Introduction to Circuit Analysis and Design
.
Tildon H. Glisson, Jr.
Introduction to Circuit Analysis and Design
Prof. T. H. Glisson, Jr. 3072 EB-II, Box 7911 N.C. State University Raleigh, NC 27695
[email protected]
The solution manual and other supplementary material are provided to those who are using or considering using the book as the textbook for a related course. To gain access to the solution manual and other supplementary material, go to http://www.springer.com/978-90-481-9442-1, click on the appropriate link under Additional Information on the right side of that page, and follow the instructions given there. ISBN: 978-90-481-9442-1
e-ISBN: 978-90-481-9443-8
DOI: 10.1007/978-90-481-9443-8 # Springer Science+Business Media B.V. 2011 No part of this work may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, microfilming, recording or otherwise, without written permission from the Publisher, with the exception of any material supplied specifically for the purpose of being entered and executed on a computer system, for exclusive use by the purchaser of the work. Printed on acid-free paper springer.com
To Andy Sage, Ben O’Neal, and Sy Matthews. Each knows why.
.
Preface
This book is intended as the textbook for a first course in electric circuits. It has evolved from notes that I developed over several years, while I taught the introductory circuits course to sophomore electrical- and computer-engineering students at North Carolina State University. As the chapter titles indicate, the major topics are those covered in almost all books of this kind. But selection and treatment of topics was guided not only by what is traditional for the target course, but also by the meaning and purpose of circuit analysis and (ultimately) design. This book reflects the views that circuit analysis is concerned primarily with finding and interpreting the relation a circuit establishes between excitation and response, that circuit design is concerned primarily with creating a circuit that enforces a specified relation between excitation and response, and that in design in particular, the devil is in the details. These perspectives led to somewhat different approaches to some aspects of the subject and to including some topics not treated in outwardly similar books. As a bonus, these topics give a practical flavor to and stimulate interest in some otherwise dry subjects. Compared with other books for the same audience, this book gives more attention to transfer functions, input and output impedance, and two-port models; to power dissipation and power transfer, topics whose importance in practice is far greater than their treatment in most books would suggest; to the physical origins of capacitance and inductance, so students can gain some understanding of the origins of stray, residual, and parasitic capacitance and inductance, and how consideration of such effects influences component selection and placement; and to other ways in which physical components differ from idealized components, such as variation of parameters with temperature and frequency. Treatment of op amps is not limited to the ideal model, but covers topics such as output swing, output current limit, slew rate, bias-current compensation, power dissipation, stability, and gain-bandwidth product, all of which are important in any practical design. One unfamiliar with these topics cannot understand an op-amp data sheet or intelligently select an op amp for any particular application. The book contains more than 1,100 problems and more than 800 examples. Many of the problems are assemblages of similar problems; for example, “find the input impedance and output impedance of each circuit in Fig. ___.” So there are really many more than 1,100 problems. There is an adequate number of problems calling for numerical answers, through which students can gain confidence. But consistent with the focus on excitation-response relations, most problems ask the student to obtain an expression for a quantity or a relation among quantities. Some problems go further, and ask for an analysis or discussion of the influence of one or more vii
viii
Preface
parameters on a relation of interest. There is an adequate number of design problems in which there are fewer specifications than free parameters, requiring students to exercise some judgment. Different instructors approach this subject in different but equally valid ways, so I will not presume to suggest a syllabus. I note only that the book contains ample material for a two-semester or three-quarter course, but can be used selectively in a one-semester or two-quarter course. Most chapters and the book as a whole are organized such that topics generally included in a one-semester course are covered first. The only prerequisite for successful study of this book is facility with differential and integral calculus. Some exposure to electricity and magnetism, such as provided by a freshman physics course, might be helpful, but is not required. Some problems require use of a mathematics package such as Matlab# or Mathcad#, and some require use of a simulation package such as Pspice# or Electronics Workbench#. Problems requiring computer assistance are identified by the symbol :. There is no preference for or attempt to teach any particular software package, and it is possible to avoid these requirements altogether by simply not assigning such problems. A companion website provides solutions to all exercises and errata and (for faculty members that adopt the book) solutions to all problems in the book, selected supplementary material, and a mechanism for submitting corrections, suggestions, and comments. I have many to thank for whatever is good about the book, and only myself to blame for everything else. Thanks to James Kang and Bruno Osorno for their helpful comments on an early draft; to Art Davis, John Hauser, S.C. Dutta Roy, Joel Trussell, and Gary Ybarra for their thorough and helpful reviews; to Chris Lunsford for his contributions to several chapters; to Hari Chandrasekar, Vinodh Kotipalli, Misha Kumar, Christina Lee, and Satish Naidu, all excellent graduate students who spent many hours proofreading the text and checking my solutions to examples, exercises, and problems; and to all the companies, publishers, and individuals that permitted me to use or adapt parts of their intellectual property. Thanks to Jeff Kahler of Nuhertz Technologies and Siegfried Linkwitz for allowing me to use several of their designs in examples and problems. Special thanks to Art Davis and John Hauser for many correspondences and discussions that helped clarify or otherwise refine my presentations of various topics. Special thanks also, to those at Springer: Mark de Jongh, Senior Publishing Editor for Electrical Engineering; Cindy Zitter, his Senior Assistant; and Project Manager R. Samuel Devanand, for being so capable and helpful. Raleigh, North Carolina
Tildon H. Glisson Jr.
Contents
1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.1 Electric Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1.2 How to Study This Book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.3 Dimensions and Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.4 Symbols and Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 1.5 Symbols Versus Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1.6 Presentation of Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 1.7 Approximations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.8 Precision and Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1.9 Engineering Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 1.10 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2
Current, Voltage, and Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 Charge and Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 Electric Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 Electric Potential and Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 Ohm’s Law and Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 Resistivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 Conductance and Conductivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 E Series, Tolerance, and Standard Resistance Values . . . . . . . . . . . . . . . 2.9 Resistor Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.10 Variation of Resistivity and Resistance with Temperature . . . . . . . . . . 2.11 American Wire Gauge (AWG) and Metric Wire Gauge (MWG) . . . 2.12 DC and AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.13 Skin Effect and Proximity Effect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.14 Concluding Remark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.15 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19 19 21 23 25 26 26 27 29 30 32 35 36 36 42 42
3
Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws . . . . . . . . . . 3.1 Schematics and Circuit Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.2 Conductors and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.3 Annotating Circuit Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.4 Series and Parallel Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.5 Open Circuits and Short Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 Basic Circuit Elements: Resistors and Independent Sources . . . . . . . . 3.7 Kirchhoff’s Current Law and Node Analysis . . . . . . . . . . . . . . . . . . . . . . . .
49 49 50 51 53 53 54 56 ix
x
Contents
3.8 3.9 3.10 3.11
Kirchhoff’s Voltage Law and Mesh Analysis . . . . . . . . . . . . . . . . . . . . . . . Voltage and Current Dividers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Superposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
62 66 66 69
4
Equivalent Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Terminal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 Equivalent Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.1 Resistors in Series Are Additive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.2 Conductances in Parallel Are Additive . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.3 Voltage Sources in Series Are Additive . . . . . . . . . . . . . . . . . . . . . . . . 4.2.4 Current Sources in Parallel Are Additive . . . . . . . . . . . . . . . . . . . . . . 4.2.5 Elements in Series Commute, as do Elements in Parallel . . . . . 4.2.6 Finding Equivalent Resistance Using a Known Source . . . . . . . . 4.2.7 Approximations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Source Transformations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4 The´venin and Norton Equivalent Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.5 Notation: Constant and Time-Varying Current and Voltage . . . . . . . . 4.6 Significance of Terminal Characteristics and Equivalence . . . . . . . . . . 4.7 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
83 83 85 85 85 87 88 88 89 90 91 93 100 101 101
5
Work and Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 Instantaneous Power and the Passive Sign Convention . . . . . . . . . . . . 5.2 Instantaneous Power Dissipated by a Resistor: Joule’s Law . . . . . . . 5.3 Conservation of Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.4 Peak Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 Available Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6 Time Averages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.7 Average Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.8 Root Mean Squared (RMS) Amplitude of a Current or Voltage . . . 5.9 Average Power Dissipated in a Resistive Load . . . . . . . . . . . . . . . . . . . . . 5.10 Summary: Power Relations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.11 Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.12 Measurement of RMS Amplitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.13 Dissipation Derating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.14 Power Dissipation in Physical Components and Circuits . . . . . . . . . . 5.15 Active and Passive Devices, Loads, and Circuits . . . . . . . . . . . . . . . . . . . 5.16 Power Transfer and Power Transfer Efficiency . . . . . . . . . . . . . . . . . . . . . 5.17 Superposition of Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.18 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
113 114 116 119 120 122 123 126 130 131 133 133 133 135 139 141 142 147 148
6
Dependent Sources and Unilateral Two-Port Circuits . . . . . . . . . . . . . . . . 6.1 Input Resistance and Output Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Dependent Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.3 Linear Two-Port Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 Two-Ports in Cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 Voltage, Current, and Power Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.6 Transfer Characteristics, Transfer Ratios, and Gain . . . . . . . . . . . . . . . . . 6.7 Power Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
163 164 166 172 174 174 178 183
Contents
xi
6.8 Gains and Relative Values in Decibels (dB) . . . . . . . . . . . . . . . . . . . . . . . . 184 6.9 Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 186 6.10 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 187 7
Operational Amplifiers I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 Operational Amplifier Terminals and Voltage Reference . . . . . . . . . . 7.2 DC Circuit Model for an Op Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 The Ideal Op Amp and Some Basic Op-Amp Circuits at DC . . . . . . 7.4 Feedback and Stability of Op-Amp Circuits . . . . . . . . . . . . . . . . . . . . . . . . 7.5 Input Resistance and Output Resistance of Op-Amp Circuits . . . . . . 7.6 Properties of Common Op-Amp Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6.1 Inverting Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6.2 Non-inverting Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.6.3 Voltage Follower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.7 Op Amp Structure and Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.8 Output Current Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9 Input Offset Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.10 Input Bias Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.11 Power Dissipation in Op Amps and Op-Amp Circuits . . . . . . . . . . . . . 7.12 Design Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.13 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
197 199 200 202 207 210 213 213 214 214 216 216 216 217 219 222 224
8
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.2 Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.3 Terminal Characteristics of an Ideal Capacitor . . . . . . . . . . . . . . . . . . . . . 8.4 Charge-Discharge Time Constant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.5 Capacitors in Series and Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.6 Leakage Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.7 Stray and Parasitic Capacitance; Capacitive Coupling . . . . . . . . . . . . . 8.8 Variation of Capacitance with Temperature . . . . . . . . . . . . . . . . . . . . . . . . 8.9 Energy Storage and Power Dissipation in a Capacitor . . . . . . . . . . . . . 8.10 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10.1 Differentiating Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10.2 Integrating Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10.3 Bypass Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10.4 Bypass Capacitors (Filter Capacitors) in Rectifier Circuits . . . 8.10.5 Bypassing in Digital Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10.6 Coupling Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10.7 Input Bias Current Compensation in Capacitively Coupled Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10.8 Switched Capacitor Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.10.9 Power Dissipation in Switched-Capacitor Circuits . . . . . . . . . 8.11 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
237 237 239 242 246 252 253 255 258 260 262 262 263 266 268 270 271
Inductance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.1 Magnetic Field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.2 Self Inductance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.3 Inductance of Air-Core Coils . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
301 301 302 303
9
276 279 281 284
xii
Contents
9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 9.13 9.14 9.15 9.16
Inductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Terminal Characteristic of an Inductor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Time Constant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inductors in Series and Parallel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Energy Storage and Power dissipation in an Inductor . . . . . . . . . . . . . . Parasitic Self-Inductance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reducing Ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Inductive Kick . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Magnetically Coupled Coils and Mutual Inductance . . . . . . . . . . . . . . . Parasitic Mutual Inductance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ideal Transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Applications of Transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.16.1 Source and Load Transformations: Matching Transformers . . 9.16.2 Step-Up and Step-Down Transformers . . . . . . . . . . . . . . . . . . . . . 9.16.3 Isolation Transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.16.4 Center-Tapped Transformers and Balanced Power . . . . . . . . . 9.17 Concluding Remarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.18 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
304 305 307 312 313 314 316 318 319 323 324 326 328 328 330 331 332 333 334
10
Complex Arithmetic and Algebra . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1 Complex Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 Complex Arithmetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3 Conjugate of a Complex Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.4 Magnitude of a Complex Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.5 Arithmetic in a Complex Plane . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.6 Polar Form of a Complex Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.7 Eulers Identity and Polar Arithmetic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.8 The Symbols ∠ and ∡ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.9 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
345 345 345 346 347 347 348 349 351 351
11
Transient Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.1 Unit Step Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.3 Initial Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4 First-Order Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5 Second-Order Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5.1 Summary: Second-Order Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5.2 Dominant Time Constant (or Characteristic Root) . . . . . . . . . 11.5.3 Damping Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.5.4 Extrema of the Unforced Component of an Underdamped Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.6 Time Invariance, Superposition, and Pulse Response . . . . . . . . . . . . . . 11.7 Operator Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.8 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
353 353 354 354 355 360 365 369 370
12
371 373 375 377
Sinusoids, Phasors, and Impedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 12.1 Sinusoidal Voltages and Currents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 12.2 Time Origin, Phase Reference, and Initial Phase . . . . . . . . . . . . . . . . . . . 385
Contents
xiii
12.3 12.4 12.5 12.6 12.7 12.8 12.9 12.10 12.11 12.12 12.13 12.14 12.15 12.16 12.17
Phasors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Phasor Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Impedance and Generalized Ohm’s Law . . . . . . . . . . . . . . . . . . . . . . . . . . Admittance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Impedance and Admittance Ratios in dB . . . . . . . . . . . . . . . . . . . . . . . . . . A Fundamental Relation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Circuit Reduction: Elements in Series and Parallel . . . . . . . . . . . . . . . Time Domain and Frequency Domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sinusoidal and DC Steady State . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Frequency-Domain Circuit Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reactance and Effective Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Susceptance and Effective Conductance . . . . . . . . . . . . . . . . . . . . . . . . . . Impedance and Admittance Triangles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Linearity and Superposition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The´venin and Norton Equivalent Circuits: Source Transformations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Checking Your Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Resonance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Quality Factors and Common Resonant Configurations . . . . . . . . . . Simulating Inductance Using Active RC Circuits . . . . . . . . . . . . . . . . . Circuit Elements and Physical Circuit Components . . . . . . . . . . . . . . . 12.22.1 Resistors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.22.2 Inductors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12.22.3 Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
388 390 391 395 396 397 399 402 404 405 407 412 414 414
13
Complex Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.1 Definition of Complex Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.2 Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.3 Power Calculations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.4 Reactive Power and Apparent Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.5 Conservation of Complex Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.6 Power Relations in Resonant Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.7 Power Factor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.8 Power Triangle and Power-Factor Correction . . . . . . . . . . . . . . . . . . . . . 13.9 Superposition of Complex Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.10 Power Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.10.1 Power Transfer Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.10.2 Power Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.10.3 Insertion Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.11 Impedance Matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.11.1 Transformers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.11.2 L Sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13.12 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
479 479 481 482 483 486 487 489 491 496 496 497 500 503 504 504 506 510
14
Three-Phase Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.1 Three-Phase Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.2 Power Transmission and Distribution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.3 Residential Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
521 521 523 524
12.18 12.19 12.20 12.21 12.22
12.23
421 431 435 438 444 447 448 451 453 456
xiv
Contents
14.4 14.5 14.6 14.7 14.8 14.9
Three-Phase Loads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Balanced Y–D and D–Y Load Transformations . . . . . . . . . . . . . . . . . . . . Power Calculations for Balanced Three-Phase Loads . . . . . . . . . . . . . . Power-Factor Correction for Three-Phase Loads . . . . . . . . . . . . . . . . . . . Instantaneous Power Delivered to a Balanced Load . . . . . . . . . . . . . . . . Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
524 528 530 531 534 535
15
Transfer Functions and Frequency-Domain Analysis . . . . . . . . . . . . . . . . 15.1 Transfer Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.2 Dependence of a Transfer Function upon Source and Load . . . . . . 15.3 Gain and Phase Shift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.4 Gain in Decibels (dB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.5 Standard Form of a Transfer Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.6 Asymptotic Gain Plots: Linear Factors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.7 Asymptotic Gain Plots: Quadratic Factors . . . . . . . . . . . . . . . . . . . . . . . . 15.8 Asymptotic Plots of Phase Shift Versus Frequency . . . . . . . . . . . . . . . 15.9 Filters and Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.10 Frequency Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.11 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
539 539 544 545 546 550 555 562 565 569 572 573
16
Fourier Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.1 Amplitude–Phase Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.2 Exponential Series and Fourier Coefficients . . . . . . . . . . . . . . . . . . . . . . 16.3 Quadrature Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.4 Summary: Three Forms of Fourier Series . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 Integral Formula for Fourier Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . 16.6 A Table of Fourier Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.7 Modified Fourier Coefficients for Composite Waveforms . . . . . . . . 16.8 Convergence of Fourier Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.9 Gibbs’ Phenomenon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.10 Circuit Response to Periodic Excitation . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.11 Spectra and Spectral Analysis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.12 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
583 583 585 586 587 588 590 595 597 599 600 603 605
17
Operational Amplifiers II: AC Model and Applications . . . . . . . . . . . . . . 17.1 AC Model for an Op Amp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.2 Linear Resistive-Feedback Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.3 Linear Reactive-Feedback Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.4 Output Swing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.5 Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.6 Amplifiers in Cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.7 Capacitance Coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.8 Input Bias Current Compensation in Capacitance-Coupled Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.9 Power Dissipation in Op Amps and Op-Amp Circuits . . . . . . . . . . . . 17.10 Power-Conversion Efficiency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.11 Op-Amp Amplifier Circuit Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17.12 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
609 609 611 617 619 621 624 626 627 628 632 633 642
Contents
xv
18
19
Laplace Transformation and s-Domain Circuit Analysis . . . . . . . . . . . . . 18.1 Definition of the Laplace Transformation . . . . . . . . . . . . . . . . . . . . . . . . . 18.2 Convergence and Uniqueness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.3 One-Sided Laplace Transforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.4 Shorthand Notation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.5 The Delta Function (Unit Impulse) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.6 Tables of Operational Properties and Transform Pairs . . . . . . . . . . . . 18.7 Inverse Transforms Using Partial-Fraction Expansions . . . . . . . . . . . 18.7.1 Distinct Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.7.2 Complex-Conjugate Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.7.3 Repeated Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.8 Terminal Characteristics and Equivalent Circuits . . . . . . . . . . . . . . . . . 18.9 Circuit Analysis in the s Domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.10 Checking Your Work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.11 s-Domain Transfer Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.12 Forced Response and Unforced Response . . . . . . . . . . . . . . . . . . . . . . . . . 18.13 Impulse Response and Step Response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.14 Relation of s-Domain to Frequency-Domain Transfer Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.15 s-Domain Models for Op Amps and Basic Op-Amp Circuits . . . . . 18.16 Circuits in Cascade . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.17 Poles, Zeros, and Pole-Zero Plots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.18 Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.19 Pole-Zero Cancellation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.20 Dominant Poles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.21 Pole-Zero Plots and Bode Plots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18.22 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
653 653 655 657 657 657 659 663 664 665 667 669 670 675 678 683 684
Active Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.1 Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.2 Group Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.3 A Simple Two-Pole Active Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.4 Sallen-Key (VCVS) Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.5 State-Variable Biquadratic Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.6 Modern Filter Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.6.1 VCVS Butterworth Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.6.2 VCVS Bessel Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.6.3 VCVS Chebyshev Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.7 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
723 723 724 725 727 732 736 736 738 739 741
689 689 691 692 694 697 697 700 703
Appendix: Answers to Exercises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 745 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 759
.
Chapter 1
Introduction
Electrical engineering is among the largest and most diverse professions. The Institute of Electrical and Electronic Engineering (IEEE), which is the principal technical and professional organization for electrical engineers, is the largest professional organization in the world. Within the IEEE alone, there are more than 40 technical societies, each focused on a sub-area of electrical engineering. These are listed in Table 1.1. Electrical engineers are employed in every major industry, working not only with other electrical engineers, but also with people from all walks of life. Their work ranges from very applied to highly theoretical. They work indoors and out, in government and in private industry, alone and in large groups. They contribute to the design and manufacture of virtually every product you can name. In short, almost anyone inclined toward engineering can find an exciting, fulfilling, and rewarding career in electrical engineering. You have chosen well.
1.1 Electric Circuits The one thing that almost all electrical engineers have in common is the fact that they design, manufacture, maintain, teach about, or sell devices, equipment, or systems whose operation depends primarily upon manipulation of electricity. In such systems, electricity is the primary means for conveying or converting energy, transmitting or processing data, monitoring or controlling other equipment or processes, or measuring or observing various phenomena. Manipulating electricity toward useful ends is what circuits are all about. Thus it is no accident that almost all introductory EE courses and textbooks focus on circuits.
In the broadest sense, a circuit is something that makes electricity do something useful. Circuits in computers use electricity to store, retrieve, transmit, and process data at unimaginable speed. Circuits deliver tremendous quantities of electrical energy to our homes and industries at bargain-basement prices. Circuits allow us to transmit and receive hundreds of radio and TV programs. Circuits make our automobiles run cleaner and more efficiently. They help us store and prepare our food, wash our clothes, and cool our homes. They help aircraft, ships, and space shuttles navigate. They help us defend our borders and warn us of impending danger. They help monitor and predict the weather and help physicians monitor our health and perhaps save our lives. It is difficult to think of anything we do in which we are not assisted by one or more electric circuits. Certainly there are other important subjects in EE, but without circuits, most of those subjects would either not exist or have no practical application. We might be able to imagine a world without circuits, but few of us would want to live there. All in all, study of circuits is an excellent way to begin study of electrical engineering. The principal quantities of interest in circuit analysis and design are current, voltage, and power, none of which is visible.1 For the most part, not even the effects of currents and voltages in the innards of a circuit are visible. Indeed, without a powerful microscope, we cannot even see the innards of many modern circuits. We must rely on measurements and mathematics to tell us whether a circuit is working as it should. Thus it might appear that circuit analysis and
1
Current in an arc is visible, but unless we are designing an electric welder, we usually try to avoid arcs.
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_1, # Springer ScienceþBusiness Media B.V. 2011
1
2 Table 1.1 IEEE technical societies IEEE Aerospace and Electronic Systems Society IEEE Antennas and Propagation Society IEEE Broadcast Technology Society IEEE Circuits and Systems Society IEEE Communications Society IEEE Components Packaging, and Manufacturing Technology Society IEEE Computational Intelligence Society IEEE Computer Society IEEE Consumer Electronics Society IEEE Control Systems Society IEEE Council on Superconductivity IEEE Dielectrics and Electrical Insulation Society IEEE Education Society IEEE Electromagnetic Compatibility Society IEEE Electron Devices Society IEEE Engineering Management Society IEEE Engineering in Medicine and Biology Society IEEE Geoscience & Remote Sensing Society IEEE Industrial Electronics Society IEEE Industry Applications Society IEEE Information Theory Society IEEE Intelligent Transportation Systems Society
design is inherently more abstract than, for example, mechanism analysis and design. We can see mechanisms operate, whereas most electric circuits look the same whether operating or not. Unless something is seriously wrong, the components of a circuit do not jump about, make clanking noises, emit smoke, or squirt messy fluids here and there. But in truth, the level of abstraction of circuit analysis and design relative to that of other subjects is overstated. It is true that we cannot see current or voltage, but we cannot see force, pressure, or temperature, either. Nor can we see a mechanism we have not yet designed. Any extraordinary difficulties with circuits probably arise more from lack of familiarity than level of abstraction. Almost everyone has some intuitive understanding of fluid flow and pressure and the functions of pipes, pumps, and valves. But few laypersons have an equally well-developed intuition regarding current and voltage and the functions of circuit components such as resistors, transistors, and capacitors. In the beginning, analogies can be helpful. Current is flow of electric charge and is analogous to fluid flow (flow of molecules) in a hydraulic system. Voltage is analogous to pressure, in that voltage can cause current
1 Introduction
IEEE Instrumentation and Measurement Society IEEE Lasers & Electro-Optics Society IEEE Magnetics Society IEEE Microwave Theory and Techniques Society IEEE Nanotechnology Council IEEE Nuclear and Plasma Sciences Society IEEE Oceanic Engineering Society IEEE Photonics Society IEEE Power Electronics Society IEEE Power and Energy Society IEEE Product Safety Engineering Society IEEE Professional Communication Society IEEE Reliability Society IEEE Robotics & Automation Society IEEE Sensors Council IEEE Signal Processing Society IEEE Society on Social Implications of Technology IEEE Solid-State Circuits Society IEEE Systems, Man, and Cybernetics Society IEEE Ultrasonics, Ferroelectrics, and Frequency Control Society IEEE Vehicular Technology Society
in a wire, much like pressure can cause fluid flow in a pipe. Circuit components and circuits themselves are described in terms of the current-voltage relationships they establish at their terminals, just as hydraulic components are described in terms of flow and pressure at their terminals (inlets and outlets); for example, a pump can be described by the flow it can provide at one or more pressures (e.g., 3 gal/min at 100 lb/in.2) and a generator can be described by the current it can provide at the specified terminal voltage (e.g., 50 A at 120 V). If we know the flow-pressure characteristics of each component in a hydraulic system, we can calculate flow and pressure anywhere in the system. Likewise, if we know the current-voltage characteristics of each component in a circuit, we can calculate current and voltage anywhere in the circuit. Although analogies can be helpful, they also can be misleading if carried too far. There are circuits and devices in which current does not behave like fluid flow. Also, circuits can do many things that hydraulic systems cannot (and vice versa), in which case there is no analogy to fall back on. Ultimately, if we are to design circuits, we must come to understand current, voltage, and circuits on their own terms.
1.2 How to Study This Book
When you have mastered the material presented in this book, you will have a basic understanding of what current and voltage are and how they behave. You will be able to analyze and design a number of basic (but important) kinds of circuits. You will have accumulated a repertoire of physical laws and mathematical procedures that are essential in study of more advanced circuits and systems for communication, control, computing, and other applications. You will have begun to speak the language of electrical engineering, which is the first step toward becoming an electrical engineer and enjoying a challenging and rewarding career.
3
• Physical laws prescribe relations among defined quantities; for example, in circuits, important physical laws are Ohm’s law and Kirchhoff’s laws. • Derived results are important relations among the defined quantities that are obtained using physical laws, definitions, and mathematics; The´venin’s theorem (Chapter 4) is an example of an important derived result. • Computational procedures systematically use physical laws, derived results, and mathematics to solve problems (e.g., to analyze or design circuits). Examples are the node-voltage and mesh-current methods for finding voltages and currents in circuits.
1.2 How to Study This Book Because this is presumably one of your first engineering courses, you might be receptive to some advice about how to study an engineering subject – and this book, in particular. Most engineering subjects have pretty much the same anatomy, illustrated by Fig. 1.1: • At the core are (usually very few) undefined quantities; for example, time and charge, and essential properties of those quantities.2 • Next are definitions. These include definitions of important quantities, such as current and voltage, in terms of the core undefined quantities. Also included here are important symbols, terminology, and notation associated with the subject.
Undefined Quantities Definitions Physical Laws Derived Results Computational Procedures
Fig. 1.1 Anatomy of a technical subject
As you make your way through this book, note whether each new thing you encounter as a definition, a law, a derived result, or a procedure. Establish in your mind the relation of the new thing to things learned previously. • You should memorize each definition, when it is first encountered, before proceeding. If you do not, chances are you will have difficulty understanding subsequent text, derivations, and examples. Definitions are given for a reason, the reason being frequent subsequent use of the thing defined. Special symbols comprise an important class of defined terms and also should be memorized; for example, in this book the letters i and v always stand for current and voltage, respectively. Certain dimensions and units also are defined quantities and must be committed to memory. • You must also memorize physical laws, because they do not necessarily follow from anything else presented in this book.3 Fortunately, there are relatively few laws to be memorized. • Derived results are obtained using definitions, laws, limiting assumptions, and other derived results. You should be sure you understand important limiting assumptions before proceeding. In almost all subjects, there are many more derived results than physical laws. Your teacher can guide you regarding which derived results you should memorize and which you should be able to derive, yourself, possibly under slightly different conditions.
2
The essential property of time is perhaps best captured by Yogi Berra’s definition: “Time is what keeps everything from happening all at once.” The essential properties of charge are given in Chapter 2.
3
One subject’s laws can be another subject’s derived results; for example, Ohm’s law (a law in circuits courses) is a derived result in some more fundamental courses.
4
1 Introduction
• A procedure is essentially a recipe for solving a class of problems, based upon certain laws and derived results. The class of problems to which a procedure can be applied is defined by the conditions under which the underlying laws and derived results apply. For example, mesh analysis, which is a procedure for finding voltages and currents in a circuit, is based upon Kirchhoff’s voltage law, which in turn is applicable only under certain restrictions on the natures (e.g., wavelengths) of the voltages and currents applied to the circuit.
If you can do all that, you can be confident that you have a good grasp of the material. The only thing left to do is to hone your skills through practice; e.g., by reworking homework problems and other problems that are like those your teacher assigned or recommended. As you work through examples and problems, attempt to discern what definitions, laws, derived results, and procedures the example or problem is intended to reinforce.
1.3 Dimensions and Units Exercise 1.1. Recall from your study of physics that electric charge is conserved. In absence of any further information, would you regard this claim as a definition, a physical law, or a derived result? Viewing the content of a subject in the manner illustrated by Fig. 1.1 can help you organize your notes and thinking, especially at the end, when you are preparing for a final examination. From the outset, it can help you plan your outline and identify what is truly important or general and what is less important or specific as you proceed through the text. Before each exam, for example, you might be sure that you can answer the following questions: • What quantities have been defined or described and what are the definitions or defining properties? Include symbols, terms, and basic units. • What fundamental laws have been presented and what relations do they establish among defined quantities? • What derived results have been obtained and under what conditions do they apply? What are the dimensions and units of derived quantities and how are they related to the dimensions and units of quantities defined or derived previously? What laws and mathematical operations are needed to derive the results? • What procedures have been presented and under what conditions are they useful? What laws, derived results, and mathematical operations do they use? • What is a paradigm example4 for each law, derived result, and procedure? 4
A paradigm example is one that illustrates application of a law, derived result, or procedure in the simplest possible setting, uncluttered by need for other laws, results, or procedures.
A quantity is something that is quantifiable; i.e., something that can be counted, measured, or calculated. In everyday life and especially in engineering and science, we deal with many different quantities; for example, time, length, weight, temperature, pressure, speed, area, and cost. A quantity has a numerical value and a dimension and is expressed by a number and a unit. Both the numerical value and the unit are necessary. One dollar and 1 yen have the same numerical value (one) but have quite different values in the marketplace. A quantity can be expressed in various units; for example, length can be expressed in inches, meters, miles, furlongs, yards, angstroms, rods, light-years, and other units. No matter how it is expressed, length remains length. Length is what is being measured or specified. The unit describes how (on what scale) length is expressed. Length is a dimension and the meter is a unit of length. Similarly, time is a dimension and the second is a unit of time. Exercise 1.2. Which of the following are quantities (dimensioned or dimensionless), which are units, and which are neither? (a) Time, (b) centrifugal force, (c) electron-volt, (d) Newtonmeter, (e) light-year, (f) age, (g) checking account balance, (h) purple, (i) longitude, (j) relative humidity, (k) north pole, (l) virtue, (m) valor, (n) micron. There are many different quantities, but only seven basic dimensions (basic quantities). The dimensions of all other known quantities can be expressed in terms of these seven and are called derived dimensions.
1.3 Dimensions and Units
Derived dimensions and units also are called compound dimensions and compound units because they are products and quotients of basic dimensions and units; for example, the dimension of area is length squared and the dimension of speed is length/time. The dimensions of area and speed are derived (compound) dimensions. Choosing the seven basic dimensions, the associated basic units, and names of units for important derived quantities establishes a system of units. The official system of units for engineering and science is the SI system,5 which was adopted by a number of very important people at a long meeting in Paris in 1960. In the SI system, the seven basic dimensions are length, time, mass, electric current, temperature, amount of substance, and luminous intensity.6 So far as we know, none of the seven can be expressed in terms of the other six. Of the seven basic quantities, only five are used in this book. These five and the associated SI units are given in Table 1.2. Note that electric current is the basic electrical quantity in the SI system. Electric charge would serve as well, and because current in a circuit is flow of charge (charge per unit time), charge would seem to be the more logical choice. But there is a good reason for choosing current, rather than charge, as a fundamental quantity. It turns out that there are two kinds of current: Conduction current, which is flow of charge, and displacement current, which can exist where no charge is present, as in a time-varying electromagnetic field (e.g., a radio wave). Table 1.2 Basic SI quantities and units Quantity (basic dimension) Name of SI unit SI abbreviation (symbol) for unit Length Meter m Time Second s Mass Kilogram kg Electric current Ampere A Temperature Kelvin K
5
SI System is redundant, because SI stands for Systeme Internationale, which (obviously) is French for international system. Nonetheless, “the SI system” is what everyone calls it. 6 Actually, which seven dimensions are defined as basic is a matter of choice. Any seven independent dimensions would do, but history and common sense have ruled in favor of the seven given here. There is much wider agreement on which seven quantities are basic than on the standard units for those seven.
5
Thus, from an engineering perspective, current appears to be a more basic quantity than charge. In any particular discipline, many quantities of interest are derived quantities; for example, in EE, we deal not only with current and time, but also with voltage, work (or energy), power, and many other quantities. Repeated use of compound units for all these quantities, such as kg m2 s2 for energy, is cumbersome. Compound units for important derived quantities are given their own names, most of which are chosen in honor of great engineers or scientists somehow associated with the quantity. Table 1.3 gives the names, symbols, and SI units for quantities (both basic and derived) used in this book, in alphabetical order. Table 1.3 also gives compound equivalents for derived units. Compound equivalents are useful in checking expressions for dimensional correctness (see below). Quantities used only occasionally in this book are not included in the table but are defined and discussed appropriately where they are introduced. There are two kinds of dimensionless quantities: (1) Those whose definitions do not involve any dimensioned quantities, such as atomic number and valence; and (2) those defined in terms of dimensioned quantities, but in such a way that all of the basic units involved cancel, such as the fine-structure constant and an angle. We use angles extensively in this book, so a little discussion of their nature is in order. Fundamentally, an angle is the quotient of two lengths (arc length/radius). The dimensions of length cancel from the quotient, so an angle is dimensionless (the compound unit of an angle is unity). Most dimensionless quantities are expressed without units. Angles are exceptions because an angle can be specified in either radians (rad) or degrees (deg), where p rad ¼ 180 deg. Although dimensionless, radians and degrees are different scales of measurement. In absence of any prior agreement, we must attach the correct one of those units to the numerical specification of an angle. Except in Chapter 14, we specify angles in radians, so we do not attach the dimensionless unit rad to any such specification. In this book, specifying an angle as (e.g.) y ¼ 1:47 means y ¼ 1:47 radians.
Exercise 1.3. Give a simpler unit for each of the following: (a) J s–1, (b) V A s, (c) C s–1, (d) A2 O, (e) O H F2 s2 , (f) kg m2 s2 .
6
1 Introduction
Table 1.3 Symbols and SI units. Names of basic dimensions are in bold type Quantity Symbol(s) SI unit (symbol) Admittance Y siemen (S) Angle y, f, a, b, F, Y radian (rad) Angular frequency o radians per second (rad/s) Capacitance C farad (F) Charge q coulomb (C) Complex frequency s radians per second (rad/s) Complex power S volt·ampere (VA) Conductance G, g siemens (S) Conductivity s siemens per meter (S m1) Current i, I ampere (A) Distance or length x, y, z, h, d, l meter (m) Electric potential F volt (V) Electric field strength E newtons per coulomb or volts per meter Energy w joule (J) Force f, F newton (N) Frequency f hertz (Hz) Impedance Z ohm (O) Inductance L henry (H) Magnetic flux f weber (Wb) Mass m kilogram (kg) Period or interval T second (s) Permeability m henries per meter (H m1) Permittivity e farads per meter (F m1) Pole p radians per second Power p, P watt (W) Reactance X ohm (O) Reactive power Q volt ampere reactive (VAR) Resistance R, r ohm (O) Resistivity r ohm meter (O m) Speed or velocity u meters per second (m s1) Susceptance B siemen (S) Temperature T kelvin (K) Time t second (s) Time constant t second (s) Voltage v,V volt (V) Work w joule (J) Zero z radians per second
There are several important conventions and rules regarding dimensioned quantities: • The symbol for a quantity stands for both the numerical value and the associated unit, as in x ¼ 10 m and t ¼ 5 s. Constructions such as “x meters” and “t seconds” are redundant. • Reserved symbols for quantities (e.g., t for time) carry subscripts where more than one such quantity is of interest. For example, times at which various events occur in a circuit might be designated t0, t1, t2, and so on. The presence of a subscript does not alter the dimension or unit of a quantity.
Equivalent unit(s) O1, A V1 None s1 AsV1 : CV1 A·s s1 J s1, W O1, A V1 ðOmÞ1 Basic dimension; Cs1 ; VO1 Basic dimension J C1 NC1 or Vm1 V C, N m, W s kg m s2, V C m1 s1 V A1 V s A1 ; WbA1 Vs Basic dimension S V s A1 m1 A s V1 m1 s1 J s1, V A V A1 J s1, V A, W V A1 V A1 m m s1 O1, A V1 Basic dimension Basic dimension S J C1, A O V C, N m, W s s
• Terms that are equated, compared (using < or >), added, or subtracted must have the same dimension and, if numerical, must be expressed in the same unit. • In particular, all equations must be dimensionally homogeneous; that is, all terms in an equation must have the same dimension. • The dimension of the product of quantities is the product of the dimensions of the quantities. • The dimension of the quotient of quantities is the quotient of the dimensions of the quantities. The quotient of like quantities is dimensionless.
1.3 Dimensions and Units
• The dimension of a differential is that of the associated variable; e.g., the dimension of dt is that of t. • Dimensionally, a derivative is a quotient and an integral is a product; e.g., the dimension of dq/dt R is that of q/t and the dimension of i dt is that of i·t. • Definite limits of integration must have the R b dimension of the differential; for example, in a f ðxÞ dx, both a and b must have the dimension of x. A similar condition applies to limits in general. • The units of infinite limits of integration ð1Þ are Runderstood to be those of the differential; e.g., t1 iðtÞ dt it is understood that 1 stands for in 1 an exceedingly large and negative time. A similar condition applies to limits in general. • With very few exceptions, arguments of functions must be dimensionless; for example, we cannot take the logarithm of 50 kg. The reason why is that ln (x) can be expressed as an infinite power series, and we cannot (e.g.) add kg to kg2 to kg3 . . . .7 • Finally, voltage, current, power, and time, if zero or infinite, are zero or infinite in any system of units. We do not attach units to those quantities when they are zero or infinite; for example, we say t!1, not t!1 s, because if time approaches infinity, it does so whether measured in seconds, minutes, or weeks.8 Similarly, we say v ¼ 0, not v ¼ 0 V, because if a voltage equals zero, it is zero in any system of units. It is poor practice to write statements such as “v ¼ v0et, where time t is expressed in milliseconds.” Such practice makes it impossible to check relations for dimensional consistency and thereby robs us of an opportunity to catch careless errors. Further, such practice robs us of many opportunities for developing insight; e.g., by hiding the all-important time constant in the exponential relation above. It is far better to adopt the convention that t always stands for time in seconds and to write the statement above as “v ¼ v0 et=t , where t ¼ 1 ms.”
7
Of course, the coefficients of a Taylor series can be dimensioned, and one could define different series for (e.g.) the logarithm of different physical quantities. Such an approach would be cumbersome, at best. 8 Some mathematical software (e.g., Mathcad) that allow units to be used insist that they be attached to all quantities, even those having zero magnitude. For example, if you ask Mathcad to compare 10 s to 0, you will get an error. You must compare 10 s to 0 s.
7
Units and dimensions are not only essential parts of the values of physical quantities, but also provide insight into the meaning and reasonableness of derived results. Sometimes they even guide derivations of new relations. They also provide a powerful means of checking correctness of equations and answers. An equation that is dimensionally inconsistent is incorrect. There is no reason to proceed with a solution until the error is found and corrected. Make it a habit to check all derived equations and relations for dimensional consistency. An equation is dimensionally consistent if all terms have the same unit. We use SI units exclusively, so you may check units instead of dimensions, which is somewhat easier, because it is easier to remember the units of quantities than it is to remember the (usually compound) dimensions for the quantities. We use SIðbÞ to denote the SI unit of a quantity b, where ( the SI unit of b; if b is dimensioned; SIðbÞ ¼ 1; if b is dimensionless; (1.1) and SIðabÞ ¼ SIðaÞ SIðbÞ;
a SIðaÞ ¼ : SI b SIðbÞ
(1.2)
Example 1.1. We wish to show that the dimension of the quantity RC (resistance times capacitance) is that of time. From Table 1.3, SIðRCÞ ¼ SIð RÞSIðCÞ ¼ VA1 A sV1 ¼ s: Thus the unit of the quantity RC is seconds (s) and the dimension of RC is time.
Example 1.2. We wish to show that the expression i¼C
dv dt
is dimensionally consistent, where i is current, C is capacitance, v is voltage, and t is time.
8
1 Introduction
Current i stands alone on the left, so we seek to reduce the unit of the term on the right to the ampere. From Table 1.3 V dv SIðvÞ 1 SI C ¼ SIðCÞ ¼ A: ¼ AsV dt SIðtÞ s Thus the equation is dimensionally consistent.
Exercise 1.4. Show that the relation 1 i¼ L
ðt 1
vðt0 Þdt0
where i is current, L is inductance, v is voltage, and t is time, is dimensionally consistent.
Exercise 1.5. Check each relation for dimensional consistency. ð di 1 t iðt0 Þdt0 ¼ 5v1 ; þ Ri dt RC 1 qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi R2 þ ðoLÞ2 V ðbÞ ¼ : I 1 þ oRC
ðaÞ L
As an aside, the SI system includes no unit for weight. Weight is force due to gravity and is approximately a fixed multiple of mass everywhere on the earth’s surface, given by f ¼ mg, where m is mass and g is acceleration due to gravity. Thus, on the earth’s surface, mass serves as well as weight to express how heavy one thing is relative to others; that is, if one thing has twice the mass of another, it also has twice the weight of the other (in the same location). Consequently, there is really no need for a quantity called weight. Mass serves just as well. Conversions from mass in kilograms to weight in pounds build in the acceleration due to gravity (approximately 9.8 m s–2) and are really conversions from mass to force on the
mass due to gravity. The conversion factor works out to be about 0.454 kg lb–1, so 1 kg (mass) of butter weighs about 2.2 lb.9 The size (scale) of a unit often is inappropriate to a particular problem or even to an entire discipline; for example, the meter is much too large a unit to use in atomic physics and much too small a unit to use in astrophysics. Even though the SI system is the official system of units, other units that have proved useful remain in use (e.g., the angstrom and the light-year). Also, engineers must communicate effectively with those in other professions and trades, not all of whom have embraced the SI system so warmly, and it often is necessary to convert one unit of measure to another (e.g., meters to inches). We use the SI system almost exclusively in this book so we omit a table of conversion factors. Such tables can be found in most standard handbooks.10 In the SI system, very large multiples and very small fractions of units are made more manageable by using named prefixes that denote multiplication by a power of ten. The power of ten denoted by most prefixes is a positive or negative whole multiple of three. Those that are not are not widely used in electrical engineering, except for the centimeter (0.01 m) and angstrom (1010m). Table 1.4 gives selected SI prefixes. Table 1.4 SI prefixes Prefix Femto Pico Nano Micro Milli Centi Kilo Mega Giga Tera Peta
9
Abbreviation f p n m m c k M G T P
Value 1015 1012 109 106 103 102 103 106 109 1012 1015
The abbreviation lb stands for libra, an ancient Roman unit of weight which was presumably the predecessor to the English pound. See Yunus A. Cengel and Michael Boles, Thermodynamics: An Engineering Approach (3rd Ed.), McGraw-Hill, 1998. 10 An especially complete table of conversion factors is given in the Handbook of Chemistry and Physics (76th Ed.), edited by David R. Lide, CRC Press, New York, 1995.
1.4 Symbols and Notation
There are three basic rules regarding use of prefixes: • Prefixes are not to be repeated or used with other prefixes; e.g., use pF, not mmF and ns, not mms. • Where a prefix is used with a symbol, the prefix and the symbol become one quantity that can be raised to a power or used in a fraction without parentheses; for example, 1 cm2 ¼ 104m2 and 4 m/ms ¼ 4000 m s1. • Prefixes are never used alone, even for purely numerical quantities. These rules are designed to eliminate ambiguity; for example, although the symbol m for meter and the prefix m for milli are identical, there is no possibility for confusion because m for milli is never used alone or repeated (mm always stands for millimeter, never milli-milli). Nonetheless, there remain possibilities for confusion. For example, does mV mean millivolt or meter-volt? In this case, we can avoid confusion by writing mV for millivolt and Vm for volt-meter. But what about Vms? Does it mean volt-millisecond or volt-meter-second? In such cases we can use spaces, hyphens, dots, or parentheses to avoid ambiguity. For example, Vms means volt-millisecond and Vm s, Vm-s, Vm s, and (Vm)s all mean volt-meter-second. There is no need (at present) to memorize any entries in the tables above. You will learn many of them through repeated use in subsequent sections. But you should learn the three rules above and become proficient at checking dimensions (units) using the procedure illustrated in the examples above. Again, you should form the habit of checking units with reasonable frequency as you work through a problem. Doing so will help you catch many careless errors and help you avoid the fruitless labor of solving incorrect equations. Exercise 1.6. Express each of the following without prefixes: (a) 100 mAs1 (b) 10 V ms1, (c) 100 kV A, (d) 10 mm ms2.
Exercise 1.7. Using prefixes, express each of the following in at least two other ways: (a) 5 mVs1, (b) 25 kAms, (c) 100 mJms1.
9
Exercise 1.8. Specify whether each m stands for meter or milli in each of the following: (a) Vms1, (b) m Ams1, (c) Nm·s1, (d) m2s1, (e) mms1.
1.4 Symbols and Notation Symbols for quantities and units used in this book are those in Table 1.3. Because the alphabet is finite, some symbols have more than one meaning. To the extent possible, we avoid conflicts as follows: • Symbols for quantities are always in italics and symbols for units are always in roman; e.g., C (italic) is the symbol for capacitance (a quantity) and C (roman) is the symbol for the coulomb (the SI unit of charge). This convention is not entirely satisfactory because it is difficult to distinguish italic and roman letters in handwritten notes and assignments. Where conflicts arise (and confusion is possible), we suggest using an underscore to denote roman (e.g., C for coulomb). • Symbols for complex representations of currents and voltages are printed under a tilde; for example, I˜ and V~ denote complex quantities called phasors, defined in Chapter 12, and used to represent sinusoidal currents and voltages. We use a tilde in these cases because V and I (no tilde) denote associated real quantities (the magnitudes of the corresponding complex quantities). • We rely on context when there is no tolerable alternative; for example, the symbols for period and temperature are identical, and we must rely on context to tell us what T stands for. • The principal quantities of interest in circuit analysis and design are time, current, voltage, work, and power. In this book, t always stands for time and i and v and their italic capitals always stand for current and voltage, respectively. • To avoid clutter, explicit time dependence often is omitted; for example, v and i alone denote v(t) and i(t), respectively and dv/dt stands for dv(t)/dt. The mathematical notation used in the text is generally that used in standard prerequisite mathematics
10 Table 1.5 Notation used in the text Symbol Meaning ! Approaches ffi Is approximately equal to Is identically equal to ) Implies or yields , Implies and is implied by iff if and only if e.g. For example i.e. Namely, or that is, or in other words
courses. Table 1.5 gives symbols and abbreviations used throughout the text. For example, we might write that 3x þ 4 ¼ 10 ) x ¼ 2, which reads as “three x plus four equals ten implies that (or yields) x equals two.” Equations are numbered only for cross-reference. A numbered equation is not necessarily an important equation. Boldface type is used when an important quantity or term is introduced or defined. Italic type is used to highlight secondary definitions, identify important terms, and emphasize important comments. As is standard in technical works, we use a number of Greek letters. Table 1.6 gives the Greek alphabet and the usual meaning (if any) assigned to each Greek letter in this book. For the most part, these choices reflect the meanings assigned to symbols in practice. Some (such as d) have multiple meanings, whereas others are not used. Also, the usual meaning is not necessarily the only meaning used in this book. We occasionally assign a meaning not given in Table 1.6 for temporary use in a particular development or section.
1 Introduction
particular numerical values for those quantities. Indeed, much of electrical engineering focuses on designing things (such as circuits) that create desirable relations among physical quantities, such as voltages. Resist the urge to prematurely replace quantities by their numerical values, even when those values are known and fixed. Instead, form the habit of working with symbols until the desired relation is obtained, checking units along the way. Only when you are certain you have a correct relation should you seek a particular numerical answer (with correct units), if that is what is called for in the problem. Jumping to numbers too quickly eliminates the possibility of checking dimensions, greatly limits the implications that can be drawn from the solution, and multiplies the number of different problems that must be solved by a large factor. To encourage you to use symbols and symbolic relations and to help you become proficient in that regard, many of the problems in this book ask you to obtain relationships among or (symbolic) expressions for quantities. Also, put your years of mathematics study to good use. Assign symbols to quantities that occur frequently in a development. For example, if you find the quantity oL/R occurs repeatedly in a particular development, you might define Q ¼ oL/R to simplify further manipulations. Where possible, use a symbol that suggests the dimension of the quantity; for example, if the quantity RC occurs repeatedly in a particular analysis, you might let t0 or t denote RC, because the dimension of RC is time.
1.6 Presentation of Calculations 1.5 Symbols Versus Numbers In general, symbolic relations among quantities are much more valuable than particular numerical values. For example, Newton’s law f ¼ ma is much more valuable and informative than would be a table of particular values for force, mass, and acceleration. The symbolic relation f ¼ ma tells us that acceleration is proportional to force, whereas knowing only that a 1 kg mass subjected to a 2 N force experiences an acceleration of 2 ms2 is of little general value. In engineering and especially in conceptual design, relations among quantities are of far more interest than
Intermediate steps in the calculation of a value from a symbolic expression can be presented in basically two ways: The first (and generally best for students) is to exhibit both the value and the unit of each quantity in the expression. The second is to simply exhibit values, attaching the correct unit to only the final expression. For example, suppose we must calculate the value of jZ j ¼
qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi R2 þ ð2pf LÞ2 ;
where R ¼ 1 kO, f ¼ 10 kHz, and L ¼ 10 mH. Any of the following presentations would be considered
1.7 Approximations
11
Table 1.6 Greek alphabet and common uses for characters Lower-case Name Usual meaning a Alpha Peaking factor b Beta Tolerance w Chi Not used d Delta skin depth; damping factor; loss angle
Upper-case A B X D
e f g i k l m n o p y r s t u o x c z
E F G H I K L M N O P Y P S T U O X C Z
Epsilon Phi Gamma Eta Iota Kappa Lambda Mu Nu Omicron Pi Theta Rho Sigma Tau Upsilon Omega Xi Psi Zeta
Error, permittivity, energy Angle Ripple factor Efficiency Not used Not used Wavelength Permeability; voltage gain Not used Not used 3.14159. . . Angle Resistivity Conductivity; damping ratio Time constant Not used Angular frequency Not used Angle Not used
acceptable by most publishers of technical journals and textbooks: jZj¼
qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2 ½1;000O2 þ 2p 104 Hz 102 H ¼1;181O;
jZ j ¼
qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ½1 kO2 þ ½2pð10 kHzÞð10 mHÞ2 ¼ 1:18 kO;
jZ j ¼
qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2ffi ½1; 000 2 þ 2p 104 102
¼ 1; 181 O ¼ 1:18 kO
:
In the first two of the three presentations above, the units of the quantities involved are shown throughout. In the third, the unit is attached to only the ultimate result, and the unit (O) transcends the equal sign. All three presentations are considered dimensionally correct. Which of these presentations you use will depend upon your instructor’s preference, your confidence in the dimensional correctness of the symbolic expression, and your familiarity with units and prefixes (e.g., you might recognize that the k in kHz and the m in mH in the second of the two presentations cancel). Generally, it is good to use the first form in the
Usual meaning Not used Not used Not used Increment prefix; e.g., Dx means a small increase in a quantity x Not used Angle, electric potential Not used Not used Not used Not used Not used Not used Not used Not used Product Angle Not used Sum Not used Not used Ohm (unit) Not used Angle Not used
beginning, progressing to the third as you gain familiarity with various expressions and the quantities involved.
1.7 Approximations Approximations are valuable and even inherent in engineering analysis and design. They are valuable because they can simplify computations and aid insight. In many cases, engineers employ without hesitation approximations that can introduce errors as large as 10%. Approximations are inherent because circuit parameters are imprecise. For example, the actual capacitance of a 10 nF capacitor might be anywhere in the range 10 nF 20%. As a reminder, we use the symbol ffi to denote is approximately equal to; e.g., p ffi 3:14. Opportunities for approximation arise repeatedly in circuit analysis and design. Almost all approximations are based in some way upon the basic approximation: jx1 j>>jx2 j ) x1 þ x2 ffi x1 :
(1.3)
12
1 Introduction
In many cases, the basic approximation (1.3) is acceptable if jx1 j 10j x2 j (error ffi 10%) because, as it turns out, values of circuit parameters often are even more uncertain than that. Example 1.3. Assume jR1 j jR2 j and find the approximate value of G¼
1 1 þ : R1 R2
Solution: G¼
1 1 R1 þ R2 R1 1 þ ¼ ffi ¼ : R1 R2 R1 R2 R2 R1 R 2
Or jR1 j jR2 j )
1 1 1 1 1
) þ ffi : R1 R2 R1 R2 R2
Example 1.4. Assume j xj 1 and find the approximate value of y ¼ sinðxÞ. Solution: Using Taylor’s expansion gives y ¼ sinðxÞ ¼ x
such an expression, and needing to make a quick mental or pencil-and-paper calculation, we might use p ¼ 3:0000 þ 0:1416 ffi 3 ðerror < 5%Þ; pffiffiffi 2 ¼ 1:000 þ 0:4142 ffi 1:5 ðerror ffi 6%Þ:
Certainly the wide availability of pocket calculators and personal computers has greatly reduced need for hand computation and therefore the need for approximations in numerical computations. On the other hand, ability to make approximations that simplify symbolic expressions is valuable, because such simplifications often facilitate insight; e.g., in identifying which components of a circuit are critical to performance. Judicious use of approximations can foster insights that even the most careful computer calculation cannot reveal.
Example 1.6. It is found that a performance measure called voltage gain for a certain electronic circuit is given by
x3 x5 þ ; 3! 5!
which can be written
x2 x4 y ¼ sinðxÞ ¼ x 1 þ : 3! 5! Because j xj 1,
x2 x4 1 þ ffi 1; 3! 5! and so y ¼ sinðxÞ ffi x; j xj 1:
Av ¼
b RC RL ; ðRB þ rb þ RS Þ ðRC þ RL Þ
where all quantities on the right are circuit parameters. It is known that RB rb , RB RS , and RL RC . Using reasonable approximations, simplify the expression on the right and identify the circuit parameters that are critical to obtaining a specified voltage gain. Solution: Using (1.3), we have RB rb ) RB þ rb þ RS ffi RB þ RS ; RB RS ) RB þ RS ffi RB ;
Examplep1.5. ffiffiffi Certain irrational numbers such as p and 2 arise often in expressions for quantities of interest in circuit analysis. Faced with
RL RC ) RL þ RC ffi RL : Thus
1.7 Approximations
13
b RC R L b RC RL ffi Av ¼ ðRB þ rb þ RS Þ ðRC þ RL Þ RB ðRC þ RL Þ ffi
b RC RL b RC ¼ : RB RL RB
Under the conditions given, the critical parameters are b, RC, and RB. The parameters RS, RL and rb have relatively little influence on voltage gain.
Exercise 1.9. The voltage gain of a certain circuit is given by Av ¼
a ; 1þab
An asymptotic approximation to a function is the limiting form of the function for either exceedingly large or exceedingly small values of the independent variable. As an example, functions of the form f ðxÞ ¼ 1 ex are encountered frequently in electrical engineering. Such functions arise in analysis of circuits containing capacitors and inductors, where (usually) x < 0 and in analysis of semiconductor devices, such as diodes and transistors where (often) x > 0. Thus two asymptotic approximations of this function are important: x < 0; jxj 1 ) 1 ex ffi 1; x 1 ) 1 e x ffi ex :
(1.6)
where a and b are circuit parameters. Assume ja b j 1 and give an approximate expression for Av. If this assumption holds, which circuit parameter determines the voltage gain of the circuit?
In some cases, these approximations are deemed valid if j xj 3, because e3 ffi 20 is 20 times larger than one (5% error) and e3 ffi 0:05 is only about 5% of one. In others, we might require j xj 5 or more, in which case the error in (1.6) is less than 1%.
Some care is required in applying (1.3) to quantities raised to powers. For example, even if j xj 1, it is not necessarily true that ð1 þ xÞn ffi 1, especially if jnj is large. In such cases, the binomial series expansion
Exercise 1.10. An asymptotic approximation used extensively in a subsequent chapter is
n ðn1Þ 2 n ðn1Þðn2Þ 3 x þ x þ 2! 3!
For what values of x is the error in this approximation less than 10%?
ð1þxÞn ¼ 1þnxþ
logðx þ 1Þ ffi logð xÞ; x 1:
often justifies the approximation ð1 þ xÞn ffi 1 þ n x:
(1.4)
The approximation (1.4) is justified if the quadratic term is much smaller (in magnitude) than the linear term; i.e., if jðn 1Þ xj 2:
(1.5)
For example, the true value of (1.05)4 is 1.21550625. Equation (1.4) gives ð1:05Þ4 ¼ ð1 þ 0:05Þ4 ffi 1 þ ð4Þð0:05Þ ¼ 1:2; which is within 1.3% of the true value.
Approximations for elementary functions can be obtained from Taylor series expansions. For example, x2 þ ffi 1 þ x; j xj 1 2! x2 x4 cosð xÞ ¼ 1 þ ffi 1; j xj 1 2! 4! x3 x5 sinð xÞ ¼ x þ ffi x; j xj 1 3! 5! ( ) 0; j xj 1 x2 x3 lnðx þ 1Þ ¼ x þ ffi 2 3 lnð xÞ; x 1 expð xÞ ¼ 1 þ x þ
(1.7)
14
1 Introduction
Exercise 1.11. Without using a calculator or computer, give approximate values for (a) 1 , (b) ln 1 þ e5 , (c) sinð0:501pÞ, (d) 2:02 1 1 2 þ e0:02 , (e) þ : 5 0:02
denote the zero-error value for I. The maximum error occurs if V has its maximum value and R has its smallest value. The minimum error occurs if V has its minimum value and R has its maximum value. Thus Vmax 1:02V0 ¼ ¼ 1:13I0 ; Rmin 0:90R0 Vmin 0:98V0 ¼ ¼ ¼ 0:89I0 : Rmax 1:10R0
Imax ¼ Exercise 1.12. A particular current in an electric circuit is found to be R2 i0 : i1 ¼ R1 þ R2 Find approximations for i1 (a) if R2 R1 and (b) as R1 becomes arbitrarily large (i.e., as R1 ! 1). You should cultivate your ability to make reasonable approximations, partly because approximations will help you determine whether a particular answer or expression is reasonable, but mainly because approximations often foster useful insight; e.g., as to which components of a circuit are critical to acceptable performance.
