TLFeBOOK
40816_FM_pi-xvii
10/22/01
12:37 PM
40816 HICKS Mcghp FM
Page i
Second Pass
bcj 7/19/01 p.i
CIVIL ENGINEERING FORMULAS
TLFeBOOK
This page intentionally left blank.
TLFeBOOK
40816_FM_pi-xvii
10/22/01
12:37 PM
40816 HICKS Mcghp FM
Page iii
Second Pass
bcj 7/19/01 p.iii
CIVIL ENGINEERING FORMULAS Tyler G. Hicks, P.E. International Engineering Associates Member: American Society of Mechanical Engineers United States Naval Institute
McGRAW-HILL New York Chicago San Francisco Lisbon London Madrid Mexico City Milan New Delhi San Juan Seoul Singapore Sydney Toronto
TLFeBOOK
abc
McGraw-Hill
Copyright © 2002 by The McGraw-Hill Companies. All rights reserved. Manufactured in the United States of America. Except as permitted under the United States Copyright Act of 1976, no part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of the publisher. 0-07-139542-3 The material in this eBook also appears in the print version of this title: 0-07-135612-3. All trademarks are trademarks of their respective owners. Rather than put a trademark symbol after every occurrence of a trademarked name, we use names in an editorial fashion only, and to the benefit of the trademark owner, with no intention of infringement of the trademark. Where such designations appear in this book, they have been printed with initial caps. McGraw-Hill eBooks are available at special quantity discounts to use as premiums and sales promotions, or for use in corporate training programs. For more information, please contact George Hoare, Special Sales, at
[email protected] or (212) 904-4069.
TERMS OF USE This is a copyrighted work and The McGraw-Hill Companies, Inc. (“McGraw-Hill”) and its licensors reserve all rights in and to the work. Use of this work is subject to these terms. Except as permitted under the Copyright Act of 1976 and the right to store and retrieve one copy of the work, you may not decompile, disassemble, reverse engineer, reproduce, modify, create derivative works based upon, transmit, distribute, disseminate, sell, publish or sublicense the work or any part of it without McGraw-Hill’s prior consent. You may use the work for your own noncommercial and personal use; any other use of the work is strictly prohibited. Your right to use the work may be terminated if you fail to comply with these terms. THE WORK IS PROVIDED “AS IS”. McGRAW-HILL AND ITS LICENSORS MAKE NO GUARANTEES OR WARRANTIES AS TO THE ACCURACY, ADEQUACY OR COMPLETENESS OF OR RESULTS TO BE OBTAINED FROM USING THE WORK, INCLUDING ANY INFORMATION THAT CAN BE ACCESSED THROUGH THE WORK VIA HYPERLINK OR OTHERWISE, AND EXPRESSLY DISCLAIM ANY WARRANTY, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. McGraw-Hill and its licensors do not warrant or guarantee that the functions contained in the work will meet your requirements or that its operation will be uninterrupted or error free. Neither McGraw-Hill nor its licensors shall be liable to you or anyone else for any inaccuracy, error or omission, regardless of cause, in the work or for any damages resulting therefrom. McGraw-Hill has no responsibility for the content of any information accessed through the work. Under no circumstances shall McGrawHill and/or its licensors be liable for any indirect, incidental, special, punitive, consequential or similar damages that result from the use of or inability to use the work, even if any of them has been advised of the possibility of such damages. This limitation of liability shall apply to any claim or cause whatsoever whether such claim or cause arises in contract, tort or otherwise. DOI: 10.1036/0071395423
TLFeBOOK
40816_FM_pi-xvii
10/22/01
12:37 PM
40816 HICKS Mcghp FM
Page v
Second Pass
bcj 7/19/01 p.v
CONTENTS 9
. t n -
Preface xiii Acknowledgments xv How to Use This Book xvii
Chapter 1. Conversion Factors for Civil Engineering Practice
Chapter 2. Beam Formulas
1
15
Continuous Beams / 16 Ultimate Strength of Continuous Beams / 53 Beams of Uniform Strength / 63 Safe Loads for Beams of Various Types / 64 Rolling and Moving Loads / 79 Curved Beams / 82 Elastic Lateral Buckling of Beams / 88 Combined Axial and Bending Loads / 92 Unsymmetrical Bending / 93 Eccentric Loading / 94 Natural Circular Frequencies and Natural Periods of Vibration of Prismatic Beams / 96 TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_FM_pi-xvii
10/22/01
40816 HICKS Mcghp FM
vi
12:37 PM
Page vi
Second Pass bcj 7/19/01 p.vi
CONTENTS
Chapter 3. Column Formulas
99
General Considerations / 100 Short Columns / 102 Eccentric Loads on Columns / 102 Column Base Plate Design / 111 American Institute of Steel Construction Allowable-Stress Design Approach / 113 Composite Columns / 115 Elastic Flexural Buckling of Columns / 118 Allowable Design Loads for Aluminum Columns / 121 Ultimate-Strength Design of Concrete Columns / 124
Chapter 4. Piles and Piling Formulas
W U W
131
Allowable Loads on Piles / 132 Laterally Loaded Vertical Piles / 133 Toe Capacity Load / 134 Groups of Piles / 136 Foundation-Stability Analysis / 139 Axial-Load Capacity of Single Piles / 143 Shaft Settlement / 144 Shaft Resistance to Cohesionless Soil / 145
Chapter 5. Concrete Formulas
T C C R D U
147
Reinforced Concrete / 148 Water/Cementitious Materials Ratio / 148 Job Mix Concrete Volume / 149 Modulus of Elasticity of Concrete / 150 Tensile Strength of Concrete / 151 Reinforcing Steel / 151 Continuous Beams and One-Way Slabs / 151 Design Methods for Beams, Columns, and Other Members / 153 Properties in the Hardened State / 167 TLFeBOOK
U W U W F F S C S B L S C C W
C G S B B C C
40816_FM_pi-xvii
10/22/01
40816 HICKS Mcghp FM
viii
12:37 PM
Page viii
Second Pass bcj 7/19/01 p.viii
CONTENTS
Compression at Angle to Grain / 220 Recommendations of the Forest Products Laboratory / 221 Compression on Oblique Plane / 223 Adjustments Factors for Design Values / 224 Fasteners for Wood / 233 Adjustment of Design Values for Connections with Fasteners / 236 Roof Slope to Prevent Ponding / 238 Bending and Axial Tension / 239 Bending and Axial Compression / 240
Chapter 7. Surveying Formulas
C F S V
C
243
Units of Measurement / 244 Theory of Errors / 245 Measurement of Distance with Tapes / 247 Vertical Control / 253 Stadia Surveying / 253 Photogrammetry / 255
Chapter 8. Soil and Earthwork Formulas
257
Physical Properties of Soils / 258 Index Parameters for Soils / 259 Relationship of Weights and Volumes in Soils / 261 Internal Friction and Cohesion / 263 Vertical Pressures in Soils / 264 Lateral Pressures in Soils, Forces on Retaining Walls / 265 Lateral Pressure of Cohesionless Soils / 266 Lateral Pressure of Cohesive Soils / 267 Water Pressure / 268 Lateral Pressure from Surcharge / 268 Stability of Slopes / 269 Bearing Capacity of Soils / 270 Settlement under Foundations / 271 Soil Compaction Tests / 272
L A L A L A S B C B P L C W D F C N P
C F S A L A S H TLFeBOOK
40816_FM_pi-xvii
10/22/01
12:37 PM
40816 HICKS Mcghp FM
Page ix
Second Pass
bcj 7/19/01 p.ix
ix
CONTENTS
Compaction Equipment / 275 Formulas for Earthmoving / 276 Scraper Production / 278 Vibration Control in Blasting / 280
Chapter 9. Building and Structures Formulas
3
7
283
Load-and-Resistance Factor Design for Shear in Buildings / 284 Allowable-Stress Design for Building Columns / 285 Load-and-Resistance Factor Design for Building Columns / 287 Allowable-Stress Design for Building Beams / 287 Load-and-Resistance Factor Design for Building Beams / 290 Allowable-Stress Design for Shear in Buildings / 295 Stresses in Thin Shells / 297 Bearing Plates / 298 Column Base Plates / 300 Bearing on Milled Surfaces / 301 Plate Girders in Buildings / 302 Load Distribution to Bents and Shear Walls / 304 Combined Axial Compression or Tension and Bending / 306 Webs under Concentrated Loads / 308 Design of Stiffeners under Loads / 311 Fasteners for Buildings / 312 Composite Construction / 313 Number of Connectors Required for Building Construction / 316 Ponding Considerations in Buildings / 318
Chapter 10. Bridge and Suspension-Cable Formulas
321
Shear Strength Design for Bridges / 322 Allowable-Stress Design for Bridge Columns / 323 Load-and-Resistance Factor Design for Bridge Columns / 324 Allowable-Stress Design for Bridge Beams / 325 Stiffeners on Bridge Girders / 327 Hybrid Bridge Girders / 329 TLFeBOOK
40816_FM_pi-xvii
10/22/01
40816 HICKS Mcghp FM
x
12:37 PM
Page x
Second Pass bcj 7/19/01 p.x
CONTENTS
Load-Factor Design for Bridge Beams / 330 Bearing on Milled Surfaces / 332 Bridge Fasteners / 333 Composite Construction in Highway Bridges / 333 Number of Connectors in Bridges / 337 Allowable-Stress Design for Shear in Bridges / 339 Maximum Width/Thickness Ratios for Compression Elements for Highway Bridges / 341 Suspension Cables / 341 General Relations for Suspension Cables / 345 Cable Systems / 353
Chapter 11. Highway and Road Formulas
355
Circular Curves / 356 Parabolic Curves / 359 Highway Curves and Driver Safety / 361 Highway Alignments / 362 Structural Numbers for Flexible Pavements / 365 Transition (Spiral) Curves / 370 Designing Highway Culverts / 371 American Iron and Steel Institute (AISI) Design Procedure / 374
Chapter 12. Hydraulics and Waterworks Formulas
F O W P T F C O M H N W F P E M C G W F E V H
381
Capillary Action / 382 Viscosity / 386 Pressure on Submerged Curved Surfaces / 387 Fundamentals of Fluid Flow / 388 Similitude for Physical Models / 392 Fluid Flow in Pipes / 395 Pressure (Head) Changes Caused by Pipe Size Change / 403 Flow through Orifices / 406 TLFeBOOK
40816_FM_pi-xvii
10/22/01
12:37 PM
40816 HICKS Mcghp FM
Page xi
Second Pass
bcj 7/19/01 p.xi
xi
CONTENTS
5
Fluid Jets / 409 Orifice Discharge into Diverging Conical Tubes / 410 Water Hammer / 412 Pipe Stresses Perpendicular to the Longitudinal Axis / 412 Temperature Expansion of Pipe / 414 Forces Due to Pipe Bends / 414 Culverts / 417 Open-Channel Flow / 420 Manning’s Equation for Open Channels / 424 Hydraulic Jump / 425 Nonuniform Flow in Open Channels / 429 Weirs / 436 Flow Over Weirs / 438 Prediction of Sediment-Delivery Rate / 440 Evaporation and Transpiration / 442 Method for Determining Runoff for Minor Hydraulic Structures / 443 Computing Rainfall Intensity / 443 Groundwater / 446 Water Flow for Firefighting / 446 Flow from Wells / 447 Economical Sizing of Distribution Piping / 448 Venturi Meter Flow Computation / 448 Hydroelectric Power Generation / 449
Index
451
1
TLFeBOOK
This page intentionally left blank.
TLFeBOOK
40816_FM_pi-xvii
10/22/01
12:37 PM
40816 HICKS Mcghp FM
Page xiii
Second Pass
bcj 7/19/01 p.xiii
PREFACE
This handy book presents more than 2000 needed formulas for civil engineers to help them in the design office, in the field, and on a variety of construction jobs, anywhere in the world. These formulas are also useful to design drafters, structural engineers, bridge engineers, foundation builders, field engineers, professional-engineer license examination candidates, concrete specialists, timber-structure builders, and students in a variety of civil engineering pursuits. The book presents formulas needed in 12 different specialized branches of civil engineering—beams and girders, columns, piles and piling, concrete structures, timber engineering, surveying, soils and earthwork, building structures, bridges, suspension cables, highways and roads, and hydraulics and open-channel flow. Key formulas are presented for each of these topics. Each formula is explained so the engineer, drafter, or designer knows how, where, and when to use the formula in professional work. Formula units are given in both the United States Customary System (USCS) and System International (SI). Hence, the text is usable throughout the world. To assist the civil engineer using this material in worldwide engineering practice, a comprehensive tabulation of conversion factors is presented in Chapter 1. In assembling this collection of formulas, the author was guided by experts who recommended the areas of TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_FM_pi-xvii
10/22/01
40816 HICKS Mcghp FM
xiv
12:37 PM
Page xiv
Second Pass bcj 7/19/01 p.xiv
PREFACE
greatest need for a handy book of practical and applied civil engineering formulas. Sources for the formulas presented here include the various regulatory and industry groups in the field of civil engineering, authors of recognized books on important topics in the field, drafters, researchers in the field of civil engineering, and a number of design engineers who work daily in the field of civil engineering. These sources are cited in the Acknowledgments. When using any of the formulas in this book that may come from an industry or regulatory code, the user is cautioned to consult the latest version of the code. Formulas may be changed from one edition of a code to the next. In a work of this magnitude it is difficult to include the latest formulas from the numerous constantly changing codes. Hence, the formulas given here are those current at the time of publication of this book. In a work this large it is possible that errors may occur. Hence, the author will be grateful to any user of the book who detects an error and calls it to the author’s attention. Just write the author in care of the publisher. The error will be corrected in the next printing. In addition, if a user believes that one or more important formulas have been left out, the author will be happy to consider them for inclusion in the next edition of the book. Again, just write him in care of the publisher. Tyler G. Hicks, P.E.
A
M t a H a w F p w a L N e p F a s f e w p t
TLFeBOOK
40816_FM_pi-xvii
10/22/01
12:37 PM
40816 HICKS Mcghp FM
Page xv
Second Pass
bcj 7/19/01 p.xv
l n n e t r . o o e . k . l t o .
ACKNOWLEDGMENTS
Many engineers, professional societies, industry associations, and governmental agencies helped the author find and assemble the thousands of formulas presented in this book. Hence, the author wishes to acknowledge this help and assistance. The author’s principal helper, advisor, and contributor was the late Frederick S. Merritt, P.E., Consulting Engineer. For many years Fred and the author were editors on companion magazines at The McGraw-Hill Companies. Fred was an editor on Engineering-News Record, whereas the author was an editor on Power magazine. Both lived on Long Island and traveled on the same railroad to and from New York City, spending many hours together discussing engineering, publishing, and book authorship. When the author was approached by the publisher to prepare this book, he turned to Fred Merritt for advice and help. Fred delivered, preparing many of the formulas in this book and giving the author access to many more in Fred’s extensive files and published materials. The author is most grateful to Fred for his extensive help, advice, and guidance. Further, the author thanks the many engineering societies, industry associations, and governmental agencies whose work is referred to in this publication. These organizations provide the framework for safe design of numerous structures of many different types. TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_FM_pi-xvii
10/22/01
40816 HICKS Mcghp FM
xvi
12:37 PM
Page xvi
Second Pass bcj 7/19/01 p.xvi
ACKNOWLEDGMENTS
The author also thanks Larry Hager, Senior Editor, Professional Group, The McGraw-Hill Companies, for his excellent guidance and patience during the long preparation of the manuscript for this book. Finally, the author thanks his wife, Mary Shanley Hicks, a publishing professional, who always most willingly offered help and advice when needed. Specific publications consulted during the preparation of this text include: American Association of State Highway and Transportation Officials (AASHTO) “Standard Specifications for Highway Bridges”; American Concrete Institute (ACI) “Building Code Requirements for Reinforced Concrete”; American Institute of Steel Construction (AISC) “Manual of Steel Construction,” “Code of Standard Practice,” and “Load and Resistance Factor Design Specifications for Structural Steel Buildings”; American Railway Engineering Association (AREA) “Manual for Railway Engineering”; American Society of Civil Engineers (ASCE) “Ground Water Management”; American Water Works Association (AWWA) “Water Quality and Treatment.” In addition, the author consulted several hundred civil engineering reference and textbooks dealing with the topics in the current book. The author is grateful to the writers of all the publications cited here for the insight they gave him to civil engineering formulas. A number of these works are also cited in the text of this book.
TLFeBOOK
T c d s p n T i S o d c c l e d i d a
40816_FM_pi-xvii
10/22/01
12:37 PM
40816 HICKS Mcghp FM
s n s , n f y e ) y y s r d e e y e
Page xvii
Second Pass
bcj 7/19/01 p.xvii
HOW TO USE THIS BOOK
The formulas presented in this book are intended for use by civil engineers in every aspect of their professional work— design, evaluation, construction, repair, etc. To find a suitable formula for the situation you face, start by consulting the index. Every effort has been made to present a comprehensive listing of all formulas in the book. Once you find the formula you seek, read any accompanying text giving background information about the formula. Then when you understand the formula and its applications, insert the numerical values for the variables in the formula. Solve the formula and use the results for the task at hand. Where a formula may come from a regulatory code, or where a code exists for the particular work being done, be certain to check the latest edition of the applicable code to see that the given formula agrees with the code formula. If it does not agree, be certain to use the latest code formula available. Remember, as a design engineer you are responsible for the structures you plan, design, and build. Using the latest edition of any governing code is the only sensible way to produce a safe and dependable design that you will be proud to be associated with. Further, you will sleep more peacefully! TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
This page intentionally left blank.
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 1
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
CHAPTER 1
CONVERSION FACTORS FOR CIVIL ENGINEERING PRACTICE
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_01_p1-14
10/22/01
12:38 PM
Page 2
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
2
CHAPTER ONE
Civil engineers throughout the world accept both the United States Customary System (USCS) and the System International (SI) units of measure for both applied and theoretical calculations. However, the SI units are much more widely used than those of the USCS. Hence, both the USCS and the SI units are presented for essentially every formula in this book. Thus, the user of the book can apply the formulas with confidence anywhere in the world. To permit even wider use of this text, this chapter contains the conversion factors needed to switch from one system to the other. For engineers unfamiliar with either system of units, the author suggests the following steps for becoming acquainted with the unknown system: 1. Prepare a list of measurements commonly used in your daily work. 2. Insert, opposite each known unit, the unit from the other system. Table 1.1 shows such a list of USCS units with corresponding SI units and symbols prepared by a civil engineer who normally uses the USCS. The SI units shown in Table 1.1 were obtained from Table 1.3 by the engineer. 3. Find, from a table of conversion factors, such as Table 1.3, the value used to convert from USCS to SI units. Insert each appropriate value in Table 1.2 from Table 1.3. 4. Apply the conversion values wherever necessary for the formulas in this book. 5. Recognize—here and now—that the most difficult aspect of becoming familiar with a new system of measurement is becoming comfortable with the names and magnitudes of the units. Numerical conversion is simple, once you have set up your own conversion table.
TLFeBOOK
T
s c p p f k g k †
w
c a u c F d
40816_01_p1-14
10/22/01
12:38 PM
Page 3
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
3
CONVERSION FACTORS
e m d h e y y r r r r h l s e , t e t d ,
TABLE 1.1 Commonly Used USCS and SI Units† Conversion factor (multiply USCS unit by this factor to SI symbol obtain SI unit)
USCS unit
SI unit
square foot cubic foot pound per square inch pound force foot pound torque kip foot gallon per minute kip per square inch
square meter cubic meter
m2 m3
0.0929 0.2831
kilopascal newton
kPa Nu
6.894 4.448
newton meter kilonewton meter
Nm kNm
1.356 1.355
liter per second
L/s
0.06309
megapascal
MPa
6.89
†
This table is abbreviated. For a typical engineering practice, an actual table would be many times this length.
Be careful, when using formulas containing a numerical constant, to convert the constant to that for the system you are using. You can, however, use the formula for the USCS units (when the formula is given in those units) and then convert the final result to the SI equivalent using Table 1.3. For the few formulas given in SI units, the reverse procedure should be used.
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 4
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
4
CHAPTER ONE
TABLE 1.2 Typical Conversion Table† To convert from
To
square foot foot per second squared cubic foot pound per cubic inch gallon per minute pound per square inch pound force kip per square foot acre foot per day
square meter meter per second squared cubic meter kilogram per cubic meter liter per second
acre cubic foot per second
kilopascal newton pascal cubic meter per second square meter cubic meter per second
T Multiply by‡ 9.290304
E 02
3.048 2.831685
E 01 E 02
2.767990 6.309
E 04 E 02
6.894757 4.448222 4.788026
a a a a a
b b E 04 E 02
1.427641 4.046873
E 03
2.831685
E 02
b B B
†
This table contains only selected values. See the U.S. Department of the Interior Metric Manual, or National Bureau of Standards, The International System of Units (SI), both available from the U.S. Government Printing Office (GPO), for far more comprehensive listings of conversion factors. ‡ The E indicates an exponent, as in scientific notation, followed by a positive or negative number, representing the power of 10 by which the given conversion factor is to be multiplied before use. Thus, for the square foot conversion factor, 9.290304 1/100 0.09290304, the factor to be used to convert square feet to square meters. For a positive exponent, as in converting acres to square meters, multiply by 4.046873 1000 4046.8. Where a conversion factor cannot be found, simply use the dimensional substitution. Thus, to convert pounds per cubic inch to kilograms per cubic meter, find 1 lb 0.4535924 kg and 1 in3 0.00001638706 m3. Then, 1 lb/in3 0.4535924 kg/0.00001638706 m3 27,680.01, or 2.768 E 4.
TLFeBOOK
B
B
B
40816_01_p1-14
10/22/01
12:38 PM
Page 5
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
5
CONVERSION FACTORS
TABLE 1.3 Factors for Conversion to SI Units of Measurement
2 1 2 4 2
4 2 3 2
e
To convert from
To
acre foot, acre ft acre angstrom, Å atmosphere, atm (standard) atmosphere, atm (technical 1 kgf/cm2) bar barrel (for petroleum, 42 gal) board foot, board ft British thermal unit, Btu, (mean) British thermal unit, Btu (International Table)in/(h)(ft2) (°F) (k, thermal conductivity) British thermal unit, Btu (International Table)/h British thermal unit, Btu (International Table)/(h)(ft2)(°F) (C, thermal conductance) British thermal unit, Btu (International Table)/lb
cubic meter, m3 square meter, m2 meter, m pascal, Pa
1.233489 4.046873 1.000000* 1.013250*
Multiply by
pascal, Pa
9.806650* E 04
pascal, Pa cubic meter, m2
1.000000* E 05 1.589873 E 01
cubic meter, m3 joule, J
2.359737 1.05587
E 03 E 03
watt per meter kelvin, W/(mK)
1.442279
E 01
watt, W
2.930711
E 01
watt per square meter kelvin, W/(m2K)
5.678263
E 00
joule per kilogram, J/kg
2.326000* E 03
E 03 E 03 E 10 E 05
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 6
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
6
CHAPTER ONE
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued) To convert from British thermal unit, Btu (International Table)/(lb)(°F) (c, heat capacity) British thermal unit, cubic foot, Btu (International Table)/ft3 bushel (U.S.) calorie (mean) candela per square inch, cd/in2 centimeter, cm, of mercury (0°C) centimeter, cm, of water (4°C) chain circular mil day day (sidereal) degree (angle) degree Celsius degree Fahrenheit degree Fahrenheit degree Rankine (°F)(h)(ft2)/Btu (International Table) (R, thermal resistance)
To
T (
Multiply by
joule per kilogram kelvin, J/(kgK)
4.186800* E 03
(
joule per cubic meter, J/m3
3.725895
E 04
cubic meter, m3 joule, J candela per square meter, cd/m2 pascal, Pa
3.523907 4.19002 1.550003
E 02 E 00 E 03
d f f f f
1.33322
E 03
pascal, Pa
9.80638
E 01
meter, m square meter, m2
2.011684 E 01 5.067075 E 10 8.640000* E 04 8.616409 E 04 1.745329 E 02 TK tC 273.15 tC (tF 32)/1.8 TK (tF 459.67)/1.8 TK TR /1.8 1.761102 E 01
second, s second, s radian, rad kelvin, K degree Celsius, °C kelvin, K kelvin, K kelvin square meter per watt, Km2/W
s s
s c c c f
f f
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 7
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
7
CONVERSION FACTORS
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued) To convert from 2
8
To
Multiply by E 00
(°F)(h)(ft )/(Btu (International Table)in) (thermal resistivity) dyne, dyn
kelvin meter per watt, Km/W
fathom foot, ft foot, ft (U.S. survey) foot, ft, of water (39.2°F) (pressure) square foot, ft2 square foot per hour, ft2/h (thermal diffusivity) square foot per second, ft2/s cubic foot, ft3 (volume or section modulus) cubic foot per minute, ft3/min cubic foot per second, ft3/s foot to the fourth power, ft4 (area moment of inertia) foot per minute, ft/min foot per second, ft/s
meter, m meter, m meter, m pascal, Pa
1.828804 3.048000† 3.048006 2.98898
square meter, m2 square meter per second, m2/s
9.290304† E 02 2.580640† E 05
square meter per second, m2/s cubic meter, m3
9.290304† E 02
newton, N
cubic meter per second, m3/s cubic meter per second, m3/s meter to the fourth power, m4 meter per second, m/s meter per second, m/s
6.933471
1.000000† E 05 E 00 E 01 E 01 E 03
2.831685
E 02
4.719474
E 04
2.831685
E 02
8.630975
E 03
5.080000† E 03 3.048000† E 01
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 8
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
8
CHAPTER ONE
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued) To convert from foot per second squared, ft/s2 footcandle, fc footlambert, fL foot pound force, ftlbf foot pound force per minute, ftlbf/min foot pound force per second, ftlbf/s foot poundal, ft poundal free fall, standard g gallon, gal (Canadian liquid) gallon, gal (U.K. liquid) gallon, gal (U.S. dry) gallon, gal (U.S. liquid) gallon, gal (U.S. liquid) per day gallon, gal (U.S. liquid) per minute grad grad grain, gr gram, g
To
Multiply by
meter per second squared, m/s2 lux, lx candela per square meter, cd/m2 joule, J watt, W
3.048000† E 01 1.076391 3.426259
E 01 E 00
1.355818 2.259697
E 00 E 02
watt, W
1.355818
E 00
joule, J
4.214011
E 02
meter per second squared, m/s2
9.806650† E 00
cubic meter, m3
4.546090
E 03
cubic meter, m3
4.546092
E 03
cubic meter, m3 cubic meter, m3
4.404884 3.785412
E 03 E 03
cubic meter per second, m3/s cubic meter per second, m3/s degree (angular) radian, rad kilogram, kg kilogram, kg
4.381264
E 08
6.309020
E 05
9.000000† 1.570796 6.479891† 1.000000†
E 01 E 02 E 05 E 03
T (
h h h h h h h h i i i i
s c
i
TLFeBOOK
i
40816_01_p1-14
10/22/01
12:38 PM
Page 9
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
9
CONVERSION FACTORS
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued) To convert from 1 1 0 0 2 0 2 0 3 3 3 3 8 5 1 2 5 3
hectare, ha horsepower, hp (550 ftlbf/s) horsepower, hp (boiler) horsepower, hp (electric) horsepower, hp (water) horsepower, hp (U.K.) hour, h hour, h (sidereal) inch, in inch of mercury, in Hg (32°F) (pressure) inch of mercury, in Hg (60°F) (pressure) inch of water, in H2O (60°F) (pressure) square inch, in2 cubic inch, in3 (volume or section modulus) inch to the fourth power, in4 (area moment of inertia) inch per second, in/s
To
Multiply by
square meter, m watt, W
1.000000† E 04 7.456999 E 02
watt, W
9.80950
watt, W
7.460000† E 02
watt, W
7.46043†
E 02
watt, W second, s second, s meter, m pascal, Pa
7.4570 3.600000† 3.590170 2.540000† 3.38638
E 02 E 03 E 03
pascal, Pa
3.37685
E 03
pascal, Pa
2.4884
E 02
square meter, m2 cubic meter, m3
6.451600† E 04 1.638706 E 05
meter to the fourth power, m4
4.162314
meter per second, m/s
2.540000† E 02
2
E 03
E 02 E 03
E 07
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 10
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
10
CHAPTER ONE
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued)
T (
To convert from
To
Multiply by
kelvin, K kilogram force, kgf kilogram force meter, kgm kilogram force second squared per meter, kgfs2/m (mass) kilogram force per square centimeter, kgf/cm2 kilogram force per square meter, kgf/m2 kilogram force per square millimeter, kgf/mm2 kilometer per hour, km/h kilowatt hour, kWh kip (1000 lbf) kipper square inch, kip/in2 ksi knot, kn (international)
degree Celsius, °C newton, N newton meter, Nm kilogram, kg
tC TK 273.15 9.806650† E 00 9.806650† E 00
pascal, Pa
9.806650† E 04
m s
pascal, Pa
9.806650† E 00
s
pascal, Pa
9.806650† E 06
m m meter per second, m/s joule, J newton, N pascal, Pa
liter
meter per second, m/s candela per square meter, cd/m cubic meter, m3
maxwell mho
weber, Wb siemens, S
lambert, L
9.806650† E 00
m m m m m m
2.777778 E 01 3.600000† E 06 4.448222 E 03 6.894757 E 06
m m
5.144444 E 01
m m m o
3.183099 E 03
o
1.000000† E 03 1.000000† E 08 1.000000† E 00
o o o
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 11
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
11
CONVERSION FACTORS
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued) To convert from 0 0 0
4
0
6
1 6 3 6 1 3 3 8 0
microinch, in micron, m mil, mi mile, mi (international) mile, mi (U.S. statute) mile, mi (international nautical) mile, mi (U.S. nautical) square mile, mi2 (international) square mile, mi2 (U.S. statute) mile per hour, mi/h (international) mile per hour, mi/h (international) millibar, mbar millimeter of mercury, mmHg (0°C) minute (angle) minute, min minute (sidereal) ounce, oz (avoirdupois) ounce, oz (troy or apothecary) ounce, oz (U.K. fluid) ounce, oz (U.S. fluid) ounce force, ozf
To
Multiply by E 08 E 06 E 05 E 03 E 03 E 03
meter, m meter, m meter, m meter, m meter, m meter, m
2.540000† 1.000000† 2.540000† 1.609344† 1.609347 1.852000†
meter, m square meter, m2
1.852000† E 03 2.589988 E 06
square meter, m2
2.589998 E 06
meter per second, m/s kilometer per hour, km/h pascal, Pa pascal, Pa
4.470400† E 01 1.609344† E 00 1.000000† E 02 1.33322 E 02 E 04 E 01 E 01 E 02
radian, rad second, s second, s kilogram, kg
2.908882 6.000000† 5.983617 2.834952
kilogram, kg
3.110348 E 02
cubic meter, m3 cubic meter, m3 newton, N
2.841307 E 05 2.957353 E 05 2.780139 E 01
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 12
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
12
CHAPTER ONE
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued) To convert from ounce forceinch, ozfin ounce per square foot, oz (avoirdupois)/ft2 ounce per square yard, oz (avoirdupois)/yd2 perm (0°C)
perm (23°C)
perm inch, permin (0°C) perm inch, permin (23°C) pint, pt (U.S. dry) pint, pt (U.S. liquid) poise, p (absolute viscosity) pound, lb (avoirdupois) pound, lb (troy or apothecary) pound square inch, lbin2 (moment of inertia)
To newton meter, Nm kilogram per square meter, kg/m2 kilogram per square meter, kg/m2 kilogram per pascal second meter, kg/(Pasm) kilogram per pascal second meter, kg/(Pasm) kilogram per pascal second meter, kg/(Pasm) kilogram per pascal second meter, kg/(Pasm) cubic meter, m3 cubic meter, m3 pascal second, Pas kilogram, kg
T (
Multiply by 7.061552 E 03
p
3.051517 E 01
p
3.390575 E 02
p
5.72135
E 11
p
5.74525
E 11
1.45322
E 12
1.45929
E 12
p p p p
5.506105 E 04 4.731765 E 04 1.000000† E 01
p p
4.535924 E 01
p p p
kilogram, kg
3.732417 E 01
p
kilogram square meter, kgm2
2.926397 E 04
p p
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 13
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
13
CONVERSION FACTORS
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued)
2
1
2
2
4 4 1 1 1 4
To convert from
To
Multiply by
pound per foot second, lb/fts pound per square foot, lb/ft2 pound per cubic foot, lb/ft3 pound per gallon, lb/gal (U.K. liquid) pound per gallon, lb/gal (U.S. liquid) pound per hour, lb/h
pascal second, Pas kilogram per square meter, kg/m2 kilogram per cubic meter, kg/m3 kilogram per cubic meter, kg/m3 kilogram per cubic meter, kg/m3 kilogram per second, kg/s kilogram per cubic meter, kg/m3 kilogram per second, kg/s kilogram per second, kg/s kilogram per cubic meter, kg/m3 newton, N newton, N newton meter, Nm newton per meter, N/m pascal, Pa
1.488164 E 00
pound per cubic inch, lb/in3 pound per minute, lb/min pound per second, lb/s pound per cubic yard, lb/yd3 poundal poundforce, lbf pound force foot, lbfft pound force per foot, lbf/ft pound force per square foot, lbf/ft2 pound force per inch, lbf/in
newton per meter, N/m
4.882428 E 00 1.601846 E 01 9.977633 E 01 1.198264 E 02 1.259979 E 04 2.767990 E 04 7.559873 E 03 4.535924 E 01 5.932764 E 01 1.382550 E 01 4.448222 E 00 1.355818 E 00 1.459390 E 01 4.788026 E 01 1.751268 E 02
TLFeBOOK
40816_01_p1-14
10/22/01
12:38 PM
Page 14
40816 HICKS Mcghp Chap_01 Second Pass 7/3/2001
14
CHAPTER ONE
TABLE 1.3 Factors for Conversion to SI Units of Measurement (Continued) To convert from
To
Multiply by
pound force per square inch, lbf/in2 (psi) quart, qt (U.S. dry) quart, qt (U.S. liquid)
pascal, Pa
6.894757 E 03
cubic meter, m3 cubic meter, m3
rod second (angle) second (sidereal) square (100 ft2) ton (assay) ton (long, 2240 lb) ton (metric) ton (refrigeration) ton (register) ton (short, 2000 lb) ton (long per cubic yard, ton)/yd3 ton (short per cubic yard, ton)/yd3 ton force (2000 lbf) tonne, t
meter, m radian, rad second, s square meter, m2 kilogram, kg kilogram, kg kilogram, kg watt, W cubic meter, m3 kilogram, kg kilogram per cubic meter, kg/m3 kilogram per cubic meter, kg/m3 newton, N kilogram, kg
1.101221 9.463529 5.029210 4.848137 9.972696 9.290304† 2.916667 1.016047 1.000000† 3.516800 2.831685 9.071847 1.328939
watt hour, Wh yard, yd square yard, yd2 cubic yard, yd3 year (365 days) year (sidereal)
joule, J meter, m square meter, m2 cubic meter, m3 second, s second, s
E 03 E 04 E 00 E 06 E 01 E 00 E 02 E 03 E 03 E 03 E 00 E 02 E 03
1.186553 E 03 8.896444 E 03 1.000000† E 03 3.600000† E 03 9.144000† E 01 8.361274 E 01 7.645549 E 01 3.153600† E 07 3.155815 E 07
† Exact value. From E380, “Standard for Metric Practice,” American Society for Testing and Materials.
TLFeBOOK
40816_02_p15-51
10/22/01
12:39 PM
40816 HICKS Mcghp Chap_02
Page 15
First Pass 5/23/01 p. 15
CHAPTER 2
BEAM FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_02_p15-51
10/22/01
12:39 PM
40816 HICKS Mcghp Ch02
16
Page 16
Second Pass
pb 7/3/01 p. 16
CHAPTER TWO
In analyzing beams of various types, the geometric properties of a variety of cross-sectional areas are used. Figure 2.1 gives equations for computing area A, moment of inertia I, section modulus or the ratio S I/c, where c distance from the neutral axis to the outermost fiber of the beam or other member. Units used are inches and millimeters and their powers. The formulas in Fig. 2.1 are valid for both USCS and SI units. Handy formulas for some dozen different types of beams are given in Fig. 2.2. In Fig. 2.2, both USCS and SI units can be used in any of the formulas that are applicable to both steel and wooden beams. Note that W load, lb (kN); L length, ft (m); R reaction, lb (kN); V shear, lb (kN); M bending moment, lb ft (N m); D deflection, ft (m); a spacing, ft (m); b spacing, ft (m); E modulus of elasticity, lb/in2 (kPa); I moment of inertia, in4 (dm4); less than; greater than. Figure 2.3 gives the elastic-curve equations for a variety of prismatic beams. In these equations the load is given as P, lb (kN). Spacing is given as k, ft (m) and c, ft (m).
CONTINUOUS BEAMS Continuous beams and frames are statically indeterminate. Bending moments in these beams are functions of the geometry, moments of inertia, loads, spans, and modulus of elasticity of individual members. Figure 2.4 shows how any span of a continuous beam can be treated as a single beam, with the moment diagram decomposed into basic components. Formulas for analysis are given in the diagram. Reactions of a continuous beam can be found by using the formulas in Fig. 2.5. Fixed-end moment formulas for beams of constant moment of inertia (prismatic beams) for TLFeBOOK
408
1 , e r d h f I e b , , y s
. e f y , . e r r
16
10/22/01
12:39 PM Third Pass
Page 17 bcj 7/19/01 p. 17
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
17
FIGURE 2.1 Geometric properties of sections.
40816_02_p15-51
10/22/01 pb 7/3/01 p. 18
Page 18
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
18
TLFeBOOK
408
18
10/22/01
12:39 PM Third Pass
Page 19 bcj 7/19/01 p. 19
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
19
Geometric properties of sections. FIGURE 2.1 (Continued)
40816_02_p15-51
10/22/01 pb 7/3/01 p. 20
Page 20
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
20
TLFeBOOK
408
20
10/22/01
12:39 PM Third Pass
Page 21 bcj 7/19/01 p. 21
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
21
Geometric properties of sections. FIGURE 2.1 (Continued)
40816_02_p15-51
10/22/01 pb 7/3/01 p. 22
Page 22
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
22
TLFeBOOK
408
22
10/22/01
12:39 PM Third Pass
Page 23 bcj 7/19/01 p. 23
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
23
Geometric properties of sections. FIGURE 2.1 (Continued)
40816_02_p15-51
10/22/01 pb 7/3/01 p. 24
Page 24
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
24
TLFeBOOK
408
24
10/22/01
12:39 PM Third Pass
25
Page 25 bcj 7/19/01 p. 25
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
Geometric properties of sections. FIGURE 2.1 (Continued)
10/22/01
12:39 PM pb 7/3/01 p. 26
Page 26
Second Pass
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
26
Geometric properties of sections. FIGURE 2.1 (Continued)
408
s C fi i m i i b g
m b d F b e e b l l m o d s F f l t
40816_02_p15-51 26
10/22/01
12:39 PM
40816 HICKS Mcghp Ch02
Page 27
Third Pass
27
BEAM FORMULAS
p p
bcj 7/19/01 p. 27
several common types of loading are given in Fig. 2.6. Curves (Fig. 2.7) can be used to speed computation of fixed-end moments in prismatic beams. Before the curves in Fig. 2.7 can be used, the characteristics of the loading must be computed by using the formulas in Fig. 2.8. These include xL, the location of the center of gravity of the loading with respect to one of the loads; G2 b 2n Pn/W, where bnL is the distance from each load Pn to the center of gravity of the loading (taken positive to the right); and S 3
b 3n Pn/W. These values are given in Fig. 2.8 for some common types of loading. Formulas for moments due to deflection of a fixed-end beam are given in Fig. 2.9. To use the modified moment distribution method for a fixed-end beam such as that in Fig. 2.9, we must first know the fixed-end moments for a beam with supports at different levels. In Fig. 2.9, the right end of a beam with span L is at a height d above the left end. To find the fixed-end moments, we first deflect the beam with both ends hinged; and then fix the right end, leaving the left end hinged, as in Fig. 2.9b. By noting that a line connecting the two supports makes an angle approximately equal to d/L (its tangent) with the original position of the beam, we apply a moment at the hinged end to produce an end rotation there equal to d/L. By the definition of stiffness, this moment equals that shown at the left end of Fig. 2.9b. The carryover to the right end is shown as the top formula on the right-hand side of Fig. 2.9b. By using the law of reciprocal deflections, we obtain the end moments of the deflected beam in Fig. 2.9 as M FL K FL (1 C FR)
d L
(2.1)
M FR K FR (1 C FL )
d L
(2.2) TLFeBOOK
40816_02_p15-51
10/22/01 pb 7/3/01 p. 28
Page 28
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
28
TLFeBOOK
408
28 10/22/01 12:39 PM
Third Pass
Page 29
bcj 7/19/01 p. 29
TLFeBOOK
40816_02_p15-51
40816 HICKS Mcghp Ch02
29 FIGURE 2.2 Beam formulas. (From J. Callender, Time-Saver Standards for Architectural Design Data, 6th ed., McGraw-Hill, N.Y.)
40816_02_p15-51
10/22/01 pb 7/3/01 p. 30
Page 30
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
30
TLFeBOOK
408
30
10/22/01
12:39 PM Third Pass
Page 31 bcj 7/19/01 p. 31
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
31
Beam formulas. FIGURE 2.2 (Continued)
40816_02_p15-51
10/22/01 pb 7/3/01 p. 32
Page 32
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
32
TLFeBOOK
408
32
10/22/01
12:39 PM Third Pass
Page 33 bcj 7/19/01 p. 33
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
33
Beam formulas. FIGURE 2.2 (Continued)
40816_02_p15-51
10/22/01 pb 7/3/01 p. 34
Page 34
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
34
TLFeBOOK
408
34
10/22/01
12:39 PM Third Pass
Page 35 bcj 7/19/01 p. 35
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
35
Beam formulas. FIGURE 2.2 (Continued)
40816_02_p15-51
10/22/01 pb 7/3/01 p. 36
Page 36
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
36
TLFeBOOK
408
36
10/22/01
12:39 PM Third Pass
Page 37 bcj 7/19/01 p. 37
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
37
Beam formulas. FIGURE 2.2 (Continued)
40816_02_p15-51
10/22/01 pb 7/3/01 p. 38
Page 38
Second Pass
12:39 PM
40816 HICKS Mcghp Ch02
38
TLFeBOOK
408
38
10/22/01
12:39 PM Third Pass
Page 39 bcj 7/19/01 p. 39
TLFeBOOK
40816_02_p15-51 40816 HICKS Mcghp Ch02
39
Beam formulas. FIGURE 2.2 (Continued)
10/22/01 12:39 PM
pb 7/3/01 p. 40
Page 40
Second Pass
TLFeBOOK
40816_02_p15-51
40816 HICKS Mcghp Ch02
40 FIGURE 2.3 Elastic-curve equations for prismatic beams. (a) Shears, moments, deflections for full uniform load on a simply supported prismatic beam. (b) Shears and moments for uniform load over part of a simply supported prismatic beam. (c) Shears, moments, deflections for a concentrated load at any point of a simply supported prismatic beam.
408
40 10/22/01 12:39 PM
Third Pass
Page 41
bcj 7/19/01 p. 41
TLFeBOOK
40816_02_p15-51
40816 HICKS Mcghp Ch02
41 FIGURE 2.3 (Continued) Elastic-curve equations for prismatic beams. (d) Shears, moments, deflections for a concentrated load at midspan of a simply supported prismatic beam. (e) Shears, moments, deflections for two equal concentrated loads on a simply supported prismatic beam. ( f ) Shears, moments, deflections for several equal loads equally spaced on a simply supported prismatic beam.
10/22/01 12:39 PM
pb 7/3/01 p. 42
Page 42
Second Pass
TLFeBOOK
40816_02_p15-51
40816 HICKS Mcghp Ch02
42 FIGURE 2.3 (Continued) Elastic-curve equations for prismatic beams. (g) Shears, moments, deflections for a concentrated load on a beam overhang. (h) Shears, moments, deflections for a concentrated load on the end of a prismatic cantilever. (i) Shears, moments, deflections for a uniform load over the full length of a beam with overhang.
408
42 10/22/01 12:39 PM
Third Pass
Page 43
bcj 7/19/01 p. 43
TLFeBOOK
40816_02_p15-51
40816 HICKS Mcghp Ch02
43 FIGURE 2.3 (Continued) Elastic-curve equations for prismatic beams. (j) Shears, moments, deflections for uniform load over the full length of a cantilever. (k) Shears, moments, deflections for uniform load on a beam overhang. (l) Shears, moments, deflections for triangular loading on a prismatic cantilever.
12:39 PM Page 44
pb 7/3/01 p. 44
TLFeBOOK
10/22/01
Second Pass
Elastic-curve equations for prismatic beams. (m) Simple beam—load increas-
40816_02_p15-51
40816 HICKS Mcghp Ch02
44 FIGURE 2.3 (Continued) ing uniformly to one end.
408
44 12:39 PM Page 45
bcj 7/19/01 p. 45
TLFeBOOK
10/22/01
Third Pass
Elastic-curve equations for prismatic beams. (n) Simple beam—load increas-
40816_02_p15-51
40816 HICKS Mcghp Ch02
45 FIGURE 2.3 (Continued) ing uniformly to center.
10/22/01 12:39 PM
pb 7/3/01 p. 46
Page 46
Second Pass
TLFeBOOK
40816_02_p15-51
40816 HICKS Mcghp Ch02
46 FIGURE 2.3 (Continued) Elastic-curve equations for prismatic beams. (o) Simple beam—uniform load partially distributed at one end.
408
46 12:39 PM Page 47
bcj 7/19/01 p. 47
TLFeBOOK
10/22/01
Third Pass
Elastic-curve equations for prismatic beams. (p) Cantilever beam—concen-
40816_02_p15-51
40816 HICKS Mcghp Ch02
47 FIGURE 2.3 (Continued) trated load at free end.
12:39 PM Page 48
pb 7/3/01 p. 48
TLFeBOOK
10/22/01
Second Pass
Elastic-curve equations for prismatic beams. (q) Beam fixed at both ends—
40816_02_p15-51
40816 HICKS Mcghp Ch02
48 FIGURE 2.3 (Continued) concentrated load at center.
408
48 10/22/01 12:39 PM
Third Pass
Page 49
bcj 7/19/01 p. 49
TLFeBOOK
40816_02_p15-51
40816 HICKS Mcghp Ch02
49 FIGURE 2.4 Any span of a continuous beam (a) can be treated as a simple beam, as shown in (b) and (c). In (c), the moment diagram is decomposed into basic components.
40816_02_p15-51
10/22/01
12:39 PM
40816 HICKS Mcghp Ch02
50
Page 50
Second Pass
pb 7/3/01 p. 50
408
CHAPTER TWO
F c c
I o f FIGURE 2.5 Reactions of continuous beam (a) found by making the beam statically determinate. (b) Deflections computed with interior supports removed. (c), (d ), and (e) Deflections calculated for unit load over each removed support, to obtain equations for each redundant.
TLFeBOOK
w i t
40816_02_p15-51 50
10/22/01
12:39 PM
40816 HICKS Mcghp Ch02
Third Pass
BEAM FORMULAS
Page 51 bcj 7/19/01 p. 51
51
FIGURE 2.6 Fixed-end moments for a prismatic beam. (a) For a concentrated load. (b) For a uniform load. (c) For two equal concentrated loads. (d) For three equal concentrated loads.
In a similar manner the fixed-end moment for a beam with one end hinged and the supports at different levels can be found from g h d r
MF K
d L
(2.3)
where K is the actual stiffness for the end of the beam that is fixed; for beams of variable moment of inertia K equals the fixed-end stiffness times (1 C FL C FR). TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Third Pass
Page 52 7/19/01 bcj p. 52
408
FIGURE 2.7 Chart for fixed-end moments due to any type of loading.
F
C M b u
FIGURE 2.8 Characteristics of loadings. TLFeBOOK
40816_02_p52-98 p. 52
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 53
Second Pass
7/3/01 pb p. 53
BEAM FORMULAS
53
f
FIGURE 2.8 (Continued)
Characteristics of loadings.
ULTIMATE STRENGTH OF CONTINUOUS BEAMS Methods for computing the ultimate strength of continuous beams and frames may be based on two theorems that fix upper and lower limits for load-carrying capacity: 1. Upper-bound theorem. A load computed on the basis of an assumed link mechanism is always greater than, or at best equal to, the ultimate load. TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
54
Third Pass
Page 54 7/19/01 bcj p. 54
408
CHAPTER TWO
p t m t t r
f U t i FIGURE 2.9 Moments due to deflection of a fixed-end beam.
2. Lower-bound theorem. The load corresponding to an equilibrium condition with arbitrarily assumed values for the redundants is smaller than, or at best equal to, the ultimate loading—provided that everywhere moments do not exceed MP. The equilibrium method, based on the lower bound theorem, is usually easier for simple cases. TLFeBOOK
C
o
A k
40816_02_p52-98 p. 54
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 55
Second Pass
7/3/01 pb p. 55
55
BEAM FORMULAS
For the continuous beam in Fig. 2.10, the ratio of the plastic moment for the end spans is k times that for the center span (k 1). Figure 2.10b shows the moment diagram for the beam made determinate by ignoring the moments at B and C and the moment diagram for end moments MB and MC applied to the determinate beam. Then, by using Fig. 2.10c, equilibrium is maintained when MP
1 wL2 1 M M 4 2 B 2 C
wL2 4 kM P
wL2 4(1 k)
(2.4)
The mechanism method can be used to analyze rigid frames of constant section with fixed bases, as in Fig. 2.11. Using this method with the vertical load at midspan equal to 1.5 times the lateral load, the ultimate load for the frame is 4.8MP /L laterally and 7.2M P /L vertically at midspan. Maximum moment occurs in the interior spans AB and CD when x n s e s n e
M L 2 wL
(2.5)
or if M kM P
when
x
L kM P 2 wL
(2.6)
A plastic hinge forms at this point when the moment equals kMP. For equilibrium, TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
56
Third Pass
Page 56 7/19/01 bcj p. 56
CHAPTER TWO
FIGURE 2.10 Continuous beam shown in (a) carries twice as much uniform load in the center span as in the side span. In (b) are shown the moment diagrams for this loading condition with redundants removed and for the redundants. The two moment diagrams are combined in (c), producing peaks at which plastic hinges are assumed to form. TLFeBOOK
408
p. 56
s e s e
10/22/01 12:41 PM
7/3/01 pb p. 57
Page 57
Second Pass
TLFeBOOK
40816_02_p52-98
40816 HICKS Mcghp Ch02
57 FIGURE 2.11 Ultimate-load possibilities for a rigid frame of constant section with fixed bases.
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
58
Page 58
Third Pass
7/19/01 bcj p. 58
408
CHAPTER TWO
kM P
w x x (L x) kM P 2 L w 2
kM 1 kM L2 kMwL L2 KM wL 2 wL P
P
P 2
P
leading to
F
k 2M 2P wL2 3kM P 0 2 wL 4
(2.7)
When the value of MP previously computed is substituted, 7k 2 4k 4
or
k (k 47) 47
from which k 0.523. The ultimate load is wL
4M P (1 k) M 6.1 P L L
(2.8)
s o o s s f m i
In any continuous beam, the bending moment at any section is equal to the bending moment at any other section, plus the shear at that section times its arm, plus the product of all the intervening external forces times their respective arms. Thus, in Fig. 2.12, Vx R 1 R 2 R 3 P1 P2 P3 M x R 1 (l 1 l 2 x) R 2 (l 2 x) R 3x P1 (l 2 c x) P2 (b x) P3a M x M 3 V3x P3a Table 2.1 gives the value of the moment at the various supports of a uniformly loaded continuous beam over equal TLFeBOOK
F a
40816_02_p52-98 p. 58
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 59
Second Pass
BEAM FORMULAS
7/3/01 pb p. 59
59
FIGURE 2.12 Continuous beam.
) ,
)
spans, and it also gives the values of the shears on each side of the supports. Note that the shear is of the opposite sign on either side of the supports and that the sum of the two shears is equal to the reaction. Figure 2.13 shows the relation between the moment and shear diagrams for a uniformly loaded continuous beam of four equal spans. (See Table 2.1.) Table 2.1 also gives the maximum bending moment that occurs between supports, in addition to the position of this moment and the points of
y , t e
s l
FIGURE 2.13 Relation between moment and shear diagrams for a uniformly loaded continuous beam of four equal spans.
TLFeBOOK
(Uniform load per unit length w; length of each span l)
0
1
2
0
0.125
0.500
None
3
1 2
0 5 8
3
8 5 8
0 1 8
0.0703 0.0703
0.375 0.625
0.750 0.250
4
1 2 1
6
5
2 3 1
0 10 0
10 10 11 28
17 13
28 28 0
4
5
1
0 10 0
0.080 0.025 0.0772
0.400 0.500 0.393
0.800 0.276, 0.724 0.786
15
28 28 15 38
3
13
2
28 28 0
0.0364 0.0364 0.0779
0.536 0.464 0.395
0.266, 0.806 0.194, 0.734 0.789
TLFeBOOK
2
23
20
4
0 0332
0 526
0 268 0 783
408
6
Page 60
1 or 2
7/19/01 bcj p. 60
2
12:41 PM
Moment over each support
Third Pass
Notation of support of span
Distance to point of inflection, measured to right from support
10/22/01
60
Number of supports
Shear on each side of support. L left, R right. Reaction at any support is L R L R
Distance to point of max moment, measured to Max right from moment in from each span support
40816_02_p52-98
40816 HICKS Mcghp Ch02
TABLE 2.1 Uniformly Loaded Continuous Beams over Equal Spans
0.0332 0.0461 0.0777 0.0340
0.526 0.500 0.394 0.533
0.268, 0.783 0.196, 0.804 0.788 0.268, 0.790
3 4 1
49
104 104 0
51
104 104 56 142
8
53
9
104 104 0
0.0433 0.0433 0.0778
0.490 0.510 0.394
0.196, 0.785 0.215, 0.804 0.789
2 3 4
86
75
67
70
142 142 71 142
142 142 12 142
0.0338 0.0440 0.0405
0.528 0.493 0.500
0.268, 0.788 0.196, 0.790 0.215, 0.785
wl
wl 2
wl 2
l
l
Values apply to
53
142 142 72 142 wl
19
4 3
15 11
The numerical values given are coefficients of the expressions at the foot of each column.
