C3 Ca4 þ C2 Ca1 EIb C11
yA ¼
Mo C2 Ca2 þ C4 Ca4 2EIb C12
yA ¼
yA ¼
Mo 2C3 Ca1 þ C4 Ca4 C11 2EIb2
yA ¼
Mo C3 Ca2 C1 Ca4 C12 2EIb2
yA ¼
Guided Simply supported
yA ¼
Mo C1 Ca4 C4 Ca1 C12 2EIb2
MA ¼ 0
yA ¼ 0
2C C þ C4 Ca4 RA ¼ Mo b 3 a1 C13 yA ¼
Mo 2C1 Ca1 þ C2 Ca4 2EIb C13
yA ¼ 0
yA ¼ 0
C C C1 Ca4 RA ¼ Mo 2b 4 a1 2 þ C11 2C1 Ca1 þ C2 Ca4 2 þ C11
yA ¼ 0
Mo C2 Ca2 þ C4 Ca4 MA ¼ 2 C14 yA ¼
Mo C4 Ca2 C2 Ca4 C14 4EIb2
MA ¼ 0
yA ¼ 0
C C C1 Ca4 RA ¼ Mo b 3 a2 1 þ C11 yA ¼
Mo C1 Ca2 þ C3 Ca4 2EIb 1 þ C11
yA ¼ 0
yA ¼ 0
C C C2 Ca4 RA ¼ Mo b 4 a2 C12 MA ¼ Mo
C1 Ca2 þ C3 Ca4 C12
RA ¼ 0
Mo C1 Ca1 þ C3 Ca3 EIb C13
yA ¼
Mo C1 Ca2 þ C4 Ca3 EIb 2 þ C11
yA ¼
Mo 2C1 Ca3 C2 Ca2 2 þ C11 2EIb2
Mo C4 Ca3 þ C2 Ca1 C13
2EIb2
RA ¼ 0
yA ¼ 0
C C þ C3 Ca3 MA ¼ Mo 1 a1 1 þ C11 yA ¼
Mo C3 Ca1 C1 Ca3 1 þ C11 2EIb2
MA ¼ 0
yA ¼ 0
C C þ C4 Ca3 RA ¼ Mo b 2 a1 C14 yA ¼
Fixed
MA ¼ 0
Mo C2 Ca3 C4 Ca1 2EIb C14
yA ¼ 0
yA ¼ 0
C C C1 Ca3 RA ¼ Mo 2b 3 a1 C13 MA ¼ Mo
C2 Ca3 C4 Ca1 C13
RA ¼ 0
MA ¼ 0
yA ¼ 0
C C þ C4 Ca3 MA ¼ Mo 1 a2 C12 yA ¼
Mo C3 Ca2 C2 Ca3 C12 2EIb2
MA ¼ 0
yA ¼ 0
RA ¼ Mo b yA ¼
C2 Ca2 2C1 Ca3 C13
Mo 2C3 Ca3 C4 Ca2 2EIb C13
yA ¼ 0
yA ¼ 0
RA ¼ Mo 2b MA ¼ Mo
C3 Ca2 C2 Ca3 C11
2C3 Ca3 C4 Ca2 C11
217
MA ¼ Mo
RA ¼ 0
RA ¼ 0
Beams; Flexure of Straight Bars
yA ¼ 0
C C þ C3 Ca4 MA ¼ Mo 2 a1 C12
MA ¼ 0
Simply supported
RA ¼ 0
RA ¼ 0
Fixed
Guided
MA ¼ 0
TABLE 8.5
Shear, moment, slope, and deflection formulas for finite-length beams on elastic foundations (Continued) 218
5. Externally created concentrated angular displacement
Transverse shear ¼ V ¼ RA F1 yA 2EIb3 F2 yA 2EIb2 F3 MA bF4 yo 2EIb2 Fa3 Bending moment ¼ M ¼ MA F1 þ
MA RA F þ F yA bF4 þ yo Fa1 2EIb 2 2EIb2 3
Deflection ¼ y ¼ yA F1 þ
yA MA RA y F þ F þ F þ 0F 2b 2 2EIb2 3 4EIb3 4 2b a2
