Terahertz Spectroscopy Principles and Applications
7525_C000.indd 1
11/15/07 11:29:56 AM
OPTICAL SCIENCE AND ENGINE...
167 downloads
2361 Views
16MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
Terahertz Spectroscopy Principles and Applications
7525_C000.indd 1
11/15/07 11:29:56 AM
OPTICAL SCIENCE AND ENGINEERING Founding Editor Brian J. Thompson University of Rochester Rochester, New York
1. Electron and Ion Microscopy and Microanalysis: Principles and Applications, Lawrence E. Murr 2. Acousto-Optic Signal Processing: Theory and Implementation, edited by Norman J. Berg and John N. Lee 3. Electro-Optic and Acousto-Optic Scanning and Deflection, Milton Gottlieb, Clive L. M. Ireland, and John Martin Ley 4. Single-Mode Fiber Optics: Principles and Applications, Luc B. Jeunhomme 5. Pulse Code Formats for Fiber Optical Data Communication: Basic Principles and Applications, David J. Morris 6. Optical Materials: An Introduction to Selection and Application, Solomon Musikant 7. Infrared Methods for Gaseous Measurements: Theory and Practice, edited by Joda Wormhoudt 8. Laser Beam Scanning: Opto-Mechanical Devices, Systems, and Data Storage Optics, edited by Gerald F. Marshall 9. Opto-Mechanical Systems Design, Paul R. Yoder, Jr. 10. Optical Fiber Splices and Connectors: Theory and Methods, Calvin M. Miller with Stephen C. Mettler and Ian A. White 11. Laser Spectroscopy and Its Applications, edited by Leon J. Radziemski, Richard W. Solarz, and Jeffrey A. Paisner 12. Infrared Optoelectronics: Devices and Applications, William Nunley and J. Scott Bechtel 13. Integrated Optical Circuits and Components: Design and Applications, edited by Lynn D. Hutcheson 14. Handbook of Molecular Lasers, edited by Peter K. Cheo 15. Handbook of Optical Fibers and Cables, Hiroshi Murata 16. Acousto-Optics, Adrian Korpel 17. Procedures in Applied Optics, John Strong 18. Handbook of Solid-State Lasers, edited by Peter K. Cheo 19. Optical Computing: Digital and Symbolic, edited by Raymond Arrathoon 20. Laser Applications in Physical Chemistry, edited by D. K. Evans 21. Laser-Induced Plasmas and Applications, edited by Leon J. Radziemski and David A. Cremers
7525_C000.indd 2
11/15/07 11:29:57 AM
22. Infrared Technology Fundamentals, Irving J. Spiro and Monroe Schlessinger 23. Single-Mode Fiber Optics: Principles and Applications, Second Edition, Revised and Expanded, Luc B. Jeunhomme 24. Image Analysis Applications, edited by Rangachar Kasturi and Mohan M. Trivedi 25. Photoconductivity: Art, Science, and Technology, N. V. Joshi 26. Principles of Optical Circuit Engineering, Mark A. Mentzer 27. Lens Design, Milton Laikin 28. Optical Components, Systems, and Measurement Techniques, Rajpal S. Sirohi and M. P. Kothiyal 29. Electron and Ion Microscopy and Microanalysis: Principles and Applications, Second Edition, Revised and Expanded, Lawrence E. Murr 30. Handbook of Infrared Optical Materials, edited by Paul Klocek 31. Optical Scanning, edited by Gerald F. Marshall 32. Polymers for Lightwave and Integrated Optics: Technology and Applications, edited by Lawrence A. Hornak 33. Electro-Optical Displays, edited by Mohammad A. Karim 34. Mathematical Morphology in Image Processing, edited by Edward R. Dougherty 35. Opto-Mechanical Systems Design: Second Edition, Revised and Expanded, Paul R. Yoder, Jr. 36. Polarized Light: Fundamentals and Applications, Edward Collett 37. Rare Earth Doped Fiber Lasers and Amplifiers, edited by Michel J. F. Digonnet 38. Speckle Metrology, edited by Rajpal S. Sirohi 39. Organic Photoreceptors for Imaging Systems, Paul M. Borsenberger and David S. Weiss 40. Photonic Switching and Interconnects, edited by Abdellatif Marrakchi 41. Design and Fabrication of Acousto-Optic Devices, edited by Akis P. Goutzoulis and Dennis R. Pape 42. Digital Image Processing Methods, edited by Edward R. Dougherty 43. Visual Science and Engineering: Models and Applications, edited by D. H. Kelly 44. Handbook of Lens Design, Daniel Malacara and Zacarias Malacara 45. Photonic Devices and Systems, edited by Robert G. Hunsberger 46. Infrared Technology Fundamentals: Second Edition, Revised and Expanded, edited by Monroe Schlessinger 47. Spatial Light Modulator Technology: Materials, Devices, and Applications, edited by Uzi Efron 48. Lens Design: Second Edition, Revised and Expanded, Milton Laikin 49. Thin Films for Optical Systems, edited by Francoise R. Flory 50. Tunable Laser Applications, edited by F. J. Duarte 51. Acousto-Optic Signal Processing: Theory and Implementation, Second Edition, edited by Norman J. Berg and John M. Pellegrino
7525_C000.indd 3
11/15/07 11:29:57 AM
52. Handbook of Nonlinear Optics, Richard L. Sutherland 53. Handbook of Optical Fibers and Cables: Second Edition, Hiroshi Murata 54. Optical Storage and Retrieval: Memory, Neural Networks, and Fractals, edited by Francis T. S. Yu and Suganda Jutamulia 55. Devices for Optoelectronics, Wallace B. Leigh 56. Practical Design and Production of Optical Thin Films, Ronald R. Willey 57. Acousto-Optics: Second Edition, Adrian Korpel 58. Diffraction Gratings and Applications, Erwin G. Loewen and Evgeny Popov 59. Organic Photoreceptors for Xerography, Paul M. Borsenberger and David S. Weiss 60. Characterization Techniques and Tabulations for Organic Nonlinear Optical Materials, edited by Mark G. Kuzyk and Carl W. Dirk 61. Interferogram Analysis for Optical Testing, Daniel Malacara, Manuel Servin, and Zacarias Malacara 62. Computational Modeling of Vision: The Role of Combination, William R. Uttal, Ramakrishna Kakarala, Spiram Dayanand, Thomas Shepherd, Jagadeesh Kalki, Charles F. Lunskis, Jr., and Ning Liu 63. Microoptics Technology: Fabrication and Applications of Lens Arrays and Devices, Nicholas Borrelli 64. Visual Information Representation, Communication, and Image Processing, edited by Chang Wen Chen and Ya-Qin Zhang 65. Optical Methods of Measurement, Rajpal S. Sirohi and F. S. Chau 66. Integrated Optical Circuits and Components: Design and Applications, edited by Edmond J. Murphy 67. Adaptive Optics Engineering Handbook, edited by Robert K. Tyson 68. Entropy and Information Optics, Francis T. S. Yu 69. Computational Methods for Electromagnetic and Optical Systems, John M. Jarem and Partha P. Banerjee 70. Laser Beam Shaping, Fred M. Dickey and Scott C. Holswade 71. Rare-Earth-Doped Fiber Lasers and Amplifiers: Second Edition, Revised and Expanded, edited by Michel J. F. Digonnet 72. Lens Design: Third Edition, Revised and Expanded, Milton Laikin 73. Handbook of Optical Engineering, edited by Daniel Malacara and Brian J. Thompson 74. Handbook of Imaging Materials: Second Edition, Revised and Expanded, edited by Arthur S. Diamond and David S. Weiss 75. Handbook of Image Quality: Characterization and Prediction, Brian W. Keelan 76. Fiber Optic Sensors, edited by Francis T. S. Yu and Shizhuo Yin 77. Optical Switching/Networking and Computing for Multimedia Systems, edited by Mohsen Guizani and Abdella Battou 78. Image Recognition and Classification: Algorithms, Systems, and Applications, edited by Bahram Javidi
7525_C000.indd 4
11/15/07 11:29:58 AM
79. Practical Design and Production of Optical Thin Films: Second Edition, Revised and Expanded, Ronald R. Willey 80. Ultrafast Lasers: Technology and Applications, edited by Martin E. Fermann, Almantas Galvanauskas, and Gregg Sucha 81. Light Propagation in Periodic Media: Differential Theory and Design, Michel Nevière and Evgeny Popov 82. Handbook of Nonlinear Optics, Second Edition, Revised and Expanded, Richard L. Sutherland 83. Polarized Light: Second Edition, Revised and Expanded, Dennis Goldstein 84. Optical Remote Sensing: Science and Technology, Walter Egan 85. Handbook of Optical Design: Second Edition, Daniel Malacara and Zacarias Malacara 86. Nonlinear Optics: Theory, Numerical Modeling, and Applications, Partha P. Banerjee 87. Semiconductor and Metal Nanocrystals: Synthesis and Electronic and Optical Properties, edited by Victor I. Klimov 88. High-Performance Backbone Network Technology, edited by Naoaki Yamanaka 89. Semiconductor Laser Fundamentals, Toshiaki Suhara 90. Handbook of Optical and Laser Scanning, edited by Gerald F. Marshall 91. Organic Light-Emitting Diodes: Principles, Characteristics, and Processes, Jan Kalinowski 92. Micro-Optomechatronics, Hiroshi Hosaka, Yoshitada Katagiri, Terunao Hirota, and Kiyoshi Itao 93. Microoptics Technology: Second Edition, Nicholas F. Borrelli 94. Organic Electroluminescence, edited by Zakya Kafafi 95. Engineering Thin Films and Nanostructures with Ion Beams, Emile Knystautas 96. Interferogram Analysis for Optical Testing, Second Edition, Daniel Malacara, Manuel Sercin, and Zacarias Malacara 97. Laser Remote Sensing, edited by Takashi Fujii and Tetsuo Fukuchi 98. Passive Micro-Optical Alignment Methods, edited by Robert A. Boudreau and Sharon M. Boudreau 99. Organic Photovoltaics: Mechanism, Materials, and Devices, edited by Sam-Shajing Sun and Niyazi Serdar Saracftci 100. Handbook of Optical Interconnects, edited by Shigeru Kawai 101. GMPLS Technologies: Broadband Backbone Networks and Systems, Naoaki Yamanaka, Kohei Shiomoto, and Eiji Oki 102. Laser Beam Shaping Applications, edited by Fred M. Dickey, Scott C. Holswade and David L. Shealy 103. Electromagnetic Theory and Applications for Photonic Crystals, Kiyotoshi Yasumoto 104. Physics of Optoelectronics, Michael A. Parker 105. Opto-Mechanical Systems Design: Third Edition, Paul R. Yoder, Jr. 106. Color Desktop Printer Technology, edited by Mitchell Rosen and Noboru Ohta 107. Laser Safety Management, Ken Barat
7525_C000.indd 5
11/15/07 11:29:58 AM
108. Optics in Magnetic Multilayers and Nanostructures, Sˇtefan Viˇsˇnovsky’ 109. Optical Inspection of Microsystems, edited by Wolfgang Osten 110. Applied Microphotonics, edited by Wes R. Jamroz, Roman Kruzelecky, and Emile I. Haddad 111. Organic Light-Emitting Materials and Devices, edited by Zhigang Li and Hong Meng 112. Silicon Nanoelectronics, edited by Shunri Oda and David Ferry 113. Image Sensors and Signal Processor for Digital Still Cameras, Junichi Nakamura 114. Encyclopedic Handbook of Integrated Circuits, edited by Kenichi Iga and Yasuo Kokubun 115. Quantum Communications and Cryptography, edited by Alexander V. Sergienko 116. Optical Code Division Multiple Access: Fundamentals and Applications, edited by Paul R. Prucnal 117. Polymer Fiber Optics: Materials, Physics, and Applications, Mark G. Kuzyk 118. Smart Biosensor Technology, edited by George K. Knopf and Amarjeet S. Bassi 119. Solid-State Lasers and Applications, edited by Alphan Sennaroglu 120. Optical Waveguides: From Theory to Applied Technologies, edited by Maria L. Calvo and Vasudevan Lakshiminarayanan 121. Gas Lasers, edited by Masamori Endo and Robert F. Walker 122. Lens Design, Fourth Edition, Milton Laikin 123. Photonics: Principles and Practices, Abdul Al-Azzawi 124. Microwave Photonics, edited by Chi H. Lee 125. Physical Properties and Data of Optical Materials, Moriaki Wakaki, Keiei Kudo, and Takehisa Shibuya 126. Microlithography: Science and Technology, Second Edition, edited by Kazuaki Suzuki and Bruce W. Smith 127. Coarse Wavelength Division Multiplexing: Technologies and Applications, edited by Hans Joerg Thiele and Marcus Nebeling 128. Organic Field-Effect Transistors, Zhenan Bao and Jason Locklin 129. Smart CMOS Image Sensors and Applications, Jun Ohta 130. Photonic Signal Processing: Techniques and Applications, Le Nguyen Binh 131. Terahertz Spectroscopy: Principles and Applications, edited by Susan L. Dexheimer
7525_C000.indd 6
11/15/07 11:29:59 AM
Terahertz Spectroscopy Principles and Applications
Edited by
Susan L. Dexheimer
Boca Raton London New York
CRC Press is an imprint of the Taylor & Francis Group, an informa business
7525_C000.indd 7
11/15/07 11:29:59 AM
CRC Press Taylor & Francis Group 6000 Broken Sound Parkway NW, Suite 300 Boca Raton, FL 33487‑2742 © 2008 by Taylor & Francis Group, LLC CRC Press is an imprint of Taylor & Francis Group, an Informa business No claim to original U.S. Government works Printed in the United States of America on acid‑free paper 10 9 8 7 6 5 4 3 2 1 International Standard Book Number‑13: 978‑0‑8493‑7525‑5 (Hardcover) This book contains information obtained from authentic and highly regarded sources. Reprinted material is quoted with permission, and sources are indicated. A wide variety of references are listed. Reasonable efforts have been made to publish reliable data and information, but the author and the publisher cannot assume responsibility for the validity of all materials or for the conse‑ quences of their use. Except as permitted under U.S. Copyright Law, no part of this book may be reprinted, reproduced, transmitted, or utilized in any form by any electronic, mechanical, or other means, now known or hereafter invented, including photocopying, microfilming, and recording, or in any information storage or retrieval system, without written permission from the publishers. For permission to photocopy or use material electronically from this work, please access www. copyright.com (http://www.copyright.com/) or contact the Copyright Clearance Center, Inc. (CCC) 222 Rosewood Drive, Danvers, MA 01923, 978‑750‑8400. CCC is a not‑for‑profit organization that provides licenses and registration for a variety of users. For organizations that have been granted a photocopy license by the CCC, a separate system of payment has been arranged. Trademark Notice: Product or corporate names may be trademarks or registered trademarks, and are used only for identification and explanation without intent to infringe. Library of Congress Cataloging‑in‑Publication Data Dexheimer, Susan L. Terahertz spectroscopy : principles and applications / Susan L. Dexheimer. p. cm. ‑‑ (Optical science and engineering) Includes bibliographical references and index. ISBN 978‑0‑8493‑7525‑5 (hardcover : alk. paper) 1. Terahertz spectroscopy. I. Title. II. Series. QC454.T47D49 2007 543’.5‑‑dc22
2007024954
Visit the Taylor & Francis Web site at http://www.taylorandfrancis.com and the CRC Press Web site at http://www.crcpress.com
7525_C000.indd 8
11/15/07 11:30:00 AM
Contents Preface.......................................................................................................................xi Editor..................................................................................................................... xiii Contributors............................................................................................................ xv
Section I Instrumentation and Methods Chapter 1 Terahertz Time-Domain Spectroscopy with Photoconductive Antennas..................1 R. Alan Cheville Chapter 2 Nonlinear Optical Techniques for Terahertz Pulse Generation. and Detection — Optical Rectification and Electrooptic Sampling......................... 41 Ingrid Wilke and Suranjana Sengupta Chapter 3 Time-Resolved Terahertz Spectroscopy and Terahertz Emission. Spectroscopy............................................................................................................. 73 Jason B. Baxter and Charles A. Schmuttenmaer
Section II A pplications in Physics and Materials Science Chapter 4 Time-Resolved Terahertz Studies of Carrier Dynamics in Semiconductors, Superconductors, and Strongly Correlated Electron Materials.............................. 119 Robert A. Kaindl and Richard D. Averitt Chapter 5 Time-Resolved Terahertz Studies of Conductivity Processes. in Novel Electronic Materials................................................................................. 171 Jie Shan and Susan L. Dexheimer
7525_C000.indd 9
11/15/07 11:30:01 AM
Chapter 6 Optical Response of Semiconductor Nanostructures in Terahertz Fields. Generated by Electrostatic Free-Electron Lasers...................................................205 Sam G. Carter, John Cerne and Mark S. Sherwin
Section III A pplications in Chemistry and Biomedicine Chapter 7 Terahertz Spectroscopy of Biomolecules............................................................... 269 Edwin J. Heilweil and David F. Plusquellic Chapter 8 Pharmaceutical and Security Applications of Terahertz Spectroscopy................. 299 J. Axel Zeitler, Thomas Rades and Philip F. Taday Index....................................................................................................................... 325
7525_C000.indd 10
11/15/07 11:30:01 AM
Preface The development of new sources and methods in the terahertz, or far-infrared, spectral range has generated intense interest in terahertz spectroscopy and its application in a wide range of fields. Terahertz frequencies, broadly defined as 0.1–30 THz, span the range of low-energy excitations in electronic materials, low-frequency vibrational modes of condensed phase media, and vibrational and rotational transitions in molecules, making this a key spectral range for probing fundamental physical interactions as well as for practical applications. Moreover, the short pulse durations achievable with terahertz techniques based on femtosecond laser sources allow timeresolved measurements on femtosecond timescales, which were previously inaccessible in this spectral range. This volume provides an up-to-date reference on state-of-the-art terahertz spectroscopic techniques, focusing in particular on time-domain methods based on femtosecond laser sources, and reviewing important recent applications of terahertz spectroscopy in physics, chemistry, and biology. Chapters are contributed by leading experts in each topic. The focus of this book specifically on spectroscopy and the range of applications presented set it apart from the few other recent volumes in the emerging terahertz field. The reader is referred to Sensing with Terahertz Radiation edited by Daniel Mittleman (Springer, 2003) and to Terahertz Sensing Technology edited by Dwight L. Woolard et al. (World Scientific, 2003) for applications including ranging and imaging, and Terahertz Optoelectronics edited by Kiyomi Sakai (Springer, 2005) for a review focusing specifically on work on generation of terahertz radiation carried out in Japan. The first section of this book is devoted to instrumentation and methods for time-domain and time-resolved terahertz spectroscopy. The first chapter provides a comprehensive discussion of time-domain terahertz spectroscopic measurements using photoconductive antenna sources and detectors, including methods for determining optical constants from time-domain measurements. The second chapter provides a review of time-domain terahertz techniques based on the nonlinear optical processes of optical rectification for terahertz pulse generation and free-space electrooptic sampling for terahertz pulse detection, and the third chapter reviews current state-of-the-art femtosecond time-resolved techniques and terahertz emission spectroscopy using femtosecond laser sources. Measurements using free electron laser sources and the established far-infrared frequency-domain spectroscopic techniques of FTIR and photomixing are also discussed in the context of specific applications in Sections II and III. Applications of terahertz spectroscopy to key areas of current interest, both fundamental and applied, are presented in Sections II and III of the book. The second section is devoted to applications in physics and materials science, including studies of carrier processes in state-of-the-art semiconductor materials, superconductors, novel
7525_C000.indd 11
11/15/07 11:30:01 AM
electronic materials, and semiconductor nanostructures. The third and final section of the book is devoted to applications of terahertz spectroscopy to the biological and chemical fields. This first chapter of this section reviews studies of biologically important molecules, and the final chapter reviews applications of terahertz spectroscopy to pharmaceutical analysis and to the detection of security hazards. Susan L. Dexheimer Editor
7525_C000.indd 12
11/15/07 11:30:02 AM
Editor Susan L. Dexheimer received an S.B. degree in Physics from the Massachusetts Institute of Technology and a Ph.D. in Physics from the University of California, Berkeley. She has a broad research background at the interfaces of experimental condensed matter physics, chemical physics, and molecular biophysics. She is currently on the faculty at Washington State University, where her research includes the application of femtosecond optical and terahertz spectroscopic techniques to study ultrafast dynamics in electronic materials and molecular systems.
7525_C000.indd 13
11/15/07 11:30:02 AM
7525_C000.indd 14
11/15/07 11:30:02 AM
Contributors Richard D. Averitt Department of Physics Boston University Boston, Massachusetts Jason B. Baxter Department of Chemistry Yale University New Haven, Connecticut Sam G. Carter JILA University of Colorado Boulder, Colorado John Cerne Department of Physics State University of New York at Buffalo Buffalo, New York R. Alan Cheville Department of Electrical and. Computer Engineering Oklahoma State University Stillwater, Oklahoma Susan L. Dexheimer Department of Physics Washington State University Pullman, Washington Edwin J. Heilweil National Institute of Standards. and Technology Gaithersburg, Maryland
7525_C000.indd 15
Robert A. Kaindl Lawrence Berkeley National. Laboratory Berkeley, California David F. Plusquellic National Institute of Standards. and Technology Gaithersburg, Maryland Thomas Rades School of Pharmacy University of Otago Dunedin, New Zealand Charles A. Schmuttenmaer Department of Chemistry Yale University New Haven, Connecticut Suranjana Sengupta Department of Physics, Applied. Physics and Astronomy Rensselaer Polytechnic Institute Troy, New York Jie Shan Department of Physics Case Western Reserve University Cleveland, Ohio Mark S. Sherwin Department of Physics University of California, Santa Barbara Santa Barbara, California Philip F. Taday TeraView Ltd. Cambridge, United Kingdom
11/15/07 11:30:03 AM
Ingrid Wilke Department of Physics, Applied. Physics and Astronomy Rensselaer Polytechnic Institute Troy, New York
7525_C000.indd 16
J. Axel Zeitler Department of Chemical. Engineering University of Cambridge Cambridge, United Kingdom
11/15/07 11:30:03 AM
Section I Instrumentation and Methods
7525_S001.indd 1
11/8/07 2:26:50 PM
7525_S001.indd 2
11/8/07 2:26:50 PM
1
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas R. Alan Cheville Oklahoma State University
Contents 1.1 Introduction to Terahertz Spectral Region........................................................1 1.2 Brief Theoretical Background for Photoconductive Terahertz Generation.........3 1.3 Terahertz-Generation Process........................................................................... 6 1.4 Detecting Terahertz Radiation Using Photoconductive Antennas.................. 10 1.5 Experimental Considerations of Terahertz Spectroscopy............................... 19 1.6 Terahertz Beam Propagation and Optical Systems.........................................24 1.7 Adaptations and Extensions of Terahertz Spectroscopy Systems................... 30 References................................................................................................................. 37
1.1 Introduction to TerahertZ Spectral Region A recent report from the National Academies outlines that electronic and optics are combining to open up a new “Tera-Era.”1 This vision includes computers performing operations at rates of teraflops, terabit-per-second communication systems, and electronic devices on the picosecond time scale. From a spectroscopic point of view, the terahertz (THz) spectral region from 300 GHz (λ = 1 mm) to 10 THz (λ = 30 µm) has not yet seen the technological development of optical or microwave frequencies with the result that commercial spectrometers covering the entire spectral range are not yet widely available. This is primarily because of the difficulty of generating and detecting THz frequencies compared with the better-established technologies of optics and electronics. The so-called “THz gap” arises from the nature of the sources and detectors used in spectroscopy both at the optical (high-frequency) side and electronic (lowfrequency) side of the gap. One terahertz corresponds to a photon energy of 4 meV (33.3 cm–1). These energies are much less than the electronic state transitions of
7525_C001.indd 1
11/19/07 10:58:38 AM
Terahertz Spectroscopy: Principles and Applications Wavelength (m) 10
0
10–2
10–1
10–3
+
1010
10–5
10–6
10–7
300 K
– – Rotational Transitions
109
10–4
+
– – Vibrational Transitions 1011
1012
1013
Electronic Transitions 1014
1015
1016
Frequency (Hz)
Figure 1.1 The electromagnetic spectrum from microwave to optical region. The area easily accessible by THz spectroscopy using photoconductive sources is shown shaded in gray. Rotational, vibrational, and electronic transitions are shown along with the blackbody radiation curve at 300 K.
atoms and molecules commonly used in lasers or other light sources (Figure 1.1). Semiconductor materials also have bandgaps on the order of an electron volt, orders of magnitude larger than THz energies. Vibrational frequencies, such as the 10.6 µm CO2 laser, and rotational transition frequencies do fall in the far infrared. Light sources based on these transitions exist, but typically cover limited frequency ranges.2 Thermal emission from incoherent blackbody radiation is one of the most commonly used sources since the thermal energy, kT, is about 25 meV at room temperature (300 K). The blackbody radiation curve and the relative spectral power emitted are shown as a black line in Figure 1.1. Scaling electronics to operate in the THz gap is limited by the frequency response of devices. The high-frequency limit is determined by the time it takes electrons to traverse the device, which is determined by the physical size and carrier mobility. Although feature sizes are continually shrinking, material properties ultimately limit high-frequency response. New semiconductor materials and the ability to confine carriers at the quantum level are leading to high-speed devices pushing into the THz gap. Some exciting recent developments are laser diodes,3 high electron mobility transistors, and quantum cascade lasers.4 The same physical limitations that arise in scaling optical sources down (or electronic sources up) to the THz spectral region also hold for detectors of THz radiation. THz photons cannot excite electrons into the conduction band in a photodiode (without multiphoton absorption, which would require unreasonable intensities) or provide enough energy to cause photoelectric emission of electrons. Although bolometers can detect radiation, they are limited by incoherent thermal background signals unless cooled to very low temperatures. The far infrared spectrum and the points made previously are summarized in Figure 1.1. There is a great deal of interest in this spectral region ranging from creating faster electronic devices to the wealth of spectroscopic information available.
7525_C001.indd 2
11/19/07 10:58:39 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
THz spectroscopy provides information on the basic structure of molecules and is a useful tool of radio astronomy. Rotational frequencies of light molecules fall in this spectral region, as do vibrational modes of large molecules with many functional groupings, including many biologic molecules that have broad resonances at THz frequencies. This chapter provides an overview of how the technologic difficulties inherent to THz generation and detection can be overcome through a synthesis of ultrafast optical and electronic techniques. By gating micron scale antennas on photoconductive substrates with femtosecond pulses, it is possible to generate and detect electromagnetic pulses with THz bandwidths.
1.2 Brief Theoretical Background for Photoconductive TerahertZ Generation Because THz radiation generated and detected through photoconduction arises from the flow of charge, it is theoretically described by Maxwell’s equations. Maxwell’s equations do not, however, describe the processes from which charge flow occurs on a femtosecond scale in semiconductors. This is a topic worthy of a complete book,5 and the description of processes from which charge flow arises are not gone into in detail here. From the perspective of THz generation, the source terms of Maxwell’s equations are written to show time-dependent terms explicitly by adding a (t) to them. ∂m (t )H (t ) ∇ × E (t ) = ∂t
∂e (t )E (t ) ∇ × H (t ) = s (t )E (t ) + ∂t
(1.1)
Here, m(t)H(t) = B(t) is the magnetic flux, H(t)= s(t)E(t) is the current density, and e(t)E(t) = D(t) is the electric displacement. Any process that creates a time-dependent change in the material properties m, s, or e can act as a source term that can result in emission of THz radiation. For THz generation using photoconductive switches, an ultrashort optical pulse incident on a semiconductor causes rapid transient changes to the macroscopic material properties represented by s(t), m(t), and e(t). For the discussion that follows, the major change caused by the optical pulse is assumed to be in the conductivity, s. The rapid, optically induced change of s on a femtosecond time scale is the origin of ultrafast THz pulses generated through photoconduction as well as the physical mechanism by which the THz pulses are detected. It is important to note that many physical processes occur when ultrafast optical pulses are absorbed by semiconductors, and, from an experimental viewpoint, they are not easily separable. Both resonant (absorption of a photon to create charge carriers, s) and nonresonant (nonlinear optical difference frequency generation, e) effects can contribute to THz pulse generation. A common example of a material in which both processes contribute to THz generation is gallium arsenide (GaAs). The driving term, s(t), in Maxwell’s equations results from an ultrafast optical pulse that impulsively excites the semiconductor. The resulting electric and magnetic
7525_C001.indd 3
11/19/07 10:58:41 AM
Terahertz Spectroscopy: Principles and Applications
Electric Field
1
0
–1 –2
–1
0 Time (ps)
1
2
Spectral Amplitude
1
0 0.1
1.0
10 Frequency (THz)
100
Figure 1.2 Electric field of a measured THz pulse and the simulated field of the exciting optical pulse are shown in the upper figure, whereas the amplitude spectrum is shown in the lower figure.
fields created through the time-dependent conductivity have fast transients with correspondingly broad spectral bandwidths. The spectral bandwidth can be estimated from the uncertain relation [between the bandwidth, Dw, required to support a transient signal] Dt. Because DtDw ≥ ½, a 1-ps excitation pulse requires, and can create, spectral bandwidths on the order of 0.3 THz, whereas a 100-fs transient has a bandwidth of at least 3 THz. With sub-10-fs pulses readily available from current commercial ultrafast lasers, very broad spectral coverage of the THz region has been achieved. An example of a THz measurement from the author’s laboratory is shown in Figure 1.2. The upper figure compares the measurement of the electric field of a THz pulse in the time domain with the numerically calculated electric field of the 50-fs optical pulse at 800 nm used to generate the THz pulse. The rapidly oscillating carrier frequency of the optical pulse makes it appear to be a filled Gaussian envelope. The spectral amplitude of the THz pulse and optical pulse are shown in the lower figure. Although the actual bandwidth of the optical pulse (10.6 THz) is considerably larger than that of the THz pulse (0.7 THz), the THz pulse spans a greater fraction of the electromagnetic spectrum in terms of Dn/no: 0.7 for the THz pulse compared to 0.003 for the optical pulse. Recent developments in THz generation and detection
7525_C001.indd 4
11/19/07 10:58:43 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
have extended the frequency range spanned by THz pulses by an additional order of magnitude or more. One of the great advantages of ultrafast THz measurements is that this bandwidth allows a broad range of energy scales (frequencies) to be probed in a single measurement with high temporal resolution. Figure 1.2 highlights some of the differences between short pulses in the THz and optical spectral regions. The electric field of the THz pulse is a nearly single cycle oscillation, whereas the optical pulse is described as a Gaussian pulse envelope superimposed on a sinusoidal carrier frequency. The optical pulse thus meets the slowly varying envelope approximation, whereas the THz pulse does not. Thus many of the simplifying assumptions used in quantum and nonlinear optics do not necessarily apply to THz systems.6,7 From a theoretical perspective, an accurate description of the pulse propagation requires the solution of the coupled Maxwell-Bloch equations. Because THz pulses used for spectroscopy have very low peak powers compared with optical pulses, nonlinearities can generally be neglected and propagation is treated using linear dispersion theory.8 Perhaps the most significant difference between THz pulses and visible, infrared, or ultraviolet light more familiar to most researchers is THz spectroscopy directly measures the electric field of the pulse rather than the intensity. The direct measurement of field is possible simply because of the much slower variation of the field as can be seen in Figure 1.2. Intensity, I, and electric field, E, are related by:
I=
1 m EE * 2 e
(1.2)
Equation 1.2 illustrates the well-known fact that intensity measurements contain no phase information unless techniques such as holography or interferometry are used to measure phase relative to another optical beam. The time-resolved electric field of the THz pulse does, however, contain complete phase information that can be extracted directly from THz measurements. For the more familiar intensity measurements, energy conservation dictates that reflection and transmission coefficients are real and positive with magnitude less than one in almost all commonly encountered cases. Because THz experiments measure the electric field amplitude the Fresnel coefficients can be complex and have values less than zero or greater than one. For example, the amplitude transmission coefficient from air to silicon is t12 = 0.45, whereas that from silicon to air is t21 = 1.55. Examples will be discussed later. The final commonly encountered difference between experimental measurements at optical and THz frequencies is the effect of phase shifts on the measured pulse shape. Small changes in the phase of an optical pulse generally have little to no effect on the measured pulse shape. Larger frequency-dependent phase shifts, such as those caused by dispersive media, do result in pulse broadening. In contrast, small-frequency, independent-phase changes result in significant reshaping of THz pulses, as shown in Figure 1.3. Numeric phase changes of 0, p/16, p/8, p/4, p/2, and p result in pulse reshaping up to a complete inversion of the pulse. Such phase shifts can occur on reflection,9 when the pulse propagates through a caustic,10 or in propagating through materials with a complex index.
7525_C001.indd 5
11/19/07 10:58:45 AM
Terahertz Spectroscopy: Principles and Applications
π
0π
π/16
π/8
π/4 π/2
Figure 1.3 Effect of frequency-independent phase shifts from 0 to π/2 radians on the Terahertz pulse shape.
1.3 TerahertZ-Generation Process Generation and detection of THz pulses occur through nonlinear interaction of the driving optical pulse with a material with fast response. There are two major classifications, of which only one, photoconductivity, is discussed in this chapter. Photoconductive THz generation occurs when optical excitation induces conductivity changes in a semiconductor. This is a resonant interaction and the photons are absorbed through interband transitions. The second mechanism is nonresonant interaction arising from nonlinear frequency mixing or optical rectification. Transient photoconductivity is used for both the generation and detection of THz radiation, with THz generation discussed first. A simplified representation of the process of photoconductive THz generation is illustrated in Figure 1.4. The six frames of Figure 1.4 represent different steps in pulse generation and are discussed below. A great deal of research continues to be done on understanding the physics underlying THz pulse generation from transient photoconductivity. This area is highly multidisciplinary, integrating knowledge of optical generation of hot carriers, their subsequent rapid thermalization, ballistic transport on a femtosecond time scale, rapid screening of generated fields, design of high bandwidth antenna structures, and propagation of single cycle pulses in dispersive media. Because this chapter focuses primarily on using the pulses in spectroscopic application, only the basic physical fundamentals of THz generation are discussed.11 The geometry of a basic photoconductive THz source is shown in a top-down view in Figure 1.4a. A coplanar transmission line is fabricated on a semiconductor substrate with high mobility, m, usually GaAs or low temperature-grown GaAs.
7525_C001.indd 6
11/19/07 10:58:46 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
EDC EDC
– –– – –
–
(a)
t = 0++
(d) EDC
J(t)
–+ –+ –+ +– +– +–
t=0
ETHz(t)
t>0
(b)
(e) EDC
–
+
P(t)
t<0
N(t)
+ + +++
– – – ++ + + + – –
–
+
J(t)
(c)
EDC
t=
0+
N(t)
–
–
0
+ –
–+
+
+
+
t >> 0 (f)
Figure 1.4 Illustration of the process of photoconductive Terahertz generation. Frame (a) shows the coplanar transmission lines before excitation. In (b), the optical pulse generates charge carriers which are accelerated in the static field (c), and create an opposing field in the semiconductor (d). The induced polarization creates a transient current element which radiates a Terahertz pulse (e) followed by recombination back to steady state (f).
Because the mobility gives the ratio of carrier drift velocity to applied electric field, carriers in high-mobility compounds accelerate rapidly, leading to fast rise times. The coplanar transmission lines are DC-biased to produce a field on the order of 106 V/m near the breakdown threshold for air. The electric field near the surface of the semiconductor is represented in the figure by parallel arrows between the lines. Energy is stored by this capacitive structure, with a capacitance on the order of several pF. The semiconductor used has a high dark resistivity to minimize current flow and the resultant local heating and device failure due to electromigration.12 The first step in generating THz radiation is optical excitation of the region of high electric field. It is important that the semiconductor bandgap energy, Egap, is less than the photon energy, hν, so that electron-hole pairs are formed. Carrier generation is shown in a cross-sectional view in Figure 1.4b, where dimensions are shown not to scale to better illustrate the physical processes occurring. A focused ultrafast optical pulse incident between the metal lines generates a thin conductive region down to approximately the absorption depth 1/α. Typical absorption coefficients of semiconductors above the band gap range from α = 103 cm–1 to α = 105 cm–1. The optically generated electron-hole pairs form an electrically neutral plasma near the semiconductor surface as illustrated in Figure 1.4b. The time evolution of the charge
7525_C001.indd 7
11/19/07 10:58:48 AM
Terahertz Spectroscopy: Principles and Applications
density is given by N(t) with the total carrier density the sum of that of the electrons and holes: N(t) = Ne(t) + Nh(t). At low-excitation fluences, the charge density is proportional to the intensity profile of the optical pulse I(t). The time evolution of the carrier density is given by:11
N (t ) =
∫
t
0
G (t)δt − N 0e
−
t tc
(1.3)
where the first term describes N(t) at time scales of the laser pulse and the second describes the evolution of the carrier density at longer times. Here tc is the carrier lifetime, G(t) is the optical carrier generation rate determined by the optical pulse profile, and No is the total number of carriers generated. The free carriers affect the conductivity by s(t) = N(t)em. The current density is J(t) = s(t)E, which can be written as J(t) = N(t)ev(t) with v(t) the carrier velocity. Immediately after generation of the carriers in the semiconductor the accelerating field is E(t = 0+) = EDC. The time dependence has been written explicitly to illustrate the transient nature of the photoconductivity on subpicosecond time scales. It is the transient current, J(t), that generates the THz pulse. The carriers are accelerated in the applied electric field, EDC, as shown in Figure 1.4c. The time evolution of carrier velocity is determined by the initial acceleration of carriers with effective mass m* and by rapid carrier scattering with a characteristic time ts: δv (t ) v (t ) e =− + E (t ) δt ts m* The carrier scattering time is determined by phonon scattering, carrier scattering, scattering from dopants, and the photon energy, or where in the conduction band carriers are generated. The spatial separation of the photo-induced electron and hole plasma create a macroscopic polarization, P(t), in the semiconductor, shown in Figure 1.4d. The polarization is given by P(t) = N(t)er(t), where r(t) is the spatial separation of charges. The time evolution of the induced polarization is calculated from:
δP (t ) P (t ) =− + N (t )ev (t ) δt tR
(1.4)
where the time derivative of the polarization is N(t)ev(t). As shown in Figure 1.4d, the induced polarization creates an electric field that opposes the static field of the biased coplanar stripline. The electric field responsible for carrier acceleration then evolves as:
E (t ) = E DC +
7525_C001.indd 8
P (t ) eg
(1.5)
11/19/07 10:58:52 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
where g is a numerical factor that depends on the geometry. The four coupled differential equations describing the carrier density N(t), the velocity v(t), the polarization P(t), and the electric field seen by the carriers E(t) describe the time evolution of the current created by photo-excitation of a carrier.11 The THz pulse is generated from the transient current element, J(t), shown in Figure 1.4e on a greatly expanded spatial scale. Generation of a pulse follows directly from Maxwell’s equations because time varying current serves as a source term:
∂H THz (t ) ∇ × ETHz (t ) = − m ∂t ∂e((t )ETHz (t ) ∇ × H THz (t ) = J (t ) + ∂t
(1.6)
where the subscript THz distinguishes the time resolved THz field from the field in the semiconductor. Maxwell’s equations with these terms and those described in the next paragraphs are generally not amenable to analytic solution. Because many experimental techniques of THz generation focus the optical spot to micron diameters to generate large carrier densities, the current element is typically much smaller than one wavelength of the generated THz radiation and thus can be described as a Hertzian dipole.13 The calculations are complicated by the fact that the current element is on the surface of a dielectric half space, but both analytic and numerical solutions exist for dipole antennas on dielectric half spaces.14 The major fraction of the laser-generated burst of THz radiation is emitted into the semiconductor by a factor proportional to n3 where n is the index of refraction of the semiconductor. Because most semiconductors have refractive indices higher than three at THz frequencies, this is a significant enhancement in directivity and aids in collection and collimation of the THz radiation. When the optical excitation spot is not tightly focused so the current distribution is on the same order of a wavelength or larger, the problem is often treated as a summation (array) of small radiating elements. Because the current rises and falls on a time scale of one picosecond, it generates a well-defined pulse front that propagates outward from the optical excitation point. The radiation pattern is changed by the proximity of the dipole to the air–semiconductor interface and will be discussed later. All these processes happen on time scales of picoseconds or less. On longer time scales, carrier recombination within the semiconductor or at the metal electrodes causes the induced polarization to decay and the static bias electric field to reestablish itself, This is illustrated in Figure 1.4f. The recovery of the semiconductor to the state shown in Figure 1.4a typically takes hundreds of picoseconds or longer.11 In summary, a DC-biased semiconductor (a) has an electron-hole plasma created on femtosecond time scales by an optical pulse (b). The rapid acceleration and separation of the electrons and holes create a current transient (c). The macroscopic polarization creates an opposing field that screens the DC field (d). The transient electric field determined (approximately) by the time derivative of the current results in a radiated pulse front (e). In times of hundreds of picoseconds, the semiconductor recovers (f).
7525_C001.indd 9
11/19/07 10:58:54 AM
10
Terahertz Spectroscopy: Principles and Applications
Considerable research has gone into development of photoconductive THz emitters for specific applications. The simple coplanar stripline structure of Figure 1.4 can be replaced by an array of antenna structures. Log-spiral, bowtie, and a variety of dipole structures have all been developed. In this case, the photocurrent provides an impulse excitation to the antenna and the radiation pattern and THz pulse are determined both by the response of the semiconductor as well as the antenna. Biased antenna structures are not required to generate photoconductive THz radiation. The electric field that arises from depletion of carriers from recombination centers near the surface will accelerate photo-induced carriers away from or toward the surface. In this case, the induced electric dipole is normal to the surface, rather than in the plane of the surface as with antenna structures, which makes it more difficult to couple radiation out of the substrate. The photo-Dember effect15 can also give rise to THz radiation. The Dember effect arises from the difference in mobility between electrons and holes, which causes the carriers accelerate at different rates.
1.4 Detecting TerahertZ Radiation Using Photoconductive Antennas Detecting THz pulses using photoconductively gated antennas relies on the same physical principles as generation of THz pulses, namely ultrafast pulse excitation in a semiconductor causing rapid changes in conductivity. To detect THz pulses with subpicosecond resolution, a micron-scale dipole antenna is fabricated on a semiconductor substrate with a very short carrier lifetime of 1 ps or less. Both the antenna design and properties of the semiconductor critically affect THz detection. A typical antenna structure is shown in Figure 1.5d from a top-down view. The antenna is a center-excited dipole fabricated between coplanar strip lines with length, h, of 10 to 200 µm. The length is the most critical element of the antenna and will be discussed later. The antenna’s width is tens of microns with a center gap of less than ten microns corresponding to approximately the diameter of the focused gating laser pulse. Typical dark resistance (no optical excitation) of these antenna structures is on the order of megaohms and depends on the substrate resistivity and antenna and coplanar stripline dimensions. The photoconductive detection process is illustrated schematically in Figure 1.5a–c. Figure 1.5a is a side-on view that illustrates the ultrafast laser pulse (not to scale, see Figure 1.2) incident from the left on the antenna of Figure 1.5d. A THz pulse is propagating from the right, but has not yet arrived at the antenna structure. As in generation of THz pulses, the ultrafast laser pulse generates an electron and hole plasma which decreases conductivity of the antenna gap. The time resolved change in conductivity is s(t) = N(t)em, where N(t) is given by Equation 1.3 and m is the semiconductor mobility. The arrival of the laser pulse is analogous to closing a switch, which allows the antenna gap to conduct. The short recombination time tc of the semiconductor causes the gap resistance to change from nearly insulating to conducting (closing the switch) then back to insulating (opening the switch) on a picosecond time scale. The coplanar strip line is connected to a high-sensitivity current amplifier that detects any current flow through the antenna gap with subpicoamp resolution. If the
7525_C001.indd 10
11/19/07 10:58:55 AM
11
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
ETHz
tB = 0–
tA< 0
(b)
w
h d
E(t) ~ I(t)
(a)
–4 (d)
tC = 0+ (c) tB
tA tC 0 Time (ps)
4
(e)
Figure 1.5 Illustration of the process of THz detection. The THz antenna of frame (d) is shown in cross section in frames (a–c). The electric field measurement is determined by the relative arrival times of the optical and THz pulse. In (a), the optical pulse arrives before the THz pulse. By delaying arrival of the optical pulse to coincide with the THz pulse as shown in (b) and (c), the measured current (e) maps out the THz field in time.
resistance of the metal lines is negligible the resistance of the antenna is determined by the antenna gap. The gap resistance is R(t) = w/s(t)A, where the cross-sectional area, A, is approximately 2da with a the absorption depth in the semiconductor; typically d >> a. The current flow from Ohm’s law is I(t) = V(t)/R(t), where the antenna bias voltage is provided by the THz pulse: V(t) ≅ ETHz(t)h. In Figure 1.5a, the THz pulse has not yet arrived at the antenna, the bias voltage is zero, and there is no net current flow through the antenna. This is illustrated in Figure 1.5e at the point labeled tA, which occurs at t < 0. Figure 1.5b shows a point later in time; the time axis is determined by the delay between the laser pulse that generates the THz pulse and the pulse that gates the THz antenna. The positive gating peak of THz pulse is incident on the antenna at the same time the optical gating pulse arrives. In this case, ETHz > 0, and current flows from the lower half of the antenna to the upper are determined by the electric field direction. The measured time average current at point tB in Figure 1.5e is proportional to the THz electric field. After the current is measured, the delay between the laser generating and gating pulses is again changed to advance the THz pulse in time. Figure 1.5c and point tC in Figure 1.5e both correspond to a point on the pulse where the electric field is opposite in sign to Figure 1.5b. The time resolved
7525_C001.indd 11
11/19/07 10:58:57 AM
12
Terahertz Spectroscopy: Principles and Applications
measurement of the THz pulse electric field is thus made by changing the delay between the optical gating pulse and generating pulse. From this discussion, it is clear that, to measure the electric field with high temporal resolution, the response time of the semiconductor tC must be short compared with the rate of change of the THz field. Because to a first approximation σ ~ µ, semiconductors with both high mobility and short carrier lifetimes are optimal. The two semiconductor materials most commonly used for photoconductive THz detectors are low temperature-grown GaAs and ion implanted silicon on sapphire. Low temperature-grown GaAs has a thin layer grown on a GaAs substrate with the substrate temperature determining the recombination time.16 Recombination times of hundreds of femtoseconds or less have been reported. Silicon on sapphire is a thin (~1 µm) layer of silicon grown on a sapphire wafer with a reduction of carrier lifetime achieved through ion implantation. The carrier lifetime is dependent on implantation dosage to a point at which it saturates at about 500 fs.17 The response time can be estimated by the convolution of the THz pulse electric field, ETHz, with the detector response time determined by s(t). With the optical gating pulse arriving at t = 0 and the THz pulse at t = to, the time average current is:
I (t ) =
2 hr α w
∫
∞
s (t )ETHz (t − t 0 − t)δt
−∞
(1.7)
where the antenna dimensions have been used to estimate the resistance. Equation 1.7 indicates that photoconductors with infinitely short response times excited by infinitely short optical pulses (i.e., a delta function response) are required to exactly measure the time-resolved THz electric field. Although in general short carrier lifetimes allow the faster THz field transients to be measured, there is a tradeoff in actual performance because short lifetimes arise from a high density of trap or defect states that reduce the semiconductor mobility. Additionally, the average current is proportional to the time integral of s(t) so that fast recombination times can lead to lower average current measurements for a given THz field strength. In practice, measuring THz pulses with high-frequency components is more dependent on the laser excitation pulse than the carrier lifetime. This can be understood qualitatively through Equation 1.7 because both step functions and delta functions result in a non-zero average current. The extraction of accurate material parameters for non-ideal measurements of ETHz(t) is discussed later. This section concludes with a brief discussion of the THz antenna structure. Although Equation 1.7 indicates that an increase in the dipole size, h, allows high average currents, this is true only if the antenna length remains much less than the THz wavelength (Hertzian dipole). Longer antenna lengths have resonances and exhibit strong frequency dependence. Because the incoming THz pulse in most cases is incident through the semiconductor substrate, the wavelength of the THz radiation is reduced compared with free space by λo/n. Silicon, GaAs, and sapphire have high refractive indices in the THz region, so at frequencies near 1 THz, the wavelength at the antenna is on the order of 100 µm. A large number of antenna designs have been used both for generation and detection of THz radiation beyond simple dipoles. These include log-spiral18 and bow-tie19 designs.
7525_C001.indd 12
11/19/07 10:58:59 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
13
1.4.1 THz Spectroscopy Using Photoconductive Antennas This section provides an overview of spectroscopic measurements using photoconductive sources and detectors of THz pulses. Much of the discussion also applies to other ultrafast THz generation and detection techniques such as those based on nonlinear optics covered elsewhere in this book. Photoconductive THz pulses offer unique capabilities for spectroscopic measurements in the far infrared spectral region compared with other techniques such as Fourier transform infrared spectroscopy or techniques such as frequency mixing originally developed at microwave frequencies. This section is intended to provide a brief overview of both the advantages and disadvantages of ultrafast THz spectroscopy, describe the basic theory of extracting spectroscopic information from experimental measurements, and discuss experimental considerations of the technique that can affect the spectroscopic measurements. This section also is intended to provide an overview for the researcher looking to use THz pulses for their own spectroscopic measurements and is thus general rather than specific in the material covered. The first question to ask is whether THz spectroscopy is the appropriate technique for a given measurement. The THz spectral region accessible via ultrafast optical pulse generation and detection extends from less than 0.1 THz to more than 30 THz. Some source and detector techniques have enhanced low-frequency response, whereas other techniques are used to achieve high frequencies. Both the high- and low-frequency limits have associated experimental difficulties. The low-frequency end of this spectral region extends to frequencies that are easily achievable using high-precision electronic instruments. In addition, long temporal scans are required. For the high-frequency limit above about 10 THz, highly mature optical spectroscopy techniques such as Fourier transform spectroscopy exist. In brief, the choice to use time-resolved THz spectroscopy techniques depends on specific applications. The advantages of time-resolved THz spectroscopy are: coverage of more than a decade frequency range with a single measurement, peak spectral response in the 0.3–3.0 THz spectral range, and the ability to measure phenomena with subpicosecond time resolution. The THz spectral region is rich in spectroscopic features. Chapters later in this book provide much more complete reviews of the types of systems that can be probed with such pulses. From the perspective of trying to set up a system to perform measurements, THz spectroscopy can be broadly separated into measurement of gases and that of liquids and solids. At the low number density characteristic of gases, the frequency of collisions between molecules determines dephasing times that occur on time scales generally much longer than 1 ps. Spectral features are then less than 1 THz in width and can be less than 1 MHz at low pressures with Q (Dn/no) of 106 or more. In this limit, time-resolved THz spectroscopy resolves individual transitions over a broad range of energies, but does not have the frequency resolution to measure extremely narrow line widths. Limitations on frequency resolution are discussed in detail later. For liquids and solids resonances are broadened on femtosecond timescales resulting in broad, featureless spectra with corresponding to Q < 1 in most cases. For such systems, the spectral width of the short pulse-based measurement techniques can prove extremely valuable. Free carrier absorption occurs
7525_C001.indd 13
11/19/07 10:59:00 AM
14
Terahertz Spectroscopy: Principles and Applications
in semiconductor materials in the THz spectral range and the broad spectral coverage is extremely useful for determining material properties. One other difference between THz spectroscopy and spectroscopic techniques at optical frequencies is that the energies of THz photons correspond to thermally accessible energy states. At room temperature the thermal energy, kT, corresponds to 25 meV, 208 cm–1, or a frequency of 6.25 THz. Thus THz spectroscopy using photoconductive antennas typically covers the region kT > hn where thermal energies are higher than photon energies and can probe states that are populated at room temperature. Using short excitation pulses to achieve high frequencies, it is also possible to simultaneously measure the region hn > kT. The technique of THz time domain spectroscopy measures the change between time-resolved electric fields of THz pulses propagating through a sample and an equivalent length of free space. Depending on the sample geometry, the change in the THz pulse shape permits either analytic or numeric calculation of the complex sample index, permittivity, or conductivity. One assumption in the following treatment of THz time domain spectroscopy is that the interaction of an electric field with a sample is linear. Maxwell’s equation, and Equation 1.1, which describes propagation through a material with constituent parameters given by the permittivity and permeability, is linear for small electric field when higher order terms of the susceptibility can be ignored. THz pulses generated in the laboratory typically have peak powers on the order of 1 µWcm–2 corresponding to an electric field on the order of 1 Vcm–1. Because the assumption of linear interactions in most materials is a good one, linear dispersion theory8 is used to represent the time domain pulse in the frequency domain as a superposition of plane waves of frequency w, all with a k vector along the THz system optical axis, z. The relative amplitude and phase of each plane wave component of the THz pulse are obtained through a Fourier transform of the timeresolved electric field:
E (z , w ) =
1 2p
∫
∞
E (z , t )e − iwt ∂t
−∞
(1.8)
Here E(z,w) is the complex field amplitude and E(z,t) is the experimentally measured THz pulse electric field in the time domain. A typical measurement of two THz pulses is shown in Figure 1.6. The three frames on the left correspond to the reference pulse that has propagated through free space—in this case, nearly dry air. The three frames on the right correspond to the pulse that has propagated through the sample—humid air containing approximately 1 percent water vapor. The experimentally measured pulses are in the top two frames. The effect of water vapor on the THz pulse in the measurements of Figure 1.6a are visible as oscillations after the pulse. Figure 1.6b shows the magnitude of the complex spectral amplitude obtained through a numeric Fourier transform. Comparing the two spectral amplitudes, the discrete rotational transitions of H2O can be seen as distinct absorption lines. The relative phase of the plane wave components that make up the two THz pulses is displayed as modulo 2p in Figure 1.6c. As can be seen from
7525_C001.indd 14
11/19/07 10:59:01 AM
15
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
E(t) (nA)
4 2
(a)
Esamp(t)
Eref(t)
0 –2 0
10
20
0
10
Time (ps)
20
30
Time (ps)
|E(ω)|
1.00
(b)
0.75 0.50
|Esamp(ω)|
|Eref(ω)|
0.25
∠E(ω)
0.00 π
(c)
0 –π 0.0
0.5
1.0
1.5
2.0
0.5
Frequency (THz)
1.0
1.5
2.0
2.5
Frequency (THz)
Figure 1.6 The reference and sample pulses discussed in the text are shown in (a) for dry and humid air. Numerical Fourier transforms of the amplitude and phase, (b) and (c), respectively, illustrate the effect of the sample on the plane wave components that comprise the THz pulse.
the figure, the phase changes linearly except near the resonance of the water vapor rotational frequencies. The gray regions on the plot correspond to invalid phase data caused by the reduced spectral amplitudes beyond 2 THz. Obtaining the complex electric field amplitude spectrum via a Fourier transform permits determination of the complex amplitude after propagating a distance Dz through a sample. Given the measured spectrum at the input of the sample, z = 0, the field exiting the sample is given by:
E ( Dz , w ) = E (0, w )e − ik (w ) Dz
(1.9)
The complex k vector, k(w), expresses complete information about the THz pulse interaction with the sample material. The wave vector k(w) can be expressed several ways, most commonly through the complex index, n(w) = n′(w)-jn″(w) with k(w) = wn(w)/c. The complex index is related to the permittivity through er(w) = n(w)2. The imaginary term is related to the power absorption coefficient by ap(w) = 2wn″(w)/c.