Page 61
7/3/01 pb p. 61
TLFeBOOK
12:41 PM
38 38 0 11 104
20
Second Pass
61
38 38 41 104 55 104
18
10/22/01
8
38 38 0 63 104 23
40816_02_p52-98
7
2 3 1 2
40816 HICKS Mcghp Ch02
6
p. 60
38
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
62
Third Pass
Page 62 7/19/01 bcj p. 62
408
CHAPTER TWO
t r t r
t w
FIGURE 2.14 Values of the functions for a uniformly loaded continuous beam resting on three equal spans with four supports.
inflection. Figure 2.14 shows the values of the functions for a uniformly loaded continuous beam resting on three equal spans with four supports. Maxwell’s Theorem When a number of loads rest upon a beam, the deflection at any point is equal to the sum of the deflections at this point due to each of the loads taken separately. Maxwell’s theorem states that if unit loads rest upon a beam at two points, A and B, the deflection at A due to the unit load at B equals the deflection at B due to the unit load at A. Castigliano’s Theorem This theorem states that the deflection of the point of application of an external force acting on a beam is equal TLFeBOOK
B B s l M t w a i t s t e i m 2 s a
40816_02_p52-98 p. 62
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 63
Second Pass
BEAM FORMULAS
7/3/01 pb p. 63
63
to the partial derivative of the work of deformation with respect to this force. Thus, if P is the force, f is the deflection, and U is the work of deformation, which equals the resilience: dU f dP According to the principle of least work, the deformation of any structure takes place in such a manner that the work of deformation is a minimum.
d .
r l
t t , s
f l
BEAMS OF UNIFORM STRENGTH Beams of uniform strength so vary in section that the unit stress S remains constant, and I/c varies as M. For rectangular beams of breadth b and depth d, I/c I/c bd 2/6 and M Sbd2/6. For a cantilever beam of rectangular cross section, under a load P, Px Sbd 2/6. If b is constant, d 2 varies with x, and the profile of the shape of the beam is a parabola, as in Fig. 2.15. If d is constant, b varies as x, and the beam is triangular in plan (Fig. 2.16). Shear at the end of a beam necessitates modification of the forms determined earlier. The area required to resist shear is P/Sv in a cantilever and R/Sv in a simple beam. Dotted extensions in Figs. 2.15 and 2.16 show the changes necessary to enable these cantilevers to resist shear. The waste in material and extra cost in fabricating, however, make many of the forms impractical, except for cast iron. Figure 2.17 shows some of the simple sections of uniform strength. In none of these, however, is shear taken into account. TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
64
Third Pass
Page 64 7/19/01 bcj p. 64
408
CHAPTER TWO
FIGURE 2.15 Parabolic beam of uniform strength.
SAFE LOADS FOR BEAMS OF VARIOUS TYPES Table 2.2 gives 32 formulas for computing the approximate safe loads on steel beams of various cross sections for an allowable stress of 16,000 lb/in2 (110.3 MPa). Use these formulas for quick estimation of the safe load for any steel beam you are using in a design. TLFeBOOK
T W p l
40816_02_p52-98 p. 64
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 65
Second Pass
7/3/01 pb p. 65
BEAM FORMULAS
65
FIGURE 2.16 Triangular beam of uniform strength.
e n e l
Table 2.3 gives coefficients for correcting values in Table 2.2 for various methods of support and loading. When combined with Table 2.2, the two sets of formulas provide useful time-saving means of making quick safeload computations in both the office and the field. TLFeBOOK
Solid rectangle
Hollow cylinder
1,780AD L
Load in middle wL3 32AD 2
Load distributed wL3 52AD 2
890(AD ad) L
1,780(AD ad) L
wL3 32(AD 2 ad 2)
wL3 52(AD 2 ad 2)
667AD L
1,333AD L
wL3 24AD 2
wL3 38AD 2
667(AD ad) L
1,333(AD ad) L
wL3 24(AD 2 ad 2)
wL3 38(AD 2 ad 2) TLFeBOOK
1 770AD
L3
L3
408
885AD
Page 66
Solid cylinder
Load distributed
890AD L
7/19/01 bcj p. 66
Hollow rectangle
Load in middle
Third Pass
Shape of section
Deflection, in‡
12:41 PM
66
Greatest safe load, lb‡
10/22/01
(Beams supported at both ends; allowable fiber stress for steel, 16,000 lb/in2 (1.127 kgf/cm2) (basis of table) for iron, reduce values given in table by one-eighth)
40816_02_p52-98
40816 HICKS Mcghp Ch02
TABLE 2.2 Approximate Safe Loads in Pounds (kgf) on Steel Beams*
ad )
ad )
wL3 32AD 2
wL3 52AD 2
Channel or Z bar
1,525AD L
3,050AD L
wL3 53AD 2
wL3 85AD 2
Deck beam
1,380AD L
2,760AD L
wL3 50AD 2
wL3 80AD 2
I beam
1,795AD L
3,390AD L
wL3 58AD 2
wL3 93AD 2
7/3/01 pb p. 67
Page 67
Second Pass
67
TLFeBOOK
12:41 PM
L distance between supports, ft (m); A sectional area of beam, in2 (cm2); D depth of beam, in (cm); a interior area, in2 (cm2); d interior depth, in (cm); w total working load, net tons (kgf).
*
10/22/01
1.770AD L
38(AD
40816_02_p52-98
885AD L
Even-legged angle or tee
24(AD
40816 HICKS Mcghp Ch02
L
p. 66
L
TLFeBOOK
fi d
d
il
408
B
Page 68
0.976 0.96 1.08
12:41 PM
1.0 0.80
7/19/01 bcj p. 68
1.0 1 2 l/4c 0.974 3 4 3 2
Third Pass
Beam supported at ends Load uniformly distributed over span Load concentrated at center of span Two equal loads symmetrically concentrated Load increasing uniformly to one end Load increasing uniformly to center Load decreasing uniformly to center
Max relative safe load
10/22/01
68 Conditions of loading
Max relative deflection under max relative safe load
40816_02_p52-98
40816 HICKS Mcghp Ch02
TABLE 2.3 Coefficients for Correcting Values in Table 2.2 for Various Methods of Support and of Loading†
y
1
2.40 3.20 1.92
Page 69
7/3/01 pb p. 69
TLFeBOOK
12:41 PM
Second Pass
69
l length of beam; c distance from support to nearest concentrated load; a distance from support to end of beam.
†
10/22/01
l2/4a2 l/(l – 4a) 5.83 l/4a
40816_02_p52-98
Beam continuous over two supports equidistant from ends Load uniformly distributed over span 1. If distance a 0.2071l 2. If distance a 0.2071l 3. If distance a 0.2071l Two equal loads concentrated at ends
4 8 3 8
1
40816 HICKS Mcghp Ch02
Beam fixed at one end, cantilever Load uniformly distributed over span Load concentrated at end Load increasing uniformly to fixed end
2
p. 68
g
40816_02_p52-98
10/22/01 Third Pass
12:41 PM
40816 HICKS Mcghp Ch02
70
Page 70 7/19/01 bcj p. 70
TLFeBOOK
408
p. 70
10/22/01
12:41 PM 7/3/01 pb p. 71
Page 71
Second Pass
TLFeBOOK
40816_02_p52-98 40816 HICKS Mcghp Ch02
71
FIGURE 2.17 Beams of uniform strength (in bending).
40816_02_p52-98
10/22/01 Third Pass
12:41 PM
40816 HICKS Mcghp Ch02
72
Page 72 7/19/01 bcj p. 72
TLFeBOOK
408
p. 72
10/22/01
12:41 PM 7/3/01 pb p. 73
Page 73
Second Pass
TLFeBOOK
40816_02_p52-98 40816 HICKS Mcghp Ch02
73
Beams of uniform strength (in bending). FIGURE 2.17 (Continued)
40816_02_p52-98
10/22/01 Third Pass
12:41 PM
40816 HICKS Mcghp Ch02
74
Page 74 7/19/01 bcj p. 74
TLFeBOOK
408
p. 74
10/22/01
12:41 PM 7/3/01 pb p. 75
Page 75
Second Pass
TLFeBOOK
40816_02_p52-98 40816 HICKS Mcghp Ch02
75
Beams of uniform strength (in bending). FIGURE 2.17 (Continued)
40816_02_p52-98
10/22/01 Third Pass
12:41 PM
40816 HICKS Mcghp Ch02
76
Page 76 7/19/01 bcj p. 76
TLFeBOOK
408
p. 76
10/22/01
12:41 PM 7/3/01 pb p. 77
Page 77
Second Pass
TLFeBOOK
40816_02_p52-98 40816 HICKS Mcghp Ch02
77
Beams of uniform strength (in bending). FIGURE 2.17 (Continued)
10/22/01
12:41 PM Third Pass
Page 78 7/19/01 bcj p. 78
TLFeBOOK
40816_02_p52-98 40816 HICKS Mcghp Ch02
78
Beams of uniform strength (in bending). FIGURE 2.17 (Continued)
408
R R p w w b s m
a b
40816_02_p52-98 p. 78
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 79
Second Pass
7/3/01 pb p. 79
79
BEAM FORMULAS
ROLLING AND MOVING LOADS Rolling and moving loads are loads that may change their position on a beam or beams. Figure 2.18 shows a beam with two equal concentrated moving loads, such as two wheels on a crane girder, or the wheels of a truck on a bridge. Because the maximum moment occurs where the shear is zero, the shear diagram shows that the maximum moment occurs under a wheel. Thus, with x a/2:
R1 P 1 M2
Pl a 2x a 4x 2 1 2 2 l l l l
R2 P 1
M1
2x a l l
Pl 2
2x a l l
1 al 2al
2
2
2x 3a 4x 2 2 l l l
M2 max when x 14a M1 max when x 34a M max
Pl 2
1 2la 2lP l 2a 2
2
Figure 2.19 shows the condition when two equal loads are equally distant on opposite sides of the center of the beam. The moment is then equal under the two loads. TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Third Pass
Page 80 7/19/01 bcj p. 80
408
t r b t s b t p
FIGURE 2.18 Two equal concentrated moving loads.
FIGURE 2.19 Two equal moving loads equally distant on opposite sides of the center. 80 TLFeBOOK
F
40816_02_p52-98 p. 80
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 81
Second Pass
7/3/01 pb p. 81
BEAM FORMULAS
81
If two moving loads are of unequal weight, the condition for maximum moment is the maximum moment occurring under the heavier wheel when the center of the beam bisects the distance between the resultant of the loads and the heavier wheel. Figure 2.20 shows this position and the shear and moment diagrams. When several wheel loads constituting a system are on a beam or beams, the several wheels must be examined in turn to determine which causes the greatest moment. The position for the greatest moment that can occur under a given
FIGURE 2.20
Two moving loads of unequal weight. TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
82
Page 82
Third Pass
7/19/01 bcj p. 82
408
CHAPTER TWO
wheel is, as stated earlier, when the center of the span bisects the distance between the wheel in question and the resultant of all loads then on the span. The position for maximum shear at the support is when one wheel is passing off the span.
CURVED BEAMS The application of the flexure formula for a straight beam to the case of a curved beam results in error. When all “fibers” of a member have the same center of curvature, the concentric or common type of curved beam exists (Fig. 2.21). Such a beam is defined by the Winkler–Bach theory. The stress at a point y units from the centroidal axis is
M is the bending moment, positive when it increases curvature; y is positive when measured toward the convex side; A is the cross-sectional area; R is the radius of the centroidal axis; Z is a cross-section property defined by Z
1 A
y dA Ry
Analytical expressions for Z of certain sections are given in Table 2.4. Z can also be found by graphical integration methods (see any advanced strength book). The neutral surface shifts toward the center of curvature, or inside fiber, an amount equal to e ZR/(Z 1). The Winkler–Bach TLFeBOOK
f
Z
1 Z (Ry y)
i
M AR
TABLE 2 4 A l i l E
S
p. 82
n e f
m l , s h l
A l
n n l , h Section
Expression R h
2
7/3/01 pb p. 83
R C2 R b ln A R C2 A 2 [(t b)C1 bC2] Z 1
(t b) ln RR CC 1 1
TLFeBOOK
Page 83
R t ln (R C1) (b t) ln (R C0) b ln (R C2) A and A tC1 (b t) C3 bC2 Z 1
Second Pass
83
Rr Rr √ Rr 1
12:41 PM
Z 1 2
ln RR CC
10/22/01
Z 1
40816_02_p52-98
40816 HICKS Mcghp Ch02
TABLE 2.4 Analytical Expressions for Z
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
84
Third Pass
Page 84 7/19/01 bcj p. 84
408
CHAPTER TWO
B
FIGURE 2.21 Curved beam.
theory, though practically satisfactory, disregards radial stresses as well as lateral deformations and assumes pure bending. The maximum stress occurring on the inside fiber is S Mhi /AeRi, whereas that on the outside fiber is S Mh0 /AeR0. The deflection in curved beams can be computed by means of the moment-area theory. The resultant deflection is then equal to 0 √ 2x 2y in the direction defined by tan y / x. Deflections can also be found conveniently by use of Castigliano’s theorem. It states that in an elastic system the displacement in the direction of a force (or couple) and due to that force (or couple) is the partial derivative of the strain energy with respect to the force (or couple). A quadrant of radius R is fixed at one end as shown in Fig. 2.22. The force F is applied in the radial direction at free-end B. Then, the deflection of B is TLFeBOOK
B
F
40816_02_p52-98 p. 84
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 85
Second Pass
7/3/01 pb p. 85
85
BEAM FORMULAS
By moment area, y R sin ds Rd B x
x R(1 cos )
M FR sin
FR 3 4EI
and B
FR3 2EI
√
1
x tan 1
at
tan 1 l e r
B y
FR 3 2EI
2 4
FR 3 4EI 2EI
FR 3
2
32.5 By Castigliano, B x
y
FR3 4EI
B y
FR3 2EI
2 y
n . e t n t FIGURE 2.22
Quadrant with fixed end. TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
86
Third Pass
Page 86 7/19/01 bcj p. 86
4
CHAPTER TWO
Eccentrically Curved Beams
T
These beams (Fig. 2.23) are bounded by arcs having different centers of curvature. In addition, it is possible for either radius to be the larger one. The one in which the section depth shortens as the central section is approached may be called the arch beam. When the central section is the largest, the beam is of the crescent type. Crescent I denotes the beam of larger outside radius and crescent II of larger inside radius. The stress at the central section of such beams may be found from S KMC/I. In the case of rectangular cross section, the equation becomes S 6KM/bh2, where M is the bending moment, b is the width of the beam section, and h its height. The stress factors, K for the inner boundary, established from photoelastic data, are given in Table 2.5. The outside radius
( 1
2
3
i c c a
FIGURE 2.23 Eccentrically curved beams. TLFeBOOK
40816_02_p52-98 p. 86
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 87
Second Pass
7/3/01 pb p. 87
87
BEAM FORMULAS
TABLE 2.5 Stress Factors for Inner Boundary at Central Section
r n e e d l I. n b s s
(see Fig. 2.23) 1. For the arch-type beams h Ro Ri
(a) K 0.834 1.504
if
Ro Ri 5 h
h R Ri if 5 o 10 Ro Ri h (c) In the case of larger section ratios use the equivalent beam solution 2. For the crescent I-type beams (b) K 0.899 1.181
(a) K 0.570 1.536
h Ro Ri
if
Ro Ri 2 h
(b) K 0.959 0.769
h Ro Ri
if
2
(c) K 1.092
R h R
Ro Ri 20 h
0.0298
o
Ro Ri 20 h
if
i
3. For the crescent II-type beams h Ro Ri
(a) K 0.897 1.098
if
Ro Ri 8 h
(b) K 1.119
R h R
if
8
(c) K 1.081
if
Ro Ri 20 h
0.0378
o
i
h Ro Ri
0.0270
Ro Ri 20 h
is denoted by Ro and the inside by Ri. The geometry of crescent beams is such that the stress can be larger in offcenter sections. The stress at the central section determined above must then be multiplied by the position factor k, TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
88
Page 88
Third Pass
7/19/01 bcj p. 88
CHAPTER TWO
given in Table 2.6. As in the concentric beam, the neutral surface shifts slightly toward the inner boundary. (See Vidosic, “Curved Beams with Eccentric Boundaries,” Transactions of the ASME, 79, pp. 1317–1321.)
When lateral buckling of a beam occurs, the beam undergoes a combination of twist and out-of-plane bending (Fig. 2.24). For a simply supported beam of rectangular cross section subjected to uniform bending, buckling occurs at the critical bending moment, given by Mcr
L
w s m f
ELASTIC LATERAL BUCKLING OF BEAMS
where
408
T ( A
√EIyGJ
L unbraced length of the member E modulus of elasticity Iy moment of inertial about minor axis G shear modulus of elasticity J torsional constant
The critical moment is proportional to both the lateral bending stiffness EIy /L and the torsional stiffness of the member GJ/L. For the case of an open section, such as a wide-flange or I-beam section, warping rigidity can provide additional torsional stiffness. Buckling of a simply supported beam of open cross section subjected to uniform bending occurs at the critical bending moment, given by TLFeBOOK
†
b b
40816_02_p52-98 p. 88
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 89
Second Pass
7/3/01 pb p. 89
89
BEAM FORMULAS
l e ”
Mcr
L
√
EIy GJ ECw
2 L2
where Cw is the warping constant, a function of crosssectional shape and dimensions (Fig. 2.25). In the preceding equations, the distribution of bending moment is assumed to be uniform. For the case of a nonuniform bending-moment gradient, buckling often occurs at g r s
TABLE 2.6 Crescent-Beam Position Stress Factors (see Fig. 2.23)† Angle , degree 10 20 30 40 50 60 70
l e r n e
80 90
k Inner 1 0.055 H/h 1 0.164 H/h 1 0.365 H / h 1 0.567 H / h (0.5171 1.382 H/h)1/2 1.521 1.382 (0.2416 0.6506 H/h)1/2 1.756 0.6506 (0.4817 1.298 H/h)1/2 2.070 0.6492 (0.2939 0.7084 H/h)1/2 2.531 0.3542
Outer 1 0.03 H/h 1 0.10 H/h 1 0.25 H/h 1 0.467 H/h 1 0.733 H/h 1 1.123 H/h 1 1.70 H/h 1 2.383 H/h 1 3.933 H/h
Note: All formulas are valid for 0 H/h 0.325. Formulas for the inner boundary, except for 40 degrees, may be used to H/h 0.36. H distance between centers.
†
TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
90
Third Pass
Page 90 7/19/01 bcj p. 90
408
CHAPTER TWO
F A I Y FIGURE 2.24 (a) Simple beam subjected to equal end moments. (b) Elastic lateral buckling of the beam.
a larger critical moment. Approximation of this critical bending moment, Mcr may be obtained by multiplying Mcr given by the previous equations by an amplification factor M cr Cb Mcr where Cb
12.5Mmax 2.5Mmax 3MA 4MB 3MC TLFeBOOK
a
40816_02_p52-98 p. 90
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 91
Second Pass
BEAM FORMULAS
7/3/01 pb p. 91
91
FIGURE 2.25 Torsion-bending constants for torsional buckling. A cross-sectional area; Ix moment of inertia about x–x axis; Iy moment of inertia about y–y axis. (After McGraw-Hill, New York). Bleich, F., Buckling Strength of Metal Structures. s.
and l r
r
Mmax absolute value of maximum moment in the unbraced beam segment MA absolute value of moment at quarter point of the unbraced beam segment MB absolute value of moment at centerline of the unbraced beam segment MC absolute value of moment at three-quarter point of the unbraced beam segment TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
92
Page 92
Third Pass
7/19/01 bcj p. 92
408
CHAPTER TWO
Cb equals 1.0 for unbraced cantilevers and for members where the moment within a significant portion of the unbraced segment is greater than, or equal to, the larger of the segment end moments.
COMBINED AXIAL AND BENDING LOADS For short beams, subjected to both transverse and axial loads, the stresses are given by the principle of superposition if the deflection due to bending may be neglected without serious error. That is, the total stress is given with sufficient accuracy at any section by the sum of the axial stress and the bending stresses. The maximum stress, lb/in2 (MPa), equals
w s a o a
w (
U
P Mc f A I where P axial load, lb (N) A cross-sectional area, in2 (mm2) M maximum bending moment, in lb (Nm) c distance from neutral axis to outermost fiber at the section where maximum moment occurs, in (mm) I moment of inertia about neutral axis at that section, in4 (mm4) When the deflection due to bending is large and the axial load produces bending stresses that cannot be neglected, the maximum stress is given by TLFeBOOK
W c m t a p p
w
40816_02_p52-98 p. 92
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 93
Second Pass
7/3/01 pb p. 93
93
BEAM FORMULAS
s e f
l n t t d ,
f
P c (M Pd) A I
where d is the deflection of the beam. For axial compression, the moment Pd should be given the same sign as M; and for tension, the opposite sign, but the minimum value of M Pd is zero. The deflection d for axial compression and bending can be closely approximated by d
do 1 (P/Pc)
where do deflection for the transverse loading alone, in (mm); and Pc critical buckling load 2EI / L2, lb (N).
UNSYMMETRICAL BENDING
t ,
When a beam is subjected to loads that do not lie in a plane containing a principal axis of each cross section, unsymmetrical bending occurs. Assuming that the bending axis of the beam lies in the plane of the loads, to preclude torsion, and that the loads are perpendicular to the bending axis, to preclude axial components, the stress, lb/in2 (MPa), at any point in a cross section is f
t where e -
Mx y M x y Ix Iy
Mx bending moment about principal axis XX, in lb (Nm) My bending moment about principal axis YY, in lb (Nm) TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
94
Third Pass
Page 94 7/19/01 bcj p. 94
408
CHAPTER TWO
x distance from point where stress is to be computed to YY axis, in (mm) y distance from point to XX axis, in (mm) Ix moment of inertia of cross section about XX, in (mm4) Iy moment of inertia about YY, in (mm4) If the plane of the loads makes an angle with a principal plane, the neutral surface forms an angle with the other principal plane such that tan
Ix tan Iy
F c a s f n s D t s m t
ECCENTRIC LOADING If an eccentric longitudinal load is applied to a bar in the plane of symmetry, it produces a bending moment Pe, where e is the distance, in (mm), of the load P from the centroidal axis. The total unit stress is the sum of this moment and the stress due to P applied as an axial load: f
P Pec P A I A
P o a (
1 ecr 2
where A cross-sectional area, in2 (mm2)
w
c distance from neutral axis to outermost fiber, in (mm) TLFeBOOK
40816_02_p52-98 p. 94
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
Page 95
Second Pass
7/3/01 pb p. 95
BEAM FORMULAS
95
I moment of inertia of cross section about neutral axis, in4 (mm4) r radius of gyration √I/A, in (mm)
l r
Figure 2.1 gives values of the radius of gyration for several cross sections. If there is to be no tension on the cross section under a compressive load, e should not exceed r 2/c. For a rectangular section with width b, and depth d, the eccentricity, therefore, should be less than b/6 and d/6 (i.e., the load should not be applied outside the middle third). For a circular cross section with diameter D, the eccentricity should not exceed D/8. When the eccentric longitudinal load produces a deflection too large to be neglected in computing the bending stress, account must be taken of the additional bending moment Pd, where d is the deflection, in (mm). This deflection may be closely approximated by d
e , e s
4eP/Pc
(1 P/Pc)
Pc is the critical buckling load 2EI/L2, lb (N). If the load P, does not lie in a plane containing an axis of symmetry, it produces bending about the two principal axes through the centroid of the section. The stresses, lb/in2 (MPa), are given by f
P Pexcx Peycy A Iy Ix
where A cross-sectional area, in2 (mm2) n
ex eccentricity with respect to principal axis YY, in (mm) TLFeBOOK
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
96
Third Pass
Page 96 7/19/01 bcj p. 96
CHAPTER TWO
ey eccentricity with respect to principal axis XX, in (mm) cx distance from YY to outermost fiber, in (mm) cy distance from XX to outermost fiber, in (mm) Ix moment of inertia about XX, in4 (mm4) Iy moment of inertia about YY, in4 (mm4) The principal axes are the two perpendicular axes through the centroid for which the moments of inertia are a maximum or a minimum and for which the products of inertia are zero.
NATURAL CIRCULAR FREQUENCIES AND NATURAL PERIODS OF VIBRATION OF PRISMATIC BEAMS Figure 2.26 shows the characteristic shape and gives constants for determination of natural circular frequency and natural period T, for the first four modes of cantilever, simply supported, fixed-end, and fixed-hinged beams. To obtain , select the appropriate constant from Fig. 2.26 and multiply it by √EI/wL4. To get T, divide the appropriate constant by √EI/wL4. In these equations, natural frequency, rad/s W beam weight, lb per linear ft (kg per linear m) L beam length, ft (m) TLFeBOOK
408
p. 96
,
)
)
h a
d , o d e
10/22/01 12:41 PM
7/3/01 pb p. 97
Page 97
Second Pass
TLFeBOOK
40816_02_p52-98
40816 HICKS Mcghp Ch02
97 FIGURE 2.26 Coefficients for computing natural circular frequencies and natural periods of vibration of prismatic beams.
40816_02_p52-98
10/22/01
12:41 PM
40816 HICKS Mcghp Ch02
98
Third Pass
Page 98 7/19/01 bcj p. 98
CHAPTER TWO
E modulus of elasticity, lb/in2 (MPa) I moment of inertia of beam cross section, in4 (mm4) T natural period, s To determine the characteristic shapes and natural periods for beams with variable cross section and mass, use the Rayleigh method. Convert the beam into a lumped-mass system by dividing the span into elements and assuming the mass of each element to be concentrated at its center. Also, compute all quantities, such as deflection and bending moment, at the center of each element. Start with an assumed characteristic shape. ]
TLFeBOOK
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
12:42 PM
Page 99
SECOND PASS 7/5/01 pb p. 99
CHAPTER 3
COLUMN FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
100
12:42 PM
Page 100
SECOND PASS 7/5/01 pb p. 100
40816
CHAPTER THREE
GENERAL CONSIDERATIONS
1. Compression blocks are so short (with a slenderness ratio — that is, unsupported length divided by the least radius of gyration of the member — below 30) that bending is not potentially occurring. 2. Columns so slender that bending under load is a given are termed long columns and are defined by Euler’s theory. 3. Intermediate-length columns, often used in structural practice, are called short columns. Long and short columns usually fail by buckling when their critical load is reached. Long columns are analyzed using Euler’s column formula, namely, Pcr
n 2EI n 2EA 2 l (l/r)2
In this formula, the coefficient n accounts for end conditions. When the column is pivoted at both ends, n 1; when one end is fixed and the other end is rounded, n 2; when both ends are fixed, n 4; and when one end is fixed and the other is free, n 0.25. The slenderness ratio separating long columns from short columns depends on the modulus of elasticity and the yield strength of the column material. When Euler’s formula results in (Pcr /A) > Sy, strength instead of buckling causes failure, and the column ceases to be long. In quick estimating numbers, this critical slenderness ratio falls between 120 and 150. Table 3.1 gives additional column data based on Euler’s formula. TLFeBOOK
TABLE 3 1 Strength of Round-Ended Columns According to Euler’s Formula*
Columns are structural members subjected to direct compression. All columns can be grouped into the following three classes:
g
s t -
e . l
n d
; ; d e n , n l s
p. 100
Cast iron
62,600
89,000
7,100 14,200,000 8 Pl 2 17,500,000 50.0
15,400 28,400,000 5 Pl 2 56,000,000 60.6
17,000 30,600,000 5 Pl 2 60,300,000 59.4
20,000 31,300,000 5 Pl 2 61,700,000 55.6
Rectangle r b√112 , l/b
14.4
17.5
17.2
16.0
Circle r 14 d, l/d Circular ring of small thickness
12.5
15.2
14.9
13.9
17.6
21.4
21.1
19.7
Limit of ratio, l/r
r d √ , l/d 1
8
(P allowable load, lb; l length of column, in; b smallest dimension of a rectangular section, in; d diameter of a circular section, in; r least radius of gyration of section.) To convert to SI units, use: 1b/in2 6.894 kPa; in4 (25.4)4 mm4.
*
†
TLFeBOOK
Page 101
53,400
12:42 PM
107,000
SECOND PASS 7/5/01 pb p. 101
101
Ultimate compressive strength, lb/in Allowable compressive stress, lb/in2 (maximum) Modulus of elasticity Factor of safety Smallest I allowable at worst section, in4
Mediumcarbon steel
10/22/01
2
Lowcarbon steel
40816_03_p99-130
Material†
Wrought iron
40816 HICKS Mcghp Chap_03
TABLE 3.1 Strength of Round-Ended Columns According to Euler’s Formula*
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
102
12:42 PM
Page 102
SECOND PASS 7/5/01 pb p. 102
CHAPTER THREE
FIGURE 3.1 L/r plot for columns.
SHORT COLUMNS Stress in short columns can be considered to be partly due to compression and partly due to bending. Empirical, rational expressions for column stress are, in general, based on the assumption that the permissible stress must be reduced below that which could be permitted were it due to compression only. The manner in which this reduction is made determines the type of equation and the slenderness ratio beyond which the equation does not apply. Figure 3.1 shows the curves for this situation. Typical column formulas are given in Table 3.2.
ECCENTRIC LOADS ON COLUMNS When short blocks are loaded eccentrically in compression or in tension, that is, not through the center of gravity (cg), a combination of axial and bending stress results. The maximum unit stress SM is the algebraic sum of these two unit stresses. TLFeBOOK
40816
o l e w n s h r .
n , e o
p. 102
Material
Code
Slenderness ratio
Chicago
l 120 r
w
Carbon steels
AREA
l 150 r
w
Carbon steels
Am. Br. Co.
60
Alloy-steel tubing
ANC
Cast iron
NYC
103
2
†
cr
w
l 120 r
l 65 √cr l 70 r
TLFeBOOK
Page 103
Carbon steels
rl l S 15,000 50 r l S 19,000 100 r 15.9 l S 135,000 c r l S 9,000 40 r Sw 16,000 70
12:42 PM
l 120 r
10/22/01
AISC
2
SECOND PASS 7/5/01 pb p. 103
Carbon steels
Sw 17,000 0.485
l r
40816_03_p99-130
Formula
40816 HICKS Mcghp Chap_03
TABLE 3.2 Typical Short-Column Formulas
†
Scr 34,500 Scr 5,000
Scr
rl
2
Sy 4n 2E Sy
l r
Spruce
ANC
1 √cr 1 √cr
rl 2
√ P 4AE
Steels
Johnson
Steels
Secant
94 72
2n 2E l r Sy l critical r
√
Scr theoretical maximum; c end fixity coefficient; c 2, both ends pivoted; c 2.86, one pivoted, other fixed; c 4, both ends fixed; c 1 one fixed, one free. ‡ is initial eccentricity at which load is applied to center of column cross section. †
TLFeBOOK
Page 104
ec 1 2 sec r
ANC
12:42 PM
‡
0.5 c
2017ST aluminum
Slenderness ratio
SECOND PASS 7/5/01 pb p. 104
104
Scr Sy 1
†
√c
Code
10/22/01
†
Material l r
245
40816_03_p99-130
Formula
40816 HICKS Mcghp Chap_03
TABLE 3.2 Typical Short-Column Formulas (Continued)
40816
F
d a t a
y t
40816_03_p99-130 p. 104
10/22/01
40816 HICKS Mcghp Chap_03
12:42 PM
Page 105
SECOND PASS 7/5/01 pb p. 105
COLUMN FORMULAS
105
FIGURE 3.2 Load plot for columns.
In Fig. 3.2, a load, P, acts in a line of symmetry at the distance e from cg; r radius of gyration. The unit stresses are (1) Sc, due to P, as if it acted through cg, and (2) Sb, due to the bending moment of P acting with a leverage of e about cg. Thus, unit stress, S, at any point y is S Sc Sb (P/A) Pey/I Sc(1 ey/r 2) y is positive for points on the same side of cg as P, and negative on the opposite side. For a rectangular cross section of TLFeBOOK
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
106
12:42 PM
Page 106
SECOND PASS 7/5/01 pb p. 106
40816
CHAPTER THREE
width b, the maximum stress, SM Sc (1 6e/b). When P is outside the middle third of width b and is a compressive load, tensile stresses occur. For a circular cross section of diameter d, SM Sc(1 8e/d). The stress due to the weight of the solid modifies these relations. Note that in these formulas e is measured from the gravity axis and gives tension when e is greater than one-sixth the width (measured in the same direction as e), for rectangular sections, and when greater than one-eighth the diameter, for solid circular sections.
FIGURE 3.3 Load plot for columns.
m s t t 3 0 f p t ( a
F TLFeBOOK
40816_03_p99-130 p. 106
10/22/01
40816 HICKS Mcghp Chap_03
12:42 PM
SECOND PASS 7/5/01 pb p. 107
COLUMN FORMULAS
P e s h -
Page 107
107
If, as in certain classes of masonry construction, the material cannot withstand tensile stress and, thus, no tension can occur, the center of moments (Fig. 3.3) is taken at the center of stress. For a rectangular section, P acts at distance k from the nearest edge. Length under compression 2 3k, and SM 3P/hk. For a circular section, SM [0.372 0.056(k/r)]P/k √rk , where r radius and k distance of P from circumference. For a circular ring, S average compressive stress on cross section produced by P; e eccentricity of P; z length of diameter under compression (Fig. 3.4). Values of z/r and of the ratio of Smax to average S are given in Tables 3.3 and 3.4.
FIGURE 3.4 Circular column load plot. TLFeBOOK
(See Fig. 3.5) r1 r
1.89 1.75 1.61
1.98 1.84 1.71
1.93 1.81
1.90
0.50 0.55 0.60 0.65 0.70
1.23 1.10 0.97 0.84 0.72
1.46 1.29 1.12 0.94 0.75
1.56 1.39 1.21 1.02 0.82
1.66 1.50 1.32 1.13 0.93
1.78 1.62 1.45 1.25 1.05
1.89 1.74 1.58 1.40 1.20
2.00 1.87 1.71 1.54 1.35
0.50 0.55 0.60 0.65 0.70
0.75 0.80 0.85 0.90 0.95
0.59 0.47 0.35 0.24 0.12
0.60 0.47 0.35 0.24 0.12
0.64 0.48 0.35 0.24 0.12
0.72 0.52 0.36 0.24 0.12
0.85 0.61 0.42 0.24 0.12
0.99 0.77 0.55 0.32 0.12
1.15 0.94 0.72 0.49 0.25
0.75 0.80 0.85 0.90 0.95
0.7
0.8
0.9
1.0
e r 0.25 0.30 0.35 0.40 0.45
TLFeBOOK
Page 108
2.00 1.82 1.66 1.51 1.37
0.6
12:42 PM
0.25 0.30 0.35 0.40 0.45
0.5
10/22/01
0.0
SECOND PASS 7/5/01 pb p. 108
108
e r
40816_03_p99-130
40816 HICKS Mcghp Chap_03
TABLE 3.3 Values of the Ratio z/r
40816
p. 108
0.6
0.7
0.8
0.9
1.0
e r
0.00 0.05 0.10 0.15 0.20
1.00 1.20 1.40 1.60 1.80
1.00 1.16 1.32 1.48 1.64
1.00 1.15 1.29 1.44 1.59
1.00 1.13 1.27 1.40 1.54
1.00 1.12 1.24 1.37 1.49
1.00 1.11 1.22 1.33 1.44
1.00 1.10 1.20 1.30 1.40
0.00 0.05 0.10 0.15 0.20
0.25 0.30 0.35 0.40 0.45
2.00 2.23 2.48 2.76 3.11
1.80 1.96 2.12 2.29 2.51
1.73 1.88 2.04 2.20 2.39
1.67 1.81 1.94 2.07 2.23
1.61 1.73 1.85 1.98 2.10
1.55 1.66 1.77 1.88 1.99
1.50 1.60 1.70 1.80 1.90
0.25 0.30 0.35 0.40 0.45
TLFeBOOK
Page 109
0.5
12:42 PM
0.0
SECOND PASS 7/5/01 pb p. 109
109
e r
10/22/01
r1 r
40816_03_p99-130
(In determining S average, use load P divided by total area of cross section)
40816 HICKS Mcghp Chap_03
TABLE 3.4 Values of the Ratio Smax/Savg
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
110
12:42 PM
Page 110
SECOND PASS 7/5/01 pb p. 110
40816
CHAPTER THREE
The kern is the area around the center of gravity of a cross section within which any load applied produces stress of only one sign throughout the entire cross section. Outside the kern, a load produces stresses of different sign. Figure 3.5 shows kerns (shaded) for various sections. For a circular ring, the radius of the kern r D[1(d/D)2]/8. For a hollow square (H and h lengths of outer and inner sides), the kern is a square similar to Fig. 3.5a, where
c 0 w
C B a t T u t
w
t 1
FIGURE 3.5 Column characteristics. TLFeBOOK
40816_03_p99-130 p. 110
10/22/01
12:42 PM
40816 HICKS Mcghp Chap_03
Page 111
SECOND PASS 7/5/01 pb p. 111
111
COLUMN FORMULAS
f s s f s
rmin
H 1 6 √2
1 Hh 0.1179H 1 Hh 2
2
For a hollow octagon, Ra and Ri radii of circles circumscribing the outer and inner sides; thickness of wall 0.9239(Ra – Ri); and the kern is an octagon similar to Fig. 3.5c, where 0.2256R becomes 0.2256Ra[1 (Ri /Ra)2].
d e
COLUMN BASE PLATE DESIGN Base plates are usually used to distribute column loads over a large enough area of supporting concrete construction that the design bearing strength of the concrete is not exceeded. The factored load, Pu, is considered to be uniformly distributed under a base plate. The nominal bearing strength fp kip/in2 or ksi (MPa) of the concrete is given by fp 0.85f c where
√
A1 A1
and
√
A2 2 A1
f c specified compressive strength of concrete,
ksi (MPa) A1 area of the base plate, in2 (mm2) A2 area of the supporting concrete that is geometrically similar to and concentric with the loaded area, in2 (mm2) In most cases, the bearing strength, fp is 0.85f c, when the concrete support is slightly larger than the base plate or 1.7f c, when the support is a spread footing, pile cap, or mat TLFeBOOK
40816_03_p99-130
10/22/01
12:42 PM
40816 HICKS Mcghp Chap_03
112
Page 112
SECOND PASS 7/5/01 pb p. 112
40816
CHAPTER THREE
foundation. Therefore, the required area of a base plate for a factored load Pu is A1
Pu c0.85 fc
where c is the strength reduction factor 0.6. For a wideflange column, A1 should not be less than bf d, where bf is the flange width, in (mm), and d is the depth of column, in (mm). The length N, in (mm), of a rectangular base plate for a wide-flange column may be taken in the direction of d as N √A1 d
0.5(0.95d 0.80bf)
or
The width B, in (mm), parallel to the flanges, then, is B
A1 N
The thickness of the base plate tp, in (mm), is the largest of the values given by the equations that follow: tp m tp n
where
T a m
2Pu 0.9Fy BN
√ √ √
t p n
A C D
w p
2Pu 0.9Fy BN
i c t s t i c
2Pu 0.9Fy BN
m projection of base plate beyond the flange and parallel to the web, in (mm) (N 0.95d)/2 TLFeBOOK
40816_03_p99-130 p. 112
10/22/01
12:42 PM
40816 HICKS Mcghp Chap_03
Page 113
SECOND PASS 7/5/01 pb p. 113
COLUMN FORMULAS
r
113
n projection of base plate beyond the edges of the flange and perpendicular to the web, in (mm) (B 0.80bf)/2 n √(dbf)/4
s ,
(2√X)/[1 √(1 X)] 1.0 X [(4 dbf)/(d bf)2][Pu/( 0.85fc 1)]
a
AMERICAN INSTITUTE OF STEEL CONSTRUCTION ALLOWABLE-STRESS DESIGN APPROACH
t
The lowest columns of a structure usually are supported on a concrete foundation. The area, in square inches (square millimeters), required is found from: A
P FP
where P is the load, kip (N) and Fp is the allowable bearing pressure on support, ksi (MPa). The allowable pressure depends on strength of concrete in the foundation and relative sizes of base plate and concrete support area. If the base plate occupies the full area of the support, Fp 0.35f c, where f c is the 28-day compressive strength of the concrete. If the base plate covers less than the full area, FP 0.35fc √A2/A1 0.70f c , where A1 is the base-plate area (B N), and A2 is the full area of the concrete support. TLFeBOOK
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
114
12:42 PM
Page 114
SECOND PASS 7/5/01 pb p. 114
40816
CHAPTER THREE
Eccentricity of loading or presence of bending moment at the column base increases the pressure on some parts of the base plate and decreases it on other parts. To compute these effects, the base plate may be assumed completely rigid so that the pressure variation on the concrete is linear. Plate thickness may be determined by treating projections m and n of the base plate beyond the column as cantilevers.
T s b b t t
w
c p s t
C T f d t c
FIGURE 3.6 Column welded to a base plate.
TLFeBOOK
40816_03_p99-130 p. 114
10/22/01
40816 HICKS Mcghp Chap_03
12:42 PM
Page 115
SECOND PASS 7/5/01 pb p. 115
COLUMN FORMULAS
t s e
115
The cantilever dimensions m and n are usually defined as shown in Fig. 3.6. (If the base plate is small, the area of the base plate inside the column profile should be treated as a beam.) Yield-line analysis shows that an equivalent cantilever dimension n can be defined as n 14√dbf , and the required base plate thickness tp can be calculated from
s . tp 2l
√
fp Fy
where l max (m, n, n), in (mm) fp P/(BN) Fp, ksi (MPa) Fy yield strength of base plate, ksi (MPa) P column axial load, kip (N) For columns subjected only to direct load, the welds of column to base plate, as shown in Fig. 3.6, are required principally for withstanding erection stresses. For columns subjected to uplift, the welds must be proportioned to resist the forces.
COMPOSITE COLUMNS The AISC load-and-resistance factor design (LRFD) specification for structural steel buildings contains provisions for design of concrete-encased compression members. It sets the following requirements for qualification as a composite column: The cross-sectional area of the steel core—shapes, TLFeBOOK
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
116
12:42 PM
Page 116
SECOND PASS 7/5/01 pb p. 116
40816
CHAPTER THREE
pipe, or tubing—should be at least 4 percent of the total composite area. The concrete should be reinforced with longitudinal load-carrying bars, continuous at framed levels, and lateral ties and other longitudinal bars to restrain the concrete; all should have at least 1 12 in (38.1 mm) of clear concrete cover. The cross-sectional area of transverse and longitudinal reinforcement should be at least 0.007 in2 (4.5 mm2) per in (mm) of bar spacing. Spacing of ties should not exceed two-thirds of the smallest dimension of the composite section. Strength of the concrete f c should be between 3 and 8 ksi (20.7 and 55.2 MPa) for normalweight concrete and at least 4 ksi (27.6 MPa) for lightweight concrete. Specified minimum yield stress Fy of steel core and reinforcement should not exceed 60 ksi (414 MPa). Wall thickness of steel pipe or tubing filled with concrete should be at least b√Fy /3E or D√Fy /8E, where b is the width of the face of a rectangular section, D is the outside diameter of a circular section, and E is the elastic modulus of the steel. The AISC LRFD specification gives the design strength of an axially loaded composite column as Pn, where 0.85 and Pn is determined from Pn 0.85As Fcr
w
F a 0 s o b
For c 1.5 2
Fcr 0.658c Fmy
e d t d s A
For c 1.5 Fcr
0.877 Fmy 2c TLFeBOOK
40816_03_p99-130 p. 116
10/22/01
12:42 PM
40816 HICKS Mcghp Chap_03
Page 117
SECOND PASS 7/5/01 pb p. 117
117
COLUMN FORMULAS
l h , e r d 2
s f d l 4 h s h
where c (KL/rm )√Fmy /E m KL effective length of column in (mm) As gross area of steel core in2 (mm2) Fmy Fy c1Fyr(Ar /As) c2 fc(Ac /As) Em E c3Ec(Ac /As) rm radius of gyration of steel core, in 0.3 of the overall thickness of the composite cross section in the plane of buckling for steel shapes Ac cross-sectional area of concrete in2 (mm2) Ar area of longitudinal reinforcement in2 (mm2) Ec elastic modulus of concrete ksi (MPa) Fyr specified minimum yield stress of longitudinal reinforcement, ksi (MPa) For concrete-filled pipe and tubing, c1 1.0, c2 0.85, and c3 0.4. For concrete-encased shapes, c1 0.7, c2 0.6, and c3 0.2. When the steel core consists of two or more steel shapes, they should be tied together with lacing, tie plates, or batten plates to prevent buckling of individual shapes before the concrete attains 0.75 f c. The portion of the required strength of axially loaded encased composite columns resisted by concrete should be developed by direct bearing at connections or shear connectors can be used to transfer into the concrete the load applied directly to the steel column. For direct bearing, the design strength of the concrete is 1.7c fc Ab, where c 0.65 and Ab loaded area, in2 (mm2). Certain restrictions apply. TLFeBOOK
40816_03_p99-130
10/22/01
12:42 PM
40816 HICKS Mcghp Chap_03
118
Page 118
SECOND PASS 7/5/01 pb p. 118
40816
CHAPTER THREE
ELASTIC FLEXURAL BUCKLING OF COLUMNS Elastic buckling is a state of lateral instability that occurs while the material is stressed below the yield point. It is of special importance in structures with slender members. Euler’s formula for pin-ended columns (Fig. 3.7) gives valid results for the critical buckling load, kip (N). This formula is, with L/r as the slenderness ratio of the column,
2EA (L/r)2
P
where E modulus of elasticity of the column material, psi (Mpa) A column cross-sectional area, in2 (mm2) r radius of gyration of the column, in (mm) Figure 3.8 shows some ideal end conditions for slender columns and corresponding critical buckling loads. Elastic critical buckling loads may be obtained for all cases by substituting an effective length KL for the length L of the pinned column, giving P
2EA (KL/r)2
In some cases of columns with open sections, such as a cruciform section, the controlling buckling mode may be one of twisting instead of lateral deformation. If the warping rigidity of the section is negligible, torsional buckling in a pin-ended column occurs at an axial load of P
GJA Ip TLFeBOOK
F l
w
40816_03_p99-130 p. 118
10/22/01
40816 HICKS Mcghp Chap_03
12:42 PM
Page 119
SECOND PASS 7/5/01 pb p. 119
COLUMN FORMULAS
119
s f s s h
,
r c e
a e g
FIGURE 3.7 (a) Buckling of a pin-ended column under axial load. (b) Internal forces hold the column in equilibrium.
where G shear modulus of elasticity J torsional constant A cross-sectional area Ip polar moment of inertia Ix Iy TLFeBOOK
10/22/01
40816 HICKS Mcghp Chap_03
12:42 PM
Page 120
SECOND PASS 7/5/01 pb p. 120
40816
I r
w s
A A FIGURE 3.8 Buckling formulas for columns.
40816_03_p99-130
E d s e E
J
u 120
TLFeBOOK
40816_03_p99-130 p. 120
10/22/01
12:42 PM
40816 HICKS Mcghp Chap_03
Page 121
SECOND PASS 7/5/01 pb p. 121
121
COLUMN FORMULAS
If the section possesses a significant amount of warping rigidity, the axial buckling load is increased to P
A Ip
GJ LEC 2
w
2
where Cw is the warping constant, a function of cross-sectional shape and dimensions.
FIGURE 3.8 Buckling formulas for columns.
ALLOWABLE DESIGN LOADS FOR ALUMINUM COLUMNS Euler’s equation is used for long aluminum columns, and depending on the material, either Johnson’s parabolic or straight-line equation is used for short columns. These equations for aluminum follow: Euler’s equation: Fe
c 2E (L/)2
Johnson’s generalized equation:
√
Fc Fce 1 K
(L/) cE
Fce
n
The value of n, which determines whether the short column formula is the straight-line or parabolic type, is selected TLFeBOOK
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
122
12:42 PM
Page 122
SECOND PASS 7/5/01 pb p. 122
CHAPTER THREE
from Table 3.5. The transition from the long to the short column range is given by
L
cr
√
kcE Fce
where Fe allowable column compressive stress Fce column yield stress and is given as a function of Fcy (compressive yield stress) L length of column radius of gyration of column E modulus of elasticity—noted on nomograms c column-end fixity from Fig. 3.9 n, K, k constants from Table 3.5
FIGURE 3.9 Values of c, column-end fixity, for determining the critical L/ ratio of different loading conditions. TLFeBOOK
40816
t
n
s
e
p. 122
Values Fce psi
MPa
K
k
n
Type Johnson equation
14S–T4 24S–T3 and T4 61S–T6 14S–T6 75S–T6
34,000 40,000 35,000 57,000 69,000
234.4 275.8 241.3 393.0 475.8
39,800 48,000 41,100 61,300 74,200
274.4 330.9 283.4 422.7 511.6
0.385 0.385 0.385 0.250 0.250
3.00 3.00 3.00 2.00 2.00
1.0 1.0 1.0 2.0 2.0
Straight line Straight line Straight line Squared parabolic Squared parabolic
Ref: ANC-5.
TLFeBOOK
Page 123
MPa
12:42 PM
psi
SECOND PASS 7/5/01 pb p. 123
123
Material
10/22/01
Average Fcy
40816_03_p99-130
40816 HICKS Mcghp Chap_03
TABLE 3.5 Material Constants for Common Aluminum Alloys
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
124
12:42 PM
Page 124
SECOND PASS 7/5/01 pb p. 124
40816
CHAPTER THREE
ULTIMATE STRENGTH DESIGN CONCRETE COLUMNS At ultimate strength Pu, kip (N), columns should be capable of sustaining loads as given by the American Concrete Institute required strength equations in Chap. 5, “Concrete Formulas” at actual eccentricities. Pu , may not exceed Pn , where is the capacity reduction factor and Pn , kip (N), is the column ultimate strength. If Po, kip (N), is the column ultimate strength with zero eccentricity of load, then
w
Po 0.85 f c(Ag Ast) fy Ast where fy yield strength of reinforcing steel, ksi (MPa) f c 28-day compressive strength of concrete, ksi (MPa) Ag gross area of column, in2 (mm2) Ast area of steel reinforcement, in2 (mm2) For members with spiral reinforcement then, for axial loads only, Pu 0.85Po For members with tie reinforcement, for axial loads only, Pu 0.80Po Eccentricities are measured from the plastic centroid. This is the centroid of the resistance to load computed for the assumptions that the concrete is stressed uniformly to 0.85 f c and the steel is stressed uniformly to fy. The axial-load capacity Pu kip (N), of short, rectangular members subject to axial load and bending may be determined from TLFeBOOK
e t m t y l c i t
40816_03_p99-130 p. 124
10/22/01
12:42 PM
40816 HICKS Mcghp Chap_03
Page 125
SECOND PASS 7/5/01 pb p. 125
125
COLUMN FORMULAS
Pu (0.85 f cba As fy As fs)
e e e , s n
Pue 0.85 f cba d
a 2
A f (d d ) s y
where e eccentricity, in (mm), of axial load at end of member with respect to centroid of tensile reinforcement, calculated by conventional methods of frame analysis b width of compression face, in (mm)
) ,
a depth of equivalent rectangular compressivestress distribution, in (mm) As area of compressive reinforcement, in2 (mm2) As area of tension reinforcement, in2 (mm2) d distance from extreme compression surface to centroid of tensile reinforcement, in (mm)
s
d distance from extreme compression surface to centroid of compression reinforcement, in (mm) fs tensile stress in steel, ksi (MPa)
. r o r -
The two preceding equations assume that a does not exceed the column depth, that reinforcement is in one or two faces parallel to axis of bending, and that reinforcement in any face is located at about the same distance from the axis of bending. Whether the compression steel actually yields at ultimate strength, as assumed in these and the following equations, can be verified by strain compatibility calculations. That is, when the concrete crushes, the strain in the compression steel, 0.003 (c – d)/c, must be larger than the strain when the steel starts to yield, fy /Es. In this TLFeBOOK
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
126
12:43 PM
Page 126
SECOND PASS 7/5/01 pb p. 126
40816
CHAPTER THREE
case, c is the distance, in (mm), from the extreme compression surface to the neutral axis and Es is the modulus of elasticity of the steel, ksi (MPa). The load Pb for balanced conditions can be computed from the preceding Pu equation with fs fy and
w
a ab 1cb
87,000 1d 87,000 fy
S
The balanced moment, in. kip (k Nm), can be obtained from
P
Mb Pbeb
F P
0.85 fc ba b d d
ab 2
As fy (d d d) As fy d
where eb is the eccentricity, in (mm), of the axial load with respect to the plastic centroid and d is the distance, in (mm), from plastic centroid to centroid of tension reinforcement. When Pu is less than Pb or the eccentricity, e, is greater than eb, tension governs. In that case, for unequal tension and compression reinforcement, the ultimate strength is
Pu 0.85 fcbd m m 1
√
1
e d
e d
C F
P
2 (m m) ed m 1 dd 2
TLFeBOOK
40816_03_p99-130 p. 126
10/22/01
12:43 PM
40816 HICKS Mcghp Chap_03
Page 127
SECOND PASS 7/5/01 pb p. 127
127
COLUMN FORMULAS
f
m fy /0.85f c
where
m m 1
d
As / bd
As / bd
Special Cases of Reinforcement d
For symmetrical reinforcement in two faces, the preceding Pu equation becomes
Pu 0.85 fcbd 1
h , r n
√
1
e d
e d
2 m1 dd ed 2
Column Strength When Compression Governs For no compression reinforcement, the Pu equation becomes
Pu 0.85 f cbd m 1
e d e em √1 d 2 d 2
TLFeBOOK
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
128
12:43 PM
Page 128
SECOND PASS 7/5/01 pb p. 128
40816
CHAPTER THREE
When Pu is greater than Pb, or e is less than eb, compression governs. In that case, the ultimate strength is approximately Pu Po (Po Pb) Pu
Mu Mb
Po 1 (Po /Pb 1)(e/eb)
W
where Mu is the moment capacity under combined axial load and bending, in kip (k Nm) and Po is the axial-load capacity, kip (N), of member when concentrically loaded, as given. For symmetrical reinforcement in single layers, the ultimate strength when compression governs in a column with depth, h, may be computed from Pu
w
T m
e/d Adf 0.5 3he/dbhf 1.18 s y
c
2
S Circular Columns Ultimate strength of short, circular members with bars in a circle may be determined from the following equations:
U a i
When tension controls,
W
Pu 0.85 f c D 2
0.85e mD √ D 0.38 2.5D 2
1
s
0.38 0.85e D
TLFeBOOK
40816_03_p99-130 p. 128
10/22/01
12:43 PM
40816 HICKS Mcghp Chap_03
Page 129
SECOND PASS 7/5/01 pb p. 129
129
COLUMN FORMULAS
n
where D overall diameter of section, in (mm) Ds diameter of circle through reinforcement, in (mm) t Ast /Ag When compression governs,
l d ,
Pu
3e/DA f 1
h
st v s
Ag f c 9.6De /(0.8D 0.67Ds)2 1.18
The eccentricity for the balanced condition is given approximately by eb (0.24 0.39 t m)D
Short Columns a
Ultimate strength of short, square members with depth, h, and with bars in a circle may be computed from the following equations: When tension controls, Pu 0.85bhf c
D e √ h 0.5 0.67 h 2
s
t m
he 0.5
TLFeBOOK
40816_03_p99-130
10/22/01
40816 HICKS Mcghp Chap_03
130
12:43 PM
Page 130
SECOND PASS 7/5/01 pb p. 130
CHAPTER THREE
When compression governs, Pu
3e/DA f 1 st y s
Ag f c 12he/(h 0.67Ds)2 1.18
Slender Columns When the slenderness of a column has to be taken into account, the eccentricity should be determined from e Mc /Pu, where Mc is the magnified moment.
