RF and Microwave Oscillator Design
For a listing of recent titles in the Artech House Microwave Library, turn to the b...
157 downloads
1499 Views
8MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
RF and Microwave Oscillator Design
For a listing of recent titles in the Artech House Microwave Library, turn to the back of this book.
RF and Microwave Oscillator Design
Michał Odyniec Editor
Artech House Boston • London www.artechhouse.com
Library of Congress Cataloging-in-Publication Data Odyniec, Michał. RF and microwave oscillator design / Michał Odyniec. p. cm. — (Artech House microwave library) Includes bibliographical references and index. ISBN 1-58053-320-5 (alk. paper) 1. Radio frequency oscillators. 2. Oscillators, Microwave. I. Title. II. Series. TK7872.O7 O34 2002 621.384’12—dc21 2002027960
British Library Cataloguing in Publication Data Odyniec, Michał. RF and microwave oscillator design. — (Artech House microwave library) 1. Radio frequency oscillators 2. Oscillators, Microwave—Design I. Title 621.3’8412 ISBN 1-58053-320-5
Cover design by Gary Ragaglia
2002 ARTECH HOUSE, INC. 685 Canton Street Norwood, MA 02062 All rights reserved. Printed and bound in the United States of America. No part of this book may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying, recording, or by any information storage and retrieval system, without permission in writing from the publisher. All terms mentioned in this book that are known to be trademarks or service marks have been appropriately capitalized. Artech House cannot attest to the accuracy of this information. Use of a term in this book should not be regarded as affecting the validity of any trademark or service mark. International Standard Book Number: 1-58053-320-5 Library of Congress Catalog Card Number: 2002027960 10 9 8 7 6 5 4 3 2 1
Contents
1
Preface
xi
Acknowledgments
xv
Developments of Microwave Oscillator Theory
1
1.1
Introduction
1
1.2
Van der Pol (1927)
2
1.3
J. R. Pierce (1943)
3
1.4
R. Adler (1946)
4
1.5
W. A. Edson and J. A. Mullen (1960)
7
1.6
C. T. Rucker (1969)
8
1.7
K. Kurokawa (1973) References
10 13
2
Methods of Oscillator Design
15
2.1
Introduction
15 v
vi
RF and Microwave Oscillator Design
2.2 2.2.1 2.2.2 2.2.3
Nonlinear Dynamics of a Simple Oscillator Oscillator Equation Phase-Plane Analysis Generalizations of Phase-Plane Analysis
16 16 19 22
2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5
Stability of the Operating Point Introduction Circuit Linearization Counterexample Validity Limits of the Intuitive Criterion Conclusions
23 23 24 25 28 29
2.4 2.4.1 2.4.2
29 29
2.4.4 2.4.5 2.4.6
High-Q Oscillators Steady-State Periodic Oscillations Large Signal Impedance and Corresponding Nonlinear Characteristics Notes on Feedback Representation, High Q, and Small Parameter Large Signal S-Parameters Nonresistive Active Circuit Conclusions
33 36 38 40
2.5 2.5.1 2.5.2
Dynamics of High-Q Oscillators Introduction Oscillation Stability
40 40 41
2.6
Oscillations in the Presence of an External Signal Introduction Circuit Equations Resonance Characteristics
43 43 43 45
Summary References
48 50
Appendix 2A: Nyquist Stability Criterion
52
Appendix 2B: Justification of the Describing Function Method
53
2.4.3
2.6.1 2.6.2 2.6.3 2.7
31
Contents
vii
Appendix 2C: Transformation VoltageCurrent to Amplitude-Phase Equations
56
Appendix 2D: Theorems on Averaging Acknowledgments
58 58
Linearity, Time Variation, and Oscillator Phase Noise
59
3.1
Introduction
59
3.2
General Considerations
61
3.3 3.3.1
Detailed Considerations: Phase Noise Phase Noise of an Ideal Oscillator
64 64
3.4 3.4.1
The Roles of Linearity and Time Variation in Phase Noise Close-In Phase Noise
68 78
3.5 3.5.1 3.5.2
Circuit Examples LC Oscillators Ring Oscillators
79 79 84
3.6
Amplitude Response
88
3.7
Summary References
90 90
Appendix 3A: Notes on Simulation Acknowledgments
92 92
4
High-Frequency Oscillator Circuit Design
93
4.1 4.1.1 4.1.2
Transistor CAD-Oriented Circuit Models Introduction Homojunction and Heterojunction Bipolar Transistor Modeling
95 95
3
96
viii
RF and Microwave Oscillator Design
4.1.3 4.1.4 4.1.5 4.1.6 4.1.7 4.1.8
4.2 4.2.1 4.2.2 4.2.3 4.2.4 4.3
FET Operating and Modeling Transistor I-V and S-Parameter Measurement System Model Extraction Procedure Noise Sources in Semiconductor Devices and Their CAD-Oriented Modeling Transistor Low-Frequency Noise Characterization Modeling of Circuit-CAD–Oriented Noise Sources in HBTs and FETs Oscillator Circuit Design Tools Conventional Linear Theory of Sinusoidal Oscillators Steady-State Analysis of Transistor Oscillators Nonlinear Stability of Free-Running Oscillators Oscillator Phase-Noise Characterization
102 115 118 130 134 150 156 156 167 169 172
4.3.6 4.3.7
Design Rules of Low Phase-Noise FreeRunning Oscillators Phase Noise in One-Port Oscillator Circuit Generalization to Transistor-Oscillator Circuits A Very Useful Design Tool: The Transistor Load-Line Finding the Maximum Added Power of the Transistor by Numerical Calculation Optimization and Localization of the Energy Stored in the Circuit AM/PM Conversion Conclusion
190 193 194
4.4 4.4.1 4.4.2
Practical Examples Breadboard Oscillators Oscillators on MMIC Technology
195 195 200
4.3.1 4.3.2 4.3.3 4.3.4 4.3.5
182 184 186 187 188
Contents
ix
4.4.3 4.4.4
MMIC FET-Based Oscillator Examples MMIC HBT-Based Oscillator Example
202 210
4.5
Conclusion References
212 214
Appendix 4A: HBT and HEMT Nonlinear Models
221
Appendix 4B: Transistor Low-Frequency Noise Characterization
226
Appendix 4C: Numerical Simulations of an Oscillator Benchmark Acknowledgments
235 238
Modern Harmonic-Balance Techniques for Oscillator Analysis and Optimization
245
5.1
Introduction
245
5.2
HB Analysis of Autonomous Quasi-Periodic Regimes in Nonlinear Circuits Autonomous Quasi-Periodic Regimes The Mixed-Mode Newton Iteration Degenerate Solutions and Their Suppression Applications
246 246 248 253 256
5
5.2.1 5.2.2 5.2.3 5.2.4 5.3 5.3.1 5.3.2 5.3.3 5.3.4 5.3.5 5.3.6
Synchronous and Asynchronous Stability Solution Paths in a Harmonic Phasor Space Natural Frequencies of Quasi-Periodic Steady States Nyquist’s Analysis for Time-Periodic Steady States Global Stability Analysis Applications Spurious Oscillations and Related Bifurcation Diagrams
260 261 267 270 274 284 294
x
RF and Microwave Oscillator Design
5.4 5.4.1 5.4.2 5.4.3 5.4.4 5.4.5 5.4.6 5.4.7 5.5 5.5.1 5.5.2 5.6 5.6.1 5.6.2 5.6.3 5.6.4 5.7 5.7.1 5.7.2
CAD-Oriented Oscillator Design Techniques General Optimization Methods Oscillator Optimization by Substitution Methods Design for Oscillation Buildup and SteadyState Stability Computation of the Gradient Applications A Case Study: CAD of a Broadband VCO Oscillator Design for Asynchronous Stability Electromagnetics-Based Optimization of Microwave Oscillators Direct-Newton Optimization Applications Iterative Methods for Large Self-Oscillating Nonlinear Circuit Analysis Inexact-Newton HB for Forced Circuits Computation of the Krylov Subspace Basis Vectors Extension to Large Autonomous Circuits Applications
301 303 312 315 319 320 325 337
343 344 349
351 352 356 360 363
Global Stability Analysis of Large Autonomous Circuits Fundamental Bifurcation Detection for Large Circuits Applications References
366 370 375
About the Authors
377
Index
383
366
Preface There is no need to justify interest in oscillators; they form the heart of all kinds of communication systems and more. Whenever we tune a radio, check the time, use a cellular phone, or even pick up a portable telephone receiver, we rely on a properly working oscillator. Oscillators are intrinsically nonlinear circuits that exhibit a wealth of nonlinear phenomena. Some of these phenomena are desirable from the designer’s point of view; some are not. The very utility of oscillators is based on the nonlinear effect of coexistence of unique and stable periodic oscillations and an unstable quiescent point. Other phenomena, such as the coexistence of several periodic solutions (manifested as spurious oscillations), hysteresis, bifurcation, and the existence of strange attractors, are to be avoided. Because of this wealth of complex behavior, oscillator design remains more an art than a science. At the beginning of oscillator development, theory closely followed practical design. Van der Pol’s theoretical works appeared a few years after the first triode oscillators were invented, and a few years later Krylov and Bogoliubov provided a rigorous justification of the van der Pol approach. The situation changed when triodes, which were well described by van der Pol cubic nonlinearity, were replaced by transistors, which were not. Only a very few of the best designers were able to apply van der Pol methods to microwave oscillators, as is described in Chapter 1. Some designers adapted methods from control theory, which led to successful designs described in Chapters 1 and 2. Still, their methods were little known in the broader design community. A common approach was to make the operating point unstable in the hope that unique and stable oscillations would appear. The xi
xii
RF and Microwave Oscillator Design
circuits and devices were too complicated to attempt much more with standard engineering tools. At the same time, the ideas of van der Pol, Krylov, and Bogoliubov bore fruit in the area of dynamical systems. They merged with the earlier works of Poincare and gave rise to methods of averaging and of integral manifolds. Cartwright and Littlewood’s analysis of the van der Pol equation inspired Smale’s work and his invention of the horseshoe structure. Unfortunately their theory was hardly accessible to engineers, and their examples were limited to triode oscillators and the original cubic van der Pol equation. The situation has changed with the arrival of CAD tools: first, SPICE, and then, harmonic balance and envelope simulators. They made complex circuits and devices tractable and at the same time showed the need for an understanding of nonlinear behavior. We believe that now nonlinear tools and methods have reached the stage at which they can be effectively applied to design. This book aims to make advanced design tools available to practicing engineers. It presents the state of the art in design in language accessible to the hands-on engineer. Since linear design (i.e., design for the unstable operating point) is well covered in the literature, this book focuses on nonlinear design and is structured to guide the reader to its most important aspects. The book consists of five chapters. The first three provide tutorials on oscillator design. The last two present advanced methods in real-life design, including device modeling and circuit-simulation methods. In Chapter 1, Kaneyuki Kurokawa describes the development of nonlinear design, including his pioneering work. He relates the evolution of design methods to development in instrumentation and measurements. Chapter 2 introduces methods of nonlinear analysis, using a simple IC structure as an example. It relates the classic van der Pol approach to the theory of dynamical systems and to the high-Q oscillators described by Kurokawa. Chapter 3 introduces, in detail, phase noise analysis. It uses time domain description to explain noise behavior carefully. Chapter 4 presents the full design of a modern oscillator and focuses on the reproducible performance of the low phase noise microwave transistor oscillator, including a high production volume MMIC VCO. This chapter starts with the nonlinear modeling of active devices; then it discusses linear and nonlinear simulation and noise analysis. The ideas presented in Chapters 1 and 2 are combined with modern simulation tools. Phase noise analysis includes spectral description, as well as the methods developed in Chapter 3. Chapter 5 discusses in detail the harmonic balance methods that proved to be so effective in oscillator analysis and design. It
Preface
xiii
also discusses nonlinear phenomena encountered even in simple oscillators, including the bifurcation of oscillations from a quiescent point and the bifurcation of almost periodic oscillations from existing periodic oscillations. The exposition is aimed at all levels of design expertise; it covers elementary oscillator behavior, as well as advanced methods and models. It is intended for use as both a reference for the practicing designer and as a textbook for senior-level students. We hope that new designers will find here a readable introduction to design, combined with an overview of various methods of differing levels of complexity. At the same time, an experienced designer will find here his favorite methods presented from different viewpoints.
Acknowledgments The inspiration for this book came from the Workshop on Oscillator Design held at International Microwave Symposium in Boston, Massachusetts, in June 2000, which received very favorable feedback. I have been very fortunate to obtain contributions to the workshop and to this book from internationally recognized experts. I would like to thank them all for outstanding contributions. I would also like to acknowledge Jacek Kudrewicz, Ganesh Basawapatna, and Jack Hale, on whose shoulders my personal oscillator knowledge rests. Michał Odyniec El Cerrito, California September 2002
xv
1 Developments of Microwave Oscillator Theory Kaneyuki Kurokawa 1.1 Introduction Oscillators convert direct current (dc) power to radio frequency (RF). They are one of the most fundamental components in RF and microwave systems. However, an oscillator is inherently nonlinear. If it were linear, the oscillation amplitude would grow indefinitely with time. No steady state would be reached. For linear systems, the principle of superposition holds. A complex phenomenon can be decomposed into simpler phenomena; each of these simpler phenomena can be studied independently, and their superposition explains the original complex phenomenon. This type of convenient and powerful method is not applicable for the study of an oscillator because of its nonlinearity. However, if the oscillator is divided into two parts, the linear passive circuit and the nonlinear active device, then the vast amount of knowledge accumulated for linear passive circuits can be advantageously used for the discussion of the linear passive part. In any branch of science, the actual situation is often too complicated to study. Accordingly, a simplified model is constructed, and the behavior of the model is studied. The model usually neglects various factors, which, one hopes, yield only minor effects. After the model is constructed and the equation is given describing the behavior of the model, the direct solution of the equation is sometimes found to be difficult, and approximations 1
2
RF and Microwave Oscillator Design
become necessary. The success of the model and approximations is determined by whether the analysis explains observed phenomena or not. As the techniques of measurement and observation improve, so does the theory, which explains observed phenomena. The history of microwave oscillator theory is the history of the appropriate model construction and approximations. This chapter reviews some of early papers on microwave oscillator theory to determine what kind of models and approximations were used as the observational techniques improved.
1.2 Van der Pol (1927) In his classical paper published in Philosophical Magazine in 1927, van der Pol discussed the phase-locking phenomena observed with beat receivers [1]. A beat receiver is a vacuum tube oscillator that produces audio beat output when a carrier is injected under a near-locking condition. It was used as a sensitive detector of weak signals in wireless telegraphy. A survey of textbooks on wireless communications published around 1920 will show that an enormous number of pages are devoted to the discussion of beat receivers. As late as 1947, the classical textbook [2] by Terman, Radio Engineering, spent one page on beat receivers under the name of oscillating detectors. As a model of the beat receiver, van der Pol presented the following nonlinear differential equation: V¨ + (−␣ + 3␥ V 2 )V˙ + 20 V = B 21 sin 1 t
(1.1)
where V stands for the anode voltage of the triode, and the right-hand side represents the injection signal, and −␣ is the negative resistance necessary for oscillation to start. The term 3␥ V 2 represents the nonlinear resistance, without which the oscillation amplitude will grow indefinitely with time. A concrete derivation of (1.1) is presented in [3]. Using (1.1), van der Pol clarified when the phase locking takes place. He also clarified how the RF amplitude varies with the injection signal amplitude and frequency. Although he did not present experimental data, it was obvious that his results agreed very well with observations. The phase locking could be detected by the sudden disappearance of the audio output, and the RF amplitude could be measured by a vacuum tube voltmeter. When solving this nonlinear differential equation, van der Pol used various approximations. Most importantly, he neglected completely the third harmonic, even though the third harmonic
Developments of Microwave Oscillator Theory
3
amplitude produced by the nonlinear term has the same order of magnitude as that of the fundamental component. The fact that, in spite of this omission, his analysis showed an excellent qualitative agreement with observations profoundly influenced the later development of oscillator theory. The excellent agreement is due to the circuit being detuned at the third harmonic frequency.
1.3 J. R. Pierce (1943) During World War II, researchers at Bell Laboratories and the MIT Radiation Laboratory studied various oscillator circuits for radar applications, including the reflex klystron and magnetron. Summarizing these wide-ranging studies, J. R. Pierce of Bell Laboratories presented a general theory of oscillator behaviors in an internal technical memorandum [4], known as ‘‘mm.’’ This was in 1943. His ‘‘mm’’ was immediately classified as confidential. He neglected harmonics from the beginning. Consequently, in the steady state, the circuit admittance Y plus the electronic admittance Y E must be equal to zero: YE + Y = 0
(1.2)
Note that Y E represents the nonlinear device and that Y represents the linear passive circuit mentioned in the introduction. Pierce assumed that Y E is a function of voltage V alone and that Y is a function of angular frequency alone. To investigate the stability of each solution satisfying (1.2), he introduced a complex frequency:
= r + j i
(1.3)
e j t = e j ( r + j i )t = e j r t e − i t
(1.4)
Since
positive i means that the amplitude is decreasing with time and negative i means that the amplitude is increasing with time. When V deviates from a steady-state value by dV, the corresponding d is obtained from (1.2) as follows: dY dY E dV + d = 0 dV d
(1.5)
4
RF and Microwave Oscillator Design
hence
冤 冥
dY E dV dV = kdV d = − dY d
(1.6)
If Im (k ) > 0, then the oscillation is stable. This is because when V increases slightly from the steady-state value, dV is positive and d i becomes positive, which means that the amplitude decreases with time, returning toward the original steady-state value. Similarly, when V decreases, the amplitude increases with time and returns to the original steady-state value. If Im (k ) < 0, a slight deviation of V from the steady-state value causes a further deviation. As a result, the oscillation is unstable. By the time Pierce wrote his memorandum, the circuit admittance at microwave frequencies could be accurately measured using a slotted section and the Smith chart. Therefore, the possibility of multiple intersections between the circuit admittance locus and the device line (the negative of the electronic admittance locus) was clearly recognized, and since each intersection satisfies (1.2) and corresponds to a possible oscillation, determining which intersection gives a stable operation was an important subject of study. When the memorandum was declassified 10 years later, W. A. Edson of General Electric (GE) presented the stability criterion in his book, Vacuum Tube Oscillators [5]. J. C. Slater also presented a graphical form of the same criterion in his book, Microwave Electronics [6]. However, Slater did not present the mathematical formula itself, probably because Pierce’s memorandum was yet to be released at the time of his publication. Today, many textbooks on microwaves present Pierce’s stability criterion. However, the appearance is different, since k is first decomposed into the real and imaginary parts and the condition is given in a form in which the expression of the imaginary part is larger than zero. Furthermore, nobody seems to refer to Pierce’s memorandum anymore.
1.4 R. Adler (1946) Independent of these wartime efforts, R. Adler of the Zenith Corporation observed the experimental study of vacuum tube audio oscillators at 1,000 Hz conducted by his colleagues and obtained a differential equation for the oscillator phase to satisfy [7]. It is given by
Developments of Microwave Oscillator Theory
E d␣ = − 1 0 sin ␣ + ⌬ 0 dt E 2Q
5
(1.7)
where E 1 is the voltage of the impressed signal at 1 , E is the voltage induced in the grid circuit, Q is the quality factor of the plate load, and ␣ is the phase relative to the impressed signal. ⌬ 0 is the difference between the free-running angular frequency 0 and 1 . In the steady state, the lefthand side is zero and sin ␣ is not larger than 1, so the locking condition is given by
| |
⌬ 0 E1 > 2Q E 0
(1.8)
Rewriting this condition, we obtain Adler’s formula for locking range: ⌬ max =
0 E1 2Q E
(1.9)
This simple and easy-to-understand formula was referred to in many papers. Adler’s formula was, however, misinterpreted in some microwave papers by a factor of 2 as ⌬ max =
0 2Q
√
P1 P0
In this formula, P 0 is the oscillator output power and P 1 is the injection signal power. The locking range is usually ‘‘verified’’ by locking experiments. The fact that the locking range is proportional to the square root of the injection signal power does not prove the proportionality constant being correct. Norman Kenyon of Bell Laboratories measured circuit parameters of a transistor oscillator at 350 kHz and confirmed that this formula is indeed incorrect by a factor of 2 [8]. The correct formula is given by ⌬ max =
0 Q ext
√
P1 1 P 0 cos
(1.10)
There are three different Q s in microwaves: the unloaded Q , the loaded Q , and the external Q . Among them, the external Q is the Q to be used in the locking formula. Neglecting the term 1/cos , (1.10) gives Adler’s
6
RF and Microwave Oscillator Design
formula, since P 0 is E 2 divided by the load resistance R , and P 1 is the injection signal power, which is the available power of the injection signal source, E 12 divided by 4R . is a new variable. It is the slope angle of the device line shown in Figure 1.1. The more slanting the device line, the wider the locking range. One could use the impedance locus Z ( ) as well. Then, the device line is minus the electronic impedance, Z ( A ). In addition to the popular locking range formula, Adler solved (1.7) without using approximations and obtained the closed form solutions
␣ 1 tan = − 2 K ␣ 1 tan = + 2 K
√1 − K
2
K
√K
2
K
−1
⌬ 0 (t − t 0 ) tanh 2 ⌬ 0 (t − t 0 ) tan 2
√1 − K
√K
K 2
K
−1
2
(K < 1)
(1.11)
(K > 1)
where K = 2Q
⌬ 0 E 0 E1
(1.12)
These solutions (1.11) show how the oscillator phase changes with time during locking transient (K < 1) as well as under near-locking conditions (K > 1). Note that audio waveforms could be directly observed on the
Figure 1.1 The circuit admittance locus and the device line (minus the electronic admittance) with the angle .
Developments of Microwave Oscillator Theory
7
oscilloscope screen, and one could correlate the phase change with observations. Slater presented the same analysis in his book Microwave Electronics even though waveforms could not be observed at microwave frequencies. Long after Slater’s book was published, the spectrum analyzer became standard laboratory equipment and the triangular shape of the spectra envelope under near-locking conditions attracted researchers’ attention. Then, M. Armand of CSF, France, among others, gave an excellent account [9] for the envelope in 1969 by calculating the spectrum intensities using Adler’s solution under near-locking conditions. In terms of sin =
1 , ⍀ = ⌬ 0 cos K
(1.13)
the result is given by Frequency
Complex Amplitude
1
j tan
1 + ⍀ 1 + n ⍀
冉 冉
E 2
冊 冊冉
j e E 2 1 − tan2 j tan 2 2 1 − tan2
冊
n−1
e jn E
Except for the first term, the spectrum intensities form a geometric sequence. As a result, on the spectrum analyzer screen with a decibel scale, they become an arithmetic sequence, explaining the triangular shape of the spectra envelope very well. Suddenly, Adler’s solution as a function of time became relevant to microwaves, confirming Slater’s foresight.
1.5 W. A. Edson and J. A. Mullen (1960) W. A. Edson of GE and J. A. Mullen of Raytheon each published a noise paper in the same issue of the Proceedings of the IRE in 1960. Edson’s paper used a conceptual approach [10], while Mullen’s paper was mathematical [11]. Each treated a second-order differential equation, which means that a single resonant circuit is assumed. Both papers studied amplitude modulation (AM) and frequency modulation (FM) noise and presented the output spectrum of oscillators. Note that, by then, the spectrum of oscillator output
8
RF and Microwave Oscillator Design
became directly observable on the spectrum analyzer screen. Consequently, they could discuss oscillator noise in terms of observable quantities.
1.6 C. T. Rucker (1969) To increase the output power of radar, multiple tube oscillators were extensively studied during World War II. Push-pull circuits were thoroughly practical, but the circuits combining more than two tubes became increasingly difficult because of parasitic oscillations, or the so-called mode problem, and no solution of the mode problem was found. In the early days of microwave solid-state oscillator development, a number of power combiners were again proposed. In most of these proposals, individual oscillators were first built and then their output power was combined by means of hybrid circuits or transmission lines. Although the proposed circuits were always reported as stable, the stable operations were rarely reproducible in other laboratories. These circuits were in a near degenerate state and hence inherently unstable. Small changes in the load condition, or in the supply voltage, or even in the ambient temperature bring about sudden changes in the mode of operation. The output power as well as the oscillation frequency literally jumps from one value to another giving an unacceptable performance. This is the same mode problem as suffered by radar pioneers during World War II. This mode problem was solved by the ingenious proposal of a symmetrical oscillator [12] by C. T. Rucker of the Georgia Institute of Technology in 1969. In his oscillator, the power-combing circuit constitutes an integral part of the oscillator circuit. The devices are located physically far apart from each other, yet the behavior of the oscillator becomes identical to that of an oscillator with devices connected in parallel. It consists of five coaxial transmission lines, each about /4 long, terminated by a device, and arranged radially about a common bias network and a common output network as schematically illustrated in Figure 1.2. A resistor R s is incorporated in each coaxial center conductor to eliminate instabilities commonly observed with multiple oscillator arrangements. The capacitance C between the output coupling disk and each coaxial center conductor provides the necessary coupling to the common load R L . The bypass capacitor in the bias network is located about /4 away from the hub of the oscillator. Since the relation between one device port and the neighboring device port is identical to the relation between one device port and any other device port, and since the circuit is reciprocal, the impedance matrix [13] of the oscillator circuit looking in from the device ports is given by
Developments of Microwave Oscillator Theory
9
Figure 1.2 Rucker’s symmetrical oscillator.
Z( ) =
冤
Z 11 Z 12 Z 12 Z 12 Z 12
Z 12 Z 11 Z 12 Z 12 Z 12
Z 12 Z 12 Z 11 Z 12 Z 12
Z 12 Z 12 Z 12 Z 11 Z 12
Z 12 Z 12 Z 12 Z 12 Z 11
冥
(1.14)
The corresponding negative device impedance matrix is given by Z(A) = diag [ Z (A 1 ), Z (A 2 ), Z (A 3 ), Z (A 4 ), Z (A 5 )]
(1.15)
where diag [ ] indicates a diagonal matrix. The oscillation condition is given by Z( )i = Z(A)i
(1.16)
Equation (1.16) can be systematically solved using the eigenvectors of Z( ) and the corresponding eigenvalues. They are respectively given by
10
RF and Microwave Oscillator Design
xn =
1 √5
冤 冥 1 exp ( jna ) exp ( j 2na ) exp ( j 3na ) exp ( j 4na )
(1.17)
and
n = Z 11 + Z 12 (e jna + e j 2na + e j 3na + e j 4na )
(1.18)
where n runs from 0 to 4 and a = 2 /5. Since
0 = Z 11 + 4Z 12
(1.19)
1 = 2 = 3 = 4 = Z 11 − Z 12
(1.20)
one can easily choose the circuit parameters in such a way that 0 can be equal to Z (A ) but 1 cannot be equal to Z (A ) in the whole range of A and . Then, the oscillation will take place in the 0th mode, and all the other modes from n = 1 to 4 are completely suppressed. This is the reason why Rucker’s symmetrical oscillator is free from the mode problem. Once the principle is known, the physical symmetry is not necessary. As long as the circuit is electrically symmetric, the same principle applies. As a result, many practical multiple device oscillators have been successfully proposed. The above solution of the oscillator mode problem may be considered as a triumph of the oscillator circuit theory. However, multiple-device oscillators are no longer being used in practice. This is because, today, transistor power amplifiers are easier to build and maintain.
1.7 K. Kurokawa (1973) My own work on oscillator theory was prompted by the separate measurements of AM and FM noise of phase-locked oscillators conducted by J. Josenhans at Bell Laboratories in 1966 [14]. I presented a graphical interpretation of the phase-locking phenomena extending Slater’s discussion in his book, Microwave Electronics. The phase-locking condition [15] is given by [ Z ( 1 ) − Z (A )]I = E
(1.21)
Developments of Microwave Oscillator Theory
11
where E represents the injection signal voltage at 1 ; A is the current amplitude; Z ( 1 ) is the circuit impedance; and −Z (A ) is the device impedance. For small signal injection, the RF current amplitude A will stay approximately the same as the free-running amplitude A 0 . So, (1.21) gives Z ( 1 ) = Z (A ) +
|E | A0
e −j
(1.22)
where is the phase difference between I and E . The formula (1.22) indicates that the distance from Z (A ) to Z ( 1 ) is equal to | E | /A 0 under the locking condition. There are, in general, two points on the device line that satisfy this condition as shown by the tails of the solid and dotted arrows in Figure 1.3. However, only one of them, that of the solid arrow, corresponds to a stable locking. I clarified graphically the stability condition of injection locking. Using the graphical discussion, the locking range formula (1.10) was obtained. Furthermore, the AM and FM noise of oscillators under various conditions could be qualitatively discussed. For the analytical study of oscillators, I used the relation
= 1 +
1 dA d −j dt A dt
(1.23)
instead of the complex frequency given by (1.3). This is because I was interested in the fluctuations of amplitude A and phase .
Figure 1.3 The circuit impedance locus and the device line with the injection vector (solid arrow).
12
RF and Microwave Oscillator Design
In the ac circuit theory, the time derivative is everywhere replaced by multiplication by j . This is justifiable since dn dt n
Re [Ae j ( t + ) ] = Re [( j )n Ae j ( t + ) ]
(1.24)
if A and are constant. When A and are slowly varying functions of time, to the first-order approximation for n > 1 and exactly for n = 1, the n th time derivative becomes dn dt
n Re [Ae
j ( 1 t + )
] = Re
再冋 冉
d j 1 + dt
冊
1 dA + A dt
册
n
冎
Ae j ( 1 t + )
(1.25) This means that Re [Z ( ) Ae j ( 1 t + ) ] will give approximately the voltage across the impedance Z ( ) when is replaced by 1 + (d /dt ) − j (1/A )(dA /dt ) everywhere in Z ( ). Using (1.23) turned out to be a convenient method of analyzing various oscillator behaviors. Thanks to the orthogonal relation between sine and cosine functions, real-time differential equations of A and can be obtained. Utilizing these differential equations, topics such as the effects of nonlinear reactance, the variation of circulator output, phase-modulated injection signals, AM and FM noise, noisy injection signals, the effects of nonlinear reactance on noise, and large signal injection could be all discussed in a coherent manner as presented in [15]. The active element in my 1973 paper was a negative resistance device such as a tunnel diode, a Gunn diode, or IMPATT. In the meantime, the preferred active element became a transistor. Note that, interchanging the role of impedance with that of admittance as in the Pierce memorandum, the discussion dual to my paper is directly applicable to regenerative transistor oscillators, since the transistor acts as a negative conductance device in a regenerative oscillator. Similarly, the same discussion is also applicable to Hartley and Colpitts transistor oscillators since the transistor acts again as a negative conductance in the generalized odd mode when the even mode is detuned as is usually the case. Furthermore, imbedding a transistor in a reactive network, a one-port negative conductance device can be created to use as an active device for an oscillator design. The imbedding reactive network must be as simple as possible so that the frequency characteristics of the one-port device can be neglected compared to the frequency characteris-
Developments of Microwave Oscillator Theory
13
tics of the circuit admittance. Because of the simplicity of the negative conductance model, it becomes straightforward to analyze nonlinear effects, such as the power variation of a phase-locked oscillator and the maximum power oscillation. Now, looking back at all these developments in the past, it seems that what could be observed or measured has profoundly affected what shape the oscillator theory took in the next evolution. Furthermore, history teaches us that the ingenious solution of a difficult problem may turn out to be of little use because of subsequent progress.
References [1]
van der Pol, B., ‘‘Forced Oscillations in a Circuit with Nonlinear Resistance (Reception with Reactive Triode),’’ Phil. Mag., S. 7., Vol. 3, No. 13, January 1927, pp. 65–80.
[2]
Terman, F. E., Radio Engineering, New York: McGraw-Hill, 1947, p. 540.
[3]
van der Pol, B., ‘‘The Nonlinear Theory of Electric Oscillations,’’ Proc. of the Institute of Radio Engineers, Vol. 22, No. 9, September 1934, pp. 1051–1086.
[4]
Pierce, J. R., ‘‘Oscillator Behavior,’’ Memorandum for File, mm-43-140-19, Bell Laboratories, June 19, 1943.
[5]
Edson, W. A., Vacuum Tube Oscillators, New York: John Wiley and Sons, 1953.
[6]
Slater, J. C., Microwave Electronics, New York: Van Nostrand, 1950.
[7]
Adler, R., ‘‘A Study of Locking Phenomena in Oscillators,’’ Proc. IRE, Vol. 34, June 1946, pp. 351–357.
[8]
Kenyon, N. D., ‘‘A Lumped-Circuit Study of Basic Oscillator Behavior,’’ Bell Systems Technical Journal, Vol. 49, February 1970, pp. 255–272.
[9]
Armand, M., ‘‘On the Output Spectrum of Unlocked Driven Oscillators,’’ Proc. IEEE (Lett.), Vol. 57, May 1969, pp. 798–799.
[10]
Edson, W. A., ‘‘Noise in Oscillators,’’ Proc. IRE, Vol. 48, August 1960, pp. 1454–1466.
[11]
Mullen, J. A., ‘‘Background Noise in Nonlinear Oscillators,’’ Proc. IRE, Vol. 48, August 1960, pp. 1467–1473.
[12]
Rucker, C. T., ‘‘A Multiple-Diode High-Average-Power Avalanche-Diode Oscillator,’’ IEEE Trans. on Microwave Theory and Techniques (Corresp.), Vol. MTT-17, December 1969, pp. 1156–1158.
[13]
Kurokawa, K., ‘‘An Analysis of Rucker’s Multi-Device Symmetrical Oscillators,’’ IEEE Trans. on Microwave Theory and Techniques (Corresp.), Vol. MTT-18, November 1970, pp. 967–969.
[14]
Josenhans, J., ‘‘Noise Spectra of Read Diode and Gunn Oscillators,’’ Proc. IEEE (Lett.), Vol. 54, October 1966, pp. 1478–1479.
[15]
Kurokawa, K., ‘‘Injection Locking of Microwave Solid-State Oscillators,’’ Proc. IEEE, Vol. 61, October 1973, pp. 1386–1410.
2 Methods of Oscillator Design Michał Odyniec
2.1 Introduction Since its very beginnings until the 1970s, oscillator design has evolved on three parallel courses. The most common approach focuses on creating conditions under which oscillations can start. It deals with small-signal circuits (i.e., circuits that are linearized about the operating point) and with the selection of structures and components that make the operating point unstable. The second approach, described in Chapter 1, applies van der Pol ideas to microwave oscillator development. It is very effective but little known. The third approach uses van der Pol ideas to characterize nonlinear oscillations. It is even less known in engineering circles than the second. The reason is that the original, cubic nonlinearity of the van der Pol equation has lost relevance to transistor circuits. However, van der Pol ideas gave rise to the theory of nonlinear oscillations and dynamical systems. Among the concepts that can be directly traced to van der Pol equations are averaging, integral manifolds, and Smale’s horseshoe [1–6]. The development of CAD tools in the 1970s transformed design practice [7]. On one hand, it gave designers insight into nonlinear circuits; on the other, it showed the danger of blind applications of the tools. The development of harmonic balance simulators in the 1980s proved particularly useful for oscillator design. 15
16
RF and Microwave Oscillator Design
This chapter shows interrelations between those approaches. We use a simple, commonly used oscillator to illustrate their power and their limits and the ways in which they utilize and enhance the CAD tools. Section 2.2 describes our oscillator with the use of the generalized van der Pol equations and discusses its full dynamics. Section 2.3 presents a rigorous analysis of stability criteria. Sections 2.4–2.7 generalize van der Pol results to high-Q (but otherwise arbitrary) oscillators, discuss the extension of harmonic balance techniques, and combine the high-Q assumption with dynamical analysis.
2.2 Nonlinear Dynamics of a Simple Oscillator 2.2.1 Oscillator Equation This section analyzes one of the simplest and widely used oscillator structures; it is shown in Figure 2.1. The cross-coupled transistors form a nonlinear, locally active circuit while the LC circuit models the resonator. The circuit is simple, yet generic enough to exhibit common oscillator behaviors; its various modifications appear in Chapter 3 and in [8–10]. Here we use the circuit as a modern illustration of the generalized van der Pol theory, which was the starting point of oscillator theory. Let v (t ) denote the voltage across the capacitor and i L (t ) the current through the inductance L . If we neglect the high-frequency transistor parasistics and the reactances of the biasing circuit, the oscillator can be described by a generalized van der Pol equation: L
di L =v dt
C
(2.1)
dv = −i L − i n (v ) dt
The function i n (v ) = i a (v ) + G res v represents the current-voltage characteristics of the oscillator seen from the resonator’s terminals A-B as shown in Figure 2.2. We have included the resonator conductance G res into the nonlinear characteristics for the sake of convenience; it will have no effect on the results. The exact shape of these characteristics is determined by the crosscoupled transistors and the biasing circuit. The bias parameters of V CC = 5V, R1 = R2 = 500 ohm, I dc = 10 mV, and G res = 0.001 mho result in the shape shown in Figure 2.3.
Methods of Oscillator Design
17
Figure 2.1 Simple oscillator.
Let us note that the nonlinear resistance (including the resonator resistance G res ) is ‘‘N-shaped’’ (i.e., its slope, which represents the small-signal conductance, is negative for small voltages and positive for large ones). Thus, the nonlinear circuit is active (i.e., it delivers energy to the resonator for small signals). For large signals it becomes lossy. A cubic polynomial used by van der Pol is the simplest N-shaped nonlinearity. We shall show that practically all of van der Pol results are valid for an N-shaped nonlinear characteristic and therefore applicable for modern oscillator structures.1 The original van der Pol equation is easily obtained from (2.1) by taking a time derivative of its second part and substituting the v /L for di L /dt . That yields 1. Rigorously speaking, we call a function f (v ) ‘‘N-shaped’’ if f (0) = 0, if f (v ) is monotonically decreasing about zero and is monotonically growing for | v | larger than certain constant, and if it is convex for v > 0 and concave for v < 0. Those last conditions mean that its second derivative (if it exists) is positive for v > 0 and negative for v < 0.
18
RF and Microwave Oscillator Design
Figure 2.2 Practical realization of an active circuit (nonlinear resistance).
v¨ +
di n v˙ /C + v /LC = 0 dv
(2.2)
This is a standard form of an oscillator equation with the natural frequency 20 = 1/LC and the admittance (dissipative force in mechanical di oscillator) n . For (2.2) the N-shape requirement of i n (v ) translates into dv di n (v ) i a (v ) = + G res being negative about zero (thus, G res must be small dv dv enough so that the resonator losses do not quench the oscillations) and monotonically increasing with v. The condition is of course satisfied by van der Pol’s cubic nonlinearity i n (v ) = G (−v + v 3/3) derivative, which results di (v ) = G (−1 + v 2 ) characteristics. in the n dv
Methods of Oscillator Design
19
Figure 2.3 The I-V characteristics that includes G res , seen by the ideal resonator.
2.2.2 Phase-Plane Analysis We apply now the phase plane methods [2, 11–13] to (2.1). We introduce the plane (hence the name of the method) of the possible values of the voltage v and the current i L . In that plane we trace v and i L parameterized by time to obtain the transient and steady-state behaviors. This trajectory tracing can be done numerically as shown in Figure 2.4(a). Superimposed on the trajectories is the reversed characteristic of the nonlinear resistance i L (v ) = −i n (v ). We have put this reversed characteristic in, because it shows the points at which the right side of the second part of (2.1) equals zero. Figure 2.4(b) represents a pair of voltages across the resonator and a pair of currents through the inductance. In each pair one waveform originates at low value of the current and the other one at a high value of the current. In Figure 2.4(a) the same waveforms are represented on the voltage-current plane as trajectories parameterized by time; one of them spirals out, and the other spirals down to the same steady-state solution (which mathematicians
20
RF and Microwave Oscillator Design
Figure 2.4 Dynamics of an LC oscillator o C = 0.1 mho: (a) phase-plane and (b) waveforms.
call a limit cycle). The steady-state solution is not shown on the plane, but its position can be easily discerned from the behavior of the two trajectories. The power of the phase-plane analysis, however, lies in the fact that we can predict the circuit behavior even without any numerical calculations. Indeed, let us note that the tangent vector to each trajectory equals (dv /dt , di /dt ). Whenever a trajectory crosses the vertical axis v = 0, then di /dt = 0 [because of the first part of (2.1)], and the trajectory is horizontal. Moreover, for v > 0, we have di /dt > 0 and the trajectory goes upward; for v < 0, it goes downward. A similar argument can be applied to the voltage v (t ). On the reversed nonlinear resistor characteristics i L (v ) = −i n (v ), we get dv /dt = 0; thus, every trajectory crosses the characteristic vertically. We already know that it will point upward for v > 0 and downward for v < 0. Moreover, we have dv /dt < 0 above the characteristics and dv /dt > 0 below it. Combining that with the information on the sign of di /dt (positive for positive v and negative for negative v ), we get a complete picture of the behavior of trajectories. Any trajectory passes the positive vertical half axis horizontally directed to the left; then it keeps turning down until it hits the reversed resistive characteristics where it points down directly. Subsequently,
Methods of Oscillator Design
21
it continues turning right until it hits the negative half of the vertical axis where it points horizontally to the right, and then it keeps turning upward to the reversed resistive characteristics where it points up; then it keeps turning left until it hits the positive half of the vertical axis, and so on. The trajectories starting near the origin spiral outward while those originating ‘‘far’’ spiral inward. As another example of a qualitative argument we consider the circuit from Figure 2.1 with small resonator capacitance C . In that case the time derivative of the voltage v˙ = −(i L + i n (v ))/C is large everywhere except in the immediate vicinity of the reversed nonlinear characteristics i L = −i n (v ). Consequently the trajectories either follow the shape of the characteristics or move very fast horizontally as shown in Figure 2.5(a). Thus the corresponding voltage waveforms have parts of slow motion connected by quick jumps as shown in Figure 2.5(b).
Figure 2.5 Relaxation oscillations in the very low-Q resonator o C = 0.001 mho: (a) phaseplane and (b) waveforms.
22
RF and Microwave Oscillator Design
The above analysis illustrates the way in which the general behavior of the system can be determined even without numerical simulations. Even more can be done [2, 12]: For example, the existence, the number, and the stability of the periodic trajectories can be approximated from the shape of the nonlinear resistance. One does it by constructing an annulus with large external boundary and the internal boundary just about the bias point. If the annulus boundaries meet only entering trajectories, then at least one periodic solution exists [12]. Since for large values of voltage and current the system is dissipative, all trajectories that cross the outer boundary are directed inside the annulus. If the bias point is unstable, then all trajectories that cross the internal boundary are also directed inside the annulus. Consequently, the circuit oscillates. This construction forms the basis of popular oscillator design: ‘‘If we assure that the operating point is unstable, then the circuit oscillates.’’ For an N-shaped symmetric characteristic, we can prove that the oscillations are unique and stable [12, 13]. Moreover, we know [2] that for a second-order equation the only steady-state waveform is either periodic or constant and that for an N-shaped characteristic the system will have an unstable operating point and a stable periodic solution. Also for either large or small values of Q , the shape of the periodic solution and that of the transients can be discerned from the shape of the i n (v ) characteristics. 2.2.3 Generalizations of Phase-Plane Analysis We have analyzed the oscillator model in which the resonator is represented by an LC circuit and the active part by a nonlinear resistance. Within those two assumptions, the results are powerful, intuitive, and rigorous. In particular, we know that the only possible steady states are either constant or periodic and that the orientation of the trajectories is easily estimated from the signs of the right-hand sides of the circuit differential equations. Moreover, for the N-shaped characteristics the oscillations are unique and stable. Since all that we need is the N-shape, our results apply directly not only to cross-coupled transistors but also to IMPATT, Gunn, and tunnel diodes. The theory also allows us to predict the shapes of the voltage and current waveforms and thus the power flow in the oscillator. A thorough analysis of the physical interpretation of second-order classical equations (of van der Pol and Duffing) can be found in [11, 14, 15]. Thanks to the ease of use and the clear physical interpretation of the results, there is a natural tendency to expand the phase plane results to more complex circuits. In the case of high-Q oscillators the generalization can be
Methods of Oscillator Design
23
justified both intuitively and rigorously. Intuitively a high-Q resonator near a resonance can be well modeled by an LC circuit. Moreover, such a resonator varies quickly with frequency so that we can neglect the frequency dependence of the active part and treat it as a nonlinear resistance. The rigorous argument is based on the integral manifolds theory [1–3, 16]. Consequently, the circuit in Figure 2.1 can be treated as a generic oscillator that is simple but includes the main features of any high-Q oscillator circuit. Because of that, we will continue to use it to introduce other methods of nonlinear analysis. The relaxation oscillation behavior that we analyzed for small capacitance was one of the first cases of strange ‘‘chaotic’’ behavior observed and the one that resulted in rigorous analysis of the phenomenon. As long as the system is represented on the plane without an external excitation, the most complicated behavior is periodic. However, if we add a periodic source in parallel with the resonator, then things change. In that case we can imagine the nonlinear characteristics in Figure 2.5(a) as periodically moving up and down. This movement, superimposed with the quick horizontal movement of trajectories caused by the small C, makes the areas near the characteristics extrema stretch and fold onto themselves creating Smale’s horseshoes. A rigorous analysis of a piecewise-linear N-shape has been done by Mark Levi [4]. Another analysis of the classic van der Pol equation from the dynamical system point of view was done by John Guckenheimer [17]. It can serve as a good introduction to the dynamical systems’ language.
2.3 Stability of the Operating Point 2.3.1 Introduction The fundamental question of oscillator design—Will it oscillate?—is usually reduced to: Is the operating point stable?2 The overwhelming majority of oscillator design literature analyzes circuit structures and components values that make the operating point unstable [9, 18–24].3 2. These two problems are not equivalent. In Chapter 5 we will see examples of stable oscillations coexisting with a stable operating point. This situation usually results in hysteresis behavior of the oscillator. 3. Among those, this author’s favorite works are [9] for design philosophy and [20, 23] for practical designs.
24
RF and Microwave Oscillator Design
Because linear design is widely covered in the literature, we shall not repeat its principles here. Instead we shall discuss just one of its aspects, which is widely and usually incorrectly used. To rigorously determine the operating point stability, we linearize the oscillator equations about it. If the eigenvalues of the linearized equations lie in the right half plane, then the point is unstable. In practice, designers prefer to linearize the circuit rather than the equations, which is done by using small-signal (i.e., linearized) models of nonlinear circuit components. The position of the eigenvalues (called characteristic frequencies ) is seldom checked directly. Instead the Nyquist criterion (see Appendix 2A) or some of its simplified forms are used. One of the most widely used criteria [21, 22, 24–35] states that ‘‘when the phase of the transfer function is zero and the magnitude (at the same frequency) is larger than one, then the system is unstable.’’ For microwave circuits the criterion is usually presented in terms of S-parameters and formulated as follows: If the conditions (2.3) hold, arg(S n ) = −arg(S r ),
| Sn Sr | > 1
(2.3)
then the double-reflected signal adds in phase and is bigger than the original one. Consequently, the signal grows and the circuit oscillates. Moreover, after the signal has grown, the gain diminishes so that the conditions (2.3) turn into arg(S n ) = −arg(S r ),
| Sn Sr | = 1
(2.4)
from which the amplitude and frequency of the signal can be determined. This section shows that the criterion (2.3) is not necessarily true and should be replaced by the analysis of the Nyquist plot. The criterion (2.4) is valid and will be discussed in Section 2.4. Although similar in appearance to (2.3), it describes a different physical phenomenon—the steady-state, large-signal oscillation—and is reached at in a very different manner. 2.3.2 Circuit Linearization When interested in ‘‘small’’ signals, we expand the nonlinear characteristics into a Taylor series about the operating point V dc : i n (V dc + v ) = i n (V dc ) + i n′ (V dc ) v + i n″(V dc ) v 2/2 + . . .
(2.5)
Methods of Oscillator Design
25
More precisely, we analyze the voltage and current of the form V dc + v , I dc + i , where I dc = i n (V dc ) and v and i are ‘‘small.’’ Substituting (2.5) back into (2.1), and neglecting all the higher-order terms, we get circuit equations, which are linear (in v, i L ): L
di L =v dt
C
(2.6)
dv = −i L − i a′ (V dc ) v − G res v dt
Note that the ‘‘small signal’’ circuit shown in Figure 2.6(b) is described by (2.6) with g a = −i a′ (V dc ). The circuit losses are determined by the resistors: If G res − g a = i n′ (V dc ) < 0, then the circuit is unstable. This fact can be checked analytically by applying the Laplace transform to (2.6), which yields: sLi L (s ) − Li L 0 = v (s )
(2.7a)
sCv (s ) − Cv 0 = −i L (s ) − i a′ (V dc ) v (s ) − G res v (s ) where v 0 and i L 0 are the initial values of voltage and current. Solving (2.7a) for v (s ), we get v (s ) =
sv 0 2
s + 2⑀ s + 20
(2.7b)
1 , ⑀ = (G res + i a′ (V dc ))/2C LC The poles of (2.7b) s 1,2 = −⑀ ± √ 20 − ⑀ 2 are often called characteristic frequencies of (2.7a); they are equal to eigenvalues of (2.6). Applying the inverse Laplace transform to (2.7b), we obtain voltage waveforms that are sinusoidal (as long as ⑀ < 0 ) with frequency ⑀ = √ 20 − ⑀ 2 and an exponentially varying amplitude v 0 e −⑀ t. We confirm that if G res + i a′ (V dc ) < 0, then ⑀ < 0, the amplitude grows, and the operating point is unstable.
where 20 =
2.3.3 Counterexample When G res + i a′ (V dc ) < 0, our circuit is unstable. Let us represent it via S-parameters and apply to it the Nyquist criterion together with the criterion
26
RF and Microwave Oscillator Design
Figure 2.6 Linearization of the simple oscillator: (a) an ‘‘osctest’’ probe from a commercially available simulator separates the resonator from the active circuit and (b) a linearized RLC circuit.