If bl > 6, see Table 8.6 Expressions for RA, MA , yA , and yA are found below for several combinations of end restraints Right Free
end Left end
RA ¼ 0
Free
yA ¼ yo yA ¼
Guided
yA ¼ 0
C C 2C3 Ca3 MA ¼ yo EIb 2 a4 C12 yA ¼
Simply supported
C2 Ca4 2C3 Ca3 C11
yo C4 Ca3 C3 Ca4 b C11
RA ¼ 0
yo 2C1 Ca3 þ C4 Ca4 2b C12
MA ¼ 0
yA ¼ 0
C C C4 Ca3 RA ¼ yo 2EIb 3 a4 C13 2
yA ¼ yo
C1 Ca4 C2 Ca3 C13 yA ¼ 0
2C1 Ca3 þ C4 Ca4 RA ¼ yo 2EIb2 2 þ C11 MA ¼ yo 2EIb
C1 Ca4 C2 Ca3 2 þ C11
Guided RA ¼ 0 yA ¼ yo yA ¼
MA ¼ 0 C2 Ca1 þ C4 Ca3 C12
yo C3 Ca1 C1 Ca3 b C12
RA ¼ 0
yA ¼ 0
C C þ C4 Ca3 MA ¼ yo EIb 2 a1 C14 yA ¼
yo C4 Ca1 C2 Ca3 2b C14
MA ¼ 0
yA ¼ 0
C C C3 Ca1 RA ¼ yo 2EIb 1 a3 1 þ C11 2
yA ¼ yo yA ¼ 0
C1 Ca1 þ C3 Ca3 1 þ C11 yA ¼ 0
C C C4 Ca1 RA ¼ yo 2EIb2 2 a3 C12 MA ¼ yo 2EIb
C1 Ca1 þ C3 Ca3 C12
Simply supported RA ¼ 0
MA ¼ 0
yA ¼ yo
C1 Ca4 C3 Ca2 C13
yA ¼
yo C4 Ca2 C2 Ca4 2b C13
RA ¼ 0
yA ¼ 0
C C C3 Ca2 MA ¼ yo EIb 1 a4 1 þ C11 yA ¼
yo C1 Ca2 þ C3 Ca4 2b 1 þ C11
MA ¼ 0
yA ¼ 0
C C C4 Ca2 RA ¼ yo EIb 2 a4 C14 2
yA ¼
yo C2 Ca2 þ C4 Ca4 2 C14
yA ¼ 0
yA ¼ 0
C C þ C3 Ca4 RA ¼ yo 2EIb2 1 a2 C13 MA ¼ yo EIb
C2 Ca2 þ C4 Ca4 C13
Fixed RA ¼ 0
MA ¼ 0
yA ¼ yo yA ¼
2C1 Ca1 þ C4 Ca2 2 þ C11
yo C1 Ca2 C2 Ca1 b 2 þ C11
RA ¼ 0
yA ¼ 0
MA ¼ yo EIb yA ¼
2C1 Ca1 þ C4 Ca2 C12
yo 2C3 Ca1 C2 Ca2 2b C12
MA ¼ 0
yA ¼ 0
RA ¼ yo 2EIb2 yA ¼ yo yA ¼ 0
C1 Ca2 C2 Ca1 C13
C4 Ca1 C3 Ca2 C13 yA ¼ 0
RA ¼ yo 2EIb2 MA ¼ yo 2EIb
C2 Ca2 2C3 Ca1 C11
C4 Ca1 C3 Ca2 C11
[CHAP. 8
yA ¼ 0 Fixed
MA ¼ 0
Formulas for Stress and Strain
Slope ¼ y ¼ yA F1 þ
RA F yA 2EIb2 F3 yA EIbF4 yo EIbFa4 2b 2
TABLE 8.5
Shear, moment, slope, and deflection formulas for finite-length beams on elastic foundations (Continued) Transverse shear ¼ V ¼ RA F1 yA 2EIb3 F2 yA 2EIb2 F3 MA bF4 Do 2EIb3 Fa2
Slope ¼ y ¼ yA F1 þ
RA F yA 2EIb2 F3 yA EIbF4 Do 2EIb2 Fa3 2b 2
8.17]
Bending moment ¼ M ¼ MA F1 þ
SEC.
