О
М О СКВА «НИВА РОССИИ» 1992
Б Б К 85.125 Т66 У Д К 645.5
Трапезников Ф . Ф . Т 6 6 Плетение ивового прута и берес...
125 downloads
491 Views
15MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
О
М О СКВА «НИВА РОССИИ» 1992
Б Б К 85.125 Т66 У Д К 645.5
Трапезников Ф . Ф . Т 6 6 Плетение ивового прута и бересты.— М .: Нива России, 1992.— 192 с., илл. 18ВК 5-260-00577-5 Практическое пособие по плетению изделий из ивового прута и бересты знакомит с технологией заготовки, подготовки, обработки материала, техникой и видами плетения предметов бытового и художественного назначения. Особое внимание уделено правильному пользованию инструментами, а также изготовле нию их своими руками. Рассчитано на широкий круг читателей, может служить учебным пособием для коллективных и индивидуальных занятий.
Т
3701000000 - 011 М104(03) — 92 77“ 91
ВЕК 85 124 ББК 85.125
И зда н и е дл я досуга
Федор Федорович Трапезников ПЛЕТЕНИЕ ИВОЬОГО ПРУТА И БЕРЕСТЫ Литературная запись О. Ч. Пет ровых Зав. редакцией Г. Л. Бондарева. Редактор О. Ч. Петровых. Младший редактор Д. М. Шишляева. Х удож ник И. М. Гурьев. Художественный редактор Г. Л. Шацкий. Технические редакторы А . А. Айсина, Т. Н. Каж дом. Корректор Л. А. Балашова
ИБ№ 3169 Сдано в набор 15.03.91. Подписано в печать 22.11.91. Формат 6 0Х 9 0 '/ 16- Бумага офс. № 1. Гарнитура академическая. Печать офсетная. Уел. печ. л. 12,0. Уел. кр.-отт. 24,25. Уч.-изд. л. 12,84. Тираж 100 000 экз. Заказ № 2852. Изд. № 1647. Издательство «Нива России», 117218, Москва, ул. Кржижановского д. 15, корп. 2 Смоленский полиграфкомбинат Министерства печати и массовой информации Российской Федерации. 214020, Смоленск, ул. Смольянинова, 1.
18В Ы
5 -2 6 0 -0 0 5 7 7 -5
© © ©
Ф . Ф . Трапезников, автор текста, 1992. О . Ч. Петровых, литературная запись, 1992. С. А . Седлер, фотоиллюстрации, 1992.
\]
к ш ВС
ел< кл ж; е <
и искусными изделиями славились мастера Верхнего Поволжья: кустари из Кинешмы, умельцы из Костромской л Ивановской губерний. Этим подсобным промыслом были заняты десятки тысяч крестьян, а в ряде мест плетение стало одним из распространенных ремесел. Развитию промыслов способствовала организация школ, в которых обучали плетению. Одна из первых школ в России была открыта в конце 80-х гг. прошлого столетия вблизи станции Пушкино Ярославской железной дороги (ныне город К расноармейск). Такие школы были открыты в Полтаве, Киеве, Черкассах, под К урском и других городах России. Одним из наиболее крупных центров плетения бы ло село Большие Вяземы З венигородского уезда М осковской губернии, где развитию промысла способствовал местный помещик князь Д . В. Голицын, который ввел плетение корзин и других изделий из очищенных прутьев, а в последствии здесь бы ло освоено плетение мебели. В 90-е гг. прошлого столетия организуется земская учебная мастерская на ст. Голицыно М осковской железной дороги. В мастерской обучали местных кустарей выработке модных изделий по отече ственным образцам и руководствам, а также по книгам, изданным в Лондоне, Вене, Париже и других городах мира. Все это позволило значительно усовершенствовать технику и технологию изготовления изделий, улучшить их внешний вид, сделать их более прочными. Лучшие работники этой мастерской участвовали в международных выставках, завоевав всеобщее признание, они неоднократно полу чали призы. В начале X X в. французские мастера стали использовать в работе тонкую окоренную лозу, покры тую различными красителями, позоло той, серебром. М ода на такие изделия привлекла внимание и мастеров России. Все сырье стали специально обрабатывать (отбеливать, красить в различные цвета). В работе они сочетали окрашенные и неокрашенные материалы. Появились корзинки, покрытые масляными красками и расписанные по фону орнаментом, цветами и т. д. Большой спрос на эту изящ ную продукцию позволил кустарям-корзинщикам в 1899 г. создать первую в России артель с центром в Больших Вяземах, яд ром которой стала учебная мастерская М осковского губернского земства. А ссортим ент товаров в начале X X в. был очень велик: всевозмож ная мебель (стулья, столы, кресла, диваны, ширмы, этажерки, детские кроватки ); газетницы, коляски, качели, дорожные принадлежности (сундуки, чемоданы, саквояжи, су м ки ); корзиночки самого различного назначения (для бумаг, рукоделия, цветов и фруктов, хлебницы, сухарницы ); всевозможные детские игрушки и т. д. В наши дни плетеными изделиями пользуются, конечно же, реже, чем в древние времена. Важное место занимают корзины — они незаменимы при сборе и транспортировке овощей и фруктов, при хранении продукции сельского хозяйства, не могут обойтись без корзин грибники. К сожалению, многие другие плетеные изделия уже не имеют 4
такого больш ого практического значения или даже незаслуженно забыты. Действительно, гораздо полезнее вывозить ребенка на прогулку в легкой и прочной коляске, сплетенной из ивового прута, нежели в выполненной из синтетических материалов. Легкая и удобная плетеная мебель очень украсит как садовый участок, так и гостиную дома. Такая мебель была бы очень удобна, например, для открытых кафе, детских учреждений и т. д. М ож н о и дальше перечислять множество вариантов использования легких, удобных, недорогих плетеных изделий, доказывать их преимущество, но лучше убеждать в своей правоте не словом, а делом, чем и Занята многочисленная армия людей, увлеченных плетением. Причем этим интересным делом заняты как профессиональные плетельщики — работники лесхозов, так и самодеятельные любители. В настоящее время в производственной сфере важное место занимают Черниговская фабрика лозовы х изделий, Ереванский лесхоз, С орокский мехлесхоз М олдовы, Д зерж инский лесхоз Н иж егородской области и другие предприятия, занятые выпуском изделий из ивового прута. П очти все лесхозы изготавливают из неокоренного прута корзинки для нужд сельского хозяйства, а из очищенного — хозяйственно бытовые, фруктово-ягодные, цветочные и подарочные. Н екоторы е лесхозы освоили выпуск плетеной мебели — столов, кресел, стульев, диванов. В системе М инистерства местной промышленности Р С Ф С Р более сорока предприятий выпускают плетеные изделия: мебель, корзины, сумки, хлебницы, кашпо и др. Н ельзя не отметить Ивантеевский селекционный опытно-показательный питомник В сесою зного научно-исследовательского института лесоводства и механизации лесного хозяйства. В последние годы здесь внедрены в производство различные механизмы и приспособления, разработан и освоен выпуск ш ирокого ассортимента плетеных изделий, что позволило питомнику стать одним из первых показательных хозяйств. Большой вклад в развитие древнего промысла вносят самодеятель ные плетельщики. Работы многих из них можно назвать настоящими произведениями искусства. Традиционным смотром народных талантов завершился второй В сесоюзный фестиваль народного творчества, посвященный 70-летию Великой О ктябрьской социалистической революции на В Д Н Х С С С Р в М оскве. З десь можно бы ло увидеть самые разнообразные экспонаты, выполненные из ивового прута и других растительных материалов известными профессиональными мастерами и любителями худож е ственного плетения из Р С Ф С Р , Украины и Белоруссии, Средней А зи и , Закавказья и Прибалтийских республик. Участие в прошедшем фестивале рабочих, колхозников, студентов, школьников, ветеранов войны и труда является характерным показателем степени демократиза ции культурной жизни нашей страны.
Основные породы дикорастущих ив Основны м материалом для плетения изделий являются одно двухлетние побеги ивы. На территории С С С Р насчитывается более 100 видов ивы, но не все они пригодны для плетения. Вот некоторые дикорастущие породы, которые рекомендуются для изготовления плетеных изделий. Ива пурпурная (красноцветная, краснотал) — ветвистый кустарник вы сотой 1— 3 м, произрастает в средней полосе и на юге страны. Предпочитает долины рек, прибрежные пески, канавы и луга. Растет как на влажных, так и на сухих почвах. Кора блестящая, красного цвета, с темно-красным и коричневым оттенком. Ветви пурпурные или жел тые, голые, блестящие. Листья ланцетовидные, сверху темно-зеленые, снизу сизо-зеленые. Для плетения изделий использую т две формы ивы пурпурной — Ламберта и уральскую. И в а Л а м б е р т а — крупная с большими листьями и сильными побегами. Растет бы стро, однолетние побеги иногда достигают 2 м. Крупные прутья идут на изготовление мебели и других крупных изделий, мелкие — гибкие и прочные, имеют мало сучков, они пригодны для плетения всевозмож ны х поделок. И в а у р а л ь с к а я — кустарник высотой 4 м с тонкими побегами. П рутья тонкие, гибкие, с маленькой сердцевиной, хорош о очищаются от коры. После проварки приобретают бронзовы й оттенок. Не уменьшает урожая при ежегодной срезке прута. Является превосходным материалом для плетения самых изящных изделий. Ива трехтычинковая (белотал, белолаз) распространена по всей европейской части С С С Р , в Сибири, Закавказье и на Дальнем Востоке. П роизрастает в поймах рек, на молодых наносах и островках. Известны две формы ивы трехтычинковой — одноцветная и двухцветная. И в ы о д н о ц в е т н а я (листья сверху и снизу зеленые) и д в у х ц в е т н а я (сверху листья зеленые, снизу си зы е). П обеги их тонкие, гибкие, желтовато-зеленые, с маленькой сердевиной, листья продолго ватые, длина их в 3 раза больше ширины. Цветет с апреля по май, после распускания листьев. Неочищенный прут пригоден для плетения всех видов корзин хозяйственного назначения, а очищенные круглые или расколотые прутья — для всевозмож ных изделий. Ива козья — большой куст или дерево высотой 6— Ю м. Распростра нена на всей территории С С С Р . П роизрастает на влажных и свежих незаболоченных почвах, на лесных опушках, вдоль дорог и канав. К ора гладкая, зеленовато-серая. Л истья овальной формы с зубчатым краем, сверху темно-зеленые, снизу сероватые. Отличается бы стры м ростом, после обрезки дает много сильных побегов, пригодных для простого плетения, является хорошим материалом для каркасов. Ива лавролистная (чернотал, ракитник) — дерево высотой до 13 м, ш ироко распространено на территории С С С Р . Кора на молодых побегах темно-красного цвета. Л истья продолговато-овальные с зазубринами на 6
краях, верхняя сторона блестящая, темно-зеленая, нижняя — матовая, бледная. Древесина очень прочная, трудно раскалывается. К ору снимают с прутьев, срезанных в период сокодвижения. М олоды е побеги употребляют при плетении изделий из зеленого прута. Ива остролистная (шелюга красная) — кустарник высотой до 6— 8 м, распространена на всей европейской части С С С Р (кром е Арктики, Крыма и Закавказья), одна из наиболее часто встречающихся ив в стране, произрастает в речных долинах, образуя большие заросли. Цвет коры молодых побегов темно-красный или красно-бурый. Листья узкие, длинные, с зубчатым краем, сверху блестящие, снизу зеленоватые, черенки длинные. П рутья тонкие, хорош о гнутся, пригодны для мелкого плетения. К ора горькая; если прутья не окорены, горечь передается на фрукты и ягоды, поэтому для плетения корзин непригодна.
Выращивание ивы В плетении можно использовать не только дикорастущие ивы, но и культурные растения. Эти деревья и кустарники выращивают на приусадебных участках, в коллективных садах. Выращивание ивы на своем участке позволяет получить материал нужного качества и сэкономить время на заготовку прутьев, при этом любитель может культивировать наилучшие сорта. Коллектив учащихся курсов или кружков может заложить целый сад, который не только обеспечит их материалом, но и будет способствовать озеленению города или поселка. Площадь под плантацию выбирают ровную, без застойных вод. При подготовке к посадке участок разравнивают и очищают от растительных остатков. Ива хорош о растет на глиняных и песчаных почвах, где ф ормиру ются гибкие с маленькой сердцевиной прутья, а на богатых перегноем — длинные и толстые. При закладке плантации используют черенки одно- и двухлетних побегов, взятых от лучших сортов кустарниковых видов ивы. Побеги должны бы ть ровными, без повреждений. Черенки нарезают только из срединно-комлевой части, так как из вершинной части черенки плохо приживаются, боковые прутья не используют. Длина (2 0 — 40 см ) и толщина (0 ,5 — 2 см ) черенков зависит от местности, в которой идет посадка, от сорта и вида ивы. Посадочный материал заготавливают непосредственно перед посад к о й — осенью (после опадания листьев) и весной (д о начала сокодвиж ен ия). Д ля выращивания ивы на тонкий прут черенки высаживают на расстоянии 30— 40 см друг от друга. При посадке ряды маркируют по шнуру. Э ту работу лучше выполнять вдвоем: один делает в почве углубление, равное длине черенка, второй вставляет в углубление 7
черенки, следя за тем, чтобы на поверхности почвы оставался один глазок — почка, и ногой уплотняют землю вокруг черенка. О дна из важнейших работ по уходу за посадками — рыхление почвы. Кроме того, необходимо уничтожение сорняков. На местах неприжившихся черенков проводят дополнительную посадку в те же сроки (осен ью и ранней весной). При благоприятных условиях, хорошем уходе за плантациями заготавливать прут можно осенью первого года; массовую заготовку прута начинают со второго года. При рациональном использовании посадки можно эксплуатировать в тече ние 12— 15 лет, затем их полностью вырубают. И з оставшихся небольших пней вырастают новые ивовые побеги. Д ля посадки рекомендуются ива пурпурная, трехтычинковая, а также культивируемые — кустарник американской ивы, дающий длинный, тонкий прут; гибриды пурпурной и трехтычинковой; козьей и трехтычинковой, имеющие отличную древесину, и другие разновидно сти. Такие сорта ив можно приобрести в лесхозах М осковской, Рязанской, Тульской, Калининградской, Ивановской областей и ряда сою зны х республик. Т от, кто желает получить более исчерпывающие сведения, может посетить один из ближайших питомников, где выращивают иву, и там ознакомиться с особенностями развития ивовых кустов.
Заготовка ивовых прутьев Прежде чем приступить к плетению, необходимо научиться правильно заготавливать прутья; определить места, где произрастает ива, наилучшее время срезки, кроме того, очень важно уметь обрабатывать и хранить материал. Начинающему плетельщику для регулярных занятий на зиму необходимо заготовить 3— 3,5 тыс. штук прутьев разных размеров: длиной от 400 до 1200 мм, диаметром 2— 5 мм (диаметр определяется у основания прута). Э ти цифры ориентировочные, и только практический опыт дает возмож ность определить, какой прут надо заготавливать, а впослед ствии и применять в том или другом изделии, но в любом случае прут выбирают длинный, ровный, без резкого перепада толщины — с наименьшим конусом, от прироста прошлого и текущего года, т. е. одно-двухлетний побег. Ивы, пригодные для срезки, растут всюду — по берегам водоемов, в оврагах, даже на обочинах дорог. Н о лучшие естественные заросли — ивняки, располагаются по берегам рек с быстрым течением, там, где есть большие наносы песка (пляж и и песчаные отмели). Прутья этих растений отличаются особой прочностью, упругостью , гибкостью и эластичностью. В этих местах развивается не очень большой кустарник, но благодатные условия, в которых он растет, обилие влаги 8
и солнца дают возмож ность ему бы стро размножаться и позволяют получать прутья для самого изящного плетения. Ивовые прутья заготавливают в разное время года: весной в начале роста прута (когда распускаются почки), летом, в конце его роста (ию ль — а вгуст); осенью после полного созревания прута, когда листья начинают желтеть и опадать, и зимой до начала весеннего разбухания почек. Весенне-летняя заготовка прутьев называется соковой, или вегета ционной. В это время очищенный прут имеет очень красивую молочнобелую окраску. К ора с прутьев очищается легко при помощи щемилки и не требует дополнительной обработки. Н о у прутьев, срезанных в это время, древесина еще не достигает достаточной и равномерной зрелости, макушки могут быть травянистыми, побеги не очень гибкие и часто ломаются. К роме тонких прутьев, летом желательно заготовить толстые для обручей, ручек и каркасов. В осенне-зимний период заготовки прутья обладают крепкой, гибкой, эластичной древесиной, покрыты прочной корой для зеленого плетения. Период заготовки длится 4— 5 месяцев. В это время можно получить материал с цветным оттенком и, следовательно, использовать в работе неошкуренные — красные, темно-красные, зеленые, желтые, серые прутья, которые пригодны для отделки и расцветки изделий. При заготовке прутьев необходимо соблю дать определенные правила. С резку надо проводить с наклоном для стока воды с пенька. Высота пенька может быть от 10 до 30 см; это зависит от местности, где режут прут — в заболоченных местах пеньки оставляют больших размеров. Чем больше срезаю т прутьев, тем больше вырастает новых побегов. Н о это не значит, что ивовые кустарники надо безж алостно резать. Х озяй ск ое, бережное отношение к природе долж но проявляться с первых прикосновений к ивовому пруту. Выезжая на заготовку материала, каждый начинающий плетельщик должен иметь: щемилку (см . рис. 7 ), нож, полиэтиленовую пленку, бечевку, перчатки, аптечку. Очень хорош о, если плетельщик заведет дневник, в котором следует отмечать дату, место заготовки прутьев, какая была погода в день заготовки и в течение сезона (например, ранняя или поздняя весна, дождливое ли лето и т. п .). Техника безопасности при заготовке ивового прута. Плетельщик должен уметь пользоваться острым ножом. Срезая прутья с прош ло годних пеньков, нож направляют от себя, при этом надо быть осторож ным, чтобы не наколоть руку о сухой пенек.
Обработка прутьев, заготовленных в весенне-летний период Очистка от коры. Нарезав определенное количество прутьев, приступают к окоренению. Э ту операцию проводят в два приема. П е р в ы й п р и е м . Справа кладут прутья макушками к себе, чтобы удобно бы ло брать их за верхнюю часть. После чего вставляют комлевый конец до половины прута в прорезь (расщ еп ) щемилки, конец которой втыкают в землю. Затем левой рукой слегка прижимают верх щемилки, правой протягивают весь комлевый конец прута через ее сжатое отверстие. При этом кора отстает от древесины на утолщенном конце прута. Н е следует прижимать щемилку очень крепко, так как она может повредить древесину. Если пользуются щемилкой в помещении, то ее можно закрепить в тиски или вколотить в чурбан. В этом случае работают стоя. Второй п р и е м . П рутья кладут с правой стороны, только комельками к себе. Надевают перчатки из лю бого материала, кроме кожаных, чтобы руки не скользили от обилия сока. Правой рукой берут прут за комель, кладут его в левую руку между большим и указатель ным пальцами и снимают кору с верхней части, выдергивая прут на себя правой рукой. Очистка прутьев таким способом ускоряет работу в 2— 3 раза. Э тот прием можно выполнять и щемилкой. И з свежесрезанных, очищенных и отмоченных в воде прутьев можно сразу заготовить обручи. Как это сделать, рассказано ниже. Сушка окоренных ивовых прутьев. После окоренения прутьев их надо немедленно (зд есь же на месте заготовки) высуш ить на солнце. Окоренные 80 — 100 прутьев раскладывают тонким слоем на настил, кладут или приставляют к жердям (рис. 1) и периодически переворачи вают их до полного высыхания. Летом в солнечный день для этого достаточно 5— 6 ч. Во время сушки прутья оберегают от дождя, накрывая полиэтиленовой пленкой. В дож дливую или пасмурную погоду прутья сушат в хорош о проветриваемом помещении или под навесом, при этом их надо как можно чаще переворачивать, иначе недосушенные прутья потемнеют или приобретут пятнистую окраску. Высушенные прутья связывают в пучки. Предварительно их сортирую т по длине и толщине, что намного облегчит дальнейшую работу. Пучки прутьев обязательно маркируют — отмечают дату и место заготовки (ри с. 2 ).
Рис. 1. Сушка окоренных прутьев: а — на настиле; 6 — приставленными к жердям
Обработка прутьев, заготовленных в осенне-зимний период Материал, заготовленный в осенне-зимний период, требует дополнительной обработки. Перед окоренением прутья кипятят в воде, после чего кору снимают щемилкой. Д ля проварки прутьев берут металлический бак или котел. Если есть возмож ность, лучше заказать специальную ванночку длиной около 1 м с бортиками высотой и шириной 0,2 м. На открытом воздухе разводят костер, подвешивают или ставят на кирпичи наполненный водой бак и загруж ают небольшими пучками прутья в кипящую воду. Е сть и другой вариант отваривания прутьев. Во избежание несчастных случаев сначала прутья небольшими пучками укладывают в бак, заливают холодной водой и придавливают, чтобы они не всплывали, грузом или ивовыми палками, упирая концы их в стенку бака. П рутья кипятят в воде, постоянно контролируя момент, когда кора начнет легко отделяться от древесины, затем их сразу вынимают из воды, иначе при более длительной варке прутья станут грубыми, древесина их потемнеет. Время обработки прутьев зависит от разновидности ивы, а также от того, какого цвета прут хотят получить. Если необходим слегка тонированный оттенок, достаточно прокипятить прутья в течение 30 мин, а чтобы получить прутья густого, темного цвета — 2 ч и более. С ущ ествую т несколько способов ускорения проварки прутьев: прутья предварительно замачивают в холодной воде на 2— 3 ч; в воду при закипании добавляют питьевую или каустическую соду (1 0 0 г на 1— 1,5 ведра); после первой проварки прутьев, срезанных на определенном участке, можно точно определить время обработки этого материала, чтобы не допускать переваривания в дальнейшем. Обработка проваренных прутьев. Проваренные прутья помещают в холодную воду до полного охлаждения или раскладывают на свежем воздухе, чтобы древесина лучше очищалась от коры. П рутья можно оставить в растворе до полного охлаждения, а на другой день приступить к очистке, при этом цвет прутьев станет темным. Отбеливание. Больш инство мастеров в своей работе не пользуется какими-либо красителями, стараясь сохранить естественный цвет прута. А для осветления и получения равномерной окраски готовое изделие кистью промазывают 15— 20% -н ы м раствором перекиси водорода. Затем после просушки поверхность как обычно покрывают лаком. Сушка окоренных прутьев. В осенне-зимний период прутья сушат в закрытых отапливаемых помещениях, раскладывая у батарей или 12
поставив вдоль стен верхушками настилах (см . рис. 1).
вверх,
а также
на специальных
Хранение прутьев П рутья, заготовленные в весенне-летний период, до осени хранят связанными в пучки в проветриваемом сарае или под навесом. Х ранить их в условиях повышенной влажности нельзя — они покроются плесенью. П оэтом у, как только наступят ненастные дни, прутья переносят в сухое теплое помещение (в кладовую или даже в жилую комнату). В этих условиях материал отлично сохраняется в течение нескольких лет. Оставш иеся непроваренными и неокоренными прутья хранят зимой в неотапливаемом помещении, например в сарае, а в условиях городской квартиры — на балконе или лоджии, кроме того, без какого-либо ущерба для качества прутья можно хранить на открытом воздухе закопанными в снег. Во всех случаях пучки прутьев предварительно заворачивают в полиэтиленовую пленку. Так же хранят и проваренные прутья.
Заготовка лент Для плетения некоторых изделий применяют ленточный материал. Лентами выплетают целые полосы корзин, сухарниц, хлебниц, ваз, а также определенные ряды, отделывают ручки изделий и используют как закрепляющий материал. Ленты изготавливают на специальных станках или с помощ ью простого приспособления — колунка (ри с. 3 ). Диаметр прутьев для изготовления лент может быть любым в зависимости от того, для какой цели нужна лента. Сначала увлажненные ивовые прутья раскалывают на 3 или 4 части. Д ля этого комлевый конец прута расщепляют ножом, вставляют в расщеп колунок и ровно ведут вниз (ри с. 4 ). После чего остругивают, снимают сердцевину и внутренний слой древесины, чтобы осталась тонкая лента. Для работы нужны ножи — горизонтальный (ри с. 5 ) для снятия сердцевины и вертикальный для получения лент определенной ширины. Иногда прутья расщепляют на две части вручную, без применения колунков, получая половинные ленты (ри с.
6 ).
Организация рабочего места Х о р о ш о организованное рабочее место, обеспеченность нужными инструментами и приспособлениями, необходимым материалом оказы вают существенное влияние на качество плетеных изделий. 13
Р ис. 3. Колунки
В мастерских или учебных классах должны быть хорошее дневное и электрическое освещение, водопровод, лучше с горячей водой, ванна для замочки прутьев, кладовая для хранения материала, наборы инструментов, шаблоны и другие необходимые при работе приспособле ния. К аж дый ученик должен иметь свой стол и стул. Столы размещают с таким расчетом, чтобы при плетении работающие не мешали друг другу. Столы делают прочными и устойчивыми, длиной 60 см, высотой 65— 70 см, шириной 50 см. Столешницу выполняют из досок толщиной 4— 5 см. Стулья должны обеспечивать правильное положение тела во время работы. Для взрослых и подростков высота сиденья стула — 48— 50 см, высота спинки от сиденья — 35— 40 см. Рабочие места в мастерских или учебных классах должны быть оборудованы в соответствии с требованиями производственной санитарии, гигиены и техники безопасности. В домашних условиях стол и стул для работы делают таких же размеров и размещают в удобном месте. М ож но работать и за обычным столом, но чтобы не испортить его покрытие, на столешницу необходимо класть фанеру или доску.
Техника безопасности На рабочем месте — в учебном классе или дома надо бы ть предельно внимательным, чтобы при работе с ножом не нанести рану себе или товарищу. Малейшее неправильное движение, поспешность или легко мыслие могут привести к серьезной травме. Н едостаток освещения рабочего места также нередко становится причиной несчастных случаев и различных заболеваний глаз. В рабочем помещении необходимо соблю дать правила противопо жарной безопасности. После работы подметают мусор (обрезк и прутьев, к ор у) и выносят в специально отведенное место. П ользо ваться в помещении открытым огнем при подогреве воды для отма чивания материала запрещается.
Инструменты, шаблоны и приспособления для плетения Д ля изготовления изделей из ивового прута необходим опреде ленный набор инструментов, шаблонов и приспособлений. Часть этих инструментов следует сделать самим: ножи — цельный и складной, изготовленные из хорошей стали с тонким лезвием. И спользую т их для заготовки материала, заострения и обрезки свободны х концов прутиков в процессе плетения; щемилка (ри с. 7 ) служит для снятия коры с прутьев. Д елают ее из ивовой палки диаметром 25— 30 мм, длиной 550— 600 мм. Один конец 16
пропиливают ручной ножовкой на 220— 250 мм, чтобы получился расщеп шириной 2— 3 мм, палку ниже расщепа обматывают изоляци онной лентой или проволокой, конец палки заостряют, чтобы втыкать его в землю (ри с. 7, а). М ож но также просверлить в палочке отверстие диаметром 3— 3,5 мм на расстоянии 220— 250 мм от верхнего края, а затем ножовкой сделать пропил до этого отверстия (ри с. 7 ,6 ). Такая конструкция более прочная; шило с загнутым стержнем. Основное назначение — плетение донышка, вставка дополнительных стоячков, уплотнение стенок изделий и т .д . И зготовляется из гвоздя длиной 110 мм, диаметром 5 мм. Ручка деревянная, длиной 90 мм. У гвоздя нужного размера отпиливают шляпку и сплющ ивают отпиленный конец молотком, придав ему форму лопаточки. К онец гвоздя затупляют и забивают «лопаточку» в деревянную ручку, чтобы гвоздь не вращался в ней. Затем выгибают его до нужного угла (рис. 8 ). При плетении мелких изделий потребуется шило, имеющее загнутый стержень небольшого (2 ,5 — 3 мм) диаметра. Ш ило можно изготовить и из отвертки; груз (небольш ая металлическая болванка с ручкой) служит для удобства плетения донышка и стенок изделий. Д ля изготовления груза к круглой болванке высотой 70 мм, диаметром 80 мм приваривают ручку из проволоки диаметром 4— 5 мм, высотой 40— 50 мм (ри с. 9 ). При необходимости грузы можно делать разных размеров; колотушка служит для уплотнения стенок изделий, особенно больших корзин. Изготавливается из твердой древесины длиной 200— 220 мм, шириной 20 мм, толщиной 15 мм (ри с. 10). Остальные инструменты — бокорезы , плоскогубцы, круглогубцы, линейку, циркуль, обычное шило, секатор можно приобрести в магази не. Бокорезами обрезаю т свободные концы прутьев, плоскогубцами протягивают прутья при плетении, круглогубцами сжимают стоячки в местах сгиба и т. д. Шаблоны (болван ки) из дерева, фанеры, пенопласта, прута, проволоки применяют для придания нужной формы будущ ему изделию. К ачество плетения, удобство в работе во многом зависят от того, как сделаны шаблоны, которые должны строго соответствовать форме и размеру изделий. И зготовлению их уделяют особое внимание. Не все болванки делают вручную, некоторые из них вытачивают на токарном станке из дерева. Ниже рассказано об изготовлении шаблонов, предназначенных для плетения изделий, описанных в данной книге. Шаблон из фанеры с деревянной подставкой. В середине кружка из пятислойной фанеры толщиной 5 мм, диаметром 150— 300 мм делают отверстие для шурупа (ри с. 11, а). К руглую подставку диаметром 20— 80 мм выполняют из дерева, вы соту подставки определяют в зависимости от назначения: для конфетницы, корзинки и др. (ри с. 1 1 ,6 ). Например, для сухарницы нужна подставка 17
ч 9 7 Ю тг Р ис. 7. Щемилки: а — с разрезом; б — с отверстием
Рис. 8. Шило с загнутым концом
Р ис. 9. Груз Рис. 10. Колотушка
Рис. 11. Шаблон с подставкой: а — кружок ии фанеры; б — подставка
Рис. 12. Обруч-шаблон круглый Рис. 13. Обручшаблон овальный Р ис. 14. Болванкашаблон д л я хлеб н и ц ы Рис. 15. Болванка для корзинки под бутылку: 1 — отверстие для шурупа; 2 — разметка
Рис. 16. Болванка для четырехгран ной вазы: а — основная часть; б — верхний шаблон; в — нижняя часть
Рис. 17. Болванка большая из дерева: а — основная часть; б — малая болванка; в — плоская болванка
В
Рис. 18. Прямоу гольная деревянная оправа Р ис. 19. Шаблон для дамской сумочки: А — передняя стенка; Б — боковая стенка; В — донышко
Р ис. 20. Фанерный диск Р ис. 21. Подставка круглая Р ис. 22. Тренажер
высотой 60— 65 мм с фанерным кругом диаметром 200— 220 мм. Обруч-шаблон применяют при плетении корзин, хлебниц, сухарниц, ваз и др. Делают его из орехового или ивового прута. Размеры зависят от размера изделия, форма круглая (ри с. 12) или овальная (ри с. 13). Как делать обруч, описано ниже. Б о л в а н к а - ш а б л о н из дерева для хлебницы (ри с. 14). Д иа метр нижней ч а с т и — 140— 145 мм, верхней — 230— 250 мм, вы со та — 60— 65 мм. Внизу в центре делают отверстие для шурупа. Б о л в а н к а к р у г л а я из д е р е в а д л я к о р з и н к и п о д ш а м п а н с к о е . Для плетения поясков и рисунков определенного размера предварительно карандашом делают разметку на болванке (рис. 15). Нижняя часть диаметром 80— 85 мм, верхняя диаметром 100 мм, высота — 170 мм. Болванка из д е р е в а для ч е т ы р е х г р а н н о й вазы состоит из трех частей. Основная часть круглая с прямоугольным верхом (ри с. 16, а ), который обивают фанерными деталями с овальными закруглениями (ри с. 16, б ) . Высота основной ч а с т и — 270— 280 мм, снизу — диаметром 70— 80 мм, сверху — квадрат сечением 1 2 0 х 120 мм. Верхний фанерный шаблон длиной 120 мм, высотой 90 мм (ри с. 16, б ) . Высота нижней части — 90 мм, диаметр снизу — 160— 170 мм, сверху — 70— 80 мм (рис. 16, в ). Болванка большая круглая из дерева. Диаметр основной части снизу — 70— 80 мм, сверху — 120 мм, высота — 250 мм (ри с. 17, а). К ней крепят малую болванку диаметром внизу 140 мм, вверху — 70— 80 мм, высотой 60— 70 мм (ри с. 17, б ) или плоскую болванку диаметром снизу 140— 150 мм, сверху — 70— 80 мм, высотой 40— 50 мм (ри с. 17, в) . П р я м о у г о л ь н а я д е р е в я н н а я о п р а в а из досок толщиной 6— 10 мм (ри с. 18) используется при плетении корзинок для рукоделия, небольших вазочек и т. д. Размеры оправы определяют в соответствии с размерами изделия. Ш а б л о н д л я д а м с к о й с у м о ч к и . Передние стенки и доныш ко делают из тонкой трехслойной фанеры, доныш ко (2 7 0 — 2 8 0 X 9 0 0 ), боковые овальные стенки из доски толщиной 80— 85 мм, высотой 210 мм (рис. 19). Н аруж ную сторонку доски делают выпуклой. К р у ж к и (д и ск и ) из фанеры толщиной 5 мм и более необходимы для плетения различных изделий круглой и шарообразной формы (ри с. 2 0 ). Д ля работы надо иметь несколько таких кружков диаметром от 80 до 150 мм. В центре делают отверстие для шурупа, а на плоскости просверливают отверстия диаметром 1,5— 6 мм. Эти отверстия располагают по концентрическим окруж ностям, в торцевой части диска также сверлят отверстия. П о д с т а в к а к р у г л а я из трехслойной фанеры для плетения и выравнивания донышка (ри с. 2 1 ). Диаметр п одставки — 120,150, 180 мм и т. д. К олунки (см . рис. 3 ) делают из твердого дерева толщиной 30 мм, длиной 80 мм. Т олсты й конец колунка должен быть выпуклым, а тонкий иметь 3— 4 ровных выреза. 22
Тренаж ер. Для первичной отработки основных приемов плетения делают круг из плотной древесины диаметром 180— 200 мм, толщиной 30— 25 мм (ри с. 2 2 ). Отступив от кромки круга 10 мм, по периметру просверливают нечетное количество отверстий диаметром 5 мм на расстоянии 20 мм друг от друга. М еж ду этими отверстиями можно просверлить дополнительные меньшего ( 3 — 3,5 мм) диаметра. Мелкие отверстия на тренажере можно использовать для тренировки по выполнению отделки бортиков корзин, сухарниц, кашпо и т. д. Кроме того, отверстия делают по торцевой части круга. Д ля работы на тренажере заготавливают постоянные стоячки длиной 150— 200 мм. Стоячки должны крепко держаться в отверстиях.