(2.3). We are using the S-parameters for two reasons: (1) S-parameters are commonly used in microwave design and are included in many commercially available software simulation tools and (2) their behavior is counterintuitive. Consequently, the simplified stability criterion (2.3) may easily produce confusing results. The Nyquist plots shown in Figure 2.7 have been calculated for S-parameters with three values of the characteristic impedance Z 0k = 1/Y 0k ,
Methods of Oscillator Design
27
Figure 2.7 Nyquist plots for the simple oscillator for varying Y 0 = 1/Z 0 : (a) G res < g a < Y 01 , (b) G res < Y 02 < g a , and (c) Y 03 < G res < g a .
28
RF and Microwave Oscillator Design
k = 1, 2, 3 such that G res < g a < Y 01 [see Figure 2.7(a)], G res < Y 02 < g a [see Figure 2.7(b)], and Y 03 < G res < g a [see Figure 2.7(c)], where g a = −i a′ (V dc ). Since our circuit is unstable the Nyquist loop, shown in the lefthand plots in Figure 2.7, encircles the point 1 + j 0 for every value of Z 0k , k = 1, 2, 3. However, if we turn to the magnitude-phase plots (shown to the right), then the circuit instability is hard to deduce. Finally the intuitive condition (2.3) obviously fails for G res < Y 02 < g a [Figure 2.7(b)] because we cannot find zero-crossing, and for Y 03 < G res < g a [Figure 2.7(c)] because at the zero-crossing | S n S r | < 1. The S n S r contours in Figure 2.7 clearly show that it is the encirclement of 1 + j 0 that matters (as we know from Nyquist theorem) and not the value of S n S r at the crossing of the real axis. 2.3.4 Validity Limits of the Intuitive Criterion As we have seen above, the intuitive criterion (2.3) may fail. The reason is that it assumes that the Nyquist contour is ‘‘simple,’’ by which we mean that its characteristic is similar to that of a selective filter and has the following properties: • It turns clockwise with . • It begins and ends at the origin (a bandpass filter has this property). • It crosses the real axis only once for positive (the negative- -part
of the contour is the mirror image of the positive one). If, as described in Chapter 4, it crosses the real axis more than once, then it should return to the origin (or a ‘‘safe area’’ far to the left from 1 + j 0) between the ‘‘resonance’’ crossings. For a ‘‘simple’’ contour in the above-defined sense, it suffices to find the crossing of real axis [i.e., find the point for which arg(S n ) = −arg(S r )]. If at this point | S n S r | > 1, then, because of the three ‘‘simplicity’’ conditions, the Nyquist loop encircles the point 1 + j 0, and the circuit is unstable. Let us revisit the circuit in Figure 2.6(b). It has S r ( ) =
2 − 2 + j (G res − Y 0 )/C Y 0 − Y res ( ) = − 02 Y 0 + Y res ( ) 0 − 2 + j (G res + Y 0 )/C
(2.8)
For ‘‘large’’ and ‘‘small’’ frequencies, the contour S r ( ) is close to −1 + j *0. Therefore, the contour S n S r ( 0 ) always begins and starts at −S n and crosses the real axis at
Methods of Oscillator Design
S n S r ( 0 ) =
Y 0 + ga Y 0 − G res Y 0 − ga Y 0 + G res
29
(2.9)
Y 0 + ga Y − G res and S r ( 0 ) = 0 vary in the Y 0 − ga Y 0 + G res three cases we get the plots as shown in Figure 2.7. Thus, even in a very simple circuit, such as the one above, an unfortunate choice of Y 0 = 1/Z 0 causes the Nyquist contours to behave nonintuitively and makes the simplified criterion (2.3) useless. Let us note that the admittance/ impedance description is more intuitive than the S-parameter one. That led some authors to the conclusion that the admittance/impedance description is the correct one as opposed to S-parameters [32]. As we have seen above, both descriptions are valid when used with the Nyquist stability criterion. The only advantage of the impedance-admittance representation is that for high-Q resonators it more often produces a ‘‘simple’’ loop. If the resonator has high Q, then it varies in frequency much faster than the active part of the circuit. Consequently, S n can be considered independent of frequency, and the criterion can be rephrased in a form particularly convenient for applications: The system is unstable if the contour S r ( j ) encircles 1/S n . Consequently, it is easy to change parameters of the active circuit so that the encirclement happens. The method of stability circles [36] follows immediately from this formulation. Since the signs of S n =
2.3.5 Conclusions We have used a very simple unstable circuit to show that the widely used intuitive criterion (2.3) may fail and should be replaced by the Nyquist stability criterion. The theory presented here is not new [18, 37, 38], but unfortunately it has often been incorrectly applied. We hope that the example will help to clarify the use of stability criteria.
2.4 High-Q Oscillators 2.4.1 Steady-State Periodic Oscillations This section analyzes the periodic steady state in high-Q4 oscillators. For the sake of simplicity we shall follow our oscillator; however, the methods 4. The rigorous definition of ‘‘high’’ Q is as follows: We require that the nonlinear characteristics of the circuit are bounded and satisfy the Lipschitz condition (i.e., their slopes are bounded). Then, for the theorems of this section and the following sections to hold,
30
RF and Microwave Oscillator Design
presented here are applicable to high-Q but otherwise arbitrary resonators. Also, the nonlinear part of the circuit does not have to be purely resistive. Cavity, DRO, SAW, XTO, or YIG oscillators fall into that category. When interested in the steady-state periodic oscillations, we represent the waveforms by their Fourier series: K
v (t ) =
∑
k = −K
v k e jk t, i (t ) =
K
∑
k = −K
i k e jk t
(2.10)
In principle, the series in (2.10) are infinite; in practice, however, we argue that no physical circuit supports infinitely high frequencies, and we truncate the series at a finite number K . How to choose the value of K is an important design decision. The answer is usually based on the filtering properties of the circuit and often supported by trial and error. Substituting (2.10) into (2.1) we obtain a system of algebraic equations: jk Li k = v k
k = 0, 1, 2, . . . , K
(2.11)
jk Cv k = −i k − i nk (v 0 , v 1 , . . . , v K ) where T
1 i nk (v 0 , v 1 , v 2 , . . . , v K ) = 2T
冕 冢∑ K
in
−T
k = −K
冣
v k e jk t e −jk t dt
We consider only the nonnegative indices k = 1, 2, . . . , K because, for the real valued waveforms, the harmonics with the indices of opposite signs are complex conjugate. We have thus reduced a system of differential equations to a (larger) system of algebraic equations from which harmonic coefficients of the oscillations can be found. There are two approaches to solving (2.11). One, called the harmonic balance method, provides solution algorithms for a finite, although possibly large, K . Because of its power and relative simplicity, the there exists a number Q 0 , which depends on the characteristics and their slope boundaries, such that for any Q > Q 0 , the theorems are satisfied. We call the Q that satisfies Q > Q 0 the high Q.
Methods of Oscillator Design
31
harmonic balance became a standard part of circuit simulators. It is discussed in detail in Chapter 5.5 The second approach, which we will discuss here, applies to the resonators with high Q. In that approach we neglect all the harmonics except the first, thereby reducing the system to a single algebraic equation in complex variables. This was the assumption made by van der Pol and by the methods described in Chapter 1. 2.4.2 Large Signal Impedance and Corresponding Nonlinear Characteristics For a high-Q resonator all harmonics except the first are negligible and (2.11) reduces to6 j Li 1 = v 1
(2.12)
j Cv 1 = −i 1 − i n1 (0, v 1 , 0, . . . ) where T
1 i n1 (0, v 1 , 0, 0) = 2T
=
1
冕
i n (v 1 e j t + v −1 e −j t ) e −j t dt
−T
冕
i n (2 | v 1 | cos ) cos d
0
For an oscillator with a high-Q but otherwise arbitrary resonator, the first harmonic equation will have the form: Y r ( ) v 1 = i n1 (0, v 1 , 0, . . . )
(2.13)
5. As long as the number of equations K is finite, the algorithm is easily generalized to any finite set of frequencies k that do not need to be harmonically related; therefore, the method also covers quasi-periodic oscillations [39]. 6. It turns out that the assumption can be justified for a general class of oscillators [40, 41]. Since the work is little known and important, not only for justification purposes but also for error estimates, we shall outline its line of reasoning in Appendix 2B.
32
RF and Microwave Oscillator Design
It is easy to see that for
20 − 2 , 20 = 1/LC Y r ( ) = jC (2.13) describes our oscillator. Since we deal with an autonomous system, we can choose an arbitrary time count. We choose it so that the v 1 becomes real and positive (the phase of v 1 becomes zero). To remember that the voltage fundamental is a real number, we introduce a new notation for the voltage amplitude A and for the amplitude of the current fundamental I (A ): A = 2 | v 1 | = 2v 1 2 I (A ) = i n1 (0, v 1 , 0, 0) =
(2.14)
冕
i n (A cos ) cos d
0
It follows from (2.14) that I (A ) is also real, which was to be expected since we had resistive linearity. Consequently, the oscillator’s voltage and current are close to sinusoidal waveforms v (t ) = A cos t
(2.15)
i (t ) = I (A ) cos t where the frequency and amplitude A are to be found from Y r ( ) A = I (A )
(2.16)
Let us note that with Pierce’s notation Y E = I (A )/A (2.16) is equivalent to (1.2). Similarly, in Kurokawa’s notation Y (A ) = I (A )/A , it is equivalent to (1.21) without the injection voltage and with impedances replaced by admittances (Kurokawa [42, 43] analyzed a series resonator while ours is parallel). The function Y (A ) = I (A )/A (or Y E ) can be interpreted as a large signal conductance (admittance in general). The concept of nonlinear characteristics defined by fundamental components of input and output signals has also been used in nonlinear control theory, with Y (A ) = I (A )/A , called a describing function.
Methods of Oscillator Design
33
Equation (2.16) is easy to solve. An ideal resonator’s admittance Y r ( ) is purely imaginary while Y (A ) = I (A )/A is real. Thus, we can separate variables and find the resonant frequency and the amplitude from Y r ( ) = 0
(2.17)
I (A ) = 0 If the resonator admittance is not purely imaginary, we still can separate the variables into Re(Y r ( ))A = I (A ) and Im(Y r ( )) = 0 and find the resonance frequency from the second equation and then the amplitude from the first. The variable separation property holds as long as the nonlinear element is resistive. In our circuit the oscillation frequency is found from the first equation to be √1/LC . Equation (2.17) has a simple physical interpretation: The oscillation frequency is determined by the resonant circuit, while the power of oscillation is determined by the active part of the circuit and resonator losses. In our parallel RLC oscillator the steady-state oscillations occur when the combined conductance of resonator’s losses and that of the active circuit is zero and I (A ) = 0. The value of the amplitude for which that happens can be found geometrically as shown in Figure 2.8. Our circuit is highly selective; thus, the power at the fundamental frequency P (A ) = AI (A )/2 well approximates the total power delivered to a high-Q circuit. Consequently, the sign of I (A ) determines whether the circuit is dissipative or oscillatory. Indeed the power is delivered to the circuit when I (A ) < 0 and is dissipated when I (A ) > 0. Consequently, (2.17) determines the amplitude A of a steady-state oscillation and its stability. Steady-state amplitude corresponds to the equilibrium of received and dissipated energy. It is stable because for A < A 0 we have I (A ) < 0; thus, the power is delivered to the system P (A ) = AI (A ) < 0 and the amplitude grows. For A > A 0 we have I (A ) > 0, the power is dissipated P (A ) = AI (A ) > 0, and the amplitude decreases. 2.4.3 Notes on Feedback Representation, High Q, and Small Parameter 2.4.3.1 Feedback Description
Following control theory we will call the method presented above the describing function method. It is particularly well-suited to an input-output description of a system. In fact, when rewritten as
34
RF and Microwave Oscillator Design
Figure 2.8 Nonlinear resistance and the corresponding fundamental I (A ). From I (A ) = 0 we determine the oscillation amplitude.
A = Z r ( ) I (A ) (2.16) suggests an input-output representation where the linear characteristic Z r ( ) = 1/Y r ( ) is interpreted as a ‘‘filter’’ block and I (A ) as a nonlinear block connected in a feedback loop. It is a pretty obvious but seldom-mentioned fact that a dynamical system, in our case (2.1), can have many equivalent feedback representations (2.16) [5]. To illustrate the idea, we introduce an arbitrary parameter 0 ≤ ␣ ≤ 1. For convenience and to be in tune with control theory, we also introduce dimensionless nonlinear characteristics—i n (v ), i a (v ), f (v )—such that i n (v ) = G res i n (v ) = G res (i a (v ) + (1 − ␣ ) v + ␣ v ) = G res ( f (v ) + ␣ v ) In Section 2.4, we chose ␣ = 0, which results in f (v ) = i n (v ).
Methods of Oscillator Design
35
Under the new notation (2.1) reads as L C
di L =v dt dv = −i L − ␣ G res v − G res f (v ) dt
Repeating the fundamental harmonics derivation from Section 2.4.2, we get: A = Z r ( ) F (A )
(2.18)
with the dimensionless transfer functions: Z r ( ) = −j LG res /(− 2LC + j L + 1) = −j G res /C ( 20 − 2 + j␣ G res /C ), F (A ) = I a (A ) + (1 − ␣ ) A Thus, for each 0 ≤ ␣ ≤ 1, (2.18) is a feedback representation of 2.1. Of course, the reasoning and the results of Section 2.4.2 remain valid for any 0 ≤ ␣ ≤ 1, as long as the ‘‘filter’’ Z r ( ) remains selective. 2.4.3.2 Small Parameter and High Q
For the describing function method to be valid, the ‘‘filter’’ Z r ( ) must be selective (must have high Q). However, the parameter ␣ G res /C is not necessarily small. Only after we normalize frequency to 0 , we get a smallparameter system: Z r ( ) = =
−j ( / 0 ) G res /(C 0 ) 1 − ( / 0 )2 + j ( / 0 ) ␣ G res /(C 0 ) −j ( / 0 ) G res /(C 0 ) 1 − ( / 0 )2 + j ( / 0 ) ␣ /Q
Similarly in (2.2) the parameter 1/C is not necessarily small; if, however, we introduce the dimensionless nonlinear characteristic i n (v ) = i n (v )/G res and a dimensionless time = 0 t that is scaled so that the natural frequency equals one, then
36
RF and Microwave Oscillator Design
dv 1 dv d 2v 1 d 2v , = = . d 0 dt d 2 20 dt 2 Consequently, (2.2) reduces to
20
d 2v d
2
+ G res
di n dv 0 /C + 20 v = 0 dv d
and further to d 2v d
2
+ (1/Q )
di n dv +v=0 dv d
Thus, a high-Q circuit corresponds to a ‘‘close-to-linear’’ system from the oscillation theory [11, 14, 15, 44] where ⑀ = 1/Q plays the role of the small parameter.7 From now on we will use the small parameter ⑀ together with our original notation t , i n (v ). The reader who prefers the dimensionless notation should treat t as dimensionless time, i n (v ) as the voltage-to-voltage function, and ⑀ as dimensionless ⑀ = 1/Q . The one who prefers physical parameters should treat t , i n (v ) as the original time and current and ⑀ as ⑀ = 1/C (and keep in mind that ⑀ becomes small in dimensionless units). Figure 2.9 compares the value of the oscillations amplitude obtained from (2.16) with phase portraits obtained for the same nonlinear characteristics for two values of Q . The oscillations amplitude obtained from I (A ) = 0 equals to A 0 = 0.8. Phase plane portraits show that for ⑀ = 0.03 the oscillations indeed stabilize at A 0 = 0.8. However, for a lower Q (⑀ = 0.15), they stabilize at about A 0 = 0.84, confirming the fact that the higher the Q is (the smaller ⑀ ), the better the describing function approximation. 2.4.4 Large Signal S-Parameters The above procedure can be easily extended to an S-parameter representation of the circuit. Indeed, for sinusoidal voltage and current (2.15) we define the ‘‘large-signal’’ incident and reflected waves: a = A + Z 0 I (A )/(2√Z 0 ), b = A − Z 0 I (A )/(2√Z 0 )
(2.19)
7. The parameter ⑀ introduced here and used until the end of this chapter is different that the one defined by (2.7b) in Section 2.3.2.
Methods of Oscillator Design
37
Figure 2.9 Comparison of the amplitude obtained via the describing function method with phase-plane portraits: (a) I = I (A ), (b) phase-plane for Q = 33 (⑀ = 0.03), and (c) phase-plane for Q = 6.6 (⑀ = 0.15).
where A and I (A ) are voltage and current fundamentals and we repeat the procedure. On the resonator side we have a = S r ( )b and on the active circuit side b = b (a ). These two relationships provide us with the steady-state equation a = S r ( ) b (a )
(2.20)
After defining the ‘‘large signal’’ S-parameter (which we easily recognize as an equivalent of the describing function Y (A ) = I (A )/A from the previous section): S n (a ) = b (a )/a, (2.20) is reduced to
38
RF and Microwave Oscillator Design
1 = S r ( ) S n (a )
(2.21)
which is equivalent to (2.16). Geometrical interpretation is shown in Figure 2.10. It is as simple as the one presented for large signal admittance. The crossing point of S r ( ) = 1/S n (a ) determines the frequency and amplitude of the oscillations. In our circuit the resonator characteristic coincides with the unit circle and the nonlinear resistance with the real axis; their crossing determines the frequency for which Im(S r ( )) = 0 and the amplitude of oscillations S n (a ) = 1. Note that (2.21) is exactly (2.4) from Section 2.3 on stability criteria. This equation determines the frequency and the amplitude of oscillations. We see now that when variables are separated then the S r is the same as the one obtained from the Nyquist loop. Consequently, in a high-Q circuit with real valued S n , the frequency at which the loop crosses the real axis is the oscillation frequency (more exactly, as shown in Appendix 2B, the two frequencies are close as long as we have a high-Q resonator). 2.4.5 Nonresistive Active Circuit The real-life active circuits cannot be treated as purely resistive except at very low frequencies. That is, the frequency and amplitude cannot be separated and the describing function equations should be represented as:
Figure 2.10 LS S-parameters.
Methods of Oscillator Design
S r ( ) S n (A , ) = 1
39
(2.22)
However, high-Q resonators are an exception to that rule. Indeed, in their case the variation of S n (A , ) with frequency is negligible relative to that of the high-Q resonator. As an illustration consider Figure 2.11 in which S r ( ) and 1/S n (A , ) are shown for our circuit with the transistors’ parasitic reactances included. Instead of a single trace S n (A ), we have many: S n (A , ), 1 < < 2 . However, the resonant part of the circuit varies so quickly with frequency that within the band of interest all the active traces are practically indistinguishable. Consequently, we can treat A and as separated variables, one determined by S n (A , ) ≈ S n (A ), and the other by S r ( ). Indeed, Figure 2.11 shows the resonator characteristics S r ( ) for a narrow frequency band (from 440 to 500 MHz), it coincides with the arc on the unit circle (because we have included the resonator losses into nonlinear circuit). We also plot
Figure 2.11 LS S-parameters for a real-life nonlinear circuit. The resonator characteristics S r ( ) coincide with the arc on the unit circle. The thick line shows 1/S n (A , ) varying with A for a fixed frequency value. It is crossed by very short thin lines that show 1/S n (A , ) at fixed amplitudes and varying frequency.
40
RF and Microwave Oscillator Design
1/S n (A , ). The thick line shows 1/S n (A , ) varying with A for a fixed frequency value. It is crossed by very short thin lines that show 1/S n (A , ) at fixed amplitudes and varying frequency. The frequency variation is negligible even though S n (A , ) varies over a much wider frequency band (from 400 to 600 MHz). Consequently, we treat all traces of 1/S n (A , ) within this band as one. Their crossing with S r ( ), which determines the amplitude and frequency, is shown by the marker m 2. 2.4.6 Conclusions We have shown that the oscillations in high-Q oscillators are nearly sinusoidal and that their frequency, amplitude, and power can be determined by a simple graphical construction. The construction has a straightforward physical interpretation; it consists of plotting an active circuit characteristic as depending on the amplitude and the resonator characteristic depending on frequency. Chapter 1 showed how the idea was developed and applied to nonlinear oscillator design. The method is rigorous (i.e., if the graphical method yields amplitude and frequency, we know that the exact solution exists and can estimate the error that we have made.) We have followed Kudrewicz [40] for its justification. A parallel work was done in the 1960s and the early 1970s in control theory. A good overview of this method, called a describing function method, can be found in Mees [5]. Availability of harmonic balance analysis in CAD tools made the describing function particularly easy to implement; at the same time, thanks to its physical insight, it forms a perfect tool to complement the harmonic balance analysis. The describing function concept has recently been applied to BiCMOS oscillator design by Wu and Hajimiri [10].
2.5 Dynamics of High-Q Oscillators 2.5.1 Introduction Let us now consider high-Q oscillators, in which the amplitude and phase vary slowly in time. The slow variation is forced by the high-Q property of the resonator. Chapter 1 shows how the concept arose in works of Adler, Edson, and Kurokawa. Its rigorous justification is based on the method of averaging developed by Krylov, Bogoliubov, and Mitropolskii for the systems with a small parameter [1–3]. Here we use our simple oscillator to show the principles lying behind the method and refer to Appendices 2C and 2D for its justification.
Methods of Oscillator Design
41
2.5.2 Oscillation Stability If the circuit has high Q, then the waveforms are close to sinusoidal, and it is convenient to perform the transformation of variables from voltagecurrent v, i L to amplitude-phase A , : v (t ) = A cos ( 0 t + ) i L (t ) = −
(2.23)
A 0 sin ( 0 t + ) L
where 0 = √1/LC is the natural frequency of the circuit. The amplitude of oscillations is described by the following ‘‘averaged’’ equation [1–3]8: A˙ = −⑀ I (A )
(2.24)
where 2 I (A ) =
冕
i n (A cos ) cos d
0
Mathematical proof of this fact is based on theory of averaging [1–3] (also see Appendix 2C). Intuitively one can argue that the sinusoidal waveform dominates all the others and therefore controls oscillator’s dynamics. Note that I (A ) is the same function that was defined by (2.14) and can easily be computed via a harmonic balanced simulator. Consequently, the constant solutions obtained by the method of averaging are equal to those obtained by the describing function method. The shape of I (A ) determines the oscillation’s buildup, from a small signal to the steady state (which corresponds to the constant amplitude) as shown in Figure 2.12. The insight into the amplitude’s behavior allows us to determine the stability of the constant solution. Indeed, the value of A 0 at which I (A 0 ) = 0 determines the (constant) amplitude of steady-state oscillations. If dI (A 0 )/dA < 0, then the oscillations are stable, because the oscillations with amplitudes smaller than A 0 grow and the ones with A > A 0 decrease. 8. The parameter ⑀ is ‘‘small’’ in a high-Q circuit. As explained in Section 2.4.3 ⑀ = 1/Q in dimensionless variables and ⑀ = 1/C in the original variables.
42
RF and Microwave Oscillator Design
Figure 2.12 Oscillation buildup from a small signal to A 0 such that I (A 0 ) = 0.
We reached the same conclusion from power considerations in Section 2.3 above; however, (2.24) additionally gives us the shape and the rate of the amplitude buildup. Moreover, knowing I (A ), we can calculate the time it takes for the oscillations to build up from an amplitude A 1 = A (t 1 ) to A 2 = A (t 2 ) [45]. Indeed, dividing both sides of (2.24) by ⑀I (A ) and integrating in time, we get t2
t2 − t1 =
1 ⑀
冕 t1
A2
Adt 1 = I (A ) ⑀
冕
dA I (A )
(2.25)
A1
Equation (2.25) has an important design application for minimizing battery usage in portable transceivers. Note that for small A we can linearize I (A ) = I ′(0)A and calculate the start time explicitly:
Methods of Oscillator Design A2
t2 − t1 =
1 ⑀
冕
43
冉 冊
1 dA A2 = ln I ′(0)A ⑀ I ′(0) A1
A1
Hence: A (t 2 ) = A (t 1 ) e ⑀ I ′(0)(t 2 − t 1 )
(2.26)
The exponential growth of small A (t ) is clearly visible in Figure 2.12. A general numerical algorithm called the envelope method, which can solve the problem and analyze modulated signals, has been invented independently by Edouard Ngoya and Remy Larcheveque at University of Limoges and by David Sharrit at Hewlett-Packard (now Agilent) and introduced into some commercially available software tools [46, 47]. Here we have shown that for high-Q oscillators a single harmonic can do the job.
2.6 Oscillations in the Presence of an External Signal 2.6.1 Introduction This section extends the results of Sections 2.4 and 2.5 to the oscillations in presence of an external signal. Specifically we show how the large signal characteristic I (A ) can be used to determine the existence and stability of synchronized oscillations. For the sake of clarity we shall use I (A ) simulated for our oscillator. As previously the analysis remains valid for any high-Q circuit with N-shaped nonlinear characteristics. 2.6.2 Circuit Equations Let an external signal s (t ) = B cos ( t ) be applied to the oscillator and modeled as a current source in parallel with the resonator. L C
di =v dt dv = −i − i n (v ) − B cos t dt
(2.27)
44
RF and Microwave Oscillator Design
Repeating the transformation of coordinates from Section 2.5 and Appendix 2C, we end up with averaged equations for amplitude and phase: 1 A˙ = − (I (A ) + B cos ) C
˙ = −␦ +
B sin CA
If we had used the dimensionless variables, then 1/C would have been replaced by 1/Q . Let us keep going with our universal small parameter ⑀ from Section 2.4.3 A˙ = −⑀ (I (A ) + B cos )
˙ = −␦ + ⑀
(2.28)
B sin A
where I (A ) is defined by (2.14), B denotes the amplitude of the locking signal, and ␦ = ( 2 − 20 )/2 ≈ − 0 denotes ‘‘the amount of detuning,’’ in the dimensionless variables ␦ = ( 2 − 20 )/2 0 ≈ ( − 0 )/ 0 .9 The constant solutions of the equations (2.28) can be found from I (A ) = −B cos
(2.29)
␦ A = ⑀ B sin which are equivalent to the fundamental harmonic equation I (A )/A − jC
2 − 20 = −Be j /A
(2.30)
Equation (2.30) is a special case of the Kurokawa equation (1.22) from Chapter 1: Y (A ) − Y r ( ) = Be j /A
(2.31)
9. The difference between our present case (locked oscillations) and the case in Section 2.5 (free oscillations) is that now the frequency is that of the injected signal, and the phase can be uniquely determined with reference to the injected signal; for the free-running oscillations, the phase was undetermined, and we considered only amplitude equations.
Methods of Oscillator Design
45
Let us discuss (2.28) and (2.29) in some detail because they provide a simple graphical method of finding locked oscillations and determining the locking range. Note first that (2.29) possesses the constant solution only if ␦ ≤ ⑀ B /A holds. This condition is a rigorous representation of the fact that the frequency locks only when the synchronizing frequency is close to the natural frequency of the circuit (i.e., the ‘‘amount of detuning’’ is small). Moreover, the locking zone increases with increasing external signal (B ) and decreasing Q (increasing ⑀ ). Section 2.6.3 looks more closely at the behavior of these solutions. 2.6.3 Resonance Characteristics We have seen that the constant solutions of (2.28), and consequently the amplitude and phase of locked oscillations, are determined by (2.29). Let us discuss now the behavior of the solutions of (2.29). They turn out to have a simple geometrical interpretation. Indeed, adding up the squared sides of (2.29) we conclude that the amplitude of locked oscillations satisfies the scalar equation: I (A )2 + A 2(␦ /⑀ )2 = B 2
(2.32)
Equation (2.32) describes the relationship between A , B, and ␦ /⑀ . For fixed B it can be interpreted as a nonlinear resonance characteristic, which represents a variation of an ‘‘output’’ amplitude versus detuning (i.e., A versus ␦ ). The effect of detuning is normalized by ⑀ = 1/Q and increases with increasing Q . The equation can be easily solved graphically and indeed has been for the van der Pol nonlinearity as shown in the Figure 2.13. To this author’s knowledge it has been applied to general circuits only in [48] with the Meissner oscillator as an example. Here we repeat the reasoning of [48] enhanced by three-dimensional plots and illustrated by the oscillator with cross-coupled BJTs. Figure 2.13(d) was derived by van der Pol [49] and is often cited in advanced texts on nonlinear oscillations [14, 15, 44]. It is shown here chiefly for reference purposes and as an illustration of the simple fact that the characteristics obtained for fixed detuning [Figure 2.13(c)] and those obtained for fixed external signal [Figure 2.13(d)] are just two aspects of the threedimensional relationship between A , B, and ␦ /⑀ shown in Figure 2.13(b). Figure 2.14 is of real interest to us. It clearly shows the locking conditions of our oscillator. These conditions are determined by the resonator’s
46
RF and Microwave Oscillator Design
Figure 2.13 Nonlinear resonance characteristics for van der Pol equation: (a) nonlinear characteristics i = G (v − v 3 /3), (b) relationship between oscillations and external signal amplitudes and detuning, given by (2.32), (c) a cross section of (b) for fixed detuning, and (d) contour lines of (b) for fixed B.
quality factor and by the nonlinear characteristics of the active circuit shown in Figure 2.14(a). The relationship between oscillations and external signal amplitudes and detuning, given by (2.32), is shown in three dimensions in Figure 2.14(b). From it we can graphically determine solutions of (2.32) (i.e., the dependence of amplitudes of locked oscillations on the amount of detuning and on the strength of the external signal). The relationship for fixed detuning is shown in Figure 2.14(c); the one for the fixed external signal is shown in Figure 2.14(d). The latter is shown for positive ␦ ; the contours for negative ␦ are the mirror image of those of Figure 2.14(d). They can be interpreted as a nonlinear resonance characteristic. The ‘‘inverted vase’’ shapes of the contours obtained for small B are clearly related to the shape of I (A ). The value of A 0 = 0.8 for which I (A 0 ) = 0 corresponds to the center of the ‘‘vase;’’ the value A 1 ≈ 0.18 for which I (A ) reaches maximum to the ‘‘neck’’ of our ‘‘vase.’’
Methods of Oscillator Design
47
Figure 2.14 Nonlinear resonance characteristics for the oscillator with cross-coupled BJTs: (a) the nonlinear characteristics i n (v ); (b) the relationship between oscillations and external signal amplitudes and detuning, given by (2.32); (c) a cross-section of (b) for fixed detuning; and (d) contour lines of (b) for fixed B.
Figures 2.14(c) and 2.14(d) provide a simple geometrical way to solve (2.32). They clearly show that for small values of B and ␦ , (2.32) has multiple solutions. For large B and ␦ , when A 2␦ 2 dominates I (A 2 ), the plots become monotonic and only one solution exists. So far we do not know which of the graphically found solutions are stable. It turns out that stability can be deduced from Figure 2.14, namely that the stable oscillations correspond to the upper parts of resonance characteristics in Figure 2.14(d), which decrease when ␦ grows. Indeed, the stability of a steady-state solution can be determined from (2.28) linearized about its constant solution A 0 , 0 : ⌬A˙ = −⑀ I ′(A 0 ) ⌬A + ⑀ B sin ( 0 ) ⌬ ⌬˙ = −⑀
B sin ( 0 ) A 20
⌬A + ⑀
B cos ( 0 ) ⌬ A0
48
RF and Microwave Oscillator Design
Since A 0 , 0 is a solution of (2.28), we get
␦ A 0 = ⑀ B sin 0 Consequently,
冋 册 冋 ⌬A˙ ⌬˙
=
−⑀ I ′(A 0 ) −␦ /A 0
册 冋 册
␦A0 ⌬A = −⑀ I (A 0 )/A 0 ⌬
The solution is stable when the trace of the matrix is negative and the determinant positive, that is, when I ′(A 0 ) + I (A 0 )/A 0 > 0
(2.33a)
⑀ 2I ′(A 0 ) I (A 0 )/A 0 + ␦ 2 > 0
(2.33b)
and
Now, from (2.32), the gradient B 2 with respect to (A , ␦ /⑀ ) equals [∂B /∂A , ∂B 2/∂(␦ /⑀ )] = [2I ′(A ) I (A ) + 2A␦ 2/⑀ 2, 2A 2␦ /⑀ ]. Consequently, the condition (2.33b) is satisfied when the gradient points upward (toward growing A ) in Figure 2.14(d). In other words, the condition is satisfied on the downsloped (A decreases when | ␦ | grows) parts of the contours. The first condition (2.33a) is expressed in terms of I (A ) and its derivative. It is shown in Figure 2.15. Since I (A ) is negative for small A and reaches minimum at A 1 ≈ 0.18 and zero at A 0 = 0.8, the expression I ′(A ) + I (A )/A is certainly negative for A < A 1 and positive for A > A 0 ; in between I ′(A ) + I (A )/A , it grows monotonically and crosses zero at A 2 ≈ 0.42, as shown in Figure 2.15. Thus, the locked oscillations are stable if their amplitude is larger than A 2 ≈ 0.42 and the corresponding detuning lies on the sloping down parts (A decreases when ␦ grows) of the contours in Figure 2.14(d). 2
2.7 Summary We have reviewed analysis methods for two classes of nonlinear oscillators: LC and high-Q. The first class relies on phase-plane analysis and provides insight into the global dynamics of the circuit. The second deals with oscilla-
Methods of Oscillator Design
49
Figure 2.15 Determination of the sign of I ′(A ) + I (A )/A : (a) I ′(A ) + I (A )/A is shown in a continuous line and its components I ′(A ), I (A )/A are shown in dotted lines and (b) same plots in zoomed in vertical scale, for reference I (A ) is shown in the thin line.
tions that are close to sinusoidal with the amplitude and phase either constant or slowly varying. Consequently, the behavior of the amplitude and phase determines the oscillations in the circuit. If an approximate solution is found, then the existence of the exact one is proven and the error estimated. The methods presented are all rigorous; references to theorems and to their proofs are included in Appendices 2A–2D. Most of the methods discussed here are not new; some of them can be traced to van der Pol’s intuition from the early 1930s and to the works of Krylov, Bogoliubov, Mitropolski, and Hale from the period 1930–1960. The latter were hardly available to circuit design. For that reason we have chosen a commonly used circuit as an illustration of different approaches. Our approach is related to the works of Pierce, Edson, and Kurokawa described in Chapter 1, which are general and applicable to microwave diode
50
RF and Microwave Oscillator Design
oscillators, although they are not as rigorous as [1–3, 6]. Extensive analysis focused on classical equations can be found in [14, 15, 44]. The linear theory of oscillations is only mentioned in Section 2.3. The rest of that section clarifies a common abuse of stability criterion. We have not discussed phase-noise analysis. Chapter 3 and sections of Chapter 4 are devoted to that important topic. We also did not discuss bifurcation phenomena (either in terms of onset of oscillation or transition to ‘‘chaos’’), which are out of the scope of this chapter. The interested reader may wish to consult [5, 50–52].
References [1]
Bogoliubov, N. N., and Y. A. Mitropolski, Asymptotic Methods in the Theory of Nonlinear Oscillations, New York: Gordon and Breach, 1961.
[2]
Hale, J. K., Ordinary Differential Equations, 2nd ed., Huntington, NY: Krieger, 1980.
[3]
Hale, J., Oscillations in Nonlinear Systems, New York: Dover, 1992.
[4]
Levi, M., ‘‘Qualitative Analysis of the Periodically Forced Relaxation Oscillations,’’ Ph.D. thesis, Department of Mathematics, Duke University, 1978.
[5]
Mees, A., Dynamics of Feedback Systems, New York: John Wiley and Sons, 1981.
[6]
Mitropolskii, Yu A., and O. B. Lykova, Integral Manifolds in Nonlinear Mechanics (in Russian), Moscow, Russia: Nauka, 1973.
[7]
Pederson, D. O., ‘‘A Historical Review of Circuit Simulation,’’ IEEE Trans. on Circuits and Systems, Vol. CAS-31, January 1984, pp. 103–111.
[8]
Hajimiri, A., and T. Lee, The Design of Low Noise Oscillators, Boston, MA: Kluwer, 1999.
[9]
Larson, L., RF and Microwave Circuit Design, Norwood, MA: Artech House, 1996.
[10]
Wu, H., and A. Hajimiri, ‘‘Silicon-Based Distributed Voltage-Controlled Oscillators,’’ IEEE Journal of Solid State Circuits, Vol. 36, No. 3, March 2001.
[11]
Andronov, A. A., A. A. Vitt, and S. E. Khaykin, Theory of Oscillations, New York: Dover, 1987.
[12]
Coddington, E. A., and N. Levison, Theory of Ordinary Differential Equations, Malabar, FL: Krieger, 1984.
[13]
Reissig, R., G. Sansone, and R. Conti, Nonlinear Theory of Nonlinear Differential Equations (in Russian), Moscow, Russia: Nauka, 1974.
[14]
Hayashi, C., Nonlinear Oscillations in Physical Systems, New York: McGraw-Hill, 1964.
[15]
Stoker, J. J., Nonlinear Vibrations in Mechanical and Electrical Systems, New York: John Wiley and Sons, 1992.
[16]
Odyniec, M., and L. O. Chua, ‘‘Integral Manifolds for Nonlinear Circuits,’’ Intl. Journal of Circuit Theory and Applications, Vol. 12, 1984, pp. 293–328.
Methods of Oscillator Design
51
[17]
Guckenheimer, J., ‘‘Dynamics of the van der Pol Equation,’’ IEEE Trans. on Circuits and Systems, Vol. CAS-27, November 1980.
[18]
Jackson, R. T., ‘‘Criteria for the Onset of Oscillations in Microwave Circuits,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. MTT-40, March 1992, pp. 566–568, ‘‘Comments on Criteria . . . ,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. MTT-40, September 1992, pp. 1850–1851.
[19]
Khanna, A. P. S., ‘‘Oscillators,’’ Chapter 9 of Microwave Solid State Circuit Design, I. Bahl and P. Bhartia (eds.), New York: John Wiley and Sons, 1988.
[20]
Krauss, H. L., C. W. Bostian, and F. H. Raab, Solid State Radio Engineering, New York: John Wiley and Sons, 1980.
[21]
Martin, J. L. J., and F. J. O. Gonzalez, ‘‘Accurate Linear Oscillator Analysis and Design,’’ Microwave Journal, June 1996.
[22]
Matthys, R. J., Crystal Oscillator Circuits, New York: John Wiley and Sons, 1983, and Malabar, FL: Krieger, 1992.
[23]
Rhea, R., Oscillator Design and Computer Simulation, 2nd ed., Atlanta, GA: Noble Publishing, 2000.
[24]
Vendelin, G. D., U. L. Rohde, and A. M. Pavio, Microwave Circuit Design Using Linear and Nonlinear Techniques, New York: John Wiley and Sons, 1990.
[25]
Abrie, P., Design of RF and Microwave Amplifiers and Oscillators, Norwood, MA: Artech House, 1999.
[26]
Boyles, J. W., ‘‘The Oscillator as a Reflection Amplifier,’’ Microwave Journal, June 1986.
[27]
Camargo, E., Design of FET Frequency Multipliers and Harmonic Oscillators, Norwood, MA: Artech House, 1998.
[28]
Nativ, Z., and Y. Shur, ‘‘Push-Push VCO Design with CAD Tools,’’ Microwave Journal, February 1989.
[29]
Przedpelski, A., ‘‘Simple, Low Cost UHF VTOs,’’ RF Design, May 1993.
[30]
Ratier, N., et al., ‘‘Automatic Formal Derivation of the Oscillation Condition,’’ IEEE Int. Frequency Control Symp., 1997.
[31]
Razban, T., et al., ‘‘A Compact Oscillator,’’ Microwave Journal, February 1994.
[32]
Savaria, S., and P. Champagne, ‘‘Linear Simulators,’’ Microwave Journal, May 1995.
[33]
Schiebold, C., ‘‘Getting Back to the Basics of Oscillator Design,’’ Microwave Journal, May 1998.
[34]
Sweet, A., MIC and MMIC Amplifier and Oscillator Circuit Design, Norwood, MA: Artech House, 1990.
[35]
Warren, D., et al., ‘‘Large and Small Signal Oscillator Analysis,’’ Microwave Journal, May 1989.
[36]
Basawapatna, G. R., and R. B. Stancliff, ‘‘A Unified Approach to the Design of WideBand Microwave Solid State Oscillators,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. MTT-27, May 1979, pp. 379–385.
[37]
D’Azzo, J. J., and C. H. Houpis, Feedback Control System Analysis and Synthesis, New York: McGraw-Hill, 1960.
52
RF and Microwave Oscillator Design
[38]
Odyniec, M., ‘‘Stability Criteria Via S-Parameters,’’ EuMC’95, Bologna, Italy, September 1995 (also ‘‘Oscillator Stability Analysis,’’ Microwave Journal, June 1999).
[39]
Kundert, K., Steady State Methods for Simulating Analog and Microwave Circuits, Boston, MA: Kluwer, 1995.
[40]
Kudrewicz, J., ‘‘Frequency Methods’’ (in Polish), WNT, 1972.
[41]
Kudrewicz, J., ‘‘Contribution to the Theory of Weakly Nonlinear Oscillators,’’ Intl. Journal of Circuit Theory and Applications, Vol. 4, 1976, pp. 161–176.
[42]
Kurokawa, K., An Introduction to the Theory of Microwave Circuits, New York: Academic Press, 1969.
[43]
Kurokawa, K., ‘‘Some Basic Characteristics of Broadband Negative Resistance Oscillator Circuits,’’ Bell System Technical Journal, July–August 1969, pp. 1937–1955.
[44]
Minorsky, N., Nonlinear Oscillations, Huntington, NY: Krieger, 1974.
[45]
Odyniec, M., and W. Overstreet, ‘‘New Applications of Harmonic Balance Analysis,’’ Intl. Journal on Microwave and Millimeter-Wave CAE, May 1995.
[46]
Ngoya, E., and R. Larcheveque, ‘‘Envelope Transient,’’ MTTS’1996, San Francisco, CA, June 1996.
[47]
Sharrit, D., ‘‘New Method of Analysis of Communication Systems,’’ Workshop on Nonlinear CAD, MTTS’1996, San Francisco, CA, June 17, 1996.
[48]
Odyniec, M., ‘‘Nonlinear Synchronized LC Oscillators,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. MTT-41, No. 5, May 1993, pp. 774–780.
[49]
van der Pol, B., ‘‘The Nonlinear Theory of Electric Oscillators,’’ Proc. IRE, Vol. 22, No. 9, September 1934.
[50]
DeFeo, O., G. M. Maggio, and M. P. Kennedy, ‘‘The Colpitts Oscillator: Families of Periodic Solutions and Their Bifurcations,’’ Intl. Journal Bifurcation and Chaos, March 2000.
[51]
Palazuelos, E., et al., ‘‘Hysteresis Prediction in Autonomous Microwave Circuits Using Commercial Software, Application to a Ku Band MMIC VCO,’’ IEEE Journal of Solid-State Circuits, Vol. 33, No. 8, August 1998, pp. 1239–1243.
[52]
Ver Hoeye, S., A. Sua´rez, and S. Sancho, ‘‘Analysis of Noise Effects on the Nonlinear Dynamics of Synchronized Oscillators,’’ IEEE Microwave and Wireless Components Letters, Vol. 11, No. 9, September 2001.
Appendix 2A: Nyquist Stability Criterion Consider a feedback system with two linear blocks, one the ‘‘filter’’ with transfer function ‘‘H (s ),’’ the other the ‘‘amplifier’’ G (s ). According to the Nyquist stability criterion [37], the number of the right-hand plane poles of the feedback system equals the number of the right-hand plane poles of H (s ) G (s ) plus the number of the clockwise encirclement of 1 + j 0 by H ( j ) G ( j ). When H (s ) G (s ) has no poles in the right half plane, then the encirclements of 1 + j 0 determine the stability of the system. The above
Methods of Oscillator Design
53
remains valid for any transfer function, in particular when H (s ) G (s ) is replaced by Yn (s ) Zr (s ) or Sr (s ) Sn (s ). For resonators with high Q one can modify the Nyquist criterion as follows: If the resonator has high Q, then the dependence of G on frequency can be neglected and it suffices to check whether H ( j ) encircles 1/G + j 0 [rather than GH ( j ) encircling 1 + j 0]. The Nyquist loop as well as the magnitude and the phase of the transfer function can be easily plotted with commercially available software.
Appendix 2B: Justification of the Describing Function Method Consider an oscillator circuit described by an integral equation ∞
v (t ) =
冕
h ( ) f (v (t − )) d
(2B.1)
0
Periodic solutions of (2B.1) can be expanded into a Fourier series: ∞
v (t ) =
∑
k = −∞
v k e jk t, f (v (t )) =
∞
∑
k = −∞
f k (v 0 , v 1 , v 2 , . . . ) e jk t
the coefficients of which can be found from the equation: v k = H (k ) f k (v 0 , v 1 , v 2 , . . . )
(2B.2)
where ∞
H ( ) =
冕
h (t ) e jk t dt
−∞
T
1 f k (v 0 , v 1 , v 2 , . . . ) = 2T
冕 冢∑ ∞
f
−T
k = −∞
冣
v k e jk t e −jk t dt
where H ( ) is the ‘‘filter’’ characteristic and h (t ) is its impulse response; f is the nonlinear element. We use an integral equation to describe the system
54
RF and Microwave Oscillator Design
because in that case we include filters with distributed elements. In particular, a lumped system described by the ordinary differential equation K
∑ ak
k=0
冉冊
k
d v= dt
L
∑ bl
l=0
冉冊 l
d f (v (t )) dt
is a special case of (2B.1) with L
H ( ) =
⁄
K
∑ b l ( j ) ∑ a k ( j )k l
l=0
k=0
After neglecting all harmonics except the first, we obtain: v 1 = H ( ) f 1 (0, v 1 , 0, . . . )
(2B.3)
Since v 1 is real, we rewrite (2B.3) as: A = H ( ) F (A ) where
(2B.4)
2v 1 = A T
冕
1 f 1 (0, v 1 , 0, 0) = 2T
=
1
f (v 1 e j t + v −1 e −j t ) e −j t dt
−T
冕
f (A cos ) cos d = F (A )/2
0
The following theorem is proven in [40]. Theorem (Kudrewicz). If the following conditions hold:
(a) Equation (B2.4) possesses a solution A , ϖ that persists under small perturbations. (b) The active circuit characteristic is bounded and has bounded slope ∃ M > 0 ∃ L > 0 ∀A | F (A ) | < M , | dF (A )/dA | < L
Methods of Oscillator Design
55
(c) The ‘‘filter’’ is selective ∃ > 0 ∀k ≠ 1 | H (k ) | < . Then the exact equation also possesses a periodic solution ∞
v (t ) =
∑
k = −∞
v k e jk t, i (t ) =
∞
∑
k = −∞
i k e jk t
(2B.5)
which is close to the approximate one: v˜ (t ) = A cos (ϖ t )
(2B.6)
More exactly:
| v1 − A | < d , | − ϖ | < ,
∞
∑ | vk | 2 < 2
(2B.7)
|k |≠1
where d , , and are small numbers that depend on M , L , and from conditions (b) and (c) above. They estimate the errors in the amplitude of the fundamental (d), frequency ( ), and the harmonic distortion ( ). Outline of the proof. Consider (2B.2) without 1 of k = 1. Thus, we get an equation in ‘‘sequence space’’ l 2 with variables v k , k = 0, 2, 3, . . . and with v 1 = A /2 and as parameters:
v k = H (k ) f k (v 0 , A /2, v 2 , . . . ), k = 0, 2, 3, . . .
(2B.8)
Since H ( ) is selective (i.e., | H (k ) | is small for k = 0, 2, 3, . . . ) and f has a bounded slope, it follows from the theorem of contraction mapping that for any A and , (2B.8) has a unique and small solution v k = v k (A , ), k = 0, 2, 3, . . . . Substituting this solution into the equation with k = 1, we get: A = 2H ( ) f 1 (v 0 (A , ), A /2, v 2 (A , ), . . . )
(2B.9)
Since v k = v k (A , ) are small for k = 0, 2, 3, . . . , (2B.9) is a small perturbation of (2B.4). Consequently, the existence of a solution A , ϖ of (2B.4) that persists under small perturbations causes the existence of solution of (2B.9), and the two solutions remain close.
56
RF and Microwave Oscillator Design
Appendix 2C: Transformation of Voltage-Current to Amplitude-Phase Equations Our oscillator with the external source is described by: di L =v dt
L
(2C.1)
dv = −i L − i n (v ) − B cos t dt
C
If the circuit has high Q and the waveforms are close to sinusoidal, then it is convenient to perform the transformation of variables from voltagecurrent v, i L to amplitude-phase A , v (t ) = A (t ) cos ( t + (t )) i L (t ) =
(2C.2)
A (t ) sin ( t + (t )) L
Differentiated in time, (2C.2) reads: dv (t )/dt = A˙ cos ( t + ) − A sin ( t + )˙ − A sin ( t + ) Ldi L /dt = (A˙ / ) sin ( t + ) + (A / ) cos ( t + )˙ + A cos ( t + ) (2C.3) Consequently, (2C.1) transforms to: (A˙ / ) sin ( t + ) + (A / ) cos ( t + )˙ + A cos ( t + ) = A cos ( t + ) CA˙ cos ( t + ) − CA sin ( t + )˙ − CA sin ( t + ) = −(A / L ) sin ( t + ) − i n (A cos ( t + )) − B cos ( t ) which are linear in A˙ , ˙
冋
sin ( t + )/
(A / ) cos ( t + )
C cos ( t + )
−CA sin ( t + )
册冋 册 冋 册 A˙ ˙
=
0 f
(2C.4)
Methods of Oscillator Design
57
where f = 2AC␦ sin ( t + ) − i n (A cos ( t + )) − B cos ( t )
␦ = ( 2 − 20 )/2 ≈ − 0 Solving for A˙ , ˙ , we get 1 A˙ = [2AC␦ sin ( t + ) − i n (A cos ( t + )) C − B cos ( t )] cos ( t + )
˙ = −
(2C.5)
1 [2AC␦ sin ( t + ) − i n (A cos ( t + )) AC
− B cos ( t )] sin ( t + ) after accounting for cos ( t ) sin ( t + ) = [sin (2 t + ) + sin ( )] cos ( t ) cos ( t + ) = [cos (2 t + ) + cos ( )] and averaging the terms explicitly dependent on time, we get: A˙ = −I (A )/C − (B /C ) cos
˙ = −␦ +
(2C.6)
1 B sin AC
In case of the free-running oscillator B = 0, we apply the transformation (2C.2) with = 0 where 0 = 1/√LC is the natural frequency of the circuit. Consequently, we get the final equations with B = 0, ␦ = 0: A˙ = −I (A )/C
(2C.7)
˙ = 0 Note that (2C.7) yields a constant phase and the same constant amplitude as the one obtained from the describing function method. It provides us with the information of the varying amplitude of Figure 2.12; in particular, it clearly shows the stability of the constant amplitude.