1.8 Precision and Tolerance Values of circuit components are never known with infinite precision. Rather, there is a precision associated with every such value; for example, the value of a resistance might be specified as 1 kO 5%, meaning that the actual value is somewhere between 950.0 and 1,050.0 O. Thus, there also are precisions associated with calculated values of functions of circuit parameters. Example 1.7. In the expression I¼V/R, the value of V is known to be in the range V0 2% and the value of R is known to be in the range R0 10%. What is the precision of the calculated value of I? Solution: Let V0, R0 denote the nominal (zeroerror) values for V and V, and let I0 ¼ V0/R0
Imin
It follows that 0:89I0 I 1:13I0 , or I ¼ I0 þ 13% or 11%, which might be written I ¼ I0 þ 13%/11%. In electrical engineering, limits on precision (e.g., the þ13% and 11% in Example 1.7) are called tolerances. For example, if the resistance of a resistor is known with precision 5%, we say that the tolerance of the resistor is 5%. Tolerances can be symmetric, as in 5%, but often are not. Capacitances often have asymmetric tolerances; e.g., C ¼ C0 þ 20%= 10%.
1.9 Engineering Notation In engineering notation (a special kind of scientific notation), values are typically written using the appropriate number of significant digits and a multiplier of ten raised to a power that is a whole multiple of three; for example, 1.56 106 and 67.0 103. Usually, the factor 10n is then replaced by a prefix on whatever unit is associated with the value written (see Table 1.4). For example, we would write 62.63 103 V(volts) as 62.63 kV (kilovolts). Using engineering notation can avoid ambiguity associated with trailing zeros on a whole number. For example, whereas the significance of the trailing zero in 320 is ambiguous, it is clear that 3.2 102 has two significant digits. Similarly, 3200 is ambiguous, but 3.20 103 has three significant digits. Exercise 1.13. Write each number using engineering notation. Assume trailing zeros are not significant. (a) 2015, (b) 16,380,000, (c) 0.759, (d) 0.000462, (e) 47.92 102.
1.10 Problems
Circuit components are available only in certain standard sizes and tolerances; for example, standard carbon-film resistors11 are readily available in tolerances of 10% and 5%, meaning that the actual resistance is within those percentages of the specified value. One can obtain high-precision components, such as metal-film resistors having tolerances of 0.1% or less; however, normal variations in ambient temperature and humidity or heating during soldering can cause the actual values to drift by 1% or 2% or more from the specified values. In general, actual values of circuit parameters are seldom within even 1% of specified values. Thus, when analyzing or designing circuits, it is almost always unnecessary and sometimes misleading to specify more than three significant figures in the numerical value of any quantity. Using too many significant figures can also cause you to miss opportunities for laborsaving approximations; for example, by leading you to believe that two resistors having resistances of 1:01256 kO and 1:01274 kO are different. It would be troublesome and distracting to give the precision of every computed value throughout our introduction to linear circuits, so unless otherwise stated in a problem or example, we shall for the most part treat values as if they are known exactly. Again, this is a relatively harmless practice in instructional material, so long as you are forewarned that numerical results are often specified more precisely than is truly justified. In actual practice, however, it is usually essential to specify the precision of circuit parameters, based upon the accuracy required of various currents and voltages.
1.10 Problems Section numbers in shaded boxes indicate prerequisite sections for problems that follow. Section 1.2 is prerequisite for the following problems. P 1.1 Pick one of the IEEE technical societies from the list on page 1.1 that sounds interesting to you. Visit the IEEE website (www.ieee.org) to find out more about the society. Briefly summarize the interests and 11
Resistance is defined in Chapter 2.
15
purpose of the society, and give an example of an item that is related to the society’s work. P 1.2 Use the procedure described in Section 1.2 to outline the content of this chapter; i.e., list (or give a reference to) the defined quantities (e.g., symbols, special notation), physical laws, derived results, and procedures (if any). Section 1.3 is prerequisite for the following problems. P 1.3 The symbols in each quantity below are as defined in Table 1.2. Determine the SI unit of the quantity. ð 1 t dq iðt0 Þdt0 , (b) VI cosðyÞ, (c) , (d) Ri2 , (a) C 1 dt v2 Rv L di , (g) (e) , (f) , (h) Cv. R R dt Z~ P 1.4 Check each equation for dimensional consistency. R1 R2 dv i þ R1 C ¼ 0, R1 þ R2 dt ð 1 t di (b) iðt0 Þdt0 þ L þ Ri ¼ v, C 1 dt ð dv v 1 t (c) C þ þ vðt0 Þdt0 ¼ i, dt R L 1 d 2 v R1 dv þ R2 i ¼ I, (d) R1 R2 C1 C2 2 þ L dt dt Z~1 Z~2 ~ V~ ~ (e) I þ ¼ V0 , R þ Z~1 Y~ 2 d v dv di (f) LC 2 þ RC þ v ¼ RC . dt dt dt (a)
P 1.5 Each quantity below is dimensionless. Express the SI unit of the variable a in terms of the SI units for current (A), voltage (V), and time (s). ðaÞ
aV RL
ðbÞ
IV dv ðcÞ a V 2 ðdÞ aLC dt
pffiffiffiffiffiffiffi a LC vðtÞ dt ðfÞ RC 0 2 32 dv C 6 apt dt 7 7 ðhÞ a2 6 ðgÞ 4 2 di 5 Cv L dt 1 ðeÞ a
ð t0
aRI di L dt
16
1 Introduction
P 1.6 Express the speed of light in furlongs per fortnight. (Refer to your dictionary for definitions of furlong and fortnight.) P 1.7 What is the SI equivalent of one light-year? P 1.8 Express 1 kV/MHz in V/Hz. P 1.9 Express the speed of light in m/ms. pffiffiffiffiffiffi P 1.10 Obtain the dimension and SI unit of LC, where L is inductance and C is capacitance. P 1.11 Obtain the dimension and SI unit of L/R, where L is inductance and R is resistance. P 1.12 Obtain the dimension and unit of I~Z, where I~ is current and Z is impedance. pffiffiffiffiffi P 1.13 Obtain the dimension and unit of me, where m is permeability and e is permittivity. P 1.14 Express the charge of an electron in m C, n C, and p C. P 1.15 Electrical utilities (and power-system engineers) often express energy in kWh (kilowatt-hours). Express 1 kWh in J (joules). P 1.16 Find the mass, in kilograms, of a man that weighs 200 lb. P 1.17 List as many units as you can for each of the following quantities and name disciplines in which such units would be used: (a) length, (b) area, (c) volume, (d) energy. P 1.18 The fine-structure constant is a ¼ 1 2 1 m 2 0 c qe h , where m0 is the permeability of a vacuum, c is the speed of light in a vacuum, qe is the charge of an electron, and h is Planck’s constant. Show that the finestructure constant is dimensionless. P 1.19 The Stefan-Boltzmann constant is s ¼ ðp2 =60Þ k4 h3 c2 , where k is the Boltzmann constant, h is Planck’s constant, and c is the speed of light in a vacuum. (a) Express the unit of the StefanBoltzmann constant in terms of basic SI units. (b) Show that the unit of the Stefan-Boltzmann constant can be expressed as W m2 K4. P 1.20 The SI unit for resistivity is the O m, but this unit is inconvenient (too large) in many cases, so resistivity is often expressed in mO cm. Find the factor that converts O m to mO cm. P 1.21 Show that 1 iðtÞ ¼ L
ðt 1
0
vðt Þdt
0
is dimensionally consistent. P 1.22 Show that 1Vm1 ¼ 1N C1 .
Section 1.7 is prerequisite for the following problems. P 1.23 For each function given below: (i) Find the small-x and large-x linear asymptotes. (ii) If the asymptotes intersect, calculate the values of the function and either asymptote at that point. (iii) Sketch a graph of the function, using the asymptotes as guides. 1 (a) f ðxÞ ¼ tan1 ð xÞ, (b) f ðxÞ ¼ , 1 þ x2 ( 0; x < 0; 1 (c) f ðxÞ ¼ , (d) f ðxÞ ¼ x ex ; x 0; ( 0; x < 0; (e) f ðxÞ ¼ x 1 e ; x 0: P 1.24 A certain voltage Vout is expressed in terms of another voltage Vn by Vout ¼
Rout mR1 Vn ; Rout þ R1
where R1, Rout are resistances and m is dimensionless. It is known that R1 Rout and m 1. Find a reasonable approximation for Vout. P 1.25 A certain voltage VL in an electric circuit is found to be VL ¼
RL VT ; RT þ RL
(a) Find a reasonable approximation for VL if RL RT . (b) Find a reasonable approximation for VL if RT RL . (c) Find VL as RT becomes arbitrarily large (i.e., as RT ! 1). P 1.26 A performance measure called current gain for a particular circuit is found to be Ai ¼
Rin Rout RS g ; ðRout þ RL ÞðRin þ RS Þ
where all quantities on the right are circuit parameters. (a) Find a reasonable approximation for Ai if Rout RL . (b) Find a reasonable approximation for Ai if Rin RS . (c) Find a reasonable approximation for Ai if both Rout RL and Rin RS .
1.10 Problems
17
(d) The current gain Ai is dimensionless. What is the SI unit of g? P 1.27 Give asymptotic approximations to qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi and for (a) 0 < f f0 log 1 þ ð f =f0 Þ2 (b) f f0 > 0. P 1.28 Given that R1 R2 R3 , obtain an 1 R1 þ R3 approximation to þ . R1 R3 R2 P 1.29 Given that R1 R2 R3 , obtain an R1 R2 R3 . approximation to R1 R2 þ R1 R3 þ R2 R3 P 1.30 Let h i h i Gð f Þ ¼ log 1 þ ð f =f0 Þ2 þ log 1 þ ð f =f1 Þ2 h i ; log 1 þ ð f =f2 Þ2 where 0 f0 f1 f2 . Give asymptotic approximations for G(f) for (a) f0 f f1 , (b) f1 f f2 , and (c) f f2 P 1.31 Let qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi K 1 þ ðf =f1 Þ2 H ð f Þ ¼ qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiqffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ; f0 f1 f : 1 þ ðf =f0 Þ2 1 þ ðf =f2 Þ2 Give asymptotic approximations for H(f) for (a) f0 f f1 , (b) f1 f f2 , and (c) f f2 P 1.32 Show that if x and y are both positive, then 1 1 1 þ > : x y xþy
R1 , where the precision of each R is 5% R2 R1 R2 , where the precision of each R is 5% (b) R1 þ R2
(a)
(c) ð f =f0 Þ2 , where the precision of f0 is 1%. Does the magnitude of the error depend upon the variable f ? (d) 20 log½1 þ ð f =f0 Þ2 , where f is known exactly, f f0 , and the precision of f0 is 5%. Does the magnitude of the error depend upon the variable f ? (e) expðt=RCÞ for t ¼ 20 ms, where R ¼ 1 kO 5% and C ¼ 20 nF 20%. (f)
R1 R2 R3 , where the precision of R1 R2 þ R1 R3 þ R2 R3 each R is 1%
Section 1.9 is prerequisite for the following problems. P 1.34 Express each of the following using engineering notation. Omit ambiguous zeros. (a) 14,600 V, (b) 9,870,000 W, (c) 48:3 108 , (d) Five million people, (e) 0.0056, (f) 0.0001, (g) 0.000708. P 1.35 Express each of the following using unit prefixes; for example, as in 47; 000 O ¼ 47k O. (a) 12 million volts, (b) 4:2 106 A, (c) 56 105 W, (d) 0.050 V, (e) 0.0002 A, (f) 4:8 63:4 109:0m, (g) 0:0506 g 2048, (h) 10 109 Hz, (i) 34:7 1013 O.
Section 1.8 is prerequisite for the following problems.
P 1.36 Express each of the following using engineering notation, without using unit prefixes; for example, 123 kW ¼ 123 103 W.
P 1.33 Estimate the precision of the indicated quantity:
(a) 55GHz, (b) 12 ns, (c) 100 MW, (d) 2:2 kOs, (e) 100nF, (f) 14:6 ms, (g) 12mm, (h) 47 mF, (i) 12pF (j) 108 mO cm, (k) 75 kV A, (l) 100 T O, (m) 1 fA.
.
Chapter 2
Current, Voltage, and Resistance
of another point charge q2 is given (in a vacuum) by Coulomb’s law
In this chapter, we define current and voltage, which are among the principal quantities of interest in circuit analysis. We present Ohm’s law, which is one of the fundamental laws of electrical engineering, and which is the defining relation for resistance and conductance.
f ðxÞ ¼
• There are two kinds of charge: The negative charge of an electron and the positive charge of a proton. The charge of an electron is qe ffi 1:602 1019 C: The charge of a proton is qp ¼ qe : • Like charges (charges having the same sign) repel each other and unlike charges attract each other. The force on a point charge2 q1 due to the presence
(2.1)
where x is the distance between the charges and k ¼ ð4 p er e0 Þ1 is a constant whose value depends upon the medium. In free space, k is approximately 9 109 N m2 C2 : The force on q1 given by (2.1) is attractive (directed toward q2) if q1 and q2 have opposite signs and repulsive (directed away from q2) if q1 and q2 have the same sign. The fact that charges exert forces on one another allows us to establish conditions under which some charges make other charges do useful things.
2.1 Charge and Current Charge is a property of electrons and protons, which are building blocks of atoms. The SI unit of electric charge is the coulomb (C).1 A quantity of charge is represented by the symbol q and is in general a function of time. Physicists are still hard at work trying to determine what charge is made of, but we do not need to await the results. We already know enough about how charge behaves to make it do many useful things. We accept charge as an undefined quantity whose properties are well understood. For electrical engineers, the important properties of charge are the following:
q1 q2 q1 q2 ¼k 2 ; 2 4 p er e0 x x
• The charge of an electron (or proton) is the smallest unit of charge and all charges are whole multiples of that fundamental unit. This fact is unimportant in ordinary circuit analysis, where so many electrons and/or ions are involved in the processes of interest that we can treat quantity of charge as a real variable–one that can assume any value. But it might be important in future ultrasmall devices, where relatively few electrons will be involved in processes of interest. • Charge can be neither created nor destroyed; that is, total charge is conserved.3 If we enclose a volume
1
After the French physicist Charles Augustin de Coulomb (1736–1806). 2 In practical applications, two charges can be considered point charges if their radii are much smaller than their separation.
3
Total charge is the algebraic sum of charge. Thus, the net charge of a hydrogen atom, which consists of one electron and one proton, is zero.
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_2, # Springer ScienceþBusiness Media B.V. 2011
19
20
2 Current, Voltage, and Resistance
with a surface and monitor the charge passing through the surface, any increase or decrease in the net charge enclosed in the volume will be accounted for by passage of charge through the surface. It is good that charge is conserved, because if charge could suddenly appear (or disappear) here and there, it would be difficult to keep track of and control. • A moving charge creates a magnetic field and a magnetic field exerts a force on a moving charge. These facts make electric generators, motors, and a host of other devices possible. Because of the properties above, charge can be made to do useful work. We can use electric charge to move enormous amounts of energy easily from one place to another, transmit information from one place to another, perform computations at unimaginable speed, convert mechanical energy to electrical form (and vice versa), and do many other useful things. To do work, charge must move under the influence of a force. Consequently, moving charge usually is of more interest to electrical engineers than charge itself. Motion or flow of charge is called current, denoted by i. By convention, the positive direction of current is opposite to the direction of electron flow.4 Current i through a plane (e.g., a cross section of a wire) is defined by5 i¼
dq ; dt
electron flow
positive current
Fig. 2.1 The direction of positive current is opposite to the direction of electron flow. See Example 2.1
then (2.2) gives the current passing into the space through the enclosing surface. The SI unit of current is the ampere (A),6 where 1 A equals 1 C s1. Example 2.1. A steady flow of 1020 electrons per second is directed from left to right through a cross section of a wire, as illustrated in Fig. 2.1. The current from left to right through the cross section is constant and equals electrons coulombs 1:602 1019 i ¼ 1020 second electron : 1 ¼ 16:02 Cs ¼ 16:02A
The current from left to right is negative because negative charge is moving from left to right. The current from right to left is positive and equals +16.02 A.
(2.2)
where dq is a quantity of charge passing through the plane in time dt and i is the current through the plane in the direction of the flow of positive charge. Alternatively, if q is a quantity of charge in an enclosed space,
Exercise 2.1. An electric current is established in a tank of salt water, as shown in Fig. 2.2. The positively charged sodium ions are drawn left to the negative electrode and the negatively charged chlorine ions are drawn right to the positive electrode. Each ion is singly charged and N ions reach each electrode during each interval T. Give an expression for the current I. Show that the expression is dimensionally consistent.
4
We have Ben Franklin to thank for this unfortunate accident of history. He decided to call the static charge induced on glass by rubbing the glass with silk positive and stated that the direction of current is from positive to negative (from glass to silk). Had he made either of these choices the other way, the positive direction of current would be in the direction of electron flow. 5 Explicit time-dependence often is omitted for the sake of brevity. Thus, in (2.2) q stands for q(t) and i for i(t). Also, current defined by (2.2) is called conduction current. When you study electromagnetism, you will learn about another kind of current called displacement current, that does not involve flow of charge. Conduction current is the current of interest in ordinary circuit analysis, where we are relatively unconcerned with the inner workings of circuit elements.
6
After the French Mathematician and Physicist Andre´ Marie Ampe´re (1775–1836), who discovered basic laws of electromagnetism.
2.2 Electric Field
21
I
Battery
Fig. 2.2 See Exercise 2.1
2.2 Electric Field In this section, we review the definition of work and define the electric field established by a charge, drawing on an analogy with gravity and the gravitational field. This section is preparation for the next, where voltage is defined in terms of work done on a charge by an electric field. Recall from physics that potential energy is capacity for doing work and that the work w done by a force f(x) on an object as the object moves from x1 to x2 is given by7 w¼
ð x2
f ðxÞ dx:
(2.3)
x1
The work done by the force is positive if the force is in the direction of motion and negative if the force is opposite to the direction of motion. Another way to say this is that the force does work on the object if the force and motion are in the same direction and work is done on whatever provides the force if the force and motion are in opposite directions. The SI unit of work is the joule (J),8 where (in mechanical units) 1 J equals 1 N-m. Work and energy are expressed in the same unit (J) and are physically the same thing. The distinction between work and energy is semantic, but useful. 7 To avoid using vector notation, we assume the force f(x) is directed along the x-axis, in either the same direction as the motion or opposite to the direction of motion. 8 After the English physicist James Prescott Joule (1818–1889).
Energy describes the state of something; for example, we might speak of the potential energy of a mass that has been raised to some height or the kinetic energy of a moving mass. Work is a quantity of energy transferred from one thing to another or converted from one form to another; for example, w in (2.3) is work because it is a quantity of energy transferred from whatever supplies the force f to an object acted on by the force. Similarly, a quantity of electrical energy converted to mechanical form by an electric motor is called work. An electric field and its interaction with charge are analogous to a gravitational field and its interaction with mass. On or near the earth’s surface, the gravitational force f on a mass m is nearly independent of position, is directed toward the center of the earth, and is given by f ¼ mg, where g is the acceleration due to gravity (approximately 9.8 m s–2 at sea level). For purposes of ordinary (non-relativistic) mechanics, we can define gravitational field strength F (a vector) near the earth’s surface as the force per unit mass due to gravity; that is, as the gravitational force on a mass divided by the mass. Thus, the magnitude of the field strength F is F ¼ f =m ¼ ðmgÞ=m ¼ g and its direction is toward the center of the earth. A gravitational field possesses potential energy because it does work on a mass that is allowed to fall. The work done on the mass by the gravitational field as the mass falls from height h to the ground is w ¼ force x distance ¼ mgh. To put this another way, the work w ¼ mgh is the amount of energy transferred from the field to the mass as the mass falls from height h. The work the gravitational field can do on the mass (the energy that can be transferred from the field to the mass) increases with the height of the mass. Thus, energy is stored in the gravitational field when a mass is raised and energy is released by the field (transferred to the mass) when the mass falls.9 The gravitational potential at a distance h above (but near) the earth’s surface is defined by ’ðhÞ ¼ g h and equals the work done per unit mass as a mass falls from or is 9
In this discussion, we are concerned only with energy exchanged between the gravitational field and a single mass. There may be other forces acting on the mass in addition to that due to gravity, but they do not affect the energy exchange between the mass and the field; for example, we can throw a mass toward the ground, in which case additional energy is transferred to the mass, but the energy transferred to the mass from the field is unaffected by the throwing.
22
2 Current, Voltage, and Resistance
raised to a height h. Thus the work w done is given by w ¼ m ’ðhÞ: If the mass falls, work is done by the field (energy is transferred from the field to the mass). If the mass is raised, work is done on the field (energy is transferred from the mass to the field). Example 2.2. An object having mass m ¼ 2 kg is raised from the ground to a height h ¼ 10 m and released. The potential energy stored in the field when the object is raised is w ¼ m gh ffi ð2 kgÞ 9:8 m s2 ð10 mÞ ¼ 196 J: When the object is released, this energy is given back to the object as kinetic energy. The kinetic energy of the object when it hits the ground is 196 J. When the object is raised, 196 J are stored in the field. When the object is released, the field gives up the stored energy by doing work w ¼ 196 J on the object.
Exercise 2.2. An object having mass m is tossed up. When it strikes the ground, its velocity (downward) is u. Give an expression for the height attained by the object. Show that the expression is dimensionally consistent. Below, by analogy with gravitation, we define electric field strength and electric potential. We illustrate these definitions using the field and potential due to a point charge. The stated definitions are general, but the expressions given apply to a point charge only. Consider the situation shown in Fig. 2.3, where positive point charges q1 and q2 are separated by a distance x. We assume the charge q2 is fixed and we can somehow move the charge q1 about. By Coulomb’s law (2.1), the force f(x) on q1 due to the presence of q2 is given by
q2
q1 x
Fig. 2.3 Coulomb force
f ð xÞ ¼ k
q1 q2 ; x2
where k ¼ 9 109 Nm2 C2 : Because like charges repel, the force given by (2.1) is repulsive; that is, the force is positive if the charges have the same sign. A positive (repulsive) force on q1 is directed away from q2 along a line from q2 through q1, as shown in Fig. 2.3. The force given by (2.1) is attributed to an electric field produced by the charge q2. The electric field strength E (vector) at a point is defined as the force per unit charge on a positive charge at that point. Thus, the electric field strength at a distance x from an isolated point charge q2 is given by Eð x Þ ¼ k
q2 : x2
(2.4)
The coulomb force given by (2.1) and the electric field strength given by (2.4) for a point charge depend only upon distance from the charge; that is, electric field strength is directed radially outward from a positive charge, as illustrated in Fig. 2.4. If q2 were negative, the electric field strength given by (2.4) would be negative, meaning the force on a positive charge is directed radially inward toward q2. Note that (2.4) gives electric field strength a distance x from a point charge. It is not a general result. Other charge distributions lead to different expressions for electric field strength. If the charge q1 in Fig. 2.3 is free to move, and if both charges have the same sign, then the charge q1 will accelerate away from q2, taking energy from the electric field as it accelerates. On the other hand, if we somehow force the charge q1 toward the charge q2, we
E
E
f
Fig. 2.4 Electric field due to a point charge. Electric field lines of force emanate from positive charge and terminate on negative charge
2.3 Electric Potential and Voltage
23
store potential energy in the field because we increase the capacity of the field to do work on the charge q1. If a positive charge moves in the direction of electric field strength, then the motion and the force are in the same direction and energy is transferred from the field to the charge. If a positive charge moves opposite to the field, energy is transferred to the field from whatever moves the charge. Recall that a mass moving toward the earth’s surface (in the direction of the gravitational field) takes energy from the gravitational field and a mass moving away from the earth’s surface (opposite to the direction of the gravitational field) gives energy to the gravitational field. Similarly, a positive charge moving in the direction of an electric field takes energy from the field and a positive charge moving opposite to the direction of the field gives energy to the field. Currents in electric circuits are due primarily to electron flow, but we may treat a flow of electrons in one direction as a flow of positively charged particles in the opposite direction. Thus energy is taken from an electric field by a current moving in the direction of the field and energy is given to the field by current moving opposite to the direction of the field. Continuing the point-charge example, we can calculate the work done on the charge q1 by the field using (2.3), where the force f(x) is the product of the charge q1 and the electric field strength (the force per unit charge). From (2.4), the force on the charge is given by f ðxÞ ¼ EðxÞ q1 ¼ k
ðb
f ðxÞ dx ¼ k q1 q2
a
¼ k q1 q 2
ðb
dx 2 a x
1 b 1 1 ¼ k q1 q2 : x a b a
Example 2.3. In Fig. 2.3, the movable charge q1 ¼ 1 mC and the fixed charge q2 ¼ 5 mC. If q1 moves from a ¼ 10 m to b ¼ 20 m (away from q2), the work done by the field on q1 is given by (2.5) and equals w ¼ k q1 q2
1 1 b a
1 1 ¼ 2; 250 J ffi 45 103 N m2 20m 10m
which is approximately the work done in lifting a 225 kg mass to a height of 1 m (a 225 kg mass weighs about 496 lb).
Exercise 2.3. Point charges q, –q are a distance d apart. Obtain an expression for the charge q in terms of the separation d and the force f each charge exerts on the other. Show that the expression is dimensionally consistent.
2.3 Electric Potential and Voltage
q1 q2 : x2
Suppose both charges have the same sign, q2 is stationary, and the charge q1 moves from point a to point b on a line drawn from point a to q2. From (2.3), the work done on the charge by the field is given by w¼
field), w is negative, and work has been done on the field. In the first case, energy is removed from the field (transferred to the charge). In the second, energy is stored in the field.
(2.5)
If a < b; the charge q1 moved away from q2 (in the direction of the field), the work w is positive, and the field has done work on the charge. If a > b; the charge q1 moved toward q2 (opposite to the direction of the
We continue with the point-charge example. From the discussion above, the potential energy of the field due to q2 depends upon the position of q1 relative to that of q2. The closer is q1 to q2, the greater is the potential energy of the field and the farther is q1 from q2, the smaller is the potential energy of the field. The electric potential at a point is denoted by F and is defined as the work done on an electric field (or by an external force) per unit charge when a positive charge is brought from infinity (where the electric field strength is assumed to be zero) to the point.10 Thus the electric potential at a point is numerically (but not
10
Note that electric potential is not the same as potential energy. The unit of electric potential is that of energy divided by charge.
24
2 Current, Voltage, and Resistance
dimensionally) equal to the work required of an external force to bring a one-coulomb positive charge from infinity to the point. The work done and thus the potential can be positive or negative, depending upon whether the charge is forced to move against the electric field or is allowed to drift in the direction of the field. The SI unit of electric potential is the volt (V),11 where 1 V equals 1 J C–1. Equation (2.5) gives the work done by the field on a point charge when the charge is moved from a to b in the neighborhood of another point charge. The work done on the field is just the negative of the work done by the field. Changing the sign of the right side of (2.5), dividing by q1, and taking the limit as a ! 1, we find that the electric potential (the work done on the field per unit charge) in bringing a charge from x ! 1 to x ¼ b is given by FðbÞ ¼
k q2 : b
(2.6)
Point b can be any point (any distance from q2), so the electric potential at distance x from a point charge q2 is given by FðxÞ ¼
k q2 : x
(2.7)
For a point charge, the electric field strength given by (2.4) and the electric potential given by (2.7) are related as EðxÞ ¼
FðxÞ : x
(2.8)
Electric field strength is defined as force per unit charge, so electric field strength can be expressed in units of newtons per coulomb (N C–1). Equation (2.8) for electric field strength is specific to a point charge, but illustrates the fact that electric field strength also can be expressed in volts per meter (V m–1), which is the preferred unit in electrical engineering (both are SI units).
11
After Count Alessandro Volta (1745–1827), an Italian inventor who discovered hydrolysis and invented the battery and the electric condenser (now called a capacitor).
Example 2.4. From (2.4) the electric field strength at a point 10 m from a 5 mC point charge is 9 109 N m2 C2 5 106 C kq E¼ 2 ffi x ð10 mÞ2 ¼ 450N C1 ¼ 450Vm1 : From (2.7), the electric potential at the point is F¼
9 109 N m2 C2 5 106 C kq ffi ð10 mÞ x
¼ 4:50 kV:
Exercise 2.4. Equal point charges are fixed in space as shown in Fig. 2.5 and exert a force f on one another. Find an expression for the electric potential due to the charges at the point x1 > x0 > 0 in terms of the distances x0 ; x1 : and the force f Show that the expression is dimensionally consistent. Hint: The total electric potential due to two point charges is the sum of the potentials due to each charge individually. What causes water to flow through a pipe is a pressure difference from one end of the pipe to the other. It is pressure difference that causes flow, not absolute pressure at either end. Similarly, what causes charge to flow is a potential difference. In electric circuits, we are interested in potential differences, not absolute potentials. The voltage at point a with respect to point b, denoted by vab ; is the potential difference vab ¼ FðaÞ FðbÞ;
(2.9) q
q
q
0
x0
Fig. 2.5 See Exercise 2.4
x x1
2.4 Ohm’s Law and Resistance
25
where FðaÞ is the potential at point a and FðbÞ is the potential at point b The SI unit for electric potential is the volt, so the SI unit of voltage is also the volt (V). Note that the voltage vab is the work done on the field per unit charge in moving a charge from point b to point a. The difference of two potentials can be formed in two ways and the order of the subscripts a and b is significant. Two points are required to specify (or calculate, or measure) a voltage and one of the points must be identified as the reference. By convention, the second subscript on the voltage defined by (2.9) identifies the reference point; e.g., in (2.9) the potential FðbÞ is the reference potential. To measure vab with a voltmeter, we would touch the black (–) probe to the reference point b and the red (+) probe to point a. If we made the measurement the other way around, we would be measuring the negative of vab because, by comparison with (2.9), vba ¼ FðbÞ FðaÞ ¼ vab :
(2.10)
Example 2.5. From (2.9) and (2.7), the voltage at a point a with respect to another point b in the neighborhood of an isolated point charge q2, is given by k q2 k q2 1 1 ; ¼ k q2 vab ¼ xa xb xa xb where xa is the distance from point a to q2 and xb is the distance from point b to q2. If q2 is positive, the voltage vab is positive if a is nearer q2 than b (if xa < xb ) and negative if a is farther from q2 than b (if xa > xb ).
Exercise 2.5. The point a is at a distance xa from an isolated point charge q, as shown in Fig. 2.6. Let vab denote the voltage between a and another point b. Express the distance d in terms of q, xa, and vab. Show that the expression is dimensionally consistent. If a voltage vab is positive, the potential energy of a positive charge is greater at the point a than it is at point b. In that case, a positive charge experiences a
a
q xa
b d
Fig. 2.6 See Exercise 2.5 Φ(a) > Φ(b) vab > 0
voltage drop
a
b voltage rise
Fig. 2.7 Definitions of voltage rise and voltage drop +
v
–
i
Fig. 2.8 Voltage polarity and current direction in Ohm’s law
voltage drop in moving from a to b and a voltage rise in moving from b to a.12 If vab is negative, the reverse is true. Thus current from a to b goes through a voltage drop if vab is positive and a voltage rise if vab is negative. Figure 2.7 illustrates these definitions.
2.4 Ohm’s Law and Resistance Ohm’s law states that the voltage across a piece of material is proportional to the current through the material; for example, if the object in Fig. 2.8 represents a sample of conducting material, the voltage v across the sample is related to the current i through the sample according to13 v ¼ R i;
(2.11)
where R is called the resistance of the sample. The SI unit of resistance is the ohm (O),14 where 1 O equals 1 V/A (1 VA1). Despite its simplicity, Ohm’s law is one of the most important laws in all of electrical engineering.
12
The terms rise and drop arise from analogy with gravity, where a mass gains potential energy if we raise it and loses potential energy if we lower (or drop) it. 13 In general (and usually), both voltage and current vary with time. 14 After the German physicist Georg Simon Ohm (1787–1854).
26
2 Current, Voltage, and Resistance
In Ohm’s law (2.11) the positive direction of current is in the direction of a voltage drop (from a higher to a lower potential), as shown in the figure. If either the assumed voltage polarity or the assumed current direction is opposite to that shown in Fig. 2.8, the right side of (2.11) must be negated.
Example 2.7. The resistivity of pure copper at 20 C is 1:72 108 O m: At 20 C, the resistance of a pure copper cylindrical wire having diameter d ¼ 0:2 cm and length l ¼ 5km is
Example 2.6. In Fig. 2.8, the current i is equal to 5 A in the direction shown and the resistance of the sample is 100 O. From (2.11), the voltage v is 500 V.
If the current in the wire is 15 A, the voltage drop from end to end is
1:72 108 Om ð5000 mÞ rl R¼ ffi ffi 27:4 O: A ðpÞ ð0:001mÞ2
v ¼ R i ffi ð27:4 OÞð15AÞ ffi 411V:
Exercise 2.6. Refer to Fig. 2.9. Find the current i2 if the voltage v is 10 V and the resistance of the sample is 1 kO.
Exercise 2.7. A certain conductor on a printed circuit board has a rectangular cross section. The conductor has width w0 and is built from a material having resistivity r0 : Suppose we want to build the conductor from a different material having resistivity r1 : Find an expression for the new width w1 if we want to maintain the length, height, and resistance of the original conductor
2.5 Resistivity The resistance of a sample of material depends upon the kind and state of the material (e.g., copper at 20 C) and upon the size and shape of the sample. The effects of the kind and state of the material can be separated from those of size and shape. A material can be characterized by its resistivity, denoted by r, which is independent of size and shape. The resistance of a homogeneous sample of material having resistivity r, length l, and uniform cross-sectional area A is given by R¼
rl : A
(2.12)
The SI unit of resistivity is the ohm meter (O m).15 Depending upon the material, resistivity can depend strongly or weakly upon the state of the material (e.g., temperature and pressure). +
v R
–
Many materials are classified according to their resistivity as insulators (very high resistivity) or conductors (very low resistivity). Materials having resistivities between these extremes are called semiconductors. Glass and air are good insulators. Most metals are good conductors.16 Silicon containing certain impurities is a semiconductor.
2.6 Conductance and Conductivity The reciprocal of resistance is called conductance and is denoted by G:
i2
G¼
1 : R
(2.13)
Fig. 2.9 See Exercise 2.6 16
In reference works, resistivity often is specified in mO cm (10–8 O m).
15
Metals are good conductors because the outer electrons of metal atoms are only loosely held and are relatively free to “drift” through the solid under the influence of an applied voltage.
2.7 Resistors
27
The unit of conductance is the siemen (S), where 1 S ¼ 1 O1. The reciprocal of resistivity is called conductivity, denoted by s: 1 s¼ : r
(2.14)
The unit of conductivity is siemens per meter (S m1). From (2.12)–(2.14), the conductance of a homogeneous piece of material having conductivity s, length l and uniform cross-sectional area A is given by G¼
sA : l
(2.15)
Using conductance, Ohm’s law is written i ¼ G v:
(2.16)
Conductance often is used symbolically in place of resistance when writing circuit equations that would otherwise contain many terms of the form v=R; however, in specifications of values, resistance is almost always the quantity specified.
Resistors are fixed (have fixed values) or variable. Variable resistors can be continuously variable, like potentiometers and rheostats, or have contacts at only certain angular or linear positions. A continuously variable resistor incorporates a tap or a slide that can be positioned and repositioned along a strip of conducting material or wirewound core. Those having only a limited set of possible values sometimes are called encoders because they provide a precise relation between position and resistance. Figures 2.10 and 2.11 show assorted fixed and variable resistors. Years ago, carbon-composition resistors were the most common (numerous) kinds of resistors. Nowadays, the most numerous resistors are film resistors, and carbon-composition resistors have almost disappeared. Chip resistors, most small axial-lead resistors, and resistors in integrated circuits are constructed of thin carbon or metallic films (often, nichrome or tantalum nitride). In chip and integrated resistors, the film is deposited on an insulating substrate and joined to contact pads or conductors at each end, as illustrated in Fig. 2.12. The resistance of a thin-film resistor is given by the usual relation R¼
2.7 Resistors Resistance is introduced (intentionally) in circuits using components called resistors. Resistors are made of various materials and in various configurations. A composition resistor is essentially a cylindrical core of material consisting of very fine carbon or metallic granules imbedded in a non-conducting or semi-conducting material and incased in plastic. The resistance is determined by the concentration of carbon or metal in the core material. There are two main types of film resistors. One kind is made by depositing a film of metal or carbon on a non-conducting cylindrical core and then cutting away some of the material to leave a spiral ribbon of the material. The other kind consists of a thin film of (usually) metal or certain metal oxides on a planar surface. Many chip resistors and surface-mount resistors are of this kind, as are resistors in integrated circuits. A wirewound resistor is just what the name suggests: A wire wound on a non-conducting core. The resistance of a wirewound resistor is determined by the resistivity, cross-sectional area, and length of the wire. If adjacent windings are in contact, the wire is insulated.
rl rl ¼ : A wh
(2.17)
where w and h are the width and thickness, respectively, of the strip, r is the resistivity of the film, and l is the length of the strip. It is conventional and convenient to define the sheet resistance of a film resistor as r ¼ sheet resistance: h
(2.18)
Sheet resistance has the dimension of resistance and usually is expressed in either ohms or ohms per square. With this definition (2.17) becomes R¼
r l ¼ ðsheet resistanceÞ ðnumber of squaresÞ: h w (2.19)
The number of squares in a film resistor is dimensionless and is obtained by dividing the length of the film into squares having sides equal to the width of the film, as illustrated by Fig. 2.13.
28
2 Current, Voltage, and Resistance
Fig. 2.10 Fixed resistors (not to scale): (a) Aluminumencased wirewound, (b) power wirewound, (c) metaloxide, (d) carbon-film, (e) metal-film, (f) carbon composition, (g) surfacemount chip (Photographs courtesy Rapid Electronics, Ltd.)
Fig. 2.11 Variable Resistors (not to scale) (Photos courtesy Rapid Electronics, Ltd.)
The resistance of a thin-film resistor is determined by the sheet resistance, which is a function of the material and film thickness, and the number of squares. The resistance is independent of the size of a square. For example, a film 2 mm wide by 10 mm long has the same resistance as one 200 nm wide and 1mm long, as illustrated by Fig. 2.14, if both have the same sheet resistance.
Tantalum nitride (TaN) is widely used for thin-film resistors, partly because the resistivity of TaN can be varied over a wide range by varying the composition. A common composition has a resistivity of about 250 mO cm at 25 C: A common thickness for thin-film resistors is 50 nm. A 50 nm film of 250 mO cm TaN has a sheet resistance of 50 O=sq; which proves to be a convenient value.
2.8 E Series, Tolerance, and Standard Resistance Values
be trimmed to a very precise value by monitoring the resistance while using a laser to cut one or more notches in the film, as illustrated by Fig. 2.15. It is difficult to specify the width and depth of the notch because of variations in the thickness and even the composition of the film (which is why the natural tolerances are relatively poor). Ability to trim thin film resistors to such precise values is important to design and construction of high-precision electronic circuits.
contact pads
l nichrome film
w top view
h
edge view
2.8 E Series, Tolerance, and Standard Resistance Values
Fig. 2.12 Thin-film resistor
1 sq
1 sq
29
1 sq
1 sq 2
Fig. 2.13 Thin-film resistor squares
Exercise 2.8. The resistivity of a certain composition of nichrome is108 mO cm at 25 C: What is the thickness of a layer of this material that will have a sheet resistance of 75 O=sq at 25 C?
Exercise 2.9. The length of the film in a 500 O thin film resistor is fixed while its width is halved. What is the new resistance?
Exercise 2.10. The resistivity of a certain material at 25 C is 95 mO cm: (a) What is the sheet resistance of a 100 nm thick film of the material? (b) What is the resistance at 25 C of a thin film resistor made of 100 nm film that is 75 nm wide and 1mm long? The natural tolerances of thin film resistors are at best about 10%; however, a thin film resistor can
It is impossible for parts suppliers to stock resistors in every possible value, so a convention for defining a reasonable set of standard values is necessary. The convention used is based on what are called E series, which are approximately logarithmic divisions of a decade. Table 2.1 gives the values of the E12, E24, E48, E96, and E192 series, which are the most commonly used series for resistors. The E12 series divides 1 decade into 12 values, the E24 series divides 1 decade into 24 values, and so on. The E3 and E6 series are seldom used for resistors and are not shown here. The E3 series contains every other value from the E6 series, which contains every other value from the E12 series, which contains every other value from the E24 series. Similarly, the E48 series contains every other value from the E96 series, which contains every other value from the E192 series. The E24 series does not contain every other value from the E48 series, because E48 values have three significant digits, whereas E24 values have only two. But one can say that the E24 series contains rounded-off values from the E48 series. The resistance of a resistor from any particular E series consists of a number from the series, multiplied by an integer power of ten. For example, the value 133 appears in the E48 series, so one can readily obtain resistors having nominal resistances of (e.g.) 133 O; 13:3 kO; and 1:33 MO: Every standard (off-the-shelf) resistor value equals the product of a number from an E series and an integer power of ten, but not all such values are necessarily available from a higher or lower series. For example, one can buy 10% and 5% (E12 and E24) resistors having values of 33, 330 O, 3.3 kO, and so on, but none of these values are available
30
2 Current, Voltage, and Resistance 2 μm
200 nm 2 μm
Fig. 2.14 Illustrating calculation of sheet resistance
200 nm
10 μm
1 μm = 1000 nm
5 squares
5 squares
the specified value is 62 kO. The value from the E48, E96, and E192 series nearest to the specified value is 61.9 kO. Fig. 2.15 Trimmed thin-film resistor
in the higher-precision (E48, E96, and E192) series. As another example, resistors having values 383 10n O; with n ¼ 1; 0; 1; 2; are available in the E48, E96, and E192 series, but not in the E12 or E24 series. A standard tolerance is associated with each value from an E series. Standard tolerances for off-the-shelf resistors are 20% (E6 – rarely used, nowadays), 10% (E12), 5% (E24), and 1% (E96). Standard tolerances for high-precision resistors (obtainable from some large suppliers and manufacturers) are 0:5%; 0:1%; and 0:05%: Resistors having tolerances as tight as 0:001% are available in selected resistances from certain manufacturers. However, high-precision resistors are not bulk-produced in every value from any particular E series, but typically are produced in only certain values having wide application (e.g., in precision instrumentation and measurement systems). Some manufacturers can produce special-order resistors having virtually any nominal value, with tolerances of better than 0.05%. Ordering a batch of such resistors might be justified if a particular value and tight tolerance are required for a circuit being produced in quantity. Example 2.8. A calculation indicates that a resistor having resistance R ¼ 61:7 kO is needed in a certain circuit. Refer to Table 2.1 and give the nearest standard value from each series. Solution: The E12 value nearest to the specified value is 56 kO. The E24 value nearest to
Example 2.9. One kind of ammeter measures the current in a wire by measuring the voltage across a precision resistor called a shunt connected in series with the wire. In a particular case, the shunt has resistance R ¼ 0:05 O 0:05% and the voltage across the shunt is V ¼ 1:872 mV: What is the current I through the shunt? Solution: The current is in the range Imin I Imax ; where V 1:872 mV ¼ 37:421 mA; ¼ Rmax ð0:05 OÞð1:0005Þ V 1:872 mV ¼ 37:459 mA: ¼ ¼ Rmin ð0:05 OÞð0:9995Þ
Imin ¼ Imax
Exercise 2.11. A calculation indicates that a resistor having resistance R ¼ 50 kO 1% is needed in a certain application. What value would you specify and from which series?
2.9 Resistor Marking Axial-lead composition, coated wire-wound, carbonfilm, and metal-film resistors are color-coded for resistance and tolerance by either 4-band or 5-band codes
2.9 Resistor Marking Table 2.1 E series for standard resistor values E192 E96 E48 E24 0:5% 1% 2% 5% 100 178 316 562 100 316 100 10 101 180 320 569 102 324 105 11 102 182 324 576 105 332 110 12 104 184 328 583 107 340 115 13 105 187 332 590 110 348 121 15 106 189 336 597 113 357 127 16 107 191 340 604 115 365 133 18 109 193 344 612 118 374 140 20 110 196 348 619 121 383 147 22 111 198 352 626 124 392 154 24 113 200 357 634 127 402 162 27 114 203 361 642 130 412 169 30 115 205 365 649 133 422 178 33 117 208 370 657 137 432 187 36 118 210 374 665 140 442 196 39 120 213 379 673 143 453 205 43 121 215 383 681 147 464 215 47 123 218 388 690 150 475 226 51 124 221 392 698 154 487 237 56 126 223 397 706 158 499 249 62 127 226 402 715 162 511 261 68 129 229 407 723 165 523 274 75 130 232 412 732 169 536 287 82 132 234 417 741 174 549 301 91 133 237 422 750 178 562 316 135 240 427 759 182 576 332 137 243 432 768 187 590 348 138 246 437 777 191 604 365 140 249 442 787 196 619 383 142 252 448 796 200 634 402 143 255 453 806 205 649 422 145 258 459 816 210 665 442 147 261 464 825 215 681 464 149 264 470 835 221 698 487 150 267 475 845 226 715 511 152 271 481 856 232 732 536 154 274 487 866 237 750 562 156 277 493 876 243 768 590 158 280 499 887 249 787 619 160 284 505 898 255 806 649 162 287 511 909 261 825 681 164 291 517 919 267 845 715 165 294 523 931 274 866 750 167 298 530 942 280 887 787 169 301 536 953 287 909 825 172 305 542 965 294 931 866 174 309 549 976 301 953 909 176 312 556 988 309 976 953
31
E12 10% 10 12 15 18 22 27 33 39 47 56 68 82
as defined in Table 2.2. A 4-band code is used for resistors from the E24 and lower series. A 5-band code is used for resistors from the E48 and higher
Table 2.2 Resistor color codes Color Value Black 0 Brown 1 Red 2 Orange 3 Yellow 4 Green 5 Blue 6 Voilet 7 Grey 8 White 9 Gold Silver None
Multiplier 100 101 102 103 104 105 106 107 108 109 101 102
Precision 1% 2%
0.5% 0.25% 0.1% 0.05% 5% 10% 20%
series. The first band is closer to one end of the resistor than the last band is to the other. The first two bands denote the first two significant digits of the resistance. In a 4-band code, the third band is the multiplier, which is an integer power of ten, and the fourth band denotes the tolerance. In a 5-band code, the third band denotes the third significant digit, the fourth band denotes the multiplier, and the fifth band is the tolerance.
Example 2.10. Give the resistance of resistors marked as follows: (a) Red, violet, yellow, green; (b) red, violet, brown, orange, violet. Answers: (a) 270 kO 0:5%; (b) 271 kO 0:1%.
Exercise 2.12. Give the resistance of resistors marked as follows: (a) Yellow, orange, red, gold; (b) yellow, green, white, orange, violet. In addition to resistance and tolerance, properies of resistors include power-dissipation rating, self-heating coefficient (described in Chapter 5), maximum operating temperature, and temperature coefficient of resistance (described in the next section). Most manufacturers and vendors provide that information in datasheets for their offerings.
32
2 Current, Voltage, and Resistance
Exercise 2.13. Using a search engine of your choosing, do a search on “resistors” and locate several manufacturers’ web sites. Visit each site and examine the technical data they provide on their offerings. Identify the technologies that provide (a) the lowest temperature coefficient of resistance, (b) the highest precision, and (c) the highest power-dissipation ratings.
of resistivity versus temperature (both K and C) for silver (Ag), aluminum (Al), gold (Au), copper (Cu), and tungsten (W). For 200 K T 900 K (25 C T 673 C), resistivity is very nearly a linear function of temperature. Actually, the linear range for these metals extends from about 100 C to almost 1000 C. For a sufficiently small change DT in temperature, the derivative of resistivity with respect to temperature can be approximated by drðT Þ rðT þ DTÞ rðT Þ ffi ; dT DT
2.10 Variation of Resistivity and Resistance with Temperature Resistivities of materials and thus resistances of conductors and resistors vary with temperature.17 Temperature dependence of resistivities of certain metals is of interest because conductors in electric circuits are metallic. Figure 2.16 shows resistivity as a function of temperature for aluminum (Al), copper (Cu), and gold (Au).18 The scales on the axes are logarithmic. The vertical (resistivity) scale is logðr=r0 Þ; where r0 ¼ 108 O m (1 mO cm). The horizontal (temperature) scale is logðT=T0 Þ; where T0 ¼ 1K (one kelvin). For example, for logðT=T0 Þ ¼ 2; we have T=T0 ¼ 100 and the temperature is T ¼ 100 T0 ¼ 100 K: At that temperature, the resistivity of copper is given by logðr=r0 Þ ¼ 0:5; so r ¼ r0 100:5 ¼ 0:316 mO cm: The vertical reference line indicates T ¼ 298 K ¼ 25 C (77 F), where the values are rAl =r0 ¼ 2:709; rCu =r0 ¼ 1:712; and rAu =r0 ¼ 2:255: Figure 2.16 suggests that resistivity is very nearly a linear function of temperature for temperatures above about 102:25 K ffi 178 K; which is approximately 95 C: Operating temperatures at or above room temperature are common for linear circuits, so we are particularly interested in temperatures above about 298 K ¼ 20 C or so. Figure 2.17 shows graphs
17
Resistivity can also vary with pressure, strain, strength and direction of an applied magnetic field, and other things. The operation of various transducers (e.g., strain gauges) is based upon such effects. 18 Handbook of Chemistry and Physics (76th Ed.), edited by David R. Lide, CRC Press, 1995.
which gives, for the variation of resistivity with temperature, drðT Þ DT dT ¼ rðT Þ½1 þ aðT Þ DT ;
rðT þ DTÞ ffi rðT Þ þ
(2.20)
where að T Þ ¼
1 drðT Þ rðT Þ dT
(2.21)
is the temperature coefficient of resistivity at temperature T. In engineering applications of (2.20), temperature T often is expressed in degree Celsius and resistivities of materials and the associated temperature coefficients are commonly specified at T25 ¼ 25 C ¼ 298 K. In such applications it is usual to specialize (2.20) and write ^ T ¼ r25 ½1 þ a25 ðT T25 Þ ; r
(2.22)
where T25 ¼ 25 C ¼ 298 K; the parameters r25 ; a25 are the resistivity and temperature coefficient, respec^T is an approximation to the true tively; and r (measured) resistivity at temperature T. For many metals (2.22) can be used to estimate resistivity over a wide range – from about 100 C to almost 1000 C. The numerical value of a temperature coefficient is the same whether expressed in C1 or K1, because the quantity T T25 in (2.22) is the same, whether both temperatures are expressed in degree Celsius or Kelvin. In practice (e.g., on component data sheets), temperature coefficients are commonly expressed in parts per million (ppm), which is 106 K times the coefficient expressed in K1 (or C1 ):
2.10 Variation of Resistivity and Resistance with Temperature
33
1 0.5
Al
0
Cu
–0.5
log
ρ
–1
ρ
–1.5
Au
0
–2 –2.5
Fig. 2.16 Graphs of resistivity versus temperature (log-log scale) for pure aluminum (Al), copper (Cu), and gold (Au), where r0 ¼ 108 Om ¼ 1 mOcm and T0 ¼ 1 K: (See Footnote 18)
T = 298 K
–3 –3.5 –4
0
0.25 0.5 0.75
1
1.25 1.5 1.75
log
2
2.25 2.5 2.75
3
T T0
25
20 W 15 r (μΩ cm) 10 Al
Au Cu
5 Ag
Fig. 2.17 Resistivities of selected metals (See Footnote 18)
0 200 –73
a ðppmÞ ¼ a K1 106 K:
300 27
400 127
500 227
600 327
700 427
800 527
900 (K) 627 (°C)
T
(2.23)
Table 2.3 gives resistivities and temperature coefficients at 25 C for selected metals. Be aware that such data are available from many sources, and temperature coefficients in particular can vary significantly from one source to the next. Also, the values in Table 2.3 are for pure metals, whereas wires and cables used in electrical components and apparatus often are alloys whose resistivities and temperature coefficients can
differ significantly from those for the dominant pure metal. The data given in Table 2.3 are intended for use only in examples and problems given in this book, not for actual engineering design. Figure 2.18 shows graphs of the percent error versus temperature for resistivities calculated using (2.22), calculated as errorðT Þ ¼ 100
^ T rT r rT
(2.24)
34
2 Current, Voltage, and Resistance
Table 2.3 Resistivities and selected metals19 Metal Resistivity at 25 C ð mO cmÞ Silver (Ag) 1.62 Aluminum (Al) 2.71 Gold (Au) 2.26 Copper (Cu) 1.71 Tungsten (W) 5.39
temperature coefficients for Temperature coefficient at 25 C (K1) 4:053 103 4:438 103 4:022 103 4:138 103 4:849 103
Temperature coefficient at 25 C (ppm) 4053 4438 4022 4138 4849
For temperatures between 298 K (25 C) and 898 K (625 C), the maximum error (magnitude) is less than 5%. For that range of temperatures, the maximum error (magnitude) for copper (a popular material for wires) is approximately 2%.
Exercise 2.15. The resistivity of a certain metal is 1:6 108 O m at 10 C and 2:0 108 O m at 70 C. Estimate the temperature coefficient of resistivity for the metal at 10 C. The resistivities of materials used to make resistors also vary with temperature. Such variation is approximately linear over the range of operating temperatures for any particular resistor. In practice, it usually is more convenient to deal directly with resistance than resistivity. For any particular resistor, resistance is proportional to resistivity, so (2.22) gives RT ¼ R25 ½1 þ a25 ðT T25 Þ :
Exercise 2.14. Refer to Fig. 2.18. Why is the error at 298 K equal to zero for all four linear approximations?
Example 2.11. A copper wire is heated from 25 C to 100 C. What is the percent increase in resistivity? Solution: From Table 2.3, the resistivity and temperature coefficient for copper at 25 C are r25 ¼ 1:71 mO cm and a25 ¼ 4;138ppm; respectively. From (2.22), the resistivity at 100 C is r100 ¼ r25 ½1 þ a25 ðT T25 Þ ¼ ð1:71 mO cmÞ½1 þ 4;138 106 C1 ð100 C 25 CÞ ¼ 2:24 mO cm: The percent increase is 100
19
r100 r25 ffi 31%: r25
Ibid. The temperature coefficients were obtained from the slopes of linear-least-squares fits to the resistivity data given there.
(2.25)
In view of (2.25), the temperature coefficient of resistivity is also called the temperature coefficient of resistance, usually called just the temperature coefficient or abbreviated as TCR. Temperature coefficients for resistors vary considerably. Generally, carbon composition and carbon-film resistors have temperature coefficients on the order of 103 K1 ; whereas wirewound and some metal-film and metal-oxide resistors have temperature coefficients on the order of 105 K1 : In general, resistances of wirewound, metal-film, and metal-oxide resistors are much less sensitive to temperature than carbon-film and carbon-composition resistors. The resistivities of many materials approach zero (the materials become superconductors) at temperatures approaching 0 K. The resistivity of a superconductor is less than 1022 O cm; whereas the lowest (room temperature) resistivity found in metals is on the order of 106 O cm: Thus resistivities for superconductors are about a factor of 10 -16 smaller than those of materials ordinarily used for conductors in electric circuits. Some materials become superconductors at temperatures near 77 K (the boiling point of nitrogen), which are much easier to attain and maintain than those near absolute zero. As of this writing, use of superconducting materials is limited to a few specialized applications.
2.11 American Wire Gauge (AWG) and Metric Wire Gauge (MWG)
35
1.5 1 0.5
Ag
0 –
–
error(%)
–
–
Cu
2
W
3
3.5 –
–
Au
2.5 –
Fig. 2.18 Percent error in a linear approximation to resistivity as a function of temperature for five metals. See (2.24). The curves are not smooth because each contains only 11 data points
1
1.5 –
–
Al
0.5
4
4.5 298 25
Table 2.4 American wire gauge and wire diameters AWG 6 8 10 d (mm) 4.115 3.264 2.588
398 125
598 325
698 425
798 525
898 (K) 625 (°C)
18 1.024
20 0.813
T
12 2.052
2.11 American Wire Gauge (AWG) and Metric Wire Gauge (MWG) In the United States, the size of wire is specified by a whole number called gauge (AWG, or American wire gauge). Table 2.4 gives the diameters of selected AWG wires. The diameter of any AWG wire is given by DAWG ¼ 8:251eð0:1159ÞAWG mm:
498 225
14 1.628
Example 2.12. The diameter of AWG 18 wire is
22 0.643
The resistance of a length L (m) of AWG copper wire is given by RCu ffi 320 106 O m1 L eð0:232Þ ðAWGÞ :
(2.27)
For other materials, use R¼
(2.26)
For AWG 00, 000, and 0000 sizes, use AWG ¼ 1; 2; 3; respectively, in (2.26).
16 1.290
r RCu : rCu
(2.28)
Example 2.13. The resistance of 1 km of AWG 000 copper wire is RCu ffi 320 106 O m1 ð1kmÞ eð0:232Þð2Þ ffi 0:201 O:
D18 ¼ 8:251 mm eð0:1159Þð18Þ ¼ 1:024 mm and the diameter of AWG 000 wire is D000 ¼ 8:251 mm eð0:1159Þð2Þ ¼ 10:404 mm:
and the resistance of 1 km of AWG 000 aluminum wire is RAl
r ¼ Al RCu ¼ rCu
2:709 ð0:202 OÞ ¼ 0:320 O: 1:712
36
2 Current, Voltage, and Resistance
Exercise 2.16. The diameter of a certain wire must be at least 5 mm. What is the largest possible AWG designation of a wire meeting this requirement? In Europe, wire size is specified by diameter in mm or less often by metric wire gauge (MWG), which is ten times the diameter in mm. For example, the diameter of MWG 30 wire is 3 mm. Simply specifying wire diameter in mm seems to make a great deal of sense. However, an advantage of the AWG convention is that equal steps in AWG designation correspond to equal resistance ratios; for example, if decreasing the AWG designation of a certain kind of wire from 22 to 20 decreases the resistance of the wire by a factor of 0.6, then so would a decrease from 20 to 18, or 18 to 16, and so on. Exercise 2.17. What is the MWG designation for AWG 18 wire?