Подготовка прутьев к плетению Приступая к плетению, подбирают необходимое количество прутьев нужного диаметра и длины в зависимости от изделия, которое будут делать. Д ля стоячков заготавливают пруты с малой сердцевиной, упругие и прямые. Длина их также зависит от высоты, размера и формы изделия. Д ля плетения стенок нужны прутья большей длины и с большей сердцевиной, для донышка — мелкий мягкий прутик (макушечный материал), а для веревочек и оплетки ручек подбирают длинные упругие прутья. Прутья для стоячков должны бы ть с наименьшим конусом, ровные, без повреждений, сучков и бородавок, одинаковой жесткости. Прутья с мелкими дефектами можно использовать при плетении стенок, донышка и т. д. Весь необходимый материал надо заготовить заранее. Д о начала плетения или тренировочного занятия прутьям надо придать гибкость и эластичность. Для этого необходимо замочить их в теплой воде на 1— 2 ч. П родолж ительность замачивания зависит от диаметра прутьев и от размера сердцевины: чем меньше сердцевина, тем дольше выдерживают их в воде. Окоренные прутья не следует передерживать в воде — они почернеют. П оэтом у рекомендуют вымачивать прутья в несколько приемов. Если прут после замачивания будет ломаться, его надо еще раз замочить, но на более короткий срок. Во время плетения прутья держат во влажной плотной ткани, чтобы сохранить их гибкость и эластичность. Высыхающие прутья в процессе плетения обы чно протирают влажной тряпочкой. П рут, заготовленный в осенне-зимний период, лучше замачивать в холодной воде. Э тот материал в воде выделяет дубильные и красиль ные вещества, поэтому рекомендуется пользоваться выделенной специально для этой цели посудой. После окончания работы оставшиеся прутья свободн о раскладывают 23
и суш ат. Для сохранения качества и экономии прутьев необходимо готовить только потребное количество.
Приемы работы ножом Прежде чем приступить к плетению изделий, необходимо научиться приемам пользования ножом при срезе прутьев и выбрать для себя наиболее удобный. Таких приемов два. Первый прием. П рут берут в левую руку и направляют комельком к себе, а правой рукой ножом на себя делают срез с небольшим уклоном длиной 10 мм (ри с. 23, а ). Второй прием. П рут берут в левую руку и направляют комельком от себя, а правой рукой ножом от себя делают срез, также с небольшим уклоном. Такие срезы следует делать с одного раза, поэтому нож должен бы ть очень острым. Д ля того чтобы вставить стоячки в донышко, их заостряют на 15— 20 мм, что зависит от размера изделия и соответственно от размера донышка. Э тот срез делают также с небольшим уклоном, только он должен бы ть значительно длиннее, так называемый у д л и н е н н ы й с р е з (ри с. 23, б ) . К огда плетут корзину с обруча, для закрепления стоячков на обруче делают с р е з на у с . Для чего отмеряют нужную длину стоячка у комелька, прорезают его до середины и срезают на ус (ри с. 23, в ). Длина среза (1 0 0 — 160 мм) зависит от толщины обруча и от того, как стоячок один или два раза он будет обвивать обруч. Ч тобы быстрее и легче сделать срезы нужной длины, пользуются палочкой-меркой, по которой размечают место среза на каждом пруте. Н еобходимо обращать внимание на осторож ность и аккуратность обращения с ножом. О б этом надо помнить не только в процессе учения, но и в дальнейшей работе.
Основные виды плетения Существует три основных вида плетения: прямое, простая веревочка в два прутика, веревочка в три прутика; обычно плетут слева направо. Прямое плетение — один из самых распространенных видов применяется при изготовлении стенок, донышек, крышек, практически всех изделий. Выполняют его очень бы стро, известно много вариантов прямого переплетения. Стоячков долж но быть нечетное количество. П ростая веревочка в два прутика обы чно выполняется при изготовлении оснований изделий, для закрепления стоячков на обруче, а также для отделения одного вида плетения от другого и т. д. Таким плетением выполняют целые полосы, ряды или только один ряд. Для 24
этого часто используют цветные прутья как неочищенные разной расцветки, так и проваренные. Веревочку в три прутика применяют для соединения полос, закрепления нижней и верхней частей изделия, например корзинки, что увеличивает его прочность. Э тот вид плетения выглядит наиболее эффектно, если использовать более толстые прутья по сравнению с теми, которые вплетают в стенку изделия. Ч тобы отделить один вид плетения от другого, можно использовать цветной материал как неочищенный, так и проваренный. Для сплошного плетения веревочка в три прутика применяется очень редко.
Прямое (простое) плетение (рис. 24) Сначала осваивают этот вид плетения на тренажере: в отверстия диаметром 5 мм вставляют длинные стоячки (ри с. 25, а). Ч тобы было удобнее, макушки стоячков связы вают (ри с. 25, б ) . Прутики (о ч и щенные или вымоченные) зачищают на срез с небольшим уклоном. Берут один прут, вставляют комельком между двумя любыми стоячками на тренажере (ри с. 26, а) и начинают оплетать стоячки, пропуская его поочередно то спереди, то сзади (ри с. 26, б ) до конца прутика. Затем его тонкий конец обрезаю т на скос и оставляют его с задней стороны стоячка. Присоединяя новый прут, его помещают за этим же стоячком слева ниже обрезанного прута (ри с. 26, в ) и продол жают плетение. Для того чтобы стенки изделия получались ровными, тонкий конец прута сращивают с толстым. Так плетут до нужной высоты. Концы обрезанных на срез прутьев каждый раз пропускают с задней стороны стоячка, т. е. оставляют внутри тренажера. П рутья можно использовать несколько раз, окоренные следует заново отмачивать. Прямое плетение можно вести одновременно двумя прутиками, выполняя сразу 2 ряда. При этом в изделии долж но бы ть четное число стоячков. Одним прутиком проплетают первые 3— 4 стоячка, затем левее первого вставляют второй прутик и плетут ими поочередно до конца. Варианты прямого плетения Простое плетение (ри с. 2 7 ) выполняют так: огибают прутом один стоячок сзади, два спе'реди. Таким способом чаще всего изготавли вают круглые настенные украшения. Плетение в шахматку (ри с. 28, а). О гибаю т два стоячка сзади, два спереди (ри с. 28, б ) . При этом используют прутья двух цветов, причем первый ряд выполняют белым прутом, второй ряд — цветным (ри с. 28, в ), чередуя их до нужной ширины полосы. После того, как будет выплетена первая полоса с квадратиками двух цветов, вторую полосу плетут так, чтобы над квадратиками одного цвета находились 25 I
Рис. 23. Срезы прутьев: с/ — малый; б — удлиненный: ч — срез на ус
Рис. 24. Прямое плетение
Рис. 25. Подготов ка тренажера к плетению: а — стоячки, вставленные в отверстия; б — связанные макушки стоячков
Р ис. 26. Выполне ние прямого плетения: а, б — порядок работы; в — соединение прутьев
с. 26. Продолжение
Рис. 2 1 . Выполне ние простого плетения
Рис. 28. Плетение в шахматку: а — общий вид; б — порядок работы; в — первый ряд (вид сверху)
Р ис. 28. Продолжение
Рис. 29. Спиральное плетение: а — общий вид; б — порядок работы; / — 8 — стоячки
квадратики другого цвета. Для этого вторую полосу начинают плести прутом такого же цвета, которым закончена первая полоса. Спиральное плетение (рис. 29, а). Сначала заплетают пять стоячков ( / — 5 ) прямым плетением (оплетая поочередно каждый стоячок то спереди, то сза д и ), затем три стоячка ( 6 — 8) обводят снаружи, далее пять стоячков поочередно и т. д. (ри с. 29, б ) . В работе долж но быть определенное количество стоячков: 15,23 (1 5 — j—8 ), 31 ( 2 3 + 8 ) , ...,п — I—8. Число их зависит от размера будущ его изделия. Если установлено 15 стоячков, при плетении получатся два витка, 23 стоячка — три витка, 31 стоячок — четыре витка. Такой вид плетения применяют в изделиях шаровидной и конусной формы. Послойное (косое) плетение (ри с. 30, а). К каждому стоячку на изделии подставляют прутики и поочередно заплетают их. Если на изделии 20 стоячков, надо заготовить столько же прутиков одинаковой длины, толщины и жесткости. Плести можно начинать с толстого конца и с вершинок. Этим способом выплетают целые полосы и даже несколько полос, а между ними выполняют веревочку в два или три прусика. Плетение идет справа налево. П рут / заводят за стоячок, направляя его под углом к Донышку, и оплетают поочередно стоячки: соседний спереди, следующий сзади и конец выводят наружу (ри с. 30, б ) . Плетение прутиком 2 начинают с левой стороны стоячка В, при этом также поочередно оплетают соседний стоячок спереди и следующий сза ди, а конец выводят наружу. П родолж аю т в такой последовательности заплетать остальные прутья, пока не замкнется круг. Все концы прутьев должны находиться с наружной стороны . Затем любым из концов оплетают сзади следующий стоячок и таким образом по порядку справа налево заплетают концы прутьев на всю длину. Все прутья должны обогнуть одинаковое количество стоячков. Так выплетают целый слой. В работе можно использовать по 2 прута разного цвета, пропуская их одновременно между одними и теми же стоячками.
Простая веревочка в два прутика (рис. 31, а) Д ля этого вида плетения готовят длинные и упругие прутья, толстые концы срезаю т с небольшим уклоном. Длина прутьев должна быть разной, тогда при сращивании их концы не совпадут в одном месте. На тренажере ставят стоячки в отверстия диаметром 5 мм. П рутья / и 2 закладывают комельком под стоячки А и Б (ри с. 31, б ) , затем прутиком / обводят снаружи стоячок £ , а В — с внутренней стороны и выводят прут наружу между стоячками В и Г (ри с. 31, в ). П рутиком 30
2 огибают снаружи стоячок В, а с внутренней стороны — Г и вы во дят наружу между стоячками Г и Д (ри с. 31, г ). В таком порядке про долж ают плести до тех пор, пока не замкнется круг. Веревочка в ажурном плетении. Вставляют два прутика под любые два стоячка. Прутиком 1 обводят снаружи снизу стоячок А и пру тик 2, затем с внутренней стороны обводят стоячок £ , выводят пру тик наружу и т. д. (ри с. 3 2 ). Прутиком 2 огибают снаружи стоячок Б и снизу прутик / , а стоячок В — с внутренней стороны , и выводят наружу. Плетение продолж ают до конца прутика, затем вплетают новый. Таким способом выплетают узкие полоски на стенках изделий. О собенно красиво это выглядит в следующем сочетании: делают одну простую веревочку в два прутика, а следую щ ую (св е р х у ) — веревочку в ажурном плетении. Получается своеобразная цепочка. Такой рисунок называется елочка (ри с. 3 3 ).
Веревочка в три прутика (рис. 34, а) На тренажере в отверстия диаметром 5 мм ставят упругие стоячки. П рутья / , 2, 3 закладыват за три соседних стоячка А , Б, В (ри с. 34, б ) . П рутиком / слева направо огибают снаружи стоячки Б и В, а стоячок Г — сзади и выводят между стоячками Г и Д (ри с. 34, в ). Прутиком 2 огибают снаружи стоячки Б и Г, а стоячок Д — сзади и выводят вперед между стоячками Д и Е (ри с. 34, г ). Прутиком 3 огибают снаружи стоячки Г и Д, а сзади Е и выводят вперед между стоячками Е и Ж (ри с. 34, д ). Затем повторяют эти приемы, переплетая вправо каждый левый прут и огибая им снаружи два стоячка, а с внутренней стороны один, выводят прут наружу, и т. д. П родолж аю т плетение до тех пор, пока не вернутся к стоячку, с которого начали работу. Если требуется еще одна веревочка в три прутика, необходимо сделать плавный переход, чтобы в этом месте не образовалась «ступенька». Такой переход каждый раз делают в одном и том же месте, только вместо левого прутика / берут правый 3 и огибают им два стоячка снаружи, а третий сзади и выводят его вперед (ри с. 34, е). Так же выполняют переход средним ( 2 ) и левым ( / ) прутиками. При плетении стараются указательным и большим пальцами левой руки придерживать стоячки в нужном направлении.
Кромки Д ля завершения изготовления лю бого изделия необходимо освоить плетение кромок (коси чек) и бордю ров, которые служат отделкой бортика корзины, кашпо, сухарницы, хлебницы, вазы и т. д. Их выплетают из свободны х концов стоячков, а также подставляя 31
Р ис. 31. Продолжение
Г
дополнительные стоячки из цветного и белого прутьев. Количество материала, необходимого для плетения кромки, зависит от способа ее выполнения, а также от длины стоячков и расстояния между ними. Отработка кромок на тренажере. П рутья длиной 200— 300 мм вставляют в малые (диаметром 3 мм) отверстия на тренажере. Для тренировки можно использовать оставшиеся после плетения макушки прутьев, а также специально заготовленный материал. П рутья отмачивают довольно долго, чтобы они стали мягкими и эластичными. Первая кромка с загибом за один стоячок (ри с. 35, а). П редвари тельно заготавливают несколько палочек, толщина которы х должна бы ть равна толщине стоячков, а длина — 80— 100 мм. Закладывают палочку под стоячок А , загибают его вниз через палочку, обогнув спереди соседний стоячок £ , конец выводят внутрь тренажера и обрезаю т (ри с. 35, б ) . Так же последовательно загибают все стоячки (ри с. 35, в ). Последний из них займет место палочки. Затем шилом уплотняют плетение, чтобы прутья лежали ровно, и укорачивают их на срез. Вторая кромка (ри с. 36, а). Закладывают палочку под любой стоячок тренажера, загибают первый стоячок через палочку, пропуска ют сзади соседнего стоячка и спереди следующего, затем заводят его конец внутрь и отрезаю т на срез (ри с. 36, б ) . Так же загибают все остальные стоячки. Последний стоячок пропускают под уже загнутый на место палочки, огибают им спереди следующий стоячок и выводят внутрь тренажера. Третья кромка (ри с. 37, а). Закладывают палочку под любой стоячок, загибают его через палочку, пропускают сзади соседнего стоячка, обводят спереди два следующих, еще один сзади и обрезаю т на срез (ри с. 37, б ) . Так продолж ают делать кромку, последовательно загибая все стоячки. Последний стоячок пропускают под уже загнутый на место палочки, огибают два спереди, один сзади и обрезаю т конец. Четвертая кромка (ри с. 38, а). Закладывают палочку под любой стоячок, загибают его через палочку, огибают два стоячка спереди и заводят за третий (рис. 38, б ) . Так делают кромку, последовательно загибая все стоячки, затем укорачивают концы на срез. Кромка в три пары прутьев. Э тот вид кромки называют также «розга». На тренажере в малые отверстия вставляют стоячки длиной 250 мм. П од любые три стоячка закладывают палочки, толщиной, равной толщине стоячков. Загибаю т стоячок / (ри с. 39, а) сзади стоячка 2 и выводят наружу, стоячок 2 — сзади стоячка 3 и выводят наружу, стоячок 3 — сзади стоячка 4 и также выводят наружу. Концом стоячка / огибают спереди стоячки 3 и 4 и сзади стоячок 5, стоячок 4 загибают и кладут вдоль стоячка / (ри с. 39, б ) . Получается первая пара прутиков. Так же загибают стоячки 2 и 3, чтобы получилось три пары прутиков: / и 4 Щ2 и 5, 3 и 6, концы которых выведены наружу (ри с. 39, в ). Далее берут из левой пары прутик 4 , загибают его справа за стоячки 6 и 7 снаружи и за стоячок 8 сзади, конец выводят наружу, а стоячок 36
7 кладут сзади вдоль конца стоячка 4. О сталось снова три пары прутьев: 2 и 5, 3 и 6, 7 и 4, а прутик / — одиночный. Затем все повторяют: берут из левой пары правый конец; если он сломался, можно брать из пары левый, обводят справа за два стоячка снаружи, один сзади и выводят конец наружу, а очередной прямой стоячок кладут сзади вдоль конца стоячка и т. д. Последний стоячок загибают и пропускают под сгиб первого на место палочки. Берут из левой пары конец и пропускают под сгиб первого стоячка, следующий левый конец проводят сверху парных прутьев и пропускают под сгиб стоячка 2 вместо палочки. Снова из левой пары проводят конец прутиков и пропускают под сгиб стоячка 3 вместо палочки, второй конец из этой пары прутьев проводят сверху под сгиб стоячка 4 (рис. 39, г ). Оставшиеся единичные прутики пооче редно подтягивают и обрезаю т. Концы этих прутиков должны вы хо дить вперед снизу кромки. Д ля выравнивания кромки переворачивают тренажер и кладут его на гладкую поверхность, сверху ставят груз и оставляют до полного высыхания. К ромка в четыре пары прутьев. Э тот способ применяют также при завершении плетения изделий и выполняют из свободны х и дополни тельных стоячков. При плетении в три пары прутиков получается узкая кромка, а из четырех и более — широкая, которая служит для украшения больших корзин и других изделий. Если стоячки в изделии находятся на большом расстоянии друг от друга, кромку надо заплетать в три пары прутьев, и наоборот, если стоячки расположены часто, плетут кромку в четыре и более пары прутьев. П од первые четыре стоячка закладыват 4 палочки, диаметр которых должен быть равен диаметру стоячков. Загибаю т стоячок / вправо сзади стоячков 2 и 3 и выводят его наружу, стоячок 2 — сзади стоячков 3 и 4 и выводят, стоячок 3 — сзади стоячков 4 и 5 и выводят, стоячок 4 — сзади стоячков 5 и 6 и выводят (ри с. 40, а). П олучилось 4 загнутых стоячка, концы которы х выходят наружу. Затем берут конец / и огибают им снаружи стоячки 4, 5, 6 и сзади — 7, а стоячок 5 загибают и кладут вдоль стоячка / . Получилась правая пара прутиков ( / и 5 ), выведенных наружу (ри с. 40, б ) . Так же загибают стоячки 2, 3, 4 , чтобы всего получилось четыре пары прутьев: / и 5, 2 и 6, 3 и 7, 4 и 8, концы которы х выходят наружу (ри с. 40, в ). Затем все повторяют: берут из левой пары прутиков правый конец 5, обводят снаружи три последующ их стоячка и один стоячок сзади, выводят конец наружу, а стоячок 9 загибают и кладут вдоль стоячка 5. Так продолж ают заплетать до тех пор, пока не останутся выходящие наружу одиночные прутья. По окончании работы подтягивают концы стоячков для уплотнения плетения, а оставшиеся кончик” у р е з а ю т наискосок около каждого стоячка и выравнивают кромку.
Рис. 36. Вторая кромка: а — общий вид; б — порядок работы
Р ис. 37. Третья кромка:
« ■
а — общий вид; б — порядок работы
Ажурное плетение А ж урн ы м называется плетение с просветами или открытыми ячейками. Виды этого плетения разнообразны : прямое, крестиком, ром&иком (ри с. 4 1 ). А ж урн ое плетение использую т в работе над особо нарядными изделиями — вазами, кашпо, сувенирами и т. п. Выполняют его в форме полосы, включенной в какой-либо вид простого плетения, при этом обязательно долж но бы ть четкое количество стоячков. П одробнее о выполнении простых и сложных ажурных полос рассказано в описании работы над конкретным изделием.
Бордюры При завершении плетения различных изделий — ваз, конфетниц, кашпо, фруктовниц, корзин небольших размеров, абажуров выполняют ажурное плетение в виде бордю ра из макушек и дополнительных стоячков. Б ордю ры бывают овальные и углом, простые и сложные, (ри с. 42, а, б, в ). Д елают их двумя, тремя и четырьмя прутиками, используя для этого дополнительный цветной и белый (очищ анны й) материал. При этом загиб может бы ть не только через один стоячок, но и через несколько, а верх — ровным или волнистым (ри с. 42, г, д ). Выполнение бордю ра как украшения плетения требует особы х навыков и мастерства. Какой бордю р делать на том или ином изделии, должен решить сам плетельщик. При этом следует учитывать длину макушек, расстояние между ними, диаметр окруж ности изделия, потребность в дополнительных стоячках и т. д. К огда делают загиб, прутья стоячков нельзя перемачивать — иначе коцы потеряют упругость и гибкость. Приступая к овальной загибке, необходимо промять стоячки большим пальцем, придав им дугообразную форму. Перед загибкой углом на прутиках отмеряют место, где будет находиться угол, и проминают его круглогубцами или надрезают ножом с внутренней стороны , чтобы прут не сломался (ри с. 4 3 ). П осле чего бокорезом укорачивают стоячок до нужного размера с припуском 30— 40 мм и заостряю т его. Бордюр углом и овальный бордюр. Различие технологии выполне ния этих бордю ров состоит только в том, что стоячок загибают углом или дугой. С тоячком 7 огибают снаружи стоячок 2 и вставляют его, проделав отверстие шилом, с левой стороны возле стоячка 3 (см . рис. 42, а). Так продолж ают плести до конца. Д ля того чтобы получился ровный верх, нужно постоянно измерять вы соту бордюра. Такой бордю р можно выплетать разными способами. При этом техника плетения остается та же, меняется лишь число огибаемых стоячков. Например, для плетения бордюра вторым способом стоячком 43
Р ис. 41. Виды ажура: а — прямой; б — крестиком; а — ромбиком
У
Р ис. 42. Виды простого бордюра: а — углом (1-й способ); б — овальный (1-й способ); в — углом (2-й способ); г — овальный (2-й способ); д — волнистый; 1— 9 — стоячки
г
ш
бордюр в два прутика: а — общий вид; б — порядок работы
Р и с . 45. Сложный бордюр в один прутик: а, б — первый способ; в — второй способ; /— 9 — стоячки
/ (см . рис. 42, в, г) огибают стоячки 2 и 3 снаружи (или изнутри) и вставляют слева от стоячка 4. Так же загибают стоячок 2 за стоячки 3 и 4 и снаружи (или изнутри) вставляют его слева от стоячка 5. Таким образом последовательно загибают все стоячки. Причем рисунок бордю ра не изменится от того, как огибать стоячки — снаружи или изнутри, такую загибку делают кому как удобнее. Такие бордю ры выполняют и в два прутика (р и с. 44, а, б ) . Сложный бордюр. Для придания прочности и отделки стенок хлебниц, фруктовниц, больших настенных украшений применяют более трудоемкие способы плетения. О собен н о сложна технология плетения бордю ра из четырех и более прутиков, поэтому загибку овалом делают одновременно несколькими прутиками — так они реже ломаются. Начинать осваивать этот вид плетения лучше с бордю ра в один прутик, постепенно усложняя работу. Сложный бордюр в один прутик можно выполнять двумя способами. Первый способ. Берут любой стоячок ( / ) и огибают им стоячки 2 и 3 спереди, 4 — сзади и заостренным концом вставляют его слева от стоячка 5 (ри с. 45, а). Так поочередно загибают все стоячки (ри с. 45, б ) . Второй способ. Стоячком / огибают стоячок 2 спереди, 3 — сзади, 4 — спереди, 5 — сзади и заостренным концом вставляют его слева от стоячка 6 (ри с. 45, в ). Таким образом загибают все стоячки.
Основы изделий К огда все основные виды плетения, кромки и бордю ры будут освоены на тренажере, можно приступать к изготовлению изделий. Ч тобы сплести какое-либо изделие, нужно иметь основу, на которую крепят стоячки. Для этого использую т обруч из ивового или орехового прута, круглое, овальное или прямоугольное плетеное донышко, диски из фанеры с просверленными в них отверстиями и всевозмож ные болванки. Обруч из ивового прута. Ф ор м у обруча определяют, исходя из формы будущ его изделия, круглую или овальную. Размеры основы также зависят от размеров изделия. Для того чтобы сделать обруч длиной 300 мм, шириной 200 мм, берут ореховый или ивовый прут длиной 1000 мм, толщиной у комелька 10— 12 мм. П рут проминают большими пальцами от толстого конца к макушке (ри с. 46, а). После чего выгибают на колене, придавая ему форму обруча. Затем заостряю т концы на ус на 150 мм каждый (тол сты й конец — с внутренней, тонкий — с наружной стор он ы ). П рут сгибают кольцом и туго связы ваю т капроновой ниткой или тонкой бечевкой (ри с. 46, б ) . Н итку вставляют под толстый конец прута и большим пальцем левой руки прижимают ее к срезу тонкого, правой рукой наматывают нитку по всей длине стыка и заводят между тонким и толстым концами. Затем обручу придают круглую или овальную форму. 49
Если нужна овальная основа, то берут тол стую бечевку и один конец привязывают на стыке концов прута, а другим стягивают противопо лож ную сторону обруча до тех пор, пока не получится необходимая форма. При этом стык должен оказаться на длинной стороне овального обруча (ри с. 4 7 ). Затем основу сушат. После сушки соединенные концы можно закрепить клеем типа «М ом ен т» или мелкими гвоздиками. На обруче намечают карандашом место будущ ей ручки. Основа для ручки. На корзине может бы ть одна поперечная или продольная ручка или две, расположенные с противополож ных сторон. Толщ ина основы для ручки зависит от величины корзины. Например, для заготовки ручки из ивового прута длиной 600 мм, толщиной 10— 12 мм выгибают дуж ку, ширина которой между концами должна соответствовать ширине корзины — 200 мм. В таком положении ее связы вают бечевкой и сушат (ри с. 4 8 ). После чего заостряю т концы с внутренней стороны на 70— 80 мм. Плетение донышка. Наиболее важный этап в работе — плетение донышка. О т того, насколько тщательно оно сделано, зависят прочность, форма и внешний вид изделия. Самые распространенные формы донышка — круглая и овальная. К орзины , хлебницы, сухарницы, всевозмож ные вазы под фрукты и цветы, напольные вазы, настенные украшения, а также подставки для посуды начинают выполнять с донышка. Плетут его очень плотно. Для плетения донышка любой формы делают крестовину из прочных с тонкой сердцевиной отрезков комлевой части очищенного прута. Палочки с рыхлой сердцевиной непригодны для этой цели. В зависимости от вида изделия крестовину делают из 4, 6, 8 или 10 палочек. К р у г л о е д о н ы ш к о . Для плетения круглого донышка диамет ром 150 мм берут 6 палочек длиной 180— 200 мм, диаметром 5 мм. К оличество палочек, из которых сложена крестовина, обозначают З Х 3. Сначала измеряют ширину трех сложенных палочек и по этому размеру вы резают пазы (д о сердцевины ) на трех других палочках, концы их с одной стороны заостряю т (ри с. 49, б ) , а затем весь мате риал замачивают в воде. Т ри первые палочки расщепляют в середине ножом или шилом (р и с.49, а) и вставляют в расщеп три палочки с пазами. Затем крестовину стягивают тонкой бечевкой или мягкой проволокой, чтобы после разведения концов не нарушилась плот ность ее центра (ри с. 49, в ). В любой крестовине получится четное количество концов, например^ 2х 2 (8 ш т.), З Х 3 ( 12), 4х 4 ( 16 ш т.). Если же для работы потребуется нечетное количество концов, в крестовину дополнительно можно вставить 1, 3 или 5 палочек такого же диаметра, но в два раза меньшей длины. Готовую крестовину ставят на круглую фанерную подставку, чтобы наружная сторона будущ его донышка оказалась внизу, т. к. при плетении концы прутьев будут выведены вверх. Затем оплетают крестовину от центра, начиная работу с тонких 50
концов прутиков и постепенно вводя прутья больш его диаметра. При этом концы крестовины разводят в стороны и заплетают 2— 3 ряда веревочкой в два прутика (ри с. 49, г ). Затем, чтобы на крестовине 3 X 3 образовались 13 концов, расщепляя палочку, шилом делают отверстие в углу крестовины и вставляют дополнительную (рис. 49, д ). П осле чего приступают к простому плетению, чтобы получить доныш ко нужного размера. На этой стадии работы очень важно выдержать равное расстояние между палочками. Возле двух соседних палочек на крестовине заостренными концами вставляют два длинных тонких прутика (ри с. 50, а) и завершают плетение донышка веревочкой в два прутика. Оставш иеся концы крестовины обрезаю т заподлицо с последним рядом. При изготовлении донышка больш ого диаметра можно вставить на одной окруж ности с противополож ных сторон по две дополнительные палочки рядом с каждой основной (ри с. 50, б ) , а затем продолжить плетение. Такое доныш ко обеспечит особую прочность. О в а л ь н о е д о н ы ш к о . Ч тобы сделать доныш ко длиной 275 мм и шириной 90— 95 мм, для крестовины берут 4 палочки длиной 320 мм, диаметром 5— 6 мм и 8 коротких палочек длиной 200 мм, диаметром 4— 5 мм. На длинных палочках делают заструг на половину их тол щины длиной 185 мм (ри с. 51, а ), короткие палочки расщепляют в середине и вставляют в них длинные, совмещая расщеп с застругом (р и с. 51, б ) . Расстояние между концами соседних коротких палочек долж но бы ть 23— 25 мм, две крайние с каждой стороны устанавливают вплотную друг к другу. Длинные палочки у конца заструга связы ваю т тонкой ниткой или проволокой. На рисунке 51, б показан образец с тремя длинными палочками, а для работы обы чно берут четыре. Д ля плетения потребую тся мелкие мягкие прутики для донышка, обычные прутья для веревочек и три дополнительные палочки. Готовую крестовину кладут вниз застругами. Начинают плетение с тонкой стороны прута. Сначала закрепляют короткие палочки с обеих сторон веревочкой в два прутика, затем простым плетением по периметру разводят концы длинных палочек. После двух-трех рядов плетения ставят 3 дополнительные палочки в углах крестовины (ри с. 51, в ), закрепляют их веревочкой в два прутика, переходя на прямое плетение, и плетут доныш ко до нужного размера. Все концы прутиков вы водят наверх для обрезки. Во время работы следят за ровностью плетения и расстоянием между палочками. С длинных сторон донышка подплетают дополни тельно по прутику для сохранения овальной формы. Заверш ают работу веревочкой в два прутика. К онцы палочек аккуратно подрезают бокорезами и кладут доныш ко под груз до высыхания. Фанерный диск. Д ля плетения некоторых изделий (каш по, ваз и т. д .) шаровидной, цилиндрической и другой округлой формы в качестве донышка использую т фанерные диски, которы е в отдельных случаях остаю тся внутри изделия. Д иск делают из фанеры толщиной 5— 10 1мм, по периметру просверливают отверстия диаметром 3— 6 мм, 51
Рис. 46. Обруч из ивового прута: а — заготовка обруча; 6 — закрепление концов
Рис. 50. Готовое донышко: а — общий вид; б — установка дополни тельных стоячков
Рис. 52. Плетение с фанерного диска: а — фанерный диск с отверстиями для стоячков; б — шаблон; в — крепление стоячков; г — оплетка стоячков
в которые затем вставляют стоячки (ри с. 52, а). Для придания изделию правильной формы на диск ставят шаблон (ри с. 52, б ) и оплетают его (ри с. 52, в, г ). Для плетения вазы с шаровидным основанием отверстия в фанерном диске просверливают с торцевой стороны. К диску ш урупом крепят оправу в форме полусферы (ри с. 53, а ), сверху присоединяют конусную болванку (рис. 53, б ), вставляют стоячки в отверстия, прогибают их по форме шаблона и поднимают вверх (ри с. 53, в ). Затем плетут изделие, а шаблон оставляют внутри. И спользуя в работе фанерный диск, можно сделать красивую рамку для фотографии или картины. В отверстия, просверленные с торцевой стороны фанеры, вставляют стоячки и закрепляют их двумя-тремя рядами веревочки в два прутика и завершают плетение бордю ром . На основании овальной формы таким образом можно сделать раму для зеркала (см . рис. 7 5 ). При. плетении изделий цилиндрической формы на болванку накладывают стоячки и стягивают их с торцевых сторон шпагатом, проволокой, резинкой (ри с. 54, а). Такой метод применяют, например, при плетении ножки для вазы. При этом ножку оплетают простым плетением или плотно укладывают стоячки вдоль деревянного конуса (ри с. 54, б ) , который оставляют заплетенным в ножке. Каркас. При плетении некоторых изделий как чисто бы тового, так и декоративного назначения предварительно связы вают каркас из прутьев (см . рис. 61, б ) . По простом у каркасу плетут корзинку с обруча, бел орусскую корзинку и т. д. Более сложные каркасы связывают для таких изделий, как «Г усены ш », вазы «Л ебедь», «У тка».