58
RF and Microwave Oscillator Design
Appendix 2D: Theorems on Averaging Many practical problems (including the original van der Pol analysis of oscillators) lead to x˙ = ⑀ X (x , t )
(2D.1)
where X (x , t ) is T-periodic in t . When averaged in time, (2D.1) can be reduced to x˙ = ⑀ X 0 (x )
(2D.2)
T
1 where X 0 (x ) = T
冕
X (x , t ) dt . Equation (2D.2) is called the averaged
0
equation. Two theorems hold: 1. Theorem 1 (transient behavior): If the solutions of (2D.1) and (2D.2) originate from the same initial condition and the parameter ⑀ is ‘‘small,’’ then they remain ‘‘close’’ over the time interval proportional to 1/⑀ . 2. Theorem 2 (steady-state): If (2D.2) possesses a constant regular solution x 0 and the parameter ⑀ is ‘‘small,’’ then (2D.1) possesses a T-periodic solution x (t ) that remains ‘‘close’’ to x 0 . Moreover, if x 0 is asymptotically stable, so is x (t ).
Acknowledgments I gratefully acknowledge the works of Jacek Kudrewicz, Jack Hale, Kaneyuki Kurokawa, and the Kiev school of qualitative analysis of nonlinear systems on which this chapter is based. I wish to dedicate it to Jacek Kudrewicz, who introduced me to oscillator analysis.
3 Linearity, Time Variation, and Oscillator Phase Noise Thomas H. Lee and Ali Hajimiri 3.1 Introduction The theoretical and practical importance of oscillators has motivated the development of numerous treatments of phase noise. The sheer number of publications on this topic underscores the importance attached to it. At the same time, many of these disagree on rather fundamental points, and it may be argued that the abundance of such conflicting research quietly testifies to the inadequacies of many of those treatments. Complicating the search for a suitable theory is that noise in a circuit may undergo frequency translations before ultimately becoming oscillator phase noise. These translations are often attributed to the presence of obvious nonlinearities in practical oscillators. The simplest theories nevertheless simply ignore the nonlinearities altogether and frequently ignore the possibility of time variation as well. Such linear, time-invariant (LTI) theories surprisingly manage to provide important qualitative design insights. However, these theories are understandably limited in their predictive power. Chief among the deficiencies of an LTI theory is that frequency translations are necessarily disallowed, begging the question of how the (nearly) symmetrical sidebands observed in practical oscillators can arise. Despite this complication, and despite the obvious presence of nonlinearities necessary for amplitude stabilization, the noise-to-phase transfer 59
60
RF and Microwave Oscillator Design
function of oscillators nonetheless may be treated as linear. However, a quantitative understanding of the frequency translation process requires abandonment of the principle of time invariance implicitly assumed in most theories of phase noise. In addition to providing a quantitative reconciliation between theory and measurement, the time-varying phase noise model presented here identifies an important symmetry principle, which may be exploited to suppress the upconversion of 1/f noise into close-in phase noise. At the same time, it provides an explicit accommodation of cyclostationary effects, which are significant in many practical oscillators, and of amplitudeto-phase (AM-PM) conversion as well. These insights allow a reinterpretation of why certain topologies, such as the Colpitts oscillator, exhibit good performance. Perhaps more important, the theory informs design, suggesting novel optimizations of well-known oscillators, as well as the invention of new circuit topologies. Tuned LC and ring oscillator circuit examples are presented to reinforce the theoretical considerations developed. Simulation issues and the topic of amplitude noise are considered as well. We first revisit how one evaluates whether a system is linear or timeinvariant. Indeed, we find that we must even take care to define explicitly what is meant by the word ‘‘system.’’ We then identify some very general tradeoffs among key parameters, such as power dissipation, oscillation frequency, resonator Q , and circuit noise power. These tradeoffs are first studied qualitatively in a hypothetical ideal oscillator in which linearity of the noiseto-phase transfer function is assumed, allowing characterization by an impulse response. Although the assumption of linearity is defensible, we shall see that time invariance fails to hold even in this simple case. That is, oscillators are linear, time-varying (LTV) systems, where ‘‘system’’ is defined by the noise-to-phase transfer characteristic. Fortunately, complete characterization by an impulse response depends only on linearity, not time invariance. By studying the impulse response, we discover that periodic time variation leads to frequency translation of device noise to produce the phase noise spectra exhibited by real oscillators. In particular, the upconversion of 1/f noise into close-in phase noise is seen to depend on symmetry properties that are potentially controllable by the designer. Additionally, the same treatment easily subsumes the cyclostationarity of noise generators, and helps explain why class-C operation of active elements within an oscillator can be beneficial. Illustrative circuit examples reinforce key insights of the LTV model. In general, circuit and device noise can perturb both the amplitude and phase of an oscillator’s output. Because amplitude fluctuations are usually greatly attenuated as a result of the amplitude stabilization mechanisms present in every practical oscillator, phase noise generally dominates, at least
Linearity, Time Variation, and Oscillator Phase Noise
61
at frequencies not far removed from the carrier. Thus, even though it is possible to design oscillators in which amplitude noise is significant, we focus primarily on phase noise here. We show later that a simple modification of the theory allows the accommodation of amplitude noise as well, permitting the accurate computation of output spectrum at frequencies well removed from the carrier.
3.2 General Considerations Perhaps the simplest abstraction of an oscillator that still retains some connection to the real world is a combination of a lossy resonator and an energy restoration element. The latter precisely compensates for the tank loss to enable a constant-amplitude oscillation. To simplify matters, assume that the energy restorer is noiseless (see Figure 3.1). The tank resistance is therefore the only noisy element in this model. To gain some useful design insight, first compute the signal energy stored in the tank: E2 =
1 2 CV pk 2
(3.1)
so that the mean-square signal (carrier) voltage is: 2 V sig =
E stored C
(3.2)
where we have assumed a sinusoidal waveform. The total mean-square noise voltage is found by integrating the resistor’s thermal noise density over the noise bandwidth of the RLC resonator:
Figure 3.1 ‘‘Perfectly efficient’’ RLC oscillator.
62
RF and Microwave Oscillator Design ∞
V n2
= 4kTR
冕| |
2 kT Z( f ) 1 = df = 4kTR R 4RC C
(3.3)
0
Combining (3.2) and (3.3), we obtain a noise-to-carrier ratio (the reason for this ‘‘upside-down’’ ratio is simply one of convention): kT N V n2 = = C E 2 stored V sig
(3.4)
Sensibly enough, one therefore needs to maximize the signal levels to minimize the noise-to-carrier ratio. We may bring power consumption and resonator Q explicitly into consideration by noting that Q can be defined generally as proportional to the energy stored, divided by the energy dissipated: Q=
0 E stored P diss
(3.5)
Therefore, N 0 kT = C QP diss
(3.6)
The power consumed by this model oscillator is simply equal to P diss , the amount dissipated by the tank loss. The noise-to-carrier ratio is here inversely proportional to the product of resonator Q and the power consumed, and directly proportional to the oscillation frequency. This set of relationships still holds approximately for real oscillators and explains the near obsession of engineers with maximizing resonator Q , for example. Other important design criteria become evident by coupling the foregoing with additional knowledge of practical oscillators. One is that oscillators generally operate in one of two regimes that may be distinguished by their differing dependence of output amplitude on bias current (see Figure 3.2), so that one may write Vsig = I BIAS R
(3.7)
Linearity, Time Variation, and Oscillator Phase Noise
63
Figure 3.2 Oscillator operating regimes.
where R is a constant of proportionality with the dimensions of resistance. This constant, in turn, is proportional to the equivalent parallel tank resistance [1], so that Vsig ⬀ I BIAS R tank
(3.8)
implying that the carrier power may be expressed as P sig ⬀ (I BIAS R tank )2
(3.9)
The noise power has already been computed in terms of the tank capacitance as V n2 =
kT C
(3.10)
but it may also be expressed in terms of the tank inductance: V n2 =
kT = C
kT 1
冉 冊
= kT 20 L
(3.11)
20 L
An alternative expression for the noise-to-carrier ratio in the currentlimited regime is therefore
64
RF and Microwave Oscillator Design
kT 0 L N ⬀ C (I BIAS R tank )2
(3.12)
Assuming operation at a fixed supply voltage, a constraint on power consumption implies an upper bound on the bias current. Of the remaining free parameters, then, only the tank inductance and resistance may be practically varied to minimize the N /C ratio. That is, optimization of such an oscillator corresponds to minimizing L /(R tank )2. In many treatments, maximizing tank inductance is offered as a prescription for optimization. However, we see that a more valid objective is to minimize L /(R tank )2 [2]. Since, in general, the resistance is itself a function of inductance, identifying (and then achieving) this minimum is not always trivial. An additional consideration is that, below a certain minimum inductance, oscillation may cease. Hence, the optimization prescription here presumes oscillation, and in a regime where the output amplitude is proportional to the bias current.
3.3 Detailed Considerations: Phase Noise To augment the qualitative insights of the foregoing analysis, let us now determine the actual output spectrum of the ideal oscillator. 3.3.1 Phase Noise of an Ideal Oscillator Assume that the output in Figure 3.1 is the voltage across the tank, as shown. By postulate, the only source of noise is the white thermal noise of the tank conductance, which we represent as a current source across the tank with a mean-square spectral density of i n2 = 4kTG ⌬f
(3.13)
This current noise becomes voltage noise when multiplied by the effective impedance facing the current source. In computing this impedance, however, it is important to recognize that the energy restoration element must contribute an average effective negative resistance that precisely cancels the positive resistance of the tank. Hence, the net result is that the effective impedance seen by the noise current source is simply that of a perfectly lossless LC network.
Linearity, Time Variation, and Oscillator Phase Noise
65
For a relatively small offset frequency ⌬ from the center frequency 0 , the impedance of an LC tank may be approximated by Z ( 0 + ⌬ ) ≈ j
0L ⌬ 2 0
(3.14)
We may write the impedance in a more useful form by incorporating an expression for the unloaded tank Q : Q=
1 R = 0 L 0 GL
(3.15)
Solving (3.15) for L and substituting into (3.14) yield: 1
| Z ( 0 + ⌬ ) | ≈ G
0 2Q | ⌬ |
(3.16)
Thus, we have traded an explicit dependence on inductance for a dependence on Q and G. Next, multiply the spectral density of the mean-square noise current by the squared magnitude of the tank impedance to obtain the spectral density of the mean-square noise voltage:
冉
v n2 i2 0 2 = n | Z | = 4kTR ⌬f ⌬f 2Q ⌬
冊
2
(3.17)
The power spectral density of the output noise is frequency-dependent because of the filtering action of the tank, falling as the inverse-square of the offset frequency. This 1/f 2 behavior simply reflects the fact that the voltage frequency response of an RLC tank rolls off as 1/f to either side of the center frequency, and that power is proportional to the square of voltage. Note also that an increase in tank Q reduces the noise density, when all other parameters are held constant, underscoring once again the value of increasing resonator Q . In our idealized LC model, thermal noise affects both amplitude and phase, and (3.17) includes their combined effect. The equipartition theorem of thermodynamics tells us that, in equilibrium, amplitude and phase noise
66
RF and Microwave Oscillator Design
power are equal. Therefore, the amplitude-limiting mechanism present in any practical oscillator suppresses half the noise given by (3.17). It is traditional to normalize the mean-square noise voltage density to the mean-square carrier voltage, and report the ratio in decibels, thereby explaining the ‘‘upside down’’ ratios presented previously. Performing this normalization yields the following equation for phase noise:
冋 冉
2kT 0 L {⌬ } = 10 log P sig 2Q ⌬
冊册 2
(3.18)
The units of phase noise are thus proportional to the log of a density. Specifically, they are commonly expressed as ‘‘decibels below the carrier per hertz,’’ or dBc/Hz, specified at a particular offset frequency ⌬ from the carrier frequency 0 . For example, one might speak of a 2-GHz oscillator’s phase noise as ‘‘−110 dBc/Hz at a 100-kHz offset.’’ It is important to note that the ‘‘per Hz’’ actually applies to the argument of the log, not to the log itself; doubling the measurement bandwidth does not double the decibel quantity. As lacking in rigor ‘‘dBc/Hz’’ is, it is common usage [1]. Equation (3.18) tells us that phase noise (at a given offset) improves as both the carrier power and Q increase, as predicted earlier. These dependencies make sense. Increasing the signal power improves the ratio simply because the thermal noise is fixed, while increasing Q improves the ratio quadratically because the tank’s impedance falls off as 1/Q ⌬ . Because many simplifying assumptions have led us to this point, it should not be surprising that there are some significant differences between the spectrum predicted by (3.18) and what one typically measures in practice. For example, although real spectra do possess a region where the observed density is proportional to 1/(⌬ )2, the magnitudes are typically quite a bit larger than predicted by (3.18), because there are additional important noise sources besides tank loss. For example, any physical implementation of an energy restorer will be noisy. Furthermore, measured spectra eventually flatten out for large frequency offsets, rather than continuing to drop quadratically. Such a floor may be due to the noise associated with any active elements (such as buffers) placed between the tank and the outside world, or it can even reflect limitations in the measurement instrumentation itself. Even if the output were taken directly from the tank, any resistance in series with either the inductor or capacitor would impose a bound on the amount of filtering provided by the tank at large frequency offsets and thus ultimately
Linearity, Time Variation, and Oscillator Phase Noise
67
produce a noise floor. Finally, there is almost always a 1/(⌬ )3 region at small offsets. A modification to (3.18) provides a means to account for these discrepancies:
冋 再冉
2FkT L {⌬ } = 10 log P sig
0 1+ 2Q ⌬
冊 冎冉 2
1+
⌬ 1/f
| ⌬ |
3
冊册
(3.19)
These modifications, due to Leeson, consist of a factor F to account for the increased noise in the 1/(⌬ )2 region, an additive factor of unity (inside the braces) to account for the noise floor, and a multiplicative factor (the term in the second set of parentheses) to provide a 1/ | ⌬ | 3 behavior at sufficiently small offset frequencies [3]. With these modifications, the phase noise spectrum appears as in Figure 3.3. It is important to note that the factor F is an empirical fitting parameter and therefore must be determined from measurements, diminishing the predictive power of the phase noise equation. Furthermore, the model asserts that ⌬ 1/f 3, the boundary between the 1/(⌬ )2 and 1/ | ⌬ | 3 regions, is precisely equal to the 1/f corner of device noise. However, measurements frequently show no such equality, and thus one must generally treat ⌬ 1/f 3 as an empirical fitting parameter as well. Also it is not clear what the corner frequency will be in the presence of more than one noise source, each with an individual 1/f noise contribution (and generally differing 1/f corner frequencies). Finally, the frequency at which the noise flattens out is not always equal to half the resonator bandwidth, 0 /2Q .
Figure 3.3 Phase noise: Leeson versus (3.18).
68
RF and Microwave Oscillator Design
Both the ideal oscillator model and the Leeson model suggest that increasing resonator Q and signal power are ways to reduce phase noise. The Leeson model additionally introduces the factor F, but without knowing precisely what it depends on, it is difficult to identify specific ways to reduce it. The same problem exists with ⌬ 1/f 3 as well. Finally, blind application of these models has periodically led to earnest but misguided attempts by some designers to use active circuits to boost Q . Sadly, increases in Q through such means are necessarily accompanied by increases in F as well, generally preventing the anticipated improvements in phase noise. Again, the lack of analytical expressions for F can obscure this conclusion, and one continues to encounter various doomed oscillator designs based on the notion of active Q boosting. That neither (3.18) nor (3.19) can make quantitative predictions about phase noise is an indication that at least some of the assumptions used in the derivations are invalid, despite their apparent reasonableness. To develop a theory that does not possess the enumerated deficiencies, we need to revisit, and perhaps revise, these assumptions.
3.4 The Roles of Linearity and Time Variation in Phase Noise The foregoing derivations have all assumed linearity and time invariance. Let us reconsider each of these assumptions in turn. Nonlinearity is clearly a fundamental property of all real oscillators, as its presence is necessary for amplitude limiting. Several phase noise theories have consequently attempted to explain certain observations entirely as a consequence of nonlinear behavior. One of these observations is that a singlefrequency sinusoidal disturbance injected into an oscillator gives rise to two equal-amplitude sidebands, symmetrically disposed about the carrier [4]. Since LTI systems cannot perform frequency translation and nonlinear systems can, nonlinear mixing has often been proposed to explain phase noise. Unfortunately, the amplitude of the sidebands generally must then depend nonlinearly on the amplitude of the injected signal, and this dependency is not generally observed. One must conclude that memoriless nonlinearity cannot explain the discrepancies, despite initial attractiveness as the culprit. As we shall see momentarily, amplitude-control nonlinearities certainly do affect phase noise, but only indirectly, by controlling the detailed shape of the output waveform.
Linearity, Time Variation, and Oscillator Phase Noise
69
An important insight is that disturbances are just that: perturbations superimposed on the main oscillation. They will always be much smaller in magnitude than the carrier in any oscillator worth designing or analyzing. Thus, if a certain amount of injected noise produces a certain amount of phase disturbance, we ought to expect that doubling the injected noise will produce double the disturbance. Linearity would therefore appear to be a reasonable assumption as far as the noise-to-phase transfer function is concerned. It is therefore particularly important to keep in mind that, when assessing linearity, it is essential to identify explicitly the input-output variables. Linear relationships may exist between certain variable pairs at the same time nonlinear ones exist between others. This assumption of linearity is not equivalent to a neglect of the nonlinear behavior of the active devices. It is rather a linearization around the steady-state solution and therefore takes the effect of device nonlinearity into account. There is thus no contradiction here with the prior acknowledgment of nonlinear amplitude control. We see that the word system is actually ill-defined. Most take it to refer to an assemblage of components and their interconnections, but a more useful definition is based on the particular input-output variables chosen. With this definition, the same circuit may possess nonlinear relationships among certain variables and linear ones among others. Time invariance is also not an inherent property of the entire circuit; it is similarly dependent on the variables chosen. We are left only with the assumption of time invariance to reexamine. In the previous derivations, we have extended time invariance to the noise sources themselves, meaning that the measures that characterize noise (e.g., spectral density) are time-invariant (stationary). In contrast with linearity, the assumption of time invariance is less obviously defensible. In fact, it is surprisingly simple to demonstrate that oscillators are fundamentally timevarying systems. Recognizing this truth is the main key to developing a more accurate theory of phase noise [5]. To show that time invariance fails to hold, consider explicitly how an impulse of current affects the waveform of the simplest resonant system, a lossless LC tank (Figure 3.4). Assume that the system is oscillating with some constant amplitude until the impulse occurs; then consider how the system responds to an impulse injected at two different times, as seen in Figure 3.5. If the impulse happens to coincide with a voltage maximum (as in the left plot of Figure 3.5), the amplitude increases abruptly by an amount ⌬V = ⌬Q /C , but because the response to the impulse superposes exactly in phase with the preexisting oscillation, the timing of the zero crossings does not change. On the other hand, an impulse injected at some other time
70
RF and Microwave Oscillator Design
Figure 3.4 LC oscillator excited by current pulse.
Figure 3.5 Impulse responses of LC tank.
generally affects both the amplitude of oscillation and the timing of the zero crossings, as in the right-hand plot. Interpreting the zero-crossing timings as a measure of phase, we see that the amount of phase disturbance for a given injected impulse depends on when the injection occurs; time invariance thus fails to hold. An oscillator is therefore a linear but (periodically) timevarying system. It is especially important to note that it is theoretically possible to leave unchanged the energy of the system (as reflected in a constant tank amplitude), if the impulse injects at a moment near the zero crossing, such that the net work performed by the impulse is zero. For example, a small positive impulse injected when the tank voltage is negative extracts energy from the oscillator, and the same impulse injected when the tank voltage is positive delivers energy to the oscillator. Just before the zero crossing, an instant may be found where such an impulse performs no work at all. Consequently, the amplitude of oscillation cannot change, but the zero crossings will be displaced. Because linearity of noise-to-phase conversion remains a good assumption, the impulse response still completely characterizes that system, even with time variation. Noting that an impulsive input produces a step change in phase, the impulse response may be written as: h (t , ) =
⌫( 0 t ) u (t − ) q max
(3.20)
Linearity, Time Variation, and Oscillator Phase Noise
71
where u (t ) is the unit step function. Dividing by q max , the maximum charge displacement across the capacitor, makes the function ⌫(x ) independent of signal amplitude. ⌫(x ) is called the impulse sensitivity function (ISF), and is a dimensionless, frequency- and amplitude-independent function periodic in 2 . As its name suggests, it encodes information about the sensitivity of the oscillator to an impulse injected at phase 0 t . In the LC oscillator example, ⌫(x ) has its maximum value near the zero crossings of the oscillation, and a zero value at maxima of the oscillation waveform. In general, it is most practical (and most accurate) to determine ⌫(x ) through simulation, but there are also analytical methods (some approximate) that apply in special cases [6, 7]. In any event, to develop a feel for typical shapes of ISFs, consider two representative examples, first for an LC and a ring oscillator in Figure 3.6. Once the ISF has been determined (by whatever means), we may compute the excess phase through use of the superposition integral. This computation is valid here since superposition is linked to linearity, not time invariance: t
∞
(t ) =
冕
−∞
h (t , ) i ( ) d =
1 q max
冕
⌫( 0 ) i ( ) d
(3.21)
−∞
This computation can be visualized with the help of the equivalent block diagram shown in Figure 3.7.
Figure 3.6 Example ISF for (a) an LC oscillator and (b) a ring oscillator.
72
RF and Microwave Oscillator Design
Figure 3.7 The equivalent block diagram of the process.
To cast this equation in a more practically useful form, note that the ISF is periodic and therefore expressible as a Fourier series: ⌫( 0 ) =
c0 + 2
∞
∑ c n cos (n 0 + n )
(3.22)
n=1
where the coefficients c n are real, and n is the phase of the n th harmonic of the ISF. We will ignore n in all that follows because we will be assuming that noise components are uncorrelated, so that their relative phase is irrelevant. The value of this decomposition is that, like many functions associated with physical phenomena, the series typically converges rapidly, so that it is often well approximated by just the first few terms of the series. Substituting the Fourier expansion into (3.21), and exchanging summation and integration, one obtains: t
(t ) =
1 q max
冤 冕 c0 2
−∞
i ( ) d +
∞
∑ cn
n=1
t
冕
−∞
i ( ) cos (n 0 ) d
冥
(3.23)
The corresponding sequence of mathematical operations is shown graphically in the left half of Figure 3.8. Note that the block diagram contains elements that are analogous to those of a superheterodyne receiver. The normalized noise current is a broadband ‘‘RF’’ signal, whose Fourier components undergo simultaneous downconversions (multiplications) by ‘‘local oscillator’’ signals at all harmonics of the oscillation frequency. It is important to keep in mind that multiplication is a linear operation if one argument is held constant, as it is here. The relative contributions of these multiplications are determined by the Fourier coefficients of the ISF. Equation (3.23) thus allows us to compute the excess phase caused by an arbitrary noise current
Linearity, Time Variation, and Oscillator Phase Noise
73
Figure 3.8 The equivalent system for ISF decomposition.
injected into the system, once the Fourier coefficients of the ISF have been determined (typically through simulation). Earlier, we noted that signals (noise) injected into a nonlinear system at some frequency may produce spectral components at a different frequency. We now show that a linear, but time-varying system can exhibit qualitatively similar behavior, as implied by the superheterodyne imagery invoked in the preceding paragraph. To demonstrate this property explicitly, consider injecting a sinusoidal current whose frequency is near an integer multiple, m , of the oscillation frequency, so that i (t ) = I m cos [(m 0 + ⌬ )t ]
(3.24)
where ⌬ << 0 . Substituting (3.24) into (3.23) and noting that there is a negligible net contribution to the integral by terms other than when n = m , one obtains the following approximation:
(t ) ≈
I m c m sin (⌬ t ) 2q max ⌬
(3.25)
The spectrum of (t ) therefore consists of two equal sidebands at ± ⌬ , even though the injection occurs near some integer multiple of 0 . This observation is fundamental to understanding the evolution of noise in an oscillator. Unfortunately, we are not quite done: (3.25) allows us to figure out the spectrum of (t ), but we ultimately want to find the spectrum of the output voltage of the oscillator, which is not quite the same thing. The two quantities are linked through the actual output waveform, however. To illustrate what we mean by this linkage, consider a specific case where the
74
RF and Microwave Oscillator Design
output may be approximated as a sinusoid, so that v out (t ) = cos [ 0 t + (t )]. This equation may be considered a phase-to-voltage converter; it takes phase as an input, and produces from it the output voltage. This conversion is fundamentally nonlinear because it involves the phase modulation of a sinusoid. Performing this phase-to-voltage conversion, and assuming ‘‘small’’ amplitude disturbances, we find that the single-tone injection leading to (3.25) results in two equal-power sidebands symmetrically disposed about the carrier:
冉
Im c m P SBC (⌬ ) = 10 log 4q max ⌬
冊
2
(3.26)
To distinguish this result from nonlinear mixing phenomena, note that the amplitude dependence is linear (the squaring operation simply reflects the fact that we are dealing with a power quantity here). This relationship can be, and has been, verified experimentally for an exceptionally wide range of practical oscillators. The foregoing result may be extended to the general case of a white noise source [8]:
P SBC (⌬ ) ≈ 10 log
冢
i n2 ⌬f
∞
∑ c 2m
m=0
(4q max ⌬ )2
冣
(3.27)
Equations (3.26) and (3.27) imply both upward and downward frequency translations of noise into the noise near the carrier, as illustrated in Figure 3.9. Figure 3.9 summarizes what the foregoing equations tell us: Components of noise near integer multiples of the carrier frequency all fold into noise near the carrier itself. Noise near dc gets upconverted, with relative weight given by coefficient c 0 , so 1/f device noise ultimately becomes 1/f 3 noise near the carrier; noise near the carrier stays there, weighted by c 1 ; and white noise near higher integer multiples of the carrier undergoes downconversion, turning into noise in the 1/f 2 region. Note that the 1/f 2 shape results from the integration implied by the step change in phase caused by an impulsive noise input. Since an integration (even a time-varying one) gives a white voltage or current spectrum a 1/f character, the power spectral density will have a 1/f 2 shape.
Linearity, Time Variation, and Oscillator Phase Noise
75
Figure 3.9 Evolution of circuit noise into phase noise.
It is clear from Figure 3.9 that minimizing the various coefficients c n (by minimizing the ISF) will minimize the phase noise. To underscore this point quantitatively, we may use Parseval’s theorem to write: 2
冕|
∞
1 ∑ c 2m = m=0 so that the spectrum in the 1/f
⌫(x ) | dx = 2⌫2rms 2
(3.28)
0 2
region may be expressed as:
L {⌬ } = 10 log
冢
i n2 2 ⌫ ⌬ f rms (2q max ⌬ )2
冣
(3.29)
where ⌫rms is the rms value of the ISF. All other factors held equal, reducing ⌫rms will reduce the phase noise at all frequencies. Equation (3.29) is the rigorous equation for the 1/f 2 region and is one key result of this phasenoise model. Note that no empirical curve-fitting parameters are present in (3.29).
76
RF and Microwave Oscillator Design
Among other attributes, (3.29) allows us to study quantitatively the upconversion of 1/f noise into close-in phase noise. Noise near the carrier is particularly important in communication systems with narrow channel spacings. In fact, the allowable channel spacings are frequently constrained by the achievable phase noise. Unfortunately, it is not possible to predict close-in phase noise correctly with LTI models. This problem disappears if the new model is used. Specifically, assume that the current noise behaves as follows in the 1/f region:
1/f ⌬
i n2, 1/f = i n2
(3.30)
where 1/f is the 1/f corner frequency. Using (3.27) we obtain the following for the noise in the 1/f 3 region
L {⌬ } = 10 log
The 1/f
3
冢
i n2 2 c ⌬f 0
1/f (8q 2max ⌬ 2 ) ⌬
冣
(3.31)
corner frequency is then ⌬ 1/f 3 = 1/f
c 20 4⌫2rms
= 1/f
⌫2dc ⌫2rms
(3.32)
from which we see that the 1/f 3 phase noise corner is not necessarily the same as the 1/f device/circuit noise corner; it will generally be lower. In fact, since ⌫dc is the dc value of the ISF, there is a possibility of reducing by large factors the 1/f 3 phase noise corner. The ISF is a function of the waveform, and hence potentially under the control of the designer, usually through adjustment of the rise and fall time symmetry. This result is not anticipated by LTI approaches and is one of the most powerful insights conferred by this LTV model. This result has particular significance for technologies with notoriously poor 1/f noise performance, such as CMOS and GaAs MESFETs. A specific circuit example of how one may exploit this observation follows shortly. One more extremely powerful insight concerns the influence of cyclostationary noise sources. As alluded to earlier, the noise sources in many oscillators cannot be well modeled as stationary. A typical example is the
Linearity, Time Variation, and Oscillator Phase Noise
77
nominally white drain or collector noise current in a MOSFET. Noise currents are a function of bias currents, and the latter vary periodically and significantly with the oscillating waveform. The LTV model is able to accommodate a cyclostationary white noise source with ease, since such a source may be treated as the product of a stationary white noise source and a periodic function [9]: i n (t ) = i n0 (t ) ␣ ( 0 t )
(3.33)
Here, i n0 is a stationary white noise source whose peak value is equal to that of the cyclostationary source, and ␣ (x ) is a periodic unitless function with a peak value of unity. Substituting this into (3.21) allows us to treat cyclostationary noise as a stationary noise source provided we define an effective ISF as follows: ⌫eff (x ) = ⌫(x ) ␣ (x )
(3.34)
Cyclostationarity is thus easily accommodated within the framework already established. None of the foregoing conclusions changes as long as ⌫eff is used in all of the equations. Having identified the factors that influence oscillator noise, we are now in a position to articulate the requirements that must be satisfied to make a good oscillator. First, in common with the revelations of LTI models, both the signal power and resonator Q should be maximized, all other factors held constant. In addition, note that an active device is always necessary to compensate for tank loss, and that active devices always contribute noise. Note also that the ISFs tell us that there are sensitive and insensitive moments in an oscillation cycle. Of the infinitely many ways that an active element could return energy to the tank, this energy should be delivered all at once, where the ISF has its minimum value. In an ideal LC oscillator, therefore, the transistor would remain off almost all of the time, waking up periodically to deliver an impulse of current at the signal peak(s) of each cycle. The extent to which real oscillators approximate this behavior determines in large part the quality of their phase noise properties. Since an LTI theory treats all instants as equally important, such theories are unable to anticipate this important result. The prescription for impulsive energy restoration has actually been practiced for centuries, but in a different domain. In mechanical clocks, a structure known as an escapement regulates the transfer of energy from a spring to a pendulum. The escapement forces this transfer to occur impulsively, and
78
RF and Microwave Oscillator Design
only at precisely timed moments that are chosen to minimize the disturbance of the oscillation period. Although this historically important analog is hundreds of years old, having been designed by intuition and trial and error, it was not analyzed mathematically until 1826, by Astronomer Royal George Airy [10]. Finally, the best oscillators will possess the symmetry properties that lead to small ⌫dc for minimum upconversion of 1/f noise. After examining some additional features of close-in phase noise, we consider in Section 3.4.1 several circuit examples of how to accomplish these ends in practice. 3.4.1 Close-In Phase Noise From the development so far, one expects the spectrum S ( ) to have a close-in behavior that is proportional to the inverse cube of frequency. That is, the spectral density grows without bound as the carrier frequency is approached. However, most measurements fail to show this behavior, and this failure is often misinterpreted, either as being the result of some new phenomenon, or as evidence of a flaw in the LTV theory. It is therefore worthwhile to spend some time considering this issue in detail. The LTV theory asserts only that S ( ) grows without bound. Most ‘‘phase’’ noise measurements actually measure the total output spectrum of the oscillator voltage. That is, what is often measured is actually S V ( ). In such a case, the output spectrum will not show a boundless growth as the offset frequency approaches zero, reflecting the simple fact that a cosine function is bounded, even for unbounded arguments. This bound causes the measured spectrum to flatten as the carrier is approached, with a resulting shape that is Lorentzian [11, 12] (see Figure 3.10).
Figure 3.10 Lorentzian spectrum.
Linearity, Time Variation, and Oscillator Phase Noise
79
Depending on the details of how the measurement is performed, the −3-dB corner may or may not be observed. If a spectrum analyzer is used, the corner will typically be observed. If an ideal phase detector and a phaselocked loop were available to downconvert the spectrum of (t ) and measure it directly, no flattening would be observed at all. If a real phase detector, possessing limited range, is used in such a measurement, a −3-dB corner will generally be observed, but the precise value of the corner will now be a function of the instrumentation; the measurement will no longer reflect the inherent spectral properties of the oscillator. The lack of consistency in measurement techniques has been a source of great confusion in the past.
3.5 Circuit Examples 3.5.1 LC Oscillators Having derived expressions for phase noise at low and moderate offset frequencies, it is instructive to apply to practical oscillators the insights gained. We examine first the popular Colpitts oscillator and its relevant waveforms (see Figures 3.11 and 3.12). An important feature is that the drain current flows only during a short interval coincident with the most benign moments (the peaks of the tank voltage). Its corresponding excellent phase noise properties account for the popularity of this configuration. It has long been known that the best phase noise occurs for a certain narrow range of tapping ratios (e.g., a 4:1 capacitance ratio), but before the LTV theory, no theoretical basis existed to explain a particular optimum.
Figure 3.11 Colpitts oscillator (simplified).
80
RF and Microwave Oscillator Design
Figure 3.12 Approximate incremental tank voltage and drain current for the Colpitts oscillator.
Both LTI and LTV models point out the value of maximizing signal amplitude. To evade supply voltage or breakdown constraints, one may employ a tapped resonator to decouple resonator swings from device voltage limitations. A common configuration that does so is Clapp’s modification to the Colpitts oscillator (Figure 3.13). Differential implementations of oscillators with tapped resonators have recently made an appearance in the literature [13–15]. These types of oscillators become increasingly attractive as supply voltages scale downward, where conventional resonator connections lead to VDD -constrained signal swings. The use of tapping allows signal energy to remain high even with low supply voltages.
Figure 3.13 Clapp oscillator.
Linearity, Time Variation, and Oscillator Phase Noise
81
Phase-noise predictions using the LTV model are frequently more accurate for bipolar oscillators due to the availability of better device noise models. In [15] impulse response modeling (see Appendix 3A) is used to determine the ISFs for the various noise sources within the oscillator, and this knowledge is used to optimize the noise performance of a differential bipolar VCO. A simplified schematic of this oscillator is shown in Figure 3.14(a). A tapped resonator is used to increase the tank signal power, P sig . The optimum capacitive tapping ratio is calculated to be around 4.5 (corresponding to a capacitance ratio of 3.5) based on simulations that take into account the cyclostationarity of the noise sources. Specifically, the simulation accounts for noise contributions by the base spreading resistance and collector shot noise of each transistor, as well as the resistive losses of the tank elements. The ISFs (taken from [15], in which these are computed through direct evaluation in the time domain, as described in Appendix 3A) for the shot noise of the core oscillator transistors, and for the bias source, are shown in Figure 3.14(b) and 3.14(c), respectively. As can be seen, the tail current noise has an ISF with double the periodicity of the oscillation frequency, owing to the differential topology of the circuit. Noteworthy is the observation that tail noise only at even multiples of the oscillation frequency thus contribute to phase noise. The individual ISFs are used to compute the contribution of each corresponding noise sources, and the contributions summed. The reduction of 1/f noise upconversion in this topology is clearly seen in Figure 3.15, which shows a predicted and measured 1/f 3 corner of 3 kHz, in comparison with an individual device 1/f noise corner of 200 kHz. Note that the then-current version of one commercial simulation tool, Spectre, fails in this case to identify a 1/f 3 corner within the offset frequency range shown, resulting in a 15-dB underestimate at a 100-Hz offset. The measured phase noise in the 1/f 2 region is also in excellent agreement with the LTV model’s predictions. For example, the predicted value of −106.2 dBc/Hz at 100-kHz offset is negligibly different from the measured value of −106 dBc/Hz. As a final comment, this particular VCO design is also noteworthy for its use of a separate automatic amplitude control loop, which allows for independent optimization of the steady-state and start-up conditions in terms of phase noise. As mentioned, a key insight of the LTV theory concerns the importance of symmetry, the effects of which are partially evident in the preceding example. A configuration that exploits this knowledge more fully is the symmetrical negative resistance oscillator shown in Figure 3.16 [8]. This configuration is not new by any means, but an appreciation of its symmetry properties is. Here, it is the half-circuit symmetry that is important, because
82
RF and Microwave Oscillator Design
Figure 3.14 (a) Simplified schematic of the VCO in [15], (b) the ISF for the shot noise of each core transistor, and (c) the ISF for the shot noise of the tail current.
Linearity, Time Variation, and Oscillator Phase Noise
83
Figure 3.15 Measured and predicted phase noise of VCO in [15].
Figure 3.16 Simple symmetrical negative resistance oscillator.
noise in the two half circuits is only partially correlated at best. By selecting the relative widths of the PMOS and NMOS devices appropriately to minimize the dc value of the ISF (⌫dc ) for each half -circuit, one may minimize the upconversion of 1/f noise. Through exploitation of symmetry in this manner, the 1/f 3 corner can be dropped to exceptionally low values, even though device 1/f noise corners may be high (as is typically the case for
84
RF and Microwave Oscillator Design
CMOS). Furthermore, the bridge-like arrangement of the transistor quad allows for greater signal swings, compounding the improvements in phase noise. As a result of all of these factors, a phase noise of −121 dBc/Hz at an offset of 600 kHz at 1.8 GHz has been obtained with low-Q (estimated to be 3 to 4) on-chip spiral inductors, on 6 mW of power consumption in a 0.25- m CMOS technology [8]. This result rivals what one may achieve with bipolar technologies, as seen by comparison with the previous example. With a modest increase in power, the same oscillator’s phase noise becomes compliant with specifications for GSM1800. 3.5.2 Ring Oscillators As an example of a circuit that does not well approximate ideal behavior, consider a ring oscillator. First, the ‘‘resonator’’ Q is poor since the energy stored in the node capacitances is reset (discharged) every cycle. Hence, if the resonator of a Colpitts oscillator may be likened to a fine crystal wine glass, the resonator of a ring oscillator is mud. Next, energy is restored to the resonator during the edges (the worst possible times), rather than at the voltage maxima. These factors account for the well-known terrible phase noise performance of ring oscillators. As a consequence, ring oscillators are found only in the most noncritical applications, or inside wideband PLLs that clean up the spectrum. However, there are certain aspects of ring oscillators that can be exploited to achieve better phase noise performance in a mixed-mode integrated circuit. Noise sources on different nodes of an oscillator may be strongly correlated due to various reasons. Two examples of sources with strong correlation are substrate and supply noise, arising from current switching in other parts of the chip. The fluctuations on the supply and substrate will induce a similar perturbation on different stages of the ring oscillator. To understand the effect of this correlation, consider the special case of having identical noise sources on all the nodes of the ring oscillator as shown in Figure 3.17. If all the inverters in the oscillator are the same, the ISF for different nodes will differ only in phase by multiples of 2 /N, as shown in Figure 3.18. Therefore, the total phase due to all the sources is given by (3.21) through superposition [16]: t
(t ) =
1 q max
冕 冤∑ 冉 N−1
⌫ 0 +
i ( )
−∞
n=0
2 n N
冊冥
d
(3.35)
Linearity, Time Variation, and Oscillator Phase Noise
85
Figure 3.17 Five-stage ring oscillator with identical noise sources on all nodes.
Figure 3.18 Phasors for noise contributions from each source.
Expanding the term in brackets in a Fourier series, it can be observed that it is zero except at dc and multiples of N 0 —that is,
(t ) =
N q max
∞
∑ c nN
n=0
t
冕
i ( ) cos (nN 0 ) d
(3.36)
−∞
which means that for fully correlated sources, only noise in the vicinity of integer multiples of N 0 affects the phase. Therefore, every effort should be made to maximize the correlations of noise arising from substrate and supply perturbations. This result can be achieved by making the inverter stages and the noise sources on each node as similar to each other as possible by proper layout and circuit design. For example, the layout should be kept symmetrical, and the inverter stages should be laid out close to each other
86
RF and Microwave Oscillator Design
so that substrate noise appears as a common-mode source. This latter consideration is particularly important in the case of a lightly doped substrate, since such a substrate may not act as a single node [17]. It is also important that the orientation of all the stages be kept identical. The interconnecting wires between the stages must be identical in length and shape, and a common supply line should feed all the inverter stages. Furthermore, the loading on all stages should be kept identical, perhaps by using dummy buffer stages as necessary, for example. Use of the largest number of stages consistent with oscillation at the desired frequency will also be helpful because, as a practical matter, fewer c n coefficients will then affect the phase noise. Finally, as the low frequency portion of the substrate and supply noise then dominates, one should exploit symmetry to minimize ⌫dc . Another common conundrum concerns the preferred topology for MOS ring oscillators (i.e., whether a single-ended or differential topology results in better jitter and phase-noise performance for a given center frequency, f 0 , and total power dissipation, P ). Facilitating an analysis of these choices is an approximate expression for the ISF (see Figure 3.19). The ISF is approximated by two triangles, as shown in Figure 3.19. The rms value of the ISF has a value given by ⌫2rms
1 = 3
冉 冊
3
1 (1 + A 3 ) f ri′se
(3.37)
Figure 3.19 Derivation of approximate analytical expression for ring oscillator ISF.
Linearity, Time Variation, and Oscillator Phase Noise
87
where f ri′se and f fa′ll are the maximum slope during the rising and falling edges, and A is the ratio of f ri′se to f fa′ll [6]. Coupling the ISF equation with the noise equations for transistors, one may derive expressions for the phase noise of MOS differential and single-ended oscillators [16]. Based on these expressions the phase noise of a single-ended (inverter chain) ring oscillator is found to be independent of the number of stages for a given power dissipation and frequency of operation. However, for a differential ring oscillator, the phase noise (jitter) grows with the number of stages. Therefore, even a properly designed differential CMOS ring oscillator underperforms its single-ended counterpart, with a disparity that increases with the number of stages. The difference in the behavior of these two types of oscillators with respect to the number of stages can be traced to the way they dissipate power. The dc current drawn from the supply is independent of the number and slope of the transitions in differential ring oscillators. In contrast, inverter-chain ring oscillators dissipate power mainly on a per transition basis and therefore have better phase noise for a given power dissipation. However, a differential topology may still be preferred in ICs with a large amount of digital circuitry because of the lower sensitivity to substrate and supply noise, as well as lower noise injection into other circuits on the same chip. The decision of which architecture to use should be based on both of these considerations. Yet another commonly debated question concerns the optimum number of inverter stages in a ring oscillator to achieve the best jitter and phase noise for a given f 0 and P. For single-ended CMOS ring oscillators, the phase noise and jitter in the 1/f 2 region are not strong functions of the number of stages [16]. However, if the symmetry criteria are not well satisfied, and/or the process has large 1/f noise, a larger N will reduce the jitter. This reduction results from the faster edge speeds that must accompany the use of a larger number of stages to achieve the same oscillation frequency. The faster edge speeds reduce the effect of asymmetries in rise and fall times, and thus reduce the upconversion of 1/f noise. In general, the choice of the number of stages must be made on the basis of several design criteria, such as 1/f noise effect and the desired maximum frequency of oscillation, as well as the influence of external noise sources, such as supply and substrate noise, that may not scale with N. A symmetry-based reduction in 1/f noise can significantly augment the reduction that may be provided by the trapresetting that can attend operation of MOSFETs in the switching regime [18, 19]. The jitter and phase-noise behavior is different for differential ring oscillators. Jitter and phase noise increase with an increasing number of
88
RF and Microwave Oscillator Design
stages. Hence, if the 1/f noise corner is not large, and/or proper symmetry measures have been taken, the minimum number of stages (3 or 4) should be used to give the best performance. This recommendation holds even if the power dissipation is not a primary issue. It is not fair to argue that burning more power in a larger number of stages allows the achievement of better phase noise, since dissipating the same total power in a smaller number of stages with larger devices results in better jitter and phase noise, as long as it is possible to maximize the total charge swing.
3.6 Amplitude Response While the close-in sidebands are dominated by phase noise, the far-out sidebands are greatly affected by amplitude noise. Unlike the induced excess phase, the excess amplitude, A (t ), due to a current impulse decays with time. This decay is the direct result of the amplitude restoring mechanisms always present in practical oscillators. The excess amplitude may decay very slowly (e.g., in a harmonic oscillator with a high-quality resonant circuit) or very quickly (e.g., a ring oscillator). Some circuits may even demonstrate an underdamped second-order amplitude response. The detailed dynamics of the amplitude control mechanism have a direct effect on the shape of the noise spectrum. In the context of the ideal LC oscillator of Figure 3.4, a current impulse with an area, ⌬q , will induce an instantaneous change in the capacitor voltage which, in turn, will result in a change in the oscillator amplitude that depends on the instant of injection, as shown in Figure 3.5. The amplitude change is proportional to the instantaneous normalized voltage change, ⌬V /Vmax , for small injected charge ⌬q << q max —that is, ⌬A = ⌳( 0 t )
⌬V ⌬q = ⌳( 0 t ) V max q max
(3.38)
where ⌳( 0 t ) is a periodic function that determines the sensitivity of each point on the waveform to an impulse and is called the amplitude impulse sensitivity function. It is the amplitude counterpart of the phase impulse sensitivity function, ⌫( 0 t ). From a development similar to that of Section 3.3, the amplitude impulse response can be written as h A (t , ) =
⌳( 0 t ) d (t − ) q max
(3.39)
Linearity, Time Variation, and Oscillator Phase Noise
89
where d (t − ) is a function that defines how the excess amplitude decays. Figure 3.20 shows two hypothetical examples of d (t ) for a low-Q oscillator with overdamped response, and a high-Q oscillator with underdamped amplitude response. For most oscillators, the amplitude-limiting system can be approximated as first- or second-order [20], again for small disturbances. The function d (t − ) typically will thus be either a dying exponential or a damped sinusoid. For a first-order system, d (t − ) = e − 0 (t − )/Q u (t − )
(3.40)
Therefore, the excess amplitude response to an arbitrary input current, i (t ), is given by the superposition integral, t
A (t ) =
冕
−∞
i ( ) ⌳( 0 ) e − 0 (t − )/Q d q max
(3.41)
If i (t ) is a white noise source with power spectral density i n2 , the output power spectrum of the amplitude noise, A (t ), can be shown to be L amplitude {⌬ } =
⌳2rms q 2rms
冉
i n2 /⌬f
20 2 + ⌬ 2 Q2
冊
(3.42)
where ⌳rms is the rms value of ⌳( 0 t ). If L total is measured, the sum of both L amplitude and L phase will be observed and hence there will be a pedestal in the phase noise spectrum at 0 /Q as shown in Figure 3.21. Also note
Figure 3.20 Overdamped and underdamped amplitude responses.
90
RF and Microwave Oscillator Design
Figure 3.21 Phase, amplitude, and total sideband powers for the overdamped amplitude response.
that the significance of the amplitude response depends greatly on ⌳ rms which, in turn, depends on the topology. As a final comment on the effect of amplitude-control dynamics, an underdamped response would result in a spectrum very similar to Figure 3.21, except for the presence of peaking in the vicinity of 0 /Q .
3.7 Summary The insights gained from LTI phase noise models are simple and intuitively satisfying: One should maximize signal amplitude and resonator Q . An additional, implicit insight is that the phase shifts around the loop generally must be arranged so that oscillation occurs at or very near the center frequency of the resonator. This way, there is a maximum attenuation by the resonator of off-center spectral components. Deeper insights provided by the LTV model are that the resonator energy should be restored impulsively at the ISF minimum, instead of evenly throughout a cycle, and that the dc value of the effective ISF should be made as close to zero as possible to suppress the upconversion of 1/f noise into close-in phase noise. The theory also shows that the inferior broadband noise performance of ring oscillators may be offset by their potentially superior ability to reject common-mode substrate and supply noise.
References [1]
Lee, T. H., The Design of CMOS Radio-Frequency Integrated Circuits, New York: Cambridge University Press, 1998.
Linearity, Time Variation, and Oscillator Phase Noise
91
[2]
Ham, D., and A. Hajimiri, ‘‘Concepts and Methods in Optimization of Integrated LC VCOs,’’ IEEE J. Solid-State Circuits, June 2001.
[3]
Leeson, D. B., ‘‘A Simple Model of Feedback Oscillator Noise Spectrum,’’ Proc. IEEE, Vol. 54, February 1966, pp. 329–330.
[4]
Razavi, B., ‘‘A Study of Phase Noise in CMOS Oscillators,’’ IEEE Journal of SolidState Circuits, Vol. 31, No. 3, March 1996.
[5]
Hajimiri, A., and T. Lee, ‘‘A General Theory of Phase Noise in Electrical Oscillators,’’ IEEE Journal of Solid-State Circuits, Vol. 33, No. 2, February 1998, pp. 179–194.
[6]
Hajimiri, A., and T. Lee, The Design of Low-Noise Oscillators, Boston, MA: Kluwer, 1999.
[7]
Kaertner, F. X., ‘‘Determination of the Correlation Spectrum of Oscillators with Low Noise,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 37, No. 1, January 1989.