2.12 DC and AC Historically, dc and ac arose as abbreviations for direct current and alternating current, respectively, where direct was synonymous with constant and alternating was synonymous with sinusoidal. Nowadays, dc and ac are applied to either current or voltage. Thus folks speak of dc voltage, despite the seeming contradiction, or ac current, despite the seeming redundancy. Furthermore, ac is commonly used to mean a time-varying (not just sinusoidal) current or voltage. But for the present, we use ac as a synonym for sinusoidal. Sinusoidal currents and voltages are especially important in electrical engineering, for reasons you will come to understand as you progress through this book and the rest of your curriculum. We may regard a dc current or voltage as a sinusoidal current or voltage having frequency f ¼ 0 ; e.g., if f ¼ 0, then V cosð2pf tÞ ¼ V cosð0Þ ¼ V: Conventionally, constant currents and voltages and constant parameters having the dimensions of
current or voltage are denoted by capital letters; e.g., I ¼ 20 mA or V ¼ 5 V: Time-varying currents and voltages are denoted by lower-case letters; e.g., iðtÞ ¼ I cosð2pf tÞ and vðtÞ ¼ V cosð2pf tÞ; where the current i and the voltage v vary with time and the parameters I and V are constant. Most circuit components respond differently to ac than to dc. In particular, the resistance of a conductor (such as a wire) is larger for a rapidly varying current than for one that varies more slowly or is constant. The resistance of a conductor carrying a sinusoidal current increases with the frequency of the current, as described in the next section.
2.13 Skin Effect and Proximity Effect In this section, we use R (script) to denote radius of a cylindrical conductor and R (italic) to denote resistance. Refer to Fig. 2.19, which shows (qualitatively) a cross section of a conductor carrying a sinusoidal current i ¼ I cosð2pf tÞ and above that, a graph illustrating (again qualitatively) how the current is distributed in the conductor. The abscissa is radial distance from the center of the conductor and the ordinate is current density J, which is current per unit J (r) J0
J0
Jdc =
0
Fig. 2.19 An illustration of skin effect
r
I A
2.13 Skin Effect and Proximity Effect
37
cross-sectional area. At dc (for f ¼ 0), the total current I is uniformly distributed across any diameter, as indicated by the dashed line at J ¼ I/A, where A ¼ p R2 is the cross-sectional area of the conductor. As the frequency of the current is increased, the current density becomes non-uniform, being greater at the surface of the conductor than at the center. At sufficiently high frequencies, most of the current is concentrated in a relatively thin concentric layer of material near the surface. This phenomenon is called skin effect. Under conditions described below, the current density J at a distance r from the center of a cylindrical conductor is given by J ðr Þ ¼ J0 eðRrÞ=dð f Þ ; 0 r R;
(2.30)
where r is the resistivity of the material (O m), m0 ¼ 4p 107 Hm1 is the permeability of a vacuum, and mr is the relative permeability of the material (dimensionless). For non-magnetic materials, such as copper and aluminum, mr ¼ 1: From (2.29), skin depth is the distance from the surface of a conductor at which the current density in the conductor is e1 ffi 0:37 times the value at the surface. Skin effect concentrates current near the surface of a conductor, reducing the effective cross-sectional area A in the relation R ¼ rl=A and thereby makes the resistance of a conductor larger for a sinusoidal current (ac resistance) than that for a constant current (dc resistance). In what follows, we obtain an expression for the ratio of ac resistance to dc resistance. The (total) current in a conductor having crosssectional area A is given by ð i¼
JdA; A
i¼
(2.31)
ð 2p ð R 0
J ðr; yÞr dr dy;
(2.32)
0
where i is the current in the conductor at any particular time and J ðr; yÞ is the current density over a cross section of the conductor at the same time. From (2.29) and (2.32),
(2.29)
where R is the radius of the conductor, J0 is the current density at the surface of the conductor, and f is the frequency of the time-varying current. The parameter dð f Þ in (2.29) is a function of frequency called skin depth, given by rffiffiffiffiffiffiffiffiffiffiffiffiffiffi r ; dð f Þ ¼ pf mr m0
where J (A m2) is the current density over the cross section. In words, the total current i in a conductor is obtained by integrating the current density J over a cross-sectional area A of the conductor. For a cylindrical conductor (a wire) having radius R; we may express (2.31) in polar coordinates as
i¼
ð 2p ð R 0
J0 eðRrÞ=d r dr dy
0
¼ 2pJ0 eR=d
ðR
er=d r dr
0 R=d 2
d þ RdeR=d d2 eR=d ¼ 2pJ0 e
¼ 2pJ0 d2 eR=d þ Rd d2 d R=d 1 : ¼ 2pJ0 Rd 1 þ e R
(2.33)
For R d; (2.33) reduces to i ffi 2pJ0 Rd;
(2.34)
which is exactly what we would obtain if the current density were uniform and equal to J0 in a hollow tube having outer radius R and inner radius R d (wall thickness d). We can show this as follows. If the current density were given by J ðr Þ ¼
J0 ; 0;
R d
(2.35)
then the current would be given by 2 R r i¼ J0 r dr dy ¼ 2pJ0 2 Rd 0 Rd h i ¼ pJ0 R2 ðR dÞ2 ¼ pJ0 2dR d2 d ffi 2pJ0 Rd; R d; ¼ 2pJ0 Rd 1 2R ð 2p ð R
38
2 Current, Voltage, and Resistance
which agrees with (2.34), as claimed above. It follows that the effective cross-sectional area seen by a current in a cylindrical conductor is the cross-sectional area of the tube described above, given by h
ratio of ac resistance Rac to dc resistance Rdc for a cylindrical conductor having diameter D ¼ 2R is given by Rac D2 ; ffi Rdc 4dðD dÞ
i
A ¼ p R2 ðR dÞ2 ¼ 2pRd pd2 ¼ pdð2R dÞ: (2.36) For R d; (2.36) gives A ffi 2pRd:
(2.37)
If the radius of a cylindrical conductor is much larger than the skin depth, skin effect appears to reduce a solid cylindrical conductor having radius R to a tubular conductor having outer radius R and inner radius R d: Whereas the actual cross-sectional area of a conductor having radius R – that seen by a dc current – is Adc ¼ pR2 ; the effective cross-sectional area seen by an ac current is given by (2.36). Consequently, the ratio of ac resistance to dc resistance for the conductor is given by Rac rl rl 1 Adc pR2 R2 ¼ : ffi ¼ ¼ Rdc Aac Adc Aac pdð2R dÞ dð2R dÞ (2.38) It is conventional to describe wires in terms of diameter D, rather than radius R. From (2.38), the
(2.39)
where d ¼ dð f Þ is skin depth, given by (2.30). Figure 2.20 shows a graph of this ratio versus frequency for five American wire gauge (AWG) sizes of copper wire at T ¼ 25 C (77 F). The fact that current density decreases exponentially with distance from the surface as er=d suggests that (2.39) provides a good approximation to Rac =Rdc if the radius of the conductor exceeds three skin depths. Taking D ¼ 6d ðR ¼ 3dÞ in (2.39) gives Rac ð6dÞ2 36 ¼ 1:8; ¼ Rdc 4dð6d dÞ 20
(2.40)
which means that the curves in Fig. 2.20 are valid above the horizontal line at Rac =Rdc ¼ 1:8: Also, the ac resistance must approach the dc resistance at low frequencies, so the curves must approach unity, somewhat as shown, for frequencies approaching zero. Finally, there is no reason for the curves to make other than a smooth transition from their behavior above 1.8 to their behavior for frequencies approaching zero. In other words, the curves in
AWG
dia (mm)
1000 6 10 14 18 22
100 Rac Rdc 10
1.8
Fig. 2.20 Ratio of ac to dc resistance versus frequency for a 1-m length of each of five wire sizes (copper at 25 C)
1 103
104
105
106 f (Hz)
107
108
109
4.115 2.588 1.628 1.024 0.643
2.13 Skin Effect and Proximity Effect
39
Fig. 2.20 cannot be too far wrong, even for skin depths larger than one-third of a radius (below the line at Rac =Rdc ¼ 1:8). Figure 2.20 illustrates the fact that the ratio of ac to dc resistance increases with wire diameter. You might conclude from this that countering skin effect in any particular case requires using smaller wire. However, this is not the case, because dc and ac resistance (individually) decrease with increasing wire diameter (decreasing AWG designation). The ratio Rac =Rdc can be expressed in terms of AWG wire sizes, as follows. From (2.39) and (2.26), Rac DAWG 2 ffi ; Rdc AWG 4dðDAWG dÞ DAWG ffi 8:251eð0:1159ÞAWG mm:
(2.41)
Exercise 2.18. The dc resistance of a 1-m length of AWG 22 wire at 25 C is 0:0526 O: (a) What is the ac resistance of the wire at (i) 10 MHz and 25 C? (ii) At 1 GHz and 25 C? (b) Repeat for a 1-m length of AWG 20 wire at the same temperature and made from the same material. For a non-magnetic material, mr ¼ 1: In that case, a useful expression for skin depth is obtained by expressing resistivity r in mO cm and frequency f in MHz. With these adaptations (2.30) can be written rffiffiffiffiffiffiffiffiffiffi r dð f Þ ¼ pf m0 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffisffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1mO cm r=ð1mO cmÞ ¼ 7 1 ðpÞ 4p10 Hm ð1 MHzÞ f =ð1 MHzÞ and finally as sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi r=ð1mO cmÞ dð f Þ ¼ d ; f =ð1 MHzÞ sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1mO cm ¼ 50:33 mm: d¼ 7 ðpÞ 4p10 Hm1 ð1 MHZÞ (2.42)
For example, the resistivity of aluminum at 25 C is r ¼ 2:71 mO cm; so the skin depth of aluminum at 25 C and 100 MHz is sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi r=ð1mO cmÞ d¼d f =ð1 MHzÞ sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ffi 2:71 ¼ ð50:33 mmÞ ¼ 8:29 mm 100 and the skin depth of copper under the same conditions is sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi r=ð1mO cmÞ d¼d f =ð1 MHzÞ sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ffi 1:71 ¼ 6:58 mm ¼ ð50:33 mmÞ 100 Figure 2.21 shows graphs of skin depth versus frequency for copper and aluminum at 25 C. At 25 C, skin depth in an aluminum conductor is about 25% larger than that in a copper conductor. Example 2.14. Assume the relations derived in this section involving ac and dc resistance require D 6 dð f Þ: Derive an expression for the minimum frequency at which the formulas are valid for copper wire at 25 C. Construct a graph of the minimum frequency versus AWG wire size for 0 AWG 22: Compare your results with Fig. 2.20. Solution: From (2.42), the skin depth of copper at 25 C and frequency f is given by sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1:71 mm dð f Þ ¼ 50:33 f =ð1 MHzÞ 65:82 ¼ pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi mm: f =ð1 MHzÞ If we require D 6dð f Þ; then 65:82 D dð f Þ ¼ pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi mm 6 f =ð1 MHzÞ 2 f 395 mm ) 1 MHz D
40
2 Current, Voltage, and Resistance 104
103 δ ( f ) (μm)
Al 100 Cu
10
1 103
Fig. 2.21 Skin depth versus frequency for aluminum and copper at 25 C (77 F)
From (2.41), the diameter of an AWGdesignated wire is given by DAWG ¼ 8:251eð0:1159ÞAWG mm ¼ 8251eð0:1159ÞAWG mm; and so we require f 1 MHz
395
2
8251eð0:1159ÞAWG
) f 2:292eð0:2318ÞAWG kHz: Figure 2.22 shows a graph of the minimum frequency given above versus AWG wire size. Computed values below are in good agreement with the frequencies at which the lines in Fig. 2.20 intersect the line Rac =Rdc ¼ 1:8 AWG Minimum Frequency (kHz)
6 10 14 18 22 9.21 23.3 58.9 149 376
Exercise 2.19. Construct graphs (on the same axes) of skin depth versus frequency for copper
104
105
106 f (Hz)
107
108
109
for T ¼ 0 C and T ¼ 100 C and for 1 kHz f 1 GHz: Use logarithmic scales on the axes, as in Fig. 2.21. Not all conductors are cylindrical. For example, conductors in integrated circuits are more nearly rectangular (in cross section). Skin-effect calculations for conductors in integrated circuits (IC’s) can be complicated. For one thing, IC’s are built in layers, so conditions above and below a conductor can be different, and skin depths can differ significantly on different surfaces of such a conductor. Typically, about all one would attempt is to determine the theoretical skin depth in relation to conductor cross-section dimensions. As of this writing, the frequencies of operation of IC’s and the dimensions of conductors in IC’s are such that skin effect is negligible. Example 2.15. A copper conductor in a certain high-speed integrated circuit has an approximately rectangular cross section with height h ¼ 50 nm and width w ¼ 25 nm. The highest frequency of interest is f ¼ 30 GHz and the operating temperature is T ¼ 100 C: Is skin effect significant? If not, at what frequency would skin effect become significant?
2.13 Skin Effect and Proximity Effect
41
103
100
fmin (kHz)
10
1
0
2
4
6
8
10
12
14
16
18
20
22
AWG Fig. 2.22 Graph of Example 2.14
(a) currents in opposite directions
(b) currents in the same direction
Fig. 2.23 Illustrating proximity effect
Solution: The resistivity of copper at 100 C is r100 ffi r25 ½1 þ a25 ð100 C 25 CÞ
ffi ð1:71 mO cmÞ½1 þ 4138 106 Þð75Þ ffi 2:24 mO cm: The skin depth at 30 GHz is sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi r=ð1mO cmÞ d¼d f =ð1 MHzÞ rffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2:24 ffi ð50:33 mmÞ ffi 435 nm; 30 103 which is much larger than the largest dimension of the conductor, so skin effect is insignif-
icant. For skin effect to be significant, the skin depth must be on the order of the largest dimension. The corresponding frequency is sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2:24 ffi 50 nm ð50:33 mmÞ f =1 MHz ) f ffi 2:27 THz; which lies in the infrared region of the electromagnetic spectrum. The proximity effect, like the skin effect, is a essentially a manifestation of the facts that (1) a moving charge creates a magnetic field and (2) a magnetic field exerts a force on a moving charge. As a result, currents parallel to and in proximity to one another exert forces on each other. The proximity effect distorts the current density in conductors running sideby-side. If the currents in a pair of parallel conductors are in opposite directions, the current will be concentrated in the halves of the conductors farthest from each other, as illustrated by Fig. 2.23(a). If the currents in a pair of parallel conductors are in the same
42
direction, the current will be concentrated in the half of the each conductor nearest the other, as illustrated by Fig. 2.23(b). The proximity-effect force on a current is also felt by the conductor carrying the current. The force can be quite large, and in some industrial plants where conductors carrying large currents are side by side, it is necessary to strap the conductors down to keep them in place. The proximity effect, like the skin effect, increases with the frequency of the current, causing an increase in effective resistance with frequency because the conducting electrons are crowded into smaller and smaller cross-sections of each conductor. In some tightly wound multilayer coils, such as found in transformers and inductors,20 current crowding caused by the proximity effect can cause an increase in resistance with increasing frequency that is as great or even greater than that caused by skin effect. Expressions for the combined influence of proximity effect and skin effect are complicated and derivations of such expressions are beyond the scope of this text. Our purpose in introducing these phenomena is primarily to describe why the resistance of a conductor increases with the frequency of a sinusoidal current through the conductor. Problems at the end of the chapter that call for quantitative analyses of ac resistance consider only skin effect.
2 Current, Voltage, and Resistance
2.15 Problems
Section 2.1 is prerequisite for the following problems. P 2.1 The peak current in a strong lightning bolt is about 250 kA and persists for about 150 ms. Assuming the cloud is positively charged and that only electrons are involved in the current, approximately how many electrons are transferred and in which direction? P 2.2 In a certain medium, electrons pass from left to right through an imaginary plane at the rate 1020 electrons per second and singly-charged positive ions pass from right to left at the rate 1020 ions per second. What is the current (magnitude and direction) through the plane? P 2.3 A 1.5 V alkaline D cell (flashlight battery) can provide a current of 100 mA for about 80 h. How much charge exits the positive terminal during that time? P 2.4 The table below shows ampere-hour (Ah) ratings of three types of 9 V batteries commonly advertised as alkaline, heavy-duty, and generalpurpose. Alkaline batteries cost about 75% more than heavy-duty batteries and 130% more than generalpurpose batteries. Which is the cheapest per amperehour delivered? By what factor?
2.14 Concluding Remark
Battery type (all are 9 V) Alkaline Heavy duty General purpose
Practicing circuit designers must be aware of E-series standard values, temperature-dependence of resistance, skin effect, and many other things. But including all of these details in every example and problem in this introductory book would obscure the main point of the example or problem. Unless standard value and tolerance are an essential part of an example or problem, we treat resistors as if they can have any value whatever. Unless variation of resistance with temperature or frequency is an essential part of an example or problem, we ignore those effects, as well.
P 2.5 The table below shows ampere-hour rating, mass, and approximate cost (circa 2009) for four sizes of alkaline batteries. Which is the cheapest per ampere-hour? Which is the most effective in terms of mA h g–1? If a remote control uses 2 AA batteries and has a mass of 100 g with the AA batteries in, what would the mass be if it used D cells? What would it weigh in both cases?
20
We treat transformers and inductors in Chapter 9.
Size AAA AA C D
mAh 400 1000 3200 8000
mAh at 10 mA 470 180 160
Mass (g) 12 22 64 125
Cost ($) 0.94 0.94 1.29 1.29
2.15 Problems
43
P 2.6 A 3 V lithium button battery is rated at 150 mAh and will last approximately 1 year when used as a memory backup battery in a desktop computer, depending upon how much the computer is used (the battery is used only while the computer is off). If the computer is on 8 h/day 7 days/week and the battery lasts 1 year, what is the idle current drawn by the memory? P 2.7 For t > 0; the charge to the right of an infinite plane is given by qðtÞ ¼
0; t < 0; q0 1 et=t ; t > 0;
where q0 ¼ 100 mC and t ¼ 2 ms: (a) Obtain an expression for the current through the plane from right to left. (b) Compute the values of the current for t ¼ 0; t ¼ 1ms; and t ¼ 10 ms: P 2.8 For t > 0; the current inward through the surface of a sphere is given by iðtÞ ¼
0; t < 0; i0 1 et=t Þ; t > 0;
where i0 ¼ 2 mA and t ¼ 1 ms: The charge inside the sphere is zero for t ¼ 0: Find the charge inside the sphere for t ¼ 1 ms and t ¼ 5 ms: P 2.9 The automatic cannon on a certain fighter aircraft fires N rounds per second. If each bullet carries a charge q, what is the current at the muzzle of the gun? P 2.10 The current in a wire is I ¼ 5 A. If the current is due entirely to electron flow, how many electrons pass through a fixed cross section of the wire in 1 s? P 2.11 An electric current is established in an electrolyte, as shown in Fig. P 2.1. Positive ions drift to the left and the negative ions drift to the right. During each interval T, n1 singly charged ions and n2 doubly
–
Battery
– + – +
Fig. P 2.1 See Problem P 2.11
q ¼ q0 cosð2 p f tÞ; where q0 ¼ 5 mC and f ¼ 1; 000 s1 : What is the current from right to left through the surface? P 2.13 Repeat Problem P 2.12 for q¼
0; t < 0; q0 et=t ; t 0;
with q0 ¼ 5 mC and t ¼ 1 ms. P 2.14 The current required to change the state of one bit in a certain memory chip is on the order of 1 mA. The time required to change the state is 15 ns. How much charge is involved? How many electrons? P 2.15 Suppose the current through the starter on an automobile is about 75 A for 1.2 s and is due entirely to electron flow. About how many electrons pass through the starter in that time? If the voltage drop across the starter is 12 V, what is the work done by the electrons on the starter? P 2.16 The charge that passes through a surface in an interval t1 t < t2 is given by qðt2 Þ qðt1 Þ ¼ Dq ¼
ð t2 iðtÞ dt t1
Calculate the charge that passes through a surface in an interval 0 t < 1 ms if the current is given by (a) i ¼ I0 cosð2 p f tÞ with I0 ¼ 10 mA and f ¼ 1 kHz (b) i ¼ I0 et=t with I0 ¼ 5 mA and t ¼ 2 ms: Section 2.2 is prerequisite for the following problems.
I
+
charged ions reach each electrode. Obtain an expression for the current I. P 2.12 The net positive charge on the left side of a plane surface is given at any time t by
P 2.17 Assuming the proton (nucleus) and electron comprising an atom of hydrogen can be treated as point charges, calculate the force each exerts on the other when the atom is in its ground state. The (ground-state) mean distance from the nucleus (proton) to the electron is approximately 5:3 1011 m: P 2.18 Refer to Problem P 2.17. What is the electric field strength due to the nucleus at the ground-state distance of the electron from the nucleus?
44
2 Current, Voltage, and Resistance
P 2.19 Refer to Problem P 2.17. How much work is required to move the electron from its ground state to an infinite distance from the nucleus? Express the result in joules and in electron-volts. P 2.20 Imagine that a positive point charge Q1 is attached to a 30,000 kg truck and a negative point charge Q1 is attached to a crane 3 m above the truck. (a) What is the minimum magnitude of the charge that would lift the truck? (b) How much work is done in lifting the truck 2 m? (c) How fast is the truck moving when it reaches that height? P 2.21 A particle having charge q moves from point a to point b under the influence of an electric field E, directed from a to b. When the particle reaches point b, the electric field is reversed and the particle moves back to point a. What is the energy lost by the particle? Section 2.3 is prerequisite for the following problems. P 2.22 Using the fact that a voltage Vab equals work done per unit charge on charge moving from a to b, and assuming that the terminal voltage of a battery remains constant throughout the life of the battery (it doesn’t), calculate the total energy stored in each battery of Problem P 2.5. (The terminal voltage of each battery is 1.5 V.) P 2.23 A certain 12 V marine battery is advertised as an 800 A h battery. Calculate the total energy stored in the battery. If the battery weighs 30 lb, what is the energy density in SI units? P 2.24 The electric field strength at a point 5 m from a point charge is 200 V m–1. What is the magnitude of the charge? If the charge is positive, what is the electric potential at the point? P 2.25 An electron at rest is released at point a and travels in a straight line to point b 1 cm away, where the velocity of the electron is 106 m s1 . What is the voltage at point b with respect to point a? P 2.26 In a cathode-ray video tube, electrons are released at a heated cathode and accelerated toward the face of the tube. The potential at the face is about 25 kV greater than that at the cathode. If the initial velocity of an electron equals zero, what is the velocity of the electron when it strikes the face of the tube? P 2.27 Dry air at atmospheric pressure will ionize and conduct electricity (break down) in an electric field whose strength is on the order of 1 MVm–1. After
scuffing across a carpet under these conditions, you can draw a ¼ in. spark from your finger to a metal doorframe. Approximately what was the voltage from your fingertip to the doorframe just before the arc was struck? P 2.28 See Problem P 2.27. If a cloud from which a lightning-bolt originates is 4000 ft from the ground, what is the magnitude of the voltage from the cloud to the ground? P 2.29 The electric field strength 1.5 m from a point charge is 1.5 Vm–1, directed away from the charge. What is the electric potential at that point? P 2.30 The electric field strength between uniformly and oppositely charged infinite parallel plates 0.5 cm apart is 1 kVm–1. (a) What is the voltage on the positive plate with respect to the negative plate? (b) How much work is done if a 10 nC charge is moved from the negative to the positive plate? Is the work done on the field or by the field? P 2.31 The electric potential 2 cm from a point charge is 100 V. What is the magnitude of the charge? P 2.32 The electric potential a distance x from a 0.05 nC point charge is 50 V. What is the distance x? Section 2.4 is prerequisite for the following problems. P 2.33 A certain copper wire has resistance per unit length r ¼ 1mO m1 : A voltage v ¼ 1 mV is applied across a 10 m length of the wire. The resulting current is due entirely to electrons. How many electrons have passed through a cross section of the wire 1 ms after the voltage is applied? P 2.34 If 1019 electrons enter the left end of a 1-cm long piece of material each second and exit the right end having experienced a voltage rise of 5 V, what is the resistance of the piece of material? P 2.35 The resistance of a sample of material is 1.5 kO. (a) If the current through the sample is 3 mA, what is the voltage across the sample? (b) If the voltage across the sample is 6 V, what is the current? P 2.36 A voltage V is applied (end-to-end) to a cylindrical sample of material having length L and diameter D. Express the current through the cylindrical sample in terms of the electric field strength in the sample and the sample diameter. Show that the expression is dimensionally consistent.
2.15 Problems
45 v
V0 −I0 I0
i
−V0
Fig. P 2.2 See Problem P 2.37
P 2.37 Resistance as defined and discussed in this chapter is called static resistance, by which is meant that it is the ratio of a constant voltage to the resulting constant current. Dynamic resistance, on the other hand, is defined as the rate of change of voltage with respect to current; that is, if we denote dynamic resistance by r, then the dynamic resistance of a device is given by r ¼ dv=di; where v is the voltage across the device and i is the current through the device. With this in mind, refer to Fig. P 2.2, which shows a graph of voltage versus current for a certain hypothetical device. Draw graphs of the static resistance R and the dynamic resistance r of the device versus current. Section 2.5 is prerequisite for the following problems. P 2.38 The resistivity of a certain aluminum alloy used for electrical wire is 2:83 108 Om: What is the diameter of an aluminum wire that has the same resistance per meter as a copper wire whose diameter is 0.2 cm? P 2.39 The resistance of a cylindrical sample of material is R. Express the resistivity of the material in terms of the resistance, diameter, and length of the sample. P 2.40 Express the lengthwise current through a rectangular sample of material in terms of the resistivity of the material, the voltage applied to the sample, and the sample dimensions (length, height, width). Show that your expression is dimensionally consistent. Assuming that all other parameters are held constant, what happens to the current through the sample as the length of the sample is increased?
P 2.41 Refer to Problem P 2.36. Express the current through the sample in terms of the resistivity of the sample material, the cross-sectional area of the sample, and the electric field strength in the sample. Show that the expression is dimensionally consistent. P 2.42 The cost per unit weight of copper is about twice that of aluminum. At 20 C, the resistivity of copper is 1.71 mO cm, the resistivity of aluminum is 2.71 mO cm, the density of copper is 8.96 g cm–3, and that of aluminum is 2.70 g cm–3. An electric power company needs to construct a transmission line from a power plant to a substation 10 km from the plant. The number and therefore the cost of the line supports is directly proportional to the weight of the wire they must support. The voltage drop from end to end of the line must not exceed 400 V when the current is 25 A. Considering all these factors, which of the two materials should be used for the transmission line? P 2.43 The cold resistance of the tungsten filament in a 60 W incandescent light bulb is about 20 O: The diameter of the filament wire is about 50mm and the resistivity of tungsten (at 25 C) is about 5:39 mO cm: How long is the wire from which the filament is made? How is such a length of wire made to fit in such a small space? P 2.44 A metal pipe has inside diameter ri and outside diameter ro. Let r denote the resistivity of the metal and obtain an expression for the resistance per unit length of the pipe. P 2.45 A sample of a certain material is a disk having radius r and thickness d. Let r denote the resistivity of the material and obtain an expression for the resistance of the sample from one edge to another, where the contacts are at the endpoints of a diagonal. Hint: As you probably recall from physics (and as shown in Chapter 4), resistances in series add. Section 2.6 is prerequisite for the following problems. P 2.46 The resistance of a certain resistor is in the range R0 ð1 0:01bÞ; where R0 is the nominal resistance and b is the precision (or tolerance), expressed in %. (a) Express the corresponding range of values of the conductance in terms of R0 and b. (b) For R0 ¼ 1 kO; express the tolerances of the conductance in percent for b ¼ 1%; 5%; 10% and 20%. Under
46
2 Current, Voltage, and Resistance
what condition is the tolerance on the conductance approximately equal to b? (c) The voltage across a resistor having resistance 1 kO 20% is V0 ¼ 5 V: What is the range of possible values of the resulting current? If the current must be 5 mA 2%; what precision is required of the resistor? P 2.47 A voltage v(t) is applied to a sample of material for 0 t < t0 : Obtain an expression for the conductance G of the sample in terms of the net charge Q that exits the sample during this time, for (a) vðtÞ ¼ V0 ; (b) vðtÞ ¼ V0 expðt=tÞ; and (c) vðtÞ ¼ V0 sinðo tÞ. P 2.48 The cross-section of a sample of material is an equilateral triangle. Denote the base of the triangular cross-section by b, the length of the sample by L and the conductivity of the material by s. The voltage V across the sample and the resulting current I through the sample are known. Obtain an expression for the height of the sample in terms of the length, conductivity, applied voltage, and resulting current. Show that the expression is dimensionally consistent. Section 2.7 is prerequisite for the following problems. P 2.49 The resistivity of a certain tantalum nitride film resistor is r ¼ 250 mO cm at 25 C. The film is of uniform but uncertain thickness and width. The actual (measured) resistance at 25 C is 1.1 kO. The desired resistance is 1.2 kO, and is to be attained by trimming one edge of the film along its length and parallel to the opposite edge. By what percent must the width of the film be reduced? P 2.50 A certain thin film resistor is designed and fabricated assuming the resistivity of the film is 250 mO cm at the operating temperature. The true value is 232 mO cm at that temperature. If the fabricated resistor has precisely the correct dimensions, by what percent must the width of the film be reduced (by trimming) to achieve the desired resistance? P 2.51 A certain thin film resistor having uniform thickness and width is trimmed as shown in Fig. P 2.3. The film thickness is h and the resistivity of the material is r. (a) Express the new resistance in terms of the old and the dimensions shown on the figure. (b) Show that if w < l; Dw w; and Dl l; then a good approximation to the resistance after trimming is
l w Δl
Δw
Fig. P 2.3 See Problem P 2.51
1 sq
1 sq
1 sq
1 sq
1 sq
1 sq 2
1 sq
1 sq
1 sq
1 sq
1 sq
1 sq
1 sq 2
Fig. P 2.4 See Problem P 2.52
R ffi Rsheet
l DlDw þ 2 : w w
P 2.52 For large resistance values, thin film resistors often are built in zigzag fashion. In such geometries, corner squares count approximately as half squares, as illustrated by Fig. P 2.4, when computing resistance. Justify this approximation. (The correct value, obtained by modeling and analysis, is 0.558 square.)
Section 2.8 is prerequisite for the following problems. P 2.53 If two resistors R1, R2 have the same precision b; what is the precision of R1 R2 =ðR1 þ R2 Þ? Give both exact and first-order approximate relations. What are the actual and approximate precisions for b ¼ 0:05 (5%)? P 2.54 If two resistors R1, R2 have the same precision b; what is the precision of R1 =ðR1 þ R2 Þ? Give both exact and first-order approximate relations. What are the actual and approximate precisions for b ¼ 0:05 (5%)? P 2.55 Suppose your company is considering a standard offering of resistors whose values are separated by 0.2%; i.e., such that Rnþ1 ¼ 1:002Rn for any two consecutive values. Approximately how many
2.15 Problems
such values would be required to cover the range 1 O R 1 MO? Section 2.9 is prerequisite for the following problems. P 2.56 Give the nominal resistance and tolerance indicated by the following color codes: (a) Gray, red, green, silver (b) Green, blue, yellow, gold (c) Brown, black, orange, gold (d) Yellow, violet, green, red, violet (e) White, orange, brown, orange, violet (f) Green, brown, brown, orange, green
47
from T0. Obtain a linear approximation for the current through the material in terms of the temperature change DT; the temperature coefficient a and the applied voltage. P 2.63 The resistance of a certain resistor is given by R ¼ R0 ½1 þ aðT T0 Þ ; where T is the temperature of the resistor in degrees Celsius and T0 ¼ 25 C: A constant voltage V0 is applied to the resistor. After a short time, the current stabilizes at I0. Obtain an expression for the temperature of the resistor as a function of the current I0. P 2.64 Suppose a constant current I0 is forced through the resistor described in Problem P 2.63. After a short time, the voltage across the resistor stabilizes at V0. Obtain an expression for the temperature of the resistor as a function of the voltage V0.
P 2.57 Give the nominal resistance and tolerance indicated by the following color codes: (a) Red, yellow, orange, gold (b) Brown, green, brown, white (c) Red, violet, orange, white (d) Orange, brown, blue, black, white (e) Brown, orange, orange, red, brown (f) Red, brown, gray, orange, violet Section 2.10 is prerequisite for the following problems. P 2.58 The temperature coefficient of a metal film resistor is typically in the neighborhood of 25 ppm. What is the percent increase in the resistance of a metal-film resistor if the temperature of the resistor is raised from 25 C to 140 C? P 2.59 Show that if R1 and R2 have the same temperature coefficient, then the quantity R1/R2 is independent of temperature. P 2.60 Show that if R1 and R2 have the same temperature coefficient, then the quantity R1 =ðR1 þ R2 Þ is independent of temperature. P 2.61 Show that if R1 and R2 have the same temperature coefficient a, then the temperature coefficient of the quantity R1 R2 =ðR1 þ R2 Þ is also a. P 2.62 Suppose a particular material at temperature T0 has temperature coefficient of resistivity a. A sample of the material at the same temperature has resistance R0. A voltage v is applied to the sample, and the temperature is allowed to vary a small amount DT
Section 2.11 is prerequisite for the following problems. P 2.65 The conductance of a 1-m sample of 24 AWG wire is measured at 25 C, and is found to be 9.1 S. If the wire is made of either copper, aluminum, or gold, which is most likely? P 2.66 For a fixed length and kind of wire, by what factor does the resistance of the wire increase if the gauge (AWG) is increased from (a) 6 to 8? (b) from 8 to 10? (c) from 10 to 12? P 2.67 Let RN denote the resistance of a 1 m length of wire having AWG designation N. Show that the ratio RN =RNþk ; where k is any whole number, is a fixed function of k, independent of N. P 2.68 If the length of a certain wire must be doubled, but the resistance must remain the same, by what number must the AWG designation be decreased? P 2.69 In a certain application, the required size for a copper wire is AWG 12. For reasons of cost, it is desired to use an aluminum wire, instead. What should be the size (AWG) of the aluminum wire? Sections 2.12 and 2.13 are prerequisite for the following problems. P 2.70 (a) Show that if the diameter of a cylindrical conductor is much larger than the skin depth, the ratio of ac to dc resistance is approximately ðD þ dÞ=ð4dÞ:
48
(b) Show that the approximation of part (a) is more accurate than the (perhaps more obvious) approximation D=ð4dÞ: P 2.71 Obtain an expression for the skin depth d1 of a cylindrical conductor at frequency f1 in terms of the skin depth d0 at frequency f0. Assume the temperature of the conductor is fixed. P 2.72 A certain web site gives the following formula for the ac resistance of a wire: pffiffiffi Rac ¼ Rdc k f ; where (quoting the web page) “f is frequency of ac in MHz” and k is called the “wire gauge factor,” whose values for various AWG wire sizes are given in an accompanying table. (a) What is the SI unit of k? (b) The formula assumes that D d; where D is the wire diameter and d is the skin depth. Derive the formula from (2.39) in the text and obtain an expression for k. Show that the formula has the correct dimension. (c) What are the magnitudes of k for AWG 22 copper wire at 25 C and 100 C? (d) For what frequencies is the formula approximately valid for AWG 22 copper wire at 25 C? P 2.73 A certain coil is wound with 50 m of AWG 32 copper wire. What is the dc resistance of the coil at 25 C? If the increase in resistance with frequency is due entirely to skin effect, what is the ac resistance of the coil at 10 MHz and 25 C?
2 Current, Voltage, and Resistance
P 2.74 In a certain application, the temperature of a 22 AWG copper wire varies from 0 C to 100 C and the frequency of the current through the wire ranges from 3 to 30 MHz. What is the maximum percent increase in the ac resistance of the wire from the value at 0 C and 3 MHz? P 2.75 In integrated circuits (ICs), conductors are strips of metal, often aluminum or copper, having approximately rectangular cross section. At this writing (circa 2009), the smallest conductors are approximately 20 nm wide and 50 nm thick and the highest frequency of interest in digital IC’s is about 30 GHz. Assume an operating temperature of 100 C and calculate the skin depth for copper at 30 GHz. Is skin effect significant in such devices? P 2.76 As IC manufacturing technology advances, the smallest lines (minimum conductor widths) and thicknesses decrease and the achievable operating frequencies increase. Do these advances make skin effect more significant or less so? P 2.77 Electric utilities use large rectangular-crosssection copper conductors called bus bars to connect adjacent equipment in distribution substations. A 2500 A bus bar is about 10 mm thick and 200 mm wide. Calculate the skin depth of copper at 60 Hz and determine whether the bus bar could be thinner. Assume an operating temperature of 100 C. Ignore corners and the short edges.
Chapter 3
Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws
In this chapter, we define a few important circuit elements and introduce circuit diagrams. We describe how circuit diagrams are annotated; that is, how voltages and currents are denoted in a manner that permits and facilitates analysis. We present Kirchhoff’s laws, which are the fundamental laws of circuit analysis, and the principle of superposition, which is a powerful tool for analysis of linear circuits.
3.1 Schematics and Circuit Diagrams Components of a physical circuit are connected by wires or other physical conductors, such as foils on a printed-circuit board or metallic strips in integrated circuits. A schematic or wiring diagram is a picture showing how a physical circuit is constructed, where conductors are represented by lines and other components, such as transistors, are represented by standardized graphic symbols. A circuit diagram, on the other hand, depicts the mathematical relations that exist among various idealized circuit elements, which individually or in groups, comprise mathematical models for physical circuit components. For the present, we may regard a circuit diagram as an abstraction of a schematic (wiring diagram). But keep in mind that schematics and circuit diagrams are different things. The various parts of a schematic are in one-to-one correspondence with the components they represent; that is, each symbol in a schematic stands for a physical component in the associated physical circuit. On the other hand, a circuit diagram is composed of mathematical models for physical components. A model for a single physical
component (such as a transistor) may consist of more than one circuit element, or a few interconnected circuit elements can represent a larger number of physical components. Consequently, the individual circuit elements shown in a circuit diagram do not necessarily represent physical components. In some cases, the circuit diagram representing a physical circuit may look like the associated schematic, but in general, a circuit diagram represents a physical circuit only to the extent that results of mathematical analysis of the circuit diagram correctly describe the observed behavior of the associated physical circuit. A schematic is a guide for construction. A circuit diagram is a guide for analysis and design. To illustrate points made above, we refer to Fig. 3.1, which shows both a schematic and a circuit diagram for a simple transistor amplifier. In the circuit diagram of Fig. 3.1(b), the transistor (a component) has been replaced by an equivalent circuit model (a collection of idealized elements). At this point, do not be concerned with what the symbols mean, how the model is obtained, or how the circuit works. Instead, focus on these points: • The circuit model for the transistor does not look anything like a real transistor. Even if we dissect a transistor and examine the innards under a microscope, we will not find either of the two elements comprising the circuit model. The elements of the model are non-physical; nonetheless, the model describes the transistor, in the sense that mathematical analysis of the circuit diagram yields results in good agreement with the observed behavior of the actual amplifier (under normal operating conditions).
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_3, # Springer ScienceþBusiness Media B.V. 2011
49
50
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws transistor
+VCC RC
R1 transistor
C B
+
+
b ib C
B R1
R2
rp
+ RC
E vin E
vin
Fig. 3.1 (a) A transistor amplifier (schematic, or wiring diagram) and (b) an associated model (circuit diagram)
+
R2
RE
vout −
RE
−
vout
−
− (b) small-signal model
(a) transistor amplifier
• The number of elements in the circuit diagram exceeds the number of (physical) components in the schematic. The transistor is represented by one component (symbol) in the schematic and by two elements in the circuit diagram. Often, a single transistor is modeled by four or more elements. The elements in a circuit diagram are rarely in one-to-one correspondence with those in the associated physical circuit. • To the untrained eye, the circuit diagram (model) does not look like the physical circuit it represents. The elements in the circuit diagram are not interconnected in the same way as in the physical circuit. But again, a correct mathematical analysis of the circuit diagram would yield results in agreement with observed behavior of the physical circuit (under conditions for which the model is applicable). Where we refer to a circuit, unless otherwise noted, we are referring to a circuit diagram (mathematical model), not to a physical circuit or schematic. Likewise, where we refer to a circuit element, we are referring to an idealized mathematical model, not a physical circuit component. The distinction between the elements of a circuit diagram and the components of a (physical) circuit will become clearer as we progress. Because circuit analysis deals exclusively with analysis of idealized models, and for the sake of economy, we omit the adjective ideal when referring to circuit elements and circuit diagrams. It is understood, for example, that an element called a conductor is an ideal conductor, not a physical conductor (wire).
a
b
vab = Φ ( a ) − Φ ( b ) = 0
Fig. 3.2 The symbol for a conductor is a line. The voltage vab across the conductor equals zero, regardless of the current through the conductor
3.2 Conductors and Connections A conductor is an idealization of a physical conductor (e.g., a wire) and is represented by a line, as illustrated by Fig. 3.2. The defining property of a conductor is that the electric potential is the same everywhere on a conductor (and on all other conductors to which it is connected). In Fig. 3.2 the potential F (a) at the left end (point a) equals the potential F (b) at the right end (point b), or anywhere in between. The voltage vab across the conductor equals zero, regardless of the current through the conductor. In other words, the resistance of a conductor equals zero. In circuit diagrams, a connection of intersecting conductors is denoted by a heavy dot, reminiscent of a lump of solder. There is no such dot at the intersection of conductors that cross (viewed from above) but are not connected. Refer to the circuit diagram in Fig. 3.3, where lines represent conductors and boxes represent (unspecified) circuit elements. The conductor connecting elements 1 and 3 is connected at the point a to the conductor connecting elements 2 and 4. The electric potential (or the voltage with respect to some other point) is the same everywhere on both of those conductors. The conductor connecting elements 3 and 6 is not connected to the conductor connecting
3.3 Annotating Circuit Diagrams
51 4 no connection a
1
3
2
Fig. 3.3 A dot is used to indicate a connection, where two or more conductors (or other elements) are connected
6
connections
b
elements 4 and 5. The potentials on those conductors may be different.
5
c
i1
i3
a i2
3.3 Annotating Circuit Diagrams b
Currents are denoted in a circuit diagram by labeled arrows, as illustrated in Fig. 3.4. Subscripts are used to distinguish various currents from each other. An arrow indicates the positive direction of the associated current, which we are free to define and which therefore is not necessarily the actual direction of the current. In fact, in most interesting circuits, the magnitudes and directions of most currents change with time. A current whose direction (sign) changes with time cannot possibly be always in the direction of the associated arrow. Again, the arrow indicates the direction defined as positive, not necessarily the actual direction of the associated current. It’s like the arrow pointing north on a roadmap. The arrow defines what is meant by north, but does not imply that everyone always drives north. Voltages are denoted in circuit diagrams in three ways, as illustrated by Fig. 3.5 and explained below. In Fig. 3.5(a), points of interest (nodes) are labeled a, b, c and voltages can be specified unambiguously using double-subscript notation; e.g., as vab, vbc, and vac. If a particular point (node) is identified as the reference node, then some other voltages can be specified using single-subscript notation, where it is understood that the omitted second subscript is the reference point. For example, if the node c in Fig. 3.5(a) is specified as the reference node, then va ¼ vac and vb ¼ vbc. However, if point c is the reference, we cannot use single-subscript notation to denote vab because vab is not referred to point c (see (3.1), below).
Fig. 3.4 Representing currents in a circuit diagram a
+
b
v2
−
+
+
v1
v3
−
−
c
(a)
(b)
Fig. 3.5 Conventions for specifying voltages on a circuit diagram (see text)
In Fig. 3.5(b), voltages are specified using plusminus notation, where the – sign identifies the reference point and the þ sign identifies the point at which v is specified with respect to the reference. The þ/ marks are reference marks that define what is meant by a positive value of v, just as a and b in Fig. 3.5(a) are reference marks that define what is meant by a positive value of vab. If the point marked (þ) is at a higher potential than the point marked (), the associated voltage v is positive. If the reverse is true, v is negative. For example, v2 in Fig. 3.5(b) corresponds to vab in Fig. 3.5(a). All three conventions (double-subscript, singlesubscript, and þ/–) are widely used. Two or even all three of these notations might used in a single circuit diagram; for example, one voltage of interest might be specified using single-subscript notation and another using þ/– notation. Understanding all three notations
52
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws b
a
b
a
ref
Fig. 3.6 Conventions for designating a voltage reference point
(a) reference designation
is essential. Otherwise it is unnecessarily difficult to obtain and interpret equations describing circuits. A voltage symbol having a subscript is not necessarily an instance of what is defined above as singlesubscript or double-subscript notation. For example, the subscripts on the voltage symbols in Fig. 3.5(b) serve simply to distinguish each voltage from the others. The notation in use is þ/– notation, not singlesubscript notation, because the subscripts do not refer to labeled points in the circuit (and because the voltage symbols appear between polarity marks). When single-subscript notation is used, that is, when one point (or conductor) in a circuit is chosen as a reference and other voltages in the circuit are specified with respect to that point, we are in effect treating the reference point as if its potential were zero, but in fact we usually do not know that – nor do we care. Again, we are concerned with potential differences (voltages), not absolute potentials. The point chosen as the reference in a circuit diagram often is indicated (in this book) by the label ref, as illustrated in Fig. 3.6(a). Alternatively, the ground1 symbol shown in Fig. 3.6(b) may be used to denote the reference point, as illustrated in Fig. 3.6(c). We refer again to Fig. 3.5(a) to make another important point. If F(a), F(b), and F(c) are the electric potentials at points, a, b, and c, then by definition vac ¼ FðaÞ FðcÞ; vbc ¼ FðbÞ FðcÞ; vab ¼ FðaÞ FðbÞ:
1
a
−
v1
+
(c) alternative reference designation
b
c +
v2 d
−
Fig. 3.7 See Example 3.1
Such relations are needed often in writing equations that describe circuits. Example 3.1. In Fig. 3.7, the electric potentials at the labeled points are F(a) ¼ 520 V, F(b) ¼ 515 V, F(c) ¼ 505 V, and F(d) ¼ 500 V. Find the voltages vad, vab, vac and v2. Using point d as the reference, find va and vc. Solution: By definition and from (3.1) vad ¼ FðaÞ FðdÞ ¼ 520 500 ¼ 20 V; vab ¼ FðaÞ FðbÞ ¼ 520 515 ¼ 5 V; vac ¼ FðaÞ FðcÞ ¼ 520 505 ¼ 15 V; v2 ¼ vcd ¼ FðcÞ Fðd Þ ¼ 5 V If we select the point d as the reference point for all voltages and use single-subscript notation, we have va ¼ vad ¼ FðaÞ FðdÞ ¼ 20 V; vc ¼ vcd ¼ FðcÞ FðdÞ ¼ 5 V
It follows that vab ¼ vac vbc ;
(b) ground symbol
vba ¼ vbc vac ¼ vab :
(3.1)
So called because earth ground (the grounded part of an electrical receptacle) is often the reference point.
Exercise 3.1. With reference to Example 3.1, find the voltages vbd, vcd, vda, v1, vb (point d is the reference for the last).
3.5 Open Circuits and Short Circuits
53
3.4 Series and Parallel Connections
Exercise 3.2. Use the terms series and parallel to describe (in words) the connections shown in Fig. 3.10.
A point on a circuit element or in a circuit to which we connect or envision connecting something (e.g., another element or a measuring instrument) is called a terminal. A circuit element or circuit having only two accessible terminals is called a two-terminal element or a two-terminal circuit. Two or more two-terminal elements or circuits can be connected in series, as shown in Fig. 3.8(a), or in parallel, as shown in Fig. 3.8(b). The same current passes through elements in series and the same voltage exists across elements in parallel. Series and parallel connections are undefined for elements having more than two terminals.
3.5 Open Circuits and Short Circuits A pair of terminals brought out from a circuit but not connected to each other, either by a conductor or a circuit element, is said to be open or to form an open circuit. If the terminals are connected by a conductor, the terminals are said to be shorted or to form a short circuit. Figure 3.11 illustrates this terminology. The rest of the circuit might represent an audio amplifier and the small circles at the ends of the lines might represent the terminals to which you would normally connect a loudspeaker. The lines themselves represent conductors, indicating that the terminals are connected to points inside the circuit. The terms open and short are used with reference to the terminals alone, regardless of how or to what the associated conductors are connected inside the rest of the circuit. The current through an open circuit equals zero, regardless of the voltage across the open circuit, and the voltage across a short circuit equals zero, regardless of the current through the short circuit. If an element connecting two terminals is removed, it is said that the terminal pair
Example 3.2. In Fig. 3.9(a), elements 1 and 2 are not in series because of the intervening connection to element 3, which allows some of the current passing through element 1 to bypass element 2; however, element 1 is in series with the parallel connection of elements 2 and 3. In Fig. 3.9(b), elements 1 and 2 are not in parallel because of the intervening element 3; however, element 1 is in parallel with the series connection of elements 2 and 3.
+ i
i
i
1
v
2
+ v
1 −
Fig. 3.8 Elements in (a) series and (b) parallel
(a) series connection
2 −
(b) parallel connection
3 +
+ i3 3 i1
Fig. 3.9 See Example 3.2
1
+ v2 −
2 (a)
− 2
−
i2 1
v1
v3
(b)
54
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws 1 1
2
2
3
4
3
(a)
+
4
i
+
v
v
−
−
i
(b) (a)
(b)
Fig. 3.10 See Exercise 3.2 i +
+ rest of the circuit
(a) open circuit (the terminals are open)
v −
rest of the circuit
v =0 −
(b) short circuit (the terminals are shorted)
Fig. 3.11 Open and shorted terminals
is opened, or that the terminal pair is made an open circuit. If a conductor is connected between two terminals, it is said that the terminals are shorted, or that the terminal pair is made a short circuit. The terms open circuit and short circuit (or open and short) are most correctly used when neither is the normal condition; i.e., when the opened or shorted condition is temporary, whether intentional or accidental. For example, if you disconnect a loudspeaker from the output terminals of your home audio amplifier, you are opening those terminals. If you accidentally allow your screwdriver to contact both terminals at once, you have shorted the terminals. Nonetheless, both open and shorted are sometimes used to describe normal conditions; for example, a conductor might be called a short circuit, even if the conductor occupies its intended place in a circuit.
3.6 Basic Circuit Elements: Resistors and Independent Sources In this section, we define three two-terminal circuit elements: A resistor, an independent voltage source, and an independent current source.2 A number of useful circuits can be described using only these elements, and one or more of these elements appears in virtually every circuit model of practical importance.
Table 3.1 Symbols3 and terminal characteristics for three basic circuit elements Element Symbol Terminal characteristic resistor
+ v –
n ¼ iR
R
voltage source
+ v – i
n ¼ n0 ðindependent of iÞ
v0
current source
i
+ v –
i ¼ i0 ðindependent of nÞ i0
The terminal characteristic of a two-terminal circuit element is the relation the element establishes between the voltage across and current through its terminals. We may take the positive direction of current as either into the terminal called positive (in the direction of a voltage drop) as in Fig. 3.12(a) or out of the terminal called positive (in the direction of a voltage rise), as in Fig. 3.12(b), and we may take either current or voltage as the independent variable. That is, we may express the terminal characteristic of an element as either i ¼ f (v) or v ¼ f1(i), where the positive direction of current is either into or out of the positive terminal of the element. In general, we may use whichever of these four formulations is most convenient. Table 3.1 gives the names, graphic symbols, and terminal characteristics of the three elements defined in this section. The terminal characteristic of an element is independent of what is connected to the element. For example, the current through and voltage across a resistor are related by v ¼ i R, regardless of
3
2 The meaning of independent in this context is described in the sequel.
i
+ –
i =0
Fig. 3.12 Pertaining to the definition of the terminal characteristic of a two-terminal element
The polarity marks and arrows and the letters n and i (without subscripts) define the voltage and current that appear in the terminal characteristic. They are not part of the symbol for the element.
3.6 Basic Circuit Elements: Resistors and Independent Sources
55
i
i
i0
slope = R −1
v0
v
Fig. 3.13 Graphical representations of the terminal characteristics of the elements defined in Table 3.1
(a) resistor: i = v/R
(b) voltage source: v = v0 independent of i
what else is connected to the resistor and regardless of the nature of the current or voltage. Of course, this is an idealization. The terminal characteristic v ¼ i R describes a physical resistor only under certain operating conditions. For example, a resistor can be destroyed by a sufficiently large current, after which it is no longer described by v ¼ R i. Figure 3.13 shows graphical representations of the terminal characteristics of the elements defined in Table 3.1. The current i0 and voltage v0 can be timevarying, so you should regard Fig. 3.13(b) and (c) as snapshots (still photos), unless the current i0 and voltage v0 are constant. A label usually is written by the symbol for an element. For example, the label R is attached to the resistor in Table 3.1. The label serves double duty: It represents both the name and the resistance of the resistor. For example, when written next to the symbol for a resistor, R1 is the name of the resistor (distinguishes that resistor from others labeled R2, R3, ) and also stands for the resistance of the resistor. For example, we might say that resistor R1 has resistance R1 ¼ 1 kO. When writing equations describing circuits, it often is convenient to use conductance, rather than resistance. The conductance of a resistor having resistance R is denoted by G and is defined by G ¼ R1 :
(3.2)
Using conductance, Ohm’s law is written i ¼ G v:
i
(3.3)
We regard resistance as the fundamental quantity and conductance mainly as a convenient way to express reciprocals of resistances in circuit equations. Thus, in this book, a label or a numerical value appearing beside the symbol for a resistor always denotes resistance, not conductance, as illustrated by Fig. 3.14.
R
v
v
(c) current source: i = i0 independent of v
G –1
Fig. 3.14 Labeling a resistor using conductance
The voltage across a voltage source is called the source voltage (denoted by v0 in Table 3.1) and is independent of the current through the voltage source. In other words, the voltage across the voltage source shown in Table 3.1 equals v0, no matter what is connected to the source. The source voltage may be constant but in general varies with time. A conductor is equivalent to a voltage source whose source voltage equals zero. Conversely, a voltage source whose source voltage equals zero is equivalent to a conductor (a short circuit). Thus we say that the internal resistance of a voltage source equals zero. The current through a current source is called the source current (denoted by i0 in Table 3.1) and is independent of the voltage across the current source. In other words, the current through the current source in Table 3.1 equals i0, no matter what is connected to the source. The source current may be constant but in general varies with time. An open circuit is equivalent to a current source whose source current equals zero. Conversely, a current source whose source current equals zero is equivalent to an open circuit. Thus we say that the internal conductance of a current source equals zero (or that the internal resistance is infinite). Circuit elements cannot be connected in ways that are self-contradictory; i.e., in ways that cause conflicts among defined quantities. For example, the circuit in Fig. 3.15(a) is self-contradictory unless v1 ¼ v2, in which case one of the sources is superfluous. Similarly, the connection in Fig. 3.15(b) is self-contradictory unless i1 ¼ i2, in which case one of the sources is superfluous. Ideal voltage sources cannot be connected in parallel and Ideal current sources cannot be connected in series.
56
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws i1 + v – 1
+
i2
(a)
+ v1 –
(b)
Fig. 3.15 Self-contradictory connections
It follows from (3.1) that vab ¼ vx ¼ vac vbc ¼ v1 v2 ¼ 10 V
Exercise 3.3. Refer to Fig. 3.17. Find the voltages vab, vac, vbd Figure 3.18(a) shows an alternate symbol for a constant-voltage source alongside the conventional symbol in Fig. 3.18(b). The symbol in Fig. 3.18(a) was originally inspired by the architecture of a battery, in which metallic plates are separated by an electrolyte. In electronic circuits, the symbol in Fig. 3.18(a) is used primarily to denote a constant-voltage power supply; e.g., the battery in a cell phone.
Fig. 3.16 See Example 3.3 a
b
v1 + –
+ v – 2
d
c
+ –
vbc ¼ v2 :
+ –
v3
Fig. 3.17 See Exercise 3.3
v0
v0
(a)
+ –
vac ¼ v1 ;
v2
+
Example 3.3. In the circuit of Fig. 3.16, the source voltages are v1 ¼ 5 V and v2 ¼ 15 V. Find the voltage vx across the (unspecified) circuit element. Solution: We label three points, as shown in the figure, where, by the definition of an ideal voltage source,
b
c
–
Labels for current and voltage sources serve both as names for the sources and as symbols for the source current or voltage. For example, we might say that the source voltage for the source v0 is v0 ¼ 5 V, or that the source current for the current source i0 is i0 ¼ 25 mA. The sources defined in Table 3.1 are called independent sources, as in independent voltage source and independent current source, because the source voltage or source current depends only upon time (e.g., is independent of any other currents or voltages). In a subsequent chapter, we describe dependent sources, whose source voltages or source currents depend upon other quantities; e.g., currents or voltages in other branches of the circuit.
−
vx
a
+ v – 2
(b)
Fig. 3.18 Equivalent symbols for a constant-voltage source
The (ideal) sources defined above do not exist. For example, no physical voltage source, such as a battery, can maintain a constant voltage across its terminals regardless of the current through the terminals. Nonetheless, ideal sources either alone or in combination with other elements can be good models for physical sources. Because of the nature of known methods for generating electricity, most everyday physical sources (e.g., batteries, generators, solar cells, and fuel cells) behave more like voltage sources than current sources. However, electronic circuits approximating current sources can be constructed and are quite useful.
3.7 Kirchhoff’s Current Law and Node Analysis Kirchhoff’s current law4 states that the algebraic sum of the currents leaving any enclosed volume in a
4
After the German physicist Gustav Robert Kirchhoff (1824–1887).
3.7 Kirchhoff’s Current Law and Node Analysis
57 volume enclosing a node
node
i2
i1
i2
i1
i3
i3
Fig. 3.19 An illustration of Kirchhoff’s current law
(a)
(b)
i2
i2 i3 i1
i1 i4
Fig. 3.20 Another Illustration of Kirchhoff’s current law
(a)
circuit equals zero.5 We may express Kirchhoff’s current law as X
in ¼ 0:
(3.4)
n
where the in are currents leaving an enclosed volume and the sum is over all possible current paths entering or exiting the volume. In (3.4), currents entering the volume are negative. In applications of Kirchhoff’s current law to electric circuits, volumes of interest enclose connections joining two or more elements and conductors provide current paths into and out of the volume, as illustrated in Fig. 3.19(a), where i1 þ i2 þ i3 ¼ 0: In such cases, we may think of the currents as leaving the point at which the elements are connected, as illustrated in Fig. 3.19(b). A point at which two or
i3
i4 (b)
more elements are connected is called a node, and Kirchhoff’s current law often is stated as the algebraic sum of the currents leaving any node equals zero. In the algebraic sum of currents leaving a volume or node, currents entering the volume or node are negated.6 For example, in both Fig. 3.20(a) and (b), i1 þ i2 i3 þ i4 ¼ 0:
Exercise 3.4. Is the circuit in Fig. 3.21 selfconsistent? Use Kirchhoff’s current law to justify your answer Kirchhoff’s current law is derived from more fundamental principles in textbooks on electromagnetics. We shall accept Kirchhoff’s current law as an empirical law, noting that it amounts to requiring that current through any plane intersecting the path of the current be continuous; that is, the currents on each side of the plane are the same.7 From another point of view,
5
Kirchhoff’s current law can also be stated as “the sum of currents entering a volume equals zero” or as “the sum of the currents entering a volume equals the sum of the currents leaving the volume.” For the present, it is best to stick with one version of the law.
