МИНИСТЕРСТВО ОБРАЗОВАНИЯ РОССИЙСКОЙ ФЕДЕРАЦИИ ВОСТОЧНО-СИБИРСКИЙ ГОСУДАРСТВЕННЫЙ ТЕХНОЛОГИЧЕСКИЙ УНИВЕРСИТЕТ Кафедра: «П...
7 downloads
125 Views
92KB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
МИНИСТЕРСТВО ОБРАЗОВАНИЯ РОССИЙСКОЙ ФЕДЕРАЦИИ ВОСТОЧНО-СИБИРСКИЙ ГОСУДАРСТВЕННЫЙ ТЕХНОЛОГИЧЕСКИЙ УНИВЕРСИТЕТ Кафедра: «Промышленное и гражданское строительство»
Программа расчета по определению площади сечения напрягаемой арматуры изгибаемых элементов таврового сечения
Составили: Степанова Д.С. Смирнова Н.Б.
Улан-Удэ, 2001 г.
{-- Определение площади сечения напрягаемой арматуры --------} {----------для случая 1 таврового сечения ----------} Program Arm; User CRT; Var {вводимые величины} M : real; B : real; H0 : real; B1 : real; R1 : real; G : real; R2 : real; Q : real; M1 : real; N : real; Cls : byte; Rsh: real; L : real; Np : byte; {вводимые величины} Rb : real; W : real; A1 : real; M2 : real; Q3 : real; Q2 : real; Q1 : real; A : real; A2 : real; G1 : real; P : real; Gsp: real; d Gsp : real; Gsr : real; begin Write (введите параметр М, Н*мм:’); ReadLn (M); Write (введите параметр b, мм:’); ReadLn (B); Write (введите параметр h0, мм:’); ReadLn (H0); Write (введите параметр b’’f, мм:’); ReadLn (B1); Write (введите параметр b’’f, мм:’); ReadLn (H1); Write (введите параметр L, м:’); ReadLn (L); Write (введите число напрягаемых стержней, шт:’); ReadLn (Hp); Write (введите параметр Rb, MПa:’); ReadLn (R1); Write (введите параметр g b2:’); ReadLn (G); Write (введите параметр Rsh, MПa:’); ReadLn (Rsh);
Write (введите параметр Rs, МПа:’); ReadLn (R2); Write (введите параметр mu min:’); ReadLn (M1); Write (введите параметр nu:’); ReadLn (N); Writeln (‘введите класс арматуры:’); Writeln (‘1) A-I.. A-III, A-IIIв, Bp-I’); Writeln (‘2) A-IV.. A-VI, B-II, Bp-II, K-7, K-19’); ReadLn (Cls); R1 :=G*R1; if M>R1*B1*H1*(H0-0.5*H1) then begin Writeln (‘Условие равновесия не выполняется.’); Halt; end; Q:=0.75*Rsh; P:=30+360/L; If Q+P> Rsh then begin WritLn (‘Условие не выполняется.’); Hilt; end; dGsp :=0.5*P/Q*(1+1/Sqrt(Np)); Gsp:=1-dGsp; Q:=Gsp*Q; W:=0.85-0.008*R1; case Cls of 1: Q1:=R2-Q; 2: Q1 :=R2+400-Q; else Q1:=R2+400-Q; end; if G<=1 then Q2:=W/(1+Q1/500*(1-W/1.1)) else Q2:=W/(1+Q1/400*(1-W/1.1)) repeat A:=M/R1/B1/H0/H0; Q3:=1-sqrt (1-2*A); H0:=H0+50; Unitel Q3 <= Q2; H0:=H0-50 G1:=N-(N-1)*(2*Q3/Q2-1); if G1 >= N then G1 :=N; if H1/H0 <= 0.2 then A1:=M/G1/R2/(1-0.5*Q3)/h0 else A1:=Q3*B1*H1*R1/G1/R2; M2:=A1/B/H0; If M2 >= M1 then A2:=A1
else A2:=M1*B*H0; Writeln (‘Полученное значение площади сечения равно:’ A2/100:0:2,’ см ^2’); Readln; end.