7525_C001.indd 15
11/19/07 10:59:04 AM
16
Terahertz Spectroscopy: Principles and Applications
The choice of sign for the imaginary term of n(w) is made so that plane waves are attenuated and not amplified. The complex, frequency-dependent k vector is then:
k (w ) =
w w[n ′(w ) − 1] i α p (w ) + − 2 c c
(1.10)
where the first term, k0 = w/c, corresponds to the phase change of the THz pulse through a length of free space equivalent to the sample thickness. The reason for expressing the wave vector in this form will be made clear later. To measure the complex refractive index of the sample, a measurement is first done without the sample in place and with the spectrometer purged with dry air to ensure n = 1 along the THz pulse path. The measured THz pulse, Eref (t) in Figure 1.6a, is numerically Fourier transformed to obtain Eref (ω). The measured THz pulse in a general sense can be written as:
E ref (w ) = E gen (w )T (w )H (w ) = E gen (w )T (w )e − ik 0 Dz
(1.11)
where Egen(ω) is the THz pulse generated by the source, T(ω) is the frequency response of the THz spectrometer including the THz source and detector, and H(ω) is the response function of the sample. For the reference sample of length ∆z of free space, H(w) = exp(-ikoDz). The concept of a transfer function is drawn from engineering and describes the effect of a system on a complex input signal. The terms Egen(ω) and T(ω) are not directly measured and depend on numerous experimental parameters and the THz source and detector used. After the sample is placed into the system, the measured pulse that has propagated through the sample is
E samp (w ) = E gen (w )T (w )H (w ) = E gen (w )T (w )e − ik (w ) Dz
(1.12)
The material response is determined by dividing the complex amplitude spectrum of the sample pulse by the free space pulse
E samp (w ) E gen (w )T (w )e − ik (w ) Dz = = e − i ( k (w )− k 0 ) Dz E ref (w ) E gen (w )T (w )e − ik 0 Dz
(1.13)
As can be seen from the k(ω)-ko term of Equation 13, division of the sample spectrum by the reference spectrum effectively removes the effect of an equivalent length of free space. The absorption coefficient and index of refraction can be determined from the magnitude and phase of the spectral ratio using Equation 1.10. The refractive index and absorption coefficient of the time domain measurements of humid air, Figure 1.6, are shown in Figure 1.7. The complex index of the rotational transitions have the form of the quasi-Lorentzian line shape with phase and magnitude similar to that of a harmonic oscillator.20 Besides permitting direct measurement of the
7525_C001.indd 16
11/19/07 10:59:08 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas 2
17
(b)
n(ω)z
1 0 –1 –2 6
(a)
α(ω)z
4 2 0 0.0
0.5
1.0 Frequency (THz)
1.5
2.0
Figure 1.7 Refractive index and absorption coefficient extracted from the data of Figure 1.6.
index and absorption, dividing the Fourier transforms of the measured pulses in the frequency domain is mathematically equivalent to a time domain deconvolution to remove the frequency response of the generated THz pulse and optical system from the sample response function. The effect of this deconvolution is one reason that the response time of the semiconductor does not need to be much shorter than the rate of change of the THz field to perform high-resolution THz spectroscopy. The formalism of the transfer function in the derivation above is useful because most samples measured with THz time domain spectroscopy do not have simple transfer functions. The derivation previously considered propagation in which the Fresnel reflection and transmission coefficients can be ignored. A more general case is the measurement of a finite thickness of material with index n2(w) surrounded by a material of index n1(w), usually air, so n1 = 1. In this case the Fresnel coefficients need to be taken into account and the transfer function H(ω) is then defined as:21
H (w ) =
t12t 21e ib (1 − r12r21e i 2b
)
(1.14)
where t12(w), t21(w), r11(w), and r 21(w) are the Fresnel transmission and reflection coefficients21 and depend on the index of the sample, n2(w). b = n2 kodcos q is the phase delay associated with multiple reflections inside the slab where q is the angle of propagation inside the slab determined from Snell’s law. Although there are no
7525_C001.indd 17
11/19/07 10:59:10 AM
18
Terahertz Spectroscopy: Principles and Applications
exact analytical solutions for the index and absorption coefficient, the equation can be solved numerically either using an iterative guessing approach or piecewise in frequency trying to minimize phase and magnitude errors.22 Analytical approximations also serve in many cases. Although Equation 1.14 describes propagation through a dielectric slab, any other sample geometry can be represented equally well with the transfer function formalism. Assuming that the system being measured is one for which linear dispersion theory applies, after the system transfer function is determined, the THz measurements can compared with theory with equal ease in either the frequency or time domain. For a known H(ω) the time domain THz pulse is calculated after propagating through the sample from the inverse Fourier transform:
E samp (t ) =
∫
∞
E ref (w )H (w )e − i (wt )∂w
−∞
(1.15)
To summarize the process for extracting the index and absorption from measurements of the THz pulse, the THz pulse is Fourier transformed to express it in terms of a plane wave expansion. Taking the ratio of a THz pulse transmitted through a sample to one through a reference sample with known index deconvolves the response of the THz antenna and optical system and returns the sample transfer function. The index and absorption data are extracted from an analytic expression for the sample transfer function H(w). The complex index is measured over the system bandwidth without resorting to Kramers-Kronig analysis. As with any experimental technique, there are several assumptions inherent to the treatment discussed previously that can affect the results. The most common source of error arises from fluctuations of the THz pulse shape over the course of the measurement. Because two THz pulses—a reference pulse and a sample pulse—are measured to extract the complex index, any changes in the THz pulse shape over the duration of the measurement result in errors of the measured index. Relatively long-term experimental system drifts can be difficult to control so due experimental diligence and careful experimental design are required to avoid long-term drifts from thermal or mechanical fluctuations. Linear dispersion theory requires that the THz pulse can be expanded into a superposition of plane waves propagating along the z axis. Unlike laser beams at optical frequencies, this is not always true for THz pulses. Typical THz beam diameters are approximately 1 cm or less with a wavelength from millimeters to tens of microns. The beam diameter:wavelength ratio then ranges from 3 to 100 compared with values of several thousand for optical beams. Thus THz beams are more correctly represented as a summation of plane waves over a range of angles to the z axis. The angular spread of the k vectors can be estimated from Dq = 2Dk x/ko with ko = w/c, Dk x ≅ (2Dx)–1 and ∆x ≅ 1 cm. The angular spread is then on the order 0.3° at 1 THz and 0.9° at 0.3 THz. The angular spread of the beam can affect the measured transmission of samples angled to the beam.23 If the spatial profile of the THz pulse is measured, a spatial Fourier transform permits the angular-dependent transmission of the sample to be resolved.
7525_C001.indd 18
11/19/07 10:59:12 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
19
A final assumption is that the shape of the THz beam is not changed by passing through the sample. Referring to Equation 1.13, it was assumed that transmission through the sample does not affect T(w). Again, this is usually not an issue with optical beams, and is generally true for thin, low index samples that do not act as optical elements. The larger effect of diffraction at THz frequencies can result in beam reshaping for thick samples of high index. Techniques to calculate the effect of the sample on the THz beam will be discussed in the following section on experimental considerations of THz spectroscopy.
1.5 Experimental Considerations of TerahertZ Spectroscopy The basic technique of THz time domain spectroscopy using photoconductive switches has been outlined previously from the viewpoints of the fundamental physics of the THz generation and detection process and also from the mathematical treatment of extracting complex index from measurements. This section introduces the third element required for successful THz spectroscopic measurement: the experimental measurement system. This section is divided into three parts that attempt to provide practical considerations for performing THz spectroscopy: the optical pulses used to generate and detect the THz pulse, the propagation and coupling of the THz beam from source to detector, and miscellaneous experimental considerations required for successful measurements. A simplified schematic representation of a simple THz spectroscopy setup is shown in Figure 1.8. On the left side of the figure, a femtosecond laser provides a pulse train of femtosecond pulses. A beamsplitter separates the pulse train into beams that go to the THz source and detectors with nominally equivalent power. In Figure 1.8, the optical pulse going to the THz source (a) passes through an adjustable delay. The THz pulse created by the THz source (b) goes through several beamforming optics, passes through the sample, which changes the pulse shape (c), and is incident on the THz detector. The second optical pulse (d) arrives at nominally the
fs Laser Beamsplitter
Optical Delay (a)
THz Source
THz Detector
Sample
(b)
(c) (d)
Figure 1.8 Schematic illustration of a THz spectrometer showing the laser excitation source, optical delay line, THz source and detector, and THz coupling optics.
7525_C001.indd 19
11/19/07 10:59:14 AM
20
Terahertz Spectroscopy: Principles and Applications
same time as the THz pulse and gates the THz detector. Changes in the delay permit the THz pulse shape to be mapped out as discussed in previous sections. A key experimental issue is ensuring the time of arrival of the THz pulse on the detecting dipole antenna coincides with the arrival of the optical pulse. The laser source and associated optics are shown on the left side of Figure 1.8. THz spectroscopy using photoconductive switches can be done successfully using a wide range of laser excitation sources. There are a large number of ways to specify or characterize laser sources, some of which have a strong impact on THz spectroscopic measurements and others that are much less important. The characteristics of the laser source are discussed briefly in decreasing order of importance. The ranking in importance is rather arbitrary and other experimental data can certainly change the required laser source characteristics. Arguably the most important characteristic of the laser source is stability, defined as constant power output and beam pointing over periods longer than several seconds. The importance of this for THz spectroscopic measurements arises from the need to measure two data scans for the reference and sample. Because the complex index is determined by the ratio of the two data scans, any change in the laser power or beam position can introduce large errors in measurements. Experimentally, measurements usually are performed by taking a reference scan before and after a scan with the sample in the beam in order to determine if there has been any drift of the system during the measurement period. Temperature fluctuations in the laboratory or problems with optical beam pointing stability can also degrade measurements. Figure 1.9a illustrates differences between two commercial laser sources determined by measuring the peak of the THz signal—point tB in Figure 1.5—over 30 minutes. As can be seen from the figure, there is a significant difference in stability between different sources. Of nearly equal importance to medium-term stability is the optical noise of the laser source. The primary noise source on THz experiments is noise from the laser coupled onto the THz beam.24 The noise specification of interest depends on the data acquisition technique. For the majority of THz experiments, phase-sensitive or lock-in detection is used and the noise figure of interest is the noise at the modulation frequency of the THz time domain spectroscopy system. For data acquisition systems that use rapid scanning and signal averaging, the noise at lower frequencies is of more importance. Figure 1.9b shows the effect of the stability and noise of the laser sources on the spectral representation of data used to determine the complex index through THz spectroscopy. The figures show ratios of the magnitude of the spectral amplitudes of five sequential reference scans, |EN|/|EM| where M ≠ N, performed in dry air. The variation between separate ratios indicates approximately the accuracy of the transfer function which is used to determine the complex index. Laser 1, with less noise and drift, results in a transfer function accurate to about ±1% over a large bandwidth. The noisier laser 2 has a factor of three less accuracy. The experimental artifact near 1.6 THz is due to small changes in the water vapor content in the experimental system on the order of less than 2%. The increasing error of the ratios at low and high frequencies is due to the finite bandwidth of the THz system.25 A third important, but not necessarily vital, specification of the laser source is the optical pulse width, which under some experimental circumstances, has a critical effect on the THz signal bandwidth.
7525_C001.indd 20
11/19/07 10:59:15 AM
21
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
Normalized Peak Signal (%)
+1
Commercial Laser #1
0 –1 +3
Commercial Laser #2
+2 +1 0 –1 –2
0
10
20
Time (minutes)
30
Ratio of Spectral Amplitudes (%)
(a) 105 100 Commercial Laser #1
95 110
Commercial Laser #2 100
90
|EN| |EM| 0
0.4
0.8
1.2
1.6
2
Frequency (THz) (b)
Figure 1.9 The upper figure, (a), compares the peak THz signals measured for two commercial laser sources over a 30-minute period to illustrate the impact of the excitation source on system signal-to-noise ratio. The lower figure, (b), compares five consecutive scans with the two laser sources illustrating how short-term stability impacts measurement accuracy.
For experiments using photoconductive switches over the spectral range 0.1–3 THz, the laser pulse width is not generally the limiting factor to the system bandwidth. Rather, the optical system and dipole response limit the bandwidth. However, to reach higher THz frequencies using relatively short dipole antennas on semiconductor substrates with fast response time, the bandwidth is critically dependent on the laser pulse width because the rise time of the conductivity limits the system spectral response. As a rule of thumb, pulse widths lower than 100 fs are more than adequate for most THz experiments and noise considerations can have a much larger effect on the effective system bandwidth than the laser pulse width. This is illustrated in Figure 1.10, in which the Fourier transforms of the five consecutive scans of Figure 1.9 are shown on a logarithmic scale for the two commercial lasers. The pulse width of the first laser, on the upper half of the figure, is specified by the manufacturer as <150 fs, and has an autocorrelation width of 110 fs. The second laser produces
7525_C001.indd 21
11/19/07 10:59:17 AM
22
Terahertz Spectroscopy: Principles and Applications Commercial Laser #1
104 103
Relative Amplitude
102 101 100 Commercial Laser #2
104 103 102 101 100
0
1
2
3
4
Frequency (THz)
Figure 1.10 Comparison of the measured amplitude spectra of the two commercial lasers of Figure 1.9 illustrating the effect of laser amplitude noise on the THz spectral amplitudes. Laser 1 has a longer pulse width than laser 2.
much shorter pulses with an autocorrelation width of 55 fs. Although water lines are visible out to 4 THz for the longer pulse laser, the noise makes them impossible to distinguish for the second laser with shorter pulse widths. Of relatively less importance is the output power of the laser source, because most femtosecond sources will operate at higher than 100 mW of output power, whereas the typical THz system built around photoconductive switches only needs about 50 mW of total optical power to generate good experimental data. Using optical beams focused to about 5 µm, the semiconductor on which the detector is fabricated saturates at tens of milliwatts of optical power. Increasing optical power beyond the point of saturation has different effects on the THz source and detector. As the optical power on the source reaches saturation, the laser noise coupled in on the optical gating beam rises faster than the detector signals response resulting in decreased signal to noise of the system. At the THz source, the generated THz signal increases with optical power sublinearly following saturation. Of greater practical importance, the combination of high electric field and optical power can lead to electromigration12 and catastrophic failure of the THz source. The effect on saturation on the system dynamic range is shown in Figure 1.11. The dynamic range is defined in this chapter to be the RMS noise of the system before the arrival of the THz pulse compared with the signal at the peak of the THz pulse. The dynamic range of the system rises to a peak at 30 mW of excitation power then begins to decrease. This is mirrored in the inset that shows the measured THz signal increase linearly with excitation power until saturation at a power of tens of milliwatts.
7525_C001.indd 22
11/19/07 10:59:19 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
23
Dynamic Range (unitless)
20,000
Measured Signal
1000 30,000
100
30 µm dipole
10 1 0.1 0.01
0.01 0.1 1 10 100 Probe Average Power (mW)
10,000
0 0.1
1.0
10
100
Receiver Excitation Optical Power (mW)
Figure 1.11 Effect of optical excitation on the THz detector dynamic range. Increasing power beyond 30 mW decreases the dynamic range because of an increase of noise in conjunction with saturation of the detector as shown in the inset.
Assuming the laser operates at a photon energy above the bandgap of the semiconductor material used for the photoconductive antennas, the wavelength has secondary importance for THz spectroscopy. There have been reports in the literature, however, of improved THz emission efficiency near the bandgap.26 For most semiconductor materials, the need to excite above the bandgap rules out fiber lasers operating in the 1,550-nm range, although frequency-doubled fiber lasers are routinely used for THz spectroscopy. The pulse repetition frequency of the laser does affect spectroscopy using photoconductive switches, but pulse repetition frequencies of tens to hundreds of megahertz have been demonstrated. Lower repetition rate sources, such as those from amplified lasers, are more problematic because the pulse energy can cause saturation. In this case, large-aperture sources are used.27 The optical delay line shown in Figure 1.8 permits the relative delay of the THz pulse and optical gating pulse on the THz detector to be changed to map out the THz pulse shape. Because the Fourier transform used to convert the pulse to a spectral amplitude assumes the temporal spacing between the points is uniform, numeric linearization of the points is required if the delay line does not move linearly. The properties of the Fourier transform also show the measurement bandwidth is numerically limited by the Nyquist frequency, (2Dt)–1, where Dt is the time step of the delay line. Typically, Dt is chosen so that the Nyquist frequency is two or three times larger than the system bandwidth. This is done both to avoid wraparound in the frequency domain,28 but also to oversample the THz pulse shape so that noise fluctuations have less effect on the data. The frequency resolution of time domain THz measurements depends critically on the delay line parameters. The frequency resolution, Dn, is inversely proportional
7525_C001.indd 23
11/19/07 10:59:20 AM
24
Terahertz Spectroscopy: Principles and Applications
to the number of data points acquired for a fixed time step and given by Dn = (2NDt)–1, where N is the number of data points. The resolution is usually not an issue for solid or liquid samples that have broad resonances, but for gases, the measured line width is often experimentally limited. As a rule of thumb, the experimentally resolvable line width is given by 0.6(NDt)–1. For a 100-ps measurement scan, this corresponds to 6 GHz spectral resolution. Because the overall noise measured increases as the square root of the size of the measurement window, it is clear that time domain THz techniques are generally not suitable for high-frequency resolution measurements.
1.6 TerahertZ Beam Propagation and Optical Systems In performing THz time domain spectroscopy measurements, a second critical element is ensuring there is good coupling between the THz source and THz detector. The effects of propagation and coupling considerations on experimental measurements are much more critical for THz experiments than for similar experiments at optical frequencies. There are several reasons for the increased care that needs to be taken in ensuring good coupling. First, the requirement that the photoconductive THz antenna is much smaller than a wavelength means the antenna is not highly directional. Additional coupling optics are required to produce a well collimated THz beam. Second, because the wavelength-to-beam diameter ratio is much less for THz pulses than for optical pulses, diffraction plays a larger role in beam propagation and the THz beam can quickly exceed the size of optics. Third, because the frequency components that make up the THz pulse typically cover more than a decade in frequency, different frequencies of the pulse have very different propagation characteristics. Finally, the THz detector measures the field rather than intensity of the THz pulse so it is not sufficient simply to get power to the detector. The spatial profile of the field pattern needs to match that of the detector. These considerations are discussed in the remainder of this section. Figure 1.12 shows a silicon—or other high-index material—lens attached to the back of the semiconductor wafer used for the THz source for the two orthogonal planes corresponding to S and P polarization of the THz radiation from the dipole antenna. As illustrated in the figure on the right, the silicon lens is centered on the dipole so that radiation from the antenna is collimated. The radiation of a dipole on a surface has a radiation pattern considerably different from a dipole in free space. The radiation patterns for S and P polarization are shown as shaded regions in Figure 1.12 on both sides of the dielectric interface of the THz antenna substrate. The reduced size of the antenna pattern in free space corresponds to the n3 reduction of the THz power radiated into space compared to that radiated into the dielectric as discussed previously.29 The radiation pattern of the Hertzian dipole on the surface leads to a complex radiation pattern on the surface of the lens.30 This radiation then diffracts to form an approximately Gaussian distribution in the far field.11,30 The antenna pattern inside the lens is, to first order, independent of frequency so that the field pattern at the lens surface is also frequency-independent. Because the more localized field patterns on the lens surface diffract strongly and do not contribute in a major way to the signal in the far field, a good first-order approximation is to assume there is a frequency-independent Gaussian beam waist at the coupling lens.
7525_C001.indd 24
11/19/07 10:59:21 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
25
Figure 1.12 Illustration of the antenna patterns for a dipole on a surface for P polarization (left) and S polarization (right). The rays in the figure are calculated from a geometrical optics approximation and illustrate the effect of spherical aberration resulting from the strongly curved lens surface.
The assumption of a frequency-independent Gaussian beam waist at the coupling lens allows the use of simple Gaussian beam theory to be useful for predicting THz beam propagation. Although other methods of calculating propagation of THz beams can also be used, the Gaussian treatment provides a compromise that is more precise than simple ray approximation, and less computationally intensive than finite difference time domain methods. For a Gaussian beam with waist wo at z = 0 and frequency ω, the field pattern at a distance z is given by:31
E (w , r , z ) = E 0 (w )
w0 r2 − 2 w (w , z ) w (w , z )
z w z r 2w − tan −1 × exp − j exp − j c z 0 (w ) 2cR (w , z )
(1.16)
where r is the radial distance in the x-y plane and the Rayleigh range, zo, is given by:
Z0 =
ww 02 2c
(1.17)
The waist at distance z for frequency ω is written in terms of the Rayleigh range as: 2 z w (z ) = w 1 + z0 2 0
(1.18)
This is the standard theoretical treatment used for description of laser beam propagation, but unlike the more familiar propagation of a single-frequency beam, the
7525_C001.indd 25
11/19/07 10:59:26 AM
26
Terahertz Spectroscopy: Principles and Applications
THz pulse is a superposition of a wide range of frequencies. As a result, the Rayleigh range and waist size are not single-valued at a given distance and the different frequency components of the THz beam have different propagation characteristics. The following paragraphs provide an overview of some of the propagation characteristics of THz beam; for a more complete treatment, the reader is referred to previous work.32 The Rayleigh range dictates the distance from the waist at which the propagating beam goes from propagating with minimal divergence and planar phase fronts to divergent propagation at angle θ = 2c/pnwo with spherical phase fronts. Alternatively it roughly demarcates the regions of near-field and far-field propagation. From Equation 1.17, using commonly encountered lens radii of several millimeters, the Rayleigh range is given approximately as zo ≅ 10ν (cm) where ν is the frequency in THz. Considering that typical propagation distances in a THz spectrometer are less than 1 m, both near-field and far-field behavior is exhibited simultaneously in the system by different frequency components. These variations in the Rayleigh range across the bandwidth of the THz pulse are reflected in the divergence full angle of the beam in the far field, θ, and the corresponding spread of the 1/e beam waist of the THz beam w(z). In the far field where z >> zo, the divergence full angle scales approximately as θ(n) ≅ .06/n (rad), whereas the beam waist scales as w(z) ≅ 0.03z/n (cm). This is illustrated graphically in Figure 1.13 that shows propagation of 0.1, 0.3, 1.0, 3.0, and 10.0 THz components of a THz pulse propagating a distance of 1 m from a lenscoupled THz source as calculated from Equation 1.16. At 100 cm distance, the beam at 0.3 THz has a radius of 10 cm; in practice, freely propagating THz beams cover much smaller distances and diffraction is controlled using optics. Because of the differing propagation characteristics of different frequency components of the THz beam, the propagation of THz beams through optical systems
100
Waist Radius, w(z) (cm)
0.1 THz 0.3 THz
10
1 THz 3 THz
1.0
10 THz 0.1
0
20
40
60
80
100
Distance from Source, z (cm)
Figure 1.13 Variation of the THz beam waist radius (1/e amplitude point) with distance from the lens-coupled, photoconductive THz source.
7525_C001.indd 26
11/19/07 10:59:28 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
27
exhibits effects that are not commonly seen at optical frequencies. A good first-order approximation of THz beam propagation through optical systems that assumes paraxial propagation and ignores aberrations and aperturing effects of mirrors can be made using Gaussian beam formalism combined with the ABCD matrix method for describing optical systems.31 To calculate propagation through optical systems, both the amplitude and phase terms, w(w,z) and R(w,z), respectively, are represented by the complex q parameter: 2c / w 1 1 ≡ −j 2 q ( w , z ) R( w , z ) w (w, z )
(1.19)
As the THz beam propagates through an optical system with a given ABCD matrix, the phase and amplitude profiles are changed, which transforms the q parameter according to:
1 = qout
C +D 1 q in A + B 1 q in
(1.20)
where qin is the q parameter at the input plane of the optical system, which is usually defined as the THz source coupling lens and qout is the value at the system output, usually the coupling lens of the THz detector. To achieve optimal power transfer, the beam that is detected at the receiver must have an identical phase and amplitude profile to the emitted THz beam at all component frequencies.32 It can be shown that this occurs if the phase and amplitude profiles of the beam from the THz source and a hypothetical beam from the THz detector fully overlap at some point in the system. The coupling efficiency is determined by integrating the normalized field profiles of the beam from the source and the hypothetical detector beam over a plane at some point in the system.32 The normalized power coupling is then given by:
Cp =
∫∫
∫∫
E s (w , z )E D (w , z ) * dS
E s (w , z )ES (w , z ) * dS ×
∫∫
2
E D (w , z )E D (w , z ) * dS
(1.21)
where for TEM0,0 modes the source and detector beams are given by ES (w,z) and ED (w,z), respectively. For ideal coupling, CP must be in unity for all the frequencies comprising the THz pulse. Assuming the THz source and THz detector are identical, unity power coupling occurs when the beam at the output of the optical system has identical phase and amplitude profiles to that at the input so that qout = qin. From Equation 1.20, this condition requires that the elements along the main diagonal of the ABCD matrix,
7525_C001.indd 27
11/19/07 10:59:31 AM
28
Terahertz Spectroscopy: Principles and Applications 0.1 THz ƒ1
ƒ1
0.3 THz 1 THz
3 THz 10 THz ƒ1
ƒ1
2ƒ1 (a)
ƒ2
ƒ1
ƒ1
ƒ 1 + ƒ2
ƒ2
2ƒ2
ƒ1
ƒ1 + ƒ2
ƒ1
(b)
Figure 1.14 Two common configurations of THz spectrometers. The configuration shown in (a) is a confocal system with a frequency-dependent beam waist at the midpoint of the system. The configuration of (b) is commonly used in THz imaging systems and creates a frequency-independent waist between the short focal length lenses, ƒ2.
A and D, have values ±1 and the off-diagonal elements; B and C are zero—in other words, a unity transfer function. T(w), with ideal coupling for all THz frequencies is achieved for optical systems whose ABCD matrix is the identity matrix, I. Two separate optical systems with unity coupling and an identity transfer matrix are shown in Figure 1.14 along with the calculated beam diameters (1/e amplitude point) at 0.1 THz, 0.3 THz, 1.0 THz, 3.0 THz, and 10 THz. In both systems, lenses are spaced from each other by the sum of their focal lengths. Figure 1.14a illustrates the most common system for THz spectroscopy. Because the field pattern at the back focal plane of a lens is the spatial Fourier transform of the pattern at the front focal plane, the frequency-independent Gaussian beam waist at the coupling lens forms overlapping frequency dependent waists midway between the two lenses in Figure 1.14a. This frequency-dependent waist pattern is then transformed back to a frequency independent waist at the THz detector. The fact that most samples are placed midway between the two lenses for THz spectroscopy needs to be accounted for in data analysis because experimental artifacts from the frequency-dependent waist size can be introduced if the sample is not uniform over large areas. One method of
7525_C001.indd 28
11/19/07 10:59:32 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
∆z = 10%
1 Power Coupling Efficiency, CP
29
∆z = 20%
0.8 0.6
∆z = 10%
0.4 Figure 14(a) Figure 14(b)
0.2 0
0
2
∆z = 20%
6 4 Frequency (THz)
8
10
Figure 1.15 Effect of changing the spacing of focusing optics by 10% and 20% on the frequency-dependent THz power coupling efficiency for the optical configurations shown in Figure 1.14. The amplitude coupling coefficient can be determined by the square root of the plotted values.
measuring nonuniform samples or those with small area is shown in Figure 1.14b. Here, ƒ2 = ¼ƒ1 and the THz beam midway between the two short focal length lenses has a frequency-independent beam waist that is four times smaller than that created by the THz source. This configuration is often used in THz imaging applications33 in which a sample is raster-scanned at the beam waist. THz beam waist diameters smaller than 1 mm can be routinely achieved in this configuration. For both configurations shown in Figure 1.14, the spacing between the lenses affects the frequency-dependent coupling efficiency. The coupling efficiency is shown in Figure 1.15 as a function of frequency at lens spacings corresponding to 80% and 90% of the ideal distances in Figure 1.14, 2ƒ1 or ƒ1 + ƒ2, respectively. As can be seen from the figure, the optical transfer function is an important parameter for the design of any terahertz system. For nonideal optical configurations, it is possible to choose corrective optics to ensure the system has a unity transfer by simply finding the matrix inverse of the transfer function. Because T(w)T(w)–1 = ±I where I is the identity matrix, for nonideal system with transfer matrix T(w), the matrix T(w)–1 gives the transfer function of the corrective optics required to achieve unity coupling. For complex THz optical systems, it is good practice to build THz beam optics in blocks so that the transfer function of each block is the identity matrix. The general treatment outlined previously in this chapter can also be used when coupling THz pulses into waveguides or other photonic devices.34 In this case, the overlap integral is done between the waveguide or device modes and the free-space THz beam. Two final considerations are important when designing THz spectroscopy systems. First, as mentioned previously, the TEM0,0 Gaussian beam formalism is a useful approximation, but it suffers from the fact that the antenna pattern at the lens surface is not a true Gaussian. The propagation can be more precisely, but not
7525_C001.indd 29
11/19/07 10:59:34 AM
30
Terahertz Spectroscopy: Principles and Applications
uniquely, described in terms of a summation higher order Laguerre-Gauss modes.30 The coupling theory still applies in this case for each of the orthogonal modes. For most situations involving beam propagation, the TEM0,0 approximation has acceptable limits of error and the increased complexity of a full modal expansion is unwarranted. There are, however, several situations where the more complex description of the beam profile may need to be accounted for. The first of these is in the near-field region of the coupling lens, where z << zo. A second situation is when coupling to waveguides or other photonic devices. Last, a brief mention will be made of optical materials at THz frequencies. Most optical glasses are, for practical purposes, opaque at THz frequencies. Exceptions are fused silica, crystalline quartz, and sapphire, although sapphire is highly birefringent.35 In addition, the refractive indices of most materials at THz frequencies are much higher than the indices at optical frequencies. For example, sapphire has an index of approximately 1.7 at optical frequencies and ordinary and extraordinary indices of 3.1 and 3.4 at THz frequencies, whereas fused silica has an index near 2.0. All these materials are somewhat lossy—with the absorption generally increasing with frequency—and highly dispersive compared with their properties at optical frequencies. High-resistivity silicon of greater than 1 kΩ cm has extremely low loss compared with other optical materials and is nearly dispersionless and not birefringent. The relatively high index, n = 3.42, leads to large losses because of Fresnel reflections; the amplitude transmission coefficient of a silicon slab is 0.7. Standard quarter-wave index matching methods for creating antireflection coatings do not work for THz pulses because of the extremely broad bandwidth. As a result, many THz systems use reflective optics, particularly off-axis parabolic mirrors. The reflectivity of most metals is effectively 100% across the THz band and, because of the long wavelength, there are not strict requirements for surface polishing. For example, l/20 surface smoothness at 3 THz is 5 µm, which can be achieved in metals using medium grit sandpaper. Any commercially available metal optics generally work well for THz applications.
1.7 Adaptations and Extensions of TerahertZ Spectroscopy Systems The basic technique of THz spectroscopy outlined previously has been adapted by many investigators to extend the capabilities of THz spectroscopy to measure a wide range of samples. There are too many variations to go into in detail, and many of these are covered more completely in later chapters of this book. The variations of THz spectroscopy can be broadly broken down into two categories. The first is techniques that measure the phase-coherent THz pulse shape to extract the optical properties of a sample across a broad range of wavelengths in the far infrared spectral region. Although the experiment measures the electric field with subpicosecond resolution, the information that is obtained has no inherent time dependence. In these measurements, the sample itself is in equilibrium; it does not change on a fast time scale. The second category is measurements that create an optically induced time-dependent change to the sample and can provide fundamentally different spectroscopic information.
7525_C001.indd 30
11/19/07 10:59:35 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
31
Among the first set of variations of the basic spectroscopic technique are those developed to measure samples with small index and absorption such as thin films. Because THz spectroscopy measures the changes of the transmitted spectra, any noise on the THz signal contributes to measurement errors. The dynamic range— defined as the RMS noise of the THz detector compared to the peak THz signal—of THz spectroscopy using photoconductive antennas is extremely high, typically more than 10,000. However, the precision with which spectroscopic data can be measured is limited by the noise on the laser source, which is typically 0.1 to 1%. For low values of the sample absorbance, e–ad ≅ 1-ad, and for values of αd ≤ 10 –2 the change in transmission approaches the measurement accuracy. The sample refractive index can be measured with better accuracy because the index causes a temporal shift of the THz pulse by an amount Dt ≅ nd/c and jitter noise is generally much lower than amplitude noise. Time shifts of tens of femtoseconds can generally be resolved so that index thickness values of nd > 10 –3 cm can be accurately measured. To improve the accuracy for thin film or low absorbance samples several techniques have been developed. The most widely used is known as differential time domain spectroscopy.36 In differential time domain spectroscopy, the sample position is spatially modulated as shown in Figure 1.16a so that the sample moves in and out of the THz beam, which is focused to a small spot size. The film on a substrate is attached to a shaker operating at frequency fs. The difference between the sample and reference signals, Eref (t)-Esamp(t), is measured by a phase-sensitive detector that detects only the modulated signal. Because the THz pulse is not modulated, the noise on the THz background spectrum is effectively eliminated. The measurement of a difference between the reference and sample scans rather than a ratio complicates data analysis. Approximate analytic expressions for the index and absorption have been developed,35 and spectroscopic information can also be extracted numerically.
Shaker fs Beamsplitter
Sample
Al Film
nfilm nair
nsub Iamp
(a)
LIA Silicon Prisms fs
(b)
Figure 1.16 Two experimental configurations used for measuring thin film samples with thickness much less than one wavelength. The differential time domain spectroscopy (DTDS) system is shown in (a) while a system for interferometric THz measurements is shown in (b).
7525_C001.indd 31
11/19/07 10:59:37 AM
32
Terahertz Spectroscopy: Principles and Applications
Using combinations of lock-in amplifiers, it is possible to measure samples with thicknesses of less than 100 nm and simultaneously extract the THz reference pulse using a single measurement.37,38 Extremely high-power dynamic ranges down to –80 dB have also been reported using this technique.39 An alternative technique to measure thin films is to create destructive interference between two THz pulses by splitting the THz pulse train into two equal parts and providing a near-π, frequency-independent phase shift to one of the pulses.40,41 Experimentally, this can be accomplished using a Michelson or Mach-Zender interferometer. Destructive interference between the pulses eliminates the background signal, drift, and some sources. Because of the broad spectral bandwidth, adjusting the phase through path length changes is not possible so the phase shift is accomplished from a Gouy phase shift,10 total internal reflection,9 or geometrical rotation of the electric field vector with a roof mirror.42 An experimental configuration for a THz interferometer is shown in Figure 1.16b. The Michaelson configuration achieves a near-π phase shift through total internal reflection in two silicon prisms, of which one face has been aluminized. The film thickness resolution of THz interferometric measurements is determined by the Sparrow criterion43; for typical THz photoconductive sources and detectors, time resolution of 1 fs is resolvable corresponding to measurements of films on the order of hundreds of nanometers of thickness. A second modification of THz spectroscopy systems is to measure the THz signal reflected or scattered from a sample rather than the transmitted THz pulse. A typical configuration for reflection measurements is shown in Figure 1.17. The THz pulse from the source can be scattered from the sample as shown in Figure 1.17a or reflected specularly as shown in Figure 1.17b. The detector used to measure the scattered pulse is fiber-coupled so the scattering angle β can be varied. Fiber-coupling photoconductive antennas are accomplished by prechirping the optical pulse so that the pulse is recompressed at the output of the fiber.
θ θ
β Optical Fiber Scattered THz Pulse
Fiber Coupled Detector (a)
(b)
Figure 1.17 THz scattering (a) and reflection (b) experimental configurations.
7525_C001.indd 32
11/19/07 10:59:39 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
33
It is more difficult to extract spectroscopic information from scattered or reflected pulses than it is from THz transmission measurements. For the specularly reflected pulse, the reflection coefficient is primarily determined by the nonresonant index. Rarely are there large enough changes in the real part of the index to result in large changes in the reflection coefficient. Additionally, there is no temporal shift of the THz pulse as there is in transmission measurements. As a rough estimate, the normalized change in reflectivity, DR/R, is approximately equal to the normalized change in index, Dn/n, with larger reflectivity changes for lower index materials. The complex index n″ is related to the absorption coefficient by n″ = a/2ko, where ko is the wave vector in free space with a value of approximately 2 × 10 4 m–1 at 1 THz. Except for extremely lossy materials, the real part of the index dominates the imaginary component and contributes negligibly to the reflection coefficient. It is possible to characterize a sample using THz ellipsometry44 and also to make spectroscopic measurements near Brewster’s angle 45 where the reflection coefficient has large changes. For nonspecular reflection, the scattered THz pulse depends to a much larger extent on the sample geometry than the sample composition. Various wave front reconstruction techniques can be used to reconstruct the sample from the scattered wave front; these are discussed in subsequent chapters. Besides adapting the basic technique of photoconductive THz spectroscopy through sample modulation or to measure reflection, it is possible to use photoconductive THz spectroscopy to measure the time-dependent change of a sample after external optical perturbation. Two common ways to accomplish this are optical pump THz probe spectroscopy and THz emission spectroscopy. This chapter concludes with an overview of these techniques with selected experimental results. Optical pump THz probe spectroscopy optically excites a sample with an ultrafast pulse and measures the dynamic processes that occur in the sample by probing with a THz pulse. The experimental modification required for optical pump THz probe spectroscopy shown in Figure 1.18 permits measurements of an optically excited
THz Source τTHz THz Detector fs Laser τopt
Figure 1.18 Schematic experimental configuration of optical pump THz probe spectroscopy described in the text.
7525_C001.indd 33
11/19/07 10:59:40 AM
34
Terahertz Spectroscopy: Principles and Applications
sample in the far infrared spectral region with picosecond time resolution. To minimize timing jitter between the optical excitation of the sample and the THz probe, the excitation pulse typically comes from the same THz source used to generate and detect the THz pulses. For this reason, an amplified laser system is often required to ensure there is sufficient excitation pulse energy to cause a measurable change in the sample. The timing between optical and THz pulses is controlled using two delay lines as shown in the figure. The delay line labeled τTHz is used to delay the optical gating pulse for the THz detector, so that the THz electric field can be mapped out in time. The delay line labeled τOPT changes the delay between the arrival of the optical and THz pulses on the sample. The THz optical system has also been modified by adding additional focusing optics to create a small, frequency-independent beam waist to maximize overlap of the THz and optical pulses. Ultrafast optical beams with a TEM0,0 Gaussian profile and a center wavelength of λ ideally have spot size of approximately wf = λƒ/πd where wf is the radius of the focused beam waist, ƒ is the lens focal length, and d is the laser spot diameter. Because the optical wavelengths are submicron size, whereas THz wavelengths are submillimeter size, without careful selection of optics there is poor overlap which can result in data with experimental artifacts. The optical pump THz probe experiment measures a time-resolved THz pulse for different delays between the THz probe and optical pump pulses, E(tTHz,topt). When the optical delay is zero, topt = 0, the THz and optical pulses arrive at the sample at the same time. As in simple THz spectroscopy (Figure 1.8), a reference pulse is needed, and the THz pulse measured before the arrival of the optical pulse is used as the reference pulse, Eref (t, topt < 0). The THz pulse measured after arrival of the optical pulse constitutes the sample pulse, Esamp(t, topt > 0). The dynamic response of the sample to optical excitation, H(w,topt), can then be mapped out as a function of time. Inherent in the analysis given previously was the assumption that the properties of the sample are time invariant during transmission of the THz pulse. Because the THz pulse may be of longer temporal duration than the sample properties being measured this assumption may not be true in optical pump THz probe measurements. In this case, determining the dynamic response of the sample is done by deconvolving the THz pulse from the time-dependent complex refractive index. There are many reports in the literature of optical pump THz probe spectroscopy that have been used to make measurements that are difficult using other spectroscopic techniques; for example, the optical pump pulse is able to create charge carriers in normally insulating materials in order to measure time-resolved carrier dynamics. The acceleration of the created charge carriers by the THz electric field attenuates the THz probe pulse allowing the complex conductivity as a function of THz frequency and as a function of time after optical excitation, topt, to be experimentally mapped. The wide range photon energies available from current ultrashort pulse sources can excite carriers from the valence band to the conduction band of semiconductors as well as materials that are insulators at room temperature. A good example of these measurements is optical pump THz probe spectroscopy of sapphire,46 a material typically considered an outstanding insulator with a dielectric strength of nearly 5 × 106 Vm–1, resistivity over 1014 Ω-cm and a bandgap of 8.7 eV. To excite carriers, an amplified Ti:Al2O3 laser pulse with photon energy of 1.5 eV was frequency tripled
7525_C001.indd 34
11/19/07 10:59:42 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
35
to 4.5 eV and two photon absorption moved electrons from the valence to the conduction band. The transmitted THz pulse showed the carriers behaved according to the Drude theory and had strongly temperature-dependent mobility that could be as high as µ = 3 × 104 cm2v–1s–1 at low temperatures when the scattering of the carriers by phonons (lattice vibrations) was reduced. In chemistry, optical pump THz probe measurements have been used to measure solvation dynamics in liquids, critical to many aspects of liquid-phase chemistry including the growth and self-assembly of nanostructures. Because the reorientation of the solvent occurs on time scales of 0.1–10 ps, THz frequencies are useful for probing these systems. In one set of measurements,47 the optical pulse was used to excite a solvated dye molecule and the reorientation of the solvent molecule dipole moments surrounding the optically excited dye molecule was measured with the THz pulse. Another example of optical pump THz probe spectroscopy is measurement in superconducting materials. In the previous example, the optical pulse caused conductivity changes by creating charge carriers; in the prototypical high Tc superconductor, YBCO short-pulse optical excitation breaks superconducting pairs.48 The pair breaking causes transient changes in the complex conductivity and the recovery time of the superconducting pairs can be determined by using a THz probe to measure the conductivity as a function of delay between the optical excitation pulse and the THz pulse. These measurements are only a representative fraction of the physical systems that have been examined to date with optical pump THz probe spectroscopy; more detailed discussion is found in later chapters. It is not necessary to use photoconductively generated THz pulses in reflection or transmission for spectroscopic measurements. Because the dynamics of the photogenerated carriers in the THz source determine the temporal profile of THz pulse, the generated pulse itself can provide information on carrier dynamics on a subpicosecond time scale and can be used for spectroscopic measurements. Using the generated pulse itself for spectroscopic measurement is known as THz emission spectroscopy and a simplified experimental configuration is illustrated in Figure 1.19. THz emission spectroscopy provides fundamentally different information than optical pump-probe spectroscopy. Optical techniques generally give insight into the dynamics of how carriers evolve in energy, the vertical axis on an E versus k diagram.
Delay
Sample
fs Laser
Figure 1.19 Experimental configuration of THz emission spectroscopy.
7525_C001.indd 35
11/19/07 10:59:44 AM
36
Terahertz Spectroscopy: Principles and Applications
THz emission spectroscopy, in contrast, probes the velocity, or momentum, evolution of carriers in time. Photoconductively generated THz pulses have electric fields proportional to the rate of change of the current, E(t) ∝ δJ/δt. Because the current is proportional to carrier density and velocity, J = N(t)ev(t), the THz field strength is proportional to the dynamic velocity ensemble of the carriers. For example, the rising edge of the THz pulse arises from carrier acceleration in conjunction with an increasing number of carriers because of optical excitation. The peak of the THz pulse occurs when the carrier ensemble is undergoing the maximum acceleration. The THz field then decreases and has a zero crossing when the ensemble velocity is a maximum (δv/δt = 0). Accurately extracting relevant information on carrier dynamics using THz emission spectroscopy requires the ability to accurately measure the electric field profile. Because the pulse shape is affected by the detector bandwidth, dispersion effects, and propagation, it is important to account for these effects of the measurement system to avoid experimental artifacts. Because THz emission spectroscopy is sensitive to the motion carriers with excess energy from photoexcitation in accelerating fields, it provides information on the dynamics of hot carriers. The ability to study hot carrier transport processes in high fields has impact on the development of high speed semiconductor devices such as high-electron mobility transistors. The THz pulse shape depends on both acceleration and collisions of carriers, so the pulse profile provides insight into carrier scattering processes including collisions with impurities and dopants, interaction with phonons (quantized lattice vibrations), and scattering from other carriers. It is possible to generate THz radiation from most semiconductors so that THz emission spectroscopy can measure the hot carrier dynamics in semiconductor materials without requiring direct electrical contact. It is straightforward to create heterostructures or lithographically define structures so that conditions such as temperature, the electrical bias, or the optical excitation density can be probed to map out carrier dynamics over a large parameter space. Similarly, by tuning the optical excitation wavelength, the dynamics of carriers created at different energies in the conduction band can be experimentally probed by looking at how the shape of the generated THz pulse changes. Even states below the conduction band, the so-called Urbach tail, can be investigated. THz emission spectroscopy directly measure Bloch oscillations in semiconductors. Bloch oscillations are changes in electron energy along with an oscillatory motion in real space that result from motion in the periodic crystal potential and were first predicted by Zener in 1934 based on Bloch’s 1928 theory of electrons in a periodic band structure.49 Much of the interest in Bloch oscillations arises from their potential to produce powerful, tunable sources of radiation from the oscillatory motion of the electrons. Because electron scattering processes are usually much faster than the period of the Bloch oscillation, dephasing processes need to be controlled. The development of controllable band structures in semiconductor superlattices allowed materials to be created in which Bloch oscillations could be observed. THz emission spectroscopy directly observes Bloch oscillations as oscillations following the initial THz pulse. As the bias on the sample increases, so does the frequency of the Bloch oscillations, as does the spectrum of the emitted THz radiation.
7525_C001.indd 36
11/19/07 10:59:45 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
37
Any other process that gives emits a THz pulse is a candidate for THz emission spectroscopy; examples are carrier acceleration in the surface depletion field of a semiconductor50 and emission from metal-air surfaces from optical rectification.51 THz emission spectroscopy is not limited to crystalline semiconductors because many materials produce a transient polarization after optical excitation. Emission from semiconducting polymer materials has helped to clarify the process of charge generation in these materials. Work has also looked at magnetic nonlinearities as well as electronic nonlinearities.48 Some of the more novel work on THz emission spectroscopy has been done on polar molecules in liquids. In these experiments, a static electric field is placed across the liquid, and the polar molecules orient in the field. Orientation of the ensemble is required to generate THz radiation because the net dipole moment of an ensemble of randomly aligned molecules will be zero. When the molecules are photoexcited, they undergo intermolecular charge transfer on a picosecond time scale, which causes a change in the dipole moment and a transient polarization of the ensemble of molecules that emits a THz pulse. These measurements provide information on the time scale and direction of intermolecular charge transfer.47
References 1. Harnessing light: optical science and engineering in the 21st century. Washington, D. C.: National Academy Press, 1998. 2. M. Inguscio et al., A review of frequency measurements of optically pumped lasers from 0.1 to 8 Thz, J. Appl. Phys., 60, R161, 1986. 3. D. S. Kurtz, et al., Submillimeter-wave sideband generation using Varactor Schottky diodes, IEEE Trans. Microwave Theory Tech., 50, 2610, 2002. 4. A. Tredicucci, et al., Terahertz quantum cascade lasers—first demonstration and novel concepts, Semicond Sci Technol, 20, S222, 2005. 5. S. D. Ganichev and W. Prettle, Intense THz excitation of semiconductors. New York: Oxford University Press, 2006. 6. C. Meystre and M. Sargent III, Elements of quantum optics. Berlin: Springer-Verlag, 1991. 7. Y. R. Shen, The principles of nonlinear optics. Hoboken, N. J.: John Wiley & Sons, 2003. 8. L. Allen and J. H. Eberly, Optical resonance and two-level atoms. New York: John Wiley & Sons, 1975. 9. S. R. Keiding and D. Grischkowsky, Measurements of the phase shift and reshaping of terahertz pulses due to total internal reflection, Opt. Lett., 15, 48, 1990. 10. S. Feng, H. G. Winful, and R. W. Hellwarth, Gouy shift and temporal reshaping of focused single-cycle electromagnetic pulses, Opt. Lett., 23, 385, 1998. 11. P. U. Jepsen, R. H. Jacobsen, and S. R. Keiding, Generation and detection of terahertz pulses from biased semiconductor antennas, J. Opt. Soc. Am. B, 13, 2424, 1996. 12. K. Bock, H. L. Hartnagel, and J. Dumas, Surface induced electromigration in GaAs devices, in Reliability of gallium arsenide MMICs, A. Christou, ed. New York: John Wiley & Sons, 1992, 192. 13. C. A. Balanis, Advanced engineering electromagnetics. New York: John Wiley & Sons, 1989. 14. R. W. P. King and G. S. Smith, Antennas in matter. Cambridge: MIT Press, 1981. 15. K. Liu, et al., Terahertz radiation from InAs induced by carrier diffusion and drift, Phys. Rev. B, 73, 2006.
7525_C001.indd 37
11/19/07 10:59:46 AM
38
Terahertz Spectroscopy: Principles and Applications 16. S. D. Benjamin, H. S. Loka, and P. W. E. Smith, Tailoring of low-temperature MBE-grown GaAs for ultrafast photonic devices, Can. J. Phys., 74, S68, 1996. 17. F. E. Doany, D. Grischkowsky, and C.-C. Chi, Carrier lifetime versus ion-implantation dose in silicon on sapphire, Appl. Phys. Lett., 50, 462, 1987. 18. D. R. Dykaar, et al., Log-periodic antennas for pulsed terahertz radiation, Appl. Phys. Lett., 59, 262, 1991. 19. H. Murakami, et al., Tetrahertz pulse radiation properties of a Bi2Sr2CaCu2O8 + delta bowtie antenna by optical pulse illumination, Jap. J. Appl. Phys. Part 1, 41, 1992, 2002. 20. H. Harde, R. A. Cheville, and D. Grischkowsky, Terahertz studies of collision-broadened rotational lines, J. Phys. Chem. A, 101, 3646, 1997. 21. M. Born and E. Wolf, Principles of optics, ed 7. New York: Cambridge University Press, 1999. 22. L. Duvillaret, F. Garet, and J. L. Coutaz, A reliable method for extraction of material parameters in terahertz time-domain spectroscopy, IEEE J. Selected Topics Quantum Electr., 2, 739, 1996. 23. M. T. Reiten, et al. Incidence-angle selection and spatial reshaping of terahertz pulses in optical tunneling, Opt. Lett., 26, 1900, 2001. 24. L. Duvillaret, F. Garet, and J. L. Coutaz, Highly precise determination of optical constants and sample thickness in terahertz time-domain spectroscopy, Appl. Opt., 38, 409, 1999. 25. P. U. Jepsen and B. M. Fischer, Dynamic range in terahertz time-domain transmission and reflection spectroscopy, Opt. Lett., 30, 29, 2005. 26. S. C. Howells, S. D. Herrera, and L. A. Schlie, Infrared wavelength and temperature dependence of optically induced terahertz radiation from InSb, Appl. Phys. Lett., 65, 2946, 1994. 27. G. Zhao, et al., Design and performance of a THz emission and detection setup based on a semi-insulating GaAs emitter, Rev. Sci. Instr., 73, 1715, 2002. 28. W. H. Press, et al., Numerical recipes in Fortran, 2nd ed., New York: Cambridge University Press, 1993. 29. W. Lukosz and Z. S. Eth, Light emission by magnetic and electric dipoles close to a plane dielectric interface. III. Radiation patterns of dipoles with arbitrary orientation, J. Opt. Soc. Am., 69, 1495, 1979. 30. M. T. Reiten, S. A. Harmon, and R. A. Cheville, Terahertz beam propagation measured through three-dimensional amplitude profile determination, J. Opt. Soc. Am. B, 20, 2003. 31. A. E. Siegman, Lasers. Mill Valley: University Science Books, 1986. 32. J. C. G. LeSurf, Millimetre-wave optics, devices, and systems. Bristol: Adam Hilger, 1990. 33. D. M. Mittleman, R. H. Jacobsen, and M. C. Nuss, T-ray imaging, IEEE J. Sel. Topics Quantum Electr, 2, 679, 1996. 34. G. Gallot, et al., Terahertz waveguides, J. Opt. Soc. Am. B, 17, 851, 2000. 35. D. Grischkowsky, et al., Far-infrared time-domain spectroscopy with terahertz beams of dielectrics and semiconductors, J. Opt. Soc. Am. B, 7, 2006, 1990. 36. Z. P. Jiang, M. Li, and X. C. Zhang, Dielectric constant measurement of thin films by differential time-domain spectroscopy, Appl. Phys. Lett., 76, 3221, 2000. 37. K. S. Lee, T. M. Lu, and X. C. Zhang, The measurement of the dielectric and optical properties of nano thin films by THz differential time-domain spectroscopy, Microelectr J, 34, 63, 2003. 38. S. P. Mickan, et al., Double modulated differential THz-TDS for thin film dielectric characterization, Microelectr J, 33, 1033, 2002.
7525_C001.indd 38
11/19/07 10:59:47 AM
Terahertz Time-Domain Spectroscopy with Photoconductive Antennas
39
39. M. Brucherseifer, P. H. Bolivar, and H. Kurz, Combined optical and spatial modulation THz-spectroscopy for the analysis of thin-layered systems, Appl. Phys. Lett., 81, 1791, 2002. 40. J. L. Johnson, T. D. Dorney, and D. M. Mittleman, Enhanced depth resolution is terahertz imaging using phase shift interferometry, Appl. Phys. Lett., 78, 835, 2001. 41. S. Krishnamurthy, et al., Characterization of thin polymer films using terahertz time-domain interferometry, Appl. Phys. Lett., 79, 875, 2001. 42. J. A. Small and R. A. Cheville, Measurement and noise characterization of optically induced index changes using terahertz interferometry, Appl. Phys. Lett., 84, 4328, 2004. 43. D. Guenther, Modern optics, 2nd ed., New York: John Wiley & Sons, 1990. 44. T. Nagashima and M. Hangyo, Measurement of complex optical constants of a highly doped Si wafer using terahertz ellipsometry, Appl. Phys. Lett., 79, 3917, 2001. 45. M. Li, et al., Time-domain dielectric constant measurement of thin film in GHz-THz frequency range near the Brewster angle, Appl. Phys. Lett., 74, 2113, 1999. 46. J. Shan, et al., Measurement of the frequency-dependent conductivity in sapphire, Phys. Rev. Lett., 90, 247401, 2003. 47. M. C. Beard, G. M. Turner, and C. A. Schmuttenmaer, Terahertz spectroscopy, J. Phys. Chem. B, 106, 7146, 2002. 48. D. J. Hilton, e. al., On photo-induced phenomena in complex materials: probing quasi- particle dynamics using infrared and far-infrared pulses, J. Phys. Soc. Japan, 75, 011006, 2006. 49. K. Leo, Interband optical investigation of Bloch oscillations in semiconductor superlattices, Semicond Sci Technol, 13, 249, 1998. 50. J. Darmo, et al., Surface-modified GaAs terahertz plasmon emitter, Appl. Phys. Lett., 81, 871, 2002. 51. F. Kadlec, P. Kuzel, and J. L. Coutaz, Study of terahertz radiation generated by optical rectification on thin gold films, Opt. Lett., 30, 1402, 2005.
7525_C001.indd 39
11/19/07 10:59:48 AM
7525_C001.indd 40
11/19/07 10:59:48 AM
2
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection—Optical Rectification and Electrooptic Sampling Ingrid Wilke and Suranjana Sengupta Rensselaer Polytechnic Institute
Contents 2.1
Introduction.................................................................................................... 42 2.1.1 Terahertz Time-Domain Spectroscopy: An Overview....................... 42 2.2 Optical Rectification and Linear Electrooptic Effect....................................44 2.3 Experimental Results of Terahertz-Frequency Radiation Generation by Optical Rectification of Femtosecond Laser Pulses................................. 49 2.3.1 Materials............................................................................................. 50 2.3.1.1 Semiconductors..................................................................... 50 2.3.1.2 Inorganic Electrooptic Crystals............................................ 52 2.3.1.3 Organic Electrooptic Crystals............................................... 52 2.3.2 Recent Developments.......................................................................... 56 2.4 Experimental Results of Terahertz Electrooptic Detection........................... 57 2.4.1 Materials............................................................................................. 57 2.4.1.1 Semiconductors and Inorganic Crystals................................ 57 2.4.1.2 Organic Crystals....................................................................64 2.5 Application of Electrooptic Sampling of Terahertz Electric Field Transients....................................................................................................... 65 References................................................................................................................. 69
41
7525_C002.indd 41
11/15/07 10:46:38 AM
42
Terahertz Spectroscopy: Principles and Applications
2.1 Introduction The generation and detection of short pulses of terahertz (THz) frequency electromagnetic radiation are attracting great interest. Research activities in this area are driven by applications of THz-frequency radiation pulses in time-domain THz spectroscopy and time-domain THz imaging.1,2 Recent examples of major scientific advancements in THz wave research include the detection of single-base pair differences in femtomolar concentrations of DNA,3 the observation of the temporal evolution of exciton formation in semiconductors4 and understanding of carrier dynamics in high-temperature superconductors.5 Real-world applications of time-domain THz spectroscopy and imaging address important problems such as nondestructive testing,6 as well as new approaches to medical diagnostics and rapid screening in drug development.7 One of the research directions in THz science and technology is to increase the bandwidth of short THz-frequency radiation pulses. Nonlinear optical phenomena such as optical rectification and the linear electrooptic effect (Pockels’ effect) are attractive options for broadband generation and detection of THz radiation. This chapter provides an overview of the generation and detection of freely propagating THz pulses based on nonlinear optical techniques. In Section 2.1.1 of this chapter, the principles of time-domain THz spectroscopy and time-domain THz imaging using nonlinear optical techniques for THz pulse generation and detection are briefly discussed. Section 2.2 describes the principles of generation and detection of THz-frequency radiation by optical rectification of femtosecond laser pulses and femtosecond electrooptic sampling. THz radiation emission has been reported from a variety of nonlinear materials such as lithium niobate (LiNbO3),8,9 lithium tantalate (LiTaO3),9,10 zinc telluride (ZnTe),11,12 indium phosphide (InP),13 gallium arsenide (GaAs),14 gallium selenide (GaSe),15,16 cadmium telluride (CdTe),17 cadmium zinc telluride (CdZnTe),18 DAST,10,19 and metals.20,21 Section 2.3 summarizes the performance of THz emitters based on these materials in terms of bandwidth and signal strength of the emitted THz radiation. Materials for the detection of THz radiation by femtosecond electrooptic sampling are the subjects of Section 2.4. In Section 2.5, an application of electrooptic detection of THz-frequency electromagnetic transients is discussed.