[8]
Hajimiri, A., and T. Lee, ‘‘Design Issues in CMOS Differential LC Oscillators,’’ IEEE Journal of Solid-State Circuits, May 1999.
[9]
Gardner, W. A., Introduction to Random Processes, New York: McGraw-Hill, 1990.
[10]
Airy, G. B., ‘‘On the Disturbances of Pendulums and Balances, and on the Theory of Escapements,’’ Trans. of the Cambridge Philosophical Society, Vol. III, Part I, 1830, pp. 105–128.
[11]
Edson, W. A., ‘‘Noise in Oscillators,’’ Proc. IRE, August 1960, pp. 1454–1466.
[12]
Mullen, J. A., ‘‘Background Noise in Nonlinear Oscillators,’’ Proc. IRE, August 1960, pp. 1467–1473.
[13]
Craninckx, J., and M. Steyaert, ‘‘A 1.8GHz CMOS Low-Phase-Noise Voltage-Controlled Oscillator with Prescaler,’’ IEEE Journal of Solid-State Circuits, Vol. 30, No. 12, December 1995, pp. 1474–1482.
[14]
Ahrens, T. I., and T. H. Lee, ‘‘A 1.4-GHz, 3-mW CMOS LC Low Phase Noise VCO Using Tapped Bond Wire Inductance,’’ Proc. ISLPED, August 1998, p. 16-9.
[15]
Margarit, M. A., et al., ‘‘A Low-Noise, Low-Power VCO with Automatic Amplitude Control for Wireless Applications,’’ IEEE Journal of Solid-State Circuits, Vol. 34, No. 6, June 1999, pp. 761–771.
[16]
Hajimiri, A., S. Limotyrakis, and T. H. Lee, ‘‘Jitter and Phase Noise in Ring Oscillators,’’ IEEE Journal of Solid-State Circuits, Vol. 34, No. 6, June 1999, pp. 790–804.
[17]
Blalack, T., et al., ‘‘Experimental Results and Modeling of Noise Coupling in a Lightly doped Substrate,’’ Tech. Dig. IEDM, December 1996.
[18]
Bloom, I., and Y. Nemirovsky, ‘‘1/f Noise Reduction of Metal-Oxide-Semiconductor Transistors by Cycling from Inversion to Accumulation,’’ Appl. Phys. Lett., Vol. 58, April 1991, pp. 1664–1666.
[19]
Gierkink, S. L. J., et al., ‘‘Reduction of the 1/f Noise Induced Phase Noise in a CMOS Ring Oscillator by Increasing the Amplitude of Oscillation,’’ Proc. 1998 Int. Symp. Circuits and Systems, Vol. 1, May 31–June 3, 1998, pp. 185–188.
[20]
Clarke, K. K., and D. T. Hess, Communication Circuits: Analysis and Design, Reading, MA: Addison-Wesley, 1971.
92
RF and Microwave Oscillator Design
Appendix 3A: Notes on Simulation Exact analytical derivations of the ISF are usually not obtainable for any but the simplest oscillators. Various approximate methods are outlined in [5, 6], but the most generally accurate method is direct evaluation of the timevarying impulse response. In this direct method, an impulsive excitation perturbs the oscillator, and the steady-state phase perturbation is measured. The timing of the impulse with respect to the unperturbed oscillator’s zero crossing is then incremented and the simulation repeated until the impulse has been ‘‘walked’’ through an entire cycle. The impulse must have a small enough value to ensure that the assumption of linearity holds. Just as an amplifier’s step response cannot be evaluated properly with steps of arbitrary size, one must judiciously select the area of the impulse, rather than blindly employing some fixed value (e.g., 1 coulomb). If one is unsure if the impulse chosen is sized properly, linearity may always be tested explicitly by scaling the size of the impulse by some amount and verifying that the response scales by the same factor. Finally, some confusion persists about whether the LTV theory properly accommodates the phenomenon of amplitude-to-phase conversion that some oscillators exhibit. As long as linearity holds, the LTV theory provides the correct answer, provided that an exact ISF has been obtained. This is due to the fact that changes in the phase of oscillator arising from an amplitude change appear in the impulse response of the oscillator. As noted in the preceding paragraphs, the direct impulse response method is the most reliable one, as it makes no assumptions other than linearity. This reliability is in contrast with the approximate analytical approaches offered in the appendix to [1].
Acknowledgments The authors of Chapter 3 are grateful to Professor David Leeson of Stanford for his gracious assistance and encouragement when the LTV theory was in its formative stages.
4 High-Frequency Oscillator Circuit Design Juan Obregon, Jean-Christophe Nallatamby, Michel Prigent, Marc Camiade, and Dominique Rigaud The development of civil applications in RF, microwaves, and millimeter waves has gone through unprecedented progress in recent years. In fact, this great stride was made possible thanks to the parallel development of: • New semiconductor devices; • Associated monolithic technologies.
Together with these new technologies, computer-aided design tools have progressed, gaining the ability to handle increasingly complex circuit architecture with active and passive circuit functions combined on a single high frequency (HF) monolithic chip. Among these functions, one of the most important is undoubtedly the oscillator function. This function can either generate a pure or modulated microwave carrier for the transmitter or be used as a local oscillator in receiver systems. The characteristics requested from the oscillators depend widely on the systems in which they are inserted. However, some characteristics are common to all oscillators intended for mass production. Besides circuit manufacturing reproducibility of the predicted electrical performances, one of the primary characteristics is spectral purity and thermal stability. 93
94
RF and Microwave Oscillator Design
This chapter describes a general design method for RF and microwave oscillators. These developments are due to a large extent to the very close collaboration between the academic research laboratories IRCOM and CEM2 supported by French CNRS and industrial laboratory U.M.S. All this research work was carried out in common by these labs with the final objective of transferring new design methods to an industrial environment in which they are intensively used and constantly confronted with experience. It is only this constant feedback between theory and experiment that makes it possible to determine the validity and the industrial viability of various semiconductor models, design methods, or simulation tools. Intensive oscillator designs must be supported by a proven combination of the following: • Semiconductor device models; • Computer-based design tools; • Design rules.
Designing optimized oscillator circuits requires both reliable and stateof-the-art methods [1]. The apparent discrepancy between ‘‘well-tried,’’ yet necessarily ‘‘stateof-the-art’’ tools, can be overcome by very close cooperation between academic and industrial labs to reduce the transfer time from lab to industry. Section 4.1 discusses the device modeling of two main active devices: field-effect transistors (FETs) and bipolar transistors. To extract their electrical nonlinear model and noise sources, the measurement setup utilized for the full characterization of these microwave devices will be examined. Section 4.2 focuses on the computer-aided design (CAD) simulation tools required for the analysis of nonlinear autonomous circuits as well as the computation of their phase/amplitude noise spectra. Section 4.3 details the design rules leading to the optimization of the transistor oscillator phase noise, which is one of the prime characteristics in the design of RF and microwave communication systems. Note that failing to apply these rules may involve a degradation of the phase-noise spectrum from 10 dB to 20 dB and even more. This degradation cannot even be corrected by fine-tuning on the final testing of the packaged oscillator circuit. Section 4.4 presents some examples the application of practical oscillator circuit design to several fields, including telecommunications systems and automotive applications (collision warning or avoidance systems); these applications range from microwaves to millimeter waves.
High-Frequency Oscillator Circuit Design
95
In Appendix 4A, the models of an HBT and a PHEMT are shown. Appendix 4B details all the computation to extract noise sources from the measured ones. Finally, Appendix 4C describes an easy-to-use oscillator circuit. The objective here is for readers to be able to use this example as a framework to perform numerical computations, especially for nonlinear simulation and its associated phase-noise spectrum. This circuit can serve as a benchmark for all scientists who need to test their microwave circuit simulator to verify the accuracy of the results obtained. This circuit was subjected to careful checking and comparisons on our premises by different calculation methods. Results given in Appendix 4C can be regarded as reliable.
4.1 Transistor CAD-Oriented Circuit Models 4.1.1 Introduction The transistors are usually classified into two main families: the unipolar transistors, based on the field effect, in which only one carrier type takes part in the current, and the bipolar transistors, in which the two carrier types contribute to the current. This section aims to describe models that can be easily included into CAD environments and that don’t lead to prohibitive simulation time. These models must be able to represent experimental phenomena observed in different operating conditions. They must be able to handle the noise behavior of transistors, even driven by time-varying large signals. Physically based models are established by solving the differential equations governing the carrier flow in the semiconductor device [2, 3]. These models are well suited for a good understanding of the different physical phenomena such as trap effects and breakdown effects, but the computation time is not yet compatible with the circuit design time. Moreover, although the carrier-transport computation methods are now well established, some parameters must be still fitted to find accurate results (i.e., doping profiles and mobility). The second kind of model, called the black-box model, is based on a purely mathematical representation (e.g., neural networks and analytical or polynomial functions) of the electrical response at the transistor terminals. They can be used in CAD software but they do not accurately take into account all the internal physical phenomena such as noise behavior and nonquasi-static effects.
96
RF and Microwave Oscillator Design
The electrical models are constituted of lumped or distributed, linear or nonlinear elements. Thus, their integrations in CAD software are easy. Moreover, they allow a precise modeling of the phenomena that take place into the devices. Note that in our models all the constituting elements are extracted from experimental characterizations. Section 4.1.2 describes a bipolar transistor model [4, 5], including the fundamental effect and some secondary or parasitic effects. The great dependence of the bipolar transistor behavior on the temperature will also be addressed. Section 4.1.3 considers the FET and presents a first electrical model valid as for MESFET or HEMT. It also includes parasitic effects. At last, a HEMT nonlinear distributed model will be described. It is essential to model the low-frequency noise behavior of the transistor: Due to the longitudinal current flowing from source to drain, the low-frequency noise sources are physically distributed along the transistor channel. Therefore, an accurate model CAD-oriented for nonlinear circuits must take into account this distribution. In bipolar transistors and in heterojunction bipolar transistors (HBTs), where the current flows vertically, this distributed modeling is not needed, at least at the first order. Section 4.1.4 describes the transistor characterization setup with its two measurement capabilities: pulsed I (V ) and pulsed S-parameters. Then, Section 4.1.5 presents model extractions of bipolar transistors and FETs. Section 4.1.6 deals with the origins of noise sources in semiconductor devices, particularly low-frequency noise sources, which are the main cause of AM and PM noise near carriers in oscillators. Section 4.1.7 describes the setup for measuring these noise sources, and Section 4.1.8 details the whole nonlinear models of bipolar transistors and FETs, including low-frequency noise sources. 4.1.2 Homojunction and Heterojunction Bipolar Transistor Modeling The need to extend the homojunction bipolar transistor operating at high frequencies as well as to increase its current gain has led to the introduction of a heterojunction in the emitter base junction [6, 7]. It consists of the association of two materials with different bandgaps [8, 9]: • A high bandgap material for the emitter (e.g., AlGaAs, GaInP, and
Si); • A low bandgap material for the base (e.g., AsGa and SiGe).
High-Frequency Oscillator Circuit Design
97
The valence band discontinuity ⌬E V of the base emitter heterojunction avoids the holes injection from base to emitter, while the conduction band discontinuity ⌬E C facilitates the electrons to flow from the emitter to the base. In addition to the fundamental transistor effect, some secondary effects appear in particularly operating areas or as limitation effects. These effects must be taken into account to improve the transistor model and to make more accurate and realistic simulations. 4.1.2.1 Parasitic Elements
Two parasitic effects appear in the Gummel plot of the transistor (which represents the I C and I B currents versus VCE = VBE in logarithmic axes). An example is shown Figure 4.1 [10]. In an ideal transistor, the plots of I C and I B would be two straight lines, separated by a ratio equal to  F . In reality, two differences appear: • An I B curvature for high VBE with a voltage drop ⌬V due to the
series resistances R B and R E . ⌬V = R B I B + R E I E
(4.1)
• At very low current, the base current is higher than the emitter one;
this indicates that leakage currents exist in parallel across the base-
Figure 4.1 Bipolar transistor Gummel plot.
98
RF and Microwave Oscillator Design
emitter junction and are more important than the transistor effect. These recombination currents are modeled by two additional diodes in parallel across each junction I FE and I FC described by
冉 冉
I FC = I SFC e
I FE = I SFE e
V BC fC U T
V BE fE U T
冊 冊
−1
(4.2)
−1
(4.3)
The I SFC , I SFE currents and fE , fC ideality factors are fitting parameters. To model the device accesses, two inductances, L C and L B , are added to the model. The bounding wire can also be taken into account with these inductances. For a monolithic technology transistor, L E models the inductive effects due to the ground via hole. C PC and C PB are the pad capacitances. 4.1.2.2 Kirk Effect
In a high-level injection regime, the electron density crossing the base collector junction is not low with regard to the collector doping profile [11]. To maintain the electrical neutrality, the density of electron carriers flowing through the collector increases, leading to an expansion of the collector depletion region. When this depletion region reaches the collector boundary, the electron density increase cannot be compensated by the depletion region expansion. The collector depletion region carrier density becomes negative. This sign change induces an electrical field inversion and a hole injection from collector to base is observed. The consequence is a base effective length increase, inducing a higher transit time and then, a decrease of maximum cutoff frequency. This phenomenon can be modeled with the non-quasistatic model [12, 13]. 4.1.2.3 Breakdown Phenomenon
In a normal operating regime, the electrons crossing the base collector junction are collected by a high electrical field induced by the base collector junction reverse biasing. Beyond a critical field, the electrons reach a critical velocity, which activates an impact ionization process. This phenomenon generates a current increase up to the transistor destruction. The voltage corresponding to the critical point is called the breakdown voltage (BVCB 0 ). This effect is characterized by the multiplication factor M given by [14]:
High-Frequency Oscillator Circuit Design
M=
IC = I Cn
冉
1
V CB 1− BV CB 0
冊
n
99
(4.4)
It is very important to model this effect to describe the power amplifier behavior. In oscillators, this operating area must be avoided for low-noise operation. 4.1.2.4 HBT Nonlinear Model
Figure 4.2 shows the complete nonlinear model of HBT. The base-emitter and collector-base currents I F and I R have the classical expressions:
冉 冉
I R = I SC e I F = I SE e
V BC C UT
V BE E UT
冊 冊
−1
(4.5)
−1
(4.6)
where I SC , I SE , E , and C are fitting parameters. The capacitance nonlinear equations are derived from classical semiconductor physics relations. The base-collector junction capacitance is written as
Figure 4.2 Non-quasi-static and nonlinear model of HBT.
100
RF and Microwave Oscillator Design
C jC (VBC ) =
C jC 0
冉
V 1 − BC ⌽C
冊
m jC
(4.7)
where m jC = 1/2 for an abrupt junction, and C jC 0 , ⌽C , and m jC are the fitting parameters. The base emitter junction capacitance is written as: C jE (VBE ) =
冉
C jE 0
V 1 − BE ⌽E
冊
m jE
(4.8)
where m jE = 1/2 for an abrupt junction and C jE 0 , ⌽E , and m jE are the fitting parameters. The expressions of the diffusion capacitances are C dC (VBC ) = C BCd 0 e C dE (VBE ) = C BEc e
VBC BC U T V BE D UT
(4.9) (4.10)
where C BCd 0 , C BEc , BC , D are the fitting parameters. The transcapacitances are represented by the following phenomenological relations: C dCE (VBE ) = C BCe e
V BE BE U T
C dEC (VBC ) = C BEc 0 C BEc 1 e C BEc1VBC
(4.11) (4.12)
where C BCe , C BEc 1 , C BEc 0 , and BE are the fitting parameters. 4.1.2.5 Electrothermal Nonlinear Model
One of the main points of interests of the HBT is its property to operate with high current densities. Then, a high correlation between the temperature and the transistor characteristics is observed [15]. To model the transistor thermal behavior [16, 17], the most efficient approach is to introduce the thermal dependence through the saturation currents by means of the following equations:
High-Frequency Oscillator Circuit Design
I R = I SC 0 e I F = I SE 0 e I FC = I SFC 0 e I FE = I SFE 0 e
T SC T
T SE T
冉 冉 冉 冉
T SFC T
T SFE T
冊 冊
V BC
e C UT − 1
e
V BE E UT
−1
V BC fC U T
冊 冊
101
(4.13)
(4.14)
−1
(4.15)
e fE U T − 1
(4.16)
e
V BE
I SC 0 , I SE 0 , I SFC 0 , I SFE 0 , T SC , T SE , T SFC , T SFE , fE , and fC are fitting parameters. For some transistors, it is also necessary to introduce a thermal dependence on the direct current gain:
F = 0e
1 T
(4.17)
where  0 and  1 are parameters. Obviously, the temperature has a strong influence on base emitter diffusion capacitance. To avoid too complicated models, only the C dE capacitance and its associated C dCE transcapacitance have a thermal dependence in our model. The final expressions [18] are C dE (VBE ) = C BEd 0 e C dCE (VBE ) = C BCe 0 e
C BEd1 T C BCe1 T
e e
V BE D UT V BE BE U T
(4.18) (4.19)
The parameters C BEd 0 , C BEd 1 , C BCe 1 , and C BCe 0 are fitting coefficients. Power dissipated in a transistor is written as: P diss = VBE I B + VCE I C
(4.20)
This power heats the active areas of the transistor. Owing to the short base length, the base-emitter and base-collector junctions can be considered at the same junction temperature. The temperature difference between the
102
RF and Microwave Oscillator Design
intrinsic transistor and its external environment induces a thermal diffusion from the junction toward the heat sink. To avoid the extraction of a distributed thermal model from electrical measures, a simplified model is used. Figure 4.3 represents the whole Pi nonlinear electrothermal model. C th and R th form the thermal equivalent circuit. The coupling between the thermal circuit and the nonlinear electrical model allows one to determine the operating temperature by an iterative procedure included in the circuit simulator. Figure 4.4 depicts the HBT linear model obtained by computing the incremental values of the nonlinear elements. 4.1.3 FET Operating and Modeling A field effect unipolar transistor consists of a conductive channel between two ohmic contacts, one acting as the source and the other as the drain [19]. When the channel is biased by a drain-source voltage VDS , a current flows in the channel. Neglecting the displacement current, the total current is written as: I = qn (x ) v (x ) A (x ) where
Figure 4.3 Pi electrothermal model of bipolar transistor.
(4.21)
High-Frequency Oscillator Circuit Design
103
Figure 4.4 Pi linear model of bipolar transistor.
q n (x ) v (x ) A (x ) x
is is is is is
the the the the the
electron charge. carrier density. carrier’s velocity. channel cross-sectional area. abscissa between drain and source.
A voltage applied perpendicularly by means of a third electrode, the gate, modulates the channel cross-sectional area or the carrier density, described as follows. • The modulation of the cross-sectional area leads to junction-like
transistors—principally metal semiconductor FETs (MESFETs). • The modulation of carrier density leads to MESFET-like transistors: metal oxide semiconductor FETs (MOSFETs) and high-electron mobility transistors (HEMTs). At microwaves and millimeter waves, MESFETs and HEMTs are the most used transistors. Both can be modeled by the electrical circuit presented in the following sections. A typical transistor output characteristic, I DS − V DS , at constant VGS is plotted in Figure 4.5. In Figure 4.5, two regions appear: The first is the linear region at low VDS , where the I DS current is proportional to VDS voltage. When the VDS voltage increases, the carrier velocity saturates. That
104
RF and Microwave Oscillator Design
Figure 4.5 FET output characteristic.
is, the depletion region expands toward the drain and limits the I DS current. This is the saturation region. 4.1.3.1 HEMT
As for the bipolar transistor, the contribution of a heterojunction allows for an increase in the high-frequency operation of the transistor, called the HEMT in this case. The aim of this structure is to separate the free electrons of the channel from the semiconductor supplier layer, which contains the ionized donor atoms. At the heterointerface, the conduction bands generate a potential well, with a sheet carrier of high concentration: A two-dimension electron gas is formed in GaAs. As a result, the current flows in an undoped semiconductor layer with a high carrier mobility [20]. In addition, an undoped AlGaAs thin layer, called the spacer, is inserted between the AlGaAs and GaAs layers. It allows for the isolation of impurities. The electron gas density is controlled by means of a Schottky junction (the gate) built on the n -doped AlGaAs layer. When a negative voltage VGS is applied, a decrease of carrier density in the potential well is induced: The I DS current decreases. When VGS increases, then a high electron number
High-Frequency Oscillator Circuit Design
105
coming from AlGaAs donor atoms diffuse in the channel and the I DS current increases. To obtain greater gain and higher-frequency performances, GaAs is replaced by InGaAs in the heterojunction structure. This semiconductor has a lower bandgap and a higher electronic mobility than GaAs. This transistor type is called the pseudomorphic HEMT (PHEMT), but its operation is the same as that of HEMT. The following section deals with the classical FET model, the Pi model. A Pi Model of FET
This model is usually comprised of lumped elements to represent, on one hand, the nonlinear intrinsic model and, on the other hand, the external parasitics. A physical analysis of the transistor leads to a first nonlinear model (Figure 4.6). The classical model topology is shown Figure 4.7. Extrinsic Elements
The R S and R D resistances correspond to ohmic contacts and the inactive conductive region of the channel. The R G resistance models the ohmic losses due to the electrode gate metallization and the distributed contact resistance at the metal-semiconductor interface. The L G and L D inductances model the accesses to device electrodes. The inductive behavior of bounding wire can be also taken into account with these inductances. For a monolithic technology transistor, L S models
Figure 4.6 Physical origin of FET Pi nonlinear equivalent circuits.
106
RF and Microwave Oscillator Design
Figure 4.7 Pi FET model with all parasitics.
the inductive effects due to the ground via hole. C pg and C pd are the pad capacitances. Intrinsic Elements Convective nonlinearities. The current source I DS controlled by VDS and VGS voltages represents the fundamental effect of the transistor: the field effect. To model it, we use an analytical expression derived from that originated by Tajima [21]:
if V GSN > 0.0, then I DST a = I DSS × f g × f d else I DST a = 0.0 with VGS (t − ) − V VP
VGSN = 1 +
VDSN = VDSP
VDS V (t − ) 1 + w ⭈ GS VP
冉
冊
(4.22)
High-Frequency Oscillator Circuit Design
107
VP = VP 0 + p ⭈ VDS + V fg =
冉
冊
1 1 VGSN − (1 − e −mVGSN ) m 1 1 − (1 − e −m ) m 2
f d = (1 − e −VDSN (1 + a ⭈ VDSN + b ⭈ VDSN ) )
represents the transit time of the carriers in the channel. The nine fitting parameters are I DSS , V , V P 0 , p , VDSP , w , m , a , and b . To take into account the decrease of the transconductance in HEMTs for low VGS [22], a coefficient correct_ gm is introduced: correct_ gm = 1 +  gm × (VDS − Vdm ) × (1 + tanh (␣ gm (VGS (t − ) − Vgm )))
(4.23)
I DS = I DS Ta × correct_ gm While the Vgm parameter fixes the transconductance decrease with VGS , the ␣ gm coefficient is used to fit the G m slope and  gm its magnitude. The parameter Vdm allows one to fit the transistor output conductance G D . Two nonlinear current sources, I GS and I GD , model the distributed Schottky gate junction, with the classical expressions:
冉 冉
V GD
冊 冊
I GD = I GDS e gd U T − 1 V GS
I GS = I GSS e gs U T − 1
(4.24)
(4.25)
where I GDS , gd , I GSS , and gs are fitting parameters. Linear Elements
The linear R i and R gd resistances allow us to take into account some distributed effects of the channel. Strictly speaking, these resistances are nonlinear. Nevertheless, they are usually modeled as linear resistances. Their accurate extractions are extremely difficult. C ds essentially models the electrostatic coupling between the highly doped regions under the drain and source electrodes.
108
RF and Microwave Oscillator Design
Nonlinear Capacitances
The nonlinear capacitances C GD and C GS represent the stored charge variation under the gate electrode. In fact, this charge is distributed and theoretically cannot be modeled by two independent capacitances. Nevertheless, the modeling of the charge under the gate by two capacitances can be successfully used if the fitting functions are carefully chosen. This representation gives accurate results in all the applications without any major drawbacks. The phenomenological expressions have the same form for both capacitances, with six fitting parameters:
C GS (VGS ) = Cg 0s
冉
V 1 − eff V bs
冊冉 n
冊
1 1 (V − V ts ) − (V − V bs ) + C bs 2d 1 GS 2d 2 GS (4.26)
where d , V bs , V ts , C bs , Cg 0s , and n are fitting parameters with Veff =
C GD (VGD ) = Cg 0d
1 V + V bs (d 1 − d 2 ) + ts 2 2
d1 =
√(VGS − Vts )
2
+ d2
d2 =
√(VGS − Vbs )
+ d2
冉
V′ 1 − eff V bd
+ C bd
冊冉 n′
2
冊
1 1 (VGD − V td ) − (VGD − V bd ) 2d 1′ 2d 2′ (4.27)
with V ef′f =
V + V bd 1 (d 1′ − d 2′ ) + td 2 2
d 1′ =
√(VGD − Vtd )
2
+ d ′2
d 2′ =
√(VGD − Vbd )
+ d ′2
2
where d ′, V bd , V td , C bd , Cg 0d , and n ′ are fitting parameters.
High-Frequency Oscillator Circuit Design
109
4.1.3.2 Other Phenomena in GaAs FETs
As for the bipolar transistor, some secondary effects exist in FETs and limit their operating range. Breakdown Effects
The FET power operating range is essentially restricted, on one hand, by the gate conduction current, and, on the other hand, by the breakdown voltage [22, 23]. Two breakdown types arise in FETs: • The impact ionization breakdown occurs for a high V ds voltage and
a VGS voltage near the channel pinch-off. The electrons flowing in the channel are accelerated by the field and generate hole-electron pairs by striking crystal atoms. The holes are collected by the gate and the electrons by the drain. This phenomenon is modeled by a nonlinear current source between the gate and the drain, based on a phenomenological equation extracted from measures: 4
3
2
I BDG = I dg × e AG × V GS + BG × V GS + CG × V GS + DG × V GS + EG × V DS (4.28) where I dg , AG, BG, CG, DG, and EG are fitting parameters. • The breakdown, due to the Kink effect, occurs for a VGS voltage higher than the pinch-off voltage. This phenomenon is due to the presence of surface traps in the semiconductor and induces an increase of the drain current. A nonlinear voltage-controlled current source is then added in parallel with the fundamental I DS source to model this phenomenon. A phenomenological expression is extracted from measures 4
3
2
I BDS = I DSS × e AS × V GS + BS × V GS + CS × V GS + DS × V GS + ES × V DS (4.29) where AS, BS, CS, DS, and ES are fitting parameters. Trapping Effects
The trapping effects in semiconductors are due to crystal impurities and defects. They generate intermediate energy states in the forbidden energy band, which can be occupied by the carriers. The carrier capture and emission times by the traps vary between 1 nanosecond and few seconds. These traps
110
RF and Microwave Oscillator Design
generate transient currents with time constant not negligible [24]. Three main trap classes exist: 1. Traps in substrate. The traps in the semi-insulating substrate generate I DS current transient states in relation to the VDS voltage variations: This phenomenon is named self-back-gating [25]. When VDS suddenly increases, many electrons are injected in the substrate and are captured by the traps. The global substrate charge becomes more negative, and a positive depletion region is created at the interface between the channel and the substrate. The channel section slowly decreases, as does the I DS current up to equilibrium. When the VDS voltage suddenly decreases, the traps emit many electrons in the channel. Then, the previous depletion region slowly narrows; the channel height increases, as does the I DS current up to its steady state. 2. Semiconductor surface traps. All the physical mechanisms are not yet explained, but these traps are responsible for the slow transient response of I DS current for a fixed VDS , when a sudden VGS variation is applied, from pinch-off to channel conduction [26]. This phenomenon is called gate lag. 3. DX traps in HEMT. These traps are located in the AlGaAs layer. They also generate the slow transient responses of I DS to a variation of VGS . Moreover, these traps induce transistor transconductance frequency dispersion. The difference between low-frequency and high-frequency transconductance values can reach 40% for high VGS values [27, 28]. Figure 4.8 depicts the drain current transient behavior due to the traps [25, 27]. The extraction method will be not developed in this chapter; more details can be found in [27]. Thermal Effects
The thermal effects in FETs have less importance than in bipolar transistors [29]. The only thermal-sensitive parameters of the model are the gate-drain and gate-source parameters I GDS , gd , I GSS , and gs and the I DSS and p parameters of the I DS current source [27]. Thermal dependence is written as
High-Frequency Oscillator Circuit Design
111
Figure 4.8 Substrate trap model.
I DSS = I dsst × exp (T /T ds ) + I dss 0 p = pt × T + p0 I GSS = I sgst × exp (T /T sgs ) + I sgs 0
(4.30)
gs = gst × T + gs 0 I GDS = I sgdt × exp (T /T sgd ) + I sgd 0
gd = gdt × T + gd 0 where I dsst , T ds , I dss 0 , p t , p 0 , I sgst , T sgs , I sgs 0 , gdt , gd 0 , gst , and gs 0 are fitting parameters. The introduction of the temperature in the electrical model is done with an equivalent parallel R th C th circuit, as it is for HBTs (Figure 4.3). The dissipated power is written as P diss = VGS I GS + VDS I DS
(4.31)
A second FET model, described in Section 4.1.3.3, is a nonlinear distributed model. It is the only model able to handle accurately the lowfrequency noise behavior of the FET under time-varying large signal operation. 4.1.3.3 FET Nonlinear Distributed Model
In oscillator circuits operating at microwave and millimeter waves under large-signal excitation, the previous lumped model does not allow for an accurate description of the interaction phenomena between the large-signal and the distributed low-frequency noise sources located into the transistor. This drawback is due to the active nature of the channel and the associated
112
RF and Microwave Oscillator Design
propagation phenomenon. Clearly, in nonlinear applications, the simulation of noise characteristics necessitates a nonlinear distributed model because the low-frequency noise sources are distributed along the active channel. For linear applications noise simulation does not need a distributed model: The Norton theorem applies. The noisy transistor is modeled by a noiseless transistor with two correlated noise current sources at its access ports (see Section 4.1.7). Then the noise characteristics can be computed at any external node in the circuit. Note that Norton theorem forbids any noise characteristic computation into the noiseless transistor, once the noise sources have been extracted. In nonlinear operation, before any application of the Norton theorem, the intrinsic nonlinear transistor must be transformed into a linear timevarying model. Then the Norton theorem applies and takes into account the interaction between the high-frequency applied large signal and the noise sources distributed along the channel. In this manner, the access ports’ noise sources are correctly extracted. To this end, an intrinsic nonlinear distributed model of FETs has been developed. It is fully based on measurement. The transistor channel is modeled by a nonlinear active transmission line [30]. The intrinsic transistor is sliced and modeled by a chain of N cells. Each cell (see Figure 4.9) represents the electrical behavior of a transistor slice. Obviously, the number of cells, N, depends on the transistor gate length L and operating frequency. Practically, we found that for L ≤ 0.3 m, N = 10 is a good compromise between the accuracy and complexity of this model. Every unit cell includes a nonlinear gate channel capacitance C G = f C (Vg k ), in parallel with a Schottky diode I G = f G (Vg k ). These elements are only a function of their own port voltage Vg k . Each cell also includes a nonlinear channel current–controlled source I C = f I (Vg k , ⌬Vc k ) that depends on its own port voltage ⌬Vc k and on the controlling voltage of the cell Vg k . At last, two linear fringing capacitances are added at the source and drain end of the channel. They take into account the capacitive coupling effects between the metallic electrodes and the edge channel. The other extrinsic linear parasitic elements are described by lumped elements as in the Pi model of Figure 4.7. It must be pointed out that the nonlinear functions f Q , f G , and f I are identical for all the unit cells. Nevertheless, the unit cell voltages Vg k and ⌬Vc k vary along the channel from source to drain. It results in an accurate nonlinear, nonuniform, distributed model of the channel.
High-Frequency Oscillator Circuit Design
113
Figure 4.9 Topology of the intrinsic distributed model along the gate.
Moreover, since the model is inherently non-quasi-static, it does not need the inclusion of any time delay, nor a questionable charging resistor Ri . Channel Current Source Expressions
The channel voltage–controlled current source of every unit cell is expressed with (4.23), which is similar to the I DS current source of the lumped model. To improve the circuit simulator convergence, a modification of the discontinuity condition due to the VGSN sign is introduced. This condition is replaced by a ⌫ function: ⌫(VGSN ) =
1 (tanh (Pe ⭈ VGSN ) + 1) 2
(4.32)
Two expressions are defined for I C following the ⌬Vc k sign: • For ⌬Vc k < 0
I C neg (Vg k , ⌬Vc k ) = Gd 0 ⌬⌬V k + I N 1 (Vg k + VGN )2 ⌬⌬V k2 + I N 2 ⌬⌬V k4 (4.33) with
114
RF and Microwave Oscillator Design
GD 0 =
∂I C pos (Vg k , ⌬Vc k ) ∂⌬Vc k
|
⌬Vc k = 0
and where I N 1 , I N 2 , and VGN are fitting parameters. • For ⌬Vc k > 0 I C pos (Vg k , ⌬Vc k ) = I DSS × f g × f d × Correct_Gm × ⌫(V GSN ) (4.34) and the whole expression is written as I C (Vg k , ⌬Vc k ) = I C pos (Vg k , ⌬Vc k ) × ⌫(⌬Vc k ) + I C neg (Vg k , ⌬Vc k ) × (1 − ⌫(⌬Vc k ))
(4.35)
An example of this function is plotted in Figure 4.10. Nonlinear Diode and Capacitance
The I Gk diode and the C Gk capacitance functions are the same as those of the lumped model equations (4.25) and (4.26):
Figure 4.10 I C (Vg k , ⌬Vd k ) function.
High-Frequency Oscillator Circuit Design
冉
115
冊
Vg k
I Gk = I GDS e gd U T − 1
(4.36)
and
C Gk (Vg k ) = Cg 0
冉
Veff 1− Vb
冊冉 n
冊
1 1 (Vg k − V t ) − (Vg k − V b ) + C b 2d 1 2d 2 (4.37)
with Veff =
1 V + Vb (d 1 − d 2 ) + t 2 2
d1 =
√(Vg k − Vb )
2
+ d2
d2 =
√(Vg k − Vt )
2
+ d2
All the models we have presented have been extracted from measurements. Now, in Section 4.1.4, the pulsed measurement system dedicated to transistor isothermal characterization is described. Then the model-extraction strategies for HBT and FET transistors are explained, and some examples are given. 4.1.4 Transistor I-V and S-Parameter Measurement System Measurement-based models take into account real-world devices, including all the parasitics [31]. They are well-suited for circuit CAD database optimizations and statistical approaches to ensure successful designs of MMICs. The measurement approach requires accurate, repeatable, and safe measurements of the devices. Three families of electrical measurements can be mentioned to proceed to complete extraction models: I-V, S-parameters, and low-frequency noise. 4.1.4.1 Pulse I-V Measurement Setup
To provide suitable models for microwave-circuit CAD, the characterization of microwave devices should be realized with measurement conditions as close as possible to the real-world operating conditions. Temperature time constants of microwave transistors are very high compared with the RF
116
RF and Microwave Oscillator Design
period. Thus, the device temperature does not change during an RF period; thermal drift depends on the average power dissipated inside the device. Because transistor characteristics strongly depend on device temperature, a realistic device characterization must be performed isothermally, at a device temperature as close as possible to its real-world temperature. Starting from the dc quiescent point, short pulses are used to measure the device behavior isothermally. Pulses from 150 ns to a few microseconds can be used, depending on the device. The measurement principle is shown in Figure 4.11 (extracted from [31]) for an FET. VGS 0 , VDS 0 , and I DS 0 correspond to the quiescent point, and VGSi , VDSi , and I DSi are the pulsed point values. The shorter the pulses, the closer the device is to its RF behavior. The pulse duration and duty cycle must be adapted to the DUT, as a compromise between several points: • The pulse width must be large enough for quality of measurement
acquisition.
Figure 4.11 I-V pulse principle. (Source: [31], 1998, IEEE. Reprinted with permission.)
High-Frequency Oscillator Circuit Design
117
• The pulse width must be much smaller than thermal time constant
for isothermal characterization. • The pulse width must be smaller than the trapping time constant, if traps exist. • The pulse duty cycle must be large enough to ensure that the thermal state is driven by the dc quiescent point. • The pulse duty cycle must not be too large to ensure fast and reliable data acquisition with averaging. A duty cycle of 0.1–5% is usually acceptable, but it must be checked for each transistor. This can be done easily with a few measurement points [32]; the pulse durations have to be tested in the same manner. Pulse widths from 300 ns to 600 ns are usually suitable, but pulses as short as 150 ns can sometimes be required for some millimetric HEMTs, due to fast trapping effects. 4.1.4.2 Measurements
Four electrical quantities are measured simultaneously during the pulse, with high accuracy for modeling purposes. This can be done either with a fourchannel GPIB oscilloscope, or with VXI digitizers. The voltage probes are classical high-impedance, low-capacitance active or passive probes. Two configurations allow for the measurement of the currents: differential probes associated with accurate external resistors and Hall probes. All combinations are available for the input and the output of transistors, depending on the current ranges. Our system with its probes provides a specified dc voltage offset accuracy better than 0.25% ± 5 mV up to ± 10V after warm-up and without averaging. Temperature measurements are made with the device inside a thermal enclosure; its temperature should be controlled by software for extensive characterization. 4.1.4.3 Pulsed S-Parameter Measurements
Pulsed S-parameters measurements are performed by superimposing an RF stimulus during the I-V pulses. A vectorial network analyzer (VNA) with short-pulse (≤ 150 ns) capabilities is required for the isothermal measurement of transistors. With these long pulse durations compared with RF periods, and with four identical measurement paths for the transmitted and reflected signals from the DUT to the samplers, the VNA quickly reaches a CW mode during the pulses.
118
RF and Microwave Oscillator Design
Bias tees with a dc bandpass allow I-V pulses to connect the VNA to the I-V setup—see Figure 4.12 (adapted from [31]). A time synchronization between equipment places the RF measurements precisely during the I-V pulses and avoids phase jitter. Depending on device technology and size, RF power levels in the DUT planes between −12 dBm and −21 dBm are suitable for small-signal S-parameter measurements. This level is checked by biasing the device in a nonlinear region (usually at pinch-off for FETs) and by monitoring the trace on the oscilloscope: If the RF level is set too high, the drain current increases by self-biasing during the RF pulse. Moreover, this test is a good way to check the RF pulse position versus the bias pulses. 4.1.5 Model Extraction Procedure From the measurements presented in Section 4.1.4, the whole model extraction can be handled. The base of this work is an optimization procedure of
Figure 4.12 I-V and RF pulse setup. (Adapted from [31].)
High-Frequency Oscillator Circuit Design
119
all the parameters included in a homemade software. The optimization algorithm relies on simulated annealing [33, 34] and simulated diffusion [35], which avoid local minima. However, a brute optimization is not desirable for two main reasons: first because a high number of parameters must be optimized to obtain accurate fitting functions and second because some of these parameters must have physical significance. Accordingly, a gradual modeling approach is more advisable. Our software permits this tuning by continuously displaying the measured and calculated curves. Modeling methodologies have been developed for the two types of transistors: bipolar and field effect. 4.1.5.1 Bipolar Transistor Model Extraction
The procedure is divided into four progressive steps: the electrothermal convective model (I CT and diode currents), the extrinsic elements extraction (parasitic capacitances and inductances), the nonlinear capacitances and transcapacitances, and finally the thermal capacitance and resistance [10, 12]. Electrothermal Convective Modeling
The transistor characteristics used for this extraction are the Gummel plot (collector and base currents versus VCE = VCE in logarithm axes) and the input and output characteristics, I CT (VCE ) for constant I B and VBE (VCE ) for constant I B . The parameter extraction steps are the following: • Determination (graphical and numerical) of R E , I SE , fE , E ,  f ,
and I SFE from the Gummel plot [see Figure 4.3 and (4.3) and (4.6)]; • Numerical optimization of the parameter set of the base collector junction (I SC , c , I SFC , fC ), R C , and reverse  R current gain, deduced from the input and output measured characteristic curves; • Numerical optimization of the whole model by taking the previous results as initial guess values. These three steps are repeated for different temperatures, by modifying only the thermal-dependent parameters [see (4.13)–(4.16)]. An example of an HBT convective model is shown in Figure 4.13. Figure 4.13 shows the comparison between the measured and computed input and output characteristics, at two different temperatures: 53°C and 79°C. Extrinsic Elements Extraction
This linear model extraction method combines a direct extraction method [36] with a numerical one. In the HBT linear model (Figure 4.4), the R BC ,
120
RF and Microwave Oscillator Design
Figure 4.13 Comparison between the measured and computed input and output characteristics, at two different temperatures: 53°C and 79°C.
R BE , G m , G d , R C , and R E are fixed from the previous convective extraction (derivatives of nonlinear function at the bias point). The other capacitive, inductive, and R B elements are extracted at the same time, and for some bias points in the region where the transistor operates. The goal of this optimization is to obtain extrinsic elements independent of the bias point and of the frequency. Typically the measured frequency range is from 2 GHz to 40 GHz. An example is given in Figure 4.14 for two bias points: VCE = 2.4V with I C = 100 mA and VCE = 10V with I C = 25 mA. Nonlinear Capacitances and Transcapacitances
The modeling procedure is described as follows: • Extraction of C BC capacitance and C BEC transcapacitance from
S-parameter measurements;
High-Frequency Oscillator Circuit Design
121
Figure 4.14 S-parameters measured and computed from 2 GHz to 40 GHz.
• Fitting the parameters C jC 0 and ⌽C of the junction C jC capacitance,
(4.7) and the parameters C BCd 0 of the diffusion C dC capacitance, and (4.9) from the plot of base-collector capacitance versus base collector voltage; • Fitting the parameters C BEc 0 and C BEc 1 of the transcapacitance
C dEC and (4.12) from the plot of base-emitter capacitance versus base collector voltage. • Extraction of C BE capacitance and C BEC transcapacitance from
S-parameter measurements; • Fitting the parameters C jE 0 and ⌽E , of the junction C jE capacitance,
(4.8) and the parameters C BEc of the diffusion C dE capacitance, and (4.10) from the plot of base-emitter capacitance versus base emitter voltage;
122
RF and Microwave Oscillator Design
• Fitting the parameter C BCe of the transcapacitance C dCE and (4.12)
from the plot of base-collector capacitance versus the base emitter voltage. These steps are repeated versus temperature. By numerical optimization, the coefficients C BEd 0 , C BEd 1 , C BCe 0 , and C BCe 1 are computed. Thermal Model Extraction Thermal resistance determination. The method is based on isothermal measures. The first step is to measure the I CT (VBE ) characteristic for a given VCE and different junction temperatures fixed by the thermal enclosure in which the transistor is placed with very short pulse durations to maintain the transistor to a constant temperature during measurement. The second step is to measure this same curve with dc bias. The superimposition of these two measurements on the same plot allows one to determine the thermal resistance (Figure 4.15): At each intersection of the dc curve and one of the pulsed curve, the dissipated power is given by the dc curve and the temperature is given by the pulsed curves. The plot of the ratio between the dissipated power and the temperature directly gives the thermal resistance value.
Figure 4.15 Determination of correspondence between dissipated power and junction temperature.
High-Frequency Oscillator Circuit Design
123
Thermal time constant determination. In this method, one measures the VBE
voltage evolution during a long pulse in the way that the voltage decreases while the temperature increases. An example of such a measurement is shown in Figure 4.16. Knowing the thermal resistance, the thermal capacitance can thus be deduced from the relation [18, 37]:
th = R th C th
(4.38)
In conclusion, the complete modeling of bipolar transistors necessitates all the described extraction methods and the associated measurement setup. However, depending on the intended application of the transistor—mixer, oscillator, linear, or power amplifier—only a part of this modeling may be achieved. An example of an HBT model is provided in Appendix 4A. Now, Section 4.1.5.2 discusses the FET extraction model. 4.1.5.2 FET Extraction Model
Two different models have been developed for the FET. This section first describes the classical Pi model and then discusses the distributed model essential to accurate noise modeling for nonlinear applications. Pi Model
As for the bipolar transistor, progressive steps are necessary to completely extract the transistor model.
Figure 4.16 V BE voltage pulse measure; determination of thermal constant.
124
RF and Microwave Oscillator Design
Extraction of parasitic elements. This is a direct extraction from the measurement of two transistor configurations [38]. A first measurement of the transistor for VDS = 0 is achieved for two VGS bias voltages. For a positive VGS , the gate to the source diode is in conduction region. Then, the Z-parameter computation allows for the determination of the ‘‘series’’ elements: L G , R G , L S , R S , L D , and R D .
Z 11 = R G + R S +
RC + R GS + j (L S + L G ) 3
Z 21 = Z 12 = R S +
RC + j L S 2
(4.39)
Z 22 = R D + R S + R C + j (L S + L G ) where R C is the channel resistance (foundry parameter) and R GS is the incremental resistance of the Schottky diode. For a large negative VGS , the transistor can be considered to be an open circuit, and the capacitances can be obtained from Y-parameter computation: Im (Y 11 ) = j (C pg + 2C b ) Im (Y 21 ) = Im (Y 12 ) = −jC b
(4.40)
Im (Y 22 ) = j (C b + C pd ) where C b is the capacitance of residual coupling between electrodes. This extraction method is coupled with an optimization procedure to find all the linear elements of the transistor model, frequency-independent [39]. Extraction of the linear model. This procedure is summarized in Figure 4.17.
To extract the intrinsic model of a transistor (Figure 4.7), successive matrix transformations enable us to eliminate the parasitic elements. The intrinsic elements (C GD , R GD , G D , C DS , C GS , R i , G m , ) are directly calculated from the Y-parameters following formulas given in [38]. We obtain, for each element, a set of values corresponding to each measurement frequency. An example of extracted parameters is shown in Figure 4.18. Note that the elements must be frequency-independent. Nonlinear convective model extraction. From the I DS (VGS , VDS ) measurements, the fitting parameters of the nonlinear function I DS (VGS , VDS )
High-Frequency Oscillator Circuit Design
125
Figure 4.17 Linear model extraction.
[(4.22)] and those of the drain-source breakdown current source function [(4.28)] I BDS (VGS , VDS ) are extracted by numerical optimization. From the I G (VDS , VGS ) and for low VDS , the fitting parameters of the gate-source and gate-drain diodes I GS (VGS ) and I GD (VGD ) function [(4.23) and (4.24)] are determined, while for high VDS , the fitting parameters of the gate-drain breakdown current source I BGD (VGS , VDS ) function [(4.27)] are computed. The same optimization procedure as for bipolar transistor is employed. The transistor characterization is performed for several temperatures and the thermal dependence of the I G , I D diodes and I DS current source functions [(4.29)] are fitted versus temperature.
126
RF and Microwave Oscillator Design
Figure 4.18 Element extraction verification.
The model consistency is checked by a comparison of the extracted linear elements G D and G m with those calculated from the linear model. Nonlinear capacitances model extraction. This procedure is the same as for the bipolar transistor. Fitting functions are found from the collection of linear capacitance values: C GS and C GD are obtained from linear model extraction as a function of VGS and VDG bias voltages. Thermal circuit extraction. This procedure is based on the measurement of the thermal variation of the Schottky junction threshold voltage. In the first step, the I GS (VGS ) characteristic is measured at several temperatures. Then, for constant I GS current, the VGS voltage is plotted versus temperature. The slope of this curve is a well-known result (between −1 mV/°C and −1.4 mV/°C). In a second step, the same transistor characteristic is measured for several dissipated powers. As for the bipolar transistor, the superimposition of the two characteristics allows for the evaluation of the thermal resistance [27].
High-Frequency Oscillator Circuit Design
127
To evaluate the thermal time constant, drain bias pulses are applied to the transistor. During the bias pulse, a low-level RF signal is applied, and the transistor S 21 parameter is measured (see Figure 4.19). The FET gain exponentially decreases, and the slope at the origin gives the thermal time constant and the thermal capacitance is deduced with the relation (4.38). An example of a Pi model of HEMT is given in Appendix 4A. Section 4.1.5.3 deals with the FET-distributed model, including the low-frequency noise sources. 4.1.5.3 HEMT-Distributed Model Extraction
The distributed model under the gate from source to drain is composed of N identical cells. This number must be chosen in consideration of the function of the gate length L g ; for example, for L g < 0.3 m, 10 cells are a good compromise between the model accuracy and the complexity of the model extraction [40]. The extraction procedure consists of the same three steps as for the Pi model. The computation of the extrinsic elements, including the drain
Figure 4.19 Thermal gain decrease in the RF measurement window.
128
RF and Microwave Oscillator Design
source capacitance, is performed following the procedure described in Section 4.1.5.2 for the simple Pi model [41]. Convective Model Extraction
The second step is the convective model extraction. Since the nonlinear elements take the same form for all the cells, only one parameter set is to be computed from the I-V characteristic. The procedure is a whole numerical optimization that also computes all the internal node voltages Vg k and ⌬Vc k (k = 1–10). These voltages are only dependent on the external voltages VGS and VDS and on the cell number. Figure 4.20 shows a comparison between the I DS (VGS , VDS ) characteristics computed with a 10-cell model and the measured one. In this example the transistor is a PHEMT with four fingers of 50 m width by 0.25 m length. Figure 4.21 shows Vg k and ⌬Vc k voltages (k = 1–10) computed from the model, for external bias voltages VGS = −0.2V and VDS = 3.5V. Capacitances Extraction
The two fringing linear C bs and C bd capacitances and the nonlinear C Gk (Vg k ) capacitance are extracted at the same time. They are extracted from the S-parameter measurements in the same way as for the Pi model.
Figure 4.20 Comparison between the I DS (V GS , V DS ) characteristics, measured and computed with the distributed model (10 cells).
High-Frequency Oscillator Circuit Design
129
Figure 4.21 Internal voltage Vc k and Vg k for fixed external bias voltages.