Пример расчета определения сечения напрягаемой арматуры для случая 1 таврового сечения Случай 1-сжатия зона сечения элемента с одиночной арматурой находится выше ребре, то есть нулевая линия проходит в пределах полки (х<=hf’). Это бывает, когда внешний момент оказывается меньше внутреннего момента, воспринимаемого сжатой полкой таврового сечения и соответствующей ей растянутой арматурой, относительно центра тяжести растянутой арматуры M<=Mf=Rbbf’hf’ (h0-0.5hf’) При заданной площади сечения растянутой арматуры случай 1 при соблюдении неравенства: RsAs<=Rbbf’hf’ Расчет тевровых сечений по случаю 1 ничем не отличается от расчета прямоугольных сечений шириной bf’. При hf’/h<=0.2 площадь сечения арматуры As можно определить по приближенному уравнению, полученному в предложении, что нейтральная ось проходит по середине полки (х=0,5 hf’): M=RsAs (h0-0.5 hf’); As=M/[Rs(h0-0.5hf’)] При этом ошибка в запас прочности достигает не более 10%.
Характеристика прочности бетона и арматуры 1. Многопустотную предварительно напряженную плиту армируют стержневой арматурой класса A-YI с электротермическим натяжением на упоры форм. К трещиностойкости плиты предъявляют требования третьей категории. Изделие подвергают тепловой обработке при атмосферном давлении. 2. Бетон тяжелый класса В 20, соответствующий напрягаемой арматуре. Нормативная призменная прочность Rbh=Mпа, расчетная Rb=11.5 Mпа: Коэффициент условий работы УВ2=0,9: нормативное сопротивление при растяжении Rbth=Rbt, ser=1.4 Мпа, расчетное Rbt=0.9 Мпа: начальный модуль пругости бетона ЕВ=27000 Мпа.
Требуется:
1. Вычислить площадь сечения растянутой арматуры.
{------ Арматуры класса A-III ------} М = 77800000 Н*мм; b = 330 мм; h0 = 210 мм; B’f = 1760 мм; h’f = 40.5 мм; Rb =11.5 Мпа; gb2 = 0.9; Rsh =390 Мпа; Rs = 365 Мпа; mu min = 0.01; nu = 1. Результат: 10,70 см^2. {------ Арматуры класса A-VI ------} М = 77800000 Н*мм; b = 330 мм; h0 = 210 мм; B’f = 1760 мм; h’f = 40.5 мм; L = 6.5 мм; Rb =11.5 Мпа; gb2 = 0.9; Rsh =590 Мпа; Rs = 510 Мпа; mu min = 0.01; nu = 1.2. Результат: 6,93 см^2. {------ Арматуры класса A-V ------} М = 77800000 Н*мм; b = 330 мм; h0 = 210 мм; B’f = 1760 мм; h’f = 40.5 мм; L = 6.5 мм; Rb =11.5 Мпа; gb2 = 0.9; Rsh = 785 Мпа; Rs = 680 Мпа; mu min = 0.01; nu = 1.15. Результат: 6,93 см^2. {------ Арматуры класса A-VI ------}
М = 77800000 Н*мм; b = 330 мм; h0 = 210 мм; B’f = 1760 мм; h’f = 40.5 мм; L = 6.5 мм; Rb =11.5 Мпа; gb2 = 0.9; Rsh = 980 Мпа; Rs = 815 Мпа; mu min = 0.01; nu = 1.1. Результат: 6,93 см^2.
Редактор Т.А. Стороженко Подписано в печать 01.02.2001 г. Формат 60х84 1/16 Усп. п.л. 0,93, уч. – изд. л. 0,88. Тираж 30 экз. РИО ВСГТУ. Улан-Удэ, ул. Ключевская 40 а,