TLFeBOOK
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Chap_04
12:44 PM
Page 131
SECOND PASS
5/5/01 pb p 131
CHAPTER 4
PILES AND PILING FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Ch04
132
12:44 PM
SECOND PASS
Page 132 5/5/01 pb p 132
408
CHAPTER FOUR
ALLOWABLE LOADS ON PILES
L
A dynamic formula extensively used in the United States to determine the allowable static load on a pile is the Engineering News formula. For piles driven by a drop hammer, the allowable load is
V t s d
Pa
2WH p1
For piles driven by a steam hammer, the allowable load is
Pa
d a i c p
2WH p 0.1 w w m
where Pa allowable pile load, tons (kg) W weight of hammer, tons (kg) H height of drop, ft (m) p penetration of pile per blow, in (mm) The preceding two equations include a factor of safety of 6. For a group of piles penetrating a soil stratum of good bearing characteristics and transferring their loads to the soil by point bearing on the ends of the piles, the total allowable load would be the sum of the individual allowable loads for each pile. For piles transferring their loads to the soil by skin friction on the sides of the piles, the total allowable load would be less than the sum on the individual allowable loads for each pile, because of the interaction of the shearing stresses and strains caused in the soil by each pile. TLFeBOOK
w d p
P m t p a z
40816_04_p131-146 32
10/22/01
12:44 PM
40816 HICKS Mcghp Ch04
Page 133
Third Pass 7/19/01 bcj p 133
PILES AND PILING FORMULAS
133
LATERALLY LOADED VERTICAL PILES o ,
s
Vertical-pile resistance to lateral loads is a function of both the flexural stiffness of the shaft, the stiffness of the bearing soil in the upper 4 to 6D length of shaft, where D pile diameter and the degree of pile-head fixity. The lateral-load vs. pile-head deflection relationship is developed from charted nondimensional solutions of Reese and Matlock. The solution assumes the soil modulus K to increase linearly with depth z; that is, K nh z, where nh coefficient of horizontal subgrade reaction. A characteristic pile length T is calculated from T
√
EI nh
where EI pile stiffness. The lateral deflection y of a pile with head free to move and subject to a lateral load Pt and moment Mt applied at the ground line is given by y Ay Pt
. d e l o l l f h
T3 T2 By M t EI EI
where Ay and By are nondimensional coefficients. Nondimensional coefficients are also available for evaluation of pile slope, moment, shear, and soil reaction along the shaft. For positive moment, M Am Pt T Bm M t Positive Mt and Pt values are represented by clockwise moment and loads directed to the right on the pile head at the ground line. The coefficients applicable to evaluation of pile-head deflection and to the maximum positive moment and its approximate position on the shaft, z/T, where z distance below the ground line, are listed in Table 4.1. TLFeBOOK
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Ch04
134
12:44 PM
SECOND PASS
Page 134 5/5/01 pb p 134
408
CHAPTER FOUR
TABLE 4.1 Percentage of Base Load Transmitted to Rock Socket
w
Er /Ep Ls /ds
0.25
1.0
4.0
0.5 1.0 1.5 2.0
54† 31 17† 13†
48 23 12 8
44 18 8† 4
† Estimated by interpretation of finite-element solution; for Poisson’s ratio 0.26.
The negative moment imposed at the pile head by pilecap or another structural restraint can be evaluated as a function of the head slope (rotation) from A PT EI M t t s B B T where s rad represents the counterclockwise () rotation of the pile head and A and B are coefficients (see Table 4.1). The influence of the degrees of fixity of the pile head on y and M can be evaluated by substituting the value of Mt from the preceding equation into the earlier y and M equations. Note that, for the fixed-head case, yf
PtT 3 A B Ay y EI B
TOE CAPACITY LOAD For piles installed in cohesive soils, the ultimate tip load may be computed from TLFeBOOK
A b c c t
S r b A
w c F q i
40816_04_p131-146 34
10/22/01
40816 HICKS Mcghp Ch04
where
12:44 PM
Page 135
Third Pass 7/19/01 bcj p 135
PILES AND PILING FORMULAS
135
Q bu Ab q Ab Nc cu
(4.1)
Ab end-bearing area of pile q bearing capacity of soil Nt bearing-capacity factor cu undrained shear strength of soil within zone 1 pile diameter above and 2 diameters below pile tip
a
n e d f M
Although theoretical conditions suggest that Nc may vary between about 8 and 12, Nc is usually taken as 9. For cohesionless soils, the toe resistance stress, q, is conventionally expressed by Eq. (4.1) in terms of a bearingcapacity factor Nq and the effective overburden pressure at the pile tip vo: q Nqvo ql
Some research indicates that, for piles in sands, q, like fs, reaches a quasi-constant value, ql , after penetrations of the bearing stratum in the range of 10 to 20 pile diameters. Approximately: ql 0.5Nq tan
d
(4.2)
(4.3)
where is the friction angle of the bearing soils below the critical depth. Values of Nq applicable to piles are given in Fig. 4.1. Empirical correlations of soil test data with q and ql have also been applied to predict successfully end-bearing capacity of piles in sand. TLFeBOOK
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Ch04
136
12:44 PM
SECOND PASS
Page 136 5/5/01 pb p 136
408
CHAPTER FOUR
t g p a a i
w a p c D c h FIGURE 4.1 Bearing-capacity factor for granular soils related to angle of internal friction.
p c c
GROUPS OF PILES A pile group may consist of a cluster of piles or several piles in a row. The group behavior is dictated by the group geometry and the direction and location of the load, as well as by subsurface conditions. Ultimate-load considerations are usually expressed in terms of a group efficiency factor, which is used to reduce the capacity of each pile in the group. The efficiency factor Eg is defined as the ratio of the ultimate group capacity TLFeBOOK
w a t d u c r s
40816_04_p131-146 36
10/22/01
40816 HICKS Mcghp Ch04
12:44 PM
Page 137
Third Pass 7/19/01 bcj p 137
PILES AND PILING FORMULAS
137
to the sum of the ultimate capacity of each pile in the group. Eg is conventionally evaluated as the sum of the ultimate peripheral friction resistance and end-bearing capacities of a block of soil with breadth B, width W, and length L, approximately that of the pile group. For a given pile, spacing S and number of piles n, Eg
o
2(BL WL) fs BWg nQ u
where fs is the average peripheral friction stress of block and Qu is the single-pile capacity. The limited number of pile-group tests and model tests available suggest that for cohesive soils Eg 1 if S is more than 2.5 pile diameters D and for cohesionless soils Eg 1 for the smallest practical spacing. A possible exception might be for very short, heavily tapered piles driven in very loose sands. In practice, the minimum pile spacing for conventional piles is in the range of 2.5 to 3.0D. A larger spacing is typically applied for expanded-base piles. A very approximate method of pile-group analysis calculates the upper limit of group drag load, Qgd from Q gd AFFHF PHcu
s y n e r y
(4.4)
(4.5)
where Hf , f , and AF represent the thickness, unit weight, and area of fill contained within the group. P, H, and cu are the circumference of the group, the thickness of the consolidating soil layers penetrated by the piles, and their undrained shear strength, respectively. Such forces as Qgd could only be approached for the case of piles driven to rock through heavily surcharged, highly compressible subsoils. TLFeBOOK
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Ch04
138
12:44 PM
SECOND PASS
Page 138 5/5/01 pb p 138
408
CHAPTER FOUR
Design of rock sockets is conventionally based on Q d d s L s fR
2 d q 4 s a
T s (4.6)
where Qd allowable design load on rock socket ds socket diameter Ls socket length fR allowable concrete-rock bond stress qa allowable bearing pressure on rock Load-distribution measurements show, however, that much less of the load goes to the base than is indicated by Eq. (4.6). This behavior is demonstrated by the data in Table 4.1, where Ls /ds is the ratio of the shaft length to shaft diameter and Er /Ep is the ratio of rock modulus to shaft modulus. The finite-element solution summarized in Table 4.1 probably reflects a realistic trend if the average socketwall shearing resistance does not exceed the ultimate fR value; that is, slip along the socket side-wall does not occur. A simplified design approach, taking into account approximately the compatibility of the socket and base resistance, is applied as follows: 1. Proportion the rock socket for design load Qd with Eq. (4.6) on the assumption that the end-bearing stress is less than qa [say qa /4, which is equivalent to assuming that the base load Q b ( /4) d 2s qa /4]. 2. Calculate Qb RQd, where R is the base-load ratio interpreted from Table 4.1. 3. If RQd does not equal the assumed Qb , repeat the procedure with a new qa value until an approximate convergence is achieved and q qa. TLFeBOOK
J i d f 1 t b T d
F T d f a b v
w
40816_04_p131-146 38
10/22/01
40816 HICKS Mcghp Ch04
12:44 PM
Page 139
Third Pass 7/19/01 bcj p 139
PILES AND PILING FORMULAS
)
h . e t t e R
. ,
The final design should be checked against the established settlement tolerance of the drilled shaft. Following the recommendations of Rosenberg and Journeaux, a more realistic solution by the previous method is obtained if fRu is substituted for fR. Ideally, fRu should be determined from load tests. If this parameter is selected from data that are not site specific, a safety factor of at least 1.5 should be applied to fRu in recognition of the uncertainties associated with the UC strength correlations (Rosenberg, P. and Journeaux, N. L., “Friction and End-Bearing Tests on Bedrock for High-Capacity Socket Design,” Canadian Geotechnical Journal, 13(3)).
FOUNDATION-STABILITY ANALYSIS The maximum load that can be sustained by shallow foundation elements at incipient failure (bearing capacity) is a function of the cohesion and friction angle of bearing soils as well as the width B and shape of the foundation. The net bearing capacity per unit area, qu, of a long footing is conventionally expressed as qu f cu Nc voNq f BN
. s g o -
139
where
(4.7)
f 1.0 for strip footings and 1.3 for circular and square footings cu undrained shear strength of soil vo effective vertical shear stress in soil at level of bottom of footing f 0.5 for strip footings, 0.4 for square footings, and 0.6 for circular footings TLFeBOOK
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Ch04
140
12:44 PM
SECOND PASS
Page 140 5/5/01 pb p 140
408
CHAPTER FOUR
unit weight of soil B width of footing for square and rectangular footings and radius of footing for circular footings Nc, Nq, N bearing-capacity factors, functions of angle of internal friction For undrained (rapid) loading of cohesive soils, 0 and Eq. (4.7) reduces to qu N c cu
T S
R C
†
(4.8)
t ‡
where Nc f Nc. For drained (slow) loading of cohesive soils, and cu are defined in terms of effective friction angle and effective stress cu. Modifications of Eq. (4.7) are also available to predict the bearing capacity of layered soil and for eccentric loading. Rarely, however, does qu control foundation design when the safety factor is within the range of 2.5 to 3. (Should creep or local yield be induced, excessive settlements may occur. This consideration is particularly important when selecting a safety factor for foundations on soft to firm clays with medium to high plasticity.) Equation (4.7) is based on an infinitely long strip footing and should be corrected for other shapes. Correction factors by which the bearing-capacity factors should be multiplied are given in Table 4.2, in which L footing length. The derivation of Eq. (4.7) presumes the soils to be homogeneous throughout the stressed zone, which is seldom the case. Consequently, adjustments may be required for departures from homogeneity. In sands, if there is a moderate variation in strength, it is safe to use Eq. (4.7), but with bearingcapacity factors representing a weighted average strength. TLFeBOOK
s c m f a r a f t
w
F 0
40816_04_p131-146 40
10/22/01
40816 HICKS Mcghp Ch04
12:44 PM
Page 141
Third Pass 7/19/01 bcj p 141
141
PILES AND PILING FORMULAS
TABLE 4.2 Shape Corrections for Bearing-Capacity Factors of Shallow Foundations†
r r
Rectangle‡
0
Correction factor
Shape of foundation
Circle and square
Nc
Nq
N 1 N
1
B L
Nq Nc
q c
1
tan B L
1 tan
Ny 1 0.4
BL
0.60
After De Beer, E. E., as modified by Vesic, A. S. See Fang, H. Y., Foundation Engineering Handbook, 2d ed., Van Nostrand Reinhold, New York. No correction factor is needed for long-strip foundations.
†
)
‡
e n e n d y n m n e g e -
Eccentric loading can have a significant impact on selection of the bearing value for foundation design. The conventional approach is to proportion the foundation to maintain the resultant force within its middle third. The footing is assumed to be rigid and the bearing pressure is assumed to vary linearly as shown by Fig. (4.2b.) If the resultant lies outside the middle third of the footing, it is assumed that there is bearing over only a portion of the footing, as shown in Fig. (4.2d.) For the conventional case, the maximum and minimum bearing pressures are qm
P BL
1 6eB
(4.9)
where B width of rectangular footing L length of rectangular footing e eccentricity of loading For the other case (Fig. 4.3c), the soil pressure ranges from 0 to a maximum of TLFeBOOK
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Ch04
142
12:44 PM
SECOND PASS
Page 142 5/5/01 pb p 142
408
CHAPTER FOUR
qm
2P 3L(B/2 e)
(4.10)
For square or rectangular footings subject to overturning about two principal axes and for unsymmetrical footings, the loading eccentricities e1 and e2 are determined about the two principal axes. For the case where the full bearing area of the footings is engaged, qm is given in terms of the distances from the principal axes, c1 and c2, the radius of gyration of the footing area about the principal axes r1 and r2, and the area of the footing A as qm
P A
1 erc
1 1 2 1
e2c2 r 22
(4.11)
F t e m o (
A P t e
w p e a E t e t a o 1 e
FIGURE 4.2 Footings subjected to overturning.
TLFeBOOK
40816_04_p131-146 42
10/22/01
40816 HICKS Mcghp Ch04
12:44 PM
Page 143
Third Pass 7/19/01 bcj p 143
143
PILES AND PILING FORMULAS
) g s, e a 2,
)
For the case where only a portion of the footing is bearing, the maximum pressure may be approximated by trial and error. For all cases of sustained eccentric loading, the maximum (edge) pressures should not exceed the shear strength of the soil and also the factor of safety should be at least 1.5 (preferably 2.0) against overturning.
AXIAL-LOAD CAPACITY OF SINGLE PILES Pile capacity Qu may be taken as the sum of the shaft and toe resistances, Qsu and Qbu, respectively. The allowable load Qa may then be determined from either Eq. (4.12) or (4.13): Q su Q bu F Q su Q Qa bu F1 F2 Qa
(4.12) (4.13)
where F, F1, and F2 are safety factors. Typically, F for permanent structures is between 2 and 3, but may be larger, depending on the perceived reliability of the analysis and construction as well as the consequences of failure. Equation (4.13) recognizes that the deformations required to fully mobilize Qsu and Qbu are not compatible. For example, Qsu may be developed at displacements less than 0.25 in (6.35 mm), whereas Qbu may be realized at a toe displacement equivalent to 5 percent to 10 percent of the pile diameter. Consequently, F1 may be taken as 1.5 and F2 as 3.0, if the equivalent single safety factor equals F or larger. (If Q su/Q bu1.0, F is less than the TLFeBOOK
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Ch04
144
12:44 PM
SECOND PASS
Page 144 5/5/01 pb p 144
408
CHAPTER FOUR
2.0 usually considered as a major safety factor for permanent structures.)
s t c
SHAFT SETTLEMENT Drilled-shaft settlements can be estimated by empirical correlations or by load-deformation compatibility analyses. Other methods used to estimate settlement of drilled shafts, singly or in groups, are identical to those used for piles. These include elastic, semiempirical elastic, and load-transfer solutions for single shafts drilled in cohesive or cohesionless soils. Resistance to tensile and lateral loads by straight-shaft drilled shafts should be evaluated as described for pile foundations. For relatively rigid shafts with characteristic length T greater than 3, there is evidence that bells increase the lateral resistance. The added ultimate resistance to uplift of a belled shaft Qut can be approximately evaluated for cohesive soils models for bearing capacity [Eq. (4.14)] and friction cylinder [Eq. (4.15)] as a function of the shaft diameter D and bell diameter Db (Meyerhof, G. G. and Adams, J. I., “The Ultimate Uplift Capacity of Foundations,” Canadian Geotechnical Journal, 5(4):1968.) For the bearing-capacity solution,
w s c w w
S C T f p
(4.14)
e a s v
The shear-strength reduction factor in Eq. (4.14) considers disturbance effects and ranges from 12 (slurry construction) to 34 (dry construction). The cu represents the undrained shear strength of the soil just above the bell surface, and Nc is a bearing-capacity factor.
t w l r p
Q ul
(D 2b D 2)Nc cu Wp 4
TLFeBOOK
40816_04_p131-146 44
10/22/01
40816 HICKS Mcghp Ch04
12:44 PM
Page 145
Third Pass 7/19/01 bcj p 145
PILES AND PILING FORMULAS
-
The failure surface of the friction cylinder model is conservatively assumed to be vertical, starting from the base of the bell. Qut can then be determined for both cohesive and cohesionless soils from Q ul b L fut Ws Wp
r y e s t e c e t r d t d -
) e -
145
(4.15)
where fut is the average ultimate skin-friction stress in tension developed on the failure plane; that is, fut 0.8cu for clays or K vo tan for sands. Ws and Wp represent the weight of soil contained within the failure plane and the shaft weight, respectively.
SHAFT RESISTANCE IN COHESIONLESS SOILS The shaft resistance stress fs is a function of the soil-shaft friction angle , degree, and an empirical lateral earthpressure coefficient K: fs K vo tan fl
(4.16)
At displacement-pile penetrations of 10 to 20 pile diameters (loose to dense sand), the average skin friction reaches a limiting value fl. Primarily depending on the relative density and texture of the soil, fl has been approximated conservatively by using Eq. (4.16) to calculate fs. For relatively long piles in sand, K is typically taken in the range of 0.7 to 1.0 and is taken to be about 5, where is the angle of internal friction, degree. For piles less than 50 ft (15.2 m) long, K is more likely to be in the range of 1.0 to 2.0, but can be greater than 3.0 for tapered piles. TLFeBOOK
40816_04_p131-146
10/22/01
40816 HICKS Mcghp Ch04
146
12:44 PM
SECOND PASS
Page 146 5/5/01 pb p 146
CHAPTER FOUR
Empirical procedures have also been used to evaluate fs from in situ tests, such as cone penetration, standard penetration, and relative density tests. Equation (4.17), based on standard penetration tests, as proposed by Meyerhof, is generally conservative and has the advantage of simplicity: fs
N 50
(4.17)
where N average standard penetration resistance within the embedded length of pile and fs is given in tons/ft2. (Meyerhof, G. G., “Bearing Capacity and Settlement of Pile Foundations,” ASCE Journal of Geotechnical Engineering Division, 102(GT3):1976.)
TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 147
40816 HICKS Mcghp Chap_05 Pgs 147 7/10/2001
CHAPTER 5
CONCRETE FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_05a_p147-195
10/22/01
12:45 PM
Page 148
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 148
148
CHAPTER FIVE
REINFORCED CONCRETE When working with reinforced concrete and when designing reinforced concrete structures, the American Concrete Institute (ACI) Building Code Requirements for Reinforced Concrete, latest edition, is widely used. Future references to this document are denoted as the ACI Code. Likewise, publications of the Portland Cement Association (PCA) find extensive use in design and construction of reinforced concrete structures. Formulas in this chapter cover the general principles of reinforced concrete and its use in various structural applications. Where code requirements have to be met, the reader must refer to the current edition of the ACI Code previously mentioned. Likewise, the PCA publications should also be referred to for the latest requirements and recommendations.
WATER/CEMENTITIOUS MATERIALS RATIO
a 0 r 2 c v w w a v l ( d t i t e c
The water/cementitious (w/c) ratio is used in both tensile and compressive strength analyses of Portland concrete cement. This ratio is found from
J
w w m c wc
A m m v a
where wm weight of mixing water in batch, lb (kg); and wc weight of cementitious materials in batch, lb (kg). The ACI Code lists the typical relationship between the w/c ratio by weight and the compressive strength of concrete. Ratios for non-air-entrained concrete vary between 0.41 for TLFeBOOK
40816_05a_p147-195 148
10/22/01
12:45 PM
40816 HICKS Mcghp Chap_05 Pgs 149 7/10/2001
CONCRETE FORMULAS
e d o d f r y e .
e e
d e . r
Page 149
149
a 28-day compressive strength of 6000 lb/in2 (41 MPa) and 0.82 for 2000 lb/in2 (14 MPa). Air-entrained concrete w/c ratios vary from 0.40 to 0.74 for 5000 lb/in2 (34 MPa) and 2000 lb/in2 (14 MPa) compressive strength, respectively. Be certain to refer to the ACI Code for the appropriate w/c value when preparing designs or concrete analyses. Further, the ACI Code also lists maximum w/c ratios when strength data are not available. Absolute w/c ratios by weight vary from 0.67 to 0.38 for non-air-entrained concrete and from 0.54 to 0.35 for air-entrained concrete. These values are for a specified 28-day compressive strength fc in lb/in2 or MPa, of 2500 lb/in2 (17 MPa) to 5000 lb/in2 (34 MPa). Again, refer to the ACI Code before making any design or construction decisions. Maximum w/c ratios for a variety of construction conditions are also listed in the ACI Code. Construction conditions include concrete protected from exposure to freezing and thawing; concrete intended to be watertight; and concrete exposed to deicing salts, brackish water, seawater, etc. Application formulas for w/c ratios are given later in this chapter.
JOB MIX CONCRETE VOLUME A trial batch of concrete can be tested to determine how much concrete is to be delivered by the job mix. To determine the volume obtained for the job, add the absolute volume Va of the four components—cements, gravel, sand, and water. Find the Va for each component from Va
WL (SG)Wu TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 150
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 150
150
where
CHAPTER FIVE
Va absolute volume, ft3 (m3)
T
WL weight of material, lb (kg) SG specific gravity of the material wu density of water at atmospheric conditions (62.4 lb/ft3; 1000 kg/m3)
T d s
Then, job yield equals the sum of Va for cement, gravel, sand, and water.
R MODULUS OF ELASTICITY OF CONCRETE The modulus of elasticity of concrete Ec—adopted in modified form by the ACI Code—is given by Ec 33w1.5 c √f c
1 2 3 4 5
lb/in2 in USCS units
0.043w1.5 c √fc
A fi t
MPa in SI units
With normal-weight, normal-density concrete these two relations can be simplified to Ec 57,000 √fc 4700 √fc
C A
lb/in2 in USCS units MPa in SI units
where Ec modulus of elasticity of concrete, lb/in2 (MPa); and fc specified 28-day compressive strength of concrete, lb/in2 (MPa). TLFeBOOK
T s w a A
40816_05a_p147-195 150
10/22/01
12:45 PM
Page 151
40816 HICKS Mcghp Chap_05 Pgs 151 7/10/2001
CONCRETE FORMULAS
151
TENSILE STRENGTH OF CONCRETE The tensile strength of concrete is used in combined-stress design. In normal-weight, normal-density concrete the tensile strength can be found from s ,
fr 7.5 √fc
lb/in2 in USCS units
fr 0.7 √fc
MPa in SI units
REINFORCING STEEL
-
American Society for Testing and Materials (ASTM) specifications cover renforcing steel. The most important properties of reinforcing steel are 1. 2. 3. 4. 5.
Modulus of elasticity Es, lb/in2 (MPa) Tensile strength, lb/in2 (MPa) Yield point stress fy, lb/in2 (MPa) Steel grade designation (yield strength) Size or diameter of the bar or wire
o
CONTINUOUS BEAMS AND ONE-WAY SLABS
; -
The ACI Code gives approximate formulas for finding shear and bending moments in continuous beams and oneway slabs. A summary list of these formulas follows. They are equally applicable to USCS and SI units. Refer to the ACI Code for specific applications of these formulas. TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 152
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 152
152
CHAPTER FIVE
For Positive Moment
E
End spans If discontinuous end is unrestrained If discontinuous end is integral with the support Interior spans
wl 2n 11
R a
wl 2n 14 wl 2n 16
D C For Negative Moment Negative moment at exterior face of first interior support Two spans More than two spans Negative moment at other faces of interior supports Negative moment at face of all supports for (a) slabs with spans not exceeding 10 ft (3 m) and (b) beams and girders where the ratio of sum of column stiffness to beam stiffness exceeds 8 at each end of the span Negative moment at interior faces of exterior supports, for members built integrally with their supports Where the support is a spandrel beam or girder Where the support is a column
wl 2n 9 wl 2n 10 wl 2n 11
B wl 2n 12
wl 2n 24 wl 2n 16
Shear Forces Shear in end members at first interior support Shear at all other supports
A r a s s C
1.15 wl n 2 wl n 2 TLFeBOOK
C t ( w R t e e c
40816_05a_p147-195 152
10/22/01
12:45 PM
Page 153
40816 HICKS Mcghp Chap_05 Pgs 153 7/10/2001
CONCRETE FORMULAS
153
End Reactions
1
Reactions to a supporting beam, column, or wall are obtained as the sum of shear forces acting on both sides of the support.
4 6
DESIGN METHODS FOR BEAMS, COLUMNS, AND OTHER MEMBERS
9 0 1
A number of different design methods have been used for reinforced concrete construction. The three most common are working-stress design, ultimate-strength design, and strength design method. Each method has its backers and supporters. For actual designs the latest edition of the ACI Code should be consulted.
Beams 2
4 6
2 2
Concrete beams may be considered to be of three principal types: (1) rectangular beams with tensile reinforcing only, (2) T beams with tensile reinforcing only, and (3) beams with tensile and compressive reinforcing. Rectangular Beams with Tensile Reinforcing Only. This type of beam includes slabs, for which the beam width b equals 12 in (305 mm) when the moment and shear are expressed per foot (m) of width. The stresses in the concrete and steel are, using working-stress design formulas, fc
2M kjbd 2
fs
M M As jd pjbd 2 TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 154
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 154
154
CHAPTER FIVE
where b width of beam [equals 12 in (304.8 mm) for slab], in (mm) d effective depth of beam, measured from compressive face of beam to centroid of tensile reinforcing (Fig. 5.1), in (mm) M bending moment, lb . in (k . Nm) fc compressive stress in extreme fiber of concrete, lb/in2 (MPa) fs stress in reinforcement, lb/in2 (MPa) As cross-sectional area of tensile reinforcing, in2 (mm2) j ratio of distance between centroid of compression and centroid of tension to depth d k ratio of depth of compression area to depth d p ratio of cross-sectional area of tensile reinforcing to area of the beam ( As /bd) For approximate design purposes, j may be assumed to be 8 and k, 13. For average structures, the guides in Table 5.1 to the depth d of a reinforced concrete beam may be used. For a balanced design, one in which both the concrete and the steel are stressed to the maximum allowable stress, the following formulas may be used:
7
bd 2
M K
K
1 f kj pfs j 2 e
Values of K, k, j, and p for commonly used stresses are given in Table 5.2. TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 155
40816 HICKS Mcghp Chap_05 Pgs 155 7/10/2001
TLFeBOOK
154
r e
,
, d g e o e ,
e 155
FIGURE 5.1 Rectangular concrete beam with tensile reinforcing only.
40816_05a_p147-195
10/22/01
12:45 PM
Page 156
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 156
156
CHAPTER FIVE
TABLE 5.1 Guides to Depth d of Reinforced Concrete Beam† Member
d
Roof and floor slabs Light beams Heavy beams and girders
l/25 l/15 l/12–l/10
B w s a m s b
l is the span of the beam or slab in inches (millimeters). The width of a beam should be at least l/32. †
T Beams with Tensile Reinforcing Only. When a concrete slab is constructed monolithically with the supporting concrete beams, a portion of the slab acts as the upper flange of the beam. The effective flange width should not exceed (1) one-fourth the span of the beam, (2) the width of the web portion of the beam plus 16 times the thickness of the slab, or (3) the center-to-center distance between beams. T beams where the upper flange is not a portion of a slab should have a flange thickness not less than one-half the width of the web and a flange width not more than four times the width of the web. For preliminary designs, the preceding formulas given for rectangular beams with tensile reinforcing only can be used, because the neutral axis is usually in, or near, the flange. The area of tensile reinforcing is usually critical. TABLE 5.2 Coefficients K, k, j, p for Rectangular Sections† fs
n
fs
K
k
j
p
2000 2500 3000 3750
15 12 10 8
900 1125 1350 1700
175 218 262 331
0.458 0.458 0.458 0.460
0.847 0.847 0.847 0.847
0.0129 0.0161 0.0193 0.0244
†
fs 16,000 lb/in2 (110 MPa).
TLFeBOOK
w
C p e a p I s i s
40816_05a_p147-195 156
10/22/01
12:45 PM
Page 157
40816 HICKS Mcghp Chap_05 Pgs 157 7/10/2001
CONCRETE FORMULAS
157
Beams with Tensile and Compressive Reinforcing. Beams with compressive reinforcing are generally used when the size of the beam is limited. The allowable beam dimensions are used in the formulas given earlier to determine the moment that could be carried by a beam without compressive reinforcement. The reinforcing requirements may then be approximately determined from As e f ) b , s e b e n e e
9 1 3 4
8M 7fs d
Asc
M M nfc d
where As total cross-sectional area of tensile reinforcing, in2 (mm2) Asc cross-sectional area of compressive reinforcing, in2 (mm2) M total bending moment, lbin (KNm) M bending moment that would be carried by beam of balanced design and same dimensions with tensile reinforcing only, lbin (KNm) n ratio of modulus of elasticity of steel to that of concrete Checking Stresses in Beams. Beams designed using the preceding approximate formulas should be checked to ensure that the actual stresses do not exceed the allowable, and that the reinforcing is not excessive. This can be accomplished by determining the moment of inertia of the beam. In this determination, the concrete below the neutral axis should not be considered as stressed, whereas the reinforcing steel should be transformed into an equivalent concrete section. For tensile reinforcing, this transformation is made TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 158
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 158
158
CHAPTER FIVE
by multiplying the area As by n, the ratio of the modulus of elasticity of steel to that of concrete. For compressive reinforcing, the area Asc is multiplied by 2(n – 1). This factor includes allowances for the concrete in compression replaced by the compressive reinforcing and for the plastic flow of concrete. The neutral axis is then located by solving
a
w
2 bc 2c 2(n 1)Asccsc nAscs
1
for the unknowns cc, csc, and cs (Fig. 5.2). The moment of inertia of the transformed beam section is I 13bc 3c 2(n 1)Ascc 2sc nAs c 2s
a S s c
w
FIGURE 5.2 Transformed section of concrete beam.
TLFeBOOK
40816_05a_p147-195 158
10/22/01
12:45 PM
Page 159
40816 HICKS Mcghp Chap_05 Pgs 159 7/10/2001
159
CONCRETE FORMULAS
f r d f
f
and the stresses are fc
Mcc I
fsc
2nMcsc I
fs
nMcs I
where fc, fsc, fs actual unit stresses in extreme fiber of concrete, in compressive reinforcing steel, and in tensile reinforcing steel, respectively, lb/in2 (MPa) cc, csc, cs distances from neutral axis to face of concrete, to compressive reinforcing steel, and to tensile reinforcing steel, respectively, in (mm) I moment of inertia of transformed beam section, in4 (mm4) b beam width, in (mm) and As, Asc, M, and n are as defined earlier in this chapter. Shear and Diagonal Tension in Beams. The shearing unit stress, as a measure of diagonal tension, in a reinforced concrete beam is v
V bd
where v shearing unit stress, lb/in2 (MPa) V total shear, lb (N) b width of beam (for T beam use width of stem), in (mm) d effective depth of beam TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 160
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 160
160
CHAPTER FIVE
If the value of the shearing stress as computed earlier exceeds the allowable shearing unit stress as specified by the ACI Code, web reinforcement should be provided. Such reinforcement usually consists of stirrups. The crosssectional area required for a stirrup placed perpendicular to the longitudinal reinforcement is Av
(V V)s fi d
where Av cross-sectional area of web reinforcement in distance s (measured parallel to longitudinal reinforcement), in2 (mm2) fv allowable unit stress in web reinforcement, lb/in2 (MPa) V total shear, lb (N) V shear that concrete alone could carry ( vc bd), lb (N) s spacing of stirrups in direction parallel to that of longitudinal reinforcing, in (mm) d effective depth, in (mm) Stirrups should be so spaced that every 45° line extending from the middepth of the beam to the longitudinal tension bars is crossed by at least one stirrup. If the total shearing unit stress is in excess of 3 √f c lb/in2 (MPa), every such line should be crossed by at least two stirrups. The shear stress at any section should not exceed 5 √f c lb/in2 (MPa). Bond and Anchorage for Reinforcing Bars. In beams in which the tensile reinforcing is parallel to the compression face, the bond stress on the bars is TLFeBOOK
2.1√fc
3√fc
6.5√fc or 400, whichever is less
6.5√fc or 400, whichever is less
Plain bars
1.7√fc or 160, whichever is less
2.4√fc or 160, whichever is less
† ‡
lb/in ( 0.006895 MPa). fc compressive strength of concrete, lb/in2 (MPa); D nominal diameter of bar, in (mm). 2
TLFeBOOK
Page 161
4.8√fc or 500, whichever is less D
12:45 PM
3.4√fc or 350, whichever is less D
10/22/01
161
Tension bars with sizes and deformations conforming to ASTM A305 Tension bars with sizes and deformations conforming to ASTM A408 Deformed compression bars
40816_05a_p147-195
Other bars‡
40816 HICKS Mcghp Chap_05 Pgs 161 7/10/2001
Horizontal bars with more than 12 in (30.5 mm) of concrete cast below the bar‡
160
r y . o
n l
,
,
t
l l y r .
n n
TABLE 5.3 Allowable Bond Stresses†
40816_05a_p147-195
10/22/01
12:45 PM
Page 162
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 162
162
CHAPTER FIVE
u
V jd 0
where u bond stress on surface of bar, lb/in2 (MPa) V total shear, lb (N) d effective depth of beam, in (mm)
0 sum of perimeters of tensile reinforcing bars, in (mm)
T T m a
For preliminary design, the ratio j may be assumed to be 7/8. Bond stresses may not exceed the values shown in Table 5.3. w Columns The principal columns in a structure should have a minimum diameter of 10 in (255 mm) or, for rectangular columns, a minimum thickness of 8 in (203 mm) and a minimum gross cross-sectional area of 96 in2 (61,935 mm2). Short columns with closely spaced spiral reinforcing enclosing a circular concrete core reinforced with vertical bars have a maximum allowable load of P Ag(0.25fc fs pg) where P total allowable axial load, lb (N) Ag gross cross-sectional area of column, in2 (mm2) f c compressive strength of concrete, lb/in2 (MPa) TLFeBOOK
T e b e ( g S o r
40816_05a_p147-195 162
10/22/01
12:45 PM
Page 163
40816 HICKS Mcghp Chap_05 Pgs 163 7/10/2001
CONCRETE FORMULAS
163
fs allowable stress in vertical concrete reinforcing, lb/in2 (MPa), equal to 40 percent of the minimum yield strength, but not to exceed 30,000 lb/in2 (207 MPa) pg ratio of cross-sectional area of vertical reinforcing steel to gross area of column Ag ,
e n
The ratio pg should not be less than 0.01 or more than 0.08. The minimum number of bars to be used is six, and the minimum size is No. 5. The spiral reinforcing to be used in a spirally reinforced column is ps 0.45
Ag f c 1 Ac fy
where ps ratio of spiral volume to concrete-core volume (out-to-out spiral) , s g l
) )
Ac cross-sectional area of column core (out-toout spiral), in2 (mm2) fy yield strength of spiral reinforcement, lb/in2 (MPa), but not to exceed 60,000 lb/in2 (413 MPa) The center-to-center spacing of the spirals should not exceed one-sixth of the core diameter. The clear spacing between spirals should not exceed one-sixth the core diameter, or 3 in (76 mm), and should not be less than 1.375 in (35 mm), or 1.5 times the maximum size of coarse aggregate used. Short Columns with Ties. The maximum allowable load on short columns reinforced with longitudinal bars and separate lateral ties is 85 percent of that given earlier for spirally TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 164
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 164
164
CHAPTER FIVE
reinforced columns. The ratio pg for a tied column should not be less than 0.01 or more than 0.08. Longitudinal reinforcing should consist of at least four bars; minimum size is No. 5.
l a
Long Columns. Allowable column loads where compression governs design must be adjusted for column length as follows:
C a a t t
1. If the ends of the column are fixed so that a point of contraflexure occurs between the ends, the applied axial load and moments should be divided by R from (R cannot exceed 1.0) R 1.32
0.006h r
2. If the relative lateral displacement of the ends of the columns is prevented and the member is bent in a single curvature, applied axial loads and moments should be divided by R from (R cannot exceed 1.0) R 1.07
0.008h r
where h unsupported length of column, in (mm) r radius of gyration of gross concrete area, in (mm) 0.30 times depth for rectangular column 0.25 times diameter for circular column R long-column load reduction factor Applied axial load and moment when tension governs design should be similarly adjusted, except that R varies TLFeBOOK
w
40816_05a_p147-195 164
10/22/01
12:45 PM
Page 165
40816 HICKS Mcghp Chap_05 Pgs 165 7/10/2001
165
CONCRETE FORMULAS
t g . s f l -
linearly with the axial load from the values given at the balanced condition. Combined Bending and Compression. The strength of a symmetrical column is controlled by compression if the equivalent axial load N has an eccentricity e in each principal direction no greater than given by the two following equations and by tension if e exceeds these values in either principal direction. For spiral columns, eb 0.43 pg mDs 0.14t For tied columns, eb (0.67pg m 0.17)d
e e e
where e eccentricity, in (mm) eb maximum permissible eccentricity, in (mm) N eccentric load normal to cross section of column pg ratio of area of vertical reinforcement to gross concrete area m fy /0.85 fc
)
Ds diameter of circle through centers of longitudinal reinforcement, in (mm) t diameter of column or overall depth of column, in (mm)
s s
d distance from extreme compression fiber to centroid of tension reinforcement, in (mm) fy yield point of reinforcement, lb/in2 (MPa) TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 166
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 166
166
CHAPTER FIVE
Design of columns controlled by compression is based on the following equation, except that the allowable load N may not exceed the allowable load P, given earlier, permitted when the column supports axial load only: fa fbx fby 1.0 Fa Fb Fb where fa axial load divided by gross concrete area, lb/in2 (MPa) fbx, fby bending moment about x and y axes, divided by section modulus of corresponding transformed uncracked section, lb/in2 (MPa)
c m f
W
Fb allowable bending stress permitted for bending alone, lb/in2 (MPa) Fa 0.34(1 pgm) fc The allowable bending load on columns controlled by tension varies linearly with the axial load from M0 when the section is in pure bending to Mb when the axial load is Nb.
w y a
P
For spiral columns, M0 0.12Ast fyDs For tied columns, M0 0.40As fy(d d) where Ast total area of longitudinal reinforcement, in2 (mm2) fy yield strength of reinforcement, lb/in2 (MPa) Ds diameter of circle through centers of longitudinal reinforcement, in (mm) TLFeBOOK
S c a c s a e b
40816_05a_p147-195 166
10/22/01
12:45 PM
Page 167
40816 HICKS Mcghp Chap_05 Pgs 167 7/10/2001
167
CONCRETE FORMULAS
d N -
,
As area of tension reinforcement, in2 (mm2) d distance from extreme compression fiber to centroid of tension reinforcement, in (mm) Nb and Mb are the axial load and moment at the balanced condition (i.e., when the eccentricity e equals eb as determined). At this condition, Nb and Mb should be determined from Mb Nbeb
y d -
y e .
When bending is about two axes, Mx My 1 M0x M0y where Mz and My are bending moments about the x and y axes, and M0x and M0y are the values of M0 for bending about these axes.
PROPERTIES IN THE HARDENED STATE
) ) -
Strength is a property of concrete that nearly always is of concern. Usually, it is determined by the ultimate strength of a specimen in compression, but sometimes flexural or tensile capacity is the criterion. Because concrete usually gains strength over a long period of time, the compressive strength at 28 days is commonly used as a measure of this property. The 28-day compressive strength of concrete can be estimated from the 7-day strength by a formula proposed by W. A. Slater: S28 S7 30√S7 TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 168
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 168
168
CHAPTER FIVE
where S28 28-day compressive strength, lb/in2 (MPa), and S7 7-day strength, lb/in2 (MPa). Concrete may increase significantly in strength after 28 days, particularly when cement is mixed with fly ash. Therefore, specification of strengths at 56 or 90 days is appropriate in design. Concrete strength is influenced chiefly by the water/cement ratio; the higher this ratio is, the lower the strength. The relationship is approximately linear when expressed in terms of the variable C/W, the ratio of cement to water by weight. For a workable mix, without the use of water reducing admixtures,
T F l a
w
C S28 2700 760 W Tensile strength of concrete is much lower than compressive strength and, regardless of the types of test, usually has poor correlation with fc. As determined in flexural tests, the tensile strength (modulus of rupture—not the true strength) is about 7√fc for the higher strength concretes and 10√fc for the lower strength concretes. Modulus of elasticity Ec , generally used in design for concrete, is a secant modulus. In ACI 318, “Building Code Requirements for Reinforced Concrete,” it is determined by
H i
Ec w1.533 √fc where w weight of concrete, lb/ft3 (kg/m3); and fc specified compressive strength at 28 days, lb/in2 (MPa). For normal-weight concrete, with w 145 lb/ft3 (kg/m3),
a
Ec 57,000 √fc w (
The modulus increases with age, as does the strength. TLFeBOOK
40816_05a_p147-195 168
10/22/01
12:45 PM
Page 169
40816 HICKS Mcghp Chap_05 Pgs 169 7/10/2001
CONCRETE FORMULAS
169
d
TENSION DEVELOPMENT LENGTHS
, . t f r ,
For bars and deformed wire in tension, basic development length is defined by the equations that follow. For No. 11 and smaller bars, ld
0.04Ab fy √fc
where Ab area of bar, in2 (mm2) fy yield strength of bar steel, lb/in2 (MPa)
y , ) r e y
r
fc 28-day compressive strength of concrete, lb/in2 (MPa) However, ld should not be less than 12 in (304.8 mm), except in computation of lap splices or web anchorage. For No. 14 bars, ld 0.085
fy √fc
ld 0.125
fy √fc
For No. 18 bars,
and for deformed wire, ld 0.03db
fy 20,000 A fy 0.02 w √fc Sw √fc
where Aw is the area, in2 (mm2); and sw is the spacing, in (mm), of the wire to be developed. Except in computation of TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 170
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 170
170
CHAPTER FIVE
lap splices or development of web reinforcement, ld should not be less than 12 in (304.8 mm).
COMPRESSION DEVELOPMENT LENGTHS For bars in compression, the basic development length ld is defined as ld
T e e 0 e f m m y
0.02 fy db 0.0003db fy √fc
but ld not be less than 8 in (20.3 cm) or 0.0003fy db.
CRACK CONTROL OF FLEXURAL MEMBERS Because of the risk of large cracks opening up when reinforcement is subjected to high stresses, the ACI Code recommends that designs be based on a steel yield strength fy no larger than 80 ksi (551.6 MPa). When design is based on a yield strength fy greater than 40 ksi (275.8 MPa), the cross sections of maximum positive and negative moment should be proportioned for crack control so that specific limits are satisfied by
R F s m r
3
z fs √dc A where fs calculated stress, ksi (MPa), in reinforcement at service loads TLFeBOOK
w v l
40816_05a_p147-195 170
10/22/01
12:45 PM
40816 HICKS Mcghp Chap_05 Pgs 171 7/10/2001
CONCRETE FORMULAS
d
s
Page 171
171
dc thickness of concrete cover, in (mm), measured from extreme tension surface to center of bar closest to that surface A effective tension area of concrete, in2 (mm2) per bar. This area should be taken as that surrounding main tension reinforcement, having the same centroid as that reinforcement, multiplied by the ratio of the area of the largest bar used to the total area of tension reinforcement These limits are z 175 kip/in (30.6 kN/mm) for interior exposures and z 145 kip/in (25.3 kN/mm) for exterior exposures. These correspond to limiting crack widths of 0.016 to 0.013 in (0.406 to 0.33 mm), respectively, at the extreme tension edge under service loads. In the equation for z, fs should be computed by dividing the bending moment by the product of the steel area and the internal moment arm, but fs may be taken as 60 percent of the steel yield strength without computation.
o n s d e
REQUIRED STRENGTH For combinations of loads, the ACI Code requires that a structure and its members should have the following ultimate strengths (capacities to resist design loads and their related internal moments and forces): With wind and earthquake loads not applied, U 1.4D 1.7L
t
where D effect of basic load consisting of dead load plus volume change (shrinkage, temperature) and L effect of live load plus impact. TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 172
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 172
172
CHAPTER FIVE
When wind loads are applied, the largest of the preceeding equation and the two following equations determine the required strength: U 0.75(1.4D 1.7L 1.7W ) U 0.9D 1.3W where W effect of wind load. If the structure can be subjected to earthquake forces E, substitute 1.1E for W in the preceding equation. Where the effects of differential settlement, creep, shrinkage, or temperature change may be critical to the structure, they should be included with the dead load D, and the strength should be at least equal to U 0.75(1.4D 1.7L) 1.4(D T ) where T cumulative effects of temperature, creep, shrinkage, and differential settlement.
DEFLECTION COMPUTATIONS AND CRITERIA FOR CONCRETE BEAMS
MM I 1 MM I cr a
3
g
cr a
3
cr
w i d d o s
U O T
The assumptions of working-stress theory may also be used for computing deflections under service loads; that is, elastictheory deflection formulas may be used for reinforced-concrete beams. In these formulas, the effective moment of inertia Ic is given by Ie
g f
Ig
where Ig moment of inertia of the gross concrete section TLFeBOOK
G f w c m t f b
40816_05a_p147-195 172
10/22/01
12:45 PM
Page 173
40816 HICKS Mcghp Chap_05 Pgs 173 7/10/2001
CONCRETE FORMULAS
e
173
Mcr cracking moment Ma moment for which deflection is being computed Icr cracked concrete (transformed) section If yt is taken as the distance from the centroidal axis of the gross section, neglecting the reinforcement, to the extreme surface in tension, the cracking moment may be computed from
, , e
,
Mcr
fr Ig yt
with the modulus of rupture of the concrete fr 7.5√fc . The deflections thus calculated are those assumed to occur immediately on application of load. Additional long-time deflections can be estimated by multiplying the immediate deflection by 2 when there is no compression reinforcement or by 2 1.2A/A s s 0.6, where As is the area of compression reinforcement and As is the area of tension reinforcement.
ULTIMATE-STRENGTH DESIGN OF RECTANGULAR BEAMS WITH TENSION REINFORCEMENT ONLY d e c
n
Generally, the area As of tension reinforcement in a reinforced-concrete beam is represented by the ratio As /bd, where b is the beam width and d is the distance from extreme compression surface to the centroid of tension reinforcement. At ultimate strength, the steel at a critical section of the beam is at its yield strength fy if the concrete does not fail in compression first. Total tension in the steel then will be As f y fy bd. It is opposed, by an equal compressive force: TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 174
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 174
174
CHAPTER FIVE
0.85 fcba 0.85 fcb1c where fc 28-day strength of the concrete, ksi (MPa) a depth of the equivalent rectangular stress distribution
M
c distance from the extreme compression surface to the neutral axis
F i
1 a constant Equating the compression and tension at the critical section yields c
pfy d 0.851 fc
w
The criterion for compression failure is that the maximum strain in the concrete equals 0.003 in/in (0.076 mm/mm). In that case, c
S T t a m a
0.003 d fs /Es 0.003
where fs steel stress, ksi (MPa) Es modulus of elasticity of steel 29,000 ksi (199.9 GPa)
Balanced Reinforcing Under balanced conditions, the concrete reaches its maximum strain of 0.003 when the steel reaches its yield strength fy. This determines the steel ratio for balanced conditions: TLFeBOOK
w t s e T e a a
40816_05a_p147-195 174
10/22/01
12:45 PM
Page 175
40816 HICKS Mcghp Chap_05 Pgs 175 7/10/2001
CONCRETE FORMULAS
0.851 fc 87,000 fy 87,000 fy
b s -
175
Moment Capacity For such underreinforced beams, the bending-moment capacity of ultimate strength is M u 0.90[bd 2 fc(1 0.59)]
n
0.90 As fy d
a 2
where fy /fc and a As fy /0.85fc. m n
Shear Reinforcement The ultimate shear capacity Vn of a section of a beam equals the sum of the nominal shear strength of the concrete Vc and the nominal shear strength provided by the reinforcement Vs; that is, Vn Vc Vs. The factored shear force Vu on a section should not exceed Vn (Vc Vs)
h
where capacity reduction factor (0.85 for shear and torsion). Except for brackets and other short cantilevers, the section for maximum shear may be taken at a distance equal to d from the face of the support. The shear Vc carried by the concrete alone should not exceed 2√fc bw d, where bw is the width of the beam web and d, the depth of the centroid of reinforcement. (As an alternative, the maximum for Vc may be taken as TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 176
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 176
176
CHAPTER FIVE
Vc 1.9 √fc2500w
Vud Mu
b d w
3.5 √fcbw d where w As/bwd and Vu and Mu are the shear and bending moment, respectively, at the section considered, but Mu should not be less than Vud.) When Vu is larger than Vc, the excess shear has to be resisted by web reinforcement. The area of steel required in vertical stirrups, in2 (mm2), per stirrup, with a spacing s, in (mm), is VS Av s fy d where fy yield strength of the shear reinforcement. Av is the area of the stirrups cut by a horizontal plane. Vs should not exceed 8√fc bw d in sections with web reinforcement, and fy should not exceed 60 ksi (413.7 MPa). Where shear reinforcement is required and is placed perpendicular to the axis of the member, it should not be spaced farther apart than 0.5d, or more than 24 in (609.6 mm) c to c. When Vs exceeds 4√fc bw d, however, the maximum spacing should be limited to 0.25d. Alternatively, for practical design, to indicate the stirrup spacing s for the design shear Vu, stirrup area Av, and geometry of the member bw and d, s
i b w f
a V
D A s f f ( o t
w
Avfyd Vu 2√fc bw d
The area required when a single bar or a single group of parallel bars are all bent up at the same distance from the support at angle with the longitudinal axis of the member is TLFeBOOK
40816_05a_p147-195 176
10/22/01
12:45 PM
Page 177
40816 HICKS Mcghp Chap_05 Pgs 177 7/10/2001
CONCRETE FORMULAS
Av
u
e ,
s d , r e t Vs d p -
177
Vs fy sin
in which Vs should not exceed 3√fc bw d. Av is the area cut by a plane normal to the axis of the bars. The area required when a series of such bars are bent up at different distances from the support or when inclined stirrups are used is Av
Vs s (sin cos )fy d
A minimum area of shear reinforcement is required in all members, except slabs, footings, and joists or where Vu is less than 0.5Vc.