At last, an example of a comparison between S-parameters measured and computed with the nonlinear distributed model is shown in Figure 4.22. This electrical model, fully extracted from measurements, is the first that is able to handle the distributed low-frequency noise sources. Section
Figure 4.22 Comparison of the S-parameters measured and modeled with the nonlinear distributed model (V GS = −0.2V and V DS = 2.52V).
130
RF and Microwave Oscillator Design
4.1.6 describes and models the main noise sources in the bipolar transistors and FETs. 4.1.6 Noise Sources in Semiconductor Devices and Their CAD-Oriented Modeling An electrical noise signal may be mathematically represented by an infinite sum of pseudosinusoidal components, with random amplitudes and phases. In a CAD-oriented model, a noise source ␦ h (t ) will be represented by:
␦ h (t ) =
√2 ∑ ᑬ (H n e
j n t
)
(4.41)
n
where √ 〈 | H n | 2 〉 is the rms value of the Fourier component, centered at n , in a 1-Hz bandwidth. The power spectral density of this component will be written as: S ␦ h ( n ) = 〈 | H n | 〉 2
(4.42)
4.1.6.1 Noise Sources in Semiconductor Devices
Four main physical noise sources must be considered in the design of low phase-noise oscillators. For a good understanding of the noise origin, let us consider the current flowing in a slice ⌬x of a semiconductor sample. In a one-dimensional model, at an abscissa x , the current I (x ) writes as in relation (4.21) I (x ) = qA (x ) n (x ) v (x )
(4.43)
The current through the slice will fluctuate if at least one of the quantities A (x ), n (x ), and v (x ) (the ensemble average velocity of carriers) fluctuates. Obviously, in a bulk sample, A (x ) cannot fluctuate. Accordingly, the noise sources inside the sample come from the following: • Carrier density fluctuations; • Velocity fluctuations.
Carrier density fluctuations lead to generation recombination noise (G-R) and the associated so-called nonfundamental 1/f noise [42–46].
High-Frequency Oscillator Circuit Design
131
Velocity fluctuations lead to diffusion noise in ohmic semiconductors, the collective approach of the shot noise in semiconductor junctions, and finally to the fundamental 1/f noise through the 1/f random fluctuations of the low-field carrier mobility 0 and/or the diffusion coefficient D 0 . G-R and 1/f noise are colored noise. They are called low frequency excess noise because their power spectral densities fall, respectively, with a and 1/ , in function of frequency. roll-off of 1 + 2 ⭈ 2 In nonlinear circuits such as mixers and oscillators, the mixing of the low-frequency noise sources with the carrier signal frequency gives rise to AM and PM noise spectra near the carrier. In conclusion, four main physical noise sources are to be considered in oscillator circuits. Their power spectral densities are described in the following equations: • White noise sources: •
Diffusion noise in ohmic semiconductor regions: For a dc-applied voltage, the power spectral density of the equivalent Norton source of the slice ⌬x is written as: S ␦ i ( ) =
4q 2n 0 D 0 A ⌬x
(4.44)
At low field, the conductance of the slice is written as: G 0 = qn 0 0
A ⌬x
(4.45)
By taking into account the Einstein relation, one obtains: S ␦ i ( ) = 4kTG 0 •
(4.46)
Shot noise in semiconductor junctions: Neglecting the transit time of carriers, the power spectral density of the equivalent Norton noise source of a junction is written as: S ␦ i ( ) = 2qI 0 where I 0 is the current flowing in the junction.
(4.47)
132
RF and Microwave Oscillator Design
• Low-frequency noise sources: •
Generation recombination noise: In the slice ⌬x , the current due to carrier density fluctuations is written as:
␦ I = qA␦ n (x ) v 0
(4.48)
giving rise to a power spectral density S ␦ i ( )GR =
q 2A 2v 20 S ␦ n ( )
=
q 2v 20 ⌬x 2
S ⌬N ( )
(4.49)
where ⌬N is the total number of fluctuating carriers in the volume of the slice ⌬xA . For G-R noise sources generated by a single trap with a single time constant , one has S ⌬N ( ) = 4⌬N 2 •
1 + 2 2
(4.50)
Fundamental 1/f noise: The fluctuating current is written as:
␦ I = qAn 0 ␦ v 0
(4.51)
At low field: ␦ v 0 = ␦ 0 E 0 . The resulting power spectral density is S ␦ i ( )1/f =
I 02
20
S ␦ 0 ( )
(4.52)
where I 0 = qAn 0 0 E 0 . 4.1.6.2 Noise Source Behavior in Semiconductor Devices, Driven by RF Time-Varying Signals White Noise Sources
The white noise sources’ behavior under large signals excitations is now well understood. The autocorrelation functions of white noise sources are Dirac delta functions. It is assumed that the noise mechanism follows the RF frequency of the modulating signal [47–50].
High-Frequency Oscillator Circuit Design
133
Let us write a white noise source as:
␦ i (t ) = M (t ) U (t )
(4.53)
where M (t ) is the deterministic modulating function of the applied voltage and U (t ) is a primary white noise source. The pseudosinusoid component of U (t ), centered at the frequency ⍀ is written as: U (t , ⍀) =
√2ᑬ (U˜e
j ⍀t
)
(4.54)
Moreover, in oscillator circuits M (t ) is periodic and can be expanded in Fourier series: k = +N H
M (t ) =
∑
k = −N H
M k e jk 0 t
(4.55)
with M k = M k* Finally, ␦ i (t ) becomes: 1 ␦ i (t ) = √2
k = +N H
∑
k = −N H
˜ e j (k 0 + ⍀)t + U ˜ *e j (k 0 − ⍀)t ) M k (U
(4.56)
This resulting source is called a cyclostationary noise source. This representation may be applied to diffusion and shot noise [47–50]. Low-Frequency Noise Sources
The behavior of the low-frequency noise sources in the presence of timevarying signals is more involved, because their autocorrelation functions are not Dirac delta functions (i.e., their spectra are colored). To explain the modulation mechanism, let us write, for example, the G-R noise current given by the relation (4.48):
␦ i (t ) = q
v ⌬N (t ) ⌬x
(4.57)
where v = 0 E . Let us suppose that the electric field E is now time-varying. We obtain:
134
RF and Microwave Oscillator Design
␦ i (t ) =
q E (t ) ⌬N (t ) ⌬x 0
(4.58)
In (4.58), E (t ) contains dc and RF frequency components and ⌬N (t ) only low-frequency noise components. Due to the large time constants involved in the physical mechanism giving rise to the carrier number fluctuations ⌬N (t ), it results that it cannot follow the RF-applied voltage. Nevertheless, ⌬N (t ) is multiplied by E (t ) to give rise to the Norton current source ␦ i (t ), which is so modulated at the RF frequency. The initial low-frequency spectrum of ⌬N (t ) is transposed around the Fourier components of the RF applied voltage [51, 52]. It may be conjectured that the same explanation holds for the fundamental 1/f noise. From (4.51), we obtain:
␦ i (t ) =
I (t ) ␦ 0 (t ) 0
(4.59)
I (t ) is now a time-varying current, and ␦ 0 (t ) is a low-frequency fluctuation. Then ␦ i (t ) contains low-frequency and RF frequency components. To model the noise sources and their modulation coefficients, they must be accurately localized into the semiconductor devices. For example, in an HEMT device, G-R noise sources may originate from the following: • Access resistances; • The supplier layer, under the gate; • The channel itself; • The buffer layer; • The semiconductor surfaces, between the gate drain or gate source.
Actually, the main problem of a CAD-oriented accurate modeling of the noise sources is rightly to find these origins. That is why this domain remains an open topic. 4.1.7 Transistor Low-Frequency Noise Characterization 4.1.7.1 Introduction
This section describes accurate noise measurement techniques used to characterize the noise in FETs and bipolar transistors. The experimental noise
High-Frequency Oscillator Circuit Design
135
measurement setup is presented. Direct determinations of noise generators at the input (gate or base) and the output (drain or collector) are first developed. They are followed by a technique of simultaneous noise measurement of these two generators leading to the correlation between noise sources. In all the cases noise-equivalent circuits are given, and noise calculations are presented in detail. Some remarks are given about the used methodology. The experimental procedure is discussed, and typical results are presented. 4.1.7.2 Noise Representation in Linear Two-Port Devices
In linear two-port networks the noise is taken into account by at least two noise voltage and/or current generators associated with the input and/or the output [53, 54]. This leads to six equivalent noise representations, each of which is naturally associated with a particular matrix of the two-port device. Generally for FETs or bipolar transistors, two noise representations are currently used. In the first, the real network can be seen as equivalent to an ideal noiseless network together with a series voltage noise generator and a shunt current noise generator at the input port (see Figure 4.23). In the following section, noise generators will be presented with the same symbols. In the second representation the real network is associated to an ideal one with shunt current noise generators at each port (see Figure 4.24). For FETs in a common source configuration, the input noise generator is related to the gate current noise, whereas the output one describes the channel noise. For bipolar transistors in common emitter bias, the input noise generator is associated with emitter-base junction and the output noise source with base-collector and emitter-collector carrier diffusion. In general, it should be noted that the noise at each port arises from different contributions of the same internal noise generators and so the
Figure 4.23 Noise representation of a two-port device with noise generators at the input port.
136
RF and Microwave Oscillator Design
Figure 4.24 Noise representation of a two-port device with parallel current noise generators at each port.
equivalent noise generators at the two ports are partially correlated. This remark applies for all the equivalent representations. Classical Noise Analysis
Figure 4.23 allows us to derive the expression of the noise figure of the twoport network when its input is loaded by a source signal generator with a source resistance R S as in Figure 4.25. We have [53] (in the following and for noise measurement purposes we consider ‘‘spot’’ frequency relationships): F( f ) = 1 +
1 [S ( f ) + R S2 S ni ( f ) + 2R S ᑬ (S nv , ni ( f ))] 4k B TR S nv (4.60)
In (4.60) we suppose that R S exhibits only thermal noise; k B is the Boltzmann constant; S nv ( f ) and S ni ( f ) are the spectral densities of the two input noise generators; and S nv , ni ( f ) is their cross-spectrum if these two generators are correlated. On the other hand, the total noise power at the output of the network is proportional to:
Figure 4.25 Noise circuit for noise figure calculation.
High-Frequency Oscillator Circuit Design
137
P out ≈ 4k B TR S + S nv ( f ) + R S2 S ni ( f ) + 2R S ᑬ (S nv , ni ( f )) (4.61) So, if the input load resistance of the device has a low value, S nv ( f ) dominates and the voltage noise generator can be characterized. On the contrary, for a large value of the input load, the current noise generator is evaluated. The knowledge of the noise figure, which is the third noise parameter of the two-port device, allows us to determine the cross-spectrum S nv , ni ( f ). This characterization leads to a global evaluation of the noise but does not allow an investigation of the internal noise generators. In fact, for the determination of S ni ( f ) we must use values of R S larger than the input resistance of the device. This is possible for bipolar transistors in common base or common emitter configurations. Unfortunately, in the case of FETs this method cannot be applied. Noise Measurements for Accurate Characterization
For accurate noise studies the methodology of noise measurements stems from the noise equivalent circuit of Figure 4.24, and the two noise current generators are directly analyzed [55, 56]. Moreover, simultaneous measurements of these generators allow us to obtain their correlation. From the equivalent circuit of the two-port device being tested, the located noise sources can be determined. Section 4.1.7.3 presents these techniques. 4.1.7.3 Experimental Setup
Figure 4.26 reports the noise measurement setup used for the characterization of FETs. (A similar one is used for bipolar transistors.) In this case simultaneous noise measurements at the input (gate or base) and at the output (drain or collector) can be achieved. Vector signal analyzers with two channel inputs allow the measurement of the spectral density of each injected signal, the measurement of the complex cross-spectrum of the two signals, and the coherence between them. The coherence function is defined as: ⌫( f ) = | S VAVB ( f ) | /{S VA ( f ) S VB ( f )} 2
(4.62)
The noise experimental setup requires low-noise amplifiers and vector signal analyzers. They are the main parts of the apparatus. FFT analyzers are advantageously used in low-frequency noise measurements because they are easy to work up. They do not imply calibration by
138
RF and Microwave Oscillator Design
Figure 4.26 General layout for the noise measurement setup.
noise standards and allow direct measurement if the gains of the amplifiers are known. (The FFT analyzer can be used as a network analyzer to determine it.) Actual FFT analyzers work up to 10 MHz (HP 89410A) and can be associated with RF converters for measurements above this limit. Low-noise amplifiers are now available for noise characterization. Tables 4.1 and 4.2 provide examples of the typical characteristics of voltage or transimpedance amplifiers well-suited for noise analysis. The typical input background noise of these amplifiers is reported in Figures 4.27, 4.28, and 4.29. It can be noticed that the cross-spectrum of the input noises of these two amplifiers lead to a negligible coherence function. Figure 4.30 shows the noise experimental setup and the connections between the different parts. 4.1.7.4 FET Noise Measurements Direct Gate Noise Measurements
The gate noise is associated with the low gate currents and involves high impedances. It is measured by the help of ultra-low-noise transimpedance Table 4.1 Typical Characteristics of the 5003 EG&G BROOKDEAL Voltage Amplifier
5003
Input Noise S eA (f )
k
Bandpass
ZE
1,000
0.1 Hz–1 MHz
> 1 M⍀//10 pF Figure 4.27
Re q = S i /4kT White Noise 75⍀
High-Frequency Oscillator Circuit Design
139
Table 4.2 Typical Characteristics of the 5182 EG&G BROOKDEAL Transimpedance Amplifier 5182 k′ Bandpass Input resistance Maximum input current Input noise equivalent current S i /2q Input noise S i′A (f )
S = 10−8 Low Noise S = 10−7
S = 10−6
108 0.5 Hz–10 kHz < 10 k⍀ 100 nA 500 pA
107 0.5 Hz–200 kHz < 100⍀ 10 A 50 nA
106 0.5 Hz–800 kHz < 1⍀ 1 mA 6.2 A
Figure 4.28
Figure 4.29
Figure 4.27 Input noise of the EG&G 5003 amplifier.
amplifiers. This type of amplifier allows for a direct determination of the noise current spectral density. In this case the output of the transistor is ac short-circuited, and the configuration of the device is given in Figure 4.31. The noise equivalent circuit of this setup is given in Figure 4.32.
140
RF and Microwave Oscillator Design
Figure 4.28 Input noise of the EG&G 5182 transimpedance amplifier (k ′ = 108).
S i ′ ( f ) is the spectral density of the noise current generator i A′ (t ) A associated with the background noise of the amplifier. For a normal use of this amplifier, only this noise generator is needed to take into account the amplifier noise. S i Gm ( f ) is the spectral density of the noise current generator i Gm (t ) associated with the gate current. G Gm is the low-frequency conductance seen at the input of the amplifier. k ′ is defined as v ′S /i ′e . So we have [57] S iG ( f ) = m
1
| k ′ |2
Sv ′ ( f ) Si ′ ( f ) S
A
(4.63)
Direct Channel Noise Measurements
Channel noise is generally related to higher currents and lower impedances than for gate noise analysis. So, except for critical situations such as very low noise levels near the cut-off voltage or in the saturation range, this noise can be obtained using low-noise voltage amplifiers. In this case the noise
High-Frequency Oscillator Circuit Design
141
Figure 4.29 Input noise of the EG&G 5182 transimpedance amplifier (k ′ = 107).
voltage spectral density is determined. The noise current is then calculated taking into account the values of the channel and load resistances. Channel noise is directly measured as shown in Figure 4.33; the gate circuit is now ac short-circuited. In fact, to avoid oscillations, the transistor is biased with a bias-tee as shown in Figure 4.34. Its bandpass is 10 MHz to 1.5 GHz and for noise measurements in the range 1 Hz to 1 MHz, the transistor load remains R P . The noise equivalent circuit of this setup is given in Figure 4.35. So we have S vS ( f ) = | k |
2
再冉
R P R Dm R P + R Dm
冊
2
冎
[S i D ( f ) + S i P ( f )] + S e A ( f ) m
(4.64) 4k B T as the thermal noise of the load resistance R p , and k as RP the voltage amplification. S i D ( f ) is the spectral density of the channel noise and R Dm is its m dynamic resistance. For correct use of a low-noise voltage amplifier, only with S i P =
142
RF and Microwave Oscillator Design
Figure 4.30 (a) The connections between the different parts of the experimental setup and (b) view of the experimental noise measurement setup.
High-Frequency Oscillator Circuit Design
Figure 4.31 Transistor configuration for gate (input) noise measurements.
Figure 4.32 Noise equivalent circuit for Figure 4.31.
Figure 4.33 Transistor configuration for drain (output) noise measurements.
143
144
RF and Microwave Oscillator Design
Figure 4.34 Transistor bias including the bias-tee.
Figure 4.35 Noise equivalent circuit for Figures 4.33 and 4.34.
the noise voltage generator e A (t ) is necessary to describe the background noise of this amplifier. The measured spectral density of the channel S i D ( f ) is then m
S iD ( f ) = m
冉
1 1 + R P R Dm
冊再 | | 2
S vS ( f ) k
2
冎
− S eA ( f ) −
4k B T RP
(4.65)
In the ohmic range R Dm is easily measurable and R p is chosen as R p >> R Dm . So (4.64) becomes:
High-Frequency Oscillator Circuit Design
S iD ( f ) = m
1
S VS ( f )
(R D m )2
| k |2
S eA ( f )
145
(4.66)
In saturation, if R Dm >> R p , it is not necessary to determine R Dm . Nevertheless, R p must chosen to minimize its noise contribution. In the general case, (4.64) applies. Simultaneous Channel and Gate Noise Measurements
For these measurements the schematic setup configuration of Figure 4.26 is used. To determine the two signals received by the two channels of the analyzer, a general equivalent noise circuit of Figure 4.26 is taken into account. This equivalent circuit is given in Figure 4.36. The intrinsic transistor in a common source configuration is given as an active two-port circuit ( y 1 , y 2 , y 3 , g m int v GS int ) with additional terminal access resistances (R G , R S , R D ). To these three resistances are associated noise generators i R G , i R S , i R D , whereas, for the intrinsic part, i ch int is the channel noise and i g s and i g d are the noise generators of the admittances y 1 and y 3 . R P and i p are, respectively, the load resistance and its noise generator assuming only thermal noise. For the other noise generators, they can take into account several noise sources, such as 1/f noise, G-R noise, thermal, or shot noise. The voltage amplifier is characterized by its gain k , its input resistance R E , and its input noise generator e A . In a same way k ′, i A′ , and R E′ characterize the transimpedance amplifier. For the evaluation of the spectral densities associated with VS and VS′ we use the spectral densities that characterize the various noise generators and the complex impedances or admittances of the circuit. After several manipulations and transformations in the electrical form of the equivalent circuit (see Appendix 4B), we obtain [see (4B.21b), (4B.28b), and (4B.29b)]:
Figure 4.36 Noise equivalent circuit for simultaneous input-output noise measurements.
146
RF and Microwave Oscillator Design
|
ZS S VS ( f ) = | k | S eA ( f ) + ZS + RP 2
再 +
S ⑀2 ( f ) +
|
|
Z 21 Z 11 + R E′
| | 再 再再
Z 21 Z 11 + R E′
S VS′ ( f ) = | k ′
2
2
| 冎
2
|
2
|
|
RP S ep ( f ) + | k | ZS + RP 2
S ⑀ 1 ( f ) − 2ᑬ
再冉
冊
2
S eA′ ( f )
S iA′ ( f ) +
− 2ᑬ
冎
Z 21 (S ⑀*1 ⑀ 2 ( f )) Z 11 + R E′
(4.67) 1
| Z E′ | 2
| 冎 |
冋
S ⑀1 ( f ) +
冎
Z 12 Z 22 + R P
Z 12 Z 12 S (f ) + Z 22 + R P ⑀ 1 ⑀ 2 Z 22 + R P
| |
2
S ⑀2 ( f )
册冎
2
S eq ( f )
(4.68) S V S VS′ ( f ) =
再
冉
冊
kk ′*R P Z 21 Z 12 * S ⑀1 ( f ) S ⑀2 ( f ) * Z + R ′ ′ Z E (Z S + R P ) Z 11 + R E ′ 22 P + S ⑀ 1⑀ 2 ( f ) +
(Z 22
冎
Z *12 Z 21 S ⑀* ⑀ ( f ) + R P )* (Z 11 + R E′ ) 1 2
(4.69)
with S eq ( f ) = S e p ( f ) +
R P2 R E2
S eA ( f )
(4.70)
S ⑀ 1 ( f ) = | z 2 + z 3 | S i GS ( f ) + | z 3 | S i chint ( f ) + | z 2 | S i GD ( f ) 2
2
2
+ S eG ( f ) + S eS ( f )
(4.71)
S ⑀ 2 ( f ) = | z 3 + | S i GS ( f ) + | z 1 + z 3 | S i chint ( f ) + | + z 1 | S i GD ( f ) 2
2
+ S eD ( f ) + S eS ( f )
2
(4.72)
S ⑀ 1 ⑀ 2 ( f ) = (z 2 + z 3 )(z 3 − )*S i GS ( f ) + z 3 (z 1 + z 3 )*S i chint ( f ) − z 2 (z 1 + )*S i GD ( f ) + S e S ( f )
(4.73)
High-Frequency Oscillator Circuit Design 2
147
S eG ( f ) = R G S iR G ( f )
(4.74)
z 12 z 21 z 22 + R P
(4.75)
Z E′ = z 11 −
2
S eS ( f ) = R S S iR S ( f )
(4.76)
z 12 z 21 z 11 + R E′
(4.77)
Z S = z 22 −
2
S eD ( f ) = R D S iR D ( f )
(4.78)
Remarks
We have presented two methodologies to obtain input (at gate or base) and output (at drain or collector) noise sources: a direct noise measurement of these two noise generators and a simultaneous one that allows us to achieve cross-spectrum and correlation between the input and output noise sources. Obviously these two methodologies must lead to the same results concerning input and output noises. So it is necessary to verify that the measured values obtained at one input of the analyzer are not damaged by the other channel measurements. In particular, the experimental conditions introduced in Appendix 4B must be satisfied. Moreover, for PHEMTs and other structures with large drain current and high output conductance, the load resistance R P must be small enough to avoid inaccurate correlation measurements. On the other hand, the obtained cross-spectrum between input and output noise generators is a complex quantity and (4.69) must be considered as two equations. The dynamic signal analyzer gives the Cartesian or the polar representations of this quantity. Then it appears that the gains of the used amplifiers must be constant in magnitude and phase over the whole frequency range of noise investigations to avoid acute corrections. The above noise calculations apply for FETs or bipolar transistors since the same small signal equivalent circuit and noise generator location can be considered. Nevertheless, the conduction mechanisms and the noise source origins are quite different [53, 54]. Moreover, at high frequencies the behavior of FETs is taken into account as an active transmission line, and it will be shown that the noise sources must be in fact distributed along active RC networks. In all cases, the four relations given by (4.67), (4.68), and the real and imaginary parts of (4.69) can be used as a basis of the noise characterization
148
RF and Microwave Oscillator Design
of two-port semiconductor devices. The four corresponding unknown quantities are the two noise current generators (at the input and the output of the intrinsic part of the device) and their correlation (the real and imaginary part of the cross-spectrum, for example). The other noise sources are located at the parasitic conduction paths. These parasitic elements and their associated noise sources can be predominant for particular biases of the devices and must be determined for an accurate noise characterization. Several contributions [55–63] describe basic investigations into FETs and bipolar transistors. 4.1.7.5 Experimental Procedure
To obtain the noise characterization of the device (i.e., the behavior of all the noise sources versus biases and frequency), two steps must be achieved: The small signal equivalent circuits is determined, and the various noise sources are extracted from the previous noise measurements. Small Signal Equivalent Circuit
From the conduction model of the device, the equivalent circuit of the intrinsic part of the device is determined. This implies the knowledge of the involved characteristic conduction parameters (or their extraction procedure; see [60] for an example). In this procedure the parasitic access resistances are also obtained. Their values can also be extracted from RF scattering parameter measurements. For FETs y 1 and y 2 in Figure 4.36 take into account two equivalent diodes located between gate and source and gate and drain, respectively. These two diodes are in shunt configuration with very low-leakage conductances. The study of the gate current versus various gate and drain biases allows us to obtain these conductances and the characteristic parameters of the diodes [60]. So all the parts of the equivalent circuit are known at each quiescent point of the device. Noise Extraction
In low-frequency noise analysis we expect white noise (thermal noise and shot noise) and excess noise (1/f noise, generation-recombination noise with Lorentzian spectra) [53, 54]. Thermal noise is associated with ohmic paths as parasitic access resistances or leakage conductances. It is the fundamental noise level for channel noise in FETs [53]. Shot noise is the fundamental noise level associated with diode conduction. Hence it is the basic source in bipolar transistors [53]. The 1/f noise is always present when electrical conduction occurs in semiconductor devices, and this noise source can be located at any part of the device [64]. Its magnitude is linked to the fluctuations of the electrical conductivity and to the quality of the technology [65].
High-Frequency Oscillator Circuit Design
149
Generation-recombination noise appears when trapping and detrapping of charge carriers occurs. This is due to particular defects in the device structure or to specific semiconductor materials [55, 65, 66]. In all the cases the noise characterization starts from the identification of these elementary noise sources. Each noise device must be studied versus bias to separate the contribution associated with the intrinsic transistor from the parasitic parts [60]. As expected, the analysis leads to the model of each noise source associated to the device giving its behavior versus bias, frequency, and geometry. Various papers can be considered to make clear this purpose [65–73]. Experimental Results
Some experimental results about GaAs-based PHEMTs are presented, obtained with the previous noise investigation techniques. Figure 4.37 reports the variations of the 1/f noise in the channel as S i D ( f )/I D2 . It can be shown [62] that at a low effective gate voltage the first two behaviors are related to the intrinsic channel, whereas at high gate biases the noise stems from access resistances.
Figure 4.37 Related 1/f channel noise versus effective gate bias showing various behaviors and involving intrinsic channel and access resistances. Here k is a conduction parameter of the device [62].
150
RF and Microwave Oscillator Design
Figure 4.38 shows the 1/f gate noise evolution S i G ( f ) versus the current of diode D 3 located between gate and drain for VGS < 0 (diode D 1 reverse-biased) and 0 < VDS < 3V (diode D 3 forward-biased). The noise follows a quadratic law versus I D 3 as expected for the 1/f noise source. It is related only to D 3 since its magnitude is i -independent. Figure 4.39 reports the coherence function measured for VGS = −0.4V and VDS = 3.75V and the computed values from (4.67), (4.68), and (4.69) after determination of the small-signal equivalent circuit at this bias point and characterization of the noise sources.
4.1.8 Modeling of Circuit-CAD–Oriented Noise Sources in HBTs and FETs This section deals with noise source modeling, which must be inserted in the transistor models:
Figure 4.38 1/f gate noise evolution versus the transistor bias. In this case 1/f noise of D 3 is obtained.
High-Frequency Oscillator Circuit Design
151
Figure 4.39 Example of coherence function measurement and simulation for V GS = −0.4V and V DS = 3.75V.
• In a distributed way for FETs; • As lumped sources in bipolar transistors (at least in first realistic
approach). Due to the strong transistor technology dependence (MESFETs, HEMTs, homojunction bipolar transistors, and HBTs) of the LF noise behavior, a transistor generic model with parametric noise sources expressions is not realistic. Only the noise source locations in the electrical model and their representation by a current or voltage source (described by their pseudosinusoids—see Section 4.1.6) will be defined for each transistor class (FET or bipolar). Finally, an example of a PHEMT LF noise source extraction from measures will be shown. 4.1.8.1 Noise Sources in HBT
The linear Pi HBT model is described in Section 4.1.2 and depicted in Figure 4.3. Strictly speaking, R B is a distributed resistance [74] but it can
152
RF and Microwave Oscillator Design
be taken as a lumped element. The following noise sources have to be considered in HBT [75]: White Noise Sources • Thermal noise sources: They are associated to the resistances R B and
R E . The power spectral density of a thermal noise current source is written as S ␦ i Th =
4kT R
(4.79)
where R can be either R E or R B . T is the resistance temperature. The noise source of R C can be neglected. • Shot noise sources. Van der Ziel [53] has shown that shot-noise in
bipolar transistors can be represented by two uncorrelated current sources: • One in parallel across the intrinsic base-emitter junction: ␦ Ib shot ; • One in parallel across the intrinsic collector-emitter junction: ␦ Ic shot . Their power spectral densities are written as: S ␦ Ib shot = 2qI B
(4.80)
S ␦ Ic shot = 2qI C
(4.81)
Numerical comparisons between the contribution of the noise sources ␦ Ib shot and ␦ Ic shot on the resulting phase noise of several oscillator circuits have been performed. They show that ␦ Ic shot plays the major role, at least in the circuits simulated. Low-Frequency Noise Sources
According to their technology dependence, location determination of the low-frequency noise sources in HBT is more involved. Simultaneous measurements of the low-frequency noise currents at the transistor input and output in function of the bias voltage, for a wide range of the source resistances, allows for discrimination between all the possible locations of the lowfrequency noise sources. Their power spectral density and correlation can
High-Frequency Oscillator Circuit Design
153
be extracted in a function of the base or collector current. Then, for circuitCAD purposes, analytical fitting functions must be found before to include them in HBT nonlinear models. Practically, the main low-frequency noise sources are the following: • First, the low-frequency fluctuations of the base current due to: •
Fluctuations of the surface recombination velocity; Generation-recombination inside the base junction; • 1/f fluctuations of the diffusion coefficient of the minority carriers. • Second, the low-frequency fluctuations of the resistance R B and R E : • Generation-recombination due to the traps; • 1/f fluctuations of the mobility. •
Figure 4.40 shows the resulting HBT model with the noise sources described above: All are uncorrelated. It must be noted that, fortunately, in a transistor many of them can be neglected, according to the technology. 4.1.8.2 LF Noise Model of FET and Associated Extraction
In oscillator circuits based on FET, low-frequency noise sources are practically the main causes of the resulting phase noise. The FET LF noise model is
Figure 4.40 HBT nonlinear model with noise sources.
154
RF and Microwave Oscillator Design
established from the distributed nonlinear model seen in Section 4.1.3.3. Generally speaking, each unit cell, includes two noise sources (Figure 4.41). Of course, according to the transistor technology, one of these sources can be neglected. To insert the noise sources in the model, the experimental characterization step is first performed, with the measurement setup described in Section 4.1.7. The two intrinsic power spectral densities Si Gm (gate terminal) and Si Dm (drain terminal) are extracted, in a frequency band from 100 Hz up to 1 MHz for several bias points in the normal operating region of the transistor. Each spectral density depends on three variables: VGS , VDS , and frequency. As an example, Figure 4.42 shows the plot of Si Dm spectral density at a 1-kHz frequency spot, versus VDS and for different VGS . As expected in FET, these measures show that the Si Dm power spectral density is higher than the Si Gm by several orders of magnitude. Moreover, only G-R noise appears in the measures. It may be conjectured that in this example only the ␦ Ic k channel current noise source is to be considered. The second step consists of the extraction of the internal noise sources of the unit cell ␦ Ic 2k as shown in Figure 4.41. Each unitary noise source is supposed to be uncorrelated with the others. Then a relation between all the elementary sources and the measured one at the access port can be written as: N
Si Dm =
∑ | H k | 2 ␦ Ic 2k
k=1
Figure 4.41 LF noise sources of one distributed FET model cell.
(4.82)
High-Frequency Oscillator Circuit Design
155
Figure 4.42 Example of Si Dm spectral density measure.
where H k is the transfer function between the source number k and the external noise current. These transfer functions H k are computed for the 10 cells of the nonlinear model, by linearizing it around the bias point. Now, in the third step, an expression of the unitary noise sources must be found. This calculation is detailed in [76]. The simplest expression relating Si Dm to the local noise source is written as: N
Si Dm = KI C
1 ∑ | H k | 2 ⌬x k
(4.83)
k=1
where K is a fitting constant depending on the material allowing for the adjustment of the model with the measures, ⌬x k the representative length of the cell. This equation is a function of the spot noise frequency and bias point (VGS , VDS ). Figure 4.43 shows an example of Si Dm computed with the distributed model and measured for noise frequency of 1 kHz.
156
RF and Microwave Oscillator Design
Figure 4.43 Comparison between measured Si Dm spectral density and the computed one with the LF noise model.
The correspondence between the two results appears very satisfying, owing to the simplicity of noise current source equations. More accurate modeling can be reached with the counterpart of the more involved fitting equation. In conclusion, this extraction procedure applied to G-R noise sources of the channel can be extended to other noise sources. However, the goal of CAD-oriented modeling is to find a compromise between the model accuracy and ease of use in a CAD environment. To complete the noise model, thermal noise sources of the resistances R g , R s , and R d must be added.
4.2 Oscillator Circuit Design Tools 4.2.1 Conventional Linear Theory of Sinusoidal Oscillators The basic linear operating principles of sinusoidal oscillators will not be discussed here. However, the success obtained in past years by the wellknown negative-conductance concept [77] leads us to carry out a very simple basic calculation to clarify the relationship between the negative-conductance and feedback loop concepts in transistor oscillators.
High-Frequency Oscillator Circuit Design
157
4.2.1.1 Negative-Conductance Concept Applied to a Transistor Oscillator Circuit
The basic oscillator topology is shown in block diagram form in Figure 4.44. In Figure 4.44, the oscillator is represented by the following: • An active amplifying device: the transistor; • An amplitude-limiting and amplitude-stabilizing device; • A frequency-determining element or feedback network.
A very common form of amplitude stabilization is to use the nonlinearity of the active amplifying device. So common applications use the transistor as a self-limiting element. To present the concept of negative conductance, we will use a quasilinear representation of the oscillator circuit as shown in Figure 4.45. This quasi-linear representation allows a very simple analytical calculation. It will be performed in the admittance formalism. Analog (but not identical) results can be obtained with the impedance formalism. We assume that the input and output admittances are reactively tuned to the desired oscillation frequency 0 , so Y in | 0 = G in
(4.84)
Y out | 0 = G out where G in and G out are, respectively, input and output conductances.
Figure 4.44 Functional diagram of microwave transistor oscillators.
158
RF and Microwave Oscillator Design
Figure 4.45 Quasi-linear representation of the oscillation circuit for negative conductance calculation.
The resonator LC is also tuned to the chosen oscillation frequency 0 . The load resistor is connected in parallel with the conductance of the resonator in order to obtain a total load conductance: G load . In addition, to calculate the input admittance at the oscillation frequency 0 , the circuit is driven by an external sinusoidal current I 0 ( ). The whole admittance observed at the input is written as G tot =
I0 Vin
|
0
= G in + N 2(G out + G load ) − NG mo
(4.85)
This conductance can be split into a passive conductance: G p = G in + N 2(G out + G load )
(4.86)
in parallel with a negative conductance due to the transconductance G mo of the transistor: −G active = −NG mo
(4.87)
This active conductance is negative due to the positive feedback introduced by the (out-of-phase) transformer. Near the oscillation frequency 0 , the total input admittance can be expressed as:
High-Frequency Oscillator Circuit Design
Y ( 0 + ⌬ ) = G tot ( 0 ) +
dG tot dB ⌬ + j tot ⌬ d d
159
(4.88)
dB tot is the total susceptance slope to be seen on the input of this d very simple oscillator circuit.
where
4.2.1.2 Open-Loop Approach
We can redraw the circuit of Figure 4.45 as shown in Figure 4.46, in which the input sinusoidal current source has been replaced by an external voltage E ext ( ) controlling the output current source of the transistor modeled once again by its equivalent linear transconductance G mo . The complex open-loop gain is defined as: ˜ ol = Vin G E ext
|
(4.89)
A straightforward calculation shows that at 0 : ˜ ol = G
NG mo 2
G in + N (G out + G load )
=
G active G passive
Figure 4.46 Open-loop representation of the oscillator circuit.
(4.90)
160
RF and Microwave Oscillator Design
The total input conductance of the circuit is written as: G tot = G passive − G active
(4.91)
Thus, G tot is immediately written as ˜ ol ( 0 )) G p ( 0 ) G tot ( 0 ) = (1 − G
(4.92)
which is the desired result. Thus, it can be seen clearly that when G tot < 0
(4.93)
˜ ol > 1 G
(4.94)
then
So, it comes down to the same thing to study autonomous circuits through the negative conductance concept or with the open-loop gain technique. More generally, when complex admittances are to be handled, the previous relation becomes: ˜ ol ( )) Y p ( ) Y tot ( ) = (1 − G
(4.95)
The study of transistor oscillators with the open-loop gain concept is extremely judicious and will make it easy to study, for example, linear and nonlinear stability, by using commercially available software tools, as will be seen later. 4.2.1.3 Free-Running Oscillator Start Conditions
The circuit is now investigated in the complex-frequency plane: p = ␣ + j . The input admittance becomes: ˜ ol ( p )) Y p ( p ) Y in ( p ) = (1 − G
(4.96)
This linear input admittance is that of the circuit when turning on the power supply. It is obtained by replacing all nonlinear elements of the circuit by their incremental small-signal values at the chosen quiescent point.
High-Frequency Oscillator Circuit Design
161
An instability will appear in the circuit at an angular frequency 0 , if the current and voltage variables can be written at turn-on as:
␦ X (t ) = ␦ X 0 e ␣ 0 t cos ( 0 t + )
(4.97)
␣0 > 0
(4.98)
with
Since the circuit is autonomous, its equation can be written as: Y in ( p ) ␦ Vin ( p ) = 0
(4.99)
The requirement that ␦ Vin ( p ) ≠ 0 leads to the necessary condition: Y in ( p ) = 0
(4.100)
˜ OL ( p )) Y p ( p ) = 0 Y in ( p ) = (1 − G
(4.101)
besides
But Y p represents a passive admittance; therefore, it cannot contain any zeros with a positive real part (i.e., ␣ 0 > 0). So this clearly implies that (4.102) has to be satisfied. ˜ OL ( p ) = 1 G
(4.102)
The rigorous (4.102) allows for the determination of possible instabilities in the circuit. The zeros of this equation with a positive real part P 0 = ␣ 0 + j 0
(4.103)
P k = ␣ k + j k represent the possible complex oscillation frequencies of the circuit. It must be noted that (4.102) and (4.103) do not guarantee that the oscillation will grow until a stable large signal steady state is reached. They only guarantee that the dc operating point is unstable. This is the first
162
RF and Microwave Oscillator Design
condition to set up oscillations in the circuit. The growth or quench of the oscillation depends on the nonlinear transient behavior of the circuit. ˜ OL ( p ) Referring to the simple but illustrative example of Figure 4.46, G writes: ˜ OL ( p ) = G
NG mo 2
G in + N (G out
1 + G load ) + C p + Lp
=1
(4.104)
and as G p = G in + N 2(G out + G load ) ˜ OL ( p ) = G
NG mo Gp + C p +
1 Lp
=1
(4.105) (4.106)
or equivalently,
冦冋
G p − NG mo + C␣ +
C−
1 L (␣ 2 + 2 )
␣ =0 L (␣ + 2 ) 2
册
(4.107)
=0
and, finally, we find two complex conjugate roots ␣ 0 ± j 0 , with
冦
␣0 =
NG mo − G p 2C
20
2R
=
冉
NG mo − G p − 2C
冊
2
(4.108)
where
2R = If NG mo > G p , then ␣ 0 > 0.
1 LC
(4.109)
High-Frequency Oscillator Circuit Design
163
We observe that the start frequency 0 is nearest to R when NG mo is nearest to G p and when the selectivity of the tank circuit, which is proportional to 2C , is the highest. Unfortunately, only a few standard simulators can perform this calculation in the complex-frequency plane [78]. ˜ OL ( j ) can be plotted [79]. Then However, the Nyquist diagram G ˜ one can verify that the locus of the G OL ( j ) encircles the critical point: (1,0). A Bode plot can also be drawn [79]. It appears to be a very useful tool. Let us write ˜ OL ( ) | e j ( ) ˜ OL ( ) = | G G
(4.110)
˜ OL | and ( ) are plotted versus frequency. The 20 log | G Three conditions are necessary in a single-frequency parallel tuned oscillator, in order to obtain a growing oscillation from the noise floor of the oscillator circuit.
冦
˜ OL | > 0 20 log | G
( 0 ) = 0 d <0 d 0
|
(4.111)
The Nyquist diagram and/or the Bode plot can be drawn using any simulator software. (See the benchmark in Appendix 4C: The example shows two possible oscillation frequencies. Readers are invited to find the stabilizing circuit to eliminate the spurious frequency.) The oscillation start conditions in an electrical circuit are directly linked with the stability of the operating point. A detailed analysis can be found in Chapter 2. No matter which method is used to analyze the oscillation start, the designer must ensure that the circuit will only start at a frequency very close to the one selected, and that no other spurious oscillation frequency is present. Failing to take this precaution into account might result in serious trouble when launching the industrial production of the circuit. Figure 4.47 shows the simulated results of linear open-loop gain as function of the angular frequency (Bode plot) of a single transistor MMIC HEMT oscillator circuit. We observe in Figure 4.47(a) that a spurious oscillation can appear at f s = 800 MHz, whereas it has disappeared in Figure 4.47(b) owing to circuit stabilization.
164
RF and Microwave Oscillator Design
Figure 4.47 (a) Simulation results of linear open-loop gain for an MMIC HEMT oscillator and (b) simulation results of linear open-loop gain for an MMIC HEMT oscillator with circuit stabilization.
Note that the open-loop gain required in p = ␣ + j plane, for oscillation ˜ OL small-signal ( p ) = 1, with ␣ > 0. to take place, is G ˜ OL steady-state ( p ) = G ˜ OL steady-state ( j 0 ) = In the steady state, ␣ = 0 and G 1, so that it can be said that the open-loop gain of an oscillator circuit is always, in the complex plane, ˜ OL ( p ) = 1 G with ␣ > 0 during the transient and ␣ = 0 in the steady state.
(4.112)
High-Frequency Oscillator Circuit Design
165
On the other hand, at real frequencies, one has at turn-on
| G˜ OL small-signal ( j 0 ) | > 1
(4.113)
˜ OL steady-state ( j 0 ) = 1 G
(4.114)
and, in the steady state:
So the transistor works in the steady state with a gain compression: ˜ OL steady-state ( j 0 ) | C compression = 20 log | G
(4.115)
This enables the designer to choose the compression gain at which the transistor will work in the nonlinear steady state. It can be found, at the first order, by a simple linear calculation. Note that for a fixed nonlinear steady state oscillation waveform, the gain compression varies according to the transistor biasing mode: constant voltage, constant current, self-biasing, or feedback biasing. 4.2.1.4 Oscillation Start in Symmetrical Oscillator Circuits
Differential and push-push structures are widely used at RF and microwaves, owing to their easy implementation on a monolithic chip. Moreover, it has been shown that these structures lead to low phase noise, owing to their odd or even symmetry with respect to both loop oscillation and the main low-frequency noise sources in transistors. Figure 4.48 shows a symmetrical structure obtained by cascading two identical active two-port devices. Choosing a chain matrix representation, we obtain in the complexfrequency plane p = ␣ + j :
Figure 4.48 Symmetrical oscillator.
166
RF and Microwave Oscillator Design
冋 册 冋 册冋 V1( p ) I1( p )
=
A
B
V2( p )
C
D
−I 2 ( p )
册
(4.116)
册
(4.117)
and
冋 册 冋 册冋 V 1′( p ) I 1′( p )
=
A
B
V 2′( p )
C
D
−I 2′( p )
The connecting wires impose: I 1 = −I 2′ I 2 = −I 1′
(4.118)
V 1 = V 2′ V 2 = −V 1′ Then the equation of the circuit is written:
再冋
A−1
B
C
D−1
册冋
A+1
B
C
D+1
册冎冋 册
= 0 (4.119)
册冎
= 0 (4.120)
V1( p ) I1( p )
The oscillation start conditions become: det
再冋
A−1
B
C
D−1
册冎 再冋 det
A+1
B
C
D+1
which is the desired result. By inspection of the determinants, two possible modes of oscillation are obtained, namely, the odd and even modes. For the out-of-phase mode: V 1 = −V 1′. For the in-phase mode: V 1 = V 1′. To eliminate the undesired mode, the architecture of the active twoport devices must be carefully designed: • The use of the out-of-phase mode leads to differential and push-
push structures, with good phase-noise characteristics and reproducibility (see example at the end of the chapter). • The in-phase mode is generally used to combine the output power of two (or more) identical oscillators.
High-Frequency Oscillator Circuit Design
167
4.2.1.5 Oscillation Start Conditions in Multitransistor Circuits
The governing equation that describes an autonomous linear circuit can be formulated as a matrix equation in the following form: ›
[H ( p )] ␦ X ( p ) = 0
(4.121)
›
In order to have solutions ␦ X ( p ) different from zero, the system determinant must be equal to zero. The roots of det [H ( p )] = ⌬( p ) = 0 must be calculated. If the designer has no dedicated tools to find these zeros, the determinant ⌬( j ) = 0 may be plotted in the complex plane and the encirclement of the critical point must be studied. Unfortunately, the resulting figure is generally too complicated to offer any particular interest. This is due to a lack of determinant normalization. In that case the system should rather be handled by plotting the normalized determinant function (NDF) [79, 80] or by computing the system’s eigenvalues [81]. This method will prove extremely effective even in the case of nonlinear analysis, as will be seen with the local stability of the oscillator steady state. After verifying the oscillation start conditions, the nonlinear steady state simulation will ensure that the circuit will oscillate properly. 4.2.2 Steady-State Analysis of Transistor Oscillators 4.2.2.1 Simulation Techniques
The oscillator steady state can be calculated by two general-purpose simulation techniques: • Time domain integration (TDI); • Harmonic balance (HB).
The most commonly used time domain simulation technique for steadystate autonomous circuits is the shooting method [82]. However, the HB method appears as the most widely used technique for RF, microwave, and millimeter-wave applications and it is well-suited for tackling efficiently the analysis of multitransistor circuits with distributed components, with reasonable computer simulation time. The latest generations of HB circuit simulators rely primarily on the modified nodal analysis (MNA) formulation to describe electronic circuits. This formulation proves efficient and accurate when HB applications are to
168
RF and Microwave Oscillator Design
be extended to the analysis of modulated signals and noise in nonlinear circuits. Other network formulating equations are possible in order to further reduce the system matrix size to be computed, but results may be insufficiently accurate to be used with the analysis of modulated signals and noise in nonlinear circuits. Finally, the computing time of nonlinear circuits has been dramatically reduced nowadays thanks to methods using Krylov subspaces to solve the network matrices. The use of Krylov subspace methods in circuit simulation has been proposed by Freund and Golub [83]. It significantly reduces the computer simulation time, which currently makes RF, microwave, and millimeter-wave circuit analysis by the HB method and its associated techniques, particularly efficient and reliable. For surveys and further references, we refer the reader to [84–90] for details on the principles and implementation of the HB method. 4.2.2.2 Simulation Results
The main output characteristics given by a circuit simulator are the following: • Oscillation frequency; • Node voltages (i.e., complex voltages at harmonic frequencies, or
time-domain waveforms); • Mesh currents; • Average power dissipated in the circuit elements. • Other characteristics required by the designer. 4.2.2.3 Conditions for a Successful Steady-State Simulation
Special care is needed in choosing the number of spectral components as well as the number of samples processed by HB simulators. As for the number of harmonics, it should obviously not be too small, to obtain accurate amplitudes and phases for the first few harmonic frequencies. Conversely, if the number of significant harmonics is too high, it can also lead to erroneous results owing to the limited frequency range validity of active and passive component models used by foundries. Some publications indicate simulations performed at millimeter waves with a number of harmonics higher than 10 without any indication of the frequency range validity of the models used. Harmful interactions at frequencies beyond which passive and active models are not valid must be avoided. These frequencies must be shortcircuited on the active device ports. With this precaution, a high number of harmonics can be used.