6. Externally created concentrated lateral displacement
MA RA F þ F yA bF4 Do bFa4 2EIb 2 2EIb2 3
Deflection ¼ y ¼ yA F1 þ
yA MA RA F þ F þ F þ Do Fa1 2b 2 2EIb2 3 4EIb3 4
If bl > 6, see Table 8.6 Expressions for RA, MA , yA , and yA are found below for several combinations of end restraints Right Free
end
Free
Left end
MA ¼ 0
RA ¼ 0
yA ¼ Do 2b
C2 Ca3 C3 Ca2 C11
yA ¼ Do b yA ¼ Do
yA ¼ Do
Guided
C C C3 Ca2 MA ¼ Do 2EIb2 2 a3 C12 yA ¼ Do
Simply supported
yA ¼ 0
MA ¼ 0
C1 Ca2 þ C4 Ca3 C12 yA ¼ 0
2C3 Ca3 C4 Ca2 RA ¼ Do 2EIb3 C13 yA ¼ Do b yA ¼ 0
2C1 Ca3 C2 Ca2 C13 yA ¼ 0
MA ¼ Do 2EIb2
2C1 Ca3 C2 Ca2 2 þ C11
RA ¼ 0
MA ¼ 0
C2 Ca4 C4 Ca2 C12
yA ¼ Do 2b
C1 Ca3 C3 Ca1 C13
yA ¼ D0 2b
C1 Ca4 C4 Ca1 2 þ C11
C1 Ca2 þ C3 Ca4 C12
yA ¼ Do
yA ¼ 0
C C C4 Ca2 MA ¼ Do EIb2 2 a4 C14 Do C2 Ca2 þ C4 Ca4 2 C14
MA ¼ 0
yA ¼ 0
C C þ C3 Ca4 RA ¼ Do 2EIb3 1 a2 1 þ C11 yA ¼ Do b yA ¼ 0
Fixed
MA ¼ 0
RA ¼ 0
yA ¼
Simply supported RA ¼ 0
C1 Ca4 C3 Ca2 1 þ C11 yA ¼ 0
C C þ C2 Ca2 RA ¼ Do 2EIb3 4 a4 C12 MA ¼ Do 2EIb2
C1 Ca4 C3 Ca2 C12
C4 Ca1 C2 Ca3 C13
RA ¼ 0
yA ¼ 0
C C C3 Ca1 MA ¼ Do 2EIb2 1 a3 1 þ C11 yA ¼ Do
C1 Ca1 þ C3 Ca3 1 þ C11
MA ¼ 0
yA ¼ 0
C C C4 Ca1 RA ¼ Do 2EIb3 2 a3 C14
yA ¼ Do
2C1 Ca1 þ C2 Ca4 2 þ C11
RA ¼ 0
yA ¼ 0
MA ¼ Do 2EIb2 yA ¼ Do
C1 Ca4 C4 Ca1 C12
C2 Ca1 þ C3 Ca4 C12
MA ¼ 0
yA ¼ 0
RA ¼ Do 2EIb3
C2 Ca4 þ 2C1 Ca1 C13
yA ¼ Do b
C2 Ca1 þ C4 Ca3 C14
yA ¼ Do b
2C3 Ca1 þ C4 Ca4 C13
yA ¼ 0
yA ¼ 0
yA ¼ 0
yA ¼ 0
C C þ C1 Ca1 RA ¼ Do 4EIb3 3 a3 C13 MA ¼ Do 2EIb2
C2 Ca1 þ C4 Ca3 C13
RA ¼ Do 4EIb3
C3 Ca4 þ C2 Ca1 C11
MA ¼ Do 2EIb2
2C3 Ca1 þ C4 Ca4 C11
219
C C þ C4 Ca3 RA ¼ Do 4EIb3 1 a2 2 þ C11
MA ¼ 0
Beams; Flexure of Straight Bars
C4 Ca2 2C3 Ca3 C11
RA ¼ 0
Fixed
Guided
RA ¼ 0
TABLE 8.5
Shear, moment, slope, and deflection formulas for finite-length beams on elastic foundations (Continued) Transverse shear ¼ V ¼ RA F1 yA 2EIb3 F2 yA 2EIb2 F3 MA bF4 þ
Slope ¼ y ¼ yA F1 þ
T1 T2 gEIbF4 t
RA T T2 F yA 2EIb2 F3 yA EIbF4 1 gEIðF1 1Þ 2b 2 t
MA RA T T2 F yA bF4 1 F þ gF2 2EIb 2 2EIb2 3 2tb
Deflection ¼ y ¼ yA F1 þ
yA MA RA T T F þ F 1 2 2 gF3 F þ 2b 2 2EIb2 3 4EIb3 4 2tb
If bl > 6, see Table 8.6 Expressions for RA, MA , yA , and yA are found below for several combinations of end restraints Right Free
end
Free
Left end
RA ¼ 0
Guided
Simply supported
MA ¼ 0
RA ¼ 0
MA ¼ 0
Fixed RA ¼ 0
MA ¼ 0
ðT1 T2 Þg C1 C2 þ C3 C4 C2 bt C11
yA ¼