2.1.1 Terahertz Time-Domain Spectroscopy: An Overview The basic ideas of time-domain THz spectroscopy and a time-domain THz imaging system is illustrated in Figure 2.1. A subpicosecond pulse of THz-frequency electromagnetic radiation passes through a sample placed in the THz beam and its time profile is compared to a reference pulse. The latter can be a freely propagating pulse or a pulse propagating through a medium with known properties. The frequency spectra of the transmitted and reference THz radiation pulses are obtained by Fourier transformation. Analysis of the frequency spectra yields spectroscopic information on the material under investigation. In the case of time-domain THz imaging the THz radiation focal spot is scanned across the sample and a THz image of the object under investigation is obtained. The time-domain THz spectroscopy system shown in Figure 2.1 is powered by a laser, which emits a train of femtosecond duration pulses at near-infrared frequencies.
7525_C002.indd 42
11/15/07 10:46:39 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 43 Delay Stage M1
Laser
M2
Probe Beam Beam Splitter
M5
PM I
PM II
Pump Beam
THz Beam PBS
Chopper
Emitter
L2
Detector
L1 M3
M6
Quarter Wave Plate
M4
M7 Data Acquisition Software
Lock-in Amplifier
Diodes
Wollaston Prism
Figure 2.1 Experimental arrangements for time-domain THz spectroscopy measurements using nonlinear optical techniques for the generation and detection of freely propagating THz-radiation pulses. (M1–M7 optical beam steering mirrors, PMI, PMII parabolical THzbeam steering mirrors, L1, L2 lenses).
The initial laser beam after passing through a beam splitter is split into two parts: the pump and the probe beam. The pump beam after being modulated by an optical chopper is focused on the THz emitter (a second-order nonlinear optical medium), which releases a subpicosecond pulse of THz radiation in response to the incident femtosecond near infrared laser pulse. The generated THz radiation is focused onto a detector using two off-axis parabolic mirrors. The detector is an electrooptic crystal. The probe beam gates the detector, whose response is proportional to the amplitude and sign of the electric field of the THz pulse. By changing the time delay between the pump and the probe beams by means of an optical delay stage, the entire time profile of the THz transient can be traced. Electrooptic detection of THz transients is possible when the THz radiation pulse and the probe beams coincide in a copropagating geometry inside the electrooptic crystal. A pellicle beam splitter is put in the THz beam line for this purpose. As the THz pulse and probe beam copropagate through the electrooptic crystal, a phase modulation is induced on the probe beam which depends on the electric field of the THz radiation. The phase modulation of the probe beam is analyzed by a quarter wave (l/4) plate and the beam is then split into two beams of orthogonal
7525_C002.indd 43
11/15/07 10:46:41 AM
44
Terahertz Spectroscopy: Principles and Applications
polarizations by a Wollaston prism. At this point, the phase modulation of the probe beam is converted to an intensity modulation of the two orthogonal polarizations of the probe beam, which are then steered into a pair of photodiodes. A lock-in amplifier subsequently detects the difference in probe laser light intensities measured by the photodiodes. Next, the key aspects of the nonlinear optical processes involved in the generation and detection of short pulses of THz-frequency radiation are discussed in depth.
2.2 Optical Rectification and Linear Electrooptic Effect Optical rectification and the linear electrooptic effect (Pockels’ effect) are nonlinear optical techniques for the generation and detection of freely propagating subpicosecond THz-frequency radiation pulses. Generally, optical rectification refers to the development of a DC or low- frequency polarization when intense laser beams propagate through a crystal. The linear electrooptic effect describes a change of polarization of a crystal from an applied electric field. Optical rectification and the linear electrooptic effect occur only in crystals that are not centrosymmetric. However, optical rectification of laser light by centrosymmetric crystals is possible if the symmetry is broken by a strong electric field. Furthermore, generation and detection of THz-radiation pulses by optical rectification and the Pockels’ effect require that the crystals are sufficiently transparent at THz and optical frequencies. Freely propagating subpicosecond THz-radiation pulses are generated by optical rectification of femtosecond (fs) near infrared laser pulses in crystals with appropriate nonlinear optical properties for this process. The detection of freely propagating THz-radiation pulses is performed by measuring the phase modulation of an fs near infrared laser pulse propagating through an electrooptic crystal simultaneously with a THz-radiation pulse. The electric field of the THz radiation induces a phase modulation of the fs laser pulse through the linear electrooptic effect. In the following section, the theory of optical rectification and the linear electrooptic effect is discussed. The discussion of theory is limited to material we consider useful for the reader to get a general idea of the underlying physics of THz pulse generation and detection by nonlinear optical techniques and to equations that are relevant to the implementation of the techniques in the laboratory. Our discussion mainly follows the original work by pioneers in the field. First, DC optical rectification of 694 nm continuous-wave laser radiation in potassium dihydrogen phosphate and potassium dideuterium phosphate was demonstrated experimentally by Bass et al. in 1962.22 After that, monochromatic THz- radiation generation at 3 THz by low-difference frequency mixing of near-infrared (nir) laser radiation (lnir = 1.059–1.073 Nm) in quartz was achieved in 1965 by Zernike and Berman.23 Yang et al. demonstrated generation of broadband (0.06–0.36 THz) freely propagating THz-radiation pulses by optical rectification of picosecond Nd: glass laser pulses in LiNbO3 in 1971.8 Eventually, Hu et al. produced free-space THz-frequency radiation with a bandwidth of 1 THz by optical rectification of femtosecond CPM dye laser pulses in LiNbO3 in 1990.10
7525_C002.indd 44
11/15/07 10:46:42 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 45
In 1893, Friedrich Pockels discovered the linear electrooptic effect.24 Subsequently, the phase modulation of optical laser light at microwave frequencies using the linear electrooptic effect was demonstrated in 1962 by Harris et al.25 Then, Valdmanis and coworkers built the first electrooptic sampling system with picosecond resolution for the measurements of ultrafast electrical transients in 1982.26 Finally, electrooptic sampling of freely propagating THz-radiation pulses was demonstrated in 1995 by Wu and Zhang27 and in 1996 by Jepsen et al.28 and Nahata et al.29 An excellent description of laser light modulation based on the linear electrooptic effect is given by Yariv.30 Rigorous quantum mechanical calculations of optical rectification were carried out by Armstrong et al.31 Previous reviews of nonlinear generation and detection of sub-picosecond THz-radiation pulses were published by Bonvalent and Joffre,32 Shen et al.,33 and Jiang and Zhang.34 The discussions of optical rectification and the Pockels’ effect begin by considering scalar relationships of polarization P, electric susceptibility, and electric field E.35 P = c( E ) E
(2.1)
The electric polarization P of a material is proportional to the applied electric field E. Here, c(E) is the electric susceptibility. The nonlinear optical properties of the material are described by expanding c(E) in powers of the field E.
P = ( c1 + c 2 E + c3 E 2 + c 4 E 3 + ) E
(2.2)
Optical rectification and the linear electrooptic effect are second order nonlinear optical effects P2nl and described by the P2nl = c2 E2 term in the expansion. For example, consider an optical electric field E described by E = E 0 cos wt. In this case, the second-order nonlinear polarization P2nl consists of a dc polarization c2 E 02/2 and a polarization with a cos 2wt dependence.
P2nl = c 2 E 2 = c 2
E0 2 (1 + cos 2 w t ) 2
(2.3)
The DC polarization results from the rectification of the incident optical electric field by the second-order nonlinear electric susceptibility of the material. The polarization with the cos 2wt dependence describes second harmonic generation. This nonlinear optical process is not relevant to the generation and detection of THz radiation by nonlinear optical techniques and therefore not discussed further. Similarly, consider two optical fields oscillating at frequencies E1 = E 0cos w1t and E2 = E 0cos w2t. P2nl = c 2 E1 E2 = c 2
E0 2 [cos(w1 - w 2 )t + cos(w1 + w 2 )t ] 2
(2.4)
this case, the DC second-order nonlinear polarization P2nl consists of a term In P2w1-w2 proportional to the difference frequency w1 + w2 and a term P2w1+w2 proportional to the sum frequency w1 + w2. The production of THz radiation by optical rectification relies on low difference frequency generation and is described by the
7525_C002.indd 45
11/15/07 10:46:47 AM
46
Terahertz Spectroscopy: Principles and Applications
term P2w1 - w2. Again, sum frequency generation P2w1 + w2 is not relevant to generation of THz radiation by nonlinear optical techniques. In the same way, generation of THz-radiation pulses from optical rectification of fs laser pulses is based on difference frequency mixing of all frequencies within the bandwidth Dw of an fs near infrared laser pulse. Specifically, an fs pulse ∆t is characterized by a large frequency bandwidth Dw. The bandwidth of the laser pulse is described by a Gauss function of width 1/4G.36 ( w - w 0 )2 E (w ) ∝ exp 4G
(2.5)
In the time domain, the fs laser pulse is described by an optical field oscillating at frequency w0 with a time dependence described by a Gauss function.
E (t ) = E0 exp (iw 0t ) exp( - Gt 2 )
(2.6)
The bandwidth of the THz-radiation pulse is determined by difference frequency generation by all frequencies within the bandwidth of the fs laser pulse. The time profile of the radiated THz pulse from optical rectification of the fs laser pulse is proportional to the second time derivative of the difference frequency term P2w1 - w2. The time dependence of P2w1 - w2 is determined by the Gaussian time profile of the optical laser pulse. The physics of the linear electrooptic effect is described by the same term P2n1 = 2 c2 E in the expansion of c(E) as optical rectification. To understand the relationship between optical rectification and the Pockels’ effect, it is now necessary to describe polarization P and electric field E by vectors and the susceptibility c by a third rank tensor. Quantum mechanical calculations of the polarization for the case of two laser beams with frequencies w2 , w1 present in a crystal demonstrate that the ith component of the second-order nonlinear polarization piw1-w2 is related to the components j and k of the electrical fields Ejw1 and Ekw2 via the susceptibility tensor component cijkw1 - w2 35 w1 - w 2
w1
w2
pi = c ijk E j Ek (2.7) DC optical rectification and the linear electrooptic effect result from Equation 2.7 considering the limits of w2 - > w1 and w2 - > 0, respectively.
w1 - w 2
w 2 → w1
pi0 = c ijk0 E wj 1 Ekw1
(2.8)
w2 → 0
piw1 = c ijkw1 E wj 1 Ek0
(2.9)
Equations 2.8 and 2.9 demonstrate that a strong electric field at frequency w1 gives rise to a dc polarization pi0 and a DC electric field Ek 0 changes the polarization piw1 at frequency w1.
7525_C002.indd 46
11/15/07 10:46:52 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 47
Further calculations demonstrate that c 0ijk is equal to c w1jik. Therefore, the third rank tensors are identical under simple interchange of indices as well as frequencies. This demonstrates the identity of optical rectification and the linear electrooptic effect. As a result of this identity, it is possible to estimate the magnitude of optical rectification from the linear electrooptic coefficients of a material. The most widely employed crystals for nonlinear optical generation and detection of THz radiation are ZnTe, gallium phosphide (GaP), and GaSe. ZnTe and GaP exhibit zincblende structure and 43m point group symmetry. GaSe is a hexagonal crystal with 62m point group symmetry. All three crystals are uniaxial. Uniaxial crystals have only one axis of rotational symmetry referred to as the c-axis or optical axis of the crystal. The efficacy of ZnTe, GaP, and GaSe for nonlinear optical THz generation and detection is rated by the linear electrooptic coefficient of the materials. The linear electroptic coefficients for ZnTe, GaP, and GaSe are listed in Table 2.1. The relationship between susceptibility tensor elements describing optical rectification cijk 0 and linear electrooptic effect c jik w is: cijk 0 + cikj 0 =
1 c jik w 2
(2.10)
and the relationship between the linear electrooptic coefficient rjki and the linear electrooptic effect tensor element c jik w is: 4p rjki = - 2 2 c jik w n0 ne
(2.11)
Efficient generation and detection of THz radiation by optical rectification and the Pockels’ effect require single crystals with high second-order nonlinearity or large electrooptic coefficients, proper crystal thickness and proper crystal orientation with respect to the linear polarization of the THz radiation. The surfaces of the crystals should be optically flat at the laser excitation wavelengths and of high crystalline quality (e.g., low levels of impurities, structural defects, and intrinsic stress). The bandwidth of an electrooptic crystal for THz generation and detection is determined by the coherence lengths and optical phonon resonances in the material.
Table 2.1 Electrooptic Coefficients of Some Commonly Used Terahertz Emitters and Detectors Material ZnTe GaP GaSe
7525_C002.indd 47
Structure Zincblende(30) Zincblende(30) Hexagonal (53)
Point Group Symmetry ( 30 )
43m 43m( 30 ) 62 m( 30 )
Electrooptic Coefficient (pm/V) r41 = 3.9(30) r41 = 0.97(30) r41 = 14.4(76)
11/15/07 10:46:59 AM
48
Terahertz Spectroscopy: Principles and Applications
Infrared active optical phonon resonances result in strong absorption of electromagnetic radiation at the absorption frequencies. The phonon absorption bands (optical phonons) of a material in the THz frequency range are not available for THz generation and detection. If the refractive indices of the near infrared laser excitation frequency and the THz radiation are identical, then the bandwidths of the THz radiation depend only on the pulse width of the incident femtosecond near infrared laser beam. Furthermore, the strength of emission and sensitivity of THz detection would increase similarly for all frequencies within the bandwidth with increasing crystal thickness. However, the refractive indices for the near infrared laser frequency and THz frequency are generally not identical. Consequently, electromagnetic waves at THz and near infrared frequencies travel at slightly different speeds through the crystal. The efficacy of nonlinear optical THz generation and detection decreases if the mismatch between the velocities becomes too large. The distance over which the slight velocity mismatch can be tolerated is called the coherence length. As a result, efficient THz generation and detection at a given frequency only occur for crystals that are equal in thickness or thinner than the coherence length for this frequency. The coherence length in case of pulsed near-infrared laser radiation is defined as:11 lc (w THz ) =
w THz
pc | nopt eff (w 0 ) - nTHz (w THz ) |
(2.12)
with ∂nopt nopt eff = nopt (w ) - l opt ∂l l
(2.13) opt
In Equations 2.12 and 2.13, c is the velocity of light, w = 2p/u the THz freTHz THz quency, w0 is the near infrared excitation frequency nTHz the refractive index at THz frequencies, nopt the index of refraction at near infrared wavelength lopt, and nopt eff the group velocity refractive indices of the femtosecond near infrared laser pulse. THz emission strength of a crystal and sensitivity of an electrooptic THz detector are proportional to the thickness of the crystal. However, the bandwidth of the THz emitter crystal and bandwidth of the THz detector crystal also depend on the crystal thickness. Generally THz emission strength and THz emission bandwidth for a crystal have a reciprocal relationship. The THz emission bandwidth increases when the crystal becomes thinner. The THz emission strength decreases when the crystal becomes thinner. The same rule applies to the sensitivity of an electrooptic THz detector and the detector bandwidth. Thinner crystals have a higher bandwidth but lower sensitivity than thicker crystals and vice versa. For efficient generation of THz radiation by optical rectification of femtosecond laser pulses from zincblende structure crystals, it is important to select the proper orientation of the crystal with respect to the linear polarization of the laser beam. The preferred crystal orientations of selected materials are discussed in Sections 2.3 and 2.4.
7525_C002.indd 48
11/15/07 10:47:01 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 49
In case of the longitudinal linear electrooptic effect, the electric field is applied parallel to the direction of propagation of the optical probe laser beam. In case of the transverse linear electrooptic effect, the electric field is applied perpendicular to the direction of propagation of the optical probe beam. Detection of THz radiation pulses is generally performed using the geometry of the transverse electrooptic effect. The amplitude and phase of the subpicosecond THz-radiation pulse are measured by recording the phase change of femtosecond near infrared laser pulses traveling collinearly and simultaneously with the THz radiation pulses through the electrooptic crystal. The electric field of the THz radiation induces a change of the index of refraction of the crystal via the linear electrooptic effect such that the material becomes birefringent. The phase retardation G between the ordinary and extraordinary ray after propagating through the birefringent crystal is proportional to the amplitude and phase of the THz electric field E, the crystal thickness l, the linear electrooptic coefficient r14, the index of refraction of the crystal at the near infrared laser frequency no, and the near-infrared wavelength l.30 G∝
1 3 ln0 r41ETHz l
(2.14)
Furthermore, the phase retardation also depends on the orientation of the crystal and directions of polarization of the THz radiation pulse and the near infrared laser pulse.37 For 43m zincblende structure crystals, preferred directions of the THz electric field ETHz, optical field Eopt, and crystal orientation are discussed in Sections 2.3 and 2.4. The temporal profile of the THz radiation is mapped out in time by delaying the much shorter femtosecond near infrared laser pulse with respect to the THz radiation pulse and measuring the phase retardation as a function of the delay between THz radiation pulse and optical probe pulse.
2.3 ExperimenTAL Results of Terahertz-Frequency Radiation Generation by Optical Rectification of Femtosecond Laser Pulses In this chapter, we review the experimental results for generation of THz radiation pulses based on optical rectification. Several nonlinear optical materials have been reported to generate THz radiation by optical rectification of a femtosecond near infrared laser pulse. Table 2.2 lists the various crystals investigated for generation of THz radiation by optical rectification. For the sake of organization, the experimental results will be divided into three broad material categories: semiconductors, inorganic electrooptic crystals and organic electrooptic crystals, and the characteristics of the emitted THz radiation will be discussed in brief under each material category. The performance of various emitters will be discussed on the basis of bandwidth and amplitude of the emitted THz radiation. We conclude our discussion by presenting recent experimental developments in THz emitter research.
7525_C002.indd 49
11/15/07 10:47:03 AM
50
Terahertz Spectroscopy: Principles and Applications
Table 2.2 Materials Used for Generation of Terahertz Optical Rectification Semiconductors
Inorganic Electrooptic Crystals
Organic Electrooptic Crystals
LiNbO3 LiTaO3
4-N-methylstilbazolium tosylate (DAST) N-benzyl-2-methyl-4-nitroaniline (BNA) (-) 2-(a-methylbenzyl-amino)- 5-nitropyridine (MBANP) electrooptic polymers
GaAs InP CdTe InAs InSb GaP ZnTe ZnCdTe GaSe
2.3.1 Materials 2.3.1.1 Semiconductors A significant amount of research dating back as early as the 1970s has explored the generation of THz radiation by optical rectification of pico- and femtosecond optical pulses in nonlinear optical crystals. Experimental work in the early 1990s reported that THz-frequency radiation could also be generated by femtosecond optical pulses incident on a semiconductor surface.38,39 This observation was initially explained as the dipole radiation of a time-varying current resulting from photo-excited charge carriers in the depletion field near the semiconductor surface.39–41 Although the ultrafast photocarrier transport model successfully explained the transverse magnetic polarization of the emitted THz radiation and the observed emission maxima for Brewster angle incidence, the intensity modulation of the emitted THz radiation observed when the crystal was rotated about its surface normal indicated that there was more than one mechanism responsible for the generation of THz radiation. In 1992, Chuang et al.42,43 proposed a theoretical model based on optical rectification of femtosecond laser pulses at semiconductor surfaces, which successfully explained all of the earlier experimental observations. The investigation of the physics of optical rectification indicates that depending on the optical fluence, the THz radiation generation by optical rectification is either a second-order nonlinear optical process governed by the bulk second-order susceptibility tensor c2, or a third-order nonlinear optical process whereby a second-order nonlinear susceptibility results from the mixing of a static surface depletion field and the third-order nonlinear susceptibility tensor c3.41,44 THz radiation generation from optical rectification of femtosecond laser pulses has been reported from <100>, <110>, and <111>-oriented crystals with zincblende structure commonly displayed by most III–V (and some II–VI) semiconductors. These crystals have a cubic structure with 43m point group symmetry and only one independent nonlinear optical coefficient, namely r41 = r52 = r63.30 Theory predicts that for <100>-oriented zincblende crystals, there is no optical rectification field at normal incidence (as the nonvanishing second-order optical coefficients r41, r52, and
7525_C002.indd 50
11/15/07 10:47:05 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 51
r63 are not involved), whereas a three-fold rotation symmetry about the surface normal may be observed for <110> and <111> orientations. Experimental studies conducted on <100>, <110>, and <111> oriented GaAs, CdTe, and indium phosphide (InP) crystals13,17,41 and <110> GaP crystal45 are in excellent agreement with the theoretical results providing evidence that second-order bulk optical rectification is the major nonlinear process under the condition of moderate optical fluence (~nJ/cm2) and normal incidence on unbiased semiconductors. A dramatic variation in the radiated THz signal along with polarity reversal is observed in <110> and <111> CdTe and GaAs crystals, as the incident photon energy is tuned near the bandgap.13,17,41 This phenomenon can be explained as the dispersion of the nonlinear susceptibility tensor near the electron resonance state.13,41 THz generation by optical rectification has recently also been reported from narrow bandgap semiconductors such as indium arsenide (InAs) and indium antimonide (InSb) at high optical fluence (1–2 mJ/cm2) and off-normal incidence.44,46–50 Experimental results of THz emission from <100> InSb crystal and <100>, <110>, and <111> InAs crystal for both n- and p-type doping were examined.44,49 A pronounced angular dependence of the emitted THz radiation on the crystallographic orientation of the samples as well as on the optical pump beam polarization was observed. The experimental results are in good agreement with the theory, which predicts that for high excitation fluence, THz emission from narrow band gap semiconductors results primarily from surface electric field-induced optical rectification with small bulk contribution.50 This observation is in contrast with the earlier results obtained for wide bandgap semiconductors such as GaAs, in which the THz emission is primarily dominated by strong bulk contribution. The anomaly can be explained in the light of the theoretical calculations by Ching and Huang51 whereby narrow bandgap III–V semiconductors (InAs and InSb) are predicted to have third-order nonlinear susceptibilities (c3) several orders of magnitude higher than those of larger bandgap semiconductors. Among the zincblende crystals, perhaps the most popular candidate for generation of THz radiation by optical rectification is ZnTe. Nahata et al.11 first reported THz generation in ZnTe in an experiment that used a pair of ZnTe crystals for both generation and detection of THz radiation. In their work, a <110> ZnTe crystal was pumped by 130 femtosecond pulses at 800 nm from a mode-locked Ti:sapphire laser. The Fourier spectrum of the temporal waveform demonstrated a broad bandwidth with useful spectral information beyond 3 THz. Subsequently, Han et al.12 reported a higher frequency response of 17 THz limited only by a strong phonon absorption at 5.3 THz. Systematic studies have also been conducted on THz emitter application of cadmium zinc telluride ternary crystals with varying Cd composition. It has been reported18,52 that the optimum Cd composition x = 0.05 enhances THz radiation as well as crystal quality of ZnTe. Apart from the zincblende crystals described earlier, GaSe is a promising semiconductor crystal that has been exploited recently for THz generation with an extremely large bandwidth of up to 41 THz.15,53 GaSe is a negative uniaxial layered semiconductor with a hexagonal structure characteristic of 62m point group and a direct bandgap of 2.2 eV at 300 K. The crystal has a large nonlinear optical coefficient (54 pm/V),53 high damage threshold, suitable transparent range, and low absorption coefficient, which make it an attractive option for generation of
7525_C002.indd 51
11/15/07 10:47:07 AM
52
Terahertz Spectroscopy: Principles and Applications
broadband mid infrared electromagnetic waves. For broadband THz generation and detection using a sub-20 fs laser source, GaSe emitter-detector system performance is comparable to or better than the use of thin ZnTe crystals. Using GaSe crystals of appropriate thickness as emitter and detector it is also possible to obtain a frequencyselective THz wave generation and detection system. The disadvantage of GaSe lies in the softness of the material that makes it fragile during operation. 2.3.1.2 Inorganic Electrooptic Crystals In 1971 Yang et al. first demonstrated the generation of THz radiation by optical rectification of picosecond optical pulses in inorganic electrooptic materials. In their experiment they observed THz radiation from a LiNbO3 crystal illuminated by picosecond optical pulses from a mode-locked Nd:glass laser.8 In the late 1980s, Auston and coworkers reported THz radiation generation by optical rectification in LiTaO3 with spectral bandwidth as high as 5 THz.54 A major drawback in this experiment was the difficulty in extracting the THz pulses from the generating crystal because of total internal reflection owing to small critical angle (and high static dielectric constant) in LiTaO3. In their later publications Auston et al. reported an approach that minimized the reflection loss and permitted the extraction of the THz radiation into free space.10 Zhang et al.9 later measured and calculated optical rectification from LiNbO3 and y-cut LiTaO3 under normal incident optical excitation. The spatiotemporal shape of the radiated THz pulse was found to be similar for both materials with LiNbO3 emitting a stronger signal because of a smaller dielectric constant and hence smaller reflection losses at the crystal boundary. The maximum signal obtained from LiTaO3 was found to be 185 times smaller than that emitted by a 4-Nmethylstilbazolium tosylate (DAST) organic crystal.19 2.3.1.3 Organic Electrooptic Crystals Organic crystals have been a recent source of interest as THz emitters as they have been reported to generate stronger THz signals than commonly used semiconductors or inorganic electrooptic emitters owing to their large second-order nonlinear electric susceptibility. Zhang et al.19 first reported THz optical rectification from an organic crystal, dimethyl amino DAST, which is a member of the stilbazolium salt family. Electrooptic measurements at 820 nm have reported a high electrooptic coefficient (>400 pm/V).19 In their work on THz emission by optical rectification of femtosecond laser pulses in DAST, Zhang et al. observed a strong dependence of the radiated THz field amplitude on sample rotation about the surface normal, for both parallel and perpendicular orientations of the incident optical pump beam. The angular dependence was in excellent agreement with the predicted theory, with the maximum signal occurring for the angle at which the optical polarization, the crystal polar “a” axis and the detector dipole axis, were aligned in the same direction.19 Zhang and coworkers19 also reported that with a 180-mW optical pump beam focused to a 200-µm diameter spot, the best DAST sample provided a detected THz electric field that was 185 times larger than that obtained from an LiTaO3 crystal and 42 times larger than GaAs and InP crystals under the same experimental conditions. DAST has also been shown to
7525_C002.indd 52
11/15/07 10:47:09 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 53
perform well at higher frequencies with an observable bandwidth up to 20 THz from a 100-µm DAST crystal showing a six-fold increase over that reported from a 30-µm ZnTe crystal under similar experimental conditions.55 The frequency spectrum of DAST shows a characteristic strong absorption line at 1.1 THz (from TO phonon resonance) along with some additional absorption lines between 3 and 5 THz. The latter (with the exception of the line at 5 THz) are significantly weaker than the absorption line at 1.1 THz, such that the THz amplitude at these frequencies is still well above the noise level.56 Nahata et al.57 advocated the use of organic compounds in polymeric forms for THz-frequency radiation generation instead of single crystals as these compounds offer significant advantages over single crystals. In particular they are easily processable, can be poled to introduce noncentrosymmetry and have higher nonlinear coefficients than inorganic materials. In their experiment Nahata and coworkers used a copolymer of 4-N-ethyl-N- (2-methacryloxyethyl) amine-4′-nitro-azobenzene (MA1) and methyl methacrylate (MMA) (commonly known as MA1:MMA) for generation of THz radiation via optical rectification. The radiated field amplitude from a 16-mm thick sample (electrooptic coefficient ~11 pm/V) was found to be four times smaller than that observed from a 1-mm thick y-cut LiNbO3 crystal. However, the coherence length of the polymer was reported to be 20 times larger. Nahata and coworkers suggested that the conversion efficacy relative to LiNbO3 could be substantially improved using available polymers with six times the nonlinear coefficient and millimeter-thick films poled at high fields. This could be easily created by a dielectric stack of thin-poled films.58 After the success of DAST and MA1:MMA as THz emitters, Hashimoto et al. reported THz emission via optical rectification from organic single crystals of N-substituted (N-benzyl, N-diphenylmethyl, and N-2 naphthylmethyl) derivatives of 2-methyl-4-nitroaniline.59 While no substantial emission was observed from N-diphenylmethyl and N-2 naphthylmethyl derivatives (owing to the strong phonon modes existing in the range 0 to 2.5 THz), the integrated intensity of the THz radiation emitted by N-benzyl-2-methyl-4-nitroaniline (BNA) was as intense as that by the DAST crystal under similar experimental conditions. The dynamic range for BNA is limited to 2.1 THz because of a strong phonon mode that exists around 2.3 THz. Kuroyanagi and coworkers60 later reported improved signal intensity (about three times greater than that generated by ZnTe) and increased bandwidth (up to 4 THz) from highly purified BNA crystals. Although DAST and BNA have been reported to perform better than ZnTe when used for THz generation by optical rectification, the THz electric fields generated by these crystals are more complicated in both time and frequency domains. Phonon bands in these crystals also result in the production of smaller range of frequencies than ZnTe. Recent investigations of a range of organic molecular crystals revealed that the crystal (–) 2-(a-methylbenzyl-amino)-5-nitropyridine (MBANP) is superior to ZnTe when used for optical rectification at 800 nm.61 MBANP crystallizes in P21 monoclinic62 and has the advantage of being relatively easy to grow in single crystals, probably because of its L-shaped structure and strong H bonding in certain directions as well as a suitable habit.61 Optical rectification of 800-nm pulses in <001>-oriented MBANP resulted in THz pulses that are very similar to those
7525_C002.indd 53
11/15/07 10:47:10 AM
54
Terahertz Spectroscopy: Principles and Applications
produced by ZnTe both in frequency and time domain. However, MBANP produces a signal that is an order of magnitude higher because of its larger electrooptic coefficient (18.2 pm/V at 632.8 nm).63 Several other crystals similar to MBANP have also been studied.61 It was found that 4-(N, N-dimethylamino)-3-acetamidonitrobenzene and 4‑nitro-4′-methylbenzylidene aniline (NMBA) produced THz pulses through optical rectification of 800-nm pulses of comparable strength to MBANP. While NMBA is easy to grow, 4-(N, N-dimethylamino)-3-acetamidonitrobenzene is much more difficult owing to its needle-like habit, and obtainable crystal size is limited. Strong phonon band absorption also limits the power in the range 1.6 to 3 THz, which makes these crystals unsuitable for high-frequency applications. We have thus reviewed THz optical rectification from a variety of materials including semiconductors and inorganic and organic electrooptic crystals. The performance of these emitters in terms of bandwidth has been summarized in Table 2.3. ZnTe is the most popular choice for THz generation by optical rectification because it can generate extremely short and high-quality THz pulses. Organic crystals have been of recent interest owing to their higher electrooptic coefficient and enhanced capacity to generate stronger signals than the commonly used ZnTe. However, the THz fields generated by organic crystals such as DAST and more recently BNA are more complicated in both time and frequency domain. Low-frequency phonon bands also limit the bandwidth in these crystals than compared with ZnTe. Organic crystals also have a large naturally occurring birefringence, which complicates their application.55 This has resulted in ZnTe remaining the THz generator of choice. The comparative performance of a ZnTe THz emitter pumped by an amplified titanium sapphire laser system is shown in Figure 2.2.64 The choice of a suitable THz emitter also largely depends on the operating conditions. As mentioned previously, to achieve reasonable efficacy for nonlinear optical processes, long interaction length and appropriate phase matching conditions must be met. The phase matching condition is satisfied when the phase of the THz wave travels at the group velocity of the optical pulse. In the case of ZnTe, the phase matching condition and the subsequent enhancement of coherence length are achieved at 800 nm, making it the most suitable electrooptic crystal for THz wave emission and detection using a Ti:sapphire laser system with a center wavelength of 800 nm.
Table 2.3 Bandwidth Performances of Some Common Terahertz Emitters
Material GaAs GaSe ZnTe GaP DAST BNA
7525_C002.indd 54
Experimental Bandwidth (THz) 40(12) 41(15) 17(12) 3.5(45) 20(55) 2.1(59)
Lowest Optical Phonon Resonance (THz) at 300 K 8.02(71) 7.1(15) 5.4(12) 10.96(71) 1.1(56) 2.3(59)
Incident Pulse Wavelength (nm)
Incident Pulse Width (fs)
Detection Scheme
800(12) 780(15) 800(12) 1055(45) 800(55) 800(59)
12(12) 10(15) 12(12) 300(45) 15(55) 100(59)
Electrooptic Electrooptic Electrooptic PC antenna Electrooptic Electrooptic
11/15/07 10:47:11 AM
1000
Estimated based on measured saturation properties of ZnTe GaAs 10.7 kV/cm (You at al.) Fit based on (Darrow et al.)
(a)
G
0.1 1000
d
m a2 n
ae
sm
Pla
P
m
Ha
a(
m las
r ste
et
al.)
ETHz ∝ Jopt
Estimated based on measured saturation properties of ZnTe Fit based on (Darrow et al.) /cm 1kV s A Ga Te al.) Zn et m eld er t fi m s . 2 m xt Ha ae a( sm a m l s P Pla
10 1
on
ic
0.1
nd
ha
rm
0.01
JTHz ∝ Jopt2
as
m
a2
1E–3
Pl
1E–4 10–2 Pulse Energy Conversion (η)
eld
Fi xt.
GaAs 10.7 kV/cm (You et al.)
(b)
100
10
Te
Zn
as
m 2m
Pl
1
/cm
kV
ha
1 aAs
on ic
10
rm
100
GaAs 10.7 kV/cm (You et al.)
(c)
Estimated based on measured saturation properties of ZnTe
–3
Fit based on (Darrow et al.)
10–4 10–5
η∝
GaAs 1 kV/cm
10–6
m
10–7
2m
–8
1×10
1×10–9 1
10
J opt η∝
e ZnT Pla Ha sma 2 n rm d on ic
THz Pulse Energy (nJ)
Maximum Focused Field Amplitude (kV/cm)
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 55
100
d
. Fiel
a ext
Plasm
ma
Plas
ter ams
(H
1000
l.)
et a
J opt
η ∝ J op
t
10000
100000
Optical Pulse Energy (µJ)
Figure 2.2 Comparison of the THz emission efficacy of a 2-mm ZnTe crystal with other types of THz emitters: (a) the focused peak electric field, (b) the THz pulse energy, and (c) the energy conversion efficacy are displayed as a function of the energy per pulse of the femtosecond near infrared pump laser. (From Loeffler T., Semicond. Sci. Technol. 20, S140, 2005, IOP Publishing. With permission.)
7525_C002.indd 55
11/15/07 10:47:14 AM
56
Terahertz Spectroscopy: Principles and Applications
However, the large size of these lasers prevents them from being used in portable THz systems. To build a compact, integrated, and sensitive THz spectroscopy or THz imaging system, it has thus become crucial to develop a THz wave generation and detection technique coupled to an optical fiber cable. The erbium (Er)- and ytterbium (Yb)-doped fiber lasers operating at 1,550 nm and 1,000 nm, respectively, are especially attractive from this viewpoint. The large velocity mismatch and consequently a small coherent length, however, make ZnTe unsuitable for application at these wavelengths. Although GaP and CdTe have been suggested as potentially compatibles emitters for Yb-doped laser systems operating at 1,000 nm, GaAs is an excellent candidate for THz wave emission with erbium-doped fiber lasers. Calculations17 show that the phase matching condition is satisfied at 1,050 nm and 1 THz in CdTe crystals resulting in an enhancement of coherence length, whereas GaAs crystal phase matching occurs at 1,330 nm. This optical wavelength in GaAs is the longest among all binary semiconductors.14 Even at 1,550 nm, the coherence length still retains a large value, thus enabling GaAs to be used a suitable emitter in this wavelength range. GaAs also has the added advantage of having its lowest phonon resonance lying at higher THz frequencies (10 THz) and consequently increased bandwidth capability. The coherence length of some organic crystals such as BNA is also quite large in the long wavelength regime; however, because of the difficulties highlighted previously, organic crystals have not gained popularity as THz emitters.
2.3.2 Recent Developments The increasing interest in the development of novel THz sources has stimulated indepth studies of microscopic mechanisms of THz field generation in conventional semiconductors,38–53 electrooptic materials,55–63 and an extensive search for new materials to be employed in THz generation and detection. We conclude our discussion on THz emitters by highlighting some recent developments in THz emitter research. The THz emission from nonresonant optical rectification discussed in earlier sections resulted from dipolar excitations from such materials as GaAs, ZnTe, and LiNbO3. THz emission may also result from nondipolar excitations. Emission via optical rectification of femtosecond laser pulses in YBa2Cu3O7,65 single crystals of iron (Fe),66 and films consisting of nanosized graphite crystallites67 was observed and was found to have resulted from quadrupole magnetic dipole nonlinearities. For Fe, which crystallizes in a body-centered cubic lattice, optical rectification is forbidden by lattice symmetry. A nonvanishing second-order optical nonlinearity can, however, result from an electric quadrupole magnetic dipole contribution, surface nonlinearity or sample magnetization. Each of these contributions to the second-order nonlinear electric susceptibility has a characteristic dependence on sample azimuth and optical pump pulse polarization for a given crystal orientation. The THz emission reported from Fe was found to be approximately three orders of magnitude weaker than that from a 1-mm thick <110> ZnTe crystal under the same optical excitation conditions. THz emission from metals such as gold and silver has also come to light recently.20,21 Although second harmonic generation had been reported from metal surfaces as early as the 1960s, optical rectification of laser light had not been reported until recently. Kadlec et al.20,21 generated intense THz emission by optical
7525_C002.indd 56
11/15/07 10:47:15 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 57
rectification of p‑polarized 810-nm laser pulses at a fluence of 6 mJ/cm2 in gold films. The THz amplitude was found to scale quadratically with optical fluence for values up to 2 mJ/cm2. The s-polarized optical pump beam resulted in THz radiation emission, which was approximately three times weaker than the signal obtained from a p-polarized optical pump beam. THz emission from silver showed a different behavior. At the highest optical pump fluence, the emitted THz radiation was 15 times weaker than for gold and showed a linear dependence on incident pump fluence.20 These recent experimental findings reveal the possibility of accessing a wealth of new information about nonlinear optical properties and electronic structures of metal surfaces via femtosecond optically excited THz emission measurements.
2.4 Experimental Results of Terahertz Electrooptic Detection Much research activity has been devoted to increasing the sensitivity and bandwidth of electrooptic detection of THz-frequency radiation pulses. Other than the duration of the optical probe pulse, the bandwidth of free-space electrooptic sampling is only limited by the dielectric properties of the electrooptic crystal. Electrooptic sampling of THz-frequency radiation is a powerful tool for detection of electromagnetic radiation pulses in and beyond the mid-infrared range. A variety of electrooptic materials, including semiconductors and inorganic and organic electrooptic crystals, have been tested for detector applications in THz spectroscopy. In this section, we present a brief overview of the experimental results of broadband THz electrooptic detection with various materials.
2.4.1 Materials 2.4.1.1 Semiconductors and Inorganic Crystals In 1995, Wu and Zhang27 first demonstrated free-space electrooptic sampling of short THz radiation pulses. In their experiment, a GaAs photoconductive emitter triggered by 150-fs optical pulses at 820 nm radiated electromagnetic waves of THz frequency. A 500-µm thick LiTaO3 crystal, with its c axis parallel to the electric field polarization, was used as the electrooptic sampling element. To improve detection efficacy, the THz radiation beam was focused onto the detector crystal by a highresistivity silicon lens. The temporal resolution of the detected THz transient was limited by the velocity mismatch between optical and THz frequencies. Later work by Wu and Zhang68,69 addressed this shortcoming by careful geometric design of the radiation emitter and a special cut detector crystal. A signal-to-noise ratio of about 170:1 was obtained with a 0.3-second lock-in integration time constant. Wu and coworkers also tested ZnTe for detector applications in a novel experimental geometry in which the optical and THz beams were made to propagate collinearly in the electrooptic crystal.68 In this setup, a 1.5-mm thick, <110>-oriented ZnTe crystal was used as the detector with the optical probe and THz beam set parallel to the <110> edge of the ZnTe crystal for optimal electrooptic phase modulation. A signal-to-noise ratio of about 10,000:1 was obtained for a single scan using again a lock-in amplifier with time constant of 0.3 seconds. Nahata et al.11 demonstrated a
7525_C002.indd 57
11/15/07 10:47:16 AM
58
Terahertz Spectroscopy: Principles and Applications
broadband time domain THz spectroscopy system using <110>-oriented ZnTe crystals for generation of THz radiation by optical rectification and detection of THz radiation by electrooptic sampling. An important condition for generation and detection of THz radiation by nonlinear optical techniques is the appropriate phase matching between the optical and THz pulses in the nonlinear optical crystal. For a medium with dispersion at optical frequencies, phase matching is achieved when the phase velocity of THz wave is equal to the velocity of optical pulse envelope (or the optical group velocity).11 The data in Figure 2.8 show the effective index of refraction of ZnTe at optical wavelengths nopt eff and THz frequencies nTHz. The coherence length lc of ZnTe at THz frequencies for an optical wavelength λ = 780 nm decreases as illustrated in Figure 2.3. The temporal waveform of the measured THz electric field and its Fourier amplitude and Fourier phase are displayed in Figures 2.3, 2.4, and 2.5, respectively. The peak of the THz pulse amplitude shows a three-fold rotational symmetry when the ZnTe detector crystal is rotated by 360° about an axis normal to the <110> surface. This result is inherent to all <110> and <111> zincblende crystals.40 The broadband detection capability of ZnTe is obvious from the Fourier amplitude spectrum (Figure 2.4), which extends well beyond 2 THz. The rolloff in sensitivity for higher frequencies from phase mismatch and the shorter coherence length are in agreement with data presented in Figures 2.6, 2.7, and 2.9. A thinner crystal detects higher frequencies better than a thicker crystal. However, the detector sensitivity of a thinner crystal is reduced compared to a thicker crystal. In addition to limitations imposed by
Electro-optic Signal (arb. units)
4 2 0 –2 –4 2
4
6
8
10
Time (ps)
Figure 2.3 Time domain measurement of a THz pulse by electrooptic sampling with a ZnTe crystal 10 mm × 10mm × 1 mm in size. The THz pulse and the optical probe pulse are incident onto the surface of the ZnTe crystal parallel to the <110> plane. The optical axis of the crystal is in the <001> direction. The linear polarization of the THz radiation pulse is perpendicular to the optical axis. The linear polarization of the incident optical probe pulse is parallel to the optical axis. (Adapted from Selig, H., Elektro-optisches Sampling von Terahertz Pulsen, Hochschulschrift: Hamburg, Universitaet, Fachbereich Physik, Diplomarbeit, 7,2000. With permission.)
7525_C002.indd 58
11/15/07 10:47:18 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 59
Fourier-amplitude (arb. units)
104
103
102
101
100
0.5
1.0
1.5
2.0
2.5
3.0
Frequency f (THz)
Figure 2.4 Fourier amplitude of the time domain measurement displayed in Figure 2.3. The bandwidth of the signal is approximately 2.75 THz. The dynamic range of the measurement is 500:1. (Adapted from Selig, Hanns, Elektro-optisches Sampling von Terahertz Pulsen, Hochschulschrift: Hamburg, Universitaet, Fachbereich Physik, Diplomarbeit, 7, 2000. With permission.)
phase mismatch, the absorption caused by a transverse optical phonon resonance at 5.4 THz11 in ZnTe is expected to attenuate the high-frequency components of THz radiation. Later experiments by Han and Zhang70 reported a detection bandwidth up to 40 THz using a 27-µm ZnTe detector crystal. 2.0×104
Fourier-phase (arb. units)
1.9×104 1.8×104 1.7×104 1.6×104 1.5×104 1.4×104 1.3×104 0.0
0.5
1.0
1.5
2.0
2.5
3.0
Frequency f (THz)
Figure 2.5 Fourier phase of the time domain measurement displayed in Figure 2.3. (Adapted from Selig, H., Elektro-optisches Sampling von Terahertz Pulsen, Hochschulschrift: Hamburg, Universitaet, Fachbereich Physik, Diplomarbeit, 7, 2000. With permission.)
7525_C002.indd 59
11/15/07 10:47:20 AM
60
Terahertz Spectroscopy: Principles and Applications
Electro-optic Signal (arb. units)
6 4 2 0 –2 ZnTe 0.5 mm ZnTe 1.0 mm
–4 –6
0
1
2
3
4
5
6
7
8
Time (ps)
Figure 2.6 Time domain measurements of THz pulses by electrooptic sampling with ZnTe crystals of different thickness. For both measurements, the optical probe beam and the THz pulse both incident onto the surface of the crystals parallel to the <110> plane. The surface of the crystals is 10 mm × 10 mm. The linear polarizations of the incident THz-pulse and probe pulse are perpendicular to each other. The polarization of the probe beam is parallel to the optical axis (<001> direction). The ratio of the peak-to-peak amplitude of the THz pulses measured by the 1-mm crystal and the 0.5-mm crystal is 2.3 and scales approximately with the thickness of the two crystals (1 mm/0.5 mm = 2). The thicker ZnTe crystal exhibits a larger signal than the thinner crystal because the phase retardation G ∝ l is linearly proportional to the thickness l of the electrooptic crystal. (Adapted from Selig, H., Elektro-optisches Sampling von Terahertz Pulsen, Hochschulschrift: Hamburg, Universitaet, Fachbereich Physik, Diplomarbeit, 35,2000. With permission.)
Although ZnTe delivers excellent performance in the 800-nm wavelength regime, its efficacy is inherently limited by large group velocity mismatch (GVM) of 1 ps/mm68 between optical and THz frequencies. An ideal material would be one with larger electrooptic coefficient and lower GVM. At 886 nm, GaAs has been found to possess a moderate electrooptic coefficient (25 pm/V), but a low GVM of 15 fs/mm. The electrooptic coefficient of LiTaO3 was found to be comparable to that of ZnTe, but LiTaO3 has a large GVM (>14 ps/mm), whereas for organic crystals such as DAST, the electrooptic coefficient is very large but GVM is comparable to ZnTe.68 A substantial improvement in bandwidth detection and sensitivity may be obtained by using materials with phonon resonance occurring at higher THz frequencies. Among inorganic media with comparable nonlinear optical properties zinc selenide (lowest TO phonon resonance at 6 THz),11 GaAs (TO phonon resonance at 8 THz), and GaP (TO phonon resonance at 11 THz)71 are excellent candidates. To verify the performance of electrooptic sampling with GaAs, Vosseburger et al.72 performed time-resolved experiments of THz radiation detection using bulk GaAs as the electrooptic sampling element. An excitation wavelength of 900 nm was chosen to avoid photoexcitation of carriers by interband absorption in the GaAs. The measured THz radiation pulse had a complex
7525_C002.indd 60
11/15/07 10:47:22 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 61 104
Fourier Amplitude (arb. units)
ZnTe 0.5 mm ZnTe 1.0 mm 103
102
101
100 0.0
0.5
1.0
1.5
2.0
2.5
3.0
Frequency (THz)
Figure 2.7 Fourier amplitudes of the time domain measurements displayed in Figure 2.6. The thinner ZnTe crystal has a slightly larger bandwidth than the thicker ZnTe crystal. The calculated bandwidths of a 0.5-mm and a 1.0-mm ZnTe crystal are 2.86 THz and 2.62 THz, respectively. (Adapted from Selig, H., Elektro-optisches Sampling von Terahertz Pulsen, Hochschulschrift: Hamburg, Universitaet, Fachbereich Physik, Diplomarbeit, 35,2000. With permission.)
Optical Wavelength (Nm) 6.0
0.5
0.6
0.7
0.8
0.9
1.0 6.0
Index of Refraction n
5.5
5.5 nTHz
nopt eff
5.0
5.0
4.5
4.5
4.0
4.0
3.5
3.5
3.0
3.0
2.5
2.5
2.0
0
1
2
3
4
5
2.0
Frequency f (THz)
Figure 2.8 Index of refraction of ZnTe at optical wavelength (nopt eff ) and THz frequencies (nTHz). Optical radiation at 760-µm wavelength propagates at the same speed as 2.6 THz- frequency radiation in ZnTe. The effective index of refraction at λ = 780 µm is nopt eff = 3.27. (Adapted from Selig, H., Elektro-optisches Sampling von Terahertz Pulsen, Hochschulschrift: Hamburg, Universitaet, Fachbereich Physik, Diplomarbeit, 33, 2000. With permission.)
7525_C002.indd 61
11/15/07 10:47:25 AM
62
Terahertz Spectroscopy: Principles and Applications
Coherence Length lc (mm)
10
1
0.1
0.01
0
1
2
3
4
5
Frequency (THz)
Figure 2.9 Calculated coherence length lc of ZnTe as a function of THz frequency for λ = 780 µm. (Adapted from Selig, H., Elektro-optisches Sampling von Terahertz Pulsen, Hochschulschrift: Hamburg, Universitaet, Fachbereich Physik, Diplomarbeit, 7, 2000. With permission.)
temporal structure and was smaller by a factor of approximately 20 compared with the same pulse measured by a ZnTe crystal. The reduction in amplitude had its origins in the smaller electrooptic coefficient of GaAs than that of ZnTe and poor phase matching of GaAs at 900 mm and 1 THz. Among zincblende crystals, GaP is an excellent alternative to ZnTe for electrooptic sampling of THz-frequency radiation because of its high-frequency phonon band at 11 THz,71 the highest available among all zincblende crystals. The electrooptic coefficient of GaP (r41 ≈ 0.97 pm/V30), however, is one fourth that of ZnTe. In 1997, Wu and Zhang73 first demonstrated electrooptic sampling of THz radiation with a GaP crystal. Using a GaAs emitter excited by 50-fs pulses and a 150-µm thick <110> GaP crystal, they demonstrated a bandwidth resolution up to 7 THz. Broadband THz electrooptic sampling with GaP crystals was further developed by Leitenstorfer et al.74 They carefully evaluated the frequency dependence of the refractive index, the electrooptic coefficient and the response function of the GaP electrooptic THz detector. Using a 13-µm thick crystal and 12-fs titanium–sapphire laser pulses the detected spectral bandwidth of GaP was estimated to be ~70 THz. One of the recently reported materials used for free-space electrooptic sampling of THz radiation is ZnSe in crystalline and polycrystalline form.75 Although the electrooptic coefficient of ZnSe (r41 ≈ 2pm/V75) is only half of that of ZnTe, the TO phonon resonance frequency (6 THz)11 is higher than that of ZnTe (5.4 THz),11 thus promising a higher detection bandwidth potential for the former. The GVM for ZnSe (0.96 pm/V75) is comparable to that for ZnTe. Using a 10-fs titanium–sapphire laser pulse to excite a 100-µm GaAs photoconducting antenna and a 0.5-mm, <111>-oriented ZnSe single crystal as detector, a spectral bandwidth of 3 THz was
7525_C002.indd 62
11/15/07 10:47:28 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 63 90 120
1.0
φ (°)
60
Electro-optic Signal (arb. units)
0.8 30
150
0.6 0.4 0.2 0.0
180
0
0.2 0.4 0.6
330
210
0.8 1.0
240
300 270
Figure 2.10 Measurements of the peak electrooptic signal as a function of the angle Φ between the <001> direction of a <110> ZnTe crystal and the direction of linear polarization of the optical probe beam. The polarization of the THz pulse is perpendicular to the polarization of the optical probe pulse. During the measurements, the orientations of the polarization of the optical and the THz pulses are fixed and the crystal is turned in steps of 10°. An angle Θ = 90° corresponds to the situation in which the polarization of the optical probe beam is parallel to the <001> direction of the ZnTe. Two major maxima at Θ = 90° and Θ = 270° and four minor maxima at Θ = 30°, Θ = 150°, Θ = 210°, and Θ = 330° are observed. The amplitude of the peak THz electric field is estimated to be 5 V/m. (Adapted from Selig, H., Elektro-optisches Sampling von Terahertz Pulsen, Hochschulschrift: Hamburg, Universitaet, Fachbereich Physik, Diplomarbeit, 47, 2000. With permission.)
measured. In this experiment, the bandwidth detected by the ZnSe crystal was limited only by the generation of the THz radiation. It was found that for thicker (1 mm) polycrystalline electrooptic ZnSe samples, the random nature of crystallographic orientations within the interaction length distorted the phase of THz waveform. However, a reduction of the thickness to 0.15 mm minimized the distortion and extended the bandwidth up to 4 THz. Because polycrystalline semiconductors offer practical advantages in terms of ease of fabrication75 over their single crystal counterparts, the successful application of polycrystalline materials for free-space electrooptic sampling permits the possibility of utilizing non-lattice matched thin film integrated electrooptic detectors of THz radiation. As discussed previously, the mismatch between THz phase velocity and the group velocity of the optical probe pulse limits the detection bandwidth of zincblende electrooptic crystals such as ZnTe and GaP. However, this limitation can be eliminated by using a novel detection scheme, taking advantage of the type II phase matching in a naturally birefringent crystal such as GaSe.53,76 The phase matching condition can be satisfied by angle tuning whereby the electrooptic crystal
7525_C002.indd 63
11/15/07 10:47:33 AM
64
Terahertz Spectroscopy: Principles and Applications
Table 2.4 Properties of Typical Electrooptic Sensor Materials*
Material
Crystal Structure
Point Group
ZnTe GaP ZnSe LiTaO3
Zincblende(30) Zincblende(30) Zincblende(30) Trigonal(30)
43m( 30 ) 43m( 30 ) 43m( 30 ) 3m(30)
GaSe DAST Poled polymers
Hexagonal(53) — —
62 m( 53) — —
Electrooptic Coefficient (pm/V)
Group Velocity Mismatch (ps/mm)
Surface Orientation
1.1(68) — 0.96(75) 14.1(68)
110(11) 110(73) 111(75) —
2.5(11) 7(73) 3(75) —
0.10(76) 1.22(68) —
— — —
120(76) 6.7(77) 33(78)
r41 = 3.90(30) r41 = 0.97(30) r41 = 2.00(30) r33 = 30.3(30) r13 = 5.70 r22 = 14.4(76) r11 = 160(68) —
Experimental Detection Bandwidth (THz)†
* A more comprehensive listing may be found in reference 68. † The bandwidth reported here is subject to experimental conditions and not the absolute bandwidth for a particular emitter/sensor material.
(z-cut GaSe crystal) is tilted by an angle qdet (the phase matching angle) about a horizontal axis perpendicular to the direction of time-delayed probe beam.76 In the experiments conducted by Kubler and coworkers,76 a THz radiation pulse was generated by optical rectification of 10-fs titanium–sapphire laser pulses in a 20-µm thick GaSe crystal (qem = 57°) and detected with a GaSe sensor (qdet = 60°) of thickness 30 µm. qdet/em = 0 signifies normal incidence. The amplitude spectrum of the THz pulse peaked at 33.8 THz and extended from 7 THz to beyond 120 THz. Compared with a 12-µm thick ZnTe crystal that displayed a local minimum at 34 THz under the same excitation, the GaSe spectrum showed a nearly flat response from 10 THz up to 105 THz. The enhanced performance of GaSe crystals over ZnTe crystals is attributed mainly to a greater interaction length because of better phase matching and a larger electrooptic coefficient of GaSe (Table 2.4). 2.4.1.2 Organic Crystals In the quest for novel materials for electrooptic sampling of THz radiation pulses, organic electrooptic crystals have attracted attention owing to their very high electrooptic coefficients. Han and coworkers55 first demonstrated the application of the organic ionic salt crystal DAST as a free space electrooptic detector of THz radiation. The electrooptic coefficient for DAST is 160 pm/V at 820 nm68 and is almost two orders higher than that found in ZnTe (Table 2.4). However, DAST exhibits two confirmed phonon absorption peaks at 1.1 THz and 3.05 THz.77 Recently, nonlinear optical generation and detection of THz radiation pulses was investigated theoretically and experimentally by Schneider et al.77 They demonstrated that the THz radiation spectrum generated and detected using DAST crystals extended from 0.4 THz to 6.7 THz, depending on the laser excitation wavelength in the 700-nm
7525_C002.indd 64
11/15/07 10:47:35 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 65
to 1,600-nm wavelength range. Furthermore, they found that the technologically important wavelengths around 1,500 nm are velocity matched to THz frequencies between 1.5 THz and 2.7 THz. Among other organic materials, poled polymers have been reported to exhibit excellent broadband electrooptic detection capability.78 These materials demonstrate large electrooptic coefficients,79 low dispersion between the THz and optical refractive indices,57,80 ease of fabrication in large area thin films, and easily modifiable chemical structures for better THz and optical properties because of their organic nature. Using poled polymers for free-space electrooptic detection, Nahata and coworkers78 recently measured an amplitude spectrum up to frequencies of 33 Hz.