Development of Tensile Reinforcement At least one-third of the positive-moment reinforcement in simple beams and one-fourth of the positive-moment reinforcement in continuous beams should extend along the same face of the member into the support, in both cases, at least 6 in (152.4 mm) into the support. At simple supports and at points of inflection, the diameter of the reinforcement should be limited to a diameter such that the development length ld satisfies ld
Mn la Vu
where Mn computed flexural strength with all reinforcing steel at section stressed to fy f s
Vu applied shear at section la additional embedment length beyond inflection point or center of support TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 178
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 178
178
CHAPTER FIVE
At an inflection point, la is limited to a maximum of d, the depth of the centroid of the reinforcement, or 12 times the reinforcement diameter.
Hooks on Bars The basic development length for a hooked bar with fy 60 ksi (413.7 MPa) is defined as lhb
1200db √fc
s (
where db is the bar diameter, in (mm), and fc is the 28-day compressive strength of the concrete, lb/in2 (MPa). W l b t
WORKING-STRESS DESIGN OF RECTANGULAR BEAMS WITH TENSION REINFORCEMENT ONLY From the assumption that stress varies across a beam section with the distance from the neutral axis, it follows that
A n fc k fs 1k
T
where n modular ratio Es /Ec Es modulus of elasticity of steel reinforcement, ksi (MPa) Ec modulus of elasticity of concrete, ksi (MPa) TLFeBOOK
w
w
40816_05a_p147-195 178
10/22/01
12:45 PM
Page 179
40816 HICKS Mcghp Chap_05 Pgs 179 7/10/2001
CONCRETE FORMULAS
e e
179
fc compressive stress in extreme surface of concrete, ksi (MPa) fs stress in steel, ksi (MPa) kd distance from extreme compression surface to neutral axis, in (mm)
0
d distance from extreme compression to centroid of reinforcement, in (mm) When the steel ratio As /bd, where As area of tension reinforcement, in2 (mm2), and b beam width, in (mm), is known, k can be computed from
y
k √2n (n)2 n Wherever positive-moment steel is required, should be at least 200/fy, where fy is the steel yield stress. The distance jd between the centroid of compression and the centroid of tension, in (mm), can be obtained from j1
k 3
t Allowable Bending Moment The moment resistance of the concrete, inkip (k Nm) is M c 12 fckjbd 2 K cbd 2 , )
where Kc 12 fc kj. The moment resistance of the steel is M s fs As jd fsjbd 2 K sbd 2 where Ks fsj. TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 180
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 180
180
CHAPTER FIVE
Allowable Shear The nominal unit shear stress acting on a section with shear V is v
V bd
Allowable shear stresses are 55 percent of those for ultimate-strength design. Otherwise, designs for shear by the working-stress and ultimate-strength methods are the same. Except for brackets and other short cantilevers, the section for maximum shear may be taken at a distance d from the face of the support. In working-stress design, the shear stress vc carried by the concrete alone should not exceed 1.1 √fc . (As an alternative, the maximum for vc may be taken as √fc 1300Vd/M , with a maximum of 1.9 √fc ; fc is the 28-day compressive strength of the concrete, lb/in2 (MPa), and M is the bending moment at the section but should not be less than Vd.) At cross sections where the torsional stress vt exceeds 0.825√fc , vc should not exceed vc
1.1√f c √1 (vt /1.2v)2
a d
F d
S e o t
w
The excess shear v vc should not exceed 4.4√fc in sections with web reinforcement. Stirrups and bent bars should be capable of resisting the excess shear V V vc bd. The area required in the legs of a vertical stirrup, in2 (mm2), is Av
w s
Vs fv d TLFeBOOK
S t s m
40816_05a_p147-195 180
10/22/01
12:45 PM
Page 181
40816 HICKS Mcghp Chap_05 Pgs 181 7/10/2001
CONCRETE FORMULAS
r
where s spacing of stirrups, in (mm); and fv allowable stress in stirrup steel, (lb/in2) (MPa). For a single bent bar or a single group of parallel bars all bent at an angle with the longitudinal axis at the same distance from the support, the required area is Av
r y e e d e d n s 2
t
181
V fv sin
For inclined stirrups and groups of bars bent up at different distances from the support, the required area is Av
Vs fv d(sin cos )
Stirrups in excess of those normally required are provided each way from the cutoff for a distance equal to 75 percent of the effective depth of the member. Area and spacing of the excess stirrups should be such that
s Av 60
bws fy
where Av stirrup cross-sectional area, in2 (mm2) bw web width, in (mm) d
s stirrup spacing, in (mm)
2
fy yield strength of stirrup steel, (lb/in2) (MPa) Stirrup spacing s should not exceed d/8b, where b is the ratio of the area of bars cut off to the total area of tension bars at the section and d is the effective depth of the member. TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 182
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 182
182
CHAPTER FIVE
ULTIMATE-STRENGTH DESIGN OF RECTANGULAR BEAMS WITH COMPRESSION BARS
w
The bending-moment capacity of a rectangular beam with both tension and compression steel is
M u 0.90 (As A) s fy d
a 2
A f (d d) s y
where a depth of equivalent rectangular compressive stress distribution (As A)f s y /fcb
W R C T s u
b width of beam, in (mm) d distance from extreme compression surface to centroid of tensile steel, in (mm)
w
d distance from extreme compression surface to centroid of compressive steel, in (mm) As area of tensile steel, in2 (mm2) As area of compressive steel, in2 (mm2) fy yield strength of steel, ksi (MPa) fc 28-day strength of concrete, ksi (MPa)
w
This is valid only when the compressive steel reaches fy and occurs when ( ) 0.851
f c d 87,000 fy d 87,000 fy TLFeBOOK
40816_05a_p147-195 182
10/22/01
12:45 PM
Page 183
40816 HICKS Mcghp Chap_05 Pgs 183 7/10/2001
CONCRETE FORMULAS
183
where As /bd As /bd 1 a constant h
WORKING-STRESS DESIGN OF RECTANGULAR BEAMS WITH COMPRESSION BARS e The following formulas, based on the linear variation of stress and strain with distance from the neutral axis, may be used in design: k
o
1 1 fs /nfc
where fs stress in tensile steel, ksi (MPa) o
fc stress in extreme compression surface, ksi (MPa) n modular ratio, Es /Ec fs where
d
kd d 2f d kd s
fs stress in compressive steel, ksi (MPa) d distance from extreme compression surface to centroid of tensile steel, in (mm) d distance from extreme compression surface to centroid of compressive steel, in (mm) TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 184
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 184
184
CHAPTER FIVE
The factor 2 is incorporated into the preceding equation in accordance with ACI 318, “Building Code Requirements for Reinforced Concrete,” to account for the effects of creep and nonlinearity of the stress–strain diagram for concrete. However, fs should not exceed the allowable tensile stress for the steel. Because total compressive force equals total tensile force on a section, C Cc Cs T
w s r
w u s
where C total compression on beam cross section, kip (N) Cc total compression on concrete, kip (N) at section Cs force acting on compressive steel, kip (N) T force acting on tensile steel, kip (N) l m
k fs fc 2[ (kd d)/(d kd )] where As /bd and A/bd . s For reviewing a design, the following formulas may be used: k
√
z
(k 3d / 3) 4nd[k (d/d )] k 2 4n[k (d/d )]
2n
d d
n ( ) n( ) 2
w
2
jd d z TLFeBOOK
40816_05a_p147-195 184
10/22/01
12:45 PM
Page 185
40816 HICKS Mcghp Chap_05 Pgs 185 7/10/2001
185
CONCRETE FORMULAS
n s f e
where jd is the distance between the centroid of compression and the centroid of the tensile steel. The moment resistance of the tensile steel is Ms Tjd As fs jd
fs
e
M As jd
where M is the bending moment at the section of beam under consideration. The moment resistance in compression is , Mc
1 d f jbd 2 k 2n 1 2 c kd
t fc
2M jbd {k 2n[1 d/kd )]} 2
Computer software is available for the preceding calculations. Many designers, however, prefer the following approximate formulas: M1 e
1 kd fc bkd d 2 3
d ) Ms M M 1 2 fsA(d s where M bending moment Ms moment-resisting capacity of compressive steel M1 moment-resisting capacity of concrete TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 186
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 186
186
CHAPTER FIVE
ULTIMATE-STRENGTH DESIGN OF I AND T BEAMS
T t
When the neutral axis lies in the flange, the member may be designed as a rectangular beam, with effective width b and depth d. For that condition, the flange thickness t will be greater than the distance c from the extreme compression surface to the neutral axis, c
W I F d d o ( r
1.18 d 1
where 1 constant As fy /bd fc As area of tensile steel, in2 (mm2)
b t b c
fy yield strength of steel, ksi (MPa) fc 28-day strength of concrete, ksi (MPa) When the neutral axis lies in the web, the ultimate moment should not exceed
Mu 0.90 (As Asf ) fy d
a t Asf fy d 2 2
(8.51)
where Asf area of tensile steel required to develop compressive strength of overhanging flange, in2 (mm2) 0.85(b bw)tfc/ fy bw width of beam web or stem, in (mm) a depth of equivalent rectangular compressive stress distribution, in (mm) (As Asf)fy / 0.85 fc bw TLFeBOOK
w
40816_05a_p147-195 186
10/22/01
12:45 PM
Page 187
40816 HICKS Mcghp Chap_05 Pgs 187 7/10/2001
CONCRETE FORMULAS
187
The quantity w f should not exceed 0.75b, where b is the steel ratio for balanced conditions w As /bwd, and f Asf /bw d. e d e n
WORKING-STRESS DESIGN OF I AND T BEAMS For T beams, effective width of compression flange is determined by the same rules as for ultimate-strength design. Also, for working-stress design, two cases may occur: the neutral axis may lie in the flange or in the web. (For negative moment, a T beam should be designed as a rectangular beam with width b equal to that of the stem.) If the neutral axis lies in the flange, a T or I beam may be designed as a rectangular beam with effective width b. If the neutral axis lies in the web or stem, an I or T beam may be designed by the following formulas, which ignore the compression in the stem, as is customary:
t k
I 1 fs /nfc
where kd distance from extreme compression surface to neutral axis, in (mm) 2
d distance from extreme compression surface to centroid of tensile steel, in (mm) fs stress in tensile steel, ksi (MPa)
e
fc stress in concrete at extreme compression surface, ksi (MPa) n modular ratio Es /Ec TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 188
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 188
188
CHAPTER FIVE
Because the total compressive force C equals the total tension T, C
bt 1 f (2kd t) T As fs 2 c kd
U F
2ndAs bt 2 kd 2nAs 2bt where As area of tensile steel, in2 (mm2); and t flange thickness, in (mm). The distance between the centroid of the area in compression and the centroid of the tensile steel is z
jd d z
d f
t (3kd 2t) 3(2kd t)
W l r
l r t
The moment resistance of the steel is Ms Tjd As fs jd The moment resistance of the concrete is Mc Cjd
fc btjd (2kd t) 2kd
w t
In design, Ms and Mc can be approximated by
m
t Ms As fs d 2 Mc
1 t fc bt d 2 2
w
TLFeBOOK
40816_05a_p147-195 188
10/22/01
12:45 PM
Page 189
40816 HICKS Mcghp Chap_05 Pgs 189 7/10/2001
CONCRETE FORMULAS
l
189
derived by substituting d t/2 for jd and fc /2 for fc(1 t/2kd), the average compressive stress on the section.
ULTIMATE-STRENGTH DESIGN FOR TORSION
e
When the ultimate torsion Tu is less than the value calculated from the Tu equation that follows, the area Av of shear reinforcement should be at least
Av 50
bw s fy
However, when the ultimate torsion exceeds Tu calculated from the Tu equation that follows, and where web reinforcement is required, either nominally or by calculation, the minimum area of closed stirrups required is Av 2At
50bw s fy
where At is the area of one leg of a closed stirrup resisting torsion within a distance s. Torsion effects should be considered whenever the ultimate torsion exceeds Tu 0.5 √fc x2y where capacity reduction factor 0.85 Tu ultimate design torsional moment TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 190
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 190
190
CHAPTER FIVE
x2y sum for component rectangles of section of product of square of shorter side and longer side of each rectangle (where T section applies, overhanging flange width used in design should not exceed three times flange thickness) The torsion Tc carried by the concrete alone should not exceed Tc
n N s t o
0.8√f c x2y
√1 (0.4Vu /Ct Tu )2
where Ct bwd / x2y. Spacing of closed stirrups for torsion should be computed from s
At fy t x1 y1 (Tu Tc)
I b
where At area of one leg of closed stirrup t 0.66 0.33y1/x1 but not more than 1.50 fy yield strength of torsion reinforcement x1 shorter dimension c to c of legs of closed stirrup y1 longer dimension c to c of legs of closed stirrup The spacing of closed stirrups, however, should not exceed (x1 y1)/4 or 12 in (304.8 mm). Torsion reinforcement should be provided over at least a distance of d b beyond the point where it is theoretically required, where b is the beam width. TLFeBOOK
W T T
w t l o
40816_05a_p147-195 190
10/22/01
12:45 PM
Page 191
40816 HICKS Mcghp Chap_05 Pgs 191 7/10/2001
191
CONCRETE FORMULAS
f r , d
At least one longitudinal bar should be placed in each corner of the stirrups. Size of longitudinal bars should be at least No. 3, and their spacing around the perimeters of the stirrups should not exceed 12 in (304.8 mm). Longitudinal bars larger than No. 3 are required if indicated by the larger of the values of Al computed from the following two equations:
t Al 2At Al -
x 1 y1 s
(T TV /3C ) 400xs f u
y
u
u
t
x s y
2At
1
1
In the second of the preceding two equations 50bws /fy may be substituted for 2At. The maximum allowable torsion is Tu 5Tc.
d
WORKING-STRESS DESIGN FOR TORSION
d
Torsion effects should be considered whenever the torsion T due to service loads exceeds
d t d e
T 0.55(0.5 fc x2y) where x2y sum for the component rectangles of the section of the product of the square of the shorter side and the longer side of each rectangle. The allowable torsion stress on the concrete is 55 percent of that computed from the TLFeBOOK
40816_05a_p147-195
10/22/01
12:45 PM
Page 192
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 192
192
CHAPTER FIVE
preceding Tc equation. Spacing of closed stirrups for torsion should be computed from s
3At t x1 y1 fv (vt vtc) x2y
where At area of one leg of closed stirrup t 0.66
0.33y1 , but not more than 1.50 x1
tc allowable torsion stress on concrete x1 shorter dimension c to c of legs of closed stirrup y1 longer dimension c to c of legs of closed stirrup
FLAT-SLAB CONSTRUCTION Slabs supported directly on columns, without beams or girders, are classified as flat slabs. Generally, the columns flare out at the top in capitals (Fig. 5.3). However, only the portion of the inverted truncated cone thus formed that lies inside a 90° vertex angle is considered effective in resisting stress. Sometimes, the capital for an exterior column is a bracket on the inner face. The slab may be solid, hollow, or waffle. A waffle slab usually is the most economical type for long spans, although formwork may be more expensive than for a solid slab. A waffle slab omits much of the concrete that would be in tension and thus is not considered effective in resisting stresses. TLFeBOOK
192
-
d
d
r s e s g a
b h A .
10/22/01 12:45 PM Page 193
TLFeBOOK
40816_05a_p147-195
40816 HICKS Mcghp Chap_05 Pgs 193 7/10/2001
193 FIGURE 5.3 Concrete flat slab: (a) Vertical section through drop panel and column at a support. (b) Plan view indicates division of slab into column and middle strips.
40816_05a_p147-195
10/22/01
12:45 PM
Page 194
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 p. 194
194
CHAPTER FIVE
To control deflection, the ACI Code establishes minimum thicknesses for slabs, as indicated by the following equation: h
l n(0.8 fy /200,000) 36 5[m 0.12(1 1/)]
S (
l n(0.8 fy /200,000) 36 9
F
where h slab thickness, in (mm) ln length of clear span in long direction, in (mm) fy yield strength of reinforcement, ksi (MPa) ratio of clear span in long direction to clear span in the short direction m average value of for all beams on the edges of a panel ratio of flexural stiffness Ecb Ib of beam section to flexural stiffness Ecs Is of width of slab bounded laterally by centerline of adjacent panel, if any, on each side of beam
F c c c T e s t c t l e
Ecb modulus of elasticity of beam concrete Ecs modulus of elasticity of slab concrete
D
Ib moment of inertia about centroidal axis of gross section of beam, including that portion of slab on each side of beam that extends a distance equal to the projection of the beam above or below the slab, whichever is greater, but not more than four times slab thickness TLFeBOOK
T
40816_05a_p147-195 194
10/22/01
12:45 PM
Page 195
40816 HICKS Mcghp Chap_05 Pgs 195 7/10/2001
CONCRETE FORMULAS
m :
195
Is moment of inertia about centroidal axis of gross section of slab h3/12 times slab width specified in definition of Slab thickness h, however, need not be larger than (ln /36) (0.8 fy /200,000).
FLAT-PLATE CONSTRUCTION )
r s n b t
Flat slabs with constant thickness between supports are called flat plates. Generally, capitals are omitted from the columns. Exact analysis or design of flat slabs or flat plates is very complex. It is common practice to use approximate methods. The ACI Code presents two such methods: direct design and equivalent frame. In both methods, a flat slab is considered to consist of strips parallel to column lines in two perpendicular directions. In each direction, a column strip spans between columns and has a width of one-fourth the shorter of the two perpendicular spans on each side of the column centerline. The portion of a slab between parallel column strips in each panel is called the middle strip (see Fig. 5.3).
Direct Design Method f f e t
This may be used when all the following conditions exist: The slab has three or more bays in each direction. Ratio of length to width of panel is 2 or less. Loads are uniformly distributed over the panel. TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 196
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 196
196
CHAPTER FIVE
Ratio of live to dead load is 3 or less. Columns form an approximately rectangular grid (10 percent maximum offset). Successive spans in each direction do not differ by more than one-third of the longer span. When a panel is supported by beams on all sides, the relative stiffness of the beams satisfies 0.2
1 2
ll 5 2
2
v o 1
w
1
where 1 in direction of l1 2 in direction of l2 relative beam stiffness defined in the preceding equation l1 span in the direction in which moments are being determined, c to c of supports l2 span perpendicular to l1, c to c of supports
2
The basic equation used in direct design is the total static design moment in a strip bounded laterally by the centerline of the panel on each side of the centerline of the supports: Mo
wl2l2n 8
where w uniform design load per unit of slab area and ln clear span in direction moments are being determined. The strip, with width l2, should be designed for bending moments for which the sum in each span of the absolute TLFeBOOK
S S a
40816_05b_p196-212 s 196
10/22/01
12:46 PM
Page 197
40816 HICKS Mcghp Chap_05 Pgs 197 7/10/2001
197
CONCRETE FORMULAS
d
values of the positive and average negative moments equals or exceeds Mo.
e
1. The sum of the flexural stiffnesses of the columns above and below the slab Kc should be such that
e
c
Kc min (Ks Kb)
where Kc flexural stiffness of column EccIc Ecc modulus of elasticity of column concrete Ic moment of inertia about centroidal axis of gross section of column -
Ks Ecs Is Kb Ecb Ib
e
l e
d . g e
min minimum value of c as given in engineering handbooks 2. If the columns do not satisfy condition 1, the design positive moments in the panels should be multiplied by the coefficient: s 1
2 a 4 a
1 c
min
SHEAR IN SLABS Slabs should also be investigated for shear, both beam type and punching shear. For beam-type shear, the slab is considered TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 198
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 198
198
CHAPTER FIVE
as a thin, wide rectangular beam. The critical section for diagonal tension should be taken at a distance from the face of the column or capital equal to the effective depth d of the slab. The critical section extends across the full width b of the slab. Across this section, the nominal shear stress vu on the unreinforced concrete should not exceed the ultimate capacity 2√f c or the allowable working stress 1.1√fc , where fc is the 28-day compressive strength of the concrete, lb/in2 (MPa). Punching shear may occur along several sections extending completely around the support, for example, around the face of the column or column capital or around the drop panel. These critical sections occur at a distance d/2 from the faces of the supports, where d is the effective depth of the slab or drop panel. Design for punching shear should be based on Vn (Vc VS) where capacity reduction factor (0.85 for shear and torsion), with shear strength Vn taken not larger than the concrete strength Vc calculated from
Vc 2
4 c
b t E m t
C A s a a f t p t b
√f b d 4 √f b d c
o
c
o
where bo perimeter of critical section and c ratio of long side to short side of critical section. However, if shear reinforcement is provided, the allowable shear may be increased a maximum of 50 percent if shear reinforcement consisting of bars is used and increased a maximum of 75 percent if shearheads consisting of two pairs of steel shapes are used. Shear reinforcement for slabs generally consists of bent bars and is designed in accordance with the provisions for TLFeBOOK
w d b t i a
40816_05b_p196-212 s 198
10/22/01
12:46 PM
40816 HICKS Mcghp Chap_05 Pgs 199 7/10/2001
199
CONCRETE FORMULAS
r e d l r d s e
Page 199
beams with the shear strength of the concrete at critical sections taken as 2√f c bo d at ultimate strength and Vn 6√fcbo d. Extreme care should be taken to ensure that shear reinforcement is accurately placed and properly anchored, especially in thin slabs.
COLUMN MOMENTS s , d e e r
d e
Another important consideration in design of two-way slab systems is the transfer of moments to columns. This is generally a critical condition at edge columns, where the unbalanced slab moment is very high due to the one-sided panel. The unbalanced slab moment is considered to be transferred to the column partly by flexure across a critical section, which is d/2 from the periphery of the column, and partly by eccentric shear forces acting about the centroid of the critical section. That portion of unbalanced slab moment Mu transferred by the eccentricity of the shear is given by Mu: 1
v 1 1 f f d o t r
√ bb 2 3
1 2
where b1 width, in (mm), of critical section in the span direction for which moments are being computed; and b2 width, in (mm), of critical section in the span direction perpendicular to b1. As the width of the critical section resisting moment increases (rectangular column), that portion of the unbalanced moment transferred by flexure also increases. The TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 200
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 200
200
CHAPTER FIVE
maximum factored shear, which is determined by combining the vertical load and that portion of shear due to the unbalanced moment being transferred, should not exceed Vc, with Vc given by preceding the Vc equation. The shear due to moment transfer can be determined at the critical section by treating this section as an analogous tube with thickness d subjected to a bending moment Mu. The shear stress at the crack, at the face of the column or bracket support, is limited to 0.2 fc or a maximum of 800 Ac, where Ac is the area of the concrete section resisting shear transfer. The area of shear-friction reinforcement Avf required in addition to reinforcement provided to take the direct tension due to temperature changes or shrinkage should be computed from Avf
b a n C s c
w
Vu fy
where Vu is the design shear, kip (kN), at the section; fy is the reinforcement yield strength, but not more than 60 ksi (413.7 MPa); and , the coefficient of friction, is 1.4 for monolithic concrete, 1.0 for concrete placed against hardened concrete, and 0.7 for concrete placed against structural rolled-steel members. The shear-friction reinforcement should be well distributed across the face of the crack and properly anchored at each side.
SPIRALS This type of transverse reinforcement should be at least 8 in (9.5 mm) in diameter. A spiral may be anchored at each of its ends by 112 extra turns of the spiral. Splices may
B A u c e r a c
3
TLFeBOOK
f
40816_05b_p196-212 s 200
10/22/01
12:46 PM
Page 201
40816 HICKS Mcghp Chap_05 Pgs 201 7/10/2001
201
CONCRETE FORMULAS
e d r l h n 0 g o
be made by welding or by a lap of 48 bar diameters, but at least 12 in (304.8 mm). Spacing (pitch) of spirals should not exceed 3 in (76.2 mm), or be less than 1 in (25.4 mm). Clear spacing should be at least 113 times the maximum size of coarse aggregate. The ratio of the volume of spiral steel/volume of concrete core (out to out of spiral) should be at least s 0.45
AA
g c
ff
1
c
y
where Ag gross area of column Ac core area of column measured to outside of spiral fy spiral steel yield strength
s i r l d y
t t y
fc 28-day compressive strength of concrete
BRACED AND UNBRACED FRAMES As a guide in judging whether a frame is braced or unbraced, note that the commentary on ACI 31883 indicates that a frame may be considered braced if the bracing elements, such as shear walls, shear trusses, or other means resisting lateral movement in a story, have a total stiffness at least six times the sum of the stiffnesses of all the columns resisting lateral movement in that story. The slenderness effect may be neglected under the two following conditions: TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 202
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 202
202
CHAPTER FIVE
For columns braced against sidesway, when
w
klu M 34 12 1 r M2 where M1 smaller of two end moments on column as determined by conventional elastic frame analysis, with positive sign if column is bent in single curvature and negative sign if column is bent in double curvature; and M2 absolute value of larger of the two end moments on column as determined by conventional elastic frame analysis. For columns not braced against sidesway, when klu 22 r
F w s t
LOAD-BEARING WALLS These are subject to axial compression loads in addition to their own weight and, where there is eccentricity of load or lateral loads, to flexure. Load-bearing walls may be designed in a manner similar to that for columns but including the design requirements for non-load-bearing walls. As an alternative, load-bearing walls may be designed by an empirical procedure given in the ACI Code when the eccentricity of the resulting compressive load is equal to or less than one-sixth the thickness of the wall. Load-bearing walls designed by either method should meet the minimum reinforcing requirements for non-loadbearing walls. In the empirical method the axial capacity, kip (kN), of the wall is klc 2 Pn 0.55 fc Ag 1 32h
TLFeBOOK
S W w b c
w
40816_05b_p196-212 s 202
10/22/01
12:46 PM
Page 203
40816 HICKS Mcghp Chap_05 Pgs 203 7/10/2001
CONCRETE FORMULAS
where
203
fc 28-day compressive strength of concrete, ksi (MPa) Ag gross area of wall section, in2 (mm2)
s h n
strength reduction factor 0.70 lc vertical distance between supports, in (mm) h overall thickness of wall, in (mm) k effective-length factor For a wall supporting a concentrated load, the length of wall effective for the support of that concentrated load should be taken as the smaller of the distance center to center between loads and the bearing width plus 4h.
o r e d e r
SHEAR WALLS Walls subject to horizontal shear forces in the plane of the wall should, in addition to satisfying flexural requirements, be capable of resisting the shear. The nominal shear stress can be computed from vu
d f
Vu hd
where Vu total design shear force capacity reduction factor 0.85 d 0.8lw TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 204
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 204
204
CHAPTER FIVE
h overall thickness of wall lw horizontal length of wall The shear Vc carried by the concrete depends on whether Nu, the design axial load, lb (N), normal to the wall horizontal cross section and occurring simultaneously with Vu at the section, is a compression or tension force. When Nu is a compression force, Vc may be taken as 2√fc hd, where fc is the 28-day strength of concrete, lb/in2 (MPa). When Nu is a tension force, Vc should be taken as the smaller of the values calculated from
Vc 3.3 √fc hd
Vc hd 0.6√fc
w f t t r
Nu d 4lw
lw(1.25 √fc 0.2Nu /lwh) Mu /Vu lw /2
This equation does not apply, however, when Mu/Vu lw /2 is negative. When the factored shear Vu is less than 0.5Vc, reinforcement should be provided as required by the empirical method for bearing walls. When Vu exceeds 0.5Vc, horizontal reinforcement should be provided with Vs Av fy d/s2, where s2 spacing of horizontal reinforcement, and Av reinforcement area. Also, the ratio h of horizontal shear reinforcement, to the gross concrete area of the vertical section of the wall should be at least 0.0025. Spacing of horizontal shear bars should not exceed lw /5, 3h, or 18 in (457.2 mm). In addition, the ratio of vertical shear reinforcement area to gross concrete area of the horizontal section of wall does not need to be greater than that required for horizontal reinforcement but should not be less than TLFeBOOK
w m s t t f
C F w p a
40816_05b_p196-212 s 204
10/22/01
12:46 PM
Page 205
40816 HICKS Mcghp Chap_05 Pgs 205 7/10/2001
205
CONCRETE FORMULAS
n 0.0025 0.5 2.5 n l h n , . r
where hw total height of wall. Spacing of vertical shear reinforcement should not exceed lw /3, 3h, or 18 in (457.2 mm). In no case should the shear strength Vn be taken greater than 10√f c hd at any section. Bearing stress on the concrete from anchorages of posttensioned members with adequate reinforcement in the end region should not exceed fb calculated from
√
Ab 0.2 1.25 fci Ab
fb 0.6 √fc
l d e e . r n -
(h 0.0025) 0.0025
fb 0.8 fc
2
hw lw
√
Ab fc Ab
where Ab bearing area of anchor plate, and Ab maximum area of portion of anchorage surface geometrically similar to and concentric with area of anchor plate. A more refined analysis may be applied in the design of the end-anchorage regions of prestressed members to develop the ultimate strength of the tendons. should be taken as 0.90 for the concrete.
CONCRETE GRAVITY RETAINING WALLS Forces acting on gravity walls include the weight of the wall, weight of the earth on the sloping back and heel, lateral earth pressure, and resultant soil pressure on the base. It is advisable to include a force at the top of the wall to account for TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 206
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 206
206
CHAPTER FIVE
frost action, perhaps 700 lb/linear ft (1042 kg/m). A wall, consequently, may fail by overturning or sliding, overstressing of the concrete or settlement due to crushing of the soil. Design usually starts with selection of a trial shape and dimensions, and this configuration is checked for stability. For convenience, when the wall is of constant height, a 1-ft (0.305 m) long section may be analyzed. Moments are taken about the toe. The sum of the righting moments should be at least 1.5 times the sum of the overturning moments. To prevent sliding,
F ( t t
R v 1.5Ph where coefficient of sliding friction Rv total downward force on soil, lb (N) Ph horizontal component of earth thrust, lb (N) Next, the location of the vertical resultant Rv should be found at various sections of the wall by taking moments about the toe and dividing the sum by Rv. The resultant should act within the middle third of each section if there is to be no tension in the wall. Finally, the pressure exerted by the base on the soil should be computed to ensure that the allowable pressure is not exceeded. When the resultant is within the middle third, the pressures, lb/ft2 (Pa), under the ends of the base are given by p
Mc R Rv v A I A
1 6eL
where A area of base, ft2 (m2) L width of base, ft (m) e distance, parallel to L, from centroid of base to Rv, ft (m) TLFeBOOK
F w c
40816_05b_p196-212 s 206
10/22/01
12:46 PM
40816 HICKS Mcghp Chap_05 Pgs 207 7/10/2001
CONCRETE FORMULAS
, . d . t n t -
Page 207
207
Figure 5.4 shows the pressure distribution under a 1-ft (0.305-m) strip of wall for e L/2 a, where a is the distance of Rv from the toe. When Rv is exactly L/3 from the toe, the pressure at the heel becomes zero (Fig. 5.4c). When
) e s t s d t e y
e
FIGURE 5.4 Diagrams for pressure of the base of a concrete gravity wall on the soil below. (a) Vertical section through the wall. (b) Significant compression under the entire base.
TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 208
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 208
208
CHAPTER FIVE
FIGURE 5.4 (Continued) Diagrams for pressure of the base of a concrete wall on the soil below. (c) No compression along one edge of the base. (d) Compression only under part of the base. No support from the soil under the rest of the beam.
F r
Rv falls outside the middle third, the pressure vanishes under a zone around the heel, and pressure at the toe is much larger than for the other cases (Fig. 5.4d).
b f g f
CANTILEVER RETAINING WALLS
m o o
This type of wall resists the lateral thrust of earth pressure through cantilever action of a vertical stem and horizontal TLFeBOOK
40816_05b_p196-212 s 208
10/22/01
12:46 PM
Page 209
40816 HICKS Mcghp Chap_05 Pgs 209 7/10/2001
CONCRETE FORMULAS
a f m
s h
e l
209
FIGURE 5.5 Cantilever retaining wall. (a) Vertical section shows main reinforcing steel placed vertically in the stem. (b) Moment diagram.
base (Fig. 5.5). Cantilever walls generally are economical for heights from 10 to 20 ft (3 to 6 m). For lower walls, gravity walls may be less costly; for taller walls, counterforts (Fig. 5.6) may be less expensive. Shear unit stress on a horizontal section of a counterfort may be computed from vc V1/bd, where b is the thickness of the counterfort and d is the horizontal distance from face of wall to main steel, V1 V
M (tan tan ) d TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 210
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 210
210
CHAPTER FIVE
w
F T a i
W T w w F f u o m m
w FIGURE 5.6 Counterfort retaining wall. (a) Vertical section. (b) Horizontal section.
TLFeBOOK
40816_05b_p196-212 s 210
10/22/01
12:46 PM
Page 211
40816 HICKS Mcghp Chap_05 Pgs 211 7/10/2001
CONCRETE FORMULAS
211
where V shear on section M bending moment at section angle earth face of counterfort makes with vertical angle wall face makes with vertical For a vertical wall face, 0 and V1 V (M/d)tan . The critical section for shear may be taken conservatively at a distance up from the base equal to d sin cos , where d is the depth of counterfort along the top of the base.
WALL FOOTINGS The spread footing under a wall (Fig. 5.7) distributes the wall load horizontally to preclude excessive settlement. The footing acts as a cantilever on opposite sides of the wall under downward wall loads and upward soil pressure. For footings supporting concrete walls, the critical section for bending moment is at the face of the wall; for footings under masonry walls, halfway between the middle and edge of the wall. Hence, for a 1-ft (0.305-m) long strip of symmetrical concrete-wall footing, symmetrically loaded, the maximum moment, ftlb (Nm), is M
p (L a)2 8
where p uniform pressure on soil, lb/ft2 (Pa) L width of footing, ft (m) a wall thickness, ft (m) TLFeBOOK
40816_05b_p196-212
10/22/01
12:46 PM
Page 212
40816 HICKS Mcghp Ch05 Third Pass bcj 7/19/01 Pgs 212
212
CHAPTER FIVE
FIGURE 5.7 Concrete wall footing.
If the footing is sufficiently deep that the tensile bending stress at the bottom, 6M/t2, where M is the factored moment and t is the footing depth, in (mm), does not exceed 5√f c , where fc is the 28-day concrete strength, lb/in2 (MPa) and 0.90, the footing does not need to be reinforced. If the tensile stress is larger, the footing should be designed as a 12-in (305-mm) wide rectangular, reinforced beam. Bars should be placed across the width of the footing, 3 in (76.2 mm) from the bottom. Bar development length is measured from the point at which the critical section for moment occurs. Wall footings also may be designed by ultimatestrength theory.
TLFeBOOK
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
12:47 PM
Chap_06
Page 213
Pgs 214 – 242
7/10/2001
CHAPTER 6
TIMBER ENGINEERING FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
214
12:47 PM
Chap_06
Page 214
Pgs 214 – 242
7/10/2001
CHAPTER SIX
GRADING OF LUMBER Stress-grade lumber consists of three classifications: 1. Beams and stringers. Lumber of rectangular cross section, 5 in (127 mm) or more thick and 8 in (203 mm) or more wide, graded with respect to its strength in bending when loaded on the narrow face. 2. Joists and planks. Lumber of rectangular cross section, 2 in (50.8 mm) to, but not including, 5 in (127 mm) thick and 4 in (102 mm) or more wide, graded with respect to its strength in bending when loaded either on the narrow face as a joist or on the wide face as a plank. 3. Posts and timbers. Lumber of square, or approximately square, cross section 5 5 in (127 by 127 mm), or larger, graded primarily for use as posts or columns carrying longitudinal load, but adapted for miscellaneous uses in which the strength in bending is not especially important. Allowable unit stresses apply only for loading for which lumber is graded.
SIZE OF LUMBER Lumber is usually designated by a nominal size. The size of unfinished lumber is the same as the nominal size, but the dimensions of dressed or finished lumber are from 38 to 12 in (9.5 to 12.7 mm) smaller. Properties of a few selected standard lumber sizes, along with the formulas for these properties, are shown in Table 6.1. TLFeBOOK
r -
, ) t -
y , g n .
h
f e n d ,
HICKS
6.45 22.53
3.56 8.19
158 712
12.19
57.13
15.23
5
1
3
2
1 113
National Lumber Manufacturers Association.
TLFeBOOK
Page 215
1 8 5 2
5.89 8.93
158 358
Board feet per linear foot of piece
12:47 PM
Section modulus bh 2 S 6
7/10/2001
Source:
Moment of inertia bh 2 I 12
Pgs 214 – 242
24 26 28
Area of section A bh 2
Standard dressed size S4S b h
Chap_06
215 Nominal size b h
10/22/01
Mcghp
(Dressed (S4S) sizes, moment of inertia, and section modulus are given with respect to xx axis, with dimensions b and h, as shown on sketch)
40816_06_p213-242
40816
TABLE 6.1 Properties of Sections for Standard Lumber Sizes.
40816_06_p213-242 40816
HICKS
216
10/22/01 Mcghp
12:47 PM
Chap_06
Page 216
Pgs 214 – 242
7/10/2001
CHAPTER SIX
BEARING The allowable unit stresses given for compression perpendicular to the grain apply to bearings of any length at the ends of beams and to all bearings 6 in (152.4 mm) or more in length at other locations. When calculating the required bearing area at the ends of beams, no allowance should be made for the fact that, as the beam bends, the pressure upon the inner edge of the bearing is greater than at the end of the beam. For bearings of less than 6 in (152.4 mm) in length and not nearer than 3 in (76.2 mm) to the end of the member, the allowable stress for compression perpendicular to the grain should be modified by multiplying by the factor (l 38)/l, where l is the length of the bearing in inches (mm) measured along the grain of the wood.
A n f
BEAMS The extreme fiber stress in bending for a rectangular timber beam is f 6M/bh2 M/S A beam of circular cross section is assumed to have the same strength in bending as a square beam having the same cross-sectional area. The horizontal shearing stress in a rectangular timber beam is H 3V/2bh (6.1) For a rectangular timber beam with a notch in the lower face at the end, the horizontal shearing stress is TLFeBOOK
f o s o
40816_06_p213-242 40816
s n d e n f n e r r s
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 217
Pgs 214 – 242
7/10/2001
TIMBER ENGINEERING FORMULAS
217
H (3V/2bd1) (h /d1)
(6.2)
A gradual change in cross section, instead of a square notch, decreases the shearing stress nearly to that computed for the actual depth above the notch. Nomenclature for the preceding equations follows: f maximum fiber stress, lb/in2 (MPa) M bending moment, lbin (Nm) h depth of beam, in (mm) b width of beam, in (mm) S section modulus (bh2/6 for rectangular section), in3 (mm3) H horizontal shearing stress, lb/in2 (MPa) V total shear, lb (N) d1 depth of beam above notch, in (mm)
r
l span of beam, in (mm) P concentrated load, lb (N) V1 modified total end shear, lb (N)
e e r ) r
W total uniformly distributed load, lb (N) x distance from reaction to concentrated load in (mm) For simple beams, the span should be taken as the distance from face to face of supports plus one-half the required length of bearing at each end; and for continuous beams, the span should be taken as the distance between the centers of bearing on supports. TLFeBOOK
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
218
12:47 PM
Chap_06
Page 218
Pgs 214 – 242
7/10/2001
CHAPTER SIX
When determining V, neglect all loads within a distance from either support equal to the depth of the beam. In the stress grade of solid-sawn beams, allowances for checks, end splits, and shakes have been made in the assigned unit stresses. For such members, Eq. (6.1) does not indicate the actual shear resistance because of the redistribution of shear stress that occurs in checked beams. For a solid-sawn beam that does not qualify using Eq. (6.1) and the H values given in published data for allowable unit stresses, the modified reaction V1 should be determined as shown next.
f
b
For concentrated loads, V1
10P(l x) (x /h)2 9l[2 (x /h)2]
(6.3) T c V m
For uniform loading, V1
W 2
1 2hl
(6.4)
The sum of the V 1 values from Eqs. (6.3) and (6.4) should be substituted for V in Eq. (6.1), and the resulting H values should be checked against those given in tables of allowable unit stresses for end-grain bearing. Such values should be adjusted for duration of loading.
COLUMNS The allowable unit stress on timber columns consisting of a single piece of lumber or a group of pieces glued together to form a single member is TLFeBOOK
s i
40816_06_p213-242 40816
e r d e f n s d
)
) d s d
f r
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 219
Pgs 214 – 242
7/10/2001
TIMBER ENGINEERING FORMULAS
219
3.619E P A (l/r)2
(6.5)
For columns of square or rectangular cross section, this formula becomes 0.30E P A (l/d)2
(6.6)
For columns of circular cross section, the formula becomes P 0.22E A (l/d)2
(6.7)
The allowable unit stress, P/A, may not exceed the allowable compressive stress, c. The ratio, 1/d, must not exceed 50. Values of P/A are subject to the duration of loading adjustment given previously. Nomenclature for Eqs. (6.5) to (6.7) follows: P total allowable load, lb (N) A area of column cross section, in2 (mm2) c allowable unit stress in compression parallel to grain, lb/in2 (MPa) d dimension of least side of column, in (mm) l unsupported length of column between points of lateral support, in (mm) E modulus of elasticity, lb/in2 (MPa) r least radius of gyration of column, in (mm) For members loaded as columns, the allowable unit stresses for bearing on end grain (parallel to grain) are given in data published by lumber associations. These allowable TLFeBOOK
40816_06_p213-242 40816
220
HICKS
10/22/01 Mcghp
12:47 PM
Chap_06
Page 220
Pgs 214 – 242
7/10/2001
CHAPTER SIX
stresses apply provided there is adequate lateral support and end cuts are accurately squared and parallel. When stresses exceed 75 percent of values given, bearing must be on a snug-fitting metal plate. These stresses apply under conditions continuously dry, and must be reduced by 27 percent for glued-laminated lumber and lumber 4 in (102 mm) or less in thickness and by 9 percent for sawn lumber more than 4 in (102 mm) in thickness, for lumber exposed to weather.
w
COMBINED BENDING AND AXIAL LOAD Members under combined bending and axial load should be so proportioned that the quantity Pa /P M a /M 1
(6.8)
where Pa total axial load on member, lb (N) P total allowable axial load, lb (N) Ma total bending moment on member, lb in (Nm)
R F T w L m e
M total allowable bending moment, lb in (Nm)
T a
COMPRESSION AT ANGLE TO GRAIN The allowable unit compressive stress when the load is at an angle to the grain is c c (c)/[c (sin )2 (c) (cos )2]
(6.9) TLFeBOOK
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 221
Pgs 214 – 242
TIMBER ENGINEERING FORMULAS
d s a s r s n
7/10/2001
221
where c allowable unit stress at angle to grain, lb/in2 (MPa) c allowable unit stress parallel to grain, lb/in2 (MPa) c allowable unit stress perpendicular to grain, lb/in2 (MPa) angle between direction of load and direction of grain
e
RECOMMENDATIONS OF THE FOREST PRODUCTS LABORATORY
)
The Wood Handbook gives advice on the design of solid wood columns. (Wood Handbook, USDA Forest Products Laboratory, Madison, Wisc., 1999.) Columns are divided into three categories, short, intermediate, and long. Let K denote a parameter defined by the equation
) )
K 0.64
Ef
1/2
(6.10)
c
The range of the slenderness ratio and the allowable stress assigned to each category are next. t
)
Short column, L 11 d
f fc
(6.11) TLFeBOOK
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
222
12:47 PM
Chap_06
Page 222
Pgs 214 – 242
7/10/2001
CHAPTER SIX
C
Intermediate column, 11
L K d
f fc 1
1 3
L/dK 4
(6.12)
C f t
Long column, L K d
f
0.274E (L /d )2
(6.13)
The maximum L /d ratio is set at 50. The National Design Specification covers the design of solid columns. The allowable stress in a rectangular section is as follows: f
0.30E (L /d)2
but
f fc
(6.14)
The notational system for the preceding equations is P A L d E fc
allowable load sectional area unbraced length smaller dimension of rectangular section modulus of elasticity allowable compressive stress parallel to grain in short column of given species f allowable compressive stress parallel to grain in given column TLFeBOOK
a m a t f
I
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 223
Pgs 214 – 242
TIMBER ENGINEERING FORMULAS
7/10/2001
223
COMPRESSION ON OBLIQUE PLANE )
)
f n
Consider that a timber member sustains a compressive force with an action line that makes an oblique angle with the grain. Let P Q N
allowable compressive stress parallel to grain allowable compressive stress normal to grain allowable compressive stress inclined to grain angle between direction of stress N and direction of grain
By Hankinson’s equation, N
)
PQ P sin 2 Q cos2
(6.15)
In Fig. 6.1, member M1 must be notched at the joint to avoid removing an excessive area from member M2. If the member is cut in such a manner that AC and BC make an angle of /2 with vertical and horizontal planes, respectively, the allowable bearing pressures at these faces are identical for the two members. Let A sectional area of member M1 f1 pressure at AC f2 pressure at BC It may be readily shown that AC b
sin ( /2) sin
BC b
cos ( /2) sin
(6.16) TLFeBOOK
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
224
12:47 PM
Chap_06
Page 224
Pgs 214 – 242
7/10/2001
CHAPTER SIX
w
FIGURE 6.1 Timber joint.
f1
F sin A tan (/2)
f2
F sin tan ( /2) A
(6.17)
This type of joint is often used in wood trusses.
ADJUSTMENT FACTORS FOR DESIGN VALUES Design values obtained by the methods described earlier should be multiplied by adjustment factors based on conditions of use, geometry, and stability. The adjustments are cumulative, unless specifically indicated in the following: The adjusted design value Fb for extreme-fiber bending is given by TLFeBOOK
F i
w
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 225
Pgs 214 – 242
7/10/2001
TIMBER ENGINEERING FORMULAS
Fb FbCDCMCtCLCF CV CfuCrCcCf
225 (6.18)
where Fb design value for extreme-fiber bending CD load-duration factor CM wet-service factor Ct temperature factor CL beam stability factor CF size factor—applicable only to visually graded, sawn lumber and round timber flexural members C v volume factor—applicable only to gluedlaminated beams Cfu flat-use factor—applicable only to dimensionlumber beams 2 to 4 in (50.8 to 101.6 mm) thick and glued-laminated beams )
Cr repetitive-member factor—applicable only to dimension-lumber beams 2 to 4 in (50.8 to 101.6 mm) thick Cc curvature factor—applicable only to curved portions of glued-laminated beams Cf form factor
d f g
For glued-laminated beams, use either CL or Cv (whichever is smaller), not both. The adjusted design value for tension Ft is given by Ft FtCDCMCtCF
(6.19)
where Ft is the design value for tension. TLFeBOOK
40816_06_p213-242 40816
226
HICKS
10/22/01 Mcghp
12:47 PM
Chap_06
Page 226
Pgs 214 – 242
7/10/2001
CHAPTER SIX
For shear, the adjusted design value Fv is computed from FV FVCDCMCtCH
w
(6.20)
where Fv is the design value for shear and CH is the shear stress factor ≥1—permitted for Fv parallel to the grain for sawn lumber members. For compression perpendicular to the grain, the adjusted design value Fc is obtained from Fc FcCMCtCb
(6.21)
where Fc is the design value for compression perpendicular to the grain and Cb is the bearing area factor. For compression parallel to the grain, the adjusted design value Fc is given by Fc FcCDCMCtCFCp
(6.22)
where Fc is the design value for compression parallel to grain and Cp is the column stability factor. For end grain in bearing parallel to the grain, the adjusted design value, Fg is computed from Fg FgCDCt
(6.23)
where Fg is the design value for end grain in bearing parallel to the grain. The adjusted design value for modulus of elasticity, E is obtained from E ECMCT C
(6.24) TLFeBOOK
S F a s f o s a a g r o e b
D s
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 227
Pgs 214 – 242
7/10/2001
227
TIMBER ENGINEERING FORMULAS
m ) r r d
) n
) o d
) s
)
where E design value for modulus of elasticity CT buckling stiffness factor—applicable only to sawn-lumber truss compression chords 2 4 in (50.8 101.6 mm) or smaller, when subject to combined bending and axial compression and plywood sheathing 38 in (9.5 mm) or more thick is nailed to the narrow face C other appropriate adjustment factors Size and Volume Factors For visually graded dimension lumber, design values Fb, Ft , and Fc for all species and species combinations, except southern pine, should be multiplied by the appropriate size factor Cf , given in reference data to account for the effects of member size. This factor and the factors used to develop size-specific values for southern pine are based on the adjustment equation given in American Society for Testing and Materials (ASTM) D1990. This equation, based on ingrade test data, accounts for differences in Fb, Ft, and Fc related to width and in Fb and Ft related to length (test span). For visually graded timbers [5 5 in (127 127 mm) or larger], when the depth d of a stringer beam, post, or timber exceeds 12 in (304.8 mm), the design value for bending should be adjusted by the size factor CF (12 /d)1/9
(6.25)
Design values for bending Fb for glued-laminated beams should be adjusted for the effects of volume by multiplying by CV K L
21L 12d 5.125 b
1/x
(6.25) TLFeBOOK
40816_06_p213-242 40816
228
HICKS
10/22/01 Mcghp
12:47 PM
Chap_06
Page 228
Pgs 214 – 242
7/10/2001
CHAPTER SIX
where L length of beam between inflection points, ft (m) d depth, in (mm), of beam b width, in (mm), of beam width, in (mm), of widest piece in multiple-piece layups with various widths; thus, b ≤ 10.75 in (273 mm) x 20 for southern pine 10 for other species KL loading condition coefficient For glulam beams, the smaller of Cv and the beam stability factor CL should be used, not both.
( F g z f T f fi m s ( F p w t
Radial Stresses and Curvature Factor The radial stress induced by a bending moment in a member of constant cross section may be computed from
fr
3M 2Rbd
(6.26)
where M bending moment, inlb (Nm) R radius of curvature at centerline of member, in (mm) b width of cross section, in (mm)
w r s 1
f o
B D F a
d depth of cross section, in (mm) TLFeBOOK
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 229
Pgs 214 – 242
TIMBER ENGINEERING FORMULAS
)
e n
y
-
,
229
When M is in the direction tending to decrease curvature (increase the radius), tensile stresses occur across the grain. For this condition, the allowable tensile stress across the grain is limited to one-third the allowable unit stress in horizontal shear for southern pine for all load conditions and for Douglas fir and larch for wind or earthquake loadings. The limit is 15 lb/in2 (0.103 MPa) for Douglas fir and larch for other types of loading. These values are subject to modification for duration of load. If these values are exceeded, mechanical reinforcement sufficient to resist all radial tensile stresses is required. When M is in the direction tending to increase curvature (decrease the radius), the stress is compressive across the grain. For this condition, the design value is limited to that for compression perpendicular to grain for all species. For the curved portion of members, the design value for wood in bending should be modified by multiplication by the following curvature factor: Cc 1 2000
)
7/10/2001
Rt
2
(6.27)
where t is the thickness of lamination, in (mm), and R is the radius of curvature of lamination, in (mm). Note that t/R should not exceed 1100 for hardwoods and southern pine or 1 125 for softwoods other than southern pine. The curvature factor should not be applied to stress in the straight portion of an assembly, regardless of curvature elsewhere.
Bearing Area Factor Design values for compression perpendicular to the grain Fc apply to bearing surfaces of any length at the ends of a member and to all bearings 6 in (152.4 mm) or more long TLFeBOOK
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
230
12:47 PM
Chap_06
Page 230
Pgs 214 – 242
7/10/2001
CHAPTER SIX
at other locations. For bearings less than 6 in (152.4 mm) long and at least 3 in (76.2 mm) from the end of a member, Fc may be multiplied by the bearing area factor: Cb
L b 0.375 Lb
(6.28)
where Lb is the bearing length, in (mm) measured parallel to grain. Equation (6.28) yields the values of Cb for elements with small areas, such as plates and washers, listed in reference data. For round bearing areas, such as washers, Lb should be taken as the diameter.