ðT1 T2 Þg C22 þ C42 C12 2bt
yA ¼
ðT1 T2 Þg C12 þ C3 C4 C13 bt
yA ¼
ðT1 T2 Þg C1 C2 þ C3 C1 2 þ C11 2b2 t
yA ¼
ðT1 T2 Þg C42 þ 2C1 C3 2C3 C11 2b2 t
yA ¼
ðT1 T2 Þg C2 C3 C1 C4 C12 2b2 t
yA ¼
ðT1 T2 Þg C1 C2 þ C3 C4 C2 bt C13
yA ¼
ðT1 T2 Þg 2C1 C3 C22 2 þ C11 2b2 t
yA ¼ 0
ðT T2 ÞgEI C1 C2 þ C3 C4 C2 MA ¼ 1 t C12 yA ¼
Simply supported
Guided RA ¼ 0
yA ¼
RA ¼ 0
ðT1 T2 Þg C4 C12 2b2 t
MA ¼ 0
yA ¼ 0
ðT T2 ÞgbEI 2C1 C3 þ C42 2C3 RA ¼ 1 t C13 yA ¼
ðT1 T2 Þg 2C12 þ C2 C4 2C1 2bt C13
RA ¼ 0
yA ¼ 0
MA ¼ 0
yA ¼
yA ¼ 0 RA ¼ 0
ðT1 T2 ÞgEI 2C12 þ C2 C4 2C1 t 2 þ C11
yA ¼ 0
ðT1 T2 Þg C1 C2 þ C3 C4 2bt 1 þ C11
yA ¼ 0
MA ¼
RA ¼ 0
yA ¼ 0
ðT1 T2 ÞgEI t
yA ¼ 0
ðT T2 ÞgEI C12 þ C32 C1 MA ¼ 1 t 1 þ C11 yA ¼
ðT T2 ÞgbEI C2 C3 C1 C4 RA ¼ 1 t 1 þ C11
ðT T2 Þg2bEI C4 RA ¼ 1 t 2 þ C11 MA ¼
yA ¼ 0
ðT T2 ÞgEI MA ¼ 1 t
ðT1 T2 Þg 2b2 t
MA ¼ 0
C3 1 þ C11
yA ¼ 0
ðT T2 ÞgbEI C1 C2 þ C3 C4 C2 RA ¼ 1 t C14 yA ¼
ðT1 T2 Þg C2 C3 C1 C4 þ C4 2bt C14
yA ¼ 0
yA ¼ 0
ðT T2 ÞgbEI 2C3 RA ¼ 1 t C13 MA ¼
ðT1 T2 ÞgEI C2 C3 C1 C4 þ C4 t C13
RA ¼ 0
yA ¼ 0
ðT T2 ÞgEI MA ¼ 1 t yA ¼ 0
MA ¼ 0
yA ¼ 0
ðT T2 ÞgbEI C22 2C1 C3 RA ¼ 1 t C13 yA ¼
ðT1 T2 Þg 2C32 C2 C4 2bt C13
yA ¼ 0
yA ¼ 0
RA ¼ 0 MA ¼
ðT1 T2 ÞgEI t
[CHAP. 8
yA ¼ 0 Fixed
MA ¼ 0
Formulas for Stress and Strain
Bending moment ¼ M ¼ MA F1 þ
220
7. Uniform temperature differential from top to bottom
TABLE 8.6 NOTATION: All
Shear, moment, slope, and deflection formulas for semi-infinite beams on elastic foundations notation is the same as that for Table 8.5. No length is defined since these beams are assumed to extend from the left end, for which restraints are defined, to a length beyond that portion
The following constants and functions, involving both beam constants and foundation constants, are hereby defined in order to permit condensing the tabulated formulas which follow
8.17]
ko ¼ foundation modulus (unit stress per unit deflection); bo ¼ beam width; and b ¼ ðbo ko =4EIÞ1=4 . (Note: See page 131 for a definition of hx ain :Þ F1 ¼ cosh bx cos bx
A1 ¼ 0:5eba cos ba
B1 ¼ 0:5ebb cos bb
F2 ¼ cosh bx sin bx þ sinh bx cos bx
A2 ¼ 0:5eba ðsin ba cos baÞ
B2 ¼ 0:5ebb ðsin bb cos bbÞ
F3 ¼ sinh bx sin bx
ba
A3 ¼ 0:5e
F4 ¼ cosh bx sin bx sinh bx cos bx
ba
A4 ¼ 0:5e
B3 ¼ 0:5ebb sin bb
sin ba
ðsin ba þ cos baÞ
Fa1 ¼ hx aÞ0 cosh bhx aicos bhx ai Fa2 ¼ cosh bhx aisin bhx ai þ sinh bhx aicos bhx ai Fa3 ¼ sinh bhx aisin bhx ai
SEC.