High-Frequency Oscillator Circuit Design
169
As for oversampling, a high number of samples are required to reach an accurate solution: Even if the simulated circuits are driven by quasisinusoidal voltages (variables), the resulting nonlinear currents (functions) are strongly nonlinear (e.g., exponential functions used in diodes and bipolar transistor models). To check the stability of the simulated steady-state solution, the nonlinear local stability analysis of the circuit must now be undertaken. 4.2.3 Nonlinear Stability of Free-Running Oscillators Two kinds of stability are to be studied in nonlinear oscillator circuits: global and nonlinear local. 4.2.3.1 Global Stability
A possible bifurcation of a stable oscillation regime toward another stable regime can be detected by means of the variation of one of the parameters of the circuit, such as the dc bias voltage or the value of an element of the circuit. The most commonly encountered bifurcations are described as follows: • Amplitude jump and hysteresis phenomena (direct bifurcation D-
type); • A sudden appearance of a divided-by-two solution of the fundamental frequency 0 (indirect bifurcation or I-type); • Appearance of spurious frequencies = ␣ ⭈ 0 with ␣ ∈ ᑬ and nonrational (Hopf bifurcation H-type). All these phenomena, which are very spectacular to observe experimentally, can now be subjected to a detailed theoretical study with commercial simulators [91–96]. Such analyses, however, require a lot of computer time and should be reserved—in our opinion—to verifying and diagnosing oscillator circuits suffering from working disorders. Nevertheless, it is important for a designer to know these tools so that he or she can make a diagnosis if necessary. Moreover, such tools will soon be implemented into many commercial simulators, thus enabling nonspecialists to use them. 4.2.3.2 Nonlinear Local Stability of an Oscillator
The aim of this analysis is to verify that no spurious oscillation can occur in the circuit under the desired stable oscillation frequency 0 , calculated
170
RF and Microwave Oscillator Design
previously. The nonlinear stability study can be carried out by a perturbation analysis of the periodic steady state. The principle of the analysis [78, 81, 95, 97, 98] consists of introducing a small-signal complex perturbation of the form: e (␣ + j )t
(4.122)
This small signal is superimposed on the oscillation steady-state signal obtained previously. Thus, the state variables controlling the nonlinear elements will be written in the steady state as k = +N
x ss (t ) =
∑
k = −N
X k e jk 0 t
with X −k = X k*
(4.123)
where N is the number of harmonics components and 0 is the fundamental angular frequency. Since the perturbing signal is small, higher order terms in may be neglected, and so, in the presence of this small-signal perturbation, the previous state variable expression becomes: x (t ) = x ss (t ) + ␦ x (t )
(4.124)
with the resulting perturbation k = +N
␦ x (t ) =
∑
k = −N
⌬X k e ␣ t e j (k 0 + )t
(4.125)
A nonlinear element y (t ) controlled by x (t ) will be written by neglecting higher order terms in . y (t ) = y ss (t ) + ␦ y (t )
(4.126)
with k = +N
␦ y (t ) =
∑
k = −N
⌬Y k e ␣ t e j (k 0 + )t
(4.127)
High-Frequency Oscillator Circuit Design
171
Finally, for the whole circuit, the resulting perturbation vectors of state variables ␦ x›(t ) and nonlinear elements ␦ y›(t ) are related by the Jacobian matrix [U ] of nonlinear elements. The terms in the Jacobian matrix [84] are simply the Fourier components of the derivative of the vector of nonlinear › › elements y (t ) with respect to the vector of state variables x (t ). This matrix is evaluated from the steady-state circuit analysis. By taking into account the nonlinear HB system of equations [78, 95, 98], the following perturbation equation in the complex-frequency plane can be written in matrix form: ›
{[1] − [A y ] [U ]} ⌬X = 0
(4.128)
where [1] is the identity matrix. [A y ] is the matrix of the linear circuit at frequencies: −j␣ + ( ± k 0 )). [U ] is the Jacobian matrix of nonlinear elements. The above equation is the basis of the local stability analysis of a nonlinear circuit in the presence of a periodic or quasi-periodic steady-state signal [78]. Several processing methods can be undertaken from this equation depending on the available simulators. The first method, both natural and clever, yet not so easy to implement, is to find the complex eigenvalues of this equation and extract the complex frequencies solutions for which ␣ > 0. Then we immediately obtain frequencies at which instability can occur with either (␣ > 0; = 0 or = imaginary) or (␣ > 0; ≠ 0 and real). This extremely efficient and rigorous method permits one to handle local stability analysis of oscillators in the presence of either periodic (CW) or quasi-periodic (modulated) steady-state solutions [78]. The calculation in the complex-frequency plane can be avoided by plotting the determinant of this equation in the j plane (i.e., by examining the resulting Nyquist locus). Unfortunately, as in the linear case discussed previously, the investigation of this diagram proves difficult for nonexpert designers who will find it very complicated and/or impossible to use. Once again, this is due to a lack of normalization of the resulting diagram. Another interesting computer approach to be performed consists of calculating the eigenvalues of the perturbed system in the j plane [81]. By appropriate eigenvalue ordering, the complete Nyquist plot in the j plane can be obtained, allowing a check of the clockwise encirclement of the
172
RF and Microwave Oscillator Design
critical point. This method ensures the normalization of the determinant characteristic through a simple Nyquist locus. The detailed implementation of this rigorous method in a commercial simulator will be found in [81]. More recently a simplified method was proposed [99]: It consists of injecting a small signal current perturbation I ( j ⍀) into one node of the circuit in presence of the large signal steady state. The impedance Z observed at the particular node where the current perturbation has been injected can be calculated. The frequency ⍀ has to be swept in a wide frequency range. The result is then subjected to system identification methods, which permit to progress from Z ( j ) to Z ( p ).
写 M
Z ( j ) —————> Z ( p ) = identification
( p − zi )
i=1
( p − pi )
(4.129)
For the small poles p i which have a positive real part, the circuit is unstable and unwanted oscillations might occur. This very attractive method presents a drawback; in fact, strictly speaking, the impedance observed on a particular node of the circuit may well not contain poles with positive real parts located elsewhere in the circuits. See, for example, circuits with unilateral elements. This drawback becomes obvious when the characteristic matrix of the circuit is investigated by inspection. So, as indicated by the authors of the method, the location of the small-signal current perturbation is crucial. It has to be a ‘‘nonisolated node.’’ In complex circuits combining an oscillator with buffers the input port of a transistor participating to the oscillation is a good choice. 4.2.4 Oscillator Phase-Noise Characterization One of the fundamental characteristics of an oscillator is its phase noise (PM) spectrum. This characteristic must be precisely assessed. The amplitude noise (AM) spectrum is not an essential characteristic owing to its low level (in general between −10 dB and −30 dB) as compared to the phase noise level. Moreover, one of the common oscillator applications is to be a local oscillator in receiver systems. In such applications, AM noise rejection can be achieved with balanced configurations. However, this characteristic can prove significant in some applications, where the transmitter must have a very low AM noise (e.g., in collision warning/avoidance systems in automotive applications).
High-Frequency Oscillator Circuit Design
173
4.2.4.1 Output Signal Spectrum
Phase and amplitude noise generation being a stochastic process, it is necessary to know: • The statistical properties of noise sources; • The nonlinear interaction between these random sources and the
circuit elements, which generates random fluctuations on amplitude and phase in a free-running oscillator circuit. To define the amplitude and phase fluctuations in terms of spectral power density or autocorrelation function, the stationarity of the random phenomena must be checked. Numerous controversial publications have been issued in the past years addressing the validity of the phase noise representation in free-running oscillators as a stationary process [100]. This problem has now been solved [101, 102], but designers should also have some knowledge of the hypotheses relevant to the simulation tools of which they make use. Strictly speaking, the oscillator phase noise is a nonstationary process, whereas amplitude noise is a stationary process. According to Rutman [101], the pure oscillator output signal can be expressed simply by: V (t ) = V 0 sin (2 f 0 t )
(4.130)
where V 0 and f 0 are nominal amplitude and frequency, respectively. The actual output signal can be expressed as: V (t ) = (V 0 + ⑀ (t )) sin (2 f 0 t + (t ))
(4.131)
where ⑀ (t ) and (t ) are amplitude and phase fluctuations, respectively. It must be pointed out that a frequency variation implies a related phase variation: More precisely, the instantaneous frequency is the time rate of change of phase divided by 2 . By definition, the instantaneous frequency can be written as: f (t ) = or else:
1 d (t ) 1 d [2 f 0 t + (t )] = f 0 + 2 dt 2 dt
(4.132)
174
RF and Microwave Oscillator Design
f (t ) = f 0 + ⌬ f (t )
(4.133)
with ⌬ f (t ) =
1 d 2 dt
(4.134)
The frequency noise ⌬ f (t ) is a stationary process as can be justified by physical considerations; then, (t ), which is denoted by t
(t ) = 0 +
冕
2 ⌬ f ( ) d
(4.135)
0
is, in general, a nonstationary process. It must be noted that a free-running oscillator does not have a reference phase. This assertion is best visualized by turning off then turning on a freerunning oscillator: Although the circuit goes back to the same oscillation frequency every time, there is no reason why its phase, once it has been turned on, should be related to the one observed at turn-off. As a matter of fact, an oscillator gradually loses memory of its original phase with time. The conventional example of phase noise generation is that of a theoretically ideal oscillator, with an internal white-noise source that generates a socalled phase diffusion process similar to the mathematically ideal Brownian motion. As was pointed out by Kuva¨s [103], phase diffusion is a slow process. So the linearization of equations involving the phase in stabilities is valid as long as short-term stability is concerned. It is theoretically demonstrated that stationary models can be adopted for the representation of phase fluctuations in free-running oscillators. On the other hand, formalisms related to cyclostationary random processes can be used to describe all nonlinear noise sources. To verify these assumptions, a series of numerical calculations have been carried out on many different oscillator circuits using reliable active and passive device models. In the benchmark, transistors were described with linear and/or cyclostationary white noise and/or colored noise sources. Circuit simulations have been successively carried out using a time domain Monte Carlo (TDMC) method developed by Bolcato [104] and a frequency domain method [105] developed in our laboratory [88]. Results obtained with the two methods have been successfully compared.
High-Frequency Oscillator Circuit Design
175
The TDMC method can be regarded as the most rigorous method for noise calculation in lumped nonlinear circuits and may be used as a reference for comparison purposes. The method analyzes the noise excitation and the deterministic signal together, without stationary approximation. However, a drawback of this TDMC method is its high amount of simulation time. The higher the numerical precision required, the more CPU time will be needed. The frequency-domain analysis is based upon the assumption of the stationarity of the phase noise process. It is derived from the HB method by a linearization of the nonlinear network equation around the steady-state solution to construct a linear time-varying model for noise analysis [106]. The nonlinear elements are represented by means of conversion matrixes directly derived from the HB Jacobian evaluated at the steady state, and on the representation of linear [107] and cyclostationary noise sources by their correlation matrices. Note that in our method primary noise sources can be located in any node of the circuit, which is not the case for all the methods of oscillator phase-noise calculation. In addition, the aforementioned method and the TDMC technique permit accurate handling of the slow and fast dynamics of the circuit, which is crucial for oscillator circuits with low-frequency noise sources (i.e., generation-recombination and 1/f noise sources). The circuit example described in Appendix 4C verifies all these properties. The required computing time to simulate noise spectra with the frequency-domain method is extremely reduced as compared to the oscillation steady-state calculation. In conclusion, despite the theoretical problems that may arise concerning the stationarity of phase noise, (t ) may be assumed as a stationary process: Its one-sided spectral density S ( f ) and its double-sided spectral density L ( f ) can be defined from the Fourier transform of the autocorrelation function R ( ). The concept of S ( f ) [101, 108] is recognized today as the established fundamental quantity for the characterization of phase noise in free-running oscillators. 4.2.4.2 Oscillator Phase Noise Calculation in the Frequency Domain by Means of Conversion Matrices Formalism
The output waveform for an oscillator can be expressed as:
冉
V (t ) = V 0 1 +
冊
⌬v (t ) cos ( 0 t + 0 + ⌬ (t )) V0
(4.136)
176
RF and Microwave Oscillator Design
where V 0 is the peak amplitude of the carrier 0 . 0 is the phase of the carrier frequency at t = 0. ⌬v (t ) is the amplitude noise modulation. ⌬ (t ) is the phase-noise modulation. The AM and PM noise modulations can be expressed as pseudosinusoids at the noise frequency ⍀. ⌬v (t ) = ⌬V 0 cos (⍀t + A )
(4.137)
⌬ (t ) = ⌬ 0 cos (⍀t + )
(4.138)
where 〈 ⌬v 2(t ) 〉 and 〈 ⌬ 2(t ) 〉 denote the associated spectral densities. By introducing (4.137) and (4.138) into (4.136) and assuming that the amplitude of these modulation indexes are very small in comparison with the carrier signal, the voltage V (t ) contains three components at the following frequencies: • Carrier frequency: 0 ; • Lower sideband frequency: 0 − ⍀; • Upper sideband frequency: 0 + ⍀.
These components are evaluated with the software tool based on the linear time-varying approach and lead to the following expression:
冋
V (t ) = V 0 cos ( 0 t + 0 ) +
V⌬ cos [( 0 − ⍀)t + ⌬ ] V0
+
V⌺ cos [( 0 − ⍀)t + ⌺ ] V0
册
(4.139)
According to the conventional definition of AM and PM modulations, we can define AM noise at an offset frequency ⍀ from the carrier as:
冋册 N C
at ⍀ dBc
= 10 log
P ssb (AM ) by hertz P carrier
(4.140)
High-Frequency Oscillator Circuit Design
177
PM noise at an offset frequency ⍀ from the carrier as: L at ⍀ = 10 log dBc
P ssb (PM ) by hertz P carrier
(4.141)
The above-mentioned definitions are the ratio of the single sideband noise power spectral density (in a 1-Hz bandwidth at ⍀ offset from the carrier) to the total carrier power. Let us write in complex notation: ⌬V 0 e j A ⌬V˜ = V0 V0 ⌬ 0 e j = ⌬˜ V⌬ e j ⌬ = V˜⌬
(4.142)
V ⌺ e j ⌺ = V˜ ⌺ By identifying (4.136) with (4.139) and by taking into account (4.137), (4.138), and (4.142), we obtain the following expression for the amplitude and phase noise spectra 2 | V˜⌬* e j 0 + V˜ ⌺ e −j 0 | 2 P ssb (AM ) | ⌬V˜ | = = P carrier V 02 V 02
(4.143)
| V˜⌬* e j 0 − V˜ ⌺ e −j 0 | 2 P ssb (PM ) 2 ˜ = | ⌬ | = P carrier V 02
(4.144)
and finally the PM-AM complex correlation C=
⌬V˜ ⌬˜ * V 02
=j
1
(|V⌺ | V 02
2
− | V⌬ | 2 + 2j Im (V⌬* V ⌺ e 2j 0 )) (4.145)
The PM-AM noise spectra and the AM-PM noise correlation spectrum of free-running oscillators can be calculated using the above-mentioned equations. Note that there may be some confusion between two quantities that permit the ‘‘measurement’’ of oscillator phase noise.
178
RF and Microwave Oscillator Design
Let us write the oscillator signal as: V (t ) = V 0 cos ( 0 t + ⌬ (t )) = V 0 cos ( (t ))
(4.146)
where ⌬ (t ) and cos ( (t )) are fluctuating quantities. Remember that the standard definition of phase noise is S [⌬ ]⍀ : that is, the spectral density of phase fluctuations with ⌬ (t ) calculated at ⍀ offset from carrier [108]. However, in some publications, phase noise is expressed as S [cos ( )]⍀ , where the spectral density of cos [ (t )] is calculated at ⍀ offset from carrier. By invoking the relation between the autocorrelation function of ⌬ (t ) and of cos [ (t )], the relation between S [⌬ ]⍀ and S [cos ( )]⍀ may be found. Nevertheless, the two ‘‘measures’’ must not be confused. As an example, the asymptotic behavior of phase noise near the carrier, in an oscillator with white noise sources, may be calculated. By neglecting the low-frequency dynamics of the circuit, one finds that: • S [⌬ ]⍀ varies as K /⍀2. • The associated S [cos ( )]⍀ varies as
K1 K 22
+ ⍀2
S [⌬ ]⍀ is measured by passing the signal through a phase detector, whereas S [cos ( )]⍀ is directly observable on a spectrum analyzer, if the AM noise is negligible. The numerical processing of the AM and PM noise spectra with a simulator software package is described in the following equation. 4.2.4.3 Description of the Numerical Method
Applying Kirchoff’s current law in the time domain to all the nodes of a general autonomous circuit, we can obtain the well-known conventional nonlinear equation i(v(t)) +
d q(v(t)) + y(t) * v(t) + i G = 0 dt
(4.147)
where t is the time; v(t) is the vector of node voltage waveforms; i G is the vector of independent sources; i(t) represents all the nonlinear current sources and q(t) all the nonlinear charges; and y(t) represents the impulse response matrix of the linear circuit.
High-Frequency Oscillator Circuit Design
179
Steady State
If we expand all the previous variables in truncated complex Fourier series, and we call Y the Fourier transform of impulse response y(t), we obtain the steady state in the frequency domain: I(V 0 ) + j ⍀Q(V 0 ) + YV 0 + I G = 0
(4.148)
where I(V 0 ) denotes the current-voltage dependence of the nonlinear conductances and Q(V 0 ) describes the dependence of the charge stored in the nonlinear capacitors on the voltages. ⍀ is a diagonal matrix representing the frequency domain differentiation operator. V 0 denotes a nontrivial solution of (4.148) and characterizes the oscillator steady-state node voltages. Noise Analysis
Let us assume that the noise sources do not perturb the large-signal steady state of the circuit. From this postulate, we can apply the frequency conversion analysis to determine noise voltage and current anywhere in the circuit. Let us consider the time domain steady-state solution v 0 (t ) of (4.147) corresponding to the phasor representation V 0 in the frequency domain and superimpose a small perturbation to it: v(t) = v 0 (t) + ␦ v(t)
(4.149)
Thus, the system of the nonlinear equations can be linearized around the steady state d i(t) dv
|
v 0 (t )
␦ v(t) +
冉 |
d d q(t) dt dv
v 0 (t )
冊
␦ v(t) + y(t) * ␦ v(t) = b(t) (4.150)
where b(t) describes all the possible forms of the modulated noises sources. It can be expressed as: b(t) = m(t) n(t)
(4.151)
For the sake of clarity, let us express the primary noise source n(t) [47] in a developed form:
180
RF and Microwave Oscillator Design
n(t) =
冦冤
√2 ᑬ
k = +NH
∑
+
冥 冤
N k e j (k 0 + ⍀p )t + ᑬ
k=1
k = +NH
∑
−
冥
N k e j (k 0 − ⍀p )t
k=1
冧
+ ᑬ [N 0 e j ⍀t ]
(4.152)
+
where √2 N k represents the complex amplitude of the pseudosinusoid relative to the frequency k 0 + ⍀p with ⍀p << 0 , and NH is the harmonic number. In addition, m(t) is a deterministic function related to the steady state. It represents the modulation function for the corresponding noise sources. It can be expanded into a Fourier series: p = +NH
m(t) =
∑
M p e jp 0 t
with M −p = M p*
(4.153)
p = NH
The multitone case is handled with the same formalism by using multidimensional Fourier series. The global correlation matrix of all the noise sources can be expressed as: S bb = 〈 B k B k*t 〉 = MS NN M H
(4.154)
with M = ⌫m(t)⌫ −1, where ⌫ is the Fourier operator and S NN = 〈 N k N k*t 〉 . The total correlation matrix of a node voltage is: S ⌬v ⌬v = 〈 ⌬V ⌬V *t 〉 = [ J]−1 [S bb ] [ J]−H
(4.155)
[ J] = ([G] + j [⍀][C] + [Y])
(4.156)
with
[G] and [C] are the conversion matrices of the nonlinear elements; [Y] is the diagonal matrix of linear elements. [ J] is known as the conversion matrix, calculated from the Jacobian matrix. One entry of the output noise correlation matrix writes:
High-Frequency Oscillator Circuit Design
S i , j = e iT S ⌬ V ⌬ V e j = e iT J −1 MS NN M H J −H e j =
181
(4.157)
再√S NN M H J −H e i 冎H 再√S NN M H J −H e j 冎 S i , j = V iH V j
(4.158)
e i and e j are unitary vectors containing zeros everywhere except one 1 at the corresponding output port and frequency. We can clearly see that the phase or amplitude spectrum around the carrier only requires the computation of two vectors: V−1 [namely, ⌬V ( 0 − p ) ] and V1 [namely, ⌬V ( 0 + p ) ]. Each vector’s computation requires solving one linear system and calculating two matrix-vector products [109]. Thanks to iterative linear solvers, the linear system resolution can be performed very efficiently. The two matrix-vector products can also be performed efficiently due to the special structure of the two matrices M and √S NN . The conversion matrix has to be computed accurately, and this depends on the steady-state solution. We use a two-loop Newton HB method to solve the steady state—as described in [110]. Another cause that can affect the conversion matrix accuracy is the aliasing. It can be reduced by increasing the number of harmonics of the steady-state solution as well as by increasing the FFT oversampling factor in the HB algorithm. Other AM and PM noise simulation methods in the frequency domain have been proposed. They assume quasi-static approximations and obviously do not take into account the low-frequency dynamics of the oscillator circuit (e.g., the large time constants of the bias circuits that fall in the frequency range of the generation recombination or 1/f noise sources). As already stated by several authors, simulation results obtained by these methods can be very different from those obtained by the conversion matrix method. In the benchmark proposed in Appendix 4C, Figure 4C.9, one can verify that the low-frequency dynamic of the oscillator circuit is taken into account by the simulator as well as for a frequency offset near then far from carrier by varying the resonant frequency of the low-frequency filter. However, finding accurate noise results requires precise calculation of the steady state, a feat of which modern commercial simulators are capable. An inaccurate steady-state solution can lead to inaccurate phase noise results near the carrier. A misunderstanding of this numerical problem has led some to invoke a hidden specific ‘‘frequency modulation near carrier’’ to explain and correct the resulting phase-noise slope versus frequency offset
182
RF and Microwave Oscillator Design
near carrier. In fact, in a free-running oscillator the modulation laws are the same near and far from the carrier. An inaccurate phase-noise near carrier results only from an inaccurate numerical steady state solution. This problem is now solved with the advanced resolution algorithms included in modern simulators (see Appendix 4C). The major problems encountered today to obtain an accurate result of phase-noise simulation are due to inaccurate modeling of the noise sources. Their localization inside the active device models (FETs and bipolar transistors) becomes necessary to obtain accurate and reproducible results. Inadequate noise source localization can lead to a miscalculation of more than 10 dB in the final result. Failing to take into account the cyclostationary noise source can also bring a miscalculation of a few decibels. Without adequate care, the error can exceed 15 dB in either way. In conclusion, rigorous general-purpose CAD tools for nonlinear noise analysis in free-running oscillators are well-established today. Using them requires a good knowledge of active device noise sources and their electrical models. Unfortunately, current low-frequency noise models are generally very inaccurate and do not provide an exact representation of the behavior of noisy nonlinear circuits and, more specifically, of the phase-noise spectrum in free-running oscillator circuits.
4.3 Design Rules of Low Phase-Noise Free-Running Oscillators A well-designed oscillator requires optimization of the circuit behavior as follows: • At the oscillation frequency 0 (large-signal); • At the intermodulation frequencies near the carrier resulting from
the interaction between (small-signal) noise sources and (large-signal) steady state; • At low frequencies near dc, when 1/f and generation-recombination noise sources are present. This situation is illustrated in Figure 4.49. For the sake of clarity it may be better to rely on very simple but illustrative examples, as shown in Figures 4.50 and 4.51, to define the conditions required for phase-noise optimization in a free-running oscillator circuit.
High-Frequency Oscillator Circuit Design
183
Figure 4.49 Frequencies involved in oscillator noise conversion.
Figure 4.50 Representation of one-port oscillator.
Figure 4.51 Simplified representation of one-port oscillator.
Numerical simulations and thorough theoretical calculations have shown that the conditions inferred from simple examples remain valid for transistor circuits modeled with realistic libraries [111, 112]. In the following analytical calculations, the influence of the harmonic frequencies of the angular oscillation frequency 0 is neglected. They will
184
RF and Microwave Oscillator Design
obviously be taken into account when numerical simulation is undertaken, but the general conclusions remain the same. 4.3.1 Phase Noise in One-Port Oscillator Circuit The expression of the phase noise spectral density of a one-port oscillator, including a high-frequency thermal noise source, can be shown to be, in the first order [77, 113] (see Figures 4.50 and 4.51), kT
S =
P 0 Q 2ext
(4.159)
冉 冊 ⍀ 0
2
In a parallel configuration P 0 and Q ext can be replaced by:
P 0 = P tot
冉
GL GL + GR
Q ext = Q R
冊
2
(4.160)
GR GL
(4.161)
where P tot is the total power delivered from the active device. Q R is the resonator’s unloaded Q-factor. G R is the equivalent conductance of the resonator. G L is the load conductance. kT is the available white noise power spectral density. So that, S =
20 kT ⍀2P tot Q 2R
with
冉
GR GL + GR
冊
2
(4.162)
High-Frequency Oscillator Circuit Design
185
G L = G 0 N L2 G R = G u N R2 C = C u N R2 L= QR =
(4.163)
Lu N R2
0 dB u 2G u d
|
0
=
CR0 Cu0 = GR Gu
We assume that the spectral density of the noise source is independent, at the first order, of the power delivered by the active device (i.e., the noise temperature T is approximately constant). By inspection of (4.162), it follows that the optimization of phasenoise spectral density requires the maximization of the product below: P tot Q 2R
冉
GR GL + GR
冊
2
(4.164)
Maximization of P tot. The nonlinear active device provides a maximal output power, P tot , for a load conductance, G opt , which is a characteristic of the active device. In the circuit under consideration, G opt is the sum of the load and resonator conductances:
G opt = G L + G R
(4.165) GR Optimization of the load conductance. The term is clearly maximum G opt when both G L = 0 and G R = G opt . Under these conditions, N R opt can be found. Note that in a real oscillator circuit, to get some output power G L will be made smaller but not quite canceled. In addition, the intrinsic unloaded Q-factor of the resonator, denoted Q R , is fixed by the tank circuit, and must be maximum. As a first conclusion we can infer that phase-noise spectral density in a free-running oscillator circuit will be optimal under the following conditions: • When the nonlinear active element provides the maximum output
power at the oscillation frequency 0 ; • When this power is mainly dissipated in the resonator and, as shown in this example, when the energy stored at the active device port reaches its maximum [114, 115].
186
RF and Microwave Oscillator Design
First optimization conditions for low-noise operation thus appear as follows: • Optimization of the operating conditions at 0 in terms of active
device available power; • Optimization of the operating conditions around the oscillation frequency 0 in stored energy terms. Note that this energy stored in a linear parallel resonant circuit is proportional to the susceptance slope versus frequency around 0 . 4.3.2 Generalization to Transistor-Oscillator Circuits Optimization of the power at the oscillation frequency 0 . The required conditions must be calculated in terms of transistor added power. Indeed, the available power of the transistor at the oscillation frequency 0 is the maximum added power of the transistor (Figure 4.52):
P available ( 0 ) = P add max ( 0 ) = P out ( 0 ) − P in ( 0 )
(4.166)
If this added power is wholly dissipated in the resonator, the oscillator does not provide any power to the output load. Such a limit case enables us to find the minimum phase noise that we can get. In a practical application, the designer will choose the best tradeoff between a higher output power or a better phase noise.
Figure 4.52 Power location in an oscillator circuit.
High-Frequency Oscillator Circuit Design
187
In the ‘‘ideal’’ case, in which all of the added power is dissipated in the resonator, the energy stored in the resonator is maximum. In conclusion, for a chosen bias point the transistor must be matched at its maximum added power operating point in order to dissipate maximum power in the resonator of the oscillator circuit. 4.3.3 A Very Useful Design Tool: The Transistor Load-Line The basic representation of a transistor is shown in Figure 4.53. From a circuit design point of view, a transistor is fundamentally a nonlinear voltage controlled current source I out , mainly controlled by the input voltage Vcontrol . It must be pointed out that this basic diagram is valid whatever the technology used and can be applied both to field effect transistors (e.g., MESFETs, HEMTs, and MOSFETs) and to bipolar transistors (e.g., BIPs and HBTs). Again, for the sake of clarity, a linearized model will be used. The quasi-linear representation of ˜I out in Figure 4.54 allows a simple analytical
Figure 4.53 A basic transistor representation.
Figure 4.54 Linearized output voltage-controlled current source of a transistor.
188
RF and Microwave Oscillator Design
calculation of the phase shift between V˜out and V˜c in order to get the available output power of this current source. The power delivered from the source at the angular frequency is given by: 1 P out = − ᑬ (V˜ out ˜I ou* t ) 2
(4.167)
By taking the phase of V˜ out as reference V˜ out = V out , and ˜VC = VC e j c, we obtain for P out : 1 P out = − ᑬ [V out (G Mo VC e j c + G out V out )] 2
(4.168)
1 P out = − V out (G Mo VC cos c + G out V out ) 2
(4.169)
or
The condition required on C in order to get a maximum output power is given by:
c = (2k + 1)
(4.170)
When this condition is fulfilled, the load admittance of the controlled current source becomes a conductance. This condition remains valid to the first order, by neglecting harmonic frequencies, in the nonlinear case, so that, in nonlinear operation, the curve obtained by plotting the current locus 2 , in the plane I out (t ) = f (V out (t )), can be I out (t ) over one period, T0 = 0 considered as a nonlinear Lissajous plot (Figure 4.55). The resulting closed curve is called the transistor load-line. So when c = , the area delimited by the load-cycle is null. Therefore, the transistor load-line proves extremely efficient, as a visual tool, to optimize the phase shift between VC (t ) and V out (t ). 4.3.4 Finding the Maximum Added Power of the Transistor by Numerical Calculation The following simulations have to be achieved to find the maximum added power with a nonlinear model of transistor. The circuit schematic to achieve the maximum added power is illustrated in Figure 4.56.
High-Frequency Oscillator Circuit Design
189
Figure 4.55 (a) Optimum load-line and (b) nonoptimum load-line.
Figure 4.56 Determination of transistor power added by simulation software.
The procedure is given in the following steps: • The aim of this optimization is to maximize:
1 P add = − {ᑬ [V out ( 0 ) I ou* t ( 0 )] + ᑬ [V in ( 0 ) I in* ( 0 )]} 2 (4.171) with the constraints
再
V C min < V C (t ) < V C max V out min < V out (t ) < V out max
• The variables of the optimization are L and G L .
(4.172)
190
RF and Microwave Oscillator Design
• A numerical optimization is performed for different bias points and
by gradually increasing I 0 ( 0 ). For every couple (L opt , G opt ), one plots output power P out and added power P add , with the bias point as a parameter, as a function of the input power and verify that the curves are smooth (without hysteresis). For each P addmax point, one plots the corresponding transistor load-lines and checks that the plot is a closed curve with null or limited area.
• Finally, one calculates:
Y in ( 0 ) = Y load ( 0 ) =
I in ( 0 ) V in ( 0 )
(4.173)
I out ( 0 ) V out ( 0 )
(4.174)
In this way, optimal operating conditions via the transistor load-line plot are well-defined at 0 . Then these conditions can be used for oscillator circuit optimization [116–118]. 4.3.5 Optimization and Localization of the Energy Stored in the Circuit Optimizing but also locating the energy stored in the circuit must be carefully analyzed. To be convinced of the importance of the energy localization, the following theoretical oscillator circuit can be simulated (Figure 4.57). • The model of transistor is nonlinear and includes noise sources. • The two-port input and output matching circuits Q input and Q output ,
respectively, are lossless, with lumped elements (low Q). They allow the following: • To match the transistor input to the characteristic conductance G c of the feedback transmission line; • The achievement of the transistor maximum added power for the chosen bias point and oscillation frequency: 0 ; ˜ out − ∠ V˜ in = , to take • The achievement of the phase shift ∠ V the electrical length of the feedback transmission line as 1 + 2 = at 0 , for demonstration purposes; • The ‘‘ideal’’ resonator: L R , C R is tuned to 0 .
High-Frequency Oscillator Circuit Design
191
Figure 4.57 Oscillator circuit with an idealized feedback lossless circuit.
4.3.5.1 Circuit Analysis at Oscillation Frequency
The maximum added power of the transistor is split into the power dissipated in the load, P load , and the input power, P in . Since the input port of the transistor is matched to G C , the relationship between | V˜ in | and | V˜ out | is fixed: | V˜ in | = | V˜ out | . Finally, at 0 the feedback circuit appears as a phase shifter of electrical length tot = 180°. 4.3.5.2 Calculation of the Energy Stored in the Lossless Feedback Circuit
The energy stored in the lossless feedback circuit can be written as: W ( 0 ) =
冉
j ˜ dI˜ in* ˜ dV˜ in* ˜ dI˜ ou* t ˜ dV˜ ou* t V in + I in + Vout + I out 4 d d d d
冊|
0
(4.175) Let us write:
冋
d CR − d
1 LR
册
=
dB R d
|
0
(4.176)
192
RF and Microwave Oscillator Design
and as
| V˜ in | = | V˜ out |
1 W= 4
冦
冋 | 冋
(4.177)
册 册
| V˜ in | 2 G C
d T dB R 2 + cos ( T − 2 ) + d d
| ˜I in
d T dB R 2 + sin ( T − 2 ) − d d
2
G C2
GC
2 dB R sin ( T − 2 ) cos ( T − 2 ) ᑣ(V˜ in ˜I in* ) G C d
冧
(4.178)
In addition, since the input admittance of the transistor is matched to GC , ᑣ(V˜ in ˜I in* ) | 0 = 0 and
| V˜ in | 2 | ˜I in |
2
|
= 0
(4.179)
1
(4.180)
G C2
Finally, W=
| V˜ in | 2 4
冉
2G C
d T dB R + d d
冊
(4.181)
| V˜ in | is fixed by the condition on maximum added power. tot is fixed. So the stored energy is fixed and independent of the localization of the L R , C R circuit along the feedback line. We can then ask the following question: Given that the energy stored in the circuit has been fixed independently of the resonator location along the feedback transmission line, is the resulting phase noise independent of phase shift 1 between the transistor input and the resonator? The result is that the phase noise is dependent on 1 . Moreover, S is a periodic function of 1 . Minima recur over a cycle of (see Figure 4.58).
High-Frequency Oscillator Circuit Design
193
Figure 4.58 Phase noise versus length line 1 .
The difference between S max and S min can reach more than 15 dB. This variation depends directly on the value of the resonator slope susceptance dB R . d This type of curve can be obtained in experimental circuit [110, 111]. dB When R is very high, some points along the curve S = f ( 1 ) may d even happen to be numerically unstable. So, if maximizing the energy stored in an oscillator circuit is an essential condition to optimize phase noise, this is obviously not enough: A transistor is a voltage-controlled current source, the controlling voltage is taken at a diode port, forward-biased in case of BIPs and HBTs or reverse-biased in case of MESFETs and HEMTs. Because of the highly nonlinear capacitance of this input diode, the phase noise conversion chiefly takes place at this controlling voltage port. So not only must the energy stored in the resonator be at a maximum, but also its transfer to the controlling voltage port of the transistor must be maximized. The last but not least condition for the optimization of the phase noise is that no AM/PM conversion must occur. 4.3.6 AM/PM Conversion The AM/PM conversion takes place when a nonlinear conductive element is reactively loaded. In a transistor this occurs mainly at the current-source
194
RF and Microwave Oscillator Design
output port. In order to eliminate this conversion, the source I out (t ) must be resistively loaded. Fortunately, I out (t ) must be loaded by a pure conductance in order to reach the maximum added power of the transistor. So the AM/PM conversion is reduced by this requirement. Finally, the influence of 1/f or generation-recombination low-frequency noise sources has to be minimized by short-circuiting or open-circuiting these sources whenever feasible. Another way to reduce low-frequency noise conversion in transistor oscillators is to achieve a low-frequency feedback [119]. Unfortunately, for these low-frequency noise sources and the transistor, being inherently nonlinear, the mixing with the large-signal at 0 generates noise sources located on upper and lower sideband components around the carrier and cannot be short-circuited; nor can HF noise sources.
4.3.7 Conclusion Low phase-noise oscillator design initially requires optimizing the transistor nonlinear behavior at the oscillation frequency by tuning it at the maximum added power (for the chosen bias point); this can be adequately checked by means of the transistor load-line. In addition, most of the maximum added power of the transistor must be dissipated in the resonator in order to ensure maximum energy stored in the resonator. This stored energy must be brought back to the controlling input of the transistor where phase noise generation mainly takes place. Finally, the output voltage–controlled current source of the transistor must be loaded resistively in order to avoid any AM/PM conversion. In the final step of the design a last numerical simulation of PM noise must be performed to fine tune the bias point and dynamic load-line of the transistor, in order to limit the swing of the controlled-current source, and avoid the regions where the low-frequency noise sources arise. Figures 4.59–4.64 indicate some free-running oscillator configurations that yield a low phase-noise spectrum. The feedback circuits provide an adequate phase-shift of the inputoutput voltages, resulting in a phase shift between VC and V out close to , within the transistor. Figure 4.63 shows a conventional architecture of a doubling-oscillator. Note that this architecture permits the attenuation of the phase noise level due to some low-frequency noise sources of the transistor, thanks to its push-
High-Frequency Oscillator Circuit Design
195
Figure 4.59 Quarter-wave transmission line feedback oscillator.
Figure 4.60 Quarter-wave lumped feedback oscillator.
push configuration. Beyond the topologies discussed in this chapter, other configurations can be found in [120].
4.4 Practical Examples 4.4.1 Breadboard Oscillators The first example demonstrates the importance of the energy-stored localization for low phase-noise operation. A practical ‘‘breadboard’’ oscillator has
196
RF and Microwave Oscillator Design
Figure 4.61 Feedback circuit using a dielectric resonator two-port configuration.
Figure 4.62 Feedback circuit using a dielectric resonator in one-port configuration.
been built. This circuit is shown in Figure 4.65. The setup includes a universal test feature, two low-Q tuners to large signal match the transistor to 50⍀ at the maximum added power operating point. An isolator at the amplifier output eliminates spurious oscillations. A TE 01␦ dielectric resonator with a resonator quality factor of 5,000 at 9.2 GHz is coupled between two transmission lines. A 20-dB coupler provides a very small part of the oscillator power for measurements. It is important to note that two phase shifters are used to both obtain oscillation phase conditions and maximum energy transfer between resonator and transistor input.
High-Frequency Oscillator Circuit Design
Figure 4.63 A doubling oscillator using dielectric resonator.
Figure 4.64 Oscillator with a very high-Q cavity in transmission.
197
198
RF and Microwave Oscillator Design
Figure 4.65 Breadboard oscillator circuit.
Figure 4.66 shows the phase-noise spectrum at the 10-kHz offset from the carrier as a function of the phase shift between the resonator access and the voltage-controlling voltage port of the transistor, while the operating point (Paddmax ) is maintained constant. A phase-noise variation of 10 dB is obtained between the best and worst cases, following the localization of the resonator. This result validates the previous forecast. The second example concerns an ultra-low-noise oscillator. A practical example of an optimized oscillator circuit has been built (see Figure 4.67). It operates at 9.2 GHz. An isolator at the transistor output eliminates spurious oscillations. It is followed by a 20-dB coupler to measure the spectrum. The high-Q resonator (Q 0 = 105,000) is a sapphire resonator working in a WGM7 mode stabilized at 330K [121]. The transistor is a packaged 0.25 m × 200 m PHEMT chosen for its low flicker noise. The measured characteristics of the amplifier matched to 50⍀ at its maximum power added operating point are P in = 4 dBm, P out = 12 dBm, and P add = 11.3 dBm. The losses of the feedback circuit (excluding the resonator) are 3 dB. The resonator coupling coefficients are tuned to  1 = 0.5 and  2 = 1.3 for optimum operation giving 9.2-dBm cavity dissipated power. Two phase shifters allow for the adjustment of the phase shift between the resonator and the internal controlling voltage port of the transistor while
High-Frequency Oscillator Circuit Design
199
Figure 4.66 Phase noise versus length line 1 .
Figure 4.67 High-Q sapphire resonator transistor oscillator.
maintaining the previous power conditions and 9.2-GHz oscillation frequency. The noise measurements are carried out using the HP3848 phase noise setup and a reference synthesized oscillator. A phase-noise level of −80 dBc/Hz at a 100-Hz offset from carrier with a −30 dB/dec slope has been measured (see Figure 4.68). The measurement frequency range is limited by thermal fluctuations below 10 Hz and by the reference oscillator noise above 300 Hz.
200
RF and Microwave Oscillator Design
Figure 4.68 Measured phase noise spectrum of the high-Q sapphire resonator oscillator.
4.4.2 Oscillators on MMIC Technology 4.4.2.1 Main Applications
The main advantages of MMIC-based oscillators are the high operating frequency, very good repeatability, better reliability compared to hybrid solutions, and the high level of integration. All these characteristics generate a lot of new opportunities for many applications. Generally, the MMICs are used when a high volume of production is necessary; this is mainly due to cost issues. Indeed, for these applications the key factor is to avoid any tuning during the production phase. Knowing how an oscillator is critical, only MMICs can bring this advantage at microwave frequencies. A lot of applications are already using or intending to use this technology. Among them the most known are the following: • Radar applications for automotive. This is a typical market where high
volumes are considered and where low-cost solutions are necessary for all the millimeter-wave front ends. The main frequencies are 24 GHz for short-range sensors (from 0.1m to 10m) and 77 GHz for medium range detection (from 1m to 200m). These radar-based sensors contribute to security by detecting and classifying objects in order to avoid collisions.
High-Frequency Oscillator Circuit Design
201
• Communication systems. Applications such as VSAT, radio links,
interactive TV, WLAN, and optical links require relatively high quantities and MMICs are a good candidate; for these systems, very high performance of phase noise is generally required and a lot of design effort on done on state-of-the-art technologies is necessary. 4.4.2.2 Main Architectures
MMIC technology allows a lot of design possibilities, and this compensates for the relatively low quality factor (Q) of the passive devices. The selected architectures should give enough flexibility in order to apply all the rules necessary for optimizing the design like the following ones: • The general and well-known rule that is independent of the technol• •
• •
ogy is to maximize the quality factor of the resonator. The open-loop gain, which gives the level of transistor compression, has to be controlled versus the noise conversion around the carrier. The load impedance of the current source of the transistor has to be optimized according to the low-frequency noise sources of the transistor. The oscillation frequency sensitivity to the transistor nonlinear elements has to be minimized. The bias point has to be perfectly controlled. This is linked with all the mechanisms of noise conversion around the carrier.
All these design rules must be applied and controlled versus the technology spread, the temperature, and the frequency when a VCO is considered. Now we will consider some architecture examples; they are discussed in terms of one specific technology but can be applied to several. The first example can be called the ‘‘quarter-wave’’ structure (Figure 4.69). The feedback is realized by a quarter-wave transmission line from the drain to the gate; the appropriate phase is obtained by using a series resonance on the gate and a parallel resonance on the drain. This architecture is very flexible; indeed, the oscillation frequency and the transistor load impedance can be optimized separately. The resonator can be put in series on the gate (L g , C g , R g ) or in parallel on the drain (L d , C d , R d ). For a VCO design the varactor can replace the gate and/or the drain capacitor. The second example (Figure 4.70) is a ‘‘push-push like’’ structure. It uses two balanced transistors. The loop is obtained by connecting the collector of the first one to the base of the other one. This structure provides several
202
RF and Microwave Oscillator Design
Figure 4.69 FET-based ‘‘quarter-wave’’ oscillator.
Figure 4.70 HBT-based ‘‘push-push–like’’ oscillator.
well-known advantages like phase-noise reduction and easy frequency doubling. A lot of investigations are now done for evaluating their behavior at microwave frequencies. An important advantage in MMIC technology is the concept of multifunctions. For frequency generation this allows the integration on the same chip of several functions such as buffer amplifiers, multipliers, and frequency dividers. Figure 4.71 shows a generic block diagram of a multifunction MMIC chip dedicated to frequency generation. According to the application, to the architecture, and to the technology performance, the multiplier rank (N) and the divider rank (P) are adjusted. Depending on the resonator Q needed and on the flexibility to externally adjust the oscillation frequency, an external resonator can be coupled to the MMIC. 4.4.3 MMIC FET-Based Oscillator Examples The following examples have been realized on the pseudomorphic HEMT (PHEMT) process with a 0.25- m gate length. They are all multifunction
High-Frequency Oscillator Circuit Design
203
Figure 4.71 MMIC generic multifunction for frequency generation.
dedicated to automotive radar applications at 77 GHz. As direct generation at this frequency does not provide enough performance, all the oscillators are subharmonics of 77 GHz. There are mainly two kinds of VCOs used in this application: • VCO for FMCW radar. In this case the frequency modulation consists
of a linear frequency sweep versus time. Due to very critical linearity requirements, the VCO is controlled by a feedback loop. This loop can be designed for linearity and phase-noise compression. Consequently, for this architecture the VCO phase noise is not a very critical issue. A level of −60 dBc/Hz at frequency 100 kHz from the carrier at frequency 77 GHz is acceptable. • VCO for pulsed radar. In this case the modulation consists of very
fast frequency pulses, and the use of phase-locked loop (PLL) is not easily possible. As a consequence, the VCO has to be compliant with the phase-noise requirement as a free-running oscillator. A value of −70 dBc/Hz at frequency 100 kHz from the carrier at frequency 77 GHz is the minimum necessary. Whatever the described modulations, the frequency tuning range has to be about 100–400 MHz at frequency 77 GHz. 4.4.3.1 VCO Multifunction at 38.5 GHz Using an External Resonator
The first example is dedicated to pulsed radar and consists of a VCO at 12.75 GHz followed by a frequency tripler (Figure 4.72). The oscillator architecture is close to the one given on Figure 4.70. In order to obtain the phase-noise performance, an external resonator is used. It is based on microstrip coupled lines printed on soft substrate.
204
RF and Microwave Oscillator Design
Figure 4.72 MMIC block diagram of the 38.25-GHz VCO multifunction.
As PHEMT devices are well-known for their low-frequency noise limitations, an important effort has been made on the design for minimizing the phase noise. All the rules described previously have been applied. As the low-frequency noise generators have the main effect on phase noise, the key rules are the control of the transistor current source load line (see Figure 4.73 and Section 4.3.2.1) and the oscillator frequency sensitivity to the nonlinear capacitors of the transistor (Figure 4.74). The voltage and current swings are limited in order to avoid forward current on the gate to source diode (at low Vds voltage) and the breakdown region where impact ionization can also significantly affect the phase noise (at high Vds voltage). The oscillation frequency shift due to 1% variation of C gs and C gd capacitors is around 0.6 MHz; this is a key parameter used as a reference value for comparing several architectures, which is based on the theoretical explanation of 4.3.2.
Figure 4.73 Transistor current source load line of the VCO.
High-Frequency Oscillator Circuit Design
205
Figure 4.74 Oscillator frequency shift due to 1% variation of transistor nonlinear capacitors (Cgs and Cgd ).
The measured characteristic shows a frequency range of 400 MHz around 38.35 GHz (Figure 4.75). The frequency drift versus temperature is less than 200 MHz from −40°C to +100°C. The phase noise is better than −77 dBc/Hz at frequency 100 kHz from the carrier, all within the frequency range (Figure 4.76). The MMIC photograph is shown in Figure 4.77. The chip area is only 2.8 mm2 for a multifunction integrating a VCO, a frequency tripler, and two buffer amplifiers. This reduced size has been obtained due to a lot of layout effort using only lumped elements. 4.4.3.2 VCO Multifunction at 38.25 GHz Fully Integrated on MMIC
This VCO multifunction has the same architecture as the previous one (VCO at 12.75 GHz followed by a frequency tripler), but the resonator is integrated on the chip. It is based on lumped inductors and on interdigit capacitors in order to maximize the quality factor. The final Q of the oscillator is, of course, lower than the one obtained with an external resonator, and this leads to more tuning range but also to higher phase noise. However, this approach is very interesting for the final user due to a very simple and not critical integration process in the front end. This kind of oscillator fits to architectures where PLL is used. A second varactor has been introduced for providing an electronic center frequency tuning that compensates all the
206
RF and Microwave Oscillator Design
Figure 4.75 Measured frequency-tuning characteristic of the 38.25-GHz VCO coupled to an external resonator.
Figure 4.76 Measured phase noise of the 38.25-GHz VCO coupled to an external resonator.
possible production spreads. Due to the relatively low-Q oscillator and in order to obtain a phase-noise performance reaching the specifications, a very specific operating point has been chosen for minimizing the low-frequency noise generation and transposition around the carrier. The load line is presented in Figure 4.78, which shows very low drain voltage and current swings.
High-Frequency Oscillator Circuit Design
207
Figure 4.77 Photograph of the 38.25-GHz VCO coupled to an external resonator.
Figure 4.78 Transistor current source load-line of the fully integrated VCO.
The oscillator frequency sensitivity to the nonlinear transistor capacitors (C gs and C gd ) is shown in Figure 4.79, for 1% variation the shift is around 3 MHz. Assuming the same operating point (bias and load line) as for the VCO coupled to an external resonator, and considering that the low-frequency noise has the most important effect on the phase noise, the phase noise of this fully integrated structure should be around 14-dB worse than
208
RF and Microwave Oscillator Design
Figure 4.79 Oscillator frequency shift due to 1% variation of transistor nonlinear capacitors (Cgs and Cgd).
the other one. Indeed, the phase noise is proportional to the square of this sensitivity. However, due to the fact that the operating point is more optimized, the degradation will be lower. The measured characteristics are a tuning range higher than 2.5 GHz (Figure 4.80) and a phase noise better than −65 dBc/Hz at frequency 100 kHz from the carrier (Figure 4.81). The obtained phase noise is not exactly 14-dB worse than that for the previous version; this confirms the better optimization of the operating point. 4.4.3.3 Oscillator/Harmonic Mixer Multifunction at 38.25 GHz
This multifunction consists of a high-quality fixed-frequency oscillator, an LO amplifier at 19 GHz, a second-order harmonic mixer at 38.25 GHz, and an RF amplifier at 38.25 GHz (Figure 4.82). This chip is used for downconversion in the design of control loops. Due to the oscillator stability and phase-noise requirements, a coupling to an external high-Q resonator is necessary. A high dielectric constant and low-loss material are used in a well-known configuration called dielectric resonator oscillator (DRO). Due to the very high resonator Q (around 20,000 at frequency 10 GHz), and after applying the same design rules as for the previous examples, the frequency sensitivity to the nonlinear capacitors of the transistor is more than 10 times lower than the one obtained on the VCO with external resonator. Taking
High-Frequency Oscillator Circuit Design
209
Figure 4.80 Measured frequency tuning characteristic of the fully integrated 38.25-GHz VCO.
Figure 4.81 Measured phase noise of the fully integrated 38.25-GHz VCO.
210
RF and Microwave Oscillator Design
Figure 4.82 MMIC block diagram of the 38.25-GHz oscillator/harmonic mixer multifunction.
into account the phase-noise dependence on this parameter, the improvement should be higher than 20 dB compared to the VCO coupled to an external resonator. As the oscillator Q factor obtained with the dielectric resonator depends a lot on the cavity quality, the given value is just an indication. The obtained results are a very good phase noise of less than −112 dBc/Hz at frequency 100 kHz from carrier at frequency 19 GHz (Figure 4.83) and a frequency stability versus temperature better than 4ppm/°C. The MMIC photograph is shown in Figure 4.84. The chip area is only 1.8 mm2 for a multifunction integrating an oscillator, a subharmonic mixer, an LO, and RF buffer amplifiers. 4.4.4 MMIC HBT-Based Oscillator Example The following example has been realized on the GaAs HBT process with an emitter width of 2 m. The key advantage of this technology for oscillator designs is the very low level of low-frequency noise. For small devices the gain is high enough to design VCOs up to 24 GHz at fundamental frequency. An additional interesting possibility is the integration on the same chip of digital frequency dividers. Together with the push-push–based new architecture, this will be the trend for the near future. The described example is dedicated to communication applications; it is a VCO done in X-band. The architecture is the one shown in Figure 4.69. Two varactors are used; one replaces the capacitor C g and the other replaces the capacitor C d . The design procedure is the same as for the FETbased oscillators. However, due to very low level of low-frequency noise of the devices, the phase noise analysis has to take into account additional noise
High-Frequency Oscillator Circuit Design
211
Figure 4.83 Measured phase noise (given at 19 GHz) of the 38.25-GHz oscillator/harmonic mixer multifunction.