Плетение изделий П риступая к плетению того или иного изделия, надо прежде всего решить, каково его назначение, какой формы оно будет, кроме того, следует подготовить необходимые материал, приспособления и инстру менты. О собое внимание при этом уделяют качеству материала: его тщательно обрабатывают, подбираю т по размеру и цвету. Наиболее распространенные плетеные изделия — корзины хозяйственно-бы тового назначения. И х плетут из зеленого или белого (очи щ ен н ого) прута и прутьевых лент. О бучаясь плетению изделий, начинать лучше с изготовления корзины.
Плетение корзины с обруча (рис. 55, а) Размеры корзины: длина — 300 мм, ширина — 200, высота — 140— 150 мм. Для плетения п отребую тся: два ивовых или ореховых прута для 58
обручей длиной 1000 мм, толщиной 10— 12 мм; прут для ручки длиной 60 мм, толщиной 10— 12 мм; две направляющих палочки для ручки длиной 80— 100 мм, толщиной 10— 12 мм; 25 стоячков для каркаса корзины длиной 550— 600 мм, толщиной 4,5— 5,0 мм; прутья обычные для стенок, длинные и тонкие для веревочек и оплетки основы ручки; бечевка или проволока для закрепления обручей; клей, нож, шило и бокорезы . Подготовка материала. Сначала делают прут-основу для ручки, как описано выше, и два овальных обруча: первый длиной 300 мм, шириной 200 мм, второй (ш абл он) длиной 270— 280 мм, шириной 170— 180 мм. Д ве направляющих палочки застругивают на всю длину, 25 стоячков заостряю т на ус, длина заструга — около 100 мм. Точнее определить этот размер можно, сделав пробный загиб на обруче. Расстояние между стоячками — в среднем 30— 40 мм, оно зависит от размера корзины и толщины обруча. Весь заготовленный материал перед плетением замачивают в воде. Каркас. О бр уч ставят на колени ребром, правой рукой кладут стоячок на обруч срезом к себе, большим пальцем левой руки огибают срез вокруг обруча с левой стороны стоячка и вы водят вправо через стоячок с наружной стороны вдоль обруча (рис. 55, б ) , прижимая левой рукой срез к обручу. Затем берут следующий стоячок, кладут на обруч, не отпуская при этом конец первого стоячка. Большим пальцем левой руки нажимают на срез, огибают обруч с левой стороны стоячка и проводят вправо через стоячок вдоль обруча. Таким образом крепят все стоячки, а последний после охвата обруча заводят под обвивку первого. Такое плетение напоминает плетение венка из цветов. Стоячки крепят к обручу плотно и во время работы строго соблю даю т равное расстояние между ними. Затем обруч с закрепленными на нем стоячками ставят на стол, к нескольким стоячкам на высоте 250— 300 мм тонкой бе чевкой привязывают обруч-ш аблон меньшего размера и выплетают стенки корзины. Плетение стенок. Стоячки на обруче у основания оплетают однимдвумя рядами веревочки в два-три прутика, ставят направляющие палочки для будущ ей поперечной ручки на удлиненной стороне обручакаркаса. Затем работу ведут простым плетением на вы соту 140 мм и закрепляют веревочкой .в три прутика. После чего тщательно обрезаю т ножом оставшиеся концы прутиков внутри корзины. Во время плетения стенок следят, чтобы стоячки не заваливались в сторону, придерживая их большим и указательным пальцами левой руки. Если обруч-ш аблон мешает, его поднимают выше или снимают совсем, периодически проверяют стенки линейкой и выравнивают шилом или колотушкой. Плетение донышка. Д оны ш ко плетут из макушек стоячков. Сначала сжимают их круглогубцами у самого края корзины, а затем загибают навстречу друг другу, располагая поочередно то левый, то правый прут. Если работу ведут с очищенным прутом, концы макушек предваритель но отмачивают. П опарно уложенные стоячки обрезаю т с припуском 40— 70 мм, 59
Рис. 55. Плетение корзины с обруча: а — общий вид корзины; 6 — крепление стоячков к обручу; в — плетение донышка; г — оплетка ручки (концы выведены наружу); 4 — оплетка ручки (концы выведены внутрь); е — готовая оплетка
Рис. 55. Продол жение
каждый конец застругивают, загибают и вставляют в плетение (в зазор между прутьями) рядом со стоячками (ри с. 55, в ). Образовавш ийся каркас донышка заплетают простым плетением, начиная от кромки борта к середине, для чего использую т прутья гибкие, недлинные (например, обрезанные верхушки, оставшиеся от плетения других изделий), сюда же вплетают свободны е концы стоячков, не использованных в каркасе донышка. Плетение ручки. Вынимают направляющие палочки и вместо них вставляют на всю длину заструга прут-основу ручки. Высота ручки от донышка должна бы ть 280 мм. Затем берут 10— 12 прутьев, длина которы х на 300— 350 мм больше основы ручки, заостряю т их комлевые концы и вставляют по 5— 6 штук с каждой стороны корзины, слева от прута-основы . П рут-основу обвивают восьмеркой тремя-четырьмя витками (количество витков зависит от толщины руч к и ). Прутья выводят наружу между стоячками справа от основы (ри с. 55, г). Влажной тряпкой протирают тонкие концы, каждым из них охватывают ручку и вы водят их внутрь корзины (ри с. 55, д ). Затем концы прутьев заправляют под обмотку, увлажняют и заделывают между стоячками в стенку (ри с. 55, е). Так же оформляют ручку с противополож ной стороны . П рутья должны заполнить все просветы у основания ручки. Если на ручке останутся промежутки, не заполненные плетением, добавляют один или несколько прутьев с каждой стороны . Заплетка и крепление ручки в бортик должны бы ть плотными, с хорошей натяжкой. После просушки ручку у снования промазывают прозрачным клеем.
Плетение корзины с донышка (рис. 56) Размеры корзинки: в ы с о т а — 150 мм, диаметр дон ы ш к а — 150, диаметр верха — 220, высота ручки от дынышка — 260 мм. Для плетения потребуются: восемь палочек длиной 170— 180 мм, диаметром 5 мм для крестовины; три дополнительные палочки для донышка 4X 4+3; мелкий прут для плетения донышка; 25 стояч ков длиной 450— 500 мм, диаметром 4— 5 мм для каркаса; 23 прутика длиной 200— 250 мм, диаметром 2 мм для кромки донышка; прут для обруча-ш аблона диаметром 250 мм, длиной 800 мм, толщиной 8— 10 мм; прут для ручки длиной 600 мм, диаметром 8— 10 мм; две направляющие палочки для ручки; тонкие прутья для веревочек, оплетки ручки и стенок; нож, шило с загнутым стержнем, бокорезы , груз, бечевка, клей, лак. Подготовка к плетению. Для плетения корзинки необходимо сделать доныш ко диаметром 150 мм (см . рис. 49, 5 0 ), обруч-ш аблон диаметром 25 мм (см . рис. 4 6 ) и основу для ручки (см . рис. 4 8 ); две направляющие палочки застругивают на ус на всю длину. Плетение каркаса. Д оны ш ко кладут на стол лицевой стороной вверх. Стоячки заостренными концами вставляют в доныш ко рядом с палочка63
Рис. 57. Комбини рованная корзинка
ми, для чего предварительно шилом проделывают отверстия. Каждый стоячок при этом проминают круглогубцами или шилом у самой кромки донышка. Для плетения стенок корзины потребую тся 23 стоячка, поэтому к четырем палочкам донышка, расстояние между которыми наиболь шее, подставляют с двух сторон по стоячку (см . рис. 50, б ) . Затем на донышко кладут фанерную подставку диаметром 140 мм, ставят на нее груз. После чего, не снимая груз, поднимают все стояч ки вверх и туго связы вают макушки бечевкой. Если при формировании каркаса и плетении стенок донышко начинает коробиться, значит его плохо просушили, недостаточно промочили стоячки или, связывая макушки, забыли поставить груз. Плетение стенок. Стоячки оплетают веревочкой в три прутика. На высоте 300— 350 мм к четырем диаметрально противоположным стоячкам привязывают обруч-ш аблон. Развязы вают макушки и вырав нивают стоячки. Стенки заплетают простым плетением на вы соту 70— 80 мм. Затем на месте будущ ей ручки ставят направляющие палочки заостренной стороной внутрь. Стенки выполняют простым плетением на вы соту 130 мм, постоянно уплотняя ряды шилом или колотушкой. Заканчивают плетение стенок корзины 1— 2 рядами веревочки в два или три прутика. Плетение кромки в три пары прутиков. Длина концов стоячков должна бы ть не менее 200 мм. Более длинные концы обрезаю т. Затем их отмачивают. Для чего корзинку переворачивают вверх дном и ставят на 30— 40 мм в ведро так, чтобы вода не попадала на плетение. Убедивш ись, что стоячки стали гибкими и мягкими, приступают к загибке кромки в три пары прутиков (см . рис. 3 9 ). После чего корзинку ставят на стол, проверяют ровность кромки и, пока прутья не высохли, обрезаю т их концы внутри изделия. Кромка на донышке корзинки. Ш илом с загнутым стержнем проделывают отверстия рядом с основными стоячками и вставляют в них 23 стоячка меньшего размера, которые закрепляют, выплетая один ряд веревочкой в два прутика. При заплетении стоячки оттяги вают на себя, устанавливая их в вертикальное положение, и делают третью кромку (см . рис. 3 7 ). Затем проверяют ровность кромки. На корзину кладут больш ую фанеру, ставят на нее груз и оставляют до полного высыхания. Ручку делают в такой же последовательности, как для корзины с обруча (см . рис. 55 г, д, е).
Корзинка круглая комбинированная (рис. 57) Размеры корзинки: высота — 200 мм, диаметр донышка — 200, диаметр сверху — 300 мм. Для плетения потребуются: 8 палочек для крестовины 4 X 4 длиной 65
300 мм, диаметром 5— 5,5 мм; 3 дополнительные палочки; мелкие очищенные и цветные прутья для плетения основания комбинированно го донышка; 23 стоячка длиной 500— 550 мм, диаметром 4,5 мм для каркаса; 23 стоячка малого размера длиной 300 мм, диаметром 2— 2,5 мм для нижней кромки; средней толщины очищенные и цветные прутья для плетения стенок корзины; тонкие и длинные очищенные цветные прутья для плетения веревочек и оплетки ручек; прут длиной 800 мм, диаметром 7— 8 мм для ручки; 2 направляющие палочки для ручки; фанера-шаблон диаметром 240 мм с круглой подставкой диаметром 60 мм, высотой 90— 100 мм (м ож н о пользоваться и обручемшаблоном диаметром 300 мм ). Плетение донышка. К рестовину 4 Х 4 оплетают двумя веревочками, в два прутика, ставят 3 дополнительные палочки, делают две-три веревочки в два прутика. П родолж аю т плести очищенным прутом простым плетением до тех пор, пока диаметр донышка не будет равен 100 мм. Затем переходят к плетению цветным прутом до нужного размера (2 0 0 м м ). Заканчивают плетение донышка очищенным прутом веревочкой в два прутика. Уплотняя плетение, следят за ровностью стоячков и расстоянием между ними. Толщ ину прутиков от центра донышка постепенно увеличивают. О бр езаю т концы палочек и прутьев и кладут доныш ко под груз до высыхания. Плетение стенок. Д ля придания корзине правильной формы и удобства при работе доныш ко закрепляют на подставке — фанерешаблоне. Ш илом прокалывают пазы возле палочек и вставляют в доныш ко 23 стоячка (к четырем палочкам ставят дополнительно по одному стоя ч к у). На фанеру-шаблон ставят груз, проминают стоячки круглогубцами у самого основания корзины, поднимают их вверх и крепко связывают. Очищенными прутьями оплетают стоячки у основания двумя рядами веревочки в три прутика (переход ко второму ряду должен быть плавным). Плетение стенок выполняют простым плетением цветными прутика ми на вы соту 60 мм (9 — 10 р я д ов). Затем делают 3 ряда веревочкой в три прутика (средняя веревочка цветная). Снимают фанеру-шаблон с подставкой, кладут фанерный круж ок на доныш ко и ставят груз. Для дальнейшего плетения можно использовать обруч-ш аблон нужного размера. Затем на месте будущ их ручек крепят направляющие палочки и выполняют простым плетением белыми прутьями еще 10— 11 рядов (7 0 м м ). После чего выплетают цветную веревочку в два прутика, завершают стенки корзины белыми прутьями веревочкой в три прутика. Отделка бортика и низа корзины. Верхушки стоячков отмачивают в воде. П летут кромку в три-четыре пары прутьев (см . рис. 39, 4 0 ). На доныш ко ставят 23 стоячка вдоль основных и закрепляют вере вочкой в два прутика. Заверш ают плетение третьей кромкой (см . рис. 3 7 ). К онцы прутьев подрезают. К орзинку ставят под груз до полного высыхания. 66
Ручку делают так же, как описано выше. При заплетке ручки с каждой стороны вместо двух белых ставят по два или более цветных прута. П осле сушки корзинку снаружи и изнутри покрывают лаком.
Плетение кашпо по модели (рис. 58) Каш по — декоративная вазочка для цветов, делают ее по модели, т. е оплетают непосредственно сам горшочек. П росветы в ажуре могут бы ть прямыми, ромбиком, крестиком. Применение цветного и белого материала придает изделию особ ую привлекательность. Для работы потребуются: круглое донышко из фанеры диаметром 100— 150 мм, толщиной 6 мм, в плоскости которого просверливают 26 отверстий диаметром 3,5— 4 мм, а в радиальном направлении ( с торц а) 26 отверстий диаметром 2,5— 3 мм, в качестве шаблона использую т горшочек вы сотой 130 мм, с доныш ком диаметром 80— 90 мм, диаметр верха — 140 мм, 26 стоячков для стенок длиной 300— 350 мм, толщиной 3— 3,5 мм; тонкие мягкие белые и цветные прутья для плетения веревочек; нож, шило, дрель, лобзик, бокорезы , бечевка, клей, лак. Если горшочек другого размера, соответственно изменяют диаметр фанерного донышка, количество отверстий в любом случае долж но быть четным. Например, в фанерном донышке диаметром 90 мм просверлива ю т 22 отверстия диаметром 3,5 мм в плоскости основания и 22 отверстия диаметром 2— 2,5 мм в радиальном направлении; высота горшкашаблона — 110 мм, диаметр донышка — 70, диаметр верха — 120 мм. Начало работы. В отверстия на плоскости фанерного донышка вставляют 26 стоячков. Д ля придания изделию правильной формы ставят горшочек на донышко, прутья собираю т в пучок и завязы вают бечевкой (ри с. 52, а — г ). Расстояние между стоячками долж но быть 4— 5 мм. Д ля их крепления проплетают три веревочки — первую и третью в три, а среднюю (ц в етн у ю ) в два прутика. П рутья обрезаю т с внутренней стороны изделия. Уплотняю т плетение шилом с загнутым стержнем. Плетение верхней части кашпо. О собое внимание обращ ают на положение стоячков: расстояние между ними долж но бы ть одинаковым, просветы — продольными. На высоте 80 мм проплетают одну веревочку в три прутика (ра боту начинают с тонких концов, которы е закрепляют еще одним рядом веревочки), затем цветную веревочку в два и белую в три прутика. Ровность плетения проверяют по верхнему бортику горшочка. Затем концы стоячков, не вынимая горшочка, замачивают и плетут четвертую кромку (см . рис. 3 8 ). Плетение кромки на донышке. Тонкие стоячки вставляют в радиаль ные (тор ц евы е) отверстия в фанерном донышке и заплетают кромку в три пары прутиков. Кашпо сушат, не вынимая горшочка. После сушки обрезаю т концы так, чтобы они прилегали к стоячкам внутри кашпо, и покрывают изделие лаком. 67
Дамская сумочка (ри с. 59, а) Д ля плетения п отребую тся: 4 палочки длиной 320 мм, диаметром 4— 5 мм, 11 коротких палочек длиной 200 мм, диаметром 4— 5 мм и 3 дополнительные палочки диаметром 4— 5 мм для крестовины; мелкие мягкие прутья для донышка и прутья для веревочек; 33 стоячка длиной 450— 500 мм, диаметром 5— 6 мм (прутья должны быть жесткими с маленькой сердцевиной) для каркаса; 66 прутиков длиной 350 мм, диаметром 2— 2,5 мм для послойного плетения стенок сумочки; прутья средней толщины для плетения стенок сумочки; 2 прута длиной 500 мм, диаметром 8— 10 мм для ручек; 4 половинные ленты из ивового прута для обмотки ручек; 4 отрезка проволоки диаметром 2— 2,5 мм, длиной 250— 300 мм для крепления ручек; 33 стоячка длиной 250— 300 мм, диаметром 2— 2,5 мм для кромки на донышке; шаблон или овальный обруч (см . рис. 1 9 ); ножи, шило, бокорезы , от вертка, 2 шурупа, шпагат, клей. Плетение сумочки. Весь материал, подготовленный для работы, замачивают в воде. Для овального донышка сумочки нужны 4 длинные палочки, 11 поперечных и 3 дополнительные. Всего долж но быть 33 конца. Д вумя шурупами крепят доныш ко к шаблону. Заостренными концами вставляют 33 стоячка (каж ды й к палочке) в пазы, проде ланные шилом, сжимают их круглогубцами у самого края донышка, затем поднимают вверх и связы вают концы бечевкой. Оплетают стоячки у основания двумя рядами веревочки в три прутика. Стенки выполняют простым плетением на вы соту 60 мм и делают один ряд веревочкой в три прутика. Затем приступают к послойному плетению, подставляя под каж дую стойку по два прутика вершинными концами (см . рис. 3 0 ), и заплетают прутья на всю их длину. После чего делают один ряд веревочкой в три прутика, а затем 6 — 7 рядов простым плетением. Закрепляют работу веревочкой в три прутика. С двух сторон симметрично крепят петли из проволоки для ручек (ри с. 59, б ) , затем, не вынимая шаблон, замачивают макушки стоячков и делают кромку «коса» в четыре пары прутиков. В доныш ко вставляют 33 стоячка, закрепляя их, плетут один ряд веревочкой в два прутика и после увлажнения стоячков делают третью кромку. О ставляю т сумочку с шаблоном до высыхания. Ручки делают из свежего или хорош о вымоченного прута. Для чего выгибают две дужки, срезают их концы до половины толщины (ри с. 59, в), загибают в петли, связывают тонкой бечевкой и сушат (ри с. 59, г). После просуш ки надевают дужки на петли и закрепляют ивовыми лентами (см . рис. 5 9 ). Затем снимают шаблон, подрезают концы прутьев и покрывают изделие лаком.
Рис. 58. Кашпо
Рис. 59. Дамская сумочка: а — общий вид; б — петля из проволоки для ручки; в — заостренный конец ручки: I — дужка
Корзина хозяйственная (рис. 60) Размеры: высота — 230— 240 мм, длина донышка — 270, ширина — 150, длина верха — 320, ширина — 230 мм. Для крестовины потребуются: 4 палочки длиной 350 мм, диаметром 5,5 мм; 8 палочек длиной 200 мм, диаметром 4,5— 5 мм, 2 добавочные палочки длиной 120— 150 мм, диаметром 4,5— 5 мм; мелкие прутики для плетения основания. Для плетения корзины заготавливают: 26 стоячков длиной 650— 700 мм, диаметром 5— 5,5 мм для каркаса; 26 прутиков длиной 700 мм, диаметром 3,5— 4 мм для нижнего пояса; 52 прутика длиной 320 мм, диаметром 4 мм для верхнего пояса; длинные средней толщины прутья для веревочек; 2 прута длиной 750 мм, диаметром 12— 13 мм для ручек; 26 тонких стоячков для плетения нижней подставки корзины ; проволока длиной 900 мм, диаметром 2— 2,5 мм для крепления ручек; 4 половинные ленты для закрепления ручек; овальный обруч-ш аб лон длиной 320 мм, шириной 230 мм. Плетение корзины. На овальном донышке рядом с палочками шилом делают пазы и вставляют в них стоячки с большимч застругом, одновременно заправляют проволоку для крепления ручек. П однимают стоячки вверх вместе с проволокой, надевают обруч-ш аблон, закрепля ют основание корзины одной веревочкой в три прутика и приступают к послойному плетению. П ервую полосу плетут одним прутиком, начиная с тонкого конца, и закрепляют ее тремя рядами веревочки в три прутика. В торую полосу плетут парой прутиков, начиная с толсты х концов, выплетают одну веревочку в три прутика. Заверш ают плетение кромкой в четыре пары прутиков, предварительно сделав петли.из проволоки для ручек (см . рис. 59, б ) . И з мелких стоячков у донышка заплетают кромку в три пары прутиков. Стенки корзины можно выполнить простым плетением.
Белорусская корзинка (рис. 61, а) О сновой белорусской корзинки, в отличие от корзин, которые плетут с донышка, является каркас. Е го правильная форма и плоскость внизу делают корзинку более устойчивой. Сначала необходимо сде лать этот каркас, а затем приступать непосредственно к плетению из делия. Для плетения потребуются: 2 прута длиной 1000 мм, диаметром 10— 12 мм для обручей; 10 прутьев длиной 500— 550 мм, диаметром 5— 6 мм для продольных стоячков (р е б е р ); прутья диаметром 4— 4,5 мм для лент; прутья тонкие и средней толщины для плетения стенок; 10— 12 половинных лент длиной 500— 600 мм; нож, шило, бокорезы , шпагат, мелкие гвозди, лак, клей. Подготовка каркаса. Сначала из ивовых прутьев делают обручи: 70
Рис. 61. Белорус ская корзинка: а — общий вид; б — скрепление обручей; в — л — порядок плетения звездочки; с — плетение каркаса
Рис. 61. Продолжение
е
один диаметром 260 мм, другой — 230 мм. О бручи вставляют крестнакрест один в другой и скрепляют. М есто соединения концов вертикального обруча долж но быть внизу. Стыки малого (гори зон тал ь ного) и больш ого (вертикального) обручей крепят гвоздиками (ри с. 61, б )’
Для большей устойчивости корзинки нижней части обруча придают плоскую форму. Для этого обруч стягивают шпагатом, предварительно придав его основанию плоскую форму. П лоскость внизу не должна бы ть очень большой, иначе корзинка потеряет симметричность. Скрепленные обручи оставляют до полного высыхания. После просушки места скрепления обручей несколько раз плотно оплетают прутом или лентой, делая так называемые звездочки. Для чего обручи ставят на колени будущ ей ручкой от себя. Тонкий конец ленты заводят снизу с обратной стороны обручей и обворачивают малый обруч сверху (ри с. 61, в) . П рижимают конец ленты и продолж а ют выплетать звездочку, обводя сверху и снизу скрещение обручей (рис. 61, г ). Н овую ленту подкладывают под конец предыдущей и продолж ают работу. Сделав 7— 8 витков, конец ленты привязывают к обручу. Заверш ают звездочку оплеткой целым прутом для придания прочности, конец его закрепляют на вертикальном обруче внизу (рис. 61, д ). Плетение каркаса. Первые две палочки длиной 540— 550 мм вымачивают и заостряю т с внутренней стороны . При установке полочек (р е б е р ) может измениться форма малого обруча, поэтому предвари тельно поперек него крепят деревянную распорку (рис. 61, е ). Палочки вставляют в места крепления (зв езд оч к и ), придавая им форму нижней (п л оск ой ) части вертикального обруча. Следующ ие две палочки должны быть длиннее, их также вставляют в звездочки параллельно первым, чтобы ребра в нижней части каркаса образовали плоскость, необходимую для устойчивости корзин. Таким образом вставляют по пять палочек с каждой стороны . О т правильного выбора длины палочек и точности придаваемой им формы зависит симметричность корзинки. После чего для удобства плетения и сохранения формы все ребра в центре связы ваю т мягкой проволокой или шпагатом (см . рис. 61, е ). В дальнейшем при оплетке каркаса ребра будут играть роль стоячков. Для закрепления ребер и формы каркаса с обеих сторон от звездочек делают несколько рядов простым плетением. Затем снимают проволоку и продолж ают плести корзину, выдерживая равное расстояние между ребрами и постоянно контролируя сохранение формы изделия. Концы прутьев обрезаю т только внутри корзинки. В процессе работы заплетенные края смещаются: наверху возле обруча донышка они ближе и дальше — в середине. Ч тобы выровнять плетение, с каждой стороны заплетают по два прутика, не доводя их до малого обруча. Плетение цветными прутиками. Очень красочно и привлекательно выглядит корзинка, если ее выплетают белыми и цветными прутьями. Например, звездочки можно выполнить поочередно двумя рядами 74
белых и двумя рядами цветных лент, а в стенках корзины выплести по две белых и цветных полосы.
Корзинка для цветов (рис. 62, а) Размеры корзинки: высота без б о р д ю р а — 120 мм, диаметр донышка — 115 мм, диаметр верха — 150, высота бордю ра — 55 мм. Для плетения донышка потребуются: 8 палочек для крестовины 4 X 4 длиной 160— 180 мм, диаметром 4 мм и одна дополнительная. В место плетеного донышка можно использовать фанерный круг диаметром 115 мм, в плоскости и радиальном направлении просверлива ют по 17 отверстий диаметром соответственно 4 и 2,5 мм. Для работы потребуются: 34 стоячка длиной 400 мм, диаметром 4 мм для каркаса; 17 стоячков длиной 200— 250 мм, диаметром 2— 2,5 мм для кромки донышка; прутики для плетения стенок и веревочек; обруч-ш аблон диаметром 180 мм или горшочек, 2 прута длиной 850 мм, диаметром 5— 6 мм для ручки; нож, шило, бокорезы , дрель, шпагат, клей. Плетение стенок корзинки. Комлевые концы прутьев, подго товленные для стоячков, застругивают и заостренными концами плотно вставляют в доныш ко рядом с палочками (ри с. 62, б ) . Ставят груз, затем загибают все стоячки вверх, связы вают их концы и оплетают стоячки веревочкой в три прутика. Для того чтобы при плетении стоячки не расходились и сохранялась форма корзинки, вставляют обруч-ш аблон нужного размера и крепят его к четырем стоячкам, расположенным по диагонали. Далее простым плетением выплетают стенки корзины на высоту 30 мм (5 р ядов). Затем возле каждого основного стоячка с правой стороны проделывают шилом пазы, вставляют 17 дополнительных стоячков и оплетают их веревочкой в три прутика. О ставляют просвет 50 мм, разводят стоячки по одному, заплетая веревочкой в два прутика (ри с. 62, в ), и продолж ают плести еще четыре ряда. Выравнивают стоячки, чтобы корзинка расширялась кверху равномерно. Закрепляют работу веревочкой в три прутика. П о окончании плетения стенки со всех сторон должны бы ть одинаковой высоты. Плетение бордюра углом. Работу начинают с л ю бого стоячка: загибают его за пять стоячков снаружи и вставляют заостренным концом слева от шестого стоячка. Таким образом загибают все стоячки. На донышке корзинки рядом с основными стоячками ставят 17 мелких прутиков, закрепляют их веревочкой в два прутика и делают кромку в три пары прутиков (р и с. 3 9 ). Изготовление ручки. С диаметрально противополож ных сторон Корзинки в нижний поясок рядом со стоячком вставляют заостренные Концы прутьев, загнутых дугой на высоте 410— 420 мм от донышка. Прутья переплетают между собой и тонкими концами крепят ручку к стоячку ниже пояска корзинки. После просушки изделие лакируют. 75
Рис. 62. Корзинка для цветов: а — общий вид; б — установка стоячков; в — разведение стоячков
Рис. 62. Продолжение
Корзинка под бутылку (ри с. 63, а ) Для плетения п отребую тся: 28 стоячков длиной 630— 650 мм, диаметром 3,5— 4 мм для каркаса (материал должен быть плотным с маленькой сердц евин ой); тонкий, гибкий прут для стенок; 28 стоячков длиной 250 мм, диаметром 2,5 мм для кромки донышка; прут длиной 300— 320 мм, диаметром 8— 10 мм для ручки; деревянная болванка; половинные ленты для оплетки ручки; 6 палочек длиной 130— 140 мм, диаметром 3,5— 4 мм и 2 дополнительные палочки для крестовины ЗХ 3; тонкие прутики для плетения основания; нож, шило с загнутым стержнем, бокорезы , дрель, лобзик, маленькие гвозди, шурупы, отвертка, шпагат, клей, лак, груз. Для корзины делают круглое доныш ко из крестовины З Х 3, подставляют 2 дополнительные палочки, чтобы получилось 14 концов. Д оны ш ко можно сделать также из пятислойной фанеры диаметром 100 мм. В плоскости кружка просверливают 28 отверстий диаметром 2,5— 3 мм, а в торцевой части 28 отверстий диаметром 1,5— 2 мм. П одготовка материала. Комельковые концы стоячков заостряю т на малый срез. Перед плетением все прутья замачивают в воде, в том числе и предназначенные для нарезки лент. И з ивового прута делают дуж ку для ручки высотой 110 мм, расстояние между концами 120 мм. Концы застругивают на ус с внутренней стороны и сушат. Д оны ш ко ш урупом крепят к болванке. Вставляют в него заостренными концами 28 стоячков, по два в каждой палочке. При этом стоячки проминают шилом у самого основания донышка. Затем их поднимают вверх, собираю т в пучок и связы вают бечевкой. Д ля закрепления стоячков у основания делают один ряд веревочкой в три прутика. Плетение стенок корзинки. Работу выполняют с ажурным просветом прямым плетением и ромбиком, количество стоячков четное. Сначала плетут 4 ряда веревочкой в дба и один ряд в три прутика, уплотняют плетение шилом, оставляют прямой просвет шириной 40 мм. Затем выравнивают стоячки и закрепляют их веревочкой в два прутика. Следует помнить, что после лю бого просвета начинать плетение надо с тонких концов, оставляя при этом кончики в 30— 40 мм для заплетки следующими рядами. П родолж ая плетение веревочкой в два прутика, делают 4— 5 рядов и один ряд веревочкой в три прутика. П л е т е н и е а ж у р а р о м б и к о м . Развязы ваю т концы стоячков. На высоте 15 мм от среднего пояска на болванке предусмотрена разметка, по которой делают первую загибку стоячков. Д ля чего каждые два стоячка кладут друг на друга крест-накрест (левый прут должен бы ть сверху) и на уровне разметки забивают в болванку гвоздик, чтобы зафиксировать стоячки в этом положении (ри с. 63, б ) . Таким образом попарно перекрещивают все стоячки. Затем из каждой пары прутиков левый пропускают под правым и забивают гвоздики на линии следующей разметки (ри с. 63, в ). Так 78
Рис. 63. Корзинка под бутылку:
4 1 5 -4 2 0
а — общий вид; б — 1-й вариант плетения ажура ромбиком; в — 2-й вариант плетения ажура ромбиком; г — завершение ажура; д — подготовка стоячков для плетения ручки; е — установка дужки; ж — оплетка ручки
Рис. 63. Окончание
выплетают необходимое количество рядов ажура. Продолжая выпле тать ромбики, надо сделать так, чтобы каждый из стоячков на верхней отметке перекрещивал третий от него стоячок, затем их закрепляют гвоздиком (р и с. 63, г ). Стоячки ставят вертикально, макушки вверху связывают шпагатом. Опытные плетельщики при выполнении ажура не пользуются гвоздиками, выдерживая «на глаз» нужный размер. Стоячки разводят по одному и выплетают тонкими концами 4 ряда веревочкой в два прутика. Заверш ают стенки корзинки веревочкой в три прутика. Плетение ручки. Стоячки делят на две части (п о 14 ш т.) и на высоте 160 мм завязы вают тонким шпагатом (ри с. 63, д ). На высоте 415— 420 мм от донышка крепят дуж ку (ри с. 63, е ). Концы прутьев уплотняют по изгибу дужки. С каждой стороны должно проходить не менее пяти прутьев, остальные обрезаю т так, чтобы они попали в заплетку ленты. П еревязывают укладку прутиков по дужке ниткой и плотно выплетают лентой (ри с. 63, ж ). Оплетку начинают и кончают тонкими концами лент. Снизу корзинки рядом с основными стоячками проделывают проходы шилом, вставляют в них мелкие прутья и делают кромку в три пары прутиков. К огда корзинка высохнет, вынимают болванку. П одрезаю т концы прутьев и лент. Ручку промазывают клеем и покрывают изделие лаком в два слоя.