(6.29)
s p t t l p m b c 9
design value for compression parallel to the grain multiplied by all applicable adjustment factors except Cp
w
Column Stability and Buckling Stiffness Factors Design values for compression parallel to the grain Ft should be multiplied by the column stability factor Cp given by Eq. (6.29): CP
1 (FcE /F c*) 2c
where
F *c
F o
√
1
(FcE /F c*) 2c
2
(FcE /Fc* ) c
2 FcE K cE E/(L e /d)
E modulus of elasticity multiplied by adjust-
ment factors
TLFeBOOK
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 231
Pgs 214 – 242
TIMBER ENGINEERING FORMULAS
) ,
)
7/10/2001
231
KcE 0.3 for visually graded lumber and machineevaluated lumber 0.418 for products with a coefficient of variation less than 0.11 c 0.80 for solid-sawn lumber
l s b
Ft n
)
0.85 for round timber piles 0.90 for glued-laminated timber For a compression member braced in all directions throughout its length to prevent lateral displacement, Cp 1.0. The buckling stiffness of a truss compression chord of sawn lumber subjected to combined flexure and axial compression under dry service conditions may be increased if the chord is 2 4 in (50.8 101.6 mm) or smaller and has the narrow face braced by nailing to plywood sheathing at least 38 in (9.5 mm) thick in accordance with good nailing practice. The increased stiffness may be accounted for by multiplying the design value of the modulus of elasticity E by the buckling stiffness factor CT in column stability calculations. When the effective column length Le, in (mm), is 96 in (2.38 m) or less, CT may be computed from CT 1
e t
KM Le KT E
(6.30)
where KM 2300 for wood seasoned to a moisture content of 19 percent or less at time of sheathing attachment 1200 for unseasoned or partly seasoned wood at time of sheathing attachment TLFeBOOK
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
232
12:47 PM
Chap_06
Page 232
Pgs 214 – 242
7/10/2001
CHAPTER SIX
KT 0.59 for visually graded lumber and machineevaluated lumber
w
0.82 for products with a coefficient of variation of 0.11 or less When Le is more than 96 in (2.38 m), CT should be calculated from Eq. (6.30) with Le 96 in (2.38 m). For additional information on wood trusses with metal-plate connections, see design standards of the Truss Plate Institute, Madison, Wisconsin. The slenderness ratio RB for beams is defined by RB
√
Le d b2
(6.31)
The slenderness ratio should not exceed 50. The effective length Le for Eq. (6.31) is given in terms of unsupported length of beam in reference data. Unsupported length is the distance between supports or the length of a cantilever when the beam is laterally braced at the supports to prevent rotation and adequate bracing is not installed elsewhere in the span. When both rotational and lateral displacements are also prevented at intermediate points, the unsupported length may be taken as the distance between points of lateral support. If the compression edge is supported throughout the length of the beam and adequate bracing is installed at the supports, the unsupported length is zero. The beam stability factor CL may be calculated from CL
1 (FbE /F b*) 1.9
√
1
(FbE /F b*) 1.9
F N T e ( w
w (6.32)
2
FbE /F b* 0.95 TLFeBOOK
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 233
Pgs 214 – 242
TIMBER ENGINEERING FORMULAS
-
7/10/2001
233
where F b* design value for bending multiplied by all applicable adjustment factors, except Cfu, CV, and CL 2 FbE K bE E/R B
d l , ,
K bE 0.438 for visually graded lumber and machineevaluated lumber 0.609 for products with a coefficient of variation of 0.11 or less E design modulus of elasticity multiplied by applicable adjustment factors
)
f d a s d e n d s
FASTENERS FOR WOOD Nails and Spikes The allowable withdrawal load per inch (25.4 mm) of penetration of a common nail or spike driven into side grain (perpendicular to fibers) of seasoned wood, or unseasoned wood that remains wet, is p 1,380G5/2D
)
(6.33)
where p allowable load per inch (mm) of penetration into member receiving point, lb (N) D diameter of nail or spike, in (mm) G specific gravity of wood, oven dry TLFeBOOK
40816_06_p213-242 40816
HICKS
234
10/22/01 Mcghp
12:47 PM
Chap_06
Page 234
Pgs 214 – 242
7/10/2001
CHAPTER SIX
The total allowable lateral load for a nail or spike driven into side grain of seasoned wood is p CD 3/2
w (6.34)
where p allowable load per nail or spike, lb (N) D diameter of nail or spike, in (mm) C coefficient dependent on group number of wood (see Table 6.1) Values of C for the four groups into which stress-grade lumber is classified are Group I: C 2,040 Group II: C 1,650 Group III: C 1,350 Group IV: C 1,080
W g i
w
The loads apply where the nail or spike penetrates into the member, receiving its point at least 10 diameters for Group I species, 11 diameters for Group II species, 13 diameters for Group III species, and 14 diameters for Group IV species. Allowable loads for lesser penetrations are directly proportional to the penetration, but the penetration must be at least one-third that specified.
Wood Screws The allowable withdrawal load per inch (mm) of penetration of the threaded portion of a wood screw into side grain of seasoned wood that remains dry is TLFeBOOK
T S
D P H H P R S
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 235
Pgs 214 – 242
7/10/2001
235
TIMBER ENGINEERING FORMULAS
n
p 2,850G2D
)
where p allowable load per inch (mm) of penetration of threaded portion into member receiving point, lb (N)
(6.35)
D diameter of wood screw, in (mm) G specific gravity of wood, oven dry (see Table 6.1)
e
Wood screws should not be loaded in withdrawal from end grain. The total allowable lateral load for wood screws driven into the side grain of seasoned wood which remains dry is p CD2
(6.36)
where p allowable load per wood screw, lb (N) D diameter of wood screw, in (mm) e I r . t
n
C coefficient dependent on group number of wood (Table 6.2) TABLE 6.2 Specific Gravity and Group Number for Common Species of Lumber
Species
Group number
Specific gravity, G
G2
G5/2
Douglas fir Pine, southern Hemlock, western Hemlock, eastern Pine, Norway Redwood Spruce
II II III IV III III IV
0.51 0.59 0.44 0.43 0.47 0.42 0.41
0.260 0.348 0.194 0.185 0.221 0.176 0.168
0.186 0.267 0.128 0.121 0.151 0.114 0.108 TLFeBOOK
40816_06_p213-242 40816
HICKS
236
10/22/01 Mcghp
12:47 PM
Chap_06
Page 236
Pgs 214 – 242
7/10/2001
CHAPTER SIX
Values of C for the four groups into which stress-grade lumber is classified are Group I: C 4,800 Group II: C 3,960 Group III: C 3,240 Group IV: C 2,520
w
The allowable lateral load for wood screws driven into end grain is two-thirds that given for side grain.
ADJUSTMENT OF DESIGN VALUES FOR CONNECTIONS WITH FASTENERS Nominal design values for connections or wood members with fasteners should be multiplied by applicable adjustment factors available from lumber associations and in civil engineering handbooks to obtain adjusted design values. The types of loading on the fasteners may be divided into four classes: lateral loading, withdrawal, loading parallel to grain, and loading perpendicular to grain. Adjusted design values are given in terms of nominal design values and adjustment factors in the equations below. The following variables are used in the equations: Z Z W W P P
adjusted design value for lateral loading nominal design value for lateral loading adjusted design value for withdrawal nominal design value for withdrawal adjusted value for loading parallel to grain nominal value for loading parallel to grain
w m
w TLFeBOOK
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 237
Pgs 214 – 242
7/10/2001
TIMBER ENGINEERING FORMULAS
e
237
Q adjusted value for loading normal to grain Q nominal value for loading normal to grain For bolts, Z ZCDCMCtCgD
d
where CD load-duration factor, not to exceed 1.6 for connections CM wet-service factor, not applicable to toenails loaded in withdrawal Ct temperature factor Cg group-action factor
s l . o o n d g
C geometry factor For split-ring and shear-plate connectors, P PCDCMCt CgC Cd Cst Q QCDCMCtCgC Cd where Cd is the penetration-depth factor and Cst is the metal-side-plate factor. For nails and spikes, W WCD CM Ct Ctn Z ZCD CM Ct Cd Ceg Cdi Ctn where Cdi is the diaphragm factor and Ctn toenail factor. TLFeBOOK
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
238
12:47 PM
Chap_06
Page 238
Pgs 214 – 242
7/10/2001
CHAPTER SIX
For wood screws,
t a (
W WCDCMCt Z ZCD CM Ct Cd Ceg
s t
where Ceg is the end-grain factor. For lag screws, W WCD CM Ct Ceg
w
Z ZCD CM Ct CgC Cd Ceg For metal plate connectors, Z ZCD CM Ct For drift bolts and drift pins, W WCD CM Ct Ceg Z ZCD CM Ct Cg C Cd Ceg
( C L
For spike grids, Z ZCD CM Ct C
B ROOF SLOPE TO PREVENT PONDING Roof beams should have a continuous upward slope equivalent to 14 in/ft (20.8 mm/m) between a drain and the high point of a roof, in addition to minimum recommended camber to avoid ponding. When flat roofs have insufficient slope for drainage (less than 14 in/ft) (20.8 mm/m) TLFeBOOK
M s
a
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 239
Pgs 214 – 242
7/10/2001
TIMBER ENGINEERING FORMULAS
239
the stiffness of supporting members should be such that a 5-lb/ft2 (239.4 N/mm2) load causes no more than 12 -in (12.7-mm) deflection. Because of ponding, snow loads or water trapped by gravel stops, parapet walls, or ice dams magnify stresses and deflections from existing roof loads by Cp
1 1 WL3/ 4EI
where Cp factor for multiplying stresses and deflections under existing loads to determine stresses and deflections under existing loads plus ponding W weight of 1 in (25.4 mm) of water on roof area supported by beam, lb (N) L span of beam, in (mm) E modulus of elasticity of beam material, lb/in2 (MPa) I moment of inertia of beam, in4 (mm4) (Kuenzi and Bohannan, “Increases in Deflection and Stresses Caused by Ponding of Water on Roofs,” Forest Products Laboratory, Madison, Wisconsin.)
BENDING AND AXIAL TENSION
h d )
Members subjected to combined bending and axial tension should be proportioned to satisfy the interaction equations ft f b* 1 Fc Fb and TLFeBOOK
40816_06_p213-242 40816
HICKS
10/22/01 Mcghp
240
12:47 PM
Chap_06
Page 240
Pgs 214 – 242
7/10/2001
CHAPTER SIX
( fb ft ) 1 F ** b
w
where ft tensile stress due to axial tension acting alone fb bending stress due to bending moment alone Ft design value for tension multiplied by applica-
ble adjustment factors F b* design value for bending multiplied by appli-
cable adjustment factors except CL
F ** b design value for bending multiplied by applica-
ble adjustment factors except Cv
The load duration factor CD associated with the load of shortest duration in a combination of loads with differing duration may be used to calculate Ft and F b*. All applicable load combinations should be evaluated to determine the critical load combination. F
BENDING AND AXIAL COMPRESSION Members subjected to a combination of bending and axial compression (beam columns) should be proportioned to satisfy the interaction equation
Ff [1 ( f f/F c
c
2
w m
b1
c
cE1)]F b1
a
fb2 1 [1 ( fc /FcE2) ( fb1/FbE )2]Fb2 TLFeBOOK
40816_06_p213-242 40816
10/22/01
HICKS
Mcghp
12:47 PM
Chap_06
Page 241
Pgs 214 – 242
TIMBER ENGINEERING FORMULAS
7/10/2001
241
where fc compressive stress due to axial compression acting alone e e
Fc design value for compression parallel to grain
multiplied by applicable adjustment factors, including the column stability factor
-
fb1 bending stress for load applied to the narrow face of the member
-
fb2 bending stress for load applied to the wide face of the member
f g e e
Fb1 design value for bending for load applied to
the narrow face of the member multiplied by applicable adjustment factors, including the column stability factor Fb2 design value for bending for load applied to the wide face of the member multiplied by applicable adjustment factors, including the column stability factor For either uniaxial or biaxial bending, fc should not exceed FcE1
l o
K cE E (L e1/d 1)2
where E is the modulus of elasticity multiplied by adjustment factors. Also, for biaxial bending, fc should not exceed FcE2
K cE E (L e2 /d 2)2
and fb1 should not be more than FbE
K bE E R 2B TLFeBOOK
40816_06_p213-242 40816
242
HICKS
10/22/01 Mcghp
12:47 PM
Chap_06
Page 242
Pgs 214 – 242
7/10/2001
CHAPTER SIX
where d1 is the width of the wide face and d2 is the width of the narrow face. Slenderness ratio RB for beams is given earlier in this section. KbE is defined earlier in this section. The effective column lengths Le1 for buckling in the d1 direction and Le2 for buckling in the d2 direction, E, FcE1, and FcE2 should be determined as shown earlier. As for the case of combined bending and axial tension, Fc , Fb1 , and Fb2 should be adjusted for duration of load by applying CD.
TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 243
40816 HICKS Mcghp Chap_07 pgs 243 7/12/2001
CHAPTER 7
SURVEYING FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_07_p243-256
10/22/01
12:47 PM
Page 244
40816 HICKS Mcghp Chap_07 pgs 244 7/12/2001
244
CHAPTER SEVEN
UNITS OF MEASUREMENT Units of measurement used in past and present surveys are For construction work: feet, inches, fractions of inches (m, mm) For most surveys: feet, tenths, hundredths, thousandths (m, mm) For National Geodetic Survey (NGS) control surveys: meters, 0.1, 0.01, 0.001 m The most-used equivalents are 1 meter 39.37 in (exactly) 3.2808 ft 1 rod 1 pole 1 perch 1612 ft (5.029 m) 1 engineer’s chain 100 ft 100 links (30.48 m) 1 Gunter’s chain 66 ft (20.11 m) 100 Gunter’s links (lk) 4 rods 180 mi (0.020 km) 1 acre 100,000 sq (Gunter’s) links 43,560 ft2 160 rods2 10 sq (Gunter’s) chains 4046.87 m2 0.4047 ha 1 rood 34 acre (1011.5 m2) 40 rods2 (also local unit 512 to 8 yd) (5.029 to 7.315 m)
T W q b s n d v t t
1 ha 10,000 m2 107,639.10 ft2 2.471 acres 1 arpent about 0.85 acre, or length of side of 1 square arpent (varies) (about 3439.1 m2) 1 statute mi 5280 ft 1609.35 m 1 mi2 640 acres (258.94 ha) TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 245
40816 HICKS Mcghp Chap_07 pgs 245 7/12/2001
245
SURVEYING FORMULAS
1 nautical mi (U.S.) 6080.27 ft 1853.248 m e s
1 fathom 6 ft (1.829 m) 1 cubit 18 in (0.457 m)
s
1 vara 33 in (0.838 m) (Calif.), 3313 in (0.851 m) (Texas), varies
:
1 degree 1360 circle 60 min 3600 s 0.01745 rad sin 1 0.01745241 1 rad 57 17 44.8 or about 57.30 1 grad (grade) 1400 circle 1100 quadrant 100 centesimal min 104 centesimals (French) 1 mil 16400 circle 0.05625 1 military pace (milpace) 212 ft (0.762 m)
THEORY OF ERRORS When a number of surveying measurements of the same quantity have been made, they must be analyzed on the basis of probability and the theory of errors. After all systematic (cumulative) errors and mistakes have been eliminated, random (compensating) errors are investigated to determine the most probable value (mean) and other critical values. Formulas determined from statistical theory and the normal, or Gaussian, bell-shaped probability distribution curve, for the most common of these values follow. TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 246
40816 HICKS Mcghp Chap_07 pgs 246 7/12/2001
246
CHAPTER SEVEN
Standard deviation of a series of observations is s
√
d 2 n1
where d residual (difference from mean) of single observation and n number of observations. The probable error of a single observation is PE s 0.6745s (The probability that an error within this range will occur is 0.50.) The probability that an error will lie between two values is given by the ratio of the area of the probability curve included between the values to the total area. Inasmuch as the area under the entire probability curve is unity, there is a 100 percent probability that all measurements will lie within the range of the curve. The area of the curve between s is 0.683; that is, there is a 68.3 percent probability of an error between s in a single measurement. This error range is also called the one-sigma or 68.3 percent confidence level. The area of the curve between 2s is 0.955. Thus there is a 95.5 percent probability of an error between 2s and 2s that represents the 95.5 percent error (two-sigma or 95.5 percent confidence level). Similarly, 3s is referred to as the 99.7 percent error (three-sigma or 99.7 percent confidence level). For practical purposes, a maximum tolerable level often is assumed to be the 99.9 percent error. Table 7.1 indicates the probability of occurrence of larger errors in a single measurement. The probable error of the combined effects of accidental errors from different causes is TLFeBOOK
w m
w
M R d
40816_07_p243-256
10/22/01
12:47 PM
Page 247
40816 HICKS Mcghp Chap_07 pgs 247 7/12/2001
247
SURVEYING FORMULAS
TABLE 1 Probability of Error in a Single Measurement
-
Error
Confidence level, %
Probability of larger error
Probable (0.6745s) Standard deviation (s) 90% (1.6449s) 2s or 95.5% 3s or 97.7% Maximum (3.29s)
50 68.3 90 95.5 99.7 99.9
1 in 2 1 in 3 1 in 10 1 in 20 1 in 370 1 in 1000
s s e e a n ,
Esum √E 21 E22 E23 where E1, E2, E3 . . . are probable errors of the separate measurements. Error of the mean is Em
s
e e t s 7 . n s e l
Esum E √n E s s n n √n
where Es specified error of a single measurement. Probable error of the mean is PEm
PEs 0.6745 √n
√
d 2 n(n 1)
MEASUREMENT OF DISTANCE WITH TAPES Reasonable precisions for different methods of measuring distances are TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 248
40816 HICKS Mcghp Chap_07 pgs 248 7/12/2001
248
CHAPTER SEVEN
Pacing (ordinary terrain): 150 to 1100 Taping (ordinary steel tape): 11000 to 110,000 (Results can be improved by use of tension apparatus, transit alignment, leveling.) Baseline (invar tape): 150,000 to 11,000,000 Stadia: 1300 to 1500 (with special procedures) Subtense bar: 11000 to 17000 (for short distances, with a 1-s theodolite, averaging angles taken at both ends) Electronic distance measurement (EDM) devices have been in use since the middle of the twentieth century and have now largely replaced steel tape measurements on large projects. The continued development, and the resulting drop in prices, are making their use widespread. A knowledge of steel-taping errors and corrections remains important, however, because use of earlier survey data requires a knowledge of how the measurements were made, common sources for errors, and corrections that were typically required. For ordinary taping, a tape accurate to 0.01 ft (0.00305 m) should be used. The tension of the tape should be about 15 lb (66.7 N). The temperature should be determined within 10°F (5.56°C); and the slope of the ground, within 2 percent; and the proper corrections, applied. The correction to be applied for temperature when using a steel tape is
w
f t
T
Ct 0.0000065s(T T0) w The correction to be made to measurements on a slope is Ch s (1 cos ) or
0.00015s
or
h 2 /2s
2
exact approximate approximate TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 249
40816 HICKS Mcghp Chap_07 pgs 249 7/12/2001
SURVEYING FORMULAS
249
where Ct temperature correction to measured length, ft (m) e ,
Ch correction to be subtracted from slope distance, ft (m) s measured length, ft (m)
s e d e p f s ) 5 n o
T temperature at which measurements are made, F (C) T0 temperature at which tape is standardized, F (C) h difference in elevation at ends of measured length, ft (m) slope angle, degree In more accurate taping, using a tape standardized when fully supported throughout, corrections should also be made for tension and for support conditions. The correction for tension is Cp
(Pm Ps)s SE
The correction for sag when not fully supported is Cs
w 2L3 24P m2
where Cp tension correction to measured length, ft (m) Cs sag correction to measured length for each section of unsupported tape, ft (m) Pm actual tension, lb (N) Ps tension at which tape is standardized, lb (N) (usually 10 lb) (44.4 N) TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 250
40816 HICKS Mcghp Chap_07 pgs 250 7/12/2001
250
CHAPTER SEVEN
S cross-sectional area of tape, in2 (mm2)
F
E modulus of elasticity of tape, lb/in (MPa) (29 million lb/in2 (MPa) for steel) (199,955 MPa) 2
w weight of tape, lb/ft (kg/m) w E (
L unsupported length, ft (m) Slope Corrections In slope measurements, the horizontal distance H L cos x, where L slope distance and x vertical angle, measured from the horizontal—a simple hand calculator operation. For slopes of 10 percent or less, the correction to be applied to L for a difference d in elevation between tape ends, or for a horizontal offset d between tape ends, may be computed from Cs
d2 2L
For a slope greater than 10 percent, Cs may be determined from Cs
d2 d4 2L 8L3
O T t a
Temperature Corrections
f b
For incorrect tape length: Ct
w
(actual tape length nominal tape length)L nominal tape length TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 251
40816 HICKS Mcghp Chap_07 pgs 251 7/12/2001
SURVEYING FORMULAS
251
For nonstandard tension: ) )
Ct
(applied pull standard tension)L AE
where A cross-sectional area of tape, in2 (mm2); and E modulus of elasticity 29,000,00 lb/in2 for steel (199,955 MPa). For sag correction between points of support, ft (m): L , r o e e
C
w2 L3s 24P2
where w weight of tape per foot, lb (N) Ls unsupported length of tape, ft (m) P pull on tape, lb (N)
m
Orthometric Correction This is a correction applied to preliminary elevations due to flattening of the earth in the polar direction. Its value is a function of the latitude and elevation of the level circuit. Curvature of the earth causes a horizontal line to depart from a level surface. The departure Cf , ft, or Cm, (m), may be computed from Cf 0.667M 2 0.0239F 2 Cm 0.0785K 2 TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 252
40816 HICKS Mcghp Chap_07 pgs 252 7/12/2001
252
CHAPTER SEVEN
where M, F, and K are distances in miles, thousands of feet, and kilometers, respectively, from the point of tangency to the earth. Refraction causes light rays that pass through the earth’s atmosphere to bend toward the earth’s surface. For horizontal sights, the average angular displacement (like the sun’s diameter) is about 32 min. The displacement Rf, ft, or Rm, m, is given approximately by R f 0.093M 2 0.0033F 2
V T N o G C d l
R m 0.011K 2 To obtain the combined effect of refraction and curvature of the earth, subtract Rf from Cf or Rm from Cm. Borrow-pit or cross-section leveling produces elevations at the corners of squares or rectangles with sides that are dependent on the area to be covered, type of terrain, and accuracy desired. For example, sides may be 10, 20, 40, 50, or 100 ft (3.048, 6.09, 12.19, 15.24, or 30.48 m). Contours can be located readily, but topographic features, not so well. Quantities of material to be excavated or filled are computed, in yd3 (m3), by selecting a grade elevation or final ground elevation, computing elevation differences for the corners, and substituting in Q
nxA 108
where n number of times a particular corner enters as part of a division block x difference in ground and grade elevation for each corner, ft (m) A area of each block, ft2 (m2) TLFeBOOK
w
S I c i c b b f
40816_07_p243-256
10/22/01
12:47 PM
Page 253
40816 HICKS Mcghp Chap_07 pgs 253 7/12/2001
SURVEYING FORMULAS
, o s s ,
f s e d , s . l e
s r
253
VERTICAL CONTROL The NGS provides vertical control for all types of surveys. NGS furnishes descriptions and elevations of bench marks on request. As given in “Standards and Specifications for Geodetic Control Networks,” Federal Geodetic Control Committee, the relative accuracy C, mm, required between directly connected bench marks for the three orders of leveling is First order: C 0.5√K for Class I and 0.7√K for Class II Second order: C 1.0√K for Class I and 1.3√K for Class II Third order: C 2.0√K where K is the distance between bench marks, km.
STADIA SURVEYING In stadia surveying, a transit having horizontal stadia crosshairs above and below the central horizontal crosshair is used. The difference in the rod readings at the stadia crosshairs is termed the rod intercept. The intercept may be converted to the horizontal and vertical distances between the instrument and the rod by the following formulas: H Ki(cos a)2 ( f c) cos a V
1 Ki(sin 2a) ( f c) sin a 2 TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 254
40816 HICKS Mcghp Chap_07 pgs 254 7/12/2001
254
CHAPTER SEVEN
where H horizontal distance between center of transit and rod, ft (m) V vertical distance between center of transit and point on rod intersected by middle horizontal crosshair, ft (m) K stadia factor (usually 100) i rod intercept, ft (m) a vertical inclination of line of sight, measured from the horizontal, degree f c instrument constant, ft (m) (usually taken as 1 ft) (0.3048 m) In the use of these formulas, distances are usually calculated to the foot (meter) and differences in elevation to tenths of a foot (meter). Figure 7.1 shows stadia relationships for a horizontal sight with the older type of external-focusing telescope. Relationships are comparable for the internal-focusing type. For horizontal sights, the stadia distance, ft, (m) (from instrument spindle to rod), is DR
f C i
where R intercept on rod between two sighting wires, ft (m) f focal length of telescope, ft (m) (constant for specific instrument) i distance between stadia wires, ft (m) TLFeBOOK
F t h
C f T o
P P m q i s
40816_07_p243-256
10/22/01
12:47 PM
Page 255
40816 HICKS Mcghp Chap_07 pgs 255 7/12/2001
SURVEYING FORMULAS
255
t d l
d s d a l . . m
, r
FIGURE 7.1 Distance D is measured with an external-focusing telescope by determining interval R intercepted on a rod AB by two horizontal sighting wires a and b.
Cfc c distance from center of spindle to center of objective lens, ft (m) C is called the stadia constant, although c and C vary slightly. The value of f/i, the stadia factor, is set by the manufacturer to be about 100, but it is not necessarily 100.00. The value should be checked before use on important work, or when the wires or reticle are damaged and replaced.
PHOTOGRAMMETRY Photogrammetry is the art and science of obtaining reliable measurements by photography (metric photogrammetry) and qualitative evaluation of image data (photo interpretation). It includes use of terrestrial, close-range, aerial, vertical, oblique, strip, and space photographs along with their interpretation. TLFeBOOK
40816_07_p243-256
10/22/01
12:47 PM
Page 256
40816 HICKS Mcghp Chap_07 pgs 256 7/12/2001
256
CHAPTER SEVEN
Scale formulas are as follows: Photo scale photo distance Map scale map distance Photo scale
f ab AB H h1
where f focal length of lens, in (m) H flying height of airplane above datum (usually mean sea level), ft (m) h1 elevation of point, line, or area with respect to datum, ft (m)
TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 257
40816 HICKS Mcghp Chap_8 Pgs 257 7/12/2001
CHAPTER 8
SOIL AND EARTHWORK FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_08_p257-282
10/22/01
12:48 PM
Page 258
40816 HICKS Mcghp Chap_8 Pgs 258 7/12/2001
258
CHAPTER EIGHT
PHYSICAL PROPERTIES OF SOILS Basic soil properties and parameters can be subdivided into physical, index, and engineering categories. Physical soil properties include density, particle size and distribution, specific gravity, and water content. The water content w of a soil sample represents the weight of free water contained in the sample expressed as a percentage of its dry weight. The degree of saturation S of the sample is the ratio, expressed as percentage, of the volume of free water contained in a sample to its total volume of voids Vv. Porosity n, which is a measure of the relative amount of voids, is the ratio of void volume to the total volume V of soil: n
Vv V
(8.1)
The ratio of Vv to the volume occupied by the soil particles Vs defines the void ratio e. Given e, the degree of saturation may be computed from S
wGs e
w a (
I I p a r s ( t s f c p t a i
(8.2)
where Gs represents the specific gravity of the soil particles. For most inorganic soils, Gs is usually in the range of 2.67 0.05. The dry unit weight d of a soil specimen with any degree of saturation may be calculated from d
w Gs S 1 wGs
(8.3) TLFeBOOK
D l s
40816_08_p257-282
10/22/01
12:48 PM
Page 259
40816 HICKS Mcghp Chap_8 Pgs 259 7/12/2001
SOIL AND EARTHWORK FORMULAS
o c e s , f f
) s n
where w is the unit weight of water and is usually taken as 62.4 lb/ft3 (1001 kg/m3) for freshwater and 64.0 lb/ft3 (1026.7 kg/m3) for seawater.
INDEX PARAMETERS FOR SOILS Index parameters of cohesive soils include liquid limit, plastic limit, shrinkage limit, and activity. Such parameters are useful for classifying cohesive soils and providing correlations with engineering soil properties. The liquid limit of cohesive soils represents a near-liquid state, that is, an undrained shear strength about 0.01 lb/ft2 (0.0488 kg/m2). The water content at which the soil ceases to exhibit plastic behavior is termed the plastic limit. The shrinkage limit represents the water content at which no further volume change occurs with a reduction in water content. The most useful classification and correlation parameters are the plasticity index Ip, the liquidity index Il, the shrinkage index Is, and the activity Ac. These parameters are defined in Table 8.1. Relative density Dr of cohesionless soils may be expressed in terms of void ratio e or unit dry weight d:
) . f y
)
259
Dr
emax eo emax emin
(8.4)
Dr
1/min 1/d 1/min 1/max
(8.5)
Dr provides cohesionless soil property and parameter correlations, including friction angle, permeability, compressibility, small-strain shear modulus, cyclic shear strength, and so on. TLFeBOOK
Plasticity
Ip Wl Wp
Strength, compressibility, compactibility, and so forth
Liquidity
Il
Shrinkage
Is Wp Ws
260
Activity
Wn Wp Ip
Ac
Ip
Compressibility and stress rate Shrinkage potential Swell potential, and so forth
TLFeBOOK
Page 260
Wt liquid limit; Wp plastic limit; Wn moisture content, %; Ws shrinkage limit; percent of soil finer than 0.002 mm (clay size).
†
12:48 PM
Correlation
10/22/01
Definition†
Index
40816_08_p257-282
40816 HICKS Mcghp Chap_8 Pgs 260 7/12/2001
TABLE 8.1 Soil Indices
R V
T o e
U f u a
40816_08_p257-282
10/22/01
12:48 PM
Page 261
40816 HICKS Mcghp Chap_8 Pgs 261 7/12/2001
261
SOIL AND EARTHWORK FORMULAS
RELATIONSHIP OF WEIGHTS AND VOLUMES IN SOILS The unit weight of soil varies, depending on the amount of water contained in the soil. Three unit weights are in general use: the saturated unit weight sat, the dry unit weight dry, and the buoyant unit weight b:
sat
(G e)0 (1 w)G0 1e 1e
S 100%
dry
G0 (1 e)
S 0%
(G 1)0 1e
S 100%
b
Unit weights are generally expressed in pound per cubic foot or gram per cubic centimeter. Representative values of unit weights for a soil with a specific gravity of 2.73 and a void ratio of 0.80 are
sat 122 lb/ft3 1.96 g/cm3 dry 95 lb/ft3 1.52 g/cm3 b 60 lb/ft3 0.96 g/cm3 TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 262
40816 HICKS Mcghp Chap_8 Pgs 262 7/12/2001
262
CHAPTER EIGHT
The symbols used in the three preceding equations and in Fig. 8.1 are G specific gravity of soil solids (specific gravity of quartz is 2.67; for majority of soils specific gravity ranges between 2.65 and 2.85; organic soils would have lower specific gravities) 0 unit weight of water, 62.4 lb/ft3 (1.0 g/cm3) e voids ratio, volume of voids in mass of soil divided by volume of solids in same mass; also equal to n /(1 n), where n is porosity—volume of voids in mass of soil divided by total volume of same mass S degree of saturation, volume of water in mass of soil divided by volume of voids in same mass w water content, weight of water in mass of soil divided by weight of solids in same mass; also equal to Se /G
I T
w
F i r s o n
FIGURE 8.1 Relationship of weights and volumes in soil.
TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 263
40816 HICKS Mcghp Chap_8 Pgs 263 7/12/2001
263
SOIL AND EARTHWORK FORMULAS
n
INTERNAL FRICTION AND COHESION The angle of internal friction for a soil is expressed by tan
d
where angle of internal friction tan coefficient of internal friction normal force on given plane in cohesionless soil mass shearing force on same plane when sliding on plane is impending For medium and coarse sands, the angle of internal friction is about 30° to 35°. The angle of internal friction for clays ranges from practically 0° to 20°. The cohesion of a soil is the shearing strength that the soil possesses by virtue of its intrinsic pressure. The value of the ultimate cohesive resistance of a soil is usually designated by c. Average values for c are given in Table 8.2. TABLE 8.2 Cohesive Resistance of Various Soil Types Cohesion c General soil type
lb/ft2
(kPa)
Almost-liquid clay Very soft clay Soft clay Medium clay Damp, muddy sand
100 200 400 1000 400
(4.8) (9.6) (19.1) (47.8) (19.1) TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 264
40816 HICKS Mcghp Chap_8 Pgs 264 7/12/2001
264
CHAPTER EIGHT
VERTICAL PRESSURES IN SOILS
b 2
The vertical stress in a soil caused by a vertical, concentrated surface load may be determined with a fair degree of accuracy by the use of elastic theory. Two equations are in common use, the Boussinesq and the Westergaard. The Boussinesq equation applies to an elastic, isotropic, homogeneous mass that extends infinitely in all directions from a level surface. The vertical stress at a point in the mass is z
1 rz
2 5/2
3P 2 z 2
The Westergaard equation applies to an elastic material laterally reinforced with horizontal sheets of negligible thickness and infinite rigidity, which prevent the mass from undergoing lateral strain. The vertical stress at a point in the mass, assuming a Poisson’s ratio of zero, is z
P
z 2
12
rz
2 3/2
where z vertical stress at a point, lb/ft2 (kPa) P total concentrated surface load, lb (N) z depth of point at which z acts, measured vertically downward from surface, ft (m) r horizontal distance from projection of surface load P to point at which z acts, ft (m) For values of r/z between 0 and 1, the Westergaard equation gives stresses appreciably lower than those given TLFeBOOK
L F T e r a o t c w a b
40816_08_p257-282
10/22/01
12:48 PM
Page 265
40816 HICKS Mcghp Chap_8 Pgs 265 7/12/2001
SOIL AND EARTHWORK FORMULAS
265
by the Boussinesq equation. For values of r /z greater than 2.2, both equations give stresses less than P/100z2. d f n . , s e
l e m e
e d n
LATERAL PRESSURES IN SOILS, FORCES ON RETAINING WALLS The Rankine theory of lateral earth pressures, used for estimating approximate values for lateral pressures on retaining walls, assumes that the pressure on the back of a vertical wall is the same as the pressure that would exist on a vertical plane in an infinite soil mass. Friction between the wall and the soil is neglected. The pressure on a wall consists of (1) the lateral pressure of the soil held by the wall, (2) the pressure of the water (if any) behind the wall, and (3) the lateral pressure from any surcharge on the soil behind the wall. Symbols used in this section are as follows: unit weight of soil, lb/ft3 (kg/m3) (saturated unit weight, dry unit weight, or buoyant unit weight, depending on conditions) P total thrust of soil, lb/linear ft (kg/linear m) of wall H total height of wall, ft (m) angle of internal friction of soil, degree i angle of inclination of ground surface behind wall with horizontal; also angle of inclination of line of action of total thrust P and pressures on wall with horizontal KA coefficient of active pressure TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 266
40816 HICKS Mcghp Chap_8 Pgs 266 7/12/2001
266
CHAPTER EIGHT
KP coefficient of passive pressure c cohesion, lb/ft2 (kPa)
p
LATERAL PRESSURE OF COHESIONLESS SOILS
W
For walls that retain cohesionless soils and are free to move an appreciable amount, the total thrust from the soil is w P
1 2
H 2 cos i
cos i √(cos i)2 (cos )2 cos i √(cos i)2 (cos )2
T o t t
When the surface behind the wall is level, the thrust is P 12 H 2 KA where
KA tan 45
2
2
L
The thrust is applied at a point H/3 above the bottom of the wall, and the pressure distribution is triangular, with the maximum pressure of 2P/H occurring at the bottom of the wall. For walls that retain cohesionless soils and are free to move only a slight amount, the total thrust is 1.12P, where P is as given earlier. The thrust is applied at the midpoint of the wall, and the pressure distribution is trapezoidal, with the maximum pressure of 1.4P/ H extending over the middle six-tenth of the height of the wall. TLFeBOOK
F a t
o a
40816_08_p257-282
10/22/01
12:48 PM
Page 267
40816 HICKS Mcghp Chap_8 Pgs 267 7/12/2001
267
SOIL AND EARTHWORK FORMULAS
For walls that retain cohesionless soils and are completely restrained (very rare), the total thrust from the soil is P
1 2
H 2 cos i
cos i √(cos i)2 (cos )2 cos i √(cos i)2 (cos )2
When the surface behind the wall is level, the thrust is P 12 H 2 K P
e where
KP tan 45
2
2
The thrust is applied at a point H /3 above the bottom of the wall, and the pressure distribution is triangular, with the maximum pressure of 2P / H occurring at the bottom of the wall.
LATERAL PRESSURE OF COHESIVE SOILS
e o e f h -
For walls that retain cohesive soils and are free to move a considerable amount over a long period of time, the total thrust from the soil (assuming a level surface) is P 12 H 2 KA 2cH √KA or, because highly cohesive soils generally have small angles of internal friction, P 12H 2 2cH TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 268
40816 HICKS Mcghp Chap_8 Pgs 268 7/12/2001
268
CHAPTER EIGHT
The thrust is applied at a point somewhat below H/3 from the bottom of the wall, and the pressure distribution is approximately triangular. For walls that retain cohesive soils and are free to move only a small amount or not at all, the total thrust from the soil is
p s a z
P 12 H 2K P
S
because the cohesion would be lost through plastic flow.
C A s
WATER PRESSURE The total thrust from water retained behind a wall is P 120 H 2 where H height of water above bottom of wall, ft (m); and 0 unit weight of water, lb/ft3 (62.4 lb/ft3 (1001 kg/m3) for freshwater and 64 lb/ft3 (1026.7 kg/m3) for saltwater) The thrust is applied at a point H /3 above the bottom of the wall, and the pressure distribution is triangular, with the maximum pressure of 2P/H occurring at the bottom of the wall. Regardless of the slope of the surface behind the wall, the thrust from water is always horizontal.
t s
w
LATERAL PRESSURE FROM SURCHARGE
C
The effect of a surcharge on a wall retaining a cohesionless soil or an unsaturated cohesive soil can be accounted for by applying a uniform horizontal load of magnitude KA p over the entire height of the wall, where p is the surcharge in
A
TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 269
40816 HICKS Mcghp Chap_8 Pgs 269 7/12/2001
SOIL AND EARTHWORK FORMULAS
m e e
269
pound per square foot (kilopascal). For saturated cohesive soils, the full value of the surcharge p should be considered as acting over the entire height of the wall as a uniform horizontal load. KA is defined earlier.
STABILITY OF SLOPES Cohesionless Soils A slope in a cohesionless soil without seepage of water is stable if i
d r f e e ,
With seepage of water parallel to the slope, and assuming the soil to be saturated, an infinite slope in a cohesionless soil is stable if tan i
tan b
sat
where i slope of ground surface angle of internal friction of soil b, sat unit weights, lb/ft3 (kg/m3)
Cohesive Soils s y r n
A slope in a cohesive soil is stable if H
C N TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 270
40816 HICKS Mcghp Chap_8 Pgs 270 7/12/2001
270
CHAPTER EIGHT
where H height of slope, ft (m)
w
C cohesion, lb/ft (kg/m ) 2
2
unit weight, lb/ft3 (kg/m3) N stability number, dimensionless For failure on the slope itself, without seepage water, N (cos i)2 (tan i tan ) Similarly, with seepage of water,
N (cos i)2 tan i
tan b
sat
When the slope is submerged, is the angle of internal friction of the soil and is equal to b. When the surrounding water is removed from a submerged slope in a short time (sudden drawdown), is the weighted angle of internal friction, equal to (b /sat), and is equal to sat.
c T 0 d
S BEARING CAPACITY OF SOILS The approximate ultimate bearing capacity under a long footing at the surface of a soil is given by Prandtl’s equation as qu
c tan
T a
w
1 b √Kp (Kp e tan 1) 2 dry TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 271
40816 HICKS Mcghp Chap_8 Pgs 271 7/12/2001
SOIL AND EARTHWORK FORMULAS
271
where qu ultimate bearing capacity of soil, lb/ft2 (kg/m2) c cohesion, lb/ft2 (kg/m2) angle of internal friction, degree dry unit weight of dry soil, lb/ft3 (kg/m3) b width of footing, ft (m) d depth of footing below surface, ft (m) Kp coefficient of passive pressure
tan 45
2
2
e 2.718 l t l
For footings below the surface, the ultimate bearing capacity of the soil may be modified by the factor 1 Cd/b. The coefficient C is about 2 for cohesionless soils and about 0.3 for cohesive soils. The increase in bearing capacity with depth for cohesive soils is often neglected.
SETTLEMENT UNDER FOUNDATIONS
g -
The approximate relationship between loads on foundations and settlement is
q 2d C1 1 P b
Cb
2
where q load intensity, lb/ft2 (kg/m2) P settlement, in (mm) TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 272
40816 HICKS Mcghp Chap_8 Pgs 272 7/12/2001
272
CHAPTER EIGHT
d depth of foundation below ground surface, ft (m) b width of foundation, ft (m) C1 coefficient dependent on internal friction C2 coefficient dependent on cohesion The coefficients C1 and C2 are usually determined by bearingplate loading tests.
M c
L
SOIL COMPACTION TESTS The sand-cone method is used to determine in the field the density of compacted soils in earth embankments, road fill, and structure backfill, as well as the density of natural soil deposits, aggregates, soil mixtures, or other similar materials. It is not suitable, however, for soils that are saturated, soft, or friable (crumble easily). Characteristics of the soil are computed from
O d l b m 1 o
Volume of soil, ft 3 (m3)
weight of sand filling hole, lb (kg) density of sand, lb/ft 3 (kg/m 3)
F f i
% Moisture
100(weight of moist soil weight of dry soil) weight of dry soil
Field density, lb/ft 3 (kg /m3)
weight of soil, lb (kg) volume of soil, ft 3 (m3) TLFeBOOK
w r p
40816_08_p257-282
10/22/01
12:48 PM
Page 273
40816 HICKS Mcghp Chap_8 Pgs 273 7/12/2001
SOIL AND EARTHWORK FORMULAS
)
Dry density % Compaction
-
273
field density 1 % moisture/100 100(dry density) max dry density
Maximum density is found by plotting a density–moisture curve.
Load-Bearing Test
e , l . ,
One of the earliest methods for evaluating the in situ deformability of coarse-grained soils is the small-scale load-bearing test. Data developed from these tests have been used to provide a scaling factor to express the settlement of a full-size footing from the settlement 1 of a 1-ft2 (0.0929-m2) plate. This factor /1 is given as a function of the width B of the full-size bearing plate as 1
1 2B B
2
From an elastic half-space solution, Es can be expressed from results of a plate load test in terms of the ratio of bearing pressure to plate settlement kv as Es
k v (1 2) /4 4B/(1 B)2
where represents Poisson’s ratio, usually considered to range between 0.30 and 0.40. The Es equation assumes that 1 is derived from a rigid, 1-ft (0.3048-m)-diameter circular plate and that B is the equivalent diameter of the bearing TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 274
40816 HICKS Mcghp Chap_8 Pgs 274 7/12/2001
274
CHAPTER EIGHT
area of a full-scale footing. Empirical formulations, such as the /1 equation, may be significantly in error because of the limited footing-size range used and the large scatter of the database. Furthermore, consideration is not given to variations in the characteristics and stress history of the bearing soils.
California Bearing Ratio The California bearing ratio (CBR) is often used as a measure of the quality of strength of a soil that underlies a pavement, for determining the thickness of the pavement, its base, and other layers. F CBR F0 where F force per unit area required to penetrate a soil mass with a 3-in2 (1935.6-mm2) circular piston (about 2 in (50.8 mm) in diameter) at the rate of 0.05 in/min (1.27 mm/min); and F0 force per unit area required for corresponding penetration of a standard material. Typically, the ratio is determined at 0.10-in (2.54-mm) penetration, although other penetrations sometimes are used. An excellent base course has a CBR of 100 percent. A compacted soil may have a CBR of 50 percent, whereas a weaker soil may have a CBR of 10.
g l
w o v m t f
C A i t u t a m c r u
Soil Permeability The coefficient of permeability k is a measure of the rate of flow of water through saturated soil under a given hydraulic TLFeBOOK
w
40816_08_p257-282
10/22/01
12:48 PM
Page 275
40816 HICKS Mcghp Chap_8 Pgs 275 7/12/2001
SOIL AND EARTHWORK FORMULAS
s e e g
, d
275
gradient i, cm/cm, and is defined in accordance with Darcy’s law as V kiA where V rate of flow, cm3/s, and A cross-sectional area of soil conveying flow, cm2. Coefficient k is dependent on the grain-size distribution, void ratio, and soil fabric and typically may vary from as much as 10 cm/s for gravel to less than 10 –7 for clays. For typical soil deposits, k for horizontal flow is greater than k for vertical flow, often by an order of magnitude.
COMPACTION EQUIPMENT
l n 7 ) . a
A wide variety of equipment is used to obtain compaction in the field. Sheepsfoot rollers generally are used on soils that contain high percentages of clay. Vibrating rollers are used on more granular soils. To determine maximum depth of lift, make a test fill. In the process, the most suitable equipment and pressure to be applied, lb/in2 (kPa), for ground contact also can be determined. Equipment selected should be able to produce desired compaction with four to eight passes. Desirable speed of rolling also can be determined. Average speeds, mi/h (km/h), under normal conditions are given in Table 8.3. Compaction production can be computed from yd3/h (m3/h)
f c
16WSLFE P
where W width of roller, ft (m) S roller speed, mi/h (km/h) TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 276
40816 HICKS Mcghp Chap_8 Pgs 276 7/12/2001
276
CHAPTER EIGHT
TABLE 8.3 Average Speeds of Rollers Type
mi/h
(km/h)
Grid rollers Sheepsfoot rollers Tamping rollers Pneumatic rollers
12 3 10 8
(19.3) (4.8) (16.1) (12.8)
R a H
L lift thickness, in (mm) F ratio of pay yd3 (m3) to loose yd3 (m3) E efficiency factor (allows for time losses, such as those due to turns): 0.90, excellent; 0.80, average; 0.75, poor P number of passes
w t w
w
FORMULAS FOR EARTHMOVING External forces offer rolling resistance to the motion of wheeled vehicles, such as tractors and scrapers. The engine has to supply power to overcome this resistance; the greater the resistance is, the more power needed to move a load. Rolling resistance depends on the weight on the wheels and the tire penetration into the ground: R R f W R p pW
T r
(8.6)
where R rolling resistance, lb (N)
I p 1
Rf rolling-resistance factor, lb/ton (N/tonne) TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 277
40816 HICKS Mcghp Chap_8 Pgs 277 7/12/2001
SOIL AND EARTHWORK FORMULAS
277
W weight on wheels, ton (tonne) Rp tire-penetration factor, lb/tonin (N/tonnemm) penetration p tire penetration, in (mm) Rf usually is taken as 40 lb/ton (or 2 percent lb/lb) (173 N/t) and Rp as 30 lb/tonin (1.5% lb/lbin) (3288 N/tmm). Hence, Eq. (8.6) can be written as R (2% 1.5%p) W RW h ,
(8.7)
where W weight on wheels, lb (N); and R 2% 1.5%p. Additional power is required to overcome rolling resistance on a slope. Grade resistance also is proportional to weight: G R g sW
(8.8)
where G grade resistance, lb (N) Rg grade-resistance factor 20 lb/ton (86.3 N/t) 1% lb/lb (N/N) f e r . d
Thus, the total road resistance is the algebraic sum of the rolling and grade resistances, or the total pull, lb (N), required:
)
T (R R g s)W (2% 1.5%p 1%s)W (8.9)
s percent grade, positive for uphill motion, negative for downhill
In addition, an allowance may have to be made for loss of power with altitude. If so, allow 3 percent pull loss for each 1000 ft (305 m) above 2500 ft (762 m). TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 278
40816 HICKS Mcghp Chap_8 Pgs 278 7/12/2001
278
CHAPTER EIGHT
Usable pull P depends on the weight W on the drivers: PfW
P
(8.10)
where f coefficient of traction. Earth Quantities Hauled When soils are excavated, they increase in volume, or swell, because of an increase in voids: Vb VL L
100 V 100 % swell L
(8.11)
where Vb original volume, yd3 (m3), or bank yards
a a w t b
VL loaded volume, yd3 (m3), or loose yards L load factor When soils are compacted, they decrease in volume: Vc Vb S
b l y m m u
(8.12)
where Vc compacted volume, yd3 (m3); and S shrinkage factor. Bank yards moved by a hauling unit equals weight of load, lb (kg), divided by density of the material in place, lb (kg), per bank yard (m3).
E T r
SCRAPER PRODUCTION Production is measured in terms of tons or bank cubic yards (cubic meters) of material a machine excavates and discharges, under given job conditions, in 1 h. TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 279
40816 HICKS Mcghp Chap_8 Pgs 279 7/12/2001
SOIL AND EARTHWORK FORMULAS
:
279
Production, bank yd3/h (m3/h) load, yd3 (m3) trips per hour
) Trips per hour
,
)
The load, or amount of material a machine carries, can be determined by weighing or estimating the volume. Payload estimating involves determination of the bank cubic yards (cubic meters) being carried, whereas the excavated material expands when loaded into the machine. For determination of bank cubic yards (cubic meters) from loose volume, the amount of swell or the load factor must be known. Weighing is the most accurate method of determining the actual load. This is normally done by weighing one wheel or axle at a time with portable scales, adding the wheel or axle weights, and subtracting the weight empty. To reduce error, the machine should be relatively level. Enough loads should be weighed to provide a good average:
) e , r
working time, min/h cycle time, min
Bank yd3
weight of load, lb (kg) density of material, lb/bank yd3 (kg/m3)
Equipment Required To determine the number of scrapers needed on a job, required production must first be computed: Production required, yd3 /h (m3/ h)
s -
quantity, bank yd3 (m3) working time, h TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 280
40816 HICKS Mcghp Chap_8 Pgs 280 7/12/2001
280
CHAPTER EIGHT
No. of scrapers needed
production required, yd3/h (m3/h) production per unit, yd3/h (m3/h)
No. of scrapers a pusher can load
scraper cycle time, min pusher cycle time, min
Because speeds and distances may vary on haul and return, haul and return times are estimated separately.
V v i
I k m
Variable time, min
haul distance, ft return distance, ft 88 speed, mi/ h 88 speed, mi/ h
haul distance, m return distance, m 16.7 speed, km/ h 16.7 speed, km/ h
Haul speed may be obtained from the equipment specification sheet when the drawbar pull required is known.
T
F s
w a
VIBRATION CONTROL IN BLASTING Explosive users should take steps to minimize vibration and noise from blasting and protect themselves against damage claims. Vibrations caused by blasting are propagated with a velocity V, ft/s (m/s), frequency f, Hz, and wavelength L, ft (m), related by
TLFeBOOK
F s
40816_08_p257-282
10/22/01
12:48 PM
Page 281
40816 HICKS Mcghp Chap_8 Pgs 281 7/12/2001
SOIL AND EARTHWORK FORMULAS
L
281
V f
Velocity v, in/s (mm/s), of the particles disturbed by the vibrations depends on the amplitude of the vibrations A, in (mm): v 2 fA d
If the velocity v1 at a distance D1 from the explosion is known, the velocity v2 at a distance D2 from the explosion may be estimated from v2 v1
DD 1
1.5
2
The acceleration a, in/s (mm/s ), of the particles is given by 2
2
a 4 2 f 2A -
For a charge exploded on the ground surface, the overpressure P, lb/in2 (kPa), may be computed from P 226.62
WD 1/3
1.407
where W maximum weight of explosives, lb (kg) per delay; and D distance, ft (m), from explosion to exposure. The sound pressure level, decibels, may be computed from d e a ,
dB
6.95 P 10
0.084
28
For vibration control, blasting should be controlled with the scaled-distance formula:
TLFeBOOK
40816_08_p257-282
10/22/01
12:48 PM
Page 282
40816 HICKS Mcghp Chap_8 Pgs 282 7/12/2001
282
CHAPTER EIGHT
vH
D √W
where constant (varies for each site), and H constant (varies for each site). Distance to exposure, ft (m), divided by the square root of maximum pounds (kg) per delay is known as scaled distance. Most courts have accepted the fact that a particle velocity not exceeding 2 in/s (50.8 mm/s) does not damage any part of any structure. This implies that, for this velocity, vibration damage is unlikely at scaled distances larger than 8.
TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 283
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 283
CHAPTER 9
BUILDING AND STRUCTURES FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_09_p283-320
10/22/01
12:49 PM
Page 284
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 284
284
4081
CHAPTER NINE
LOAD-AND-RESISTANCE FACTOR DESIGN FOR SHEAR IN BUILDINGS
F s
Based on the American Institute of Steel Construction (AISC) specifications for load-and-resistance factor design (LRFD) for buildings, the shear capacity Vu, kip (kN 4.448 kip), of flexural members may be computed from the following:
A B
Vu 0.54Fyw Aw
when
Vu
0.54Fyw Aw h/t w
when
Vu
23,760kAw (h/t w)2
when
where
T b c f e u e
h tw h 1.25 tw h 1.25 tw
Fyw specified minimum yield stress of web, ksi (MPa 6.894 ksi) Aw web area, in2 (mm2) dtw
w
187√k /Fyw k 5 if a/h exceeds 3.0 or 67,600/(h/tw)2, or if stiffeners are not required W
5 5/(a/h)2, otherwise Stiffeners are required when the shear exceeds Vu. In unstiffened girders, h/tw may not exceed 260. In girders with stiffeners, maximum h/tw permitted is 2,000/√Fyf for a/h 1.5 or 14,000/√Fyf (Fyf 16.5) for a/h > 1.5, where Fyf is the specified minimum yield stress, ksi, of the flange. TLFeBOOK
40816_09_p283-320 p 284
10/22/01
12:49 PM
Page 285
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 285
BUILDING AND STRUCTURES FORMULAS
285
For shear capacity with tension-field action, see the AISC specification for LRFD. ) ) , :
ALLOWABLE-STRESS DESIGN FOR BUILDING COLUMNS The AISC specification for allowable-stress design (ASD) for buildings provides two formulas for computing allowable compressive stress Fa, ksi (MPa), for main members. The formula to use depends on the relationship of the largest effective slenderness ratio Kl/r of the cross section of any unbraced segment to a factor Cc defined by the following equation and Table 9.1:
,
Cc
√
2 2E 756.6 Fy √Fy
where E modulus of elasticity of steel 29,000 ksi (128.99 GPa) f
Fy yield stress of steel, ksi (MPa) When Kl/r is less than Cc ,
n s r e .
TABLE 9.1 Values of Cc Fy
Cc
36
126.1
50
107.0 TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 286
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 286
286
4081
CHAPTER NINE
(Kl/r) 1 F 2C F
L F
2
2 c
a
F.S.
where F.S. safety factor When Kl /r exceeds Cc, Fa
y
P b F b m
5 3(Kl/r) (Kl/r)3 . 3 8Cc 8C3c
12 2E 150,000 23(Kl/r)2 (Kl/r)2
The effective-length factor K, equal to the ratio of effective-column length to actual unbraced length, may be greater or less than 1.0. Theoretical K values for six idealized conditions, in which joint rotation and translation are either fully realized or nonexistent, are tabulated in Fig. 9.1.
w
T d
A B T p p p c o g
FIGURE 9.1 Values of effective-length factor K for columns.