Figure 4.84 Photograph of the 38.25-GHz oscillator/harmonic mixer multifunction.
sources like the Shot noise due to collector current and all the thermal noise due to resistances. New tools are now available for this kind of simulation. Figure 4.85 gives the simulated characteristic of phase noise for center frequency band. From a 1–10-kHz offset from the carrier, the main origin is low-frequency noise and the slope is around −30 dB per decade. At 100 kHz
212
RF and Microwave Oscillator Design
Figure 4.85 Simulated phase noise of the X-band HBT-based VCO.
all the contributions are important and the slope is around −25 dB per decade. At a megahertz offset the low-frequency noise can be neglected and the slope is around −20 dB per decade. The measurements shows a frequency tuning range of more than 12% (Figure 4.86) and a phase noise of around −90 dBc/Hz at frequency 100 kHz from carrier (Figure 4.87). There is a very good agreement between simulation and measurement; this is due to accurate modeling and perfect control of operating point of the active device. Concerning phase noise and compared to P-HEMT-based VCOs, this result is an improvement of around 15 dB if the same frequency and tuning range are considered.
4.5 Conclusion Designing oscillator circuits at RF frequencies requires specific knowledge in extremely varied fields such as the following: • The physics of semiconductor devices and their specific characteriza-
tion methods in order to extract nonlinear CAD-oriented device models [122]; • Physical phenomena leading to electrical noise and the associated mathematical processing of stochastic phenomena;
High-Frequency Oscillator Circuit Design
213
Figure 4.86 Measured frequency tuning characteristic of the X-band HBT-based VCO.
Figure 4.87 Measured phase noise of the X-band HBT-based VCO.
214
RF and Microwave Oscillator Design
• The characterization method of electrical noise in order to extract
•
• • •
realistic models that accurately describe the observed phenomena that have been observed; The linear theory of electrical circuits, both invariant and timevarying, but also the nonlinear theory that causes the fundamental phenomena of bifurcation, self-oscillation, frequency division, and chaos—all liable to occur in such circuits; Numerical simulation tools specific to autonomous circuits; Experimental observation cannot be dispensed with at all, and it is, ‘‘in fine,’’ the only way to check the validity of the design; Finally, oscillator designing requires the implementation of design rules derived from theoretical and experimental bases in order to get the best chances of obtaining a good result from the first manufacturing run.
Nevertheless, designing oscillator circuits remains an art—an everdeveloping art, but an enthralling art.
References [1]
Obregon, J., et al., ‘‘Modeling and Design of Low Noise Microwave Oscillators,’’ IEEE MTT-S International Microwave Symposium, Workshop Notes in Microwave Oscillators—Looking Back and Looking Forward, Boston, MA, June 16, 2000.
[2]
Sze, S. M., Physics of Semiconductor Devices, New York: John Wiley and Sons, 1998.
[3]
Mathieu, H., Physique des Semiconducteurs et des Composants Electroniques, New York: Masson, 1998.
[4]
Ebers, J. J., and J. L. Moll, ‘‘Large Signal Behavior of Junction Transistors,’’ Proc. IRE, Vol. 42, 1954, pp. 1761–1774.
[5]
Gummel, H. K., and H. C. Poon, ‘‘An Integral Charge Control Model of Bipolar Transistor,’’ Bell System Technical Journal, Vol. 49, 1970, pp. 827–852.
[6]
Getreu, E., Modeling the Bipolar Transistor, New York: Elseiver, 1976.
[7]
Beaufoy, R., and J. Sparks, ‘‘The Junction Transistor as a Charge Control Device,’’ Automat. Tel. Eng. J., Vol. 13, 1957, p. 310.
[8]
Kroemer, H., ‘‘Theory of Wide Gap Emetter for Transistors,’’ Proc. IRE, Vol. 45, No. 11, November 1957, pp. 1153–1537.
[9]
Floriot, D., ‘‘Optimisation et mode´lisation de transistors bipolaires a` he´te´rojonction GaInP/GaAs. Application aux amplificateurs monolithiques de puissance, Band X,’’ Ph.D. thesis, Universite´ de Pierre et Marie Curie (Paris VI), Paris, 1995.
High-Frequency Oscillator Circuit Design
215
[10]
Viaud, J. P., et al., ‘‘Nonlinear RF Characterization and Modelling of Heterojunction Bipolar Transistors Under Pulsed Conditions,’’ 24th European Microwave Conference, Cannes, France, Vol. 2, September 5–8, 1994, pp. 1610–1615.
[11]
Kirk, C. T., ‘‘A Theory of Transistor Cutoff Frequency (ft) Fall-Off at High Current Density,’’ Trans. on Elect. Dev., Vol. 9, 1962, p. 164.
[12]
Fraysse, J. P., et al., ‘‘A Non-Quasi-Static Model of GaInP/GaAs HBT for Power Applications,’’ IEEE MTT-S Digest, Vol. II, 1997, pp. 379–382.
[13]
Fossum, J. G., and S. Veeraraghavan, ‘‘Partitioned-Charge-Based Modeling of Bipolar Transistors for Non-Quasi-Static Circuit Simulation,’’ IEEE Electron Device Letters, Vol. 7, No. 12, 1986, pp. 652–654.
[14]
Miller, S. L., ‘‘Avalanche Breakdown in Silicon,’’ Phys. Rev., Vol. 99, August 15, 1955, pp. 1234–1241.
[15]
Pritchard, R. L., Electrical Characteristics of Transistors, New York: McGraw-Hill, 1967.
[16]
Grossamn, P. C., ‘‘A Physically Based Large Signal HBT Model with Self Heating and Transit Time Effects,’’ IEEE MTT-S Digest, 1991, pp. 233–236.
[17]
Baureis, P., and D. Seitzer, ‘‘Parameter Extraction for HBT’s Temperature-Dependent Large Signal Equivalent Circuit Model,’’ GaAs Symposium, 1993, pp. 263–266.
[18]
Peyretaillade, T., et al., ‘‘A Pulsed-Measurement–Based Electrothermal Model of HBT with Thermal Stability Prediction Capabilities,’’ IEEE MTT-S Digest, 1997, pp. 1515–1518.
[19]
Castagne´, R., et al., Circuits Inte´gre´s en Arse´niure de Gallium, Paris: Masson et CENTENST, 1989.
[20]
Pouvil, P., Composants Semi-Conducteurs Micro-ondes, Paris: Masson, 1994.
[21]
Tajima, Y., and P. D. Miller, ‘‘Design of Broadband Power GaAs FET Amplifiers,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 30, No. 6, 1982, pp. 261–267.
[22]
Teyssier, J. P., J. P. Viaud, and R. Que´re´, ‘‘A New Nonlinear I(V) Model for FET Devices Including Breakdown Effects,’’ IEEE Microwave and Guided Wave Letters, Vol. 4 No. 4, April 1994, pp. 104–106.
[23]
Horio, K., and A. Wakabayashi, ‘‘Computer-Aided Analysis of Surface-State Effects on Kink Phenomena in GaAs MESFET’s,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 47, No. 4, 1999, pp. 516–518.
[24]
Horio, K., and Y. Fuseya, ‘‘Two-Dimensional Simulations of Drain-Current Transients in GaAs MESFET’s with Semi-Insulating Substrates Compensated by Deep Levels,’’ IEEE Trans. on Electron Devices, Vol. 41, No. 8, August 1994, pp. 1340–1346.
[25]
Kunihiro, K., and Y. Ohno, ‘‘A Large-Signal Equivalent Circuit Model for SubstrateInduced Drain-Lag Phenomena in HJETs,’’ IEEE Trans. on Electron Devices, Vol. 43, No. 9, September 1996, pp. 1336–1342.
[26]
Horio, K., and T. Yamada, ‘‘Two-Dimensional Analysis of Surface-State Effects on Turn-On Characteristics in GaAs MESFETs,’’ IEEE Trans. on Electron Devices, Vol. 46, No. 4, April 1996, pp. 648–655.
216
RF and Microwave Oscillator Design
[27]
Ouarch Z., et al., ‘‘Measurement-Based Nonlinear Electrothermal Modeling of GaAs FET with Dynamical Trapping Effects,’’ IEEE MTT-S Digest, Baltimore, MD, June 1998, pp. 599–602.
[28]
Collantes, J. M., et al., ‘‘Discrepancies Obtained in Transconductance Extracted from Pulsed I-V Curves and from Pulsed S-Parameters in HEMTs and PHEMTs,’’ Electronics Letters, February 1998, pp. 291–292.
[29]
Anholt, R., Electrical and Thermal Characterization of MESFETs, HEMTs, and HBTs, Norwood, MA: Artech House, 1994.
[30]
Laloue, A., et al., ‘‘A Measurement-Based Model of HEMT Taking into Account the Nonlinear, Nonuniform Transmission Line Nature of the Channel and Its Associated Low Frequency Noise Sources,’’ GaAs 2000 Symposium, Paris, October 2000.
[31]
Teyssier, J. P., et al., ‘‘40-GHz/150-ns Versatile Pulsed Measurement System for Microwave Transistor Isothermal Characterization,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 46, No. 12, December 1998, pp. 2043–2052.
[32]
Parker, A., et al., ‘‘Determining Timing for Isothermal Pulsed-Bias S-Parameters Measurements,’’ IEEE MTT-Symposium Digest, 1996, pp. 1707–1710.
[33]
Kirkpatrick, S., C. Gelatt, and M. Vecchi, ‘‘Optimization by Simulated Annealing,’’ Science, Vol. 220, No. 4598, May 1993, pp. 498–516. Raoux, J. J., ‘‘Mode´lisation des transistors a` effet de champ microond: Du mode`le analytique au mode`le tabulaire parame`trique,’’ Ph. D. thesis, Universite´ de Limoges, France, No. 9-95, September 1995.
[34]
[35]
Sakyrai, T., B. Lin, and A. R. Newton, ‘‘Fast Simulated Diffusion: An Optimization Algorithm for Multiminimum Problems and Its Applications to MOSFET Model Parameter Extraction,’’ IEEE Trans. on Computer-Aided Design, Vol. 11, No. 3, 1992, pp. 228–234.
[36]
Wei, C. J., and J. C. M. Hwang, ‘‘Direct Extraction of Equivalent Circuit Parameters for Heterojunction Bipolar Transistors,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 43, No. 9, September 1995, pp. 2035–2039.
[37]
McIntosh, P. M., and C. M. Snowden, ‘‘Measurement of Heterojunction Bipolar Transistor Thermal Resistance Based on a Pulsed I-V System,’’ Electronics Letters, January 1997, pp. 100–101. Dambrine, G., et al., ‘‘A New Method for Determining the FET Small-Signal Equivalent Circuit,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 36, No. 7, July 1998, pp. 1151–1159. Portilla, J., et al., ‘‘A New Coherent Extraction Method of FETs and HEMTS Models for MMIC Applications,’’ GaAs Symposium, Torino, Italy, April 1994. Mallet-Guy, B., et al., ‘‘Direct Extraction of a Distributed Nonlinear FET Model from Pulsed I-V/Pulsed S-Parameter Measurements,’’ Microwave and Guided Wave Letters, Vol. 8, No. 2, February 1998, pp. 102–104. Laloue, A., et al., ‘‘A Measurement Based Distributed Low Frequency Noise HEMT Model: Application to Design of Millimiter-Wave Automotive Radar Chip Sets,’’ IEEE MTT-S International Microwave Symposium, Phoenix, AZ, May 20–25, 2001, pp. 423–426.
[38]
[39] [40]
[41]
High-Frequency Oscillator Circuit Design
217
[42]
van der Ziel, A., and E. R. Chenette, ‘‘Noise in Solid-State Devices,’’ in Advances in Electronics and Electron Physics, L. Marton and C. Marton (eds.), New York: Academic Press, Vol. 46, 1978.
[43]
Van Vliet, C. M., ‘‘Macroscopic and Microscopic Methods for Noise in Devices,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 41, No. 11, November 1994.
[44]
Chovet, A., and P. Viktorovitch, ‘‘Bruit electrique: Aspects physiques (2e´me partie),’’ L’onde ´electrique, Vol. 57, No. 12, 1977, pp. 773–783.
[45]
Hooge, F. N., T. G. M. Kleinpenning, and L. J. K. Vandamme, ‘‘Experimental on 1/f Noise,’’ Rep. Prog. Phys., Vol. 44, 1981.
[46]
Nougier, J. P. (ed.), III-V Microelectronics, New York: North-Holland, 1991.
[47]
Dragone, C., ‘‘Analysis of Thermal and Shot Noise in Pumped Resistive Diodes,’’ Bell System Technical Journal, November 1968.
[48]
Kerr, A. R., ‘‘Noise and Loss in Balanced and Subharmonically Pumped Mixers: Part I Theory,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. MTT-27, No. 12, December 1979, pp. 938–943.
[49]
Cappy, A., et al., ‘‘Noise in Devices Under Nonlinear Operation,’’ Solid-State Electronics, Vol. 43, 1999.
[50]
Bonani, F., et al., ‘‘A TCAD Approach to the Physics-Based Modeling of Frequency Conversion and Noise in Semiconductor Devices Under Large Signal Forced Operation,’’ IEEE Trans. on Electron Devices, Vol. ED-48, No. 5, May 2001, pp. 966–977.
[51]
Pe´rez, S., S. L. Delage, J. Obregon, ‘‘Microscopic Analysis of Generation-Recombination Noise in Semiconductors Under dc and Time-Varying Electric Fields,’’ Journal of Applied Physics, Vol. 88, No. 2, July 15, 2000, pp. 800–807.
[52]
Perez, S., et al., ‘‘Monte Carlo Analysis of the Influence of DC Conditions on the Upconversion of Generation-Recombination Noise in Semiconductors,’’ Revue Semiconductor Science and Technology, IOP Publishing Limited, U.K., No. 16, 2001, pp. L8–L11.
[53]
Van der Ziel, A., Noise in Solid-State Devices and Circuits, New York: John Wiley and Sons, 1986.
[54]
Fish, P. J., Electronic Noise and Low Noise Design, Basingstoke, England: Macmillan, 1993.
[55]
Vignaud, P., ‘‘Me´trologie et e´tude du bruit de fond des transistors a` effet de champ AsGa MESFET et MODFET. Bruits de la grille, du canal et corre´lation,’’ Ph.D. thesis, Montpellier, France, May 1990.
[56]
Barros, C., et al., ‘‘Experimental Techniques for Very Low Noise Measurements,’’ International Workshop on Noise and Reliability of Semiconductor Devices, Brno, Czech Republic, Proc. of the International NODITO Workshop, 1995, pp. 45–51.
[57]
Vildeuil, J. C., M. Valenza, and D. Rigaud, ‘‘Low Frequency Noise in Gate and Drain of PHEMTs and Related Correlation,’’ Microelectronics Reliability, Vol. 40, No. 11, 2000, pp. 1915–1920.
[58]
Benabdesselam, M., ‘‘Bruit et corre´lation dans les transistors MOS en re´gime de multiplication,’’ Ph.D. thesis, Montpellier, France, 1991.
218
[59]
[60]
[61]
[62]
[63] [64]
[65] [66]
[67] [68] [69] [70]
[71]
[72] [73] [74]
[75]
RF and Microwave Oscillator Design
Rigaud, D., and M. Valenza, ‘‘Correlation Measurement of Carrier Multiplication Noise Sources in MOS Transistors at Low Frequencies,’’ IEEE Trans. on Electron Devices, Special Issue, Vol. 41, No. 11, November 1994, pp. 2076–2081. Vildeuil, J. C., ‘‘Caracte´risation et mode´lisation basse fre´quence de transistors PHEMT AlGaAs/InGaAs/GaAs: bruits du canal, de la grille et corre´lation,’’ Ph.D. thesis, Montpellier, France, 2000. Jarrix, S., et. al., ‘‘Noise Correlation Measurements in Bipolar Transistors. I. Theoretical Expressions and Extrated Current Spectral Densities,’’ J. Appl. Phys., Vol. 81, No. 6, 1997, pp. 2651–2657. Delseny, C., et al., ‘‘Noise Correlation Measurements in Bipolar Transistors. Correlation Between Base and Collector Currents,’’ J. Appl. Phys., Vol. 81, No. 6, 1997, pp. 2658–2664. Mourier, Y., ‘‘Caracte´risation et bruit de fond de transistors bipolaires,’’ Ph.D. thesis, Montpellier, France, 1998. Vandamme, L. K. J., ‘‘Noise as a Diagnostic Tool for Quality and Reliability of Electronic Devices,’’ IEEE Trans. on Electron Devices, Special Issue, Vol. 41, No. 11, 1994, pp. 2176–2187. Berthier, P., ‘‘Transistors a` effet de champ AlInAs/(Al)GaInAs(P) pour photode´tection inte´gre´e a`1,3-1,55 m,’’ Ph.D. thesis, Montpellier, France, 1993. Berthier, P., et al., ‘‘InGaAsP Channel HFETs on InP for OEIC Applications,’’ Journal of Lightwave Technology IEEE Optical Society of America (OSA), Vol. 12, No. 12, 1994, pp. 2131–2138. Vandamme, L. K., et al., ‘‘Gate Current 1/f Noise in GaAs MESFET,’’ IEEE Trans. on Electron Devices, Vol. 35, No. 7, 1988, pp.1071–1075. Peransin, J. M., et al., ‘‘Bias Dependence of Low Frequency. Gate Current Noise in GaAs MESFETs,’’ Electronics Letters, Vol. 25, No. 7, March 1989, pp. 439–440. Pe´ransin, J. M., et al., ‘‘1/f Noise in MODFETs at Low Drain Bias,’’ IEEE Trans. on Electron Devices, Vol. 37, No. 10, 1990. Vandamme, L., J. M. Peransin, and D. Rigaud, ‘‘Coherence Between Gate and Drain Fluctuations in MESFETs and MODFETs Biased in the Ohmic Region,’’ IEEE Trans. on Electron Devices, Vol. 39, No. 10, 1992, pp. 2377–2382. Rhayem, J., et al., ‘‘1/f Noise Investigations in Small Channel Length Amorphous Silicon Thin Film Transistors,’’ Journal of Applied Physics, Vol. 83, No. 7, 1998, pp. 3660–3667. Rhayem, J., et al., ‘‘1/f Noise in Thin Film Transistors: Effect of Scaling Down,’’ Solid-State Electronics, Vol. 43, 1999, pp. 713–721. Rhayem, J., et al., ‘‘1/f Noise Modeling in Long Channel Amorphous Silicon Thin Film Transistors,’’ Journal of Applied Physics, Vol. 87, No. 3, 2000. Das, M. B., ‘‘High-Frequency Performance Limitation of Millimeter-Wave Heterojunction Bipolar Transistor,’’ IEEE Trans. on Electron Devices, Vol. 35, May 1988, pp. 604–614. Plana, R., B. van Haaren, and L. Escotte, ‘‘Excess Noise Reduction in GaInp/GaAs Heterojunction Bipolar Transistor,’’ IEEE Trans. on Electron Devices, Vol. 18, No. 3, March 1997.
High-Frequency Oscillator Circuit Design
219
[76]
Laloue, A., ‘‘Mode´lisation non line´aire distribue´e des transistors a` effet de champ: application a` l’analyse de la stabilite´ des transistors et des caracte´ristiques en bruit dans les circuits MMIC millime´triques,’’ Ph.D. thesis, Universite´ de Limoges, France, No. 15, 2001.
[77]
Kurokawa, K., ‘‘Nonlinear Microwave Oscillators,’’ Proc. IEEE, Vol. 61, No. 10, 1973.
[78]
Bolcato, P., et al., ‘‘Efficient Algorithm for Steady-State Stability Analysis of Large Analog/RF Circuits,’’ Proc. IEEE MTT-S Digest, Phoenix, AZ, May 20–25, 2001, pp. 451–454.
[79]
Bode, H. W., Networks Analysis and Feedback in Amplifier Design, New York: Van Nostrand, 1945.
[80]
Platzker, A., and W. Struble, ‘‘A Rigorous Yet Simple Method for Determining Stability of Linear N-Ports Networks,’’ GaAs IC Symp. Digest, 1993, pp. 251–254.
[81]
Mons, S., et al., ‘‘A Unified Approach for the Linear and Nonlinear Stability Analysis of Microwave Circuits Using Commercially Available Tools,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 47, No. 12, 1999, pp. 2403–2409.
[82]
Kundert, K. S., ‘‘Introduction to RF Simulation and Its Application,’’ IEEE Journal of Solid-State Circuits, Vol. 34, No. 9, 1999, pp. 1298–1319.
[83]
Freund, R. W., G. H. Golub, and N. M. Nachtigal, ‘‘Iterative Solution of Linear Systems,’’ Acta Numerica, 1992, pp. 57–100.
[84]
Troyanovsky, B., ‘‘Frequency Domain Algorithms for Simulating Large Signal Distortion in Semiconductor Devices,’’ Ph.D. thesis, Stanford University, 1997.
[85]
Gayral, M., et al., ‘‘The Spectral Balance: A General Method for the Analysis of Nonlinear Microwave Driven by Nonharmonically Related Generators,’’ Proc. IEEE. MTT-S Digest, 1987, pp. 119–121.
[86]
Rizzoli, V., and A. Neri, ‘‘ State-of-the-Art Present Trends in Nonlinear Microwave CAD Techniques,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 36, 1988, pp. 343–365.
[87]
Maas, S. A., Nonlinear Microwave Circuits, Norwood, MA: Artech House, 1988.
[88]
Paillot, J. M., et al., ‘‘A General Program for the Steady-State, Stability and FM Noise Analysis of Microwave Oscillators,’’ Proc. IEEE MTT-S Digest, Dallas, TX, 1990, pp. 1287–1290.
[89]
Gilmore, R. J., and M. B. Steer, ‘‘Nonlinear Circuit Analysis Using the Method of Harmonic Balance—A Review of the Art: Part I, Introductory Concepts,’’ International Journal of Microwave and Millimeter-Wave Computer-Aided Engineering, Vol. 1, No. 1, 1991, pp. 22–37.
[90]
Gilmore, R. J., and M. B. Steer, ‘‘Nonlinear Circuit Analysis Using the Method of Harmonic Balance—A Review of the Art: Part II, Advanced Concepts,’’ International Journal of Microwave and Millimeter-Wave Computer-Aided Engineering, Vol. 1, No. 2, 1991, pp. 159–180.
[91]
Que´re´, R., et al., ‘‘Large-Signal Design of Broad-Band Monolithic Microwave Frequency Divider and Phase-Locked Oscillators,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 41, 1993, pp. 1928–1938.
220
[92] [93]
[94]
[95]
[96]
[97]
[98] [99] [100] [101]
[102] [103] [104] [105]
[106] [107] [108]
RF and Microwave Oscillator Design
Odyniec, M., ‘‘Nonlinear Oscillators Theory and Design,’’ IEEE MTT-S, Workshop on Recent Advances in Oscillator Design, Orlando, FL, 1995. Sancho, S., and A. Suarez, ‘‘Nonlinear Analysis of Microwave Frequency Synthesizers: Stability and Incidental FM,’’ Proc. IEEE MTT-S Digest, Boston, MA, June 11–16, 2000, pp. 497–500. Rizzoli, V., and A. Lipparini, ‘‘General Stability Analysis of Periodic Steady State Regimes in Nonlinear Microwave Circuits,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 33, No. 1, 1985, pp. 30–37. Rizzoli, V., A. Neri, and D. Masotti, ‘‘Local Stability Analysis of Microwave Oscillators Based on Nyquist’s Theorem,’’ IEEE Microwave and Guided Wave Letters, Vol. 7, No. 10, 1997, pp. 341–343. Mees, A. I., and L. O. Chua, ‘‘The Hopf Bifurcation Theorem and Its Application to Nonlinear Oscillations in Circuits and Systems,’’ IEEE Trans. on Circuits and Systems, Vol. CAS-26, No. 8, 1983. Campovecchio, M., et al., ‘‘Stability Analysis of Millimetre-Wave Circuits. Application to DC-40 GHz PHEMT Amplifier and Ku-Band HBT Power Amplifier,’’ 30th European Microwave Conference, invited paper, focused section, Vol. 2, Paris, 2000, pp. 294–297. Que´re´, R., et al., ‘‘Linear and Nonlinear Stability Analysis of MMICs,’’ GaAs Symp. Dig., Paris, France, June 5–7, 1996, paper 7INV1. Jugo, J., et al. ‘‘Closed-Loop Stability Analysis of Microwave Amplifiers,’’ IEE Electronics Letters, Vol. 37, No. 4, 2001, pp. 226–228. Demir, A., ‘‘Analysis and Simulations of Noise in Nonlinear Electronic Circuits and Systems,’’ Ph.D. thesis, University of California, Berkeley, 1997. Rutman, J., ‘‘Characterization of Phase and Frequency Instabilities in Precision Frequency Sources: Fifteen Years Progress,’’ Proc. IEEE, Vol. 66, No. 9, 1978, pp. 1048–1075. Lax, M., ‘‘Classical Noise. V. Noise in Self-Sustained Oscillators,’’ Physical Review, Vol. 160, No. 2, 1967, pp. 290–307. Kuva¨s, R. L., ‘‘Noise in Single-Frequency Oscillators and Amplifiers,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 21, No. 3, 1973, pp. 127–134. Bolcato, P., and R. Poujois, ‘‘A New Approach of Noise Simulation in Transient Analysis,’’ Proc. ISCAS, 1992, pp. 887–890. Siweris, H., and B. Schiek, ‘‘Analysis of Noise Upconversion in Microwave FET Oscillators,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 33, No. 3, 1985, pp. 233–242. Penfield, P., ‘‘Circuit Theory of Periodically Driven Nonlinear Systems,’’ Proc. IEEE, Vol. 54, No. 2, 1966, pp. 266–280. Haus, H. A., and R. B. Adler, ‘‘Invariants of Linear Noisy Networks,’’ I.R.E., Convention Record Part 2, 1956, pp. 53–67. Ferre-Pikal, E. S., et al., ‘‘Draft Revision of IEEE STD 1139-1988 Standard Definitions of Physical Quantities for Fundamental Frequency and Time Metrology— Random Instabilities,’’ Proc. IEEE International Frequency Control Symposium, May 28–30, 1997, pp. 338–357.
High-Frequency Oscillator Circuit Design
221
[109]
Bolcato, P., et al., ‘‘A Unified Approach of PM Noise Calculation in Large RF Multitone Autonomous Circuit,’’ Proc. IEEE MTT-S Digest, Boston, MA, June 11–16, 2000, pp. 417–420.
[110]
Ngoya, E., et al., ‘‘Steady-State Analysis of Free or Forced Oscillators by Harmonic Balance and Stability Investigation of Periodic and Quasiperiodic Regimes,’’ Intl. J. Microwave and Millimeter-Wave Computer-Aided Engineering, Vol. 5, No. 3, 1995, pp. 210–223.
[111]
Nallatamby, J. -C., et al., ‘‘Low Phase Noise Operation of Microwave Oscillator Circuits,’’ IEEE Trans. on Ultrasonics, Ferroelectrics, and Frequency Control, Vol. 47, No. 2, 2000, pp. 411–420.
[112]
Prigent, M., et al., ‘‘An Efficient Design Method of Ultra Low Noise Microwave Oscillators Circuit,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 47, No. 7, 1999, pp. 1122–1125.
[113]
Edson, W. A., ‘‘Noise in Oscillators,’’ Proc. IRE, Vol. 48, 1960, pp. 1454–1466.
[114]
Goldstein, L., ‘‘Frequency Stabilization of Microwave Oscillators,’’ IRE E.D., Vol. 1, 1954, pp. 30–40.
[115]
Shelton, E. J., ‘‘Stabilization of Microwave Oscillators,’’ IRE Trans. Electron Devices, Vol. 1, 1954, pp. 30–40.
[116]
Portilla, J., et al., ‘‘Osciladores HEMT monoliticos en banda Ku controlados por tension,’’ Proc. of URSI Symposium, Bilbao, Spain, 1997, pp. 553–556.
[117]
Portilla, J., et al., ‘‘Low Noise Monolithic Ku Band VCO Using Pseudomorphic HEMT Technology,’’ IEEE Microwave Guided Wave Letters, Vol. 7, November 1997, pp. 380–382.
[118]
Boudiaf, A., M. Ahdjoudj, and P. Bouvil, ‘‘Low-Phase Noise PHEMT-Based MMIC VCOs for LMDS Applications,’’ Proc. IEEE MTT-S Digest, Phoenix, AZ, May 20–25, 2001, pp. 1562–1566.
[119]
Prigent, M., and J. Obregon, ‘‘Phase Noise in FET Oscillators by Low Frequency Loading and Feedback Circuitry Optimization,’’ IEEE Trans. on Microwave Theory and Techniques, Vol. 35, No. 3, 1987, pp. 349–352.
[120]
Khanna, A. P. S., ‘‘GaAs MESFET Circuit Design,’’ Ch. 7, in GaAs MESFET Circuit Design, R. Soares (ed.), Norwood, MA: Artech House, 1988.
[121]
Giordano, V., et al., ‘‘High-Q SiO2 Whispering Gallery Mode Resonator,’’ Proc. IEEE International Frequency Control Symposium, April 13–16, 1999, pp. 593–596.
[122]
Hooge, F. N., ‘‘1/f Noise Sources,’’ IEEE Trans. on Electron Devices, Special Issue, Vol. 41, No. 11, 1994, pp. 1926–1935.
Appendix 4A: HBT and HEMT Nonlinear Models This appendix summarizes the nonlinear functions of the models of HBT and HEMT, with a table gathering all the fitting parameters
222
RF and Microwave Oscillator Design
4A.1 HBT Model 4A.1.1 Nonlinear Current Sources and Gain T SC T
I R = I SC 0 e
T SE T
I F = I SE 0 e
I FC = I SFC 0 e
I FE = I SFE 0 e
冉 冉 冉 冉
T SFC T
T SFE T
I CT = I F − I R
e
e
V BC C UT
V BE E UT
e
e
冊 冊
−1 −1
V BC fC U T
V BE fE U T
冊 冊
−1 −1
F = 0e
1 T
Table 4A.1 Parameters of HBT Corrective Model I SE0
E
TSE
465
1.09
18,549 0.26
I SFE0
fE
TSFE
C
1.98
11,160 1.9 × 10−25 1.09
I SC0
TSC
I SFC0 fC
0
19
1.97
T SFC
0
1
R
Tamb ⴗC
R th ⴗC/W
C th
9393
3.45
728
1
295
200
5 × 10−9
4A.1.2 Base-Emitter Capacitances and Transcapacitance • Junction capacitance: C jE (V BE ) =
冉
C jE 0
V 1 − BE ⌽E
• Diffusion capacitance: C dE (V BE ) = C BEd 0 e
冊
m jE
C BEd1 T
e
V BE D UT
• Transcapacitance: C dEC (V BC ) = C BEc 0 C BEc 1 e C BEc1VBC
High-Frequency Oscillator Circuit Design
223
Table 4A.2 Parameters of the HBT Base-Emitter Capacitances and Transcapacitance C jE 0
⌽E
C BEd 0
C BEd 1
D
C BEc 0
C BEc1
Tamb
3 × 10−13
1.8
10−7
18,549
1.09
5 × 10−31
40
295
4A.1.3 Base-Collector Capacitances and Transcapacitance • Junction capacitance: C jC (V BC ) =
C jC 0
冉
1−
V BC ⌽C
冊
m jC
V BC
• Diffusion capacitance: C dC (V BC ) = C BCd 0 e BC U T • Transcapacitance: C dCE (V BE ) = C BCEe 0 e
C BCe1 V BE T BE U T
e
Table 4A.3 Parameters of the HBT Base-Collector Capacitances and Transcapacitance C jC 0
⌽C
C BCd 0
BC
C BCe 0
C BCd 1
BE
Tamb
2.5 × 10−13
1.2
1.25 × 10−28
1.09
2.5 × 10−8
18,549
1.09
295
4A.1.4 Extrinsic Elements Table 4A.4 HBT Extrinsic Elements L B (pH)
L C (pH)
L E (pH)
R B (⍀)
R C (⍀)
R E (⍀)
C pb (pF)
C pc (pF)
81
83
6.23
3.3
0.68
1.59
0.253
0.084
4A.2 HEMT Nonlinear Model This is the same model used in the oscillator benchmark given with the book. 4A.2.1 I DS Current Source:
if V GSN > 0.0 then I DST a = I DSS × f g × f d then I DST a = 0
224
RF and Microwave Oscillator Design
with V GSN = 1 +
V DSN = V DSP
V GS (t − ) − V VP V DS V (t − ) 1 + w GS VP
冉
冊
V P = V P 0 + pV DS + V fg =
冉
1 1 V GSN − (1 − e −mV GSN ) m 1 1 − (1 − e −m ) m
冊
2
f d = (1 − e −V DSN (1 + aV DSN + bV DSN ) ) correct_ gm = 1 +  gm × (V DS − V dm ) × (1 + tanh (␣ gm (V GS (t − ) − V gm ))) I DS = I DST a × correct_ gm Table 4A.5 Parameters of the PHEMT I DS Current Source V DSP
V
a
b
m
P
I DSS
0.5865
2.971
0.9854
0
32.57
6.172 × 10−2
0.8337
 gm
␣ gm
w
V dm
(pS)
V gm
V P0
0.1088
0.2732
1.113
26.86
0.257
4.555
0.4958
4A.2.2 Gate-Drain Diode
冉
I GD = I GDS e
V GD gd U T
−1
冊
High-Frequency Oscillator Circuit Design
225
Table 4A.6 Parameters of the I GD Current Source I GDS
gd
5.966 × 10−12
1.912
4A.2.3 Gate-Source Diode
冉
I GS = I GSS e
V GS gs U T
冊
−1
Table 4A.7 Parameters of the PHEMT I GS Current Source I GSS
gs
9.939 × 10−11
2.1832
4A.2.4 Gate-Drain Capacitance
C GD (V GD ) = Cg 0d
冉
V′ 1 − eff V bd
冊冉 n′
冊
1 1 (V GD − V td ) − (V GD − V bd ) + C bd 2d 1′ 2d 2′
with V ef′f =
V + V bd 1 (d ′ − d 2′ ) + td 2 1 2
d 1′ =
√(V GD − V td )
2
+ d ′2
d 2′ =
√(V GD − V bd )
+ d ′2
2
Table 4A.8 Parameters of the PHEMT Gate-Drain Capacitance Cg 0d
V bd
1.354 × 10−14 1.887
V td
d′
C bd
n′
−0.5914
0.2543
3.371 × 10−14 7.842
226
RF and Microwave Oscillator Design
4A.2.5 Gate-Source Capacitance
C GS (V GS ) = Cg 0s
冉
V eff 1− V bs
冊冉 n
冊
1 1 (V GS − V ts ) − (V − V bs ) + C bs 2d 1 2d 2 GS
with V eff =
1 V + V bs (d − d 2 ) + ts 2 1 2
d1 =
√(V GS − V ts )
2
+ d2
d2 =
√(V GS − V bs )
+ d2
2
Table 4A.9 Parameters of the PHEMT Gate-Source Capacitance Cg 0s
V bs
18.85 × 10−14 1.176
V ts
d
C bs
n
−0.7791
−0.1419
0
−0.1086
4A.2.6 Extrinsic Elements Table 4A.10 PHEMT Extrinsic Elements L G (pH)
L D (pH)
L S (pH)
R G (⍀)
R D (⍀)
R S (⍀)
C pg (fF)
C pd (fF)
30.85
16.5
16.35
1.95
2.575
2.575
48.98
20.5
R i (⍀)
R GD (⍀)
C DS (fF)
0.366
15.65
56.5
Appendix 4B: Transistor Low-Frequency Noise Characterization 4B.1 Equivalent Circuit for Noise Calculations From Figure 4B.1, the equivalent circuit of the intrinsic transistor is given in Figure 4B.2 and the admittance matrix { y int } is directly obtained.
High-Frequency Oscillator Circuit Design
227
Figure 4B.1 Noise equivalent circuit for simultaneous input-output noise measurements.
Figure 4B.2 Equivalent circuit of the intrinsic transistor.
In order to take into account the parasitic access resistances the impedance matrix of this intrinsic part is calculated. We have, respectively: {Y int } =
再
{ Z int } =
再
y1 + y3
−y 3
g m − y3
y2 + y3
冎
(4B.1)
冎
(4B.2)
and z2 + z3
z3
z3 −
z1 + z3
with (for n = 1, 2, 3) zn =
1 y det { y int } n
(4B.3)
and
=
g m int det { y int }
(4B.4)
228
RF and Microwave Oscillator Design
So we have the following equivalent circuit (see Figure 4B.3). Now the same transformation is done with the associated noise sources. For the intrinsic transistor the steps of the calculation are summarized in Figures 4B.4–4B.6.
Figure 4B.3 T representation of the intrinsic transistor.
Figure 4B.4 Circuit transformations for noise calculations.
Figure 4B.5 Circuit transformations for noise calculations.
Figure 4B.6 Circuit transformations for noise calculations.
High-Frequency Oscillator Circuit Design
229
And we obtain in complex notations: J 1 = i gs − i gd
(4B.5a)
J 2 = i ch int + i gd
(4B.5b)
and
再冎 v1
v2
= { Z int }
再冎 i 1′ i 2′
(4B.6)
with: i 1′ = i 1 + J 1 i 2′ = i 2 + J 2 So we have: v 1 − (z 2 + z 3 ) J 1 − z 3 J 2 = (z 2 + z 3 ) i 1 + z 3 i 2
(4B.7)
v 2 − (z 3 − k ) J 1 − (z 1 + z 3 ) J 2 = (− + z 3 ) i 1 + (z 1 + z 3 ) i 2 Let us put: E 1 = (z 2 + z 3 ) J 1 + z 3 J 2
(4B.8)
E 2 = (z 3 − ) J 1 + (z 1 + z 3 ) J 2 the equivalent circuit of the intrinsic part is given in Figure 4B.7. This representation is advantageously used to obtain the amplifier output signal. Now the parasitic access resistances and their associated noise
Figure 4B.7 Equivalent noise circuit in the T representation.
230
RF and Microwave Oscillator Design
generators are introduced. From Figures 4B.1 and 4B.7 the total noise representation is given in Figures 4B.8 and 4B.9 with: eg = R G iR G es = R S iR S
(4B.9)
ed = R D iR D The following relations are used: { Z ext } =
再
Z 11
Z 12
Z 21
Z 22
冎 再 =
z2 + z3 + RG + RS z3 − k + RS
z3 + RS
v 1 − E 1 − e g − e s = Z 11 i 1 + Z 12 i 2 v 2 − E 2 − e d − e s = Z 21 i 1 + Z 22 i 2
Figure 4B.8 Noise representation of the real transistor.
Figure 4B.9 Noise representation of the real transistor.
冎
z1 + z3 + RS + RD (4B.10) (4B.11)
High-Frequency Oscillator Circuit Design
231
⑀ 1 = E1 + eg + es
(4B.12)
⑀ 2 = E2 + ed + es 4B.2 Noise Current Calculation at the Input of the Transimpedance Amplifier Figure 4B.10 gives the equivalent form of the circuit presented in Figure 4B.1. To compute the input noise current i E′ of the transimpedance amplifier the part at the right-hand of the dotted line b ′b ″ is replaced by a Thevenin generator (e eq , R eq ) with: e eq =
ep R E − eA R P RP + RE
R eq =
RP RE RP + RE
(4B.13)
As shown elsewhere [119], the following experimental conditions apply: R E ≥ 1M⍀; R p < 100⍀. So we have: e eq ≈ e p − e A
Rp RE
R eq ≈ R p
(4B.14)
and V 2 = e eq − R p i 2
(4B.15)
From (4B.11), (4B.12), and (4B.15) we have: i2 =
e eq − ⑀ 2 − Z 21 i 1 R P + Z 22
v1 = ⑀ 1 +
(4B.16)
冉
冊
Z 12 Z Z (e ′ − ⑀ 2 ) + Z 11 − 12 21 i 1 Z 22 + R P eq Z 22 + R P
Figure 4B.10 Equivalent representation of the noise measurement setup of Figure 4B.1.
232
RF and Microwave Oscillator Design
Let us put e ′ = ⑀1 +
Z 12 (e − ⑀ 2 ) Z 22 + R P eq
Z E′ = Z 11 −
(4B.17)
Z 12 Z 21 Z 22 + R P
(4B.18)
we have: v 1 = e ′ + Z E′ i 1
(4B.19)
So Figure 4B.8 can be reduced to the circuit given in Figure 4B.9 and iE′ = iA′
e′ Z E′ + ′ ′ ′ Z E + R E Z E + R E′
(4B.20)
The experimental condition R E′ << Z E′ applies and iE′ ≈ iA′ +
e′ Z E′
(4B.21a)
and the spectral density given by the analyzer is: S VS′ ( f ) = | k ′ | S i E′ ( f ) 2
= |k ′|
2
再
S iA′ ( f ) +
− 2R.P.
再再
1
| Z E′ | 2
冎
冋
S ⑀1 ( f ) +
|
Z 12 Z 22 + R P
冎 |
|
2
Z 12 Z 12 S ⑀ 1⑀ 2 ( f ) + Z 22 + R P Z 22 + R P
S ⑀2 ( f )
|
2
册冎
S eq ( f )
(4B.21b) 4B.3 Noise Voltage Calculation at the Input of the Voltage Amplifier We determine now the Thevenin generator seen at the input of this amplifier. The Norton generator {i A′ , R E′ } is first given as a Thevenin one (e A′ , R E′ ) with:
High-Frequency Oscillator Circuit Design
233
Figure 4B.11 Circuit transformation for noise calculations.
e A′ = R E′ i A′ ; v 1 = e A′ − R E′ i 1
(4B.22)
Taking into account (4B.11) and (4B.12), we have: i1 =
e A′ − ⑀ 1 − Z 12 i 2 R E′ + Z 11
(4B.23)
So we obtain: v2 = ⑀ 2 +
冉
冊
Z 21 Z Z (e A′ − ⑀ 1 ) + Z 22 − 12 21 i 2 (4B.24) ′ Z 11 + R E Z 11 + R E′
or: v2 = e + Z S i2
(4B.25)
with: e = ⑀2 +
Z 21 (e A′ − ⑀ 1 ) Z 11 + R E′
and
Z S = Z 22 −
Z 12 Z 21 Z 11 + R E′
The experimental setup is now equivalent to the circuit given in Figure 4B.12 with e s′ =
ep Z S + R p e ZS + Rp
and
Z ′S =
ZS RP ZS + RP
(4B.26)
The voltage V E at the input of the amplifier is then: vE =
RE (e A + e s′ ) R E + Z ′S
(4B.27)
234
RF and Microwave Oscillator Design
Figure 4B.12 Equivalent circuit of the experimental setup at the input of the voltage amplifier.
The following experimental condition must be satisfied: R E >> Z ′S and v E = e A + e s′ = e A +
ZS RP ep + e ZS + RP ZS + RP
(4B.28a)
and the spectral density given by the analyzer is: S VS ( f ) = | k | S VE ( f ) 2
= |k |
再 +
2
再
S ⑀2 ( f ) +
|
|
ZS S eA ( f ) + ZS + RP
|
Z 21 Z 11 + R E′
Z 21 Z 11 + R E′
|
2
| 冎
2
|
2
冎
|
| 冊
RP S ep ( f ) + | k | ZS + RP
S ⑀ 1 ( f ) − 2RP
2
再冉
S eA′ ( f )
2
冎
Z 21 (S ⑀*1 ⑀ 2 ( f )) Z 11 + R E′
(4B.28b)
4B.4 Calculation of the Cross-Spectrum It must be noticed that for the used dynamic signal analyzer (HP 89410A) the measured cross-spectrum of the two channels A and B is related to the synthetic form: (channel A)(channel B)*
High-Frequency Oscillator Circuit Design
235
So the measured cross-spectrum is calculated with the help of (4B.21) and (4B.28) as: S V S VS′ ( f ) = (kV E (k ′iE′ )*)( f S V S VS′ ( f ) =
再
(4B.29a)
)
冉
冊 冎
kk ′*R P Z 21 Z 12 * − S ⑀1 ( f ) S ⑀2 ( f ) Z 22 + R P Z E′ * (Z S + R P ) Z 11 + R E′ ′ + S ⑀ 1⑀ 2 ( f ) +
(Z 22
Z *12 Z 21 S ⑀* ⑀ ( f ) + R P )* (Z 11 + R E′ ) 1 2
(4B.29b)
Appendix 4C: Numerical Simulations of an Oscillator Benchmark Table 4C.1 Oscillator Element Values L chock1
L chock2
C dec1
C dec2
V gs0
V ds0
L in
R load
10 nH
5 nH
10 pF
5 pF
−0.4 V
3.0 V
12 nH
50 ⍀
Lr
Rr
Cr
9.3 pH
1e 3 ⍀
26 pF
N1
N2
N3
N4
N5
N6
1
6.4
6.18
1
1.37
1
Numerical values: See Section 4A.2. Note: Harmonic frequencies higher than nine are short-circuited across the intrinsic input and output port of the transistor. 4C.1 Small Signal (AC) Open-Loop Simulation The transistor is linearized around its bias point. The transconductance is now controlled by an external independent voltage source: E ext ( ).
236
RF and Microwave Oscillator Design
The complex open-loop gain is defined as: ˜ ol = G
Vgs E ext
|
(4C.1)
where Vgs is taken across the gate capacitance. See Figures 4C.1 through 4C.4. 4C.2 Negative Conductance Concept The input admittance is calculated by introducing an external sinusoidal current I 0 ( ) (AC) across the extrinsic transistor input port. 4C.3 Steady-State Simulation The steady-state simulation is performed after elimination of the spurious frequency. Figures 4C.5 and 4C.6 show the linear admittance seen at the input port versus frequency and the oscillator load cycle.
Figure 4C.1 Simulated oscillator circuit.
High-Frequency Oscillator Circuit Design
237
Figure 4C.2 Nonlinear PHEMT model.
4C.4 Phase-Noise Simulation K Power spectral density: S ␦ i 1/f = f Z c /c : Short circuit for harmonic frequencies higher than 9. Table 4C.2 Oscillator Element Values K
L lf
R plf
C lf
4e-09
20 H
0.1⍀
0.5 F
Figure 4C.7 shows the noisy transistor used for the simulation of the oscillator phase noise (Figure 4C.8) for two unloaded quality factor values. The low-frequency filter across the intrinsic output port of the transistor is activated. 4C.5 Relation Between Steady-State Accuracy and Phase-Noise Results Figure 4C.9 shows the influence of a low-frequency circuit on the phase noise simulation. Accurate phase-noise calculation is directly related to the
238
RF and Microwave Oscillator Design
Figure 4C.3 Simulated linear open-loop circuit.
large steady-state accuracy (Figure 4C.10). It is only a numerical problem that is easily solved by increasing oversampling of the steady-state simulation.
Acknowledgments Many special thanks go to R. Que´re´, M. Valenza, and J. C. Vildeuil for a number of helpful technical discussions, support, and constructive suggestions. Our warmest thanks go to M. Delagnes for his painstaking care in correcting our English and for spending his valuable time. It is a pleasure to thank Mrs. M. C. Lerouge and Mrs. H. Rivie`re for the countless hours they devoted to solving logistic problems.
High-Frequency Oscillator Circuit Design
239
Figure 4C.4 Numerical results of open-loop gain G˜ ol ( ) versus frequency: (a) 450–550 MHz and (b) 10.14–10.36 GHz. (Note: There are two possible oscillation start frequencies.)
Our colleagues at IRCOM and many others throughout the industry deserve our deep gratitude for their valuable advice and technical discussions. It is a pleasure to recognize the stimulation of our past Ph.D. students for their searching questions and enthusiasm. We also wish to acknowledge the support of the French research center: CNRS and of the universities of Limoges and Montpellier for many of the results included in this chapter. The sponsorship of CEE, RNRT, CNES, and DGA was gratefully appreciated. Finally, J. C. Nallatamby, J. Obregon, and M. Prigent would like to thank Agathe, Denise, Maı¨lys, Pierrette, Soizic, Sylvain, and The´o for their support, patience, and encouragement.
240
Figure 4C.4 (Continued.)
RF and Microwave Oscillator Design
High-Frequency Oscillator Circuit Design
241
Figure 4C.5 (a) Linear admittance seen at the input port versus frequency: 450–550 MHz, and (b) linear admittance seen at the input port versus frequency: 10.21–10.27 GHz.
242
RF and Microwave Oscillator Design
Figure 4C.6 Oscillator load-line (see Section 4.3.2.1).
Figure 4C.7 P-HEMT transistor with 1/f noise source, thermal noise sources (Tamb ) and low-frequency filter.
High-Frequency Oscillator Circuit Design
243
Figure 4C.8 Simulated phase noise for two unloaded Qs and without low-frequency filter.
Figure 4C.9 Influence of low-frequency dynamic on phase noise (see Section 4.2.4.3).
244
RF and Microwave Oscillator Design
Figure 4C.10 Curve (1): accurate result of phase noise; and curve (2) and curve (3): inaccurate result of phase noise near the carrier due to an inaccurate steady-state analysis (see Section 4.2.4.3).