2.5 Application of Electrooptic Sampling of THz Electric Field Transients Nonlinear techniques for the generation and detection of short pulses of THz- frequency radiation have found important applications such as time domain THz spectroscopy and time domain THz imaging.34 Here, we discuss briefly the application of electrooptic sampling of THz radiation pulses to longitudinal electron bunch length measurements. The electrooptic detection of the local nonradiative electric field that travels with a relativistic electron bunch has recently emerged as a powerful new technique for subpicosecond electron bunch length measurements.81–84 The method makes use of the fact that the local electric field of a highly relativistic electron bunch that moves in a straight line is almost entirely concentrated perpendicular to its direction of motion. Consequently, the Pockels’ effect induced by the electric field of the passing electron bunch can be used to produce birefringence in an electrooptic crystal placed in the vicinity of the beam. Specifically, the birefringence induced by a single electron bunch is measured by monitoring the change of polarization of the wavelength components of a chirped, synchronized titanium–sapphire laser pulse. When the electric field of an electron bunch and the chirped optical pulse copropagate in the electrooptic crystal, the polarizations of the various wavelength components of the chirped pulse that passes through the crystal are rotated by different amounts that correspond to different portions of the local electric field. The direction and degree of rotation are proportional to the amplitude and the phase of the electric field. Thus the time profile of the local electric field of the electron bunch is linearly encoded to the wavelength spectrum of the optical probe beam. An analyzer converts the modulation of the polarization of the chirped optical pulse into an amplitude modulation of its spectrum. The time profile of the electric field of the electron bunch is measured as the difference of the spectrum with and without a copropagating electron bunch. The width of the temporal profile corresponds directly to the electron bunch length, and the shape of the temporal profile is proportional to the longitudinal electron distribution within the electron bunch. The length and the shape of individual electron bunches are determined by measuring the spectra of single chirped laser pulses with an optical multichannel analyzer equipped with a nanosecond shutter. The method allows direct in situ electron bunch diagnostics with a high signal‑to‑noise ratio and subpicosecond time resolution.
7525_C002.indd 65
11/15/07 10:47:36 AM
66
Terahertz Spectroscopy: Principles and Applications
Grating f + ∆z
Lens
Mirror
f
Pulse Generator ccd Intensifier Spectrometer
Signal
(a) Optical Stretcher
Reference Ti: Sapphire Amplifier
Optical Stretcher (a)
Fiber Analyzer
Polarizer FEL Cavity
FEL
rf-clock ZnTe Accelerator
e-beam
Undulator Dump
Figure 2.11 Experimental setup for electron bunch length measurements by electrooptic sampling with chirped optical pulses. The electron bunch length is measured by using a ZnTe crystal placed inside the vacuum pipe at the entrance of the undulator. The femtosecond near infrared laser repetition rate is synchronized with the repetition rate of the electron bunches. The inset (a) exhibits a two-dimensional optical stretcher for laser pulse chirping. (Adapted figure with permission from I. Wilke, A. M. McLeod, W. A. Gillespie, G. Berden, G. M. H. Knippels, A. F. G. van der Meer, Phys. Rev. Lett. 88, 124801-1 (2002). Copyright 2002 by the American Physical Society.)
The experimental arrangements for the electrooptic electron bunch length measurements are schematically illustrated in Figure 2.11. The electron bunch source is the radiofrequency linear accelerator at the FELIX free electron laser facility in the Netherlands.85 The electron beam energy of FELIX was set at 46 MeV, and its charge per bunch at around 200 pC. The micropulse repetition rate was 25 MHz, and the macropulse duration was around 8 µ with a repetition rate of 5 Hz. A titanium– sapphire amplifier, producing 30-fs FWHM pulses at 800 nm with a repetition rate of 1 kHz, was used as a probe beam. The 30-fs optical laser pulses are chirped to pulses of up to 20 ps (FWHM) duration with an optical stretcher which consists of a grating, a lens, and a plane mirror.86 The duration of the chirped pulses has been measured with an optical autocorrelator based on second harmonic generation in a BBO crystal. The electron bunch length is measured inside the accelerator beam pipe at the entrance of the undulator. A 0.5-mm thick <110> ZnTe crystal is used as an
7525_C002.indd 66
11/15/07 10:47:39 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 67
electrooptic sensor and is placed with its 4 × 4 mm 2 front face perpendicular to the propagation direction of the electron beam. The incoming chirped laser beam is linearly polarized. The outgoing chirped beam is split into a signal beam and a reference beam used to monitor possible laser power fluctuations. The signal beam passes through an analyzer (a second polarizer), which is crossed with respect to the first polarizer. Subsequently, the spectra of the chirped laser pulses are dispersed with a grating spectrometer and the line spectra are focused onto a charge-coupled device (CCD) camera. The CCD camera is equipped with an intensifier, which acts as a nanosecond shutter with a gate width of 100 ns. Single-shot measurements are performed by actively synchronizing the titanium–sapphire amplifier87 with both the repetition rate of the electron beam and the gate of the CCD camera, and therefore recording only the spectrum of one chirped laser pulse at a time. The temporal overlap between the electron bunch and chirped laser pulse is controlled by an electronic delay. Figure 2.12a shows measurements of the chirped laser pulse spectra with and without a copropagating electron bunch. The signal spectra are labeled by S and S′. The crossed polarizers exhibit a finite transmission of 1.7% if the electron bunch does not overlap with the chirped laser pulse. This is attributed to a small intrinsic stress birefringence of the ZnTe. The transmission of the crossed polarizers changes significantly when the electron bunch and the laser pulse copropagate: in these circumstances, a large peak, which corresponds to a strong enhancement of the transmission, is observed in the center of the spectrum. The strong change of the spectrum is attributed to the wave length-dependent change in polarization of the chirped laser pulse because of the electric field of the electron bunch. The length and shape of the electron bunch is obtained by subtracting the spectrum without copropagating electron bunch, which has been corrected for laser power fluctuations by multiplication with the ratio of the reference spectra R/R′ from the spectrum with copropagating electron bunch. This difference S-(S′R/R′) is corrected for the wavelength-dependent variations in intensity in the spectrum by dividing by the spectrum S′R/R′. The pixels are converted to time by measuring the length of the chirp t, the spectral resolution of the spectrometer and CCD setup, Dl/pixel, and the bandwidth of the chirped laser pulses Dlbw. Then, the time interval per pixel is given by (Dt/pixel) = (Dl/pixel)/(t/Dlbw). For the spectra of Figure 2.12a, the chirp was 4.48 ps FWHM, which results in an electron bunch measurement as displayed in Figure 2.12b. The width of the electron bunch is (1.72 ± 0.05) ps FWHM. The signal-to-noise ratio depends on the position in the spectrum; in the center of the spectrum, it is better than 200:1. The measured width and shape of a single electron bunch agree very well with the electron bunch measurements averaged over more than 8,000 electron bunches88 and CTR measurements.89 Linear accelerators used as drivers for new femtosecond x‑ray free‑electron lasers or employed in new teraelectron volt linear electronpositron colliders for high-energy physics, require dense, relativistic electron bunches with bunch lengths shorter than a picosecond. Precise measurements of the electron bunch length and its longitudinal charge distribution are important to monitor the preservation of the beam quality, whereas the electron bunch train travels through the beam pipe, as well as to tune and to operate a linear collider or a FEL.
7525_C002.indd 67
11/15/07 10:47:40 AM
68
Terahertz Spectroscopy: Principles and Applications 5×104 4×104
S S´
Counts
3×104 2×104 1×104 0 100
200
300
400
Pixel (a)
Norm. Electro-optic Signal (a.u.)
1.0 0.8 0.6 0.4 0.2 0.0 –0.2
–4
–2
0
2
4
Time (ps) (b)
Figure 2.12 Fig. 2.12 (a) Measurements of the chirped laser pulse spectra with(s) and without (s′) a copropagating electron bunch. (b) single shot electron bunch length measurements. The width of the electron bunch is (1.72 ± 0.05) ps FWHM.
References 1. Mittleman, D., Ed., Sensing with terahertz radiation, Springer Optical Science 85. Berlin: Springer, 2003. 2. Nuss, M. C., and Orenstein, J., Terahertz time-domain spectroscopy, in Millimeter and sub-millimeter-wave spectroscopy of solids, Grüner, G., ed., Topics in Applied Physics 74. Berlin: Springer, 1998.
7525_C002.indd 68
11/15/07 10:47:42 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 69 3. Brucherseifer, M., et al., Label free probing of binding state of DNA by time-domain terahertz sensing, Appl. Phys. Lett., 77, 4049, 2000. 4. Kaindl, R. L., et al., Ultrafast terahertz probes of transient conducting and insulating phases in an electron-hole gas, Nature, 423, 73, 2003. 5. Corson, J., et al., Vanishing of phase coherence in underdoped Bi2Sr2CaCu2O8+d Nature, 398, 221, 1999. 6. Karpowicz, N., et al., Compact continuous-wave terahertz system for inspection applications, Appl. Phys. Lett., 86, 54105, 2005. 7. Wallace, V. P. et al., Terahertz pulsed imaging and spectroscopy for biomedical and pharmaceutical applications, Faraday Discuss., 126, 255, 2004. 8. Yang, K. H., Richards, P. L., and Shen, Y. R., Generation of far-infrared radiation by picosecond light pulses in LiNbO3, Appl. Phys. Lett., 19, 320, 1971. 9. Zhang, X. C., Jin, Y., and Ma, X. F., Coherent measurement of terahertz optical rectification from electrooptic crystals, Appl. Phys. Lett., 61, 2764, 1992. 10. Hu, B. B., et al., Free-space radiation from electrooptic crystals, Appl. Phys. Lett., 56, 506, 1990. 11. Nahata, A., Weling, A. S., and Heinz, T. F., A wideband coherent terahertz spectroscopy system using optical rectification and electrooptic sampling, Appl. Phys. Lett., 69, 2321, 1996. 12. Han, P. Y., and Zhang, X. C., Free-space coherent broadband terahertz time-domain spectroscopy, Meas. Sci. Technol., 12, 2001, 1747. 13. Rice, A., et al., Terahertz optical rectification from <110> zinc-blende crystals, Appl. Phys. Lett., 64, 1324, 1994. 14. Nagai, M. et al., Generation and detection of terahertz radiation by electrooptical process in GaAs using 1.56 µm fiber laser pulses, Appl. Phys. Lett., 85, 3974, 2004. 15. Huber, R., et al., Generation and field resolved detection of femtosecond electromagnetic pulses tunable up to 41 THz, Appl. Phys. Lett., 76, 3191, 2000 16. Shi, W. et al., Efficient, tunable and coherent 0.18–5.27-THz source based on GaSe crystal, Opt. Lett., 27, 1454, 2002. 17. Xie, X., Xu, J., and Zhang, X.C., Terahertz wave generation and detection from a CdTe crystal characterized by different excitation wavelengths, Opt. Lett., 31, 978, 2006. 18. Liu, K. et al., Study of ZnCdTe crystals as THz wave emitters and detectors, Appl. Phys. Lett., 81, 4115, 2002. 19. Zhang, X.C. et al., Terahertz optical rectification from a nonlinear organic crystal, Appl. Phys. Lett., 61, 3080, 1992. 20. Kadlec, F., Kuzel, P., and Coutaz J.L., Optical rectification at metal surfaces, Opt. Lett., 29, 2674, 2004. 21. Kadlec, F., Kuzel, P., and Coutaz J.L., Study of terahertz radiation generated by optical rectification on thin gold films, Opt. Lett., 30, 1402, 2005. 22. Bass, M., et al., Optical rectification, Phys. Rev. Lett., 9, 446, 1962. 23. Zernike, F., Jr., and Berman, P. R., Generation of far infrared as a difference frequency, Phys. Rev. Lett., 15, 999, 1965. 24. Pockels, F., Lehrbuch der Kristalloptik, Bibliotheca Mathematica Teubneriana. Leipzig: Band 39, 1906. 25. Harris, S. E., McMurtry, B. J., and Siegman, A. E., Modulation and direct demodulation of coherent and incoherent light at microwave frequency, Appl. Phys. Lett., 1, 37, 1962. 26. Valdmanis, J. A., Mourou, G., and Gabel, C. W., Picosecond electrooptic sampling system, Appl. Phys. Lett., 41, 211, 1982. 27. Wu, Q., and Zhang, X. C., Free-space electrooptic sampling of terahertz beams, Appl. Phys. Lett., 67, 3523, 1995.
7525_C002.indd 69
11/15/07 10:47:44 AM
70
Terahertz Spectroscopy: Principles and Applications 28. Jepsen, P. U., et al., Detection of THz pulses by phase retardation in lithium tantalate, Phys. Rev. E, 53, 3052, 1996. 29. Nahata, A., et al., Coherent detection of freely propagating terahertz radiation by electrooptic sampling, Appl. Phys. Lett., 68, 150, 1996. 30. Yariv, A., Modulation of optical radiation, in quantum electronics, 3rd ed., Hoboken, NJ. John Wiley & Sons, 1988. 31. Armstrong, J. A., et al., Interactions between light waves in a non-linear dielectric, Phys. Rev., 127, 1918, 1962. 32. Bonvalet, A. and Joffre, M., Terahertz femtosecond pulses, in Femtosecond laser pulses: principles and experiments, Rullière, C., ed., Berlin: Springer, 1998. 33. Shen, J., Nahata, A., and Heinz, T. F., Terahertz time-domain spectroscopy based on nonlinear optics, J. Nonlinear Opt. Phys., 11, 31, 2002. 34. Jiang, Z., and Zhang X. C., Free space electrooptic techniques, in Sensing with terahertz radiation, Optical Science 85, Mittleman, D., ed., Berlin: Springer, 2003, 155. 35. Franken, P. A., and Ward, J. F., Optical harmonics and nonlinear phenomena, Rev. Mod. Phys., 35, 23, 1963. 36. Hirlimann, C., Further methods for the generation of ultrashort optical pulses, in Femtosecond laser pulses: principles and experiments, Rullière, C., ed., Berlin: Springer, 1998. 37. Planken, P. C. M., et al., Measurement and calculation of the orientation dependence of terahertz pulse detection in ZnTe, J. Opt. Soc. Am. B., 18, 313, 2001. 38. Zhang, X. C. et al., Generation of femtosecond electromagnetic pulses from semiconductor surfaces, Appl. Phys. Lett., 56, 1011, 1990. 39. Greene, B. I., et al., Interferometric characterization of 160 fs far-infrared light pulses, Appl. Phys. Lett., 59, 893, 1991. 40. Zhang, X. C., and Auston, D. H., Optoelectronic measurement of semiconductor surfaces and interfaces with femtosecond optics, J. Appl. Phys., 71, 326, 1992. 41. Jin, Y. H., and Zhang, X. C., Terahertz optical rectification, J. Nonlinear Opt. Phys., 4, 459, 1995. 42. Chuang, S. L. et al., Optical rectification at semiconductor surfaces, Phys. Rev. Lett., 68, 102, 1992. 43. Greene, B. I., et al., Far-infrared light generation at semiconductor surfaces and its spectroscopic applications, IEEE J. Quantum Electron, 28, 2302, 1992. 44. Reid, M., Cravetchi, I. V., and Fedosejevs, R., Terahertz radiation and second harmonic generation from InAs: bulk versus surface electric field induced contributions, Phys. Rev. B., 72, 035201-1, 2005. 45. Chang, G., et al., Power scalable compact THz system based on an ultrafast Ybdoped fiber amplifier, Opt. Express, 14, 7909, 2006. 46. Gu, P., et al., Study of THz radiation from InAs and InSb, J. Appl. Phys., 91, 5533, 2002. 47. Reid, M., and Fedosejevs, R., Terahertz emission from (100) InAs surface at high excitation fluences, Appl. Phys. Lett., 86, 011906-1, 2005. 48. Lewis, R. A., et al., Terahertz generation in InAs, Physica B, 376, 618, 2006. 49. Adomavicius, R., et al., Terahertz emission from p-InAs due to instantaneous polarization, Appl. Phys. Lett., 85, 2463, 2004. 50. Reid, M. and Fedosejevs, R., Terahertz emission from surface optical rectification in n-InAs, Proc. of SPIE, 5577, 659, 2004. 51. Ching, W. Y., and Huang, M. Z., Calculation of optical excitations in cubic semiconductors. III. Third-harmonic generation, Phys. Rev. B, 47, 9479, 1993. 52. Kang, H. S., et al., Technical digest of Pacific Rim conference on lasers and electro‑ optics. New York: IEEE, 1107, 1999.
7525_C002.indd 70
11/15/07 10:47:45 AM
Nonlinear Optical Techniques for Terahertz Pulse Generation and Detection 71 53. Liu, K., Xu, J., and Zhang, X. C., GaSe crystals for broadband terahertz wave detection, Appl. Phys. Lett., 85, 863, 2004. 54. Auston, D. H. and Cheung, K. P, Coherent time domain far-infrared spectroscopy, J. Opt. Soc. Am. B, 2, 606, 1985. 55. Han, P. Y., et al., Use of organic crystal DAST for terahertz beam applications, Opt. Lett., 25, 675, 2000. 56. Schneider, A., and Gunter, P., Spectrum of terahertz pulses from organic DAST crystals, Ferroelectrics, 318, 83, 2005. 57. Nahata, A., et al., Generation of terahertz radiation from a poled polymer, Appl. Phys. Lett., 67, 1358, 1995. 58. Khanarian, G., Mortazavi, M. A., and East, A. J., Phase matched second-harmonic generation from free standing periodically stacked polymer films, Appl. Phys. Lett., 63, 1462, 1993. 59. Hashimoto, H., et al., Characteristics of terahertz radiation form single crystals of N‑substituted 2-methyl-4-nitroaniline, J. Phys.: Condens. Matter, 13, L529,
2001. 60. Kuroyanagi, K., et al., All organic terahertz electromagnetic wave emission and detection using highly purified N-benzyl-2-methyl-4-nitroaniline crystals, Jpn. J. Appl. Phys., 45, 4068, 2006. 61. Carey, J. J., et al., Terahertz pulse generation in an organic crystal by optical rectification and resonant excitation of molecular charge transfer, Appl. Phys. Lett., 81, 4335, 2002. 62. Bailey, R. T., et al., The linear optical properties of the organic molecular crystal (+) 2(a-methylbenzylamino)-5-nitropyridine (MBA-NP), Mol. Cryst. Liq. Cryst., 231, 223, 1993. 63. Bailey, R. T., et al., Linear electrooptic dispersion in (-)-2-(a-methylbenzylamino)5‑nitropyridine single crystals, J. Appl. Phys., 75, 489, 1994. 64. Loffler, T., et al., Comparative performance of terahertz emitters in amplifier-laserbased systems, Semicond. Sci. Technol., 20, S134, 2005. 65. Siders, J. L. W., et al., Terahertz emission from YBa2Cu3O7-d thin films via bulk electric‑quadrupole-magnetic-dipole optical rectification, Phys. Rev. B, 61, 13633, 2000. 66. Hilton, D. J., et al., Terahertz emission via ultrashort-pulse excitation of magnetic metal films, Opt. Lett., 29, 1805, 2004. 67. Mikheev, G. M., et al., Giant optical rectification effect in nanocarbon films, Appl. Phys. Lett., 84, 4854, 2004. 68. Wu, Q., and Zhang, X. C., Ultrafast electrooptic field sensors, Appl. Phys. Lett., 68, 1604, 1996. 69. Wu, Q., and Zhang, X. C., Electrooptic sampling of freely propagating terahertz fields, Opt. Quantum Electron., 28, 945, 1996. 70. Han, P. Y., and Zhang, X. C., Coherent, broadband midinfrared terahertz beam sensors, Appl. Phys. Lett., 73, 3049, 1998. 71. Handbook series on semiconductor parameters, Levinstein, M., Rumyantsev, S., and Shur, eds., London: World Scientific, 1996, 1999. Available online at http://www. ioffe.rssi.ru/SVA/NSM/Semicond/. 72. Vosseburger, M., et al., Propagation effects in electrooptic sampling of THz pulses in GaAs., Appl. Opt., 37, 3368, 1998. 73. Wu, Q., and Zhang, X. C., Seven terahertz broadband GaP electrooptic sensor, Appl. Phys. Lett., 70, 1784, 1997. 74. Leitenstorfer, A., et al., Detectors and sources for ultrabroadband electrooptic sampling: experiment and theory, Appl. Phys. Lett., 74, 1516, 1999.
7525_C002.indd 71
11/15/07 10:47:46 AM
72
Terahertz Spectroscopy: Principles and Applications 75. Holzman, J. F., et al., Free-space detection of terahertz radiation using crystalline and polycrystalline ZnSe electrooptic sensors, Appl. Phys. Lett., 81, 2294, 2002. 76. Kubler, C., Huber, R., and Leitenstorfer, A., Ultrabroadband terahertz pulses: generation and field-resolved detection, Semicond. Sci. Technol., 20, S128, 2005. 77. Schneider, A., et al., Generation of terahertz pulses through optical rectification in organic DAST crystals: theory and experiment, J. Opt. Soc. Am. B, 23, 1822, 2006. 78. Nahata, A., and Cao, H., Broadband phase-matched generation and detection of terahertz radiation, Proc. SPIE, 5411, 151, 2004. 79. Shi, Y. Q., et al, Electrooptic polymer modulators with 0.8 V half-wave voltage, Appl. Phys. Lett., 77, 1, 2000. 80. Sinyukov, A. M., and Hayden, L. M., Generation and detection of terahertz radiation with multilayered electrooptic polymer films, Opt. Lett., 27, 55, 2002. 81. Van Tilborg, J., et al., Terahertz radiation as a bunch diagnostic for laser‑wakefield‑ accelerated electron bunches, Phys. Plasmas, 13, 56704–1, 2006. 82. Berden, G., et al., Electrooptic technique with improved time resolution for real time, nondestructive, single shot measurements of femtosecond electron bunch profiles, Phys. Rev. Lett., 93, 114802/1, 2004. 83. Wilke, I., Single-shot electron-beam bunch length measurements, Phys. Rev. Lett., 88, 124801/1, 2002. 84. Tsang, T., et al., Electrooptical measurements of picosecond bunch length if 45 MeV electron beam, J. Appl. Phys., 89, 4921, 2001. 85. Oepts, D., van der Meer, A. F. G., van Amersfoort, P. W., The free-electron-laser user facility FELIX, Infrared Phys. Techn., 36, 297, 1995. 86. Knippels, G. M. H., et al., Generation of frequency-chirped pulses in the far-infrared by means of a sub-picosecond free-electron laser and an external pulse shape, Opt. Commun., 118, 546, 1995. 87. Knippels, G. M. H., et al., Two-color facility based on a broadly tunable infrared free‑electron laser and a subpicosecond-synchronized 10-fs Ti:sapphire laser, Opt. Lett., 23, 1754, 1998. 88. Yan, X., et al., Subpicosecond electrooptic measurement of relativistic electron pulses, Phys. Rev. Lett., 85, 3404, 2000. 89. Ding, M., Weits, H. H., and Oepts, D., Coherent transition radiation diagnostic for electron bunch shape measurement at FELIX, Nucl. Instrum. Meth. A, 393, 504, 1997.
7525_C002.indd 72
11/15/07 10:47:47 AM
3
Time-Resolved Terahertz Spectroscopy and Terahertz Emission Spectroscopy Jason B. Baxter and Charles A. Schmuttenmaer Yale University
Contents 3.1 3.2
3.3
Introduction.................................................................................................... 74 Time-Resolved Terahertz Spectroscopy........................................................ 75 3.2.1 Introduction 3.2.2 History and Examples......................................................................... 77 3.2.3 Experimental Setup and Data Collection........................................... 78 3.2.3.1 Basic Requirements............................................................... 78 3.2.3.2 Detailed Description of Spectrometer................................... 79 3.2.3.3 Data Collection...................................................................... 81 3.2.3.4 Importance of Spot Size........................................................ 83 3.2.4 Data Workup.......................................................................................84 3.2.4.1 Calculating Conductivity......................................................84 3.2.4.2 Use of Complex Transmission Coefficients.......................... 88 3.2.4.3 Special Treatment at Short Pump-Delay Times....................92 3.2.4.4 Treatment of Porous Media................................................... 95 Terahertz Emission Spectroscopy..................................................................96 3.3.1 Experimental.......................................................................................97 3.3.1.1 Far Field versus Near Field................................................... 98 3.3.1.2 Terahertz Focusing Optics....................................................99 3.3.2 Data Analysis......................................................................................99 3.3.2.1 Sample Orientation.............................................................. 100 3.3.2.2 Excitation Polarization........................................................ 100 3.3.2.3 Emitted Waveform.............................................................. 100 3.3.3 Specific Examples............................................................................. 103 3.3.3.1 Photoconductive Switches................................................... 103 3.3.3.2. Shift Currents and Optical Rectification............................. 103
73
7525_C003.indd 73
11/15/07 10:50:00 AM
74
Terahertz Spectroscopy: Principles and Applications
3.3.3.3 Intramolecular Charge Transfer in Orienting Field............ 107 3.3.3.4 Demagnetization Dynamics................................................ 112 3.3.4 General Formalism........................................................................... 113 3.4 Conclusions.................................................................................................. 115 References............................................................................................................... 115
3.1 Introduction This chapter explores time-resolved aspects of THz spectroscopy. THz spectroscopy involves generating and detecting subpicosecond far-infrared (IR) pulses with an ultrafast visible or near-IR laser, as has been discussed in previous chapters. THz spectroscopy covers the region from 0.3 to 20 THz (10–600 cm–1), with most of the work being done between 0.5 and 3 THz. When converted to other units, 1 THz is equivalent to 33.3 cm–1 (wave numbers) or 0.004 eV photon energy or 300 µm wave length. For example, the THz region is ideal for probing semiconductors because the frequency range closely matches typical carrier scattering rates of 1012 to 1014 s–1, allowing for more accurate modeling of the photoconductivity data. In conventional benchtop experiments, THz pulses are created and detected using short-pulsed Ti:sapphire lasers with pulsewidths ranging from ~100 fs to ~10 fs. The pulsed light allows time-resolved THz studies, in contrast to continuous sources of far-IR radiation such as arc lamps or globars. Pulsed sources such as free electron lasers or synchrotrons have also recently achieved subpicosecond pulse duration, but these are large, expensive user facilities and are less accessible than a Ti:sapphire laser in an individual laboratory. THz spectroscopy also has the advantage that it measures the transient electric field, not simply its intensity.1 Coherent detection allows direct determination of both the amplitude and the phase of each of the spectral components that make up the pulse. The absorption coefficient and refractive index of the sample are computed from the amplitude and phase. Thus the complex-valued permittivity of the sample is obtained without requiring a Kramers-Kronig analysis. The great majority of the results reported in the literature that use conventional far-IR sources and detectors present the frequency-dependent absorption coefficient, but not the refractive index. In this respect, THz spectroscopy provides a convenient method for determining the complex permittivity, even for studies that are not time-resolved. There are three categories of commonly performed experiments: THz time domain spectroscopy (THz-TDS), time-resolved THz spectroscopy (TRTS), and THz emission spectroscopy (TES). The information obtained in a THz-TDS experiment is equivalent to that obtained from a frequency domain linear absorption spectrometer, for example, an FTIR. THz-TDS made its debut in 1988–1989, and the majority of THz work done to date has been along these lines. There are distinct advantages of the THz-TDS method over frequency domain methods, as discussed in detail in Chapter 1. However, the present chapter concerns time-resolved experiments, and THz-TDS need not be considered further. Aside from a small number of initial studies,2–8 most of the development of TRTS has taken place since the year 2000. In contrast to a standard THz-TDS experiment,
7525_C003.indd 74
11/15/07 10:50:01 AM
Time-Resolved Terahertz Spectroscopy
75
this type of experiment is somewhat more difficult to perform and analyze. In TRTS, the sample is typically photoexcited with a laser pulse (with wavelength ranging from near-IR to ultraviolet) and the time-dependent THz spectrum is obtained with the THz probe pulse. The THz spectrum can be obtained at times ranging from less than 100 fs to more than 1 ns after photoexcitation. This method is sometimes referred to as optical pump/THz probe spectroscopy, but that designation is too limiting. One need not pump optically to make a time-resolved measurement, although the examples given in this chapter all employ optical excitation. TRTS differs from THz-TDS at a very fundamental level. THz-TDS provides information about the static properties of the sample, but TRTS probes the dynamic, evolving properties of the material. For example, the THz transmission of a material depends strongly on how well it conducts electricity. In fact, TRTS is a noncontact electrical probe with subpicosecond temporal resolution, and the behavior of undoped semiconductors on photoexcitation has been studied in great detail as they switch from insulating to conducting. THz emission spectroscopy, TES, has been carried out for as long as THz-TDS has. To perform THz-TDS, it is necessary to generate THz pulses before sending them through the sample under study. However, in that capacity, one is not trying to learn about the material that generates the THz pulses, but is simply using it as a source of THz radiation. In contrast, TES refers to the situation where one is trying to understand the properties of the material being studied by analyzing the shape and amplitude of the THz waveform emitted. It is basically a THz-TDS setup in which the sample itself is the THz emitter. Over the years, semiconductors, superconductors, heterostructures, oriented molecules in solution, and magnetic films have all been studied with this method. All of these methods (THz-TDS, TRTS, and TES) take advantage of one or more of the unique characteristics of THz spectroscopy. The time-dependent electric field is measured (rather than its intensity). These are very bright far-IR sources, and the detectors employed have certain advantages over standard far-IR detectors as well. Most important, however, is the ability to carry out time-resolved experiments in the far-IR region of the spectrum with subpicosecond time resolution.
3.2 Time-Resolved Terahertz Spectroscopy 3.2.1 Introduction TRTS is a noncontact electrical probe capable of determining the complex-valued, frequency-dependent, far-IR permittivity with a temporal resolution of better than 200 fs. TRTS is used to study the changes in a material’s permittivity upon photoexcitation with an optical pump pulse. Changes in the permittivity arise from phenomena such as the photoinduced creation of mobile electrons and holes, polarizable excitons, and polarons. We will refer to “photoconductivity” as the change in sample permittivity upon photoexcitation, although conductivity does not necessarily arise from electronic conduction. Knowledge of a material’s frequency-dependent photoconductivity is important for its use in electronic and optoelectronic devices. Furthermore, the ability to characterize electrical properties in a noncontact fashion
7525_C003.indd 75
11/15/07 10:50:02 AM
76
Terahertz Spectroscopy: Principles and Applications τpp
Sample
Figure 3.1 Schematic illustration of time-resolved THz spectroscopy experiment. The sample is photoexcited with an optical pump pulse and probed at a time, τpp, later with a THz pulse. The sample attenuates and delays the THz pulse according to its complex permittivity.
is critical in the study of nanomaterials, where it can be difficult or impossible to make electrical measurements using conventional probes. The intensity of the THz transmission change after photoexcitation is, in most cases, proportional to both the photoexcited carrier density and mobility. This is in contrast to methods such as transient absorption or time-resolved luminescence, which are sensitive to either the sum or the product of the electron and hole distribution functions, respectively. Additionally, luminescence methods are limited to direct gap semiconductors, whereas TRTS can be used to study carrier dynamics in both direct and indirect gap materials. Even methods that are sensitive to the diffusion of carriers, such as transient grating or four-wave mixing, are not able to determine the frequency-dependent conductivity. TRTS has high sensitivity to mobile electrons. For example, it can measure photoexcited carrier column densities as low as 5 × 1010 cm–2 in GaAs (equivalent to a carrier density of 5 × 1014 cm–3 with a skin depth of 1 µm). Because TRTS measures the sample permittivity, it is sensitive not only to mobile electrons and holes, but also to quasiparticles such as excitons and polarons. The different signatures of these particles in the frequency domain allow one to distinguish the source of permittivity changes using a combination of TRTS and appropriate models. Several different types of experiments make use of the subpicosecond pulses in the far-IR region of the spectrum. In each case, the sample is excited with an optical pulse and then probed with a terahertz pulse as shown in Figure 3.1. So-called “pump scans” monitor a single point on the THz waveform (or the integrated power using a bolometer) and vary the pump probe delay time to measure the average response of the material. In this way, it is possible to characterize the average far-IR response to an optical perturbation. One can measure the overall change in transmission as well as the time scales for the material to respond and to return to its equilibrium state. A second technique, often called a probe scan, is used to record the entire THz wave form at a fixed delay time after photoexcitation. This method obtains the frequencydependent, complex-valued photoconductivity. Finally, the most comprehensive type of study is to create a two-dimensional (2D) grid that maps out the THz waveform at many pump delay times. Although average response and fixed pump delay studies
7525_C003.indd 76
11/15/07 10:50:05 AM
Time-Resolved Terahertz Spectroscopy
77
are quite useful, the maximum amount of information is obtained from a 2D study in which the photoconductivity can be determined as a function of both frequency and delay time. This method is often referred to as optical pump/THz probe spectroscopy or time-resolved THz spectroscopy. Many different materials systems have been investigated using TRTS. Carrier dynamics in bulk and nanostructured semiconductors, superconductors, and strongly correlated electron systems have been topics of recent research. A very brief accounting of some initial and more recent studies is given below to demonstrate some of the different phenomena that can be observed with TRTS, and other examples will be discussed in detail in subsequent chapters. The remainder of this section describes the experimental apparatus, collection of data, and analysis of data. It points out the common assumptions made during the interpretation of data as well as methods of dealing with possible pitfalls or artifacts.
3.2.2 History and Examples The methods of data collection and analysis used in TRTS were first extensively tested on the well-characterized GaAs system in the late 1990s. A <100> gallium arsenide (GaAs) wafer was shown to have frequency-dependent photoconductivity that follows the Drude model and mobilities that match well with those determined by other experimental techniques.9 Carrier injection time was a function of optical pump wavelength. High-energy photons can excite electrons into low mobility valleys in the conduction band. Carriers scatter and relax into lower energy, high mobility regions of momentum space, resulting in an increase in THz absorbance. In low temperature-grown GaAs (LT-GaAs) thin films, the electron lifetime was found to be only 1.1 ps,10 compared with hundreds of picoseconds in GaAs,9 because of the increased recombination rates arising from higher defect densities. Mobility in lowtemperature-GaAs is also a factor of two lower than in GaAs single crystals. The mobilities determined in these studies could be compared with those from electrical measurements, with TRTS contributing previously unobtainable information at very short time scales. After the techniques of TRTS had been benchmarked using bulk samples with well-characterized electrical properties, its noncontact nature could be exploited to study semiconductor nanomaterials such as nanowire arrays and nanoparticle films. Although it is cumbersome to make contacts to and electrically characterize individual nanowires, TRTS allows characterization of a nanowire array without having to remove the nanowires from the substrate. In cases such as these, an appropriate effective medium theory must be taken into account. Conductivities of InP,11 CdSe,12,13 TiO2,14,15 and ZnO nanoparticle films16 and in ZnO nanowire arrays16 have been studied. In addition to studying carriers generated by bulk absorption of photons with energy larger than the semiconductor bandgap, TRTS is also sensitive to electrons injected into the semiconductor from adsorbed dye molecules.14,15 TRTS can be combined with transient absorption spectroscopy to gain detailed insight into interfacial electron transfer processes. In addition to detecting mobile electrons as in the above systems, TRTS is also sensitive to polarizable excitons. TRTS has given unprecedented information on the
7525_C003.indd 77
11/15/07 10:50:06 AM
78
(a)
4
(b)
2 0
0 –4
4
–2 τ = 15 ps 0.5
τ = 200 ps 0.5
1.0
–4 1.0
σ0 (ω, τ = 200 ps) (10–1 S/m)
σ0 (ω, τ = 15 ps) (S/m)
Terahertz Spectroscopy: Principles and Applications
ω (THz)
Figure 3.2 Conductivity of a ZnO wafer (a) 15 ps and (b) 200 ps after 400 nm photoexcitation. Open and closed circles are the real and imaginary components, respectively, of the complex conductivity. In (a), the response is dominated by free electrons and holes and is well-described by the Drude model (lines). In (b), excitons dominate the response, with lines modeling exciton polarizability. (Figure reprinted with permission from Hendry, E., Charge dynamics in novel semiconductors, Ph.D. thesis, 2005.)
time scales for exciton formation from free electrons and holes in systems such as single crystal ZnO wafers,17 carbon nanotubes,18 and semiconducting polymers.19–21 A dominant positive real conductivity indicates the presence of mobile free carriers, whereas a strong negative imaginary conductivity can be indicative of excitons, as shown in Figure 3.2. Simultaneous detection of both free carriers and bound excitons is another advantage of TRTS.
3.2.3 Experimental Setup and Data Collection 3.2.3.1 Basic Requirements The fundamental requirement of TRTS is the generation of synchronized optical pump and THz probe pulses. Figure 3.1 shows a sample being photoexcited with an optical pulse and subsequently probed with a THz pulse. Varying the delay time between the pump and probe pulses allows study of many different processes including carrier injection, cooling, decay, and trapping. Depending on the pulse energy and wavelength desired, these pulses could be provided from sources such as unamplified or amplified Ti:sapphire lasers or synchrotrons. Amplified Ti:sapphire laser systems are the most commonly used, as they can provide high energy, sub-100-fs pulses at kHz repetition rates with wavelengths tunable by nonlinear optics and optical parametric amplifiers. A detailed description of the amplified Ti:sapphire TRTS spectrometer used in the Schmuttenmaer lab is given in the following section. For samples that exhibit a large change in THz transmission per fundamental Ti:sapphire photon and whose longest time constants are on the order of nanoseconds, it is possible to perform TRTS with an 82-MHz Ti:sapphire oscillator alone. Samples requiring very high photon flux can be investigated using free electron lasers or synchrotron sources.
7525_C003.indd 78
11/15/07 10:50:09 AM
79
Time-Resolved Terahertz Spectroscopy Ti: Sapphire Regenerative Amplifier 1 kHz, 100 fs, 1W Average Power
(a)
(c)
(b)
(f )
(p) (o) (l)
Chopper Pos. 1 (h)
(n)
(i)
Pump Beam
2
(m)
1
(q)
(k)
THz Beam
Lock-in Amplifier
(j) (e)
Chopper Pos. 2 (d)
(g)
Detector Beam
Oscilloscope
3
Computer
Figure 3.3 Time-resolved THz spectrometer. (a) Galilean telescope reduces the laser beam waist, (b) beam splitter, (c) optional frequency doubling crystal, (d) pump beam delay table, (e) optional lens, (f) dielectric mirror (99/1 beam splitter), (g) generator delay table, (h) 800-nm λ/2 waveplate, (i) 1-mm <110> ZnTe crystal, (j) four off-axis parabolic mirrors, (k) sample position, (l) 0.5-mm <110> ZnTe crystal, (m) detector delay table or galvanometer, (n) polarizer, (o) 800-nm λ/4 waveplate, (p) Wollaston polarizing beam splitter, and (q) balanced photodiodes. The balanced photodiodes are output to a lock-in amplifier.
3.2.3.2 Detailed Description of Spectrometer Figure 3.3 displays a detailed schematic of a typical TRTS spectrometer. This particular design has been employed in the Schmuttenmaer laboratory at Yale University, but many variations are possible. A Spectra Physics regenerative amplifier system (Millennia-Tsunami-Merlin-Spitfire) produces a 1-kHz pulse train of 800 µJ, 800 nm pulses of 100-fs duration (full width at half maximum). There are three arms of the spectrometer: THz generation, THz detection, and optical photoexcitation. Roughly two thirds of the light is used as the optical pump beam, whereas the other third generates and detects the THz radiation. The beam for the THz probe is split into a
7525_C003.indd 79
11/15/07 10:50:11 AM
80
Terahertz Spectroscopy: Principles and Applications
collimated 2-mm diameter near-IR beam of 250 µJ/pulse for THz generation and a focused 200-µm diameter near-IR beam of 5 nJ/pulse for THz detection. The intensity of the optical pump beam can be varied to a maximum of ~500 µJ/pulse for 800-nm excitation, ~200 µJ/pulse for 400-nm light, or lower energies for other wavelengths generated by an optical parametric amplifier. The pump spot size is usually between 5–10 mm diameter, but can be adjusted depending on the experimental requirements. The following list describes each component of the TRTS spectrometer shown in Figure 3.3. (a) A Galilean telescope (one focusing and one diverging lens) used to reduce the laser beam waist by a factor of two and collimate the beam. (b) 70:30 beam splitter (Melles Griot). Pump arm (c) 1-mm thick β-BaB2O4 crystal (Quantum Technology Inc.) for experiments requiring second harmonic generation to produce 400-nm excitation. (d) Optical delay table (Parker-Daedal) for pump arm of spectrometer. (e) Optional lens for expanding the pump-beam diameter. THz generation arm (f) A dielectric mirror that acts as a 99:1 beam splitter. The reflected beam generates the THz pulse and the transmitted beam is used to detect the THz pulse. (g) Optical delay table (Parker-Daedal) for THz generation arm of spectrometer. (h) A λ/2 waveplate (Melles Griot) that rotates the vertically polarized 800-nm beam before optical rectification; the output THz beam is polarized horizontally. (i) THz generator crystal, usually a 1-mm thick <110> ZnTe single crystal (eV Products) mounted in a rotation stage. The crystal axis is rotated relative to the polarization axis of the visible pulse to maximize THz generation. (j) Four off-axis parabolic mirrors, (Melles Griot O2 POA 017). Mirror 1 collimates the diverging THz beam, Mirror 2 refocuses the beam onto the sample, Mirror 3 recollimates it, and Mirror 4 focuses it onto the detector crystal. Mirror 4 has a shorter focal length (38.1 mm) than the others (119 mm). Mirrors 2 and 4 have small holes drilled in them to allow transmission of the pump and detector beams, respectively. (k) Sample position. (l) A 0.5-mm thick (110) ZnTe crystal (eV Products) used to detect the THz pulses by free space electrooptic sampling. THz detection arm (m) Galvanometer (General Scanning) for detector arm of spectrometer. (n) 800-nm polarizer (Polacor). (o) A λ/4 waveplate (Melles Griot) to balance the detectors while THz is blocked.
7525_C003.indd 80
11/15/07 10:50:11 AM
81
Time-Resolved Terahertz Spectroscopy
(p) Wollaston polarizing beam splitter (Karl Lambrecht) to send horizontal and vertical polarizations to different photodiodes. (q) Balanced large-area silicon photodiodes (ThorLabs) for signal detection. The voltages from the photodiodes are directed to a lock-in amplifier which measures the difference in their voltages. Coherent detection allows pulses below the blackbody radiation level to be measured without the use of specialized detectors. A computer interfaces with the experiment by controlling the delay tables and the lock-in amplifier. 3.2.3.3 Data Collection
Electric Field (a.u.)
Time domain scans are collected by scanning the probe delay line (delay line 2 in Figure 3.3) with the pump beam blocked and the chopper in position 1 in Figure 3.3. Figure 3.4 shows THz time domain scans with and without a sample in the THz beam path. Introducing a sample delays, disperses, and attenuates the THz wave form. Methods of extracting the absorbance and refractive index from the THz wave forms are described in the Section 3.2.4. Photoexcitation causes a change in transmission of the sample. For example, photoexcitation of many semiconductors generates free carriers that absorb THz radiation, resulting in a decrease in transmission. The transmission change is a function of both the delay time between the optical pump and THz probe and the time point on the THz waveform. Figure 3.5 shows a 2D grid of the transmission change as a function THz delay time and pump probe delay time.22 These data can be visualized either as a three-dimensional plot or as contour lines projected onto the pump delay–THz delay plane. Taking projections of the 2D grid allows us to measure the dynamics of an experiment. A cut parallel to the pump-delay axis is a 1D pump scan, and a cut parallel to the THz delay axis is a 1D probe scan. The 1D pump scans give the average THz absorption as a function of pump delay time. By Fourier transforming the 1D probe scans, we obtain the frequency-dependent optical constants of the photoexcited material at a given time after photoexcitation.
10 8 6 4 2 0 –2 –4 –6
Reference Sample
–4
–2
0
2
4
6
Time (ps)
Figure 3.4 Time domain scans of a terahertz pulse with and without a sample, in this case a ZnO wafer, at the focus of the terahertz beam. The sample delays, disperses, and attenuates the pulse.
7525_C003.indd 81
11/15/07 10:50:13 AM
82
Terahertz Spectroscopy: Principles and Applications 1 D Pump Scan
Pump-Delay (ps)
3
1D Probe Scan
2 1 0 –1 1
2 3 THz Delay (ps)
4
Figure 3.5 Contour plot of THz difference scan of low-temperature-GaAs photoexcited at 400 nm solid lines represent negative values, whereas dashed lines correspond to positive values. Because the far-infrared response is slower when photoexcitation occurs at 400 nm compared with 800 nm, there is no need for detector deconvolution. One-dimensional (1D) cuts can be taken from the data: 1D pump scans are parallel to the pump delay axis and 1D probe scans are parallel the THz delay axis. (Figure reprinted with permission from Beard, M.C. et al., J. Appl. Phys., EPAPS, 90, 5915, 2001. Copyright 2000 by the American Institute of Physics.)
We can obtain these 1D cuts experimentally by fixing one delay line and scanning the other. We collect the 2D grid by collecting a series of 1D probe scans at a series of pump delay times. Pump scans are taken by fixing the THz delay (line 2) at the peak of the photoexcited THz waveform and scanning the pump delay (line 3) while chopping the optical pump beam (position 2 in Figure 3.3). By chopping the pump beam, we measure the difference between the photoexcited and non-photoexcited THz transmission through the sample. Figure 3.6a shows an 800-ps pump scan for a ZnO thin film, with the inset showing a 16-ps pump scan. Pump scans taken over the time immediately bracketing the optical pump are useful in determining the time constants of electron photoinjection, whereas long-time pump scans can be used to measure the decay dynamics of the photoexcited electron population. In this example, there is a fast injection component in the subpicosecond regime and a slower injection component on the 5-ps time scale. The long-time pump scan is very flat, indicating that the photoexcited electron population and mobility remain constant at higher than 800 ps. “Difference scans” are probe scans taken by fixing the pump delay (line 3) and scanning the THz delay (line 2) while chopping the optical pump beam. Figure 3.6b shows a difference scan for a ZnO wafer, the reference and sample THz scans of which are shown in Figure 3.4. The magnitude of the difference waveform is less than 10% of the sample THz waveform, allowing the photoexcitation to be treated as a small perturbation to the system. In many semiconductors, photoexcitation generates free carriers that absorb THz radiation. Therefore the transmission decreases on photoexcitation and the shape of the difference waveform resembles the negative THz waveform. Because the photoconductivity is determined by the difference between the photoexcited and nonphotoexcited waveforms, it is most accurate to measure this difference directly with the chopper in the pump beam path rather than
7525_C003.indd 82
11/15/07 10:50:15 AM
83
Norm. Transmission
Time-Resolved Terahertz Spectroscopy 0.0
0.0 –0.2 –0.4 –0.6 –0.8 –1.0 –4
–0.2 –0.4 –0.6 –0.8
0
4
8
12
–1.0 0
200
400
800
600
Time (ps)
Electric Field (a.u.)
(a) 0.2 0.0 –0.2 –0.4 –0.6 –6
–4
–2
0
2
4
6
Time (ps) (b)
Figure 3.6 (a) Pump scans for a ZnO thin film. The inset shows injection at short pump– probe delay times and the main panel shows that the signal does not decay over 800 ps. (b) Difference scan, ∆ETHz (pump-on minus pump-off), taken 20 ps after photoexcitation of a ZnO wafer. Note the similar shape, but opposite sign and smaller magnitude, to the associated non-photoexcited THz waveform shown in Figure 3.4.
to measure the THz waveform with the chopper in position 1 both with and without pumping. 3.2.3.4 Importance of Spot Size To avoid frequency-dependent artifacts, it is important that the THz probe samples a region of uniformly photoexcited material. Therefore, the spot size of the visible (pump) beam should be least two times larger than that of the THz (probe) beam. The parabolic mirrors focus the THz probe at the sample to a spot size of approximately 3 mm, but higher THz frequencies are focused more tightly than lower frequencies. As a result, the extracted spectrum is skewed to higher frequencies when the spot size (the diameter at which the intensity of a Gaussian beam falls to 1/e2 of its value at the beam center) of the pump is the same size or smaller than the THz probe, as shown in Figure 3.7. If higher pump intensities are needed, then a smaller diameter pump beam can be used in conjunction with an iris at the sample. The iris blocks THz radiation that would have passed through nonphotoexcited regions of the sample. Additionally, the THz and visible beams should be copropagated to minimize temporal smearing.
7525_C003.indd 83
11/15/07 10:50:17 AM
84
∆(OD) (arb. units)
Terahertz Spectroscopy: Principles and Applications
0.3 0.2 0.1 0.0
0
1
2
Frequency (THz)
Figure 3.7 Change in optical density spectra of photoexcited GaAs as a function of visible (pump) spot size at a 20-ps pump–probe delay time. The visible spot sizes are 6.0 mm (solid line), 1.7 mm (dashed line), and 1.1 mm (dot dashed line), whereas the THz spot size is 2.3 mm. The spectrum becomes skewed toward higher frequencies as the visible spot size becomes smaller than the THz spot size. (Figure reprinted with permission from Beard, M.C. et al., Phys. Rev. B, 62, 15766, 2000. Copyright 2000 by the American Physical Society.)
3.2.4 Data Workup 3.2.4.1 Calculating Conductivity A THz waveform can be Fourier transformed to give the frequency-dependent, complex-valued permittivity. The frequency-dependent, complex-valued photoconductivity, σˆ , is obtained from
ˆ ˆ (w ) = eˆ (w ) + iσ(w ) , η e 0w
(3.1)
ˆ is the photoexcited permittivity, eˆ is the nonphotoexcited permittivity, w where η is the angular frequency, e0 is the free-space permittivity, and i is the unit imaginary. The photoconductivity refers to the response induced by the photoexcitation. This response could arise from a variety of sources such as mobile electrons (holes) excited into the conduction (valence) band of a semiconductor, polarizable excitons, polaritons, or other quasiparticles. Prior knowledge of the sample properties combined with careful experiments can determine the source of the conductivity. Determination of the conductivity from the data does not require any model, although models can later be fit to the data to extract relevant parameters about the system. Depending on the degree of accuracy required and the validity of certain assumptions, calculating permittivity and conductivity from THz waveforms can range from fairly simple to rather complex. If we assume that no THz radiation is reflected at any of the sample interfaces such that all THz is either transmitted or absorbed, the sample permittivity can be calculated in a straightforward way from the Fourier transform of the reference and sample scans shown in Figure 3.4. The power and phase, calculated from the Fourier transform of the time domain scans, are shown as a function of frequency in Figure 3.8. Because the phase is determined using the arctan, it can only be determined in the range (–π, π), resulting in a saw
7525_C003.indd 84
11/15/07 10:50:22 AM
85
Power (a.u.)
Time-Resolved Terahertz Spectroscopy 10–3 10–4 10–5 10–6 10–7 10–8 10–9 10–10 10–11
Ref Sample
0
1
2
3
4
3
4
Frequency (THz) (a)
Phase (rad)
200
π
150
0 –π
100
Sample 1
2 Ref
50 0
0
1
2 Frequency (THz) (b)
Figure 3.8 (a) Power and (b) phase of a reference and sample pulse calculated from the time domain scans in Figure 3.4. The inset in (b) shows the reference phase before correcting for discontinuities.
tooth behavior with increasing frequency. The discontinuities should be removed to facilitate later calculations and for ease of visualization by adding 2π at each point of discontinuity. This process smooths the phase to a continuously increasing function without loss of information and allows ∆φ to be determined properly. Additional factors of 2π may also need to be added to the sample phase at all frequencies for thick or high index samples. The absorbance and refractive index of the sample are related to the power, P, and phase, f, of the Fourier transform of the sample and reference scans by a=
1 P ln d P0
(3.2)
and
n = 1+
7525_C003.indd 85
c (φ - φ 0 ). 2 pwd
(3.3)
11/15/07 10:50:25 AM
86
Terahertz Spectroscopy: Principles and Applications
Absorbance (1/cm)
50 40 30 20 10
Refractive Index
0 0.2
0.4
0.6
0.8 1.0 Frequency (THz) (a)
0.4
0.6
1.2
1.4
1.2
1.4
3.4 3.2 3.0 2.8 2.6 0.2
0.8
1.0
Frequency (THz) (b)
Figure 3.9 (a) Absorbance and (b) refractive index of a ZnO wafer calculated using Equations 3.2 and 3.3 and the power and phase data in Figure 3.8. In this case, transmission losses are actually the result of reflection, but they appear as absorbance because of the assumptions in this simplistic procedure. Using complex transmission coefficients as described in Section 3.2.4.2 will remove this “absorbance offset.”
Figure 3.9 shows the absorbance and refractive index calculated using Equations 3.2 and 3.3 along with the power and phase data from Figure 3.8. The complex- valued permittivity and the complex-valued refractive index are related through eˆ = nˆ 2 where nˆ = n + ik , and k = λa / 4 p = c a / 2w. Thus the real and imaginary components of the permittivity are determined from a and n through
e′ = n2 - k 2
(3.4)
e ′′ = 2nk .
(3.5)
and
Photoconductivity can then be calculated from Equation 3.1 by using the photoexcited permittivity as the generalized permittivity, ηˆ , and the non-photoexcited permittivity as the static permittivity, eˆ . The real and imaginary parts of the
7525_C003.indd 86
11/15/07 10:50:30 AM
87
Time-Resolved Terahertz Spectroscopy
photoconductivity are given by
σ ′ = e 0w ( η′′ - e ′′)
σ ′′ = e 0w (e ′ - η′).
(3.6) (3.7)
Example photoconductivities are plotted in Figure 3.2 for a ZnO wafer at 30 K at two pump delay times.17 At short times, the photoconductivity is well fit by the Drude model for free electrons, whereas at long times, the photoconductivity has the signature of excitons. The free electrons and holes become bound as excitons on the 50-ps timescale. ˆ is the photoIt is important to note that the measured change in conductivity, σ, conductivity and not the overall conductivity of the sample when using this method. In the case in which the change on photoexcitation is small, it is useful to measure the “difference scan” directly by placing the chopper in the pump beam as discussed in the experimental methods section. Hence, ∆E(t) = Ep* (t) – Enp(t) is measured and added to the measured nonphotoexcited THz waveform Enp(t) to yield the photoexcited waveform Ep* (t). An alternative method has been presented by Heinz et al. for samples with ∆E(t) << Enp(t).23 This method neglects multiple reflections, whose influence is slight in most cases. From Maxwell’s equations, they derive
wd eˆ eˆ - eˆ ext Deˆ = 2eˆ i c eˆ + eˆ ext
-1
DE (w ) × E (w )
(3.8)
for the photoinduced change in permittivity, where ∆E(w) and E(w) are the Fourier transforms of the difference scan and the nonphotoexcited THz scan, respectively. eˆ and eˆ ext are the frequency-dependent, complex permittivities of the nonphotoexcited sample and its surrounding material, respectively, and d is the thickness of the photoexcited material. Again, both of these methods ignore reflections at the sample interfaces. To treat such reflections requires the introduction of complex transmission coefficients. Two mathematically convenient methods of dealing with complex transmission coefficients are outlined in Section 3.2.4.2. These methods are useful for dealing with reflections from a single layer, from a multilayered sample, or from a sample that has been partitioned into slabs of varying conductivity that arise due to absorbance that varies according to Beer’s law. When the sample thickness is small compared with the optical skin depth, one can assume uniform absorption throughout the sample. However, when the optical skin depth is smaller than the sample thickness, it is appropriate either to define a photoexcited layer and a nonphotoexcited layer or to define many layers of exponentially decreasing conductivity.