TLFeBOOK
40816_09_p283-320 p 286
10/22/01
12:49 PM
Page 287
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 287
287
BUILDING AND STRUCTURES FORMULAS
LOAD-AND-RESISTANCE FACTOR DESIGN FOR BUILDING COLUMNS Plastic analysis of prismatic compression members in buildings is permitted if √Fy (l/r) does not exceed 800 and Fu 65 ksi (448 MPa). For axially loaded members with b/t r, the maximum load Pu, ksi (MPa 6.894 ksi), may be computed from Pu 0.85AgFcr e e .
where Ag gross cross-sectional area of the member Fcr 0.658Fy for 2.25 0.877 Fy / for 2.25 (Kl/r)2(Fy /286,220) The AISC specification for LRFD presents formulas for designing members with slender elements.
ALLOWABLE-STRESS DESIGN FOR BUILDING BEAMS The maximum fiber stress in bending for laterally supported beams and girders is Fb 0.66Fy if they are compact, except for hybrid girders and members with yield points exceeding 65 ksi (448.1 MPa). Fb 0.60Fy for noncompact sections. Fy is the minimum specified yield strength of the steel, ksi (MPa). Table 9.2 lists values of Fb for two grades of steel. TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 288
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 288
288
4081
CHAPTER NINE
TABLE 9.2 Allowable Bending Stresses in Braced Beams for Buildings Yield strength, ksi (MPa)
Compact, 0.66Fy (MPa)
Noncompact, 0.60Fy (MPa)
36 (248.2) 50 (344.7)
24 (165.5) 33 (227.5)
22 (151.7) 30 (206.8)
t i
The allowable extreme-fiber stress of 0.60Fy applies to laterally supported, unsymmetrical members, except channels, and to noncompact box sections. Compression on outer surfaces of channels bent about their major axis should not exceed 0.60Fy or the value given by Eq. (9.5). The allowable stress of 0.66Fy for compact members should be reduced to 0.60Fy when the compression flange is unsupported for a length, in (mm), exceeding the smaller of lmax
76.0bf √Fy
(9.1)
lmax
20,000 Fyd/Af
(9.2)
F
w n t t
W t a m
where bf width of compression flange, in (mm) d beam depth, in (mm) Af area of compression flange, in2 (mm2) The allowable stress should be reduced even more when l/rT exceeds certain limits, where l is the unbraced length, in (mm), of the compression flange, and rT is the radius of gyration, in (mm), of a portion of the beam consisting of TLFeBOOK
w b c W
40816_09_p283-320 p 288
10/22/01
12:49 PM
Page 289
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 289
BUILDING AND STRUCTURES FORMULAS
289
the compression flange and one-third of the part of the web in compression. For √102,000Cb /Fy l/rT √510,00Cb /Fy, use Fb
o r t s s f )
)
F (l/r ) 23 1,530,000C F y
2
y
b
(9.3)
For l/rT √510,000Cb /Fy, use Fb
170,000Cb (l/rT )2
(9.4)
where Cb modifier for moment gradient (Eq. 9.6). When, however, the compression flange is solid and nearly rectangular in cross section, and its area is not less than that of the tension flange, the allowable stress may be taken as 12,000Cb (9.5) Fb ld/Af When Eq. (9.5) applies (except for channels), Fb should be taken as the larger of the values computed from Eqs. (9.5) and (9.3) or (9.4), but not more than 0.60Fy. The moment-gradient factor Cb in Eqs. (9.1) to (9.5) may be computed from Cb 1.75 1.05
n , f f
T
M1 0.3 M2
MM 2.3 1
2
(9.6)
2
where M1 smaller beam end moment, and M2 larger beam end moment. The algebraic sign of M1 /M2 is positive for doublecurvature bending and negative for single-curvature bending. When the bending moment at any point within an unbraced TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 290
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 290
290
4081
CHAPTER NINE
length is larger than that at both ends, the value of Cb should be taken as unity. For braced frames, Cb should be taken as unity for computation of Fbx and Fby. Equations (9.4) and (9.5) can be simplified by introducing a new term: Q
(l/rT)2Fy 510,000Cb
a w i
(9.7) w
Now, for 0.2 Q 1, Fb
(2 Q)Fy 3
(9.8)
Fy 3Q
(9.9)
For Q 1: Fb
As for the preceding equations, when Eq. (9.1) applies (except for channels), Fb should be taken as the largest of the values given by Eqs. (9.1) and (9.8) or (9.9), but not more than 0.60Fy.
T t g t
LOAD-AND-RESISTANCE FACTOR DESIGN FOR BUILDING BEAMS For a compact section bent about the major axis, the unbraced length Lb of the compression flange, where plastic hinges may form at failure, may not exceed Lpd , given by Eqs. (9.10) and (9.11) that follow. For beams bent about the minor axis and square and circular beams, Lb is not restricted for plastic analysis. TLFeBOOK
l l n m t e
40816_09_p283-320 p 290
10/22/01
12:49 PM
Page 291
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 291
BUILDING AND STRUCTURES FORMULAS b
e -
291
For I-shaped beams, symmetrical about both the major and the minor axis or symmetrical about the minor axis but with the compression flange larger than the tension flange, including hybrid girders, loaded in the plane of the web: Lpd
)
3600 2200(M1/Mp) ry Fyc
(9.10)
where Fyc minimum yield stress of compression flange, ksi (MPa) )
M1 smaller of the moments, inkip (mmMPa) at the ends of the unbraced length of beam Mp plastic moment, inkip (mmMPa)
) s f t
ry radius of gyration, in (mm), about minor axis The plastic moment Mp equals Fy Z for homogeneous sections, where Z plastic modulus, in3 (mm3); and for hybrid girders, it may be computed from the fully plastic distribution. M1/Mp is positive for beams with reverse curvature. For solid rectangular bars and symmetrical box beams: Lpd
e c y e d
5000 3000(M1/Mp) ry ry 3000 Fy Fy
(9.11)
The flexural design strength 0.90Mn is determined by the limit state of lateral-torsional buckling and should be calculated for the region of the last hinge to form and for regions not adjacent to a plastic hinge. The specification gives formulas for Mn that depend on the geometry of the section and the bracing provided for the compression flange. For compact sections bent about the major axis, for example, Mn depends on the following unbraced lengths: TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 292
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 292
292
CHAPTER NINE
Lb the distance, in (mm), between points braced against lateral displacement of the compression flange or between points braced to prevent twist Lp limiting laterally unbraced length, in (mm), for full plastic-bending capacity 300ry / √Fyf for I shapes and channels 3750(ry /Mp)/√JA for solid rectangular bars and box beams Fyf flange yield stress, ksi (MPa) J torsional constant, in4 (mm4) (see AISC “Manual of Steel Construction” on LRFD) A cross-sectional area, in2 (mm2) Lr limiting laterally unbraced length, in (mm), for inelastic lateral buckling For I-shaped beams symmetrical about the major or the minor axis, or symmetrical about the minor axis with the compression flange larger than the tension flange and channels loaded in the plane of the web: Lr where
4081
ry x1 Fyw Fr
√1 √1 X2 FL2
(9.12)
F m
a
Fyw specified minimum yield stress of web, ksi (MPa) Fr compressive residual stress in flange 10 ksi (68.9 MPa) for rolled shapes, 16.5 ksi (113.6 MPa), for welded sections FL smaller of Fyf Fr or Fyw Fyf specified minimum yield stress of flange, ksi (MPa) TLFeBOOK
w w t r a m m
40816_09_p283-320 p 292
10/22/01
12:49 PM
Page 293
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 293
293
BUILDING AND STRUCTURES FORMULAS
X1 ( /Sx)√EGJA/2 X2 (4Cw /Iy) (Sx /GJ)2 E elastic modulus of the steel G shear modulus of elasticity Sx section modulus about major axis, in3 (mm3) (with respect to the compression flange if that flange is larger than the tension flange) Cw warping constant, in6 (mm6) (see AISC manual on LRFD) Iy moment of inertia about minor axis, in4 (mm4) e e -
) ,
For the previously mentioned shapes, the limiting buckling moment Mr, ksi (MPa), may be computed from M r FL Sx
For compact beams with Lb Lr, bent about the major axis:
Mn Cb Mp (Mp Mr) 5
,
(9.13)
Lb Lp Lr Lp
M
p
(9.14)
where Cb 1.75 1.05(M1 /M2) 0.3(M1 /M2) 2.3, where M1 is the smaller and M2 the larger end moment in the unbraced segment of the beam; M1/M2 is positive for reverse curvature and equals 1.0 for unbraced cantilevers and beams with moments over much of the unbraced segment equal to or greater than the larger of the segment end moments. TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 294
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 294
294
4081
CHAPTER NINE
(See Galambos, T. V., Guide to Stability Design Criteria for Metal Structures, 4th ed., John Wiley & Sons, New York, for use of larger values of Cb.) For solid rectangular bars bent about the major axis: Lr 57,000
√JA ry Mr
A I T a
(9.15)
and the limiting buckling moment is given by: M r Fy Sx
(9.16)
For symmetrical box sections loaded in the plane of symmetry and bent about the major axis, Mr should be determined from Eq. (9.13) and Lr from Eq. (9.15) For compact beams with Lb > Lr, bent about the major axis: M n M cr Cb M r
(9.17)
where Mcr critical elastic moment, kipin (MPamm). For shapes to which Eq. (9.17) applies: Mcr Cb
Lb
√
EIy GJ Iy Cw
E L
T
2
(9.18)
b
For solid rectangular bars and symmetrical box sections: 57,000Cb √JA Lb / ry
w
w
(9.19)
W
For determination of the flexural strength of noncompact plate girders and other shapes not covered by the preceding requirements, see the AISC manual on LRFD.
m s t s
Mcr
TLFeBOOK
40816_09_p283-320 p 294
10/22/01
12:49 PM
Page 295
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 295
BUILDING AND STRUCTURES FORMULAS
a ,
295
ALLOWABLE-STRESS DESIGN FOR SHEAR IN BUILDINGS The AISC specification for ASD specifies the following allowable shear stresses Fv, ksi (ksi 6.894 MPa):
)
h 380 tw √Fy
Fv 0.40Fy
)
Fv
Cv Fy 0.40Fy 289
h 380 tw √Fy
-
where Cv 45,000kv /Fy(h/tw)2
r
kv 4.00 5.34/(a/ h)
for a/h 1.0
5.34 4.00/(a/ h)
for a/h 1.0
for Cv 0.8
√36,000kv /Fy(h/tw)
2
2 2
)
for Cv 0.8
a clear distance between transverse stiffeners The allowable shear stress with tension-field action is
)
Fv
Fy 289
C 1.15√11 C(a/h) 0.40F v
v
2
y
where Cv 1 ) t g
When the shear in the web exceeds Fv , stiffeners are required. Within the boundaries of a rigid connection of two or more members with webs lying in a common plane, shear stresses in the webs generally are high. The commentary on the AISC specification for buildings states that such webs should be reinforced when the calculated shear stresses, TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 296
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 296
296
4081
CHAPTER NINE
S FIGURE 9.2 Rigid connection of steel members with webs in a common plane.
such as those along plane AA in Fig. 9.2, exceed Fv, that is, when F is larger than dc tw Fv, where dc is the depth and tw is the web thickness of the member resisting F. The shear may be calculated from
F
R t l s a u e o
M2 M1 Vs 0.95d 1 0.95d 2 w
where Vs shear on the section M1 M1L M1G M1L moment due to the gravity load on the leeward side of the connection TLFeBOOK
40816_09_p283-320 p 296
10/22/01
12:49 PM
Page 297
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 297
BUILDING AND STRUCTURES FORMULAS
297
M1G moment due to the lateral load on the leeward side of the connection M2 M2L M2G M2L moment due to the lateral load on the windward side of the connection M2G moment due to the gravity load on the windward side of the connection
STRESSES IN THIN SHELLS a
, w
r
Results of membrane and bending theories are expressed in terms of unit forces and unit moments, acting per unit of length over the thickness of the shell. To compute the unit stresses from these forces and moments, usual practice is to assume normal forces and shears to be uniformly distributed over the shell thickness and bending stresses to be linearly distributed. Then, normal stresses can be computed from equations of the form: fx
Nx M 3 x z t t /12
(9.20)
where z distance from middle surface t shell thickness d
Mx unit bending moment about an axis parallel to direction of unit normal force Nx TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 298
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 298
298
4081
CHAPTER NINE
Similarly, shearing stresses produced by central shears T and twisting moments D may be calculated from equations of the form: T D vxy 3 z t t /12
F
(9.21) L
Normal shearing stresses may be computed on the assumption of a parabolic stress distribution over the shell thickness: V vxz 3 t /6
T M
t2 z2 4
(9.22)
S B †
where V unit shear force normal to middle surface.
BEARING PLATES
w i
To resist a beam reaction, the minimum bearing length N in the direction of the beam span for a bearing plate is determined by equations for prevention of local web yielding and web crippling. A larger N is generally desirable but is limited by the available wall thickness. When the plate covers the full area of a concrete support, the area, in2 (mm2), required by the bearing plate is A1
R 0.35 f c
where R beam reaction, kip (kN), f c specified compressive strength of the concrete, ksi (MPa). When the plate covers less than the full area of the concrete support, then, as determined from Table 9.3, TLFeBOOK
m c i s
T t
40816_09_p283-320 p 298
10/22/01
12:49 PM
Page 299
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 299
299
BUILDING AND STRUCTURES FORMULAS
T s
TABLE 9.3 Allowable Bearing Stress, Fp, on Concrete and Masonry†
0.35f c
Full area of concrete support
) 0.35f c
Less than full area of concrete support
e l
)
0.40
Brick in cement mortar
0.25
†
Units in MPa 6.895 ksi.
0.35 fR √A
2
c
2
where A2 full cross-sectional area of concrete support, in2 (mm2). With N established, usually rounded to full inches (millimeters), the minimum width of plate B, in (mm), may be calculated by dividing A1 by N and then rounded off to full inches (millimeters), so that BN A1. Actual bearing pressure fp, ksi (MPa), under the plate then is
fp
e ,
A1 0.70f c A2
Sandstone and limestone
A1
n g s
√
R BN
The plate thickness usually is determined with the assumption of cantilever bending of the plate: t
12 B k √ 3fF
p
b
TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 300
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 300
300
4081
CHAPTER NINE
where t minimum plate thickness, in (mm) k distance, in (mm), from beam bottom to top of web fillet
e b
Fb allowable bending stress of plate, ksi (MPa) w p
COLUMN BASE PLATES The area A1, in2 (mm2), required for a base plate under a column supported by concrete should be taken as the larger of the values calculated from the equation cited earlier, with R taken as the total column load, kip (kN), or A1
R 0.70 fc
Unless the projections of the plate beyond the column are small, the plate may be designed as a cantilever assumed to be fixed at the edges of a rectangle with sides equal to 0.80b and 0.95d, where b is the column flange width, in (mm), and d is the column depth, in (mm). To minimize material requirements, the plate projections should be nearly equal. For this purpose, the plate length N, in (mm) (in the direction of d), may be taken as
t s l m a
w ( p l o
N √A1 0.5(0.95d 0.80b)
B
The width B, in (mm), of the plate then may be calculated by dividing A1 by N. Both B and N may be selected in full inches (millimeters) so that BN A1. In that case, the bearing pressure fp, ksi (MPa), may be determined from the preceding
I s d s
TLFeBOOK
40816_09_p283-320 p 300
10/22/01
12:49 PM
Page 301
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 301
BUILDING AND STRUCTURES FORMULAS
f
equation. Thickness of plate, determined by cantilever bending, is given by t 2p
f R
s ,
√
fp Fy
where Fy minimum specified yield strength, ksi (MPa), of plate; and p larger of 0.5(N 0.95d) and 0.5(B 0.80b). When the plate projections are small, the area A2 should be taken as the maximum area of the portion of the supporting surface that is geometrically similar to and concentric with the loaded area. Thus, for an H-shaped column, the column load may be assumed distributed to the concrete over an H-shaped area with flange thickness L, in (mm), and web thickness 2L: L
e o o n
301
1 1 (d b) 4 4
√
(d b)2
4R Fp
where Fp allowable bearing pressure, ksi (MPa), on support. (If L is an imaginary number, the loaded portion of the supporting surface may be assumed rectangular as discussed earlier.) Thickness of the base plate should be taken as the larger of the values calculated from the preceding equation and tL
√
3fp Fb
BEARING ON MILLED SURFACES d l g g
In building construction, allowable bearing stress for milled surfaces, including bearing stiffeners, and pins in reamed, drilled, or bored holes, is Fp 0.90Fy, where Fy is the yield strength of the steel, ksi (MPa). TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 302
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 302
302
4081
CHAPTER NINE
For expansion rollers and rockers, the allowable bearing stress, kip/linear in (kN/mm), is Fp
Fy 13 0.66d 20
where d is the diameter, in (mm), of the roller or rocker. When parts in contact have different yield strengths, Fy is the smaller value. t m
PLATE GIRDERS IN BUILDINGS For greatest resistance to bending, as much of a plate girder cross section as practicable should be concentrated in the flanges, at the greatest distance from the neutral axis. This might require, however, a web so thin that the girder would fail by web buckling before it reached its bending capacity. To preclude this, the AISC specification limits h/t. For an unstiffened web, this ratio should not exceed
7 s a l
h 14,000 t √Fy (Fy 16.5) where Fy yield strength of compression flange, ksi (MPa). Larger values of h/t may be used, however, if the web is stiffened at appropriate intervals. For this purpose, vertical angles may be fastened to the web or vertical plates welded to it. These transverse stiffeners are not required, though, when h/t is less than the value computed from the preceding equation or Table 9.4. TLFeBOOK
w
40816_09_p283-320 p 302
10/22/01
12:49 PM
Page 303
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 303
303
BUILDING AND STRUCTURES FORMULAS
g
TABLE 9.4 Critical h/t for Plate Girders in Buildings 14,000
2,000
Fy, ksi
(MPa)
√Fy(Fy 16.5)
√Fy
36 50
(248) (345)
322 243
333 283
. s With transverse stiffeners spaced not more than 1.5 times the girder depth apart, the web clear-depth/thickness ratio may be as large as
r e s d .
h 2000 t √Fy If, however, the web depth/thickness ratio h/t exceeds 760 / √Fb, where Fb, ksi (MPa), is the allowable bending stress in the compression flange that would ordinarily apply, this stress should be reduced to Fb , given by the following equations: Fb RPG Re Fb
Aw Af
RPG 1 0.0005 . s e s e
Re
1.0 ht 760 √F b
12 12(A/A2(A)(3/A) ) 1.0 w
3
f
w
f
where Aw web area, in (mm ) 2
2
Af area of compression flange, in2 (mm2) TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 304
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 304
304
4081
CHAPTER NINE
0.6Fyw /Fb 1.0 Fyw minimum specified yield stress, ksi, (MPa), of web steel In a hybrid girder, where the flange steel has a higher yield strength than the web, the preceding equation protects against excessive yielding of the lower strength web in the vicinity of the higher strength flanges. For nonhybrid girders, Re 1.0.
LOAD DISTRIBUTION TO BENTS AND SHEAR WALLS Provision should be made for all structures to transmit lateral loads, such as those from wind, earthquakes, and traction and braking of vehicles, to foundations and their supports that have high resistance to displacement. For this purpose, various types of bracing may be used, including struts, tension ties, diaphragms, trusses, and shear walls.
F o a V
d T d
Deflections of Bents and Shear Walls Horizontal deflections in the planes of bents and shear walls can be computed on the assumption that they act as cantilevers. Deflections of braced bents can be calculated by the dummy-unit-load method or a matrix method. Deflections of rigid frames can be computed by adding the drifts of the stories, as determined by moment distribution or a matrix method. For a shear wall (Fig. 9.3), the deflection in its plane induced by a load in its plane is the sum of the flexural TLFeBOOK
w
40816_09_p283-320 p 304
10/22/01
12:49 PM
Page 305
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 305
305
BUILDING AND STRUCTURES FORMULAS
f d t f .
l n s , ,
FIGURE 9.3 Building frame resists lateral forces with (a) wind bents or (g) shear walls or a combination of the two. Bents may be braced in any of several ways, including (b) X bracing, (c) K bracing, (d) inverted V bracing, (e) knee bracing, and ( f ) rigid connections.
deflection as a cantilever and the deflection due to shear. Thus, for a wall with solid rectangular cross section, the deflection at the top due to uniform load is
r s d . e n e l
1.5wH Et
HL HL 3
where w uniform lateral load H height of the wall E modulus of elasticity of the wall material t wall thickness L length of wall TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 306
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 306
306
4081
CHAPTER NINE
For a shear wall with a concentrated load P at the top, the deflection at the top is c
4P Et
HL 0.75 HL 3
If the wall is fixed against rotation at the top, however, the deflection is f
P Et
W i
HL 3 HL 3
Units used in these equations are those commonly applied in United States Customary System (USCS) and the System International (SI) measurements, that is, kip (kN), lb/in2 (MPa), ft (m), and in (mm). Where shear walls contain openings, such as those for doors, corridors, or windows, computations for deflection and rigidity are more complicated. Approximate methods, however, may be used.
COMBINED AXIAL COMPRESSION OR TENSION AND BENDING The AISC specification for allowable stress design for buildings includes three interaction formulas for combined axial compression and bending. When the ratio of computed axial stress to allowable axial stress fu /Fa exceeds 0.15, both of the following equations must be satisfied: TLFeBOOK
I a
40816_09_p283-320 p 306
10/22/01
12:49 PM
Page 307
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 307
BUILDING AND STRUCTURES FORMULAS
e
307
Cmx fbx Cmy fby fa 1 Fa (1 fa /Fex)Fbx (1 fa /Fey)Fby f f fa bx by 1 0.60Fy Fbx Fby
e
When fa /Fa 0.15, the following equation may be used instead of the preceding two: fa f f bx by 1 Fa Fbx Fby
y e , r n ,
r d e -
In the preceding equations, subscripts x and y indicate the axis of bending about which the stress occurs, and Fa axial stress that would be permitted if axial force alone existed, ksi (MPa) Fb compressive bending stress that would be permitted if bending moment alone existed, ksi (MPa) Fe 149,000/(Klb /rb)2, ksi (MPa); as for Fa, Fb, and 0.6Fy, Fe may be increased one-third for wind and seismic loads lb actual unbraced length in plane of bending, in (mm) rb radius of gyration about bending axis, in (mm) K effective-length factor in plane of bending fa computed axial stress, ksi (MPa) fb computed compressive bending stress at point under consideration, ksi (MPa) Cm adjustment coefficient TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 308
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 308
308
4081
CHAPTER NINE
WEBS UNDER CONCENTRATED LOADS
w
Criteria for Buildings The AISC specification for ASD for buildings places a limit on compressive stress in webs to prevent local web yielding. For a rolled beam, bearing stiffeners are required at a concentrated load if the stress fa, ksi (MPa), at the toe of the web fillet exceeds Fa 0.66Fyw, where Fyw is the minimum specified yield stress of the web steel, ksi (MPa). In the calculation of the stressed area, the load may be assumed distributed over the distance indicated in Fig. 9.4. For a concentrated load applied at a distance larger than the depth of the beam from the end of the beam: fa
F
r c e
R t w (N 5k)
F e
w F b
FIGURE 9.4 For investigating web yielding, stresses are assumed to be distributed over lengths of web indicated at the bearings, where N is the length of bearing plates, and k is the distance from outer surface of beam to the toe of the fillet.
TLFeBOOK
I w
40816_09_p283-320 p 308
10/22/01
12:49 PM
Page 309
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 309
309
BUILDING AND STRUCTURES FORMULAS
where R concentrated load of reaction, kip (kN) tw web thickness, in (mm) t a e m -
N length of bearing, in (mm), (for end reaction, not less than k) k distance, in (mm), from outer face of flange to web toe of fillet For a concentrated load applied close to the beam end: fa
n
R t w (N 2.5k)
To prevent web crippling, the AISC specification requires that bearing stiffeners be provided on webs where concentrated loads occur when the compressive force exceeds R, kip (kN), computed from the following: For a concentrated load applied at a distance from the beam end of at least d/2, where d is the depth of beam:
R 67.5t2w 1 3
Nd tt √F w
1.5
yw tf /tw
f
where tf flange thickness, in (mm) For a concentrated load applied closer than d/2 from the beam end:
R 34t2w 1 3 o s f
Nd tt √F w f
1.5
yw tf / tw
If stiffeners are provided and extend at least one-half of the web, R need not be computed. TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 310
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 310
310
4081
CHAPTER NINE
Another consideration is prevention of sidesway web buckling. The AISC specification requires bearing stiffeners when the compressive force from a concentrated load exceeds limits that depend on the relative slenderness of web and flange rwf and whether or not the loaded flange is restrained against rotation: rwf
dc /tw l /bf
where l largest unbraced length, in (mm), along either top or bottom flange at point of application of load
D A o e b c a c a e o
bf flange width, in (mm) dc web depth clear of fillets d 2k
w
Stiffeners are required if the concentrated load exceeds R, kip (kN), computed from R
6800t 3w (1 0.4r 3wf) h
where h clear distance, in (mm), between flanges, and rwf is less than 2.3 when the loaded flange is restrained against rotation. If the loaded flange is not restrained and rwf is less than 1.7, R 0.4r3wf
6800t3w h
R need not be computed for larger values of rwf. TLFeBOOK
40816_09_p283-320 p 310
10/22/01
12:49 PM
Page 311
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 311
BUILDING AND STRUCTURES FORMULAS
b s d f s
r f
311
DESIGN OF STIFFENERS UNDER LOADS AISC requires that fasteners or welds for end connections of beams, girders, and trusses be designed for the combined effect of forces resulting from moment and shear induced by the rigidity of the connection. When flanges or momentconnection plates for end connections of beams and girders are welded to the flange of an I- or H-shape column, a pair of column-web stiffeners having a combined cross-sectional area Ast not less than that calculated from the following equations must be provided whenever the calculated value of Ast is positive: Ast
Pbf Fyc twc(tb 5K) Fyst
where Fyc column yield stress, ksi (MPa) ,
Fyst stiffener yield stress, ksi (MPa) K distance, in (mm), between outer face of column flange and web toe of its fillet, if column is rolled shape, or equivalent distance if column is welded shape
f
t s
Pbf computed force, kip (kN), delivered by flange of moment-connection plate multiplied by 53, when computed force is due to live and dead load only, or by 43, when computed force is due to live and dead load in conjunction with wind or earthquake forces twc thickness of column web, in (mm) tb thickness of flange or moment-connection plate delivering concentrated force, in (mm) TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 312
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 312
312
4081
CHAPTER NINE
Notwithstanding the preceding requirements, a stiffener or a pair of stiffeners must be provided opposite the beamcompression flange when the column-web depth clear of fillets dc is greater than dc
4100t3wc √Fyc Pbf
and a pair of stiffeners should be provided opposite the tension flange when the thickness of the column flange tf is less than tf 0.4
√
Pbf Fyc
Stiffeners required by the preceding equations should comply with the following additional criteria: 1. The width of each stiffener plus half the thickness of the column web should not be less than one-third the width of the flange or moment-connection plate delivering the concentrated force. 2. The thickness of stiffeners should not be less than tb /2. 3. The weld-joining stiffeners to the column web must be sized to carry the force in the stiffener caused by unbalanced moments on opposite sides of the column.
( W l c b a f
w ( e 1 s
C I a t r
C
FASTENERS IN BUILDINGS
T
The AISC specification for allowable stresses for buildings specifies allowable unit tension and shear stresses on the cross-sectional area on the unthreaded body area of bolts and threaded parts.
M c s b
TLFeBOOK
40816_09_p283-320 p 312
10/22/01
12:49 PM
Page 313
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 313
BUILDING AND STRUCTURES FORMULAS
r f
s
e h e . e -
313
(Generally, rivets should not be used in direct tension.) When wind or seismic load are combined with gravity loads, the allowable stresses may be increased one-third. Most building construction is done with bearing-type connections. Allowable bearing stresses apply to both bearing-type and slip-critical connections. In buildings, the allowable bearing stress Fp, ksi (MPa), on projected area of fasteners is Fp 1.2Fu where Fu is the tensile strength of the connected part, ksi (MPa). Distance measured in the line of force to the nearest edge of the connected part (end distance) should be at least 1.5d, where d is the fastener diameter. The center-to-center spacing of fasteners should be at least 3d.
COMPOSITE CONSTRUCTION In composite construction, steel beams and a concrete slab are connected so that they act together to resist the load on the beam. The slab, in effect, serves as a cover plate. As a result, a lighter steel section may be used.
Construction In Buildings There are two basic methods of composite construction. s e s
Method 1. The steel beam is entirely encased in the concrete. Composite action in this case depends on the steel-concrete bond alone. Because the beam is completely braced laterally, the allowable stress in the flanges is TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 314
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 314
314
4081
CHAPTER NINE
0.66Fy, where Fy is the yield strength, ksi (MPa), of the steel. Assuming the steel to carry the full dead load and the composite section to carry the live load, the maximum unit stress, ksi (MPa), in the steel is fs
MD M L 0.66Fy Ss Str
where MD dead-load moment, inkip (kNmm) ML live-load moment, inkip (kNmm)
b e t o c T m f 1
Ss section modulus of steel beam, in3 (mm3) Str section modulus of transformed composite section, in3 (mm3)
2 3
An alternative, shortcut method is permitted by the AISC specification. It assumes that the steel beam carries both live and dead loads and compensates for this by permitting a higher stress in the steel: fs
MD ML 0.76Fy Ss
Method 2. The steel beam is connected to the concrete slab by shear connectors. Design is based on ultimate load and is independent of the use of temporary shores to support the steel until the concrete hardens. The maximum stress in the bottom flange is fs
MD ML 0.66Fy Str
To obtain the transformed composite section, treat the concrete above the neutral axis as an equivalent steel area TLFeBOOK
F c
40816_09_p283-320 p 314
10/22/01
12:49 PM
Page 315
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 315
BUILDING AND STRUCTURES FORMULAS
e e t
e
315
by dividing the concrete area by n, the ratio of modulus of elasticity of steel to that of the concrete. In determination of the transformed section, only a portion of the concrete slab over the beam may be considered effective in resisting compressive flexural stresses (positive-moment regions). The width of slab on either side of the beam centerline that may be considered effective should not exceed any of the following: 1. One-eighth of the beam span between centers of supports 2. Half the distance to the centerline of the adjacent beam 3. The distance from beam centerline to edge of slab (Fig. 9.5)
e s -
e d m
e a
FIGURE 9.5 Limitations on effective width of concrete slab in a composite steel-concrete beam.
TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 316
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 316
316
4081
CHAPTER NINE
NUMBER OF CONNECTORS REQUIRED FOR BUILDING CONSTRUCTION
S
The total number of connectors to resist Vh is computed from Vh /q, where q is the allowable shear for one connector, kip (kN). Values of q for connectors in buildings are given in structural design guides. The required number of shear connectors may be spaced uniformly between the sections of maximum and zero moment. Shear connectors should have at least 1 in (25.4 mm) of concrete cover in all directions; and unless studs are located directly over the web, stud diameters may not exceed 2.5 times the beam-flange thickness. With heavy concentrated loads, the uniform spacing of shear connectors may not be sufficient between a concentrated load and the nearest point of zero moment. The number of shear connectors in this region should be at least N2
T n t
w
N1[(M/Mmax) 1] 1
where M moment at concentrated load, ftkip (kNm) Mmax maximum moment in span, ftkip (kNm) N1 number of shear connectors required between Mmax and zero moment Str /Ss or Seff /Ss, as applicable Seff effective section modulus for partial composite action, in3 (mm3) TLFeBOOK
f s t a
40816_09_p283-320 p 316
10/22/01
12:49 PM
Page 317
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 317
BUILDING AND STRUCTURES FORMULAS
317
Shear on Connectors
d , n d o 4 s t g a . e
The total horizontal shear to be resisted by the shear connectors in building construction is taken as the smaller of the values given by the following two equations:
Vh
0.85 fc Ac 2
Vh
As Fy 2
where Vh total horizontal shear, kip (kN), between maximum positive moment and each end of steel beams (or between point of maximum positive moment and point of contraflexure in continuous beam) fc specified compressive strength of concrete at 28 days, ksi (MPa) Ac actual area of effective concrete flange, in2 (mm2)
)
n
e
As area of steel beam, in2 (mm2) In continuous composite construction, longitudinal reinforcing steel may be considered to act compositely with the steel beam in negative-moment regions. In this case, the total horizontal shear, kip (kN), between an interior support and each adjacent point of contraflexure should be taken as Vh
Asr Fyr 2 TLFeBOOK
40816_09_p283-320
10/22/01
12:49 PM
Page 318
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 318
318
4081
CHAPTER NINE
where Asr area of longitudinal reinforcement at support within effective area, in2 (mm2); and Fyr specified minimum yield stress of longitudinal reinforcement, ksi (MPa).
PONDING CONSIDERATIONS IN BUILDINGS Flat roofs on which water may accumulate may require analysis to ensure that they are stable under ponding conditions. A flat roof may be considered stable and an analysis does not need to be made if both of the following two equations are satisfied: Cp 0.9Cs 0.25 Id 25S4/106 where Cp 32Ls L4p /107Ip Cs 32SL4s /107Is Lp length, ft (m), of primary member or girder Ls length, ft (m), of secondary member or purlin S spacing, ft (m), of secondary members Ip moment of inertia of primary member, in4 (mm4) Is moment of inertia of secondary member, in4 (mm4) Id moment of inertia of steel deck supported on secondary members, in4/ft (mm4/m) TLFeBOOK
F d l 0 t
40816_09_p283-320 p 318
10/22/01
12:49 PM
Page 319
40816 HICKS Mcghp Ch09 THIRD PASS bcj 07/12/01 p 319
BUILDING AND STRUCTURES FORMULAS
t .
319
For trusses and other open-web members, Is should be decreased 15 percent. The total bending stress due to dead loads, gravity live loads, and ponding should not exceed 0.80Fy, where Fy is the minimum specified yield stress for the steel.
e s -
r n
4
4
n TLFeBOOK
This page intentionally left blank.
TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 321
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p321
CHAPTER 10
BRIDGE AND SUSPENSIONCABLE FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_10_p321-354
10/22/01
12:49 PM
Page 322
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p322
322
408
CHAPTER TEN
SHEAR STRENGTH DESIGN FOR BRIDGES
A F
Based on the American Association of State Highway and Transportation Officials (AASHTO) specifications for loadfactor design (LFD), the shear capacity, kip (kN), may be computed from
I s f
Vu 0.58Fy htwC for flexural members with unstiffened webs with h/ tw 150 or for girders with stiffened webs but a/h exceeding 3 or 67,600(h / tw)2: C 1.0
when
h tw
h/t w
when
45,000k Fy (h/t w)2
when
h 1.25 tw
h 1.25 tw
S
For girders with transverse stiffeners and a/h less than 3 and 67,600(h / tw)2, the shear capacity is given by
Vu 0.58Fy dtw C
1C 1.15 √1 (a/h)2
T
S
Stiffeners are required when the shear exceeds Vu. Chap. 9, “Building and Structures Formulas,” for symbols used in the preceding equations. TLFeBOOK
40816_10_p321-354 p322
10/22/01
12:49 PM
Page 323
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p323
BRIDGE AND SUSPENSION-CABLE FORMULAS
323
ALLOWABLE-STRESS DESIGN FOR BRIDGE COLUMNS d e
In the AASHTO bridge-design specifications, allowable stresses in concentrically loaded columns are determined from the following equations: When Kl/r is less than Cc,
0 r
Fa
Fy 2.12
1 (Kl/r) 2C 2
2 c
When Kl / r is equal to or greater than Cc,
Fa
2E 135,000 2.12(Kl/r)2 (Kl/r)2
See Table 10.1.
3 TABLE 10.1 Column Formulas for Bridge Design
-
Yield Strength, ksi
Allowable Stress, ksi (MPa) (MPa)
Cc
Kl/r Cc
Kl/r Cc
36 50 90 100
(248) (345) (620) (689)
126.1 107.0 79.8 75.7
16.98–0.00053(Kl/r)2 23.58–0.00103(Kl/r)2 42.45–0.00333(Kl/r)2 47.17–0.00412(Kl/r)2
135,000 (Kl/r)2
TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 324
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p324
324
408
CHAPTER TEN
LOAD-AND-RESISTANCE FACTOR DESIGN FOR BRIDGE COLUMNS
i
Compression members designed by LFD should have a maximum strength, kip (kN), T n
Pu 0.85As Fcr where As gross effective area of column cross section, in2 (mm2). For KLc /r √2 2E/Fy :
Fcr Fy 1
Fy 4 2E
KLr c
2
For KLc /r √2 2E/Fy : Fcr
2E 286,220 (KLc /r)2 (KLc /r)2
where Fcr buckling stress, ksi (MPa)
A F
Fy yield strength of the steel, ksi (MPa) K effective-length factor in plane of buckling Lc length of member between supports, in (mm) r radius of gyration in plane of buckling, in (mm) E modulus of elasticity of the steel, ksi (MPa) TLFeBOOK
A a s f m u (
40816_10_p321-354 p324
10/22/01
12:49 PM
Page 325
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p325
BRIDGE AND SUSPENSION-CABLE FORMULAS
325
The preceding equations can be simplified by introducing a Q factor: a
Q
KLr
2
c
Fy 2 2E
Then, the preceding equations can be rewritten as shown next: 2
For Q 1.0:
Fcr 1
Q 2
F
y
For Q 1.0: Fcr
Fy 2Q
ALLOWABLE-STRESS DESIGN FOR BRIDGE BEAMS
)
AASHTO gives the allowable unit (tensile) stress in bending as Fb 0.55Fy. The same stress is permitted for compression when the compression flange is supported laterally for its full length by embedment in concrete or by other means. When the compression flange is partly supported or unsupported in a bridge, the allowable bending stress, ksi (MPa), is (Table 10.2): TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 326
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p326
326
408
CHAPTER TEN
TABLE 10.2 Allowable Bending Stress in Braced Bridge Beams† Fy
Fb
36 (248) 50 (345)
20 (138) 27 (186)
†
Fb
Units in ksi (MPa).
I p h t l e s p
5 S10 C IL 7
b
yc
xc
√
0.772J 9.87 Iyc
Ld 0.55F 2
y
where L length, in (mm), of unsupported flange between connections of lateral supports, including knee braces Sxc section modulus, in3 (mm3), with respect to the compression flange Iyc moment of inertia, in4 (mm4) of the compression flange about the vertical axis in the plane of the web J 1/3(bc t3c bt t3c Dt3w)
w b d b
S
bc width, in (mm), of compression flange
T s
bt width, in (mm), of tension flange tc thickness, in (mm), of compression flange TLFeBOOK
40816_10_p321-354 p326
10/22/01
12:49 PM
Page 327
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p327
BRIDGE AND SUSPENSION-CABLE FORMULAS
327
tt thickness, in (mm), of tension flange tw thickness, in (mm), of web D depth, in (mm), of web d depth, in (mm), of flexural member In general, the moment-gradient factor Cb may be computed from the next equation. It should be taken as unity, however, for unbraced cantilevers and members in which the moment within a significant portion of the unbraced length is equal to, or greater than, the larger of the segment end moments. If cover plates are used, the allowable static stress at the point of cutoff should be computed from the preceding equation. The moment-gradient factor may be computed from n e
e
Cb 1.75 1.05
M1 0.3 M2
MM 2.3 1
2
2
where M1 smaller beam end moment, and M2 larger beam end moment. The algebraic sign of M1 /M2 is positive for double-curvature bending and negative for single-curvature bending.
STIFFENERS ON BRIDGE GIRDERS The minimum moment of inertia, in4 (mm4), of a transverse stiffener should be at least I ao t3J TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 328
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p328
328
408
CHAPTER TEN
where J 2.5h2/a2o 2 0.5 h clear distance between flanges, in (mm) w (
ao actual stiffener spacing, in (mm) t web thickness, in (mm) For paired stiffeners, the moment of inertia should be taken about the centerline of the web; for single stiffeners, about the face in contact with the web. The gross cross-sectional area of intermediate stiffeners should be at least
w c t
H
V A 0.15BDtw (1 C) 18t2w ! Vu where ! is the ratio of web-plate yield strength to stiffenerplate yield strength, B 1.0 for stiffener pairs, 1.8 for single angles, and 2.4 for single plates; and C is defined in the earlier section, “Allowable-Stress Design for Bridge Columns.” Vu should be computed from the previous section equations in “Shear Strength Design for Bridges.” The width of an intermediate transverse stiffener, plate, or outstanding leg of an angle should be at least 2 in (50.8 mm), plus 130 of the depth of the girder and preferably not less than 14 of the width of the flange. Minimum thickness is 116 of the width.
T w c t i s e b p
w Longitudinal Stiffeners These should be placed with the center of gravity of the fasteners h/5 from the toe, or inner face, of the compression flange. Moment of inertia, in4 (mm4), should be at least TLFeBOOK
40816_10_p321-354 p328
10/22/01
12:49 PM
Page 329
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p329
BRIDGE AND SUSPENSION-CABLE FORMULAS
I ht3 2.4
n t
329
a2o 0.13 h2
where ao actual distance between transverse stiffeners, in (mm); and t web thickness, in (mm). Thickness of stiffener, in (mm), should be at least b√fb /71.2, where b is the stiffener width, in (mm), and fb is the flange compressive bending stress, ksi (MPa). The bending stress in the stiffener should not exceed that allowable for the material.
s
HYBRID BRIDGE GIRDERS
r n e , 8 t s
These may have flanges with larger yield strength than the web and may be composite or noncomposite with a concrete slab, or they may utilize an orthotropic-plate deck as the top flange. Computation of bending stresses and allowable stresses is generally the same as that for girders with uniform yield strength. The bending stress in the web, however, may exceed the allowable bending stress if the computed flange bending stress does not exceed the allowable stress multiplied by R1
(1 )2 (3 ) 6 (3 )
where ratio of web yield strength to flange yield strength n
distance from outer edge of tension flange or bottom flange of orthotropic deck to neutral axis divided by depth of steel section TLFeBOOK
40816_10_p321-354 p332
10/22/01
12:49 PM
Page 333
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p333
BRIDGE AND SUSPENSION-CABLE FORMULAS
333
BRIDGE FASTENERS g o n d s e
For bridges, AASHTO specifies the working stresses for bolts. Bearing-type connections with high-strength bolts are limited to members in compression and secondary members. The allowable bearing stress is Fp 1.35Fu where Fp allowable bearing stress, ksi (MPa); and Fu tensile strength of the connected part, ksi (MPa) (or as limited by allowable bearing on the fasteners). The allowable bearing stress on A307 bolts is 20 ksi (137.8 MPa) and on structural-steel rivets is 40 ksi (275.6 MPa).
COMPOSITE CONSTRUCTION IN HIGHWAY BRIDGES
t
Shear connectors between a steel girder and a concrete slab in composite construction in a highway bridge should be capable of resisting both horizontal and vertical movement between the concrete and steel. Maximum spacing for shear connectors generally is 24 in (609.6 mm), but wider spacing may be used over interior supports, to avoid highly stressed portions of the tension flange (Fig. 10.1). Clear depth of concrete cover over shear connectors should be at least 2 in (50.8 mm), and they should extend at least 2 in (50.8 mm) above the bottom of the slab. TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 330
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p330
330
CHAPTER TEN
ratio of web area to area of tension flange or bottom flange of orthotropic-plate bridge
LOAD-FACTOR DESIGN FOR BRIDGE BEAMS For LFD of symmetrical beams, there are three general types of members to consider: compact, braced noncompact, and unbraced sections. The maximum strength of each (moment, inkip) (mmkN) depends on member dimensions and unbraced length, as well as on applied shear and axial load (Table 10.3). The maximum strengths given by the formulas in Table 10.3 apply only when the maximum axial stress does not exceed 0.15F y A, where A is the area of the member. Symbols used in Table 10.3 are defined as follows: Fy steel yield strength, ksi (MPa) Z plastic section modulus, in3 (mm3) S section modulus, in3 (mm3) b width of projection of flange, in (mm) d depth of section, in (mm) h unsupported distance between flanges, in (mm) M1 smaller moment, inkip (mmkN), at ends of unbraced length of member Mu Fy Z M1 /Mu is positive for single-curvature bending. TLFeBOOK
408
Web minimum thickness tu, in (mm)
Maximum unbraced length lb, in (mm)
Fy Z
b√Fy 65.0
d√Fy 608
[3600 2200(M1/Mu)]ry Fy
b√Fy 69.6
h 150
20,000 Af Fy d
Braced Fy S noncompact† Unbraced ________________________
See AASHTO specification ________________________
†
b 1064 d 9.35 tw tf √Fyf where Fyf is the yield strength of the flange, ksi (MPa); tw is the web thickness, in (mm); and tf flange thickness, in (mm).
TLFeBOOK
Page 331
Straight-line interpolation between compact and braced noncompact moments may be used for intermediate criteria, except that tw d√Fy /608 should be maintained as well as the following: For compact sections, when both b/tf and d/tw exceed 75% of the limits for these ratios, the following interaction equation applies:
12:49 PM
331
Flange minimum thickness tf, in (mm)
10/22/01
Compact†
Maximum bending strength Mu, inkip (mmkN)
40816_10_p321-354
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p331
Type of section
p330
r
l h s l
n s e s
TABLE 10.3 Design Criteria for Symmetrical Flexural Sections for Load-Factor Design of Bridges
40816_10_p321-354
10/22/01
12:49 PM
Page 332
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p332
332
408
CHAPTER TEN
BEARING ON MILLED SURFACES
B
For highway design, AASHTO limits the allowable bearing stress on milled stiffeners and other steel parts in contact to Fp 0.80Fu. Allowable bearing stresses on pins are given in Table 10.4. The allowable bearing stress for expansion rollers and rockers used in bridges depends on the yield point in tension Fy of the steel in the roller or the base, whichever is smaller. For diameters up to 25 in (635 mm) the allowable stress, kip/linear in (kN/mm), is
F b l b
w F l a o
Fy 13 0.6d p 20 For diameters from 25 to 125 in (635 to 3175 mm), p
Fy 13 3√d 20
C I
where d diameter of roller or rocker, in (mm).
TABLE 10.4 Allowable Bearing Stresses on Pins† Bridges
Fy
Buildings Fp 0.90Fy
Pins subject to rotation Fp 0.40Fy
Pins not subject to rotation Fp 0.80Fy
36 (248) 50 (344)
33 (227) 45 (310)
14 (96) 20 (137)
29 (199) 40 (225)
†
Units in ksi (MPa).
TLFeBOOK
S s s c s b t ( c s o
40816_10_p321-354 p332
10/22/01
12:49 PM
Page 333
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p333
BRIDGE AND SUSPENSION-CABLE FORMULAS
333
BRIDGE FASTENERS g o n d s e
For bridges, AASHTO specifies the working stresses for bolts. Bearing-type connections with high-strength bolts are limited to members in compression and secondary members. The allowable bearing stress is Fp 1.35Fu where Fp allowable bearing stress, ksi (MPa); and Fu tensile strength of the connected part, ksi (MPa) (or as limited by allowable bearing on the fasteners). The allowable bearing stress on A307 bolts is 20 ksi (137.8 MPa) and on structural-steel rivets is 40 ksi (275.6 MPa).
COMPOSITE CONSTRUCTION IN HIGHWAY BRIDGES
t
Shear connectors between a steel girder and a concrete slab in composite construction in a highway bridge should be capable of resisting both horizontal and vertical movement between the concrete and steel. Maximum spacing for shear connectors generally is 24 in (609.6 mm), but wider spacing may be used over interior supports, to avoid highly stressed portions of the tension flange (Fig. 10.1). Clear depth of concrete cover over shear connectors should be at least 2 in (50.8 mm), and they should extend at least 2 in (50.8 mm) above the bottom of the slab. TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 334
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p334
334
408
CHAPTER TEN
B I n i i s FIGURE 10.1 Maximum pitch for stud shear connectors in composite beams: 1 in (25.4 mm), 2 in (50.8 mm), 3 in (76.2 mm), and 24 in (609.6 mm).
Span/Depth Ratios
w
In bridges, for composite beams, preferably the ratio of span/steel beam depth should not exceed 30 and the ratio of span/depth of steel beam plus slab should not exceed 25. w
Effective Width of Slabs For a composite interior girder, the effective width assumed for the concrete flange should not exceed any of the following: 1. One-fourth the beam span between centers of supports 2. Distance between centerlines of adjacent girders 3. Twelve times the least thickness of the slab For a girder with the slab on only one side, the effective width of slab should not exceed any of the following: 1. One-twelfth the beam span between centers of supports 2. Half the distance to the centerline of the adjacent girder 3. Six times the least thickness of the slab TLFeBOOK
40816_10_p321-354 p334
10/22/01
12:49 PM
Page 335
40816 HICKS Mcghp Ch. 10 REVISE PASS rg 07/27/01 p335
335
BRIDGE AND SUSPENSION-CABLE FORMULAS
Bending Stresses In composite beams in bridges, stresses depend on whether or not the members are shored; they are determined as for beams in buildings (see “Composite Construction” in Chap. 9,“Building and Structures Formulas”), except that the stresses in the steel may not exceed 0.55Fy. (See the following equations.) e 6
For unshored members: fs
MD M L 0.55Fy Ss Str
where fy yield strength, ksi (MPa). f f
For shored members: fs
MD ML 0.55Fy Str
where fs stress in steel, ksi (MPa) d s
MD dead-load moment, in.kip (kN.mm) ML live-load moment, in.kip (kNmm) Ss section modulus of steel beam, in3 (mm3) Str section modulus of transformed composite section, in3 (mm3)
e s r
Vr shear range (difference between minimum and maximum shears at the point) due to live load and impact, kip (kN) Q static moment of transformed compressive concrete area about neutral axis of transformed section, in3 (mm3) TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 336
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p336
336
408
CHAPTER TEN
I moment of inertia of transformed section, in4 (mm4)
Shear Range
w
Shear connectors in bridges are designed for fatigue and then are checked for ultimate strength. The horizontal-shear range for fatigue is computed from Sr
VrQ I
where Sr horizontal-shear range at the juncture of slab and beam at point under consideration, kip/linear in (kN/linear mm). The transformed area is the actual concrete area divided by n (Table 10.5). The allowable range of horizontal shear Zr, kip (kN), for an individual connector is given by the next two equations, depending on the connector used.
d n o
TABLE 10.5 Ratio of Moduli of Elasticity of Steel and Concrete for Bridges fc for concrete 2.0–2.3 2.4–2.8 2.9–3.5 3.6–4.5 4.6–5.9 6.0 and over
n
w
Es Ec
N
11 10 9 8 7 6
T c
TLFeBOOK
40816_10_p321-354 p336
10/22/01
12:49 PM
Page 337
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p337
337
BRIDGE AND SUSPENSION-CABLE FORMULAS 4
For channels, with a minimum of 316-in (4.76-mm) fillet welds along heel and toe: Z r Bw
d r
where w channel length, in (mm), in transverse direction on girder flange; and B cyclic variable 4.0 for 100,000 cycles, 3.0 for 500,000 cycles, 2.4 for 2 million cycles, and 2.1 for over 2 million cycles. For welded studs (with height/diameter ratio H/d 4):
d r d r ,
Z r d 2 where d stud diameter, in (mm); and cyclic variable 13.0 for 100,000 cycles, 10.6 for 500,000 cycles, 7.85 for 2 million cycles, and 5.5 for over 2 million cycles. Required pitch of shear connectors is determined by dividing the allowable range of horizontal shear of all connectors at one section Zr, kip (kN), by the horizontal range of shear Sr, kip per linear in (kN per linear mm).
NUMBER OF CONNECTORS IN BRIDGES The ultimate strength of the shear connectors is checked by computation of the number of connectors required from N
P Su TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 338
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p338
338
408
CHAPTER TEN
where N number of shear connectors between maximum positive moment and end supports Su ultimate shear connector strength, kip (kN) [see Eqs. (10.1) and (10.2) that follow and AASHTO data] reduction factor 0.85
t
w t s
P force in slab, kip (kN) At points of maximum positive moments, P is the smaller of P1 and P2, computed from
U i F
P1 As Fy P2 0.85 fcAc w where Ac effective concrete area, in (mm ) 2
2
fc 28-day compressive strength of concrete, ksi (MPa) As total area of steel section, in2 (mm2) Fy steel yield strength, ksi (MPa) The number of connectors required between points of maximum positive moment and points of adjacent maximum negative moment should equal or exceed N2, given by N2
P P3 Su
A F B a
TLFeBOOK
40816_10_p321-354 p338
10/22/01
12:49 PM
Page 339
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p339
339
BRIDGE AND SUSPENSION-CABLE FORMULAS
-
At points of maximum negative moments, the force in the slab P3, is computed from
) d
P3 AsrFyr where Asr area of longitudinal reinforcing within effective flange, in2 (mm2); and Fyr reinforcing steel yield strength, ksi (MPa).
e
Ultimate Shear Strength of Connectors in Bridges For channels:
Su 17.4 h
t 2
w √f c
(10.1)
where h average channel-flange thickness, in (mm) t channel-web thickness, in (mm) ,
w channel length, in (mm) For welded studs (H/d 4 in (101.6 mm): Su 0.4d 2 √fcEc
f n
(10.2)
ALLOWABLE-STRESS DESIGN FOR SHEAR IN BRIDGES Based on the AASHTO specification for highway bridges, the allowable shear stress, ksi (MPa), may be computed from TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 340
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p340
340
408
CHAPTER TEN
Fv
Fy Fy C 3 3
for flexural members with unstiffened webs with h/tw 150 or for girders with stiffened webs with a/h exceeding 3 and 67,600(h/tw)2: C 1.0
h/t w
45,000k Fy (h/t w)2
k 5 if
h tw
when when
when
S
h 1.25 tw
P
a exceeds 3 or 67,600 h
190
5 (a/h)2
√
th
S t d f
2
w
otherwise w
k Fy
For girders with transverse stiffeners and a/h less than 3 and 67,600(h/tw)2, the allowable shear stress is given by Fv
Fy 3
T w b d
h 1.25 tw
or stiffeners are not required 5
M F H
C 1.15 √11 C(a/h) 2
Stiffeners are required when the shear exceeds Fv. TLFeBOOK
40816_10_p321-354 p340
10/22/01
12:49 PM
Page 341
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p341
341
BRIDGE AND SUSPENSION-CABLE FORMULAS
MAXIMUM WIDTH/THICKNESS RATIOS FOR COMPRESSION ELEMENTS FOR HIGHWAY BRIDGES 0 d
Table 10.6 gives a number of formulas for maximum width/thickness ratios for compression elements for highway bridges. These formulas are valuable for highway bridge design.