Сухарница (ри с. 6 4 ) Размеры сухарницы: диаметр донышка — 150 мм, высота стенки — 70, диаметр верха — 220 мм (п о ш аблону). Для плетения потребую тся: 8 палочек длиной 170— 180 мм, диаметром 4,5— 5 мм для крестовины 4 Х 4 и 3 дополнительные палочки; мелкий прутик для заплетки крестовины; 19 стоячков длиной 350— 400 мм, диаметром 3— 3,5 мм для каркаса; 19 стоячков длиной 200— 250 мм, диаметром 2— 2,5 мм для кромки донышка; мелкий прут для стенок и средней толщины для веревочек; фанера-шаблон диаметром 220 мм, высотой 65 мм; нож, шило, бокорезы , дрель, лобзик, отвертка, 2 шурупа, тонкая бечевка, груз, лак. П одготовка материала. Перед плетением комельковые концы стоячков заостряют. Все прутья замачивают. Делают доныш ко 4 Х 4 и ставят 3 дополнительные палочки. Подготовленное доныш ко шурупом крепят к деревянной подставке. Заостренные концы стоячков вставляют в доныш ко рядом с палочками, предварительно проделав проходы шилом. Ч тобы стоячки не ломались, их сжимают у самого края основания сухарницы круглогубцами. К деревянной подставке шурупом крепят фанеру-шаблон. К ладут сверху шаблона груз, концы загнутых стоячков поднимают вверх, собирают вместе и связывают. При этом следят, чтобы они не сломались о край фанеры-шаблона. 82
Плетение стенок и кромок. Закрепляют стоячки у основания веревочкой в три прутика и выплетают 8— 9 рядов (5 0 — 60 мм) простым плетением. Расстояние между стоячками долж но быть одинаковым по всей окруж ности сухарницы. Затем плетение уплотняют шилом и закрепляют веревочкой в два прутика. Макушки стоячков вымачивают и завершают работу третьей кромкой. Сухарницу поворачивают вверх дном, вставляют по периметру стоячки меньшего размера, заплетают их веревочкой в два прутика и делают первую кромку. Готовую сухарницу ставят под груз до полного высыхания. После сушки вынимают шаблон-фанеру, обрезаю т все концы прутиков и покрывают изделие лаком.
Фруктовница с послойным плетением (рис. 65) Размеры фруктовницы: диаметр донышка — 150 мм, диаметр верха — 200, высота без бордю ра — 75, высота бордюра углом — 40 мм. Для плетения потребуются: 8 палочек длиной 170— 180 мм, диаметром 4—4,5 для крестовины; 5 дополнительных палочек и тонкий прутик для донышка; 21 стоячок длиной 450— 500 мм, диаметром 4,5— 5 мм для каркаса; 21 стоячок длиной 250— 300 мм, диаметром 2— 2,5 мм для кромки нижней части изделия; 42 прутика длиной 320 мм, диаметром 3,5— 4 мм для послойного плетения; тонкий мягкий прут для веревочек; прут длиной 500— 550 мм, диаметром 10— 12 мм для обруча-ш аблона; нож, шило, бокорезы , бечевка, груз, клей, лак. Подготовка к работе! Стоячки для каркаса заостряют на малый срез. Д ля послойного плетения стенок подбираю т прутья одинаковой длины, толщины и ж есткости. Д елают обруч-ш аблон диаметром 250 мм. П летут донышко 4 Х 4, ставят четыре дополнительные палочки, выплетают две веревочки в два прутика, ставят пятую палочку (всего 21 конец) и заплетают до нужного диаметра. Плетение стенок. Приступая к изготовлению каркаса, кромку донышка смачивают, кладут лицевой стороной вверх и ставят груз. В доныш ко рядом с палочками вставляют заостренные концы стоячков. П однимают их вверх, предварительно сжав шилом у самого края донышка, надевают на них обруч-ш аблон и крепят его к четырем диаметрально противоположным стоячкам. Затем оплетают все стоячки веревочкой в три прутика. После уплотнения веревочки приступают к послойному плетению двумя прутиками, начиная с тонких концов. При этом можно использовать цветные и белые прутья. Выплетают стенки фруктовницы на всю длину прутиков, обрезаю т концы и закрепляют одной веревочкой в три прутика. Плетение бордюра и кромки. Снимают обруч-ш аблон и увлажняют макушки стоячков. З аводят любой стоячок за три соседних стоячка с внутренней стороны и на высоте 40 мм загибают углом, з ао стр ен н ы й 84
конец вставляют возле четвертого стоячка, предварительно проделав проход шилом. Таким образом выполняют бордю р по всей окруж ности изделия. Начинающий плетельщик должен постоянно измерять высоту угла бордю ра, иначе изделие будет кривым. В доныш ко фруктовницы вставляют короткие стоячки и закрепляют их веревочкой в два прутика. Заверш ают плетение третьей кромкой. Затем изделие сушат и покрывают лаком. Бордю р, так же как и послойное плетение, можно выполнять прутьями двух цветов, для чего после плетения стенок к стоячкам добавляют дополнительные (ц ветн ы е) прутья, которы е поочередно со стоячками загибают углом.
Ваза конусная (рис. 66) Т а к ую вазу можно сделать в зависимости от назначения небольшого размера или высокой — напольной. Выполняют ее различными видами плетения: простым, в шахматку, послойным, спиральным и веревочкой в два прутика. Стенки выплетают ажуром (прямы е, крестиком, ромбиком или реш еткой). Верх оформляют простой кромкой или бордю ром (углом, овалом или волнисты м). Если освоить технологию плетения одной конусной вазы, то можно делать и другие, изменяя их размер, рисунок плетения стенок и бордю ра. Ваза со сплошным плетением (ри с. 66, а). Размеры : высота без бордю ра — 320 мм, диаметр внизу — 140, вверху — 120, высота овального бордюра — 60 мм. Д л я п л е т е н и я п о т р е б у ю т с я : фанерный диск диаметром 80 мм для донышка; две конусные болванки большой и малой высоты (см . рис. 17, а, б ) ; 19 стоячков длиной 550— 600 мм, диаметром 4 мм для каркаса; 19 стоячков длиной 250— 300 мм, диаметром 2,5 мм для кромки нижней части вазы; прутья тонкие для стенок и средней толщины для веревочек; нож, шило, бокорезы , дрель, лобзик, 2 шурупа длиной 30— 35 мм, клей, лак, шпагат. П о д г о т о в к а к р а б о т е . В плоскости фанерного диска про сверливают 19 отверстий диаметром 2,5— 3 мм и готовят стоячки для каркаса. Фанерное доныш ко снимают с готового изделия, поэтому диаметр комельковой части стоячков должен бы ть меньше, чем отверстия в фанерном донышке. П л е т е н и е с т е н о к . Стоячки вставляют в отверстия, остав ляя комельки длиной 80— 90 мм, больш ую болванку (ри с. 66, б ) крепят шурупом к фанерному основанию. Макушки стоячков поднимают вверх и завязывают, а у основания выплетают один ряд веревочкой в три прутика, затем, начиная с тонких прутиков, выплетают всю вазу простым плетением до нужной высоты (2 3 0 — 240 мм ), закрепляют стенки изделия одним рядом веревочки в три прутика и заканчивают работу бордю ром . 85
П л е т е н и е б о р д ю р а . Сначала увлажняют макушки стоячков. Затем любым стоячком огибают снаружи три соседних и пропускают слева от четвертого стоячка, обрезав бокорезом конец с припуском 13— 15 мм. 11осле чего заостряю т с внутренней стороны кончик прутика и вставляют его в отверстие, сделанное шилом в бортике вазы. Так продолж ают загибку стоячков по всей окруж ности изделия, постоянно измеряя вы соту бордюра. Затем снимают фанерное донышко, смачивают комельковые кончики и крепят малую болванку. Расправляют веером концы комельков и плотно проплетают 2 ряда веревочкой в два прутика. О с н о в а н и е в а з ы завершают простым плетением и закрепляют веревочкой в два прутика. О бр езаю т оставшиеся концы комельков, подставляют по периметру донышка более тонкие стоячки и плетут кромку в три прутика. П осле полного высыхания вынимают болванки, обрезаю т концы прутиков внутри вазы и концы бордюра, промазывают бесцветным клеем и покрывают изделие лаком. Отверстие, оставшееся на месте шаблона, закрывают отдельно выплетенным маленьким донышком, равным по размеру фанерному шаблону. Ваза конусная с послойным плетением. Для плетения потребую тся 38 прутиков одинаковой ж есткости длиной 400 мм, диаметром 2,5— 3 мм. Приспособления и инструменты такие же, как для предыдущей вазы. Работу начинают с тонких концов, заплетая прутья парами на всю длину. В остальном технология работы точно такая же, как и при плетении вазы конусной со сплошным плетением. Ваза конусная с ажурными стенками (ри с. 66, г). Изготовление этой вазы отличается от предыдущих тем, что здесь необходимо выплести несколько рядов ажура ромбиком, а фанерное доныш ко диаметром 80 мм долж но иметь четное число отверстий (например, 2 0 ), просверленных в плоскости. Д л я п л е т е н и я п о т р е б у ю т с я : 20 стоячков длиной 550— 600 мм, диаметром 4 мм для каркаса; 20 дополнительных стоячков длиной 400 мм, диаметром 3 мм для ажура; 20 стоячков длиной 250 мм, диаметром 2 мм для подставки; тонкие прутья для плетения стенок и веревочек; инструменты и приспособления такие же. П л е т е н и е в а з ы начинают с изготовления донышка. Стоячки вставляют в отверстия фанерного диска, а к нему крепят шурупом больш ую болванку. Макушки стоячков собирают в пучок и связывают. Далее у фанерного основания выплетают 4 ряда веревочки в два прутика. О ставляют прямой продольный просвет в 55 мм и плетут еще 3 ряда веревочкой в два прутика. Слева от каждого стоячка шилом делают проход и вставляют в них 20 дополнительных стоячков. Закрепляют плетение двумя рядами веревочки в два прутика. Затем развязывают макушки стоячков и выплетают ажур ромбиком на вы соту 110 мм. После чего делают 6 рядов веревочкой в два прутика и завершают работу бордю ром в два прутика. 87
Снимают фанерное донышко, смачивают комельковые концы, крепят шурупом малую болванку и равномерно (веером ) распределяют комельки по окруж ности. Далее проплетают 5 рядов веревочкой в два прутика, оставляют прямой просвет в 3 мм и продолжают плетение веревочкой в два прутика до нужного диаметра. П одрезаю т камелько вые концы, вставляют 20 более тонких стоячков и завершают плетение кромкой в три пары прутиков. В прямой просвет в нижней части вазы подставляют по одной палочке. После высыхания вынимают болванки, обрезаю т прутья и покрывают изделие двумя слоями лака. Ваза конусная с цветными прутиками. Ваза с ажурными стенками выглядит особенно нарядно, если начинают и заканчивают пояски на стенках вазы веревочкой в два прутика, выполненной цветным материалом. М ож н о также заплести стенки до половины высоты и подставить к белым стоячкам цветные, чтобы выполнить ажур ромбиком и бор д ю р парными — цветными и белыми прутьями. В основание вазы в прямой просвет подставляют по цветной палочке и завершают плетение цветной кромкой в три пары прутиков. Ваза со спиральным плетением (ри с. 66, в). Для плетения потребую тся: фанерный диск диаметром 80 мм для донышка (в плоскости диска долж но быть 23 отверстия диаметром 3,5 м м ); 23 стоячка длиной 550— 600 мм, диаметром 3,5 мм для каркаса; 46 стоячков длиной 300— 350 мм, диаметром 2 мм для бордю ра и кромки в нижней части изделия; мелкие средней толщины прутья для плетения стенок; остальной материал, приспособления и инстру менты — те же, что и для предыдущих изделий. Каркас делают так же, как для вазы со сплошным плетением. Стенки вазы начинают выполнять с тонкого конца прутьев. Оплетают пять стоячков простым плетением, а три стоячка огибают снаружи. Так плетут до верха. В процессе работы толщину прутиков постепенно увеличивают. Завершая плетение, подставляют дополнительные ст о ячки к каждому основному и оформляют овальный бордю р в два прутика. П орядок выполнения нижней части вазы такой же, как сказано выше: работу ведут тонкими концами прутиков, продолжая плетение спирали вниз до нужного диаметра. Затем подставляют дополнитель ные стоячки, закрепляют веревочкой в два прутика и завершают третьей кромкой. После высыхания изделия обрезаю т кончики прутьев и покрывают двумя слоями лака.
Ваза ажурная четырехгранная (рис. 67, а) Размеры вазы: высота — 270— 280 мм, диаметр донышка — 70— 80, вверху длина стороны — 120 мм. Для плетения потребуются: 8 палочек длиной 120 мм, диаметром 3,5 мм для крестовины 4 X 4 и одна дополнительная палочка; мелкий прутик для плетения основания; 32 стоячка длиной 550 мм, диаметром
3,5— 4 мм для каркаса; 32 тонких стоячка длиной 300 мм, диаметром 3 мм для нижней части изделия; прутья тонкой и средней толщины для стенок; большой и малый шаблон (см . рис. 1 6); нож, шило, бокорезы , отвертка, 2 шурупа длиной 350— 400 мм, клей, лак. Подготовка к работе. Выплетают доныш ко диаметром 80 мм. Затем шурупом крепят его к шаблону. С тоячки комельками вставляют в донышко (п о одному к каждой палочке), поднимают их макушки вверх и связывают. Затем стоячки у основания оплетают двумя рядами веревочки в три прутика. Для повышения прочности вазы и удобства плетения ажура ставят 17 дополнительных стоячков (ри с. 67, б ) , чтобы получилось 17 парных стоячков. Стенки выполняют простым плетением на вы соту 130 мм. Закрепля ют работу веревочкой в три прутика и выплетают ажур решеткой. Для чего, начиная с любой пары, правый прутик загибают вправо, а справа от него из четвертой пары левый прутик загибают влево, на высоте 60— 65 мм в болванку забивают гвоздик и соединяют два загнутых прута, причем правый пропускают сверху левого (ри с. 67, в). Остальные стоячки загибают и крепят в той же последовательности, завершают ажур веревочкой в два прутика. В результате получилось нечетное число концов (1 7 пар). Так парами продолж ают выплетать простое плетение на вы соту 70 мм и закрепляют, сделав один ряд веревочкой в три прутика. Затем замачивают кончики стоячков (не вынимая болванку), по овальному закруглению шаблона проплетают веревочку в два прутика, чтобы получилось четырехгранное завершение вазы. Стоячки раздвига ют по одному для создания ажурных просветов (рис. 67, г ). Заверш ают плетение кромкой в три пары прутиков. Плетение нижней части вазы. П одставляют по два тонких стоячка к каждой палочке. К донышку внутри вазы крепят малую болванку, предварительно положив небольш ую подставку из фанеры. При этом концы стоячков разводят веером, а затем попарно оплетают их веревочкой в два прутика (7 р я д ов). После чего оставляют просвет в 25 мм и опять выполняют веревочку в два прутика, но при этом разводят стоячки по одному. Заверш ают плетение кромкой в три пары прутьев. П осле обрезки концов высуш енную вазу покрывают лаком. Верхнюю часть вазы можно оформить бордю ром из парных прутьев (см . рис. 4 4 ). Вместо круглой малой болванки внизу можно поставить квадратную (разм еры сторон внизу 140Х 140 мм) с овальными углами, а высота и диаметр такие же, как у круглой болванки.
« ^
Рис. 67. Продолжение
к • : г - ± \
Рис. 68. Ваза конусная с шаровидным основанием
\V
\ »
Ваза конусная с шаровидным основанием (рис. 68) Ш аровидное основание выплетают на специальной оправе. При выполнении конуса рекомендуется использовать разные виды простого и ажурного плетения, а заканчивать работу — кромкой или бордю ром. О собен но эффектно выглядит вазочка небольш ого размера с примене нием цветного материала. Для плетения потребуются: фанерный диск диаметром 80 мм для донышка; деревянная оправа из двух частей; 26 стоячков длиной 500 мм, диаметром 4— 5 мм для каркаса; 52 прутика длиной 350 мм, диаметром 2 мм для послойного плетения двойными прутиками; 30 стоячков длиной 250— 300 мм, диаметром 1,5— 2 мм для нижней кромки; мелкие прутики для плетения стенок вазы и веревочек; нож, шило, бокорезы, лобзик, дрель, отвертка, клей, лак, шпагат, 2 шурупа. Подготовка к работе. Прежде чем приступить к плетению, необходимо в фанерном диске с торцевой стороны просверлить 26 отверстий диаметром 4— 5 мм и одно отверстие в центре. Нижняя часть оправы должна бы ть в форме полусферы, низ которой имеет плоскость диаметром 80— 100 мм. К этой плоскости крепят фанерную основу. Высота оправы — 60— 70 мм, ди ам етр— 120 мм (см . рис. 53, а). В центре на глубину 5— 10 мм (свер ху и сн и зу) сверлят отверстия диаметром 2— 2,5 мм. Нижняя оправа после плетения остается в изделии. Высота верхней части оправы конусной формы — 230 мм, диаметр снизу — 80, сверху — 110 мм. О бе части соединяют в центре гвоздем, причем так, чтобы можно бы ло свободн о ставить и снимать их (см . рис. 53, б ) . Сначала фанерное доныш ко шурупом крепят к оправе. Стоячки комельками вставляют в отверстия диска, а затем устанавливают конусную болванку. Стоячки прогибают по окруж ности оправы, чтобы они облегали ее, и только после этого поднимают их вверх, связы ваю т над узким концом конусной болванки и оставляют до высыхания (см . рис. 53, в ). После высыхания стоячки завязывают выше конусной оправы и закрег'/ляют их у основания двумя рядами веревочки в три прутика. Плетение стенок. Выполняют послойное плетение в два прутика, начиная с тонких концов, и заплетают веревочкой в два прутика горлышко вазы. П о мере уменьшения диаметра обрезаю т лю бы х два стоячка и на вы соте 120 мм плетение закрепляют веревочкой в три прутика. Далее делают ажурный просвет ромбиком на вы соту 90 мм и плетут верхний поясок шириной 20 мм. Начинают плетение пояска веревочкой в два, а заканчивают веревочкой в три прутика. Верх оформляют овальным бордю ром высотой 60 мм. Для плетения основания вазы обрезаю т стоячки по периметру фанерного донышка, вынимают его, подставляют дополнительные 92
стоячки и закрепляют их веревочкой в два прутика. Заверш ают плетение третьей кромкой. После просушки обрезаю т прутики и покрывают изделие лаком. Ваза конусная из цветных и белых прутьев. Д ля плетения потребую тся: 26 стоячков длиной 500 мм, диаметром 4— 5 мм для кар каса; 52 цветных прутика длиной 350 мм, диаметром 2 мм для пос лойного плетения; мелкие цветные и белые прутики для стенок и веревочек. П орядок плетения такой же, как и при выполнении одноцветной вазы, только заплетку шаровидного основания делают цветными прутьями. П ослойное плетение начинают парными прутиками с тонких концов и плетут на всю их длину. Затем закрепляют веревочкой в два прутика белым и цветным материалом. А ж урны й просвет ромби ком делают вы сотой 90 мм. Плетение пояска начинают и заканчивают веревочками из белого прута, а середину выплетают из цветного. Верх вазы и нижнюю кромку заверш ают белыми прутьями. П о этой технологии можно сделать больш ую напольную вазу, но для этого надо сделать расклинивающий шаблон (оп р а в у ).
Ваза на ножке (рис. 69, а) О сновой для этой вазы служ ит деревянный конус цилиндрической формы, на котором плетут ножку. Размеры вазы: высота — 200 мм, диаметр вверху — 230, внизу — 130— 140, высота ножки — 80, высота основания ножки — 30 мм. Д ля плетения потребую тся: болванка плоская — усеченный дере вянный конус длиной 80 мм, диаметр нижней стороны — 35 мм, верхней — 25 мм для ножки (ри с. 54, б ) ; 27 стоячков длиной 450— 500 мм, диаметром 35 мм для каркаса; 27 дополнительных цветных стоячков длиной 300 мм, диаметром 3 мм для оформления кромки верха; 27 цветных прутиков для подставки; мелкие прутья для плетения чаши и нижней части вазы; шаблон (обы чная миска) диаметром 220 мм; нож, шило, бокорезы , отвертка, пилка, проволока, клей, лак, шуруп длиной 15— 20 мм. Подготовка к работе. Сначала 27 стоячков плотно укладывают вдоль конуса и крепят аптекарской резинкой, а по краям конуса-оправы концы их связы ваю т проволокой. Комельковые кончики стоячков должны выступать на 60 мм от нижней кромки конуса (см . рис. 54, а). В верхней части конуса отгибают стоячки веером и закрепляют шурупом миску-шаблон. Макушки стоячков поднимают вверх и связы вают. Плетение стенок. Н иж ню ю часть чаши заплетают простым плетением на вы соту 40 мм. Затем справа от каждого основного стоячка ставят дополнительные цветные и закрепляют веревочкой в два прутика. Разводят стоячки, оставляя просвет, и на высоте 40— 45 мм соединяют их парами — цветные с основными белыми, стоящими справа. Заплетают 2— 3 ряда веревочки в два прутика и обрезаю т 93
Рис. 69. Ваза на ножке: а — общий вид; б — болванка плоская
основные (б ел ы е) стоячки. Далее работу ведут цветными стоячками и завершают плетение кромкой в четыре пары прутиков. Выполнение нижней части вазы. Сначала стоячки замачивают, разводят веером и разжимают на плоской болванке. Заплетают подставку простым плетением до нужного диаметра. Затем ставят цветные мелкие стоячки и завершают работу кромкой в три прутика. П осле просушки снимают миску-шаблон, а конусную оправу вынимают из ножки, промазывают клеем и ставят на место. Д ля верха и низа ножки из тонких прутиков выплетают маленькие донышки. После высыхания клея снимают проволоку с ножки, обрезаю т концы прутьев и покрывают вазу лаком.
Хлебница ажурная в один прутик (рис. 70, а) Для плетения потребуются: круглое донышко диаметром 150 мм, крестовина 4 X 4 и три дополнительные палочки (всего на донышке 19 к о н ц о в ); 19 упругих, одинаковой толщины, с маленькой сердцевиной стоячков, длиной 550— 600 мм, диаметром 4— 5 мм;тонкие прутики для веревочек; болванка-шаблон (см . рис. 14); фанерная подставка диаметром 140 мм; нож, шило, отвертка, груз, шурупы длиной 20 мм, бечевка и лак. Подготовка к работе. Смачивают край донышка, чтобы не повредить плетение, и крепят его шурупом к болванке. Комлевые концы у стоячков застругивают ножом и плотно вставляют в донышко рядом с палочками. Ч тобы стоячки не сломались, сжимают их шилом или круглогубцами у самого основания, поднимают макушки вверх и связы вают. После чего оплетают стоячки у донышка веревочкой в три прутика и выполняют стенки в один прутик, на высоту 60— 65 мм. Плетение стенок. Л ю бой стоячок загибают дугообразно, обв о дят им два соседних снаружи, один изнутри и пропускают через веревочку между четвертым и пятым стоячками (ри с. 70, б ) . Таким образом загибают все стоячки. Во время работы их регулярно проти рают влажной тряпочкой. В ы соту загибки стоячков выравнивают по верхнему бортику болванки. Затем хлебницу переворачивают вверх дном и оплетают кончики стоячков веревочкой в два прутика. При этом стоячки оттягивают на себя, чтобы они заняли вертикальное положение. Заверш ают плетение низа изделия третьей кромкой. На готовое изделие ставят груз до полного высыхания. П осле чего снимают болванку, обрезаю т кончики прутьев, покрывают хлебницу лаком.
Рис. 7 /. Хлебница ажурная в два прутика
Хлебница ажурная в два прутика (рис. 71) Для плетения потребуются: доныш ко диаметром 150 мм (1 9 кон ц о в ); деревянная болванка-шаблон (см . рис. 1 4); 38 стоячков длиной 550— 600 мм, диаметром 4— 5 мм для стенок; прутья для веревочек. Технология плетения такая же, как и при выполнении хлебницы в один прутик, только к каждой палочке подставляют по два стоячка. Плетение ажурной стенки. Л ю бу ю пару прутиков сгибают в дугу, обводят две пары соседних стоячков снаружи, одну сзади и пропуска ют через один прутик веревочки между 4-й и 5-й парами стоячков. Заверш ают плетение третьей кромкой. П роверяют ровность кромки. Ставят груз до полного высыхания. П окрывают хлебницу лаком.
Хлебница ажурная в три прутика (рис. 72, а) Для плетения потребуются: доныш ко диаметром 150 мм (1 9 кон ц о в ), болванка-шаблон (см . рис. 1 4 ); 57 стоячков длиной 550— 600 мм, диаметром 4— 5 мм для стенок; тонкие прутья для веревочек, шуруп, шило, бокорезы , бечевка, лак. Закрепление стоячков в донышке. Один стоячок вставляют прямо в палочку, предварительно проделав проход шилом, а два других — слева и справа от палочки. Стенки выплетают ажуром так же, как и у предыдущ их хлебниц. М ож но выплетать их и так. Первые три стоячка загибают дугой, о б водят их снаружи двух соседних троек стоячков и изнутри три следую щих, пропускают через веревочку между четвертыми и пятыми тройка ми и т. д. О собен ность этой хлебницы заключается в том, что внизу плетут кромку «коса», которая придает хлебнице не только красивый вид, но и устойчивость. Плетение кромки «коса». В этом изделии стоячки не закрепляют веревочкой в два прутика, а после их увлажнения хлебницу ставят на колени и держат стоячками от себя, придав им горизонтальное положение. Затем тремя любыми стоячками справа налево огибают снаружи две тройки стоячков, а следую щ ую тройку — изнутри, концы выводят наружу (р и с. 72, б ) . Т а к ж е . загибают все остальные стоячки и все концы вы водят наружу. Затем уплотняют, выравнивают плетение и увлажняют прутья. После этого концы каждой тройки заправляют между четвертой и пятой тройками во внутрь и обрезаю т (ри с. 72, в) . П осле сушки снимают болванку, покрывают хлебницу лаком. Плетение цветными прутиками. Х лебни цу ажурную в три прутика можно плести и так: один стоячок цветной, два белых или два цветных, 97
один белый. При этом одиночный вставляют прямо в палочку.
стоячок
(цветной
или белы й)
Фруктовница ажурная (рис. 73) Размеры фруктовницы: диаметр донышка — 170 мм, высота от донышка — 100, диаметр верха — 330 мм. Д ля плетения потребую тся: круглое донышко диаметром 170 мм (крестовина 4 X 4 из 8 палочек длиной 220 мм, диаметром 5 м м ); мелкие прутья для плетения основания; 64 стоячка длиной 650— 700 мм, диаметром 3,5— 4 мм для стенок; тонкие прутья для веревочек; круж ок из фанеры диаметром 320 мм, пдоставка вы сотой 95 мм, диаметром 50— 60 мм. Подготовка к работе. Д оны ш ко точно по центру крепят шурупом к подставке. Возле каждой палочки вставляют по три стоячка, а один стоячок — прямо в палочку. Стоячки сжимают* шилом или кругло губцами у самого основания. После чего к подставке крепят фанерушаблон с гладким бортиком. Макушки стоячков поднимают вверх и связы вают. Расстояние между стоячками выравнивают и оплетают доныш ко у основания веревочкой в три прутика. При работе фруктовницу держат на коленях донышком к себе, плетение ведут слева направо. Плетение стенок. Для придания фруктовнице прочности и привле кательности ажурную стенку плетут в четыре прутика на высоту 100 мм. Четыре любых стоячка дугообразно загибают и обводят ими четыре соседних изнутри, следующ ие четыре — снаружи, еще четы ре — изнутри и снова снаружи, пропускают концы стоячков через веревочку между 5-й и 6-й четверкой стоячков. Таким образом загибают все остальные стоячки. А ж у р н у ю стенку выравнивают по бортику фанеры-шаблона. Н иж ню ю часть фруктовницы заплетают кромкой «коса». После полного высыхания снимают фанеру-шаблон, фруктовницу покрывают лаком. Плетение фруктовницы цветным и белым материалом. В донышко крепят по два цветных и два белых стоячка. На донышке плетут пояски и веревочки из цветного материала.
Настенное украшение (рис. 74, а) Для плетения потребуются: круглое доныш ко диаметром 120 мм из крестовины 3 X 3 (у основания долж но быть 12 к он ц ов ); 6 палочек длиной 150 мм, диаметром 4 мм для крестовины; 24 стоячка длиной 550 мм, диаметром 4 мм для основания; 24 прута длиной 450 мм, диаметром 4 мм и 48 цветных прутиков длиной 450 мм, диаметром 99
Р ис. 13. Фруктовница ажурная
Рис. 14. Настен ное украшение: а — общий вид; б — бордюр; / — 5 — стоячки
4 мм для бордю ра; мелкий материал средней толщины для основания; цветные прутья для веревочек; фанерный круг диаметром 250— 260 мм для придания плоскости изделию; нож, шило, бокорезы , груз, клей, лак. Тонкая проволока или бечевка. Плетение основания. Начинают работу с тонких концов веревочкой в два прутика и выплетают основание диаметром 120 мм. Затем обрезаю т концы, подставляют к каждой палочке по два стоячка длиной 550 мм и продолж ают заплетать веревочкой в два прутика. Для чего стоячки разводят по одному, чтобы получилось 24 конца. В середине основания проплетают цветным материалом два ряда веревочкой в два прутика. Далее работу ведут белыми прутьями до нужного диаметра (2 9 0 мм ). Теперь к каждой палочке подставляют с левой стороны по два цветных, а с правой — по два белых стоячка и закрепляют их цветным материалом веревочкой в три прутика. Д ля удобства плетения на основание кладут фанерный круг и придавливают грузом. Плетение бордюра. Б ордюр высотой 130 мм делают в четыре прутика. Для чего заготовку кладут на стол лицевой стороной вниз, работу ведут справа налево. Л юбыми четырьмя стоячками (о бв о д я т снизу четыре соседних, затем четыре — сверху и еще четыре — снизу, концы выводят наружу между 4 и 5 стоячками (ри с. 74, б ) . К онцы стоячков обрезаю т с припуском 3— 4 мм и привязывают их к основа нию ниткой или проволокой. Таким образом загибают все остальные прутики. Украшение ставят под груз. После полного высыхания концы стоячков подрезают, промазывают клеем и покрывают изделие лаком.
Круглая рамка с бордюром (рис. 75) Для плетения потребуются:" фанерный круг диаметром 180 мм, толщиной 5— 6 мм; 43 стоячка длиной 200— 250 мм; диаметром 3,5 мм для бордю ра; тонкие длинные прутья для веревочек; нож, шило, бокорезы , лобзик, дрель, плоскогубцы, линейка, клей, лак. С торцевой стороны фанерного круга на глубину 7— 8 мм просверливают 43 отверстия диаметром 3,5 мм. Расстояние между отверстиями 12— 15 мм. В отверстия вставляют стоячки комельковым концом и выплетают 2 ряда веревочкой в три прутика. Плетение бордюра. Л ю бой стоячок загибают дугой (вы сота 40 м м ), огибают им четыре соседних стоячка снаружи и вставляют за остренным концом с левой стороны от пятого. Таким образом загибают все стоячки. Д ля того чтобы получить ровный верх, нужно постоянно измерять вы соту дуги. После просушки кончики стоячков, вставленные в веревочку, промазывают бесцветным клеем и покрывают рамку лаком. Бордю р рамки можно выплетать разными способами, используя при этом цветные, неочищенные или отварные прутья.