7525_C003.indd 87
11/15/07 10:50:35 AM
88
Terahertz Spectroscopy: Principles and Applications
These methods also assume that the conductivity changes slowly over the time that the THz probe interacts with the sample, which is approximately 1 ps. This constraint is often met for pump–probe delay times greater than 3 ps. Additionally, because the optical pump pulse is approximately of 100-fs duration and the probe pulse is approximately 1 ps, at short times the beginning of the THz wave probes nonphotoexcited material, whereas the end of the THz wave probes photoexcited material. In this case, the beginning of the THz wave sees different sample properties than the end, leading to data that can be misleading if not treated appropriately. Scanning a 2D grid of pump–probe data and deconvolving the detector response function allow correct interpretation of data at short pump delay times, as described in detail in Section 3.2.4.3. 3.2.4.2 Use of Complex Transmission Coefficients Many systems studied with TRTS are layered stacks of dielectric materials. The dielectric stack could consist of semi-infinite layers of air that surround a thin film on a substrate, or, in the case of a photoexcited semiconductor whose optical skin depth is less than its own thickness, could consist of photoexcited and non- photoexcited semiconductor. The frequency-dependent absorption coefficient ap(w) and refractive index np(w) of the photoexcited sample can be extracted directly from the measured data without assuming a model to describe the medium. Extraction of ap(w) and np(w) requires knowing the photoexcited path length d and the reflectivity losses at all the interfaces, but reflectivity is not known a priori when the material permittivity is unknown. Furthermore, the photoexcited path length is not well defined because the photoexcited medium gradually transforms into the nonphotoexcited medium. In strongly absorbing materials, the photoexcited path length d is small compared with the spatial extent of the THz pulse. This can result in interface effects that, if not treated correctly, can lead to large errors in determining the optical properties. The interface effects are most pronounced when photoexcitation causes large changes in np(w) and can even cause apparent superluminal propagation through photoexcited materials.2, 9 Photoexcitation creates an exponentially decreasing concentration of carriers as a function of distance into the sample. The spatial distribution of carriers evolves over time as the excited carriers diffuse and recombine at the surface and in the bulk, and diffusion and recombination can be modeled to determine the carrier spatial distribution at any given pump delay time.9 In most cases, diffusion is only important at longer pump delay times when t >do2/D, where D is the diffusion coefficient and do is the initial photoexcited path length. As a first approximation, the photoexcited distribution can be treated as a uniform slab with thickness d which is chosen to be the optical skin depth for exponential carrier distributions. For nonexponential distributions, the slab thickness is determined by normalizing the distribution such that its maximum is unity with the integral of the normalized distribution giving the appropriate thickness, d. Beard and Schmuttenmaer have performed finite difference time domain (FDTD) simulations of TRTS experiments using different non-uniform spatial distributions to understand conditions under which the slab approximation holds24 and found that it is valid when the spatial extent of the distribution is less than approximately 5 µm.
7525_C003.indd 88
11/15/07 10:50:37 AM
89
Time-Resolved Terahertz Spectroscopy
After a scheme for relating the conductivity profile to the absorbance of the optical pump has been developed, we can then address the formalism of treating the dielectric stack. The basic premise is to determine the permittivity of each layer such that when THz light is propagated through the entire dielectric stack, the calculated transmittance equals the measured transmittance. Measured TRTS data can be directly transformed to determine the complex ratio of the THz field with pump on (photoexcited) versus pump off (nonphotoexcited):
qmeas = E p* (w , d ) / E np (w , d )
(3.9)
where Ep* (w,d) is the complex field measured after transmission through the photoexcited material, and Enp(w,d) is the field measured after transmission through the nonphotoexcited material. Enp(w,d) and Ep* (w,d) are the Fourier transforms of the time domain data, where the THz difference pulse ∆E(t,d) = Ep* (t,d) – Enp(t,d) is measured and added to Enp(t,d) to yield Ep* (t,d). Treating the interfaces in the dielectric stack is accomplished by relating qmeas to a complex transmission amplitude coefficient z(k), which accounts for the reflectivity of each interface as well as propagation through the structure. The transmission coefficient relates the complex transmitted electric field amplitude A tr(w,d) to the complex initial electric field amplitude25 Ao(w,0) as
Atr (w, d ) = z( k ) A0 (w, 0 ).
(3.10)
To be general, E = A exp(ikz – iwt) where E is the full complex electric field, A is the complex amplitude, and k is the complex wave vector given by k (w ) =
2 pn(w ) a (w ) +i . λ 2
(3.11)
The far-IR optical properties of the photoexcited material can be calculated directly from qmeas and the nonphotoexcited optical properties via the complex transmission amplitude coefficients of the photoexcited zp* (k p*) and nonphotoexcited znp(knp) media. From Equations 3.9 and 3.10, qmeas =
z*p (kp* ) . znp ( knp )
(3.12)
Separate non–time-resolved measurement of the far-IR optical properties of the nonphotoexcited material give the nonphotoexcited transmission coefficient znp(k np). By inverting Equation 3.12 and combining it with an appropriate equation for zp* (k p*), discussed later in this chapter, we can obtain the wave vector for the photoexcited medium k p*, and thus the photoexcited optical constants a(w) and n(w). The inversion can be done numerically by generating a grid of |q(aguess, nguess) – qmeas | and finding the minimum on the grid or by other numerical procedures for solving these
7525_C003.indd 89
11/15/07 10:50:41 AM
90
Terahertz Spectroscopy: Principles and Applications
equations, such as the Newton-Raphson method. The photoconductivity can be found from a and n for the photoexcited and nonphotoexcited material using the procedure in Section 3.3.4.1. Several methods exist for the calculation of the transmission coefficient for a dielectric stack. Transfer matrices provide an intuitive approach to developing the equations to describe propagation through a dielectric stack and thereby calculate the transmission coefficient z(k).26 First, consider a single layer with refractive index n1 sandwiched between two semi-infinite media with refractive indices of n 0 and nT, respectively. The equation describing propagation through this layer single layer is given in matrix form by26
1 1 A0′ cos kd = + n0 - n0 A0 - in sin kd 1
-i sin kd n1 cos kd
1 AT , nT A0
(3.13)
where d is the layer thickness, and k is the wavevector in the layer, k = 2pn1/l0. Letting the reflection and transmission coefficients be r = A0′ / A0 and z = AT / A0 , respectively, allows Equation 3.13 to be written more compactly as 1 1 r =M + n0 - n0
1 z , nT
(3.14)
where M is the transfer matrix. For multiple layers, the overall transfer matrix M becomes the product of the individual layer’s transfer matrices, such that
A M 1M 2M 3 ... M N = M = C
B . D
(3.15)
For the situation shown in Figure 3.10a, where there is a photoexcited layer and a nonphotoexcited layer, we have cos k1d1 M = M 1M 2 = - in1 sin k1d1
-i sin k1d1 n1 cos k1d1
cos k 2d 2 - in2 sin k 2d 2
-i sin k 2d 2 n2 . cos k 2d 2
(3.16)
Combining Equations 3.14 and 3.16, and solving for the transmission coefficient yields26 z=
2n0 . An0 + BnT n0 + C + DnT
(3.17)
Finally, the complex refractive index of the photoexcited layer, n1, which provides a transmission coefficient that satisfies Equation 3.12 is determined iteratively.
7525_C003.indd 90
11/15/07 10:50:47 AM
91
Time-Resolved Terahertz Spectroscopy
Eo
d
Eo
Air
0
Sample*
1
Sample
2
Air
T d
ET
(a)
Air
n
Sample*
n–1
Sample
2
Air
1
(b)
Figure 3.10 Schematic of layers in a dielectric stack with labeling conventions for (a) matrix method and (b) complex impedance method. Here the skin depth of the optical pump is much smaller than the sample thickness, and the sample is divided into photoexcited and non-photoexcited layers.
Alternatively, the transmission coefficient can be defined in terms of the impedances of each layer in the stack by25
1 = z( k )
j = n -1
∏ j =1
Z j +1 + Z Zj + Z
( j) in ( j) in
exp ( - i φ j )
(3.18)
where z(k) is the transmission coefficient for a wave incident on layer n of an nlayered stack as shown in Figure 3.10b, and fj = kj(w)dj. The propagation distance through the jth layer dj is defined as zero for the semi-infinite layers j = 1 and j = n. The impedance of the jth layer is defined as Zj = w/ckj(w), and the input impedance of the jth interface is defined as Z in( j ) =
Z inj -1 - iZ j tan φ j Zj Z j - iZ inj -1 tan φ j
(3.19)
where Zin(0) = Z1. It is worth noting that this procedure for extracting the photoexcited optical constants of a single layer in the dielectric stack assumes that none of the other layers’ optical constants change on photoexcitation. When multiple layers are excited, it is mathematically impossible to determine all of the individual optical constants. In these cases, TRTS still measures the changes in optical density and phase of the complete stack, but extraction of material parameters for each individual layer requires additional information about the system.
7525_C003.indd 91
11/15/07 10:50:50 AM
92
Terahertz Spectroscopy: Principles and Applications
3.2.4.3 Special Treatment at Short Pump-Delay Times When the response of the material is fast compared with the temporal duration of the THz pulse, the data collection and analysis described previously are not adequate. For most samples, this is only important when the pump pulse arrives whereas the THz pulse is propagating through the sample. In these cases, proper analysis requires a full 2D grid of THz difference scans, DETHz(t,t″), along with subsequent deconvolution of the detector response function. DETHz(t,t″) corresponds to pump-on minus pump-off, with t referring to the THz-delay time and t″ marking the arrival of the pump pulse. Figure 3.11 displays such a 2D TRTS data set, where a series of THz difference scans are taken at a variety of pump delay intervals by scanning the detector delay line.22 It is clear from Figure 3.11 that the individual THz difference scans are strongly influenced by the arrival of the pump pulse (shown as arrows). Schmuttenmaer et al. have shown that the data parallel to the 45° axis of this plot (shown with a bold line) consist of THz difference scans that have experienced a constant delay from the pump pulse.9,27 These scans can be obtained by a numerical projection of the original data set. Alternatively, they can be collected directly by fixing the relative time between the detector and the pump delays, either by synchronously scanning the THz detector and pump delay lines together with fixed THz 4
(w)
2
(x)
t´´ (ps)
3
1
(y) (z) 0
1
2
3
4
0
THz Delay (ps) (w) (x) (y) (z)
Figure 3.11 Typical time-resolved THz spectrometer two-dimensional dataset. Contour plot of ∆ETHz (pump-on minus pump-off). The solid lines are negative values and the dashed lines are positive. The bold solid diagonal line represents the arrival of the pump pulse. The pump pulse affects only that part of the THz pulse that comes after it. These are individual scans corresponding to the arrows on the grid; the arrows represent the arrival of the visible pulse. (Figure reprinted with permission from Beard, M.C. et al., J. Appl. Phys., EPAPS, 90, 5915, 2001. Copyright 2000 by the American Institute of Physics.)
7525_C003.indd 92
11/15/07 10:50:53 AM
3
2
2
1
t-t´´(ps)
3
1
0 1
2
3
4
–1
t-t´´(ps)
93
Time-Resolved Terahertz Spectroscopy
0 1
2
3
t(ps)
t(ps)
(a)
(b)
4
–1
Figure 3.12 (a) Contour plot of ∆ETHz (pump-on minus pump-off) as a function of constant reference time. The solid lines correspond to positive ∆ETHz values and the dashed lines correspond to negative values. The 45° component seen in Figure 3.11 has been removed as explained in the text. However, there is a component near pump delay t″ = 0, which curves to the left and appears to come before the pump pulse has arrived. (b) After deconvolution, these features have essentially been removed. (Figure reprinted with permission from Beard, M.C. et al., J. Appl. Phys., EPAPS, 90, 5915, 2001. Copyright 2000 by the American Institute of Physics.)
generator delay, or by scanning the THz generator delay with the pump and THz detector delays fixed. Any of these methods will result in a dataset that consists of THz scans that have experienced a constant delay from the pump pulse. Figure 3.12a displays a data set for GaAs which has been collected by scanning the THz generator delay line.22 This method removes the 45° component in Figure 3.11, but a new component curving to the left at early pump delay times has appeared. This new feature appears to grow in before the arrival of the pump pulse. This apparent superluminal phenomenon arises from the convolution of the detector response function with the true THz waveform. Deconvolution of the detector response function removes this feature, as shown in Figure 3.12b. The detector response must be deconvolved because its finite bandwidth acts as a low-pass filter, broadening the true pulse. To correct for this artifact we deconvolve the detector response from the measured signal using the procedure shown in Figure 3.13.22 Figure 3.13a shows a hypothetical reference pulse (solid line) after passing through the sample, but before propagating through the ZnTe detector crystal. Overlaid is a pulse that has experienced photoexcitation while the THz pulse was in the sample (dashed line), such that only the trailing portion of the pulse is affected by the photoexcitation. The vertical line indicates the moment of photoexcitation. After propagation through the detector, the photoexcited output pulse (Figure 3.13b) has features that appear to differ from the reference pulse before the pump pulse arrives. After numerical deconvolution, the reference and the photoexcited scans (Figure 3.13c) are largely restored to their shapes before passing though the detector, and the features occurring before the arrival of the pump pulse have essentially disappeared. Figure 3.13d shows the photoexcited scans before and after passing through the detector and after deconvolution.
7525_C003.indd 93
11/15/07 10:50:56 AM
94
Terahertz Spectroscopy: Principles and Applications (a) (b)
ZnTe Detector (d)
5
6
(c)
7
THz Propagation (ps)
1 1
2
3
2
3
THz Propagation (ps)
THz Propagation (ps)
Figure 3.13 Illustration of the detector filtering effect on a THz pulse transmitted through a photoexcited medium. In (a), the solid line is the reference scan (no photoexcitation), the dashed line represents the transmitted pulse when there is photoexcitation, and the dotted line represents a decrease in sample transmission due to the photoexcitation pulse. The reference and photoexcited pulses are identical until the moment of photoexcitation, represented by the vertical line. (b) Propagation through the detector (ZnTe) distorts the waveforms. (c) Numerical deconvolution of the detector response removes the effect of propagation and nearly restores the scans to their shape before propagation. The differences between the reference and photoexcited scans are shown in (d) to further illustrate this point. The thin solid line is the difference before propagation, the bold solid line is the difference after propagation and without deconvolution, and the dashed line (hardly distinguishable from the thin solid line) is the difference after deconvolution. (Figure reprinted with permission from Beard, M.C. et al. J. Appl. Phys., EPAPS, 90, 5915, 2001. Copyright 2000 by the American Institute of Physics.)
To perform the detector deconvolution, Beard et al. have used a Fourier transform method that includes optimal filtering.10,28 The electrooptic detection of a THz pulse has been modeled by Bakker et al.29 and is given by DI EO (τ) ∝ r41
l
∫ ∫ dz
0
∞
-∞
dt I p (z ,t - τ) E (z ,t )
(3.20)
with E ( z, t ) =
∫
∞
-∞
dwE ( 0, w ) exp (izkznTe - iwt )
(3.21)
where DIEO (t) is the detected signal, E(z,t) is the propagated THz pulse at a distance z into the detector crystal, Ip(z,t-t) represents the propagating visible pulse (assumed to be Gaussian), t is the temporal delay between the two pulses, kZnTe is the complex propagation vector of the THz pulse in the ZnTe crystal, and r41 is the electrooptic coefficient for ZnTe. Equation 3.20 can be regarded as a simple convolution of the detector response with the THz pulse, given by
7525_C003.indd 94
DI EO ( τ ) ∝
∫
t
-∞
E ( 0, t ) χ d (t - τ ) dt
(3.22)
11/15/07 10:51:01 AM
Time-Resolved Terahertz Spectroscopy
95
with χ d being the response function of the detector. If χ d is known, a Fourier deconvolution can be used to obtain E(0,t), the THz pulse before propagation through the detector. The detector response function, χ d, is most easily generated by numerically propagating a Dirac delta function through the detector using Equations 3.20 and 3.21. The complex propagation vector kZnTe, given in Equation 3.11, can be measured in a separate THz-TDS measurement. The deconvolution procedure requires data collected in the conventional fashion as shown in Figure 3.11, where the pump delay line is fixed while scanning the THz (generator) delay line. Each THz difference scan is then deconvolved from the detector. Finally, the data are numerically projected to obtain deconvolved difference scans with constant pump delay times. This process removes most of the features that result from convolution with the detector, as seen in Figure 3.12b. The frequency-dependent optical parameters can be then be extracted from the deconvolved and numerically projected data as discussed in Section 3.3.4.1. Deconvolution is not required when the response of the material is slow compared with the detector response time. For example, Figure 3.5 is a 2D plot of the response of low-temperature-GaAs collected when scanning the THz generator.22 Photoexcitation at 400 nm produces electrons that immediately (~10 fs) scatter to the low mobility L and X valleys. The far-IR response is then governed by the return of the electrons to the high mobility G valley.9,30–32 As a result, the rise time of the THz absorption is slow and deconvolution is not required. Figure 3.5 shows the collected data without deconvolution, and no artifacts are present. The group velocity mismatch of the pump and probe pulses in the sample can typically be neglected, because they traverse only a few microns of photoexcited material in most samples. The temporal resolution of TRTS is determined by the approximate 200-fs detector response function and any geometrical limitations such as spatial overlap of the pump and probe beams, or noncollinear propagation of the beams.9 3.2.4.4 Treatment of Porous Media That TRTS is a noncontact probe is a great advantage for studying nanomaterials. Making contacts to very small objects is difficult and the contacts themselves can sometimes dominate resistance measurements. When investigating porous nanomaterials such as nanoparticle films or nanowire arrays, where the wavelength of the THz probe radiation (150 µm–1.5 mm) is much larger than the characteristic particle dimensions, it is appropriate to use effective medium theory.33 Effective medium theory is frequently used to calculate the permittivity of a composite material given the permittivity and volume fraction of each of the individual components. However, it can also be used in reverse to calculate the permittivity of one component when the permittivities of the other component and the composite are known.16,34 The latter is often the more useful method, for example when calculating the permittivity of the semiconductor in an air–semiconductor composite where the permittivity of air is known and that of the composite is measured. The Bruggeman effective medium approximation (EMA)35 and MaxwellGarnett theory (MGT),36 both based on the Lorentz-Lorenz (Clausius-Mossotti) equation, are two of the most commonly used effective medium theories. Each
7525_C003.indd 95
11/15/07 10:51:02 AM
96
Terahertz Spectroscopy: Principles and Applications
makes slightly different assumptions, and each has advantages and limitations.33 For example, Hendry et al. have used MGT to compare the measured composite permittivity of a mesoporous TiO2 nanoparticle film with that calculated using the permittivities of bulk TiO2 and air.15 However, singularities in reverse MGT occur for large semiconductor volume fractions and large contrast ratios of the individual component permittivities. Therefore, using reverse MGT to calculate nanostructure permittivities from composite measurements does not give robust and reliable results.16 Conversely, the reverse Bruggeman EMA does not exhibit these singularities. The Bruggeman EMA is given by
e -e em - e f p = 0, + (1 - f ) e m + K e ep + Ke
(3.23)
where f is the particle volume fraction, e is the composite permittivity, em is the matrix permittivity, ep is the particle permittivity, and K is a geometric factor. K is 1 for an array of cylinders with axes collinear with the incident radiation and 2 for spherical particles.34 The semiconductor absorption coefficient and refractive index are calculated from the composite absorption coefficient and refractive index by using the reverse Bruggeman EMA. Solving for the particle permittivity in Equation 3.23, with em equal to unity for air, gives
ep =
e [f (1 + K e ) + (1 - f ) K (e - 1)] . f (1 + K e ) + (1 - f ) (1 - e )
(3.24)
Using this procedure, permittivities of nanomaterials can be calculated and compared with those of bulk materials. Additionally, nanomaterials of different shapes and sizes can be compared with each other to examine the influence of morphology on conductivity without having to make contacts to individual nanostructures.
3.3 TerahertZ Emission Spectroscopy An overview of types of materials studied over the years using THz emission spectroscopy (TES) can be found in previous work.1 Examples include bulk semiconductors, semiconductor heterostructures such as quantum wells and superlattices, superconductors, magnetoresistive manganite thin films, organic molecules, either crystalline or in solution, and relativistic electron beam bunches. More recently, ultrafast demagnetization in thin magnetic films has been characterized with TES,37,38 and THz emission from surface plasmons in a metal grating has been observed.39 In general, a sample is photoexcited and radiates a THz pulse from an induced current or polarization (either electric or magnetic), and the radiated THz waveform is analyzed to uncover the dynamics of the underlying process. TES differs from TRTS and THz-TDS in that a THz probe pulse is not used to interrogate the far-IR optical properties of the sample, either with or without prior photoexcitation, respectively.
7525_C003.indd 96
11/15/07 10:51:04 AM
97
Time-Resolved Terahertz Spectroscopy
A THz pulse is emitted due to a time-dependent polarization (or current) of the sample. In the near-field it is given by
E x (t ) ∝
∂2Px (t ) , ∂t 2
(3.25)
E x (t ) ∝
∂J x (t ) , ∂t
(3.26)
or equivalently,
where Px(t) and Jx(t) are the time-dependent polarization and current, respectively. Furthermore, if the underlying mechanism is optical rectification, a nonresonant, nonlinear process, Jx(t) in Equation 3.26 is given by the “rectification current”
J rect (t ) = 2e o χ( 2)
∂ E (t )E * (t ), ∂t
(3.27)
where c(2) is the second-order nonlinear susceptibility. That is, it is the time derivative of the excitation pulse. Thus by carefully measuring the emitted waveform, it is possible to determine the origin of the signal (i.e., a nonresonant process such as rectification versus a resonant process in which there is a real current). The waveform for a nonresonant process is determined solely by the excitation laser pulse shape and duration. However, in the case of a real current, the time-dependent polarization or current can be extracted from the waveform, assuming it is slower than the duration of the excitation pulse. Similarly, if the magnetization of the sample is time-dependent, it generates a current, and the emitted THz pulse is given by
E y (t ) ∝
∂2M x (t ) , ∂t 2
(3.28)
where Mx(t) is the time-dependent magnetization. Note that the electric field of the emitted pulse is orthogonal to the direction of the changing magnetization. These equations, and Maxwell’s equations themselves for that matter, are independent of any particular timescale. That is, picosecond dynamics lead to THz waveforms, nanosecond dynamics lead to GHz waveforms, and so on. However, such a wide variety of important chemical and physical processes occur on a picosecond timescale that TES is an indispensable technique.
3.3.1 Experimental A typical TES setup is shown schematically in Figure 3.14. A regeneratively amplified titanium–sapphire laser produces an approximate 100-fs laser pulses centered at a wavelength of 800 nm with a repetition rate of 1 kHz. The beam is split into
7525_C003.indd 97
11/15/07 10:51:08 AM
98
Terahertz Spectroscopy: Principles and Applications θy θx
Regeneratively Amplified Ti: Sapphire Laser 1 mJ/pulse, 1 kHz Rep Rate, 100 fs Pulsewidth Variable Time Delay
θz Visible Beam Block
(a)
Nonpolarizing ZnTe Beam Splitter
Sample
Polarizing Beam Splitter λ/4
Vertical Polarizer
Si Photodiodes
Figure 3.14 Experimental schematic for THz emission spectroscopy. “Transmission” mode is indicated. It is also possible to operate in “reflection” mode wherein the excitation beam travels away from the detector, and the THz pulse emitted in the reflected direction is detected. Inset (a) displays a coordinate system (z is the direction of propagation of the excitation laser).
two parts, pump and readout, with about 99.9% of the energy being used to excite the sample after traveling along a variable delay line. A paper or polystyrene visible beam block ensures that any visible power not absorbed by the sample does not reach the detector. The other portion of the visible pulse reflects off a beamsplitter and travels through a vertical polarizer before reflecting off a second non-polarizing beamsplitter. It is used to detect the EM transient via free space electrooptic sampling40 in a 0.5-mm thick <110> ZnTe crystal. The detector is polarization-sensitive, but a wire-grid polarizer that rejects orthogonally polarized THz radiation is placed in front of the detector crystal to ensure maximum fidelity. The sample can be rotated azimuthally about the surface normal, qz, or it can be rotated about the vertical, qy, and/or horizontal axes, qx, if oblique incidence is required (see inset in Figure 3.14 for coordinate system). 3.3.1.1 Far Field versus Near Field The far-field pulse shape is related to the near‑field pulse by a time derivative.41 This relationship can be verified by using ZnTe as both the generator and detector. When using the highly efficient ZnTe generator, the beam waist can be expanded such that the near‑field regime is obtainable. A comparison of the near- and far‑field signals is shown in Figure 3.15. The far field is defined as d >> r 2 / ct0 , where d is the distance of the detector from the sample, r is the transverse radius of the visible pump beam, and t0 is the full width half maximum of the transient. For large bandwidth nearly signal cycle pulses, the pulse length, ct0, is a better metric for the near‑ and far‑field regimes than is the wavelength, λ. Typically, r 2 /ct0 ≈ 1 cm, and it is best to ensure that the far field has
7525_C003.indd 98
11/15/07 10:51:11 AM
99
EΩ(arb. units)
Time-Resolved Terahertz Spectroscopy Near-Field d << r2/(ct0)
1
Sample Detector
0 Far-Field d >> r2/(ct0)
–1 –2
–2
0 THz Delay (ps)
d 2
Figure 3.15 THz generation is produced from ZnTe via optical rectification to illustrate near- versus far-field regimes. The open circles are the first derivatives of the near-field signal, whereas the lines are the measured near-field and far-field signals. The detector configuration is shown to the right. (Figure reprinted with permission from Beard, M.C. et al., J. Phys. Chem. A 106, 878, 2002. Copyright 2002 by the American Chemical Society.)
been achieved by increasing d until the pulse shape no longer changes shape with increasing distance, at which point d is usually about 3 cm or more. In rare cases, the signal can be collected in the near-field regime (that is, when it is possible to position the detector essentially in contact with the sample), which would allow the pulse shape to be measured directly. However, because of the relatively small excitation spot size and because it is often impossible to place the detector close enough to the photoexcited medium to be in the near field, the signal is typically collected in the far‑field regime. 3.3.1.2 Terahertz Focusing Optics Regardless of whether one collects data in the far field or near field, one of the most important considerations is that focusing optics not be used. The detector is placed adjacent to the sample as shown in Figure 3.14. Collecting the data in this manner allows one to obtain the true underlying dynamics, but at the cost of a lower signal-to-noise ratio compared with when THz focusing optics are used. However, one avoids difficulties of astigmatism, Guoy phase shift, and other diffraction‑induced pulse distortions that occur with large bandwidth pulses. The pitfall with using focusing optics is that variations in the THz waveform will be attributed to time-dependent changes in the polarization, when in fact it is nothing more than experimental misalignment. In addition, one must be absolutely certain that there are not other systematic artifacts. This is especially true when rotating the laser polarization, or if the sample is inside a cryostat. For extremely weak signals, it is imperative that every possible source of generation is ruled out; we have measured very weak THz generation from neutral density filters for example.
3.3.2 Data Analysis After the data are collected, useful information must be extracted. The data analysis begins with observing the dependence of the THz emission on sample rotation/
7525_C003.indd 99
11/15/07 10:51:14 AM
100
Terahertz Spectroscopy: Principles and Applications
orientation and excitation polarization. In addition, one can analyze the emitted waveforms for additional information. 3.3.2.1 Sample Orientation The sample may be rotated azimuthally (about the surface normal, qz) or obliquely (about the axes perpendicular to the surface normal, qy or qx). For example, several well-known generation mechanisms in semiconductors rely on a current surge along the surface normal. These are the surface depletion field and the photo-Dember effect. The surface depletion field occurs when the Fermi level is pinned to surface states or trap states thereby causing “band bending” at the surface. On photoexcitation, electrons are accelerated toward or way from the surface, depending on the sign of the field.42 The photo-Dember effect occurs even when band bending is not present because electrons and holes have different mobility. On photoexcitation, the carriers diffuse, but at different rates. Thus a net current normal to the surface results.43 If the sample is at or near normal incidence, THz pulses from either of these mechanisms will be very small. The only reason they are measurable at all is because either the sample is not perfectly normal to the excitation beam and detector, or more likely, because a focusing lens is being used.44 So, if either of these mechanisms is responsible, it will become apparent by a strong dependence on rotation of the sample about the x or y axis, but not on azimuthal rotation. If the current is along a well defined direction in the surface plane, then the THz emission will decrease as the sample is rotated about the axis perpendicular to the direction of the current surge, but not if it is rotated about the axis in the direction of the current surge (neglecting any effects due to differences in reflectivity as a function of angle). It will also depend (co)sinusoidally on the azimuthal angle. 3.3.2.2 Excitation Polarization Another important consideration is the dependence of the waveform on the polarization of the excitation beam (linear, either vertical or horizontal, or some of both, elliptical, or circular). For example, the THz emission in the x and y directions (lab-fixed) as a function of rotation of a linearly polarized excitation beam for a system of partially oriented dye molecules is shown in Figure 3.16. Conversely, the emission from a magnetic thin film is independent of excitation laser polarization since the fundamental mechanism is ultrafast thermal heating of the electrons: it only depends on sample orientation as seen in Figure 3.17.37 Similarly, the emission from a photoconductive switch is independent of the polarization direction (or ellipticity) of the excitation laser because the fundamental mechanism is simply generation of conduction band electrons, which are then accelerated by the applied bias voltage. Thus the underlying mechanism of the THz emission dictates whether it depends on the excitation laser polarization or not. 3.3.2.3 Emitted Waveform The shape of the emitted pulse reveals additional information about the underlying process. For example, in GaAs or other semiconductors, one can produce THz
7525_C003.indd 100
11/15/07 10:51:15 AM
101
Time-Resolved Terahertz Spectroscopy 2e-5 EΩ(arb. units)
2e-5 1e-5 8e-6 4e-6 0 –4e-6 –8e-6
0
50
100
150
200
Polarization Angle (ζ) (b)
Figure 3.16 Dependence of the generated signal amplitude as a function of visible polarization angle, ζ, detecting the x component (filled circles) and y component (open circles) of the generated pulse amplitude. The static electric field is in the x direction. (Figure reprinted with permission from Beard, M.C. et al., J. Phys. Chem. A 106, 878, 2002. Copyright 2002 by the American Chemical Society.)
THz Amplitude (arb. units)
radiation (at normal incidence and without a bias voltage) from either optical rectification, if the photon energy is below the bandgap, or a shift current if the photon energy is above the bandgap.45 By analyzing the waveforms, it is possible to distinguish these two mechanisms, even though the amplitude for THz emission for both mechanisms depends on excitation polarization in the same fashion. As will be seen in Section 3.3.3.2, the two waveforms are related through a time derivative. With sample orientation and excitation polarization information in hand, the analysis of the waveform is guided by the putative mechanism of basis for THz pulse generation. That is, if one suspects that a current surge is the mechanism, either increasing or decreasing, he will then invoke a model that treats time-varying
1e-5 5e-6
M
0
y
–5e-6 –1e-5
0
90
180
270
360
z
x
Sample Rotation (Degrees)
Figure 3.17 (Left) THz emission from demagnetization as a function of sample orientation as it is rotated about z axis. (Right) Relevant coordinate system. A change in magnetization along the y axis produces a THz pulse polarized along the x axis. The THz emission is independent of excitation laser polarization.
7525_C003.indd 101
11/15/07 10:51:18 AM
102
THz Amplitude (arb. units)
Terahertz Spectroscopy: Principles and Applications 1e-6 8e-7 6e-7 4e-7 2e-7 0
–2e-7
0
2
4 Time (ps)
6
8
(a)
0
1
2
3
4
5
6
7
8
6
7
8
Time (ps) (b)
0
1
2
3
4
5
Time (ps) (c)
Figure 3.18 Experimentally measured THz emission shown with solid line (a). The sample is a 40-nm thick in-plane magnetized Ni film. (b) The “basis set” of Gaussian functions whose amplitudes were then arbitrarily varied in a nonlinear least-squares loop to produce the change in magnetization shown with the thick line (c). One of the Gaussians was randomly chosen and shown with a thick line (b). The THz emission shown with the dashed line (a) is calculated by taking its first derivative and convoluting with the detector response function.
currents. Similarly, if a change in polarization or magnetization is suspected, then it is analyzed as such. It is also possible to extract the underlying change in current, polarization, or magnetization without assuming any model. For example, the solid line in Figure 3.18a is the emitted near-field THz pulse from a 40-nm thick magnetic Ni thin film. One generates (numerically) a series of Gaussians in the time domain as shown in Figure 3.18b, then uses a least-squares loop to vary their amplitudes, and convolute the underlying change in current, polarization, or magnetization with the
7525_C003.indd 102
11/15/07 10:51:27 AM
Time-Resolved Terahertz Spectroscopy
103
detector response until agreement with the data is achieved. Figure 3.18c shows the underlying change in magnetization before convolution with the detector response function and before taking its first derivative. The dashed line in Figure 3.18a is the calculated THz pulse based on the time-dependent magnetization shown in Figure 3.18c (i.e., taking the first derivative of the magnetization shown in Figure 3.18c), and convoluting it with the detector response function. It might also be necessary to investigate both the first and second derivative of the underlying change if the source is not known.
3.3.3 Specific Examples In all cases, the goal is to determine Jx(t), Px(t), or Mx(t) from the measured THz waveform. Typically, a model is chosen to describe the underlying process, which is then convoluted it with an instrument response function. The parameters of the model are then varied using a nonlinear least squares fitting program until agreement between the calculated and measured waveforms is achieved, at which point one has obtained information about the underlying generation mechanism. 3.3.3.1 Photoconductive Switches Some of the earliest TES studies were to understand the mechanism behind THz generation from a photoconductive switch, the first type of source used for THzTDS. This required understanding the current surge because of the acceleration of photoexcited electrons by an applied bias field. That is, Jx(t) in Equation 3.26 is given by:
J x (t ) = -enf (t )v (t ),
(3.29)
where e is the magnitude of the electron charge, nf (t) is the time-dependent density of free (i.e., photogenerated) electrons, and v(t) is their time-dependent mean velocity. The time-dependent carrier density is related to the excitation pulsewidth as a generation mechanism, and any scattering, damping, or trapping that may be present. The time-dependent velocity depends on the effective mass of the electrons which depends on their location in the (nonparabolic) conduction band, as well as the local field, which results from the applied field as well as any screening effects. These effects can be treated either analytically,46–48 or numerically via a Monte Carlo approach.49 3.3.3.2 Shift Currents and Optical Rectification Although biased semiconductor photoconductive switches produce THz radiation because of a current surge, there exist other mechanisms as well. Perhaps most well known is optical rectification (the mechanism for THz generation in ZnTe emitters, which are popular sources of THz radiation for THz-TDS and TRTS experiments). Shift current and injection current are second-order mechanisms that do not require a bias field and can produce a pulse when the sample surface is normal to the direction of excitation.
7525_C003.indd 103
11/15/07 10:51:29 AM
104
Terahertz Spectroscopy: Principles and Applications
Sipe and coworkers have developed a detailed mechanistic treatment of secondorder responses in semiconductors by deriving an expression for the second-order susceptibility, χ(2) which is valid for below, above, and at bandgap conditions.45 The most salient results of their work are summarized below. For semiconductors, the second-order susceptibility may be written in the following form (in the frequency domain): χ( 2) (- W ;w , -w + W) = χ( 2)′ (- W; w , - w + W) +
σ ( 2) (- W; w , -w + W) iW
η( 2) (- W; w , -w + W) + (- i W) 2
(3.30)
The first term describes optical rectification, the second shift current, whereas the last term accounts for injection currents. W is a THz frequency, and W is an optical frequency. For zincblende materials such as GaAs, the injection current term vanishes because of symmetry. The current density has contributions due to rectification and shift currents:
J (t ) = J rect (t ) + J shift (t )
(3.31)
These current densities can be related to the applied electric field:
J rect (t ) = 2e o χ( 2)
∂ E (t )E * (t ) ∂t
J shift (t ) = 2e o σ ( 2)E (t )E * (t )
(3.32)
(3.33)
when detecting in the far field, where the signal appears as its first derivative with respect to time,41 the THz waveform should have the following profile with respect to the optical pulse:
rect (t ) = 2e χ ( 2 ) E THz o
∂2 E (t )E * (t ) ∂t 2
(3.34)
shift (t ) = 2e σ ( 2 ) ETHz o
∂ E (t ) E * (t ) ∂t
(3.35)
3.3.3.2.1 Laser Polarization Dependence of Second-Order Response The THz pulse generated from optical rectification or shift currents depends on the polarization state of the laser (linear, elliptical, circular) and the orientation of the sample. We employ the Jones matrix formalism to account for the various optics
7525_C003.indd 104
11/15/07 10:51:33 AM
105
Time-Resolved Terahertz Spectroscopy
and sample orientation.50 In this formalism, the elements of the vectors and matrices below are complex quantities. The initial polarization of the optical beam is written as
E x ,opt Elab = E y,opt Ez,opt
(3.36)
where x, y, and z are lab fixed coordinates. The z direction is the direction of propagation, and we can arbitrarily choose the x direction as horizontal and y vertical. Thus a horizontally, linearly polarized beam emerging from the laser is represented as
Elab
1 = 0 . 0
(3.37)
When the beam passes through a waveplate, the polarization state of the emerging beam is expressed as:
E x ′,opt E x ,opt Elab ′ = E y′, opt = W E y, opt = WElab E E z′, opt z, opt
(3.38)
where W is the product of the matrices:
W = R (-q) W0 R (q)
(3.39)
with:
e - i G / 2 W0 = e i φ 0 0
0 e - iG / 2 0
0 0 1
cos q R(q) = - sin q 0
sin q cos q 0
0 0. 1
(3.40)
and
7525_C003.indd 105
(3.41)
11/15/07 10:51:39 AM
106
Terahertz Spectroscopy: Principles and Applications
W0 is the matrix describing the phase retardation placed on the optical beam with Γ equal to p for a half-wave plate or p/2 for a quarter-wave plate. R(θ) is a rotation matrix that transforms the incident optical beam onto the fast and slow axes of the wave plate, and θ is the angle of the optical beam with respect to the fast axes. The emerging beam is then transformed back into lab coordinates using R(-θ) and carries the polarization induced by the waveplate. The optical field is then projected onto the crystallographic axis of the sample:
Extal
Ei = Ej = T Ek
Ex′ ′ E y ′ = TElab Ez ′
(3.42)
where T is the transformation matrix projecting the electric field in lab coordinates onto the i, j, k crystallographic axes of the GaAs <111> sample: T =
2 3 1
3
1
6 1 6
2
-
1 3 1 3 1
0
1 2
(3.43)
For zincblende crystals such as GaAs, the induced polarization, or “current”, in the ith direction is proportional to the product of the optical fields polarized along the jth and kth direction: Pi ∝ E j E k* , where i, j, and k are mutually orthogonal Cartesian coordinates, and E* is the complex conjugate of E.51,52
0 P = Ek 0
0 0
Ei
Ej 0 0
E i* 0 * E j = Ek * 0 Ek
0 0 Ei
Ej * 0 Extal 0
(3.44)
This time-dependent polarization leads to the observed THz emission, which is transformed back into lab coordinates:
ETHz
E x ,THz = E y ,THz = T -1P E z ,THz
(3.45)
where T–1 is the inverse of the transformation matrix T. The calculated signal is obtained by taking the real part of ETHz in Equation 3.45.
7525_C003.indd 106
11/15/07 10:51:43 AM
107
Time-Resolved Terahertz Spectroscopy
Putting this together, we have:
ETHz = T-1 P TR ( - q)W 0 R(q) Elab .
(3.46)
On the other hand, if we were to rotate the sample instead of the waveplate, it would be
ETHz = R( - q) T -1 P TR (q)W 0 Elab
(3.47)
(with the optical axis of the waveplate along the polarization of the optical beam), or perhaps more simply, to eliminate the waveplate:
ETHz = R ( - q) T -1 P TR (q) Elab .
(3.48)
In summary, the Jones matrix formalism50 is a well-known and efficient way to describe and understand the effects of essentially any optical element as well as the samples themselves. 3.3.3.3 Intramolecular Charge Transfer in Orienting Field It is possible to generate THz emission from a sample of oriented dye molecules that undergo intramolecular charge transfer on photoexcitation. This provides a way to understand this process without relying on secondary effects such as a change in absorption or fluorescence properties. The signal is simply because of the change in polarization of the sample. It is possible to orient the molecules several ways. If a single crystal can be grown, and if it has the appropriate symmetry, then that will lead to a net orientation. Also, in some cases it is possible to make monolayers or multilayers of oriented molecules. In the work discussed here, however, an applied electric field is used to partially orient the molecules. Any TES experiment can be described as a nonlinear process. However, it is sometimes useful to think more intuitively about the underlying physical process. For the purpose of illustration, we will compare and contrast TES from oriented dye molecules in terms of the considerations of intramolecular charge transfer in partially oriented molecules versus a description based on the third-order nonlinear susceptibility. In both cases, the x axis is defined as the direction of the applied electric field. The angle of a molecular ground state dipole moment relative to the x axis is denoted q. The angle of the linearly polarized photoexcitation beam relative to the x axis is denoted z. The angle of the polarization axis of the THz detector relative to the x axis is denoted f. 3.3.3.3.1 Intuitive Description The interaction of the static electric field with a dipolar molecule in solution results in a fractional orientation of the molecules along the field direction, which provides the underlying physical basis for this method. This fractional orientation can be calculated by considering the interaction energy of a dipole with an applied field, μgE 0 in comparison to kBT, where kB is Boltzmann’s constant and T is the temperature
7525_C003.indd 107
11/15/07 10:51:46 AM
108
Terahertz Spectroscopy: Principles and Applications
in Kelvin. It is expressed as a function of angle, θ, between the applied field and molecular dipole moment by53,54
f (q) =
1 e -V / k BT ≈ -V / k BT ∫ e d q 2p 2p 0
mE 0 cos q 1+ , k T B
(3.49)
where the interaction potential, V, is given by V = –mE 0cosq. Terms resulting from polarizability anisotropy have been neglected. Given the inherent azimuthal symmetry, we work in polar coordinates. Thus interaction with the static field results in a linear combination of an isotropic distribution and one that varies as cosθ. The visible pulse introduces a cos2(θ – ζ) distribution of excited molecules because of projection of the transition dipole moment onto its polarization. An additional factor of cos(θ – φ) results from a projection of the emitted polarization onto an axis at angle φ. Thus the emitted amplitude at a given polarization angle φ varies as a function of visible polarization angle, ζ, as
E φW (z) ∝
∫
2p
0
(
)
cos(q) cos2 (q - z) cos (q - φ) d q = A z, φ ,
(3.50)
where the integral evaluates to
A(z, φ) =
p [cos φ (3 cos2 z + sin 2 z) + 2 sin φ cos z sin z]. 4
(3.51)
3.3.3.3.2 Third-Order Nonlinear Susceptibility Description It is also possible to treat this process in terms of a third-order nonlinear susceptibility:55
3) w w 0 E iW ∝ χ(ijkl E j Ek El ,
(3.52)
where E W is the THz electric field (which arises from the time-dependent, third-order polarization, Pi(3)), E w is the optical electric field, E 0 is the static electric field, and i, j, k, and l are one of the( 3x, y, z Cartesian coordinates. The third-order nonlinear ) susceptibility is denoted χijkl . As defined previously, the applied field (E 0) is in the x direction (therefore, l = x). Because z is the direction of propagation, i, j, and k must be x or y. For isotropic media there are only three independent tensor elements and they are related by52
3) = χ ( 3) + χ ( 3) + χ ( 3) . χ(xxxx xyyx yxyx yyxx
(3.53)
3) = χ ( 3) = χ ( 3) Also, because Klienman symmetry52 holds in this case, χ(xyyx yyxx yxyx ( 3 ) ( 3 ) and χ xxxx = 3χ xyyx . From these relationships, we can determine the amplitude and
7525_C003.indd 108
11/15/07 10:51:54 AM
109
Time-Resolved Terahertz Spectroscopy
3) . direction of the induced third‑order polarization, P(3), in terms of χ(xyyx The x and y components of P(3) are
3 ) E w E - w E 0 + χ ( 3 ) E w E - w E 0 = χ ( 3 ) I E 0 [3 cos 2 (z ) + sin 2 (z)], Px( 3) (z) = χ(xxx x x x xyyx y y x xyyx w x
(3.54)
and 3 ) E w E - w E 0 + χ ( 3 ) E w E - w E 0 = χ ( 3 ) I E 0 [2 cos(z )sin (z)] Py( 3) (z) = χ(yyxx y x x yxyx x y x xyyx w x
(3.55)
where I wjk is the intensity of the visible pulse with polarization angle ζ relative to the x-direction. The visible polarization vector, eˆ jk , is given by eˆ jk = eˆx cos z + eˆy sin z. The emitted polarization is at an angle φ with respect to the static field and is obtained from the x and y components P (φ3)= Px( 3) xˆ + Py( 3) yˆ,
(3.56)
where φ = arctan[2 cos(z)sin(z)/(3 cos 2 (z) + sin 2 (z))]. It can easily be verified that Equations 3.54 through 3.56 are equivalent to the angular dependence of Equation 3.51, and the two formalisms are complementary. The x and y components of the emitted field are shown in Figure 3.16 and compared with Equations 3.54 and 3.55 (shown with solid lines). 3.3.3.3.3 Propagation Effects and Solvent Response If propagation effects of the fields through the solvent can be neglected, then the emitted amplitude in the near-field regime is equal to the second derivative of the time-dependent polarization (see Equation 3.25). However, nonnegligible propagation effects such as group velocity mismatch between the visible and generated THz pulses, absorption of the visible pulse by the solution, and dispersion of the generated pulse by the solvent must be accounted for to correctly obtain the charge transfer dynamics. We do so by numerically solving Maxwell’s equations in the time domain56 coupled with the phenomenologic model below for the time-dependent polarization. We then perform a nonlinear least-squares fit of the model to the data to obtain the charge transfer dynamics. It should be noted that an alternative approach is described in Section 3.3.4 and in previous studies.57 Consider a delta function excitation pulse of a single dye molecule at z = 0 and t′ = 0. The pulse induces an electron transfer with rate kET, and subsequent back electron transfer with rate kBET, and the change in polarization is given by Dp (t ) =
7525_C003.indd 109
k ET [exp(- k ET t ] - exp(- k BET t )] D ′m, ( k BET - k ET )
(3.57)
11/15/07 10:52:01 AM
110
Terahertz Spectroscopy: Principles and Applications
where ∆′µ is the change in dipole moment along the ground state dipole. We average the contributions from individual molecules over an anisotropic distribution that is created by the visible and static fields. Because reorientation of the excited molecules occurs on a longer timescale than these measurements, the orientational average is given by D ′m = m ′e
∫
2p 0
f (q) cos 2 (q - z) cos (q - φ ) dq
E0 = A (zz, φ ) (m ′e - m g ) m g , 8kBT
(3.58)
where µg is the ground state dipole moment and m e′ is the projection of the excited state dipole moment along the ground state dipole moment. Thus, the change in polarization is obtained by replacing D′m with 〈D′m〉 in Equation 3.57. The solvent molecules also affect the measured change in polarization, so we must account for their reaction field. The electrostatic potential of a dipole in solution is modified from its value in vacuum by the reaction potential of the polarized surrounding dielectric medium. On photoexcitation, the electrostatic potential changes abruptly and therefore a repolarization of the solvent occurs. If the change in dipole is fast compared with the solvent motions, then the measured change in polarization will reflect this solvent repolarization. We describe the solvent response as an impulse response function to a delta function change in the solute charge configuration. We treat the solvent response as a single exponential, and the combined solvent–solute polarization ps response to an impulse excitation pulse is given by
ps (t ) =
t
∫ dt ′ Dp (t ′) Φ (t - t ′),
(3.59)
0
where Φ(t) = exp(-kst) represents the response of the solvent with rate constant ks. If ks << kET the rise of the signal will be governed by the polarization of the solvent. The FDTD method56 is used to numerically solve Maxwell’s equations with these constraints. The advantage of using the FDTD method is that the slowly varying envelope approximation and rotating wave approximation are not assumed. Although these approximations are valid for the optical pulse, they are not applicable for the generated EM pulse. Furthermore, the FDTD method completely accounts for the generation term and the dispersive term, and group velocity mismatch is automatically included in the simulation. The FDTD calculation provides the generated field in the near‑field regime, and a near-field to far-field transformation is performed by taking the first derivative of the calculated field. The ZnTe detector further distorts the measured signal, and a numerical propagation through the detector is also included in the simulations.9,29 A nonlinear least-squares fit is performed to extract the best fit values of the forward and back electron transfer rates. The results of the fits for Betaine-30 (Reichardt’s dye) in chloroform and DMANS in toluene are shown in Figure 3.19 and the rate constants are provided in Table 3.1.
7525_C003.indd 110
11/15/07 10:52:04 AM
111
Time-Resolved Terahertz Spectroscopy
EΩ(t) (arb. units)
2 DMANS
1 0
Betaine-30
–1 –2 1
2
3 Time (ps)
4
5
DMANS
P(t)
1
Betaine-30 0 0
2
4
6
8
Time (ps)
Figure 3.19 Results of the nonlinear least-squares fit of the charge transfer model (including solvent repolarization) for Betaine-30 in chloroform and DMANS in toluene. The data are shown with solid lines, and the results of the fit with dashed lines. The lower panel displays the underlying time-dependent polarization (Figure reprinted with permission from Beard, M.C. et al., J. Phys. Chem. A 106, 878, 2002. Copyright 2002 by the American Chemical Society.)
Table 3.1 Optimized Parameters Resulting from Nonlinear Least-Squares Fits for Betaine-30 in Chloroform and DMANS in Toluene ∆w (fs)
ks
τs (fs)
(ps ) -1
kET
kBET
(ps )
(ps )
-1
τBET (ps)
-1
Betaine-30
150*
2.86
350
>100*
0.53
1.9
DMANS
150*
1.37
730
>100*
<0.01*
>100*
Note: The corresponding time constants are included for convenience. The Gaussian width is given by ∆w. The asterisk denotes that the values were held fixed during the fit.
7525_C003.indd 111
11/15/07 10:52:06 AM
112
Terahertz Spectroscopy: Principles and Applications
3.3.3.4 Demagnetization Dynamics Finally, it has been shown recently that a sample with magnetization that changes on a picosecond to subpicosecond timescale (as achieved by heating a magnetic thin film with an ultrashort, ~100-fs, laser pulse) will emit THz radiation.37,38 Although initially surprising, it is completely understood through Maxwell’s equations (see Equation 3.28). This implies that the measurement of transient electric field emitted by the sample is related to the second time derivative of the magnetization. Figure 3.20a shows the THz emission from a 40-nm thick, in-plane magnetized Ni film on heating with an ultrafast laser pulse (~100-fs duration, 800-nm wavelength). The THz emission was calculated from a model of the temporal variation of the magnetization (Figure 3.20b) similar to the one previously used in optical pump–probe experiments of Kerr rotation in the same type of sample.58
DM (t ) = {-Θ (t )[k1 (1 - exp ( -t / τth )) exp ( -t / τ ep ) + k2 (1 - exp)( -t / τ ep ))]} ⊗ G (t )
(3.60)
where t is time, ∆M(t) is the time-dependent change in magnetization, Θ(t) is the Heaviside step function centered at t = 0, k1 and k2 are constants depicting the relative
THz Amplitude or Magnetization (arb. units)
1.0
0.5 (a) 0.0
–0.5 (b) –1.0
0
2
4
6
8
Time (ps)
Figure 3.20 The solid line (a) is the near-field THz pulse generated upon ultrafast laser heating of 40-nm thick in-plane magnetized Ni film (in “transmission” mode). (b) The timedependent magnetization as described by Equation 3.60. The dashed line in part (a) is the calculated emission obtained by convoluting the first derivative of the time-dependent magnetization of part (b) with the ZnTe <110> detector response function.
7525_C003.indd 112
11/15/07 10:52:09 AM
113
Time-Resolved Terahertz Spectroscopy
amount of transient response versus long-term values. In the present context, tth and tep may be viewed as phenomenologic constants describing the electron thermalization time and electron–phonon coupling time.58–60 ⊗G(t) represents convolution with a Gaussian instrument response function. The best fit of the second derivative of the magnetization after convolution with the detector response function is plotted as the dashed line in Figure 3.20a. Here we find that tth = 0.37 (0.01) ps, tep = 1.30 (0.04) ps, k1/k2 = 2.0 (held fixed), and the Gaussian instrument response function full width at half maximum is 640. (6.) fs.
3.3.4 General Formalism Recently, Wynne and Carey have developed an integrated description of THz generation from optical rectification, charge transfer, and current surge.61 Each of these three processes is described using an analytical formula in the frequency domain followed by a numerical Fourier transform into the time domain. They account for absorption and dispersion in the detector crystal, as well as the effect of propagation into the far field. Although their treatment avoids explicit FDTD calculations, it cannot describe a situation wherein the response of a sample changes on a timescale fast compared to the inverse of the THz spectral bandwidth. However, there are many scenarios where it is perfectly valid. They provide a recipe. First the THz signal in the near field is calculated and then converted to the far field.
f eikz ( n - nVIS ) - 1 ikzn VIS E THz, NF ( z, w ) = e 2 n nVIS - n E THz ( z, w ) = -iw E THz, NF ( z, w ).
(3.61) (3.62)
In the time domain, the far-field signal is simply the time derivative of the near-field signal,41 which in the frequency domain corresponds to multiplying it by –iw. Here z is the propagation distance, w is the THz frequency, ñ is the complex-valued refractive index of the sample, nVIS is the group refractive index of the material at the excitation wavelength, determined through vgroup = c/nVIS, where c is the speed of light in vacuum, and k is the free-space wavevector of the THz field, k = w/c. Response functions, f(w), are provided for four different scenarios: optical rectification, direct charge transfer, indirect charge transfer, and the current surge model. Optical rectification:
f (w ) = χ( 2) (w ; W, W - w ) Ipump (w ),
(3.63)
where χ(2) is the second-order nonlinear response of the medium, and W represents the range of frequencies contained in the ultrashort pump pulse. Note: Ipump (w ) is the Fourier transform of the intensity envelope of the excitation pulse rather than its spectrum.
7525_C003.indd 113
11/15/07 10:52:13 AM
114
Terahertz Spectroscopy: Principles and Applications
Direct charge transfer: 3e (w ) N Dm f (w ) = I (w ) 2e (w ) + 1 e 0 ( g - i w ) pump
(3.64)
where e (w ) is the continuum dielectric of the sample, N is the number density of photoexcited molecules, ∆m is the change in molecular dipole moment on photoexcitation, e0 is the permittivity of free space. In the case of direct charge transfer, g is the rate of decay back to the ground state with the original dipole moment. Indirect charge transfer: f (w ) =
3e (w ) N Dm 1 1 I pump (w ). 2 e (w ) + 1 e 0 G - iw g - iw
(3.65)
In the case of indirect charge transfer, g is the rate of decay back to an intermediate state, and Γ is the rate of decay back to the ground state with the original dipole moment. Current surge model:
3e (w ) 1 -e 2Enf 1 1 1 I f (w ) = (w ) 2e (w ) + 1 e 0 g s m* - i w G - i w g s - i w pump
(3.66)
where E is a DC external electric field which accelerates the electrons, gs is the momentum relaxation rate, m* is the carrier effective mass, nf is the carrier density, and Γ is the carrier recombination rate (it is assumed that Γ << gs). Note that all these response functions are of the form f (w ) = r (w )Ipump (w ),where r (w ) is a property of the medium in question. The process of electrooptic sampling affects the measured signal, but in a well understood manner.29,62,63 Wynne and Carey account for it and provide an expression for the measured signal:
∫
DI EOS ( τ ) ∝ dw e - iwτ Ipump (w ) Igate (w )[iw ]z gen (w ) r (w )z det (w ),
where
eikL1 ,( n - nVIS ) - 1 , z gen (w ) = 2 n ( nVIS - n )
(3.67)
(3.68)
and
7525_C003.indd 114
e ikL2 ,( n - nVIS ) - 1 z det (w ) = . ik (n - nVIS )
(3.69)
11/15/07 10:52:20 AM
Time-Resolved Terahertz Spectroscopy
115
3.4 Conclusions TRTS and TES can provide information not obtainable from THz-TDS studies (and certainly not from conventional far-IR studies). Both of these methods are sensitive to subpicosecond dynamics manifested in the far-IR region of the spectrum. TRTS is an excellent way to probe the evolution of a material’s complex-valued, time-dependent, far-IR spectrum as a function of time after a perturbation such as a photoexcitation pulse. Section 3.2 describes many considerations that must be taken into account when performing these experiments. TES is complementary in the sense that a full spectrum as a function of time is not obtained. However, that the signal is generated by the sample directly, rather than requiring a THz probe pulse has distinct advantages in some cases. It is evident from Sections 3.3.2 through 3.3.4 that there are many complementary ways of extracting information from a TES experiment.