SUSPENSION CABLES Parabolic Cable Tension and Length Steel cables are often used in suspension bridges to support the horizontal roadway load (Fig. 10.2). With a uniformly distributed load along the horizontal, the cable assumes the form of a parabolic arc. Then, the tension at midspan is H
wL2 8d
where H midspan tension, kip (N) w load on a unit horizontal distance, klf (kN/m) n y
L span, ft (m) d sag, ft (m) The tension at the supports of the cable is given by
T H2
wL2
2 0.5
TLFeBOOK
Load-and-resistance-factor designc Description of element
342
Webs in flexural compression
Noncompactd
65
70 e
√Fy
√Fy
608
150
√Fy
fa 0.44Fy Description of element
Fy 36 ksi (248 MPa)
Fy 50 ksi (344.5 MPa)
51 √fa 12
12
11
Plates supported in one side and outstanding legs of angles In main members
TLFeBOOK
Page 342
fa 0.44Fy
12:49 PM
Allowable-stress design f
10/22/01
Flange projection of rolled or fabricated I-shaped beams
Compact
40816_10_p321-354
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p342
TABLE 10.6 Maximum Width/Thickness Ratios b /t a for Compression Elements for Highway Bridgesb
408
p342
Plates supported on two edges or webs of box shapesg
126 √fa 45
32
27
Solid cover plates supported on two edges or solid websh
158 √fa 50
40
34
Perforated cover plates supported on two edges for box shapes
190 √fa 55
48
41
TLFeBOOK
Page 343
b width of element or projection; t thickness. The point of support is the inner line of fasteners or fillet welds connecting a plate to the main segment or the root of the flange of rolled shapes. In LRFD, for webs of compact sections, b d, the beam depth; and for noncompact sections, b D, the unsupported distance between flange components. b As required in AASHTO “Standard Specification for Highway Bridges.” The specifications also provide special limitations on plate-girder elements. c Fy specified minimum yield stress, ksi (MPa), of the steel. d Elements with width/thickness ratios that exceed the noncompact limits should be designed as slender elements. e When the maximum bending moment M is less than the bending strength Mu, b/t in the table may be multiplied by √Mu /M . f fa computed axial compression stress, ksi (MPa). g For box shapes consisting of main plates, rolled sections, or component segments with cover plates. h For webs connecting main members or segments for H or box shapes. a
12:49 PM
11
10/22/01
12
40816_10_p321-354
51 √fa 16
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p343
343
In bracing and other secondary members
40816_10_p321-354
10/22/01
12:49 PM
Page 344
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p344
344
408
CHAPTER TEN
T
S
FIGURE 10.2 the horizontal.
Cable supporting load uniformly distributed along
where T tension at supports, kip (N); and other symbols are as before. Length of the cable, S, when d/L is 1/20, or less, can be approximated from SL
8d 2 3L
G S C F l m a
where S cable length, ft (m). T Catenary Cable Sag and Distance between Supports
T
A cable of uniform cross section carrying only its own weight assumes the form of a catenary. By using the same previous notation, the catenary parameter, c, is found from TLFeBOOK
40816_10_p321-354 p344
10/22/01
12:49 PM
Page 345
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p345
345
BRIDGE AND SUSPENSION-CABLE FORMULAS
dc
T w
Then
S2
2 0.5
c (d c)2
Sag d c ft (m) Span length then is L 2c, with the previous same symbols.
g
s e
GENERAL RELATIONS FOR SUSPENSION CABLES Catenary For any simple cable (Fig. 10.3) with a load of qo per unit length of cable, kip/ft (N/m), the catenary length s, ft (m), measured from the low point of the cable is, with symbols as given in Fig. 10.3, ft (m), s
q x 1 H sinh o x qo H 3!
qH x o
2
3
Tension at any point is T √H 2 q2o s2 H qoy The distance from the low point C to the left support is n e m
a
H cosh1 qo
qH f o
L
1
TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 346
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p346
346
408
CHAPTER TEN
b s
P FIGURE 10.3 Simple cables. (a) Shape of cable with concentrated load; (b) shape of cable with supports at different levels.
where fL vertical distance from C to L, ft (m). The distance from C to the right support R is b
H cosh1 qo
qH f o
R
1 p
1
where fR vertical distance from C to R. Given the sags of a catenary fL and fR under a distributed vertical load qo, the horizontal component of cable tension H may be computed from qo l cosh1 H
qHf
o L
U l d t a
1 cosh1
qHf
o R
1
T
w L
where l span, or horizontal distance between supports L and R a b. This equation usually is solved by trial. A first estimate of H for substitution in the right-hand side of the equation may be obtained by approximating the catenary TLFeBOOK
R
40816_10_p321-354 p346
10/22/01
12:49 PM
Page 347
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p347
BRIDGE AND SUSPENSION-CABLE FORMULAS
347
by a parabola. Vertical components of the reactions at the supports can be computed from RL H sinh
qo a H
RR H sinh
qo b H
Parabola -
-
Uniform vertical live loads and uniform vertical dead loads other than cable weight generally may be treated as distributed uniformly over the horizontal projection of the cable. Under such loadings, a cable takes the shape of a parabola. Take the origin of coordinates at the low point C (Fig. 10.3). If wo is the load per foot (per meter) horizontally, the parabolic equation for the cable slope is y
d n
L . f y
wo x 2 2H
The distance from the low point C to the left support L is a
Hh l 2 wo l
where l span, or horizontal distance between supports L and R a b; h vertical distance between supports. The distance from the low point C to the right support R is b
1 Hh 2 wo l TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 348
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p348
348
408
CHAPTER TEN
T
Supports at Different Levels The horizontal component of cable tension H may be computed from
L H
wo l h2
2
f
R
h w l √fL fR o 2 8f
2
where fL vertical distance from C to L fR vertical distance from C to R f sag of cable measured vertically from chord LR midway between supports (at x Hh/wol)
L
As indicated in Fig. 10.3b: f fL
h yM 2
where yM Hh2/2wo l 2. The minus sign should be used when low point C is between supports. If the vertex of the parabola is not between L and R, the plus sign should be used. The vertical components of the reactions at the supports can be computed from
VL wo a
wol Hh 2 l
Vr wo b
wol Hh 2 l
S I z f
T
TLFeBOOK
40816_10_p321-354 p348
10/22/01
12:49 PM
Page 349
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p349
BRIDGE AND SUSPENSION-CABLE FORMULAS
349
Tension at any point is T √H 2 wo2 x 2
-
Length of parabolic arc RC is LRC
b 2
√ wob H
1
b
1 6
2
H wb sinh o 2wo H
wH b o
2
3
Length of parabolic arc LC is ) LLC
a 2
√
a d e e s
1
1 6
wHa 2wH 2
o
sinh o
wo a H
wH a o
2
3
Supports at Same Level In this case, fL fR f, h 0, and a b l/2. The horizontal component of cable tension H may be computed from H
wo l 2 8f
The vertical components of the reactions at the supports are VL VR
wo l 2 TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 350
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p350
350
408
CHAPTER TEN
Maximum tension occurs at the supports and equals TL TR
wo l 2
√
1
I e f
l 16 f 2 2
Length of cable between supports is L
1 2
√
1
l 1
w2Hl wH o
2
sinh
o
wo l 2H
i
8 f 32 f 256 f 3 l2 5 l4 7 l6 2
4
6
If additional uniformly distributed load is applied to a parabolic cable, the change in sag is approximately f
15 l L 16 f 5 24 f 2/l 2
w d p t
For a rise in temperature t, the change in sag is about f
l 2ct 15 8 f2 1 2 2 16 f (5 24 f /l ) 3 l2
w
where c coefficient of thermal expansion. Elastic elongation of a parabolic cable is approximately L
Hl AE
1 163 lf 2
2
where A cross-sectional area of cable
S
E modulus of elasticity of cable steel H horizontal component of tension in cable TLFeBOOK
40816_10_p321-354 p350
10/22/01
12:49 PM
Page 351
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p351
351
BRIDGE AND SUSPENSION-CABLE FORMULAS
If the corresponding change in sag is small, so that the effect on H is negligible, this change may be computed from f
15 Hl2 1 16 f 2/3l 2 16 AEf 5 24 f 2/l 2
For the general case of vertical dead load on a cable, the initial shape of the cable is given by yD -
MD HD
where MD dead-load bending moment that would be produced by load in a simple beam; and HD horizontal component of tension due to dead load. For the general case of vertical live load on the cable, the final shape of the cable is given by yD
MD ML HD HL
where vertical deflection of cable due to live load y
ML live-load bending moment that would be produced by live load in simple beam HL increment in horizontal component of tension due to live load Subtraction yields
ML HL yD HD HL TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 352
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p352
352
408
CHAPTER TEN
If the cable is assumed to take a parabolic shape, a close approximation to HL may be obtained from
w HL K D AE HD Kl
1
dx
0
1 2
1
dx
0
14 52 16l f √1 16l f
2
2
3l loge 32 f
2
2
4l f √1 16l f 2
2
where d 2/dx2. If elastic elongation and can be ignored,
1
HL
ML dx
0 1
yD dx
3 2 fl
C T c e v l q l u i v b
1
ML dx
w
0
0
Thus, for a load uniformly distributed horizontally wL,
1
0
ML dx
wL l 3 12
and the increase in the horizontal component of tension due to live load is HL
w l2 w l 2 8HD 3 wL l 3 L L 2 f l 12 8f 8 wDl 2 F c c
wL H wD D TLFeBOOK
40816_10_p321-354 p352
10/22/01
12:49 PM
Page 353
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p353
BRIDGE AND SUSPENSION-CABLE FORMULAS
e
353
CABLE SYSTEMS The cable that is concave downward (Fig. 10.4) usually is considered the load-carrying cable. If prestress in that cable exceeds that in the other cable, the natural frequencies of vibration of both cables always differ for any value of live load. To avoid resonance, the difference between the frequencies of the cables should increase with increase in load. Thus, the two cables tend to assume different shapes under specific dynamic loads. As a consequence, the resulting flow of energy from one cable to the other dampens the vibrations of both cables. Natural frequency, cycles per second, of each cable may be estimated from n
n l
√
Tg w
where n integer, 1 for fundamental mode of vibration, 2 for second mode, . . . l span of cable, ft (m) w load on cable, kip/ft (kN/m)
e
FIGURE 10.4 Planar cable systems: (a) completely separated cables; (b) cables intersecting at midspan; (c) crossing cables; (d) cables meeting at supports. TLFeBOOK
40816_10_p321-354
10/22/01
12:49 PM
Page 354
40816 HICKS Mcghp Ch. 10 REVISE PASS bzm 6/7/01 p354
354
CHAPTER TEN
g acceleration due to gravity 32.2 ft/s2 T cable tension, kip (N) The spreaders of a cable truss impose the condition that under a given load the change in sag of the cables must be equal. Nevertheless, the changes in tension of the two cables may not be equal. If the ratio of sag to span f /l is small (less than about 0.1), for a parabolic cable, the change in tension is given approximately by H
16 AEf f 3 l2
where f change in sag A cross-sectional area of cable E modulus of elasticity of cable steel
TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 355
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p355
CHAPTER 11
HIGHWAY AND ROAD FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_11_p355-380
10/22/01
12:50 PM
Page 356
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p356
356
4081
CHAPTER ELEVEN
CIRCULAR CURVES Circular curves are the most common type of horizontal curve used to connect intersecting tangent (or straight) sections of highways or railroads. In most countries, two methods of defining circular curves are in use: the first, in general use in railroad work, defines the degree of curve as the central angle subtended by a chord of 100 ft (30.48 m) in length; the second, used in highway work, defines the degree of curve as the central angle subtended by an arc of 100 ft (30.48 m) in length. The terms and symbols generally used in reference to circular curves are listed next and shown in Figs. 11.1 and 11.2. F
FIGURE 11.1
Circular curve.
TLFeBOOK
40816_11_p355-380 p356
10/22/01
12:50 PM
Page 357
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p357
HIGHWAY AND ROAD FORMULAS
357
l ) o , e f y e o d FIGURE 11.2
PC PI PT R D I
T L C E
Offsets to circular curve.
point of curvature, beginning of curve point of intersection of tangents point of tangency, end of curve radius of curve, ft (m) degree of curve (see previous text) deflection angle between tangents at PI, also central angle of curve tangent distance, distance from PI to PC or PT, ft (m) length of curve from PC to PT measured on 100-ft (30.48-m) chord for chord definition, on arc for arc definition, ft (m) length of long chord from PC to PT, ft (m) external distance, distance from PI to midpoint of curve, ft (m) TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 358
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p358
358
4081
CHAPTER ELEVEN
M midordinate, distance from midpoint of curve to midpoint of long chord, ft (m) d central angle for portion of curve (d D) l length of curve (arc) determined by central angle d, ft (m) c length of curve (chord) determined by central angle d, ft (m) a tangent offset for chord of length c, ft (m) b chord offset for chord of length c, ft (m) Equations of Circular Curves R
5,729.578 D
exact for arc definition, approximate for chord definition
50 sin 12 D
exact for chord definition
T R tan 12 I
exact
M R vers 12 I R (1 cos 12 I)
exact
C 2R sin 2 I
exact
100I D
exact
1
L LC d
C3 L3 2 24R 24R 2 Dl 100
P w b t e F
exact
E R exsec 12 I R (sec 12 I 1)
P
approximate
exact for arc definition TLFeBOOK
40816_11_p355-380 p358
10/22/01
12:50 PM
Page 359
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p359
HIGHWAY AND ROAD FORMULAS
e
sin
Dc 100
d c z 2R
359
approximate for chord definition exact for chord definition
a
c2 2R
approximate
b
c2 R
approximate
PARABOLIC CURVES Parabolic curves are used to connect sections of highways or railroads of differing gradient. The use of a parabolic curve provides a gradual change in direction along the curve. The terms and symbols generally used in reference to parabolic curves are listed next and are shown in Fig. 11.3. PVC point of vertical curvature, beginning of curve PVI point of vertical intersection of grades on either side of curve PVT point of vertical tangency, end of curve G1 grade at beginning of curve, ft/ft (m/m) G2 grade at end of curve, ft/ft (m/m) L length of curve, ft (m) R rate of change of grade, ft/ft2 (m/m2) V elevation of PVI, ft (m) TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 360
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p360
360
4081
CHAPTER ELEVEN
FIGURE 11.3
h
Vertical parabolic curve (summit curve).
E0 elevation of PVC, ft (m) Et elevation of PVT, ft (m) x distance of any point on the curve from the PVC, ft (m) Ex elevation of point x distant from PVC, ft (m) xs distance from PVC to lowest point on a sag curve or highest point on a summit curve, ft (m) Es elevation of lowest point on a sag curve or highest point on a summit curve, ft (m)
H F m c
Equations of Parabolic Curves
r w t o e
In the parabolic-curve equations given next, algebraic quantities should always be used. Upward grades are positive and downward grades are negative.
e S c
TLFeBOOK
40816_11_p355-380 p360
10/22/01
12:50 PM
Page 361
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p361
361
HIGHWAY AND ROAD FORMULAS
R
G2 G1 L
E 0 V 12 LG1 E x E 0 G1x 12 Rx 2 xs
G1 R
Es E0
G21 2R
Note. If xs is negative or if xs L, the curve does not have a high point or a low point.
HIGHWAY CURVES AND DRIVER SAFETY
e
For the safety and comfort of drivers, provision usually is made for gradual change from a tangent to the start of a circular curve. As indicated in Fig. 11.4, typically the outer edge is raised first until the outer half of the cross section is level with the crown (point B). Then, the outer edge is raised farther until the cross section is straight (point C). From there on, the entire cross section is rotated until the full superelevation is attained (point E). Superelevated roadway cross sections are typically employed on curves of rural highways and urban freeways. Superelevation is rarely used on local streets in residential, commercial, or industrial areas. TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 362
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p362
362
4081
CHAPTER ELEVEN
( o a a
S FIGURE 11.4 Superelevation variations along a spiral transition curve.
HIGHWAY ALIGNMENTS Geometric design of a highway is concerned with horizontal and vertical alignment as well as the cross-sectional elements. Horizontal alignment of a highway defines its location and orientation in plan view. Vertical alignment of a highway deals with its shape in profile. For a roadway with contiguous travel lanes, alignment can be conveniently represented by the centerline of the roadway.
T a a t w p r p v m r
Stationing Distance along a horizontal alignment is measured in terms of stations. A full station is defined as 100 ft (30.48 m) and a half station as 50 ft (15.24 m). Station 100 50 is 150 ft (45.7 m) from the start of the alignment, station 0 00. A point 1492.27 ft (454.84 m) from 0 00 is denoted as 14 92.27, indicating a location 14 stations, 1400 ft TLFeBOOK
F
40816_11_p355-380 p362
10/22/01
12:50 PM
Page 363
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p363
363
HIGHWAY AND ROAD FORMULAS
(426.72 m) plus 92.27 ft (28.12 m), from the starting point of the alignment. This distance is measured horizontally along the centerline of the roadway, whether it is a tangent, a curve, or a combination of these.
Stopping Sight Distance .
l n y d
s d t . s t
This is the length of roadway needed between a vehicle and an arbitrary object (at some point down the road) to permit a driver to stop a vehicle safely before reaching the obstruction. This is not to be confused with passing sight distance, which American Association of State Highway and Transportation Officials (AASHTO) defines as the “length of roadway ahead visible to the driver.” Figure 11.5 shows the parameters governing stopping sight distance on a crest vertical curve. For crest vertical curves, AASHTO defines the minimum length Lmin, ft (m), of crest vertical curves based on a required sight distance S, ft (m), as that given by
FIGURE 11.5
Stopping sight distance on a crest vertical curve.
TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 364
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p364
364
4081
CHAPTER ELEVEN
Lmin
AS2
SL
100 √2H1 √2H2
2
When eye height is 3.5 ft (1.07 m) and object height is 0.5 ft (0.152 m): Lmin
AS2 SL 1329
w e t t a a a c
Also, for crest vertical curves: 200 √H1 √H2 L min 25 AS 2
S F
2
S L
When eye height is 3.5 ft (1.07 m) and object height 0.5 ft (0.152 m): Lmin 25
1329 S L AS2
T e l o a I d
where A algebraic difference in grades, percent, of the tangents to the vertical curve H1 eye height, ft (m), above the pavement
w
H2 object height, ft (m), above the pavement Design controls for vertical curves can be established in terms of the rate of vertical curvature K defined by K
L A TLFeBOOK
40816_11_p355-380 p364
10/22/01
12:50 PM
Page 365
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p365
365
HIGHWAY AND ROAD FORMULAS
t
where L length, ft (m), of vertical curve and A is defined earlier. K is useful in determining the minimum sight distance, the length of a vertical curve from the PVC to the turning point (maximum point on a crest and minimum on a sag). This distance is found by multiplying K by the approach gradient. Recommended values of K for various design velocities and stopping sight distances for crest and sag vertical curves are published by AASHTO.
STRUCTURAL NUMBERS FOR FLEXIBLE PAVEMENTS
t
The design of a flexible pavement or surface treatment expected to carry more than 50,000 repetitions of equivalent single 18-kip axle load (SAI) requires identification of a structural number SN that is used as a measure of the ability of the pavement to withstand anticipated axle loads. In the AASHTO design method, the structural number is defined by
e
SN SN1 SN2 SN3 where
n
SN1 structural number for the surface course a1 D1 a1 layer coefficient for the surface course D1 actual thickness of the surface course, in (mm) SN2 structural number for the base course a2 D2 m2 TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 366
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p366
366
4081
CHAPTER ELEVEN
a2 layer coefficient for the base course D2 actual thickness of the base course, in (mm) m2 drainage coefficient for the base course SN3 structural number for the subbase course a3 D3 m3 a3 layer coefficient for the subbase course D3 actual thickness of the subbase course, in (mm) m3 drainage coefficient for the subbase The layer coefficients an are assigned to materials used in each layer to convert structural numbers to actual thickness. They are a measure of the relative ability of the materials to function as a structural component of the pavement. Many transportation agencies have their own values for these coefficients. As a guide, the layer coefficients may be 0.44 for asphaltic-concrete surface course, 0.14 for
FIGURE 11.6
Typical two-lane highway with linear cross slopes.
TLFeBOOK
F h m d
40816_11_p355-380 p366
10/22/01
12:50 PM
Page 367
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p367
HIGHWAY AND ROAD FORMULAS
367
)
e
n
d . r y r
FIGURE 11.7 Types of interchanges for intersecting grade-separated highways. (a) T or trumpet; (b) Y or delta; (c) one quadrant; (d) diamond; (e) full cloverleaf; (f) partial cloverleaf; (g) semidirect; (h) alldirectional four leg.
TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 368
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p368
368
4081
CHAPTER ELEVEN
F s r
c b n a p t c FIGURE 11.8 Highway turning lanes. (a) Unchannelized; (b) channelized; (c) flared.
TLFeBOOK
i c s p
40816_11_p355-380 p368
10/22/01
12:50 PM
Page 369
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p369
HIGHWAY AND ROAD FORMULAS
369
FIGURE 11.9 Highway turning lanes. (a) Unchannelized; (b) intersection with a right-turn lane; (c) intersection with a single-turning roadway; (d) channelized intersection with a pair of turning roadways.
;
crushed-stone base course, and 0.11 for sandy-gravel subbase course. The thicknesses D1, D2, and D3 should be rounded to the nearest 12 in (12.7 mm). Selection of layer thicknesses usually is based on agency standards, maintainability of the pavement, and economic feasibility. Figure 11.6 shows the linear cross slopes for a typical two-lane highway. Figure 11.7 shows the use of circular curves in a variety intersecting grade-separated highways. Figure 11.8 shows the use of curves in at-grade four-leg intersections of highways. Figure 11.9 shows the use of curves in at-grade T (three-leg) intersections. Figure 11.10 shows street space and maneuvering space used for various parking positions. TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 370
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p370
370
4081
CHAPTER ELEVEN
p
w
FIGURE 11.10 Street space and maneuvering space used for various parking positions. USCS (SI) equivalent units in ft (m): 7 (2.13), 17 (5.18), 18 (5.49), 19 (5.79), 22 (6.7), 29 (8.84), 36 (10.97), 40 (12.19).
A i ( p r r
D TRANSITION (SPIRAL) CURVES On starting around a horizontal circular curve, a vehicle and its contents are immediately subjected to centrifugal forces. The faster the vehicle enters the circle and the sharper the curvature is, the greater the influence on vehicles and drivers of the change from tangent to curve. When transition curves are not provided, drivers tend to create their own transition curves by moving laterally within their travel lane and sometimes the adjoining lane, a hazardous maneuver. TLFeBOOK
A w r b l s t b
40816_11_p355-380 p370
10/22/01
12:50 PM
Page 371
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p371
HIGHWAY AND ROAD FORMULAS
371
The minimum length L, ft (m), of a spiral may be computed from L
3.15V 3 RC
where V vehicle velocity, mi/h (km/h) R radius, ft (m), of the circular curve to which the spiral is joined C rate of increase of radial acceleration
s 7 .
An empirical value indicative of the comfort and safety involved, C values often used for highways range from 1 to 3. (For railroads, C is often taken as unity 1.) Another, more practical, method for calculating the minimum length of spiral required for use with circular curves is to base it on the required length for superelevation runoff.
DESIGNING HIGHWAY CULVERTS
e l e n e r s
A highway culvert is a pipelike drainage facility that allows water to flow under the road without impeding traffic. Corrugated and spiral steel pipe are popular for culverts because they can be installed quickly, have long life, are low in cost, and require little maintenance. With corrugated steel pipe, the seam strength must be adequate to withstand the ring-compression thrust from the total load supported by the pipe. This thrust C, lb/ft (N/m), of structure is C (LL DL)
S 2 TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 372
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p372
372
4081
CHAPTER ELEVEN
where LL live-load pressure, lb/ft2 (N/m2) DL dead-load pressure, lb/ft2 (N/m2) S span (or diameter), ft (m) Handling and installation strength must be adequate to withstand shipping and placing of the pipe in the desired position at the highway job site. The handling strength is measured by a flexibility factor determined from FF
D2 EI
o t f p z
where D pipe diameter or maximum span, in (mm) E modulus of elasticity of the pipe material, lb/in2 (MPa) I moment of inertia per unit length of cross section of the pipe wall, in4/in (mm4/mm) The ring-compression stress at which buckling becomes critical in the interaction zone for diameters less then 126.5r/K is f c 45,000 1.406
KDr
2
For diameters greater than 126.5r /K: fc
12E (KD/r) 2
where fc buckling stress, lb/in2 (MPa) K soil stiffness factor TLFeBOOK
w
40816_11_p355-380 p372
10/22/01
12:50 PM
Page 373
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p373
HIGHWAY AND ROAD FORMULAS
373
D pipe diameter or span, in (mm) r radius of gyration of pipe wall, in4/in (mm4/mm)
o d s
2
E modulus of elasticity of pipe material, lb/in2 (MPa) Note. For excellent sidefill, compacted 90 to 95 percent of standard density, K 0.22; for good sidefill, compacted to 85 percent of standard density, K 0.44. Conduit deflection is given by the Iowa formula. This formula gives the relative influence on the deflection of the pipe strength and the passive side pressure resisting horizontal movement of the pipe wall, or x
D1 KWc r 3 EI 0.061Er 3
where x horizontal deflection of pipe, in (mm) D1 deflection lag factor s n
K bedding constant (dependent on bedding angle) Wc vertical load per unit length of pipe, lb per linear in (N/mm) r mean radius of pipe, in (mm) E modulus of elasticity of pipe material, lb/in2 (MPa) I moment of inertia per unit length of cross section of pipe wall, in4/in (mm4/mm) E modulus of passive resistance of enveloping soil, lb/in2 (MPa) TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 374
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p374
374
4081
CHAPTER ELEVEN
Soil modulus E has not been correlated with the types of backfill and compaction. This limits the usefulness of the formula to analysis of installed structures that are under observation.
AMERICAN IRON AND STEEL INSTITUTE (AISI) DESIGN PROCEDURE The design procedure for corrugated steel structures recommended in their Handbook of Steel Drainage and Highway Construction Projects is given below.
Backfill Density Select a percentage of compaction of pipe backfill for design. The value chosen should reflect the importance and size of the structure and the quality that can reasonably be expected. The recommended value for routine use is 85 percent. This value usually applies to ordinary installations for which most specifications call for compaction to 90 percent. However, for more important structures in higher fill situations, consideration must be given to selecting higher quality backfill and requiring this quality for construction.
Design Pressure When the height of cover is equal to, or greater than, the span or diameter of the structure, enter the load-factor chart (Fig. 11.11) to determine the percentage of the total load acting on the steel. For routine use, the 85 percent soil compaction provides a load factor K 0.86. The total load is TLFeBOOK
F f
m t e T
W p
40816_11_p355-380 p374
10/22/01
12:50 PM
Page 375
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p375
HIGHWAY AND ROAD FORMULAS
375
s e r
y
r d e r l r .
e t d s
FIGURE 11.11 Load factors for corrugated steel pipe are plotted as a function of specified compaction of backfill.
multiplied by K to obtain the design pressure P acting on the steel. If the height of cover is less than one pipe diameter, the total load TL is assumed to act on the pipe, and TL Pv; that is, Pv DL LL I
HS
When the height of cover is equal to, or greater than, one pipe diameter, Pv K(DL LL I)
HS TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 376
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p376
376
4081
CHAPTER ELEVEN
where Pv design pressure, kip/ft2 (MPa/m2) K load factor DL dead load, kip/ft2 (MPa/m2) LL live load, kip/ft2 (MPa/m2) I impact, kip/ft2 (MPa/m2) H height of cover, ft (m) S span or pipe diameter, ft (m)
Ring Compression The compressive thrust C, kip/ft (MPa/m), on the conduit wall equals the radial pressure Pv , kip/ft2 (MPa/m2), acting on the wall multiplied by the wall radius R, ft (m); or C Pv R. This thrust, called ring compression, is the force carried by the steel. The ring compression is an axial load acting tangentially to the conduit wall (Fig. 11.12). For conventional structures in which the top arc approaches a semicircle, it is convenient to substitute half the span for the wall radius. Then, S C Pv 2
F i
a t r ( s b
W k
Allowable Wall Stress The ultimate compression in the pipe wall is expressed by Eqs. (11.1) and (11.2) that follow. The ultimate wall stress is equal to the specified minimum yield point of the steel TLFeBOOK
40816_11_p355-380 p376
10/22/01
12:50 PM
Page 377
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p377
HIGHWAY AND ROAD FORMULAS
t g r e d r a r
377
FIGURE 11.12 Radial pressure, Pv, on the wall of a curved conduit is resisted by compressive thrust C.
and applies to the zone of wall crushing or yielding. Equation (11.1) applies to the interaction zone of yielding and ring buckling; Eq. (11.2) applies to the ring-buckling zone. When the ratio D/r of pipe diameter—or span D, in (mm), to radius of gyration r, in (mm), of the pipe cross section—does not exceed 294, the ultimate wall stress may be taken as equal to the steel yield strength: Fb Fy 33 ksi (227.4 MPa) When D/r exceeds 294 but not 500, the ultimate wall stress, ksi (MPa), is given by
y s l
Fb 40 0.000081
Dr
2
(11.1) TLFeBOOK
40816_11_p355-380
10/22/01
12:50 PM
Page 378
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p378
378
4081
CHAPTER ELEVEN
When D/r is more than 500, Fb
4.93 10 (D/r) 2
6
(11.2)
A safety factor of 2 is applied to the ultimate wall stress to obtain the design stress Fc, ksi (MPa): Fc
Fb 2
w 3 w e
(11.3)
Wall Thickness Required wall area A, in2/ft (mm2/m), of width, is computed from the calculated compression C in the pipe wall and the allowable stress Fc: A
C Fc
(11.4)
From the AISI table for underground conduits, select the wall thickness that provides the required area with the same corrugation used for selection of the allowable stress.
e c e i o t a s a
C Check Handling Stiffness Minimum pipe stiffness requirements for practical handling and installation, without undue care or bracing, have been established through experience. The resulting flexibility factor FF limits the size of each combination of corrugation pitch and metal thickness: FF
D2 EI
(11.5) TLFeBOOK
S d k e u f d
40816_11_p355-380 p378
10/22/01
12:50 PM
Page 379
40816 HICKS Mcghp Ch. 11 REVISE PASS bzm 6/7/01 p379
HIGHWAY AND ROAD FORMULAS
) s
)
d e
) e e
379
where E modulus of elasticity, ksi (MPa), of steel 30,000 ksi (206,850 MPa); and I moment of inertia of wall, in4/in (mm4/mm). The following maximum values of FF are recommended for ordinary installations: FF 0.0433 for factory-made pipe with less than a 120-in (30.48-cm) diameter and with riveted, welded, or helical seams FF 0.0200 for field-assembled pipe with over a 120-in (30.48-cm) diameter or with bolted seams Higher values can be used with special care or where experience indicates. Trench condition, as in sewer design, can be one such case; use of aluminum pipe is another. For example, the flexibility factor permitted for aluminum pipe in some national specifications is more than twice that recommended here for steel because aluminum has only onethird the stiffness of steel, the modulus for aluminum being about 10,000 vs. 30,000 ksi (68,950 vs. 206,850 MPa) for steel. Where a high degree of flexibility is acceptable for aluminum, it is equally acceptable for steel.
Check Bolted Seams g n y n
Standard factory-made pipe seams are satisfactory for all designs within the maximum allowable wall stress of 16.5 ksi (113.8 MPa). Seams bolted in the shop or field, however, continue to be evaluated on the basis of test values for uncurved, unsupported columns. A bolted seam (standard for structural plate) must have a test strength of twice the design load in the pipe wall.
) TLFeBOOK
This page intentionally left blank.
TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 381
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p381
CHAPTER 12
HYDRAULICS AND WATERWORKS FORMULAS
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_12a_p381-431
10/22/01
12:51 PM
Page 382
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p382
382
CHAPTER TWELVE
To simplify using the formulas in this chapter, Table 12.1 presents symbols, nomenclature, and United States Customary System (USCS) and System International (SI) units found in each expression.
CAPILLARY ACTION Capillarity is due to both the cohesive forces between liquid molecules and adhesive forces of liquid molecules. It shows up as the difference in liquid surface elevations between the inside and outside of a small tube that has one end submerged in the liquid (Fig. 12.1). Capillarity is commonly expressed as the height of this rise. In equation form, h
2 cos (w1 w2)r
where h capillary rise, ft (m) surface tension, lb/ft (N/m) w1 and w2 specific weights of fluids below and above meniscus, respectively, lb/ft (N/m) angle of contact r radius of capillary tube, ft (m) Capillarity, like surface tension, decreases with increasing temperature. Its temperature variation, however, is small and insignificant in most problems. TLFeBOOK
4081
mm2 m0.5/s m0.37/s m m m MPa N m/s2 m m m m Ns2/m s/m1/3 m N MPa TLFeBOOK
Page 383
SI units
ft2 ft5/s ft0.37/s ft ft ft lb/in2 lb ft/s2 ft ft ft ft lbs2/ft s/ft1/3 ft lb psf
12:51 PM
USCS units
L2 L1/2/T L0.37/T L L L F/L2 F L/T 2 L L L L FT 2/L T/L1/3 L F F/L2
10/22/01
Dimensions
Area Chezy roughness coefficient Hazen–Williams roughness coefficient Depth Critical depth Diameter Modulus of elasticity Force Acceleration due to gravity Total head, head on weir Head or height Head loss due to friction Length Mass Manning’s roughness coefficient Perimeter, weir height Force due to pressure Pressure
40816_12a_p381-431
Terminology
A C C1 d dc D E F g H h hf L M n P P p
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p383
383
Symbol
p382
1 s
n . s e
s
l
TABLE 12.1 Symbols, Terminology, Dimensions, and Units Used in Water Engineering
USCS units
L /T L3/TL L L T T, L L/T F F/L3
ft /s ft3/(sft) ft ft s s, ft ft/s lb lb/ft3
m3/s m3/sm m m s s, m m/s kg kg/m3
L L L FT/L2 L2/T FT2/L4 F/L F/L2
ft ft ft lbs/ft ft2/s lbs2/ft4 lb/ft lb/in2
m m m kgs/m m2/s kgs2/m4 kg/m MPa
3
SI units
TLFeBOOK
Page 384
Flow rate Unit flow rate Radius Hydraulic radius Time Time, thickness Velocity Weight Specific weight Depth in open channel, distance from solid boundary Height above datum Size of roughness Viscosity Kinematic viscosity Density Surface tension Shear stress
3
12:51 PM
Z "
Dimensions
10/22/01
384
Q q r R T t V W w y
Terminology
40816_12a_p381-431
Symbol
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p384
TABLE 12.1 Symbols, Terminology, Dimensions, and Units Used in Water Engineering (Continued)
4081
Shear stress
F/L
lb/in
MPa
p384
Weir coefficient, coefficient of discharge Coefficient of contraction Coefficient of velocity Froude number Darcy–Weisbach friction factor Head-loss coefficient Reynolds number Friction slope—slope of energy grade line Critical slope Efficiency Specific gravity
Page 385
TLFeBOOK
12:51 PM
C Cc Cv F f K R S Sc # Sp. gr.
10/22/01
385
Quantity
40816_12a_p381-431
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p385
Symbols for dimensionless quantities Symbol
40816_12a_p381-431
10/22/01
12:51 PM
Page 386
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p386
386
4081
CHAPTER TWELVE
w
V a i v b a t 0 t l
FIGURE 12.1 Capillary action raises water in a small-diameter tube. Meniscus, or liquid surface, is concave upward.
P C
VISCOSITY Viscosity of a fluid, also called the coefficient of viscosity, absolute viscosity, or dynamic viscosity, is a measure of its resistance to flow. It is expressed as the ratio of the tangential shearing stresses between flow layers to the rate of change of velocity with depth:
dV/dy TLFeBOOK
T (
w
40816_12a_p381-431 p386
10/22/01
12:51 PM
Page 387
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p387
HYDRAULICS AND WATERWORKS FORMULAS
387
where shearing stress, lb/ft2 (N/m2) V velocity, ft/s (m/s) y depth, ft (m) Viscosity decreases as temperature increases but may be assumed independent of changes in pressure for the majority of engineering problems. Water at 70°F (21.1°C) has a viscosity of 0.00002050 lbs/ft2 (0.00098 Ns/m2). Kinematic viscosity is defined as viscosity divided by density . It is so named because its units, ft2/s (m2/s), are a combination of the kinematic units of length and time. Water at 70°F (21.1°C) has a kinematic viscosity of 0.00001059 ft2/s (0.000001 Nm2/s). In hydraulics, viscosity is most frequently encountered in the calculation of Reynolds number to determine whether laminar, transitional, or completely turbulent flow exists.
.
PRESSURE ON SUBMERGED CURVED SURFACES
, s l f
The hydrostatic pressure on a submerged curved surface (Fig. 12.2) is given by P √PH2 PV2 where P total pressure force on the surface PH force due to pressure horizontally PV force due to pressure vertically TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 388
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p388
388
4081
CHAPTER TWELVE
w
FIGURE 12.2 Hydrostatic pressure on a submerged curved surface. (a) Pressure variation over the surface. (b) Free-body diagram.
u e a a t s m
FUNDAMENTALS OF FLUID FLOW For fluid energy, the law of conservation of energy is represented by the Bernoulli equation: Z1
p1 V 21 p V 22 Z2 2 w 2g w 2g TLFeBOOK
t ( e t ( c
40816_12a_p381-431 p388
10/22/01
12:51 PM
Page 389
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p389
HYDRAULICS AND WATERWORKS FORMULAS
389
where Z1 elevation, ft (m), at any point 1 of flowing fluid above an arbitrary datum Z2 elevation, ft (m), at downstream point in fluid above same datum p1 pressure at 1, lb/ft2 (kPa) p2 pressure at 2, lb/ft2 (kPa) w specific weight of fluid, lb/ft3 (kg/m3) V1 velocity of fluid at 1, ft/s (m/s) V2 velocity of fluid at 2, ft/s (m/s) g acceleration due to gravity, 32.2 ft/s2 (9.81 m/s2)
.
The left side of the equation sums the total energy per unit weight of fluid at 1, and the right side, the total energy per unit weight at 2. The preceding equation applies only to an ideal fluid. Its practical use requires a term to account for the decrease in total head, ft (m), through friction. This term hf , when added to the downstream side, yields the form of the Bernoulli equation most frequently used: Z1
-
p1 V 21 p V 22 Z2 2 hf w 2g w 2g
The energy contained in an elemental volume of fluid thus is a function of its elevation, velocity, and pressure (Fig. 12.3). The energy due to elevation is the potential energy and equals WZa, where W is the weight, lb (kg), of the fluid in the elemental volume and Za is its elevation, ft (m), above some arbitrary datum. The energy due to velocity is the kinetic energy. It equals WV a2 /2g, where Va is the TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 390
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p390
390
4081
CHAPTER TWELVE
a v t B w ( a
FIGURE 12.3 pressure.
Energy in a liquid depends on elevation, velocity, and
s i f i t t w i
velocity, ft/s (m/s). The pressure energy equals Wpa /w, where pa is the pressure, lb/ft2 (kg/kPa), and w is the specific weight of the fluid, lb/ft3 (kg/m3). The total energy in the elemental volume of fluid is E WZ a
Wpa WV 2a w 2g
Dividing both sides of the equation by W yields the energy per unit weight of flowing fluid, or the total head ft (m): H Za
pa V 2a w 2g
pa /w is called pressure head; V 2a /2g, velocity head. As indicated in Fig. 12.3, Z p/w is constant for any point in a cross section and normal to the flow through TLFeBOOK
F
40816_12a_p381-431 p390
10/22/01
12:51 PM
Page 391
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p391
HYDRAULICS AND WATERWORKS FORMULAS
d
391
a pipe or channel. Kinetic energy at the section, however, varies with velocity. Usually, Z p/w at the midpoint and the average velocity at a section are assumed when the Bernoulli equation is applied to flow across the section or when total head is to be determined. Average velocity, ft/s (m/s) Q/A, where Q is the quantity of flow, ft3/s (m3/s), across the area of the section A, ft2 (m2). Momentum is a fundamental concept that must be considered in the design of essentially all waterworks facilities involving flow. A change in momentum, which may result from a change in velocity, direction, or magnitude of flow, is equal to the impulse, the force F acting on the fluid times the period of time dt over which it acts (Fig. 12.4). Dividing the total change in momentum by the time interval over which the change occurs gives the momentum equation, or impulse-momentum equation:
, c e
y
y h
FIGURE 12.4
Force diagram for momentum.
TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 392
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p392
392
4081
CHAPTER TWELVE
Fx pQ Vx where Fx summation of all forces in X direction per unit time causing change in momentum in X direction, lb (N) density of flowing fluid, lbs2/ft4 (kgs2/m4) (specific weight divided by g)
w
Q flow rate, ft3/s (m3/s) Vx change in velocity in X direction, ft/s (m/s) Similar equations may be written for the Y and Z directions. The impulse–momentum equation often is used in conjunction with the Bernoulli equation but may be used separately.
w t F
SIMILITUDE FOR PHYSICAL MODELS A physical model is a system whose operation can be used to predict the characteristics of a similar system, or prototype, usually more complex or built to a much larger scale. Ratios of the forces of gravity, viscosity, and surface tension to the force of inertia are designated, Froude number, Reynolds number, and Weber number, respectively. Equating the Froude number of the model and the Froude number of the prototype ensures that the gravitational and inertial forces are in the same proportion. Similarly, equating the Reynolds numbers of the model and prototype ensures that the viscous and inertial forces are in the same proportion. Equating the Weber numbers ensures proportionality of surface tension and inertial forces. TLFeBOOK
w
R f a i o n e
40816_12a_p381-431 p392
10/22/01
12:51 PM
Page 393
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p393
HYDRAULICS AND WATERWORKS FORMULAS
393
The Froude number is r n
F
V √Lg
where F Froude number (dimensionless) V velocity of fluid, ft/s (m/s) ) . .
L linear dimension (characteristic, such as depth or diameter), ft (m) g acceleration due to gravity, 32.2 ft/s2 (9.81 m/s2) For hydraulic structures, such as spillways and weirs, where there is a rapidly changing water-surface profile, the two predominant forces are inertia and gravity. Therefore, the Froude numbers of the model and prototype are equated: Fm Fp
e r r e , r l e t . -
Vm Vp √Lm g √Lp g
where subscript m applies to the model and p to the prototype. The Reynolds number is R
VL
R is dimensionless, and is the kinematic viscosity of fluid, ft2/s (m2/s). The Reynolds numbers of model and prototype are equated when the viscous and inertial forces are predominant. Viscous forces are usually predominant when flow occurs in a closed system, such as pipe flow where there is no free surface. The following relations are obtained by equating Reynolds numbers of the model and prototype: TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 394
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p394
394
4081
CHAPTER TWELVE
Vm Lm Vp Lp vm vp
Vr
vr Lr
The variable factors that fix the design of a true model when the Reynolds number governs are the length ratio and the viscosity ratio. The Weber number is W
I t h
V 2 L
where density of fluid, lbs2/ft4 (kgs2/m4) (specific weight divided by g); and surface tension of fluid, lb/ft2 (kPa). The Weber numbers of model and prototype are equated in certain types of wave studies. For the flow of water in open channels and rivers where the friction slope is relatively flat, model designs are often based on the Manning equation. The relations between the model and prototype are determined as follows:
w
I n
F
1/2 (1.486/nm)R2/3 Vm m Sm 1/2 Vp (1.486/np)R2/3 p Sp
where n Manning roughness coefficient (T/L1/3, T representing time) R hydraulic radius (L) S loss of head due to friction per unit length of conduit (dimensionless) slope of energy gradient For true models, Sr 1, Rr Lr. Hence, TLFeBOOK
L I o fl d s o c v
40816_12a_p381-431 p394
10/22/01
12:51 PM
Page 395
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p395
HYDRAULICS AND WATERWORKS FORMULAS
Vr l d
395
L2/3 r nr
In models of rivers and channels, it is necessary for the flow to be turbulent. The U.S. Waterways Experiment Station has determined that flow is turbulent if VR 4000
c , d e n e
where V mean velocity, ft/s (m/s) R hydraulic radius, ft (m) kinematic viscosity, ft2/s (m2/s) If the model is to be a true model, it may have to be uneconomically large for the flow to be turbulent.
FLUID FLOW IN PIPES Laminar Flow -
f
In laminar flow, fluid particles move in parallel layers in one direction. The parabolic velocity distribution in laminar flow, shown in Fig. 12.5, creates a shearing stress dV/dy, where dV/dy is the rate of change of velocity with depth, and is the coefficient of viscosity. As this shearing stress increases, the viscous forces become unable to damp out disturbances, and turbulent flow results. The region of change is dependent on the fluid velocity, density, and viscosity and the size of the conduit. TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 396
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p396
396
4081
CHAPTER TWELVE
t i
w FIGURE 12.5 Velocity distribution for lamellar flow in a circular pipe is parabolic. Maximum velocity is twice the average velocity.
A dimensionless parameter called the Reynolds number has been found to be a reliable criterion for the determination of laminar or turbulent flow. It is the ratio of inertial forces/viscous forces, and is given by R
VD VD
F D t
where V fluid velocity, ft/s (m/s) D pipe diameter, ft (m) density of fluid, lbs2/ft4 (kgs2/m4) (specific weight divided by g, 32.2 ft/s2) viscosity of fluid lbs/ft2 (kgs/m2) / kinematic viscosity, ft2/s (m2/s) For a Reynolds number less than 2000, flow is laminar in circular pipes. When the Reynolds number is greater than 2000, laminar flow is unstable; a disturbance is probably magnified, causing the flow to become turbulent. TLFeBOOK
T I f t w t i c f fl
40816_12a_p381-431 p396
10/22/01
12:51 PM
Page 397
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p397
397
HYDRAULICS AND WATERWORKS FORMULAS
In laminar flow, the following equation for head loss due to friction can be developed by considering the forces acting on a cylinder of fluid in a pipe: hf
32LV 32LV D2g D2 w
where hf head loss due to friction, ft (m) r
L length of pipe section considered, ft (m) g acceleration due to gravity, 32.2 ft/s2 (9.81 m/s2)
r l
w specific weight of fluid, lb/ft3 (kg/m3) Substitution of the Reynolds number yields hf
64 L V 2 R D 2g
For laminar flow, the preceding equation is identical to the Darcy–Weisbach formula because, in laminar flow, the friction f 64/R.
Turbulent Flow
n n y
In turbulent flow, the inertial forces are so great that viscous forces cannot dampen out disturbances caused primarily by the surface roughness. These disturbances create eddies, which have both a rotational and translational velocity. The translation of these eddies is a mixing action that affects an interchange of momentum across the cross section of the conduit. As a result, the velocity distribution is more uniform, as shown in Fig. 12.6. Experimentation in turbulent flow has shown that TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 398
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p398
398
4081
CHAPTER TWELVE
FIGURE 12.6 Velocity distribution for turbulent flow in a circular pipe is more nearly uniform than that for lamellar flow.
The head loss varies directly as the length of the pipe. The head loss varies almost as the square of the velocity. The head loss varies almost inversely as the diameter. The head loss depends on the surface roughness of the pipe wall. The head loss depends on the fluid density and viscosity. The head loss is independent of the pressure.
Darcy–Weisbach Formula One of the most widely used equations for pipe flow, the Darcy–Weisbach formula satisfies the condition described in the preceding section and is valid for laminar or turbulent flow in all fluids: L V2 hf f D 2g where hf head loss due to friction, ft (m) f friction factor (see an engineering handbook) L length of pipe, ft (m) TLFeBOOK
I f T E g w g l i t f m b e
C T s
w
40816_12a_p381-431 p398
10/22/01
12:51 PM
Page 399
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p399
HYDRAULICS AND WATERWORKS FORMULAS
399
D diameter of pipe, ft (m) V velocity of fluid, ft/s (m/s) g acceleration due to gravity, 32.2 ft/s2 (9.81 m/s2) r
. e .
e d -
It employs the Moody diagram for evaluating the friction factor f. (Moody, L. F., “Friction Factors for Pipe Flow,” Transactions of the American Society of Mechanical Engineers, November 1944.) Because the preceding equation is dimensionally homogeneous, it can be used with any consistent set of units without changing the value of the friction factor. Roughness values ", ft (m), for use with the Moody diagram to determine the Darcy–Weisbach friction factor f are listed in engineering handbooks. The following formulas were derived for head loss in waterworks design and give good results for watertransmission and -distribution calculations. They contain a factor that depends on the surface roughness of the pipe material. The accuracy of these formulas is greatly affected by the selection of the roughness factor, which requires experience in its choice.
Chezy Formula This equation holds for head loss in conduits and gives reasonably good results for high Reynolds numbers: V C √RS where V velocity, ft/s (m/s)
)
C coefficient, dependent on surface roughness of conduit TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 400
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p400
400
4081
CHAPTER TWELVE
S slope of energy grade line or head loss due to friction, ft/ft (m/m) of conduit R hydraulic radius, ft (m) Hydraulic radius of a conduit is the cross-sectional area of the fluid in it divided by the perimeter of the wetted section. w Manning’s Formula Through experimentation, Manning concluded that the C in the Chezy equation should vary as R1/6: C
1/6
1.486R n
H T c f
where n coefficient, dependent on surface roughness. (Although based on surface roughness, n in practice is sometimes treated as a lumped parameter for all head losses.) Substitution gives V
1.486 2/3 1/2 R S n
On substitution of D/4, where D is the pipe diameter, for the hydraulic radius of the pipe, the following equations are obtained for pipes flowing full: V
0.590 2/3 1/2 D S n
w
0.463 8/3 1/2 Q D S n TLFeBOOK
40816_12a_p381-431 p400
10/22/01
12:51 PM
Page 401
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p401
HYDRAULICS AND WATERWORKS FORMULAS
o
f .
hf 4.66n2
D
401
LQ2 D16/3
2.159Qn S
3/8
1/2
where Q flow, ft3/s (m3/s).
n
Hazen–Williams Formula This is one of the most widely used formulas for pipe-flow computations of water utilities, although it was developed for both open channels and pipe flow:
. )
V 1.318C1R0.63S 0.54 For pipes flowing full: V 0.55C1D0.63S 0.54 Q 0.432C1D2.63S 0.54
r e
hf D
4.727 L D4.87 1.376 S0.205
CQ
1.85
1
CQ
0.38
1
where V velocity, ft/s (m/s) C1 coefficient, dependent on surface roughness (given in engineering handbooks) TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 402
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p402
402
4081
CHAPTER TWELVE
R hydraulic radius, ft (m) S head loss due to friction, ft/ft (m/m) of pipe D diameter of pipe, ft (m) w
L length of pipe, ft (m) Q discharge, ft3/s (m3/s) hf friction loss, ft (m) Figure 12.7 shows a typical three-reservoir problem. The elevations of the hydraulic grade lines for the three pipes are equal at point D. The Hazen–Williams equation for friction loss can be written for each pipe meeting at D. With the continuity equation for quantity of flow, there are as many equations as there are unknowns: Za Zd
4.727L A pD w D 4.87 A
QC
Zb Zd
PD 4.727L B w D 4.87 B
QC
A
1.85
P P E m u t l m
A
B
1.85
S
B
T s a
w
FIGURE 12.7
Flow between reservoirs.
TLFeBOOK
40816_12a_p381-431 p402
10/22/01
12:51 PM
Page 403
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p403
HYDRAULICS AND WATERWORKS FORMULAS
Zc Zd
4.727L C PD w D 4.87 C
403
QC C
1.85
C
QA QB QC where pD pressure at D, and w unit weight of liquid.
. e n . e
PRESSURE (HEAD) CHANGES CAUSED BY PIPE SIZE CHANGE Energy losses occur in pipe contractions, bends, enlargements, and valves and other pipe fittings. These losses can usually be neglected if the length of the pipeline is greater than 1500 times the pipe diameter. However, in short pipelines, because these losses may exceed the friction losses, minor losses must be considered.
Sudden Enlargements The following equation for the head loss, ft (m), across a sudden enlargement of pipe diameter has been determined analytically and agrees well with experimental results: hL
(V1 V2)2 2g
where V1 velocity before enlargement, ft/s (m/s) V2 velocity after enlargement, ft/s (m/s) g 32.2 ft/s2 (9.81 m/s2) TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 404
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p404
404
4081
CHAPTER TWELVE
It was derived by applying the Bernoulli equation and the momentum equation across an enlargement. Another equation for the head loss caused by sudden enlargements was determined experimentally by Archer. This equation gives slightly better agreement with experimental results than the preceding formula: hL
w s r b B
1.1(V1 V2)1.92 2g
A special application of these two preceding formulas is the discharge from a pipe into a reservoir. The water in the reservoir has no velocity, so a full velocity head is lost.