Овальная рамка с бордюром для зеркала (рис. 76) Размер зеркала: длина — 800 мм, ширина — 420, толщина фа нерного основания — 10 мм. Для плетения потребуются: 74 стоячка длиной 400— 450 мм, диаметром 5 мм, 74 цветных стоячка длиной 400— 450 мм, диаметром 4,5— 5 мм для бордю ра; прутья белые и цветные длиной 600— 700 мм, диаметром 4,5— 5 мм для веревочек; нож, шило, бокорезы , дрель, груз, клей, лак, линейка. Подготовка к работе. О тделяю т зеркало от фанерного основания, на котором будет выплетен бордю р. Затем с торцевой стороны просверливают 74 отверстия диаметром 5 мм на глубину 18— 20 мм. Расстояние между ними — 25— 30 мм. Крепление стоячков. Ф анерное основание кладут на стол вверх той стороной, где бы ло зеркало. П одготовленные белые стоячки плотно вставляют в отверстия основания. Затем белым материалом оплетают стоячки веревочкой в три прутика и выполняют один ряд цветной веревочкой *в два прутика. С левой стороны к каждому основному стоячку подставляют по одному цветному и закрепляют их белым материалом веревочкой в три прутика. После чего приступают к плетению овального бордю ра вы сотой 65— 70 мм. Плетение бордюра. Работу ведут парными прутиками, размещая сверху цветной (см . рис. 4 4 ). Л ю бой парой стоячков огибаю т три соседние пары снаружи и концы их вставляют в веревочку с левой стороны от четвертой пары. К онцы стоячков предварительно заструги вают, а в веревочке делают шилом проходы. Таким образом загибают все пары стоячков. П осле завершения бордю ра и просушки стоячки закрепляют бесцветным клеем, покрывают изделие лаком и крепят зеркало.
Абажур (рис. 77, а) А ба ж у р состоит из двух отдельных частей. Первая часть конусная, вторая часть служит для рассеивания света. После завершения работы эту часть надевают на конусную. Для плетения конусной части потребуются: фанерный кружок толщиной 5 мм, диаметром 150 мм (в плоскости круга просверливают 37 отверстий диаметром 5 мм для стоячков и одно отверстие в центре диаметром 8 мм для металлического стержня электропатрона); фанерный круж ок диаметром 260 мм, в плоскости которого просверле но 37 отверстий диаметром 5 мм, а в центре — отверстие диаметром 10— 12 мм для деревянного стерж ня; деревянный стержень длиной 350 мм, диаметром 10— 12 мм, один конец стержня должен бы ть скошен, диаметр его — 8 мм; электропатрон с металлическим стерж103
*
нем-трубкой длиной 270— 280 мм; 37 стоячков длиной 550— 600 мм, диаметром 5 мм для каркаса; 37 цветных стоячков длиной 400— 450 мм, диаметром 3,5— 4 мм для бордю ра; длинные белые и цветные прутья для веревочек диаметром 3,5 мм: нож, шило бокорезы , пилка, дрель, отвертка, шуруп, клей, лак, линейка. Подготовка каркаса. Деревянным стержнем соединяют два фа нерных кружка (ри с. 77, б ) , причем больший фанерный кружок ставят на стержень на вы соте 210— 220 мм. П одготовленные 37 стоячков комельковым концом вставляют в малый фанерный кружок, а их тонкие концы пропускают через отверстия больш ого круга. Малый кружок как основа останется в изделии — на нем будет держаться абажур, поэтому стоячки надо вставлять плотно. Тонкими прутьями закрепляют стоячки у основания четырьмя рядами веревочки в три прутика, причем одна-две веревочки должны быть цветными. На высоте 80 мм оставляют прямой просвет и заплета ют три ряда веревочкой в три прутика (средняя — цветная). Расстояние между стоячками долж но бы ть одинаковым по всей окруж ности. Далее снова оставляют прямой просвет шириной 55— 60 мм. Запле тают две веревочки в три прутика, снимают больш ой фанерный кру жок и ставят 37 дополнительных цветных стоячков с левой стороны от основных. Затем выплетают цветную веревочку в три прутика и одну — белым материалом. Концы стоячков смачивают. Заверш ают плетение овальным бордю ром двойными прутиками высотой 70 мм. Работу ведут слева направо. После чего снимают большой фанерный круж ок и смачивают кончики стоячков. Плетение бордюра. Л ю бую пару прутиков сгибают дугой и пропу скают ее снаружи четырех соседних пар, заостренные концы прутьев вставляют слева к пятой паре стоячков. Таким образом загибают все остальные стоячки, проверяют линейкой высоту бордюра. После просушки концы прутиков, вставленные в бортик, промазывают клеем и покрывают изделие лаком. Затем закрепляют электропатрон с металлической трубкой в отвер стии малого кружка. Для плетения второй части потребуются: фанерный круг диамет ром 220 мм, с торцевой стороны которого просверливают 74 отверстия диаметром 5 мм для стоячков и одно отверстие в центре круга для шурупа; фанерный лист размером 7 0 0 Х 700 мм, на котором размечают 3 концентрические окруж ности диаметром 220, 380 и 580— 600 мм; 74 стоячка длиной 500 мм, диаметром 5 мм для каркаса; 74 цветных стоячка длиной 350— 400 мм, диаметром 4 мм для бордю ра; длинные цветные и белые прутья для веревочек. Подготовка к работе. Фанерный круж ок крепят шурупом к фа нерному листу. П одготовленные 74 стоячка вставляют в торцевые отверстия и оплетают четырьмя рядами веревочки в три прутика. О ставляют прямой просвет шириной 65— 70 мм. Диаметр изделия на этом этапе работы должен соответствовать диаметру второй окруж но сти на шаблоне (3 8 0 мм).
106
Плетение по шаблону. Заплетают стоячки веревочкой в три прутика и расставляют их так, чтобы расстояние между ними бы ло одинаковым. Затем делают ряд цветной веревочкой в два и один ряд белым материалом — в три прутика. Далее ставят дополнительные 74 цветных стоячка с левой стороны от основных (б е л ы х ). Заверш ают плетение бордю ром по третьей разметке на шаблоне. Б ордю р высотой 70— 80 мм выполняют парными прутиками слева направо. Л ю бую пару прутиков загибают дугой и обводят снаружи пять пар стоячков, заостренные концы вставляют в плетение слева к шестой паре стоячков. Таким образом загибают все остальные стоячки. Во время работы изделие постоянно долж но бы ть повернуто лицевой стороной вниз, поэтому прутья обрезаю т сверху. Д ля придания рассеивателю формы тарелки его кладут на большой таз так, чтобы края плетения опирались на бортики. На дно таза ставят какой-либо твердый предмет (например, кастрюлю, перевернутую дн ом ) и придавливают рассеиватель грузом так, чтобы его середина упиралась в подставку. Глубина прогиба плетения в центре должна бы ть 50— 60 мм. После просушки кончики стоячков, вставленные в веревочку, см азы ваю т'прозрачны м клеем и покрывают изделие лаком. Снимают фанерный круг, а концы стоячков обрезаю т заподлицо. Рассеиватель надевают на конусную часть абажура. Если он соскользнет ниже второго пояска конусной части, то мелкими прутиками, вставленными к основным стоячкам, выплетают в отверстии кромку до нужного диаметра.
Вазочка с двумя ручками (рис. 78) Размеры вазочки: высота — 80— 85 мм, диаметр донышка — 90— 95 мм, ширина верха — 170— 180 мм. Для плетения потребуются: 6 палочек длиной 120— 130 мм, диаметром 25— 30 мм, для крестовины З Х 3 и 3 дополнительные палочки; мелкий прутик для основания; 30 стоячков длиной 350— 400 мм, диаметром 2— 2,5 мм для каркаса; 60 прутиков длиной 280— 300 мм, диаметром 2,5— 2 мм для послойного плетения; тонкий прут для плетения веревочек; 30 прутиков для нижней кромки; 4 прута длиной 450— 500 мм, диаметром 250— 300 мм для ручек; две половинные ленты для крепления и одна цветная или белая для украшения ручек; два фанерных кружка диаметром 140 и 170 мм; деревянный стержень длиной 150 мм, диаметром 8— 10 мм для придания формы изделию; нож, бокорезы , шило, пилка, отвертка, шуруп, клей, лак. Подготовка к работе. Д ля каркаса берут упругие стоячки и заостряю т их на малый срез. В центре фанерных круж ков просверли вают отверстия. На деревянном стержне делают отметки на высоте 20 и 55 мм. 107
Р ис. 78. Вазочка двумя ручками
Основа. Д елают крестовину З Х 3 и ставят 3 дополнительные палочки (всего 15 кон цов). К рестовину шурупом крепят к стерж ню. В стержень на уровне первой отметки (2 0 мм) забивают 3— 4 малень ких гвоздика и надевают фанерный круж ок диаметром 140 мм. Затем на отметке 55 мм также забивают гвоздики и надевают на стержень второй кружок. С тоячки комельками вставляют в донышко (п о 2 к каждой палочке), поднимают их макушками вверх и связывают. У основания стоячки закрепляют веревочкой в три прутика. Плетение стенок. Работу ведут послойным плетением двумя прутиками, начиная с тонких концов. Закончив плетение, ставят направляющие палочки (п о две с каждой стор он ы ). Высота палочек должна соответствовать высоте стенок. Заостренные концы втыкают в плетеное донышко. Заверш ают плетение стенок веревочкой в три прутика, затем концы прутьев сильно увлажняют и выплетают кромку в три пары прутиков. В донышко вазочки вставляют короткие стоячки и закрепляют их веревочкой в два прутика, а затем делают кромку в три пары прутиков. Крепление ручек. И з стенок корзины вынимают направляющие палочки и на их место комельковыми концами вставляют четыре толсты х прута с застругом. На вы соте 2 00— 210 мм от донышка их соединяют между собой и закрепляют половинными лентами, подложив предварительно для украшения белую или цветную ленту. П осле сушки изделие покрывают двумя слоями лака.
Напольная ваза (рис. 79, а) Плетение больших ваз требует от исполнителя больш ого мастер ства, поскольку изделие долж но бы ть идеально правильной формы, а внешняя сторона работы очень чистой. Для придания необходимой формы используют простое приспо собление, сделанное из деревянного стержня с фанерными кружками. В плетении стенок вазы рекомендуется использовать цветной, белый (очищ енны й) и отварной материал. Размеры вазы: высота — 760 мм, диаметр осн ова н и я— 160— 170, диаметр сужения ножки — 80, высота основания — 60, диаметр в самом широком месте — 220, в горловине — 100, диаметр верха — 140 мм. Для плетения потребуются: фанерный круж ок диаметром 80 мм, толщиной 5 мм для основания; 23 стоячка длиной 8 50— 900 мм, диаметром 4— 4,5 мм для каркаса; 23 дополнительных стоячка длиной 350— 400 мм, диаметром 3— 3,5 мм; 46 белых прутиков'длиной 450 мм, диаметром 2,5 мм и 46 цветных прутиков длиной 500 мм, диаметром 3 мм для послойного плетения; мелкие цветные и белые прутья для стенок; длинные цветные и белые прутья для веревочек; круглая палка длиной 700 мм, диаметром 10— 12 мм для стержня; фанерные кружки109
шаблоны диаметром 100, 140 и 220 мм; болванка для основания (см . рис. 17, б ) ; нож, шило, бокорезы , лобзик, пилка, отвертка, 2 шурупа, клей, шпагат, 3— 4 маленьких гвоздика. Подготовка к работе. На плоскости и с торца фанерного кружка диаметром 80 мм просверливают по 23 отверстия диаметром соответственно 4— 4,5 и 2 мм, а также одно отверстие в центре для крепления основания к стержню. На деревянном стержне делают разметки на высоте 200 и 560 мм. О т верхней отметки стержень застругивают, чтобы получить здесь диаметр 8— 9 мм. В центре фанерного шаблона диаметром 220 мм просверливают отверстие диаметром 10— 12 мм, в шаблоне диаметром 140 мм — отверстие для шурупа, а в шаблоне диаметром 100 мм — отверстие в 8— 9 мм. На утолщенный конец стержня шурупом крепят ш аблон-основу; на первой отметке забивают 3— 4 гвоздика и надевают большой фанерный шаблон, а с-тонкого конца малый шаблон на вторую отметку и сверху прикручивают шурупом фанерный кружок диаметром 140 мм. В отверстия на плоскости ш аблона-основы плотно вставляют 23 стоячка для стенок вазы, оставляя внизу комельки длиной 120— 130 мм, макушки стоячков поднимают вверх и связывают. Плетение стенок. Цветным материалом выплетают веревочки в два прутика на вы соту 50 мм. Закрепив работу веревочкой в три прутика, оставляют продольный просвет шириной 40 мм и еще раз оплетают веревочкой в три прутика. Затем выполняют послойное плетение парными белыми прутиками, начиная с тонких концов, и проплетают их на всю длину. Д елают три ряда (п о краям цветные, в середине белы е) веревочкой в три пру тика. Большой фанерный шаблон снимают и продолж ают послойное плетение цветным материалом парными прутиками, начиная с толсты х концов. Закрепляют плетение тремя рядами веревочки в три прути ка — по краям белым материалом, средний ряд — цветным. С левой стороны от основных ставят дополнительные стоячки и выплетают ажур крестиком на вы соту 60 мм (см . рис. 79, б ) . Затем любой дополнительный стоячок загибают влево под соседний и соединяют с соседним — основным на высоте 60 мм от места сгиба. Таким образом загибают дополнительные и основные стоячки. Полученные пары стоячков закрепляют веревочкой в два пру тика белым материалом. После чего выплетают цветным материа лом одну веревочку в два и одну веревочку в три прутика и выполняют 10 рядов простого плетения белым материалом. Заверш ают работу веревочкой в три прутика. Оставляют прямой просвет парными прутиками на высоту 30 мм и цветным материалом делают одну веревочку в три прутика. П родолж ают плести простым плетением до горловины вазы. Затем в каждой паре обрезаю т по одному стоячку. Горловину вазы выполняют простым плетением, при этом диаметр ее должен постепенно увеличиваться до верхнего шаблона. Затем ставят 110
Рис. 79. Напольная ваза:
дополнительные короткие стоячки и заканчивают плетение кромкой в четыре пары прутиков. Деревянный стержень вынимают и снизу крепят малую болванку. Увлажняют комельки стоячков и делают 10 рядов веревочкой в два прутика белым-материалом, оставляют прямой просвет шириной 25 мм и заканчивают плетение цветными прутиками. О брезаю т бокорезами кончики комельков, проверяют ровность плетения. К каждому стоячку подставляют два дополнительных (белы й и цветной) и плетут кромку в четыре прутика. В торцевые отверстия фанерного донышка вставляют тонкие стоячки и выплетают кромку в три или четыре пары прутиков. После завершения работы концы прутьев обрезаю т, сушат вазу и покры вают лаком. Изменяя размеры фанерных круж ков и их расположение на стержне, можно выполнять изделия самой разнообразной формы.
ПЛЕТЕНИЕ БЕРЕСТЫ
История плетения бересты гМзделия из бересты извест ны с давних времен. Поделка таких изделий считается одним из са мых древних ремесел и является исконно русским промыслом. Береста — наружная часть коры березы, состоящ ая из легко отделяемых друг от друга тонких, полупрозрачных, гладких, бе лых, желтоватых и красноватых слоев. Береста обладает рядом свойств, позволяющ их найти этому материалу самое широкое применение: пластичностью, малым удель ным весом, бактерицидностью, гигроскопичностью, гидро- и термоизоляционностью, а главное — доступн остью и простотой обработки. Бересту использовали в строительстве для защиты от холода, гнилей и сы рости. Берестой обшивали лодки, делали из нее поплавки и другие рыбацкие принадлежности. И з бересты изготавливали обувь, посуду, чемоданы, игрушки, кузова, украшения и многое другое. И з сухой перегонной бересты до сих пор добы ваю т деготь. Берестяные грамоты, дошедшие до нас, являются древнейшими памятниками славянской культуры. И скусство художественной обработки бересты достигло вы сокого уровня в Восточной и Западной Сибири, на Дальнем Востоке, а также на русском Севере и в Российском Черноземье. У каждого народа сложились самобытные традиции плетения и способы художественного оформления берестяных изделий — тиснение, роспись, резьба, выскабливание и т. д. 113
Одним из древнейших способов украшения берестяных изделий является тиснение. К рупные центры по тиснению имелись во многих районах России — на Среднем Урале, русском Севере и др. Тиснение по бересте делали специальными кренеми (своего рода штампиками) или чеканами. Наибольшее распространение получили рисунки с изображениями различных птиц, зверей, орнаменты с растительными мотивами, а также простейшие геометрические фигуры: полоски, звездочки, круги и др. Ш тампики (чекан ы ) делали из твердых пород дерева (дуба, вяза, бер езы ), а также из металла, пустотелых трубочек и кости. На торцевой стороне деревянных брусков или круглой палочки вырезали какой-нибудь элемент орнамента, прикладывали его к бере сте и, ударяя по штампу молотком, наносили рисунок. Роспись по бересте — один из самых интересных и распростра ненных видов народного творчества. Во многих районах традиционно сложились различные приемы росписи. В основном расписывали поверхность туесков (стенки и крыш ки). Среди расписных берестяных изделий выделяются работы мастеров Западной Сибири, Урала и русского Севера, Пермогорья (на Северной Д вине) — так называемая пермогорская роспись туесков. Многие мастера русского Севера для украшения изделий широко использовали резьбу. В этой технике выполняли как несложные геометрические и растительные орнаменты, так и целые сюжетные композиции из жизни людей, птиц, зверей, при этом часто применяли цветные подкладки из фольги или ярко окрашенной бумаги, а также бересты разных оттенков. Большое развитие получил и такой вид отделки, как прорезная береста, особенно в селенье Ш амогодье в окрестностях Великого Устюга. Исследователи северных народных ремесел считают, что шемогодская прорезная береста возникла в X V II или начале X V III в., а позже формируется как искусство ажурного орнамента. Раститель ным резным орнаментом украшали боковы е поверхности туесков, крышки и стенки шкатулок и ларцов. Ш емогодское мастерство получило больш ую известность не только в нашей стране, но и за рубежом. В 1882 г. изделия из прорезной бересты шемогодского масте ра И. А . Вепрева получили больш ую золотую медаль на Всероссийской выставке в М оскве. А в начале X X в. берестяные изделия мастеров России на Всемирной выставке во Франции были удостоены диплома. В настоящее время на Великоустюгской фабрике художественных изделий (г. Великий У стю г) продолжается выпуск продукции с шемогодской прорезной берестой (шкатулки, кружки, туески, зеркальные рамы и т. п .). Одна из старейших мастериц и инициатор производства берестяных шкатулок А . Г. М аркова со своими ученика ми продолжает лучшие традиции шемогодских мастеров, разрабатыва ет новые современные темы в резьбе. Еще один продолжатель традиций мастеров Севера участник Великой Отечественной войны В. А . К осты лев занялся плетением из 114
бересты в 65 лет. Когда врачи категорически запретили ему работать преподавателем, неожиданно пришло решение обратиться к редкому жанру народного творчества — созданию скульптур и композиций из бересты. Уж е через несколько лет состоялась первая выставка, на которой особы м успехом пользовались его композиции: «З а власть советов», «В атаку!», «Н а привале», «Т ревога», «В ои н» и др. « О ткры в в себе новое призвание, К осты лев продолжает создавать удивительные работы, воплотившие героев карело-финского эпоса «Калевала». Вскоре сюжетное плетение умельца было представлено на городской и республиканской выставках, отмечено серебряной медалью В Д Н Х . Е го изделия с успехом демонстрируются на выставках в Венгрии, Англии, Финляндии, Ш веции и Ф Р Г . Берестяные герои мастера стали экспонатами музеев М осквы , Ленинграда, П етрозавод ска, Суздаля. С ою з художников Р С Ф С Р присвоил В. А . К осты леву звание народного мастера. П родолж ая лучшие традиции народного творчества, современные мастера в своих работах ищут новые темы и разнообразные решения. Например, мастерицу из К остром ы В. Е. Ш антыреву привлекают персонажи русских народных сказок. О собое место в творчестве Ш антыревой занимают декоративные вазы, детские погремушки, всевозмож ные берестяные ларцы, салфетки, корзинки, походные солонки, исполненные в лучших традициях народного творчества. Совершенствуя технику плетения, она постоянно ищет наиболее вы разительную форму, работает над украшением изделий. В. Е. Шантырева участвовала в московской выставке «Береста Р оссии», где были представлены ее собственные изделия и работы ее учеников. В костромском музее народной архитектуры и быта экспонируются коробочки, сундучки, вазочки, детские погремушки, скульптуры и т. д., которые В. Е. Ш антырева подарила музею. Рассказ о талантливых народных мастерах может бы ть беско нечным. Ряды продолжателей традиций старинного искусства посто янно расширяются, но главное в творчестве этих преданных своему делу людей то, что они охотно делятся опытом и секретами своего мастерства с учениками, приобщая их к миру прекрасного, даря людям радость и вдохновение.
Заготовка бересты Бересту заготавливают в разные сроки в зависимости от климатиче ской зоны, в средней полосе в мае — июне, но предварительно надо получить разрешение лесного хозяйства или лесничего. Заготовка бересты — занятие трудоемкое, требующ ее большой физической нагрузки, т. к. нередко приходится делать большие пешие переходы. Собираясь в дорогу, надо взять с собой нож, шпагат или тонкую проволоку, рюкзак. Лучше брать бересту на вырубке леса, например, где прокладывают дорогу. С о спиленного или срубленного дерева можно легко снять 115
бересту не только с нижней, но и с верхней части ствола. На большой вырубке материал запасают на многие годы. Береста должна бы ть гладкой, ровной, без болезненных утолщений и наплывов. Л учш ую бересту — плотную, слоистую и эластичную получают с берез, произрастающ их в смешанном лесу. Совсем не годится материал, взятый в болотисты х местах. Белоснежная береста снимается легко, надо только слегка надре зать ствол сверху вниз, не делая горизонтального разреза. Ш ирина пласта должна бы ть 35— 40 см, а длина — в соответствии с диаметром дерева. Д ерево выбирают в зависимости от назначения бересты. Д ля мелких изделий требуется тонкий, мягкий материал. Е го берут от более молодых берез небольшого диаметра. В любом случае возраст дерева должен бы ть не менее 15 лет. Нарезав бересту пластами, ее держат в тени. Когда береста начнет закручиваться, ее скатывают в рулоны, наматывая последовательно пласты светлой стороной наружу (ри с. 8 0 ). Причем следует совмещать концы, прижимая верхним слоем нижний, чтобы при высыхании они не закручивались. Смотав в рулон 8 — 10 пластов (количество зависит от их длины ), его заворачивают в бумагу и завязывают шпагатом или проволокой. Д ля изготовления туесков-бураков, в которы х можно хранить жидкие или скоропортящ иеся продукты, нужна бесшовная внутренняя часть, которую целиком снимают с дерева. Н азы ваю т ее по-разному — дуплё, сколотень или берестяный цилиндр. Такую цельную бесшовную бересту снимают только со спиленных деревьев. Заготовка материала для туесков-бураков представляет особую трудность. Не всякая береза годится для снятия сколотней. Н уж но выбрать ствол с чистой и гладкой поверхностью, без болезненных наплывов и трещин. Для снятия сколотня годится только спиленное дерево. Сначала удаляют участки с сучьями, на ровных частях делают кольцевые надрезы и при помощи тонкого клина-щупа или толстой стальной проволоки понемногу отделяют бересту. Затем ее сдергивают и получают цельный цилиндрический сколотень. Сколотни начинают снимать поочередно с тонкого конца ствола. Снятые сколотни также протирают тряпкой. Заготовка бересты с погибших деревьев. В лесу часто можно встретить упавшие березы, у которых сгнила древесина, а береста осталась целой, или сухостойные березы, поврежденные грибомтрутовиком. У таких деревьев береста отделяется легко в любое время года. Внутренний слой ее окрашен в красно-коричневый цвет различного оттенка, он используется для украшения изделий. Техника безопасности. Н аходясь в лесу, надо бы ть предельно внимательным. Н ельзя появляться на делянке во время вырубки леса — это опасно. П ользоваться ножом следует умело и осторож но. Коллективный вы езд на заготовку бересты проводят только под руководством педагога, при этом надо иметь аптечку для оказания первой доврачебной помощи. 116
Обработка бересты Для работы готовят тупой и остры й ножи, ножницы, сухую тряпку и подсолнечное масло. Бересту раскладывают на столе, лучше на свежем воздухе в тени; здесь она и сушится. Н е следует разворачивать рулон полностью. Сначала берут один пласт, протирают его сухой тряпкой и кладут на стол вверх белой стороной. Бересту нужно разделить на несколько слоев; сначала отделяют верхний шероховатый белый слой. Отделяемый от бересты верхний пласт может бы ть один-, двухслойным, его следует сохранять для украшений, обмотки ручек, ободков, оправ, а также для придания ж есткости туескам и вазам. Пласты снимают при помощи тупого ножа с овальным концом или руками. Если береста тонкая, снятая с молодых деревьев или с верхней части ствола, ее не делят на пласты, а оставляют полностью. Т ак ую бересту можно заплетать с обеих сторон — с белой и темной (изнаночн ой). Все утолщения и наплывы, а также места, где были сучки, вырезают ножом или ножницами. О бработанную бересту сушат в тени отдельными пластами. При этом следят, чтобы она не пересохла, иначе материал станет жестким и хрупким. Работать с такой берестой невозможно. Когда берестяные пласты начнут скручиваться, их собираю т в рулоны, предварительно протерев тряпочкой, смоченной в подсолнеч ном масле. О стается рассортировать бересту по цвету, завернуть в бумагу и указать на ней, какого цвета береста и дату ее заготовки. О бработанную бересту можно также спрессовать, укладывая ее в помещении пластами на ровную поверхность внутренней (тем н ой ) стороной вниз. Сверху ее прижимают доской, которая должна полностью закрывать кладку, и ставят груз, чтобы пласты не сворачивались. При правильной сборке бересты в рулоны и прессовке можно сохранить много качественного материала.
Хранение бересты В прохладном затемненном помещении или в кладовке при комнатной температуре бересту можно хранить годами. В сы ром помещении береста покрывается плесенью, пятнами. Плохо высушенный материал тоже не может долго храниться. Ч тобы береста не потеряла мягкость, эластичность и натуральный цвет, следует периодически проверять, не пересохла ли или не отсырела она. Обнаруж ив на бересте пятна сы рости, необходимо тщательно проветрить помещение, после чего просуш ить ее и с изнаночной (тем ной ) стороны протереть тряпочкой, смоченной подсолнечным Маслом. 117
Рис. 80. Сборка бересты в рулоны
Рис. 82. Коточик
П ересохш ую бересту можно отмочить в теплой воде или подержать над паром. После чего проводят все операции, как и при заготовке с дерева,— сушку, сворачивание в рулоны. Рулоны можно укладывать на полки в кладовке, а спрессованные пласты — на пол под гнет. Сколотни хранят вставленными один в другой.
Организация рабочего места Рабочее место для плетения из бересты организуют так же, как при работе с ивовым прутом. В помещении должны бы ть естественное и электрическое освещение, водопровод, кладовая для хранения материала, низкий стол и стул. В учебном классе столы размещаются с таким расчетом, чтобы работающие не мешали друг другу. Если нет возмож ности обеспечить всех специальной мебелью, можно пользо ваться обычными столами и стульями. Техника безопасности и противопожарная профилактика. Н адо помнить, что береста — быстровоспламеняющ ийся материал, поэтому пользоваться открытым огнем вблизи мест ее хранения запрещается. Основны е причины пожара — курение в неустановленном месте, применение откры того огня в помещении, нарушение правил эксплуа тации электроприборов, в том числе работа неисправных приборов. При работе с синтетическим клеем надо соблю дать особую осторож ность: хранить и пользоваться им вдали от источников откры того огня, в хорош о проветриваемом помещении, учебные классы должны бы ть оборудованы приточно-вытяжной вентиляцией. Рабочее место необходимо содерж ать в чистоте. После окончания занятий обрезки бересты выносят в специально отведенное место. Учебные классы, мастерские и рабочие места должны быть оборудованы в соответствии с требованиями санитарии, гигиены и техники безопасности. На рабочем столе отводят место для инструмента, а лучше складывать его в специальный ящик. Беспорядок на столе, р азбро санные инструменты могут стать причиной травмы. К оточик, шило, ножи, ленторез должны быть с гладкой овальной ручкой, выполненной из древесины твердых пород. При заточке ножей надо соблю дать особую осторож ность.
Инструменты и приспособления Больш инство инструментов и приспособлений, необходимых для заготовки и плетения бересты, имеется в каждом доме: нож (ри с. 81) и ножницы, кусачки и плоскогубцы, канцелярские скрепки, цир куль, линейка, шило. Часть инструментов и приспособлений при дется сделать самим: ленторез, коточик, шаблоны, гладкую дере вянную дощ ечку и др. 119
Рис. 83. Ленторез: а — нарезка лент; б — устройство лентореза
Рис. 84. Шаблон для портсигара
Рис. 85. Шаблон для футляра для очков
Р ис. 86. Шаблоны для короба: а — рамка для корпуса; б — оправа для крышки
Рис. 87. Расклини вающий шаблон
Нож острый служит при заготовке и обработке пластовой бересты. Нож с тупым овальным концом необходим для отделения от бересты верхнего слоя. Нож-косяк с длинной рукояткой и острым коротким лезвием служит для резьб,ы по бересте. Ножницы среднего размера нужны при обработке бересты, заготовке ленточек и плетении изделий. Шило слегка притупленное и отшлифованное необходимо для выполнения рисунков на бересте. Коточик — металлический выгнутый стержень с плоской поверхно стью имеет удобную деревянную ручку (ри с. 8 2 ). Ручку лучше выполнять из древесины твердых пород. При помощи этого самодель ного инструмента проделывают проходы между ленточками во время плетения. Ленторез служ ит для приготовления берестяных лент-лычек разной ширины (ри с. 8 3 ). Э то приспособление состоит из двух деревянных пластин и металлического лезвия. Длина пластин — 150 мм, ш ирина— 60, толщина одной из них — постоянной — 15 мм, второй — съемной — зависит от вида работы. Лучше заранее заготовить несколько съемных пластин толщиной 6, 8, 10, 12, 15 и 17 мм. Рекомендуемая ширина съемных пластин соответствует самым распространенным в плетении размерам ленточек. Лезвие (н ож -к ося к ) лентореза делают из ножовочного полотна с односторонней заточкой. На ноже долж но бы ть отверстие для крепления к деревянной пластине. На постоянной пластине делают паз и закрепляют нож-косяк так, чтобы носик его выступал на 3 мм ниже пластины. Если к постоянной пластине прикрепить съемную шириной 12 мм, шурупами можно нарезать берестяные ленточки такой же ширины (ширина ленточек измеряется толщиной съемной пластины, считая от н ож а). Так, заменяя пластины, получают ленточки разной ширины. М ож но сделать несколько ленторезов, установив на каждом из них лезвия для нарезки лент определенной ширины*, чтобы не приходи лось каждый раз менять пластины. На каждом ленторезе указывают толщину пластины. Сосновая доска (см . рис. 83, а) длиной 1100— 1200 мм, толщи ной — 20, шириной 100 мм нужна при работе ленторезом. По середине доски прибивают деревянную рейку длиной 1100— 1200 мм, шириной — 25— 30, толщиной 10— 15 мм. Бересту кладут вдоль рейки и вы резают ленты нужной ширины, упирая съемную плас тину лентореза в рейку. Канцелярские скрепки и зажимы при работе не дают расплетаться лентам. Зажимы типа «крокодил» длиной 45 мм можно приобрести в магазинах «К ул ьттовары ». Шаблон — готовый образец, по которому изготавливают изделие. Очень важно выполнить шаблоны, ободки и оправы точно по указан ным размерам, соответствую щ им количеству и ширине ленточек. Если в размерах будут отклонения, изделие может получиться неправиль 122
ной формы, потеряет устойчивость и привлекательность. П оэтом у надо помнить, что качество плетеных изделий зависит от того, насколько тщательно изготовлены шаблоны. При работе могут понадобиться, например, шаблоны — деревянный для портсигара (ри с. 8 4 ), футляра для очков (ри с. 8 5 ) и др. Рамка (ри с. 86, а) требуется для изготовления прямоугольных изделий, коробов. Длину и ширину определяют исходя из размеров изделия. Рамку делают из досок толщиной 15— 20 мм. Оправа деревянная для крышки короба из доски толщиной 35— 40 мм (р и с. 86, б ) . При больших размерах оправы соответственно увеличиваются количество и ширина лент. Разборная форма-шаблон может потребоваться для некоторых плетеных изделий. Такие шаблоны могут быть самой разной формы, например, расклинивающий круглый шаблон (ри с. 8 7 ) для придания выпуклой формы берестяным изделиям. Д елают его из дерева. Для чего от чурбака отпиливают круглую болванку диаметром 170 мм и высотой 55 мм, закругляют ее края с обеих сторон, чтобы диаметр верхней и нижней плоскости составлял 90 мм, и просверливают отверстие диаметром 40 мм. Затем делают круглую распорку диаметром 40— 45 мм. Ф орму-ш аблон распиливают на 4 части. При работе вставляют распорку в отверстие шаблона. Проволока нужна для изготовления ручек, ободков и оправ для хлебниц, конфетниц, цветочнии и др. Клей типа «М ом ен т», «М а р с», «С уперцемент» и др. может потребоваться для крепления лент, при обработке ручек и ободков, а также при изготовлении туесков. Тонкая жесть используется при изготовлении оправы для верхней части шкатулок, цветочниц, коробов. Гвозди необходимы для разметки на доске или чурбаке нужной формы — круглой, прямоугольной, овальной. Нитки нужны для крепления верхней части некоторых мелких изделий.