References 1. Schmuttenmaer, C.A., Exploring dynamics in the far-infrared with terahertz spectroscopy, Chem. Rev., 104, 1759, (2004). 2. Schall, M. and Jepsen, P.U., Photoexcited GaAs surfaces studied by transient terahertz time- domain spectroscopy, Opt. Lett., 25, 13, 2000. 3. Ralph, S.E., et al., Subpicosecond photoconductivity of In0.53Ga0.47As: Intervalley scattering rates observed via THz spectroscopy, Phys. Rev. B, 54, 5568, 1996. 4. Flanders, B.N., Arnett, D.C., and Scherer, N.F., Optical pump-terahertz probe spectroscopy utilizing a cavity-dumped oscillator-driven terahertz spectrometer, IEEE J. Sel. Top. Quantum Electron., 4, 353, 1998. 5. Prabhu, S.S., et al., Carrier dynamics of low-temperature-grown GaAs observed via THz spectroscopy, Appl. Phys. Lett., 70, 2419, 1997. 6. Groeneveld, R.H.M. and Grischkowsky, D., Picosecond time-resolved far-infrared experiments on carriers and excitons in GaAs-AlGaAs multiple-quantum wells, J. Opt. Soc. Am. B-Opt. Phys., 11, 2502, 1994. 7. Saeta, P.N., et al., Intervalley scattering in GaAs and InP probed by pulsed far- infrared transmission spectroscopy, Appl. Phys. Lett., 60, 1477, 1992. 8. Greene, B.I., et al., Picosecond pump and probe spectroscopy utilizing freely propagating terahertz radiation, Opt. Lett., 16, 48, 1991. 9. Beard, M.C., Turner, G.M., and Schmuttenmaer, C.A., Transient photoconductivity in GaAs as measured by time-resolved terahertz spectroscopy, Phys. Rev. B, 62, 15764, 2000. 10. Beard, M.C., Turner, G.M., and Schmuttenmaer, C.A., Subpicosecond carrier dynamics in low-temperature grown GaAs as measured by time-resolved terahertz spectroscopy, J. Appl. Phys., 90, 5915, 2001. 11. Beard, M.C., et al., Electronic coupling in InP nanoparticle arrays, Nano Lett., 3, 1695, 2003. 12. Beard, M.C., Turner, G.M., and Schmuttenmaer, C.A., Size-dependent photoconductivity in CdSe nanoparticles as measured by time-resolved terahertz spectroscopy, Nano Lett., 2, 983, 2002. 13. Hendry, E., et al., Direct observation of electron-to-hole energy transfer in CdSe quantum dots, Phys. Rev. Lett., 96, 057408, 2006. 14. Turner, G.M., Beard, M.C., and Schmuttenmaer, C.A., Carrier localization and cooling in dye-sensitized nanocrystalline titanium dioxide, J. Phys. Chem. B, 106, 11716, 2002.
7525_C003.indd 115
11/15/07 10:52:21 AM
116
Terahertz Spectroscopy: Principles and Applications
15. Hendry, E., et al., Local field effects on electron transport in nanostructured TiO2 revealed by terahertz spectroscopy, Nano Lett., 6, 755, 2006. 16. Baxter, J.B. and Schmuttenmaer, C.A., Conductivity of ZnO nanowires, nanoparticles, and thin films using time-resolved terahertz spectroscopy, J. Phys. Chem. B, 110, 25229, 200). 17. Hendry, E., Charge dynamics in novel semiconductors. Amsterdam: University of Amsterdam, 2005. 18. Perfetti, L., et al., Time-resolved THz spectroscopy: ultrafast charge carrier dynamics in low-dimensional solids, Abs. Ultrafast Phenomena, 2006. 19. Hendry, E., et al., Ultrafast charge generation in a semiconducting polymer studied with THz emission spectroscopy, Phys. Rev. B, 70, 033202, 2004. 20. Hendry, E., et al., Efficiency of exciton and charge carrier photogeneration in a semiconducting polymer, Phys. Rev. Lett., 92, 2004. 21. Hendry, E., et al., Interchain effects in the ultrafast photophysics of a semiconducting polymer: THz time-domain spectroscopy of thin films and isolated chains in solution, Phys. Rev. B, 71, 2005. 22. Beard, M.C., Turner, G.M., and Schmuttenmaer, C.A., Supplementary information for: Sub-picosecond carrier dynamics in low-temperature grown GaAs as measured by time-resolved THz spectroscopy, J. Appl. Phys. EPAPS, 90, E, 2001. 23. Knoesel, E., et al., Charge transport and carrier dynamics in liquids probed by THz time-domain spectroscopy, Phys. Rev. Lett., 86, 340, 200). 24. Beard, M.C. and Schmuttenmaer, C.A., Using the finite-difference time-domain pulse propagation method to simulate time-resolved THz experiments, J. Chem. Phys., 114, 2903, 2001. 25. Brekhovskikh, L.M., Waves in layered media. London: Academic Press, Inc., 1960. 26. Fowles, G.R., Introduction to modern optics. New York: Dover, 1989. 27. Kindt, J.T. and Schmuttenmaer, C.A., Theory for determination of the low-frequency time-dependent response function in liquids using time-resolved terahertz pulse spectroscopy, J. Chem. Phys., 110, 8589, 1999. 28. Press, W.H., et al., Numerical recipes in Fortran, 2nd ed., New York: Cambridge University Press, 1986. 29. Bakker, H.J., et al., Distortion of terahertz pulses in electro-optic sampling, J. Opt. Soc. Am. B-Opt. Phys., 15, 1795, 1998. 30. Bailey, D.W., Stanton, C.J., and Hess, K., Numerical-studies of femtosecond carrier dynamics in GaAs, Phys. Rev. B, 42, 3423, 1990. 31. Stanton, C.J. and Bailey, D.W., Rate-equations for the study of femtosecond intervalley scattering in compound semiconductors, Phys. Rev. B, 45, 8369, 1992. 32. Nuss, M.C., Auston, D.H., and Capasso, F., Direct subpicosecond measurement of carrier mobility of photoexcited electrons in gallium-arsenide, Phys. Rev. Lett., 58, 2355, 1987. 33. Choy, T.C., Effective medium theory: principles and applications. Oxford: Clarendon Press, International Series of Monographs on Physics, 1999. 34. Black, M.R., et al., Infrared absorption in bismuth nanowires resulting from quantum confinement, Phys. Rev. B, 65, 195417, 2002. 35. Bruggeman, D.A.G., Calculation of various physics constants in heterogenous substances I: Dielectricity constants and conductivity of mixed bodies from isotropic substances, Ann. Phys., 24, 636, 1935. 36. Maxwell-Garnett, J.C., Colours in metal glasses and in metallic films, Philos. Trans. R. Soc. London, Ser. A, 203, 385, 1904. 37. Beaurepaire, E., et al., Coherent terahertz emission from ferromagnetic films excited by femtosecond laser pulses, Appl. Phys. Lett., 84, 3465, 2004.
7525_C003.indd 116
11/15/07 10:52:23 AM
Time-Resolved Terahertz Spectroscopy
117
38. Hilton, D.J., et al., Terahertz emission via ultrashort-pulse excitation of magnetic metal films, Opt. Lett., 29, 1805, 2004. 39. Welsh, G.H., Hunt, N.T., and Wynne, K., Terahertz-pulse emission through laser excitation of surface plasmons in a metal grating, Phys. Rev. Lett., 98, 2007. 40. Han, P.Y. and Zhang, X.C., Coherent, broadband midinfrared terahertz beam sensors, Appl. Phys. Lett., 73, 3049, 1998. 41. Kaplan, A.E., Diffraction-induced transformation of near-cycle and subcycle pulses, J. Opt. Soc. Am. B-Opt. Phys., 15, 951, 1998. 42. Han, P.Y., Huang, X.G., and Zhang, X.C., Direct characterization of terahertz radiation from the dynamics of the semiconductor surface field, Appl. Phys. Lett., 77, 2864, 2000. 43. Johnston, M.B., et al., Simulation of terahertz generation at semiconductor surfaces, Phys. Rev. B, 65, 165301, 2002. 44. Pedersen, J.E., et al., Terahertz pulses from semiconductor-air interfaces, Appl. Phys. Lett., 61, 1372, 1992. 45. Sipe, J.E. and Shkrebtii, A.I., Second-order optical response in semiconductors, Phys. Rev. B, 61, 5337, 2000. 46. Jepsen, P.U., Jacobsen, R.H., and Keiding, S.R., Generation and detection of terahertz pulses from biased semiconductor antennas, J. Opt. Soc. Am. B-Opt. Phys., 13, 2424, 1996. 47. Leitenstorfer, A., et al., Femtosecond charge transport in polar semiconductors, Phys. Rev. Lett., 82, 5140, 1999. 48. Leitenstorfer, A., et al., Femtosecond high-field transport in compound semiconductors, Phys. Rev. B, 61, 16642, 2000. 49. Castro-Camus, E., et al., Polarization-sensitive terahertz detection by multicontact photoconductive receivers, Appl. Phys. Lett., 86, 2005. 50. Yariv, Y. and Yeh, P., Optical Waves in crystals: propagation and control of laser radiation. New York: Wiley, 1984. 51. Rice, A., et al., Terahertz optical rectification from (110) zincblende crystals, Appl. Phys. Lett., 64, 1324, 1994. 52. Butcher, P.N. and Cotter, D., The elements of nonlinear optics. Cambridge: Cambridge University Press, 1990. 53. Smirnov, S.N. and Braun, C.L., Advances in the transient dc photocurrent technique for excited state dipole moment measurements, Rev. Sci. Instrum., 69, 2875, 1998. 54. Atkins, P., Physical chemistry. ed. 6. New York: W. H. Freeman, 1997. 55. Beard, M.C., Turner, G.M., and Schmuttenmaer, C.A., Measuring intramolecular charge transfer via coherent generation of THz radiation, J. Phys. Chem. A, 106, 878, 2002. 56. Beard, M.C., Schmuttenmaer, C.A., Using the finite-difference time-domain pulse propagation method to simulate time-resolved THz experiments, J. Chem. Phys., 114, 2903, 2001. 57. Cote, D., Sipe, J.E., and van Driel, H.M., Simple method for calculating the propagation of terahertz radiation in experimental geometries, J. Opt. Soc. Am. B-Opt. Phys., 20, 1374, 2003. 58. Guidoni, L., Beaurepaire, E., and Bigot, J.Y., Magneto-optics in the ultrafast regime: thermalization of spin populations in ferromagnetic films, Phys. Rev. Lett., 89, (2002). 59. Koopmans, B., et al., Ultrafast magneto-optics in nickel: Magnetism or optics?, Phys. Rev. Lett., 85, 844, 2000. 60. Beaurepaire, E., et al., Ultrafast spin dynamics in ferromagnetic nickel, Phys. Rev. Lett., 76, 4250, 1996.
7525_C003.indd 117
11/15/07 10:52:24 AM
118
Terahertz Spectroscopy: Principles and Applications
61. Wynne, K. and Carey, J.J., An integrated description of terahertz generation through optical rectification, charge transfer, and current surge, Opt. Commun., 256, 400, 2005. 62. Gallot, G. and Grischkowsky, D., Electro-optic detection of terahertz radiation, J. Opt. Soc. Am. B-Opt. Phys., 16, 1204, 1999. 63. Nahata, A., et al., Coherent detection of freely propagating terahertz radiation by electro-optic sampling, Appl. Phys. Lett., 68, 150, 1996.
7525_C003.indd 118
11/15/07 10:52:24 AM
Section II Applications in Physics and Materials Science
7525_S002.indd 3
11/8/07 2:27:23 PM
7525_S002.indd 4
11/8/07 2:27:23 PM
4
Time-Resolved Terahertz Studies of Carrier Dynamics in Semiconductors, Superconductors, and Strongly Correlated Electron Materials Robert A. Kaindl
Lawrence Berkeley National Laboratory
Richard D. Averitt Boston University
Contents 4.1 4.2
4.3
4.4
Introduction.................................................................................................. 120 Bulk and Nanostructured Semiconductors.................................................. 121 4.2.1 Overview........................................................................................... 121 4.2.2 Free Carrier Dynamics in Bulk Semiconductors............................. 122 4.2.3 Intraexcitonic Spectroscopy.............................................................. 128 4.2.4 Intersubband Transitions................................................................... 134 Superconductors........................................................................................... 136 4.3.1 Overview........................................................................................... 136 4.3.2 Far-IR Spectroscopy of Superconductors......................................... 137 4.3.3 Quasiparticle Dynamics in Conventional Superconductors............. 142 4.3.4 Quasiparticle Dynamics in High-TC Superconductors..................... 145 Half-Metallic Metals: Manganites and Pyrochlores.................................... 150 4.4.1 Overview........................................................................................... 150 4.4.2 Optical Conductivity and Spectral Weight Transfer......................... 152
Written while at Los Alamos National Laboratory.
119
7525_C004.indd 119
11/15/07 11:08:05 AM
120
Terahertz Spectroscopy: Principles and Applications
4.4.3 Dynamic Spectral Weight Transfer in Manganites.......................... 153 4.4.4 Carrier Stabilization in Tl2Mn2O7 through Spatial Inhomogeneity.................................................................................. 155 4.5 Summary and Outlook................................................................................. 158 Acknowledgments................................................................................................... 160 References............................................................................................................... 160
4.1 Introduction Perhaps the most important aspect of contemporary condensed matter physics involves understanding strong Coulomb interactions among the large numbers of electrons in a solid. Electronic correlations lead to the emergence of new system properties, such as metal–insulator transitions, superconductivity, magnetoresistance, Bose-Einstein condensation, the formation of excitonic gases, or the integer and fractional quantum Hall effects. The discovery of high-TC superconductivity in particular was a watershed event, leading to dramatic experimental and theoretical advances in the field of correlated-electron systems.1–10 Such materials often exhibit competition among the charge, lattice, spin, and orbital degrees of freedom, whose cause–effect relationships are difficult to ascertain. Experimental insight into the properties of solids is traditionally obtained by time-averaged probes, which measure, for example, linear optical spectra, electrical conduction properties, or the occupied band structure in thermal equilibrium. Many novel physical properties arise from excitations out of the ground state into energetically higher states by thermal, optical, or electrical means. This leads to fundamental interactions between the system’s constituents, such as electron–phonon and electron–electron interactions, which occur on ultrafast timescales. Although these interactions underlie the physical properties of solids, they are often only indirectly inferred from time-averaged measurements. Time-resolved spectroscopy, consequently, is playing an ever increasing role to provide insight into light–matter interaction, microscopic processes, or cause–effect relationships that determine the physics of complex materials. Experiments using visible and near-infrared (IR) femtosecond pulses have been extensively employed (e.g., to follow relaxation and dephasing processes in metals and semiconductors).11,12 However, many basic excitations in strongly correlated electron systems and nanoscale materials occur at lower energies. The terahertz (THz) regime is particularly rich in such fundamental resonances. This includes ubiquitous lattice vibrations and low-energy collective oscillations of conduction charges. In nanoscale materials, band structure quantization also yields novel IR and THz transitions, including intersubband absorption in quantum wells. The formation of excitons in turn leads to lowenergy excitations analogous to interlevel transitions in atoms. In transition-metal oxides, fundamental excitation gaps arise from charge pairing into superconducting condensates and other correlated states. This motivates the use of ultrafast THz spectroscopy as a powerful tool to study light–matter interactions and microscopic processes in nanoscale and correlated-electron materials. A distinct advantage of coherent THz pulses is that the amplitude and phase of the electric field can be measured directly, because the THz fields are coherent with
7525_C004.indd 120
11/15/07 11:08:06 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
121
the femtosecond pulses from which they are generated. Using THz time domain spectroscopy (THz-TDS), both the real and imaginary parts of the response functions, such as the dielectric function ε(w) = ε1(w) + iε2(w), are obtained directly without the need for Kramers-Kronig transforms.13 The THz response can also be expressed in terms of absorption a(w) and refractive index n(w), or as the optical conductivity s(w) ≡ s1(w) + is2(w) = iwε0[1-ε(w)]. The conductivity s(w) describes the current response J(w) = s(w)E(w) of a many-body system to an electric field, an ideal tool to study conducting systems. A second important advantage is the ultrafast time resolution that results from the short temporal duration of the THz time domain sources. In particular, optical pump THz probe spectroscopy enables a delicate probe of the transient THz conductivity after optical photoexcitation. These experiments can provide insight into quasiparticle interactions, phase transitions, or nonequilibrium dynamics. In this chapter, we will provide many such examples. Because THz spectroscopy of solids is a quickly expanding field of research, we must define a limited scope to be covered in this chapter. We will review studies of semiconductors, superconductors, and strongly correlated electron systems using few-cycle IR pulses that are accessible to direct field-resolved detection. This entails a photon energy range from below 4 meV (≈1 THz) to about 100 meV. We specifically omit measurements with “conventional” time-averaged techniques such as Fourier transform IR spectroscopy,1,14 and we will skip experiments that are covered elsewhere in this book, such as THz studies of semiconductor nanocrystals or THz sideband generation on intersubband transitions. In Section 4.2, we discuss quasiparticle dynamics in bulk semiconductors and nanostructured materials such as gallium arsenide (GaAs) quantum wells. This includes the free carrier response, the formation of quasiparticles, intraexcitonic spectroscopy, and the nonlinear response of intersubband transitions. In Section 4.3, we consider the THz response and dynamics in conventional superconductors, and in the high-TC superconductors YBCO and Bi-2212. As we will show, with optical pump THz probe spectroscopy, it is possible to simultaneously monitor quasiparticle and superconducting condensate fractions with subpicosecond temporal resolution. Dynamics in half-metallic transition metal oxides La0.7Ca0.3MnO3 and the pyrochlore Tl2Mn2O7 are presented in Section 4.4. Colossal magnetoresistance is observed in both materials, and time-resolved THz spectroscopy provides insight into the relevance of the spin degree of freedom for charge transport and carrier lifetimes. Finally, in Section 4.5, we provide a summary and offer suggestions for future experiments on nanoscale and correlated-electron materials using time-resolved THz spectroscopy.
4.2 Bulk and Nanostructured Semiconductors 4.2.1 Overview In this section, we review low energy excitations and carrier dynamics in bulk and nanostructured semiconductors as determined via coherent THz spectroscopy. The revolutionary impact of semiconductors on modern technology goes hand in hand with an extremely high atomic-scale precision in their manufacture and with an
7525_C004.indd 121
11/15/07 11:08:08 AM
122
Terahertz Spectroscopy: Principles and Applications
immensely detailed knowledge of their physical properties that is presently unattainable for the strongly correlated electron systems discussed in later sections. This makes semiconductors an ideal testing ground for novel physical concepts and experiments and for tailored optoelectronic devices. Femtosecond laser pulses in the visible and near-IR have been extensively used to study photoexcited carriers in semiconductors. Such pulses are resonant to the typically 1–2 eV band gaps. Experiments have progressed from pump–probe and luminescence to modern multidimensional coherent spectroscopies which all provide deep insight into relaxation timescales, inter-band coherences, or many-body correlations.11,12,15 As we will show in this section, semiconductors provide equally interesting and fundamental excitations at energies far below their valence-to-conduction band gaps. Here, time domain THz and optical pump THz probe studies are powerful techniques to discern excitations that remain inaccessible to visible light and to probe conduction processes at frequencies comparable to relaxation processes in these materials.
4.2.2 Free Carrier Dynamics in Bulk Semiconductors The simplest description of free carriers in response to an applied electric field in a doped or photoexcited semiconductor (or other conducting material) is given by the Drude model. In this model, carriers elastically scatter with a rate τ -1. The complex Drude conductivity is given as
s(w ) =
s DC 1 - iwτ
(4.1)
where the DC conductivity sDC is given by
s DC ≡ ne 2 τ/m = ne m = ε 0 w 2p τ.
(4.2)
In this equation, n is the carrier density, t the collision time, m* the effective mass, µ the mobility, ε0 the free space permittivity and wp the bare plasma frequency. While the Drude response can be derived from very simple considerations, it is important to emphasize that its validity is much broader. In fact, the Drude response can be derived from the semi-classical Boltzmann transport equation and even more rigorously from Kubo-Greenwood formalism.16 For example, using a Boltzmann approach, it is easy to show that s DC =
e2 〈 l F 〉 SF 12 p3
(4.3)
where is the mean free path averaged over the Fermi surface, and SF is the area of the Fermi surface. For a spherical Fermi surface this is equivalent to the Drude result highlighting that the relevant electrons are those at the Fermi surface with velocity vF. The Drude model serves as a useful starting point for understanding the properties and time evolution of many materials, as we will see time and again throughout this chapter. In superconductors, for instance, the spectral weight associated with a
7525_C004.indd 122
11/15/07 11:08:11 AM
123
Time-Resolved Terahertz Studies of Carrier Dynamics
normal state Drude response downshifts into a zero-frequency d function associated with the superconducting condensate upon cooling below the transition temperature TC. In manganites, the Drude spectral weight is transferred to higher energies as phonon and spin fluctuations transform the coherent free carrier response into a hopping-like polaronic response. In this sense, changes in the Drude response due to thermal or nonequilibrium perturbations serve as a sensitive probe of interactions or the onset of correlations. Deviations from the Drude model are, of course, often observed. They have been treated via a frequency-dependent scattering rate17 or a distribution of scattering times,18 but the Drude model is an essential starting point even in these cases. In the literature (and throughout this chapter) the Drude response is plotted in various ways. Figure 4.1 shows the calculated Drude response as a function of reduced frequency w/ws where ws is the screened plasma frequency (ws = wp /√e∞) for sDC = 4 × 104 W-1 cm-1, t = 200 fs, ∇wp = 0.1 eV (or wp /2p = 24.2 THz), and e∞ = 4. The complex conductivity is plotted in Figure 4.1a, with the real part s1(w) shown as the solid line and the imaginary part s2(w) by the dashed line. Note that s2(w) = s1(0)/2 at 1/t, which provides a direct intuitive measure of the scattering rate. Figure 4.1b shows the corresponding reflectivity R, which drops dramatically at ws where the electrons no
1
3
Reflectivity
σ/104(Ω cm)−1
4
2 1 0
0.8 0.6 0.4 0.2
0
0
0.1 0.2 0.3 0.4 Frequency (ω/ωs)
0
(a)
0.5 1 1.5 Frequency (ω/ωs)
2
0.5 1 1.5 Frequency (ω/ωs)
2
(b)
4 −lm(1/ε), Re(1/ε)
εreal
0 −10 −20 −30
2 0 −2
0.5
1 Frequency (ω/ωs) (c)
1.5
0
(d)
Figure 4.1 Example of the Drude response plotted in terms of (a) the real part (solid line) and imaginary part (dashed) of the complex conductivity σ(ω), (b) the reflectivity R(ω), (c) the real part ε1(ω) of the permittivity, and (d) the loss function shown as –Im(1/ε) (solid line) and Re(1/ε) (dashed). Frequencies are scaled to the screened plasma frequency ωs = ωp /√ε∞.
7525_C004.indd 123
11/15/07 11:08:14 AM
124
Terahertz Spectroscopy: Principles and Applications
longer respond to the applied field. At higher frequencies, R rises again to the value (1 - √e∞)2/(1 + √e∞)2. Quite often, the real part of e(w) is plotted as in Figure 4.1(c), where it is negative below ws increasing to e∞ at higher frequencies. Finally, the Drude response is sometimes displayed as in Figure 4.1(d), where the loss function -Im(1/e(w)) peaks at the screened plasma frequency ws with a line width 1/t. As an example of a Drude-like response, Figure 4.2 shows the results of THz-TDS measurements on lightly doped silicon19, with carrier density n ≈ 1015 cm-3. Figure 4.2a displays the real conductivity σ1(ω) for n-type and p-type samples with the corresponding imaginary conductivity σ2(ω) displayed in (b). This data highlights some specific advantages of THz-TDS. As mentioned earlier, the time domain THz measurement provides the real and imaginary parts of σ(ω) directly. Moreover, the signal-to-noise in THz-TDS is sufficient to test various conductivity models. For
6 Re Conductivity (1/Ω cm)
n-type, 0.21 Ω cm Si p-type, 0.17 Ω cm Si
(a)
5
4-point Probe 4 3 2 1 0
lm Conductivity (1/Ω cm)
3.0
(b)
2.5 2.0 1.5
Drude Cole-Davidson Lattice Scattering Impurity Scattering Lattice - Impurity Scattering
1.0 0.5 0
0
0.5
1
1.5
2
2.5
Frequency (THz)
Figure 4.2 Terahertz conductivity of n-type and p-type doped silicon, showing (a) the real part s1(w) and (b) the imaginary part s2(w). Lines represent fits to various Drude-like conductivity models as indicated. (Reprinted with permission. Copyright 1997 by the American Physical Society.)
7525_C004.indd 124
11/15/07 11:08:17 AM
125
Time-Resolved Terahertz Studies of Carrier Dynamics
both the n-type and p-type samples, the response cannot be fully explained with the Drude model. Rather, the best experimental fit is obtained with the Cole-Davidson model s(w ) =
s DC . (1 - iwτ )β
(4.4)
Here, β describes a distribution of relaxation times, such that the average scattering time <τ> is given by τβ.19 Thus, β = 1 reduces to the Drude response. For the data in Figure 4.2, a best fit was obtained with β = 0.84 (0.76) for the n-type (p-type) samples. A pure Drude response (i.e. β = 1) was obtained for samples with somewhat higher carrier densities around ≈ 1017 cm-3.19 With optical pump THz probe spectroscopy, measurements of the Drude conductivity upon photoexcitation of electron hole pairs have been performed by several groups.20–22 Some experiments are described in more detail in the chapter by Schmuttenmaer. One example of a photo-induced Drude-like response we would like to highlight is the result on GaAs as reported by Huber and Coworkers in Ref. 23. These results provide a striking example of the ultrafast evolution of the THz response during the development of many-body correlations following photoexcitation. In this experiment, pulses with 1.55-eV photon energy and approximately10 fs duration excited an electron hole (e-h) plasma at a density of 1018 cm-3. Monitoring the dynamics requires THz probe pulses with sufficient temporal resolution and with a spectral bandwidth extending beyond 40 THz. This was achieved using a scheme based on difference frequency generation in GaSe combined with ultrabroadband free space electrooptic sampling.23–25 The experimental results are displayed in Figure 4.3, where the THz spectra of the dynamic loss function 1/ε(ω,τD) are plotted at various delays τD between the optical pump and THz probe pulses. The imaginary part of 1/ε(ω,τD) is plotted in panel (a) and the real part in panel (b). As explained by the authors of Ref. 23, this highlights the evolution of particle interactions from a bare Coulomb potential Vq to a screened interaction potential Wq(ω,τD), where q is the momentum exchange between two particles during a collision: Vq =
Vq 4 pe 2 . → Wq (w, τ d ) ≡ 2 ε q (w, τ d ) q
(4.5)
In essence, Vq becomes renormalized by the longitudinal dielectric function leading to a retarded response associated with the polarization cloud about the carriers. This is a many-body resonance at the plasma frequency ωs and as described previously in Figure 4.1(d), the loss function peaks at ωs with a width corresponding to the scattering rate. Thus, the results of Figure 4.3 show the evolution at q = 0 from an uncorrelated plasma to a many-body state with a well-defined collective plasmon excitation. This is evident in Figure 4.3(a) where, prior to photoexcitation, there is a well-defined peak at 36 meV corresponding to polar optical phonons. Following photoexcitation, a broad resonance appears at higher energies that evolves on a 100-fs timescale into a narrow plasma resonance centered at 14.5 THz. The response
7525_C004.indd 125
11/15/07 11:08:20 AM
126
Terahertz Spectroscopy: Principles and Applications
0
30
60
90
0.8
Energy (meV) 120
0
30
60
90
Drude
120
Drude
0.6
0.4
tD =
0.3
0
175 fs
0.0
150 fs
–0.3
125 fs
Re(1/(εq=0(ω,tD))
–lm(1/εq=0 (ω, tD))
Energy (meV)
100 fs 75 fs 50 fs 25 fs 0 fs Polar Lattice 0
5
10 15 20 25 30 35 Frequency (THz) (a)
0
5
10 15 20 25 30 35 Frequency (THz) (b)
Figure 4.3 Quasiparticle formation in GaAs after excitation with 10-fs 1.55-eV pulses. The dynamic loss function is plotted as a function of frequency at various delays after photoexcitation. The dynamic response evolves to a coherent Drude response on a timescale of ~175 fs as dressed quasiparticles are formed from an initially uncorrelated state at zero delay. (Reprinted with permission. From Huber, R. et al., Nature 414, 286–289, 2001.)
is described by the Drude model only at late delay times. These results are consistent with quantum kinetic theories describing nonequilibrium Coulomb scattering.23 As a further example related to free carriers in doped semiconductors, we consider the response at high THz electric fields26 with E > 100 kV/cm. Several groups are pursuing high field THz generation using various approaches including large aperture photoconductors,27 polaritons,28 and transition radiation at the plasma- vacuum boundary.29 A recently developed technique based on four-wave-mixing of the fundamental and second harmonic of a Ti:sapphire laser has been used to generate THz pulses with peak field strengths greater than 400 kV/cm. In Ref. 26, Bartel et al., focused amplified near-IR pulses with 25-fs duration into nitrogen with a 100 µm BBO crystal placed before the focus.26 The fundamental and second harmonic interact at the focus through a χ(3) process to efficiently generate THz radiation. This source of THz radiation was subsequently used by Gaal et al., in terms to induce a nonlinear response in n-type GaAs chemically doped to a carrier density of 1017cm-3.30 In this experiment, the transmission of high peak field THz pulses (E > 50 kV/cm) was compared to the transmission of lower field strength THz pulses (<1 kV/cm). Figure 4.4(a) shows the incident and transmitted THz electric field in the time domain, and Figure 4.4(b) displays the corresponding spectra. The sample is placed at the focus of an off-axis
7525_C004.indd 126
11/15/07 11:08:24 AM
127
Time-Resolved Terahertz Studies of Carrier Dynamics
(a)
(b) Ein(t)
0
50
Electric Field (kV/cm)
Eout(t) 20 kV/cm 10
(c)
0
(d)
5
5
Spectral Power (arb. u.)
Sample
0
0 –5 Eout(t) – Ein(t)
–10 –1
0
1
2
Time (ps)
3 0
–5 |Eout(ν)|2 – |Ein(ν)|2 2
4
–10
Frequency ν (THz)
Figure 4.4 Nonlinear THz transmission through GaAs. (a) Incident and transmitted pulses in the time domain and (b) corresponding spectrum of the pulses. (c) Time domain difference between the incident and transmitted pulses clearly highlight the oscillations following the main transient. In (d), the solid line is the difference in spectral power for low peak field transmission while the diamonds show high peak field results. (Reprinted with permission. Copyright 2006 by the American Physical Society.)
parabola (inset). In Figure 4.4(c), the difference between incident and transmitted pulses reveals a 500-fs oscillation persisting after the main THz transient. This is more striking in the frequency domain, plotted as the difference in spectral power in Figure 4.4(d). The solid line shows the low-field THz response, where the data is negative at all frequencies as expected for a Drude response. In contrast, for the highfield response (diamonds), a strong increase in the spectral power is observed over a narrow frequency range around 2 THz. This result was explained by Gaal et al., in terms of the superradiant decay of optically inverted impurity transitions in bulk GaAs. In this novel process that occurs at high THz fields, the incident field strength is sufficient to ionize a significant fraction of s-like neutral donors through excitation into continuum states. A fraction of the excited carriers are subsequently scattered to p-like impurity states, followed by stimulated emission of dipole-allowed p → s transitions. A calculation based on a single-particle Schrödinger equation with randomly distributed donors is consistent with this interpretation.
7525_C004.indd 127
11/15/07 11:08:27 AM
128
Terahertz Spectroscopy: Principles and Applications
4.2.3 Intraexcitonic Spectroscopy Bound e-h pairs (excitons) bring about strong modifications of the optical and electronic properties of semiconductors. Sharp exciton lines in the visible or near‑IR are often observed around the bandgap, which provides the basis for the widely employed absorption and luminescence studies based on exciton photogeneration and annihilation.12,31 This contrasts sharply with intraexcitonic resonances,32,33 which are low-energy electromagnetic transitions between internal exciton levels as illustrated in Figure 4.5(a). Because exciton binding energies typically range between 1 and 100 meV, intraexcitonic transitions occur at THz frequencies. The sensitivity to transitions within existing exciton populations makes them an ideal tool to probe the absolute pair densities and the low-energy structures of excitonic gases. This differs from near-IR absorption and luminescence studies, which couple strongly to only a subset of states around K ≈ 0 (optical light cone) because of momentum conservation, and are thus dependent on both exciton density and the energy distribution functions in a complex way. Because intraexcitonic transitions are due to changes of the relative momentum of the e-h pair, they can occur at much larger center-of-mass momenta K outside the visible light cone. Moreover, as discussed in the following section,
4
Continuum 2p 1s THz THz
Near-IR
Momentum K
Induced Conductivity Δσ1(ω) (Ω–1 cm–1)
e-h Pair Energy
Photon Energy (meV) 6 8 10 4 6 8
20
10 (b)
10
10
0
0
(c) 0
0
Dielectric Function Change Δε1(ω)
(a)
–10
–10 1
1 2 Frequency (THz)
2
Figure 4.5 Intraexcitonic spectroscopy. (a) Schematic dispersion of excitons and unbound eh pairs along their center‑of‑mass momentum. Arrows indicate near-infrared photogeneration of excitons, as well as intraexcitonic 1s-2p transitions. (b) Measured THz response in GaAs quantum wells (circles) 5 ps after resonant excitation at the 1s heavy hole exciton line, at low temperature (T = 6 K). Lines represent intraexcitonic model curve for density 3 × 1010 cm-2. (c) Response after nonresonant excitation into the continuum at T = 300 K. In the experiments, photoexcitation of free carriers in the substrate was avoided by etching off the substrate, leaving only the quantum well structure and surrounding cladding layer attached to a THz-transmitive MgO substrate.
7525_C004.indd 128
11/15/07 11:08:30 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
129
so-called “dark excitons” with a forbidden inter-band dipole moment are easily accessible via intraexcitonic spectroscopy. These arguments strongly motivate the use of intraexcitonic THz probes as new tools for exciton spectroscopy. Intraexcitonic spectroscopy is a rising field with an increasing breadth of applications. Early studies took advantage of the long recombination times in indirect semiconductors such as Ge, which enabled measurements using conventional infrared spectrometers.34 The development of modern time-resolved THz spectroscopy gives access to a much larger range of materials, and enables studies of the ultrafast dynamics of excitons via intraexcitonic probes.35–38 Their use to study fundamental exciton physics is strongly supported by recent microscopic calculations, which contrast the information gained to that of luminescence and predict significant changes of the THz spectrum in low-temperature excitonic phases.39–41 We first discuss optical pump THz probe experiments that detect intraexcitonic resonances to directly observe exciton formation and ionization dynamics.37 These experiments were performed on a GaAs multiple-quantum well sample, which at the lowest temperatures (6 K) exhibits a sharp near-IR absorption line of 1s heavy hole excitons followed by higher bound exciton lines and the broadband continuum. A 250-kHz regenerative Ti:sapphire amplifier delivering 150-fs pulses at 800 nm was used to generate and probe THz pulses in the 2–12 meV range via optical rectification and electrooptic sampling in 500‑µm thick ZnTe crystals. The high repetition rate of this setup provides both sensitive detection with 104:1 signal-to-noise ratio in the THz electric field and sufficiently high µJ pulse energies to photoexcite the large THz probe areas. Near-IR pump pulses were spectrally narrowed to 2 meV and tuned to selectively excite either the sharp 1s exciton line or the continuum of unbound e-h pairs. In a first experiment, the THz response at low lattice temperatures was studied after resonant photoexcitation at the 1s–HH exciton line. The THz response is expressed as σ(ω) = σ1(ω) + iωε0[1 - ε1(ω)], where σ1(ω) measures the absorbed power density and ε1(ω) the inductive out-of-phase response. Just after photoexcitation, as shown in Figure 4.5(b), the THz response consists of a strongly asymmetric peak around 1.7 THz in ∆σ1 accompanied by a dispersive dielectric function change ∆ε1 at the same frequency. This response corresponds to the formation of a new, low-energy oscillator that is absent in the semiconductor’s ground state. The THz conductivity peak can be explained by the lowest energy intraexcitonic transition, i.e., between the 1s → 2p exciton levels, in agreement with known level spacings. After excitation into the continuum of unbound states, a very different behavior is observed. Figure 4.5(c) shows data taken with the sample at room temperature to minimize the influence of excitonic correlations. The THz response then exhibits a pure Drude response of a conducting e‑h gas. It is characterized by a large lowfrequency conductivity ∆σ1 and a purely negative dielectric function change ∆ε1. Note in contrast the vanishing low-frequency THz conductivity for the intraexcitonic response in Figure 4.5(b), which results from the insulating, charge-neutral nature of the bound e-h pairs. An important advantage of intraexcitonic spectroscopy is its capability to provide an absolute measure of exciton densities. A quantitative intraexcitonic dielectric function ε(ω) of an exciton gas in the ground state can be derived by summing
7525_C004.indd 129
11/15/07 11:08:31 AM
130
Terahertz Spectroscopy: Principles and Applications
up the dipole transitions between the 1s level and the higher bound and continuum states. The solid lines in Figure 4.5(b) are such calculations, using two-dimensional bound and continuum hydrogenic wave functions corrected for Coulomb screening effects from the finite well width of the quasi–two-dimensional system.42–44 A reduced effective mass µ = 0.054 m 0 and a dielectric constant εs = 13.2 were used for the GaAs quantum well material. The calculation shows that, although the peak is due to the 1s-2p transition, the shoulder stems from transitions into higher bound np levels and the continuum. Within a parabolic band approximation, we can write the “partial oscillator strength sum rule” as WB
∫
s1 (w )dw =
0
p ne 2 2 m
(4.6)
∆t = 0 ps
0
60 ps
10 0 –10 –20
20 hv 10
200 ps 0
400 ps 1,000 ps 4
6
8 10
4
6
8 10
–10 0
200
400
600
800 1,000
Photon Energy (meV)
Time Delay (ps)
(a)
(b)
Dielectric Function Change, ∆ε1, at 4.1 meV
10
∆ε1(ω)
∆σ1(ω) (Ω–1 cm–1)
where n is the e-h pair density. According to Equation 4.6, the intraband spectral weight up to energies WB below the interband transitions is directly determined by the e-h pair density n and reduced mass µ. This renders THz probes an important direct gauge of e-h pair and exciton densities, in strong contrast to more indirect measures of luminescence or absorption spectroscopy at the band gap. Optical pump THz probe experiments have been employed to investigate the formation and ionization dynamics of excitons.37 Figure 4.6 shows the low- temperature transient THz response after nonresonant excitation above the bandgap. Directly after excitation into the unbound e-h continuum (∆t = 0 ps), the THz response is spectrally broad, with a negative dielectric function change ∆ε1 that closely follows a Drude model (solid line, Figure 4.6(a)). The system is thus dominated by a conducting gas of unbound e-h pairs, as also substantiated by the large
Figure 4.6 Exciton formation in GaAs quantum wells at T = 6 K, studied via intraexcitonic spectroscopy. (a) Induced THz conductivity ∆σ1 and dielectric function change ∆ε1 after nonresonant excitation into the continuum, for different pump-probe delays ∆t. Solid line at ∆t = 0 ps: Drude model. (b) Dynamics of ∆ε1 at 1 THz, which illustrates the decay of the Drude-like response of the unbound e-h pairs while excitons continue to form. (Reprinted with permission. From Kaindl, R.A. et al., Nature 423, 734–738, 2003.)
7525_C004.indd 130
11/15/07 11:08:36 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
131
low-frequency conductivity. However, the induced conductivity ∆σ1 already at this time point deviates significantly from the Drude model, showing a distinct excitonic peak around 8 meV. This peak signifies the quasi-instantaneous appearance of excitonic e-h correlations directly after continuum excitation, within the ≈1-ps time resolution of the experiment. As the system evolves over several hundred picoseconds the exciton peak increases in spectral weight and sharpens, whereas the Drude components of the response decay away. This reveals two very different time scales that exist during exciton formation. Acoustic phonon emission can explain the slow scattering of unbound e-h pairs into excitons on a 100-ps time scale.45–47 In contrast, the quasi-instantaneous exciton peak can be explained by a much faster process, such as ultrafast Coulomb interactions in the photoexcited e-h gas. The opposite process of exciton ionization at increased lattice temperatures can be studied, in which intraexcitonic spectroscopy provides quantitative insight into the dynamics of exciton breakup and into the resulting quasi-equilibrium mixture of excitons and unbound pairs.37,44 Further experiments also studied the intraexcitonic response of a high-density exciton gas.48 Those results show an increasing free carrier fraction as the photoexcitation density is increased, accompanied by a strong renormalization of the 1s-2p resonance to lower energies. Although the previous experiments have studied intraexcitonic absorption, it was suggested early on to reverse this process to induce THz gain from inverted exciton populations.33 The search for intraexcitonic gain is, however, nontrivial because excitons differ strongly from atomic gases. Excitons interact with phonons and they typically exhibit significant many-body interactions such as phase-space filling, screening, and scattering. Also, in stark contrast to atoms, they are initially photogenerated as coherent polarization waves and possess an often short recombination lifetime. Recent calculations propose to obtain population inversion by exciting higher bound s‑like excitons and predict a transfer into p-like excitons via many-body interactions.50 A promising candidate for intraexcitonic stimulated THz emission is Cu2O, which exhibits a particularly well-defined excitonic Rydberg series. These visible lines shown in Figure 4.7(a) are due to p-like excitons,51 which makes this an ideal system to search for p → s intraexcitonic population inversion. Unlike most semiconductors, photoexcitation of s-like excitons in Cu2O is dipole-forbidden because the parity of valence and conduction bands is identical around the Brillouin zone center.51 A recent optical pump THz probe experiment provides the first demonstration of stimulated emission between internal exciton levels.49 In that study, a 330-µm thick Cu2O single crystal was resonantly photoexcited using spectrally shaped pump pulses around λ ≈ 570 nm. Figure 4.7(b) shows the THz response at ∆t = 1 ps. Excitation in the continuum leads to a broad Drude response (top curve), whereas excitation of 2p excitons (bottom curve) induces a broad THz absorption that can be explained by intraexcitonic transitions. A strikingly different response occurs after selective 3p excitation, as shown in the middle curve of Figure 4.7(b): here, a negative absorption change at 6.6 meV is observed, which is surrounded by absorption at higher and lower photon energies. This negative absorption is explained by 3p → 2s stimulated THz emission, commensurate with the known level spacing. It should be noted that Cu2O has no measurable absorption in this range, and that the effect occurs only after resonant 3p excitation. While the overall signals are small, the cross-section
7525_C004.indd 131
11/15/07 11:08:37 AM
Terahertz Spectroscopy: Principles and Applications
0
3p
–5
4s 3s
4d 3d
6 5
2s
–10
4
2p
–15
g 2p 2.13
3p
4p
5p
2.14 2.15 2.16 2.17 Photon Energy (eV) (a)
3 2 1
0 Continuum
–2
1.0 ∆t = 1 ps 0.5 0.0
–4
∆α(cm–1)
5p 4p
∆n(10–3)
5
Absorption Coefficient α (100 cm–1)
Energy (meV)
132
3p
2p 4
6
8 10 4 6 8 Photon Energy (meV)
10
(b)
Figure 4.7 Stimulated emission from intraexcitonic transitions. (a) Visible absorption spectrum of Cu2O at T = 6 K (solid line) and pump spectrum (dashed). Inset: exciton levels and their energy difference to the 3p level. (b) THz refractive index change ∆n (left panel) and induced absorption ∆α (right panel) 1 ps after continuum, 3p, or 2p excitation. Arrow indicates 3p-2s stimulated emission at 6.6 meV. (Reprinted with permission. Copyright 2006 by the American Physical Society.)
corresponds to a large value of σ ≈ 10 –14 cm2, which motivates further work toward generation of strong stimulated THz emission from excitons. The material Cu2O has also been of much interest for experiments that attempt to find Bose-Einstein condensation (BEC) of excitons in semiconductors. Exciton BEC was predicted in 1968 by Keldysh and Kozlov,52 but its observation has been elusive until now. The small exciton mass pushes the transition temperature upward into the Kelvin range, about 106 times higher than for atoms. Very intriguing effects were observed in coupled quantum wells,53,54 but Cu2O remains the longest and most extensively studied candidate material. It is a key contender for BEC because its lowest energy 1s exciton is dipole-forbidden and thus has an extremely long lifetime. Because of electron hole exchange interactions, the 1s exciton in Cu2O is split into the lowest energy paraexciton (singlet, S = 0) and a three-fold degenerate orthoexciton (triplet, S = 1) that lies 12 meV higher in energy (Figure 4.8(a). The paraexciton is optically inactive to all orders, and lifetimes from ≈0.1 to 1 ms have been reported. Luminescence experiments provided strongly differing interpretations: an early study suggested evidence for exciton BEC in Cu2O based on the luminescence line shape,55 but the same authors later questioned this56 and concluded that the densities for BEC may not be reached because of fast exciton–exciton Auger recombination above n ≈ 1015 cm–3. However, Auger recombination was shown to contradict recent results, and a fast exciton capture into short-lived biexcitons was proposed instead to explain the fast dynamics.57–59 Here, intraexcitonic spectroscopy promises new insights because of the lack of optical coupling of the 1s exciton in the visible inter-band range. Several intraexcitonic experiments were reported that probe the 1s-2p transitions in Cu2O crystals.38,60–64 Kubouchi et al. studied the picosecond dynamics of the intraexcitonic transitions of the lowest energy exciton species in a 170-µm thick Cu2O single crystal.38,63,64
7525_C004.indd 132
11/15/07 11:08:41 AM
133
Time-Resolved Terahertz Studies of Carrier Dynamics ortho 1s-2p
16 14 E
para 1s-2p
800 ps
12 2p-ortho
2p-para 1s-ortho
∆α(cm–1)
10
200 ps
8 6
30 ps
4
1s-para K
10 ps
2
–10 ps
0 110
(a)
120 130 Energy (meV) (b)
Figure 4.8 (a) Schematic level diagram of the lowest energy excitons in Cu2O, along with intraexcitonic transitions between the 1s and 2p levels. (b) Transient intraexcitonic absorption at 4.2 K for different time delays after two-photon resonant excitation of orthoexcitons with a 1220-nm wavelength pump beam. (Reprinted with permission. Copyright 2005 by the American Physical Society.)
As illustrated in Figure 4.8(a), the 1s-2p transitions within the paraexcitons occur at higher photon energies than within the orthoexcitons because of the different fine structure splittings of the 1s versus the 2p levels. Orthoexcitons in the 1s level are resonantly photogenerated in those experiments by two-photon excitation with a femtosecond pulse around the 1220-nm wavelength.38 The resulting absorption changes ∆α are followed in transmission between 108 and 140 meV photon energy (≈26–34 THz) on a picosecond timescale. As shown in Figure 4.8(b), the signals directly evidence a decrease of the orthoexciton density (116-meV peak) accompanied by a concomitant rise of the paraexciton density (129-meV peak) on a 100-ps time scale. This intraexcitonic study therefore shows directly that rapid orthoexciton decay arises from ortho-para exciton interconversion. This can be attributed by Kubouchi and coworkers to an electron spin exchange mechanism. Such experiments can provide new insight into the properties of the optically dark 1s excitons to optimize the conditions under which a possible degenerate excitonic quantum state may be generated. Moreover, calculations predict strong changes of the intraexcitonic spectra when the material undergoes a transition into the BEC state,39 which strongly motivates further work on intraexcitonic spectroscopy of low-temperature e-h gases.
7525_C004.indd 133
11/15/07 11:08:44 AM
134
Terahertz Spectroscopy: Principles and Applications
4.2.4 Intersubband Transitions The quantum confinement of carriers in semiconductor heterostructures leads to a splitting of the conduction and valence bands into subbands. New THz transitions can then occur between these subbands within the conduction band (or valence band) when a quasi two-dimensional carrier plasma is introduced into the structure by photoexcitation, electrical injection, or chemical doping. These intersubband transitions represent a totally new character of optoelectonic excitations below the fundamental band gap of a semiconductor, especially when compared with the broad near-IR interband absorption from the valence to conduction bands.65,66 A schematic band structure and a typical intersubband absorption line are shown in Figure 4.9. Because of the identical sign of the curvature of both subbands, the absorption is concentrated into a small interval of photon energies. Ideally, subbands with identical effective mass would result in a vanishing line width except for homogeneous broadening. However, a real semiconductor exhibits a nonparabolic band dispersion; transitions at different in-plane momenta then occur in a finite frequency interval, leading to inhomogeneous broadening. Sample imperfections and Coulomb manybody interactions further complicate intersubband line shapes. Intersubband transitions can be tailored to occur within a large photon energy range from approximately 1 to 100 THz via quantum heterostructure engineering. Technical applications of intersubband transitions are abundant, with unipolar quantum well photodetectors and quantum cascade lasers being particularly relevant devices.67,68 The operating principle of THz and mid-IR quantum cascade lasers relies directly on controlled engineering of ultrafast processes. Population inversion between subbands can be achieved by optimizing the electron tunneling and relaxation dynamics, and the photonic properties of quantum well and superlattice heterostructures. Numerous ultrafast THz and mid-IR studies of intersubband relaxation and dephasing have been reported. Intersubband relaxation and carrier thermalization E
CB (n = 2) (n = 1)
Intersubband
Interband
z (a)
VB k||
Absorption (norm)
E 1
0 20
25
30
35
Frequency (THz) (b)
Figure 4.9 Intersubband absorption. (a) Left: spatial variation of the conduction (CB) and valence band (VB) edges in the heterostructure growth direction, and energy extrema of the lowest subbands (horizontal lines). Right: dispersion along the two-dimensional layers and optical transitions. (b) Typical intersubband absorption line, measured from an n-type doped GaAs multiple quantum well structure.
7525_C004.indd 134
11/15/07 11:08:46 AM
135
Time-Resolved Terahertz Studies of Carrier Dynamics
have been observed in both n-type and p-type heterostructures, in which spectral changes around the intersubband line are sensitive to transient modifications of the carrier distribution function f(E).69–75 Near-IR photoexcitation of a coherent superposition of several bands also leads to THz emission, as a measure of intersubband or intervalence band oscillations.76–78 This yields information on the decay of intersubband coherence in undoped structures, equivalent to the overall intersubband line shape. Coherent emission was also detected from intersubband plasmons in parabolic quantum wells79 and from Bloch oscillations in superlattices that arise from different physics in high THz fields.80 Separation of homogeneous and inhomogeneous components of intersubband line shapes necessitates nonlinear experiments, realized through mid-IR femtosecond four-wave mixing experiments.81,82 Such timeresolved THz and mid-IR studies provide insight into energy and phase relaxation times and into microscopic carrier–carrier and carrier–lattice interactions of interest for fundamental physics and device design.83 Combined with high field strengths, coherent THz pulses offer new ways to measure and control coherent polarizations between quantized levels in quantum wells or other nanomaterials. Intense THz fields can lead to the generation of intersubband sidebands on the near-IR resonances and to undressing of collective depolarization effects.84,85 Rabi oscillations occur at the highest field strengths. The experiments of Luo et al., discussed in the following section, have provided a vivid example of direct field-resolved measurements in this regime.86 The experiment is illustrated in Figure 4.10(a). An incident coherent THz pulse couples to the (n = 1) to (n = 2) intersubband transition (νIS ≈ 24 THz) in the mid-IR spectral range of an n-type modulation-doped GaAs multiple quantum well structure. The electron density is 5 × 1010 cm–2 in each quantum well. A prism geometry enables strong coupling to the Probe
MIR
PS ZnTe
Sample Electric Field (kV/cm)
(a) 5
Incident
20 0
0 Re-emitted –5 0.0
0.2
0.4
0.6 0.8 Time (ps) (b)
–20 1.0
1.2
0.2
0.4
0.6 Time (ps) (c)
0.8
1.0
Figure 4.10 Rabi oscillations from intersubband transitions in GaAs multiple quantum wells. (a) Experimental scheme. (b) and (c) Measured field transients incident (thin line) and reemitted (thick line) from the sample, for two different THz field amplitudes of 5 kV/cm and 30 kV/cm. (Reprinted with permission. Copyright 2004 by the American Physical Society.)
7525_C004.indd 135
11/15/07 11:08:49 AM
136
Terahertz Spectroscopy: Principles and Applications
intersubband dipole moment oriented perpendicular to the quantum well layers. The incident and reemitted light fields are characterized in the time domain via electrooptic sampling using a 10-µm thick ZnTe crystal. Figures 4.10(b) and (c) show the incident field and the reemitted field for different field strengths. The incident field is determined by use of an inactive undoped sample. The emitted field in turn is obtained by subtracting the incident field from the total field transmitted through a doped sample. In the weak field limit shown in Figure 4.10(b), the reemitted THz field is 180° out of phase from the incident field. This corresponds to absorption of light at the intersubband transition; the incident field creates a coherent intersubband polarization, from which a coherent field is emitted (free induction decay) that partially cancels the incident THz pulse. At higher field strengths, Figure 4.10(c), the reemitted field changes drastically; initially it is out of phase, then vanishes and reappears as inphase with the driving field. Constructive interference with the reemitted field during the second half of the driving pulse corresponds to gain and thus to amplification of the incident field. This is a direct manifestation of Rabi oscillations between the (n = 1) and (n = 2) subbands. A detailed analysis of the data reveals deviations between the simplified two-level Maxwell-Bloch formalism and the measured field traces.86 This can be explained by a Coulomb-mediated collective coupling between different quantum well layers in the nanostructure.86–88 Intersubband coherent control via high-field THz pulses enables new quantum optical experiments in solids, with novel applications (e.g., in photonics and quantum information science). Rabi oscillations were also studied on hydrogenic 1s-2p transitions of donor impurities in GaAs,89 which serve as a model two-level system for such applications. Gain without inversion from intersubband transitions was recently experimentally observed.90 This also motivates coherent population transfer experiments to provide maximum control over THz excitations in nanostructures.91–93
4.3 Superconductors 4.3.1 Overview Far-IR spectroscopy has played an important role in the characterization of superconductors since the BCS phonon-mediated pairing mechanism was proposed and experimentally verified.94 Mattis and Bardeen described the electrodynamics of superconductors and the opening of a spectroscopic gap 2∆0 for quasiparticle excitations.95 In weak-coupling BCS theory, the gap value is given by 2∆0 = 3.5kBTC, with TC being the transition temperature. The electrodynamics was experimentally confirmed by Glover and Tinkham using far-IR techniques.10,96 Nonequilibrium superconductivity also has a long history starting with tunneling experiments.97 The formation of Cooper pairs—also called “quasiparticle recombination”—is a fundamental quantum process in a superconductor arising from the pairing of two unbound quasiparticles that are thermally or otherwise excited out of the condensate’s correlated ground state. It was soon realized that pair breaking by excess phonons complicated matters, as first described by the rate equations of Rothwarf and Taylor.98 Experimental and theoretical progress continued throughout the 1970s and 1980s.99–102 Ultrafast optical spectroscopy of metals blossomed when it was realized that the electron phonon coupling constant λ could be determined from such
7525_C004.indd 136
11/15/07 11:08:50 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
137
experiments.103–105 For example, this technique was used to measure λ for several conventional BCS superconductors.106 With the discovery of high-TC superconductors in the copper oxides (cuprates), it was realized that all-optical pump–probe spectroscopy could be used for nonequilibrium studies below TC.107,108 A limitation in the interpretation of such studies is that they probe the dynamics at visible or near-IR wavelengths, far above the superconducting gap and other intrinsic low-energy excitations. THz-TDS is a useful experimental tool to study superconductors.106,109 With optical photoexcitation, it provides what, to date, is probably the most insightful experimental approach to interrogate nonequilibrium dynamics in superconductors. Such experiments have the potential to measure quasiparticle interactions that remain hidden in linear spectroscopic measurements. In this section, we first describe linear IR spectra of superconductors using THz-TDS, with an emphasis on MgB2 and YBa2Cu3O7. This highlights commonalities and differences between conventional and high-TC superconductors in their THz electrodynamics. Armed with this knowledge, we proceed in the subsequent sections to time-resolved THz studies of nonequilibrium dynamics in the BCS superconductor MgB2, and in the high-TC cuprates YBCO and Bi-2212.