affected by the loading. Note that MA and RA are reactions, not applied loads.
B4 ¼ 0:5ebb ðsin bb þ cos bbÞ Fb1 ¼ hx bi0 cosh bhx bicos bhx bi Fb2 ¼ cosh bhx bisin bhx bi þ sinhhbx bicos bhx bi Fb3 ¼ sinh bhx bisin bhx bi Fb4 ¼ cosh bhx bisin b bi sinh bhx bicos bhx bi Fb5 ¼ hx bi0 Fb1
Fa4 ¼ cosh bhx aisin bhx ai sinh bhx aicos bhx ai
Fb6 ¼ 2bðx bÞhx bi0 Fb2
0
Fa5 ¼ hx ai Fa1 0
Fa6 ¼ 2bðx aÞhx ai Fa2
Transverse shear ¼ V ¼ RA F1 yA 2EIb3 F2 yA 2EIb2 F3 MA bF4 þ LTV
Slope ¼ y ¼ yA F1 þ
RA F yA 2EIb2 F3 yA EIbF4 þ LTM 2b 2
MA RA F yA bF4 þ LTy F þ 2EIb 2 2EIb2 3
yA MA RA F þ F þ F þ LTy 2b 2 2EIb2 3 4EIb3 4 Expressions for RA, MA , yA , and yA are found below for several combinations of loading and left end restraints. The loading terms LTV , LTM , LTy ; and LTy are given for each loading condition. Deflection ¼ y ¼ yA F1 þ
Left end restraint Loading, reference no. 1. Concentrated intermediate load (if ba > 3, see case 10)
Free RA ¼ 0 yA ¼
W EIb2
RA ¼ 0
A2
MA ¼ yA ¼
yA ¼ 0
W A2 b W 2EIb3
Simply supported MA ¼ 0
RA ¼ 2WA1 yA ¼
A4
yA ¼ 0
W EIb2
A3
Fixed yA ¼ 0
yA ¼ 0
RA ¼ 2WA4 2W MA ¼ A b 3
Loading terms LTV ¼ WFa1 LTM ¼ LTy ¼ LTy ¼
W F 2b a2 W 2EIb2 W 4EIb3
Fa3 Fa4
221
W A1 EIb3 (if a ¼ 0, see case 8) yA ¼
Guided
MA ¼ 0
Beams; Flexure of Straight Bars
Bending moment ¼ M ¼ MA F1 þ
Shear, moment, slope, and deflection formulas for semi-infinite beams on elastic foundations (Continued)
222
TABLE 8.6
Left end restraint reference no. 2. Uniformly distributed load from a to b
Free RA ¼ 0 yA ¼
MA ¼ 0
w ðB3 A3 Þ EIb3
w ðB2 A2 Þ yA ¼ 2EIb4
Guided RA ¼ 0 MA ¼
yA ¼ 0
w ðB3 A3 Þ b2
w ðB1 A1 Þ yA ¼ 2EIb4
Simply supported MA ¼ 0 RA ¼
yA ¼ 0
w ðB A2 Þ b 2
w ðB4 A4 Þ yA ¼ 2EIb3
Fixed yA ¼ 0 RA ¼
yA ¼ 0
2w ðB1 A1 Þ b
w MA ¼ 2 ðB4 A4 Þ b
Loading terms w ðF Fb2 Þ LTV ¼ 2b a2 LTM ¼ LTy ¼ LTy
3. Uniform increasing load from a to b