Подготовка бересты к плетению П режде чем приступить к плетению того или иного изделия, необходимо определить его назначение и форму. Ж елательно сделать рисунок, чтобы рассчитать размеры и потребное количество лент. Красота изделия зависит от правильного подбора толщины и цвета бересты. Н уж ны й цвет выбирают по целому куску бересты, т. к. по тонкой ленточке трудно определить цвет будущ его изделия. Правильная форма, плотность и устойчивость изделия зависят исключительно от точности нарезки лент. Если одна из 10 лент будет шире или уже остальных, изделие потеряет устойчивость и форму. 123
Приступая к изготовлению изделий, необходимо особенно тщатель но подготовить материал, качественно его обработать, правильно и умело использовать. Например, если для маленькой вазочки или солонки требую тся ленты длиной 400 мм, то не следует брать более длинные, иначе в обрезки уйдет много качественного материала.
Нарезка берестяных лент Рулоны бересты раскручивают и выгибают в обратном направле нии. На стол или верстак кладут доску с рейкой, чтобы с одного ее конца был упор. Бересту протирают тряпочкой, смоченной в подсол нечном масле, ровно обрезаю т ленторезом одну сторону и укладывают изнаночной стороной вверх так, чтобы она плотно прикасалась к рейке на доске. Придерживая левой рукой, прижимают берестяной пласт плотно к рейке, правой рукой ленторезом отрезаю т ленту. Следят, чтобы нож на доске проходил по одному месту, тогда ленты будут одинаковой ширины. Ш ирину ленточек тщательно выверяют, а затем ножницами заостряют с обеих сторон (ри с. 8 8 ). Для плетения конкретного изделия не следует заготавливать лишние ленты — они вы сохнут и будут непригодны к работе.
Плетение полотна Ч тобы освоить плетение бересты, надо сделать немалое количество изделий. Значит, времени и труда придется затратить много. Д ля отработки приемов и способов плетения не потребуется специальный тренажер, как при работе с ивовым прутом. Узнать секреты мастер ства можно только регулярно выплетая изделия. Для работы с берестой так же, как с ивовым прутом, потребуется основание, на котором выплетают изделие. В поделках из ивового прута таким основанием могут бы ть плетеное донышко, каркас, обруч, фанерный диск и т. д. Д ля берестяных работ основанием является полотно из лент. П олотно выплетают рядами клеток (квадратиков), расположенных строго по горизонтали и вертикали. Количество ленточек, их ширина и длина могут быть различны в зависимости от того, какое делается изделие. С ущ ествует такой сп особ обозначения размеров полотна-основания: З Х 3, 4 Х 4, 5х 5, 6 Х 6, 7х 7, 8х 8, 10х 10 ленточек и т. д. Если указано «полотно 8 X 8 » , это значит, что надо заготовить 16 ленточек, т. е. по горизонтали и вертикали основания заплетают по 8 лент. В работе с берестой используют преимущественно один вид плетения — клетчатый узор, сходный с рисунком шахматной доски. В зависимости от расположения клетки узора могут бы ть прямыми и наклонными (р ом би к ом ), но в любом случае они должны бы ть строго одного размера.
124
Рис. 88. Ленточки с заостренными концами
Рис. 89. Подготов ка полотна: а — раскладка лент; б — готовое полотно; в — разметка донышка; 1 , 3 — горизонтальные точки; 2, 4 — вертикальные точки
Большинство изделий выплетают в два слоя, что повышает их прочность. О бы чно при плетении изнаночная сторона бересты становится лицевой на изделии. Изнаночная сторона бересты бывает бледножелтой, желтой, коричневой с красноватым оттенком, темно-желтой, пятнистой с выпуклыми «иголками» и т. д. Такое разнообразие цветов и оттенков дает возмож ность делать изделия из бересты красочными и нарядными. Очень красиво выглядит изделие, выполненное комбинированным плетением белыми, коричневыми, светло-желтыми, темно-коричне выми и другими лентами. Береста, имеющая двусторонню ю окраску, используется для однослойного плетения. Изделия получаются легкие, красочные и более изящные. Внешнюю сторону бересты (бел ую или бел о-розовую ) можно использовать для отделки, выплетая цветы, звездочки, пояса и д ор ож ки, квадраты и угольники. Для полотна 8 Х 8 потребуются: 16 берестяных лент шириной 12 мм, длиной 200— 250 мм, концы каждой ленты заостряю т; нож, коточик, ножницы, ленторез шириной 12 мм, доска с рейкой, зажимы, линейка. Плетение. Две ленточки перегибают пополам и определяют у них середину. К ладут их на стол крест-накрест, чтобы внутренняя темная сторона была лицевой. С ледую щ ую пару ленточек заплетают, выравнивая концы с первой парой. Ленты укладывают так, как показано на рисунке 89, а. Расстояние между парами равняют по линейке. Уплотняют ленточки большим, указательным и средним пальцами. Применять инструменты при уплотнении не рекомендуется, т. к. можно повредить ленты. Заплетают еще по одной ленте со всех четырех сторон. Ленты уплотняют (каж дую отдельн о), проверяют расстояние между ними. Плотность полотна определяют там, где соприкасаются две горизонтальные и две вертикальные ленточки. З д есь всегда бывают небольшие отверстия. Если береста толстая, бархатистая — отверстия больше; тонкая — меньше, но в любом случае они должны бы ть одинаковыми. Э то достигается аккуратностью раскладки лент и посто янным уплотнением их при плетении полотна. Таким образом заплетают все 16 ленточек. Каждый из четырех углов плотно закрепляют зажимами (рис. 89, б ) . Расстояние между лентами долж но бы ть одинаковым. О со б у ю точность следует собл ю дать между горизонтальными и вертикальными точками. Завершив плетение полотна, необходимо определить углы донышка будущ его изделия. Углы находятся на стыке четвертой и пятой ленточек с каждой стороны полотна (ри с. 89, в ). Расстояние между углами по диагонали долж но бы ть абсолюно точным. Теперь можно приступать к плетению стенок изделия. В данном случае они будут в наклонную клетку.
Изготовление ободков и ручек Д ля придания прочности и сохранения формы верхней части изделия применяют ободки из проволоки, лучше всего алюминиевой диаметром 1— 3,5 мм. Для изготовления круглого ободка циркулем чертят на доске или чурбаке окруж ности диаметром 100, 115, 150, 215 мм. П о кругу забивают мелкие (3 0 мм) гвозди и загибают по ним проволоку (рис. 90, а). Концы ободков закрепляют холодной пайкой. Затем вы резают из жести тонкую пластинку длиной 30— 40 мм и шириной 20— 25 мм, огибают ею концы обода и плотно обж имают плоскогубцами. При этом следят, чтобы концы ободка упирались друг в друга. На концах пластинки кусачками делают по две зарубки и лишнюю ж есть обрезаю т (ри с. 90, б ) . Таким сп особом делают круглые ободки разных размеров. Для изготовления ободков диаметром 100 и 115 мм требуется около 400 мм проволоки, диаметром 150 мм — соответственно 500 мм. Ободок овальной или прямоугольной формы использую т при плетении вазочек, корзинок для конфет и фруктов. На доске вычерчивают контур ободка длиной 210 мм и шириной 140 мм, по периметру забивают гвоздики (ри с. 9 1 ). Затем проволоку длиной 700 мм, диаметром 3— 3,5 мм загибают вокруг гвоздиков. Стык может быть на длинной или короткой стороне, в зависимости от того, где будут ручки. Концы спаивают. Затем ободок кладут на ровную поверхность и выравнивают. О своив заготовку ободков, надо научиться крепить к ним ручки. В практике применяют разнообразные способы соединения и креп ления ручек к изделию. Например, ручки сначала прикрепляют к ободку, обматывают берестяными лентами и заплетают в изделие. Для чего на круглом ободке диаметром 115 мм сначала на противополож ных сторонах размечают место крепления ручек. Расстояние между ними — 30 мм. Д ля каждой дужки потребуется проволока длиной 320 мм и с припуском 30— 40 мм. П рипуски затачивают с одной стороны напильником, чтобы при крепленкги к ободку не сломались концы. Выгибают проволоку дугой, заточенными концами внутрь, кругло губцами прикрепляют дуж ку к ободку. В торую дуж ку выравнивают по первой, чтобы вверху они соединились над центром ободка (ри с. 9 2 ). Высота ручек от ободка — 100 мм. На ободке с закругленными углами прикрепляют три ручки: поперечные — короткие или продольные — длинные (ри с. 9 3 ). С о ответственно заготавливают проволоку необходимой длины. Если ручки продольные, пайка на ободке должна бы ть на длин ной стороне, если поперечные — на короткой. На противополож ных сторонах ободка определяют середину 127
Рис. 90. Изготов ление круглого ободка: а — шаблон для укладки проволоки; б — крепление ободка жестью
Р ис. 91. Изготовле ние овального ободка
Рис. 92. Круглый ободок с двумя ручками
Рис. 93. Прямоу гольный ободок: а — с тремя продольными ручками; б — с тремя поперечными ручками
и закрепляют здесь средню ю дужку, а слева и справа от нее на расстоянии 25— 30 мм устанавливают две другие, выравнивая их по центральной. Длина продольных дужек — 460— 470 мм, поперечных — 370— 380, с учетом п ри п уск а — 15— 20 мм. Высота готовых продольных ручек от о б о д к а — 130 мм, поперечн ы х— 120 мм. Выплетая маленькие изделия из тонкой бересты без ручек, закрепляющий ободок можно делать из тонкой проволоки. При этом концы ободка не запаивают, а связы вают ниткой. М ож но делать оправу и из жести, но ее крепят непосредственно на изделие во время плетения.
Отделка ручек и ободков Д ля работы потребуются: ленточки из бересты для оплетки ручек шириной 6 — 8 мм из самой тонкой бересты одного цвета с внутренней отделкой изделия; ленточки для оплетки ободков шириной 15— 20 мм; ленточка шириной 6 мм, длиной 90— 100 мм белого цвета; нож, ножни цы, ленторез и клей. Оплетка ручек. П окрывают клеем дуж ку и ленточку. Затем, начиная от ободка, оплетают дуж ку по спирали, желательно, чтобы одной ленты хватило на всю ручку. Оплетку ободков можно выполнять так же, как оплетку ручек, но чаще применяют другой способ. Т он к ую берестяную ленточку, по длине равную длине ободка, покрывают клеем и накладывают сверху на ободок. Внизу края ленты соединяют и после высыхания срезаю т (ри с. 9 4 ). Работу следует выполнять аккуратно, чтобы металлическая поверхность ручек и ободков была полностью закрыта. После завершения плетения изделий с двумя и тремя ручками необходимо соединить и закрепить их вверху. Для этого ручки обматывают берестяными ленточками. Закрепление ручек. Сначала покрывают клеем поверхность ручек и ленточек. Затем соединяют ручки вверху, выравнивают их по центру и для украшения накладывают сверху вдоль дуги белую ленточку. Затем один конец темной обмоточной ленты покрывают клеем, зажимают его между дужками и делают один виток обмоткой вокруг ручки, придерживая конец белой ленты (ри с. 9 5 ). Следующ ий виток проходит под белой ленточкой, затем по ней и т. д. Таким образом заплетают ручки на 65— 70 мм. К онец обмоточной ленточки покрывают клеем и заправляют между дужками. После просушки концы обрезаю т.
Плетение изделий из полотна Маленькая круглая вазочка (рис. 96, а) Для работы потребуются: 16 ленточек шириной 12 мм, длиной 350— 400 мм для плетения полотна; ободок диаметром 100 мм, оклеенный берестяными ленточками; коточик, ножницы, ленторез, доска с рейкой, линейка, 8 прищепок. Для плетения полотна 8 Х 8 две ленточки кладут на стол крест-на крест (п о центру) внутренней стороной вверх. Переплетают другой парой. П роверяю т расстояние между ними, с каждой стороны приплетают еще по одной ленте. Далее, подтягивая ленты и уплотняя плетение, заплетают остальные ленты. Готовое полотно закрепляют на углах зажимами. Затем определяют углы квадратного донышка будущ его изделия. Они находятся на стыке 4-й и 5-й ленточек с каждой стороны полотна. Расстояние между углами долж но бы ть 75 мм, или четыре клетки с каждой стороны . Тупы м шилом или коточиком на полотне намечают квадрат, соединив все точки донышка, особенно четко выделяют линии на углах. Если длина сторон не совпадает, с одного конца полотна снимают зажимы, уплотняют и снова закрепляют ленты. Плетение стенок. Высота вазочки соответствует высоте четырех клеток (6 5 м м ), но сразу выплетать стенки целиком не следует. Сначала концы лент на одном из углов поднимают вверх, заплетают, чтобы получились 2 клетки (ри с. 96, б ) , и закрепляют прищепкой. Плетение идет не по кругу, а как указано на рисунке 96, в, сначала выплетают угол / , затем 2, 3 и 4. Каж дый угол аккуратно уплотняют, чтобы не бы ло слабины и перетяжек. Затем начинают опять с угла / в той же последовательности и плетут стенки на высоту 4 клеток. Закончив плетение, надевают ободок на высоте 4-й клетки, придавая таким образом нужную форму изделию. Внизу получилось квадратное донышко, образующ ее опору вазочки. Затем выплетают второй слой изделия, перегибая попарно ленточки. Загибка лент черев ободок — одна из трудных и важных операций при плетении. С ущ ествую т три способа загибки — прямая и одиночны ми и двойными зубцами. Д ля п р я м о й з а г и б к и ленточки делят на пары и перекрещива ют между собой. О бод ок при этом должен находиться на одинаковой высоте от всех четырех углов. Работу начинают с лю бого угла. Пару ленточек перегибают через ободок так, чтобы они плотно облегали его. При этом коточиком немного приподнимают ближайшую поперечную ленту, в образовавш ийся проход вводят заостренный конец левой 131
Рис. 94. Ободок, оклеенный целой
Р ис. 95. Соедине ние ручек
г — прямая загибка; 1 — правая ленточка; 2 — левая ленточка (цифрами и стрелками показан порядок выполнения операций)
ленточки и протягивают ее в правом направлении (ри с. 96, г). Таким же образом проводят правую ленту в левом направлении. Ленточки второго слоя должны быть наружу своей темной (изнаночной) стороной. Затем двумя ленточками формируют противоположный угол, также заправляя их под поперечную. Заплетают остальные углы и, убедившись, что ободок закреплен ровно, перегибают попарно остальные ленты таким же способом. Плетение второго слоя значительно проще, каждая ленточка имеет свою дорож ку, таким образом ее протаскивают при помощи коточика под всеми поперечными лентами и заканчивают плетение наружного (в т о р о г о ) слоя. О бр езаю т оставшиеся концы ножницами или ножом с овальным носиком. Если ленточка оборвалась или оказалась короткой, ее можно нарастить, используя дополнительную такого же цвета. Для чего коточиком приподнимают поперечную ленту в месте обрыва и вводят в просвет новую ленту. Ф орма вазочки не должна быть цилиндрической: ее стенки выпуклые, диагональ донышка немного больше диаметра верхнего ободка. Если готовое изделие неустойчиво, значит, при работе допущена ошибка: не выдержана одинаковая ширина ленточек при нарезке или не точно сформирован квадрат донышка (расстояние между углами неодинаковое). Исправить подобные недостатки готового изделия уже невозможно. П оэтом у в процессе плетения надо уметь находить и устранять свои ошибки. Для защиты плетеных изделий из бересты от воздействия повышенной влажности, колебаний температуры воздуха и загрязнения рекомендуется протирать темную (изнаночн ую ) сторону бересты тряпочкой, смоченной в подсолнечном масле. О т этого проявляется активнее натуральный цвет изделия, улучшаются эксплуатационные и декоративные качества.
Конфетница с одиночными зубцами (рис, 97, а) Для плетения потребуются: 16 ленточек шириной 12 мм, длиной 400— 450 мм для полотна; цветная ленточка шириной 12 мм произвольной длины для пояска на стенке изделия; ободок диаметром 100 мм; ленторез, ножницы, коточик, проволока, клей. Техника плетения этой конфетницы такая же, как при выполне нии круглой вазочки, только загибку ленточек через ободок дела ют одиночными зубцами. . Выплетают полотно 8 Х 8 ленточек и намечают донышко. Изготовление стенок изделия начинают с л ю бого угла. Подняв вертикально четыре ленточки, заплетают их между собой, чтобы высота угла составляла 2 клетки формируют остальные углы и плетут стенки конфетницы на высоту 4 клеток.
134
Загибка зубцами. Н адевают ободок, с лю бого угла пару лент перекрещивают между собой. Л евую ленточку перегибают через правую и пропускают под поперечную ниже ободка, а правую — через левую и также заправляют под поперечную ленту (ри с. 97, б ) . Таким образом, получается первый зубец. Затем делают по одному зубц у на каждом углу. Во время работы ободок должен бы ть расположен в плоскости, строго параллельной донышку изделия. Далее продолж а ют делать зубцы по периметру изделия. На этом заканчивается плетение первого слоя. Плетение второго слоя. Ленточки после загибки зубца заплетают по той дорож ке, по которой их плели в первом слое. Выплетая стенки конфетницы ниже обруча, ленточки подтягивают равномерно. Таким образом конфетницу заплетают до конца вторым слоем. Затем обрезаю т оставшиеся концы ленточек. Изделие можно украсить цветными дорожками, поясками, звездоч ками, выполненными ленточками контрастного цвета. Например, для отделки изделий темно-желтого или коричневого цвета можно взять белые (внешний цвет коры ) или светло-желтые ленточки. Пояски выполняют короткими (длиной 30— 40 мм) ленточками, но ширина их должна бы ть одинаковой с лентами изделия.
Конфетница двухцветная (рис. 98) Для плетения потребуются: 16 не очень тонких ленточек двусторонней расцветки шириной 12 мм, длиной 350—4 0 0 мм для плетения полотна 8 X 8 ; ободок из проволоки диаметром 115 мм; нож, ножницы, коточик, ленторез и клей. Техника плетения двухцветной конфетницы такая же, как и при выполнении вазочки и конфетницы. Различие состоит в том, что нижняя половина изделия выплетается в один, а верхняя — в два слоя, кроме того, иначе делается раскладка полотна. Ленты укладывают наружным (бел ы м ) слоем вверх, следователь но, внутренняя сторона изделия будет белой, а доныш ко и часть стенок — желтыми. Для плетения этой вазочки требуется особенно тщательная нарезка лент, плотная и точная раскладка полотна. Определив углы донышка, тупым шилом проводят линии, соединяющие углы. После чего прогибают полотно *по этим линиям, чтобы точно сформировать квадрат донышка, особенно его углы. Затем заплетают стенки изделия на вы соту 5 клеток, считая перпендикулярно вверх от угла, или 60 мм до ободка. Н адевают ободок и оплетают верх одиночными зубцами. Теперь каждую ленточку плетут по своей дорожке на 3 клетки и концы обрезают. На данном этапе работы вся внутренняя часть и 3 клетки снаружи выполнены белым цветом, доныш ко и две клетки стенок желтые. Для плетения можно использовать и односторонний материал, 135
Рис. 97. Конфетни-
Рис. 98. Конфетни ца двухцветная
особенно если в наличии имеются только короткие (длиной 300— 350 мм) ленты, длины которых не хватит, чтобы оплести всю конфетницу в 2 слоя. В этом случае изделие до середины плетут лентами одного цвета, а заканчивают работу ленточками другого цвета, чтобы получилась комбинированная конфетница в 2 слоя. В месте стыка лент концы обрезаю т острым ножом.
Вазочка с двойными зубцами (рис. 99, а) Для плетения понадобятся: 20 ленточек шириной 12 мм, длиной 500— 550 мм; ободок диаметром 140 мм, оплетенный берестой; ножницы, нож, ленторез, клей, коточик. Полотно 1 0 Х Ю ленточек выполняют, как сказано выше. Затем на полотне обозначают углы на стыке 5-й и 6-й ленточек. Длина должна составлять 100 мм. Стенки изделия заплетают первым слоем на высоту трех клеток, после чего надевают ободок (ри с. 99, б ) . Край изделия отделывают двойными зубцами. Для чего оплетают сначала углы. При выполнении двойных зубцов лентой / огибают ленты 3 и 4 и пропускают ее под поперечную ниже ободка по своей дорожке (ри с. 99, в ). Таким же образом заплетают ленту 3, огибая ею ленту 2 и / , пропуская далее по своей дорожке (ри с. 99, г ). Ленту 2 загибают за ленты 3 и 4 и также пропускают по своей дорож ке (рис. 99, д ). Лентой 4 огибают ленту 2, протаскивают ее под поперечной / и заплетают по своей дорожке до конца. Получился двойной зубец. Такой же зубец выполняют на противоположном углу, а затем на двух других. Стенки между углами оплетают тремя одиночными зубцами. Далее изделие полностью заплетают вторым слоем, аккуратно и равномерно подтягивают ленты, поскольку при малейшей перетяжке нарушится форма и возникнут провалы в стенках.
Маленькая цветочница (рис. 100, а) Для плетения потребуются: 12 двусторонних ленточек шириной 12 мм, длиной 300— 350 мм; ободок диаметром 90 мм, обернутый берестой; нож, ножницы, коточик, ленторез, проволока, клей. Полотно 6 Х 6 ленточек плетут, как описано выше. На готовом полотне определяют углы квадрата донышка, располо женные на стыке 3-й и 4-й клеточек с каждой стороны . Длина стороны квадрата — 55 мм. Коточиком прочерчивают линии между углами и прогибают стенки вверх. Д но и стенки выплетают однослойно. Выполнив стенки на высоту 110 мм, надевают ободок диаметром 70— 80, диаметр донышка — 60 мм. Затем делают на каждом углу по одиночному зубцу, а в проме137
Рис. 99. Вазочка с двойными зубцами: а — общий вид; б — д — порядок выполне ния двойного зубца; /— 4 — ленточки
а
В
Д
Рис. 100. Малень кая цветочница: а — общий вид; б — плетение украшения (цифрами и стрелками показаны порядок и направление работы); в — украшение плетения (цветочек)
жутках между ними — по одному двойному. После формирования зубцов ленточками проплетают 2 клетки и концы обрезают. Украшение на стенках изделия выплетают в виде цветочков с четырьмя лепестками (угольничками) цветными ленточками такой же ширины, заостренными с одного конца. Д ля чего на высоте 25— 30 мм на стенке изделия приподнимают коточиком клетку / (рис. 100, б ) и вставляют цветную ленточку 5 сверху вниз изнаночной стороной наружу под ленту / , оставив конец длиной 15— 20 мм. Затем отделочную ленту 5 перекручивают изнаночной стороной, подводят под поперечную ленточку 2 и натягивают (ри с. 100, в ). Таким образом, получается лепесток (угольн ичек). Далее ленточку опять перекручивают обратной стороной наружу, пропускают под клеткой 3 и в той же последовательности — под клеткой 4. Придерживая за оставшийся конец первого лепестка, протягивают ленточку 5 под клетку / и обрезаю т концы. Таким способом оформляют цветочками все четыре стороны изделия.
Большая цветочница (рис. 101, а) Для плетения потребуются: 16 ленточек шириной 12 мм, длиной 700— 750 мм; ободок из проволоки диаметром 120 мм, обмотанный берестой одного цвета с внутренней окраской цветочницы; 2— 3 лен точки шириной 12 мм, длиной 300— 350 мм другого цвета для отделки; ножницы, нож, коточик, ленторез, клей. И з бересты двусторонней расцветки выплетают полотно 8 Х 8 лен точек, доныш ко и стенки делают в один слой, зубцы — в два. Размер донышка по диагонали— 110 мм, высота стенок до ободка — 8— 9 клеток, или 150— 155 мм, диаметр донышка — 80 мм. Материал необходимо брать плотный. Одним из самых важных моментов в работе является плетение донышка; оно долж но бы ть очень плотным, чтобы цветочница стояла устойчиво и надежно. Верх изделия оформляют двойными зубцами. Украшение на стенках выплетают в виде цветочков (см . рис. 100, б, в ) на высоте 80 мм. К роме того, можно сделать поясок в виде угольников. Для чего отделочную ленту пропускают сверху под поперечную / (ри с. 101, б ) изнаночной стороной наружу, перекручивают ее цветной стороной вверх и протягивают под поперечной лентой 2. Для получения угольничка ленточку натягивают. Затем опять разворачивают обрат ной стороной и протягивают под поперечной лентой 3 (ри с. 101, в) и т. д. Таким сп особом оформляют поясок по окруж ности изделия. П оясок выполняют на первом и втором от ободка рядах клеток.
Рис. 101. Большая цветочница: а — общий вид; б, в — порядок выполнеия угольничков; /— 8 — клетки на полотне
а
б
в
Круглая коробочка (рис. 102) Для плетения потребуются: 16 ленточек шириной 10 мм, длиной 350— 400 мм; ленточка шириной 10 мм другого цвета для украшения; ободок из тонкой проволоки диаметром 75 мм; нож, коточик, ножницы, ленторез, клей. П олотно 8 Х 8 ленточек выплетают из тонкой, блестящей бересты односторонней расцветки. Плетение двухслойное. Размер донышка по диагонали — 75 мм, высота стенок до ободка — 3 клетки, или 45— 50 мм. Верх оформляю т одиночными зубцами, стенки — пояском. Цветной поясок на стенке коробочки. Отсчиты ваю т 3 клетки вниз от ободка по дорож ке и закрывают четвертую клетку ленточкой другого цвета. Для чего поднимают коточиком 3-ю и 5-ю поперечные ленты и под них пропускают цветную. Концы отделочной ленты обрезаю т острым ножом. Затем последовательно закрывают каждую 4-ю клетку по всей окруж ности изделия. Таким способом образовавш и еся цветные клетки соединяются в поясок. При этом можно чередовать отделочные ленты разных цветов, например белые и коричневые.
Конфетница, с двумя ручками (рис. 103, а) Для плетения потребуются: 16 ленточек шириной 12 мм, длиной 400— 450 мм; ленточка шириной 8 мм, длиной 350— 400 мм для закрепления дужек; отрезок ленточки с белой поверхностью длиной 90— 100 мм, шириной 6 мм для украшения оплетки дужек; ободок диа метром 115 мм с двумя ручками; нож, коточик, ножницы, ленторез, зажимы и клей. С пособ плетения этой конфетницы такой же, как конфетницы с зубцами. Выплетают полотно 8 Х 8 ленточек. Размер донышка по диагонали — 115 мм, сторона донышка — 80 мм, высота стенок — 60 мм, или 3 клетки, высота от донышка до ручек — 170 мм. Расцветку бересты выбирают по своему вкусу. С пособ плетения зависит от наличия материала двусторонней расцветки, который дает возмож ность выплетать лентами одного цвета один или два слоя, а также получать изделия, выполненные в два цвета. После заверше ния плетения полотна и формирования квадратного донышка пле тут стенки, затем надевают ободок с двумя ручками. Ручки должны располагаться по центру стороны между двумя углами. Сначала заплетают одиночными зубцами дужки, расстояние между дужками на ободке не должно быть более 30 мм. К аж дую дуж ку заплетают одним зубцом (ри с. 103, б ) . Слева и справа по кругу ободка заплетают с каждой стороны по 6 зубцов. Окончив оформление вазочки зубцами, продолж ают заплетать ниже обруча все концы ленточек вторым слоем. 142
Если оставляют низ вазочки однослойным, то проплетают 3 клетки и обрезаю т концы. После чего соединяют дужки вверху и закрепляют ленточкой. О своив плетение конфетницы, можно делать их, по-разному оформляя верх, используя комбинированный цвет лент. Например, заплетают каждую дуж ку отдельным зубцом, а слева и справа от дужек по кругу делают прямую загибку через ободок или чередуют два одиночных зубца и один двойной. Сочетание цветов выбирают также по своему вкусу.
Сухарница (рис. 104, а) Д ля плетения изделий продолговатой формы необходимо сделать полотно нужного размера, из которого формирую т прямоугольное донышко. Для плетения потребуются: 28 лент шириной 12 мм, длиной 600— 650 мм; две ленты шириной 12 мм, длиной 300— 350 мм другого цвета для украшения; ободок овальной формы, больший диаметр — 210 мм, меньший — 150 мм; нож, ножницы, коточик, ленторез, за жимы, клей. Подготовленный ободок из проволоки обматывают берестяными лентами того же цвета, как изделие. Плетение полотна. Переплетают первые 4 ленты, как показано на рисунке 89. П родолж аю т заплетать по одной ленте с каждой стороны , уплотняя их пальцами и проверяя по линейке расстояние между ними. В таком порядке заплетают все 28 лент. П олучают полотно 14х 14 лент. На уплотненном полотне, закрепленном зажимами на всех 4 углах, определяют горизонтальные и вертикальные точки, они расположены на стыке 7-й и 8-й ленточек со всех сторон (ри с. 104, б ) . Расстояние между точками — 230— 235 мм. Теперь необходимо наметить прямо угольное донышко. На стыке 5-й и 6-й ленточек ставят точки. Тщ ательно проверяют расстояние между углами и точками, оно долж но бы ть абсолю тно одинаковым. Затем тупым шилом или коточиком намечают линии будущ его донышка, как показано на рисунке 104, б. Ч тобы сформировать донышко, по линиям, прочерченным между углами, прогибают берестяное полотно, поднимая его вверх. Плетение углов и стенок на вы соту 3 клеток выполняют в обычной последовательности. Во время работы аккуратно подтягивают ленточ ки, не допуская перетяжек и слабины. На высоте 3 клеток надевают ободок. Загибку ленточек через ободок делают прямую. Закончив оформление верха сухарницы, продолж ают заплетать ленты на всю длину, образуя второй слой плетения. Если некото рые ленточки окажутся короткими, их наращивают. 144
а
Рис. 104.
Сухарница: а — общин вид; б — разметка прямоугольного донышка; / — горизонтальные точки; 2— вертикальные точки; А, Б — углы прямоуголь ного донышка
На удлиненных стенках сухарницы для отделки выплетают по одному цветочку ленточками другого цвета. Сухарницу можно сплести из ленточек двух цветов. Для чего после загибки через ободок проплетают 2 клетки и обрезаю т все концы, остальную часть стенок и доныш ко заплетают вторым слоем бересты другого цвета. Верх сухарницы оформляю т одиночными зубцами или чередуют одиночные зубцы с двойными в определенной последовательности. Сухарницу можно сделать с тремя ручками.