4.3.2 Far-IR Spectroscopy of Superconductors There is a vast literature on the electrodynamics of superconductors.1,10 Given these excellent reviews and space limitations we restrict our description to studies of superconductors using THz-TDS. The advantage of THz probes is that they significantly penetrate inside the bulk of the material to provide a contactless probe of low-energy excitations such as the superconducting energy gap and the collective superfluid condensate and quasiparticle response.110 Early time domain THz experiments on superconductors concentrated on studying the equilibrium conductivity of conventional metals such as NbN that exhibit an isotropic s-wave superconducting gap,13 and of high-TC cuprates109,111–113 with an anisotropic d-wave gap and more complex physics. In the following, we illustrate the THz response of a superconductor with a time domain THz study of MgB2.114 As discovered in 2001, this material turns superconducting below TC = 39 K, an unexpectedly high transition temperature for a conventional metallic compound.115 The THz experiments described below cover the 2 to 11-meV spectral range, with THz pulses generated and coherently detected using a 250-kHz Ti:sapphire amplifier. Experimental results are shown in Figure 4.11, as obtained from a 100-nm thick MgB2 film. The electric field of THz pulses transmitted through the film is shown in Figure 4.11(a). As the material transitions from the normal (dashed) into the superconducting state (solid line), the THz field increases in amplitude and shifts in phase. This field reshaping arises from changes to the complex conductivity σ(ω). The response is obtained via Fourier transformation of time domain THz signals and by evaluation of standard thin film transmission formulas.116 A useful way to analyze the electrodynamic properties of superconductors is to plot the ratio of the conductivity to its normal state value σN(ω). This is shown in Figures 4.11(b) and (c) for the real and imaginary parts, respectively. A strong depletion in the real part σ1(ω)/σN(ω) is evident in Figure 4.11(b) as the temperature is decreased below TC. An absorption onset occurs at ≈5 meV, as evident in the data,
7525_C004.indd 137
11/15/07 11:08:52 AM
138
Terahertz Spectroscopy: Principles and Applications
EO Signal
3 0 –3 –1
0 1 Time Delay (ps) (a)
2
1 1
0
5 10 Photon Energy (meV)
5 10 Photon Energy (meV)
(b)
(c)
σ2(ω)/σN(ω)
σ1(ω)/σN(ω)
2
0
Figure 4.11 Terahertz conductivity of a 100-nm thick film of MgB2. (a) Time-resolved THz fields measured in transmission at T = 6 K (solid line) and 40 K (dashed line). (b) and (c) Real part σ1(ω) and imaginary part σ2(ω) of conductivity normalized to the normal state (40 K) value σN (ω). Data are shown for T = 6 K (dots), 24 K (squares), and 30 K (triangles). Mattis-Bardeen calculations for an isotropic s-wave gap of magnitude 2∆0 = 5 meV, TC = 30 K, and T = 6 K are shown as thick solid lines. The dashed line in (b) also shows the same calculation for T = 24 K.
particularly at the lowest temperature, T = 6 K. This is the signature of the superconducting gap. The imaginary part σ2(ω)/σN(ω) in Figure 4.11(c) shows the buildup of a component in the superconducting state that strongly increases with decreasing frequency. The latter, 1/ω-like response is the hallmark of a superconductor; it arises from the purely inductive motion of the superfluid in the electromagnetic THz field. The results were compared with calculations with Mattis-Bardeen theory for BCS superconductors with an isotropic s-wave gap,95 shown as lines in Figures 4.11(b) and (c). This theory is valid in the so-called “dirty limit,” which occurs when the superconducting gap 2∆0 is much smaller than the normal state Drude width 1/τ. In this case, absorption sets in for frequencies above the superconducting gap 2∆, in which elastic scattering with rate 1/τ enables momentum conservation during THz absorption. The Mattis-Bardeen theory faithfully represents both real and imaginary parts of the experimental data. The gap in the real part reflects that, at the lowest temperatures, Cooper pair breaking is only possible for photon energies above 2∆0. At higher temperatures, the gap value decreases, and thermally excited quasiparticles exhibit an additional Drude-like response which results in the conductivity σ1(ω) even below
7525_C004.indd 138
11/15/07 11:08:54 AM
139
Time-Resolved Terahertz Studies of Carrier Dynamics
the gap. The temperature dependence of the superfluid response in σ2, which vanishes at TC = 30.5 K, is equally well reproduced.114 However, this overall agreement is possible only when an artificially small gap value of 2∆0 = 5 meV is assumed in the calculations. This value is almost a factor of two smaller than the ratio expected from the known TC in weak-coupling BCS theory, which predicts 2∆0 = 3.5 k B TC ≈ 9 meV. This persistently small gap size is a fundamental property of MgB2, which is also seen in numerous other experiments. In contrast to surface sensitive measurements, however, the THz probe penetrates through the bulk of the film and thus confirms the general presence of the small gap. The small gap value is explained by the existence of two superconducting gaps, of which the smaller one dominates the optical conductivity.117–119 First-principle band structure calculations confirm this novel physics and indicate that the dominant hole carriers in Boron p orbitals are split into two distinct sets of bands with quasi–two-dimensional and three-dimensional character. The coupling between these bands leads to MgB2’s novel superconducting state with two gaps but a single TC. In contrast to conventional narrow-gap superconductors such as MgB2, the THz electrodynamics of high-TC cuprates is quite different.1,106 Most notably, the superconducting gap has a d-wave symmetry and peaks around 30 THz, such that the typical BCS gap structure in σ1(ω) (Figure 4.11) is not observed in the 1- to 3-THz range. However, as with the BCS superconductors, a strong 1/ω dependence from the inductive condensate response is quite prominent in σ2(ω) below TC. A model that describes the electrodynamics of superconductors at frequencies far below the gap is the two-fluid model. It is useful to approximate the responses of high-TC cuprates in the range up to ≈3 THz. The two fluids in this model refer to thermally excited quasiparticles and the superconducting condensate. With decreasing temperature, more quasiparticles join the condensate. Thus the quasiparticle density nN(T) and the condensate density nSC (T) are temperature dependent. The sum of quasiparticle and condensate densities is constant with temperature: nN(T) + nSC (T) = n where n is the normal state carrier density above TC. This can also be written as X N(T) + XSC (T) = 1 where X N(T) ≡ nN(T)/n is the quasiparticle fraction and XSC (T) ≡ nSC (T)/n is the condensate fraction. The conductivity for the two-fluid model is given as 1 nN (T )e 2 n (T )e 2 + SC 1 / τ(T ) - iw m m
i pd(w ) + w
(4.7a)
ε 0 w 2p 1 i X N (T ) + pd(w ) + XSC (T ). 2 1 / τ(T ) - iw m 0 l L (0) w
(4.7b)
s(w ) =
=
The first term is just the Drude response with a temperature-dependent carrier density and scattering time. The second term describes the condensate response with the first term in brackets being a δ-function at zero frequency that describes the infinite DC conductivity of the superconducting condensate. The second term in brackets is a purely imaginary inductive response (obtained by letting τ → ∞ in the Drude model). We can thus see that, on condensation of quasiparticles into the superfluid, spectral weight is transferred from the Drude peak to the zero frequency
7525_C004.indd 139
11/15/07 11:08:58 AM
140
Terahertz Spectroscopy: Principles and Applications
superconducting peak. In Equation 4.7b, the condensate portion is rewritten in terms of the London penetration depth l 2L ( 0 ) =
m m 0 ne 2
(4.8)
which describes how far a DC magnetic field penetrates into the superconductor at zero temperature. These equations highlight an important aspect about the electrodynamics of superconductors; from a simultaneous measurement of σ1(ω) and σ2(ω), the quasiparticle and condensate fractions can be quantitatively determined. The temperature dependence of these fractions then can provide essential information about the superconducting state, to distinguish, for example, isotropic s-wave from anisotropic d-wave gap symmetries.106 Figure 4.12 shows a calculation using the two-fluid model for various values of X N and XSC (keeping X N + XSC = 1). For the calculations, τ = 150 fs, n = 1019 cm-3, and m* = m 0 giving σDC = 104 Ω-1cm-1 for X N = 1. The real part σ1(ω) is shown as a solid line, the total σ2(ω) is plotted as a dashed line, and the Drude contribution to σ2(ω) is plotted as a dotted line. A pure Drude response results for XSC = 0, see Figure 4.12(a). With XSC = 0.2, a clear 1/ω dependence is evident, although the relative Drude contribution to σ2(ω) is still quite large but becomes much smaller at XSC = 0.4. Finally, for XSC = 1 as shown in Figure 4.12(d), the response at THz frequencies entirely arises from the superconducting condensate. 2
σ/104 (Ω cm)−1
1 (a) Xn = 1, Xsc = 0
1
0.5
0.5 0
0
1
2
3
2 σ/104(Ω cm)−1
(b) Xn = 0.8, Xsc = 0.2
1.5
0
1
2
3
6 (c) Xn = 0.6, Xsc = 0.4
1.5
(d) Xn = 0, Xsc = 1 4
1
2
0.5 0
0
0
1
2
Frequency (THz)
3
0
0
1
2
3
Frequency (THz)
Figure 4.12 Model calculation using the two-fluid model for different values of the quasiparticle and condensate carrier fractions.
7525_C004.indd 140
11/15/07 11:09:02 AM
141
4
0.4 0
2 0
0.4
0.8
0.4
60 K 0.4
0.3
τ = 175 fs
1.2
1.6
0
95 K
0 0.2
2
0.6
τ = 51 fs 1 0.4 1.6 Freq (THz)
1
1.4
Frequency (THz)
Frequency (THz)
(a)
(b)
0.8
Scattering Time (fs)
Carrier Fractions
0.4
0.1 0.8
Xn
0.6 0.4 Xsc
0.2 20
0.2
1 1.6 Freq (THz)
1
0
0.8
σ1(ω)/104
6
σ1(ω)/104
σ2(ω)/104 (Ω cm)–1
Time-Resolved Terahertz Studies of Carrier Dynamics
40
60
80
1.8
350 250 150 50 0
0
50
100
150
200
Temp (K)
Temp (K)
(c)
(d)
250
Figure 4.13 THz-TDS measurements on YBa2Cu3O7 with two-fluid model fits.
Of course, this idealized situation is not practically realized, though as Figure 4.13 reveals, it provides a good starting point. Specifically, Figure 4.13 shows the results of THz-TDS measurements on a nearly optimally doped film of YBa2Cu3O7 (TC = 89 K) epitaxially grown on <100> MgO using pulsed laser deposition. Figure 4.13(a) shows σ2(ω) at T = 60 K, whereas Figure 4.13(b) shows σ2(ω) at 95 K. The insets show the corresponding real part σ1(ω). The thick solid lines are the experimental data and the dashed lines are fits using the two-fluid model. In Figure 4.13(a), the Drude contribution to σ2(ω) is plotted as a thin solid line with the condensate fraction plotted as a thin dotted line. The two-fluid model provides a reasonable fit to the data. In Figure 4.13(c), X N(T) and XSC (T) are shown as extracted from fits to the experimental data. The relation X N(T) + XSC (T) = 1 is seen to be accurate to within 10%. At the lowest temperature measured, X N(T) = 0.1, which is still a substantial quasiparticle fraction. In Figure 4.13(d), τ is plotted as a function of temperature. Below TC, there is a dramatic increase in the scattering time until ~50 K, where it saturates at 400 fs because of impurity scattering. This increase in τ results in a substantial narrowing of the Drude peak (see inset to Figure 4.13(a)). However, in even the best films, τ is still much shorter when compared with the highest quality single crystals where τ is so long that the Drude peak lies at microwaves frequencies.120
7525_C004.indd 141
11/15/07 11:09:05 AM
142
Terahertz Spectroscopy: Principles and Applications
Time domain THz spectroscopy was also used to study the conductivity in another important cuprate, Bi2Sr2CaCu2O8+d (Bi‑2212). In this material, about 30% of the spectral weight resides in an additional component that follows the temperature dependence of the superfluid but exhibits a finite scattering width 1/τ.121 This has been associated with static fluctuations of the superfluid due to real-space electronic inhomogeneity in Bi-2212 (that can be described as a disordered condensate response). Furthermore, THz-TDS experiments can be carried out on underdoped cuprates, which are known to exhibit a puzzling “pseudogap” phenomenon that appears in numerous spectroscopies and persists to temperatures well above TC. Among various explanations, the pseudogap has been ascribed to a transient phase coherence from short-lived remnants of the superfluid above TC. Here, THz-TDS experiments on underdoped Bi-2212 films have revealed that while such coherence indeed persists above TC, it cannot be the main source of the pseudogap because it vanishes well below the pseudogap temperature.122 Despite the subtleties of the cuprate properties, the two-fluid model (Equation 4.7 and Figure 4.12) is still a reasonable starting point for understanding their THz response well below the gap, and accordingly for insight into the nonequilibrium dynamics. Anticipating the dynamic experiments to be described later, the model suggests how we can fruitfully apply optical pump THz probe spectroscopy to superconductors. A short near-IR pulse breaks Cooper pairs, thereby reducing the condensate fraction and increasing the quasiparticle fraction. Subsequently, the excess photoexcited quasiparticles will recombine to the condensate. This process can be monitored in exquisite detail using THz pulses, allowing for the simultaneous measurement of the dynamical evolution of quasiparticle and condensate densities (i.e., of their time-dependent changes ∆nN(t) and ∆nSC (t)).
4.3.3 Quasiparticle Dynamics in Conventional Superconductors The basic properties of MgB2 and the electrodynamic response as measured using THz-TDS have been discussed previously. In the following, we describe the results of measurements using optical pump THz probe spectroscopy on 100-nm films of MgB2 deposited on sapphire (TC = 34 K).123,124 In these experiments, 100-fs pulses with a center wavelength of 800 nm were employed to photoexcite the sample at fluences sufficiently low (0.1–5 µJ/cm2) such that the condensate was perturbed without driving the sample above TC. In Figure 4.14(a), the imaginary conductivity is plotted as a function of frequency at various delays with respect to the photoexcitation pulse. The initial temperature is 7 K and the excitation fluence is moderately high at 3 µJ/cm2. At ∆t = –5 ps, the 1/ω condensate response dominates. At 3 ps, the condensate response is dramatically reduced and even more so at 10 ps. By 300 ps, the condensate has still not fully recovered. Interestingly, it takes some time (≈10 ps) for the pair-breaking (i.e., reduction in condensate density) to finish. This is shown more clearly in Figure 4.14(b), where the dynamics of σ1(ω) and σ2(ω) at 0.8 THz are plotted as a function of time. As the condensate response decreases, a corresponding increase in the quasiparticle density is observed in σ1(ω). This is followed by a much longer recovery time as quasiparticles rejoin the condensate. The condensate recovery time is plotted in Figure 4.14(c) and shows a pronounced temperature dependence peaking near TC.
7525_C004.indd 142
11/15/07 11:09:06 AM
143
Time-Resolved Terahertz Studies of Carrier Dynamics
σ2(ω)/104 (Ω cm)–1
6 σ1
4 4
–5 ps
3
300 ps 2
σ2
2
3 ps 10 ps
1
1.0 1.5 Frequency (THz)
0
10 100 200 Time (ps)
(a)
(b) 5
τ(ns)
∆σ (a.u.)
0.8
0.4
4 1.51.2 1 0.6
1
2
0.4
0.1 0
30 10 20 Temperature (K)
1
10 Time (ps)
50
(d)
(c)
Figure 4.14 Optical pump THz probe spectroscopy of MgB2. (a) Dynamics of the imaginary conductivity related to the condensate density at T = 7 K. (b) Conductivity dynamics at 0.8 THz, for T = 7 K. (c) Condensate recovery time. (d) Initial change in the conductivity related to pair-breaking dynamics at various fluences (in µJ/cm2).
Finally, in Figure 4.14(d), the pair breaking dynamics are plotted for various fluences. With increasing fluence, the pair breaking time decreases. The observed pair breaking and pair recovery dynamics in MgB2 can be understood using the phenomenological Rothwarf-Taylor model.98 This model consists of two coupled rate equations describing the temporal evolution of the density of excess quasiparticles and phonons injected into a superconductor. The Rothwarf-Taylor equations are written as
dn = βN - Rn 2 - 2 RnnT dt dN 1 ( N - N0 ) = [ Rn 2 - βN ] . τP dt 2
(4.9a) (4.9b)
Here, n is the excess quasiparticle density, nT is the thermal quasiparticle density, N is the excess density of phonons with energies greater than 2∆, R is the bare
7525_C004.indd 143
11/15/07 11:09:12 AM
144
Terahertz Spectroscopy: Principles and Applications
quasiparticle recombination rate, β is the rate of pair breaking by (>2∆) phonons, and τP describes the relaxation time of the phonons either by anharmonic decay to phonons with energies <2∆ or through phonon escape from the sample (e.g., into the substrate). As Equation 4.9a reveals, in the limit of small nT, the recombination of quasiparticles is a bimolecular process (hence the n2 term) requiring, as expected, two quasiparticles to form one Cooper pair. However, the direct determination of R is made difficult as it can be masked by excess 2∆ phonons breaking additional Cooper pairs (e.g., the βN term). Thus, in many measurements, the phonon decay τp is measured and has been termed the phonon bottleneck. The phonon bottleneck is clearly observed in the condensate recovery dynamics of MgB2 and Pb superconductors.125 In MgB2 the recovery time is largely independent of fluence (Figure 4.14(c)) in contrast to bimolecular recombination kinetics. In MgB2, Pb, and likely all conventional superconductors, the condensate recovery is governed by the decay of acoustic phonons which, as described previously, could be due either to anharmonic decay or phonon escape from the probe volume. In MgB2, no change in τP was observed as a function of film thickness, indicating that phonon escape is not important and the condensate recovery is therefore determined by anharmonic decay processes. This assignment of the recovery is further supported by the observed temperature dependence near TC showing that τp ∝ 1/∆(T). This 1/∆(T) dependence occurs because the superconducting gap decreases in magnitude with increasing temperature. This results, for the same photoexcitation fluence, in a larger density of phonons with energies in excess of 2∆ yielding an increased condensate recovery time. The early time pair breaking dynamics in Figure 4.14(d) are somewhat surprising, because after excitation with a 100-fs pulse, the reduction in condensate density continues for ≈10 ps. This is in contrast with Pb, in which the pair breaking dynamics are complete in ≈1 ps.126 An understanding of this delayed pair breaking dynamics can be obtained from the Rothwarf-Taylor equations. In the limit of small nT and neglecting the term with τp (which is reasonable since the condensate recovery timescale is much longer than the initial pair-breaking dynamics), it can be shown that n(t ) =
β 1 1 1 1 - + R 4 2 τ τ 1 - K exp ( -tβ / τ )
τ 4 Rn0 + 1 - 1 2 β K= ; τ 4 Rn0 + 1 + 1 2 β
1 = τ
(4.10a)
1 2R + ( n0 + 2 N 0 ) 4 β
(4.10b)
where n 0 and N0 are, respectively, the initial excess quasiparticle and phonon densities and the time scale of the initial dynamics is given by τ.123 Of particular importance is the dimensionless parameter K, which describes three distinct regimes for the pair breaking dynamics, as manifested in the last term of Equation 4.10(a). For K = 0, the quasiparticles and phonons are in quasi-equilibrium at an elevated temperature.
7525_C004.indd 144
11/15/07 11:09:15 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
145
For this case the initial pair-breaking dynamics would show a step-like dependence at t = 0. The regime 0 < K ≤ 1 corresponds to the situation when the density of excess quasiparticles is larger than the quasi-equilibrium (K = 0) situation, whereas –1 ≤ K < 0 corresponds to the situation in which the excess density of >2∆ phonons is greater than for K = 0. The dynamic signature for this regime is a pronounced rise time and appears to explain the pair breaking dynamics in MgB2 in Figure 4.14(d). That is, a significant fraction of the energy in the photoexcited quasiparticle distribution is initially transferred to high-energy phonons that subsequently break additional Cooper pairs before condensate recovery. This contrasts with a scenario in which the photoexcited quasiparticles reach quasi-equilibrium through direct pair breaking in an avalanche-like process not involving phonons. Fits to the rise time dynamics at various fluences (solid lines in Figure 4.14(d)) using Equations 4.10a and 4.10b permitted a determination of the phonon pair breaking and bare quasiparticle recombination rates,123 yielding β–1 = 15 ± 2 ps and R = 100 ± 30 unit cell/ps, respectively.
4.3.4 Quasiparticle Dynamics in High-TC Superconductors Knowledge of quasiparticle interactions is particularly relevant for the high-TC cuprate superconductors, where the mechanism for charge pairing at temperatures up to ≈100 K remains unresolved.127 These materials show a complex phase diagram as a function of chemical doping; with increased density of hole carriers in the Cu2O planes they transition from an insulating antiferromagnetic state, via a non-Fermi liquid state that shows superconductivity at relatively small TC (“underdoped”) to the state with highest TC (“optimally doped”). As the doping is further increased, the materials show Fermi liquid properties and a progressively smaller TC until they are no longer superconducting. The quest to understand the complex quasiparticle properties and interactions in cuprates has inspired numerous experiments that employ visible or near-IR fs pulses to observe optical reflectivity changes at E ≈ 1–2 eV probe energy.108,128–130 However, it should be understood that this energy scale far exceeds the fundamental excitations of a superconductor, such as the THz gap and collective quasiparticle and Cooper pair response discussed previously. Ultrafast THz studies of superconductors, in contrast, can provide a direct measure of quasiparticle and Cooper pair dynamics, but have remained scarce. In the following section, we discuss these first THz studies of high-TC superconductor ultrafast dynamics. From a simple extrapolation of the dynamics on conventional superconductors one might expect similar dynamics on the high-TC cuprates. For example, near TC it was shown that for conventional superconductors the condensate recovery time is proportional to 1/∆(T). This suggests that the condensate recovery in the cuprates might follow a similar trend, albeit with a shorter lifetime given the larger gaps in these materials. Although such behavior is observed and there are similarities between these two classes of superconductors, there are also important differences in the nonequilibrium dynamics that likely originate from their vastly different microscopic properties. The major microscopic differences are that in the cuprates (1) superconductivity is obtained through chemical doping of Mott-Hubbard insulators, (2) superconductivity is thought to occur in two-dimensional CuO2 planes, (3) the superconducting order parameter has d-wave symmetry resulting in nodes in the superconducting gap (along kX = kY), and (4) there is the distinct possibility
7525_C004.indd 145
11/15/07 11:09:16 AM
146
Terahertz Spectroscopy: Principles and Applications
that the boson mediating pairing is not a phonon but some other excitation such as antiferromagnetic spin fluctuations. The hope is that optical pump THz probe and time-resolved mid-IR studies can provide insight into the properties of the cuprates through, for example, extracting the quasiparticle recombination rate or unmasking other interactions that are hidden in various time-integrated spectroscopies. We will briefly describe the first optical pump THz probe experiments that were performed on near-optimally doped and underdoped samples of yttrium– barium–copper oxide.131,132 The measurements were made on the same epitaxial films in Figure 4.13 and others grown under similar conditions including YBa2Cu3O7-d with TC = 89 K (50 K) for δ = 0 (0.5) and Y0.7Pr0.3Ba2Cu3O7 with TC = 0.5. The Pr compounds provide an alternate approach to achieve underdoping which is easier than controlling the oxygen stoichiometry. Figure 4.15(a) shows σ2(ω) as a function of frequency at various delays after photoexcitation for YBa2Cu3O7 at 60 K, whereas Figure 4.15(b) shows the dynamics for Y0.7Pr0.3Ba2Cu3O7 at 25 K. In both cases, there is a rapid decrease in the condensate fraction followed by a fast picosecond recovery. The condensate recovery is nearly complete by 10 ps, in dramatic contrast to conventional superconductors. The extracted lifetimes of the conductivity dynamics, and thus the condensate recovery time, are shown in Figure 4.15(c) for all of the samples investigated. In the
σim/104 (Ω cm)–1
YBa2Cu3O7-δ 6
Unpumped
0
60 K
2.5
Unpumped
2
10 ps
4 2
Y0.7Pr0.3Ba2Cu3O7 25 K
10 ps
1.5 1
1 ps 0.5
1
1 ps
0.5
2 ps 1.5
2
0
0.4
0.8
2 ps 1.2
1.6
Frequency (THz)
Frequency (THz)
(a)
(b)
5 τσ(ps)
4 3 95 K
2 1
0
10
20
30
40 50 T(K)
60
70
80
90
(c)
Figure 4.15 Condensate dynamics on (a) YBa2Cu3O7 and (b) Y0.7Pr0.3Ba2Cu3O7. (c) Summary of lifetimes measured on near-optimally doped and underdoped films—the lines are to guide the eye. Triangles: YBa2Cu3O6.5, diamonds: Y0.7Pr0.3Ba2Cu3O7. Closed and open circles: two different YBa2Cu3O7 films taken at different fluences.
7525_C004.indd 146
11/15/07 11:09:20 AM
147
Time-Resolved Terahertz Studies of Carrier Dynamics
1.3 ps
0 10 ps 35 ps 50 ps 4
6 8 10 4 6 8 10 Photon Energy (meV)
0
–2000
(c)
(d)
1
0 –2 –4
0.1
1/∆σ2 (10–3 Ω cm)
1000
(b) t = –1.2 ps
–∆σ2(1000 Ω–1 cm–1)
(a)
∆σ2(ω)(Ω–1 cm–1)
∆σ1 (ω)(Ω–1 cm–1)
optimally doped films (closed and open circles), the condensate recovery is approximately 1.7 ps and increases near TC, consistent with a decrease in the superconducting gap. Above TC at 95 K, the lifetime has decreased to 2 ps and is likely a measure of electron–phonon equilibration in the normal state. Furthermore, the lifetime is independent of fluence indicative of the absence of bimolecular kinetics although this was not pursued in detail in this work.131,132 In contrast, for the underdoped films (triangles and diamonds in Figure 4.15(c)), the lifetime was constant at ≈3 ps even above TC. The constant lifetime as a function of temperature is suggestive of a pseudogap. These results revealed that it is possible to sensitively probe the condensate dynamics in the cuprates using optical pump THz probe spectroscopy. A comprehensive study of the transient picosecond THz conductivity changes after ultrafast optical excitation in a different superconductor, Bi2Sr2CaCu2O8+d (Bi‑2212), has recently been reported.133 The pump-induced change ∆σ(ω) of the CuO2 plane THz conductivity was measured in 62-nm thick optimally doped Bi-2212 films with a transition temperature TC ≈ 88 K. As in YBCO, in the superconducting state a 1/ω component dominates the imaginary part of conductivity σ2(ω) at low frequencies, which provides a direct measure of the condensate density. Figures 4.16(a) and (b) show the conductivity change observed directly after photoexcitation. The imaginary part displays a strong decrease, ∆σ2 < 0, because of the depletion of the condensate via interactions with the photoexcited carriers. This superfluid spectral weight is transferred to the quasiparticles, as shown by the broad increase of σ1. The photo-induced conductivity changes recover on a ps timescale. The changes are well reproduced with the two-fluid model (solid lines in Figure 4.16(a) and (b)) where the total spectral weight is conserved, or (e2/m*) ∆nSC = −(e2/m*) ∆nN.
–6 0 20 40 60 0 20 40 60 Time Delay t (ps)
Figure 4.16 Dynamics of Cooper pair formation observed via optical pump THz probe spectroscopy of the high-TC superconductor Bi-2212. The results are for T = 6 K lattice temperature and 0.7-µJ/cm2 fluence of the near-infrared excitation pulses. (a) and (b) Induced changes of the real and imaginary parts of the THz conductivity (circles) for different pump– probe delays t. Thick lines: two-fluid model. (c) Conductivity dynamics around 5.5-meV probe energy (symbols) plotted on a logarithmic scale. (d) The same data as in panel (c), but plotted as 1/∆σ2. The linear decay on this reciprocal scale reveals a bimolecular kinetics of condensate recovery. Solid lines are guides to the eye. (Reprinted with permission. Copyright 2005 by the American Physical Society.)
7525_C004.indd 147
11/15/07 11:09:23 AM
148
Terahertz Spectroscopy: Principles and Applications
A central result of the Bi-2212 experiments relates to the temporal shape of the relaxation dynamics. Figure 4.16(c) displays the dynamics of the superfluid density in ∆σ2. Clearly, the decay is nonexponential, which is seen by comparison with the single exponential model curve (solid line). Figure 4.16(d) shows the same data on a “reciprocal” scale (i.e., it is plotted 1/∆σ2 versus linear delay time). The decay in Figure 4.16(d) shows a strikingly simple linear time dependence
1 1 = + r ⋅ t. Ds 2 (t ) Ds 2 ( 0 )
(4.11)
This linear time dependence plotted on a reciprocal scale is a benchmark for bimolecular kinetics. By taking the time derivative of Equation 4.11, and taking into account the proportionality ∆σ2 ∝ ∆nSC ∝ ∆nN (confirmed by the two-fluid fits at each time delay) we obtain directly d/dt ∆nN = − R (∆nN)2. A natural explanation of this bimolecular kinetics is the pairwise interaction of quasiparticles as they recombine into Cooper pairs. Further evidence for the bimolecular recombination picture is obtained from the very strong density and temperature dependence, which are fully explained by the bimolecular rate equation, as discussed elsewhere.133 It has been conjectured that the origin of the fast bimolecular decays in Bi-2212 may be linked to quasiparticle recombination from the antinodes of the anisotropic d-wave superconducting gap through emission of short-lived high-energy phonons or spin waves.133 Unlike YBCO, scanning probe microscopies have shown that Bi-2212 exhibits a nanoscale electronic inhomogeneity,134 which may further relax momentum restrictions for quasiparticle scattering. This may also explain the differences in the dynamics between YBCO and Bi-2212. Although these studies on cuprates probed changes in the collective charge motion of quasiparticles and Cooper pairs, they did not probe the superconducting gap. For high-TC superconductors, signatures of this gap occur at higher frequencies around 10 to 50 THz (≈40 to 200 meV). They are of fundamental significance. Among the longest-standing puzzles of the cuprates is the pseudogap, a depression in the electronic density of states.17,135 It mimics the superconducting gap in energy but appears already at temperatures T* much higher than TC. It is widely believed that understanding the correlations that lead to the emergence of this pseudogap will also help clarify the mechanism of superconductivity in the cuprates. Because the pseudogap and superconducting gap are similar in energy, it is difficult to separate them in time-integrated linear spectra. Next we discuss a first ultrafast study that probes changes in the gap region, enabling separation of components along the temporal degree of freedom.136 Optimally doped and underdoped thin films of YBCO (with TC = 88 and 68 K, respectively) were excited at 1.6 eV with a 2-MHz repetition rate cavity-dumped Ti:sapphire laser. Terahertz probe pulses spanning the ultrabroadband range from ≈14 to 43 THz with 150-fs pulse duration were generated in a novel GaSe-based technique25 and were employed to detect transient reflectivity changes around the YBCO gap. As shown in Figure 4.17(a), optimally doped YBCO at low temperatures exhibits a subpicosecond reflectivity increase around 22 THz probe frequency (90 meV), followed by a decay on an approximate 5-ps timescale. The amplitude ∆R/R of this
7525_C004.indd 148
11/15/07 11:09:25 AM
149
Time-Resolved Terahertz Studies of Carrier Dynamics
T= 14 K
2
–2
1 71 K
0
94 K 0
2 4 Time Delay (ps) (a)
6
20
300 fs
160 fs
5 ps
5 ps
30 ps
30 ps
30 (b)
20 40 Frequency (THz)
(d)
1 ∆R/R0 (×10–3)
0
30
–4
40
–6
(c) (e)
T = 100 K
1
Slow
0 50 K –1
Fast
14 K 0
2 4 Time Delay (ps) (d)
∆R/R0 (×10–3)
2
Amplitude (norm.)
∆R/R0 (×10–3)
3
0 6
0
50
100 Temperature (K) (e)
150
Figure 4.17 (a) Transient change of the reflectivity at 21.8 THz in optimally doped YBCO after near-infrared excitation, for different lattice temperatures T as indicated. (b) and (c) Spectra of the reflectivity change ∆R/R0 at different pump–probe time delays for (b) T = 14 K and (c) T = 94 K. (d) Dynamics in underdoped YBCO probed at 35 THz, for different temperatures. (e) Amplitudes of the fast and slow components (symbols) and the sum total (solid line) of the dynamics in underdoped YBCO.
change slowly decreases as the sample temperature is raised, whereas above TC, it changes into a very fast relaxation dynamics with opposite sign. This difference between the behavior below and above TC is further corroborated by the spectral response shown in Figures 4.17(b) and (c). Below TC, the induced reflectivity change in Figure 4.17(b) shows a strong oscillatory structure. It happens to follow exactly the spectral changes in the stationary reflectivity as the sample temperature is lowered from above TC into the superconducting state.137,138 Hence, below TC the experiment directly shows the subpicosecond reduction of the superconducting gap followed by its reformation on a 5-ps time scale, in agreement with the time scales of condensate depletion and reformation observed in the 1- to 3-THz spectral range.131,133 In contrast, the much faster dynamics and featureless spectra above TC (Figure 4.17(c)) can be attributed to the cooling of a hot carrier distribution analogous to dynamics in metals.139 The mid-IR dynamics in underdoped YBCO show a markedly different dynamics. As seen in Figure 4.17(d) for 35-THz probe frequency, the reflectivity change
7525_C004.indd 149
11/15/07 11:09:27 AM
150
Terahertz Spectroscopy: Principles and Applications
below TC = 68 K cannot be explained by a single decaying component. Rather, it is described by two components: a “fast” reflectivity increase and decay, and a slower ≈5-ps constituent that follows the superconducting gap dynamics of optimally doped YBCO. A more detailed analysis across all probe frequencies showed that both components show a similar (but not identical) spectral shape that corresponds to changes of a conductivity gap around 100 meV. It also provides the temperature dependence of the amplitudes (Figure 4.17(e)). The “slow” component vanishes at TC, as in the optimally doped sample—it is a signature of the superconducting gap dynamics because of breakup and reformation of Cooper pairs. In contrast, the fast ≈700-fs component persists up to the pseudogap temperature T* > TC (T* ≈ 160 K in this sample), and results from ultrafast excitation of a second kind of correlated carrier that lies at the origin of the pseudogap phenomenon. The latter may be due to preformed pairs or antiferromagnetic correlations.135 Thus the femtosecond study provides a separation of different components of the ≈30 THz conductivity gap, which remain hidden in linear spectra. The temperature dependence of the transient signal amplitudes also closely follows the strength of an important, 41-meV antiferromagnetic resonance in cuprates, which supports theories in which spin fluctuations couple strongly to the carriers.136 The experiments discussed show the detailed insight into the dynamics of superconductors obtained by employing THz pulses as probes of the fundamental charge excitations. They motivate further work on a larger range of materials to elucidate the differences or similarities in the pseudogap correlations or quasiparticle recombination kinetics. Moreover, almost all previous time-resolved studies of superconductors have employed photoexcitation in the 1- to 2-eV range. This leads to a cascade of scattering processes as quasiparticles relax to the low-energy states, resulting in a fairly indirect and uncontrolled way to break Cooper pairs. We can envision that in the future resonant excitation of superconductors with intense THz pulses at the gap energy 2∆0 will be possible, leading to direct control of (and consequently even more detailed insight into) the nonequilibrium state of superconductors.
4.4 Half-Metallic Metals: Manganites and Pyrochlores 4.4.1 Overview Manganite perovskites such as R1-xDxMnO3 (where R = La, Nd and D = Ca, Sr) and related compounds are similar to the cuprates in that their parent materials (e.g., LaMnO3) are Mott-Hubbard insulators. As a function of doping, fascinating states occur ranging from charge-ordered insulator to ferromagnetic metal phases. The most studied materials of this class during the past decade are the optimally doped manganites around x ≈ 0.3, which includes La0.7Ca0.3MnO3 and La0.7Sr0.3MnO3. Here, “optimal” refers to the maximum ferromagnetic Curie temperature TC. Above TC, these materials are paramagnetic semiconductors, whereas below TC, they transition into ferromagnetic metals. In the vicinity of TC, an applied magnetic field yields a dramatic decrease in the resistivity. This large negative magnetoresistance has resulted in these materials being termed colossal magnetoresistive (CMR) manganites. They are also often called half-metallic manganites referring to the complete spin polarization that occurs below TC. Several excellent reviews of CMR materials
7525_C004.indd 150
11/15/07 11:09:29 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
151
are available.4,5,7,9,140 Recent research has focused on the structural and electronic properties away from optimal doping, with the nature and origin of intrinsic electronic inhomogeneities receiving considerable attention.5 Although the intense interest in manganites during the past decade141 derives from advances in cuprate superconductivity, these materials have been investigated since their discovery in the 1950s. This initial work led to fundamental theoretical insights related to double exchange and experimental explorations such as neutron scattering studies of their detailed magnetic structure.142–146 In the manganites, the structural units of interest are the MnO6 octahedra. The octahedral symmetry breaks the five-fold degeneracy of the Mn d-orbitals resulting in localized t2g spins (S = 3/2) and higher lying eg spins. It is in this eg‑derived band that transport occurs. Additionally, strong Hund’s rule coupling leads to slaving of the eg to the t2g spins, an essential ingredient to the so-called double exchange. In the double exchange model, electron transport between adjacent Mn ions via an intervening oxygen orbital is enhanced if the core spins on adjacent sites are parallel. However, it is now realized that the double exchange model alone cannot account for CMR behavior because the magnitude of the resistivity in the paramagnetic phase is larger than spin scattering predictions.147,148 Coherent lattice effects such as the Jahn-Teller distortion of the MnO6 octahedron also affect the charge transport. The simple picture is that in the paramagnetic phase lattice distortions can follow the carriers from site to site because disorder (of the t2g spins) reduces the carrier kinetic energy, resulting in polaronic transport. Ferromagnetic ordering increases the carrier kinetic energy. Hopping from site to site becomes too rapid for the lattice distortions to follow the carriers, resulting in a metallic state (though polaronic signatures persist below TC). Although the ultimate origin of CMR in the manganites has not been established, it is clear that the spins and polaronic behavior are basic ingredients to consider. In the quest to more fully understand the origin of CMR, many other materials have been synthesized and characterized.149 A particularly important class of materials in this regard are the pyrochlores such as Tl2Mn2O7, which also display a pronounced negative magnetoresistance.150,151 In Tl2Mn2O7, the transition temperature is TC = 120 K. Pyrochlores at first appear quite similar to perovskite manganites: both exhibit CMR, and MnO6 octahedrons are equally important structural subunits. However, experimental and theoretical studies have highlighted important differences. In particular, in pyrochlores double exchange and Jahn-Teller effects are negligible because of the low carrier density and the absence of the Jahn-Teller Mn3+ ion. In addition, separate subsystems are responsible for ferromagnetic ordering (Mn 3d electrons, t2g with S = 3/2 as in manganites) and conduction properties (Tl 6s electrons). The ferromagnetic ordering of the Mn4+ sublattice likely occurs through frustrated superexchange between Mn on adjacent sites. Below TC, indirect exchange between the Mn and Tl orbitals causes a band of primarily Tl 6s character to shift below the Fermi level. It thus appears that the microscopic origin of CMR in pyrochlores and manganites is quite different, though the possibility remains that CMR in both materials derives from mesoscopic effects related to intrinsic electronic inhomogeneities. Below, we briefly discuss time-integrated infrared spectra of La0.7Ca0.3MnO3 and Tl2Mn2O7, followed by a description of time-resolved studies.152–155 These THz studies provide insight into their fundamental
7525_C004.indd 151
11/15/07 11:09:30 AM
152
Terahertz Spectroscopy: Principles and Applications
properties and highlight important differences between these half-metallic correlated materials.
4.4.2 Optical Conductivity and Spectral Weight Transfer
σreal/103 (Ω cm)–1
For the cuprates, we discussed how, on entering the superconducting state, spectral weight transfers from the Drude-like response to the condensate response represented as a Dirac delta function at zero frequency. In the manganites, spectral weight transfer also occurs as a function of temperature.155 However, for these materials the spectral weight transfer occurs from higher energies (~1 eV) to a coherent Drude-like response with the crossover from paramagnetic semiconductor to ferromagnetic metal. This spectral weight transfer is intimately related to the CMR effect in DC conductivity measurements and involves the spin and lattice degrees of freedom. Figure 4.18 shows the temperature dependence of the optical conductivity from 0.2 to 5 eV as a function of temperature for La0.7Ca0.3MnO3 (TC ~ 260 K).155 This clearly shows spectral weight transfer with decreasing temperature and the development of a Drude peak centered at zero frequency. A detailed discussion of the various features of the optical conductivity has been presented.155 The broad feature at ~1.0 eV has been interpreted in terms of the photon-induced hopping of Jahn-Teller polarons. With decreasing temperature, it is this Jahn-Teller peak that partially evolves into a metallic response below TC. This is just as discussed previously, in that with increasing spin polarization the increased carrier kinetic energy is sufficient to overcome polaronic trapping. Further details regarding the higher energy peaks can be found elsewhere.155 In the pyrochlore Tl2Mn2O7 (TC = 120 K), there is also a strong transfer of spectral weight from higher to lower energies with decreasing temperature.153 However, in this material there is no high energy peak ascribable to polarons and the spectral weight transfer likely comes from higher energy (>2 eV) interband transitions consistent with the crossing of a single Tl 6s band as the ferromagnetic half-metallic state develops. Figure 4.19 shows the temperature dependence of the reflectivity for Tl2Mn2O7. At 295 and 160 K, the carrier density is very low such that the phonons
Mn3+
1.5
O eg
1.0
t2g
Mn4+ t
eg
10 K 100 K 125 K 150 K 200 K 225 K 250 K 300 K
t2g
0.5 La0.7Ca0.3MnO3 1
2
3
4
5
Photon Energy (eV)
Figure 4.18 Optical conductivity in La0.7Ca0.3MnO3 as a function of photon energy at various temperatures. The inset gives a schematic depiction of double exchange. (Reprinted with permission. Copyright 1998 by the American Physical Society.)
7525_C004.indd 152
11/15/07 11:09:33 AM
153
Reflectivity
Time-Resolved Terahertz Studies of Carrier Dynamics
0.8 0.6 0.4 0.2
40 K
0.8
160 K
0.6 0.4 0.2
0.8 0.6 0.4 0.2
110 K
0.8
295 K
0.6 0.4 0.2
0.01
0.1
1
0.01 Energy (eV)
0.1
1
Figure 4.19 Infrared reflectivity in Tl2Mn2O7 at various temperatures.
are clearly observable. At 110 K, the development of a Drude peak occurs and it is fully developed at 40 K (though the phonons are still not fully screened). Comparing the 40 K data with Figure 4.1(b), we can see that the response is entirely consistent with Drude-like behavior including the dramatic decrease in the reflectivity at ωs which dips and then rises back up to a value consistent with ε∞. This behavior is quite different from that of the manganites, which are much more spectrally congested because of the distinct polaronic response. In Tl2Mn2O7, the carrier density below TC increases as the square of the magnetization to a maximum value of n ≈ 1019 cm-3, about two orders of magnitude smaller than in manganites.
4.4.3 Dynamic Spectral Weight Transfer in Manganites Figure 4.20 shows the results of THz-TDS and optical pump THz probe measurements on a 100-nm thick film of La0.7Ca0.3MnO3 grown on LaAlO3.152,156 In Figure 4.20(a), the real conductivity is plotted as a function of frequency at various temperatures. These conductivity measurements are in the regime ωτ << 1 as indicated by the flat frequency response. A large increase in the conductivity results with decreasing temperature, up to a value of ≈6 × 103 Ω-1cm-1 at T = 4 K, which is similar to poor metals. Figure 4.20(b) shows the temperature dependence at 0.7 THz. The solid line is a fit with σ(T) = σ0 exp(M(T)/M0), where M(T) ∝ (1-T/TC)b is the magnetization and β = 0.33. The results are in good agreement with DC resistivity measurements. The spin ordering thus clearly plays a role in determining the magnitude of the conductivity. However, as we will see from the ultrafast measurements, thermally disordered phonons (i.e., not polarons) are also quite important. Figures 4.20(c) and (d) show the dynamic changes in conductivity following photoexcitation with 100-fs 1.55-eV pulses at T = 15 and 180 K, respectively.152,156 A two-component conductivity dynamics is observed after the creation of a nonthermal electron distribution. Relaxation of this hot quasiparticle distribution cools through phonon emission. This corresponds to the fast resolution-limited component in the data. The longer time scale is in turn related to the spin-lattice thermalization, in which spins eventually come into thermal equilibrium with the phonons. Between 15 and 180 K, there is a strong change in the relative amplitudes of these two
7525_C004.indd 153
11/15/07 11:09:35 AM
154
Terahertz Spectroscopy: Principles and Applications 6
La0.7Ca0.3MnO3
σr/103 (Ω cm)–1
5
4K
50 K
4
70 K
3
90 K
2
130 K 170 K 200 K 230 K
1 0
6
15 K
5 4 3
1.0
0.5
0
Frequency (THz) (a)
40 Time (ps) (c)
80
10 σr/103 (Ω cm)–1
1.0
180 K
0.9
1 La0.7Ca0.3MnO3 Tc = 250 K
0.1
0
100
0.8 200
0
50
Temperature (K)
Time (ps)
(b)
(d)
100
Figure 4.20 (a) and (b) Temperature-dependent real part of conductivity in La0.7Ca0.3MnO3 measured using THz-TDS. (c) and (d) Two-component decrease in the conductivity after photoexcitation.
components: the fast electron-phonon related decrease in the conductivity and that related to spin-lattice thermalization. At low temperature, the conductivity decrease is dominated by electron–phonon relaxation, whereas closer to TC, the spin-lattice thermalization component becomes more dominant. It is possible, using the timeintegrated and time-dependent data in Figure 4.20 (and more data at other temperatures), to extrapolate the conductivity in the TS -TL plane by expanding ln(σ(TS, TL)) in a power series and performing a least squares fit. TS is the spin temperature and TL is the lattice temperature. This fitting procedure has been accomplished for La0.7Ca0.3MnO3 to third order in TS and TL . The results are shown in Figure 4.21 as contours of constant ln(σ) in the TS -TL plane.152,156 Conventional measurements do not deviate from equilibrium as indicated by the white diagonal line in the figure. However, the optical pump THz probe experiment starting from a point on the equilibrium line allows for access to the portion of the TS -TL plane below the diagonal because the excited electrons preferentially couple to the phonons during the initial 2 ps. This optically induced change in the phonon temperature is shown by the solid black arrow. The magnitude of this change is given by z/CL where z is
7525_C004.indd 154
11/15/07 11:09:39 AM
155
Time-Resolved Terahertz Studies of Carrier Dynamics 1
: Spin-lattice equilibration slope = Cphonon/Cspin
: Initial Excitation α Elaser/Cphonon
Tspin/Tc
0.8
0.6
0.4 Eq
0.2
0
u
ili
a br
tio
n
Li
: ne
=
in
T sp
8.5
2
8 n
no
ho
Tp
7.5 7 6.5
1
6 5.5 5
0
0.2
0.4 0.6 Tphonon/Tc
0.8
1
Figure 4.21 Plot of the natural log of the conductivity in the phonon spin temperature plane. The white diagonal line denotes the equilibrium line (TS = TL) of conventional timeintegrated measurements. The white lines are contours of constant conductivity.
the absorbed laser energy and CL is the lattice specific heat. The sample then returns to the equilibrium line as shown by the dashed arrows with the slope CL/CS (where CS is the specific heat due to the spins). Depending on the initial temperature, z, and CL , S, the observed conductivity decrease can depend predominantly on changes in the spin temperature, the phonon temperature, or both. When the contours of constant conductivity are nearly perpendicular to the TL axis, the change in conductivity is dominated by the phonons. This is the case at low temperatures as shown in the Figure 4.21 (label 1). However, at higher temperatures near TC, the lines of conductivity are now nearly parallel to the TL axis, and thus the changes in conductivity are mostly related to changes in the spin temperature (label 2). In short, changes in conductivity at low temperatures are dominated by thermally disordered phonons, while spin fluctuations and the associated polaronic correlations dominate at higher temperatures.152,156
4.4.4 Carrier Stabilization in Tl2Mn2O7 through Spatial Inhomogeneity For the manganites, the dynamics result from energy transfer from the excited quasiparticle distribution to the lattice and spin degrees of freedom. Furthermore, the metallic-like carrier densities of approximately 1021 cm–3 means that, for moderate fluences, it is not possible to excite a large fractional change in the carrier density. The pyrochlore Tl2Mn2O7, however, has a much lower carrier density, making it possible to photoexcite a large fractional change in the carrier density. In fact, optical pumping at 1.55 eV photoexcites electrons from O 2p orbitals to the Tl 6s-derived band. Furthermore this occurs (below TC) preferentially in the minority spin band
7525_C004.indd 155
11/15/07 11:09:43 AM
156
Terahertz Spectroscopy: Principles and Applications
∆R/R × 100
(i.e., the carriers in the Tl 6s band have their spins oppositely oriented to the Mn t2g spins). Tl2Mn2O7 cannot be grown as a thin film and the synthesis of single crystals is accomplished using high pressure techniques.150 Thus optical conductivity (Figure 4.19) and time-resolved measurements are performed in reflection. To track the changes in the photoexcited carrier density, dynamic shifting of the plasma edge was measured at different wavelengths. In the following, results are presented for measurements at 5-µm wavelength. Figure 4.22(a) shows the photo-induced changes ∆R/R in the reflectivity as a function of time at various temperatures. At all temperatures, the traces show a rapid change in reflectivity at zero delay, followed by a fast relaxation with a timescale of a few picoseconds and a slower component with a 10- to 100-ps timescale. The negative ∆R/R is consistent with a photo-induced increase in the carrier density that causes a shift of the plasma edge to higher energies. The relatively fast ≈10-ps initial relaxation reduces the photoexcited carrier density. For T << TC, nearly all of the carriers follow this recombination pathway. However, near and above TC, a large offset appears in ∆R/R indicating the establishment of a long-lived carrier population.
0 –1 –2 –3 –4 0
0 50 K
–1
–1
–3 0 –1 –2 –3 –4
180 K
–2 –3
110 K
–2
0 100
300
500
295 K
0 100
300
500
Time (ps)
PI Carrier Density/1018 (cm–3)
(a) 12 10 8
1
6
2
4
50 ps 500 ps
2 0
3
0
50
100
150
200
250
300
Temperature (K) (b)
Figure 4.22 (a) Photo-induced reflectivity changes at 5 mm wavelength in Tl2Mn2O7 for various temperatures. (b) Experimentally determined photo-induced carrier densities at 50 and 500 ps.
7525_C004.indd 156
11/15/07 11:09:46 AM
157
Time-Resolved Terahertz Studies of Carrier Dynamics (b) T
(a) T << Tc
Tc
λ ξ
t2g
t2g
O 2p hole Tl 6s electron
Figure 4.23 Left: Photoexcited spin singlets for T << TC. The small circle is a domain with spin-down t2g states and embedded in the larger area which is a domain with spin-up t2g states. The e-h pairs recombine quickly in this temperature range. Right: Electron hole pairs after photoexcitation as T approaches TC from below. In this temperature range, holes within λ of a boundary migrate to domains of opposite t2g spin orientation (dotted arrows), effectively preventing electron-hole recombination.
To obtain a more quantitative understanding of the charge and spin dynamics in Tl2Mn2O7, the photo-induced change in carrier density (∆n) was extracted using the time-integrated optical conductivity and the reflectivity dynamics. The calculated photo-induced carrier density at 50 and 500 ps is plotted as a function of temperature in Figure 4.22(b). In region 1 (T < 90 K), the photo-induced carrier density at both time delays is nearly equal, increasing as T approaches TC. As T increases past TC, ∆n(t = 500 ps) remains nearly constant in region 2 (90 < T < 170 K) and then rapidly decreases in region 3 (T > 170 K), completely disappearing by 295 K. In the following paragraph, we focus on region 1. Further details regarding region 2 and 3 can be found in the original publication.154 Energy considerations and dipole selection rules dictate that the pump excitation creates e‑h spin singlets in the minority spin manifold. At the lowest temperatures the e-h singlets are created in a homogeneous background of t2g spins (Figure 4.23). Under these conditions, there is no energetic or dynamic constraint hindering recombination. That is, e-h wavefunction overlap in a spin singlet configuration occurs with a high probability, leading to recombination and a fast recovery of the carrier density (15 ps) as the data in Figure 4.22(a) shows. However, with increasing temperature a long-lived carrier density develops. This indicates that a competing pathway develops that stabilizes a fraction of the photoexcited carriers against recombination. A route for stabilizing a fraction of the initially photoexcited carriers is through the development of spatial fluctuations with a characteristic length scale given by the magnetic correlation length χ(T) of the Mn t2g spins responsible for ferromagnetic ordering. That is, small regions of opposite t2g spin develop in an otherwise homogeneous background. This is schematically depicted in Figure 4.23(a), in which, for T < TC the density of t2g (↓) domains is quite low, whereas it strongly increases upon approaching TC as shown in Figure 4.23(b). Of course, χ is also temperature- dependent, diverging at TC as for any ferromagnet, but χ ≈ 1 for T < 90 K in region 1,
7525_C004.indd 157
11/15/07 11:09:49 AM
158
Terahertz Spectroscopy: Principles and Applications
yielding a correlation length of order 0.1 nm.157 In this simple picture, we emphasize that the density of “defects” of opposite t2g orientation captures the essential physics of carrier stabilization. The spatial inhomogeneity that develops has important implications for photoexcited e-h pairs. From the bandstructure,154 it is energetically favorable for O 2p holes to cross a t2g (↑)–t2g(↓) boundary, whereas there is an energetic barrier for the Tl 6s electrons. Thus the spatial inhomogeneity in the t2g spin manifold leads to spatial segregation of the photoexcited Tl 6s electrons and O 2p holes, which in turn inhibits recombination. However, this process competes with recombination, and spatial segregation can only occur for holes that are initially created within a distance λ of a boundary as depicted in Figure 4.23. The net result is that with increasing temperature the number of “defects” increases, leading to an increase in the Tl 6s carrier density because more O 2p holes are trapped. Thus, in region 1, the amplitude of the fast relaxation component is due to recombination while that of the slow component is due to carrier stabilization. Therefore the photo-induced carrier density at t = 500 ps should be proportional to the ratio of slow to fast amplitudes in the ∆R/R traces. This in turn scales with the ratio of the volume occupied by t2g(↑) spins to that occupied by t2g(↓) spins, including a factor γ = (λ + χ)3. Here, γ is the effective volume where the probability of trapping an O 2p hole is greater than a recombination event. This results in an expression for the excess Tl 6s electron density ∆n given by Dn = C0
γ (1 - M ) 2 ξ 3 - γ (1 - M )
(4.12)
where the magnetization M is normalized to its saturation value and C0 is a proportionality constant. The solid line in Figure 4.22(b) shows ∆n plotted as a function of temperature for T < 90 K, revealing good agreement with the data. This analysis yields λ ~ 0.79 unit cells, indicating that the photoexcited holes can only travel a very short distance before recombining. In summary, spatial inhomogeneity that develops in the t2g spins (responsible for a decrease in M) stabilizes a fraction of the photoexcited carriers.154 These results are consistent with CMR in Tl2Mn2O7 arising from carrier localization from strong spin fluctuations without invoking phonons, which is in dramatic contrast to the results for the manganites where phonons (whether thermally disordered or of a polaronic nature) were crucial. These results also suggest that Tl2Mn2O7 may be a particularly simple example where the transport properties are determined by intrinsic nanoscale inhomogeneity occurring near a second-order phase transition.