6
In “leaving” and “entering,” we are referring to the direction of the arrow associated with the current. 7 Here, “current” includes both conduction current and displacement current.
58
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws i1
a
i2 i2
i1 i0
R1
i3
i0
R2
i2
i1 R1
R2
b = ref
(a)
(b)
Fig. 3.21 See Exercise 3.4 Fig. 3.23 See Example 3.5 i2 i1 i3 i4
Fig. 3.22 See Example 3.4
charge is not manufactured at a node, nor does charge accumulate at a node, so (because charge is conserved) the net charge leaving a node or volume must be zero. Example 3.4. In Fig. 3.22, i1 ¼ 5 A, i2 ¼ 1 A, i3 ¼ 2 A. Find the current i4. Solution: Kirchhoff’s current law gives
• Solve the resulting equations for the node voltages. • Use the node voltages and Ohm’s law to find any currents of interest. Example 3.5. Obtain expressions for the currents i1, i2 in the circuit of Fig. 3.23(a). Solution: We identify and label the nodes in the circuit as shown in Fig. 3.23(b), choosing node b as the reference node. The only other node in the circuit is node a, and the (unknown) voltage at that node relative to the reference is denoted in single-subscript notation by va. The net current leaving node a must be zero, so by Kirchhoff’s current law,
ði1 Þ þ i2 þ i3 þ i4 ¼ 0; It follows that
i0 þ i1 þ i2 ¼ 0 ) i1 þ i2 ¼ i0 : By Ohm’s law,
i4 ¼ i1 i2 i3 ¼ 5 1 2 ¼ 2A
Applying Kirchhoff’s current law to circuit analysis leads to what is called node analysis (or nodal analysis), in which node voltages are taken as the unknown quantities. If one or more currents are the quantities of ultimate interest, they may be expressed via Ohm’s law in terms of the voltages and resistances. Node analysis proceeds as follows: • Identify and label a reference node for other voltages in the circuit. • Identify and label each other node for which the voltage at that node, relative to the reference node, is unknown. • Write Kirchhoff’s current law at each such node, using Ohm’s law to express the currents in terms of the node voltage and the resistance of the resistors attached to the node.
i1 ¼
va ; R1
i2 ¼
va ; R2
and Kirchhoff’s current law is expressed in terms of the unknown node voltage va by va va 1 1 R1 R2 ¼ i0 ) va ¼ þ ¼ va þ i0 : R1 R2 R1 þ R2 R 1 R2 Thus i1 ¼
va R2 ¼ i0 ; R1 R1 þ R2
i2 ¼
va R1 ¼ i0 R2 R1 þ R2
The circuit in Fig. 3.23 is called a current divider because the current provided by the source is divided between the two resistors in the manner specified by the relations above.
3.7 Kirchhoff’s Current Law and Node Analysis
59
which yields
Exercise 3.5. Refer to Fig. 3.24. Obtain expressions for the currents through the three resistors.
v 2 ¼ vb ¼
R2 v0 R1 þ R2
The circuit of Fig. 3.25 is called a voltage divider because the voltage provided by the source is divided between the two resistors in agreement with the relation above
Example 3.6. Obtain an expression for the voltage v2 across the resistor R2 in the circuit of Fig. 3.25(a). Solution: We identify and label the nodes and choose a reference node as shown in Fig. 3.25 (b). By the definition of an independent voltage source, va ¼ v0. Thus the only unknown node voltage is vb ¼ v2. By Kirchhoff’s current law and Ohm’s law,
Exercise 3.6. Refer to Fig. 3.25. Express the voltage vab across the resistor R1 in terms of R1, R2, and v0
vba vb vb va vb þ ¼ þ R1 R2 R1 R2 vb v0 vb ¼ þ ¼ 0; R1 R2
i1 þ i2 ¼
I0
R1
R2
Example 3.7. Obtain an expression for the current i2 in the circuit of Fig. 3.26(a). The resistances and the source voltages are presumed to be known. Solution: We identify and label the nodes in the circuit as shown in Fig. 3.26(b), choosing node d as the reference node. By the definition of an ideal voltage source,
R3
Fig. 3.24 See Exercise 3.5
va ¼ v1 ; vc ¼ v2 ; i1
a R1 + v – 0
+ R2
v2
i2
R1 + v – 0
+ R2
–
(a)
so vb is the only unknown node voltage. We apply Kirchhoff’s current law at node b and obtain
b
v2
vb va vb vb vc þ þ R1 R2 R3 vb v1 vb vb v2 ¼ þ þ ¼ 0; R1 R2 R3
i1 þ i2 þ i3 ¼
–
(b)
Fig. 3.25 See Example 3.6
R5 R1
R5 R3
R1
a
i1
i2 + v1 –
Fig. 3.26 See Example 3.7
R2
(a)
i3
b
R3 c
i2 v2 + –
+ v1 –
R2 d = ref (b)
v2 + –
60
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws
To simplify the notation, we use conductances in place of resistances; e.g., G1 ¼ 1/R1. Thus
in which the only unknown is vb. We find 1 1 1 1 v1 v2 : vb ¼ þ þ þ R1 R2 R1 R2 R3
2 1 vc v0 vb þ ¼ R1 R1 R1 R2
Finally, by Ohm’s law vb R v1 v2 ¼ þ i2 ¼ ; R2 R2 R1 R2 1 1 1 1 þ þ R¼ R1 R2 R3
) ð2G1 þ G2 Þvb G1 vc ¼ G1 v0 ; vb 1 1 1 v0 þ þ þ vc ¼ R1 R3 R1 R2 R3 ) G1 vb þ ðG1 þ G2 þ G3 Þvc ¼ G3 v0 : To simplify further, let
Exercise 3.7. Refer to Fig. 3.26. Obtain expressions for the currents i1, i3
2 1 þ ffi 2:455 mS; R1 R2 1 1 1 þ þ ffi 1:555 mS: Gc ¼ R1 R2 R3
Gb ¼
Example 3.8. Express the voltages v1, v2 in the circuit of Fig. 3.27(a) in terms of the source voltage v0, where R1 ¼ 1 kO, R2 ¼ 2.2 kO, and R3 ¼ 10 kO. Solution: We identify and label the nodes as shown in Fig. 3.27(b), choosing node d as the reference node. By the definition of an ideal voltage source, va ¼ v0. The node voltages vb ¼ vbd and vc ¼ vcd are unknown, so we apply Kirchhoff’s current law to those nodes. Thus
whence Gb vb G1 vc ¼ G1 v0 ; G1 vb þ Gc vc ¼ G3 v0 ; which yield
vb v0 vb vb vc þ þ ¼0 R R2 R1 1 2 1 vc v0 vb ¼ ; þ ) R1 R1 R 1 R2 vc vb vc vc v0 i3 þ i4 þ i5 ¼ þ þ ¼0 R1 R2 R3 vb 1 1 1 v0 þ þ vc ¼ : ) þ R1 R3 R1 R2 R3 i1 þ i2 þ i3 ¼
v b ¼ v1 ¼
G 1 ð G c þ G3 Þ v0 ffi 0:588v0 ; Gb Gc G 1 2
v c ¼ v2 ¼
Gb G3 þ G1 2 v0 ffi 0:442v0 : Gb Gc G 1 2
Exercise 3.8. Refer to Fig. 3.27. Express the voltages vac, vbc in terms of the source voltage v0.
R3 R1 + v0 –
Fig. 3.27 See Example 3.8
R3 R1
R2
(a)
+ v1 –
R1
a R2
+ v2 –
i1
b i3
R1 −i3
i2 + v – 0
R2 d = ref (b)
R2
i5 c i4
3.7 Kirchhoff’s Current Law and Node Analysis
61
The next example illustrates application of Kirchhoff’s current law to a circuit in which two nodes, neither of which is the reference node, are connected by an independent voltage source. Each independent voltage source that appears in a circuit reduces the number of unknown node voltages by one. Example 3.9. Refer to Fig. 3.28(a). Express the voltage v2 in terms of the circuit parameters. Solution: We choose the reference node and label the remaining nodes, as shown in Fig. 3.28(b), and denote the current through the source v0 by ix. By the definition of an ideal voltage source, v c ¼ v1 ; v 2 ¼ vb ¼ v a þ v 0 : If va were known, the voltage vb would be determined. Writing Kirchhoff’s current law at nodes a and b gives
Thus, v2 ¼ vb ¼ va þ v0 R1 ½R2 R3 i0 þ R2 v1 ðR2 þ R3 Þ v0 ¼ þ v0 R1 R2 þ R1 R3 þ R2 R3 R2 ðR1 R3 i0 þ R1 v1 þ R3 v0 Þ ¼ : R1 R2 þ R1 R3 þ R2 R3 Once you have solved two or three problems such as Example 3.9, where two non-reference nodes are connected by an independent voltage source, you will realize that it is unnecessary to introduce an extra unknown, such as ix. You can simply look ahead and express the current passing through the source in terms of the dependent node voltage at the other end of the source (node b, in Example 3.9). Example 3.10. Refer to Fig. 3.29(a). Express the voltage v0 in terms of the circuit parameters. Solution: We choose the reference node and label the remaining nodes, as shown in Fig. 3.30(b). By the definition of an ideal voltage source, vc ¼ vb þ v1 ; vd ¼ vc þ v2 ¼ vb þ v1 þ v2 : Applying Kirchhoff’s current law to node a gives
va v b v1 v b þ ; i0 þ þ ix ¼ 0; ix þ R1 R3 R2 which yield va þ v0 v1 va þ v0 va þ ¼ i0 R3 R2 R1 R1 ½R2 R3 i0 þ R2 v1 ðR2 þ R3 Þ v0 ) va ¼ : R1 R2 þ R1 R3 þ R2 R3
i1 þ
v0
R3 + v2 −
R1
v0
a ix + v – 1
R2
i0
+ –
i0
va va vb þ ¼ 0: R1 R2
R2
a
R3 R4
i1
b R1
R2
(a)
v1
c
v2
R3 R4
–
Fig. 3.29 See Example 3.10
v1
+ –
R1
R2
+ –
i1
v2 + –
+ –
v0
c
(b)
v1 +
R3
ix b
R1
(a)
Fig. 3.28 See Example 3.9
(3.5)
(b)
d
62
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws v1
a
b
+ –
Exercise 3.11. Refer to Fig. 3.30. Obtain an expression for the voltage vbc.
i1
R1
R2
R3
i2
c
Fig. 3.30 See Exercise 3.11
3.8 Kirchhoff’s Voltage Law and Mesh Analysis
The current leaving node b through the source v1 equals vc /R3 þ vd /R4. Applying Kirchhoff’s current law to node b gives v b va v b þ v 1 v b þ v 1 þ v 2 þ þ ¼ 0: R2 R3 R4
(3.6)
Kirchhoff’s voltage law states that the algebraic sum of the voltage drops8around any closed path equals zero. In the algebraic sum of voltage drops around a closed path, voltage rises are negated. With reference to Fig. 3.31, Kirchhoff’s voltage law around the dotted path can be expressed as X
Using conductance notation and collecting terms in (3.5) and (3.6) gives ðG1 þ G2 Þva G2 vb ¼ i1 ; G2 va þ ðG2 þ G3 þ G4 Þvb ¼ ðG3 þ G4 Þv1 G4 v2 :
(3.7)
Eliminating vb yields v a ¼ v0 ¼
ðG2 þ G3 þ G4 Þi1 G2 ½ðG3 þ G4 Þv1 þ G4 v2 : ðG2 þ G3 þ G4 ÞðG1 þ G2 Þ G22
vn ¼ 0:
(3.8)
n
Kirchhoff’s voltage law follows from the definitions of electric potential and voltage. The electric potential at any particular point and time has a single, specific value, which does not depend upon how we arrive at the point. Thus, if we imagine that we instantaneously follow a closed path that begins and ends at the same point (a) but is otherwise arbitrary, the potential at the end of the path is the same as that at the beginning; that is, the net potential difference (voltage drop) around the closed path is FðaÞ FðaÞ ¼ 0:
Exercise 3.9. Refer to Fig. 3.29(b) in Example 3.10 above. Choose nodes a and d as the independent nodes and write node equations at those nodes. The voltages va and vd must be the only unknown quantities that appear in the equations.
Kirchhoff’s voltage law follows, because the point can be any point and the path can be any path through the point. Example 3.11. In Fig. 3.32, v1 ¼ 3 V, v2 ¼ 10 V, v4 ¼ 15 V Find the voltage v3. Solution: Kirchhoff’s voltage law gives v1 þ v2 þ v3 v4 ¼ 0:
Exercise 3.10. Refer to Fig. 3.29(b) in Example 3.10 above. Choose nodes b and c as the independent nodes and write node equations at those nodes. The voltages vb and vc must be the only unknown quantities that appear in the equations.
8
Kirchhoff’s voltage law can also be stated as “the sum of voltage rises around any closed path equals zero” or as “the sum of the rises equals the sum of the drops.” Again, for the present, it is best to stick with one version of the law.
3.8 Kirchhoff’s Voltage Law and Mesh Analysis
+ v1
+
–
v2
63
–
–
+
v5
v3
+
– v4
law to each mesh in a circuit and solving for the mesh currents is called mesh analysis. In mesh analysis, we regard each mesh as the path taken by a hypothetical current, called a mesh current. If one or more voltages are the quantities of ultimate interest, they may be expressed via Ohm’s law in terms of the currents and resistances. Mesh analysis proceeds as follows:
–
+
Fig. 3.31 Illustration of Kirchhoff’s Voltage Law – see (3.8)
+ v1
–
+
+ v2
v4 –
• Identify each mesh and associate a mesh current with each. • Write Kirchhoff’s voltage law around each mesh, using Ohm’s law to express the voltages across resistors in the mesh in terms of the mesh current and the resistances of the resistors. • Solve the resulting equations for the mesh currents. • Use the mesh currents and Ohm’s law to find any voltages of interest.
–
– v3 +
Fig. 3.32 See Example 3.11
A few examples should clarify the procedure. + – + – v1
v2
v3 + –
Fig. 3.33 See Exercise 3.12
where v4 is negated because it is a voltage rise (in the direction of the path). Solving for v3 gives
Example 3.12. (Compare with Example 3.6): Obtain an expression for the voltage across the resistor R2 in the circuit of Fig. 3.35. The resistances and source voltage are presumed to be known. Solution: There is only one mesh. We define a path and associated mesh current, as shown in Fig. 3.35. We write Kirchhoff’s voltage law clockwise around the path and obtain
v3 ¼ v4 v1 v2 ¼ 15 3 10 ¼ 2 V:
Exercise 3.12. Is the circuit in Fig. 3.33 selfconsistent? Use Kirchhoff’s voltage law to justify your answer. A loop is a closed path in or around a circuit. All of the dashed lines in Fig. 3.34 are loops. A mesh is a loop that does not enclose (encircle) any other loops. Paths 1, 2, 3 are meshes. Paths b and c are not meshes. Path b encloses two meshes. Path c encloses three. Kirchhoff’s voltage law can be applied to any loop or mesh, but in the beginning, it is best to use only meshes, as that is the surer way to obtain the required number of independent equations. Applying Kirchhoff’s voltage
1
3
2 b c
Fig. 3.34 Illustrating the definitions of mesh and loop
64
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws R1 +
v1
R1
+ v1 –
– i
v0 + –
+ v2
R2
i1
va + –
+ v3
i2
R3
i + v – b
Fig. 3.36 See Example 3.13
Fig. 3.35 See Example 3.12
v0 þ v1 þ v2 ¼ 0; where, by Ohm’s law v2 ¼ R2 i;
so Kirchhoff’s voltage law may be written R1 i þ R 2 i ¼ v 0 ; which yields i¼
+ v2 –
–
–
v1 ¼ R1 i;
R2
v0 : R1 þ R2
where i1–i2 is the total current down through the resistor R3. Using these relations in the Kirchhoffvoltage-law equations above gives two equations in the two unknown currents i1, i2: R1 i1 þR3 ði1 i2 Þ ¼ va ) ðR1 þR3 Þi1 R3 i2 ¼ va ; R2 i2 R3 ði1 i2 Þ ¼ vb ) R3 i1 þ ðR2 þR3 Þi2 ¼ vb : To eliminate i1, we add R3 times the first equation to (R1 þ R3) times the second. This gives R3 2 i2 þ ðR1 þ R3 ÞðR2 þ R3 Þ i2 ¼ R3 va ðR1 þ R3 Þ vb ;
By Ohm’s law v2 ¼ R2 i ¼
R2 v0 : R 1 þ R2
which yields i ¼ i2 ¼
Example 3.13. Obtain an expression for the current i in the circuit of Fig. 3.36. The resistances and source voltages are presumed to be known. Solution: There are two meshes and associated mesh currents, as shown in Fig. 3.36, noting that the current of interest is i ¼ i2. We write Kirchhoff’s voltage law around each path to obtain v1 þ v3 va ¼ 0; v2 þ vb v3 ¼ 0: By Ohm’s law v1 ¼ R1 i1 ; v2 ¼ R2 i2 ; v3 ¼ R3 ði1 i2 Þ;
R3 va ðR1 þ R3 Þ vb : R1 R2 þ R1 R3 þ R2 R3
Exercise 3.13. Obtain an expression for the current i1 in Fig. 3.36. The next example illustrates application of Kirchhoff’s voltage law to a circuit containing a current source. Each independent current source in a circuit reduces the number of unknown mesh currents by one. Example 3.14. Obtain an expression for the current i1 through the resistor R1 in the circuit of Fig. 3.37.
3.8 Kirchhoff’s Voltage Law and Mesh Analysis
65
Solution: Although there are two meshes, there is only one unknown current, because, by Kirchhoff’s current law and the definition of an independent current source, the current through the resistor R2 is
is never necessary to choose a path that passes through an independent current source because, by definition, the current through an independent current source is known. Example 3.15. Refer to Fig. 3.38. Use mesh analysis to obtain an expression for the voltages v1, v2, v3. Solution: There are four meshes, as shown in Fig. 3.38, but two of the mesh currents (i0 and 3i0) are known. Thus we need only the two equations for the unknown mesh currents i1, i2.
i2 ¼ i1 þ i0 ; and i0 is known. Thus we need only one equation. Writing Kirchhoff’s voltage law clockwise around the indicated path gives va þ v1 þ v2 þ vb ¼ 0:
R1 i0 þ ðR1 þ R2 þ R3 Þi1 R3 i2 ¼ 0; 3R4 i0 R3 i1 þ ðR3 þ R4 þ R5 Þi2 ¼ 0:
By Ohm’s law,
To simplify notation, let
v1 ¼ R1 i1 ; v2 ¼ R2 i2 ¼ R2 ði1 þ i0 Þ:
RA ¼ R1 þ R2 þ R3 ; RB ¼ R3 þ R4 þ R5 : Thus Kirchhoff’s voltage law yields Then va þ R1 i1 þ R2 ði1 þ i0 Þ þ vb va vb R2 i0 ¼ 0 ) i1 ¼ : R 1 þ R2
R A i1 R 3 i2 ¼ R 1 i 0 ;
R3 i1 þ RB i2 ¼ 3R4 i0 ;
which yield i1 ¼
When applying Kirchhoff’s voltage law to a circuit containing one or more independent current sources, it
R1 RB þ 3R3 R4 R1 R3 þ 3RA R4 i0 ; i2 ¼ i0 ; RA RB R3 2 RA RB R3 2
and thus i1
R1
R2
i2
+ v1 – va + –
+ v2
R R R3 2 RB R1 3R4 R3 v1 ¼ ði0 i1 ÞR1 ¼ A B R1 i 0 ; RA RB R3 2 R R þ3R3 R4 R1 R3 3RA R4 v2 ¼ ði1 i2 ÞR3 ¼ B 1 R 3 i0 ; RA RB R3 2 R R þ3RA R4 v 3 ¼ i2 R 5 ¼ 1 3 R5 i0 : RA RB R3 2
– + v – b
i0
Fig. 3.37 See Example 3.14 3i0
3i0 R2
v1 i0 i0
Fig. 3.38 See Example 3.15
R1
i1
v2
R3
R4
i2
v3
R5
66
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws i0 R1 v0 + –
+ v – 0
R3 R2
R2
v2 –
R4
i1
+
R1
5i0
Fig. 3.40 Voltage divider
i2
R1
Fig. 3.39 See Exercise 3.14
v0
Exercise 3.14. Refer to Fig. 3.39. Obtain expressions for the currents i1, i2.
i1 + va
+ –
i3 i2 = i1−i3 R2
R3
– ref
Fig. 3.41 Circuit used to illustrate erroneous application of voltage division. See text
3.9 Voltage and Current Dividers Figure 3.40 shows the simplest form of a voltage divider, so named because the source voltage v0 is divided between the resistors R1, R2. The voltage across the resistor R2 is given by (see Example 3.6) v2 ¼
R2 v0 : R1 þ R2
(3.9)
Equation (3.9) applies only if all of the current that passes through the resistor R1 also passes through the resistor R2. A common error is applying (3.9) to a circuit such as the one shown in Fig. 3.41, where some of the current passing through R1 is diverted to a load R3 (not all passes through R2). In Fig. 3.41, the voltage va is not given by (3.9), unless the resistance R3 is so much larger than R2 that the current i3 through R3 is a negligible fraction of i1. For a specific example, consider the circuit of Fig. 3.42(a), in which the load on the voltage divider is expressed as a multiple of the resistance R. The voltage v2 is given by v2 ¼
k v0 ; v0 ¼ 2 þ k1 2k þ 1
(3.10)
as you are asked to show in Exercise 3.15. The load voltage v2 is approximately half the source voltage if k is sufficiently large, as shown by the graph in Fig. 3.42 (b). For example, for k ¼ 100, v ¼ 0.498v0.
Exercise 3.15. Show that the voltage v2 in Fig. 3.42(a) is given by (3.10). Figure 3.43 shows the simplest form of a current divider, so named because the source current is divided between the resistors R1, R2. The current through the resistor R2 is given by (see Example 3.5) i2 ¼
R1 i0 : R1 þ R2
(3.11)
Voltage and current dividers are quite common, and you should memorize the circuits in Figs. 3.40 and 3.43 and the associated relations (3.9) and (3.11). Voltage and current dividers can contain more than two resistors (can divide voltages or currents into more than two parts), but two-part dividers are by far the most common.
3.10 Superposition As it applies to resistive circuits, the principle of superposition can be stated as follows: Suppose a circuit contains two or more independent current or voltage sources. Any particular current or voltage in the circuit can be obtained as the sum of the corresponding currents or voltages found by applying the sources one at a time, all others being set to zero.
3.10 Superposition
67 0.5 0.45 v2 v0
R
0.4
+ v0
R
kR
v2
0.35
– 0.3 1
Fig. 3.42 The voltage v2 is approximately half the source voltage for large k
10
100
1.103
k (a)
(b)
i2
i0
R1
R2
circuit), as illustrated by Fig. 3.44(c). We obtain ijv0 ¼0 ¼
Fig. 3.43 Current divider
Note that setting a source voltage to zero is equivalent to replacing the associated source with a short circuit and setting a source current to zero is equivalent to replacing the associated source with an open circuit.9 Example 3.16. Using superposition, obtain an expression for the current ix in the circuit shown in Fig. 3.44(a). Solution: We first find the current i due to the voltage source v0 acting alone; that is, with the source current i0 set to zero (replaced by an open circuit), as illustrated by Fig. 3.44(b). This gives iji0 ¼0 ¼
v0 : R1 þ R2 þ R3
Next we find the current i due to the current source i0 acting alone; that is, with the source voltage v0 set to zero (replaced by a short
9
Review the definitions of independent current and voltage sources in Section 3.6.
R2 i0 : R1 þ R2 þ R3
There are no other sources, so the (total) current ix is given by v0 þ R 2 i 0 : i ¼ iji0 ¼0 þ ijv0 ¼0 ¼ R1 þ R2 þ R3
In applications of superposition, the various sources may be applied in any order. The principle of superposition is a consequence of Kirchhoff’s laws and the fact that the terminal characteristic of a resistor is linear. We can show this as follows: Applying either or both of Kirchhoff’s laws to a resistive circuit leads to a set of equations of the form a11 x1 þ a12 x2 þ þ a1N xN ¼ b11 y1 þ b12 y2 þ þ b1M yM ; a21 x1 þ a22 x2 þ þ a2N xN ¼ b21 y1 þ b22 y2 þ þ b2M yM ; .. . aN1 x1 þ aN2 x2 þ þ aNN xN ¼ bN1 y1 þ bN2 y2 þ þ bNM yM ;
(3.12)
where the y’s are known source currents or voltages, the x’s are unknown currents or voltages, and the a’s and b’s are (in general) functions of circuit parameters (resistances and conductances) and are independent of the known and unknown currents and voltages. The solution of such a set of equations has the form
68
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws i0 R1
i0
R2
+ – v0
R1
R3
R2
+ v – 0
i i =0 0
i
Fig. 3.44 See Example 3.16
(a)
x1 ¼ c11 y1 þ c12 y2 þ þ c1M yM ; x2 ¼ c21 y1 þ c22 y2 þ þ c2M yM ; .. .
(b)
(3.13)
xN ¼ cN1 y1 þ cN2 y2 þ þ cNM yM ; where the c’s are functions of the circuit parameters (the a’s and b’s) but do not depend upon the source currents and voltages (the y’s). For example, in Example 3.13 we obtain the equation ðR1 þ R3 Þ i1 R3 i2 ¼ va ; R3 i1 þ ðR2 þ R3 Þ i2 ¼ vb ; which have the form given in (3.12), with N ¼ 2; x1 ¼ i1 ; x2 ¼ i2 ; a11 ¼ R1 þ R3 ; a12 ¼ R3 ; a21 ¼ R3 ; a22 ¼ R2 þ R3 ; M ¼ 2; y1 ¼ va ; y2 ¼ vb ; b11 ¼ 1; b12 ¼ 0; b21 ¼ 0; b22 ¼ 1: The solution (see Example 3.13 and Exercise 3.13) is ðR2 þ R3 Þva R3 vb ðR2 þ R3 Þ va ¼ R1 R2 þ R1 R3 þ R2 R3 R1 R2 þ R1 R3 þ R2 R3 R3 vb ; þ R1 R2 þ R1 R3 þ R2 R3 R3 va ðR1 þ R3 Þvb R3 ¼ i2 ¼ va R1 R2 þ R1 R3 þ R2 R3 R1 R2 þ R1 R3 þ R2 R3 ð R1 þ R 3 Þ vb : þ R1 R2 þ R1 R3 þ R2 R3 (3.14) i1 ¼
which has the form given in (3.13), with
R1
R3
R2
i v =0 0
R3
(c)
c11 ¼
ðR2 þR3 Þ R3 ; c12 ¼ ; R1 R2 þR1 R3 þR2 R3 R1 R2 þR1 R3 þR2 R3
c21 ¼
R3 ðR1 þR3 Þ ; c22 ¼ : R1 R2 þR1 R3 þR2 R3 R1 R2 þR1 R3 þR2 R3
Equations obtained by applying Kirchhoff’s laws to any resistive circuit can be put in the form (3.12) and the solution for such a set can always be written in the form (3.13). Equation (3.13) (or, e.g., (3.14)) expresses each current and voltage in a resistive circuit as a linear combination of source currents and voltages. To find a particular current or voltage due to a particular source current or voltage, we set all source currents and voltages except the one of interest to zero. For example, with reference to (3.14), suppose we wish to obtain an expression for that part of the current i2 that can be attributed to the source vb. To do so, we set va ¼ 0 in the expression for i2. This gives i2 jva ¼0 ¼
ðR1 þ R3 Þ vb : R1 R2 þ R1 R3 þ R2 R3
(3.15)
Similarly, if we wish to obtain an expression for that part of the current i2 that can be attributed to the source va, we set vb ¼ 0 in the expression for i2. This gives
i2 jvb ¼0
R3 ¼ va : R1 R2 þ R1 R3 þ R2 R3
(3.16)
An expression for the (total) current i2, i.e., the second of Equations (3.14), can be obtained by adding the right sides of (3.15) and (3.16), in agreement with the principle of superposition. An important by-product of the proof of superposition given above is the following: If a linear resistive circuit contains exactly one independent source, then
3.11 Problems
69
every current and voltage in the circuit is proportional to the source current or voltage. This conclusion is reached by setting all but one source equal to zero in (3.13). Superposition can be generalized to more complex linear circuits, as shown in a subsequent chapter, and is one of the most important principles in circuit analysis. Although it usually does not greatly simplify analysis of resistive circuits excited by simple (e.g., constant or sinusoidal) sources, it is of tremendous importance in analysis of more general linear circuits subjected to more complex excitations. But superposition is most easily understood and applied in the context of resistive circuits and simple excitations, and mastering the concept in that setting will pay dividends in more realistic and practical applications.
3.11 Problems
Section 3.1 is prerequisite for the following problems. P 3.1 Under what conditions does an ideal conductor accurately model a physical conductor in a circuit diagram? How else might you model a physical conductor? P 3.2 Refer to Fig. P 3.1. Express the potentials at points e, f, g, h in terms of the potentials at points a, b, c, d. P 3.3 Figure P 3.2 shows a circuit diagram and an associated table of potentials. Complete the table. P 3.4 Figure P 3.3 shows a circuit diagram and an associated table of potentials. Complete the table. a
b
c
d
e
h f
g
Fig. P 3.1 See Problem P 3.2
Section 3.2 is prerequisite for the following problems. P 3.5 In Problem P 3.2, g is the reference node and va ¼ 15 V, vb ¼ 10 V, vc ¼ 10 V, vd ¼ 12 V. (a) Find ve, vf, vbh, vdh, vfh, vca. (b) Label the diagram with the voltage across each element using plus–minus notation. P 3.6 Refer to Problem P 3.3. (a) Take point i as reference and find the voltages vab, vbg, vcf, vcd, vfe, va, vb, vc, vf, vh. (b) Label the diagram with the voltage across each element using plus–minus notation. P 3.7 Refer to Problem P 3.4. (a) Take point k as reference and find the voltages va, vd, vh, vg, vbd, vdg, vih, vbf. (b) Label the diagram with the voltage across each element using plus–minus notation. P 3.8 In a certain circuit, the potentials at points a, b, c, and d are F(a) ¼ 50 V, F(b) ¼ 25 V, F(c) ¼ 15 V, and F(d) ¼ 100 V. Take point d as the reference and find the voltages va, vb, vc, vab, vbc, vac. P 3.9 In a certain circuit, the potentials at points a, b, c, and d are F(a) ¼ 5 V, F(b) ¼ 15 V, F(c) ¼ 25 V, and F(d) ¼ 10 V. Take point d as the reference and find the voltages va, vb, vc, vab, vbc, vac.
Section 3.3 is prerequisite for the following problems. P 3.10 Use the terms series and parallel to describe (in words) the connections shown in Fig. P 3.4. (Note: It is possible that neither of the terms apply to a particular arrangement.) P 3.11 Draw diagrams (e.g., see Fig. P 3.4) depicting the connections described below: (a) The parallel connection of elements 1 and 2 is in series with the parallel connection of elements 3 and 4. (b) Elements 1, 2 and 3 are in parallel with the series connection of elements 4 and 5. (c) Elements 1, 2, and 3 are in series with the parallel connection of elements 4 and 5.
Section 3.4 is prerequisite for the following problems.
70
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws h a
b
g
f
i e c d
point a b c d e f g h i
potential (V) 10 6
point a b c d e f g
potential (V) 2
h i j k l
3 6
4 1
Fig. P 3.2 See Problem P 3.3
d
a
i h
c b
e
f
l
j
k
Fig. P 3.3 See Problem P 3.4
2
1 1
5
4
3
3 (a)
1
4
(c) 4
3
10
g
2
2
5
1 5
2
3 4
Fig. P 3.4 See Problem P 3.10
(b)
P 3.12 What resistance is equivalent to (a) a short circuit and (b) an open circuit? P 3.13 What conductance is equivalent to (a) a short circuit and (b) an open circuit?
(d)
P 3.14 A switch can be idealized as a short circuit in the on position and as an open circuit in the off position. Suppose a battery, switch, and lamp are connected as shown in Fig. P 3.5. If the terminal
3.11 Problems
71
voltage of the battery is v0 and the resistance of the lamp is R, what are the voltage across and current through the lamp when the switch is in (a) the off position and (b) the on position?
P 3.15 For each circuit shown in Fig. P 3.6, express the voltages vab, vac, vad, vae in terms of the source voltages. P 3.16 Refer to Fig. P 3.7. Employ the definitions and techniques described in Sections 3.1 through 3.6 to express each labeled voltage and current (e.g., vx, ix) in terms of the resistances and source currents and voltages. P 3.17 There is something wrong (self-contradictory) with each circuit in Fig. P 3.8 where the source currents and voltages are arbitrary. What is it?
off
switch
Section 3.5 is prerequisite for the following problems.
on
lamp
battery
Fig. P 3.5 See Problem P 3.14
b
a
v1 + –
–
v0
+ –
+ –
d
c v1 + –
v0 +
v2
b
c
a v2 +
v0 + –
e
–
(a) v3
b
+ –
+ –
a
e
e v3
–
c v0
–
d
Fig. P 3.6 See Problem P 3.15
(c)
ix
ix
+
+ v0
+ –
R0
i0
vx
R0
v0
vx
+ –
v1 + –
+
ix (d)
R0
+ –
(c) R0
ix
R0
–
v1
(b)
+ –
vx
–
(a)
v0
ix
+
–
Fig. P 3.7 See Problem P 3.16
(b) v1 +
+ –
v2 +
d
+ –
v0
vx
R0 +
vx
–
i0
+
vy
–
vx –
i0
–
ix
+
R1
v0
+ vy –
(e)
(f)
+ –
72
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws
+ –
+ –
+ –
+ –
+ –
+ –
+ – + –
+ –
+ –
(a)
(c) (b)
(e)
Fig. P 3.8 See Problem P 3.17
(f)
(d)
+
Section 3.6 is prerequisite for the following problems. Note: In subsequent problems, the symbols in Fig. P 3.9 denote a voltmeter (V) having infinite resistance and an ammeter (A) having zero resistance. The polarity marks indicate the voltage polarity that gives a positive voltmeter reading and the arrow indicates the current direction that gives a positive ammeter reading. P 3.18 Refer to Fig. P 3.10, where VS ¼ 13 V. Ammeter 1 reads 5.04 mA, ammeter 2 reads 1.42 mA, and the voltmeter reads 7.96 V. Find the resistances RS, R1, R2. What are the nearest standard values for R1 and R2 from the lowest possible E series? P 3.19 Refer to Fig. P 3.11, where V0 ¼ 12 V. Ammeter 1 reads 2.14 mA, ammeter 2 reads 4.87 mA, and the voltmeter reads 5.46 V. Find the resistances R0, R1, R2. What are the nearest standard values for R0, R1, and R2 from the lowest possible E series? P 3.20 Find the current ix in the circuit of Fig. P 3.12, where i1 ¼ 5 mA, i2 ¼ 10 mA, and v0 ¼ 5 V. To what extent does the current ix depend upon the voltage v0? P 3.21 In the circuit of Fig. P 3.13, v0 ¼ 15 V, vad ¼ 10 V, vbd ¼ 5 V, and R ¼ 1 kO. Find the indicated currents and the voltages vab, vbc, vac. P 3.22 In the circuit of Fig. P 3.14, IS ¼ 100 mA and RS ¼ 10 kO. It is required that the current through R1 equal 25 mA and the current through R2 equal 50 mA. Find the resistances R1, R2. Then specify the nearest
– A
V
Fig. P 3.9 Symbols for voltmeter and ammeter + RS
V
1 A R2
+ – VS
R1 A 2
Fig. P 3.10 See Problem P 3.18 1 A R1 R2
+ –
R0 A
V V0
2
Fig. P 3.11 See Problem P 3.19 ix
i1
Fig. P 3.12 See Problem P 3.20
i2
+ – v0
–
3.11 Problems
73 v0 –
i1
Circuit
2R
a
i3 b i5
i2
i4
5R
3R
Fig. P 3.13 See Problem P 3.21
IS
RS
+
4R
c i6 2R
Circuit
d
R1
R2
R1
real voltmeter
R2
Rv
+ –
+
Fig. P 3.14 See Problem P 3.22
V –
iS
Fig. P 3.16 See Problem P 3.25
(1– k) R
vL
+ v – S kR
R1
RL iL
+ V0
–
R2
RL
+ vL –
Fig. P 3.15 See Problem P 3.23 Fig. P 3.17 See Problem P 3.26
values from the E192 series and obtain an expression for the percent error in each current. (Assume the values given for IS, RS are exact.) P 3.23 In Fig. P 3.15, the resistor on the left is a variable resistor, called a rheostat. The resistance from the movable tap (the arrow) to one end of the rheostat is kR and the total resistance of the rheostat is R. The voltage vL across the load resistor RL must equal onehalf of the source voltage vS. Express the required rheostat setting k in terms of the resistances R, RL. P 3.24 Refer to Problem P 3.23 and Fig. P 3.15. The current iL through the load resistor RL must equal onethird of the current iS. Express the required rheostat setting k in terms of the resistances R, RL. P 3.25 An ideal voltmeter has infinite internal resistance. A real voltmeter has a large but finite internal resistance and can be modeled as an ideal voltmeter in parallel with a resistor. In Fig. P 3.16,
R1 ¼ 10 kO; R2 ¼ 53 kO, and Rv ¼ 500 kO. The voltage across the series connection of R1 and R2 is fixed. When the (real) voltmeter is connected to R2, it reads 5.6 V. What is the true voltage across R2 (before the meter is connected)? P 3.26 In Fig. P 3.17, V0 ¼ 12 V and 900 O RL 1;200 O. The voltage vL must be 9 V 0:1 V. Specify the resistances R1, R2. What are the minimum and maximum currents drawn from the source? Use the nearest E192-series values for R1, R2 and calculate the resulting minimum and maximum values of the voltage vL. Does the circuit still meet the specifications? P 3.27 A simple model for a battery consists of an ideal voltage source in series with a resistance, called the internal resistance of the battery. The open-circuit (no-load) terminal voltage of the battery equals the terminal voltage of the ideal source. A battery having
74
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws i2
+ R1
V IS
R2
– Rx
i1
i4
b
a
A
c i3
Ry
Fig. P 3.18 See Problem P 3.28
i6
i5 d
iL iS
RS
Fig. P 3.20 See Problem P 3.30 + vL
load
RS
−
Fig. P 3.19 See Problem P 3.29
open-circuit (no-load) terminal voltage V0 is connected in series with a resistor having resistance RL. Using such a model, obtain expressions for the battery internal resistance Ri in terms of (a) the current IR through the resistor RL and (b) the voltage VR across the resistor. P 3.28 Refer to Fig. P 3.9. In Fig. P 3.18, R1 ¼ 10 kO and R2 ¼ 28 kO. The variable resistor Rx is adjusted until the ammeter reads zero, at which point the voltmeter reads 7.3 V and the resistance Rx ¼ 15:4 kO. Find the resistance Ry and the source current IS. P 3.29 Refer to Fig. P 3.19. Use Kirchhoff’s current law to show that the relation between the voltage vL and the current iL is independent of the load (of whatever is in the box). Section 3.7 is prerequisite for the following problems. P 3.30 Refer to Fig. P 3.20. Make d the reference node and write every relation you can think of among the node voltages and the voltages across the various elements; for example, vab ¼ va vb . Then write every relation you can think of among the branch currents; for example, i1 þ i2 þ i6 ¼ 0. P 3.31 Refer to Fig. P 3.21. Use Kirchhoff’s voltage law to express the voltage vL in terms of the current iL, the source voltage vS and the resistance RS. Note that the relation thus obtained is independent of the load (of whatever is in the box).
vS + –
iL
+ vL
load
–
Fig. P 3.21 See Problem P 3.31
iL
Rv
+ iS
Ri
vL –
+ v – S
Fig. P 3.22 See Problem P 3.32
P 3.32 Refer to Fig. P 3.22. According to Problem P 3.29, the relation between the voltage vL and the current iL is independent of the current iS and the resistance Ri. According to Problem P 3.31, the relation between the voltage vL and the current iL is independent of the voltage vS and the resistance Rv. Does this mean that the relation between the voltage vL and the current iL is independent of all four quantities vS ; Rv ; iS ; Ri ? From another point of view, the relation between the voltage vL and the current iL depends only upon vS, Rv and (simultaneously) only upon vS, Ri. How can this be? Explain. P 3.33 Refer to Fig. P 3.23. (a) Obtain symbolic expressions for the voltage vx and the current ix. (b) Let I0 ¼ 1mA; I1 ¼ 2mA; V0 ¼ 5V; V1 ¼ 2V; R0 ¼ 1 kO; R1 ¼ 2 kO. Calculate the values of the voltage vx and the current ix. P 3.34 : Use simulation to verify your answers to Problem P 3.33.
3.11 Problems
75 R0
R1
+ v – x I0
V0
R0 I1
R1
ix
(a)
R0
I0
R1
vx
R1 I1 ix
ix
+ vx
R0
–
R1
–
R0
V0
I1
R1 R0
I0 ix
(e)
R0 I0 V0
Fig. P 3.23 See Problem P 3.33
+
R1
R0 ix
(d)
–
(c)
R1
I1
vx
I1 V0
R0
+ vx –
V1
+ vx –
V1
(b) ix
V0
ix
I0
+ vx –
V 0 I0
ix
+
(f)
V0 + vx –
(g)
I0 R1
R0
(h)
+ vx – + –
+ –
ix
+
+ –
+ –
ix
vx – (b)
(a)
+ –
+ –
+ –
ix + –
–
ix
(c)
+
+ vx
+ –
+ + vx – –
(d)
vx
– + –
+ –
+ –
+ vx –
+ –
ix
ix
(e)
vx
(f)
–
+ –
+ –
ix (g)
+
+ vx ix
– (h)
vx
–
+ –
+ –
ix Fig. P 3.24 See Problem P 3.35
+ –
+ –
+ –
+
+ –
(i)
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws + –
76 ix
i0
2v0 R0
R0 +
vx
vx
–
2R1
R1 ix
R0
R0
+ –
R0
v0
R1
R1
R1
2v0 + –
+ v – 0
R1
2R1 ref (b)
(a) 2R1 i0
ix
+ vx
R0
R1 R0
–
R0
+ v – 0 R0
R0
2R0 2v0 + –
R1 R0
R1
vx
+ v – 0
R1
R0
+ R1
R0 + v – 0
– ix
Fig. P 3.25 See Problem P 3.36
P 3.35 Refer to Fig. P 3.24. (a) Obtain symbolic expressions for the current ix and the voltage vx. (b) Let each source voltage be 5 V and each source current be 10 mA. Calculate the values of the current ix and the voltage vx. P 3.36 : For each circuit in Fig. P 3.25: (i) Write the appropriate number of mesh (Kirchhoff’s voltage law) equations. (ii) Let v0 ¼ 1.5 V, i0 ¼ 1 mA, R0 ¼ 1 kO, R1 ¼ 16 kO. Calculate the mesh currents, the voltage vx, and the current ix. (iii) Use simulation to verify the results. P 3.37 : Repeat Problem P 3.36 using node analysis (Kirchhoff’s current law). Omit the simulations if you did them when working Problem P 3.36.
Section 3.8 is prerequisite for the following problems. P 3.38 It is required that the output of a voltage divider be between 74.5% and 75.5% of the input and that the total resistance be at least 400 kO. Assume that both resistors have the same precision (tolerance) and
(d)
+ v – 0 (c)
R1
+ vS
+ –
R2
RL
vL
–
Fig. P 3.26 See Problem P 3.39 iL iS
RS
RL
Fig. P 3.27 See Problem P 3.40
specify the values and precision of the least precise resistors that can be used. P 3.39 In Fig. P 3.26, R1 ¼ 100 kO 5%, R2 ¼ 300 kO 5%, and vS ¼ 5 V. (a) What is the smallest permissible value of the load resistance RL if the load voltage vL must be at least 70% of the source voltage vS? (b) If RL has the value determined in part (a), what is the maximum possible value of the load voltage? P 3.40 In Fig. P 3.27, RS ¼ 500 kO. What is the largest permissible value of the load resistance RL if
3.11 Problems
77
the load current iL must be at least 90% of the source current iS? P 3.41 In Fig. P 3.28, the source voltage V0 is constant and the voltmeter reads 5 V before the load RL is connected to the circuit. What does the voltmeter read after the load is attached? What is the source voltage V0? P 3.42 Refer to Fig. P 3.29, where the current I is fixed. Before the switch is closed, I1 ¼ 4 mA. After the switch is closed, the current I is unchanged. What is the new value of I1? What is the load current IL? What kind of source is driving this circuit? P 3.43 Refer to Fig. P 3.30, where V2 ¼ 5 V before the switch is closed. Find the value of k before the switch is closed. Find the value of k such that V2 ¼ 5 V after the switch is closed. P 3.44 Refer to Fig. P 3.31, where the switches are ganged (tied together), such that they open and close together. (a) Find R2 such that V2 ¼ 9 V when the
switches are open. (b) Then find R0 such that V2 remains equal to 9 V when the switches are closed. P 3.45 Refer to Fig. P 3.32, where the load resistance RL is nominally equal to 1 kO, but can vary by 30%. Other circuitry (not shown) must keep the load current IL equal to 80% of the source current I0 by adjusting the variable resistance R. What must be the range of R? P 3.46 Refer to Fig. P 3.33, where the load resistance RL is nominally equal to 5 kO, but can vary by 40%. Other circuitry (not shown) must keep the load voltage VL equal to 90% of the source voltage V0 by adjusting the variable resistance R. What must be the range of R? P 3.47 Refer to Fig. P 3.34. The load resistance RL varies randomly within the range 15 – 25 O. Other circuitry (not shown) monitors the load current IL and varies the source current I0 to keep the load current R0
R1
+ V0 –
V R2
RL
R1 = 1.0kΩ, R2 = 2.2kΩ, RL = 3.3kΩ
Fig. P 3.28 See Problem P 3.41
R1
V0 + –
R2
+ V2 –
RL
R1 = 2.2kΩ, RL = 3.9kΩ, V0 = 20V
Fig. P 3.31 See Problem P 3.44 IL
I
I1
I2
IL
R1
R2
RL
R1 = 1.0kΩ, R2 = 2.2kΩ, RL = 3.3kΩ
I0
RL
R
Fig. P 3.32 See Problem P 3.45
Fig. P 3.29 See Problem P 3.42 V0 (1− k)R
+ –
+
R
RL
VL –
kR
Fig. P 3.33 See Problem P 3.46
V0 + –
R1
R2
+ V2 –
IL
RL
I0
R0
RL
R1 = 2.2kΩ, R2 = 1.0kΩ, RL = 2.2k Ω, R = 10kΩ, V0 = 10 V
Fig. P 3.30 See Problem P 3.43
Fig. P 3.34 See Problem P 3.47
R0 = 100kΩ
78
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws
within 1% or 10 A. What must be the range of the source current? P 3.48 Refer to Fig. P 3.35. The load resistance RL varies randomly within the range 15 – 25O. Other circuitry (not shown) monitors the load voltage VL and varies the source voltage V0 to keep the load voltage within 1% of 20 V. What must be the range of the source voltage? P 3.49 Refer to Fig. P 3.36, where the temperature coefficients at 25 for R1 and R2 are 0.005 K1and 0:008 K1 , respectively. What is the maximum range of VL if the temperature of the circuit ranges from 25 C to 50 C? P 3.50 Refer to Fig. P 3.37. The resistor R2 is switched in and out, randomly. What is the percent variation of the voltage V1? P 3.51 Refer to Fig. P 3.38. The load current IL must not exceed 15 A, but can have any value less than 15 A without harm. The current I is nominally 10 A, but can occasionally jump to 50 A for a short time. Other circuitry (not shown) monitors the current I and closes the switch instantly if I exceeds 12 A, diverting some current through the resistor R. What is the maximum permissible value for R?
V0
+
R0
+ –
RL
VL R0 = 10 Ω
P 3.52 Explain why it is best to use resistors of the same kind (e.g., metal film, wirewound) in any particular voltage divider or current divider. Hint: Temperature is not necessarily constant. P 3.53 : It is proposed that a length of wire be used as the probe (sensor) in a temperature-measurement system, as illustrated in Fig. P 3.39, where RW is the resistance of the wire and the voltage v is to be measured as an indication of temperature. Assume the resistivity of the wire is given by rðTÞ ¼ r0 ½1 þ a0 ðT T0 Þ, where T is temperature in C and T0 ¼ 25 C. (a) Obtain an expression for the voltage v as a function of temperature in C. The source voltage VS, the source resistance RS, the parameters r0 and a0, and the length L and diameter d of the wire are presumed to be known. (b) Describe conditions under which the relation between temperature T and the measured voltage v is approximately linear (a straight-line relation). (c) Let Vs ¼ 12 V, Rs ¼ 100 O, r0 ¼ 1:543 mO cm, a0 ¼ 0:0044 C1 , L ¼ 1 m, and d ¼ 0:643 mm. Use a computer mathematics program to plot the voltage v versus probe temperature for 0 C T 20 C.
I IL
–
Fig. P 3.35 See Problem P 3.48
R
R1
RL = 10 Ω
Fig. P 3.38 See Problem P 3.51 +
V0 + –
R2
V0 = 25V
VL
R1 = 2.2kΩ ± 1%
–
R2 = 4.7kΩ ± 1%
Rs
Fig. P 3.36 See Problem P 3.49
+
V0 + –
R0
+ V – s
+ R1
V1
Rw
v –
R2
– R0 = 50 Ω, R1 = 1.0kΩ, R2 = 1.0kΩ, V0 = 25V
Fig. P 3.37 See Problem P 3.50
source
Fig. P 3.39 See Problem P 3.53
probe
3.11 Problems
79 R1
ix
ix R1
i0
vx i0
+ –
R0
R0
+ vx –
i0
R1
v0
R1
R0 vx
+ v – 0
ix R1
i1
R0
R0
+ – v0
(c) (b)
ix R1 + –
R0
R0 – v1 +
vx
v0
R0
R1
ix
+ vx – + v0 –
i0
v0
ix
i0
– +
(a)
vx R0
R1
i0
R0
(e)
Fig. P 3.40 See Problem P 3.54
(f)
(d)
R1 v0
R1 R0
i0
R0
R1
vx
vx i0
R0
R1 v0
R0
i0
ix
ix (a)
+
vx
(b)
–
R0
i0
R0
i1
v0
ix
v1
R1
v0
R1
ix
Fig. P 3.41 See Problem P 3.55
i1
vx
– vx +
R0 i0
v0
R0
R1 R1
i0
ix (e)
(c)
P 3.54 : Refer to Fig. P 3.40. (i) Obtain expressions for the voltage vx and the current ix in terms of circuit parameters. Show that the expressions are dimensionally consistent. (ii) Let i0 ¼ 5 mA; i1 ¼ 10 mA; v0 ¼ 5 V; v1 ¼ 10 V; R0 ¼ 1 kO; R1 ¼ 2:2 kO. Calculate the values of vx and ix. (iii) If you used node analysis in Part (ii), check your work using mesh analysis. If you used mesh analysis, check using node analysis. (iv) Simulate the circuit and verify the calculated values.
(d)
P 3.55 : Refer to Fig. P 3.41. (i) Obtain expressions for the voltage vx and the current ix in terms of circuit parameters. Show that the expressions are dimensionally consistent. (ii) Let i0 ¼ 5 mA; i1 ¼ 10 mA; v0 ¼ 5 V; v1 ¼ 10 V; R0 ¼ 1 kO; R1 ¼ 2:2 kO. Calculate the values of vx and ix. (iii) If you used node analysis in Part (ii), check your work using mesh analysis. If you used mesh analysis, check using node analysis. (iv) Simulate the circuit and verify the calculated values.
80
3 Circuit Elements, Circuit Diagrams, and Kirchhoff’s Laws
Section 3.9 is prerequisite for the following problems. P 3.56 Refer to Fig. P 3.42, where V0 ¼ 5 V, V1 ¼ 10 V, I0 ¼ 2 mA, I1 ¼ 5 mA, R0 ¼ 1 kO, and R1 ¼ 2:2 kO. Use superposition to find the voltage vx and the current ix. Verify your results with straightforward application of Kirchhoff’s laws. P 3.57 : Use simulation to verify your answers to Problem P 3.56. P 3.58 Refer to Problem P 3.23 for a description of a rheostat. In Fig. P 3.43, V1 ¼ 10 V, V2 ¼ 15 V, R1 ¼ 3:3 kO, R2 ¼ 2:2 kO, and R ¼ 5 kO. Find a value of k for which the current i equals zero. Is it possible to find such a value if V2 < 0? Show how or explain why not. P 3.59 Refer to Problem P 3.23 for a description of a rheostat. In Fig. P 3.44, I1 ¼ 10 mA, I2 ¼ 15 mA,
R1 ¼ 3:3 kO, R2 ¼ 2:2 kO, and R ¼ 5 kO. Find a value of k for which the current i equals zero. Is it possible to find such a value if I2 < 0? Show how or explain why not. P 3.60 Refer to Fig. P 3.45, where V0 ¼ 120 V, R0 ¼ 0:1 O, and the load resistance is nominally RL ¼ 10 O, but can vary by 50%. Additional monitoring circuitry (not shown) attempts to keep the load voltage between 100 and 125 V by switching sources in or out as the load resistance varies. (a) Construct graphs of load voltage versus number of switches in position b, for (i) RL ¼ 5 O, (ii) RL ¼ 10 O, and (iii) RL ¼ 15 O (on the same axes). (b) How many switches must be in position b in each case? (c) If the number of sources is unlimited, what is the maximum possible load voltage in each case? (d) Are there values of the load resistance for which it would be impossible to keep the load voltage between 100 and 125 V, and if so, what are they? (e) What is the minimum number of sources required for any load? vx
+ + vx – ix V0 + –
ix
R0
R0
V1
+ V1 –
+ –
–
R1
R0
R0
(a)
I1
(c) + vx – ix
I0
R0
I1
R1
ix
R1
+ vx
V0 + –
R0
R1
+ V – 1
I0
–
Fig. P 3.42 See Problem P 3.56
(b)
R1 V1 + –
(d)
R2
kR
(1−k)R
+ V2 –
I1
kR
R1
(1−k)R
i
I2
i
Fig. P 3.43 See Problem P 3.58
Fig. P 3.44 See Problem P 3.59 V0
V0
R0
a
b
S2
a
R0
+ –
S1
V0
R0
+ –
+ – b
Fig. P 3.45 See Problem P 3.60
R2
b
SN
a
+ RL
VL
–
3.11 Problems
81
IL
Fig. P 3.46 See Problem P 3.61
I0
P 3.61 Refer to Fig. P 3.46, where I0 ¼ 1 A, R0 ¼ 100 kO, and load resistance is nominally RL ¼ 500 O, but can vary by 30%. Monitoring circuitry (not shown) attempts to keep the load current between 3.75 and 4.5 A by closing or opening switches as the load resistance varies. (a) Construct graphs of load current versus number of switches closed for (i) RL ¼ 350 O, (ii) RL ¼ 500 O, and (iii) RL ¼ 650 O (on the same axes). (b) How many switches must be closed in each case, and what is
R0
I0
R0
I0
R0
RL
the actual load current in each case? (c) If the number of sources is unlimited, what is the maximum possible load current in each case? (d) Are there values of the load resistance for which it would be impossible to keep the load current between 3.75 and 4 A, and if so, what are they? (e) What is the minimum number of sources required for any load? (f) What load resistance would draw the minimum possible current within the range 3:5 A IL 4:5 A?
.
Chapter 4
Equivalent Circuits
Two-terminal elements or circuits having identical terminal characteristics are equivalent at their terminals. For example, any two-terminal element or circuit having the terminal characteristic v ¼ Ri, where v and i are voltage across and current through the terminals of the element and R is independent of v and i, is equivalent at those terminals to a resistor having resistance R. Equivalent elements or circuits cannot be distinguished by any measurements made at their terminals, and replacing one by the other in a larger circuit causes no change in any voltage or current in the rest of the circuit. In this chapter, we show how using equivalent circuits can simplify analysis. We introduce The´venin’s theorem, which permits reduction of any resistive circuit (at a terminal pair) to a voltage source in series with a resistor, and Norton’s theorem, which permits reduction of any resistive circuit (at a terminal pair) to a current source in parallel with a resistor. We begin with a discussion of terminal characteristics.
4.1 Terminal Characteristics Recall that the terminal characteristic for a twoterminal element is the relation the element establishes between voltage across and current into (or out of) the terminals. Recall also that the terminal characteristic for an element or circuit is independent of whatever is attached to the element or circuit at the terminals in question. For example, a resistor (idealized) obeys Ohm’s law, regardless of what is connected to the resistor. Similarly, the source voltage for an independent voltage source is independent of whatever is connected to the source.
To specify or determine a terminal characteristic, we must specify a direction for positive current in relation to the polarity assigned to terminal voltage. For a resistor, for example, the relation v ¼ iR holds if the positive direction of current is into the positive terminal of the resistor. If the positive direction for current is out of the positive terminal, then the terminal characteristic is v ¼ iR. For a resistor and some other circuit elements, the positive direction for current is conventionally into the positive terminal. But in general, choice of the positive direction for current in defining a terminal characteristic often depends upon whether we regard the element or circuit in question as a source or a load.1 Generally, if the element is regarded as a source, the positive direction of the terminal current is out of the positive terminal. If the element is regarded as a load, the positive direction of the terminal current is into the positive terminal. To obtain the terminal characteristic for a twoterminal element or circuit, we assign a polarity (þ/) to the terminal pair, assign a positive direction to current, and find the relation between the current and voltage thus defined (e.g., using Kirchhoff’s laws). Example 4.1. Obtain the terminal characteristic at the terminals a–b for the circuit shown in Fig. 4.1(a), regarding the circuit as a source.
1
Loosely, an element or circuit is regarded as a source if the element or circuit delivers energy to a circuit and is regarded as a load if it removes energy from the circuit (converts electrical energy to another form); e.g., a generator is ordinarily regarded as a source and a motor is ordinarily regarded as a load. As another example, from the perspective of an amplifier in a home audio system, a CD player is a source and a loudspeaker is a load.