MA ¼ 0 MA ¼ 0 yA ¼ 0 yA ¼ 0 RA ¼ 0 w B4 A4 w B4 A4 w B3 A3 2bB3 2bB3 bB2 yA ¼ MA ¼ 3 RA ¼ 2 4 b a b a b a 2EIb 2b b w B3 A3 w B2 A2 w B1 A1 bB yA ¼ y y ¼ ¼ 2bB þ bB4 2 A 1 A 5 5 4 ba ba ba 4EIb 2EIb 2EIb
RA ¼ 0
yA ¼ 0
yA ¼ 0 w B2 A2 2bB1 RA ¼ 2 b a b w B1 A1 MA ¼ 3 þ bB4 ba b
LTV LTM LTy LTy
4. Concentrated intermediate moment (if ba > 3, see case 11)
RA ¼ 0
MA ¼ 0
2Mo yA ¼ A EIb 1 yA ¼
Mo A4 EIb2
RA ¼ 0
yA ¼ 0
MA ¼ 2Mo A1 yA ¼
Mo EIb2
A3
MA ¼ 0
yA ¼ 0
RA ¼ 2Mo bA4 yA ¼
Mo A EIb 2
yA ¼ 0
yA ¼ 0
RA ¼ 4Mo bA3 MA ¼ 2Mo A2
ðif a ¼ 0; see case 9Þ RA ¼ 0
MA ¼ 0
yA ¼ 2yo A4 2yo yA ¼ A3 b
RA ¼ 0
yA ¼ 0
MA ¼ 2yo EIbA4 y yA ¼ o A2 b
MA ¼ 0
yA ¼ 0
yA ¼ 0
yA ¼ 0
RA ¼ 4yo EIb2 A3
RA ¼ 4yo EIb2 A2
yA ¼ 2yo A1
MA ¼ 4yo EIbA1
ðFa3 Fb3 Þ
w 4EIb3
ðFa4 Fb4 Þ
w ¼ ðFa5 Fb5 Þ 4EIb4 w Fa3 Fb3 bFb2 ¼ 2 b a 2b w Fa4 Fb4 2bFb3 ¼ 3 b a 4b w Fa5 Fb5 ¼ bFb4 4 b a 4EIb w Fa6 Fb6 2bFb5 ¼ 5 b a 8EIb
LTV ¼ Mo bFa4 LTM ¼ Mo Fa1 LTy ¼
Mo F 2EIb a2
LTy ¼
Mo Fa3 2EIb2
LTV ¼ 2yo EIb2 Fa3 LTM ¼ yo EIbFa4 LTy ¼ yo Fa1 LTy ¼
yo F 2b a2
[CHAP. 8
5. Externally created concentrated angular displacement
w 2b2
Formulas for Stress and Strain
Loading,
TABLE 8.6
Shear, moment, slope, and deflection formulas for semi-infinite beams on elastic foundations (Continued) RA ¼ 0
MA ¼ 0
RA ¼ 0
yA ¼ 0 2
yA ¼ 4Do bA3 yA ¼ 2Do A2
yA ¼ 2Do A1
yA ¼ 0
yA ¼ 0
3
yA ¼ 0 3
RA ¼ 4Do EIb A2
RA ¼ 8Do EIb A1
yA ¼ 2Do bA4
MA ¼ 4Do EIb2 A4
LTV ¼ 2Do EIb3 Fa2 LTM ¼ 2Do EIb2 Fa3 LTy ¼ Do bFa4
8.17]
MA ¼ 4Do EIb A3
MA ¼ 0
SEC.
6. Externally created concentrated lateral displacement
LTy ¼ Do Fa1
7. Uniform temperature differential from top to bottom
RA ¼ 0
RA ¼ 0
MA ¼ 0
T T2 g yA ¼ 1 tb yA ¼
T1 T2 2tb2
yA ¼ 0
T T2 gEI MA ¼ 1 t yA ¼ 0
g
MA ¼ 0
yA ¼ 0
yA ¼ 0
T T2 gEIb RA ¼ 1 t
RA ¼ 0
T T2 g yA ¼ 1 2tb
MA ¼
yA ¼ 0
T1 T2 gEI t
LTV ¼
T1 T2 gEIbF4 t
LTM ¼
T1 T2 gEIð1 F1 Þ t
LTy ¼
T1 T2 gF2 2tb
LTy ¼
T1 T2 gF3 2tb2
Simple loads on semi-infinite and on infinite