4.5 Summary and Outlook We hope this chapter has revealed the potential of time-resolved THz techniques in the study of many-body correlations in bulk and nanostructured semiconductors, superconductors, and strongly correlated transition metal oxides. In semiconductors, we have reviewed experiments that study the free carrier response and buildup of
7525_C004.indd 158
11/15/07 11:09:51 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
159
Coulomb correlations, distinct signatures of intraexcitonic transitions that test the analogy between e-h gases and atomic systems, and the ultrafast polarization kinetics of intersubband transitions. Time domain THz spectroscopy provides for a direct determination of the real and imaginary parts of conductivity, which in superconductors directly reveals the quasiparticle and superfluid densities and the excitation gap 2∆ of the correlated charge pairs. Time resolving the conductivity dynamics, in turn, gives the most direct insight into the temporal breakup and recombination kinetics of quasiparticles in both conventional and high-TC superconductors. Time-resolved THz spectroscopy of manganites and pyrochlores gives important insight into dynamic spectral weight transfer, quasiparticle interactions with lattice and spin degrees of freedom, and stabilization processes of carriers through spatial inhomogeneities. Of course, these results barely scratch the surface of what is possible and within the context of dynamic studies on nanoscale and correlated materials there is still a great deal to be investigated. Intraexcitonic spectroscopy represents a rising field to investigate low-temperature carrier phases in semiconductors, where THz probes of optically dark states are of increasing interest in the search for excitonic BoseEinstein condensates.38,158 There are also a number of differences in the dynamics of YBCO and Bi-2212 presented in Section 4.3. It is not yet clear if these differences are intrinsic to the properties of these materials or are related to experimental parameters such as the incident fluence. It would be interesting to probe the dynamics for a larger range of materials and over a broader doping range. This holds for the manganites as well where, to date, dynamic optical pump THz probe experiments have only been performed on optimally doped samples (e.g., those that display halfmetallicity). However, as function of doping, the manganites display an enormous number of states including charge ordering, orbital ordering, and various magnetically ordered states. It will be important to understand the dynamics in each of these distinct phases especially as research on these materials focuses more and more on phenomena associated with phase coexistence.5,140 For example, recent mid-IR studies on Nd0.5Sr0.5MnO3, which transitions from paramagnetic semiconductor to ferromagnetic metal to charge-ordered insulator with decreasing temperature suggest that the dynamic polaron response provides a way to probe phase coexistence.159 There are also a host of other materials in which probing the mid- or far-IR dynamics can be expected to provide considerable insight. For example, several visible and x-ray experiments have studied the dynamics of VO2, giving insight into the insulator–metal transition and the cause–effect relationships between lattice and electronic degrees of freedom.160,161 Recent THz experiments complement these previous studies.162 This motivates, more generally, the study of photo-induced phase transitions both in materials where the phase transition is thermally accessible (as in VO2) and those where photoexcitation leads to a metastable state which is not thermodynamically accessible as observed previously.163 Other examples include f-electron intermetallics, in which hybridization between localized f moments and the conductions electrons results in a THz hybridization gap.164 All optical pump probe studies have been used to probe the quasiparticle dynamics as a function of temperature and show a strong dependence on the opening of a hybridization gap,165 but, to date, there have been no experiments which directly probe the dynamics at the gap edge as reported for superconductors.136 Finally, we mention the area of multiferroics,
7525_C004.indd 159
11/15/07 11:09:52 AM
160
Terahertz Spectroscopy: Principles and Applications
which is becoming an increasingly active research area. In multiferroics such as LuMnO3 or Ba0.5Sr1.5Zn2Fe12O22, there are two coexisting order parameters with the most common being ferroelectricity and antiferromagnetism. This leads to magnetoelectric coupling where the magnetic order can be modified with an electric field or vice versa.166–171 There is a great deal to be learned about these materials using both time-integrated and time-resolved optical spectroscopy. For example, using THz spectroscopy, electromagnons have recently been reported.172 This suggests that optical pump THz probe experiments may provide insight into the dynamics and microscopic origin of magnetoelectric coupling in these materials. In addition to probing the dynamics of other correlated-electron materials, experimental and theoretical advances are also expected to provide new opportunities. One area that seems to be very exciting is to use THz pulses with high peak electric fields as described in Section 4.2. Fields on the order of 1 MV/cm will enable coherent control of low-energy transitions in excitons and various nanoscale materials, and may lead to interesting nonlinear dynamics in correlated electron materials such as superconductors, manganites, and multiferroics. The majority of optical pump THz probe studies to date have used near-IR or visible pulses for photoexcitation. It would be of enormous value to have greater spectral agility for the photoexcitation. This is challenging in the case of optical pump THz probe spectroscopy because the pump spot size needs to be quite large (typically several millimeters) for uniform excitation of the THz probe beam, whereas the THz probe ideally must remain sensitive requiring fairly high repetition rates. Finally, we mention the need for a more concerted theoretical effort in this area. For semi-conductors, sophisticated models have been developed that provide insight into the fundamental quantum kinetics of carrier interactions.173 Likewise, it would be of considerable interest if such time domain theories were extended to encompass the physics of strongly correlated electron materials. While our contemporary understanding is naturally limited, we believe that the many facets of time-resolved THz techniques hold promise of unprecedented insight into the basic properties of complex materials.
Acknowledgments We thank our many collaborators on infrared and THz spectroscopy studies reviewed here, in particular D. S. Chemla, T. Elsaesser, M. Woerner, M. A. Carnahan, A. J. Taylor, S. A. Trugman, J. Demsar, R. P. Prasankumar, B. A. Schmid, R. Huber, J. F. Ryan, and many more. Preparation of this review was in part supported by the Office of Science of the U.S. Department of Energy under Contract DE-AC02-05CH11231 and by the Los Alamos National Laboratory LDRD program. We would also like to thank the authors of various articles for the permission to reproduce their figures in the preceding text.
References 1. Basov, D. N. and Timusk, T., Electrodynamics of high-TC superconductors, Rev. Mod. Phys. 77, 721–779, 2005. 2. Bednorz, J. G. and Müller, K. A., Possible high TC superconductivity in the Ba- La-Cu-O system, Z. Phys. B 64, 189–93, 1986.
7525_C004.indd 160
11/15/07 11:09:54 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
161
3. Bonn, D. A., Are high-temperature superconductors exotic? Nat. Phys. 2, 159–168, 2006. 4. Coey, J. M. D., Viret, M., and von Molnar, S., Mixed-valence manganites, Adv. Phys. 48, 167–293, 1999. 5. Dagotto, E., Hotta, T., and Moreo, A., Colossal magnetoresistant materials: the key role of phase separation, Phys. Rep. 344, 1–153, 2001. 6. Fazekas, P., Lecture notes on electron correlation and magnetism. Singapore: World Scientific, 1999. 7. Imada, M., Fujimori, A., and Tokura, Y., Metal-insulator transitions, Rev. Mod. Phys. 70, 1039–1263, 1998. 8. Orenstein, J. and Millis, A. J., Advances in the physics of high-temperature superconductivity, Science 288, 468–474, 2000. 9. Salamon, M. B. and Jaime, M., The physics of manganites: structure and transport, Rev. Mod. Phys. 73, 583–628, 2001. 10. Tinkham, M., Introduction to superconductivity, 2nd ed., New York: McGraw-Hill, 1996. 11. Chemla, D. S., Correlation and coherence in semiconductors, Comptes Rendus De L’ Academie Des Sciences Serie IV Physique Astrophysique 2 (10), 1427–1438, 2001. 12. Shah, J., Ultrafast spectroscopy of semiconductors and semiconductor nanostructures, Berlin: Springer Verlag, 1999. 13. Nuss, M. C. and Orenstein, J., in Millimeter and submillimeter wave spectroscopy of solids, Grüner, G. Berlin: Springer Verlag, 1998. 14. Cooper, S. L., Optical spectroscopic studies of metal insulator transitions, perovskiterelated oxides, Structure and Bonding 98, 161–218, 2001. 15. Li, X. Q., Zhang, T. H., Borca, C. N., and Cundiff, S. T., Many-body interactions in semiconductors probed by optical two-dimensional Fourier transform spectroscopy, Phys. Rev. Lett. 96, 057406, 2006. 16. Hickey, B. J., Morgan, G. J., and Howson, M. A., Basic electron transport, in Spin electronics, Thornton, M. J. and Ziese, M., ed. Berlin, Heidelburg, Springer-Verlag, 2001. 17. Puchkov, A. V., Basov, D. N., and Timusk, T., The pseudogap state in high-Tc superconductors: an infrared study, J. Phys. Cond. Mat. 8, 1996. 18. Tsai, T.-R., Chen, S.-J., Chang, C.-F., Hsu, S.-H., and Lin, T.-Y., Terahertz response of GaN thin films, Optics Express 14 (11), 4898–4907, 2005. 19. Jeon, T.-I. and Grischkowsky, D., Nature of conduction in doped silicon, Phys. Rev. Lett. 78, 1106–1109, 1997. 20. Lui, K. P. H. and Hegmann, F. A., Ultrafast carrier relaxation in radiation-damaged silicon on sapphire studied by optical pump terahertz probe experiments, Appl. Phys. Lett. 78, 3478–3480, 2001. 21. Prasankumar, R. P., Scopatz, A., Hilton, D. J., Taylor, A. J., Averitt, R. D., Zide, J. M., and Gossard, A. C., Carrier dynamics in self-assembled ErAs nanoislands embedded in GaAs measured by optical pump terahertz-probe spectroscopy, Appl. Phys. Lett. 86, 201107, 2005. 22. Schmuttenmaer, C. A., Exploring dynamics in the far-infrared with terahertz spectroscopy, Chem. Revi. 104, 1759–1779, 2004. 23. Huber, R., Tauser, F., Brodschlem, A., Bichler, M., Abstreiter, G., and Leitenstorfer, A., How many-particle interactions develop after ultrafast excitation of an electronhole plasma, Nature 414, 286–289, 2001. 24. Wu, Q. and Zhang, X.-C., Free-space electro-optics sampling of mid-infrared pulses, Appl. Phys. Lett. 71, 1285–1286, 1997.
7525_C004.indd 161
11/15/07 11:09:55 AM
162
Terahertz Spectroscopy: Principles and Applications
25. Kaindl, R. A., Smith, D. C., Joschko, M., Hasselbeck, M. P., Woerner, M., and Elsaesser, T., Femtosecond infrared pulses tunable from 9 to 18 mm at an 88-MHz repetition rate, Opt. Lett. 23, 861–863, 1998. 26. Bartel, T., Gaal, P., Reimann, K., Woerner, M., and Elsaesser, T., Generation of singlecycle THz transients with high electric-field amplitudes, Opt. Lett. 30, 2805–2807, 2005. 27. You, D., Jones, R. R., Bucksbaum, P. H., and Dykaar, D. R., Generation of high-power sub-single-cycle 500-fs electromagnetic pulses, Opt. Lett. 18, 290–292, 1993. 28. Feurer, T., Vaughan, J. C., and Nelson, K. A., Spatiotemporal coherent control of lattice vibrational waves, Science 299, 374–377, 2003. 29. van Tilborg, J., Schroeder, C. B., Filip, C. V., et al., Temporal characterization of femtosecond laser-plasma-accelerated electron bunches using terahertz radiation, Phys. Rev. Lett. 96, 014801, 2006. 30. Gaal, P., Reimann, K., Woerner, M., Elsaesser, T., Hey, R., and Ploog, K. H., Nonlinear terahertz response of n-type GaAs, Phys. Rev. Lett. 96, 187402, 2006. 31. Chemla, D. S. and Shah, J., Many-body and correlation effects in semiconductors, Nature 411, 549–557, 2001. 32. Haken, H., Die Theorie des Exzitons in festen Körper, Fortschr. Phys. vol. 6, 38 (271-234), 1958. 33. Nikitine, S., On the possibility of observation and the intensity of (nn’) and (nn) transitions between exciton-states in Cu2O, J. Phys. Chem. Solids 45, 949, 1984. 34. Timusk, T., Far-infrared absorption study of exciton ionization in germanium, Phys. Rev. B 13, 3511–3514, 1976. 35. Cerne, J., Kono, J., Sherwin, M. S., Sundaram, M., Gossard, A. C., and Bauer, G. E. W., Terahertz dynamics of excitons in GaAs/AlGaAs quantum wells, Phys. Rev. Lett. 77, 1131–1134, 1996. 36. Groeneveld, R. H. M. and Grischkowsky, D., Picosecond time-resolved far-infrared experiments on carriers and excitons in GaAs-AlGaAs multiple quantum wells, J. Opt. Soc. Am. B 11, 2502, 1994. 37. Kaindl, R. A., Carnahan, M. A., Hägele, D., Lövenich, R., and Chemla, D. S., Ultrafast terahertz probes of transient conducting and insulating phases in an electronhole gas, Nature 423, 734–738, 2003. 38. Kubouchi, M., Yoshioka, K., Shimano, R., Mysyrowicz, A., and Kuwata-Gonokami, M., Study of orthoexciton-to-paraexciton conversion in Cu2O by excitonic Lyman spectroscopy, Phys. Rev. Lett. 94, 016403, 2005. 39. Johnsen, K. and Kavoulakis, G. M., Probing Bose-Einstein condensation of excitons with electromagnetic radiation, Phys. Rev. Lett. 86, 858–861, 2001. 40. Kira, M., Hoyer, W., Stroucken, T., and Koch, S. W., Exciton formation in semiconductors and the influence of a photonic environment, Phys. Rev. Lett. 87, 176401, 2001. 41. Koch, S. W., Kira, M., Khitrova, G., and Gibbs, H. M., Semiconductor excitons in new light, Nat. Materials 5, 523–531, 2006. 42. Ekenberg, U. and Altarelli, M., Exciton binding energy in a quantum well with inclusion of valence-band coupling and nonparabolicity, Phys. Rev. B 35, 7585, 1987. 43. Haug, H. and Koch, S. W., Quantum theory of the optical and electronic properties of semiconductors, Signapore: World Scientific, 2004. 44. Kaindl, R. A., Hägele, D., Carnahan, M. A., and Chemla, D. S., Transient terahertz spectroscopy of excitons and unbound carriers in quasi two-dimensional electronhole gases. Unpublished. 45. Oh, I. K., Singh, J., Thilagam, A., and Vengurlekar, A. S., Exciton formation assisted by LO phonons in quantum wells, Phys. Rev. B 62, 2045–2050, 2000.
7525_C004.indd 162
11/15/07 11:09:56 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
163
46. Selbmann, P. E., Gulia, M., Rossi, F., Molinari, E., and Lugli, P., Coupled free-carrier and exciton relaxation in optically excited semiconductors, Phys. Rev. B 54, 4660, 1996. 47. Siantidis, K., Axt, V. M., and Kuhn, T., Dynamics of exciton formation for near band gap excitations, Phys. Rev. B 65, 035303, 2002. 48. Huber, R., Kaindl, R. A., Schmid, B. A., and Chemla, D. S., Broadband terahertz study of excitonic resonances in the high-density regime in GaAs/AlxGa1-xAs quantum wells, Phys. Rev. B 72, 161314, 2005. 49. Huber, R., Schmid, B. A., Shen, Y. R., Chemla, D. S., and Kaindl, R. A., Stimulated terahertz emission from intra-excitonic transitions in Cu2O, Phys. Rev. Lett. 96, 017402, 2006. 50. Kira, M. and Koch, S. W., Exciton-population inversion and terahertz gain in semiconductors excited to resonance, Phys. Rev. Lett. 93, 076402, 2004. 51. Uihlein, C., Fröhlich, D., and Kenklies, R., Investigation of exciton fine structure in Cu2O, Phys. Rev. B 23, 2731, 1981. 52. Keldysh, L. V. and Kozlov, A. N., Collective properties of excitons in semiconductors, Sov. Phys. JETP 27, 521, 1968. 53. Butov, L. V., Gossard, A. C., and Chemla, D. S., Macroscopically ordered state in an exciton system, Nature 418, 751–754, 2002. 54. Lai, C. W., Zoch, J., Gossard, A. C., and Chemla, D. S., Phase diagram of degenerate exciton systems, Science 303, 503–506, 2004. 55. Snoke, D., Spontaneous Bose coherence of excitons and polaritons, Science 298, 1368, 2002. 56. O’Hara, K. E. and Wolfe, J. P., Relaxation kinetics of excitons in cuprous oxide, Phys. Rev. B 62, 12909–12922, 2000. 57. Jang, J. I. and Wolfe, J. P., Biexcitons in the semiconductor Cu2O: an explanation of the rapid decay of excitons, Phys. Rev. B 72, 241201, 2005. 58. Jang, J. I. and Wolfe, J. P., Relaxation of stress-split orthoexcitons in Cu2O, Phys. Rev. B 73, 075207, 2006. 59. Jolk, A., Jörger, M., and Klingshirn, C., Exciton lifetime, Auger recombination, and exciton transport by calibrated difference absorption spectroscopy in Cu2O, Phys. Rev. B 65, 245209, 2002. 60. Göppert, M., Becker, R., Maier, C., Jörger, M., Jolk, A., and Klingshirn, C., Infrared absorption by excitons in cuprous oxide, Int. J. Mod. Phys. B 15, 3615–3618, 2001. 61. Jörger, M., Tsitsishvili, E., Fleck, T., and Klingshirn, C., Infrared absorption by excitons in Cu2O, phys. Stat. Sol. (B) 238, 470–473, 2003. 62. Karpinska, K., Mostovoy, M., van der Vegte, M. A., Revcolevschi, A., and van Loosdrecht, P. H. M., Decay and coherence of two-photon excited yellow orthoexcitons in Cu2O, Phys. Rev. B 72, 155201, 2005. 63. Kuwata-Gonokami, M., Observation of ortho and para-excitons by time-resolved excitonic Lyman spectroscopy, Solid State Comm. 134, 127–133, 2005. 64. Kuwata-Gonokami, M., Kubouchi, M., Shimano, R., and Mysyrowicz, A., Timeresolved excitonic Lyman spectroscopy of Cu2O, J. Phys. Soc. Jpn. 73, 1065–1069, 2004. 65. Kamgar, A., Kneschaurek, P., Dorda, G., and Koch, J. F., Resonance spectroscopy of electronic levels in a surface accumulation layer, Phys. Rev. Lett. 32, 1251–1254, 1974. 66. West, L. C. and Eglash, S. J., First observation of an extremely large-dipole infrared transition within the conduction band of a GaAs quantum well, Appl. Phys. Lett. 46, 1156–1158, 1985. 67. Faist, J., Capasso, F., Sivco, D. L., Sirtori, C., Hutchinson, A. L., and Cho, A. Y., Quantum cascade laser, Science 264, 553–556, 1994.
7525_C004.indd 163
11/15/07 11:09:58 AM
164
Terahertz Spectroscopy: Principles and Applications
68. Kohler, R., Tredicucci, A., Beltram, F., et al., Terahertz semiconductor-heterostructure laser, Nature 417, 156–159, 2002. 69. Seilmeier, A., Hübner, H.-J., Abstreiter, G., Weimann, G., and Schlapp, W., Intersubband relaxation in GaAs-AlxGa1-xAs quantum well structures observed directly by an infrared bleaching technique, Phys. Rev. Lett. 59, 1345–1348, 1987. 70. Bäuerle, R. J., Elsaesser, T., Lobentanzer, H., Stolz, W., and Ploog, K., Transient reshaping of intersubband absorption spectra due to hot-electrons in a modulationdoped multiple-quantum-well structure, Phys. Rev. B 40, 10002–10005, 1989. 71. Lutgen, S., Kaindl, R. A., Woerner, M., Elsaesser, T., Hase, A., and Kunzel, H., Nonlinear intersubband absorption of a hot quasi-two-dimensional electron plasma studied by femtosecond infrared spectroscopy, Phys. Rev. B 54, 17343–17346, 1996. 72. Lutgen, S., Kaindl, R. A., Woerner, M., Elsaesser, T., Hase, A., Kunzel, H., Gulia, M., Meglio, D., and Lugli, P., Nonequilibrium dynamics in a quasi-two-dimensional electron plasma after ultrafast intersubband excitation, Phys. Rev. Lett. 77, 3657–3660, 1996. 73. Kaindl, R. A., Wurm, M., Reimann, K., Woerner, M., Elsaesser, T., Miesner, C., Brunner, K., and Abstreiter, G., Ultrafast dynamics of intersubband excitations in a quasi-two-dimensional hole gas, Phys. Rev. Lett. 86, 1122–1125, 2001. 74. Heyman, J. N., Unterrainer, K., Craig, K., et al., Far-infrared pump–probe measurements of the intersubband lifetime in an AlGaAs/GaAs coupled-quantum well, Appl. Phys. Lett. 68, 3019–3021, 1996. 75. Müller, T., Parz, W., Strasser, G., and Unterrainer, K., Influence of carrier–carrier interaction on time-dependent intersubband absorption in a semiconductor quantum well, Phys. Rev. B 70, 155324, 2004. 76. Bonvalet, A., Nagle, J., Berger, V., Migus, A., Martin, J.-L., and Joffre, M., Femtosecond infrared emission resulting from coherent charge oscillations in quantum wells, Phys. Rev. Lett. 76, 4392–4395, 1996. 77. Planken, P. C. M., Nuss, M. C., Brener, I., Goossen, K. W., Luo, M. S. C., Chuang, S.-L., and Pfeiffer, L., Terahertz emission in single quantum wells after coherent optical excitation of light hole and heavy hole excitons, Phys. Rev. Lett. 69, 3800–3803, 1992. 78. Roskos, H. G., Nuss, M. C., Shah, J., Leo, K., Miller, D. A. B., Fox, A. M., Schmitt-Rink, S., and Köhler, K., Coherent submillimeter wave emission from charge oscillations in a double-well potential, Phys. Rev. Lett. 68, 2216–2219, 1992. 79. Bratschitsch, R., Muller, T., Kersting, R., Strasser, G., and Unterrainer, K., Coherent terahertz emission from optically pumped intersubband plasmons in parabolic quantum wells, Appl. Phys. Lett. 76, 3501–3503, 2000. 80. Waschke, C., Roskos, H. G., Schwedler, R., Leo, K., Kurz, H., and Köhler, K., Coherent submillimeter-wave emission from Bloch oscillations in a semiconductor superlattice, Phys. Rev. Lett. 70, 3319–3322, 1993. 81. Kaindl, R. A., Lutgen, S., Woerner, M., et al., Ultrafast dephasing of coherent intersubband polarizations in a quasi-two-dimensional electron plasma, Phys. Rev. Lett. 80, 3575–3578, 1998. 82. Kaindl, R. A., Reimann, K., Woerner, M., Elsaesser, T., Hey, R., and Ploog, K. H., Homogeneous broadening and excitation-induced dephasing of intersubband transitions in a quasi-two-dimensional electron gas, Phys. Rev. B 63, 161308, 2001. 83. Eickemeyer, F., Reimann, K., Woerner, M., et al., Ultrafast coherent electron transport in semiconductor quantum cascade structures, Phys. Rev. Lett. 89, 047402, 2002.
7525_C004.indd 164
11/15/07 11:09:59 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
165
84. Carter, S. G., Ciulin, V., Hanson, M., Huntington, A. S., Wang, S., Gossard, A. C., Coldren, L. A., and Sherwin, M. S., Terahertz-optical mixing in undoped and doped GaAs quantum wells from excitonic to electronic intersubband transitions, Phys. Rev. B 72, 155309, 2005. 85. Craig, K., Galdrikian, B., Heyman, J. N., Markelz, A. G., Williams, J. B., Sherwin, M. S., Campman, K., Hopkins, P. F., and Gossard, A. C., Undressing a collective intersubband excitation in a quantum well, Phys. Rev. Lett. 76, 2382–2385, 1996. 86. Luo, C. W., Reimann, K., Woerner, M., Elsaesser, T., Hey, R., and Ploog, K. H., Phase- resolved nonlinear response of a two-dimensional electron gas under femtosecond intersubband excitation, Phys. Rev. Lett. 92, 047402, 2004. 87. Shih, T., Reimann, K., Woerner, M., Elsaesser, T., Waldmuller, I., Knorr, A., Hey, R., and Ploog, K., Nonlinear response of radiatively coupled intersubband transitions of quasi-two-dimensional electrons, Phys. Rev. B 72, 195338, 2005. 88. Waldmueller, I., Chow, W. W., and Knorr, A., Influence of radiative coupling on coherent Rabi intersubband oscillations in multiple quantum wells, Phys. Rev. B 73, 035433, 2006. 89. Cole, B. E., Williams, J. B., King, B. T., Sherwin, M. S., and Stanley, C. R., Coherent manipulation of semiconductor quantum bits with terahertz radiation, Nature 410, 60–63, 2001. 90. Frogley, M. D., Dynes, J. F., Beck, M., Faist, J., and Phillips, C. C., Gain without inversion in semiconductor nanostructures, Nat. Materials 5, 175–178, 2006. 91. Sherwin, M. S., Imamoglu, A., and Montroy, T., Quantum computation with quantum dots and terahertz cavity quantum electrodynamics, Phys. Rev. A 60, 3508–3514, 1999. 92. Batista, A. A., Pulse-driven interwell carrier transfer in n-type doped asymmetric double quantum wells, Phys. Rev. B 73, 075305, 2006. 93. Paspalakis, E., Tsaousidou, M., and Terzis, A. F., Coherent manipulation of a strongly driven semiconductor quantum well, Phys. Rev. B 73, 125344, 2006. 94. Bardeen, J., Cooper, L. N., and Schrieffer, J. R., Theory of superconductivity, Phys. Rev. 108, 1175–1204, 1957. 95. Mattis, D. C. and Bardeen, J., Theory of the anomalous skin effect in normal and superconducting metals, Phys. Rev. 111, 412–417, 1958. 96. Glover, R. E. and Tinkham, M., Conductivity of superconducting films for photon energies between 0.3 and 40kTc, Phys. Rev. 108, 243–256, 1957. 97. Miller, B. I. and Dayem, A. H., Relaxation and recombination times of quasiparticles in superconducting Al thin films, Phys. Rev. Lett. 18 (23), 1000–1004, 1967. 98. Rothwarf, A. and Taylor, B. N., Measurement of recombination lifetimes in superconductors, Phys. Rev. Lett. 3, 27–30, 1967. 99. Gray, K. E., Nonequilibrium superconductivity, phonons, and kaptiza boundaries. New York: Plenum, 1981. 100. Kaplan, S. B., Chi, C. C., Langenberg, D. N., Chang, J. J., Jafarey, S., and Scalapino, D. J., Quasiparticle and phonon lifetimes in superconductors, Phys. Rev. B 14, 4854– 4873, 1976. 101. Schuller, I. and Gray, K. E., Experimental observation of the relaxation time of the order parameter in superconductors, Phys. Rev. Lett. 36, 429–432, 1976. 102. Testardi, L. R., Destruction of superconductivity by laser light, Phys. Rev. B 4, 2189– 2196, 1971. 103. Allen, J. W., Aronson, M., Boebinger, G. S., Broholm, C. L., Cooper, S. L., Crow, J. E., Hammel, P. C., and Lander, G., Future probes in materials science, Physica B 318, 12–23, 2002. 104. Eesley, G. L., Observation of non-equilibrium heating in copper, Phys. Rev. Lett. 51, 2140–2143, 1983.
7525_C004.indd 165
11/15/07 11:10:01 AM
166
Terahertz Spectroscopy: Principles and Applications
105. Schoenlein, R. W., Lin, W. Z., Fujimoto, J. G., and Eesley, G. L., Femtosecond studies of nonequilibrium electronic processes in metals, Phys. Rev. Lett. 58, 1680–1683, 1987. 106. Brorson, S. D., Buhleier, R., Trofimov, I. E., White, J. O., Ludwig, C., Balakirev, F. F., Habermeier, H.-U., and Kuhl, J., Electrodynamics of high-temperature superconductors investigated with coherent terahertz pulse spectroscopy, J. Opt. Soc. Am. B 13, 1979–1993, 1996. 107. Demsar, J., Podobnik, B., Kabanov, V. V., Wolf, T., and Mihailovic, D., Superconducting gap Dc, the pseudogap DP, and pair fluctuations above TC in overdoped Y1-xCaxBa2Cu3O7-delta from femtosecond time domain spectroscopy, Phys. Rev. Lett. 82, 4918–4921, 1999. 108. Han, S. G., Vardeny, Z. V., Wong, K. S., Symko, O. G., and Koren, G., Femtosecond optical detection of quasiparticle dynamics in high-TC YBa2Cu3O7-δ superconducting thin films, Phys. Rev. Lett. 65, 2708, 1990. 109. Nuss, M. C., Goossen, K. W., Mankiewich, P. M., and O’Malley, M. L., Terahertz surface impedance of thin YBa2Cu3O7 superconducting films, Appl. Phys. Lett. 58, 2561–2563, 1991. 110. Palmer, L. H. and Tinkham, M., Far-infrared absorption in thin superconducting lead films, Phys. Rev. 165, 588–595, 1968. 111. Jaekel, C., Waschke, C., Roskos, H. G., Kurz, H., Prusseit, W., and Kinder, W., Surface resistance and penetration depth of YBa2Cu3O7–δ thin films on silicon at ultrahigh frequencies, Appl. Phys. Lett. 64, 3326–3328, 1994. 112. Nuss, M. C., Mankiewich, P. M., O’Malley, M. L., Westerwick, E. H., and Littlewood, P. B., Dynamic conductivity and coherence peak in YBa2Cu3O7 superconductors, Phys. Rev. Lett. 66, 3305–3308, 1991. 113. Wilke, I., Khazan, M., Rieck, C. T., Kuzel, P., Kaiser, T., Jaekel, C., and Kurz, H., Terahertz surface resistance of high temperature superconducting thin films, J. Appl. Phys. 87, 2984–2988, 2000. 114. Kaindl, R. A., Carnahan, M. A., Orenstein, J., Chemla, D. S., Christen, H. M., Zhai, H. Y., Paranthaman, M., and Lowndes, D. H., Far-infrared optical conductivity gap in superconducting MgB2 films, Phys. Rev. Lett. 88, 027003, 2002. 115. Nagamatsu, J., Nakagawa, N., Muranaka, T., Zenitani, Y., and Akimitsu, J., Superconductivity at 39 K in magnesium diboride, Nature 410, 63–64, 2001. 116. Born, M. and Wolf, E., Principles of optics. Cambridge: University Press, 1999. 117. Choi, H. J., Roundy, D., Sun, H., Cohen, M. L., and Louie, S. G., The origin of the anomalous superconducting properties of MgB2, Nature 418, 758–760, 2002. 118. Kortus, J., Mazin, I. I., Belashchenko, K. D., Antropov, V. P., and Boyer, L. L., Superconductivity of metallic boron in MgB2, Phys. Rev. Lett. 86, 4656–4659, 2001. 119. Liu, A. Y., Mazin, I. I., and Kortus, J., Beyond Eliashberg superconductivity in MgB2: anharmonicity, two-phonon scattering, and multiple gaps, Phys. Rev. Lett. 87, 087005, 2001. 120. Hosseini, A., Harris, R., Kamal, S., Dosanjh, P., Preston, J., Liang, R. X., Hardy, W. N., and Bonn, D. A., Microwave spectroscopy of thermally excited quasiparticles in YBa2Cu3O6.99, Phys. Rev. B 60, 1349–1359, 1999. 121. Corson, J., Orenstein, J., Oh, S., O'Donnell, J., and Eckstein, J. N., Nodal quasiparticle lifetime in the superconducting state of Bi2Sr2CaCu2O8+δ, Phys. Rev. Lett. 85, 2569, 2000. 122. Corson, J., Mallozi, R., Orenstein, J., Eckstein, J. N., and Bozovic, I., Vanishing of phase coherence in underdoped Bi2Sr2CaCu2O8+δ, Nature 398, 221–223, 1999.
7525_C004.indd 166
11/15/07 11:10:03 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
167
123. Demsar, J., Averitt, R. D., Taylor, A. J., et al., Pair-breaking and superconducting state recovery dynamics in MgB2, Phys. Rev. Lett. 91, 267002-4, 2003. 124. Kang, W. N., Kim, H. J., Choi, E. M., Jung, C. U., and Lee, S. I., MgB2 superconducting thin films with a transition temperature of 39 Kelvin, Science 292, 1521–1523, 2001. 125. Carr, G. L., Lobo, R., LaVeigne, J., Reitze, D. H., and Tanner, D. B., Exploring the dynamics of superconductors by time-resolved far-infrared spectroscopy, Phys. Rev. Lett. 85, 3001-4, 2000. 126. Federici, J. F., Greene, B. I., Saeta, P. N., Dykaar, D. R., Sharifi, F., and Dynes, R. C., Direct picosecond measurement of photo-induced Cooper-pair breaking in lead, Phys. Rev. B 46, 11153–11156, 1992. 127. Norman, M. R. and Pepin, C., The electronic nature of high temperature cuprate superconductors, Rep. Prog. Phys. 66, 1547, 2003. 128. Gay, P., Smith, D. C., Stevens, C. J., Chen, C., Yang, G., Abell, S. J., Wang, D. Z., Wang, J. H., Ren, Z. F., and Ryan, J. F., Femtosecond dynamics of BSCCO-2212, J. Low Temp. Phys. 117, 1025, 1999. 129. Gedik, N., Blake, P., Spitzer, R. C., Orenstein, J., Liang, R., Bonn, D. A., and Hardy, W. N., Single-quasiparticle stability and quasiparticle-pair decay in YBa2Cu3O6.5, Phys. Rev. B 70, 014504, 2004. 130. Segre, G. P., Gedik, N., Orenstein, J., Bonn, D. A., Liang, R., and Hardy, W. N., photo-induced changes of reflectivity in single crystals of YBa2Cu3O6.5 (Ortho II), Phys. Rev. Lett. 88, 137001, 2002. 131. Averitt, R. D., Rodriguez, G., Lobad, A. I., Siders, J. L. W., Trugman, S. A., and Taylor, A. J., Nonequilibrium superconductivity and quasiparticle dynamics in YBa2Cu3O7-δ, Phys. Rev. B 63, 140502, 2001. 132. Averitt, R. D., Thorsmolle, V. K., Jia, Q. X., Trugman, S. A., and Taylor, A. J., Nonequilibrium superconductivity in Y(1-x)PrxBa(2)Cu(3)O(7) thin films, Physica B 312, 86–87, 2002. 133. Kaindl, R. A., Carnahan, M. A., Chemla, D. S., Oh, S., and Eckstein, J. N., Dynamics of Cooper pair formation in Bi2Sr2CaCu2O8+δ, Phys. Rev. B 72, 060510(R), 2005. 134. McElroy, K., Simmonds, R. W., Hoffman, J. E., Lee, D. H., Orenstein, J., Eisaki, H., Uchida, S., and Davis, J. C., Relating atomic-scale electronic phenomena to wavelike quasiparticle states in superconducting Bi2Sr2CaCu2O8+δ, Nature 422, 592–596, 2003. 135. Timusk, T. and Statt, B., The pseudogap in high-temperature superconductors: an experimental survey, Rep. Prog. Phys. 62, 61–122, 1999. 136. Kaindl, R., Woerner, M., Elsaesser, T., Smith, D. C., Ryan, J. F., Farnan, G. A., McCurry, M. P., and Walmsley, D. G., Ultrafast mid-infrared response of YBa2Cu3O7, Science 287, 470–473, 2000. 137. Kaindl, R. A., Woerner, M., Elsaesser, T., Smith, D. C., Ryan, J. F., Farnan, G. A., McCurry, M. P., and Walmsley, D. G., Ultrafast mid-infrared response of YBa2Cu3O7-δ, Science 287, 470–473, 2000. 138. Kaindl, R. A., Woerner, M., Elsaesser, T., Smith, D. C., Ryan, J. F., Farnan, G. A., McCurry, M. P., and Walmsley, D. G., Femtosecond mid-infrared study of YBa2Cu3O7-δ, Physica C 341, 2213–2216, 2000. 139. Brorson, S. D., Kazeroonian, A., Moodera, J. S., Face, D. W., Cheng, T. K., Ippen, E. P., Dresselhaus, M. S., and Dresselhaus, G., Femtosecond room-temperature measurement of the electron-phonon coupling constant γ in metallic superconductors, Phys. Rev. Lett. 64, 2172–2175, 1990. 140. Dagotto, E., Complexity in strongly correlated electronic systems, Science 309, 257– 262, 2005.
7525_C004.indd 167
11/15/07 11:10:04 AM
168
Terahertz Spectroscopy: Principles and Applications
141. Jin, S., Tiefel, T. H., McCormack, M., Fastnacht, R. A., Ramesh, R., and Chen, L. H., Thousandfold change in resistivity in magnetoresistive La-Ca-Mn-O films, Science 264, 413–415, 1994. 142. Anderson, P. W., and Hasegawa, H., Considerations on double exchange, Phys. Rev. 100, 675–681, 1955. 143. Jonker, G. H. and van Santen, J. H., Ferromagnetic compounds of manganese with perovskite structure, Physica 16, 337–349, 1950. 144. van Santen, J. H., and Jonker, G. H., Electrical conductivity of ferromagnetic compounds of manganese with perovskite structure, Physica 16, 599–600, 1950. 145. Wollan, E. O., and Koehler, W. C., Neutron diffraction study of the magnetic properties of the series of perovskite-type compounds [(1-x)La,xCa]MnO3, Phys. Rev. 100, 545–563, 1955. 146. Zener, C., Interaction between the d-shells in the transition metals. II. Ferromagnetic compounds of manganese with perovskite structure, Phys. Rev. 82, 403–405, 1951. 147. Millis, A. J., Shraiman, B. I., and Mueller, R., Dynamic Jahn-Teller effect and colossal magnetoresistance in La1-xSrxMnO3, Phys. Rev. Lett. 77, 175–178, 1996. 148. Roder, H., Zang, J., and Bishop, A. R., Lattice effects in the colossal-magnetoresistance manganites, Phys. Rev. Lett. 76, 1356–1359, 1996. 149. Ramirez, A. P., Colossal magnetoresistance, J. Phys. Cond. Mat. 9, 8171–8199, 1997. 150. Shimakawa, Y., Kubo, Y., and Manako, T., Giant magnetoresistance in Tl2Mn2O7 with the pyrochlore structure, Nature 379, 53–55, 1996. 151. Subramanian, M. A., Toby, B. H., Ramirez, A. P., Marshall, W. J., Sleight, A. W., and Kwei, G. H., Colossal magnetoresistance without Mn3+/Mn4+ double exchange in the stoichiometric pyrochlore Tl2Mn2O7, Science 273, 81–84, 1996. 152. Averitt, R. D., Lobad, A. I., Kwon, C., Trugman, S. A., Thorsmolle, V. K., and Taylor, A. J., Ultrafast conductivity dynamics in colossal magnetoresistance manganites, Phys. Rev. Lett. 87, 017401, 2001. 153. Okamura, H., Koretsune, T., Matsunami, M., Kimura, S., Nanba, T., Imai, H., Shimakawa, Y., and Kubo, Y., Charge dynamics in the colossal magnetoresistance pyrochlore Tl2Mn2O7, Phys. Rev. B 64, 180409, 2001. 154. Prasankumar, R. P., Okamura, H., Imai, H., Shimakawa, Y., Kubo, Y., Trugman, S. A., Taylor, A. J., and Averitt, R. D., Coupled charge-spin dynamics of the magnetoresistive pyrochlore Tl2Mn2O7 probed using ultrafast midinfrared spectroscopy, Phys. Rev. Lett. 95, 267404, 2005. 155. Quijada, M., Cerne, J., Simpson, J. R., Drew, H. D., Ahn, K. H., Millis, A. J., Shreekala, R., Ramesh, R., Rajeswari, M., and Venkatesan, T., Optical conductivity of manganites: crossover from Jahn-Teller small polaron to coherent transport in the ferromagnetic state, Phys. Rev. B 58, 16093–16102, 1998. 156. Averitt, R. D. and Taylor, A. J., Ultrafast optical and far-infrared quasiparticle dynamics in correlated electron materials, J. Phys. Cond. Mat. 14, R1357–1390, 2002. 157. Lynn, J. W., Vasiliu-Doloc, L., and Subramanian, M. A., Spin dynamics of the magnetoresistive pyrochlore Tl2Mn2O7, Phys. Rev. Lett. 80, 4582–4585, 1998. 158. Butov, L. V., Levitov, L. S., Mintsev, A. V., Simons, B. D., Gossard, A. C., and Chemla, D. S., Formation mechanism and low-temperature instability of exciton rings, Phys. Rev. Lett. 92, 117404, 2004. 159. Prasankumar, R. P., Lee, H. J., Zvyagin, S., Kamenev, K. V., Balakrishnan, G., Mck. Paul, D., Taylor, A. J., and Averitt, R. D., Probing nanoscale inhomogeneities through the polaronic response. In preparation. 160. Cavalleri, A., Rini, M., Chong, H. H. W., Fourmaux, S., Glover, T. E., Heimann, P. A., Keiffer, J. C., and Schoenlein, R. W., Band-selective measurements of electron dynamics in VO2 using femtosecond near-edge x-ray absorption, Phys. Rev. Lett. 95, 067405, 2005.
7525_C004.indd 168
11/15/07 11:10:06 AM
Time-Resolved Terahertz Studies of Carrier Dynamics
169
161. Cavalleri, A., Toth, C., Siders, C. W., Squier, J. A., Raksi, F., Forget, P., and Keiffer, J. C., Femtosecond structural dynamics in VO2 during an ultrafast solid-solid phase transition, Phys. Rev. Lett. 87, 237401, 2001. 162. Hilton, D. J., Prasankumar, R. P., Trugman, S. A., Taylor, A. J., Averitt, R. D., On photo-induced phenomena in complex materials: probing quasiparticle dynamics using infrared and far-infrared pulses, J. Phys. Soc. Jpn. 75, 011006, 2006. 163. Suzuki, T., Sakamaki, T., Tanimura, K., Koshihara, S., and Tokura, Y., Ionic-to- neutral phase transformation induced by photoexcitation of the charge-transfer band in tetrathiafulvalene-p-chloranil crystals, Phys. Rev. B 60, 6191–6193, 1999. 164. Hancock, J. N., McKnew, T., Schlesinger, Z., Sarrao, J. L., and Fisk, Z., Kondo scaling in the optical response of YbIn1-xAgxCu4, Phys. Rev. Lett. 92, 186405, 2004. 165. Demsar, J., Averitt, R. D., Ahn, K. H., Graf, M. J., Trugman, S. A., Kabanov, V. V., Sarrao, J. L., and Taylor, A. J., Quasiparticle relaxation dynamics in heavy fermion compounds, Phys. Rev. Lett. 91, 027401–4, 2003. 166. Feibig, M., Revival of the magnetoelectric effect, J. Phy. D: Appl.Phys. 38, R123– R152, 2005. 167. Hur, N., Park, S., Sharma, P. A., Ahn, J. S., Guha, S., and Cheong, S. W., Electric polarization reversal and memory in a multiferroic material induced by magnetic fields, Nature 429, 392–395, 2004. 168. Kimura, T., Lawes, G., and Ramirez, A. P., Electric polarization rotation in a hexaferrite with long-wavelength magnetic structures, Phys. Rev. Lett. 94 (13), 137201, 2005. 169. Lottermoser, T., Lonkai, T., Amann, U., Hohlwein, D., Ihringer, J., and Fiebig, M., Magnetic phase control by an electric field, Nature 430, 541–544, 2004. 170. Souchkov, A. B., Simpson, J. R., Quijada, M., Ishibashi, H., Hur, N., Ahn, J. S., Cheong, S.-W., Millis, A. J., and Drew, H. D., Exchange interaction effects on the optical properties of LuMnO3, Phys. Rev. Lett. 91, 027203, 2003. 171. Spaldin, N. A., and Fiebig, M., The renaissance of magnetoelectric multiferroics, Science 309, 391–392, 2005. 172. Pimenov, A., Mukhin, A. A., Ivanov, V. Y., Travkin, V. D., Balbashov, A. M., and Loidl, A., Possible evidence for electromagnons in multiferroic manganites, Nature Physics 2, 97–100, 2006. 173. Axt, V. M., and Kuhn, T., Femtosecond spectroscopy in semiconductors: a key to coherences, correlations, and quantum kinetics, Rep. Prog. Phys. 67, 433–512, 2004.
7525_C004.indd 169
11/15/07 11:10:07 AM
7525_C004.indd 170
11/15/07 11:10:07 AM
5
Time-Resolved Terahertz Studies of Conductivity Processes in Novel Electronic Materials Jie Shan
Case Western Reserve University
Susan L. Dexheimer
Washington State University
Contents 5.1 Introduction................................................................................................... 172 5.2 Charge Transport in Photo-Excited Insulators: Polarons in Single-Crystal Sapphire............................................................................ 173 5.3 Charge Transport in Disordered Electronic Materials: Dispersive Transport in Amorphous Semiconductors and Semiconducting Organic Polymers.......................................................................................... 176 5.3.1 Amorphous Semiconductors............................................................. 177 5.3.2 Semiconducting Organic Polymers.................................................. 182 5.4 Polaron Formation and Dynamics in Molecular Electronic Materials......... 184 5.4.1 Dynamics of Polaron Formation: Quasi-One-Dimensional Systems............................................................................................. 185 5.4.2 Carrier Transport in Pentacene......................................................... 187 5.5 Charge Transport in Nanoscale Materials: Nanocrystalline Semiconductors and Quantum Dots............................................................. 188 5.5.1 Conductivity and Dielectric Screening in Nanoporous TiO2........... 189 5.5.2 Excitons in Semiconductor Quantum Dots...................................... 190 5.6 Extending into Mid-Infrared Spectral Regime: Carrier Dynamics in Graphite...................................................................... 193 5.7 Summary....................................................................................................... 196 Acknowledgments................................................................................................... 196 References............................................................................................................... 196
171
7525_C005.indd 171
11/19/07 10:27:57 AM
172
Terahertz Spectroscopy: Principles and Applications
5.1 Introduction Terahertz (THz) spectroscopy based on femtosecond laser techniques1–12 has emerged as a powerful probe of charge transport and carrier dynamics. The technique makes use of ultrashort pulses of propagating electromagnetic radiation to measure conductivity in the THz spectral regime. (A frequency of 1 THz = 1012 Hz, and corresponds to an energy of 4.2 meV = 33 cm-1 = 48 K and a wavelength of 300 mm.) In particular, when combined with a time-synchronized femtosecond excitation pulse, THz spectroscopy is suitable for the investigation of electronic charge transport under nonequilibrium conditions.13–17 These attributes permit THz spectroscopy to circumvent many of the constraints of conventional transport measurement techniques. Conventional electrical characterization techniques do not generally allow access to material response at frequencies as high as those of carrier-scattering processes, information that is of great value in examining the fundamentals of charge transport mechanisms, and are not suited for probing very rapid changes in the material response, so that they typically cannot explore the interesting and important regime of nonequilibrium electronic excitation. In addition, in conventional measurements of charge transport, one must have samples amenable to good electrical contact, an issue that can be a severe constraint, especially in studies of nanoscale materials. The THz probing technique, used in conjunction with optical pump excitation, can overcome all of these limitations. In this chapter, we describe the application of this approach to studies of the a number of aspects of fundamental properties of charge transport in novel electronic materials and highlight new insights into the properties and dynamics of charge carriers that have resulted from the distinctive measurement capabilities of time-resolved THz spectroscopy. We focus in particular on carrier dynamics made accessible by recent ultrafast time-resolved techniques; measurements of steady-state properties in this important spectral region using both recently developed time-domain THz and well-established far-infrared/submillimeter techniques have been applied in a wide range of studies of materials, as reviewed extensively elsewhere.1–12 In Section 5.2, we discuss time-resolved THz studies of charge transport in insulators. Unlike in metals and semiconductors, because of difficulties in doping or thermally exciting the system, charge carriers are often present only under nonequilibrium conditions. Insulators, therefore, provide an ideal laboratory to demonstrate the unique capabilities of time-resolved THz spectroscopy. In addition, the subpicosecond timescale of the probe electric field transient implies that we have access to frequencies up to the THz range, frequencies comparable to charge carrier scattering rates in typical crystalline materials or transfer rates between neighboring sites in disordered systems. In Section 5.3, we present examples of how THz spectroscopy can yield important information about charge transport in disordered electronic materials, focusing in particular on dispersive transport in amorphous semiconductors and photoconducting polymers. The short-pulse nature of the THz probe also implies that we have access to the dynamics of rapidly evolving systems. In Section 5.4, we describe time-resolved THz studies of fast photocarrier dynamics in molecular electronic materials, including studies of the dynamics of polaron formation in quasi-one-dimensional systems and of photoconductivity in molecular crystals. Since the THz measurements are made with traveling electromagnetic waves,
7525_C005.indd 172
11/19/07 10:27:57 AM
Time-Resolved Terahertz Studies of Conductivity Processes
173
no electrical contacts are needed. In Section 5.5, we describe how one can take advantage of this property to perform measurements of nanoscale materials, systems for which formation of electrical contacts may be difficult and, further, may significantly modify the properties of the material. Finally in Section 5.6, we indicate how the technique of THz spectroscopy can be extended from the far-infrared to the mid-infrared regime and can be used to obtain both amplitude and phase information about material response in this spectral regime after photoexcitation. These ultrabroadband THz sources can also provide pulse durations well below 100 fs, permitting higher time resolution for probing ultrafast processes. Studies of the impact of strongly coupled optical phonons on the electronic charge transport properties in graphite provide an example of this approach. The aim of this chapter is to provide an overview of the diverse applications of time-resolved THz spectroscopy for probing the properties of electronic materials.13–79 Given the extensive literature that has emerged over the past several years based on this powerful experimental methodology, we do not attempt to be comprehensive in our review, but rather to select representative studies that highlight the capabilities of the method and the range of its application. We focus in particular on novel electronic materials in which time-resolved THz spectroscopy has provided new insight into conductivity mechanisms. Time-resolved THz spectroscopy is also especially well-suited for studies of carrier dynamics in conventional semiconductors, superconductors, and strongly correlated electronic materials, as discussed in detail in the chapter by Kaindl and Averitt in this book. The instrumentation and experimental techniques for the time-resolved THz measurements are discussed in detail in the first part of this volume.
5.2 Charge Transport in Photo-Excited Insulators: Polarons in Single-Crystal Sapphire The nature of charge transport in normally insulating solids or liquids is a subject of considerable technologic and fundamental importance. From the technological standpoint, understanding of electronic transport in insulators is crucial for important processes such as electrical and optical breakdown, as well as for their use as radiation detectors. From the basic physics viewpoint, there is inherent interest in being able to examine charge transport in insulators, just as has been done comprehensively in metals and semiconductors. Of particular significance is the role of polarons in ionic insulators. Because of the strong interaction between conduction electrons and phonons in such ionic materials, electrons are surrounded by a cloud of virtual phonons, forming quasiparticles called polarons. Polaronic transport in various regimes, depending on the electron–phonon interaction strength, has been a subject of much theoretical attention. However, as mentioned previously, unlike in metals and semiconductors, charge carriers typically exist in insulators only under nonequilibrium conditions and are not accessible to conventional electrical characterization techniques. Conventional approaches are further impeded by the difficulty of making electrical contacts to insulators and the short lifetime of the carriers prior to trapping or recombination. THz spectroscopy, combined with ultrafast optical excitation, opens up new possibilities to investigate charge transport in insulators.
7525_C005.indd 173
11/19/07 10:27:58 AM
174
Terahertz Spectroscopy: Principles and Applications
Recently, model systems including a variety of insulating liquids53,54 and solids such as single-crystal sapphire (Al2O3)74 and rutile (TiO2)34 have been studied. We use the example of single-crystal sapphire74 to illustrate the approach. In the measurements, conduction electrons were injected in sapphire (band gap Eg = 8.7 eV) through two-photon absorption of the third harmonic of a Ti:sapphire laser. The electric-field waveforms E(t) of THz pulses transmitted through the unexcited sapphire crystal and the pump-induced change in the THz waveform, ∆E(t), were recorded. A delay of several picoseconds after pump excitation was chosen to ensure that any hot carrier effects had abated, but that the carrier density had not decreased significantly. Figure 5.1(a) displays representative waveforms of E(t) and ∆E(t) measured for sapphire at room temperature. To extract the pump-induced complex dielectric function ∆ε(ν) or complex conductivity σ(n), as a function of the frequency n, we take the Fourier transforms of the measured THz waveforms. In the limit of a weak perturbation to the THz response, as is appropriate for the current experimental conditions, a linear relation between the pump-induced response and the ratio of the Fourier transform of the waveforms can be found -1
2 πnl ε( n) - ε ext ( n) ∆ E ( n) ∆ε( n) = 2 ε( n) i , × c / ε ( n ) ε ( n ) + ε ( n ) E ( n) extt
σ( n) = -2 πi nε 0 ∆ε( n). Here E(n) and ∆E(n) denote the Fourier transform of the corresponding time-domain quantities, E(t) and ∆E(t), ε0 is permittivity of free space, and ε(n), and εext(n) are the
0.6
E(t)
0 –100 1
σ´ and σ´´(1/Ωm)
Electric Field (a.u.)
100
∆E(t)
0 –1 0
1
2 Time (ps) (a)
3
σ´
0.3
0.0
σ´´
0.5
1.0 Frequency (THz) (b)
1.5
Figure 5.1 (a) Top panel: the transmitted THz electric-field waveform E(t) in single-crystal sapphire (Al2O3) at room temperature; bottom panel: pump-induced change in the THz waveform ∆E(t) (dots) and a fit to the Drude model (solid curve). The pump fluence was 3 J/m2 and the pump-probe delay was 5 ps. (b) Frequency dependence of the real (σ′) and the imaginary part (σ″) of the pump-induced complex conductivity (dots) of single-crystal sapphire at room temperature, extracted from the waveforms in (a). The solid curves represent a fit to the Drude model. (From Shan, J. et al., Phys. Rev. Lett. 90, 247401, 2003. With permission.)
7525_C005.indd 174
11/19/07 10:28:03 AM
Time-Resolved Terahertz Studies of Conductivity Processes
175
complex dielectric functions of the unperturbed sample and its surrounding material (e.g., air, sample cell windows), respectively. This expression includes propagation through the excited sample of thickness l, as well as interfacial transmission losses at the boundary of the sample. The influence of multiple reflections is slight and has been omitted for simplicity. The frequency-dependent complex conductivity, σ(n) = σ′(n) + iσ″(n), corresponding to the waveforms of Figure 5.1(a) is shown in Figure 5.1(b). It is dominated by the electron conductivity because of the much smaller value of the electron mass (and, correspondingly, the larger value of the electron mobility) than that of the hole. The experimental results (dots) are described satisfactorily by the simple Drude model for conductivity, σ( n) = ε 0 ω 2p /( γ 0 - 2 πi n), as shown by the solid lines. Here, γ0 denotes the electron scattering rate, and ωp = {ne2/(ε0 m*)}1/2 the plasma frequency, which is related to the density of conduction electrons (n), the elementary charge (e), and the electron effective mass (m*). The corresponding fit to the time domain data is shown in Figure 5.1(a) as a solid line. From the fitting procedure, a room-temperature scattering rate of γ0 = (95 fs) –1 and a plasma frequency of ωp = 2π × 0.15 THz were obtained. The fact that the frequency-dependent conductivity is adequately described by the Drude model indicates that conduction electrons form large polarons in sapphire, quasiparticles that remain mobile but exhibit an enhanced effective mass m* as they travel through the solid because of the electron-phonon interaction. A schematic representation of large polaron transport in ionic crystals is shown in Figure 5.2(a). This behavior contrasts with charge transport in nanostructures that exhibit strong quantum confinement effects and in disordered systems, as discussed in subsequent sections of this chapter. The nature of the charge transport can be further explored by examining the dependence of the conductivity on the sample temperature. With decreasing sample temperature, the conductivity retains its Drude form, but exhibits a sharply reduced scattering rate. As shown in Figure 5.3, the scattering rate drops from γ0 = (95 fs) –1 at room temperature to γ0 = (5 ps)–1 at 40 K, a decrease by a factor of approximately 50. An examination of the temperature dependence of γ0 reveals an activated behavior at high temperatures (T > 200 K) and a weaker variation at low temperatures (T < 200 K). These features are characteristic of LO phonon and acoustic phonon scattering, respectively. A comparison of the experimental findings with large polaron theories revealed important parameters characterizing electron–phonon interactions, as well as distinctions among the various theoretical models. The solid line in Figure 5.3 corresponds to a fit to the polaron model of Low and Pines80 with an effective electron mass of m* = 0.30 m 0 (the electron mass), and the dashed line represents only the acoustic phonon contribution to the total scattering rate. One particularly interesting result of this study is that the electron mobility in high-purity sapphire can be as high as 600 cm2/V⋅s at room temperature and that the mobility increases sharply with decreasing temperature. At 40 K, the electron mobility exceeds 10,000 cm2/V⋅s, a value normally associated with high-mobility semiconductors. Thus, at low temperatures, the complete freezing out of the LO phonons and the reduced interaction with acoustic phonons can lead to high carrier mobility in insulators having sufficiently low defect densities.
7525_C005.indd 175
11/19/07 10:28:06 AM
176
Terahertz Spectroscopy: Principles and Applications +
– +
+
–
+
–
+
–
+
+
–
+
–
–
–
+
–