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_4, # Springer ScienceþBusiness Media B.V. 2011
83
84
4 Equivalent Circuits i
a
v0
+ –
R0
v0
+ –
a +
R0
v
?
vc v vc þ ¼ i0 R0 R1
b
b
(a)
) vc ¼
–
R0 R1 R 0 þ R1
v þ i0 : R1
(b)
Eliminating vc yields Fig. 4.1 See Example 4.1
v R1 i ¼
Solution: Refer to Fig. 4.1(b). We identify terminal a as the positive terminal. Because we regard the circuit as a source, we take the positive direction of current out of the positive terminal. We assume an unspecified (arbitrary) load is attached to the terminals (to provide a closed path for current). From Kirchhoff’s voltage law, v0 þ R0 i þ v ¼ 0 ) i ¼
1 1 þ R1 R0
)i¼
1
v þ i0 R1
v R0 i0 : R1 þ R0
As in the previous example, a graphical representation of the terminal characteristic is a straight line, as shown in Fig. 4.4 (the graph is drawn for i0 > 0).
v0 v : R0
i
v0 /R0
Thus the terminal characteristic is expressed by i¼
v0 v R0
and displayed graphically as in Fig. 4.2.
Fig. 4.2 See Example 4.1
a
Example 4.2. Obtain the terminal characteristic at the terminals a–b for the circuit shown in Fig. 4.3, regarding the circuit as a load. Solution: We choose terminal a as the positive terminal and b as the reference. Because we regard the circuit as a load, we take the positive direction for current into terminal a. Writing Kirchhoff’s voltage law around the path defined by the terminals and the two resistors gives
v
v0
i
R1
c
+
+
v
vc
–
–
R0
i0
b
Fig. 4.3 See Example 4.2 i
R0 i0
v þ i R1 þ vc ¼ 0 ) vc ¼ v R1 i: To eliminate the node voltage vc, we write Kirchhoff’s current law at the node joining the two resistors. This gives
v −
R0 i0 R1+R0
Fig. 4.4 See Example 4.2
4.2 Equivalent Circuits
85
Exercise 4.1. Obtain the terminal characteristic at the terminals a–b for the circuit shown in Fig. 4.5, regarding the circuit as a source.
4.2 Equivalent Circuits Consider two circuits and designated terminal pairs, as shown in Fig. 4.6. The circuits are equivalent at designated terminal pairs if their terminal characteristics at those terminal pairs are identical; i.e., if the positive direction for current is the same (either into or out of the positive terminal) in both cases and the functions f1 ðvÞ; f2 ðvÞ are identical. Two circuits can be equivalent at some specified terminal pair(s) but not others. If the terminal pairs in question are clear from context, or if each circuit has only one terminal pair of interest (to the outside world), then we say simply that the circuits are equivalent. If we enclose two equivalent circuits in boxes, such that we have access to only the terminal pairs at which the circuits are equivalent, no electrical measurements at the terminals can distinguish one circuit from the other. Consequently, a collection of elements (a circuit) accessible by only a single
va
R0
i0
R1
a
ia
Fig. 4.5 See Exercise 4.1
a1
i
+
v
circuit 1
a2
v ¼ R1 i þ R2 i þ RN i ¼ ðR1 þ R2 þ þ RN Þi: Thus the terminal characteristic and equivalent resistance for the series connection are given by
–
b1
v ; Req
Req ¼ R1 þ R2 þ þ RN :
(4.1)
+
v
circuit 2
– i = f1 (v)
Refer to Fig. 4.7, which shows a circuit consisting of a series connection of N resistors. We seek the terminal characteristic of the circuit at the terminals a–b. We regard the circuit as a load, so we take the positive direction for current into the positive terminal of the circuit. Because the same current passes through each element in a series connection, it follows from Ohm’s law and Kirchhoff’s voltage law that the voltage across the series connection of resistors is
This result shows that a series connection of N resistors is equivalent to a single resistor whose resistance is the sum of the resistances in the series connection. That is, for Req given by (4.1), the two circuits in Fig. 4.7 have the same terminal characteristic at the terminals a–b. Thus, wherever we encounter a series connection of resistors, we can replace the series connection by a single equivalent resistor, simplifying the circuit.
b
i
4.2.1 Resistors in Series Are Additive
i¼
2R0
+ v – 0
terminal pair can be replaced by an equivalent collection of elements without altering the behavior of the circuit as a whole. Often, a large number of elements can be replaced (mathematically, at least) by a much smaller number of elements, facilitating further analysis and interpretation of results. In this section, we show how various two-terminal resistive circuits can be reduced to simpler, equivalent twoterminal circuits. Such reductions often simplify circuit analysis and design.
b2 i = f2 (v)
Fig. 4.6 Two two-terminal circuits having terminal characteristics f1(v), f2(v)
4.2.2 Conductances in Parallel Are Additive Refer to Fig. 4.8, which shows a parallel connection of N resistors. Because the same voltage exists across
86
4 Equivalent Circuits
Fig. 4.7 Resistors in series are additive. See (4.1)
R2
RN
RN
i
a +
v
i
Req
b –
i R1
R2
R1
a +
v
i
a +
Req
b –
Fig. 4.8 Conductances in parallel are additive. See (4.4)
v b –
Req ¼ R1 kR2 ¼
v b –
a +
R1 R2 : R1 þ R2
(4.6)
The expression R1 k R2 is read or said as “R1 in parallel with R2”.
elements in parallel, it follows from Ohm’s law and Kirchhoff’s current law that
Example 4.3. Obtain a single, equivalent resistance at the terminals a–b for the circuit of Fig. 4.9.
i ¼ G 1 v þ G 2 v þ þ GN v ¼ ðG1 þ G2 þ þ GN Þv;
Solution: From (4.6), an equivalent, single resistance for the parallel connection of R2 and R3 is
(4.2)
where Gn ¼ Rn 1 . Equation (4.2) may be written as i ¼ Geq v;
Geq ¼ G1 þ G2 þ þ GN :
(4.3)
This result shows that the conductances of resistors in parallel are additive. Thus the equivalent resistance of resistors in parallel is given by
Ra ¼
R2 R3 : R2 þ R3
This equivalent resistance is in series with R1 and R4. Thus the equivalent resistance at terminals a–b is Req ¼ R1 þ R4 þ Ra :
1 1 1 1 ¼ þ þ þ : Req R1 R2 RN
(4.4)
For Req given by (4.4), the two circuits in Fig. 4.8 have the same terminal characteristic at the terminals a–b. Resistors in parallel are encountered often, especially in analysis of electronic circuits, so it is convenient to have a shorthand notation for the cumbersome relation (4.4). The notation Req ¼ R1 kR2 kR3 k kRN 1 1 1 1 ¼ þ þ þ ) Req R1 R2 RN
(4.5)
is widely used, at least in practice. This notation does not speed computation, but often facilitates interpretation of circuit equations. For the special (but important) case N ¼ 2, (4.4) gives
Example 4.4. Obtain an expression for the equivalent resistance at the terminals a–b of the circuit shown in Fig. 4.10. Solution: Figure 4.11 illustrates steps in the solution. The resistors R2, R3 are connected in parallel. The equivalent resistance for the parallel connection is given by (see (4.6)) Ra ¼
R2 R3 : R2 þ R3
The equivalent resistance for the series connection of Ra, R4 is given by Rb ¼ Ra þ R4 ¼
R2 R3 þ R4 : R2 þ R3
4.2 Equivalent Circuits
87 R1
R2 R1
R3
R4
R2
a
b
R0
Fig. 4.9 See Example 4.3
R4
b
a
v1
v2 + –
R3
+ –
R1
R2
Fig. 4.12 See Exercise 4.2
R2 a
2R0
b
vN
b
+ –
a
⇓
R5
veq + –
a
b
Fig. 4.10 See Example 4.4 Fig. 4.13 Voltage sources in series are additive a
R1
Ra
R4
b
R5
a
R1
Req ¼ R1 þ Rc ¼ R1 þ
Rb
b
R5
a
R1
Rc
b
Req
a
Exercise 4.2. Obtain an expression for the equivalent resistance at the terminals a–b of the circuit shown in Fig. 4.12.
b
4.2.3 Voltage Sources in Series Are Additive
Fig. 4.11 See Example 4.4
The equivalent resistance of the parallel connection of Rb, R5 is given by
R2 R3 þ R4 R5 Rb R5 R2 þ R3 Rc ¼ ¼ R2 R3 Rb þ R5 þ R4 þ R5 R2 þ R3 ¼
½R2 R3 þ R4 ðR2 þ R3 Þ R5 : R2 R3 þ ðR2 þ R3 ÞðR4 þ R5 Þ
½R2 R3 þ R4 ðR2 þ R3 Þ R5 : R2 R3 þ ðR2 þ R3 ÞðR4 þ R5 Þ
Finally, the equivalent resistance of the series connection of R1, Rc is given by
Applying Kirchhoff’s voltage law to the top circuit in Fig. 4.13 yields vab ¼ v1 þ v2 þ þ vN :
(4.7)
A series connection of voltage sources is equivalent to a single voltage source whose source voltage equals the sum of the original source voltages. Whenever ideal voltage sources appear in series in a circuit, they can be replaced by a single voltage source whose source voltage is the algebraic sum of the original source voltages. We do not consider voltage sources in parallel because such an arrangement contradicts the definitions of both a parallel connection and an ideal voltage source
88
4 Equivalent Circuits
(unless all the sources are identical, in which case any one of them would do).
4.2.4 Current Sources in Parallel Are Additive Applying Kirchhoff’s current law to the circuit on the left in Fig. 4.14 yields ieq ¼ i1 þ i2 þ þ iN ;
(4.8)
which shows that any number of current sources in parallel can be reduced to a single current source, where the source current equals the sum of the source currents for the original (constituent) sources. In any circuit where ideal current sources appear in parallel, they can be replaced by a single current source whose source current is the algebraic sum of the original source currents. We do not consider current sources in series because such an arrangement contradicts the definition of a series connection (unless all the sources are identical, in which case any one of them would do). The sums in (4.7) and (4.8) are algebraic. If the polarity of a voltage source in Fig. 4.13 or the direction of a current source in Fig. 4.14 is reversed, the corresponding term in the associated sum must be negated.
4.2.5 Elements in Series Commute, as do Elements in Parallel
series connection. Conductances in parallel add, as do current sources in parallel, no matter how ordered in the parallel connection. For example, the series circuits in Fig. 4.15 are equivalent at the terminals a–b, as are the parallel circuits in Fig. 4.16. Example 4.5. Simplify the circuit shown in Fig. 4.17; that is, find a simpler circuit that is equivalent at the terminals a–b to the circuit shown. Solution: See Fig. 4.18. We first combine the parallel elements to obtain the circuit of Fig. 4.18(a), where ð3 RÞð5 RÞ 15 R ¼ ; 3R þ 5R 8 ð4 RÞð5 RÞ 20 R Rb ¼ ¼ : 4R þ 5R 9 Ra ¼
The two rightmost current sources add to give a net (downward) current 5 i0 3 i0 ¼ 2 i0 . We then combine the series elements to obtain the circuit of Fig. 4.18(b), where R c ¼ 2 R þ Ra ¼
The two voltage sources add to give a net voltage (positive on the left). 2 v0 v0 ¼ v0 .
v1
a
v2
R1
i1
i2 ...
R1 + R2 v1− v2
b
+ –
ieq
a
R2
+ –
+ –
Commuting two elements means swapping their places in a circuit. If the resulting circuit is equivalent to the original, we say the swapped elements commute. Resistors and sources in series commute, as do resistors and sources in parallel; that is, the terminal characteristic of a series (or parallel) connection of such elements is independent of the order in which the elements are connected. Consequently, resistors in series add, as do voltage sources in series, no matter how ordered in the
31 R : 8
Fig. 4.15 Equivalent series circuits a
i1
R1
i2
R2
b a
a
iN
a
i1 − i2
ieq = i1+ i2 + . . . + iN b
Fig. 4.14 Current sources in parallel are additive
b
b
Fig. 4.16 Equivalent parallel circuits
R1 R2 R1 + R2
b
4.2 Equivalent Circuits
89 3R
v0
2R
5R
a
+ –
+ –
2i0
2v0
R
5R
3i0
4R
5i0 b
Fig. 4.17 See Example 4.5
v0
Ra
+ –
+ –
2R 2i0
2v0
R
a 2i0
Rb
b
(a) original circuit
v0 a
+ –
Rc 2i0
Rb
R
2i0
known voltage source v to the terminal pair and measuring or calculating the resulting current i into the terminal pair. Alternatively, we may attach a known current source i and measure or calculate the resulting voltage v across the terminal pair. In either case, the equivalent resistance is given by Req ¼ v=i as illustrated by Fig. 4.20. This approach is useful when a circuit cannot be simplified further by reducing series and parallel connections of resistors to single, equivalent resistors, as illustrated by the next example.
b
(b) simplified circuit
Fig. 4.18 See Example 4.5
Using only methods described above, we cannot simplify the circuit further; e.g., the two remaining current sources are not in parallel because the same voltage does not appear across both. In Section 4.3, we show how such circuits can be simplified further.
Example 4.6. Find the equivalent resistance at the terminals a–b of the circuit shown in Fig. 4.21(a). Solution: We attach a known voltage source v to the terminals a–b, as shown in Fig. 4.21(b), obtain an expression for the current i, and use Req ¼ v/i. With reference to Fig. 4.21(b), Kirchhoff’s current law gives i ¼ ix þ iy ¼
Exercise 4.3. Find values of a, b, g, d such that the circuits shown in Fig. 4.19(a) and Fig. 4.19(b) are equivalent at the terminals a-b.
4.2.6 Finding Equivalent Resistance Using a Known Source If the current into the positive terminal and voltage across a terminal pair of a device or circuit obey a relation of the form i ¼ v=R, then by definition the device or circuit is equivalent to a resistor having resistance R at the terminal pair in question. If it is known in advance that a particular device or circuit is equivalent to a resistor at a particular terminal pair, then we can find the equivalent resistance, either experimentally or mathematically, by attaching a
v vx v v y þ ; R 2R
where b is the reference node. Writing Kirchhoff’s current law for nodes x and y gives vx v vx vy vx þ ¼ 0; þ 5R 4R R vy v vy vx vy þ ¼ 0; þ 5R 3R 2R which yield vx ffi 0:777 v; vy ffi 0:634 v: Thus iffi
v 0:777 v v 0:634 v v þ ffi 0:406 R 2R R
which gives Req ¼
v R ffi ffi 2:46 R: i 0:406
90
4 Equivalent Circuits R 4R
v0
+ –
bR
R
a
3v0
2R
3R
+
+ –
v
i
–
(a) Using a known voltage
(b) Using a known current
source
source
Fig. 4.20 Finding the equivalent resistance Req ¼ v/i at a terminal pair
a
i
a
ix
4R
2R
R
2R
v
5R
iy
+ –
5R
y
x
3R
4R
3R b = ref
b
(a)
(b)
Fig. 4.21 See Example 4.6 2R
a
d i0
gR
b
+ –
i
R
a v0 +–
2R
b (b)
(a)
Fig. 4.19 See Exercise 4.3
v
i0
a
series connection. If the resistance of one resistor in a series connection is much larger than the total resistance of the others, the equivalent resistance of the series connection often can be approximated by that of the larger resistor. Similarly, the resistance of a parallel connection of resistors is smaller than the smallest single resistance in the connection. If the resistance of one resistor in a parallel connection is much smaller than that of the equivalent resistance of the others, the equivalent resistance of the parallel connection often can be approximated by that of the smaller resistor. In making these approximations, the meanings of “much larger than” and “much smaller than” depend upon the application at hand. Sometimes, a factor of 10 is sufficient; for example, if R2 > 10 R1 , then R1 þ R2 (series connection) often can be approximated by R2 and R1 R2 =ðR1 þ R2 Þ (parallel connection) by R1. More often, a factor of 100 is sufficient, and almost always, a factor of 1000 is more than sufficient. As R2 ranges from 10 R1 to 1000 R1, the error in these approximations ranges from about 10% to about 0.1%. Such approximations often provide useful checks on the results of more exact calculations.
20R 3R 30R 7R
Fig. 4.22 See Exercise 4.4
b
Exercise 4.4. Refer to Fig. 4.22, where R ¼ 1O. Find the equivalent resistance at the terminals a–b.
4.2.7 Approximations The resistance of a series connection of resistors is larger than the largest single resistance in the
Example 4.7. (a) Find the equivalent resistance at the terminals a–b for the circuit shown in Fig. 4.23. (b) Check the result using reasonable approximations. Solution: (a) The equivalent resistance is Req ¼ R1 þ R4 þ
R2 R3 ffi 10:6 kO: R 2 þ R3
(b) Because R3 R2 we approximate the parallel connection of those resistors by R3 alone, which then appears in series with R1 and R4 Because R1 R3 þ R4 the equivalent
4.3 Source Transformations
91 R3
R1
R2
R1 = 10 kΩ
a R4 b
R3 = 100 Ω R4 = 500 Ω
R1
R
v0
+
v
i0
–
(a)
R
v –
(b)
Fig. 4.25 Equivalent source models: i0 ¼ v0/R
+ i0
+ –
R2 = 2 kΩ
Fig. 4.23 See Example 4.7
R0
i
i
+
vx i1
R2
–
Fig. 4.24 See Exercise 4.5
resistance at the terminals a–b is approximately R1 ¼ 10 kO. The result obtained in (a) above is reasonable. (Also, the error in the approximation is only about 6%). Similar approximations can be made for voltage sources in series, where the magnitude of one source voltage is much larger than the sum of the others, and for two current sources in parallel, where the magnitude of one source current is much larger than the sum of the others. Exercise 4.5. Refer to Fig. 4.24, where R0 R2 , i1 i0 . (a) Obtain an exact expression for vx. (b) Find a reasonable approximation to vx. (c) Let R0 ¼ 10 kO, R1 ¼ 5 kO, R2 ¼ 4:7 O, i0 ¼ 1 mA, i1 ¼ 100 mA. What is the percentage error in the approximation?
4.3 Source Transformations In this section, we show that a voltage source in series with a resistor is equivalent to a current source in parallel with an identical resistor. This equivalence allows what are called source transformations, which, in conjunction with methods described above, often can be used to reduce a complex circuit to a much simpler one.
We wish to show that the circuits inside the dotted boxes in Fig. 4.25 are equivalent at their terminals if i0 ¼ v0 =R and the two resistors are identical. The gray boxes represent arbitrary (unspecified) elements or circuits. Writing Kirchhoff’s voltage law for the circuit in Fig. 4.25(a) gives v0 þ i R þ v ¼ 0; which yields i¼
v v0 þ : R R
(4.9)
Writing Kirchhoff’s current law for the circuit in Fig. 4.25(b) gives i0 þ
v þ i ¼ 0; R
which yields i¼
v þ i0 : R
(4.10)
The terminal characteristics (4.9) and (4.10) are identical (the circuits in Fig. 4.25 are equivalent at the terminals a–b) if i0 ¼ v0/R. The significance of the development above is the following: Whenever we wish, we may replace a voltage source in series with a resistor with a current source in parallel with an identical resistor, or vice-versa, as illustrated by Fig. 4.26. Such source transformations, in conjunction with reduction of series and parallel connections as described above, can be useful in circuit analysis. But note that an isolated voltage source (no series resistance) cannot be transformed to a current source. Similarly, an isolated current source (no parallel resistance) cannot be transformed to a voltage source. This is not a serious limitation, because all realistic source models possess internal resistance.
92
4 Equivalent Circuits
+ –
+ –
R
a
a
i0 = v0 /R
v0
i0 b
R1
v1 +–
R
i1
R2
+
R3
v2
R4
v –
v0 = Ri0
b
+ –
Fig. 4.26 Source transformations. Note the polarity of the voltage source and the direction of the current source. If either is reversed, the other is also
(a)
i3
R1
i1
R2
R3
v2
+ R4
v –
(b) + –
Example 4.8. Obtain an expression for the voltage v in the circuit of Fig. 4.27(a).
i4
Ra
+
R3
v2
R4
v –
Solution: We proceed as shown in Fig. 4.27 (b)–(e): We transform the voltage source v1 and series resistor R1 to an equivalent current source and parallel resistor R1, as shown in Fig. 4.27(b), where
(c) + –
v3
+ –
Ra
+ R3
v2
R4
v –
(d)
i3 ¼ v1 =R1 :
(4.11) v4 +–
We combine the parallel current sources i1, i3 and resistors R1, R2, as shown in Fig. 4.27(c), where R1 R2 i4 ¼ i1 þ i3 ; Ra ¼ : R1 þ R2
R4
(e)
v¼
R4 ½R1 R2 i1 þ R2 v1 þ ðR1 þ R2 Þv2 : ðR4 þ R3 ÞðR1 þ R2 Þ þ R1 R2
(4.13)
(4.14)
Exercise 4.6. Simplify the circuit of Fig. 4.19(a) at the terminals a–b to (a) a resistance RT in series with a voltage source vT (positive polarity nearest terminal a) and (b) a resistance RN in parallel with a current source iN (arrowhead pointing to the conductor attached to terminal a).
The circuit shown in Fig. 4.27(e) is a voltage divider. Thus we have v¼
R4 v4 ; R4 þ Rb
(4.15)
which, using (4.11) through (4.14), yields
v –
(4.12)
We add the series voltage sources and add the series resistors to obtain the circuit shown in Fig. 4.27(e), where v4 ¼ v3 þ v2 ; Rb ¼ Ra þ R3 :
+
Fig. 4.27 See Example 4.8
We transform the current source i4 and parallel resistor Ra to a voltage source and series resistor as shown in Fig. 4.27(d), where v 3 ¼ R a i4 :
Rb
Example 4.9. Refer to Fig. 4.28. (a) Find the voltage across the load resistor RL. (b) Repeat, using reasonable approximations, and compare with the result obtained in (a).
4.4 The´venin and Norton Equivalent Circuits
93 R1 = 10 Ω
R1
R2 = 1 kΩ
v1 + –
i1
R2
RL = 40 Ω
RL
v1 = 5 V
i1 = 5 mA
ieq ffi
Fig. 4.28 See Example 4.9
v1
R1
R1
i1
Thus we ignore the current source i1 and the resistor R2. Then with reference to Fig. 4.30, we have that
R2
RL
v1 R1
= 500 mA
Thus the load current and load voltage are (approximately) iL ffi
Fig. 4.29 See Example 4.9
Req v1 R1 v1 ¼ ¼ 100 mA; Req þ RL Req R1 þ RL R1
vL ¼ iL RL ¼ 4:00 V: iL
ieq
v1 ¼ 100 mA; Req ffi R1 ¼ 10 O: R1
Req
RL
Fig. 4.30 See Example 4.9
Solution: Refer to Fig. 4.29. We transform the voltage source in series with resistor R1 to an equivalent current source in parallel with resistor R1, as shown in Fig. 4.29. (a) The circuit shown in Fig. 4.29 reduces to the current divider shown in Fig. 4.30, where v1 þ i1 ffi 505 mA; R1 R1 R2 Req ¼ ffi 9:90 O: R1 þ R2
The error in the approximation is about 0.2% for the load current and about 0.25% for the load voltage. Again, even in cases where errors introduced by approximations are intolerable, finding an approximate solution often provides a good check on the reasonableness of a more exact result. You should make it a habit to perform such checks, in addition to dimension checks and limit checks.
4.4 The´venin and Norton Equivalent Circuits
ieq ¼
The load current and load voltage are iL ¼
Req ieq ffi 100:2 mA; Req þ RL
vL ¼ iL RL ffi ð100:2 mAÞð40 OÞ ffi 4:01V: (b) In the circuit shown in Fig. 4.29, v1 ¼ 500 mA i1 ; R1
R1 R2 :
A resistive circuit is a circuit containing only resistors and sources. Figure 4.31 shows an arbitrary resistive circuit. We choose any terminal pair a–b that satisfies Kirchhoff’s current law, meaning that the current exiting one terminal equals the current entering the other. The´venin’s theorem states that the terminal characteristic at such a terminal pair is i v ¼1 ; isc voc
(4.16)
where i and v are the terminal current and voltage, respectively, and isc and voc are the short-circuit current and the open-circuit voltage at the terminals a–b, whose definitions are illustrated by Fig. 4.32. It does not matter what is in the two-terminal gray box
94
4 Equivalent Circuits RT
a
i
+
Fig. 4.33 Pertaining to the definition of a The´venin equivalent circuit
v
resistive circuit i
i
+
–
+ –
vT
v –
b
Fig. 4.31 Pertaining to The´venin’s theorem (see (4.16))
a
a
resistive circuit
resistive circuit
isc
+ voc –
b
b
(a) short-circuit current
(b) open-circuit voltage
Fig. 4.32 Definitions of short-circuit current and open-circuit voltage
which, for present purposes, simply provides a path for the terminal current i. The´venin’s theorem is among the most important derived results in electrical engineering. Essentially, The´venin’s theorem states only that the relation between terminal voltage and terminal current is given by (4.16). The theorem says nothing about the internal structure of the circuit, except that it contains only resistors and sources. Nonetheless, it is useful to interpret (4.16) as the terminal characteristic of what is called the The´venin equivalent for the actual circuit in question, as follows: We write (4.16) as
voc v ¼ voc i; isc
(4.17)
v ¼ vT RT i;
(4.18)
and then as
or as i¼
v vT þ ; RT RT
(4.19)
where vT ¼ voc ¼ Thevenin equivalent voltage; (4.20) voc RT ¼ ¼ Thevenin equivalent resistance: isc
We may interpret (4.18) as Kirchhoff’s voltage law written for the circuit shown in Fig. 4.33. From this perspective, The´venin’s theorem and (4.20) state that a two-terminal resistive circuit is equivalent at the terminals to a voltage source vT in series with a resistor RT. Again, it does not matter what is in the two-terminal gray box which, for present purposes, simply provides a path for the terminal current i. This development leads to the following restatement of The´venin’s theorem: Any resistive circuit is equivalent at any particular terminal pair satisfying Kirchhoff’s current law to an independent source in series with a resistor, where the source voltage and the resistance of the resistor are given by (4.20). The source voltage RT is called the The´venin equivalent voltage and the resistance RT of the resistor is called the The´venin equivalent resistance. The combination of the source and resistor is called the The´venin equivalent circuit at the terminal pair under consideration. A The´venin equivalent voltage is called the The´venin voltage, a The´venin equivalent resistance is called the The´venin resistance, and a The´venin equivalent circuit is called the The´venin equivalent. A circuit can have more than one terminal pair. A The´venin equivalent for such a circuit is specific to the terminal pair chosen. Neither the The´venin equivalent voltage source nor the The´venin equivalent resistance is necessarily physical. That is, neither necessarily corresponds to any particular element in the associated physical circuit. A The´venin equivalent should be viewed simply as a means of depicting the fundamental relation (4.16) by a circuit diagram. The usual purpose of representing a circuit by its The´venin equivalent is to treat the circuit as a source to which a load is to be attached; e.g., to study current and voltage delivered by the circuit to various loads. Consequently, the positive direction for current in the terminal characteristic (4.19) for a The´venin equivalent is conventionally out of the positive terminal, as shown in Fig. 4.33.
4.4 The´venin and Norton Equivalent Circuits
95 i0
i0
R
v0
a 2R
+ –
R
a 2R
v0
R
R
R R
R b
b
(a) 2R i0
5R / 2
v0 2
a
a
+ –
R/2
(b)
2R
+ –
v0
R
2
−2R i0 +–
R b
b (c)
Fig. 4.34 See Example 4.10
The The´venin equivalent for a circuit is unique. We may use any workable method to find the The´venin equivalent circuit parameters RT, including straightforward application of Kirchhoff’s laws, reducing series and parallel connections to simpler equivalents, and source transformations.
Example 4.10. Obtain the The´venin equivalent for the circuit of Fig. 4.34(a) at the terminals a–b. Solution: We use source transformations and series-parallel reductions to simplify the circuit as illustrated by Fig. 4.34(b)–(d). The circuit of Fig. 4.34(d) is a voltage divider and the open-circuit voltage is given by voc ¼
v 2 v R 0 0 2R i0 ¼ 2R i0 : R þ 5R=2 2 7 2
(d)
Exercise 4.7. Obtain the The´venin equivalent for the circuit of Fig. 4.35 at the terminals a–b. The terminal characteristic of a two-terminal circuit is a property of the circuit and is independent of any attachment to the terminals. A heuristic proof of The´venin’s theorem based upon this fact follows: We attach an independent voltage source v to the terminals a–b of a resistive circuit, as illustrated by Fig. 4.36. We assume that the terminals a–b are neither shorted nor open nor connected directly to another source inside the box, in which case the source voltage v is the terminal voltage. Together, the circuit in the box and the source v comprise a resistive circuit, so the terminal current i is a linear function of all the sources in the box and of the source v; that is, the terminal current is given by2 i ¼ a1 v1 þ a2 v2 þ þ aN vN þ b1 i1 þ b2 i2 þ þ bM iM þ m v;
The short-circuit current is given by v
0
isc ¼
2
2 R i0 5R=2
¼
ðv0 4 R i0 Þ : 5R
Thus the The´venin voltage and The´venin resistance are given by v 4Ri 2 v0 0 0 vT ¼ voc ¼ 2Ri0 ¼ ; 7 2 7 7 RT ¼
voc 5R ¼ : 7 isc
where v1 ; v2 ; ; vN are all of the voltage sources inside the box and i1 ; i2 ; ; iM are all of the current sources inside the box. All these sources are fixed, and we may write the relation above more simply as i ¼ m v þ b;
(4.21)
where b ¼ a1 v1 þ a2 v2 þ þ aN vN þ b1 i1 þ b2 i2 þ þ bM iM . The relation above describes a straight 2
See Section 3.10 in Chapter 3.
96
4 Equivalent Circuits + –
right in Fig. 4.37 yields the terminal characteristic for a Norton equivalent circuit:
v1
R
a + –
i¼
4R
i0
v0
b
v þ iN : RN
(4.24)
From (4.24), the Norton source current iN is the short-circuit current: iN ¼ isc :
Fig. 4.35 See Exercise 4.7
(4.25)
From Fig. 4.26, the transformation relations are i
resistive circuit
Fig. 4.36 Pertaining to the development of The´venin’s theorem
a + –
v
iN ¼
vT ; RT
(4.26)
b
line whose slope m and intercept b can be determined using any two points on the line. Setting v ¼ 0 in (4.21) is equivalent to shorting the terminals a–b and gives i ¼ b, so the parameter b is the short-circuit current; i.e., b ¼ isc :
(4.22)
Setting v to the open-circuit voltage voc is equivalent to opening the terminals, in which case i ¼ 0 and (4.21) becomes voc ¼ b=m ¼ isc =m, which yields m¼
isc : voc
(4.23)
From (4.21–4.23), i¼
RN ¼ RT ;
isc v þ isc : voc
Dividing both sides of (4.23) by isc and rearranging terms gives (4.16). Using a source transformation, the The´venin equivalent for a circuit can be transformed to a current source in parallel with a resistor, as shown in Fig. 4.37. The resulting circuit is called the Norton equivalent circuit or simply the Norton equivalent. The source current iN is called the Norton current and the resistance RN is called the Norton resistance. Writing Kirchhoff’s current law for the circuit on the
which are just the usual source-transformation relations made specific to the notation used here. Figure 4.37 illustrates relations between the The´venin and Norton equivalents for the same circuit. In general, elements comprising the The´venin or Norton equivalent for a circuit are non-physical and do not correspond to components in an associated physical circuit. As noted above, a circuit regarded as a source often is represented by the The´venin or Norton equivalent for the circuit. In this context, the The´venin (or Norton) equivalent resistance for the circuit also is called the internal resistance, the output resistance, or the source resistance of the circuit (the source). Generally, the term internal resistance is used in reference to the The´venin or Norton equivalent for a physical source, such as a battery, a power supply, or an electric generator, and the term output resistance is used when the source in question is a circuit. For example, we might refer to the internal resistance of an alkaline battery and the output resistance of an audio amplifier (at the speaker terminals). The term source resistance often is used in either case or when the nature of the source is unspecified. But the terminology police do not vigorously enforce these conventions, and you may treat internal resistance, output resistance, and source resistance as synonyms without fear of arrest and imprisonment. Example 4.11. Obtain the Norton equivalent for the circuit of Example 4.10 at the terminals a–b.
4.4 The´venin and Norton Equivalent Circuits
97 a
a
vT Fig. 4.37 The´venin and Norton equivalent circuits
+ –
RT
RN = RT
iN
iN = vT / RT
RN b
b
2R
Solution: The Norton current is the shortcircuit current. The Norton resistance is the The´venin resistance. From Example 4.10 iN ¼ isc ¼
ðv0 4 R i0 Þ ; 5R
i1 + –
RN ¼ RT ¼
5R : 7
i3
a
R
x
b
R
i2
v0
i5
i4
+ voc
2R
– y (a)
2R
Exercise 4.8. Obtain the Norton equivalent for the circuit of Exercise 4.7 at the terminals a–b.
i1 + –
i3
a
R
R
i2
v0
i5
i4
x
b isc
2R
Example 4.12. Obtain the The´venin and Norton equivalents at the terminals x–y for the circuit of Fig. 4.38, where R ¼ 10 kO and v0 ¼ 25 V. Solution: We find the The´venin equivalent by finding the open-circuit voltage and the shortcircuit current. First, we find the open-circuit voltage. We label the nodes as shown in the figure and select node c as the reference node. Writing Kirchhoff’s current law at nodes a and b gives G va þ Gðva vb Þ ¼ 0; 2 G Gðvb va Þ þ ðvb v0 Þ ¼ 0; 2 Gðva v0 Þ þ
where G ¼ R1 Upon dividing both equations by G/2 and collecting terms, we obtain 5 va 2 vb ¼ 2v0 ; 2 va þ 3 vb ¼ v0 :
y (b)
Fig. 4.38 Circuit of Example 4.12: (a) With the terminals x–y open for calculating the open-circuit voltage voc and (b) with the terminals x–y shorted for calculating the short-circuit current isc
The open circuit voltage is voc ¼ vbc ¼ vb. We eliminate va and obtain voc ¼ vb ¼
9 v0 : 11
To determine the short-circuit current, we short the terminals x–y as shown in the figure. With the terminals shorted, vb ¼ 0. Writing Kirchhoff’s current law at node a leads to 5 2 v0 va ¼ v0 ) va ¼ : 2 5 Writing Kirchhoff’s current law at node b (with vb ¼ 0) gives i4 þ i5 þ isc ¼ Gðva Þ þ
G ðv0 Þ þ isc ¼ 0; 2
98
4 Equivalent Circuits
which yields isc ¼ G va þ
G 2 v0 v0 9 v0 þ ¼ ; v0 ¼ 5 R 2R 10 R 2
where we have used the value for va obtained above. Thus we have 9 v0 ffi 20:5 V; 11 9 v0 iN ¼ isc ¼ ffi 2:25 mA; 10 R voc 10R ¼ ffi 9:09 kO: RT ¼ RN ¼ isc 11 vT ¼ voc ¼
Figure 4.39 shows a graph of the terminal characteristic for a The´venin or Norton equivalent circuit. You will find it helpful to memorize Fig. 4.39. From (4.19) or from (4.24), the The´venin or Norton equivalent resistance for a circuit is the negative reciprocal of the slope of the terminal characteristic: 1 di voc ¼ : RT ¼ RN ¼ isc dv
(4.27)
This relation helps us remember that the internal resistance of an independent voltage source equals zero (because the terminal characteristic is a vertical line and di=dv ! 1) and that the internal resistance of an independent current source is infinite (because the terminal characteristic is a horizontal line and di=dv ¼ 0). The general form of the terminal characi = isc – isc
teristic of a resistive circuit, given by (4.16), is easily deduced from the graph in Fig. 4.39. Although the graph in Fig. 4.39 suggests that the short-circuit current and the open-circuit voltage are both positive, that is not necessarily the case. Both can be negative, in which case we would draw the equivalent circuits and a graph of the terminal characteristic as shown in Fig. 4.40. For a resistive circuit, the opencircuit voltage and the short-circuit current must have the same sign. (Why?) The The´venin equivalent for a circuit can be obtained experimentally, by measuring two pairs of i–v values. Any two pairs will do, because the terminal characteristic is a straight line, as shown by Fig. 4.39. Although open-circuit voltage and shortcircuit current are convenient values for mathematical analysis, it may be unwise to attempt to measure short-circuit current at the terminals of a physical circuit. The next example shows how one obtains the The´venin equivalent for a circuit from an arbitrary pair of i–v values. Example 4.13. The two pairs of values vi, i1 and v2, i2 are measured at a terminal pair of a resistive circuit. Obtain an expression for the The´venin equivalent at the terminal pair. Solution: Figure 4.41 illustrates the problem. The points (vi, i1) and (v2, i2) are sufficient to define the straight-line iv (terminal) characteristic, which has the form i¼
v vT þ ; RT RT
(4.28)
where 1/RT is the slope and vT/RT is the (current) intercept. From Fig. 4.41,
v RT
1 i2 i1 v2 v1 ¼ ) RT ¼ : (4.29) i2 i 1 RT v2 v1
Using this result and the pair (v1, i1) in (4.28) gives 0 0
voc
v
Fig. 4.39 Terminal characteristic for a The´venin or Norton equivalent (for a two-terminal resistive circuit)
vT ¼ i1 m v1 ) vT ¼ i1 RT þ v1 : RT
(4.30)
4.4 The´venin and Norton Equivalent Circuits
99 i
voc
RT + –
Fig. 4.40 The´venin and Norton equivalent circuits if the open-circuit voltage and short-circuit current are negative
vT
0, 0
v
RN
iN
isc Thevenin equivalent
Norton equivalent
terminal characteristic
i
i0
R
a i1
v0
+ –
2R R
i2
R b
v1
v2
v
Fig. 4.42 See Example 4.14
Fig. 4.41 See Example 4.13
Exercise 4.9. A resistor R1 is connected to terminals a–b of a resistive circuit, and the resulting current out of terminal a is found to be i1. Then R1 is removed and another resistor R2 is connected to the terminals. The voltage vab across the second resistor is found to be v2. Obtain the The´venin equivalent for the resistive circuit at terminals a–b in terms of R1, R2, i1, and v2. We can find the The´venin or Norton equivalent resistance of a resistive circuit using the so-called look-back method, as follows:3 • Replace all independent voltage sources by short circuits (because the internal resistance of an independent voltage source equals zero). • Replace all independent current sources by open circuits (because the internal conductance of an independent current source equals zero). • Find the equivalent resistance at the terminals of interest.
3
In Chapter 6, we introduce sources called dependent sources. In general, the look-back method fails for circuits containing such sources.
Example 4.14. (Compare with Example 4.10.) Obtain an expression for the The´venin equivalent resistance at the terminals a–b of the circuit shown in Fig. 4.42. Solution: We replace the voltage source with a short circuit (a conductor) and replace the current source with an open circuit (remove the current source) to obtain the circuit shown in Fig. 4.43(a). We then use series/parallel reduction to obtain the The´venin (Norton) equivalent resistance, as shown in Fig. 4.43(b)–(d).
Exercise 4.10. Use the look-back method to determine the Norton equivalent resistance at the terminals a–b of the circuit shown in Fig. 4.44. Both the open-circuit voltage voc and the shortcircuit current isc equal zero for a circuit containing no sources. It follows that both the The´venin equivalent voltage vT ¼ voc and the Norton equivalent current iN ¼ isc for such a circuit equal zero. Consequently, we cannot use (4.20) to obtain the The´venin or Norton equivalent resistance for such a circuit because RT ¼ voc =isc is indeterminate. We point out this special case only for sake of completeness.
100
4 Equivalent Circuits R
a
a R 2
2R R
R
2R R b
b
(a)
(b)
a 5R 2
a 5R 7
R
b
2i0 R1
v0
+ –
2R2
i0
a
R2 b
Fig. 4.44 See Exercise 4.10
In practice, The´venin and Norton equivalents are not used to represent two-terminal circuits containing no sources. Such a circuit would instead be represented as an equivalent resistance, which can be found using methods described in Section 4.2 above. The´venin’s theorem is both plausible and remarkable. It is plausible because circuit-reduction and transformation methods described above allow us to reduce virtually any planar resistive circuit4 to a voltage source in series with a resistor. It is remarkable because it allows us to use a very simple model to describe even a very complex circuit (at a single terminal pair). Even more remarkable, The´venin’s theorem can be generalized to any circuit composed of any combination of sources, resistors, capacitors, and inductors, as described in subsequent chapters. We conclude this section with four remarks: • The terminal (i–v) characteristic for a The´venin or Norton equivalent circuit is independent of whatever is connected to the terminals of the circuit. The voltage across and current through the terminals are related by (4.16) no matter what. 4
b (d)
(c)
Fig. 4.43 See Example 4.14
A planar circuit is one that can be drawn in two dimensions without crossing conductors.
• The The´venin and Norton equivalents for a particular circuit at a particular terminal pair are unique. The The´venin equivalent source voltage, the Norton equivalent source current, and The´venin/Norton equivalent resistance can be found by any legitimate method. Nonetheless, you should regard the method based upon open-circuit voltage and short-circuit current as the fundamental (analytical) method for obtaining a The´venin or Norton equivalent. • A The´venin or Norton equivalent is only externally equivalent to the associated circuit. In general, the components of a The´venin or Norton equivalent are non-physical. They do not necessarily correspond to any physical components in an associated physical circuit. Thus, for example, the voltage across a The´venin resistance does not necessarily have any physical significance (is not necessarily measurable). • An independent voltage source does not possess a Norton equivalent (because the short-circuit current is undefined). Similarly, an independent current source does not possess a The´venin equivalent (because the open-circuit voltage is undefined). However, these limitations are of no practical significance.
4.5 Notation: Constant and TimeVarying Current and Voltage As we introduce more and increasingly complex devices and circuits, we need more suggestive notation to help us keep track of quantities and parameters
4.7 Problems
101
involved in analysis and design. In this section, we describe notational conventions for current and voltage and for parameters having dimensions of current or voltage. Notation introduced here is used throughout the remaining chapters of this book. During a time interval of interest, a current or voltage can be constant or time-varying. The almost universal convention is to use upper-case letters to denote constant currents or voltages and lower-case letters to denote time-varying currents or voltages. For example, V0 ¼ 15V and i1 ¼ 5 cosðo tÞ mA. We also use upper-case letters to denote a constant parameter having the dimension of a current or voltage, but which is not necessarily a current or voltage in a circuit under study (or in any other circuit). For example, we express a sinusoidally time-varying voltage as v1 ðtÞ ¼ V1 cosðo tÞ: The peak amplitude V1 is a constant parameter of the expression above for a sinusoidal voltage. If a current or voltage might be either constant or time-varying, e.g., where an analysis is valid for either case, the current or voltage is represented by a lower-case i or v. In this sense, i and v are more general than I and V; that is, a constant current or voltage is a special case of a time-dependent current or voltage.
4.6 Significance of Terminal Characteristics and Equivalence There are three important points to be made regarding terminal characteristics and equivalent circuits: • A circuit element is defined by its terminal characteristic. We do not need to know what is inside the element or how the element works to apply Kirchhoff’s laws to a circuit containing the element. • If two two-terminal elements or circuits have identical terminal characteristics, then they are equivalent at those terminals; that is, one can be replaced by the other at the terminals in question. This is the basis for the circuit-reduction methods described in Sections 4.2 and 4.3 and is a reason why The´venin’s theorem is so important. Keep in mind, however, that the equivalence is only at the terminals.
The internal structures of equivalent circuits are not necessarily (and usually are not) the same. In particular, we may use the The´venin or Norton equivalent for a circuit to study current through, voltage across, and power dissipated in a load attached to the circuit, but not to study any of those quantities internal to the circuit. • The task of studying the response of a circuit for various possible loads is greatly simplified by finding the The´venin (or Norton) equivalent for the circuit at the terminals to which the load is to be attached. If the load is resistive, the circuit and load are reduced to a voltage divider (or current divider), and further analysis is trivial.
4.7 Problems
Section 4.1 is prerequisite for the following problems. P 4.1 : In Fig. P 4.1, v1 ¼ 1.5 V, v2 ¼ 5 V, i1 ¼ 5 mA, i2 ¼ 10 mA, R1 ¼ 1 kO, and R2 ¼ 3:3 kO. (i) Obtain the terminal characteristic at the terminals a–b for each circuit, regarding the circuit as a source. (ii) Draw and label fully a graph of the terminal characteristic (current as a function of voltage). (iii) Assume a voltage source v0 ¼ 2 V is connected to the terminals a–b of each circuit, with the positive terminal at a. Find the resulting current exiting terminal a and use the graph obtained in part (ii) to illustrate the solution. (iv) Simulate the circuit and verify your answers. P 4.2 : Figure P 4.2 shows a generalized graph of the terminal characteristic at terminals a–b of each circuit in Fig. P 4.3, where each is regarded as a source. (i) Obtain expressions for the intercepts iSC, vOC in terms of circuit parameters. (ii) Let i0 ¼ 5 mA, v0 ¼ 1:5 V, R1 ¼ 1 kO, and R2 ¼ 3:3 kO. Calculate the values of the intercepts and simulate the circuit to verify the calculated values. P 4.3 : In Fig. P 4.4, v1 ¼ 1.5 V, i1 ¼ 1 mA, R1 ¼ 1:5 kO, and R2 ¼ 4 kO. (a) Obtain symbolic expressions for the terminal characteristics for the circuits at the labeled terminals. Treat the terminals a
102
4 Equivalent Circuits R1
v1 R1
+ –
iL
v2
vL
i1
R2
load
R2 iL
+ i1
+ + –
R1 a
R1
c
vL
load
–
b
–
v1
+ –
(b)
+ –
(a)
i2
R1 c
v1
R1
+ –
a R2
i1
+
vL
iL
load
v2 + –
+
+ –
ref
(e)
Fig. P 4.1 See Problem P 4.1
i iSC
o
vOC
load
vL –
R1
v
Fig. P 4.2 See Problem P 4.2
and c as positive. Treat the circuit on the left as a source and the circuit on the right as a load. (b) The circuits are connected: a to c and b to d. What is the resulting voltage vab? What is the resulting current i entering terminal c? (c) Plot the terminal characteristics obtained in Problem P 4.3 for each circuit on the same axes. (d) At what point (v, i) do the terminal characteristics intersect? Would this point be different if you treat the circuit on the left as a load and the circuit on the right as a source? (e) Simulate the circuit
ref (d)
R2
R2
–
d
iL
c
vL load
R2
(c)
v2
+
R1
R2
i1
–
R1
v1
c
iL
R1
c
R1
a
R1
R1
iL +
i1 load
+ –
v1
+ –
v1
vL –
b = ref (f)
and verify the calculated values of the terminal voltage and current. P 4.4 Imagine you are presented with a resistive circuit sealed in a box, but with access to a terminal pair. You have only a voltmeter and a few different resistors. Assume it is safe to connect any of the resistors to the terminal pair. What are the simplest (and fewest) measurements you would make to determine the terminal characteristic of the circuit at the accessible terminal pair? Justify your answer. P 4.5 : (a) Obtain an expression for the terminal characteristic at the terminals a–b of the circuit shown in Fig. P 4.5, regarding the circuit as a load. (b) The circuit is connected to the terminals of a source whose terminal characteristic is shown in Fig. P 4.6, with terminal a connected to terminal c. Obtain an expression for vab ¼ vcd in terms of i1, v1, and circuit parameters. (c) The connections are reversed, so that terminal a is connected to terminal d. Obtain an expression for vab ¼ vcd in terms of i1, v1, and circuit parameters. (d) Let v1 ¼ 10 V, i1 ¼ 8 mA, R1 ¼ 1 kO,
4.7 Problems
103 R1
R1
v0
R2 R2 + –
R1
v0
+ –
+ –
i0
v0
a
i0 b
a
+ –
v0
R2
R1 (b)
(c) + –
a
v0
R1 + –
v0
v0
R2
+ –
a
a + –
v0
i0
R2
b
R1
b
(a)
R1
R1
R1
a
i0
R1
i0
i0
R1
b
R1
R2 b + –
R1
v0
b
(d)
(e)
(f) a
i0 R1 + –
R2 R1 R2
i0 b
Fig. P 4.3 See Problem P 4.2, 47
R1
+ –
a
R2
i0
v0
v0
R2
R1
b
(g)
(h)
i
c
a
i
i1
v1 +–
R2
R2
R1
i1
d
b
Fig. P 4.4 See Problem P 4.3 o
v1
c + vcd − d
vcd
Fig. P 4.6 See Problem P 4.5
a + –
v0
b
a
+ –
R1
R2
R1
Fig. P 4.5 See Problem P 4.4
v0
R2
i0
b
R2 ¼ 2:2 kO and v0 ¼ 15 V. Calculate the values of the terminal voltages obtained in parts (b) and (c). (d) Use simulation to verify the results obtained in parts (b) and (c). P 4.6 : Repeat Problem P 4.5 for the circuit shown in Fig. P 4.7, with i0 ¼ 5 mA:
Fig. P 4.7 See Problem P 4.6
P 4.7 : Repeat Problem P 4.5 for the circuit shown in Fig. P 4.8, with i0 ¼ 5 mA, R0 ¼ 470 O, and v2 ¼ 12 V.
104
4 Equivalent Circuits i0 R1 R0
a
+ –
+ –
v0
R1
b
v2
Fig. P 4.8 See Problem P 4.7
a R1
R2
i0
R2
R1
b
Fig. P 4.9 See Problem P 4.8
P 4.8 : Repeat Problem P 4.5 for the circuit shown in Fig. P 4.9.
Section 4.2 is prerequisite for the following problems. P 4.9 Show that the tolerance of a series connection of two resistors is in general bounded by the tolerance of the least precise resistor. Do not assume the (nominal) resistances are equal. P 4.10 Repeat Problem P 4.9 for a parallel connection of two resistors. P 4.11 A 470 O 5% resistor is connected in series with a 121 kO 1% resistor. Give the nominal resistance and the tolerance of the series connection. P 4.12 A 470 O 5% resistor is connected in parallel with a 121 kO 1%. Give the nominal resistance and the tolerance of the parallel connection. P 4.13 The tolerance of a parallel connection of two resistors R1, R2 must be 2% or better. What tolerance is required of each resistor? P 4.14 A trimmer resistor is in series with a 91 kO 5% fixed resistor. The range of the trimmer
must be such that the total (series) resistance can be set to 100 kO. What is the required resistance of the trimmer? P 4.15 Two resistors having 25 C resistances R1, R2 and 25 C temperature coefficients a1, a2 are connected in series. (a) Obtain an expression for the 25 C temperature coefficient of the equivalent resistance. (It is a function of the individual nominal resistances and temperature coefficients.) (b) What is the temperature coefficient if the two resistors have equal nominal resistances and temperature coefficients? (c) If they have equal temperature coefficients but different nominal resistances? (d) Equal nominal resistances but different temperature coefficients? P 4.16 Two resistors having 25 C resistances R1 ¼ 1 kO, R2 ¼ 2:2 kO and 25 C temperature coefficients a1 ¼ 0:001 K1 , and a2 ¼ 0:0005 K1 are connected in series. (a) Obtain a symbolic expression for the equivalent resistance as a function of the temperature difference DT ¼ T T0 , where T0 ¼ 25 C. (b) Calculate the equivalent resistance for T ¼ 50 C and T ¼ 100 C, and use the two data points to obtain a linear (straight-line) approximation to the equivalent resistance as a function of temperature. (c) What is the theoretical error in the linear expression obtained in Part (b)? Calculate the actual error at the endpoints of the range 50 C T 100 C. P 4.17 : Two resistors having 25 C resistances R1 ¼ 100 kO; R2 ¼ 220 kO and 25 C temperature coefficients a1 ¼ 0:003 K1 ; a2 ¼ 0:004 K1 are connected in parallel. (a) Obtain a symbolic expression for the equivalent resistance as a function of the temperature difference DT ¼ T T0 , where T0 ¼ 25 C. (b) Calculate the equivalent resistance for T ¼ 50 C and T ¼ 100 C, and use the two data points to obtain a linear (straight-line) approximation to the equivalent resistance as a function of temperature. (c) Construct graphs of the true equivalent resistance and the linear approximation on the same axes, for 50 C T 100 C. (d) Calculate and plot (on another pair of axes) the percent error in the approximation over the same range. P 4.18 Obtain an expression for the equivalent resistance at the terminals a–b for each circuit shown in Fig. P 4.10. P 4.19 Obtain expressions for the resistors R1, R2, R3 in terms of Ra, Rb, Rc such that the circuits in Fig. P 4.11 are equivalent at each pair of terminals (w–x, y–z, w–y).
4.7 Problems
105
4R
3R
4R
2R
R
2R
R R a
a
R
a
2R
R
R
b
R
4R
2R b
R
(a)
b
(b)
(c)
4R a
2R
b
2R
R
R
3R
R
R
2R
R
4R
a R
R
3R R
a
2R 4R
2R
2R
b
b
(e)
(d)
a
2R 3R
2R
2R
4R
4R
a
(f) R
R R
R R
R
b 2R
R
b
Fig. P 4.10 See Problem P 4.18
w
R1
R2
(g)
y
Rc
w
R3
Ra
x
10 identical sections (20 resistors, total)
a
y
a
R1
Rb
x
z
(h)
i0 b
i0
z
R1 b
R2
Fig. P 4.11 See Problem P 4.19, 20
R2
i0
c R1
R1
a R2
b
b
v0
a
R
c b
2R
R
v0
4R
i0
2i0
4R
+ –
Fig. P 4.12 See Problem P 4.21
v0 + –
c
Fig. P 4.13 See Problem P 4.22
R2
+ – + –
v0 + –
v0
a
c
Fig. P 4.14 See Problem P 4.23
P 4.20 Obtain expressions for the resistors Ra, Rb, Rc in terms of R1, R2, R3, such that the circuits of Fig. P 4.11 are equivalent at each pair of terminals (w–x, y–z, w–y). P 4.21 Show that the circuits shown in Fig. P 4.12 are equivalent at each of the three possible terminal pairs. P 4.22. Show that the circuits shown in Fig. P 4.13 are equivalent at each of the three possible terminal pairs.
Section 4.3 is prerequisite for the following problems. P 4.23 : See Fig. P 4.14. (a) Use source transformations to obtain a circuit consisting of a voltage source in series with a resistance that is equivalent to
106
4 Equivalent Circuits
the original circuit at the terminals a–b. Express the source voltage and series resistance as functions of the original circuit parameters. (b) Let i0 ¼ 5 mA, v0 ¼ 10 V, and R ¼ 1 kO. Construct a graph of the terminal characteristic for the reduced equivalent circuit, regarding the circuit as a source. (c) Simulate the equivalent circuit with a load RL ¼ 2:2 kO attached to the terminals a–b and verify that the load current and load voltage are consistent with the terminal characteristic obtained above. (d) Simulate the original circuit using the same load and verify that the load current and load voltage equal those obtained in part (c) (from the equivalent circuit). P 4.24 : Repeat Problem P 4.23 for the circuit shown in Fig. P 4.15. P 4.25 : Repeat Problem P 4.23 for the circuit shown in Fig. P 4.16. P 4.26 : Repeat Problem P 4.23 for the circuit shown in Fig. P 4.17.
i0 a 2i0
2R
R
R + –
2R 2R
v0
b
P 4.27 Repeat Problem P 4.23 for the circuit shown in Fig. P 4.18. P 4.28 Repeat Problem P 4.23 for the circuit shown in Fig. P 4.19. P 4.29 For each circuit of Fig. P 4.20, use source transformations to obtain an expression for the voltage vx. Check your answers using node or mesh analysis.
Section 4.4 is prerequisite for the following problems. P 4.30 : In Fig. P 4.21, v0 ¼ 5V, v1 ¼ 10V, i0 ¼ 5mA, i1 ¼ 10 mA, R0 ¼ 1 kO, and R1 ¼ 2:2 kO. (a) Use simulation to obtain the open-circuit voltage and short-circuit current at the terminals a–b. (b) Simulate the original circuit, the The´venin equivalent, and the Norton equivalent with a load RL ¼ 2:7 kO attached to the terminals a–b and show that the load current (or voltage) is the same for all three cases (allowing for small computational errors). P 4.31 : See Fig. P 4.22, where i0 ¼ 5mA, v0 ¼ 10V, R0 ¼ 1 kO, and R2 ¼ 1:5 kO. (a) Use simulation to obtain the The´venin equivalent for the source at the terminals to which the load is connected. (b) Draw a graph of the terminal characteristic for the source. (c) Use the The´venin equivalent with the load attached and plot the load current iL as a function of the load resistance RL, for 0 O RL 10 kO.
Fig. P 4.15 See Problem P 4.24 R
4R
v0
+ –
i0
2R
R
v0
4R
R
a
i0 + –
a
2R
+ –
4R
2R
4R
R R
v0
b
b
Fig. P 4.18 See Problem P 4.27 Fig. P 4.16 See Problem P 4.25 4R
a
4R R
R
i0
a
R
2R
R
b
i0 R
v0 + –
Fig. P 4.17 See Problem P 4.26
R b
R
+ –
v0
Fig. P 4.19 See Problem P 4.28
2R
2R
4.7 Problems
107
+ –
+ vx – R0
i0
R1
+ –
v0
i1
+ –
vx
R0
R1
v0
+ + –
v1
v1
2R0
i0
R0
(b)
– (a)
R0
v1
R0
R0
2R0
i0 R0
v0
i1
R1
R1
+ –
+ –
i0
+
+ + –
v0
i0
R0
vx
R1
–
–
Fig. P 4.20 See Problem P 4.29
(d)
(c)
R0
R0
+ –
i1
v0
R1
v0
+ –
+ –
a
a
a
v0
vx
2R0
2v1
+ –
R0
v1
i0
i0
2R0
b
(a)
R1
R0
R0
(b)
R1
R1
+ –
i1
v0 v1 + –
b
i1
b
R0 R1
R1
(e)
b
(f)
v0 R0 iL
R1
3R0
i0 R1
RL
source
load
2i0
v0
load
(b)
+ –
iL RL
i0
iL RL
R0
+ –
source
(a)
Fig. P 4.22 See Problem P 4.31
v0
R1
(d)
+ –
R0 + –
Fig. P 4.21 See Problem P 4.30
a
i1
a R0 R1
2R1
b
R0
R0
v1
(c) a
v1 R0 v + 0 –
+ –
v1
b
i0 + –
+ –
+ –
R1
load
R1 i0
source (c)
v0
+ –
+ –
R0
v0
R1
v0
R0 i0
source
R1
iL RL load
(d)
108
4 Equivalent Circuits 5
i0
R0 + –
v0
R1
4
iL R0 R0
R0 R1
v1
+ –
3 V (V) 2
source
load 1
Fig. P 4.23 See Problem P 4.32
0
0
1
iL + –
R0
v0
R0 i0
R1
source
R1
i0
2
3
4 5 6 I (mA)
7
8
9
10
Fig. P 4.25 See Problem P 4.34
load
Fig. P 4.24 See Problem P 4.33
P 4.32 In Fig. P 4.23, i0 ¼ 5mA, v0 ¼ 10V, v1 ¼ 12V, R0 ¼ 1 kO, and R1 ¼ 2:2 kO. (a) Use a method of your choice to obtain the terminal characteristics of the source and load. (b) Plot the terminal characteristics of the source and load on the same axes, and find (graphically) the load current iL that results when the source and load are connected. (c) Using a method of your choice, but different from that used in part (a), find the load current iL when the load is connected to the source. Compare the result with that obtained in part (b) and explain any differences. P 4.33 Repeat Problem P 4.32 for the source and load shown in Fig. P 4.24. P 4.34. Measurements of voltage and current are made at terminals a–b of a resistive circuit for three different resistive loads. Figure P 4.25 shows a graph of the measured values. Find the The´venin and Norton equivalents for the circuit at the terminals a–b. P 4.35. Figure P 4.26 shows the terminal characteristic for a certain two-terminal circuit. The positive direction for the terminal current is out of the positive terminal of the circuit. (a) Find the The´venin and Norton equivalents for the circuit. (b) A 400 O resistor is connected to the terminals of the circuit. Find the voltage across and current through the resistor. (c) The 400 O resistor is removed and a 15V independent source is connected to the terminals of the
i (mA) 60
v (V)
0 0
12
Fig. P 4.26 See Problem P 4.35
i (mA) −100
(0, 0)
v (V)
−50
Fig. P 4.27 See Problem P 4.36
circuit, with the positive terminal of the source connected to the positive terminal of the circuit. Find the current out of the positive terminal of the 15 V source. P 4.36 Repeat Problem P 4.35 for the graph in Fig. P 4.27. P 4.37 Use a method specified by your instructor to find the The´venin and Norton equivalent circuits at the terminals a–b for each circuit in Fig. P 4.28, where i0 ¼ 5mA, v0 ¼ 5V, and R ¼ 1kO.