5 Modern Harmonic-Balance Techniques for Oscillator Analysis and Optimization Vittorio Rizzoli, Andrea Neri, Alessandra Costanzo, and Franco Mastri 5.1 Introduction This chapter discusses the analysis and design of autonomous (self-oscillating) nonlinear circuits making use of the harmonic-balance (HB) principle. Attention is focused on the piecewise HB technique based on the decomposition of the nonlinear circuit into a linear and a nonlinear multiport subnetwork interconnected through a number of common ports [1]. It is noteworthy that this approach—historically the first HB method proposed in the technical literature [2]—is better suited than the nodal HB approach proposed much later [3] for truly general-purpose applications encompassing the RF as well as the microwave and millimeter-wave ranges. Indeed, the piecewise technique represents the only possible choice in all those cases where the voltage concept is only significant on a local basis but becomes physically meaningless on a global basis, so that a common reference node and a consistent set of node voltages do not exist. Possible examples are a system composed of a number of integrated circuits coupled by electromagnetic fields (e.g., a beam-forming network [4]), or even a high-clock-rate integrated circuit where electromagnetic propagation in the ground plane is not negligible. In all cases, the piecewise HB method describes the linear subnetwork as a multiport in the 245
246
RF and Microwave Oscillator Design
frequency domain, so that the interaction of the nonlinear devices with the embedding circuit always takes place through a limited number of local ports [1], irrespective of how the passive circuit as a whole is analyzed—from elementary lumped circuit theory to electromagnetic simulation. Starting from this viewpoint, the chapter develops a self-consistent set of analysis and design algorithms for self-oscillating circuits explicitly devised for generality and computational efficiency—from elementary single-device topologies up to entire front ends for heterodyne communication systems, including the (single or multiple) local oscillator function.
5.2 HB Analysis of Autonomous Quasi-Periodic Regimes in Nonlinear Circuits This section discusses the basic HB techniques for autonomous circuit analysis. Most numerical approaches to the analysis of autonomous nonlinear circuits are normally restricted to the time-periodic oscillator case. This limitation is very reductive, since some of the most interesting and practically important applications of nonlinear circuits involve multitone autonomous operation, typical examples being represented by RF front ends for telecommunications systems. In this section we introduce an HB approach to the treatment of autonomous quasi-periodic regimes in nonlinear microwave circuits, which is fully compatible with the needs of a general-purpose microwave CAD environment. We use a rigorous and absolutely general piecewise HB formulation, whereby the problem is reduced to a well-posed nonlinear algebraic system to be solved by a specialized (mixed-mode ) Newton iteration. This allows the simultaneous determination of the steady-state harmonics and of the unknown fundamental frequencies of the quasi-periodic regime. Unrivaled speed and robustness are guaranteed by a general algorithm for the exact computation of the Jacobian matrix. Section 5.2.1 is devoted to a formal definition of autonomous multitone regimes. Section 5.2.2 introduces the fundamental analysis algorithms that will be systematically used throughout the chapter. Section 5.2.3 provides a preliminary treatment of the degenerate solution problem. 5.2.1 Autonomous Quasi-Periodic Regimes This section introduces the autonomy concept for general quasi-periodic regimes. Let us consider a nonlinear microwave circuit operating in a quasiperiodic electrical regime generated by the intermodulation of F timeperiodic signals of incommensurable fundamental angular frequencies i . Any signal a (t ) supported by the circuit may be represented in the form
Modern Harmonic-Balance Techniques for Oscillator Analysis
247
冣
(5.1)
a (t ) =
∑
k∈S
∑
A k exp ( j ⍀ k t ) =
k∈S
冢
F
A k exp j ∑ k i i t i=1
where ⍀ k is a generic intermodulation (IM) product of the fundamentals— that is, F
⍀k =
∑ ki i
(5.2)
i=1
In (5.1) and (5.2), k i is an integer harmonic number and k is the F-vector of harmonic numbers k1
k=
冤冥 k2
...
(5.3)
kF
The vector k spans a finite subset S of the k-space (containing the origin), which will be conventionally named the signal spectrum. The Fourier coefficient A k will be named the harmonic of a (t ) at ⍀ k [or the kth harmonic of a (t )]. Since we want to deal with real signals, S must be symmetrical with respect to the origin, and A −k = A k*. We shall also denote by S + the subset of S such that ⍀ k ≥ 0 for k ∈ S +. In general, the circuit will be excited by dc (bias) sources for which k = 0, and by a number of free periodic generators of frequencies ⍀ b (h) (1 ≤ h ≤ B ) where b (h ) ∈ S +. Let us consider the excitation matrix B = [b(1) | b(2) | . . . | b(B )]
(5.4)
of dimensions F × B. We define the rank of B, namely, R , as the maximum size of the nonsingular square submatrixes of B (R ≤ F ), and introduce the following definitions: 1. If R = F, the electrical regime is nonautonomous or completely forced. 2. If R < F, the circuit is autonomous of order M = F − R , or M-autonomous. The physical explanation of these definitions is as follows. First of all, for an autonomous regime of order M , we can always define a new set of
248
RF and Microwave Oscillator Design
fundamentals that are linear combinations (with rational coefficients) of the original ones, in such a way that M rows, say, the first M ones, of the excitation matrix (5.4) become zero. We shall assume henceforward that the i ’s have been selected in this way. In such conditions, the first M of the i ’s will be referred to as the free fundamentals. If we now introduce the quantities zi = i t
(5.5)
(1 ≤ i ≤ F ) the generic signal (5.1) takes on the form a (t ) =
冢
F
∑ A k exp j ∑ k i z i
k∈S
i=1
冣
(5.6)
and may thus be viewed as a function defined on an F -dimensional normalized time space Z, which is 2 -periodic in each dimension z i . The meaning of an autonomy of order M is now clear: The electrical regime has no forcing term (other than dc), and thus no phase reference, in M dimensions (out of F ) of the normalized time space. As a consequence, the phase of the electrical regime with respect to z i is indeterminate for 1 ≤ i ≤ M . Each arbitrary choice of the phase in the i th dimension corresponds to one of an ∞M family of equivalent electrical regimes having the same amplitude spectrum, as shown by (5.6). For M = F = 1, this implies the well-known invariance of the time-domain waveforms with respect to a shift of the time origin. 5.2.2 The Mixed-Mode Newton Iteration Throughout this chapter we shall assume that the nonlinear subnetwork may be described by a set of generalized parametric equations of the form [1]
冋 冋
册 册
v(t ) = u x(t ),
d nx dx , . . . , n , x D (t ) dt dt
i(t ) = w x(t ),
d nx dx , . . . , n , x D (t ) dt dt
(5.7)
where v(t ) and i(t ) are vectors of voltages and currents at the common ports, x(t ) is a vector of state variables (SV), and x D (t ) is a vector of time-
Modern Harmonic-Balance Techniques for Oscillator Analysis
249
delayed state variables [i.e., x Di (t ) = x i (t − i ), i = constant]; u and w are vector-valued memoryless nonlinear functions of their arguments. Note that (5.7) is equivalent to a set of implicit integro-differential equations relating voltages and currents at the device ports and is general enough to accommodate the vast majority of nonlinear device models of common use. However, some kinds of models such as spatially distributed nonlinear models described by partial differential equations, may not fall directly within the reach of (5.7) and may require some sort of approximation (such as the well-known ‘‘slicing’’ technique) for the methods discussed in this chapter to apply. The linear subnetwork has the usual frequency-domain representation Y( j )V( ) + I( ) + N( ) = 0
(5.8)
where V( ) and I( ) are vectors of voltage and current phasors; Y( j ) is the linear subnetwork admittance matrix; and N( ) is a vector of Norton equivalent current sources at the linear subnetwork ports. The set of complex HB errors at a generic IM product ⍀ k (k ∈ S + ) has the expression E k = Y( j ⍀ k )U k + W k + N(⍀ k )
(5.9)
where U k and W k are vectors of kth harmonics of u(t ) and w(t ). All vectors in (5.7)–(5.9) have a same size n d equal to the number of interconnection ports (device ports ). To avoid the use of negative frequencies, the nonlinear solving system is formulated in terms of vectors E and X H of real and imaginary parts of the HB errors (5.9) and of the SV harmonics, respectively. The size of these vectors is N T = n d (2N + 1), where N is the number of positive IM products to be taken into account in the analysis. To allow the existence of M-autonomous electrical regimes with prescribed free fundamentals, the circuit should make available M-independent degrees of freedom under the form of tuning parameters, which usually represent bias voltages and/or free parameters of the linear subnetwork. The solving system is thus written in the form E(X H , T, V ) = 0
(5.10)
where T and V are the M-vectors of the tuning parameters and of the free fundamentals, respectively. If T and V are treated as unknowns, (5.10) is apparently a nonlinear system of N T real equations in N T + 2M real unknowns. However, as it was shown in the previous section, the phases of the electrical regime with respect to the free fundamentals are not determined
250
RF and Microwave Oscillator Design
by (5.10), and may thus be arbitrarily selected. In the following this will be accomplished by setting to zero the phases of M selected SV-harmonics at M intermodulation products representing linearly independent combinations of the free fundamentals (reference harmonics ). In the harmonic state vector X H the real parts of the reference harmonics are replaced by their magnitudes and the imaginary parts are suppressed, thus generating a reduced state vector X that will be used throughout the chapter for autonomous HB analysis. The vector X only contains N T − M real quantities to be determined, and (5.10) is thus replaced by the system of N T equations in N T + M unknowns E(X, T, V ) = 0
(5.11)
Two kinds of situations are most often encountered in practice: 1. V is fixed and X, T must be determined (tuning problem ). 2. T is fixed and X, V must be determined (analysis problem ). Both cases result in well-posed nonlinear systems of N T real equations in as many unknowns. Each system can be solved by a norm-reducing Newton iteration [5], with a set of unknowns simultaneously including the reduced state vector and the tuning parameters or the free fundamentals. Because of this hybrid set of unknowns, this will be referred to as a mixedmode Newton iteration as opposed to the purely harmonic Newton used for nonautonomous circuits [1]. Of course, mixed problems where M elements of T ∪ V are fixed and the remaining M must be found, may also occur and can be solved in a similar way. For an efficient implementation of the Newton algorithm, it is of paramount importance that the Jacobian matrix of the HB errors with respect to the unknowns be computed exactly, rather than by numerical perturbations [1]. This simultaneously reduces the Jacobian evaluation cost and the number of Newton iterations required to solve (5.11), due to the increased accuracy of the derivatives. From (5.9) for k, s ∈ S + we get ∂W k ∂U k ∂E k = Y( j ⍀ k ) + ∂ Re [X s ] ∂ Re [X s ] ∂ Re [X s ] ∂W k ∂U k ∂E k = Y( j ⍀ k ) + ∂ Im [X s ] ∂ Im [X s ] ∂ Im [X s ] ∂N(⍀ k ) ∂E k ∂Y( j ⍀ k ) = Uk + ∂T ∂T ∂T
冋
∂Y( j ) ∂N( ) ∂E k = ki Uk + ∂ i ∂ ∂
册|
= ⍀k
(5.12)
+ Y( j ⍀ k )
∂U k ∂W k + ∂ i ∂ i
Modern Harmonic-Balance Techniques for Oscillator Analysis
251
The derivatives of Y and N with respect to both circuit parameters and frequency can be computed by adjoint-network techniques. The derivatives of the voltage and currents harmonics U k and W k are found in the following way [1]. We first introduce the Fourier expansions ∂u = ∂y m
p ∈ Sd
∑
C m , p exp ( j ⍀ p t )
∂u = ∂x D
∑
p ∈ Sd
C p exp ( j ⍀ p t )
∂w = ∂y m
p ∈ Sd
∑
D m , p exp ( j ⍀ p t )
∂w = ∂x D
∑
D p exp ( j ⍀ p t )
p ∈ Sd
D
(5.13)
D
where y 0 = x, y m = d mx /dt m (1 ≤ m ≤ n ), and S d is named the derivatives spectrum. S d is usually larger than the signal spectrum in order to make available all the harmonics that are required for the subsequent calculations. Note that (5.13) is real, so that C m , −p = C m* , p and the like. The derivatives of U k and W k with respect to the real and imaginary parts of the SV harmonics are expressed by [1] ∂U k = ∂ Re [X s ] ∂U k = ∂ Im [X s ] ∂W k = ∂ Re [X s ] ∂W k = ∂ Im [X s ]
n
∑ ( j ⍀ s )m[Fm , k − s + (−1)m Fm , k + s ]
m=0 n
∑ j ( j ⍀ s )m[Fm , k − s − (−1)m Fm , k + s ]
(5.14)
m=0 n
∑ ( j ⍀ s )m[G m , k − s + (−1)m G m , k + s ]
m=0 n
∑ j ( j ⍀ s )m[G m , k − s − (−1)m G m , k + s ]
m=0
where the F’s and G’s are simple linear combinations of the Fourier coefficients of (5.13): D
Fm , k − s = C m , k − s + ␦ 0m C k − s exp (−j ⍀ s TD ) D
G m , k − s = D m , k − s + ␦ 0m D k − s exp (−j ⍀ s TD )
(5.15)
252
RF and Microwave Oscillator Design
In (5.15) ␦ is Kronecker’s symbol and TD is the diagonal matrix of the time delays. By definition, the amplitude of a generic reference harmonic, say, X R , is one of the entries of X, while its phase ⌽R is arbitrarily fixed. For this case we have ∂U k ∂U k ∂U k + sin ⌽R = cos ⌽R ∂ Re [X ] ∂ Im [X R ] ∂|XR | R
(5.16)
∂W k ∂W k ∂W k + sin ⌽R = cos ⌽R ∂ Re [X ] ∂ Im [X R ] ∂|XR | R Finally, the derivatives with respect to the free fundamentals are given by [6] n
∂U s =j ∑m ∂ i m=1
冤∑
k∈S
冤∑ ∑ 冤∑ 冤∑
−j
k∈S
k∈S
−j
k∈S
D
冥 冥 冥 冥
k i Cs − k TD exp (−j ⍀ k TD )X k
n
∂W s =j m ∂ i m=1
k i ( j ⍀ k )m − 1C m , s − k X k
k i ( j ⍀ k )m − 1D m , s − k X k D
(5.17)
k i Ds − k TD exp (−j ⍀ k TD )X k
The computation of the derivatives of Y usually represents a major contribution to the overall analysis cost. In particular, finding ∂Y /∂ is more expensive than finding ∂Y /∂T, since the former involves all the reactive circuit components, and the latter only those belonging to the tuning parameters. Thus, in general tuning is a faster process than analysis. Much more so if all the tuning parameters are bias voltages, since in this case the third of (5.12) reduces to ∂E k 0 ∂N(0) = ␦k ∂T ∂T
(5.18)
The admittance then remains constant throughout the iteration and its derivatives are not required. These facts can be effectively exploited in
Modern Harmonic-Balance Techniques for Oscillator Analysis
253
many important applications, such as the computation of the frequencyvoltage characteristic of VCOs [6]. Multitone autonomous problems can be treated by the mixed-mode Newton iteration introduced in this section in a most efficient way. This method is considerably faster than the continuation method with artificial embedding [7], because it directly leads to the solution with just one Newton loop, without requiring the generation of a solution path in the state space. To avoid the degenerate (nonoscillatory) solutions of (5.11), a suitable starting point for the Newton algorithm can always be found in a straightforward way by carrying out a preliminary quasi-Newton iteration, as discussed in Section 5.2.3. Alternatively, the analysis may be carried out by the substitution algorithm, which will be discussed in Section 5.4.2. Note that in many cases the initial-point problem does not exist, since the multitone analysis can be started from the results of an oscillator optimization (see Section 5.4). Generally speaking, the pattern of possible solutions of the system (5.11) may be extremely complicated, especially for M > 1. A general solution may require a global stability analysis of the parameterized circuit based on the principles of bifurcation analysis, as discussed in Section 5.3. 5.2.3 Degenerate Solutions and Their Suppression Let us consider a nonlinear circuit for which the HB system (5.11) admits a one-autonomous solution (X ss , T, V ), where X ss is the steady-state reduced state vector, T is the only tuning parameter, and V ≡ 1 . We can partition X ss in the following way:
冋 册 (1)
X ss =
X ss
(R )
(5.19)
X ss
(1)
where X ss contains the magnitude of the reference harmonic and the real and imaginary parts of the steady-state harmonics for which the harmonic vector (5.3) has the form k1
冤冥 0
k=
... 0
(k 1 ≠ 0)
(5.20)
254
RF and Microwave Oscillator Design
Since the fundamental frequency 1 is autonomous, by definition the circuit does not contain any free sources at 1 nor at any of its harmonics. As an immediate consequence, the system (5.11) always admits at least one further solution of the form X ss =
冋 册 0
(R )
(5.21)
X ss
that will be called a degenerate solution. From a physical viewpoint, the electrical regime described by (5.21) simply consists of the circuit response to the free sources (both dc and time-periodic) exciting the circuit. On the other hand, the electrical regime described by (5.19) consists of such responses superimposed on the free oscillation of fundamental frequency 1 . If the circuit only contains dc sources, a degenerate solution will also be called a dc or stationary solution or a bias point. The degenerate solution concept can be extended to the case M > 1 in an obvious way. If the system (5.11) is solved by a mixed-mode Newton iteration, whether or not the iteration will converge to an oscillatory regime depends on the choice of the initial values of X, T, and 1 , namely, X in , Tin , and in . It is thus clear that a systematic treatment of the oscillator analysis and tuning problems by the HB technique requires that a straightforward (and possibly cheap) procedure for finding such initial values be established. This result is pursued in this section. For the sake of formal simplicity, the discussion will be restricted to the oneautonomous case (V ≡ 1 ). Let us consider the analysis problem first (fixed T, unknown 1 ). Reasonable starting values in and X in can be found in a straightforward way under very general conditions by the following algorithm. The degenerate solution (5.21) is first determined by ordinary HB analysis for forced circuits. The steady state is then perturbed by introducing in the circuit a sinusoidal current source of frequency in with an impressed current of suitable amplitude, connected in parallel to the load branch. When in is far away from the autonomous frequency of oscillation 1 , the circuit response to the perturbing source is also small and results in the appearance of a small load voltage component at frequency in , proportional to the source amplitude. On the other hand, when in falls within the locking bandwidth of the free oscillation, the oscillation is locked and the output voltage at in is close to the free oscillating value. Thus, by sweeping in across a suitable range, a fast increase of the output voltage at in is observed as in approaches 1 . The state associated with the voltage peak can be safely chosen as a starting point for the mixed-mode Newton iteration.
Modern Harmonic-Balance Techniques for Oscillator Analysis
255
A less general but computationally faster algorithm can be used when the only free generators contained in the circuit are bias sources. In this case we may find the bias point and draw a Nyquist stability plot by ordinary linear circuit analysis (see Section 5.3.4). For ≥ 0, Nyquist’s plot crosses the real axis at (at least) one point at the left of the origin of the complex plane. The associated frequency value is chosen as in . To find an acceptable X in , the amplitude of the reference harmonic is then fixed to some relatively large value V in , usually on the order of the corresponding bias voltage, and the objective function F OB = || E(X, T, in ) ||
(5.22)
(where || • || denotes the Euclidean norm) is minimized with respect to the remaining entries of X by means of a standard optimization algorithm, such as a quasi-Newton method. In this procedure, all harmonics are started from zero except for the one being held fixed. The purpose of this calculation is not to reach the harmonic balance (which would be impossible), but just to move the state vector closer to the oscillatory solution in the state space. Experience shows (see example in Section 5.2.4) that a small number of iterations (usually on the order of 20) are sufficient to reach a point X in from which the mixed-mode Newton iteration can be safely started. The process is very cheap when the problem size (i.e., the number of scalar unknowns) is small-to-moderate: As an example, for the circuit of Figure 5.4 (27 unknowns with N = 4), the generation of X in in 20 iterations typically requires 0.05 CPU seconds on a 800-MHz PC. For large circuits such as entire front ends (many thousands of unknowns) carrying out a quasi-Newton iteration may be impractical (as is the use of continuation methods), because each iteration may be extremely expensive—so that their number must be minimized. In such cases, the alternative algorithm discussed in Section 5.6.3 may be preferable. The case of a tuning problem is easier to handle, because the frequency of oscillation is assigned. In this case a suitable initial state vector X in may be simply arrived at by minimizing (5.22) by the same procedure discussed above starting from a ‘‘typical’’ value of the tuning parameter, such as 50⍀ for a characteristic impedance or /4 at in for a transmission line length. As a final point, it is worth mentioning that the HB system (5.11) may be modified in a number of ways so that any degenerate solutions will be a priori suppressed. As an example, two of the HB equations may be replaced with the Kurokawa conditions for oscillation [8]. Another possibility is to modify (5.11) as follows:
256
RF and Microwave Oscillator Design
E(X, T, V )
|| X (1) ||
=0
(5.23)
where X (1) contains the real and imaginary parts of the SV harmonics for which the harmonic vector (5.3) takes on the form (5.20). The left-hand side of (5.23) approaches a nonzero limit as the oscillation tends to vanish (i.e., as X (1) → 0), so that the algorithm used to solve (5.23) is prevented from approaching a degenerate solution. Note, however, that these techniques normally do not improve the convergence of the Newton iteration, so that the above discussed search for a suitable starting point still remains necessary. For this reason, (5.23) will not be normally used in the rest of the chapter. 5.2.4 Applications To illustrate the analysis of a quasi-periodic steady-state regime by the mixedmode Newton iteration, we consider a self-oscillating mixer whose schematic topology is given in Figure 5.1. The circuit consists of a reflection-type DRO using a 150- m FET as the active device. The nominal LO and radio frequencies are 8 GHz and 8.51 GHz, respectively. The required capacitive source feedback and inductive gate feedback are realized by an open stub and a loaded microstrip line coupled to a dielectric resonator, respectively. The same line is also used to input the RF signal. At the output, a lumped IF filter/matching circuit is fed through another microstrip line whose purpose is
Figure 5.1 Schematic topology of a dielectric-resonator tuned self-oscillating mixer.
Modern Harmonic-Balance Techniques for Oscillator Analysis
257
to provide the optimum load reactance to the FET drain at the LO frequency. In turn, the IF matching circuit is designed in such a way as to load the FET drain by a real impedance of about 150⍀ at the nominal intermediate frequency of 510 MHz. Note that for the sake of the present example the circuit topology is regarded as a priori known. In reality, it is obtained by optimizing the LO alone (i.e., after suppressing the IF section lying beyond point L in Figure 5.1) for maximum drain current at a fundamental frequency of 8 GHz by the techniques discussed in Section 5.4, with eight harmonics taken into account. The circuit is first analyzed in the absence of RF signal (M = 1, F = 1) by the methods discussed in this section, and the drain voltage spectrum shown in Figure 5.2 is obtained. The observed frequency shift with respect to the nominal LO frequency is about +675 kHz, and is due to the small additional reactive loading of the FET drain introduced by the IF filter. An RF signal with available power −10 dBm at 8.51 GHz is then injected into the gate through the input microstrip, and the circuit is analyzed once again with M = 1 and F = 2, starting from the results of the previous step. The resulting drain voltage spectrum is shown in Figure 5.3. The additional LO frequency shift due to the injection of the RF signal is about −8 kHz. The transducer conversion gain of the self-oscillating mixer is about −3 dB without RF input matching. Because of the superlinear rate
Figure 5.2 Drain voltage spectrum of the local oscillator in the absence of RF signal.
258
RF and Microwave Oscillator Design
Figure 5.3 Drain voltage spectrum of the self-oscillating mixer for an available RF input power of −10 dBm.
of convergence of the Newton iteration in the vicinity of the solution, finding the frequency of oscillation with very high accuracy requires a limited numerical effort. In both cases the unknown frequency is determined with a relative error smaller than 10−9, which requires 12 and 9 Newton iterations, respectively. This allows an excellent numerical control of the small frequency shifts that are typical of dielectric-resonator tuned oscillators and selfoscillating mixers. On an 800-MHz PC, the analysis of Figure 5.2 takes about 0.3 CPU second, 58% of which is spent for linear subnetwork computations. In turn, the multitone analysis of Figure 5.3 takes about 1.4 seconds, 65% of which is spent for linear subnetwork computations. It is thus clear that the nonlinear analysis algorithm is extremely efficient. For comparison, a time-domain analysis would be at least two orders of magnitude slower due to the high Q of the dielectric resonator (around 2,700 in the present case). To examine more in depth the degenerate solution problem, we now investigate the convergence properties of the mixed-mode Newton iteration as a function of the starting point for the VCO circuit shown in Figure 5.4. The reference harmonic is chosen as the fundamental component of the FET drain voltage. Figure 5.5 shows the boundary of the region of convergence of the Newton iteration in the (V in , f in ) plane when the analysis is carried out
Modern Harmonic-Balance Techniques for Oscillator Analysis
Figure 5.4 Schematic topology of a VCO.
Figure 5.5 Region of convergence of the Newton iteration for the VCO.
259
260
RF and Microwave Oscillator Design
by performing all the steps of the algorithms discussed in Section 5.2.3 ( f in = in /2 ). For reference, the exact frequency of oscillation f 1 = 1 /2 , the lowest value of f in obtained from the Nyquist analysis, the value determined by the method of the injected current, and the drain bias voltage V DS 0 (see Figure 5.4) are also reported in Figure 5.5. By letting V in = V DS 0 , the desired result is achieved without trials, since the initial values actually used by the algorithm lie well within the region of convergence. As a matter of fact, the tolerance of the analysis procedure with respect to the initial values is loose, since convergence is obtained for 0.83 f 0 ≤ f in ≤ 1.3 f 0 , and for 0.75 V DS 0 ≤ V in ≤ 1.33 V DS 0 in any combination. Qualitatively similar results and an equally reliable behavior of the analysis algorithm were obtained for several different oscillator topologies. It is thus clear that the method proposed in Section 5.2.3 offers consistent advantages over other approaches, which require either the generation of a solution path [7], or a considerable number of initial trials [8].
5.3 Synchronous and Asynchronous Stability This section discusses the numerical implementation of the fundamental principles of bifurcation theory in conjunction with HB-based nonlinear analysis algorithms, as a general-purpose tool for the synchronous and asynchronous stability analysis of nonlinear circuits. Section 5.4 shows that the bifurcation theory can be used not only as an analysis tool for determining the stability properties of a known circuit but also as a support to optimization techniques for including stability constraints among the design goals. The stability analysis methods discussed in this section are applicable to all the circuit topologies that fall within the reach of the HB technique. This is much more general than the classic dynamic analysis based on time-domain methods [9], which is normally limited to very low-order nonlinearities. In exchange for this, the frequency-domain description of the linear subnetwork limits the available waveforms to quasi-periodic regimes, which in turn allows only the fundamental bifurcations to be detected in this way. Some complex aspects of nonlinear circuit dynamics, especially those involving continuous spectra such as chaos, cannot be exactly described by HB. The important point, however, is that with few exceptions the methods discussed in this section are normally sufficient for ordinary engineering
Modern Harmonic-Balance Techniques for Oscillator Analysis
261
purposes, and thus represent a precious complement to the ordinary HB CAD environment. Section 5.3.1 discusses the representation of solution paths in the state space (i.e., loci of steady states having similar spectra) for a parameterized nonlinear circuit. It is shown that HB-based analysis techniques are best suited for producing neat nonredundant descriptions, especially in the case of autonomous circuits for which the steady states are not uniquely defined. Section 5.3.1 also introduces a generalized continuation algorithm for the automatic construction of solution paths in the state space. Section 5.3.2 discusses the determination of the natural frequencies of quasi-periodic steady states, which provides the basic numerical tool for the stability analysis of general nonlinear circuits operating in steady-state conditions. The generation of Nyquist stability plots for time-periodic steady states is developed as a local stability analysis tool in Section 5.3.3. Both forced and autonomous states are considered for the sake of clarity, and the autonomy-related peculiarities are examined in detail. Section 5.3.4 pursues global stability analysis by searching known solution paths for the fundamental bifurcations. A peculiar feature of HB is that unlike time-domain analysis of nonlinear circuits, this method allows the determination of unstable steady states, which is of great help in the interpretation of complex stability patterns through bifurcation analysis. Section 5.3.5 uses the methods discussed earlier to solve a few elementary stability problems. Finally, Section 5.3.6 specifically addresses the important and difficult problem of spurious generation in oscillators as a relevant application example of the proposed methodology. 5.3.1 Solution Paths in a Harmonic Phasor Space 5.3.1.1 State-Space Representation
According to the discussion developed in Section 5.2, after a suitable finite spectrum of N positive frequencies plus dc has been defined, the real timedependent state vector x(t ) may be replaced by the vector X H of real and imaginary parts of the SV harmonics. The circuit states may then be represented making use of two different state spaces: 1. The ordinary phase space P, defined as an n d -dimensional real Euclidean space for which the coordinates are the instantaneous values of the SV [i.e., the entries of x(t )]; 2. The harmonic state space H, defined as an N T -dimensional real Euclidean space [N T = n d (2N + 1)] for which the coordinates are the entries of the harmonic state vector X H .
262
RF and Microwave Oscillator Design
Let us now assume that the circuit supports an M-autonomous electrical regime of the kind introduced in Section 5.2.1. The phases of the autonomous oscillations are not determined by the HB equations and can thus be arbitrarily selected. This means that adding an arbitrary real quantity ⌬⌽i to the phase of each autonomous oscillation changes a solution into another solution of the HB equations. Two such M-autonomous steady states have the same amplitude spectrum, while the phases of a generic intermodulation product (5.2) differ by the quantity [6] M
⌬⌽ k =
∑ k i ⌬⌽i
(5.24)
i=1
where k is the harmonic vector (5.3). Thus, in the H -space the family of M-autonomous regimes related by (5.24) with 0 ≤ ⌬⌽i < 2 is represented by an M-dimensional manifold (e.g., a closed surface for M = 2 or a closed line for M = 1). In most practical cases only the amplitude spectra of the oscillations are of interest, so that the states belonging to the family (5.24) may be considered equivalent to each other. Also, the actual values that the ⌬⌽i ’s take on in a real circuit will depend on the oscillation buildup process (e.g., on the particular noise waveform by which the process is started right after the excitations are turned on), so that the occurrence of a specific state of the same family cannot be predicted or distinguished from the other ones. This justifies the convention of taking one (arbitrarily chosen) state of the family as representative of the whole family (5.24). In the following we shall adopt a special case of the convention introduced in Section 5.2.2—that is, we shall arbitrarily set to zero the phase of the harmonic of a suitably selected SV, say, x n i (t ), at each autonomous fundamental frequency i . This uniquely defines the reduced state vector X (see Section 5.2.2). The domain of X is a subspace RH of the harmonic state space H. We shall conventionally call RH the autonomous state space. The entire family of quasi-periodic regimes (5.24) is represented by a single isolated point in the state space RH, so that the use of RH is particularly well-suited for obtaining simple pictorial representations of the complex bifurcation diagrams generated by the occurrence of instabilities in parameterized self-oscillating circuits. 5.3.1.2 Numerical Construction of a Solution Path
We now assume that a given nonlinear circuit is parameterized by a single real parameter P, representing any physical or electrical quantity affecting the circuit performance. Throughout this section we shall assume that P is the only independent variable available in the circuit. Since by assumption the
Modern Harmonic-Balance Techniques for Oscillator Analysis
263
tuning parameters T are not available, the HB solving system (5.11) describing the autonomous quasi-periodic steady states supported by the circuit may be cast in the form E(X, V ; P ) = 0
(5.25)
where the free parameter has been put into evidence for later convenience. Equation (5.25) is a real system of N T real equations in as many unknowns (the entries of X, V ). On the other hand, if the steady state of interest is forced, V is a priori known, but all phases are uniquely determined, so that (5.25) is replaced by E(X H ; P ) = 0
(5.26)
where the unknowns are now the entries of X H . We are thus in a position to treat autonomous and forced steady states in a unified way by introducing an auxiliary state vector of dimension N T , defined by
XA =
冦
冋 册 X V
for autonomous steady states
(5.27)
X H for nonautonomous (forced) steady states
so that the HB solving system may be cast in the unified form E(X A ; P ) = 0
(5.28)
By the implicit function theorem, (5.28) implicitly defines an equation of the form X A = X A (P )
(5.29)
representing a curve in the RH -space for autonomous steady states, or in the H -space for nonautonomous steady states. Such a curve will be named a solution path. As we will show in the rest of this chapter, the numerical construction of solution paths is an essential part of HB-based stability analysis of nonlinear circuits and thus deserves special attention. Building a solution path requires the computation of a continuous sequence of solutions of (5.28), which may represent a formidable task from the numerical viewpoint. It is thus of primary importance that the adopted nonlinear analysis
264
RF and Microwave Oscillator Design
strategy provides the best available numerical efficiency. For this reason, the mixed-mode Newton iteration discussed in Section 5.2.2 represents an excellent choice for this task. A peculiar advantage of this approach is that any steady state can be used as a good starting point in the search for its next neighbors, so that the quadratic convergence of the Newton iteration in the vicinity of the solution can be most efficiently exploited in the construction of the solution path. Although this analysis technique provides unsurpassed computational efficiency, it leads to numerical ill-conditioning when regular turning points are encountered on the solution path. A regular turning point is defined as a regular point of the curve where the parameter reaches a relative minimum or maximum, so that
| |
DP =0 D XA
(5.30)
where the differential operator D denotes the derivative taken along the solution path. If we now differentiate (5.28) with respect to P, taking (5.29) into account, we get J A (X A ; P )
D X A ∂E + DP ∂P
|
=0
(5.31)
X A = constant
where J A is the Jacobian matrix J A (X A ; P ) =
∂E ∂X A
|
(5.32) P = constant
From (5.31) we then obtain ∂E D XA = −[ J A (X A ; P )]−1 DP ∂P
|
(5.33) X A = constant
Due to (5.30), at a regular turning point || D X A /DP || becomes infinite. On the other hand, the partial derivatives ∂E /∂P appearing on the righthand side of (5.33) are not taken along the solution path and are thus regular at the turning point, which implies that the Jacobian matrix (5.32) must be singular. Solving (5.28) with respect to X A by a Newton iteration is then
Modern Harmonic-Balance Techniques for Oscillator Analysis
265
impossible at a turning point and is severely ill-conditioned in the close vicinity of it. In practice, if the solution path is generated by stepping the parameter and solving (5.28) with regards to X A for each value of P, the construction will stop before reaching the turning point due to failure of the Newton loop to achieve convergence. For a systematic and effective implementation of stability analysis in a general-purpose CAD environment (see Section 5.3.4) it is essential that solution paths can be efficiently generated with uniform accuracy and without requiring any manual intervention, irrespective of the presence of turning points. To reach this result, two kinds of actions must be taken: 1. In the vicinity of a turning point the solving system (5.28) must be replaced by an equivalent system free of numerical ill-conditioning. 2. A quantitative criterion must be implemented allowing the proximity of the singularity to be detected and the replacement to be carried out automatically. Regarding the first action necessary, the singularity of the Jacobian matrix (5.32) at a turning point originates from the fact that in its neighborhood the correspondence between the circuit state X A and the parameter P is not one-to-one. The correct behavior of the Newton-iteration based HB analysis may thus be restored by exchanging the roles of P and of one of the entries of the reduced state vector X, say, X P , in the vicinity of the turning point. We will denote by XA′ the vector generated by suppressing X P from the state vector X A , and by Z the modified state vector Z=
冋 册 XA′ P
(5.34)
In the neighborhood of a turning point, the HB system (5.28) may be rewritten in the form E(Z; X P ) = 0
(5.35)
and the solution path may be generated by stepping X P and solving (5.35) with regards to Z by a Newton iteration for each value of X P . In principle the real or imaginary part (or the magnitude) of any SV harmonic is eligible as X P , provided that the Jacobian matrix
266
RF and Microwave Oscillator Design
JZ =
∂E ∂Z
|
(5.36) X P = constant
is not singular at the turning point. This has the meaning of restoring the one-to-one correspondence between the points of the solution path and the auxiliary parameter X P . The implementation of the second condition requires a quantitative definition of the concept of neighborhood of a turning point. To ensure a uniform performance of the algorithm in general-purpose applications, such a definition should be as far as possible independent of the particular problem under consideration. Since the determinant of the Jacobian matrix (5.32) may change wildly as a function of the circuit topology and of the spectrum adopted in the HB analysis, it is not possible to establish in general whether the determinant is ‘‘close enough to zero.’’ In order to develop a ‘‘universal’’ switching criterion, we make use of the condition number of the Jacobian matrix, here defined as the ratio between the maximum and minimum magnitudes of the singular values, that is, [10]
( JA ) =
| S ( J A ) | max | S ( J A ) | min
(5.37)
where S(•) denotes a generic singular value of the matrix indicated in brackets. Note that = 1 for an identity matrix, while → ∞ for a singular matrix. Thus, ( J A ) is a normalized measure of the degree of ill-conditioning of the matrix J A . In the construction of the solution path we then use the formulation (5.28) of the HB equations when ( J A ) ≤ T and the formulation (5.35) when ( J A ) > T , where T is an empirically established threshold value. Excellent results have been obtained for a variety of circuits and spectra by taking T = 104 (see Section 5.3.5). The switching is operated automatically by the program at any time the condition number crosses the threshold. The derivatives of the parameter P and of the auxiliary parameter X P are continuously monitored during the generation of the solution path, so that the search can be restarted in the correct direction after a switching takes place. A similar criterion is also used to check that the auxiliary parameter X P has been properly chosen. The choice is considered acceptable if ( J Z ) ≤ T . If this condition is violated, the entries of the state vector X are tested in sequence until an acceptable choice is obtained.
Modern Harmonic-Balance Techniques for Oscillator Analysis
267
5.3.2 Natural Frequencies of Quasi-Periodic Steady States We denote by x ss (t ) a generic quasi-periodic steady state of the form (5.1) supported by a nonlinear circuit and assume that x ss (t ) is perturbed by a small self-excited signal of the form exp [( + j )t ] where and are real. Since by assumption the perturbation is small, only IM products that are first-order with respect to the perturbation need be retained in the analysis, so that the perturbed state may be represented in the form x(t ) = x ss (t ) +
∑ ⌬X k exp {[ + j ( + ⍀ k )] t }
(5.38)
k∈S
In (5.38) each frequency of the form + ⍀ k will be conventionally named a sideband, and ⌬X k is an n d -vector containing the (complex) phasors of the perturbations superimposed on the kth steady-state harmonics. Note that the complex form of the HB equations will be retained throughout this section because of the transient nature of the analysis to be carried out. In transient conditions the advantage of avoiding negative frequencies is lost, and the higher simplicity of the complex formulation prevails. We now replace (5.38) into (5.7) and linearize the nonlinear subnetwork equations in the neighborhood of x ss (t ). We obtain a set of equations of the form ⌬Vk = ⌬I k =
∑ P k, s ⌬X s
(5.39)
s∈S
∑ Q k, s ⌬X s
s∈S
where ⌬Vk , and ⌬I k are n d -vectors containing the phasors of the perturbations superimposed on the kth steady-state voltage and current harmonics, respectively. Starting from (5.7) and making use of the expansions (5.13), we can readily find explicit expressions for the matrices P k, s and Q k, s : n
P k, s =
∑ [ + j ( + ⍀ s )]m C m , k − s + C k − s exp {−[ + j ( + ⍀ s )]TD }
m=0 n
Q k, s =
D
∑ [ + j ( + ⍀ s )]m D m , k − s + D k − s exp {−[ + j ( + ⍀ s )]TD } D
m=0
(5.40)
268
RF and Microwave Oscillator Design
Note that the Fourier coefficients C and D are independent of ( + j ). In addition, the perturbation must obviously satisfy the linear subnetwork equations at all sidebands. Such equations may be written in the form Y[ + j ( + ⍀ k )]⌬Vk + ⌬I k = 0
(5.41)
(∀k ∈ S) where Y( j ) is the linear subnetwork admittance matrix. Combining (5.41) with (5.39) yields the homogeneous linear solving system
冦
∑ {Y[ + j ( + ⍀ k )]P k, s + Q k, s }⌬Xs = 0
s∈S
(5.42)
(∀k ∈ S)
which can be rewritten in the compact matrix notation R( + j )⌬X = 0
(5.43)
where the complex N T -vector ⌬X is the direct sum of the sideband perturbation vectors ⌬X s for all s ∈ S, and the submatrices of R( + j ) are given by R k, s = Y[ + j ( + ⍀ k )]P k, s + Q k, s
(5.44)
(∀k, s ∈ S) ⌬X may be interpreted as the spectrum of the perturbation superimposed on the circuit state. Note that (5.43) involves the sidebands only and is thus a complex linear system of N T equations in as many unknowns. The condition for the (autonomous) existence of the perturbation (i.e., ⌬X ≠ 0) is then D ( + j ) = det [R( + j )] = 0
(5.45)
The solutions of (5.45) are the natural frequencies of the quasi-periodic steady state. A steady state is stable if all of its natural frequencies have negative real parts. A steady state having one (at least) positive real natural frequency (but no complex natural frequency with positive real part) will be said synchronously unstable. A steady state having one (at least) complex natural frequency with a positive real part will be said asynchronously unstable.
Modern Harmonic-Balance Techniques for Oscillator Analysis
269
A stability analysis essentially consists of a search for the solutions of (5.45) having positive real parts, and for the physical conditions resulting in sign reversals of such real parts (bifurcations ). Considering that ⍀ −k = −⍀ k and that C m , −p = C m* , p (and the like), from (5.44) and (5.40), we get R k, s ( − j ) = Y[ + j (− + ⍀ k )]
冦 冦∑ n
⭈
D
m=0 n
+
冧 冧
∑ [ + j (− + ⍀ s )]m C m , k − s + C k − s exp {−[ + j (− + ⍀ s )]TD } D
[ + j ( + ⍀ s )]m D m , k − s + D k − s exp {−[ + j (− + ⍀ s )]TD }
m=0
= Y[ + j (− − ⍀ − k )]
冦∑ n
⭈
[ + j (− − ⍀ − s )]m (C m , s − k )*
m=0 D
+ (C s − k )* exp {−[ + j (− − ⍀ − s )]TD }
冦∑
冧
n
+
[ + j (− − ⍀ − s )]m (D m , s − k )*
m=0 D
+ (D s − k )* exp {−[ + j (− − ⍀ − s )]TD }
冧 (5.46)
Furthermore, assuming that the linear subnetwork is passive, its admittance matrix is positive real, so that (5.46) yields R k, s ( − j ) = {Y[ + j (− + ⍀ − k )]}*
冦∑ 冦∑ n
⭈
D
[ + j ( + ⍀ − s )]m C m , s − k + C s − k exp {−[ + j ( + ⍀ − s )]TD }
m=0 n
+
D
冧 冧
[ + j ( + ⍀ − s )]m D m , s − k + D s − k exp {−[ + j ( + ⍀ − s )]TD }
m=0
*
*
= [R − k, − s ( + j )]* (5.47)
270
RF and Microwave Oscillator Design
Since the spectrum is symmetric with respect to the origin, changing the sign of both k and s in (5.43) is equivalent to reversing the order of the intermodulation products ⍀ k , which leaves the determinant unchanged. In conclusion, we have D ( − j ) = [D ( + j )]*
(5.48)
so that the natural frequencies either are real or occur in complex conjugate pairs. In particular, (5.48) implies that D ( ) is real. For reasons to be explained in the following section, the particular case + j = 0 deserves some special attention. If we let + j = 0 in (5.38) and make use of (5.1), the perturbed state takes on the expression x(t ) = x ss (t ) +
∑ ⌬X k exp ( j ⍀ k t ) = ∑ (X k + ⌬X k ) exp ( j ⍀ k t )
k∈S
k∈S
(5.49) Let us assume that the unperturbed steady state is not a bifurcation. If such a state is forced, its harmonics X k are uniquely determined by the HB system. Equation (5.49) then implies that the only possible solution of (5.42) is ⌬X k = 0 ∀k ∈ S, which in turn requires D (0) ≠ 0. However, the situation is different for an autonomous steady state. Indeed, in this case the phases of the autonomous oscillations are indeterminate, as was discussed in Section 5.3.1, which means that (5.42) has infinitely many solutions defined by ⌬X k = [exp ( j ⌬⌽ k ) − 1]X k
(5.50)
where ⌬⌽ k is given by (5.24). As a consequence, the determinant of the linear solving system (5.42) must vanish, so that for an autonomous steady state D (0) = 0. 5.3.3 Nyquist’s Analysis for Time-Periodic Steady States If the unperturbed steady state is time-periodic with fundamental angular frequency 1 , an important property of the determinant (5.45) is of considerable help in the stability analysis. Recalling that the coefficients C and D are independent of ( + j ), by inspection of (5.40), we get
Modern Harmonic-Balance Techniques for Oscillator Analysis
271
R k , s [ + j ( + 1 ) = Y[ + j ( + 1 + k 1 )]
冦∑ n
⭈
[ + j ( + 1 + s 1 )]m C m , k − s
m=0 D
冧
+ C k − s exp {−[ + j ( + 1 + s 1 )]TD }
冦∑ n
+
[ + j ( + 1 + s 1 )]m D m , k − s
m=0 D
+ D k − s exp {−[ + j ( + 1 + s 1 )]TD }
冧
= R k + 1, s + 1 ( + j ) (5.51) Increasing by 1 thus results in a shift of the submatrixes of R along the principal diagonal in such a way that R k , s is replaced by R k + 1, s + 1 . If the number of positive harmonics N is infinite, this shift leaves the matrix unchanged, so that D ( + j ) is a periodic function of of period 1 . This behavior will be retained with some approximation if N is finite but sufficiently large. Due to such periodicity, each solution + j of (5.45) is actually representative of a numerable family of natural frequencies expressed by + j + jh 1 , where h is an arbitrary integer. Combining this property with (5.48), we find that two solutions of the form ± j 1 /2 represent the same natural frequency from a mathematical viewpoint and that D ( ± j 1 /2) is real. For practical purposes, the most relevant consequence of the periodicity property is that Nyquist’s analysis becomes easily applicable to (5.45). In order to apply Nyquist’s criterion [11], the complex frequency + j must be swept clockwise along a closed contour enclosing the entire right-hand half of the complex plane. This contour may consist of the j -axis (running from −j ∞ to +j ∞) ideally closed by a half-circle of infinite radius. The relevant information is then the number of turns around the origin made by the plot of D ( j ) as is swept from −∞ to +∞. This number is normally infinite for infinite N, because D ( + j ) then has an essential singularity at infinity owing to (5.40). This difficulty may be nicely overcome thanks to the periodicity of D ( j ), since the plot can be simply built by sweeping across the finite range [− 1 /2 ≤ ≤ 1 /2], so that the number of turns
272
RF and Microwave Oscillator Design
within each period automatically becomes finite. In particular, the essential singularity at infinity produces a finite number of counterclockwise turns of D ( + j ) around the origin in each interval of length 1 , in a way similar to a complex exponential function. Other properties of (5.42) allow for a simple formulation of the stability equation. If the linear subnetwork is passive, Y( + j ) is positive real and has no poles in the RHP. In addition, if circuit losses are properly taken into account, Y( + j ) is equally free from j -axis poles. The same is then true for D ( + j ) due to (5.44) and (5.40), so that the Nyquist plot becomes a bounded closed curve. The possible occurrence of zeros of D ( + j ) on the imaginary axis deserves some special attention. In a generic situation, that is, if we exclude the occurrence of particular cases (such as double zeros) requiring special circumstances to be verified, the condition D ( j C ) = 0
(5.52)
( C real) implies that the real part of one (at least) natural frequency undergoes a sign reversal as some circuit parameter is swept across a critical value for which (5.52) holds. In turn, this implies that the circuit stability portrait undergoes a qualitative change at criticality, such as turning from stable to unstable or the like. The only exception to this general rule is given by autonomous steady states, for which the condition D (0) = 0 always holds, as shown in Section 5.3.2. The origin of the complex plane thus automatically lies on the Nyquist plot of an autonomous steady state without implying a stability change. The steady states for which (5.52) holds (with the additional condition C ≠ 0 in the autonomous case) are called bifurcations. This name is intuitively explained by the fact that new branches of the solution path are originated (or terminated) at bifurcations, as discussed in Section 5.3.4. Under the assumption that the steady state under consideration is not a bifurcation, D ( j ) has no j -axis zeros if the steady state is forced, and has a simple zero at = 0 if the steady state is autonomous. We are now in a position to state Nyquist’s stability criterion for a generic periodic steady state. If the steady state is forced, the equation takes on the form [12] NZ = NC + N∞
(5.53)
where: N Z = number of zeros of D( + j ) lying in the rectangular domain [ > 0, − 1 /2 ≤ ≤ 1 /2];
Modern Harmonic-Balance Techniques for Oscillator Analysis
273
N C = number of clockwise turns around the origin made by D( j ) as is swept across the range [− 1 /2 ≤ ≤ 1 /2], owing to the zeros of D( + j ) lying in the rectangular domain [ > 0, − 1 /2 ≤ ≤ 1 /2]; N ∞ = number of counterclockwise turns around the origin made by D( j ) as is swept across the range [− 1 /2 ≤ ≤ 1 /2], owing to the essential singularity of D( + j ) at infinity. If the steady state is autonomous, the origin lies on the plot, so that (5.53) is replaced by
NZ = NC + N∞ −
1 2
(5.54)
In (5.53) and (5.54), N C represents the total phase change of D ( j ) around the plot divided by 2 and may be easily obtained by inspection of the Nyquist plot, while N ∞ is unknown. However, (5.44) and (5.40) clearly show that the order of the essential singularity at infinity only depends on the size of the submatrixes R k , s and on the maximum order n of the derivatives appearing in the device equations (5.7). Thus, N ∞ is normally a constant for all the periodic steady states of a given circuit, and can be computed once for all by carrying out a Nyquist stability analysis for a state having a known N Z . As an example, such a state can be found by passivating the circuit (i.e., turning off the bias sources of all active devices), and reducing the amplitude(s) of the RF source(s) in such a way that the circuit behaves linearly. Since the Nyquist plot may be quite complicated for large circuits (i.e., N ∞ may be large), it is usually convenient to apply Nyquist’s criterion to the auxiliary function
冋
F ( + j ) = exp −
册
2 N ∞ ( + j ) D ( + j ) 1
(5.55)
F ( + j ) has obviously the same zeros as D ( + j ), but for it N ∞ = 0, so that N C may be evaluated much more easily. When (5.55) is used, (5.53) and (5.54) are replaced by
274
RF and Microwave Oscillator Design
NZ = NC NZ = NC −
(5.56) 1 2
(5.57)