Конфетница с тремя ручками (рис. 105, а) Для плетения потребуются: 8 ленточек темного и 20 светлого цвета (или н аоборот) шириной 12 мм, длиной 600— 650 мм; 2 ленточки шириной 12 мм, длиной 300 мм для украшения; 4 ленточки шириной 12 мм, длиной 250— 300 мм для ножек; цветная и белая ленточки шириной 7 мм, длиной соответственно 300 и 100 мм для закрепления ручек; ободок из алюминиевой проволоки длиной 210 мм, шириной 150 мм с тремя ручками (ри с. 9 3 ); нож, ножницы, коточик, ленторез, приспособление для заготовки прямоугольных ободков, зажимы, клей. Конфетницу делают так же, как сухарницу продолговатой формы. К оличество и раскладка лент, плетение полотна, разметка донышка совпадают с техникой изготовления сухарницы. Для полотна 14Х 14 ленточек сначала заплетают 8 лент одного и 20 лент другого цвета. Разметка донышка показана на рисунке 104, 6. При плетении первого слоя на высоте 3 клеток надевают ободок с тремя продольными или поперечными (п о своему усмотре н ию ) ручками, оплетенными берестяными ленточками нужной рас цветки. Затем оформляют верх изделия зубцами. Заплетают среднюю дуж ку двойными зубцами, а две крайние — одиночными. П роверяют ровность крепления ободка и удлиненные боковые стенки заплетают одиночными зубцами. С каждой стороны долж но получиться по 10 зубцов. Плетение второго слоя. Заплетая конфетницу вторым слоем, на углах оставляют незаплетенными по две ленточки / и 3 для ножек (ри с. 105, б ) . Ножки делают после того, как изделие будет заплетено вторым слоем полностью. Ленточки 1 и 3 должны перекрещиваться между собой на углах, где и ф ормируют ножки. Ленту 3 перегибают под уг лом и обратной стороной вставляют под ленту / (ри с. 105, в), а ленту / проводят под ленту 3 по ее дорож ке (ри с. 105, г ). Для закрепления ножки берут ленточку 4 длиной 150 мм (одн ого цвета с внутренними) и заостренным концом продевают ее сверху вниз под поперечные лен ты / , 2 и 3 (ри с. 105, д ). 146
Затем снова продевают ленточку 4 в обратном направлении, сверху ленты / и снизу под поперечную 2 цветной стороной наружу (ри с. 105, е ). Таким образом закрепляют ножку и образую т клетку. П осле чего закрепляют ручки вверху ленточками. Украшение в виде цветочков выплетают на удлиненных стенках конфетницы.
Большая хлебница (рис. 106, а) Для плетения потребуются: 32 ленточки односторонней расцветки шириной 12 мм, длиной 650— 700 мм; ободок диаметром 215 мм из проволоки толщиной 3,5 мм, оплетенный берестой того же цвета, как и все изделие; ножницы, коточик, ленторез, зажимы, клей. Для плетения полотна 16Х 16 раскладывают ленточки темной стороной вверх. При этом следят за ровностью укладки. Закончив плетение, закрепляют углы зажимами. На готовом полотне размечают донышко. Расстояние между углами полотна по диагонали долж но бы ть 230— 235 мм. Горизонтальные и вертикальные точки находятся на стыке 8-й и 9-й ленточек с каждой стороны полотна (ри с. 106, б ) . Длина стороны дон ы ш ка — 145— 150 мм. Линии, определяющие квадрат донышка будущ его изделия, чертят тупым шилом с обратной стороны , поскольку у хлебницы открытое донышко и на лицевой стороне разметка будет видна. Стенки заплетают на вы соту 2 клеток, начиная с лю бого угла, и закрепляют зажимами, затем формирую т противополож ный и остальные углы. После чего надевают ободок. Верх хлебницы оформляют одиночными зубцами. Сначала заплета ют по одному зубц у на каждом углу, проверяют ровность крепления ободка, стенки между углами также заплетают зубцами, а всю хлебницу — вторым слоем. Верх хлебницы можно оформить и прямой загибкой через ободок или чередуя одиночные зубцы с двойными. При этом на каждой стенке изделия получится по 4 двойных зубца. Очень красиво выглядит изделие при комбинированном плетении. Например, первые 12 ленточек полотна берут темной окраски (коричневой, темно-коричневой), остальные 20 ленточек — желтые или белые. Э ту хлебницу делают и на ножках.
Хлебница на ножках (рис. 107) Для плетения потребуются: 8 коричневых и 12 желтых или светло-ж елтых ленточек шириной 17 мм, длиной 550— 600 мм; ободок диаметром 180 мм из проволоки толщиной 3— 3,5 мм; 4 коричневых 149
ленточки шириной 17 мм, длиной 150 мм для крепления ножек изделия; ножницы, коточик, ленторез, зажимы, клей. Ленточки для плетения полотна заостряю т с обоих концов, а для крепления ножек — с одной. П роверяю т ширину лент. О бод ок оплетают желтой ленточкой. П олотно 1 0Х Ю ленточек выплетают как обычно, только сначала укладывают 8 коричневых, а затем 12 светло-ж елтых ленточек. Закончив плетение полотна, определяют углы (разм ечаю т точки на доныш ке) — они находятся на стыке 5-й и 6-й ленточек с каждой стороны . П осле чего приступают к плетению стенок на вы соту 2 клеток. Затем надевают ободок, закрепляют верх одиночными зубцами и выплетают всю хлебницу вторым слоем. Т ол ько на углах оставляют незаплетенными ленты / и 3 (см . рис. 105) для ножек. Д ля украшения на каждой ножке выплетают цветочки берестяными ленточками другого цвета.
Маленькая хлебница (рис. 108) Для плетения потребуются: 12 тонких ленточек темного и 20 свет лого цвета (или н аоборот) шириной 10 мм, длиной 450— 500 мм; ободок из проволоки диаметром 170 мм, оплетенный берестой; ножницы, коточик, ленторез, зажимы и клей. Плетение полотна. Заготовленные ленточки заостряю т с обоих концов и тщательно проверяют их ширину, только после этого приступают к плетению полотна. При раскладке полотна 1 6Х 16 ленто чек сначала укладывают, переплетая, 12 ленточек одного цвета, а затем 20 — другого. Закончив плетение полотна, на стыке 8-й и 9-й ленточек намечают углы донышка (см . рис. 106, б ) . Стенки заплетают на вы соту 2 клеток. После чего надевают ободок и оформляют верх изделия: углы — двойными, а стенки — одиночны ми зубцами. При этом на углах должны получиться зубцы одного, а на стенках — другого цвета. Заплетая хлебницу вторым слоем, постоянно подтягивают ленточки и следят, чтобы не бы ло перетяжек и слабины. При точном соблюдении техники плетения хлебница должна выглядеть легкой, изящной, с красивой расцветкой внутри.
Маленькая сухарница (рис. 109) Для плетения потребуются: 20 тонких, мягких ленточек одного Цвета шириной 17 мм, длиной 450— 500 мм; ободок диаметром 190 мм из проволоки толщиной 3— 3,5 мм, оплетенный берестой; ножницы, коточик, ленторез, зажимы, клей. 151
Рис. 107. Хлебница на ножках
Рис. 109. Малень кая сухарница
П осле плетения полотна 10Х 10 ленточек определяют углы будущ его донышка. Они расположены на стыке 5-й и 6-й ленточек. Начиная с углов, заплетают первым слоем всю сухарницу на вы соту одной клетки. Н адевают ободок и оформляю т верх прямой загибкой парными ленточками. Затем последовательно заплетают вторым слоем углы, стенки и донышко. Причем не сразу каждую стенку заплетают целиком, а поочередно, выполняя по одной клетке с одной стороны , затем с противоположной и т. д. Во время плетения необходимо следить за ровностью крепления ободка. Верх оформляют прямой загибкой. Оставш иеся концы ленточек аккуратно обрезаю т, чтобы они не торчали из-под поперечных лент.
Ваза с ромбиками (рис. 110, а) Не применяя дополнительных украшений, а пользуясь переплете нием и укладкой лент разной расцветки, можно получить красивые изделия. Для плетения потребуются: 16 бело-желтых ленточек двусторонней окраски длиной 350— 400 мм, шириной 12 мм и 16 таких же бело коричневых; 2 ленточки ж елтого цвета шириной 12 мм, длиной 450— 500 мм для отделки; берестяной тонкий пласт шириной 150 мм, длиной 380— 400 мм для придания ж есткости изделию; ободок диаметром 120— 125 мм, оплетенный желтой ленточкой; ножницы, коточик, ленторез, нож, зажимы и клей. О собен ность этой вазы состоит в том, что материал необходимо подбирать двусторонней расцветки, желательно белый и желтый или белый и коричневый. К аж дую из 16 ленточек белой окраски склеивают с коричневой, чтобы образовались двухцветные ленты длиной 750— 800 мм. При склейке ленточек одну из них кладут вверх белой, другую — коричневой стороной. В месте склейки на концах ленточек снимают остры м ножом слой бересты длиной 10 мм, смазывают клеем, соединяют ленты и ставят груз до полного высыхания. П олотно выплетают, как показано на рисунке 110, б. Ч тобы получить нужный рисунок на изделии, следует точно соблю дать последовательность раскладки лент. Остальные белые ленты приплета ют к белым, коричневые к коричневым. Ленты постоянно уплотняют пальцами, расстояние между ними проверяют по линейке. Так заплетают все 16 ленточек. На готовом полотне размечают квадратное доныш ко со стороной 100Х ЮО мм. П олотно прогибают вверх и выплетают стенки. На высоте 9-й клетки надевают ободок и оформляю т верх двойными зубцами. Концы ленточек заправляют за поперечную ленту ниже ободка и обрезаю т. Для усиления ж есткости стенок из тонкого берестяного пласта делают цилиндр, промазывают края пласта клеем и вставляют внутрь цветочницы. 153
а
Рис. 110. Ваза ромбиками; а — общий вид; 6 — раскладка лент: Б — белые ленты; Т — темные ленты
В верхней части цветочницы, отступив на 1 клетку от ободка, выплетают поясок в виде угольничков лентами другого цвета (см . рис. 101, б, в ).
Круглая ваза для цветов (рис. 111, а) Плетение круглых изделий из берестяных ленточек довольно редко применяется в прикладном искусстве, т. к. выполнить это достаточно сложно. Однако, хотя стенки и верх изделия делают круглыми, форма донышка остается прямоугольной. П оскольку для плетения ножек доныш ко прорезают, внутрь готового изделия вставляют стеклянную банку или стакан. Для плетения потребуются: 16 ленточек односторонней расцветки шириной 12 мм, длиной 600— 650 мм; 2 ободка из проволоки диаметром 120 и 125 мм; ножницы, коточик, ленторез, зажимы, скрепки, клей. После плетения полотна 8 Х 8 ленточек определяют углы донышка. Они расположены на стыке 4-й и 5-й ленточек с каждой стороны . На лицевой стороне полотна вычерчивают квадрат будущ его донышка. П рогибают полотно по линиям, поднимая его вверх. Затем заплетают стенки на вы соту 12 клеток, надевают ободок диаметром 125 мм. Верх вазы оформляют одиночными зубцами и заплетают на 5— 6 клеток ниже ободка второй слой. Теперь необходимо придать округлость стенкам вазы и решить, на чем она будет стоять и как в ней должна держаться банка для цветов. С низу на изделие надевают ободок диаметром 120 мм, поднимают его на вы соту 3-й клетки и закрепляют канцелярскими скрепками. После чего на дне изделия все ленточки разрезаю т с угла на угол (рис. 111, б ) , плетение распускают до ободка (вы сота стенок вазы — 9 клеток). Концы лент заостряю т и делают загибку одиночными зубцами. При выполнении одиночного зубца ленточки не вплетают в корпус, отгибают зубец внутрь, чтобы он принял горизонтальное положение. Л евую ленточку (она находится сверху) загибают под правую и вставляют под поперечную, а правую накладывают на левую, также пропускают под поперечную и затягивают обе ленточки. Так получился первый ромбик-ножка. Такие ромбики-ножки выплетают по всему ободку (ри с. 111, в ). Концы ленточек заплетают вторым слоем и обрезаю т ножом. Все 16 ромбиков-нож ек должны находиться в горизонтальном положении для устойчивости вазы. Если стенки изделия получились слабыми, из тонкой бересты склеивают цилиндр по размеру вазы и вставляют его внутрь для прочности. Украшения на стенке выплетают по своему вкусу. Стенки круглой вазы для цветов можно выплетать, как вазу с ромбиками (см . рис. 110), только работу следует выполнять в один слой.
Круглая ваза для цветов:
Рис. 111.
а — общий вид; б — разрез донышка по диагоналям; в — ромбики-ножки вазы (вид снизу)
а
Солонка на ножках (рис. 112) Маленькое изделие сделать труднее, т. к. много времени уходит на подготовку материала, а плетение требует больш ого терпения и мастерства. Для плетения потребуются: 12 ленточек длиной 350— 400 мм, шириной 12 мм; 4 ленточки длиной 150 мм, шириной 12 мм для крепления ножек; ободок из проволоки диаметром 75— 80 мм; ленточки шириной 12 мм другого цвета для украшения; ножницы, нож, коточик, ленторез, зажимы, клей, расклинивающий шаблон (см . рис. 8 7 ). Подготовка материала. Н арезают необходимое количество ленто чек, заостряю т их с обоих концов, проверяют ширину. Делают ободок, оплетают его берестяными ленточками под цвет изделия. Плетение двухслойное, материал использую т односторонней рас цветки. Цвет бересты выбирают по своему вкусу. Плетение полотна 6 Х 6 ленточек показано на рисунке 89. На гото вом полотне намечают донышко, углы его расположены на стыке 3-й и 4-й ленточек с каждой стороны . Плетение стенок. Поднимая полотно вверх по линиям, заплетают солонку на вы соту 3 клеток. Н адевают ободок и делают прямую загибку. Затем заплетают все изделие вторым слоем, оставляя на каждом углу по 2 ленточки, не заплетенными для ножек. Н ож ки выполняют, как показано на рисунке 105. Основная слож ность в работе над солонкой состоит в том, что стенкам изделия нужно придать выпуклую форму. Д остигаю т этого с помощ ью расклинивающего шаблона. Диаметр ободка должен бы ть на 10— 15 мм меньше донышка по диагонали. Во время плетения надо при креплении ободка придать нуж ную форму стенкам, проминая их пальцами. Украшение на стенках в виде пояска из угольничков делают по двум поперечным ленточкам, отступая вниз на 1 клетку от ободка (см . рис. 101, б, в ).
Маленькая солонка (рис. 113) Для плетения потребуются: 16 ленточек длиной 400— 450 мм, шириной 10 мм для полотна 8 X 8 ; ленточки из тонкой бересты другого цвета для украшения стенок; ободок из проволоки диаметром 75— 80 мм; ножницы, нож, ленторез, зажимы, клей, коточик. Все операции выполняют так же, как при плетении маленькой солонки на ножках, только ножки не делают. Плетение двухслойное. Солонка должна бы ть выпуклой формы. Стенки выплетают на высоту 3 клеток. Верх оформляют прямой загибкой двумя ленточками или одиночными зубцами. 157
а
Р ис. 112. Солонка на ножках Р ис. 113. Малень кая солонка Р ис. 114. Ваза для фруктов: а — общий вид; б — плетение украшения
Рис. 115. Вазочка для печенья
Для украшения выплетают угольники по центру изделия. Цвет бересты выбирают по своему вкусу.
Ваза для фруктов (рис. 114, а) Э то изделие по технологии совпадает с плетением вазы с тремя ручками. Разница лишь в размере, форме, количестве ленточек, в ободке и украшении на стенках вазы. Для плетения потребуются: 36 желтых или темно-желтых ленточек односторонней расцветки длиной 650— 700 мм, шириной 12 мм; белые или желтые ленточки шириной 12 мм двусторонней расцветки для украшения стенок; овальный ободок (больш ий диаметр — 240— 245 мм, меньший 180— 185 мм) с тремя ручками длиной 550 мм из проволоки сечением 35— 40 мм; тонкие белая и цветная ленточки для закрепления ручек сверху; ножницы, нож, коточик, ленторез, зажимы, клей, линейка. Выплетают полотно 18Х 18 ленточек, закрепляют углы зажимами. Намечают донышко, углы его находятся на стыке 8-й и 9-й клеточек с каждой стороны . Чертить рекомендуется с изнаночной стороны полотна, на лицевой можно только разметить уголки. Затем прогибают полотно по линиям. Плетение стенок. Вазу заплетают первым слоем на высоту 3 клеток и закрепляют работу 8 зажимами. После чего оплетают ленточками ободок, ручки и надевают ободок на изделие. Удлиненные стенки оформляют прямой загибкой парными лентами. Боковые ручки заплетают двойными, а средню ю — тройными зубцами. На оплетку ручек требуется 14 пар ленточек (с каждой стороны по 7 ). Остальные 22 заплетают прямой загибкой через ободок ( с каждой стороны по 11 пар). Заплетая вазу вторым слоем, оставляют на каждом углу по 2 незаплетенные ленточки для ножек. Н ож ки выплетают, как показано на рисунке 105. Прежде чем соединить ручки, загибают их дугой. После чего при помощи ленточек и клея соединяют дужки наверху (см . рис. 9 5 ). Украшение на стенках выплетают лентами в виде широкого пояса вокруг всей вазы, чередуя темный и белый цвет. Такая отделка придает изделию более нарядный вид и увеличивает его прочность. Д ля плетения украшения ленточку с заостренным концом вставля ют сверху вниз темной стороной наружу под поперечную ленту ниже ободка и пропускают ее под следую щ ую поперечную на всю длину (ри с. 114, б ) . Затем перегибают ленточку, поворачивая белой стороной наружу, подводят под поперечные ленты по диагонали вверх до ободка. Снова перегибают ленточку, поворачивая темной стороной наружу, пропускают под поперечные ленты вниз, так же, как делали сначала, опять поворачивают белой стороной и т. д. до тех пор, пока вся ваза не будет заплетена по окруж ности сплошным поясом. Вверху 160
и внизу темные ленты перегибают строго на одной линии, иначе рисунок будет неровным. Ленточки для украшения нарезают от одного пласта, что гарантирует совпадение их по цвету.
Вазочка для печенья (рис. 115) Для плетения потребуются: 36 гладких тонких ленточек одн осто ронней расцветки шириной 10 мм, длиной 450— 500 мм для полотна; ленточки такого же размера двусторонней расцветки для украшения стенок; ободок с тремя ручками из алюминиевой проволоки толщиной 2,5— 3 мм, длиной 195 мм, шириной 135 мм (см . рис. 94, а ), опле тенный берестяными лентами под цвет изделия; тонкая белая ленточка длиной 120 мм и темная длиной 450— 500 мм для закрепления ручек вверху; ножницы, нож, ленторез, коточик, 8 зажимов и клей. Выплетают полотно 1 8 Х 18 ленточек, размечают донышко, углы его находятся на стыке 8-й и 9-й ленточек с каждой стороны . Н еобходимо тщательно проверить расстояние между углами по диагонали, только после этого прочертить донышко будущ его изделия с изнаночной стороны. Прогибают полотно по линиям, чтобы легче было заплетать стенки. Если доныш ко вазочки будет отделано цветной лентой, то украшение делают прямо на полотне до начала плетения углов и стенок изделия. Для чего выплетают квадрат из берестяных ленточек другого цвета, а в середине него — цветочек с четырьмя лепестками, вось миконечную звездочку и т. п. Плетение стенок. Начиная с углов, заплетают вазочку первым слоем на высоту 3 клеток и закрепляют зажимами. Н адевают ободок с ручками и последовательно оплетают средню ю ручку двойными, а боковые — одиночными зубцами, верх изделия, боковые и удли ненные стенки оформляют одиночными зубцами. Заплетая вазу вторым слоем, на каждом углу оставляют по 2 незаплетенные ленточки для ножек. Ножки делают после полного завершения плетения изделия вторым слоем. С п особ плетения ножек показан на рисунке 105. Прежде чем приступить к закреплению ручек вверху, их дугообразно выгибают, придав им красивый вид. После чего при помощи ленточек и клея закрепляют ручки. Для украшения стенок нужны гладкие ленточки двусторонней расцветки — белые и темные, которыми выплетают широкий пояс по периметру вазочки (см . рис. 114, б ) . Чередование белых и темных лент придает изделию красивый вид и увеличивает его прочность.
Изготовление изделий из берестяного пласта Туески (ряс. 116) С ущ ествует несколько сп особов изготовления туесков. Первый способ. Т уесок делают из цельной, т. е. бесшовной внутренней части и наружной пластовой, соединяющ ейся швом, так называемым замочным креплением. Такой туесок использую т для хранения жидких и бы стропортящ ихся продуктов. Д л я р а б о т ы п о т р е б у ю т с я : сколотень диаметром 100— 120 мм, вы сотой 180— 200 мм для внутренней части туеска; берестяной пласт длиной 400— 450 мм, вы сотой 150 мм для обш ивки сколотня; лист тонкого картона или бересты длиной 400— 450 мм, высотой 150 мм; полоски берёсты шириной 25— 30 мм, длиной 440— 450 мм для поясков; доска из древесины ели, кедра или сосны толщиной 15— 20 мм для изготовления крышки и донышка; ивовый прут длиной 300— 350 мм для ручки; нож, коточик, лобзик или пилка, дрель, линейка, циркуль, клей. П о д г о т о в к а м а т е р и а л а . Н аруж ную часть бересты тщатель но очищ ают от мелких кусочков коры. Внутренняя часть сколотня должна бы ть чистой без наплывов и трещин, одинаковой высоты по всей окруж ности. Вы резаю т точно по размеру средню ю прокладку из картона. Берестяной пласт для наружной обшивки берут вы сокого качества. И з г о т о в л е н и е т у е с к а . Края берестяного пласта соединяют замочным креплением. Лучше сначала потренироваться на короткой или некачественной бересте. Берестяной пласт по длине подбирают к сколотню таким образом, чтобы вертикальные края заходили друг за друга на 30— 35 мм. Д ля соединения краев надевают на сколотень обш ивку изнаночной (тем н ой ) стороной наружу, шилом намечают по 2 точки на каждом краю и соединяют точки прямой линией. Вдоль этих линий вырезают ножом сквозны е треугольные отверстия, причем углы, направленные к центру полотна, должны бы ть сдвинуты относительно друг друга и проходить по центру между противоположными треугольниками. Д ля облегчения работы крепление лучше сначала разметить по трафарету. Трафарет вычерчивают на обычном тетрадном листке в клеточку длиной 320 мм (6 5 — 66 кл еток), шириной 190 мм (3 9 — 40 кл еток). Л ист кладут перед собой, развернув его горизонталь но по длине (ри с. 117, а). Разметку начинают с нижнего левого угла. О тступив 5 клеток слева и 1 снизу, вычерчивают основание равно бедренного треугольника, длина основания — 2 клетки (1 0 м м ). Таким образом размечают основания до верха страницы, размещая их на расстоянии 2 клеток (1 0 мм) друг от друга. Боковые стороны треугольника равны 15 мм, острый угол направлен вправо. 162
Затем с правой стороны листа отступаю т от нижнего края на 3 клетки (1 5 м м ), а от правого — на 5 клеток (2 5 мм) и вычерчивают такие же треугольники, расположенные зеркально (остры м углом налево). Все треугольники аккуратно вы резают остры м ножом. Трафарет накладывают на место шва, чтобы основания треугольни ков Проходили по намеченной линии.
Ш илом или иголкой накалывают точки в углах треугольников и по разметке вы резают треугольники на бересте ножом. С противопо ложного края бересты так же размечают и вырезают треугольники. При этом на одной стороне окажется на 1 треугольник больше. З д есь делают продольные разрезы (ри с. 117, б ) . Таким образом, получаются шипы для замочного крепления. Сгибая шипы полукругом, вставляют их сверху в отверстия противополож ного края бересты так, чтобы они оказались с внутрен ней стороны обшивки. Д ля придания жесткости в туесок вставляют средний тонкий пласт бересты или тонкий картон. Размеры этой прокладки соответствую т размерам наружной обшивки, но края ее не должны заходить друг за друга. Вставляя картон в берестяной цилиндр, следят за тем, чтобы стык картонных сторонок не совпал со швом. После чего надевают обшивку, скрепленную замком, размещая ее так, чтобы край сколотня выступал снизу больше, чем сверху (ри с. 118). Затем нижний край сколотня распаривают в горячей воде, отчего береста становится мягкой и эластичной, край загибают наружу, чтобы он плотно обхватывал обшивку. Т о же самое делают с верхней стороны сколотня. Д оны ш ко и крышку выполняют из древесины ели, кедра или сосны. Сначала промеряют циркулем внутреннюю окруж ность туеска, размечают на доске и выпиливают кружок. Для того чтобы доныш ко было плотно охвачено берестяными стенками, его выпиливают с припуском 2— 3 мм. Нижний край сколотня распаривают в горячей воде и вставляют в него донышко. Для увеличения прочности на верхнюю и нижнюю части туеска надевают пояски из бересты шириной 25— 30 мм, соединяя их замочным креплением. К ры ш ку подгоняют точно по размеру, чтобы она плотно закрывала туесок. В крышке просверливают 2 отверстия для ручки. Д угой сгибают ивовый прут и плотно вставляют его в отверстие. С внутренней стороны крышки на концах прута делают отверстия и закрепляют их поперечными палочками (ри с. 119). Гладкую поверхность туеска и пояски можно украсить резьбой и тиснением. Второй способ. Внутреннюю и наружную часть соединяют швами. Такой туесок использую т для сыпучих продуктов. Техника изготовления этого туеска такая же, как описано выше. Т ол ько вместо сколотня использую т цилиндр с замочным креплени ем. Д л я р а б о т ы п о т р е б у ю т с я : 2 берестяных пласта длиной 163
Р ис. 116. Туески
ттг.
Рис. 119. Крепле ние ручки
460— 480 мм, шириной 200 мм (для внутреннего цилиндра) и длиной 480— 500 мм, шириной 160 мм (дл я н аруж ного); тонкий картон длиной 480— 500 мм, шириной 160 мм для внутренней прокладки; полоски бересты шириной 25— 30 мм, длиной 480— 500 мм для поясков; доска из древесины ели или сосны толщиной 15— 20 мм для крышки и донышка; ивовый прут длиной 300— 350 мм для ручки' нож, коточик, лобзик или пилка, дрель, линейка, циркуль, клей. Сначала делают внутренний цилиндр диаметром 120— 130 мм, соединяя края замочным креплением так, чтобы шипы оказались снаружи. Сверху надевают картонную прокладку и наружный цилиндр. Затем верх и низ заготовки распаривают в горячей воде и загибают края на наружную обшивку. Д оны ш ко и крышку вставляют в распаренный нижний край, а крышку вставляют в сухой верхний. Верхний и нижний края туеска крепят поясками, соединенными швом. Третий способ. Края внутреннего цилиндра скрепляют водостой ким клеем типа «С уперцемент», а наружный — замочным креплением. Техника изготовления туеска такая же, разница в том, что сначала делают наружную обш ивку цилиндра с замочным креплением, по нему подгоняют прокладку и внутренний цилиндр, скрепленный клеем. Для работы потребуются: берестяной пласт длиной 420— 400 мм, шириной 150 мм для наружного цилиндра; средняя прок ладка из тонкой бересты или картона для ж есткости; берестяной пласт длиной 400— 420 мм, шириной 180— 200 мм для внутреннего ци линдра; полоски бересты шириной 25— 30 мм, длиной 420— 440 мм для поясков; доска из ели для крышки и донышка; ивовый прут для руч ки; деревянная цилиндрическая распорка диаметром 100— 120 мм, вы сотой 200— 220 мм; нож, коточик, лобзик или пилка, дрель, ли нейка, циркуль и клей. И з подготовленной бересты делают наружную обш ивку (ци ли ндр) диаметром 100 мм. Затем вставляют по размеру картонную прокладку. Внутренний цилиндр подгоняют по внешнему таким образом, чтобы вертикальные края заходили друг за друга на 10— 15 мм (и х закрепляют клеем). Высота его должна бы ть больше высоты наружной обшивки на 50— 60 мм. В собранный туесок вставляют деревянную распорку и оставляют ее до полного высыхания клея. Вся последующ ая работа проходит в обычной последовательности. Затем туесок сушат с открытой крышкой.
Шкатулка круглая (рис. 120, а) С п особ изготовления круглой шкатулки совпадает с третьим сп особом изготовления туеска. Сначала готовят наружную обшивку, закрепленную замочным креплением, и по ней подгоняют внутренний цилиндр, края которого склеивают. Выпиливают 2 кружка из дерева для донышка и крышки Н аруж ную часть шкатулки оформляют украшением из поясков. 166
Ввиду того, что шкатулка небольш ого диаметра, средню ю часть из картона или тонкой бересты не делают. Для работы потребуются: берестяной пласт односторонней расцвет ки длиной 240— 250 мм, шириной 65 мм для наружного цилиндра; берестяной пласт длиной 240— 250 мм, шириной 70 мм для внутреннего цилиндра; берестяные пояски для украшения стенок: 2 — шириной 40 мм (белы й и цветной), 2 — шириной 25 мм (белы й и цветной), 1 — цвета шкатулки шириной 20 мм; для украшения крышки: 1 — белого цвета и 1 — цвета шкатулки шириной 17— 18 мм; берестяные кружки для украшения крышки: 2 — белый и цветной диаметром, равным диаметру крышки, или 100— 120 мм; 2 — белый и цветной диаметром 50 мм; 2 — белый и цветной диаметром 35 мм; доска толщиной 10— 12 мм для донышка и крышки; деревянная цилиндрическая распорка диаметром 100— 110 мм, высотой 120— 150 мм для крепления внутреннего цилиндра; нож, коточик, лобзик или пилка, шило, цир куль, линейка и клей. Изготовление корпуса шкатулки. И з берестяного пласта высотой 60— 65 мм делают наружную обшивку диаметром 65 мм с замочным креплением (см . рис. 117). Внутренний цилиндр подгоняют по внешнему так, чтобы верти кальные края заходили друг за друга на 10— 12 мм. Смазы вают их клеем и вставляют в наружную обш ивку так, чтобы нижний край его был на уровне края обшивки, а верх выступал на 4— 5 мм (ри с. 120, б ) . После чего вставляют распорку до высыхания клея. При изготовлении донышка измеряют окруж ность шкатулки и выпиливают по этому размеру деревянный кружок. Д оны ш ко можно вставить в распаренный нижний край шкатулки, но лучше плотно подогнать его и закрепить клеем. Затем измеряют наружный диаметр верха внутреннего цилиндра шкатулки и выпиливают по этому размеру с припуском 2— 3 мм круж ок для крышки. Украшение стенок и крышки шкатулки поясками. Длину поясков определяют по диаметру изделия. Сначала надевают белый поясок по центру шкатулки, концы его соединяются швом или клеем, сверху белого надевают цветной. На цветном пояске предварительно шилом вычерчивают зубцы длиной 4— 5 мм и вырезают острым ножом (ри с. 120, в ). М еста соединения поясков не должны совпадать. Сверху на них точно так же надевают еще одну пару поясков меньшей ширины, а затем — еще один более узкий цвета шкатулки. К ры ш ку шкатулки с торца оклеивают поясками. Сначала крепят белый поясок, его верхний край должен бы ть на уровне верхнего края крышки. Второй поясок (с зубцам и) подгоняют сверху белого и закрепляют замочным креплением темной стороной наружу. При этом, если точно соблю дены все размеры, крышка должна свободно вставляться в шкатулку. На крышку наклеивают кружок из бересты белой расцветки, диаметр которого равен диаметру крышки. На лицевой стороне сверху белого кружка крепят темный такого же диаметра, но с зубцами. 167
а Рис. 120. Шкатулка круглая:
Сверху наклеивают еще 4 кружка (белы е и темные с зубц ам и ): 2 — диаметром 50 мм, 2 — диаметром 35 мм. Заверш ают украшение крышки маленьким (диаметром 30 мм) кружком из темной бересты (ри с. 120, г). Д оны ш ко снаружи и изнутри оклеивают берестяными кружками.
Большая круглая шкатулка (рис. 121) Для работы потребуются: берестяной пласт длиной 320— 340 мм, шириной 55 мм для наружной обшивки; пласт длиной 300 мм, шириной 65 мм для внутреннего цилиндра; берестяной пласт двусторонней расцветки длиной 350— 400 мм, шириной 100— 150 мм для украшения стенок изделия и крышки; доска толщиной 10— 12 мм для крышки и донышка; деревянная цилиндрическая распорка диаметром 80 мм, длиной 150 мм; нож, коточик, шило, пилка, циркуль, линейка и клей. Сначала делают наружный цилиндр диаметром 80 мм, высотой 55 мм. Берестяной пласт для внутреннего цилиндра подгоняют по внешнему так, чтобы вертикальные края находили друг на друга на 10— 12 мм. Высота внутреннего цилиндра — 65 мм. И з дерева выпиливают круж ок для донышка по внутреннему диаметру цилиндра и круж ок для крышки с припуском 2— 2,5 мм. Д ля украшения стенок, вырезают 2 пояска шириной 40 мм один белого, другой темного цвета, 2 пояска (белы й и цветной) шириной 35 и 1 цветной — 15 мм. Длину поясков определяют по диаметру шкатулки. Края темных поясков вы резают зубцами. Для украшения торцевой части крышки готовят 2 пояска шириной 170— 180 мм: один белый, другой под цвет шкатулки. На крышку наклеивают 2 кружка — белый и цветной, по диаметру равные крышке, а сверху 2 кружка диаметром 70 мм и 2 — по 55 мм. Края цветных круж ков вы резают зубцами (см . рис. 120, в ). Заверш ают украшение маленьким круж очком диаметром 30 мм. Д оны ш ко с двух сторон, а крышку изнутри оклеивают кружками из бересты соответствую щ его диаметра.