4.7 Problems
109 R a
i0
R
2i0
2R
+ –
R a
b
(b) 4R
R
R 4R
v0
2R
+ –
v0
a
+ –
v0
R
a
+ –
2R
4R
2v 0
(d) R
4R
a
b
b
4R
+ –
4R
(c)
i0
2R
a
i0
+ –
v0
b
(a) 4R
v0
+ –
v0
+ –
R
v0
R
i0
b R
b (e)
(f ) i0
2R
b + –
R
2R
v0
R
i0
b
a
i0
R R
R R
2R
i0
a
(g)
(h)
R
v0
+ –
b
i0
R
a
R
+ –
i0
v0
R + –
v0
+ –
v0
+ –
R
a
v0 b
Fig. P 4.28 See Problem P 4.37
2R
2R
(i)
P 4.38 N identical Norton source models are connected in series, as in Fig. P 4.29. Find the (single) Norton equivalent at the terminals a–b. P 4.39 N identical The´venin source models are connected in parallel, as in Fig. P 4.30. Find the (single) The´venin equivalent at the terminals a–b. P 4.40 Refer to Fig. P 4.31, where the resistance R is known and fixed and the voltage v0 is variable. It is found that for v0 ¼ v1, vR ¼ va and that for v0 ¼ v2, vR ¼ vb. Obtain an expression for the voltage vR as a function of the voltage v0 and in terms of the known quantities v1, v2, va, vb, R.
( j)
R
R
R
I
I
I
b
a
N identical sections
Fig. P 4.29 See Problem P 4.38
P 4.41 Refer to Fig. P 4.31, where the voltage v0 is known and fixed and the resistance R is variable. It is found that for R ¼ R1, vR ¼ va and that for R ¼ R2, vR ¼ vb. Obtain an expression for the voltage vR as a
110
4 Equivalent Circuits a R
R
R
V +–
V +–
V +–
source 1
b
+
N identical sections
source 2
RL
VL –
Fig. P 4.30 See Problem P 4.39 Fig. P 4.34 See Problem P 4.45, 46 R +
v0
+ –
vR
–
resistive circuit
v0
+ –
+
R i0
10R
v –
Fig. P 4.31 See Problem P 4.40, 41 a
c
b
d
e
f
Fig. P 4.35 See Problem P 4.48
Fig. P 4.32 See Problem P 4.42
a
1
Fig. P 4.33 See Problem P 4.43, 44
linear resistive circuit
b
2
function of the resistance R and in terms of the known quantities R1, R2, va, vb, v0. P 4.42 Refer to Fig. P 4.32. Let vT1 ; RT1 and vT2 ; RT2 denote the The´venin voltage and resistance at the terminals a–b and c–d, respectively, where a and c are the positive terminals. Find the The´venin equivalent at the terminals e–f. P 4.43 Refer to Fig. P 4.33, where the boxes enclose resistive circuits. Let vT1 ; RT1 and vT2 ; RT2 denote the The´venin voltage and resistance at the terminals a–b for circuits 1 and 2, respectively, where a is the positive terminal. Obtain expressions for the The´venin equivalent voltage and resistance at the terminals a–b in terms of vT1 ; RT1 and vT2 ; RT2 .
P 4.44 Refer to Fig. P 4.33, where the boxes enclose resistive circuits. Let vT1 ; RT1 denote the The´venin voltage and resistance for circuit 1. Let iN ; RN denote the Norton current and resistance at the terminals a–b. Obtain expressions for the The´venin equivalent voltage and resistance for circuit 2 in terms of vT1 ; RT1 and iN ; RN . P 4.45 Two sources having the same open-circuit voltage VOC ¼ 10 V are connected in series, and then to a load RL ¼ 200 O, as shown in Fig. P 4.34. It is found that VL ¼ 5 V. Obtain the The´venin equivalent for the series connection of the sources. P 4.46 Two sources having the same short-circuit current ISC ¼ 100 mA are connected in series, and then to a load RL ¼ 500 O, as shown in Fig. P 4.34. It is found that VL ¼ 15 V. Obtain the The´venin equivalent for the parallel connection of the sources. P 4.47 In essence, Problem P 4.2 asks for the terminal characteristics of the circuits in Fig. P 4.3, treating the circuits as sources. Using results of that problem, obtain the terminal characteristic at a–b for each circuit, treating each as a load. P 4.48 Refer to Fig. P 4.35, where R ¼ 2 O and the sources v0 ; i0 are independently variable. It is found that for v0 ¼ 10V and i0 ¼ 2A, the voltage v ¼ 12V, and that for v0 ¼ 20V and i0 ¼ 6A, the voltage v ¼ 24V. Find the voltage v if v0 ¼ 30V and i0 ¼ 10A. P 4.49 : Refer to Fig. P 4.36, where the boxes enclose resistive circuits. The The´venin voltage and
4.7 Problems
111
resistance, respectively, at the terminals a–b for the circuit in box 1 are vT1 ¼ 5V; RT1 ¼ 2kO, where a is the positive terminal. A known resistance R is connected as shown, and the voltage v is measured. It is found that for R ¼ 1 kO; v ¼ 1:143V and that for R ¼ 2 kO; v ¼ 1:600 V. Find the The´venin equivalent for the circuit in box 2. Use simulation to verify your answer. P 4.50 A current source i0 ¼ 5 mA is connected to terminals a–b of a resistive circuit, with the positive direction of current into terminal a. It is found that vab ¼ 10V. Then the current source is removed and it is found that vab ¼ 5V. Find the The´venin equivalent for the circuit at the terminals a–b. P 4.51 A voltage source v0 ¼ 5V is connected to terminals a–b of a resistive circuit, with the positive terminal connected to circuit terminal a. It is found that the current into the positive terminal of the source is i ¼ 10 mA. Then the voltage source is removed, a 2 kO resistor is connected to the terminals a–b, and the voltage across the resistor is found to be 2 V. Find the The´venin equivalent for the circuit at the terminals a–b. P 4.52 A current source i0 ¼ 5mA is connected to terminals a–b of a resistive circuit, with the positive direction of current into terminal a. It is found that vab ¼ 10V. Then a 2 kO resistor is connected in paral-
+
1
a b
2
v
R
–
Fig. P 4.36 See Problem P 4.49
lel with the current source and it is found that vab ¼ 5V. Find the The´venin equivalent for the circuit at the terminals a–b. P 4.53 : A voltage source v0 ¼ 5V is connected to terminals a–b of a resistive circuit, with the positive terminal connected to circuit terminal a. It is found that the current into the positive terminal of the source is i ¼ 10 mA. Then a 2 kO resistor is connected in series with the voltage source, the series connection is connected to the terminals a–b, and it is found that vab ¼ 2 V. Find the The´venin equivalent for the circuit at the terminals a–b. Use simulation to verify your answer. P 4.54 A variable resistor is connected to terminals a–b of a resistive circuit. Neither terminal is directly connected (inside the circuit) to an independent source. Does the current through the resistor increase or decrease as the resistance is decreased? Use The´venin’s theorem to justify your answer. P 4.55 A variable resistor is connected to a terminal pair of a resistive circuit, as shown in Fig. P 4.37. The current through the resistor is measured and plotted versus the resistance R. The resulting plot also is shown in Fig. P 4.37. Find the Norton equivalent for the circuit at the terminals a–b. P 4.56 A voltage source is connected to theterminals of a resistive circuit, as shown in Fig. P 4.38. The The´venin voltage and resistance for the circuit are vT ¼ 20V and RT ¼ 10 kO, respectively. Construct a graph of the current i through the source versus the source voltage v0 for 10V v0 30V. Show how you would obtain the The´venin equivalent for the circuit from the graph if vT and RT were unknown. P 4.57 Refer to Fig. P 4.39. The circuits enclosed in the boxes are resistive and are equivalent at the 6 5
a
i 4
resistive circuit
R b
i (mA) 3 2 1
Fig. P 4.37 See Problem P 4.55
0
5
10 R (kΩ)
15
20
112
4 Equivalent Circuits i
+ + –
resistive circuit
+
v0
V0
Rl
Rs
–
−
battery
Fig. P 4.38 See Problem P 4.56 Fig. P 4.41 See Problem P 4.62
a
i
+
+
v
1
2
–
V0
+
Rs
Rl
–
b
battery
−
Fig. P 4.39 See Problem P 4.57 Fig. P 4.42 See Problem P 4.64
R1 B R2
RC
+
C
–
VCC
E
Fig. P 4.40 See Problem P 4.58
terminals a–b, each having open-circuit voltage vOC ¼ 50 mV. Find the voltage v and the current i. P 4.58 Refer to Fig. P 4.40. Find the The´venin equivalent circuit at (a) the terminals C–E and (b) the terminals B–E. (c) Draw graphs of the two terminal characteristics. P 4.59 Suppose we agree that a source represented by a The´venin equivalent can be considered a good voltage source if the load voltage varies by no more than 1% (of the The´venin voltage) over the range of expected values of load resistance. If a certain source model has The´venin resistance RT ¼ 1O, for what values of load resistance can the source be considered a good voltage source? P 4.60 Suppose we agree that a source represented by a Norton equivalent can be considered a good current source if the load current varies by no more than 1% (of the Norton current) over the range of expected values of load resistance. If a certain source model has Norton resistance RN ¼ 10 kO, for what
values of load resistance can the source be considered a good current source? P 4.61 Imagine you are presented with a resistive circuit sealed in a box, but with access to a terminal pair. You also have access to a full complement of laboratory instruments. Describe fully all of the methods you can think of for finding the The´venin equivalent for the circuit at the exposed terminals. P 4.62 An automotive lead-acid battery can be modeled as shown in Fig. P 4.41. The leakage resistance R‘ accounts for the fact that the battery will eventually self-discharge, even if not connected to a load. The series resistance Rs accounts (approximately) for the fact that the terminal voltage decreases as load current increases. Obtain the Norton equivalent for the battery at the terminals. What happened to the leakage resistance? In what sense is the Norton model equivalent to the battery? P 4.63 Repeat Problem P 4.62 using a The´venin equivalent for the battery. P 4.64 Figure P 4.42 shows another model for the battery described in Problem P 4.62. (a) Obtain the Norton equivalent for this model. (b) Obtain the The´venin equivalent for this model. (c) What kinds of studies cannot be performed using the The´venin or Norton models for the battery? What kinds can be performed? (d) Under what condition are the models in Figs. P 4.42 and P 4.41 equivalent at their terminals?
Chapter 5
Work and Power
Work is an amount of energy converted from one form to another and power is the rate of such conversion. The instantaneous power p(t) corresponding to instantaneous work w(t) is given by p¼
dw : dt
(5.1)
Brightness of a light bulb or computer display, loudness of music from a loudspeaker, and time required for a pump to drain a flooded basement all depend upon rate of energy conversion. Consequently, electrical engineers usually are more interested in the rate at which work is done (power) than work itself. Exceptions are design of storage batteries, where energy stored per unit volume and per unit mass are prime concerns, and in management of electric-utility companies, which sell energy. But even in those cases, engineers are interested in the rate at which stored energy can be drawn from a battery and the rate at which energy can be delivered to a customer. Power is of concern in circuit analysis and design for various reasons, including: • An electric circuit must do work at a specified rate on a load, such as a light bulb, a loudspeaker, a transmitting antenna, or an electric motor. Each component of the circuit must be capable of doing the work required of the component at the specified rate. • The power supply for a circuit must be able to provide energy to the circuit at a rate sufficient to support operation of the circuit. That is, the power supply must be able to provide power equal to or greater than the total power dissipated (converted to another form) by the circuit.
• Work done on circuit components generates heat, which must be removed quickly enough to keep the temperatures of the components from rising above acceptable values. The temperature of a dissipative device will rise until the rate at which heat is removed equals the rate at which the heat is produced. This equilibrium condition must be reached at a temperature the device can endure. As a rule, the lifetime of a device decreases as the equilibrium operating temperature increases. Also, because resistivity generally increases with increasing temperature, performance usually decreases with increasing temperature. Consequently, it usually is desirable to keep the equilibrium temperature of a device below the maximum permissible value. • Most circuit components, as a by-product of normal operation, generate electrical noise (e.g., thermal noise in resistors) that contaminates other voltages and currents of interest. Electrical noise produced by most components increases with increasing temperature, which, in turn, usually increases with the rate at which work is done on or by the component. • Many circuits are described at least in part by power gain (or loss), which is the ratio of the power delivered by a circuit to a load to the power provided to the circuit by a source. Power gain (or loss) is an especially important parameter in communication systems. In electrical engineering, there is a rich vocabulary associated with work and power. Practicing engineers refer to power being absorbed, consumed, dissipated, generated, produced, delivered, transmitted or distributed. Strictly speaking, it is energy, not power, that is absorbed, generated, distributed, or the like. Instantaneous power is the rate at which energy is being
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_5, # Springer Science+Business Media B.V. 2011
113
114
5 Work and Power
converted or transmitted at a particular time and place. Power does not go anywhere and power is not generated or dissipated. Nonetheless, practicing engineers understand what is meant by such terminology, and the terminology is useful because it makes descriptions and discussions much more compact than they would be otherwise. In this chapter, we obtain expressions for electrical work and power as functions of voltage, current, and circuit parameters.
5.1 Instantaneous Power and the Passive Sign Convention Instantaneous power, denoted by p, is the instantaneous rate at which energy is converted from one form to another. Equivalently, instantaneous power is the rate at which the associated work is done. Instantaneous power corresponding to instantaneous work w is given by (5.1), repeated below for ready reference. p¼
dw : dt
(5.2)
The SI unit of power is the watt (W), where 1 W ¼ 1 J s1 . Instantaneous power is (in general) a function of time. We are interested in work and power in the context of circuit analysis, so we wish to express instantaneous power in terms of voltage and current. Because voltage is work done (on an electric field) by a charge per unit charge, we may write
power p given by (5.5) is called the instantaneous power dissipated by the device or circuit (at the terminal pair in question). Above, we define positive work as work done by a charge dq. Because energy is conserved, we could as well define positive work as work done on the charge, but defining positive work as work done by the charge is consistent with the passive sign convention used in almost all circuits textbooks, according to which power is positive if the positive direction of current in (5.5) is in the direction of a voltage drop; i.e., into the positive terminal of a device or circuit element under consideration. Thus positive power means that positive work is being done by the current (the device or circuit is consuming energy) and negative power means that work is being done on the current (the device or circuit is producing energy). Figure 5.1 illustrates the definition of power dissipated according to the passive sign convention. Generally, we follow the passive sign convention, to the extent that power dissipated by an element, device, or circuit means power dissipated in accord with the passive sign convention. But in many cases, it is more convenient (and meaningful) to refer to power delivered by an element, device, or circuit, where power delivered is the negative of that determined using the passive sign convention. Specifically, for a resistor, we almost always compute power dissipated (consumed), but for a source, we frequently compute power delivered to a load. For example, for the circuit shown in Fig. 5.2, the instantaneous power dissipated
i
v¼
dw ; dq
(5.3)
+ v
where dq is a small quantity of positive charge and dw is the work done by the charge. It follows that dw ¼ v dq:
(5.4)
Using the right side of (5.4) for dw in (5.2) gives p¼v
dq ¼ v i: dt
i + p = vi
–
p = –vi
v
–
Fig. 5.1 Passive sign convention: The instantaneous power dissipated at a terminal pair is the product of the instantaneous voltage across the terminals and the instantaneous current into the positive terminal
(5.5)
In (5.5), v and i denote voltage across and current through a terminal pair of a device or circuit. The
i
Fig. 5.2 Power delivered by the source is dissipated by the resistor (see text)
+ v –
R
5.1 Instantaneous Power and the Passive Sign Convention
by the resistor and the power delivered by the source are both given by p ¼ v i, where the positive direction for current is out of the positive terminal of the source and into the positive terminal of the resistor.
115 + + vi
i0
vR R
– v0 +–
i0 = I0 cos(w 0 t) v0 = V0 cos (w 0 t)
–
Fig. 5.3 See Example 5.2
Example 5.1. The voltage across a certain electrical device and the current entering the positive terminal of the device are given by vðtÞ ¼ V0 cosðo tÞ; iðtÞ ¼ I0 cosðo tÞ; respectively. Obtain an expression for the instantaneous power dissipated by the device. Solution: The positive direction for current is consistent with the passive sign convention. From (5.5), the instantaneous power dissipated is given by V0 I0 ½1 þ cosð2 o tÞ; p ¼ v i ¼ V0 I0 cos2 ðo tÞ ¼ 2 where we have used the identity cos2 ðaÞ
1 ½1 þ cosð2 aÞ: 2
Exercise 5.1. The voltage across a certain electrical device and the current entering the positive terminal of the device are given by vðtÞ ¼ V0 cosðo tÞ; iðtÞ ¼ I0 cosðo t þ yÞ; respectively. Show that the instantaneous power dissipated by the device is given by pðtÞ ¼
V0 I0 ½cosðyÞ þ cosð2o t þ yÞ: 2
Example 5.2. Obtain expressions for the instantaneous power dissipated by each component in the circuit shown in Fig. 5.3, where I0 > 0 and V0 > 0. Is the current source producing energy or consuming energy? Is the voltage source producing energy or consuming energy?
Solution: From (5.5) and Ohm’s law, the instantaneous power dissipated by the resistor is given by pR ¼ vR i0 ¼ ði0 RÞ i0 ¼ R i0 2 ¼ R I0 2 cos2 ðo0 tÞ and is independent of the source voltage v0. The power dissipated by the voltage source is given by pv ¼ i 0 v0 ¼ I0 V0 cos2 ðo tÞ: Because the positive direction for the current i0 is into the positive terminal of the voltage source. The power dissipated by the current source is given by pi ¼ i0 vi because the positive direction for the current i0 is out of the positive terminal of the current source. Kirchhoff’s voltage law gives vi þ vR þ v0 ¼ 0 ) vi ¼ vR þ v0 ¼ i0 R þ v0 ¼ ðI0 R þ V0 Þ cosðo tÞ: Thus the power dissipated by the current source is given by pi ¼ i0 vi ¼ I0 ðI0 R þ V0 Þ cos2 ðo tÞ: Because the quantities R; I0 ; V0 ; and cos2 ðo tÞ are all positive, the power dissipated by the current source is negative and the power dissipated by the voltage source is positive. It follows that the current source is producing energy, whereas the voltage source is consuming energy.
Exercise 5.2. Obtain expressions for the instantaneous power dissipated by each component in the circuit shown in Fig. 5.4, where
116
5 Work and Power
v1
R + –
v0
i0
2R
i0 = I0 cos (w 0 t) v0 =V0 cos (w 0 t)
Fig. 5.4 See Exercise 5.2
I0 > 0 and V0 > 0. Is the current source producing energy or consuming energy? Show that the powers dissipated by the resistors are positive. Is the voltage source producing energy or consuming energy? Examples and exercises above illustrate the fact that a current or voltage source in a circuit containing two or more sources can either dissipate or deliver power, depending upon the configuration of the circuit.1 As a physical example, a battery connected to a light bulb delivers power to the bulb (the battery produces energy), whereas a battery connected to a battery charger receives energy from the charger (the battery consumes energy). The examples and exercises also illustrate the fact that the power dissipated by a physical resistor is always positive. If you obtain a negative value for the power dissipated by a physical resistor, you have made an error.2 According to the passive sign convention, power at the terminals of an electric heater, for example, is positive, whereas power at the terminals of an electric generator is negative. In practice, despite preferences of textbook authors, what is meant by positive power usually depends upon circumstances. In describing an electric heater, which converts electrical energy to heat energy, one might define positive power as the rate at which work is done on the heating element, which is consistent with the passive sign convention. On the other hand, in describing an electric generator, we are interested in the rate at which the generator can convert mechanical energy to electrical energy, and we might define positive power in opposition to the
passive sign convention. No manufacturer of electric generators would advertise a “5 kW generator.” Nonetheless, if applied consistently and interpreted correctly, the passive sign convention facilitates analysis. We do not need to determine whether an element is consuming or generating energy before choosing reference directions for voltage and current. We simply assign directions to currents and polarities to voltages and then use the passive sign convention (Fig. 5.1) for power calculations; that is, we use p ¼ v i if the positive direction for current is into the positive terminal of a device, and p ¼ v i if the positive direction for current is out of the positive terminal of a device. If the power thus obtained is positive, then electrical energy is being converted to some other form (the device dissipates power). If the power turns out to be negative, then some other form of energy is being converted to electrical energy (the device generates power).
5.2 Instantaneous Power Dissipated by a Resistor: Joule’s Law Using Ohm’s law v ¼ R i in (5.5) shows that instantaneous power dissipated by a resistor is given by p ¼ v i ¼ R i2 ¼
v2 : R
(5.6)
Because (physical) resistance is non-negative, the instantaneous power dissipated by a physical resistor is non-negative and equals zero only if the current through or voltage across the resistor equals zero.3 Equation (5.6) is essentially an expression of Joule’s law. Integrating (5.6) over an interval t1 t < t2 gives the total work done on a resistor in the interval: w¼
ð t2 t1
pðtÞ dt ¼ R
ð t2 t1
i2 ðtÞdt ¼
1 R
ð t2
v2 ðtÞ dt: (5.7)
t1
Electrical energy delivered to a resistor is converted to heat or other radiant energy (as by a light bulb). 1
Also, a source can dissipate power during some time intervals and deliver power during others. 2 Using electronic devices, it is possible to construct a twoterminal circuit that has the properties of a negative resistance; however, such a circuit is not a physical resistor.
3
Certain two-terminal circuits are equivalent to a negative resistance at their terminals.
5.2 Instantaneous Power Dissipated by a Resistor: Joule’s Law
117
The radiant energy produced in an interval t1 t < t2 is given by (5.7). The instantaneous rate at which the radiant energy is produced is given by (5.6).
of power-transmission lines can be significant. But dissipation of electric power as heat or other radiant energy also can be useful. Everyday examples include light bulbs, electric ovens, electric heaters, electric ranges, and electric water heaters. Moreover, even a power company finds the resistance of its lines useful during winter, when heat caused by current in the lines can melt ice that otherwise might accumulate and break the lines. Virtually all circuit components, and resistors in particular, generate heat while operating, which is why a television receiver, for example, is warmer when on than when off. Some devices become hot enough to burn skin when operating normally. But there are limits to the temperatures that resistors, transistors, and other electrical devices can endure and still operate as intended; for example, a typical off-the-shelf discrete bipolar junction transistor will operate normally at temperatures below about 75 C ¼ 167 F. Bipolar transistors built to military specifications (mil-spec devices) will operate normally at somewhat higher temperatures, up to about 125 C ¼ 257 F. Typically, circuits are designed such that components operate below the maximum permissible temperatures because operation at higher temperatures shortens component lifetime, affects cooling requirements, increases electrical noise produced by components, and increases the resistance of (and power losses in) conductors and resistors. Ability of a component to operate at a safe temperature in ambient air depends upon the size, composition, and surface area of the component; e.g., a ½ W resistor is larger than a ¼ W resistor of the same kind. Barring catastrophic failure, the temperature of a device rises until an equilibrium temperature is reached, at which point the power dissipated as heat equals the rate at which heat is removed from the device. A sustained temperature above the maximum temperature a device can endure will damage the device or at least cause permanent changes to properties of the device. Most devices are rated, based upon maximum permissible temperature, in terms of the average power that can be dissipated in ambient air (in absence of heat sinks and forced cooling)4 without damage; for example, a ½ W resistor can dissipate ½ W in ambient air without harm, but if called upon
Example 5.3. The voltage across a resistor having resistance R ¼ 1 kO is V ¼ 10 V. Calculate the instantaneous power dissipated by the resistor, the current through the resistor, and the total work done on the resistor in 1 s. Solution: From (5.6), the power dissipated is p¼
V 2 ð10 VÞ2 ¼ ¼ 0:100 W ¼ 100 mW: R 103 O
Because p ¼ i2 R, the current is rffiffiffi rffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi p 0:100 W ¼ I¼ ¼ 0:010 A ¼ 10 mA: R 103 O Check: p ¼ VI ¼ ð10 VÞð0:01 AÞ ¼ 0:10 W ¼ 100 mW: Because the applied voltage and the resistance are independent of time, the instantaneous power and current also are independent of time. From (5.7), the total work done in 1 s is w¼
ð t2 t1
pðtÞ dt ¼
ð 1s
ð100 mWÞ dt
0
¼ ð100 mWÞð1 sÞ ¼ 100 mWs ¼ 100 mJ:
Exercise 5.3. The current through a resistor having resistance R ¼ 1kO is I ¼ 5mA. Calculate the instantaneous power dissipated by the resistor, the voltage across the resistor, and the total work done on the resistor in 2 s. Because a resistor converts electrical energy to radiant energy which is then lost forever from the circuit, a resistor always dissipates power. You might think dissipates carries a negative connotation, and sometimes it does; for example, the cost to an electric power company of energy lost in the resistance
4
The ambient-air power-dissipation rating of a component can be exceeded if heat sinks and/or forced cooling are used.
118
5 Work and Power
to dissipate more than that would either exhibit increased resistance (due to overheating) or fail, depending upon the actual power delivered to the resistor and the time for which the power dissipated exceeds the rated dissipation.5 Specifying an appropriate power-dissipation rating for each component in a circuit is as important as specifying any other circuit parameter, such as resistance. Specifying an unnecessarily large power-dissipation rating needlessly increases the size, weight, and cost of a circuit. Specifying a too-small power-dissipation rating for one or more components can cause a circuit to function poorly and fail prematurely because of overheating. In undemanding, low-power applications, radiation, conduction through the leads to a circuit board, and convection by the surrounding air might provide sufficient cooling to keep device temperatures below maximum permissible values. But in some applications and in many integrated circuits in particular, it is impossible or impractical to make components large enough to provide sufficient power dissipation in ambient air. In such cases heat sinks, fans, or even liquid cooling might be required to maintain acceptable operating temperatures.6 Some large mainframe computers require liquid cooling. Even small desktop computers use fans to remove heat from their enclosures and high-performance microprocessors come packaged with an integral heat sink and cooling fan.7 Example 5.4. In steady state, the power radiated from a heated body is given (approximately) by the Stefan-Boltzmann law p ¼ e s A T4;
(5.8)
where e is the emissivity of the body (dimensionless), s ¼ 5:67 108 W m2 K4 is the 5
Common ratings for ordinary composition resistors are 1/8, 1/4, 1/2, and 1 W. Composition resistors having ratings up to 5 W are easily obtained. If a much higher power-dissipation rating is warranted, one can use metallic-film or wire-wound resistors, or use forced cooling, or both. 6 Many books give guidelines for sizing heat sinks with and without forced-air cooling. See, for example, Paul Horowitz and Winfield Hill, The Art of Electronics (2nd Ed.), Cambridge University Press, pp 312 ff. 7 The power dissipated by a modern high-performance microprocessor is on the order of 100 W cm2.
Stefan-Boltzmann constant, A is the surface area of the body, and T is the temperature of the body (K). A certain ¼ W cylindrical composition resistor must operate at or below 150 C to maintain its resistance within 5% of the nominal (specified) value. The emissivity of the surface of the resistor is e ¼ 0.8. What should the surface area of the resistor be (assuming radiation is the only heat-loss mechanism)? Solution: At 150 C and in steady state, the power radiated by the resistor must equal ¼ W, denoted by p0. Thus p0 ¼ e s A T 4 ) A ¼ ¼
p0 e sT 4 0:25 W
ð0:8Þ 5:67 108 W m2 K4 ð423 KÞ4
¼ 1:72 104 m2 : The surface area of a cylindrical resistor having diameter d and length l is given by A ¼ pdl. If the resistor is 1.25 cm long, then the diameter must be d¼
A 1:72 104 m2 ¼ 4:38 103 m ¼ pl p 1:25 102 m
¼ 4:38 mm: The Stefan-Boltzmann law (5.8) gives a pessimistic value for the power-dissipation rating of a resistor because heat also is lost through convection to the surrounding air and conduction through the leads. In absence of heat sinks or forced cooling, radiation accounts for only about 20% of heat loss. Thus the surface area of a resistor need not be as large as that implied by the Stefan-Boltzmann law.
Exercise 5.4. A certain cylindrical resistor is 2 cm long and 0.6 cm in diameter. The operating temperature of the resistor must not exceed 150 C. Assume that radiation is the
5.3 Conservation of Power
119 R1
principal heat-removal mechanism and use the Stefan-Boltzmann law to find the power-dissipation rating of the resistor if the emissivity of the surface is 0.8.
I1
V0 –+
a
I2
2R2 + – V1
R2 ref
V0 = 5 V, V1 = 10 V, R1 = 20 Ω , R2 = 100 Ω
Fig. 5.5 See Example 5.5
5.3 Conservation of Power Energy is conserved. If all energy sources (e.g., current and voltage sources) and circuit components are accounted for, the total energy dissipated (work done) in a circuit equals zero (recall that, according to the passive sign convention, energy generated is negative). We may express the total instantaneous work done in a circuit comprising N elements as w ¼ w1 þ w2 þ þ wN ¼ 0;
(5.9)
Solution: Writing Kirchhoff’s current law at the node a gives Va V0 Va Va V1 þ þ ¼0 R1 R2 2R2 2R2 V0 þ R1 V1 ; ) Va ¼ 3R1 þ 2R2 whence
where wk is the work done in the kth element. It follows that total power dissipated by the circuit also equals zero; that is dw dw1 dw2 dwN þ þ þ ¼0 ¼ dt dt dt dt
I1 ¼ and
(5.10) I2 ¼
or p ¼ p1 þ p2 þ þ pN ¼ 0:
V a V0 V1 3V0 ¼ ; R1 3R1 þ 2R2
(5.11)
The most frequent uses of (5.11) are (1) calculating the power requirements of a circuit (sizing a power supply) and (2) specifying heat-removal methods, such as heat sinks, fans, and liquid cooling. Also, the fact that power is conserved can provide a useful check on the correctness of an analysis.8
Va V1 R2 V0 ðR1 þ R2 ÞV1 : ¼ 2R2 R2 ð3R1 þ 2R2 Þ
From (5.5) and (5.6), the powers dissipated by the circuit elements are pR1 ¼ R1 I12 ¼ p R2 ¼
R1 ðV1 3V0 Þ2 ð3R1 þ 2R2 Þ2
Va2 ð2R2 V0 þ R1 V1 Þ2 ¼ ffi 213:02 mW; R2 R2 ð3R1 þ 2R2 Þ2
p2R2 ¼ 2R2 I22 ¼ Example 5.5. Find the power dissipated by each element in the circuit of Fig. 5.5. Show that the total power dissipated equals zero.
ffi 7:40 mW;
2½R2 V0 ðR1 þ R2 ÞV1 2 R2 ð3R1 þ 2R2 Þ2
ffi 144:97 mW; pv0 ¼ V0 I1 ¼
V0 ðV1 3V0 Þ 3R1 þ 2R2
ffi 96:15 mW; 8
Equation (5.11) states that the total power dissipated equals zero. It is also true that the total power delivered equals zero, or that the total power dissipated equals the total power delivered (in a circuit).
pv1 ¼ V1 I2 ¼
V1 ½R2 V0 ðR1 þ R2 ÞV1 R2 ð3R1 þ 2R2 Þ
ffi 269:23 mW:
120
5 Work and Power i0
The total power dissipated by the circuit is R1
pR1 þ pR2 þ p2R2 þ pv0 þ pv1 ¼ 0:
+
Note the use of the passive sign convention; e.g., to compute the power dissipated by the voltage source, we take the positive direction for current into the positive terminal of the source.
Exercise 5.5. Show that the total power dissipated in the circuit of Exercise 5.2 equals zero. Electrical energy provided by a source can be derived from an electrochemical reaction (as in a battery), from electromechanical devices (such as a generator), from radiation (as in a solar cell), or other means. The electrical energy provided to a circuit component might be converted to rotational mechanical energy (as in an electric motor), to heat (as in a resistor or an electric heater) or other electromagnetic radiation (as in a radio transmitting antenna), or other form. In all cases, total energy and power are conserved. Also in all cases, at least some electrical energy is converted to heat, not all of which can be recovered for good use. No energy-conversion device is 100% efficient.
v0 +–
va va v0 R2 ðv0 þ R1 i0 Þ þ i0 ¼ 0 ) va ¼ ; R2 R1 R1 þ R2 whence i1 ¼ ¼
va v0 þ R1 i0 ¼ ; v1 ¼ v0 va R2 R1 þ R2 R1 ðv0 R2 i0 Þ : R1 þ R2
From (5.5) and (5.6), the instantaneous powers dissipated by the circuit elements are v21 R1 ðV0 R2 I0 Þ2 ¼ cos2 ðo tÞ; R1 ðR1 þ R2 Þ2
pR2 ¼ R2 i21 ¼
1 p^ ¼ R maxi2 ðtÞ ¼ maxv2 ðtÞ ; R
(5.13)
R2
Example 5.6. See Fig. 5.6, where v0 ¼ V0 cosðo tÞ; i0 ¼ I0 cosðo tÞ. Obtain expressions for the instantaneous and peak powers dissipated by each element. Solution: Writing Kirchhoff’s current law at node a gives
The peak power, denoted by p^, associated with a current and voltage is the maximum value of the magnitude of the instantaneous power caused to be dissipated by the current and voltage. In general,
From (5.12) and Ohm’s law, the peak power dissipated by a resistor having resistance R is given by
i1
where i and v are the current through and voltage across the resistor, respectively. Unlike instantaneous power, peak power is not conserved (peak power is non-negative).
pR1 ¼
(5.12)
a
–
Fig. 5.6 See Example 5.6
5.4 Peak Power
p^ ¼ maxjpðtÞj ¼ maxjvðtÞ iðtÞj:
v1
R2 ðR1 I0 þ V0 Þ2
cos2 ðo tÞ; ðR1 þ R2 Þ2 V0 ðR1 I0 þ V0 Þ 2 pv0 ¼ v0 i1 ¼ cos ðo tÞ; R1 þ R2 R1 I0 ðV0 R2 I0 Þ 2 pi0 ¼ v1 i0 ¼ cos ðo tÞ: R1 þ R2 As a check, we confirm that pR1 þ pR2 þ pv0 þ pi0 ¼ 0. Because max½cos2 ðo tÞ ¼ 1, the peak powers dissipated by the elements are given by
5.4 Peak Power
121
p^R1 ¼ p^R2 ¼
R1 ðV0 R2 I0 Þ2 ðR1 þ R2 Þ2 R2 ðR1 I0 þ V0 Þ2 2
RS
;
+ – VS
b VS = 24V, RS = 8 Ω
;
ðR1 þ R2 Þ jV0 ðR1 I0 þ V0 Þj p^v0 ¼ ; R1 þ R 2 jR1 I0 ðV0 R2 I0 Þj : p^i0 ¼ R1 þ R 2
Fig. 5.7 See Example 5.7
RS +
VS –
Exercise 5.6. The instantaneous power dissipated by a certain device is given by
a
R1
R2
VS = 25 V, RS = 5 Ω, R1 = 100 Ω
Fig. 5.8 See Example 5.8
p ¼ P0 cosðo tÞ cosðo t þ yÞ; P0 > 0: Obtain an expression for the peak power dissipated. Peak power is of interest partly because there can occur relatively short-duration (transient) current or voltage spikes in a circuit, some of which can have very large amplitudes. A large spike can transfer a large amount of energy to a device in a very short time, which means that the instantaneous power dissipated by the device is very large during that time. That energy might be sufficient to destroy the device, even if the device were capable of absorbing the same amount of energy over a longer time. As an analogy, the total energy transferred to a tree by an average lightning strike might be only a fraction of the energy received by the tree from the sun in the course of an average month. But such a strike could destroy the tree, whereas the sunlight would not. Peak power is of interest also because all physical sources (and other components) are peak-power-limited; that is, there is a limit to the magnitude of the instantaneous power that can be dissipated by any physical source or component. A peak-power limit on an ideal voltage source limits the current the source can provide (the current through the source). Similarly, a peak-power limit on an ideal current source limits the voltage the source
can produce. For example, if a current source produces current I and the maximum possible voltage across the source is Vmax , then the source is peak-power limited to pmax ¼ Vmax I. Example 5.7. See Fig. 5.7. The source VS is peak-power limited to 48 W. What is the minimum resistance that one should connect to the terminals a–b? Solution: The maximum current the source can deliver is Imax ¼ pmax =VS ¼ 2 A. (a) The minimum resistance one should connect to the terminals is obtained as follows: VS VS ¼ Imax ) Rmin ¼ RS ¼ 4 O: RS þ Rmin Imax
Example 5.8. In Fig. 5.8, the maximum instantaneous power the source VS can deliver is 50 W. What is the maximum possible current through the source? What is the minimum allowable value of the resistance R2? Solution: The maximum possible current through the source is
122
5 Work and Power a
Imax
pmax 50 W ¼ ¼ ¼ 2 A: VS 25 V
+ – VS
Thévenin source model
a
The actual current through the source is given by I¼
RS
b
⇒
source
a
b IS
Norton source model
RS
b
VS : RS þ R1 kR2
Fig. 5.9 Equivalent source models, where VS ¼ RS IS
It follows that ðRS þ R1 kR2 Þmin
+ + V S –
VS 25 V ¼ ¼ ¼ 12:5 O Imax 2A
RL
VL
–
Fig. 5.10 Pertaining to the definition of available power (see (5.17))
and ðR1 kR2 Þmin ¼
R1 ðR2 Þmin ¼ 12:5O RS R1 þ ðR2 Þmin
The power delivered to the load equals zero for both RL ¼ 0 and RL ! 1, so must have a maximum value, which we can find by solving
¼ 7:5 O ¼ R; which yields ðR2 Þmin ¼
R1 R ð100OÞð7:5 OÞ ¼ ffi 8:12 O: R1 R 100 O 7:5O
5.5 Available Power A physical source can be modeled using either the The´venin or Norton equivalent for the source at the source terminals, as illustrated by Fig. 5.9. If VOC ; ISC denote the open-circuit voltage and shortcircuit current, respectively, at the terminals of the source, then VS ¼ VOC ; RS ¼
VOC ; IS ¼ ISC : ISC
(5.14)
A The´venin or Norton source model is by its nature peak-power limited. To show this, we consider the circuit in Fig. 5.10, where the power delivered to the load RL by the The´venin source model is given by
PL ¼
RS
VL 2 1 VS RL ¼ RL RS þ RL RL
2 ¼
VS 2 RL ðRS þ RL Þ2
: (5.15)
" # dPL d VS 2 RL ¼0) dRL dRL ðRS þ RL Þ2 ¼
VS 2 ðRS þ RL Þ
2
2VS 2 RL ðRS þ RL Þ3
¼ 0:
(5.16)
Thus the load resistance that draws maximum power from the source is RL ¼ RS , and the maximum power that can be drawn from the source is given by PL max ¼
VS 2 RS ðRS þ RS Þ
2
¼
VS 2 : 4RS
(5.17)
In other words, the The´venin source model is peak power limited. The maximum power that can be drawn from the source, given by (5.17), is called the available power for the source. The resistance RS is called the internal resistance of the source. These important quantities are discussed at length in Section 5.16. Exercise 5.7. Show without using (5.17) that the available power for a Norton source model is given by
5.6 Time Averages
123
PL max
IS 2 RS : ¼ 4
(5.18)
Exercise 5.8. A certain fully-charged battery has an open-circuit terminal voltage of 12.6V and an internal resistance of approximately 0.1O. Draw circuit diagrams for the The´venin and Norton models for the battery. What is the maximum power that can be drawn from the battery? What is the maximum current that can be drawn from the battery?
Exercise 5.9. The power available from a certain source is 50W. A 10 O load draws 1A from the source, where positive current exits the positive terminal of the source. Obtain the The´venin and Norton models for the source.
5.6 Time Averages In most circuit applications, average power dissipated (or delivered) is of more interest than instantaneous power. Household light bulbs, electric heaters, electric water heaters, electric generators, electric motors, audio amplifiers, radio transmitters, and a host of other devices, circuits, and systems are rated according to average power dissipated or delivered, not instantaneous power. Intuitively, average power dissipated over an interval is the total work done in the interval, divided by the duration of the interval. For average power to be meaningful, the averaging interval must be long enough to obtain a true average; that is, the duration of the interval must be such that increasing the duration yields no significant change in the calculated average power. Physical instruments that measure average power must use a finite interval. Otherwise, a measurement could never be completed. But using mathematical models for physical currents and voltages, we can calculate average power over an
infinite interval, which is easier than attempting to decide how long to make the interval based upon knowledge of each particular instantaneous power of interest. Average current and voltage, such as the average voltage produced by a power supply and the average current provided by a battery charger, also are of interest. Average currents and voltages also are of considerable importance in electronic circuits, as you will find when you study that subject. In this section, we introduce time averages in general. We describe how one computes the average value of a function of time, regardless of whether the function represents power, current, voltage, or other physical quantity. The relations developed in this section are used repeatedly in subsequent sections and chapters, and most likely in subsequent courses and later, in practice. The time average of a function of time x(t) is denoted by x and is defined by ð 1 T x ¼ lim xðtÞ dt: (5.19) T!1 T 0
Note: In some texts, and probably in later work, you will see the time average of a function defined as x ¼ lim
T!1
1 T
ð T=2 xðtÞ dt:
(5.20)
T=2
It is easy to cook up functions for which the two definitions give different results; for example, ( xðtÞ ¼
5 V;
t 0;
10 V;
t > 0:
:
For functions that are either constant or periodic, the two definitions give identical results, in which cases (5.19) is often easier to apply than (5.20). Also, (5.19) is more consistent with measurements, which must begin at some finite time.
124
5 Work and Power
The dimension of an average is that of the quantity averaged; e.g., if x(t) in (5.19) is a voltage, the dimension of the average x is voltage. Because time averages are the only averages we use, we refer to the right side of (5.19) as simply the average of x(t). Two specific averages are especially useful. First, the average of a constant is the constant itself: a ¼ a:
(5.21)
First, if a is a constant a x ¼ a x:
(5.23)
In words, the average of the product of a constant and a function of time is the product of the constant and the average of the function of time. Equation (5.23) follows from the fact that the constant a can be taken outside both the integral and the limiting operation in (5.19). Second, if x1 ; x2 ; ; xN denote functions of time, then
Second, the average of a sinusoid equals zero: cosðo t þ yÞ ¼ 0; o 6¼ 0:
x1 þ x2 þ þ xN ¼ x1 þ x2 þ þ xN : (5.22)
Equation (5.21) is obtained from (5.19) as follows: Because a is independent of time, lim
T!1
1 T
ðT 0
a dt ¼ lim
T!1
(5.24)
1 1 t¼T ½a tt¼0 ¼ lim ½a T T!1 T T
¼ lim ðaÞ ¼ a: T!1
In words, the time average of a sum of functions equals the sum of the time averages of the functions. Equation (5.24) follows from the fact that both integration and limiting distribute over a sum. In addition to the relations given above, a few trigonometric identities are useful in finding averages of sinusoidal functions of time, as illustrated by the following examples.
Equation (5.22) is obtained from (5.19) as follows: lim
1
T!1 T
ðT
t¼T
1 1 cosðo t þ yÞdt ¼ lim sinðo t þ yÞ T!1 T o 0 t¼0 1 1 1 ¼ lim sinðo T þ yÞ sinðyÞ ¼ 0: T!1 T o o
because (for o 6¼ 0) the quantity in the brackets is finite. The time average of a function of time exists if the function is bounded; i.e., if jxðtÞj<1 for all values of time t.9 We are concerned only with averages of functions representing physical currents, voltages, and powers, all of which are bounded. Furthermore, in this introductory treatment, we are concerned only with averages of constant and periodic functions. You might learn more about time averages in general in subsequent courses. Two useful properties of averages in general follow immediately from (5.19):
Example 5.9. Obtain an expression for the average value of xðtÞ ¼ cos2 ðo t þ yÞ, where o>0 and y is a constant but otherwise arbitrary angle. Solution: We use the identity cos2 ðaÞ
1 1 þ cosð2 aÞ 2 2
to obtain xðtÞ ¼ cos2 ðo t þ yÞ ¼
1 1 þ cosð2 o t þ 2 yÞ: 2 2
From (5.24), 1 1 1 1 x ¼ þ cosð2o t þ 2 yÞ ¼ þ cosð2o t þ 2 yÞ: 2 2 2 2 From (5.21), 1 1 ¼ : 2 2
9
This condition is more stringent than necessary, but in this book, we do not need to compute time averages of functions not satisfying the condition.
From (5.23) and (5.22),
5.6 Time Averages
1 1 cosð2 o t þ 2 yÞ ¼ cosð2 o t þ 2 yÞ ¼ 0: 2 2
125
From (5.21), 1 1 cosðy1 y2 Þ ¼ cosðy1 y2 Þ; 2 2
Thus 1 x ¼ cos2 ðo t þ yÞ ¼ : 2
because y1 y2 is a constant. Thus 1 x ¼ cosðo t þ y1 Þ cosðo t þ y2 Þ ¼ cosðy1 y2 Þ: 2
Exercise 5.10. Obtain an expression for the average of xðtÞ ¼ sin2 ðo t þ yÞ, where o>0 and y is a constant but otherwise arbitrary angle. You may use the result obtained in Example 5.9.
Example 5.10. Obtain an expression for the average of xðtÞ ¼ cosðo t þ y1 Þ cosðo t þ y2 Þ, where o>0 and y1 ; y2 are constant but otherwise arbitrary angles. Solution: We use the identity 1 1 cosðaÞ cosðbÞ cosða þ bÞ þ cosða bÞ 2 2
Exercise 5.11. Obtain an expression for the average of xðtÞ ¼ ½cosðo t þ y1 Þ þ cosðo t þ y2 Þ2 , where o>0 and y1 ; y2 are constant but otherwise arbitrary angles.
Exercise 5.12. Show by example that if x1 ; x2 are both functions of time, then x1 x2 6¼ x1 x2 : That is, show that the average of the product of two functions is in general not equal to the product of the average values.
to obtain xðtÞ ¼ cosðo t þ y1 Þ cosðo t þ y2 Þ 1 1 cosð2 o t þ y1 þ y2 Þ þ cosðy1 y2 Þ: 2 2 From (5.24), 1 1 cosð2 o t þ y1 þ y2 Þ þ cosðy1 y2 Þ 2 2 1 1 ¼ cosð2 o t þ y1 þ y2 Þ þ cosðy1 y2 Þ: 2 2
x ¼
From (5.23) and (5.22), 1 cosð2 o t þ y1 þ y2 Þ 2 1 ¼ cosð2 o t þ y1 þ y2 Þ ¼ 0: 2
Example 5.11. Obtain an expression for the average of xðtÞ¼ cosðo1 tþy1 Þþcosðo2 tþy2 Þ, where o2 >o1 >0 and y1 ;y2 are constant but otherwise arbitrary angles. Solution: We use the identity cosðaÞ cosðbÞ
1 1 cosða þ bÞ þ cosða bÞ 2 2
to obtain x ¼ cosðo1 t þ y1 Þ cosðo2 t þ y2 Þ
1 cos½ðo1 þ o2 Þ t þ y1 þ y2 2 1 þ cos½ðo1 o2 Þ t þ y1 y2 : 2
From (5.24) and (5.23)
126
5 Work and Power
x ¼
P ¼ v i ¼ R i2 ¼ R i 2
1 cos½ðo1 þ o2 Þ t þ y1 þ y2 2 1 þ cos½ðo1 o2 Þ t þ y1 y2 : 2
From (5.22), the last two terms equal zero because o1 6¼ o2 . Thus x ¼ cosðo2 t þ y1 Þcosðo1 t þ y2 Þ ¼ 0; o1 6¼ o2 :
Exercise 5.13. Obtain an expression for the average of xðtÞ¼½cosðo1 tþy1 Þþcosðotþy2 Þ2 , where o2 >o1 >0 and y1 ;y2 are constant but otherwise arbitrary angles.
1 2 1 2 v ¼ v; R R (5.27)
where i and v are the current through and voltage across the resistor. The quantities i2 and v2 are called the mean squared amplitudes of the current i and the voltage v, respectively.10 If the current through a resistor is a constant given by i ¼ I0 , then from (5.6), the instantaneous power dissipated by the resistor is a constant given by p ¼ I0 2 R, where R is the resistance of the resistor. It follows that if a resistor having resistance R is subjected to a constant current i ¼ I0 or a constant voltage v ¼ V0 , the instantaneous power dissipated, the peak power dissipated, and the average power dissipated are equal and given by p ¼ p^ ¼ P ¼ I0 2 R or p ¼ p^ ¼ P ¼
Results obtained in Example 5.9, Example 5.10 and Example 5.11 are collected below for future reference. 1 cos2 ðo t þ yÞ ¼ ; o 6¼ 0; 2
V0 2 : (5.28) R
Example 5.12. The voltage across a 100 O resistor is 24 V. From (5.6), the instantaneous power dissipated is
1 cosðo t þ y1 Þ cosðo t þ y2 Þ ¼ cosðy1 y2 Þ; o 6¼ 0; 2 cosðo2 t þ y1 Þcosðo1 t þ y2 Þ ¼ 0; o1 6¼ o2 :
p¼ VI ¼V
(5.25)
V V2 ¼ R R
ð24 VÞ2 ffi 5:76W: ¼ 100 O
5.7 Average Power
(5.29)
From (5.28), the average power dissipated and peak power dissipated are
The average power dissipated by a two-terminal element is conventionally denoted by P rather than p, and is defined by P ¼ p ¼ v i:
or P ¼ v i ¼
P ¼ p^ ffi 5:76W
(5.30)
(5.26)
In (5.26), p is the instantaneous power dissipated by the element and v and i are the instantaneous voltage across and current through the element. Average power is conserved, as can be shown by applying (5.24) to (5.11). Equation (5.26) applies to any two-terminal element. From (5.26) and Ohm’s law, the average power dissipated by a resistor having resistance R is given by
From (5.27) and (5.25), the average power dissipated by a resistor having resistance R subjected to a sinusoidal current or voltage is given by
10
In this context, mean is a synonym for average.
5.7 Average Power
127
iðtÞ ¼ I0 cosðo t þ yÞ ) P ¼ R I0 2 cos2 ðo t þ yÞ ¼
I0 2 R ; o 6¼ 0; 2
vðtÞ ¼ V0 cosðo t þ yÞ ) P ¼ ¼
1 2 2 V0 cos ðo t þ yÞ R
Solution: By the definition of an ideal current source, the current through the resistor equals i0. From (5.31), the average power dissipated by the resistor is given by
V0 2 ; o 6¼ 0: 2R
PR ¼ (5.31)
Example 5.13. The voltage at the terminals of a certain 1500 W electric heater when the heater is operating is
I0 2 R : 2
The current entering the positive terminal of the voltage source is i0. Thus (passive sign convention) the average power dissipated by the voltage source is given by Pv ¼ v0 i0 ¼ V0 I0 cosðo tÞ cosðo t þ yÞ:
vðtÞ ¼ V0 cosð2 p f tÞ; V0 ¼ 165V: From (5.23) and (5.25), Find the hot resistance of the heater element. Solution: From (5.31), P¼
V0 2 V0 2 ð165 VÞ2 ¼ 1500W ) R ¼ ¼ 2R 2 P ð2Þð1500 WÞ
ffi 9:08 O:
Pv ¼ V0 I0 cosðo tÞ cosðo t þ yÞ ¼
V0 I0 cosðyÞ: 2
By Kirchhoff’s voltage law, the voltage vi across the current source is given by v0 R i0 þ vi ¼ 0 ) vi ¼ v0 þ R i0 :
Exercise 5.14. The current through a resistor having resistance R ¼ 15 O is given by
The current i0 exits the terminal designated as positive in the definition of vi, so the average power dissipated by the current source (passive sign convention) is given by
i ¼ I0 cosð2pf tÞ; with I0 ¼ 10 A and f ¼ 60 Hz. Find the instantaneous power, the peak power, and the average power dissipated by the resistor.
Pi ¼ vi i0 ¼ ðv0 þ R i0 Þ i0 ¼ v0 i0 R i0 2 : From (5.24) and results already obtained, Pi ¼ v0 i0 R i0 2 ¼ Pv PR ¼
Example 5.14. Obtain expressions for the average powers dissipated by the elements in the circuit shown in Fig. 5.11.
+ –
v0
+
R i0
vi –
Fig. 5.11 See Example 5.14
i0 = I0 cos (wt + q) v0 = V0 cos (wt) w>0
V0 I0 I0 2 R cosðyÞ ; 2 2
as expected, because total average power is conserved.
Exercise 5.15. Obtain expressions for the average powers dissipated by the elements in the circuit shown in Fig. 5.12.
128
5 Work and Power
R1
i0
i1
R2
i0 = I0 cos (wt) i1 = I1 cos (w t + q) w>0
Fig. 5.12 See Exercise 5.15
p(t) = pˆ =
P=
V02
V02 cos2 (2π f0 t) R
R
V02 2R
t
0 0
1 2f0
1 f0
3 2f0
Fig. 5.13 An illustration of the definitions of peak power and average power
Figure 5.13 shows a graph of instantaneous power for a sinusoidal voltage applied to a resistor. Indicated on the figure are the peak power p^ ¼ V0 2 =R and the average power P ¼ V0 2 =ð2 RÞ. For a sinusoidal current or voltage applied to a resistor, the average power equals one-half of the peak power. In summary, the instantaneous power p, the peak power p^, and the average power P dissipated by a resistor having resistance R and subjected to a sinusoidal current iðtÞ ¼ I0 cosðo t þ yÞ or sinusoidal voltage vðtÞ ¼ V0 cosðo t þ yÞ are given by 9 I0 R p^ I0 R > 2 > > ½1þcosð2otÞ; p^ ¼ I0 R; P ¼ ¼ p¼ > 2 2 > 2 = or o > 0: > > 2 2 2 > > p^ V0 V0 V0 > ; p¼ ½1þcosð2otÞ; p^ ¼ ; P¼ ¼ 2 2R 2R R (5.32) 2
2
Equation (5.32) applies only when the applied current or voltage is sinusoidal and the resistance R is independent of both time and applied current or voltage. It is not difficult to err in this regard. The most common error is applying (5.32) to a resistor subjected
to a non-sinusoidal current or voltage. As an example of a more subtle error, consider an ordinary incandescent light bulb driven by a fixed-amplitude sinusoidal voltage source. The resistance of the light-bulb filament is larger when the filament is hot than when cold. If the frequency of the applied voltage is sufficiently large, the filament does not cool significantly between peaks of the applied voltage, the resistance of the filament remains nearly constant (at the hot value), and the average power delivered to the bulb is given by (5.32). But if the frequency of the applied voltage is sufficiently low, the bulb varies between bright and dark, the resistance of the filament varies between hot and cold (or warm) values, and the average power applied to the bulb cannot be computed using (5.32). In such a case, we might express the resistance as a function of the applied current, which is a function of time, and calculate the average value of the instantaneous power p ¼ i2 ðtÞ R½iðtÞ, but such problems are beyond the scope of this book.