T 1 f h s
Gradual Enlargements The equation for the head loss due to a gradual conical enlargement of a pipe takes the following form: K(V1 V2)2 hL 2g
B T a
where K loss coefficient, as given in engineering handbooks.
Sudden Contraction
f
The following equation for the head loss across a sudden contraction of a pipe was determined by the same type of analytic studies as hL
C1
c
1
2
V2 2g
w e TLFeBOOK
40816_12a_p381-431 p404
10/22/01
12:51 PM
Page 405
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p405
HYDRAULICS AND WATERWORKS FORMULAS
e n . -
where Cc coefficient of contraction; and V velocity in smaller diameter pipe, ft/s (m/s). This equation gives best results when the head loss is greater than 1 ft (0.3 m). Another formula for determining the loss of head caused by a sudden contraction, determined experimentally by Brightmore, is hL
e e
405
0.7(V1 V2)2 2g
This equation gives best results if the head loss is less than 1 ft (0.3 m). A special case of sudden contraction is the entrance loss for pipes. Some typical values of the loss coefficient K in hL KV 2/2g, where V is the velocity in the pipe, are presented in engineering handbooks.
l Bends and Standard Fitting Losses The head loss that occurs in pipe fittings, such as valves and elbows, and at bends is given by hL
KV 2 2g
To obtain losses in bends other than 90°, the following formula may be used to adjust the K values: n f
K K
√
90
where deflection angle, degrees. K values are given in engineering handbooks. TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 406
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p406
406
4081
CHAPTER TWELVE
FLOW THROUGH ORIFICES An orifice is an opening with a closed perimeter through which water flows. Orifices may have any shape, although they are usually round, square, or rectangular.
Orifice Discharge into Free Air Discharge through a sharp-edged orifice may be calculated from Q Ca√2gh where Q discharge, ft3/s (m3/s) C coefficient of discharge
F
a area of orifice, ft2 (m2)
v f
g acceleration due to gravity, ft/s2 (m/s2) h head on horizontal center line of orifice, ft (m) Coefficients of discharge C are given in engineering handbooks for low velocity of approach. If this velocity is significant, its effect should be taken into account. The preceding formula is applicable for any head for which the coefficient of discharge is known. For low heads, measuring the head from the center line of the orifice is not theoretically correct; however, this error is corrected by the C values. The coefficient of discharge C is the product of the coefficient of velocity Cv and the coefficient of contraction Cc. The coefficient of velocity is the ratio obtained by dividing the actual velocity at the vena contracta (contraction of the jet discharged) by the theoretical velocity. The theoretical TLFeBOOK
W p b
s t i
40816_12a_p381-431 p406
10/22/01
12:51 PM
Page 407
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p407
HYDRAULICS AND WATERWORKS FORMULAS
407
h h
d
FIGURE 12.8
Fluid jet takes a parabolic path.
velocity may be calculated by writing Bernoulli’s equation for points 1 and 2 in Fig. 12.8. ) g s e g y . g e l
p V 22 p V 21 1 Z1 2 Z2 2g w 2g w With the reference plane through point 2, Z1 h, V1 0, p1/w p2/w 0, and Z2 0, the preceding formula becomes V2 √2gh The coefficient of contraction Cc is the ratio of the smallest area of the jet, the vena contracta, to the area of the orifice. Contraction of a fluid jet occurs if the orifice is square edged and so located that some of the fluid TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 408
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p408
408
4081
CHAPTER TWELVE
approaches the orifice at an angle to the direction of flow through the orifice.
V f
Submerged Orifices
D
Flow through a submerged orifice may be computed by applying Bernoulli’s equation to points 1 and 2 in Fig. 12.9:
T t t r t v i
V2
√
2g h1 h2
V 21 hL 2g
where hL losses in head, ft (m), between 1 and 2. By assuming V1 0, setting h1 h2 h, and using a coefficient of discharge C to account for losses, the following formula is obtained:
w
Q Ca √2g h
F W c a
FIGURE 12.9
w C
Discharge through a submerged orifice.
TLFeBOOK
40816_12a_p381-431 p408
10/22/01
12:51 PM
Page 409
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p409
HYDRAULICS AND WATERWORKS FORMULAS
w
409
Values of C for submerged orifices do not differ greatly from those for nonsubmerged orifices.
Discharge under Falling Head y :
The flow from a reservoir or vessel when the inflow is less than the outflow represents a condition of falling head. The time required for a certain quantity of water to flow from a reservoir can be calculated by equating the volume of water that flows through the orifice or pipe in time dt to the volume decrease in the reservoir. If the area of the reservoir is constant,
g -
t
2A Ca √2g
√h1 √h2
where h1 head at the start, ft (m) h2 head at the end, ft (m) t time interval for head to fall from h1 to h2, s
FLUID JETS Where the effect of air resistance is small, a fluid discharged through an orifice into the air follows the path of a projectile. The initial velocity of the jet is V0 Cv √2gh where h head on center line of orifice, ft (m), and Cv coefficient of velocity. TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 410
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p410
410
4081
CHAPTER TWELVE
The direction of the initial velocity depends on the orientation of the surface in which the orifice is located. For simplicity, the following equations were determined assuming the orifice is located in a vertical surface (see Fig. 12.8). The velocity of the jet in the X direction (horizontal) remains constant: Vx V0 Cv √2gh The velocity in the Y direction is initially zero and thereafter a function of time and the acceleration of gravity: Vy gt
F v
t 1
The X coordinate at time t is X Vx t tCv √2gh The Y coordinate is Y Vavg t
gt2 2
w
where Vavg average velocity over period of time t. The equation for the path of the jet: X 2 Cv24hY
ORIFICE DISCHARGE INTO DIVERGING CONICAL TUBES
D t
This type of tube can greatly increase the flow through an orifice by reducing the pressure at the orifice below atmospheric. The formula that follows for the pressure at the entrance to the
t v m
TLFeBOOK
40816_12a_p381-431 p410
10/22/01
12:51 PM
Page 411
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p411
411
HYDRAULICS AND WATERWORKS FORMULAS
e r . )
-
FIGURE 12.10 Diverging conical tube increases flow from a reservoir through an orifice by reducing the pressure below atmospheric.
tube is obtained by writing the Bernoulli equation for points 1 and 3 and points 1 and 2 in Fig. 12.10:
aa
p2 wh 1
3
2
2
where p2 gage pressure at tube entrance, lb/ft2 (Pa) w unit weight of water, lb/ft3 (kg/m3) e
h head on centerline of orifice, ft (m) a2 area of smallest part of jet (vena contracta, if one exists), ft2 (m) a3 area of discharge end of tube, ft2 (m2)
. e
Discharge is also calculated by writing the Bernoulli equation for points 1 and 3 in Fig. 12.10. For this analysis to be valid, the tube must flow full, and the pressure in the throat of the tube must not fall to the vapor pressure of water. Experiments by Venturi show the most efficient angle to be around 5°. TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 412
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p412
412
4081
CHAPTER TWELVE
WATER HAMMER Water hammer is a change is pressure, either above or below the normal pressure, caused by a variation of the flow rate in a pipe. The equation for the velocity of a wave in a pipe is U
E
√ √
1 1 ED/Ep t
where U velocity of pressure wave along pipe, ft/s (m/s)
F
E modulus of elasticity of water, 43.2 106 lb/ft2 (2.07 106 kPa) density of water, 1.94 lbs/ft4 (specific weight divided by acceleration due to gravity) D diameter of pipe, ft (m)
o p i t
Ep modulus of elasticity of pipe material, lb/ft2 (kg/m2) w
t thickness of pipe wall, ft (m)
PIPE STRESSES PERPENDICULAR TO THE LONGITUDINAL AXIS
H
The stresses acting perpendicular to the longitudinal axis of a pipe are caused by either internal or external pressures on the pipe walls. Internal pressure creates a stress commonly called hoop tension. It may be calculated by taking a free-body diagram TLFeBOOK
w n
40816_12a_p381-431 p412
10/22/01
12:51 PM
Page 413
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p413
HYDRAULICS AND WATERWORKS FORMULAS
413
r w
) FIGURE 12.11
Internal pipe pressure produces hoop tension.
2
t
2
of a 1-in (25.4-mm)-long strip of pipe cut by a vertical plane through the longitudinal axis (Fig. 12.11). The forces in the vertical direction cancel out. The sum of the forces in the horizontal direction is pD 2F where p internal pressure, lb/in2 (MPa) D outside diameter of pipe, in (mm) F force acting on each cut of edge of pipe, lb (N) Hence, the stress, lb/in2 (MPa) on the pipe material is
f n p m
f
F pD A 2t
where A area of cut edge of pipe, ft2 (m2); and t thickness of pipe wall, in (mm). TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 414
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p414
414
4081
CHAPTER TWELVE
TEMPERATURE EXPANSION OF PIPE If a pipe is subject to a wide range of temperatures, the stress, lb/in2 (MPa), due to a temperature change is f cE T where E modulus of elasticity of pipe material, lb/in2 (MPa) T temperature change from installation temperature c coefficient of thermal expansion of pipe material The movement that should be allowed for, if expansion joints are to be used, is L Lc T where L movement in length L of pipe, and L length between expansion joints.
FORCES DUE TO PIPE BENDS It is common practice to use thrust blocks in pipe bends to take the forces on the pipe caused by the momentum change and the unbalanced internal pressure of the water. The force diagram in Fig. 12.12 is a convenient method for finding the resultant force on a bend. The forces can be resolved into X and Y components to find the magnitude and direction of the resultant force on the pipe. In Fig. 12.12, TLFeBOOK
F i
40816_12a_p381-431 p414
10/22/01
12:51 PM
Page 415
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p415
HYDRAULICS AND WATERWORKS FORMULAS
415
e
2
l n
h
FIGURE 12.12 in diameter.
Forces produced by flow at a pipe bend and change
V1 velocity before change in size of pipe, ft/s (m/s) V2 velocity after change in size of pipe, ft /s (m/s) p1 pressure before bend or size change in pipe, lb/ft2 (kPa)
o e d e d
p2 pressure after bend or size change in pipe, lb/ft2 (kPa) A1 area before size change in pipe, ft2 (m2) A2 area after size change in pipe, ft2 (m2) F2m force due to momentum of water in section 2 V2Qw/g TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 416
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p416
416
4081
CHAPTER TWELVE
F1m force due to momentum of water in section 1 V1Qw/g
C
P2 pressure of water in section 2 times area of section 2 p2 A2
A d b d B e m
P1 pressure of water in section 1 times area of section 1 p1 A1 w unit weight of liquid, lb/ft3 (kg/m3) Q discharge, ft3/s (m3/s) If the pressure loss in the bend is neglected and there is no change in magnitude of velocity around the bend, a quick solution is
R 2A w
V2 p cos g 2
c b w
E W t s t
2 where R resultant force on bend, lb (N)
a e
angle R makes with F1m p pressure, lb/ft2 (kPa) w unit weight of water, 62.4 lb/ft3 (998.4 kg/m3)
S
V velocity of flow, ft/s (m/s) g acceleration due to gravity, 32.2 ft/s2 (9.81 m/s2) A area of pipe, ft2 (m2)
w
angle between pipes (0° 180°) TLFeBOOK
40816_12a_p381-431 p416
10/22/01
12:51 PM
Page 417
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p417
HYDRAULICS AND WATERWORKS FORMULAS
417
CULVERTS -
o k
A culvert is a closed conduit for the passage of surface drainage under a highway, a railroad, a canal, or other embankment. The slope of a culvert and its inlet and outlet conditions are usually determined by the topography of the site. Because of the many combinations obtained by varying the entrance conditions, exit conditions, and slope, no single formula can be given that applies to all culvert problems. The basic method for determining discharge through a culvert requires application of the Bernoulli equation between a point just outside the entrance and a point somewhere downstream.
Entrance and Exit Submerged When both the exit and entrance are submerged (Fig. 12.13), the culvert flows full, and the discharge is independent of the slope. This is normal pipe flow and is easily solved by using the Manning or Darcy–Weisbach formula for friction loss. From the Bernoulli equation for the entrance and exit, and the Manning equation for friction loss, the following equation is obtained: H (1 Ke) )
V 2n2L V2 2g 2.21R 4/3
Solution for the velocity of flow yields )
V
√
H (1 Ke/2g) (n2 L /2.21R4/3)
where H elevation difference between headwater and tailwater, ft (m) TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 418
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p418
418
4081
CHAPTER TWELVE
FIGURE 12.13 With entrance and exit of a culvert submerged, normal pipe flow occurs. Discharge is independent of slope. The fluid flows under pressure. Discharge may be determined from Bernoulli and Manning equations.
V velocity in culvert, ft/s (m/s) g acceleration due to gravity, 32.2 ft/s2 (9.81 m/s2)
F c e h
E t e o o s
Ke entrance-loss coefficient n Manning’s roughness coefficient L length of culvert, ft (m) R hydraulic radius of culvert, ft (m) The preceding equation can be solved directly because the velocity is the only unknown.
e
Culverts on Subcritical Slopes Critical slope is the slope just sufficient to maintain flow at critical depth. When the slope is less than critical, the flow is considered subcritical. TLFeBOOK
B
40816_12a_p381-431 p418
10/22/01
12:51 PM
Page 419
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p419
HYDRAULICS AND WATERWORKS FORMULAS
, d d
)
FIGURE 12.14 Open-channel flow occurs in a culvert with free discharge and normal depth dn greater than the critical depth dc when the entrance is unsubmerged or slightly submerged. Discharge depends on head H, loss at entrance, and slope of culvert.
Entrance Submerged or Unsubmerged but Free Exit. For these conditions, depending on the head, the flow can be either pressure or open channel (Fig. 12.14). The discharge for the open-channel condition is obtained by writing the Bernoulli equation for a point just outside the entrance and a point a short distance downstream from the entrance. Thus, H Ke
e
V2 V2 dn 2g 2g
The velocity can be determined from the Manning equation: V2
t w
419
2.2SR4/3 n2
By substituting this into H (1 Ke)
2.2 SR 4/3 dn 2gn2 TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 420
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p420
420
4081
CHAPTER TWELVE
where H head on entrance measured from bottom of culvert, ft (m) Ke entrance-loss coefficient S slope of energy grade line, which for culverts is assumed to equal slope of bottom of culvert
w
W t
R hydraulic radius of culvert, ft (m) dn normal depth of flow, ft (m) To solve the preceding head equation, it is necessary to try different values of dn and corresponding values of R until a value is found that satisfies the equation.
OPEN-CHANNEL FLOW Free surface flow, or open-channel flow, includes all cases of flow in which the liquid surface is open to the atmosphere. Thus, flow in a pipe is open-channel flow if the pipe is only partly full. A uniform channel is one of constant cross section. It has uniform flow if the grade, or slope, of the water surface is the same as that of the channel. Hence, depth of flow is constant throughout. Steady flow in a channel occurs if the depth at any location remains constant with time. The discharge Q at any section is defined as the volume of water passing that section per unit of time. It is expressed in cubic feet per second, ft3/s (cubic meter per second, m3/s), and is given by Q VA TLFeBOOK
w T t f w c T i d
w d
40816_12a_p381-431 p420
10/22/01
12:51 PM
Page 421
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p421
421
HYDRAULICS AND WATERWORKS FORMULAS
f
where V average velocity, ft/s (m/s) A cross-sectional area of flow, ft2 (m2)
s t
o R
s e t e h e s r
When the discharge is constant, the flow is said to be continuous and therefore Q V1 A1 V2 A2 where the subscripts designate different channel sections. This preceding equation is known as the continuity equation for continuous steady flow. Depth of flow d is taken as the vertical distance, ft (m), from the bottom of a channel to the water surface. The wetted perimeter is the length, ft (m), of a line bounding the cross-sectional area of flow minus the free surface width. The hydraulic radius R equals the area of flow divided by its wetted perimeter. The average velocity of flow V is defined as the discharge divided by the area of flow: V
Q A
The velocity head HV, ft (m), is generally given by HV
V2 2g
where V average velocity, ft/s (m/s); and g acceleration due to gravity, 32.2 ft/s2 (9.81 m/s2). The true velocity head may be expressed as HVa
V2 2g TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 422
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p422
422
4081
CHAPTER TWELVE
where is an empirical coefficient that represents the degree of turbulence. Experimental data indicate that may vary from about 1.03 to 1.36 for prismatic channels. It is, however, normally taken as 1.00 for practical hydraulic work and is evaluated only for precise investigations of energy loss. The total energy per pound (kilogram) of water relative to the bottom of the channel at a vertical section is called the specific energy head He. It is composed of the depth of flow at any point, plus the velocity head at the point. It is expressed in feet (meter) as He d
V2 2g
A longitudinal profile of the elevation of the specific energy head is called the energy grade line, or the total-head line (Fig. 12.15). A longitudinal profile of the water surface is called the hydraulic grade line. The vertical distance between these profiles at any point equals the velocity head at that point.
e d
N T F u b s o
w
A
C
FIGURE 12.15
F t t
Characteristics of uniform open-channel flow.
TLFeBOOK
40816_12a_p381-431 p422
10/22/01
12:51 PM
Page 423
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p423
HYDRAULICS AND WATERWORKS FORMULAS
e y , k . e d f s
y e s n .
423
Loss of head due to friction hf in channel length L equals the drop in elevation of the channel Z in the same distance.
Normal Depth of Flow The depth of equilibrium flow that exists in the channel of Fig. 12.15 is called the normal depth dn. This depth is unique for specific discharge and channel conditions. It may be computed by a trial-and-error process when the channel shape, slope, roughness, and discharge are known. A form of the Manning equation is suggested for this calculation: AR2/3
Qn 1.486S1/2
where A area of flow, ft2 (m2) R hydraulic radius, ft (m) Q amount of flow or discharge, ft3/s (m3/s) n Manning’s roughness coefficient S slope of energy grade line or loss of head, ft (m), due to friction per linear ft (m), of channel AR2/3 is referred to as a section factor.
Critical Depth of Open-Channel Flow For a given value of specific energy, the critical depth gives the greatest discharge, or conversely, for a given discharge, the specific energy is a minimum for the critical depth. TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 424
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p424
424
4081
CHAPTER TWELVE
For rectangular channels, the critical depth, dc ft (m), is given by 3
dc
√
Q2 b2g
w f M
where dc critical depth, ft (m) Q quantity of flow or discharge, ft3/s (m3/s) B
b width of channel, ft (m)
MANNING’S EQUATION FOR OPEN CHANNELS
w f
One of the more popular of the numerous equations developed for determination of flow in an open channel is Manning’s variation of the Chezy formula:
H
V C √RS where R hydraulic radius, ft (m) V mean velocity of flow, ft/s (m/s) S slope of energy grade line or loss of head due to friction, ft/linear ft (m/m), of channel C Chezy roughness coefficient
d f b a o
Manning proposed: C
T ( t e i o r
1.4861/6 n TLFeBOOK
40816_12a_p381-431 p424
10/22/01
12:51 PM
Page 425
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p425
HYDRAULICS AND WATERWORKS FORMULAS
s
425
where n is the coefficient of roughness in the Ganguillet–Kutter formula. When Manning’s C is used in the Chezy formula, the Manning equation for flow velocity in an open channel results: V
1.486 2/3 1/2 R S n
Because the discharge Q VA, this equation may be written: Q
1.486 AR2/3S1/2 n
where A area of flow, ft2 (m2); and Q quantity of flow, ft3/s (m3/s). s
HYDRAULIC JUMP
e
This is an abrupt increase in depth of rapidly flowing water (Fig. 12.16). Flow at the jump changes from a supercritical to a subcritical stage with an accompanying loss of kinetic energy. Depth at the jump is not discontinuous. The change in depth occurs over a finite distance, known as the length of jump. The upstream surface of the jump, known as the roller, is a turbulent mass of water. The depth before a jump is the initial depth, and the depth after a jump is the sequent depth. The specific energy for the sequent depth is less than that for the initial depth because of the energy dissipation within the jump. (Initial and sequent depths should not be confused with the depths of equal energy, or alternate depths.) TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 426
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p426
426
4081
CHAPTER TWELVE
T FIGURE 12.16 Hydraulic jump.
The pressure force F developed in hydraulic jump is F
d 22 w d12 w 2 2
where d1 depth before jump, ft (m)
e (
d2 depth after jump, ft (m) w unit weight of water, lb/ft3 (kg/m3) The rate of change of momentum at the jump per foot width of channel equals F
qw MV1 MV2 (V1 V2) t g
w ( f r
where M mass of water, lbs2/ft (kgs2/m) V1 velocity at depth d1, ft/s (m/s) V2 velocity at depth d2, ft/s (m/s) TLFeBOOK
40816_12a_p381-431 p426
10/22/01
12:51 PM
Page 427
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p427
HYDRAULICS AND WATERWORKS FORMULAS
427
q discharge per foot width of rectangular channel, ft3/s (m3/s) t unit of time, s g acceleration due to gravity, 32.2 ft/s2 (9.81 kg/s2) Then
V 21
gd2 (d d1) 2d1 2
d2
d1 2
d1
d 2 2
√ √
2V 21 d1 d 21 g 4 d 22 2V 22 d2 g 4
The head loss in a jump equals the difference in specificenergy head before and after the jump. This difference (Fig. 12.17) is given by He He1 He2 t
(d2 d1)3 4d1 d2
where He1 specific-energy head of stream before jump, ft (m); and He2 specific-energy head of stream after jump, ft (m). The depths before and after a hydraulic jump may be related to the critical depth by
d1d2
d1 d2 q2 d3c 2 g TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 428
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p428
428
4081
CHAPTER TWELVE
F o
b
N
FIGURE 12.17
Type of hydraulic jump depends on Froude number.
where q discharge, ft3/s (m3/s) per ft (m) of channel width; and dc critical depth for the channel, ft (m). It may be seen from this equation that if d1 dc, d2 must also equal dc. TLFeBOOK
S o a ( m d a o s fl
40816_12a_p381-431 p428
10/22/01
12:51 PM
Page 429
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p429
HYDRAULICS AND WATERWORKS FORMULAS
429
FIGURE 12.18 Length of hydraulic jump in a horizontal channel depends on sequent depth d2 and the Froude number of the approaching flow.
Figure 12.18 shows how the length of hydraulic jump may be computed using the Froude number and the L/d2 ratio.
NONUNIFORM FLOW IN OPEN CHANNELS
r.
l 2
Symbols used in this section are V velocity of flow in the open channel, ft/s (m/s); Dc critical depth, ft (m); g acceleration due to gravity, ft/s2 (m/s2); Q flow rate, ft3/s (m3/s); q flow rate per unit width, ft3/ft (m3/m); Hm minimum specific energy, ftlb/lb (kgm/kg). Channel dimensions are in feet or meters and the symbols for them are given in the text and illustrations. Nonuniform flow occurs in open channels with gradual or sudden changes in the cross-sectional area of the fluid stream. The terms gradually varied flow and rapidly varied flow are used to describe these two types of nonuniform TLFeBOOK
40816_12a_p381-431
10/22/01
12:51 PM
Page 430
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p430
430
4081
CHAPTER TWELVE
A w
a
FIGURE 12.19
Energy of open-channel fluid flow.
flow. Equations are given next for flow in (1) rectangular cross-section channels, (2) triangular channels, (3) parabolic channels, (4) trapezoidal channels, and (5) circular channels. These five types of channels cover the majority of actual examples met in the field. Figure 12.19 shows the general energy relations in open-channel flow.
a
Rectangular Channels
W
In a rectangular channel, the critical depth Dc equals the mean depth Dm; the bottom width of the channel b equals the top width T; and when the discharge of fluid is taken as the flow per foot (meter) of width q of the channel, both b and T equal unity. Then Vc, the average velocity, is
and
Vc √gDc
(12.1)
Vc2 g
(12.2)
Dc
TLFeBOOK
T I a
40816_12a_p381-431 p430
10/22/01
12:51 PM
Page 431
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p431
HYDRAULICS AND WATERWORKS FORMULAS
Also
Q √g bD3/2 c
431
(12.3)
where g acceleration due to gravity in USCS or SI units. q √g D3/2 c 3
Dc
and
√
q2 g
(12.4) (12.5)
The minimum specific energy is Hm 32 Dc r c f e
(12.6)
and the critical depth is Dc 23 Hm
(12.7)
Then the discharge per foot (meter) of width is given by q √g (23)3/2H3/2 m
(12.8)
With g 32.16, Eq. (12.8) becomes e s n h
) )
q 3.087H 3/2 m
(12.9)
Triangular Channels In a triangular channel (Fig. 12.20), the maximum depth Dc and the mean depth Dm equal 12 Dc. Then, Vc
√
gDc 2
(12.10) TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 432
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p432
432
CHAPTER TWELVE
2V 2c g
Dc
and
(12.11)
As shown in Fig. 12.20, z is the slope of the channel sides, expressed as a ratio of horizontal to vertical; for symmetrical sections, z e/Dc. The area, a zD2c . Then, Q
√
g zD5/2 c 2
Dc
and
Q
or
√
g 2
√
T t t
a
Q 4.01zD5/2 c 5
P
(12.12)
With g 32.16, (12.13)
F
2
2Q gz2
45
(12.14)
W
5/2
zHm5/2
(12.15) a
With g 32.16, Q 2.295zH5/2 m
FIGURE 12.20
4081
(12.16)
F
Triangular open channel.
TLFeBOOK
40816_12b_p432-450 p432
10/22/01
12:52 PM
Page 433
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p433
HYDRAULICS AND WATERWORKS FORMULAS
) l -
433
Parabolic Channels These channels can be conveniently defined in terms of the top width T and the depth Dc. Then the area a 23DcT and the mean depth Dm. Then (Fig. 12.21), Vc √23 gDc
(12.17)
3 V2c 2 g
(12.18)
8g TD3/2 c 27
(12.19)
Q 3.087TD3/2 c
(12.20)
Q2 gT 2
(12.21)
) and )
Further,
)
With g 32.16,
Dc Q
√
) and
Dc
3 2
3
√
)
FIGURE 12.21 Parabolic open channel. TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 434
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p434
434
4081
CHAPTER TWELVE
Q
Also
√
8g 27
34
T
3/2
TH3/2 m
(12.22)
With g 32.16, Q 2.005TH3/2 m
(12.23)
T
Trapezoidal Channels Figure 12.22 shows a trapezoidal channel having a depth of Dc and a bottom width b. The slope of the sides, horizontal divided by vertical, is z. Expressing the mean depth Dm in terms of channel dimensions, the relations for critical depth Dc and average velocity Vc are Vc
and
Dc
√
b zDc gDc b 2zDc
V c2 b c 2z
√
V 4c b2 g2 4z 2
(12.24)
C F a
(12.25)
F
FIGURE 12.22
Trapezoidal open channel.
TLFeBOOK
40816_12b_p432-450 p434
10/22/01
12:52 PM
Page 435
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p435
HYDRAULICS AND WATERWORKS FORMULAS
435
The discharge through the channel is then ) Q )
√
g
(12.26)
Then, the minimum specific energy and critical depth are Hm
f l n h
(b zDc)3 3/2 Dc b 2zDc
Dc
3b 5zDc D 2b 4zDc c
4zHm 3b √16z 2H 2m 16zHm b 9b 2 10z
(12.27)
(12.28)
Circular Channels
)
Figure 12.23 shows a typical circular channel in which the area a, top width T, and depth Dc are a
)
d2 1 ( r sin 2 ) 4 2
T d sin Dc
d (1 cos ) 2
(12.29) (12.30) (12.31)
Flow quantity is then given by 1 sin 2 )3/2 2 D5/2 Q c 8(sin )1/2 (1 cos )5/2 23/2g1/2( r
(12.32) TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 436
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p436
436
FIGURE 12.23
4081
CHAPTER TWELVE
Circular channel.
F
WEIRS A weir is a barrier in an open channel over which water flows. The edge or surface over which the water flows is called the crest. The overflowing sheet of water is the nappe. If the nappe discharges into the air, the weir has free discharge. If the discharge is partly under water, the weir is submerged or drowned.
a o t u c o s
Types of Weirs A weir with a sharp upstream corner or edge such that the water springs clear of the crest is a sharp-crested weir (Fig. 12.24). All other weirs are classed as weirs not sharp crested. Sharp-crested weirs are classified according to the shape of the weir opening, such as rectangular weirs, triangular or V-notch weirs, trapezoidal weirs, and parabolic weirs. Weirs not sharp crested are classified according to the shape of their cross section, such as broad-crested weirs, triangular weirs, and (as shown in Fig. 12.25) trapezoidal weirs. TLFeBOOK
F
40816_12b_p432-450 p436
10/22/01
12:52 PM
Page 437
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p437
HYDRAULICS AND WATERWORKS FORMULAS
FIGURE 12.24
r s e s
437
Sharp-crested weir.
The channel leading up to a weir is the channel of approach. The mean velocity in this channel is the velocity of approach. The depth of water producing the discharge is the head. Sharp-crested weirs are useful only as a means of measuring flowing water. In contrast, weirs not sharp crested are commonly incorporated into hydraulic structures as control or regulation devices, with measurement of flow as their secondary function.
t r p e r . e r FIGURE 12.25
Weir not sharp crested.
TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 438
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p438
438
4081
CHAPTER TWELVE
FLOW OVER WEIRS Rectangular Weir The Francis formula for the discharge of a sharp-crested rectangular weir having a length b greater than 3h is
Q 3.33
b 10nh [(h h ) 0
3/2
h3/2 0 ] T T 6
where Q discharge over weir, ft3/s (m3/s) b length of weir, ft (m) h vertical distance from level of crest of weir to water surface at point unaffected by weir drawdown (head on weir), ft (m) n number of end contractions (0, 1, or 2) h0 head of velocity of approach [equal to v20 /2gc, where v0 velocity of approach, (ft/s (m/s)], ft (m) gc 32.2 (lb mass) (ft)/(lb force) (s2)(m/s2) If the sides of the weir are coincident with the sides of the approach channel, the weir is considered to be suppressed, and n 0. If both sides of the weir are far enough removed from the sides of the approach channel to permit free lateral approach of water, the weir is considered to be contracted, and n 2. If one side is suppressed and one is contracted, n 1. TLFeBOOK
T T t c c
w t c
B T
40816_12b_p432-450 p438
10/22/01
12:52 PM
Page 439
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p439
HYDRAULICS AND WATERWORKS FORMULAS
439
TABLE 12.2 Discharge of Triangular Weirs Notch (vertex) angle
Discharge formula†
90° 60° 30°
Q 0.685h2.45 Q 1.45h2.47 Q 2.49h2.48
d †
h is as defined above in the Francis formula.
Triangular Weir The discharge of triangular weirs with notch angles of 30°, 60°, and 90° is given by the formulas in Table 12.2.
o r
, ,
Trapezoidal (Cipolletti) Weir The Cipolletti weir, extensively used for irrigation work, is trapezoidal in shape. The sides slope outward from the crest at an inclination of 1:4, (horizontal/vertical). The discharge is Q 3.367bh3/2 where b, h, and Q are as defined earlier. The advantage of this type of weir is that no correction needs to be made for contractions.
e , d l , ,
Broad-Crested Weir The discharge of a broad-crested weir is Q Cbh3/2 TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 440
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p440
440
4081
CHAPTER TWELVE
d t s
TABLE 12.3 Variations in Head Ratio and Coefficient of Discharge for Broad-Crested Weirs Ratio of actual head to design head
Coefficient of discharge
0.20 0.40 0.60 0.80 1.00 1.20 1.40
3.30 3.50 3.70 3.85 3.98 4.10 4.22
t b A p
w Values of C for broad-crested weirs with rounded upstream corners generally range from 2.6 to 2.9. For sharp upstream corners, C generally ranges from 2.4 to 2.6. Dam spillways are usually designed to fit the shape of the underside of a stream flowing over a sharp-crested weir. The coefficient C for such a spillway varies considerably with variation in the head, as shown in Table 12.3. Q, b, and h are as defined for rectangular weirs.
PREDICTION OF SEDIMENT-DELIVERY RATE Two methods of approach are available for predicting the rate of sediment accumulation in a reservoir; both involve predicting the rate of sediment delivery. One approach depends on historical records of the silting rate for existing reservoirs and is purely empirical. The second general method of calculating the sedimentTLFeBOOK
f v t ( a
40816_12b_p432-450 p440
10/22/01
12:52 PM
Page 441
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p441
441
HYDRAULICS AND WATERWORKS FORMULAS
delivery rate involves determining the rate of sediment transport as a function of stream discharge and density of suspended silt. The quantity of bed load is considered a constant function of the discharge because the sediment supply for the bed-load forces is always available in all but lined channels. An accepted formula for the quantity of sediment transported as bed load is the Schoklitsch formula:
Gb
86.7 3/2 S (Qi bqo) D1/2 g
where Gb total bed load, lb/s (kg/s) m m s f t n
Dg effective grain diameter, in (mm) S slope of energy gradient Qi total instantaneous discharge, ft3/s (m3/s) b width of river, ft (m) qo critical discharge, ft3/s (m3/s) per ft (m), of river width (0.00532/S4/3)Dg
e e e . -
An approximate solution for bed load by the Schoklitsch formula can be made by determining or assuming mean values of slope, discharge, and single grain size representative of the bed-load sediment. A mean grain size of 0.04 in (about 1 mm) in diameter is reasonable for a river with a slope of about 1.0 ft/mi (0.189 m/km). TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 442
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p442
442
4081
CHAPTER TWELVE
EVAPORATION AND TRANSPIRATION The Meyer equation, developed from Dalton’s law, is one of many evaporation formulas and is popular for making evaporation-rate calculations:
A l M
M F
E C (ew ea) 1 0.1w
T h
where E evaporation rate, in 30-day month C empirical coefficient, equal to 15 for small, shallow pools and 11 for large, deep reservoirs
w
ew saturation vapor pressure, in (mm), of mercury, corresponding to monthly mean air temperature observed at nearby stations for small bodies of shallow water or corresponding to water temperature instead of air temperature for large bodies of deep water ea actual vapor pressure, in (mm), of mercury, in air based on monthly mean air temperature and relative humidity at nearby stations for small bodies of shallow water or based on information obtained about 30 ft (9.14 m) above the water surface for large bodies of deep water
C C
w monthly mean wind velocity, mi/h (km/h), at about 30 ft (9.14 m) aboveground wind factor
w TLFeBOOK
40816_12b_p432-450 p442
10/22/01
12:52 PM
Page 443
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p443
HYDRAULICS AND WATERWORKS FORMULAS
e g
443
As an example of the evaporation that may occur from a large reservoir, the mean annual evaporation from Lake Mead is 6 ft (1.82 m).
METHOD FOR DETERMINING RUNOFF FOR MINOR HYDRAULIC STRUCTURES The most common means for determining runoff for minor hydraulic structures is the rational formula:
, s
Q CIA where Q peak discharge, ft3/s (m3/s)
, l o e
C runoff coefficient percentage of rain that appears as direct runoff I rainfall intensity, in/h (mm/h) A drainage area, acres (m2)
n e r n ) f
COMPUTING RAINFALL INTENSITY Chow lists 24 rainfall-intensity formulas of the form: I
t where
KF n1 (t b) n
I rainfall intensity, in/h (mm/h) TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 444
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p444
444
CHAPTER TWELVE
K, b, n, and n1 coefficient, factor, and exponents, respectively, depending on conditions that affect rainfall intensity F frequency of occurrence of rainfall, years t duration of storm, min time of concentration Perhaps the most useful of these formulas is the Steel formula: I
K tb
where K and b are dependent on the storm frequency and region of the United States (Fig. 12.26 and Table 12.4). The Steel formula gives the average maximum precipitation rates for durations up to 2 h.
FIGURE 12.26 formula.
Regions of the United States for use with the Steel
TLFeBOOK
4081
445
4 10 25
206 30 247 29 300 36 327 33
140 21 190 25 230 29 260 32
106 17 131 19 170 23 230 30
70 13 97 16 111 16 170 27
70 16 81 13 111 17 130 17
68 14 75 12 122 23 155 26
32 11 48 12 60 13 67 10
TLFeBOOK
Page 445
K b K b K b K b
12:52 PM
7
10/22/01
6
l
2
Coefficients
40816_12b_p432-450
5
Region Frequency, years
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p445
4
p444
t
3
:
s
d
2
-
1
TABLE 12.4 Coefficients for Steel Formula
40816_12b_p432-450
10/22/01
12:52 PM
Page 446
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p446
446
4081
CHAPTER TWELVE
GROUNDWATER
w p
Groundwater is subsurface water in porous strata within a zone of saturation. It supplies about 20 percent of the United States water demand. Aquifers are groundwater formations capable of furnishing an economical water supply. Those formations from which extractions cannot be made economically are called aquicludes. Permeability indicates the ease with which water moves through a soil and determines whether a groundwater formation is an aquifer or aquiclude. The rate of movement of groundwater is given by Darcy’s law:
F T u
w
Q KIA where Q flow rate, gal/day (m3/day) K hydraulic conductivity, ft/day (m/day) I hydraulic gradient, ft/ft (m/m) A cross-sectional area, perpendicular to direction of flow, ft2 (m2)
WATER FLOW FOR FIREFIGHTING
T g
The total quantity of water used for fighting fires is normally quite small, but the demand rate is high. The fire demand as established by the American Insurance Association is G 1020 √P (1 0.01√P) TLFeBOOK
40816_12b_p432-450 p446
10/22/01
12:52 PM
Page 447
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p447
447
HYDRAULICS AND WATERWORKS FORMULAS
where G fire-demand rate, gal/min (liter/s); and P population, thousands. n e m d s y
FLOW FROM WELLS The steady flow rate Q can be found for a gravity well by using the Dupuit formula: Q
1.36K(H 2 h2) log(D/d)
where Q flow, gal/day (liter/day) K hydraulic conductivity, ft/day (m/day), under 1:1 hydraulic gradient H total depth of water from bottom of well to free-water surface before pumping, ft (m) n
h H minus drawdown, ft (m) D diameter of circle of influence, ft (m) d diameter of well, ft (m) The steady flow, gal/day (liter/day), from an artesian well is given by
y s
Q
2.73Kt(H h) log(D/d)
where t is the thickness of confined aquifer, ft (m). TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 448
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p448
448
4081
CHAPTER TWELVE
ECONOMICAL SIZING OF DISTRIBUTION PIPING An equation for the most economical pipe diameter for a distribution system for water is D 0.215
S f bQ aiH 3 a
1/7
a
where D pipe diameter, ft (m) f Darcy–Weisbach friction factor
F
b value of power, $/hp per year ($/kW per year) Qa average discharge, ft3/s (m3/s)
w
S allowable unit stress in pipe, lb/in2 (MPa) a in-place cost of pipe, $/lb ($/kg) i yearly fixed charges for pipeline (expressed as a fraction of total capital cost) Ha average head on pipe, ft (m)
VENTURI METER FLOW COMPUTATION
H
Flow through a venturi meter (Fig. 12.27) is given by Q
cKd 22
K
4
H v t a
√h1 h2
√
2g 1 (d 2 d 1) 2 TLFeBOOK
40816_12b_p432-450 p448
10/22/01
12:52 PM
Page 449
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p449
449
HYDRAULICS AND WATERWORKS FORMULAS
a
FIGURE 12.27
)
Standard venturi meter.
where Q flow rate, ft3/s (m3/s) c empirical discharge coefficient dependent on throat velocity and diameter d1 diameter of main section, ft (m)
s
d2 diameter of throat, ft (m) h1 pressure in main section, ft (m) of water h2 pressure in throat section, ft (m) of water
HYDROELECTRIC POWER GENERATION Hydroelectric power is electrical power obtained from conversion of potential and kinetic energy of water. The potential energy of a volume of water is the product of its weight and the vertical distance it can fall: PE WZ TLFeBOOK
40816_12b_p432-450
10/22/01
12:52 PM
Page 450
40816 HICKS Mcghp Ch. 12 REVISE PASS bzm 7/18/01 p450
450
CHAPTER TWELVE
where PE potential energy W total weight of the water Z vertical distance water can fall Power is the rate at which energy is produced or utilized: 1 horsepower (hp) 550 ftlb/s 1 kilowatt (kW) 738 ftlb/s 1 hp 0.746 kW 1 kW 1.341 hp Power obtained from water flow may be computed from hp
#Qwh #Qh 550 8.8
kW
#Qwh #Qh 738 11.8
where kW kilowatt hp horsepower Q flow rate, ft3/s (m3/s) w unit weight of water 62.4 lb/ft3 (998.4 kg/m3) h effective head total elevation difference minus line losses due to friction and turbulence, ft (m) # efficiency of turbine and generator TLFeBOOK
40816_Index_p451-461
10/22/01
12:53 PM
Page 451
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 451
INDEX
Adjustment factors for lumber, 224–233 Allowable-stress design, 285–297
Beam formulas, 16–98 beam formulas and elastic diagrams, 29–39 beams of uniform strength, 63 characteristics of loadings, 52 combined axial and bending loads, 92 continuous beams, 16, 27, 51 curved beams, 82–88 eccentrically curved, 86 eccentric loading, 94–96 elastic-curve equations for prismatic beams, 40–51 elastic lateral buckling, 88–92
natural circular and periods of vibration, 96–98 rolling and moving loads, 79–82 safe loads for beams of various types, 64–78 parabolic beam, 64 steel beam, 66 triangular beam, 65 ultimate strength of continuous beams, 53–62 Castigliano’s theorem, 62 Maxwell’s theorem, 62 unsymmetrical bending, 93 Blasting, vibration control in, 280–282 Bridge and suspension-cable formulas, 322–354 allowable-stress design, 323
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
40816_Index_p451-461
10/22/01
12:53 PM
Page 452
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 452
452
4
INDEX
Bridge and suspension-cable formulas (Continued ) for bridge beams, 325–327 for bridge columns, 323 for shear, 339–340 bearing on milled surfaces, 332 bridge fasteners, 333 cable systems, 353 composite construction in highway bridges, 333 bending stresses, 335 effective width of slabs, 334 shear range, 335–337 span/depth ratios, 334 general relations for suspension cables, 341–352 keeping strength at different levels, 348 parabola, 347 supports at different levels, 348 supports at same level, 349–352 hybrid bridge girders, 329 load-and-resistance factor design, 324–331 for bridge beams, 330–331 for bridge columns, 324–325 maximum width/thickness ratios, 341
Bridge and suspension-cable formulas (Continued ) number of connectors in bridges, 337–339 ultimate strength of connectors, 339 shear strength design for bridges, 322–323 stiffeners on bridge girders, 327 longitudinal stiffeners, 328 suspension cables, 341–352 catenary cable sag, 344 parabolic cable tension and length, 341–344 Building and structures formulas, 284–319 allowable-stress design, 285–297 for building beams, 287–290 for building columns, 285 for shear in buildings, 295–297 bearing plates, 298–300 bents and shear in walls, 304–306 deflections of, 304 column base plates, 300 combined axial compression or tension and bending, 306–307 composite construction, 313–315 TLFeBOOK
B
C C C C C C C C
40816_Index_p451-461 2
10/22/01
12:53 PM
Page 453
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 453
INDEX
Building and structures formulas (Continued ) design of stiffeners under load, 311–312 fasteners in buildings, 312–313 load-and-resistance factor design, 284–294 for building beams, 290–294 for columns, 287 for shear, 284–285 milled surfaces, bearing on, 301 number of connections required, 316–318 shear on connectors, 317 plate girders in buildings, 302–304 ponding considerations, 318–319 stresses in thin shells, 297 webs under concentrated loads, 308–310
Cable systems, 353 California bearing ratio, 274 Cantilever retaining walls, 208–211 Chezy formula, 399 Circular channels, 435 Circular curves, 356–359 Column formulas, 100–130 Columns, lumber, 218–220
453
Commonly used USCS and SI units, 3 Composite construction, 313–315, 333–337 Concrete, formulas for, 148– 212 braced and unbraced frames, 201–202 cantilever retaining walls, 208–211 column moments, 199–200 compression development lengths, 170 continuous beams, 16, 27, 52, 151, 153–162 one-way slabs, 151–153 crack control, 170 deflection, computation for, 172–173 design methods, 153–162 beams, 153–162 columns, 162–167 flat-plate construction, 195–197 direct design method, 195–197 flat-slab construction, 192–195 gravity retaining walls, 205–208 hardened-state properties, 167–168 job mix volume, 148 load-bearing walls, 202–203 modulus of elasticity, 150 TLFeBOOK
40816_Index_p451-461
10/22/01
12:53 PM
Page 454
40816 HICKS Mcghp Index Conf. 8/6/01 p. 454
454
4
INDEX
Concrete, formulas for (Continued ) properties in hardened state, 167–168 reinforced, 148–212 required strength, 171 shear in slabs, 197–199 shear walls, 203–205 spirals, 200–201 tensile strength, 151 tension development length, 169 ultimate-strength design of I and T beams, 186–187 ultimate-strength design of rectangular beams, 173–174 balanced reinforcing, 174 with compression bars, 183–185 development of tensile reinforcement, 177 hooks on bars, 178 moment capacity, 175 ultimate-strength design for torsion, 189–191 wall footings, 211–212 water-cementation ratio, 148 working-stress design: for allowable bending moment, 179 for allowable shear, 180–181 of I and T beams, 187–189
Concrete, formulas for (Continued ) of rectangular beams, 183–185 for torsion, 189–191 Continuous beams, 16, 27, 51, 153–162 Conversion factors for civil engineering, 2–14 Conversion table, typical, 4 Crack control, 170 Culverts, highway, designing, 371–374
Darcy–Weisbach formula, 398 Design methods, 153–167 beams, 153–162 columns, 162–167
Earthmoving formulas, 276–278 Elastic–curve equations for prismatic beams, 40–51 Expansion, temperature, of pipe, 414
Factors, adjustment, for lumber, 224–233 conversion, 2–14 Fasteners, for lumber, 233–236 Fixed-end moments, 52 Flat-plate construction, 195–197 TLFeBOOK
F F
G G
H
40816_Index_p451-461
10/22/01
12:53 PM
Page 455
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 455
INDEX
Flat-slab construction, 192–195 Forest Products Laboratory, 221
Geometric properties of sections, 17–28 Grading of lumber, 214
Highway and road formulas, 356–379 American Association of State Highway and Transportation Officials (AASHTO), 363–365 circular curves, 356–359 equations of, 358 culverts, highway, designing, 371–374 American Iron and Steel Institute (AISI) design procedure, 374–379 allowable wall stress, 376 bolted seams, checking of, 379 handling stiffness, 378 ring compression, 376 wall thickness, 378 highway alignments, 362 curves and driver safety, 361 stopping sight distance, 363–365 stationing, 362
455
Highway and road formulas (Continued ) interchanges, types of, 367 parabolic curves, 359 equations of, 360 street and maneuvering space, 370 structural numbers for flexible pavements, 368–370 transition (special) curves, 370 turning lanes, 368–369 Hydraulic and waterworks formulas, 382–450 capillary action, 382–386 computing rainfall intensity, 443–445 culverts, 417 entrance and exit submerged, 417 on subcritical slopes, 418–420 economical sizing of distribution piping, 448 evaporation and transpiration, 442 flow from wells, 447 flow over weirs, 438 broad-crested weir, 439 rectangular weir, 438 trapezoidal (Cipolletti) weir, 439 triangular weir, 439 TLFeBOOK
40816_Index_p451-461
10/22/01
12:53 PM
Page 456
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 456
456
4
INDEX
Hydraulic and waterworks formulas (Continued ) flow through orifices, 406–409 discharge under falling head, 409 submerged orifices, 408 fluid flow in pipes, 395–403 Chezy formula, 399 Darcy–Weisbach formula, 398 Hazen-Williams formula, 401 Manning’s formula, 401 turbulent flow, 397 fluid jets, 409 forces due to pipe bends, 414–416 fundamentals of fluid flow, 388–392 groundwater, 446 hydraulic jump, 425–429 hydroelectric power generation, 449–450 Manning’s equation for open channels, 424 method for determining runoff, 443 nonuniform flow in open channels, 429–435 circular channels, 435 parabolic channels, 433 rectangular channels, 430 trapezoidal channels, 434 triangular channels, 431
Hydraulic and waterworks formulas (Continued ) open-channel flow, 420–423 critical depth of flow, 423 normal depth of flow, 423 orifice discharge, 410 pipe stresses, 412–413 prediction of sediment delivery rate, 440 pressure changes caused by pipe size changes, 403–404 bends and standard fitting losses, 405 gradual enlargements, 404 sudden contraction, 404 similitude for physical models, 392–395 submerged curved surfaces, pressure on, 387–388 temperature expansion of pipe, 414 venturi meter flow computation, 448 viscosity, 386 water flow for firefighting, 446 water hammer, 412 weirs, 436–439 types of, 436–437
Load-and-resistance factor design, 284–294, 324–331 TLFeBOOK
L
L L
40816_Index_p451-461 6
10/22/01
12:53 PM
Page 457
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 457
457
INDEX
Load-and-resistance factor design (Continued ) for bridge beams, 330–331 for bridge columns, 324–325 for building beams, 290–294 for building columns, 287 for building shear, 284–285 Load-bearing walls, 202–203 Lumber formulas, 214–241 adjustment factors for design values, 224–233 beams, 215–218 bearing area, 229 bending and axial compression, 240 bending and axial tension, 239 column stability and buckling, 230–233 for connections with fasteners, 236–238 columns, 218–220 in combined bending and axial load, 220 compression, at angle to grain, 220 on oblique plane, 223–224 fasteners for lumber, 233 nails, 233 screws, 234–236 spikes, 233 Forest Products Laboratory recommendations, 221–222 grading of lumber, 214
Lumber formulas (Continued ) radial stresses and curvature, 236–238 size and volume of lumber, 227
Manning’s formula, 401 Maxwell’s theorem, 62 Modulus of elasticity, 150
Open channels, nonuniform flow in, 429–435 Orifice discharge, 410 Orifices, flow through, 406–409
Parabolic channels, 433 Piles and piling formulas, 132–146 allowable load, 132 axial-load capacity, single piles, 143 foundation-stability and, 139–143 groups of piles, 136–139 laterally loaded, 133 shaft resistance, 145 shaft settlement, 144 toe capacity load, 134–135 Pipe bends, 414–416 Pipes, flow in, 395–403 TLFeBOOK
40816_Index_p451-461
10/22/01
12:53 PM
Page 458
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 458
458
INDEX
Piping, economical sizing of, 448 Plate girders in buildings, 302–304 Ponding, roof, 318–319 Prismatic beams, elastic-curve equations for, 40–51
Rainfall intensity, computing, 443–445 Rectangular channels, 430 Retaining walls, forces on, 265 Road formulas, 356–379 Rolling and moving loads, 79–82 Roof slope to avoid ponding, 238–239
Safe loads for beams, 64–78 Sections, geometric properties of, 17–28 Sediment, prediction of delivery rate, 440 Similitude, physical models, 392–395 Sizes of lumber, 214–215 Soils and earthwork formulas, 258–282 bearing capacity of, 270 California bearing ratio, 274 cohesionless soils, lateral pressure in, 266
4
Soils and earthwork formulas (Continued ) cohesive soils, lateral pressure in, 267 compaction equipment, 275 compaction tests, 272 load-bearing, 273 earthmoving formulas, 276–278 quantities hauled, 278 forces on retaining walls, 265 index parameters, 259–260 internal friction and cohesion, 263 lateral pressures, 264 permeability, 274 physical properties of soils, 258 scraper production, 278 equipment required, 278 settlement under foundations, 271 stability of slopes, 269 cohesionless soils, 269 cohesive soils, 269 surcharge lateral pressure, 268 vertical pressures, 264 vibration control in blasting, 280–282 water pressure and soils, 268 weights and volumes, relationships of, 261–262 TLFeBOOK
S S S
S
T T T
40816_Index_p451-461 8
10/22/01
12:53 PM
Page 459
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 459
INDEX
Strength, tensile, 151 Submerged curved surfaces, 387–388 Surveying formulas, 244–256 distance measurement with tapes, 247–250 orthometric correction, 251–252 photogrammetry, 255–256 slope corrections, 250 stadia surveying, 253–255 temperature corrections, 250 theory of errors, 245–247 units of measurement, 244 vertical control, 253 Suspension cables, 341–352
Table, conversion, 4 Temperature expansion of pipe, 414 Thin shells, 297
459
Timber engineering, 214–241 Trapezoidal channels, 434 Triangular channels, 431
Ultimate strength, of continuous beams, 53–62 Uniform strength, of beams, 63
Venturi meter flow computations, 448 Vibration, natural circular and periods of, 96–98 Viscosity, 386
Walls, load bearing, 202–203 Water flow for firefighting, 446 Weirs, 436–439 Wells, flow from, 447
8
TLFeBOOK
This page intentionally left blank.
TLFeBOOK
40816_Index_p451-461 0 Blank
10/22/01
12:53 PM
Page 461
40816 HICKS Mcghp Index Second Pass 7/25/01 p. 461
ABOUT THE AUTHOR Tyler G. Hicks, P.E., is a consulting engineer and a successful engineering book author. He has been involved in plant design and operation in a multitude of industries, has taught at several engineering schools, and has lectured both in the United States and abroad. Mr. Hicks holds a Bachelor’s Degree in Mechanical Engineering from Cooper Union School of Engineering in New York.
TLFeBOOK Copyright 2002 The McGraw-Hill Companies. Click Here for Terms of Use.