Ларец с крышкой (рис. 122) Для плетения потребуются: 20 ленточек длиной 400— 450 мм, шириной 12 мм; 20 ленточек длиной 250— 300 мм, шириной 12 мм для плетения крышки; лента шириной 35— 40 мм для бортика внутри ларца; ленточка другого цвета шириной 12 мм для отделки; 2 пластинки из тонкой жести длиной 360— 380 мм для оправы верха изделия и крышки; ножницы, нож, коточик, ленторез, зажимы, линейка и клей. Имея навыки и опыт в плетении, это изделие можно делать, не применяя шаблона, произвольной формы. 169
Рис. 121. Большая круглая шкатулка
Рис. 122. Ларец с крышкой: О — общий вид; б разметка полотна: в — он рана из жести
Плетение полотна. Делают раскладку 10Х 10 ленточек, проверяют расстояние между горизонтальными и вертикальными точками, закрепляют полотно на углах зажимами. Теперь необходимо наметить углы прямоугольного донышка на стыке 4-й и 5-й ленточек с каждъй стороны полотна (ри с. 122, б ) и прочертить тупым шилом сплошные линии, соединив точки. Плетение стенок. По линиям прогибают полотно, поднимая стенки вверх, заплетают углы и стенки на высоту 3 клеток (см . рис. 96, б ) и закрепляют зажимами. Затем надевают оправу из жести, предварительно придав ей форму, соответствую щ ую размерам донышка, только с овальными углами (ри с. 122, в ). После чего оформляют прямую загибку парными ленточками через оправу (см . рис. 96, г) и заплетают вторым слоем углы, стенки и донышко. Плетение крышки. Д елают раскладку 10Х Ю ленточек. После завершения плетения полотна намечают углы крышки на стыке 4-й и 5-й ленточек с каждой стороны полотна и загибают стенки вверх. Заплетают первым слоем крышку на вы соту 1 клетки. Ч тобы крышка приняла выпуклую форму, ленточки равномерно подтягивают и при этом большими пальцами рук прогибают полотно. На крышку, заплетенную первым слоем, надевают оправу из жести. Затем выполняют прямую загибку через оправу и заплетают крышку вторым слоем. После чего делают небольшой бортик. Для чего ленту крепят клеем с внутренней стороны так, чтобы ее сторона выступала на вы соту 5— 6 мм выше края ларца (см . рис. 122, а). Прежде чем прикрепить крышку, примеряют ее к корпусу и определяют место, где она лучше всего прилегает к стенкам. З десь будет передняя сторона ларца. Затем с противоположной стороны под поперечные ленточки на крышке и корпусе ларца вставляют 4 отрезка берестяных ленточек длиной 50— 60 мм заостренными концами, соединяя их в четырех местах. Для украшения ларца на передней стороне и на крышке (св е р х у ) выплетают по одному цветочку ленточками другого цвета.
Плетение изделий по шаблону Маленький короб (рис. 123, а) Для плетения потребуются: 16 ленточек шириной 17 мм, длиной 450— 500 мм для плетения корпуса; 16 ленточек шириной 17 мм, длиной 300— 350 мм для плетения крышки; ленточки шириной 17 мм для отделки; оправа из жести шириной 6— 7 мм, длиной 450 мм для придания прочности верхней части короба; оправа из жести шириной 172
6 — 7 мм, длиной 450— 500 мм для крышки; деревянная рамка-шаблон (см . рис. 86, а ), ш аблон-доска для крышки (см . рис. 86, б ) ; ножницы, коточик, ленторез, пилка, линейка, зажимы и клей. Выплетают полотно 8 Х 8 ленточек темной стороной внутрь короба. После подготовки полотна и разметки донышка заплетают все четыре угла на вы соту 2 клеток и ставят деревянную рамку-шаблон. Затем заплетают все изделие на вы соту 4 клеток. Причем ленты следует все время уплотнять, чтобы все четыре угла обозначились четко и ровно по шаблону. Высота к о р о б а — 140 мм, квадратное доныш ко — 110Х 1 Ю мм. Закончив первый слой плетения, надевают оправу из жести, предварительно придав ей нуж ную форму (см . рис. 122, в ). Верх изделия завершают прямой загибкой парными ленточками (см . рис. 96, г ). После оформления верха заплетают весь короб вторым,слоем. На стенках выплетают украшение ленточками другого j^веТа, оно будет фиксировать крышку на определенном уровне (ри с. 123, б ) . О т верхнего края короба отступаю т на 1 клетку, продевают ленточку 5 (светлой стороной наруж у) заостренным концом сверху вниз под поперечную 2, протягивают до конца. Затем перекручивают ленточку 5 цветной стороной вверх и пропускают под поперечную 3. О тд е лочную ленточку подтягивают так, чтобы получился первый гори зонтальный угольник (ри с. 123, в ). Снова поворачивают ленточку 5 темной стороной наружу и пропускают ее под поперечную 4 У подтягивают до получения второго угольника в вертикальном направлении (ри с. 123, г ). К онец ленты 5 обрезаю т, а новую цветную вставляют под поперечную 2. Таким сп особом выплетают украшение по периметру изделия. Все угольники должны находиться на одном уровне. Украшение можно выплетать ленточками, совпадающими по цвету с изделием. При работе следят за ровностью, не допускают перетяжек и слабины. Отделочные ленточки вы резают из бересты высокого качества, без трещин, а при работе не допускаю т обры вов. Д ля плетения крышки используют бересту одного цвета с коробом. Заготавливают полотно 8 Х 8 ленточек, размечают доныш ко и ставят доску-ш аблон (см . рис. 86, б ) . Т оч н о по шаблону заплетают крышку на вы соту 2 клеток. Н адевают оправу из жести, оформляю т прямую загибку и заплетают всю крышку вторым слоем. На стенках крышки можно выполнить украшения в виде поясков, разноцветных клеток или горизонтально расположенных угольников.
Портсигар (рис. 124, а) Для плетения потребуются: 10 ленточек шириной 10 мм, длиной 350— 400 мм для плетения полотна; 10 ленточек шириной 10 мм, длиной 200— 250 мм для крышки изделия; берестяные ленточки другого цвета шириной 10 мм для украшения изделия; проволока 175
диаметром 0,12— 0,15 мм или нитки для крепления верха портсигара и крышки; деревянный шаблон (см . рис. 8 4 ); нож, ножницы, коточик, ленторез, зажимы и клей. Выплетают полотно 5 Х 5 ленточек и закрепляют на углах зажимами. Дальнейшее плетение портсигара отличается тем, что работу ве дут по шаблону. При этом на полотне не размечают донышко. Заплетку начинают сразу с одного угла, а потом с противоположного. Для чего на одном из углов поднимают ленточки вверх, заплетают на вы соту 2 клеток и закрепляют зажимами, также заплетают проти воположный угол. Затем ставят деревянный шаблон и начинают вы полнять стенки изделия, натягивая ленточки так, чтобы они плотно облегали шаблон. Первый слой заплетают по шаблону на вы соту 70 мм, или 4 клеток. Тонкой проволокой (ри с. 124, б ) или ниткой в этом месте закрепляют изделие. Верх портсигара оформляю т прямой загибкой парными ленточками и все изделие выплетают вторым слоем. Для изготовления крышки выплетают полотно 5 Х 5 ленточек, накладывают шаблон и с утолщенной стороны делают стенки на вы соту 2 клеток. Затем надевают обруч из тонкой проволоки, закрепляют его прямой загибкой двумя ленточками и заплетают крышку вторым слоем. На стенках крышки можно выполнить украшения в виде поясков или цветных клеток.
Футляр для книги (рис. 125, а) Для плетения потребуются: 24 ленточки односторонней расцветки шириной 12 мм, длиной 550— 600 мм для полотна; ободок из упругой жести шириной 5— 6 мм; шаблон из дерева 170Х 135Х 30 мм или книга соответствую щ его размера; ножницы, нож, ленторез, пилка, зажимы, клей, коточик. С п особ плетения такой же, как при плетении портсигара (п о ш аблону). Ф утл яр предназначен для книги определенного размера: длиной 170 мм, ш ирин ой— 135, толщиной 80 мм. Выплетают полотно 12Х 12 ленточек. После проверки ровности укладки ленточек по горизонтали и вертикали закрепляют углы зажимами. На полотне размечают прямоугольное основание, на котором будут выплетать футляр. Углы его расположены на стыке 2-й и 3-й ленточек с каждой стороны (ри с. 125, б ) . Поднимая вверх, прогибают полотно по намеченным линиям. О собен ность работы заключается в том, что заплетку надо вести одновременно с двух углов. Сначала заплетают на вы соту 2 клеток углы 7 и 2, затем противополож ные углы 3 и 4 и закрепляют зажимами (см . рис. 125, б ) . 176
После чего кладут книгу или деревянный шаблон и начинают последовательно заплетать стенки первым слоем строго по шаблону на вы соту 8 клеток. При этом следят за ровностью натяжки ленточки и не дают распускаться плетению, пользуясь зажимами. Если некоторые ленточки окажутся коротки, добавляют новые того же цвета. Затем надевают ободок из жести и оформляют край одиночными зубцами. Далее определяют середину по длине футляра и выплетают здесь по 3 клетки с обеих сторон прямой загибкой парными лентами (см . рис. 125, а). Остальные 18 пар ленточек заплетают одиночными зубцами. Выполняют второй слой плетения. Торчащ ие концы ленточек аккуратно обрезаю т ножом. Украшение на стенке футляра делают по своему вкусу. М ож но выплести пояски, дорожки, цветы, угольники и др. Например, при плетении второго слоя (заплетка идет сверху вниз) 4— 5 клеток делают темными ленточками, затем обрезаю т их на одном уровне и завершают изделие ленточками другого цвета.
Футляр для очков овальной формы (рис. 126, а) Для плетения потребуются: 24 тонких мягких ленточек шириной 12 мм, длиной 450— 500 мм для корпуса изделия; тонкие ленточки шириной 12 мм другого цвета для украшения; нитки или тонкая проволока для придания прочности изделию; аптекарская резинка для закрепления ленточек на шаблоне; шаблон деревянный (см . рис. 8 5 ); байка или фланель для подкладки; ножницы, нож, коточик, ленторез, зажимы. Ф утл я р можно изготовить разными способами. Для тренировки пальцев предлагается самый трудный вариант, т. к. плётение начинают не с полотна или основания, а с отдельных ленточек по шаблону. Размеры шаблона зависят от размера очков. Д ля плетения первого слоя и создания формы изделия потребую тся 8 ленточек. Л енточку перегибают через носок диаблона светлой стороной наружу, один конец должен проходить сверху слева вдоль кромки шаблона, другой — также вдоль кромки, только с обратной стороны справа. Концы прижимают резинкой (ри с. 126, б ) . В торую ленточку кладут сверху первой, в месте пересечения один конец проходит справа сверху вдоль кромки шаблона, другой слева с обратной стороны , концы ленточек также прижимают резинкой. Эти первые две ленты являются как бы основой в плетении изделия, поэтому от точности размещения их вдоль кромки будет зависеть качество футляра. Затем четырьмя ленточками заплетают носок шаблона и закрепля ют их зажимом посредине (ри с. 126, в ). С другой стороны концы этих 178
Р ис. 126. Ф утляр для очков овальной формы:
д Р ис. 127. Футляр для очков прямоугольной формы
ленточек придерживают пальцами левой руки. Переворачивают шаблон обратной стороной, подтягивают ленточки, заплетают и за крепляют вторым зажимом. Далее остается заплести еще 2 ленточки, после чего продолж ают заплетать все концы по шаблону. Остальные концы ленточек (кром е двух первы х) крепят зажимами. При этом постоянно пальцами уплотняют ленточки. После того, как оплетут носок 8 ленточками, резинку снимают и концами ленточек заплетают шаблон кругом на вы соту 140 мм. В этом месте зажимают плетение для прочности ниткой или надевают ободок из тонкой проволоки. По бокам слева и справа на высоте 130— 140 мм (8 клеток) делают прямую загибку парными ленточками и вплетают концы в корпус изделия (ри с. 126, г ), остальные ленточки заплетают на вы соту 9 клеток, считая от носка изделия. Далее, перекрещивая вверху между собой 2 ленточки, делают прямую загибку (ри с. 126. д ), концы вплетают в корпус изделия. В процессе плетения второго слоя на углах изделия можно повредить ленточку, приподнимая ее коточиком. Ч тобы избежать этого, снимают футляр с шаблона, продевают ленточку, снова надевают на шаблон и продолж ают плести. Выполнять второй слой без шаблона не рекомендуется, иначе изделие потеряет форму. На стенках можно выполнить украшение. Для чего на высоте 4-й и 5-й клеток с обеих сторон выплетают по одному цветочку. Бересту использую т другого цвета, тонкую с гладкой поверхностью. В верхней части изделия на высоте 7-й клетки в горизонтальном направлении выплетают поясок из угольников. По деревянному шаблону выкраивают из байки или фланели подкладку и приклеивают ее внутри футляра для очков.
Футляр для очков прямоугольной формы (рис. 127) Для плетения потребуются: 20 ленточек шириной 10 мм, длиной 450— 500 мм для полотна; 10 ленточек шириной 10 мм, длиной 250— 300 мм для крышки изделия; ленточки из цветного материала для украшения; шаблон деревянный (см . рис. 8 4 ) длиной 130 мм, верх с утолщением на 20— 25 мм; нитки для закрепления корпуса и крышки; нож, ножницы, коточик, ленторез, зажимы. Подготовка материала и плетение. Н арезают 20 ленточек шириной 10 мм, заостряю т концы с обеих сторон, другие 10 заостряю т с одного конца — они нужны для наращивания ленточек в процессе плетения. П олотно 5 X 5 ленточек плетут аналогично полотну для портсигара. К орп ус выполняют на высоту 130 мм, или 8 клеток. В этом месте полотно завязывают ниткой, делают прямую загибку и полностью заплетают корпус вторым слоем, используя для этого ленточки, заостренные с одного конца. 181
К ры ш ку выплетают на вы соту 3 клеток так же, как корпус футляра для очков по утолщенному концу шаблона. Украшение на стенках и крышке делают так же, как на маленьком коробе (см . рис. 123).
Сувенирные лапти (рис. 128, а) Э то одно из самых слож ных по форме и, следовательно, по техническому исполнению изделие. Для плетения потребуются: 16 тонких мягких ленточек одн осто ронней расцветки шириной 12 мм, длиной 600— 650 мм; 4 ленточки шириной 12 мм, длиной 450— 500 мм для плетения двух полотен; ножницы, нож, коточик, ленторез, 8 зажимов. Для плетения каждого лапотка требую тся 8 длинных и 2 короткие ленточки. Сначала берут по 7 длинных. Раскладку делают на столе темной стороной наружу, причем так, чтобы получились два разных лаптя, т. е. левый и правый. В каждую из укладок заплетают по 4 ленточки (ри с. 128, б, в ). О дну из этих укладок на углах закрепляют зажимами, а вторую продолж ают заплетать. В вертикальном направле нии слева вплетают ленточку 5, вверху оставляют конец длиной 150— 160 мм (ри с. 128, г ). В горизонтальном направлении внизу вплетают ленточку 6, конец ее справа также оставляют свободным на 150— 160 мм. Л енточку 7 сгибают пополам (в этом месте будет носок лаптя) и вплетают ее в горизонтальном направлении. Середина ленты 7 должна находиться в верхнем правом углу. Уплотняют плетение и все четыре угла закрепляют зажимами. Таким же образом выплетают вторую заготовку. Плетение первого слоя начинают с носка лаптя так, чтобы темная сторона ленточек была внутри. Правый конец ленточки 7 ставят на ребро вдоль ленточки 2, переплетают его с концами 3, 4, 6 и закрепля ют зажимом. При этом слева и справа оказалось по три конца — их переплетают между собой. Сначала заплетают ленточки 2 и 3 с левой стороны , потом ленточки 4 и / , 5 и 6 и т . д. Ленточки подтягивают так, чтобы образовался плотно сплетенный носок длиной 2 клетки и закрепляют его зажимом (ри с. 128, д ). Затем ленточку 7 перегибают, заплетают параллельно ленточке 6 и закрепляют зажимом, рядом с 7-й заплетают ленты 2 и / и также закрепляют. Д ругой конец ленты 7 перегибают вдоль ленты 5, заплетают его, а затем выплетают здесь ленты 3 и 4 и закрепляют. Таким образом, получились боковые сторонки и подошва лаптя. При этом все ленточки подтягивают, уплотняя плетение, чтобы в нем не бы ло просветов. Далее последню ю длинную ленточку 8 сгибают пополам и ровно по центру ставят ее ребром на носок выше второй клетки (ри с. 128, е ). Обратная сторона ленточки должна бы ть со стороны носка лаптя. 182
д — носок лаптя, закрепленный зажимом; е — начало плетения второго слоя; ж, з — заплетка коротких ленточек сбоку изделия; и, к — плетение второго слоя; / — 10 — ленточки
Ж
Р ис. 128. Сувенирные лапти (продолжение)
Слева и справа от средней отметки находятся по два коротких конца — 2 и 6, 3 и 5. Ими заплетают в обратном направлении по од ной клетке. Э то будет началом плетения второго слоя. Концы ленты 8 вплетают с двух сторон в изделие так, чтобы на подошве они скрестились между собой. Затем, чтобы определить окончательную длину изделия, сверху слева и справа вплетают короткие ленточки 9 и 10, оставляя свободные концы длиной 80— 90 мм в направлении носка, в этом месте их крепят зажимами соответственно к ленточкам 4 и / (ри с. 128, ж, з ) . Т еперь слева и справа со стороны пятки есть по 7 свободны х концов, а со стороны носка через ленточку 8 перегнуты еще 4 ленты. Д ля плетения пятки изделие берут в руки носком влево. Ленту 8 поворачивают в обратном направлении (в сторону носка), заплетают и закрепляют зажимами, затем вплетают ленту 10. Далее также загибают второй конец ленты 8, заплетают его, крепят зажимом и вплетают ленту 9 (или 10) . После чего, используя свободные концы, выплетают пятку на вы соту 2 клеток и закрепляют зажимами. Затем приступают к оформлению верха лаптя. Э то довольно сложная операция, т. к здесь не использую т ободок, оправу или нитку, а ровность края определяют на глаз. П рям ую загибку выполняют парными ленточками, при этом они должны ложиться темной стороной наружу. В зависимости от того, с какой стороны открыта ленточка 7 ( с правой или с левой), получится соответственно правый или левый лапоть. П л е т е н и е л е в о г о л а п т я . Загибку начинают ленточками 9 и 4. При этом конец 9 пройдет по дорож ке ленточки 4, а конец 4 — по дорож ке 9, прижимает их ленточка 8 (ри с. 128, и) . Затем загибают ленту 6 и прижимают ее лентой /0 , далее последовательно кладут: ленту 7 и прижимают лентой 4, 2-ю — 3-й, 1-ю — 7-й, 9 -ю — 5-й, ленту 8 прижимают лентой / , а ленточку 10 заплетают в корпус. Все ленты, которыми прижимают, пропускают под поперечные. Плетение правого лаптя выполняют так ж е : загибку начинают ленточками 7 и /0 , а ленточкой 8 прижимают ленту / , пропуская ее под поперечную (ри с. 128, к ). Затем последовательно кладут и прижимают ленту 5 концом 6, 7— / , 3— 2, 4— 7, 10— 6, 8— 4 , ленту 9 заплетают в корпус. К ром ку выравнивают и выплетают лапти вторым слоем. После завершения плетения проминают лапоть, придают ему нуж ную форму и, самое главное, плоскость подошвы. Вы резают тонкую берестяную ленточку шириной 4— 5 мм, длиной 500— 550 мм, связывают за пятки лапти парой, чтобы подвесить их как украшение. Н осок лаптя можно отделать, вставляя в 2— 3 клетки ленточки другого цвета. Сувенирные лапти можно сделать и маленького размера, используя тонкие ленты. К этой работе целее ообразно приступать только после того, как в совершенстве будет освоена данная технология плетения.
ПЛЕТЕНИЕ КОМ БИ Н И РОВАН Н Ы Х ИЗДЕЛИ Й И З И В О В О ГО П Р У Т А И БЕРЕСТЫ
ж1вовый прут и береста хорош о со четаются между собой в таких изделиях, как хлебницы, конфетницы, подносы, маленькие корзинки и др. Вместо плетеного донышка из ивового прута можно использовать фанерное, оклеенное полотном из берестяных ленточек. После закрепления стоячков изделия заплетают прутьями, а так же лентами из бересты.
Хлебница (рис. 129) Для плетения потребуются: 24 стоячка светлого и 24 темного цвета длиной 450— 500 мм, толщиной 3 мм для плетения стенки в четыре прутика; тонкие длинные прутья для веревочки; пятислойная фанера для донышка; 8 ленточек темного и 8 светлого цвета шириной 10— 12 мм, длиной 200— 250 мм; шаблон-фанера с подставкой; ножницы, нож, коточик, ленторез, пилка, дрель, два шурупа (3 0 — 35 м м ), зажимы и клей. Подготовка материала. И з фанеры выпиливают доныш ко-круж ок диаметром 120 мм, в радиальном направлении просверливают 48 отверстий диаметром 3 мм, причем размечают их по 4 штуки рядом, расстояние между каждым из 4 отверстий — 3 мм, а между четверка 187
ми — 18 мм. В центре плоскости донышка делают отверстие для крепления к подставке шаблона. Выпиливают фанерный кружок диаметром 170 мм и делают круглую подставку высотой 30 мм, диаметром 20— 25 мм. Плетение. Выплетают полотно 8 Х 8 берестяных лент, группируя цветные ленты произвольно по своему вкусу. П олотно наклеивают на фанерное донышко и прижимают грузом до полного высыхания. Затем острым ножом обрезаю т бересту по краю фанерного основания. К шаблону с деревянной подставкой шурупом крепят донышко. В торцевые отверстия плотно, на всю глубину вставляют стоячки. Стоячки подбирают так, чтобы в каждой группе из четырех отверстий было по два белых и цветных стоячка. Проминают их у основания ши лом или круглогубцами. Затем загибают все стоячки вверх, связы вают концы и оплетают стоячки у основания веревочкой в три пру тика. Ч тобы прутья не потеряли гибкость, во время работы их сма чивают влажной тряпкой. Для плетения стенки л ю бую четверку прутьев прогибают дуго образно, обводят четыре прута снаружи, четыре сзади, следующие четыре снаружи и снова четыре сзади, пропускают концы стоячков через веревочку между 5-й и 6-й четверками стоячков. Выравнивают оваль ный загиб прутиков по верхней кромке фанеры-шаблона. Таким обра зом загибают все стоячки. Н из хлебницы оформляют кромкой «коса». После вы сы хания прутья покрывают лаком, стараясь не задеть берестяное д о нышко.
Конфетница (рис. 130) Для плетения потребуются: 53 цветных стоячка длиной 350— 400 мм, диаметром 2 мм для стенок изделия; прутья тонкие (белые и цветные) для плетения ажурных веревочек; прутья для продольных ручек длиной 550 мм, диаметром 3,5— 4 мм; береста светлого и темного цвета для изготовления полотна; фанера пятислойная для донышка и шаблона с подставкой; ножницы, нож, коточик, ленторез, пилка, дрель, 2 шурупа и клей. Подготовка материала. И з фанеры длиной 200 мм, шириной 100 мм выпиливают прямоугольное донышко. Углы делают закругленными. С торцевой стороны просверливают 53 отверстия диаметром 2 мм на расстоянии 10 мм друг от друга для стоячков, 6 отверстий диаметром 3 мм для трех продольных ручек, 2 отверстия в плоскости по центру для крепления донышка на шаблоне. Н арезают 28 берестяных ленточек светлого и 12 темного цвета шириной 10 мм, длиной 300— 350 мм для плетения полотна и ленточки ширинЬй 4— 5 мм для оплетки ручек. П одгоняют комельковые концы прутьев под радиальные отверстия в донышке. 188
Выпиливают фанеру-шаблон длиной 230— 240 мм, шириной 170 мм, 2 деревянные подставки высотой 65— 70 мм. Изготовление донышка. Выплетают берестяное полотно 2 0 X 20 ленточек. Сначала заплетают 8 лент темного, а затем остальные светлого цвета. П олотно необходимо выплетать плотно и ровно, чтобы расстояние между горизонтальными и вертикальными точками было одинаковым. Затем на стыке 7-й и 8-й ленточек с каждой стороны размечают углы. После чего полотно наклеивают на фанерное основание, прижимают грузом до полного высыхания. Высохшее полотно обрезаю т по краю донышка и крепят его к фанерному шаблону с двумя подставками. Вставляют 53 стоячка в торцевые отверстия, затем загибают все стоячки вверх и связы вают концы. Одновременно ставят прутья для 3 продольных ручек: 2 прута цветных и один белый. Плетение стенок. У основания стоячки белыми прутьями закрепля-
Р ис. 130. Конфет ница
ют простой и ажурной веревочкой в два прутика. П овторяю т такое плетение цветными и еще раз белыми прутиками. При работе стоячки выравнивают, концы обрезаю т снаружи. О ставляю т прямой просвет шириной 15 мм. Закрепляют веревочкой в два и один ряд в три прутика. Изделие заканчивают овальным бордюром', его делают высотой 35 мм или выравнивают по кромке фанеры-шаблона. Д ля чего любым стоячком огибают снаружи 4 соседних и вставляют его заостренным концом к 5-му с левой стороны . Ручки крепят, как показано на рисунке 95, и заплетают их берестяными ленточками. После просушки концы ленточки смазывают клеем, а изделие (кром е берестяного доныш ка) покрывают лаком.
Поднос Для плетения потребуются: 65 цветных стоячков длиной 250— 300 мм, диаметром 3— 3,5 мм; тонкие белые прутья для стенок; 4 прута длиной 350— 400 мм, диаметром 40 мм для ручек, береста светлого и темного цвета для основания; фанера толщиной 5— 6 мм для донышка и шаблон; 2 деревянные подставки; нож, ножницы, ленторез, дрель, пилка, отвертка, 8 зажимов, линейка, 4 шурупа (3 0 — 35 мм ) и клей. Подготовка материала. Выпиливают прямоугольное фанерное основание длиной 350 мм, шириной 190 мм. Углы закругляют. С торцевой стороны в радиальном направлении сверлят 60 отверстий диаметром 3— 3,5 мм, глубиной 13— 15 мм, расстояние между отверстиями — 15 мм, 2 отверстия в плоскости для крепления основания К шаблону и по 2 отверстия (на сторонах длиной 190 мм) диаметром 4 мм на расстояние 100 мм друг от друга для ручек. Фанеру-ш аблон делают длиной по центру 400 мм, шириной 280 мм с закругленными углами, просверливают 2 отверстия по центру для крепления деревянных подставок. К роме того, заготавливают 2 под ставки высотой 50 мм, диаметром 20— 25 мм. Н арезаю т 12 берестяных ленточек темного и 64 светлого цвета (или н аоборот) шириной 10 мм, длиной 400— 450 мм. Комельки прутьев подгоняют к Отверстиям в основании. Изготовление донышка. Выплетают полотно 3 8 Х 38 ленточек, сначала использую т 12 ленточек одного цвета, а затем остальные. 64. На полотне размечают прямоугольное донышко, углы которого находятся на стыке 13-й и 14-й ленточек с каждой стороны . Готовое полотно приклеивают к фанерному основанию и ставят под груз. После высыхания полотно обрезаю т по краю фанерного основания и крепят его шурупами к фанере-шаблону с подставками. Плетение стенок. В торцевые отверстия вставляют стоячки и 4 прута для ручек, прогибают их у основания, поднимают вверх и связы вают концы. Затем выплетают ажурную и простую веревочку в два прутика (порядок работы : 1, 2, 1, 2, 1, всего 5 р я д ов). О ставляю т прямой просвет высотой 25 мм и закрепляют стоячки одной ажурной веревочкой. Изделие заканчивают кромкой. К ром ку можно делать ровную по бортику фанеры-шаблона или волнистую. Например, тонкими длинными прутиками выплетают ажурной веревочкой нужный рисунок и по нему делают первую кромку (см . рис. 3 5). Изготовление ручек. Оставш иеся концы стоячков для ручек загибают дугообразно, навстречу друг другу. О бр езаю т с припуском на всю вы соту стенки изделия, застругивают и вставляют в плетение рядом стоячками. Д уж ки оплетают ивовыми или берестяными лентами. Концы прутьев обрезаю т снаружи. После просушки снимают шаблон-фанеру с подставками. П однос покрывают лаком так, чтобы лак не попал на бересту.
Содержание ПЛЕТЕНИЕ ИВОВОГО ПРУТА
3
ПЛЕТЕНИЕ БЕРЕСТЫ
113
История плетения ивового прута Основные породы дикорастущих ив Выращивание ивы Заготовка ивовых прутьев Обработка прутьев, заготовленных в весенне-летний период Обработка прутьев, заготовленных в осенне-зимний период Хранение прутьев Заготовка лент Организация рабочего места Техника безопасности Инструменты, шаблоны и приспособ ления для плетения Подготовка прутьев к плетению Приемы работы ножом Основные виды плетения
3 6
История плетения бересты Заготовка бересты Обработка бересты Хранение бересты Организация рабочего места Инструменты и приспособления Подготовка бересты к плетению Нарезка берестяных лент Плетение полотна Изготовление ободков и ручек Отделка ручек и ободков Плетение изделий из полотна
113 115 117 117 119
Прямое (простое) плетение Простая веревочка в два прутика Веревочка в три прутика
Кромки Ажурное плетение Бордюры Основы изделий Плетение изделий Плетение корзины с обруча Плетение корзины с донышка Корзинка круглая комбини рованная Плетение кашпо по модели Дамская сумочка Корзина хозяйственная Белорусская корзинка Корзинка для цветов Корзинка под бутылку Сухарница Фруктовница с послойным пле тением Ваза конусная Ваза ажурная четырехгранная Ваза конусная с шаровидным основанием Ваза на ножке Хлебница ажурная в один прутик Хлебница ажурная в два прутика Хлебница ажурная в три прутика Фруктовница ажурная Настенное украшение Круглая рамка с бордюром Овальная рамка с бордюром для зеркала Абаж ур Вазочка с двумя ручками Напольная ваза
7
8 10 12 13 13 13 16 16 23 24 24 25 30 31 31 43 43 49 58 58 63 65 67 68 70 70 75 78 82 84 85 88 92 93 95
Маленькая круглая вазочка Конфетница с одиночными зубцами Конфетница двухцветная Вазочка с двойными зубцами Маленькая цветочница Большая цветочница Круглая коробочка Конфетница с двумя ручками Сухарница Конфетница с тремя ручками Большая хлебница Хлебница на ножках Маленькая хлебница Маленькая сухарница Ваза ромбиками Круглая ваза для цветов Солонка на ножках Маленькая солонка Ваза для фруктов Вазочка для печенья
119 123 124 124 127 130 131 131 134 135 137 137 140 142 142 144 146 149 149 151 151 153 155 157 157 160 161
Изготовление изделий из берестя ного пласта
162 162 166 169 169 Плетение изделий по шаблону 172 Маленький короб 172 Портсигар 175 Ф утляр для книги 176 Ф утляр для очков овальной формы 178 Ф утляр для очков прямоуголь ной формы 181 Сувенирные лапти 182
Туески Шкатулка круглая Большая круглая шкатулка Ларец с крышкой
97 97 99 99 102 103 103 107 109
ПЛЕТЕНИЕ КОМБИНИРОВАН НЫХ ИЗДЕЛИЙ ИЗ ИВОВОГО ПРУТА И БЕРЕСТЫ 187 Хлебница Конфетница Поднос
187 188 190
А в т ор этой книги — заслуженный работник культуры Р С Ф С Р , военный дирижер запаса Ф ед ор Ф едорович Трапезников с давних пор увлекается плетением лозы и бересты. Изделия мастера неоднократно экспонировались в выставочных залах общ ества охраны природы и Д етской республиканской библиотеки. Е1го работами любовались в Домах и Д ворцах культуры М осквы и П одмосковья, в редакциях газеты «И звестия» и журнала «К л у б и худож е ственная самодеятельность». М ногочисленные восторж ен ные отзы вы на его произведения были единодушны: «Э то застывшая в плетении музыка». Ф . Ф . Трапезников горячо предан любимому делу. Он не только сам с удовольствием занимается плетением, главное — он увлекает людей своим искусством и щ едро передает им свои знания. У него есть ученики. Н екоторы е из них уже представляли свои работы на выставках. Приглашаем и вас поучиться у Ф едор а Ф едоровича. Желаем успеха в этом интересном деле.
НИВА РОССИИ