Example 5.15. (a) Obtain expressions for the instantaneous power dissipated (passive sign convention) by each element in the circuit shown in Fig. 5.14. (b) Let v ¼ V0 ¼ 5 V; i ¼ I0 ¼ 2 mA and calculate the peak and average powers dissipated by each element. (c) Let v0 ¼ V0 cosðo tÞ, i0 ¼ I0 cosðo tÞ, with V0 ¼ 5 V, I0 ¼ 2 mA, and o>0. Calculate the peak and average powers dissipated by each element. Solution: (a) We first obtain expressions for the current through and voltage across each element. Kirchhoff’s current law yields
R1 + v – 0
i1 a i2 i0
R2
ref
Fig. 5.14 See Example 5.15
R1 = 1 k Ω R2 = 5 k Ω
5.7 Average Power
129
va v0 va i0 þ ¼0 R1 R2 R2 ðv0 þ R1 i0 Þ ) va ¼ ; R1 þ R 2
R2 I0 V0 p1 ¼ p^1 ¼ P1 ¼ i1 R1 ¼ R1 þ R2 2 ð5 kOÞð2 mAÞ 5 V ¼ ð1 kOÞ 1 kO þ 5 kO ffi 694 mW;
whence
V0 þ R1 I0 p2 ¼ p^2 ¼ P2 ¼ i2 R2 ¼ R1 þ R2 2 5 V þ ð1 kOÞð2 mAÞ ¼ ð5 kOÞ 1 kO þ 5 kO 2
va v0 R2 ðv0 þ R1 i0 Þ v0 ¼ i1 ¼ R1 R1 R1 ðR1 þ R2 Þ : R 2 i 0 v0 va v0 þ R1 i0 ¼ ; i2 ¼ ¼ : R 1 þ R2 R2 R1 þ R2 Let pv denote the power dissipated by the voltage source, pi denote the power dissipated by the current source, p1 the power dissipated by resistor R1, and p2 the power dissipated by resistor R2. The instantaneous powers dissipated are given by R2 i0 v0 pv ¼ v0 i1 ¼ v0 ; R1 þ R2 R2 ðv0 þ i0 R1 Þ pi ¼ i0 va ¼ i0 ; R1 þ R2 R 2 i0 v 0 2 R1 ; p1 ¼ i1 2 R1 ¼ R 1 þ R2 v 0 þ R 1 i0 2 R2 : p2 ¼ i2 2 R2 ¼ R1 þ R2
(b) Because both sources are constant, all currents or voltages in the circuit are constant. Thus the instantaneous, peak, and average powers dissipated by each component are the same. From part (a) above,
R2 I0 V0 pv ¼ p^v ¼ Pv ¼ V0 R1 þ R2 ð5 kOÞð2 mAÞ 5 V ¼ ð5 VÞ 1 kO þ 5 kO ffi 4:17 mW;
R2 ðV0 þ I0 R1 Þ pi ¼ p^i ¼ Pi ¼ I0 R 1 þ R2
½5 kO½5 V þ ð2 mAÞð1 kOÞ ¼ ð2 mAÞ 1 kO þ 5 kO ffi 11:67mW;
2
2
R1
2 R2
ffi 6:81 mW: (c) From part (a), the instantaneous powers dissipated are pv ¼ V0 cosðo tÞ R2 I0 cosðo tÞ V0 cosðo tÞ R1 þ R 2 R 2 I 0 V0 ¼ V0 cos2 ðo tÞ R1 þ R2 V0 R2 I0 V0 ¼ ½1 þ cosð2 o tÞ 2 R1 þ R2 ffi 2:08 ½1 þ cosð2 o tÞ mW; pi ¼ I0 cosðo tÞ R2 ðV0 cosðo tÞ þ I0 cosðo tÞ R1 Þ R1 þ R2 R2 ðV0 þ R1 I0 Þ cos2 ðo tÞ ¼ I0 R1 þ R2 I0 R2 ðV0 þ R1 I0 Þ ¼ 2 R1 þ R 2 ½1 þ cosð2 o tÞ ¼ 5:83½1 þ cosð2 o tÞmW; R2 I0 cosðo tÞ V0 cosðo tÞ 2 R1 R1 þ R2 R2 I0 V0 2 ¼ R1 cos2 ðo tÞ R1 þ R2 1 R2 I0 V0 2 ¼ R1 ½1 þ cosð2 o tÞ 2 R1 þ R2
p1 ¼
ffi 347½1 þ cosð2 o tÞmW;
130
5 Work and Power
We use upper-case letters to denote rms amplitudes because an rms amplitude is independent of time. Thus Irms denotes the rms amplitude of iðtÞ, Vrms denotes the rms amplitude of vðtÞ, I1 rms denotes the rms amplitude of i1 ðtÞ, and so on. The dimension of the rms amplitude of a current or voltage is current or voltage, respectively. The rms amplitude of a current or voltage is the positive square root of the mean (average) of the squared current or voltage. The order of the operations is important: First square the current or voltage, then compute the average, then take the positive square root. In general, these operations are not interchangeable.
and
2 V0 cosðo tÞ þ R1 I0 cosðo tÞ R2 R 1 þ R2 2 V0 þ R1 I0 ¼ R2 cos2 ðo tÞ R 1 þ R2 1 V 0 þ R1 I 0 2 ¼ R2 ½1 þ cosð2 o tÞ 2 R1 þ R2
p2 ¼
ffi 3:40 ½1 þ cosð2 o tÞmW: The peak and average powers are [see (5.32)] p^v ffi 4:17 mW; p^i ffi 11:67 mW; p^1 ffi 694 mW; p^2 ffi 6:81 mW;
Example 5.16. Obtain an expression for the rms amplitude of a constant current i ¼ I0, where I0 might be positive or negative. Solution: From (5.21), the mean squared amplitude is
and
i2 ¼ I0 2 ¼ I0 2 : Pv ffi 2:08 mW; Pi ffi 5:83 mW;
From (5.33), the rms amplitude is
P1 ffi 347 mW; P2 ffi 3:40 mW;
Irms ¼
pffiffiffiffiffiffi I0 2 ¼ jI0 j:
respectively. All physical circuit components are peak-powerlimited and average-power limited. Typically, the average power a component can dissipate is less than the (short-term) peak power the component can dissipate. For example, an audio amplifier rated at 100 W might be able to provide as much as 150 W for a short time (a few milliseconds), but cannot provide more than 100 W on average (over a long time).
Example 5.17. Obtain an expression for the rms amplitude of a sinusoidal voltage v ¼ V0 cosðo t þ yÞ. Solution: From (5.25), the mean squared amplitude of a sinusoidal voltage having peak amplitude jV0 j is given by v2 ¼ V0 2 cos2 ðo t þ yÞ ¼
5.8 Root Mean Squared (RMS) Amplitude of a Current or Voltage The root mean squared amplitudes (rms amplitude) of a current and voltage are denoted by the subscript rms and are defined by Irms
qffiffiffiffiffiffiffiffiffi ¼ i2 ðtÞ;
Vrms
qffiffiffiffiffiffiffiffiffiffi ¼ v2 ðtÞ:
(5.33)
V0 2 : 2
From (5.33), the rms amplitude of a sinusoidal voltage having peak amplitude jV0 j is given by
Vrms
qffiffiffiffiffiffiffiffiffiffi ¼ v2 ðtÞ ¼
sffiffiffiffiffiffiffi V0 2 jV0 j ¼ pffiffiffi : 2 2
5.9 Average Power Dissipated in a Resistive Load
131
Example 5.17 shows that the rms amplitudes of a sinusoidal current and a sinusoidal voltage are given by
5.9 Average Power Dissipated in a Resistive Load
9 jI0 j > iðtÞ ¼ I0 cosðo t þ yÞ ) Irms ¼ pffiffiffi > = 2 o>0: (5.34) > jV 0 j > ; p ffiffi ffi vðtÞ ¼ V0 cosðo t þ yÞ ) Vrms ¼ 2
From (5.33), Irms 2 ¼ i2 and Vrms 2 ¼ v2 , so we may express the power dissipated by a resistive load as
The mean squared and rms amplitudes of a sinusoidal current or voltage having frequency o > 0 are independent of both the frequency o and the initial phase y of the current or voltage. Equation (5.33) applies to any current or voltage. Equation (5.34) applies only to sinusoidal currents and voltages. Because the rms amplitude of a sinusoidal current or voltage is independent of the initial phase of the current or voltage (of the angle y in (5.34)), the rms amplitude of a sinusoidal current or voltage is independent of the algebraic sign of the current or voltage and of whether the current or voltage is expressed as a cosine or sine; for example, 1
0
C B vðtÞ ¼ V0 sinðo t þ yÞ ¼ V0 cos@ot þ y p=2 A |fflfflfflffl{zfflfflfflffl} y0
jV0 j ) Vrms ¼ pffiffiffi : 2
Exercise 5.16. Give the rms amplitude of each of the following: (a) iðtÞ ¼ 25 mA, (b) vðtÞ ¼ 5V, (c) vðtÞ ¼ 10 cosð2p f t þ p=4ÞV, (d) iðtÞ ¼ 10 sinð2p f t p=4ÞmA:
P ¼ Irms 2 R
or P ¼
Vrms 2 : R
Under the passive sign convention, the power dissipated by a resistor is positive. Thus, from (5.36), the average power dissipated by a resistor having resistance R also can be expressed as pffiffiffiffiffi P ¼ P2 ¼
s ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi Vrms 2 2 Irms R ¼ Vrms Irms ; (5.37) R
where Irms and Vrms are the rms amplitudes of the current through and voltage across the resistor. Equations (5.36) and (5.37) apply (in general) only to resistive loads and to power delivered by a source. Example 5.18. Refer to Fig. 5.15, where i0 ¼ I0 cosðo tÞ and v0 ¼ V0 cosðo tÞ, with o > 0. Obtain expressions for the rms amplitudes of vR ; v1 ; iR . Then obtain expressions for the average powers dissipated in the resistors. Solution: Kirchhoff’s current law gives v1 v1 v0 þ i0 ¼ 0 R R Ri0 þ v0 RI0 þ V0 ¼ cosðo tÞ; ) v1 ¼ 2 2 whence V1 rms ¼
In general, rms amplitudes are not additive, because (in general)
jRI0 þ V0 j pffiffiffi : 2 2
It follows that qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi qffiffiffiffiffiffi qffiffiffiffiffiffi ðv1 þ v2 Þ2 6¼ v1 2 þ v2 2 :
(5.35)
For example, if V ¼ V1 þ V2 , where V1 ¼ 5V and V2 ¼ 5V, then V ¼ V1 þ V2 ¼ 0 and Vrms ¼ 0 whereas V1 rms þ V2 rms ¼ 10V.
(5.36)
iR ¼ and
v1 V1 rms jRI0 þ V0 j pffiffiffi ) IR rms ¼ ¼ R R 2 2R
132
5 Work and Power
V0 RI0 cosðo tÞ vR ¼ v 0 v1 ¼ 2 jV0 RI0 j pffiffiffi : ) VR rms ¼ 2 2 The average power dissipated in the resistor on the left is given by P1 ¼
VR rms 2 ðV0 RI0 Þ2 ¼ : R 8R
The average power dissipated in the resistor on the right is given byP2 ¼
V1 rms 2 ðRI0 þ V0 Þ2 ¼ R 8R
Fig. 5.16 See Example 5.19 i
whose peak amplitude is approximately 170 V. Using rms amplitudes in power calculations involving sinusoidal currents and voltages avoids pffiffiffi cluttering expressions with the factors1=2 and 1= 2. It follows from (5.36) that any two currents or voltages having the same rms amplitudes deliver the same average power to a resistive load, even if the current or voltage waveforms are different. In other words, two currents or two voltages having equal rms amplitude are equally effective in delivering power to a resistive load.11
and by P2 ¼ IR rms R ¼ 2
RI0 þ V0 pffiffiffi 2 2R
R
Example 5.19. In the circuit shown in Fig. 5.16, R ¼ 1:5 kO and
2 R¼
ðRI0 þ V0 Þ2 : 8R
iðtÞ ¼ I0 cosð2 p f tÞ; I0 ¼ 3mA: Find the average powers dissipated by the resistor and the source. Solution: The rms amplitude of the current is
Exercise 5.17. Refer to Fig. 5.15 and Example 5.17. Assume V0 > 0; I0 > 0. Obtain expressions for the average powers dissipated by the sources. Show that the total power dissipated equals zero.
jI0 j Irms ¼ pffiffiffi ¼ 2:12 mA: 2 Thus the average power dissipated by the resistor is
In the electric utility industry, where currents and voltages are sinusoidal and where power is a primary concern, it is convenient and conventional to specify currents and voltages in terms of their rms amplitudes, rather than peak amplitudes. For example, the voltage available at a residential wall receptacle in North America is commonly said to be 120 V, which actually is the rms amplitude of a 60-Hz sinusoidal voltage
2 PR ¼ Irms 2 R ¼ 2:12 103 A ð1500 OÞ ¼ 6:75 mW: Because power is conserved, the average power dissipated by the source (passive sign convention) is Pi ¼ PR ¼ 6:75 mW:
+ vR –
v0
+ –
R
v1 i0
iR R 11
Fig. 5.15 See Example 5.18
For this reason, the rms amplitude of a current or voltage also is called the effective value of the current or voltage; however, this terminology is falling into disuse.
5.12 Measurement of RMS Amplitude
133
5.10 Summary: Power Relations Table 5.1 summarizes definitions and relations given above.
and that under that condition the output is a constant voltage having amplitude 5 V. Such terminology is common in practice, and you should understand it. But in analysis and design, stick with precise terminology.
5.11 Notation 5.12 Measurement of RMS Amplitude Conventionally, rms is appended to the unit of a current or voltage to denote rms amplitude; for example, V ¼ 10 Vrms. However, keep in mind that Vrms and Arms are not true units. For example, the relation between rms amplitude and peak amplitude of a current or voltage depends upon the waveform of the current or voltage. Alternatively, we often use expressions such as Vrms ¼ 10 V, which means that the rms amplitude of v(t) is 10 V. We do not express timedependent currents or voltages using rms amplitudes because rms amplitude is independent of time. For example, we do not write expressions such as irms ðtÞ ¼ 10 cosðo tÞpV. ffiffiffi Moreover, we avoid expressions such as vðtÞ ¼ 2Vrms cosðo tÞ, which is invalid for o ¼ 0. Other pseudo units you will encounter are Vac or VAC, which are synonymous with Vrms, and Vdc or VDC, which indicate a constant voltage. For example, a nameplate rating of 120 VAC @ 60 Hz in and 5 VDC out on small plug-in power supply means the supply should be plugged into an outlet providing a 60 Hz sinusoidal voltage having rms amplitude 120 V,
No instrument can take the limits specified by the mathematical definitions sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð 1 T0 2 lim i ðtÞdt ; Irms ¼ T!1 T0 0 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð 1 T0 2 lim v ðtÞ dt; Vrms ¼ T!1 T0 0
because such measurements would take forever. Fortunately, we do not need to average forever to measure the rms amplitude of a physical current or voltage. The rms amplitude of a current or voltage can be measured with any necessary precision by an instrument that computes rms amplitude using an average over a finite but sufficiently long interval. The required averaging time T0 depends upon the nature of the current or voltage and upon the required precision of the result. For example, let i ¼ I0 cosðo tÞ. Then, for finite T0 a measurement of rms amplitude yields
Table 5.1 Expressions for power dissipation in a resistor Quantity General (Definition) Current through or voltage across a resistor (any waveform) Instantaneous p ¼ v i v2 2 p ¼ i R ¼ power R
Peak power
Average power
p^ ¼ R maxi2 2 maxv ¼ R
p^ ¼ maxj pj
P ¼ lim
1 T!1 T
RT 0
p dt
P ¼ Irms 2 R 2
Vrms R ¼ Vrms Irms ¼
(5.38)
Constant current I0 through or voltage V0 across a resistor
Sinusoidal current I0 cosðo tÞ through or voltage V0 cosðo tÞ across a resistor
p ¼ I0 2 R
p ¼ I0 2 Rcos2 ðo tÞ
V0 2 R ¼ V0 I0
V0 2 cos2 ðo tÞ R ¼ I0 V0 cos2 ðo tÞ V0 2 p^ ¼ I0 2 R ¼ R ¼ V0 I 0
¼
p^ ¼ I0 2 R V0 2 R ¼ V0 I0 P ¼ I0 2 R ¼
2
V0 R ¼ V0 I0
¼
¼
I0 2 R V0 2 ¼ 2R 2 V0 I0 ¼ 2
P¼
134
Irms
5 Work and Power
sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð ð 1 T0 2 1 T0 2 ffi i ðtÞ dt ¼ I0 cos2 ðo t Þ dt T0 0 T0 0 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð I0 2 T0 ½1 þ cosð2 o t Þ dt ¼ 2 T0 0 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi I0 2 1 T0 þ sinð2 o T0 Þ ¼ 2 T0 2o sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi I0 2 I0 2 þ ¼ sinð2 o T0 Þ 2 4 o T0 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi j I0 j sinð2 o T0 Þ ¼ pffiffiffi 1 þ : (5.39) 2 o T0 2
pffiffiffi The factor jI0 j= 2 is the mean squared amplitude (the desired result). Because jsinð2 o T0 Þj 1, the error (magnitude) is bounded as jI0 j jej pffiffiffi 2
rffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 jI0 j 1þ pffiffiffi : 2 o T0 2
We assume 2 o T0 1 and use the approximation pffiffiffiffiffiffiffiffiffiffiffi 1 þ x ffi 1 þ x=2 to obtain pffiffiffi jI 0 j 1 jI0 j jI0 j= 2 pffiffiffi ¼ : jej pffiffiffi 1 þ 4 o T0 4 o T0 2 2 Thus the error expressed as a percent of the true value is bounded as jejð%Þ
100 4 ffi ; 4 o T0 f T 0
(5.40)
where f is frequency in hertz (o ¼ 2p f ). For example, if the magnitude of the error must be smaller than 1% of the actual rms amplitude, we would require 4 4 < 1 ) T0 > : f T0 f For any specified percent error, the required averaging time decreases as the frequency is increased. A longer averaging time is needed for a low-frequency sinusoid than for a higher frequency one. Conversely, if the averaging time T0 is fixed, increasing (decreasing)
i t1
t
Fig. 5.17 Pertaining to the time required to measure the rms amplitude of a current or voltage (see text)
the frequency of an applied current or voltage increases (decreases) the accuracy of the measurement. Again, the required averaging time depends upon both the required precision of the result and one or more properties of the current or voltage (frequency, in this example). More generally, to measure the rms amplitude of a non-sinusoidal, time-varying current or voltage, we need only average over a time much longer than the duration of the most slowly varying component of the current or voltage. For example, inspection of the current waveform shown in Fig. 5.17 suggests that the period of the most slowly varying component of the waveform is (approximately) equal to the time t1 shown on the graph. To measure the rms amplitude of the current shown in Fig. 5.17, we would average for a time much longer than t1. Example 5.20. The averaging time employed by a certain rms voltmeter is fixed and is such that the maximum percent error in a measurement of the rms amplitude of a 100 Hz sinusoidal voltage is 0.1%. What is the maximum percent error in a measurement of the rms amplitude of a 10 Hz sinusoidal voltage? Solution: We use (5.40) to find the averaging time: 4 40 40 ¼ 0:1 ) T0 ¼ ¼ ¼ 0:4 s: f T0 f 100 Hz We use (5.40) f ¼ 10 Hz to obtain max½jejð%Þ ffi
with
T0 ¼ 0:4 s
and
4 4 ¼ 1%: ¼ f T0 ð10 HzÞð0:4 sÞ
5.13 Dissipation Derating
Exercise 5.18. A certain rms voltmeter is advertised as providing 0.1% accuracy for sinusoidal voltages having frequencies from 10 Hz to 10 MHz. (a) What is the minimum averaging time used by the voltmeter? (b) If the error is 0.1% at 10 Hz, what is the error at 10 MHz? Assume that finite averaging time is the only source of error.
Exercise 5.19. The rms amplitude of a certain voltage is to be measured. If it is known that the voltage is sinusoidal, is there a fast way to perform the measurement that does not rely on averages and provides high accuracy? Finite averaging time is a significant source of rms measurement error for low-frequency signals, but diminishes in effect as frequency is increased (see (5.40)). This does not mean that rms measurements are arbitrarily precise for high-frequency signals, however, because finite averaging time is only one of several sources of error. Other sources of error dominate at high frequencies, where the error due to finite averaging time is minimal. In fact, measurement accuracy generally increases with increasing frequency up to a point, but then begins to fall as frequency is increased further. Manufacturers of measurement devices supply data sheets for their products which specify the cumulative effects of the most significant error sources at various frequencies. In practice, engineers rely on these data sheets to determine the accuracy of a particular measurement.
5.13 Dissipation Derating The ability of a resistor to safely dissipate power generally decreases with increasing temperature. For example, a ½ W resistor that can safely dissipate ½ W when its temperature is 25 C might be able to safely dissipate only ¼ W when its temperature is 120 C. In practice, the power-dissipation ratings of resistors (and other components) are reduced (derated) by a
135
percentage depending upon the expected maximum operating temperature. Derating is based upon information given on manufacturers’ data sheets. For example, Fig. 5.18 shows part of the data sheet (highlights added) for a particular family of thick-film resistors. The derating specification means that a resistor from this family can dissipate at least 35 W at case temperatures up to 25 C, but the power dissipation rating decreases linearly above 25 C, reaching zero at 150 C. Derating specifications also are often presented graphically. For example, the derating specification given in Fig. 5.18 can be presented graphically, as in Fig. 5.19. Example 5.21. Refer to Fig. 5.19. What is the safe dissipation rating for a resistor of that family if the operating (case) temperature is 75 C? Solution: From the graph, the safe dissipation rating is 21 W, or 60% of rated dissipation (at 25 C). A resistor carrying current exhibits self heating due to Joule’s law (P ¼ Irms 2 R). The increase in temperature due to self heating is calculated using the selfheating coefficient ’ defined by ’¼
DT ; DP
(5.41)
where DP is a change in power dissipated and DT is the associated change in temperature. The self-heating coefficient for a resistor is the reciprocal of the slope of the derating characteristic. For temperatures above 25 C, the self-heating coefficient for a resistor having the derating characteristic in Fig. 5.19 is ’¼
150 C 25 C ¼ 3:57 C W1 : 35 W
(5.42)
The operating temperature of a resistor is determined by adding the ambient (environmental) temperature to the temperature increase due to self heating. Once the operating temperature has been determined, the resistor can be derated using the manufacturer’s specifications.
136
5 Work and Power
FEATURES 35 Watt power rating at 25°C SMD - DPAK package configuration Heat resistance to cooling plate: Rth < 4.28°C / W A molded case for environmental protection. Resistor element is electrically insulated from the metal sink tab.
SPECIFICATIONS Material Terminal: Copper Terminal Plating: Lead Free Solder (97% Tin, 3% Silver)
35
100
P ¼ Irms 2 R ¼ ð1:00 AÞ2 ð13:9 OÞ ¼ 13:9W: From (5.42), the self-heating coefficient is 3:57 C W1 . Thus the temperature increase due to self heating is DT ¼ 3:57 C W1 ð10:0 WÞ ¼ 35:7 C: From Fig. 5.19, the maximum operating temperature for which the resistor can safely dissipate 13.9W is approximately T ¼ 100 C. Thus the maximum safe ambient temperature is TA ¼ T DT ¼ 100 C 35:7 C ¼ 76:3 C
Dissipation rating (%)
Example 5.22. A 13.9 O resistor having the derating characteristic in Fig. 5.19 will carry rms current Irms ¼ 1:00 A. What is the maximum safe ambient temperature? Solution: The power that must be safely dissipated by the resistor is
90 28
80 70
21
60 50
14
40 30
7
20
Dissipation rating (W)
Fig. 5.18 Extracted from the data sheet for Ohmite’s TDH series of 35 W thick-film power surface mount resistors (highlights added) (Courtesy of Ohmite Manufacturing Corporation)
Electrical Resistance Range: 0.05 Ω to 10 KΩ other values on request Tolerance: ±1% to ±10% (0.5% on request) Max. Operating Voltage: 350 V Insulation Resistance: 10GΩ min. Power Rating: Depends upon case temperature. See derating curve.
Working Temperature Range: −55°C to +175°C Solder Process: The TDH35P cannot exceed 220°C (260°C for the TDH35H) for more than 10 seconds during soldering process. Derating: 100% @ 25°C to 0% @ 150°C curve referenced to case temperature Dielectric Strength: 1,800VAC Operating Temperature Range: −55°C to +150°C Temperature Coefficient: 10 Ω and above, ±50ppm/°C, referenced to 25°C, ΔR taken at +105°C. Between 1 and 10 Ω, ±(100ppm+0.002 Ω) / °C, referenced to 25°C, ΔR taken at +105°C. For under 10 Ω: 0R6 - 9R9 ..... 100PPM 0R4 - 0R59 ... 150PPM 0R2 - 0R39 ... 250PPM 0R1 - 0R19 ... 500PPM 0R05 - 0R09 = 1000PPM Inductance: less than 20 nanohenries Flatness: less than 0.1mm tolerance
10 0
0 0
25
50 75 100 Temperature (°C)
125
150
Fig. 5.19 Power dissipation derating specification for Ohmite’s TDH series of 35 W thick-film power surface mount resistors, expressed graphically
Example 5.23. A particular application requires a 5O resistor to carry rms current Irms ¼ 2 A in an environment where the ambient temperature is Ta ¼ 50 C. Can a 35W
5.13 Dissipation Derating
137
DP ¼
resistor having the derating characteristic in Fig. 5.19 be used in this application? Solution: The power to be dissipated is
Thus the permissible power dissipation at 100 C is 250 188 mW ¼ 62 mW. (c) Figure 5.20 shows a graph of power-dissipation rating versus temperature.
P ¼ Irms 2 R ¼ ð2 AÞ2 ð5 OÞ ¼ 20 W:
The operating temperature is T ¼ Ta þ DT ¼ 50 C þ 71:4 C ¼ 121:4 C: From Fig. 5.19, the maximum safe dissipation at this temperature is only slightly more than 7W, whereas the required dissipation is 20W. We must look for a resistor having a larger power rating or a smaller self-heating coefficient (or both). Alternatively, we might use some kind of forced cooling, which can be expensive but is often necessary.
Example 5.24. The power-dissipation rating for a certain resistor is 250 mW at 25 C, derated linearly to zero at 125 C. (a) What is the selfheating coefficient for this resistor? (b) What is the power-dissipation rating at 100 C? (c) Draw a graph of permissible power dissipation versus temperature for this resistor. Solution: (a) From (5.41), the self-heating coefficient is ’¼
DT ð125 25Þ C ¼ ¼ 400 CW1 : (5.43) DP ð0:25 0Þ W
(b) For an operating temperature of 100 C, the temperature increase above the rated operating temperature is DT ¼ 100 C 25 C ¼ 75 C and the corresponding decrease in permissible power dissipation is given by:
R ¼ R0 ½1 þ a0 ðT T0 Þ;
(5.44)
where R0 is the resistance at temperature T0 and a0 is the temperature coefficient of resistance (TCR) at that temperature. For present purposes, the temperature of a resistor is given by T ¼ TA þ DT, where TA is ambient temperature and DT is the temperature increase due to self heating, given by DT ¼ ’P ¼ ’Irms 2 R0 , where ’ is the self-heating coefficient and Irms is the rms current through the resistor. Using these relations in (5.44) gives
100
250
80
200
60
150
40
100
20
50
0
0
25
50
75
Temperature (°C)
Fig. 5.20 See Example 5.24
100
0 125
Dissipation rating (mW)
DT ¼ ’P ¼ 3:57 C W1 ð20 WÞ ¼ 71:4 C:
Resistance varies with temperature, and operating temperature is one of the two main sources of uncertainty regarding the resistance of a resistor. The other is the initial tolerance, which is the precision of the nominal resistance at the temperature corresponding to rated power dissipation, often 25 C. Initial tolerance can range from 20% for some carbon-composition resistors down to 0.05% or less for high-precision resistors. From Chapter 2, resistance R as a function of temperature T is given by
Dissipation rating (%)
From (5.42), the self-heating coefficient is ’ ¼ 3:57 C W1 . Thus the temperature increase due to self heating is
DT 75 C ¼ ffi 188 mW: ’ 400 CW1
138
5 Work and Power
R ¼ R0 1 þ a0 TA þ ’Irms 2 R0 T0 :
(5.45)
It follows that the error due to operating temperature is given by DR ¼ R0 a0 TA þ ’Irms 2 R0 T0 :
(5.46)
effective tolerance ¼ 5% þ 7% ¼ 12%: (c) For temperatures above 25 C, the power dissipation must be derated. The permissible dissipation is expressed as a percentage of the 25 C rating by
Thus the effective tolerance (%) is given by DR R0 ¼ b0 þ 100a0 TA þ ’Irms 2 R0 T0 ;
so the percent error due to heating alone is 7%. The effective tolerance is the sum of the error due to heating and the initial tolerance.
b ¼ b0 þ 100
(5.47)
T 25 C ; Tmax ¼ 100 C: D ¼ 100 1 Tmax 25 C
where b0 is the initial tolerance (%). Thus Example 5.25. A certain resistor has resistance R0 ¼ 100 kO 5% and temperature coefficient of resistance a0 ¼ 0:001 C1 , both at 25 C. The power-dissipation rating is 250 mW at 25 C, derated linearly to zero at 100 C. The rms current through the resistor is Irms ¼ 1 mA and the ambient temperature is TA ¼ 40 C. (a) What is the operating temperature of the resistor? (b) What are the resistance and effective tolerance at that temperature? (c) What is the power-dissipation rating at the operating temperature? Solution: (a) The self-heating coefficient is ’¼
DT ð100 25Þ C ¼ ¼ 300 CW1 : DP ð0:250Þ W
The temperature increase DT due to self heating is given by DT ¼ ’ DP ¼ ’Irms 2 R0 ¼ 300 C W1 ð1 mAÞ2 ð100 kOÞ ¼ 30 C: The operating temperature is T ¼ TA þ DT ¼ 40 C þ 30 C ¼ 70 C. (b) The resistance at that temperature is R ¼ R0 ð1 þ a0 T Þ
¼ ð100 kOÞ 1 þ 0:001 C1 ð70 CÞ ¼ 107 kO;
70 C 25 C ¼ 40%: D ¼ 100 1 75 C So the permissible dissipation ð0:40Þð250 mWÞ ffi 100 mW:
is
Example 5.26. A certain 1 W resistor has resistance R ¼ 1 kO 1% at 25 C. The rms amplitude of the current through the resistor is Irms ¼ 8 mA. The self-heating coefficient is ’ ¼ 100 CW1 . The temperature coefficient of resistance at 25 C is a ¼ 5 104 C1 (5000 ppm) and the environmental temperature due to heat from other components ranges from 15 C to 70 C. What is the maximum value of the actual resistance? Solution: The maximum resistance at 25 C is 1kOþ1% ¼ 1:010kO. The corresponding power dissipated by the resistor is P ¼ ð8 mAÞ2 ð1:010 kOÞ ffi 64:6 mW: The temperature increase due to self heating is DTSH ¼ ’P ¼ 100 CW1 ð64:6 mWÞ ¼ 6:46 C and the corresponding increase in resistance due to self heating is
5.14 Power Dissipation in Physical Components and Circuits
DRSH ¼ aDTSH R ¼ 5 104 C1 ð6:46 CÞð1:010 kOÞ ffi 3:26 O: The maximum increase in resistance due to ambient temperature is DRA ¼ aTmax ¼ 5 104 C1 ð70 CÞð1:010kOÞ ffi 35:4O:
139
nin equivalent source are in general meaningless, because the The´venin resistance and the The´venin source are non-physical elements. An expression or value for the power dissipated by an element in a circuit diagram (circuit model) is meaningful only if the element corresponds to a physical component in an associated physical circuit. Alternatively, the power dissipated by a two-terminal circuit is meaningful only if the voltage across and current through the circuit equal the voltage across and current through a physical component modeled by the circuit.
Thus the maximum possible resistance is Rmax ¼ ð1:010kOÞ þ 3:26 O þ 35:4O ffi 1:049 kO: So the actual upper limit on the resistance is 4.9%, not 1%.
Example 5.27. Consider the circuit shown in Fig. 5.21(a), where each resistor corresponds to a physical resistor and the source corresponds to a physical source (e.g., a battery). The average power delivered by the source is given by PS ¼ V0
Exercise 5.20. What is the minimum resistance of the resistor considered in Example 5.26 above? Anticipating and allowing for resistance variation with temperature is an important part of circuit design. In demanding applications, specifying small temperature coefficients and small self-heating coefficients is at least as important as specifying a small tolerance. If sufficiently small temperature coefficients and selfheating coefficients cannot be achieved, some sort of forced cooling is indicated.
Elements in a circuit diagram (model) do not necessarily correspond to physical components in an associated physical circuit.12 Power dissipated by a non-physical element is itself non-physical and often meaningless. For example, the average powers dissipated (individually) by a The´venin equivalent resistance and The´ve-
Review Section 3.1 of Chapter 3.
¼
V0 2 : 4R
2V0 =3 2 V0 V0 2 ¼ ; 12 R 4 R þ 4R=3 3
which is only one-third of the value obtained above. The power delivered by the The´venin
+ V 0 –
2R 4R
4R
+ 2V 0 –
4R / 3 4R
3 source
load
(a) Original circuit
12
This is a meaningful calculation, because the source represents a physical component. In a design context, the calculation tells us that the voltage source must be capable of delivering the power thus calculated. Now consider Fig. 5.21(b), where the circuit has been replaced by its The´venin equivalent. In this case, the power delivered by the The´venin source is given by P0 S ¼
5.14 Power Dissipation in Physical Components and Circuits
V0 4R
Fig. 5.21 See Example 5.27
source
load
(b) Source replaced by Theveinin equivalent
140
5 Work and Power
Va V0 Va þ I0 ¼ 0 R1 R2 ðV0 þ R1 I0 Þ R2 ) Va ¼ ¼ 667 mV: R 1 þ R2
equivalent source is non-physical, and cannot be interpreted as the power required of a physical source. In general, meaningful power calculations must be based upon physical circuit models; i.e., models in which circuit elements correspond to physical components.
The powers P1 ; P2 dissipated by R1 ; R2 , respectively, are ðVa V0 Þ2 ¼ 556 mW; R1 Va 2 P2 ¼ ¼ 4:44 mW: R2
P1 ¼
Exercise 5.21. Show that the power dissipated by the load in Fig. 5.21(b) equals the power dissipated by the load in Fig. 5.21(a). When calculating the power dissipated by a particular physical component, it is permissible to replace the rest of the circuit by the (non-physical) The´venin or Norton equivalent, because doing so does not change the terminal characteristics (the i – v relationship) at the terminals of the component in question.
For the “equivalent” circuit in Fig. 5.22(b), we obtain (current division) I1 ¼
R2 ðI0 þ V0 =R1 Þ R1 ðI0 þ V0 =R1 Þ ; I2 ¼ ; R1 þ R2 R1 þ R2
and so Example 5.28. In the circuit shown in Fig. 5.22(a),
P1 ¼ I1 2 R1 ¼ 8:89mW;P2 ¼ I2 2 R2 ¼ 4:44mW:
I0 ¼ 10 mA; V0 ¼ 500 mV; R1 ¼ 50 O; R2 ¼ 100 O: (1) Calculate the power dissipated by each resistor. (2) Repeat for the “equivalent” circuit shown in Fig. 5.22(b), where the circuit to the left of the resistor R2 is replaced by its Norton equivalent. Compare the computed values and explain. Solution: (1) Applying Kirchhoff’s current law to the circuit in Fig. 5.22(a) gives
R1 V0 +– ref
a I0
I1 R2
(a)
Fig. 5.22 See Example 5.28
V ⇒ I0 + 0 R1
R1
I2 R2
(b)
The power dissipated by R2 is the same for both circuits because the circuit seen by R2 in Fig. 5.22(b) is the Norton equivalent of that seen by R2 in Fig. 5.22(a); that is, the terminal characteristic of the circuit to the left of R2 is the same in both cases. The power dissipated by R1 is different for the two circuits because the circuit seen by R1 in Fig. 5.22(b) is not the Norton equivalent of that seen by R1 in Fig. 5.22(a). In other words, if the resistor R2 in Fig. 5.22(a) represents a physical resistor, then so does the resistor R2 in Fig. 5.22(b), because only the rest of the circuit has been transformed. On the other hand, if the voltage source and the resistor R1 in Fig. 5.22(a) represent a physical source and resistor, then the current source and resistor R1 in Fig. 5.22(b) do not. Do not be misled by the fact that the original resistor and the Norton equivalent resistor are both labeled R1, which means only that the two resistors have the same resistance, not that they are the same physical resistor.
5.15 Active and Passive Devices, Loads, and Circuits
To calculate average and peak power for each component in a circuit, we must know (in general) the instantaneous voltage across and current into the terminals of each component under all operating conditions. In many cases, we must also account for resistance in wires that otherwise might be represented by ideal conductors in a circuit model, and we must know the efficiency with which some components convert electrical energy to the desired form (some is converted to heat); for example, much of the energy delivered to a loudspeaker is converted to acoustic energy, not to heat (the efficiency of a typical highquality loudspeaker is about 70% or smaller).
5.15 Active and Passive Devices, Loads, and Circuits In the discussion that follows, device means physical component, not idealized circuit element. For example, a battery is a physical component, whereas an independent voltage source is an idealized circuit element (which often is a useful model for a battery). Devices often are described as being either active or passive. In common usage, an active device is a device that allows one current or voltage to control another. Transistors are important active devices, as are most integrated circuits. Without active devices, there would be no electronic circuits (and little need for electrical engineers). A device that is not active is a passive device. Most passive devices have only two terminals, whereas active devices have three or more terminals. A resistor is a passive device. An active circuit is a circuit incorporating one or more active devices and which allows some currents or voltages to control others. An audio amplifier is an active circuit because it incorporates active devices and because it allows the current or voltage from (e.g.) a microphone to control the current or voltage delivered to a loudspeaker. The power delivered to the loudspeaker is provided by a power supply, not by the microphone, but is controlled by the current or voltage produced at the terminals of the microphone. A passive circuit is a circuit containing only passive devices. Passive circuits are important components of many larger, active circuits; for example,
141
one or more passive circuits may be needed to establish the conditions under which a transistor can perform as an active device. Thus, although virtually all electrical systems for communication, control, and other applications require active devices and circuits, they also contain a great many passive circuits. The terms load and source are used in various ways in various contexts. Generally, a two-terminal element, device, or circuit is regarded as a load if the average power dissipated by the element, device, or circuit is positive and as a source if the average power dissipated by the element, device, or circuit is negative. When we say that one element, device, or circuit loads a second element, device, or circuit, we mean that the first draws average power from the second; i.e., that the total average power dissipated by the first (the load) is positive and that the total average power dissipated by the second (the source) is negative. When we say that a source is lightly loaded, we mean that the power delivered by the source is a small fraction of the power available from the source. Conversely, the average power delivered by a heavily loaded source is a large fraction of the available power. As an analogy, the engine of a car idling at a traffic light is lightly loaded, whereas the engine of a car pulling a heavy trailer up a steep grade might be heavily loaded. For an electrical example, refer to Fig. 5.23, which shows a source driving a load. For simplicity, the voltage VS is constant. Thus the current I is constant and the average power delivered by the source VS to the load RL is given by PL ¼ IS 2 RL ¼
VS 2 RL ðRS þ RL Þ2
:
From (5.17), the available power is given by PL max ¼
VS 2 ; 4RS
I + V – S
RS
source
Fig. 5.23 Source driving a load
RL
load
142
5 Work and Power
so the fraction of the available power delivered to the load is given by
RS
iL +
a¼
PL PL max
+ –
VS 2 RL
4RS 4RL RS ¼ ¼ : ðRS þ RL Þ2 VS 2 ðRS þ RL Þ2
vL
vS
RL
–
source
If RL ffi RS , then a ffi 1 and the source is heavily loaded. If either RL RS or RL RS , then a 1 and the source is lightly loaded. Loads (two-terminal circuits) also are called active or passive, depending upon whether they require a separate source of power to be effective. An active load is essentially an active device, in the sense that an active load controls (or dissipates) power provided by a supply that is separate from the current or voltage driving the load. In some applications, a dc electric motor is wired such that the armature current is provided by a fixed source and the relatively small field current produced by an electronic circuit controls the speed of the motor. A dc motor operated in this manner is an active load. A passive load requires no separate power source. Whereas the power dissipated by an active load comes partly (or mostly) from a separate power supply, the power dissipated by a passive load comes entirely from the circuit driving the load. Do not attach too much significance to the definitions above of the terms active and passive. The terms are useful and much-used by electrical engineers, but a rigorous definition that would allow us to determine whether any particular circuit is active or passive would be of little value in circuit analysis and design. Also be aware that not all authors are in agreement regarding the definitions.
5.16 Power Transfer and Power Transfer Efficiency Power transfer refers to average power transferred to a load from a source, where the source, the load, or both might be circuits. The power transferred to a load is the power dissipated in the load. Refer to the model shown in Fig. 5.24, where a source drives a load. We wish to express the power transferred to the load in terms of the model parameters vS ; RS ; RL . The power transferred to the load is given by
load
Fig. 5.24 Model used to study power transfer
PL ¼ IL rms RL ¼ 2
¼
RL VS rms 2 ðRS þ RL Þ2
VS rms RS þ RL
2
:
RL (5.48)
We consider power transfer from two perspectives: First, from the perspective of someone who is designing the circuit that will serve as the load and second from the perspective of one who is designing the circuit that will serve as the source. If the source is fixed but the load resistance is variable, the load resistance that maximizes power transfer is that for which " # dPL d RL VS rms 2 ¼0) dRL d RL ðRS þ RL Þ2 ¼
ðRS þ RL Þ2 VS rms 2 2 RL VS rms 2 ðRS þ RL Þ ðRS þ RL Þ4
¼ 0; which yields RL ¼ RS :
(5.49)
If the source is fixed, then the load resistance that maximizes power transfer is equal to the source resistance, provided the source resistance is not zero. Recall from Section 5.5 that the maximum power that can be drawn from a source is called the available power for the source. With reference to Fig. 5.24, the load that draws the available (maximum) power from a source equals the source resistance RS.
5.16 Power Transfer and Power Transfer Efficiency
143 R0
+ – V0
Fig. 5.25 See Exercise 5.22
R0 R
+ –
v0
RT R1
RL
+ –
vT
(a)
source
RL
(b)
Fig. 5.26 A circuit (a) and its The´venin equivalent (b)
Exercise 5.22. Obtain an expression for the maximum power that can be transferred to a load by the source (voltage divider) in Fig. 5.25. If the maximum power is delivered to a load (not shown), what is the power delivered by the source V0? What is the power dissipated in each of R0 and R? Inspection of (5.48) reveals that if the load resistance RL is fixed and the voltage vS is independent of the source resistance, then minimizing the source resistance maximizes the power transferred to the load. From the perspective of one designing a circuit regarded as a source, minimizing the source resistance is desirable, whether or not maximum power transfer is a design goal, because power dissipated in the source is wasted and generates unwanted heat. For example, we may regard an audio amplifier as a source and a loudspeaker as a load. One designing such an amplifier would strive to achieve the lowest possible output resistance to avoid wasting power and generating unwanted heat. But there is a limit to the current an amplifier can provide without suffering damage, so the designer would also call for fuses or circuit breakers to protect the amplifier in case someone attaches a load that would otherwise draw too much current. In general, to maximize the power transferred to a load, we would minimize the source resistance and then make the load resistance equal to the source resistance (assuming the source can provide the theoretical maximum power). But there is a subtle trap one can fall into regarding maximum power transfer. Inspired by the derivation above, one might be tempted to try to achieve maximum power transfer by first finding the The´venin equivalent for a source and then finding the values of the variable circuit parameters for which the The´venin equivalent resistance is minimum. This approach can fail if, as is
usual, both the The´venin resistance and the The´venin voltage depend upon some of the same parameters. In that case, decreasing the The´venin resistance might also decrease the The´venin voltage and decrease, rather than increase, the power delivered to the load. For example, suppose we wish to maximize the power transferred to the fixed load RL by the circuit shown in Fig. 5.26(a). Suppose we proceed by first obtaining the The´venin equivalent shown in Fig. 5.26(b), where
vT ¼
R1 v0 ; R0 þ R1
RT ¼ R0 kR1 ¼
R0 R1 : R 0 þ R1
(5.50)
Suppose further that R0 and R1 represent physical resistors, where R0 is fixed and R1 is somewhat variable. With reference to the The´venin equivalent in Fig. 5.26(b), the analysis above tells us to minimize the The´venin equivalent resistance RT. Because R0 is fixed, the only way to do that is to minimize the resistance R1. However, minimizing R1 minimizes the power transferred to the load. To achieve maximum power transfer in this case, we must maximize R1 which maximizes the The´venin equivalent resistance. Again, keep in mind that the elements of the The´venin (or Norton) equivalent for a source are non-physical, and consequently that the powers dissipated by those elements (individually) might have little or no relation to the power dissipated by elements in the associated physical circuit. In general, finding conditions for maximum power transfer if source parameters are variable requires obtaining a circuit model whose elements correspond to physical components, writing an expression for the power transferred to the load in terms of the variable parameters, and maximizing the power transferred to the load, subject to whatever constraints are imposed on those parameters (e.g., the permissible values of a certain variable resistance might be 10 O R 5kO).
144
5 Work and Power
Problems of this kind generally require numerical methods or techniques based on the calculus of variations, and are beyond the scope of this book. The power transfer efficiency of the circuit in Fig. 5.24 is denoted by and is defined by ¼
PL ; PT
(5.51)
where PL is the power delivered to the load and PT is the total power produced by the voltage source. The difference PT PL is dissipated (wasted) in the source resistance, usually as heat. From (5.48), the power transferred to the load is given by PL ¼
RL VS rms 2 ðRS þ RL Þ2
:
(5.52)
The total power produced by the voltage source is given by PT ¼ IL rms 2 ðRL þ RS Þ VS rms 2 VS rms 2 ¼ ðRL þ RS Þ ¼ : RS þ RL R L þ RS
(5.53)
Therefore the power transfer efficiency is given by ¼
PL RL VS rms 2 RL þ RS RL ¼ ¼ : (5.54) PT ðRS þ RL Þ2 VS rms 2 RL þ RS
To maximize power transfer efficiency, we would minimize the source resistance and maximize the load resistance, possibly subject to a constraint on the minimum power that must be transferred to the load. Here again, elements in the source must correspond to physical components. If vS ; RS are the (non-physical) parameters of a The´venin source model, then minimizing RS by varying the physical parameters upon which RS depends usually will not maximize power transfer efficiency. Exercise 5.23. If the circuit in Fig. 5.24 achieves maximum power transfer, what is the power transfer efficiency of the circuit? Refer again to Fig. 5.25. Equations (5.48) and (5.54) show that reducing the source resistance RS increases both power transfer and power transfer
efficiency. Consequently, if either power transfer or power transfer efficiency is desirable, minimizing the source impedance is a design goal. Achieving maximum power transfer is of interest in a few applications, mainly in the output stages of circuits driving energy-conversion devices, such as motors and loudspeakers, or in the output stages of circuits driving certain signal-transmission components, such as long cables and transmitting antennas. But for most other electronic systems, achieving maximum power transfer efficiency is more important than maximizing power transfer. Power dissipated in a source resistance usually is dissipated as heat that can shorten the lives of nearby components, increase electrical noise, and require extra measures for cooling. Also, power dissipated in the source resistance must be provided by the power supply, even though it is wasted power that contributes nothing to the purpose of the circuit. Moreover, even where actual power transfer is of interest, it is usually the case that a source is being designed to drive a fixed load. Consequently, one designing such a source would try to minimize the source output resistance, thus maximizing both power transfer efficiency and actual power transfer. The development above can be summarized as follows: • If the load is variable and the source is fixed, maximum power transfer is achieved by making the load resistance equal to the (The´venin equivalent) source resistance. • If one or more physical resistors in the source (and, possibly, the load) are variable, we must express the power transferred to the load or power transfer efficiency as a function of the (physical) resistances and find the values of those resistances that maximize that expression. We cannot (in general) simply minimize the The´venin equivalent resistance of the source. In practice, there arise cases where specifications on power transfer or power transfer efficiency cannot be met because of insufficient variability of the source or load parameters; i.e., where the source and load cannot be made equal. In such cases, it often is possible to achieve maximum (or near maximum) power transfer or power transfer efficiency by inserting a transformer or other matching network between the source and the load, as described in Chapter 13.
5.16 Power Transfer and Power Transfer Efficiency
145
However, in many applications, power transfer as a function of load resistance has a broad maximum (is not sharply peaked), so that moderate departure from the ideal (5.49) is acceptable. We can illustrate this remark and other conclusions drawn above as follows. Refer to Fig. 5.27, where a source drives a load RL. We assume the source is fixed and the load is variable and we examine power transfer and power transfer efficiency as functions of load resistance. In this analysis, the source model consisting of vS and RS can be the The´venin equivalent for a more complicated circuit, because we are interested in the power dissipated in the load and not in the powers dissipated in the source model. In Fig. 5.27, let RL ¼ a RS . From (5.48), the power delivered to the load can be expressed as PL ¼
RL VS rms 2 ðRS þ RL Þ2
¼
a VS rms 2 ð1 þ aÞ2 RS
:
(5.55)
The power delivered to the load is maximum for RL ¼ RS and is given by RS
Fig. 5.27 Circuit used for illustrative maximum power calculation (see text)
+ –
vS
RL
maxðPL Þ ¼
RS VS rms 2 ðRS þ RS Þ
2
¼
VS rms 2 : 4 RS
The actual power delivered to the load, expressed as a fraction of the maximum, is given by ! PL a VS rms 2 4 RS ¼ maxðPL Þ VS rms 2 ð1 þ aÞ2 RS ¼
4a ð1 þ aÞ2
:
(5.56)
From (5.54), the power transfer efficiency is given by RL a : (5.57) ¼ ¼ RL þ RS 1 þ a Figure 5.28 shows graphs of the functions defined by (5.56) and (5.57) versus the variable a ¼ RL =RS . The graph of PL = maxðPL Þ can be misleading if not interpreted correctly. Equation (5.49) is derived under the assumption that the source resistance RS is fixed and the load resistance RL is variable, so those assumptions apply also to (5.56) and the graph of PL = maxðPL Þ. That is, although a ¼ RL =RS depends upon both RL and RS, we must regard RS as fixed when interpreting the graph. As expected, the graphs show that maximum power transfer and 50% efficiency occur for a ¼ 1 (for RL ¼ RS ). The peak in power transfer is broad,
1
PL max(PL ) η
0.75
0.5
0.25
0 0.01
0.1
1 RL RS
10
100
Fig. 5.28 Power transfer and power transfer efficiency as functions of load resistance for the circuit shown in Fig. 5.27
146
5 Work and Power
and the actual power delivered to the load exceeds 90% of the maximum possible for (approximately) 0:5 RS < RL < 2 RS . Thus, if 90% of maximum power transfer is acceptable, then it is acceptable to match the load to the source resistance to within a factor of two. Example 5.29. A certain fixed source has source resistance RS ¼ 1kO. The source must deliver 95% or more of the maximum possible power to a load RL. Find the range of acceptable load resistance. Solution: Let RL ¼ a RS . With reference to (5.56), we require 4a ð1 þ aÞ
2
0:95;
which leads to a2 2:21 a þ 1 0: The roots of the quadratic (parabolic) left side are a1 ¼ 0:635; a2 ¼ 1:576; as illustrated by Fig. 5.29. Therefore, 95% or more of the maximum possible power is delivered to a load RL constrained by 0:635 RS RL 1:575 RS or, for RS ¼ 1kO,
a 2 − 2.21a + 1
α
0 0.635
1.575
Fig. 5.29 See Example 5.29
a
vS
+ –
R2 R1
RL
The introductory treatment above of power transfer efficiency ignores certain internal losses that occur in any physical source. Some such losses are incurred even if no load is attached to a source, but are not reflected in a The´venin model for the source. For
vS
+ –
R2 RL
b
b
Fig. 5.30 Internal losses reduce power transfer efficiency (see text)
example, consider the circuits (sources) shown in Fig. 5.30. The two circuits are equivalent at the terminals a–b, but are not internally equivalent. In the circuit on the left, power is dissipated internally (in R1) when the terminals a-b are open (when there is no load), whereas no power is dissipated in the circuit on the right under the same condition. If a load RL is attached to each circuit, the power delivered by the source in the circuit on the left is given by PS1 ¼
VS rms 2 R1 kðR2 þ RL Þ
and for the circuit on the right is given by
635 O RL 1575 O: It is advisable to make a calculation such as this before embarking on a (possibly expensive) load-matching process. It might well be that the marginal gain in power delivered is not worth the cost of matching.
a
PS2 ¼
VS rms 2 : R2 þ RL
The power delivered to the load for each circuit is the same, and is given by PL ¼
VS rms 2 RL ðR2 þ RL Þ2
:
Thus the power transfer efficiency for the circuit on the left is 1 ¼
PL RL ½R1 kðR2 þ RL Þ ¼ PS1 ðR2 þ RL Þ2
5.17 Superposition of Power
and for the circuit on the right by 2 ¼
PL RL ¼ ; PS2 R2 þ RL
which can be written R2 þ RL : 2 ¼ R1 kðR2 þ RL Þ 1 Because R2 þ RL R1 kðR2 þ RL Þ, the power transfer efficiency for the circuit on the right exceeds that for the circuit on the left. The point of the discussion and example above is that the The´venin model for a source can conceal internal losses that can be important to power transfer efficiency. Designing a circuit (source) for maximum power transfer efficiency often involves considerations other than simply minimizing the The´venin equivalent resistance (as seen at the output terminals). The´venin and Norton source models can be good models for physical sources, but are not necessarily so. Limits on the current and power that can be drawn from any particular physical source are not necessarily related as indicated by a linear The´venin model for the source, often because the physical source becomes nonlinear for large terminal current. The The´venin model for a source implies that if we short the terminals of the source, the resulting current is given by iSC ¼ vS =RS . But the physical source so modeled might be unable to deliver that current. As another example, the current any electronic amplifier can deliver is limited, and many such amplifiers (and other circuits), regarded as sources, have very small source resistances. Although a linear model for the amplifier might be valid under or near normal operating conditions, shorting the amplifier terminals can ask for more current (and power) than the amplifier can deliver without damage. For this reason, most modern high-power home audio amplifiers have circuit breakers in the output stage that open if the output current exceeds a pre-set limit.
5.17 Superposition of Power In certain cases, mean squared amplitudes are additive. The only such case we need consider is that of a current or voltage that is expressed as a sum of sinu-
147
soids, no two of which have the same frequency, and one of which may have zero frequency (may be dc). Using (5.25), it can be shown that ½A0 þ A1 cosðo1 tÞ þ A2 cosðo2 t þ y2 Þ þ 2 ¼ A0 2 þ
: A1 2 A2 2 þ þ ; 0 < o1 < o2 < : 2 2 (5.58)
It follows that if the current through a resistor is given by i ¼ I0 þ I1 cosðo1 tÞ þ I2 cosðo2 t þ y2 Þ þ ; 0 < o1 < o2 < ; then the average power dissipated by the resistor is given by I1 2 R I2 2 R P ¼ I0 2 R þ þ þ : 2 2 ¼ I0rms 2 þ I1rms 2 þ I2rms 2 þ R; 0
P¼
(5.61)
Equations (5.59) and (5.61) comprise a special case of the principle of superposition of power. Superposition of power applies where the voltages or currents involved are sinusoids having different, non-zero frequencies. Superposition of power also applies where the currents or voltages involved are derived from physically independent sources and have no dc components, and where a current or voltage is represented by a sum of orthogonal functions.
148
5 Work and Power
Example 5.30. Calculate the average power dissipated by the resistor R2 in the circuit of Fig. 5.31. Solution: The circuit is a current divider. The current through the resistor R2 is given by ix ¼
R1 ðI1 þ i2 þ i3 Þ: R1 þ R2
The currents I1 ; i2 ; i3 have different frequencies, so we may use superposition of power. The average power dissipated by the resistor R2 is
2 R1 I1 rms 2 þ I2 rms 2 þ I3 rms 2 R2 P¼ R1 þ R2 2 R1 1 1 ¼ I0 2 þ ð2 I0 Þ2 þ I0 2 R2 R1 þ R2 2 2 1 1 ¼ I0 2 R2 1þ2þ 9 2 ¼
7 ð5mAÞ2 ð2kOÞ ¼ 19:44 mW 18
Exercise 5.24. Refer to Fig. 5.32, where R1 ¼ 100 O, RL ¼ 5 kO, R0 ¼ 10 kO, i0 ¼ I0 cosðo0 tÞ, and v0 ¼ V0 cosð2o0 tÞ, with
I1
i2
i3
R1
R2
I1 = I0 = 5mA i2 = 2I0 cos(w1t); w1 > 0 i3 = I0 cos(2w1t) R1 = 1kΩ, R2 = 2k Ω
Fig. 5.31 See Example 5.30
v0 + –
i0
R0
R1 RL
i0
R0
R1 + –
v0 Fig. 5.32 See Exercise 5.24
I0 ¼ 2 mA and V0 ¼ 25 V: Obtain an expression for the power dissipated in the load RL. Then calculate the value of the power dissipated in the load. Assume o0 > 0.
5.18 Problems
Section 5.1 is prerequisite for the following problems. P 5.1 A 12-V automobile battery causes a current I ¼ 15A through the automobile headlights for total time t ¼ 1h. Calculate the power dissipated by the headlights, the total charge that passes through the headlights, and the total work done on the headlights during that time. P 5.2 One calorie is the energy required to raise the temperature of 1cm3 of water 1 C. In winter in the midAtlantic states, the average temperature of city water is about 50 F. If electric power is $0.10 per kW h, how much does it cost to heat 40 gal of water to 140 F? P 5.3 An ordinary incandescent lamp converts only about 8% of applied electrical power to visible light. Most of the remaining 92% is infrared radiation. If a 25 W fluorescent lamp provides as much visible light as a 100 W incandescent lamp, what fraction of electrical power applied to a fluorescent lamp is converted to visible light? P 5.4 A 100 W incandescent lamp delivers about 8 W of visible light. A compact fluorescent lamp (CFL) delivers about the same light while consuming 25 W. If a certain light in your home is on 8 h each day, 365 days per year, and if electric power costs $0.10 per kW h, how much would you save per year if you replace the 100 W incandescent lamp with a 25 W CFL? P 5.5 A certain car operating at maximum efficiency can travel about 30 miles on 1 gal of gasoline. If the car were electric (all else equal), how far could it travel on one 12 V, 100 A h battery? P 5.6 The maximum instantaneous electrical power available to many single-family homes built since about 1990 in the US is approximately 190 kW (limited by one or more circuit breakers). If the voltage is sinusoidal and has peak amplitude V0 ¼ 340 V, what
5.18 Problems
149
is the peak amplitude of the (sinusoidal) current when maximum instantaneous power is being delivered? P 5.7 Express the instantaneous power dissipated by each element in the circuit shown in Fig. P 5.1 in terms of the quantities i0 ; v0 ; R1 ; R2 . Section 5.2 is prerequisite for the following problems. P 5.8 The voltage across a certain resistor having resistance R is given by vðtÞ ¼ V0 cosð2p f tÞ: (a) Obtain expressions for the current through the resistor, the instantaneous power dissipated by the resistor, and the total work done on the resistor during an interval 0 t t1 . (b) Let V0 ¼ 155 V, f ¼ 60 Hz, and R ¼ 10 O. Calculate the total work done on the resistor during the interval 0 t 5s. P 5.9 What is the largest constant current to which a 1kO, ½ W resistor should be subjected in ambient air? What is the largest constant voltage? P 5.10 Refer to Fig. P 5.2. (a) Obtain an expression for the power dissipated by the resistor R2. (b) Assume the resistor R1 is fixed and resistor R2 is variable, and obtain an expression for the value of R2 that maximizes the power dissipated by R2. (c) Assume the resistor R2 is fixed and resistor R1 is variable, and obtain an expression for the value of R1 that maximizes the power dissipated by R2. P 5.11 Which resistor in Fig. P 5.3 must have the largest power-dissipation rating? P 5.12 Which resistor in Fig. P 5.4 must have the largest power-dissipation rating?
P 5.13 Refer to Fig. P 5.5, where V0 ¼ 50 V. The power delivered by the source is 90.2 mW, the voltage VA equals 32 V, and R3 ¼ 91 kO. Find R1 and R2. P 5.14 A resistor having resistance R is connected first to the terminals of one resistive linear circuit and then to the terminals of another. In each case, the power dissipated by the resistor is the same. Does this mean the circuits are equivalent? Give at least two examples that justify your answer. P 5.15 Two identical resistors are connected in series. The power-dissipation rating of each is denoted by P. What is the power-dissipation rating of the series connection? P 5.16 Two identical resistors are connected in parallel. The power-dissipation rating of each is denoted by P. What is the power-dissipation rating of the parallel connection? P 5.17 A ½ W, 1 kO resistor is connected in series with a 1 W, 2:2 kO resistor. What are the maximum allowable constant current through and voltage across the series connection? P 5.18 A ½ W, 1 kO resistor is connected in parallel with a 1 W, 2:2 kO resistor. What are the maximum allowable constant current through and voltage across the parallel connection? P 5.19 Refer to Fig. P 5.6, where the circuit parameters V0 and R0 are known and R1 is unknown, but it
+ V 0 –
R
R
R
2R
Fig. P 5.3 See Problem P 5.11
I0
R R
4R 2R
R1
Fig. P 5.4 See Problem P 5.12 i0
v0
+ –
R2 R1
Fig. P 5.1 See Problem P 5.7
A
+ V0
–
Fig. P 5.2 See Problem P 5.10
I0
R1
R2
Fig. P 5.5 See Problem P 5.13
R2
R3
150
5 Work and Power
is known that resistor R1 dissipates power P1. Under what condition(s) is the value of R1 determined uniquely by this information?
Section 5.3 is prerequisite for the following problems. P 5.20 In Fig. P 5.7, the power delivered by the source VS is PS ¼ 200 mW. Use conservation of power to find the resistance R2. P 5.21 Obtain an expression for the total power delivered by the source in the circuit of Fig. P 5.8. P 5.22 In Fig. P 5.9, the power delivered by the source is ps ¼ 2W. Use conservation of power to find the resistance R3. P 5.23 In Fig. P 5.10, the power delivered by the source is 1 W. Use conservation of power to find the resistance R1.
P 5.24 Refer to Fig. P 5.11. The power delivered by the source is 3.16 W and the power dissipated in R1 and R2 is 500 mW. Find the source resistance RS. Assume RS is non-zero. P 5.25 Refer to Fig. P 5.12. A certain 90 V dc motor is 83% efficient, meaning that 83% of the electrical power provided to the motor is delivered to a mechanical load and that 90 V is the maximum voltage that should be applied continuously to the motor terminals. The motor can deliver at most 1.5 hp to a mechanical load without damage. If the motor operates at rated load (1.5 hp) and voltage (VM ¼ 90 V) from a source having open-circuit voltage VS ¼ 100 V, what are the losses (in W) in the source resistance and motor (individually)? P 5.26 Refer to Fig. P 5.13. The total power dissipated in the three resistors is 250 mW and the
RS VS +
R1
–
R0
VS = 15 V, RS = 75 Ω, R2 = 500 Ω
+ V 0 –
Fig. P 5.6 See Problem P 5.19
R2
R1
Fig. P 5.10 See Problem P 5.23 R1
–
IS
RS
+ VS
R1
R2
RS
R2
IS = 5 mA, R1 = 4.7 k Ω
VS = 5 V, RS = 50 Ω, R1 = 100 Ω
Fig. P 5.11 See Problem P 5.24
Fig. P 5.7 See Problem P 5.20 RS
2R VS + – R
+
Fig. P 5.8 See Problem P 5.21
–
2R
V0
+ VM motor and load IM
–
R
Fig. P 5.12 See Problem P 5.25
+ –
V0
I0
R1
R2
R3
I0 = 1 A, R1 = 100 Ω, R2 = 300 Ω
Fig. P 5.9 See Problem P 5.22
I0
R1
R0
R2
I0 = 50 mA, R1 = R2 = 100 Ω
Fig. P 5.13 See Problem P 5.26
5.18 Problems
151
RS
P 5.31 Obtain the time average of each of the following functions:
RL
dc motor
dc generator
VS + –
(a) sin2 ðo tÞ; o>0; ( ) ½1 expðs tÞ; t>0 (b) xðtÞ ¼ ; 0 t0
Fig. P 5.14 See Problem P 5.27 V1 +
–
(c) yðtÞ ¼ ½a cosðo tÞ þ b sinðo tÞ2 ; +
+
–
Fig. P 5.15 See Problem P 5.30
V2
v –
power delivered by the current source is 187.5 mW. Find the resistance R0 and the source voltage V0. P 5.27 A motor drives a generator, as shown in Fig. P 5.14. The efficiency of the motor is 80% and the efficiency of the generator is 90%. This means that the mechanical power delivered to the generator equals 80% of the electrical power delivered to the motor, and that the electrical power delivered to the load RL equals 90% of the mechanical power delivered to the generator. The motor is rated at 90 V and 1 hp, meaning that the mechanical output is 1 hp when the voltage applied to the motor terminals equals 90 V (assuming the source can deliver the required current). Assume that the motor is operating at rated mechanical output, and that the generator is producing 200 V at its output terminals. (a) What is the load resistance RL? (b) What is the electrical power delivered to the motor? (c) If the source voltage is VS ¼ 100 V, what is the electrical loss in the source resistance RS? (d) What is the source resistance? Section 5.6 is prerequisite for the following problems. P 5.28 The open-circuit voltage for a certain source is 10V. The source delivers 8W to a 2O load. Obtain The´venin and Norton models for the source. P 5.29 As a battery discharges, its terminal voltage under load decreases. A certain 24V battery, when fully charged, delivers 20A to a 1O load, but when 50% discharged, delivers 19A to the same load. What is the internal resistance of the battery in each case? P 5.30. Refer to Fig. P 5.15, where the switch changes position at times tn ¼ n DT. Obtain expressions for the average and mean-squared values of v(t).
9 8 2 < t exp t ; t>0 = : (d) zðtÞ ¼ t t ; : 0 t0 P 5.32 By definition, the dc component of a current or voltage is the average of the current or voltage. Thus, the average of v(t) is v ¼ Vdc . The ac component of a current or voltage is what remains if the dc component is removed; i.e. vac ðtÞ ¼ vðtÞ Vdc . Study the definitions just given and then answer the following questions. (a) Does the ac component of a current or voltage have a dc component? (b) Does the dc component of a current or voltage have an ac component? (c) Is a current or voltage the sum of the ac and dc components of the current or voltage? (d) Is the mean-squared amplitude of a current or voltage equal to the sum of the mean-squared amplitudes of the ac and dc components of the current or voltage? (e) Does Ohm’s law hold for the ac and dc components (individually) of the current through and voltage across a resistor? Justify all of your answers. Section 5.7 is prerequisite for the following problems. P 5.33 A sinusoidal current passes through a sample of material having resistance R. Express the peak amplitude of the current in terms of the average power dissipated by the sample. P 5.34 The voltage across a certain 10 O resistor is 500 V for 10 s, then zero for 20 s, then 600 V for 5 s, then off for 60 s. This cycle is repeated indefinitely. What is the average power dissipated by the resistor? P 5.35 The current through a sample of material having resistance R ¼ 1:5k O is given by i ¼ I0 ½3 þ 2 cosðo1 tÞ þ cosðo2 tÞ; 0 < o1 < o2 ; I0 ¼ 25 mA:
152
5 Work and Power
Find the average power dissipated by the sample. P 5.36 When a 12 V battery (a dc source having negligible internal resistance) is connected across a sample of material, the resulting current is I ¼ 2A. When the battery is disconnected and a sinusoidal voltage is applied to the same sample, the average power dissipated is 12 W. What is the peak amplitude of the sinusoidal voltage? P 5.37 The full-load current rating of a dc motor is the average current the motor can draw without overheating. A certain motor has a full-load current rating of 12 A. If the motor is on for 20 s then off for 20 s, then on again for 20 s, then off for 20 s, and so on indefinitely, what is the maximum current the motor can draw during the on times? P 5.38 In Fig. P 5.16, all resistors have the same power-dissipation rating Pmax . (a) Express the maximum permissible value of the source voltage in terms of R and Pmax if the source voltage is a constant given by v0 ¼ V0 . (b) Repeat for v0 ¼ V0 cosðo tÞ.
+ –
R
R
v0
R
2R
Fig. P 5.16 See Problem P 5.38
R i
R R
2R
Fig. P 5.17 See Problem P 5.39
R
+ –
V0
Fig. P 5.18 See Problem P 5.40
R 2R
P 5.39 In Fig. P 5.17, all resistors have the same power-dissipation rating Pmax . (a) Express the maximum permissible value of the source current in terms of R and Pmax if the source current is a constant given by i ¼ I0 . (b) Repeat for i ¼ I0 cosðo tÞ. P 5.40 Refer to Fig. P 5.18. The switch is closed at times t ¼ 0; T; 2T; 3T; , and opened at times t ¼ T=2; 3T=2; 5T=2; . Obtain an expression for the average power dissipated in each element. P 5.41 Figure P 5.19 shows one cycle of a periodic voltage that is applied to a resistor. (a) If the resistance of the resistor is 100 O, what must the power-dissipation rating of the resistor be? (b) If the power-dissipation rating of the resistor is 1 W, what is the minimum allowable value of the resistance?
Section 5.8 is prerequisite for the following problems. P 5.42 Show that Ohm’s law applies to the rms current through a resistor and the rms voltage across the resistor; that is, show that if v is the voltage across and i is the current through a resistor having resistance R, then Vrms ¼ R Irms . Show this in general, not just for constant or sinusoidal current and voltage. Is the relation Vrms ¼ R Irms valid if the resistance R is a function of time? Is the relation Vrms ¼ R Irms valid if the resistance R is a function of the current through the resistor? Justify your answers. P 5.43 Does Kirchhoff’s current law hold for rms currents? Explain. P 5.44 Does Kirchhoff’s voltage law hold for rms voltages? Explain. P 5.45 Can you express the rms amplitude of v ¼ v1 þ v2 in terms of V1 rms and V2 rms ? Do so or explain why not. P 5.46 The ratio of the peak amplitude to the rms amplitude of the ac component of a periodic current or voltage is called the crest factor of the current or voltage. For example, the crest factor for a sinusoidal pffiffiffi waveform is 2. Find the crest factor for each waveform shown in Fig. P 5.20.
5.18 Problems
153
v (V) 50
15
15
10
10
Fig. P 5.19 See Problem P 5.41
−2
12
8
3
x
x X0
X0
T 2
−X0
T 2
t
T
t
T −X0
(a)
(b)
x
x
X0
X0
T 2
t
T −X0
t
T −X0
(c)
(d)
x
x
X0
−X0
t (s) 22
17
X0
T 2 T 8
Fig. P 5.20 See Problem P 5.46, 48
P 5.47 Refer to Problem P 5.46. Can the crest factor of a waveform be less than unity? Explain why or why not. Give two examples of waveforms having unity crest factors. P 5.48 Refer to Problem P 5.46. Assume each periodic waveform shown in Fig. P 5.20 is a voltage across a resistor having resistance R. Express the
T
t −X0
(e)
T 2 3T 8
T
t
(f)
peak power dissipated in terms of the average power dissipated and the crest factor for the waveform. P 5.49 Refer to Fig. P 5.21. Obtain an expression for the average power dissipated by the unspecified element in terms of the rms amplitudes of the terminal current and voltage.
154
5 Work and Power
+
i(t)
v (t) –
R1 i(t) = I0 cos (w t + qi )
v (t) = V0 cos (w t + qv )
+ –
Fig. P 5.21 See Problem P 5.49
R2
v
Fig. P 5.24 See Problem P 5.55 R
4R
2R
3R
+ –
v (t)
Fig. P 5.22 See Problem P 5.52
+
V0
R
i
–
Fig. P 5.25 See Problem P 5.56
i
R1
R2
Fig. P 5.23 See Problem P 5.54
S1
R1
S2
R2
S3
R3
+
P 5.50 For what fraction of a period does the magnitude of a sinusoidal current or voltage exceed the rms amplitude of the current or voltage? P 5.51 A certain 100 O resistor is rated at ½ W. (a) What is the peak amplitude of the largest sinusoidal current the resistor can safely carry? (b) The resistor will be damaged if the instantaneous power dissipated exceeds ½ W for more than 200 ms. If the amplitude of a sinusoidal current through the resistor equals 100 mA, what is the minimum safe frequency of the current? P 5.52 In Fig. P 5.22, R ¼ 1 kO, V0 ¼ 5 V, and vðtÞ ¼ vac ðtÞ þ Vdc , where Vdc ¼ 2 V and vac ðtÞ has peak amplitude 25 V and crest factor 2.2. Find the average power dissipated in the resistor.
Section 5.10 is prerequisite for the following problems. P 5.53 The resistance of a certain transmission line is 0:6 O km1 . The voltage applied to the line is 65 kV (rms). The line delivers 88% of the input power to a 5 kO load. If the line resistance is the only loss mechanism, what is the length of the line? P 5.54 In the circuit shown in Fig. P 5.23, R2 > R1 . (a) Which resistor dissipates more power? (b) Does the answer change if the current source is replaced with a voltage source?
v (t) –
Fig. P 5.26 See Problem P 5.58
P 5.55 In the circuit shown in Fig. P 5.24, R2 > R1 . Which resistor dissipates more power? Does the answer change if the voltage source is replaced with a current source? P 5.56 Refer to Fig. P 5.25. (a) Which resistor dissipates more power than any of the others? (b) What fraction of the total power dissipated is dissipated by the resistor having resistance 4 R? (c) Do the answers to any of the questions above change if the current source is replaced with a voltage source? P 5.57 What is the smallest permissible resistance for a 1 W resistor that must endure a terminal voltage Vrms ¼ 120 V in ambient air? P 5.58 The voltage v(t) at a residential wall outlet (in the US) is a sinusoidal voltage having rms amplitude Vrms ffi 120 V. Refer to Fig. P 5.26, which represents a small space heater having low (S1 closed, S2, S3 open), medium (S1, S2 closed, S3 open), and high (S1, S3 closed, S2 open) settings, which, when the heater is connected to a wall outlet, provide 750, 1000, and 1500 W, respectively. Find the values of R1 ; R2 ; R3 . P 5.59 The standard power-dissipation ratings of ordinary composition resistors are 1=8; 1=4; 1=2; and 1 W: Assume these ratings apply if the resistance
5.18 Problems
Fig. P 5.27 See Problem P 5.60
155
V0
+ R
v(t)
–
equals the specified value and that the rated dissipation must not be exceeded. The standard precisions for such resistors are 1%; 5%; 10%; and 20%. Express the maximum permissible rms current through and the maximum permissible rms voltage across a composition resistor in terms of the precision, the resistance, and the power-dissipation rating. P 5.60 See Problem P 5.59, above. A resistor having nominal resistance R must be able to dissipate the rated power P for any resistance within the specified tolerance; e.g., a 1 kO 10%, ½ W resistor must be able to dissipate ½ W if the actual resistance is anywhere in the range 1 kO 10%. In Fig. P 5.27, the resistor has tolerance 100a (%). Let P denote the power dissipation rating for the resistor and express the actual power dissipated as a fraction of the power dissipation rating if the resistor happens to have its nominal resistance. P 5.61 The temperature coefficient for a certain 1 kO 1% resistor is 0:001 K1 at 25 C. The resistor will be used in an environment where the temperature ranges from 0 C to 80 C. If the voltage across the resistor will be given by vðtÞ ¼ V0 cosð2pf tÞ, where the maximum value of v0 is 15 V, what should be the power-dissipation rating for the resistor? Does the frequency of the voltage matter? P 5.62 Assume that the lifetime of the filament in an incandescent lamp is inversely proportional to the mean squared current through the filament, provided the rms current does not exceed 1.5 A. A certain manufacturer’s 100 W lamp for residential use is advertised to have a lifetime of 1000 h under normal operating conditions (Vrms ¼ 120 V). Approximately how long would the lamp last if the rms amplitude of the applied voltage were 130 V? 110 V? P 5.63 Figure P 5.28 shows a voltage divider driving a resistive load. It is known that the rms amplitude of the source voltage v(t) will not exceed a known value Vrms , but RL is unknown. Specify safe powerdissipation requirements for the resistors R1 ; R2 in terms of R1, R2, and Vrms . P 5.64 The labels on the resistors in the circuit in Fig. P 5.29 denote the resistance and powerdissipation ratings of the resistors. Obtain expressions for safe values of the power-dissipation ratings in
+ –
R1
R2
RL
Fig. P 5.28 See Problem P 5.63
a
2R1, P1
R 2, P 3
V1
R2, P2
3R2, P4
b
Fig. P 5.29 See Problem P 5.64
terms of R1, R2, and Va, where Va is the rms amplitude of the voltage vab. By safe values, we mean dissipation ratings that are safe regardless of the values or relative values of R1 and R2. P 5.65 A certain amplifier drives four 16 O speakers and one 8 O speaker, all in parallel. The The´venin equivalent for the amplifier at the speaker terminals has open-circuit voltage 30 V (rms) and output resistance 1.5 O. (a) What is the power delivered to each speaker? What is the total power delivered by the The´venin source? (b) The owner wishes to add more speakers. What is the maximum number of 16 O speakers that can be added if the amplifier would be damaged by a power load exceeding 250 W? (d) What is the maximum number of 8 O speakers that can be added if the amplifier would be damaged by a power load exceeding 250 W? P 5.66 (Review skin effect in Chapter 2) Wire is rated according to its current-carrying capacity, called ampacity, which depends upon the size (e.g., AWG), material (e.g., copper), insulation, and environment (e.g., force cooled or ambient, in the open or in conduit, etc.). Ordinary plastic-coated AWG 24 copper wire, similar to what you might buy at your local electronics store, has an ampacity of about 3.5 A in the open (in ambient air) and can safely dissipate about 1:25 Wm1 in open air when carrying 3.5 A at dc. If the current is sinusoidal, having rms amplitude 3.5 A, at what frequency would skin effect cause the power dissipation to exceed 1:25 Wm1 by 15% in an AWG 24 copper wire carrying 3.5 A (rms)? P 5.67 Currents encountered in electric-utility substations and in high-power radio and television transmitters can be quite large, and large conductors are
156
5 Work and Power
needed to keep losses to acceptable levels. Because of skin depth, conductors for large ac currents do not need to be solid cylinders, but can often be hollow tubes. Such construction can save a significant amount of expensive copper. Suppose a certain copper conductor must carry a sinusoidal current having rms amplitude Irms and frequency f, and let ’ denote the maximum permissible power loss per unit length. (a) Obtain an expression for the required crosssectional area of the copper conductor. (b) Calculate the required cross-sectional area if the rms amplitude of the current and the allowable loss are 1 kA and 1 Wm1 respectively. What is the diameter of a solid cylindrical wire having that cross-sectional area? (c) If the frequency of the current is 60 Hz, what is the skin depth? What fraction of the cross-sectional area of the solid conductor referred to above is utilized by the current? What is the loss in that case? (d) : What are the inner and outer radii of a hollow copper tube that would meet the loss specification for the specified current and frequency? (e) What is the diameter of a solid copper conductor that meets the loss specification? (f) What is the volume of copper saved per meter by using the tube instead of a solid conductor? What is the percent of the copper saved by using a hollow-tube conductor? P 5.68 Household incandescent lamps are designed to operate at 60 Hz, with an applied voltage of 120 V (rms). The tungsten filament in a 100 W lamp operates at about 3000 K and will burn out almost instantly if the power dissipated exceeds 175 W. The diameter of the filament is approximately 30 mm and the resistivity of tungsten at 3000 K is about 92 mO cm. If the current through the filament is held constant at the design value and the frequency is increased, at what frequency will the lamp burn out? (Note: The answer will be inexact because the filament in an incandescent lamp is tightly and doubly coiled, and the expression given in Chapter 2 for skin depth does not apply to such a geometry. Regard this as a drill problem, not as a real-world design problem.) Section 5.11 is prerequisite for the following problems. P 5.69 If vðtÞ ¼ V0 , where V0 is constant, how would you write an expression for the rms amplitude of v(t)?
P 5.70 If a current is expressed in standard form by iðtÞ ¼ I0 cosðo0 t þ yÞ would you write iðtÞ ¼ pffiffiffi 2 Irms cosðo0 t þ yÞ? P 5.71 A certain plug-in power supply (adapter) is labeled input: 120 VAC 60 Hz 12 W, output: 12 VDC 500 mA. (a) What are the rms and peak amplitudes of the input voltage? (b) What are the allowable effective loads (O) on the adapter? (c) What is the maximum power output? (d) To what does “12 W” refer? P 5.72 The voltage across and current through a certain resistor having resistance R are denoted by v(t) and i(t), respectively, where the positive direction of the current is into the positive terminal. (a) Is it correct to say that R ¼ vðtÞ=iðtÞ? (b) If not, why not, and how would you express the relation between v(t), i(t), and R? Section 5.12 is prerequisite for the following problems. P 5.73 What is the minimum averaging time necessary to measure the rms value of a 1 Hz sinusoidal voltage with 0.1% accuracy? P 5.74 A certain voltmeter measures rms amplitude by averaging, and is advertised not to exceed 0.5% error (magnitude) for a 10 Hz sinusoidal input. Assuming the averaging time is fixed, what is the error at 1 kHz? (Neglect sources of error other than finite averaging time.) P 5.75 : The rms amplitude of a voltage or current is measured by averaging for a finite time. If we start averaging at time zero and stop averaging at time t, the measured rms voltage is given by ffi sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð 1 t 2 0 0 v^rms ðtÞ ¼ v ðt Þdt : t 0 Given a voltage vðtÞ ¼ V0 ½cosð2pf1 tÞþ cosð2pf2 tÞ, with V0 ¼ 5 V, f1 ¼ 100 Hz, and f2 ¼ 1 kHz: (a) What is the true rms amplitude of v(t)? (b) Obtain an expression for the measured rms amplitude v^rms ðtÞ defined above. Plot the measured rms amplitude versus time for 0 t 5=f1 . Show the true rms amplitude on the same graph. (c) Calculate and plot the percent error in the measured rms voltage over the same interval.
5.18 Problems
157
P 5.76 Some inexpensive multimeters measure the rms amplitude of the ac component of a voltage as pffiffiffi vrms ¼ vpeak = 2, where vpeak is the maximum amplitude of the ac component of the voltage. This measurement is correct only for a sinusoidal voltage. Find the measurement error (%) for each of the voltages defined in Fig. P 5.30. Show how to use the crest factors to correct the measured rms amplitude. P 5.77 The accuracy with which a “true rms” multimeter can measure the rms amplitude of a current or voltage depends upon the crest factor of the current or voltage. The error generally increases with increasing crest factor (see Problem P 5.46). Table P 5.1 shows the rated accuracy of the Agilent 3458 multimeter when used to measure the rms amplitude of a sinusoidal voltage and additional errors incurred for various crest factors, where the upper limit on the CF is not included in the range of CF’s; e.g., the additional error for CF ¼ 3 is 0.25%, not 0.15%. What is the accuracy with which this voltmeter can measure the rms value of each wave-
form shown in Fig. P 5.30? For this problem, assume the frequency of a periodic signal equals the reciprocal of the period; i.e., f ¼ T 1 . P 5.78 Discuss the following remark: The rms amplitude of a sinusoid is independent of the frequency of the sinusoid. P 5.79 How long would it take to measure to within 0.1% the rms amplitude of a sinusoid whose frequency is 104 Hz?
Section 5.13 is prerequisite for the following problems.
P 5.80 The power-dissipation rating for a certain resistor is 500 mW at 25 C, derated linearly to zero at 175 C. (a) Draw a graph of permissible power dissipation versus temperature for this resistor. (b) What is the self-heating coefficient for this resistor?
v(t) (V)
v(t) (V)
5
1 10
40
20
80
t(ms)
t(ms)
−5
−1 (a) T = 40 ms
(b) T = 80 ms
v(t) (V)
v(t) (V)
10
5 50
75 100
25
10
20
t (μs)
−10
t(ms) −5
(c) T = 100 μs
(d) T = 20 ms
Fig. P 5.30 See Problem P 5.76 Table P 5.1 Selected accuracy specifications of the Agilent 3458 multimeter (Data Courtesy of Agilent Corporation) (a) Rated Accuracy Frequency Range Maximun Error (%)
10 Hz f < 20 Hz 20 Hz f < 40 Hz 40 Hz f < 100 Hz 100 Hz f < 20 kHz 20 kHz f < 50 Hz 0.40 0.15 0.06 0.03 0.15
(b) Additional Errors for Non-Sinusoidel Inputs Crest Factor Range 1–2 Additional Error (%) 0.00
2–3 0.15
3–4 0.25
4–5 0.40
158
5 Work and Power
100
Percent Rated Dissipation
90 80 70 60 50 40 30 20 10 0 50
75
100
125
150
175 200 T(°C)
225
250
275
300
Fig. P 5.31 See Problem P 5.81
P 5.81 Figure P 5.31 shows the dissipation derating characteristic for a certain family of high-power, wirewound resistors. Estimate the self-heating coefficient for a 20 W resistor from this family. P 5.82 The power-dissipation rating for a certain resistor is 500mW at 25 C. The self-heating coefficient for the resistor is 300 CW1 for temperatures above 25 C. (a) Draw a graph of percent rated dissipation versus temperature for this resistor. (b) What is the power-dissipation rating for this resistor if the temperature of the resistor is 75 C? P 5.83 The temperature coefficient of resistance at 25 C for the resistor described in Problem P 5.80 is 4500 ppm. The resistance of the resistor at 25 C is 1 kO 10%. What is the maximum resistance of this resistor if it carries an rms current of 5 mA in an enclosure where the ambient temperature is 75 C? P 5.84 The temperature coefficient of resistance at 75 C for the family of resistors described in Problem P 5-81 is 450 ppm. A 10O5% resistor from this family is rated at 5 W 75 C and carries an rms current of 500 mA in an enclosure where the ambient temperature is 100 C. What is the range of operating resistances for the resistor? What is the maximum power dissipation? Is the 5 W rating adequate? P 5.85 The temperature coefficient of resistance at 25 C for the resistor described in Problem P 5.82 is 2500 ppm. The resistance of the resistor at 25 C is 1 kO 10% and the resistor must carry an rms current of 15 mA in an enclosure where the ambient temperature is 70 C. What is the derated powerdissipation rating for the resistor?
P 5.86 The resistance of a certain resistor is specified as 2:2 kO 5% at 25 C. The permissible power dissipation at 25 C is 5 W, derated linearly to zero at 225 C. The temperature coefficient of resistance at 25 C equals 450 ppm. (a) Draw a graph of permissible power dissipation versus temperature for this resistor. (b) What is the maximum resistance of this resistor if it carries current 5 mA rms in an enclosure where the ambient temperature is 75 C? P 5.87 The rated power dissipation for a certain 2:2 kO 5% resistor is 5 W at 25 C, derated linearly to zero at 150 C. The temperature coefficient of resistance at 25 C is 400 ppm. (a) What are the nominal, minimum, and maximum resistances of this resistor if it carries an rms current of 5 mA in an enclosure where the ambient temperature is 80 C? (b) What are the high, low, and nominal derated dissipation ratings? P 5.88 A certain resistor has nominal resistance R ¼ 10 kO at 25 C, temperature coefficient of resistance a ¼ 0:002 C1 (2 ppm) at 25 C, and a powerdissipation rating of 250 mW at 25 C, derated linearly to zero at 125 C. The rms current through the resistor is 1.5 mA. If the ambient temperature is 25 C, what is the nominal steady-state temperature of the resistor and what is the nominal resistance at that temperature? P 5.89 The power-dissipation rating for a certain 1kO (nominal) resistor is 500 mW at 25 C, derated linearly to zero at 135 C. (a) What is the powerdissipation rating when the operating temperature is 70 C? If the rms current through the resistor in that case is 10 mA, what is the ambient temperature? (b) If the operating temperature is 85 C and the ambient temperature is 30 C, what is the current through the resistor? P 5.90 A certain resistor has nominal resistance 2.2 kO at 25 C and self-heating coefficient ’ ¼ 180 CW1 . The dissipation derating is linear above 25 C and the temperature of the resistor is 70 C in ambient (25 C) air when the power dissipated equals 250 mW. (a) What is the power-dissipation rating at 25 C? (b) At what temperature does the powerdissipation rating go to zero? (c) What is the operating temperature of the resistor the rms voltage across the resistor is 15V, the ambient temperature is 25 C, and the TCR is 500 ppm? P 5.91 Figure P 5.32 shows a voltage divider, where the resistors R1 ; R2 have identical temperature coefficients and identical self-heating coefficients.
5.18 Problems
159 R1
+
+
V1
Fig. P 5.32 See Problem P 5.91
R2
V2
vS
+ –
+
RS
RL
i
vS RS
RS
RL
vL –
–
–
Fig. P 5.34 See Problem P 5.93
+ V
Fig. P 5.33 See Problem P 5.92
Irms
I1
R1
I2 R1
R2
–
V0 +–
R2
RL
V0 = 10 V, R1 = 10 Ω, R2 = 30 Ω, RL = 100 Ω
Fig. P 5.35 See Problem P 5.94
The ambient temperature for both is 25 C. (a) Obtain an expression for the voltage ratio H ¼ V2 =V1 as a function of the rms current Irms through the resistors. (b) Let a ¼ TCR ¼ 4500 ppm, ’ ¼ self heating R1 ¼ 1 kO; R2 ¼ 2:2 kO coefficient ¼ 200 C W1 , (at 25 C) and construct a graph of the voltage ratio for 0 Irms 20 mA. (c) If you design the voltage divider assuming the resistances have their 25 C values (are independent of the current Irms ), what is the percent error in the voltage ratio for Irms ¼ 20 mA? P 5.92 Figure P 5.33 shows a current divider, where the resistors R1 ; R2 have identical temperature coefficients and identical self-heating coefficients. The ambient temperature for both is 25 C. (a) Obtain an expression for the current H ¼ I2 =I1 as a function of the rms voltage Vrms across the resistors. (b) Let a ¼ TCR ¼ 4500 ppm, ’ ¼ self heating coefficient ¼ 200 C W1 , R1 ¼ 1 kO; R2 ¼ 2:2 kO (at 25 C) and construct a graph of the current ratio for 0 Vrms 10 V. (c) If you design the current divider assuming the resistances have their 25 C values (are independent of the current I), what is the percent error in the current ratio for Vrms ¼ 10 V? Section 5.14 is prerequisite for the following problems. P 5.93 Figure P 5.34 shows a load driven by (the The´venin-equivalent for) a source and the same load driven by an equivalent Norton model for the source. Obtain expressions for the powers dissipated by all elements in each circuit and discuss the results.
I V +–
resistive circuit
Fig. P 5.36 See Problem P 5.95
P 5.94 Refer to Fig. P 5.35. (a) Calculate the power dissipated in each element. Check your result by showing that the total power dissipated (passive sign convention) equals zero. (b) Obtain the The´venin equivalent for the circuit at the terminals a–b (with the load RL removed). Then connect the load to the The´venin equivalent and calculate the power dissipated by each element. Check your result by showing that the total power dissipated (passive sign convention) equals zero. Is the power dissipated by the The´venin resistance equal to the total power dissipated by the resistors R1 ; R2 in the original circuit? Is the power dissipated by the The´venin source equal to the power dissipated by the source in the original circuit? Is the power dissipated by the load the same in each case? (c) Repeat part (b) for the Norton equivalent. (d) Is the power dissipated by the The´venin source equal to that dissipated by the Norton source? Is the power dissipated by the The´venin resistance equal to that dissipated by the Norton resistance? P 5.95 In Fig. P 5.36, the resistive circuit contains only resistors. The rms voltage V and rms current I are known. Your lab partner claims that the maximum power rating required for any resistor in the network does not exceed P ¼ Vrms Irms . (a) Is he correct? (b) Is he still correct if the circuit also contains unknown current or voltage sources?
160
5 Work and Power
Section 5.15 is prerequisite for the following problems. P 5.96 Give three everyday examples of devices containing active circuits. You probably carry at least two such devices. P 5.97 Discuss the following statements: (a) All active devices have three or more terminals. (b) An active circuit must have at least two sources of power, one of which is the input. (c) All energy-conversion devices are active. P 5.98 (Web research) Which of the following devices can be active? (a) Silicon-controlled rectifier (SCR) (b) Thyristor (c) MOSFET (d) JFET (e) BJT (f) Selenium rectifier (g) Solar cell (h) DC electric motor (i) DC generator P 5.99 Classify each of the following as active (contains active components) or passive. (a) Flashlight (b) Microprocessor (c) Portable radio (d) Pocket calculator (e) Digital wristwatch (f) Cell phone (g) Automobile battery P 5.100 Refer to Fig. P 5.37. For each of the following conditions, describe the source as lightly loaded or heavily loaded. (a) vL ðtÞ ffi 0:9 vS ðtÞ (b) jiL ðtÞj jvS ðtÞ=ð2RS Þj for all times t
(c) RL RS (d) RL RS (e) IL rms VL rms IL rms 2 RS (f) vS ðtÞ ffi 1:01 iL ðtÞRS (g) VL rms =IL rms ffi 0:01 RS Section 5.16 is prerequisite for the following problems. P 5.101 The internal resistance of a 9 V alkaline battery is about 2 O. What is the maximum power the battery can deliver to a resistive load? P 5.102 A resistor having resistance R is connected to the terminals of a linear resistive circuit. It is found that the power dissipated by the resistor is P1. An identical resistor is then connected in parallel with the first, after which it is found that the total power dissipated by the two resistors is very nearly 2P1. What can you deduce about the value of the The´venin equivalent resistance, relative to R, for the circuit from these measurements? P 5.103 Repeat Problem P 5.102 for a case where the two powers are approximately equal. P 5.104 A certain linear resistive circuit having a dc output delivers 80 W to an 8 O resistive load, under which condition the power-transfer efficiency is 0.8 (80%). Can you obtain the The´venin equivalent for the circuit from these data? If so, show how. If not, explain why not. P 5.105 A certain linear resistive voltage source having a sinusoidal output can deliver at most 80 W (average) to an 8 O resistive load, under which condition the power-transfer efficiency is 0.8 (80%). Can you obtain the The´venin equivalent for the circuit from these data? If so, show how. If not, explain why not. P 5.106 It is required to maximize the power delivered by two identical batteries to a fixed but unknown resistive load. Is it better to connect the batteries in series or parallel, or does it matter? Justify your answer. P 5.107 Refer to Fig. P 5.38, where the load RL is fixed. (a) Obtain an expression for the power delivered
iL + –
vS
RS
R2
+
vL
I0
– source
Fig. P 5.37 See Problem P 5.100
a
RL
R1
R3
RL b
load
Fig. P 5.38 See Problem P 5.107
5.18 Problems
161
ISC RT
I IR =
IR
VR R
+ + V OC –
R
VR – qR
o
Fig. P 5.39 See Problem P 5.108
VOC
(a)
Ik cosðok t þ yk Þ;
v1
v2
R1
v0 = V0 v1 = V1 cos(w 1t ) v2 = V2 cos(w 2t + q )
R2
0 < w1 < w 2
Fig. P 5.40 See Problem P 5.112
v0
v1 + –
k¼1
+ –
N X
v0
+ –
P 5.112. Refer to Fig. P 5.40. Obtain expressions for the average power dissipated by each resistor. P 5.113 (a) Obtain an expression for the rms amplitude of
+ –
Section 5.17 is prerequisite for the following problems.
V
(b)
+ –
to the load. (b) For what values of the resistances R1 ; R2 ; R3 is the power delivered to the load maximum? (c) Obtain an expression for the The´venin equivalent resistance of the circuit to the left of the terminals a–b. (d) For what value of the The´venin equivalent resistance is maximum power delivered to the load? Discuss. P 5.108 Figure P 5.39 shows a resistor R connected to a The´venin source model and graphs of the terminal characteristics of the source and resistor on the same axes. The The´venin resistance is fixed. What is the relationship between the angles yR ; yT when the power dissipated in the resistor has its maximum value? P 5.109 Show that the power that can be drawn from an independent current source having infinite output resistance is unlimited. P 5.110 Suppose you must design an amplifier that will drive a load whose nominal resistance is 8 O. If maximum power transfer is essential, what value would you attempt to achieve for the output resistance of the amplifier? P 5.111 Even if power transfer from an amplifier to a load is important, why might it be unwise to minimize the output resistance of the amplifier? Hint: What limits the current drawn from the amplifier?
iðtÞ ¼ I0 þ
qT
i0 R1
RL
v0 = V0 cos (w1t ); v1 = V1 cos(w 2t ); i0 = I0 Fig. P 5.41 See Problem P 5.114
2R
2R i0
v0
+ –
v1
RL
+ –
v0 = V0 cos (w1t ) v1 = V1 cos(w 2t + q ) i 0 = I0 0 < w1 < w2
Fig. P 5.42 See Problem P 5.115
where 0 < o1 < o2 < < oN . (b) Suppose N ¼ 3, I0 ¼ 0:5 mA, I1 ¼ 1 mA, I2 ¼ 1 mA, I3 ¼ 1 mA. Calculate the rms amplitude of i(t). What is the average power dissipated if i(t) is applied to a 4.7 kO resistor? P 5.114 Refer to Fig. P 5.41 where 0 < o1 < o2. Obtain an expression for the average power dissipated in the resistor RL. P 5.115 Refer to Fig. P 5.42 where 0 < o1 < o2. Obtain an expression for the average power dissipated in the resistor RL.
.
Chapter 6
Dependent Sources and Unilateral Two-Port Circuits
Circuits are designed and used to establish specified relations among certain currents and voltages, where some currents and voltages are identified as inputs (causes) and others as outputs (effects). Inputs also are called excitations, and outputs also are called responses. Inputs are applied to and outputs are extracted from terminal pairs. A terminal pair to which an input is applied or from which an output is extracted is called a port. To be considered a port, a terminal pair must satisfy Kirchhoff’s current law (current entering one terminal equals current out exiting the other). A two-port circuit is a physical circuit having one input port and one output port. Figure 6.1 shows an abstract representation of a two-port circuit, with v1 or i1 as an input (excitation) and v2 or i2 as the corresponding output (response). A two-port model is a particular, simplified representation of a twoport circuit or device. Whereas a two-port circuit might contain a great many physical components, a two-port model for the circuit contains no more than four elements, and often fewer than four elements; for example, some operational amplifiers,1 available as integrated circuits, contain a dozen or more transistors, but a particular and useful two-port model for an operational amplifier contains only one element. It follows that the circuit diagram for a twoport model bears little or no resemblance to the physical structure of the associated physical circuit or device. Moreover, few, if any components of a two-port model correspond to physical components.
Rather, a two-port model for a physical circuit uses idealized circuit elements to depict relations established by the circuit among the input and output currents and voltages. In other words, a two-port model expresses the terminal characteristics of a two-port circuit, but says nothing about how those terminal characteristics are achieved. The circuit diagram depicting a two-port model is a far cry from a wiring diagram; nonetheless, specifying parameters of a two-port model often is a first step in circuit design. For simplicity, we often refer to a two-port circuit or the associated model as simply a two-port. Also, we usually draw circuit diagrams such that the input port is on the left and the output port is on the right. The two-ports treated in this chapter are composed of only resistors and elements called dependent sources, defined in Section 6.2. Few useful physical circuits are purely resistive, so it might seem that models containing only resistors and sources are of limited value. However, the principles and methods described here are applicable to virtually any linear circuit - even those containing capacitors and inductors.2 In fact, although we have to this point treated only resistive circuits, everything in previous chapters and everything in this chapter are readily extended to circuits that are not entirely resistive. Subsequent chapters describe how. Topics covered in this chapter are prerequisite to fruitful study of subsequent chapters that treat amplifiers and other signal-processing circuits.
1
2
Operational amplifiers are treated in Chapter 7.
Capacitors and inductors are treated in subsequent chapters.
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_6, # Springer ScienceþBusiness Media B.V. 2011
163
164
6 Dependent Sources and Unilateral Two-Port Circuits i1 + v1 –
i1
either an ideal voltage source or an ideal current source, as illustrated by Fig. 6.3, where
i2 + v2
two-port circuit
–
i2
Rout ¼
output port
input port
Fig. 6.1 A representation of a two-port circuit
6.1 Input Resistance and Output Resistance The input resistance Rin of a two-port circuit can be obtained mathematically (from a circuit model) using either an ideal voltage source or an ideal current source, as illustrated by Fig. 6.2, where Rin ¼
V1 : I1
V2 : I2
(6.2)
In general, output resistance depends upon source resistance, so an appropriate source resistance must be attached to the input terminals when making such a calculation. The input and output resistances of a two-port are measured essentially the same way they are calculated, except we might need to account for the internal resistance RS of the (non-ideal) source used to drive the measurement. In Fig. 6.4(a) the input resistance is given in terms of the applied voltage V1 and the measured current I1 by
(6.1)
In general, input resistance depends upon load resistance, so an appropriate load must be attached to the output terminals when making such a calculation. The output resistance Rout of a two-port can be obtained mathematically (from a circuit model) using
Rin ¼
V1 RS ; I1
(6.3)
where the internal resistance RS of the source is subtracted because it is not part of the input resistance. Similarly, in Fig. 6.4(b),
I1 two-port circuit
V1 + –
RL
+ V1 –
I1
Fig. 6.2 Definition of input resistance: Rin ¼ V1 =I1
two-port circuit
RL
two-port circuit
+ V2 –
I2
+ V1 –
two-port circuit
I2 two-port circuit
RS
Fig. 6.3 Definition of output resistance: Rout ¼ V2 =I2
+ V2 –
RS
I1 V1 + –
Fig. 6.4 Measuring input resistance (see (6.3) and (6.4))
RS
two-port circuit
(a)
RL
I1
RS
(b)
RL
6.1 Input Resistance and Output Resistance
165 RS two-port circuit
RS
Fig. 6.5 Measuring output resistance (see (6.5) and (6.6))
+ V 2 –
RS
Fig. 6.6 Output resistance is the The´venin or Norton equivalent resistance
RS
two-port circuit
⇐
Thevenin or i1 Norton Equivalent
two-port circuit
RS
⇐
Thevenin or Norton Equivalent
(b)
R1
(6.4)
R2 R3
Likewise, in Fig. 6.5(a), Rout ¼
V2 RS I2
(6.5)
Fig. 6.7 See Example 6.1
and, in Fig. 6.5(b), Gout ¼
a
I1
1 I2 1 ¼ : Rout V2 RS
I2
(b)
(a)
1 I1 1 ¼ : Rin V1 RS
+ V2 –
two-port circuit
RS
(a)
V1 + –
Gin ¼
I2
(6.6)
R1
+ – V1
R2 R3
RL
ref
Note that V2,I2 in Fig. 6.5(a) are not the same as V2, I2 in Fig. 6.5(b). We can also determine the output resistance of a two-port by finding the The´venin equivalent of the two-port at the output terminals with either a voltage source or current source attached to the input, as illustrated by Fig. 6.6. The output resistance is the The´venin (or Norton) equivalent resistance.
Example 6.1. Obtain an expression for the input resistance of the circuit in Fig. 6.7. Solution: Because we are obtaining input resistance from a circuit diagram (as opposed to a laboratory measurement), we may assume an ideal test source as shown in Fig. 6.8, where we have connected a load RL, as required. The input resistance of the circuit is given by
Fig. 6.8 See Example 6.1
Rin ¼
V1 ¼ I1
V1 R1 : V1 Va
(6.7)
Applying Kirchhoff’s current law to the circuit in Fig. 6.8 gives V a V1 V a Va þ þ ¼ 0: R1 R3 R2 þ RL
(6.8)
which yields Va ¼
R3 ðR2 þRL ÞV1 : (6.9) R3 ðR2 þRL ÞþR1 ðR2 þR3 þRL Þ
Using (6.9) in (6.7) yields
166
6 Dependent Sources and Unilateral Two-Port Circuits
R3 ðR2 þRL ÞþR1 ðR2 þR3 þRL Þ Rin ¼ : (6.10) R2 þR3 þRL We could as well have used series/parallel reduction to find the equivalent resistance at the input terminals, which also is the input resistance. Thus
R1 RS
R2
a
+ V2
R3
– ref
Fig. 6.9 See Example 6.2
R2
Rin ¼ R1 þR3 kðR2 þRL Þ R3 ðR2 þRL Þ (6.11) R3 þR2 þRL R3 ðR2 þRL ÞþR1 ðR2 þR3 þRL Þ ¼ : R2 þR3 þRL
R1
¼ R1 þ
as above. If R2 RL, the input resistance is only weakly dependent upon the load resistance as is evident from the circuit diagram in Fig. 6.7.
Example 6.2. Use the procedure illustrated by Fig. 6.3(b) to obtain an expression for the output resistance of the circuit shown in Fig. 6.7. Solution: Because we are obtaining output resistance from a circuit diagram (as opposed to a laboratory measurement), we may use an ideal dc test source as shown in Fig. 6.9, where Rout
V2 ¼ ¼ I2
V2 R2 : V 2 Va
I2
(6.12)
R3
Fig. 6.10 See Exercise 6.1
Here also, we could have used series/parallel reduction to obtain the equivalent resistance at the output terminals. If R1 RS ; the output resistance is only weakly dependent upon the source resistance.
Exercise 6.1. (a) Use the procedures illustrated by Figs. 6.2(a) and 6.3(a) to obtain expressions for the input resistance and output resistance of the circuit shown in Fig. 6.10. (b) Repeat, using series/parallel reduction. (c) Obtain an expression for the output resistance by attaching a test source to the input and finding the The´venin equivalent at the output terminals.
Kirchhoff’s current law gives Va Va Va V2 þ þ ¼ 0; R 1 þ RS R 3 R2
(6.13)
6.2 Dependent Sources
which yields R3 ðR1 þRS ÞV2 Va ¼ : (6.14) R3 ðR1 þRS ÞþR2 ðR1 þR3 þRS Þ Using this result in (6.12) gives Rout ¼
R3 ðR1 þRS ÞþR2 ðR1 þR3 þRS Þ : (6.15) R1 þR3 þRS
A dependent source is a source whose terminal voltage or terminal current depends upon or is controlled by another voltage or current called the control voltage or control current. The control current or voltage for a dependent source may be in the same circuit as the dependent source or in another circuit remote from the dependent source. It is not necessary that a circuit containing a dependent source be connected to the circuit containing the control current
6.2 Dependent Sources Table 6.1 Dependent (controlled) sources Name Voltage-controlled voltage source (VCVS)
167
Symbol mvc
Terminal characteristic v ¼ mvc
vc
i ¼ gvc
ic
v ¼ ric
ic
i ¼ bic
+ –
i
Control vc
+ v
Voltage controlled current source (VCCS)
–
gvc
i +
Current controlled voltage source (CCVS)
v – ric + –
i +
Current controlled current source (CCCS)
–
b ic
i +
or voltage by a wire, resistor, or other element. For example, you might think of a radio receiver as containing a dependent source controlled by a current or voltage in a distant transmitter. Dependent sources also are called controlled sources, which in many applications is a more descriptive term. We limit our discussion to the four linear dependent sources whose terminal currents or voltages are proportional to one other current or voltage.3 Table 6.1 gives the circuit-diagram symbols and terminal characteristics for these four sources. By convention, and for the present, we assume the parameters m,g,r,b are positive. The sign of the terminal characteristic for a source can be reversed by reversing either the direction of i or the polarity of v on the associated symbol given in Table 6.1. The dimensionless parameters m and b are the intrinsic voltage gain and the intrinsic current gain, respectively, of the associated sources. The parameters r and g are the intrinsic transresistance and intrinsic transconductance, respectively, of the associated
3
v
In general, the source current or voltage can be a linear or nonlinear function of one or more other currents and voltages. More generally, the input or output can be a function of a nonelectrical quantity, such as temperature, pressure, or torque. For example, an electric motor can be regarded as a controlled source whose input is current and whose output is torque.
v
–
sources.4 Transresistance has the dimension of resistance and is expressed in ohms (O). Transconductance has the dimension of conductance and is expressed in siemens (S). Unless confusion is otherwise possible, we omit the adjective intrinsic in references to parameters of dependent sources; e.g., if no confusion is possible, we refer to the intrinsic voltage gain of a VCVS as the voltage gain of the source. But where other like-named quantities are present, we are specific. For example, we might need to refer to the (overall) voltage gain of a circuit that contains a VCVS having intrinsic voltage gain m. A dependent source is a non-physical but useful element for exhibiting a relation between two currents, two voltages, or a current and a voltage. A dependent source exhibits only the relation, not the physical mechanism that establishes the relation. This is similar to using the symbol for a resistor to depict a relation (Ohm’s law) between current through and voltage across the terminals of a resistor. Like the symbol for a dependent source, the symbol for a resistor says nothing about how that relation is established (physically - in a solid). Like a dependent source, a resistor in a circuit
4
These names are contractions of transfer resistance and transfer conductance, respectively.
168
6 Dependent Sources and Unilateral Two-Port Circuits
diagram might be non-physical; e.g., the The´venin equivalent resistance in a model for a two-terminal circuit is in general non-physical. Still, you might think, a resistor is more real than a dependent source, because you can buy resistors, but you cannot find dependent sources listed in electronics catalogs. However, you can buy devices called transistors and operational amplifiers (introduced in the next chapter) that behave like dependent sources under certain operating conditions. Thus it can be argued that dependent sources are as real as resistors, capacitors, and inductors, the main difference being that devices that behave like dependent sources are sold under other names. By and large, analysis of circuits containing dependent sources proceeds in the same manner as analysis of circuits not containing such sources, as illustrated by the following examples.
R bib
– +
(a)
(b)
Fig. 6.11 See Example 6.3
R mv1
+ –
gv1
R
(a)
(b)
Fig. 6.12 See Exercise 6.2
RS
Example 6.3. Transform the circuit shown in Fig. 6.11(a) to the equivalent circuit shown in Fig. 6.11(b). Solution: The transformation proceeds exactly as if the dependent sources were independent sources, following the procedure for converting a Norton source model to a The´venin source model. The Norton and The´venin equivalent resistances are equal and the controlled-source voltage Rbib is obtained by multiplying the controlled-source current bib by the Norton equivalent resistance.
R bib
R
+ v – S
Ro
+ v1
Ri
+ + –
mv1
RL
–
vL
–
Fig. 6.13 See Example 6.4
iS
RS
Ri
a
+ v1 –
Ro gv1
RL
b
Fig. 6.14 See Exercise 6.3
Exercise 6.2. Transform the circuit shown in Fig. 6.12(a) to the equivalent circuit shown in Fig. 6.12(b) (express the transconductance g in terms of the circuit parameters).
Example 6.4. Refer to Fig. 6.13. Obtain an expression for the voltage vL. Solution: By voltage division, vL ¼
RL Ro þ RL
Ri mvS : RS þ Ri
Exercise 6.3. Refer to Fig. 6.14. Obtain an expression for the voltage vab.
Example 6.5. Find the equivalent resistance Req one would measure at the terminals a-b of the circuit shown in Fig. 6.15. Solution: To find the equivalent resistance, we use Ohm’s law. We apply (mathematically) a
6.2 Dependent Sources
169
iin R1
a
+ vin –
R2
a
KVL
R2
biin
R1
b
b
Fig. 6.16 See Exercise 6.4
bi1 i1
Fig. 6.15 See Example 6.5 i1
R1 bi1
vS + –
voltage vin at the terminals a–b, find the resulting current iin , and obtain
a R2 b
Fig. 6.17 See Example 6.6
vin Req ¼ : iin Kirchhoff’s voltage law gives vin þ R1 iin þ ð1 þ bÞR2 iin ¼ 0;
Solution: We use Kirchhoff’s current law to obtain an expression for the open-circuit voltage: i1 bi1 þ
which yields
voc ¼ 0 ) voc ¼ ðb þ 1ÞR2 i1 : R2
But vin ¼ R1 þ ð1 þ bÞR2 : Req ¼ iin Note that if the internal resistance of the dependent current source were infinite, as it is for an independent current source, the equivalent resistance would be R1 + R2, as one might be misled to expect from an inspection of the circuit.
i1 ¼ It follows that
voc ¼ ðb þ 1ÞR2 i1 ¼ ðb þ 1ÞR2
Example 6.6. Refer to Fig. 6.17. Obtain the The´venin equivalent for the circuit at the terminals a–b.
vS voc : R1
Thus the The´venin-equivalent voltage is given by vT ¼ voc ¼
Exercise 6.4. The equivalent or apparent resistance at a terminal pair is given by Req ¼ VS =I; where VS is a voltage applied to the pair and I is the resulting current entering the positive terminal. Find the apparent resistance at the terminals a–b of the circuit shown in Fig. 6.16.
vS voc : R1
ðb þ 1ÞR2 vS : R1 þ ðb þ 1ÞR2
The short-circuit current is given by i1 bi1 þ isc ¼ 0 ) isc ¼ ðb þ 1Þi1 vS ¼ ðb þ 1Þ : R1 Thus the The´venin-equivalent resistance is given by voc ðb þ 1ÞR2 vS vS 1 RT ¼ ¼ ð b þ 1Þ isc R1 þ ðb þ 1ÞR2 R1 ¼
R1 R2 : R1 þ ðb þ 1ÞR2
170
6 Dependent Sources and Unilateral Two-Port Circuits
voltage depends upon a current or voltage produced by the non-zero independent source under consideration. 3. Repeat steps (1) and (2) until all independent sources have been accounted for, then add the individual responses obtained, as usual.
As examples above illustrate, analysis of a circuit containing one or more dependent sources is carried out in the same way as that of a circuit containing no such sources. But there is one caveat: When applying superposition to a circuit containing dependent sources, proceed as follows:
The next example is contrived to illustrate the procedure described above with as little distracting mathematics as possible. Example 6.7. Use superposition to obtain an expression for the voltage vx in the circuit shown in Fig. 6.18(a). Solution: Figure 6.18(b)–(d) illustrate the procedure. Response to v1: We set the other two independent sources (v2 and i1) to zero (replace v2 by a short circuit and i1 by an open circuit). Because v2 ¼ 0, then gv2 ¼ 0 as well, and we replace the dependent current source with an open circuit. The control current ic1 for the dependent voltage source is not necessarily
1. Select an independent source. Set all other independent sources to zero (replace independent voltage sources by short circuits and independent current sources by open circuits). 2. Examine all dependent sources. Set to zero each dependent source whose terminal current or voltage is proportional to the terminal current or voltage of an independent source that was set to zero in step (1) above, but leave all other dependent sources in place. In other words, do not zero a dependent source whose terminal current or R
v2
ic
v1 +
i1
–
+ –
Exercise 6.5. Refer to Fig. 6.14 (Exercise 6.3). Obtain the The´venin equivalent for the circuit at the terminals a–b.
ric
10R
+ –
5R
gv2
+ vx –
(a) original circuit ic1
R v1 +
10R
–
ric1
+ –
+ vx1
5R
– (b) i1, v2 set to zero. v x1 = component of vx due to v1 ic2
R i1
+ –
ric2
10R
+ vx2
5R
– (c) v1, v2 set to zero. vx2 = component of vx due to i1 ic3
10R
v2 + –
R
ric3
+ –
5R
gv2
+ vx3 –
Fig. 6.18 See Example 6.7
(d) v1, i1 set to zero. vx3 = component of vx due to v2
6.2 Dependent Sources
171
Response to v2: Beginning again with the circuit in Fig. 6.18(a), we set v1 and i1 to zero. In this case, gv2 6¼ 0, so we do not set the dependent current source to zero. Figure 6.18(d) shows the resulting circuit. By inspection,
zero, so we do not set the dependent voltage source to zero. Figure 6.18(b) shows the resulting circuit. By inspection, vx3 ¼ ric3
vx1 ¼ ric1
and ic1 ¼
v1 ric1 R
) ic1 ¼
v1 : Rþr
and ic3 ¼
Thus vx1 ¼
rv1 : Rþr
v2 þ vx3 R
Thus
(6.16)
vx3 ¼
Response to i1: Beginning again with the circuit in Fig. 6.18(a), we set v1 and v2 to zero, which makes gv2 zero as well. Thus we replace the independent voltage sources with short circuits and the dependent current source with an open circuit. Here again, the control current ic2 for the dependent voltage source is not necessarily zero, so we do not set the dependent voltage source to zero. Figure 6.18(c) shows the resulting circuit. By inspection,
r ðv2 þ vx3 Þ rv2 ) vx3 ¼ Rþr R
All independent sources have been accounted for, and the complete response is given by vx ¼ vx1 þ vx2 þ vx3 ¼
rðv1 þ Ri1 v2 Þ : Rþr
vx2 ¼ ric2 : Kirchhoff’s current law gives ic2 þ
Exercise 6.6. Use superposition to obtain an expression for the voltage vout in the circuit shown in Fig. 6.19.
ric2 Ri1 i1 ¼ 0 ) ic2 ¼ : R Rþr
Thus vx2 ¼
rRi1 : Rþr
We present the procedure and example above for completeness, but such problems rarely arise in practice. In analysis of electronic systems, superposition is useful mainly where an input (the current or voltage at a single input port) can be modeled using a number of
(6.17)
4R + vx
R
+ R
R i1
– v1 + –
Fig. 6.19 See Exercise 6.6
v2 + –
bi1
2R mvx
+ –
2R
vout –
172
6 Dependent Sources and Unilateral Two-Port Circuits
i1 + v1
i2
input port
–
input subcircuit
+ output port v2 – i2
output subcircuit
i1
Fig. 6.20 Two-port model
independent voltage sources in series or a number of independent current sources in parallel. In most realistic circuit models, internal sources are dependent sources, all of which are controlled by currents or voltages produced by the input. Circuits having independent sources scattered about internally or in which different controlled sources depend upon different independent sources are found mainly in textbooks.
6.3 Linear Two-Port Models Review the introductory discussion at the beginning of this chapter. Because the currents entering and exiting the input port of a two-port circuit are equal and the currents entering and exiting the output port of a two-port circuit are equal, a two-port circuit can be modeled as if it were two separate circuits, called the input subcircuit and the output subcircuit, as shown in Fig. 6.20.5 A two-port model is bilateral if a current or voltage in either subcircuit can give rise to a current or voltage in the other subcircuit. A two-port model is unilateral if currents and voltages in the output subcircuit cannot produce currents or voltages in the input subcircuit. Think of unilateral as meaning one-way, from input to output, but not vice-versa. In a unilateral two-port model, the controlling current or voltage is a current or voltage in the input subcircuit and the controlled current or voltage is a dependent source in the output subcircuit. Exercise 6.7. Under what condition(s) is the circuit shown in Fig. 6.21 unilateral?
R1 + v1 –
Remember that Fig. 6.20 is the structure of a two-port model, not of the associated physical circuit.
+ –
+ –
m2v1
+ v2 –
Fig. 6.21 See Exercise 6.7
For present purposes and for many important applications, unilateral models are sufficient, and we limit our development in this chapter to unilateral models. In addition, we assume that a model contains only dependent sources and resistors (no independent sources).6 Consequently, the model is linear, and every current and voltage in the model is proportional to a current or voltage applied at the input port. From the viewpoint of a source connected to the input port, the input subcircuit in Fig. 6.20 is a load. Because the model is resistive, the load is resistive, and is the equivalent resistance seen at the input port of the model. This resistance is the input resistance of the unilateral two-port model. From the viewpoint of a load attached to the output port, the output subcircuit in Fig. 6.20 is a source. Because the circuit is linear (contains no independent sources), the output (current i2 or voltage v2) is proportional to the input (current i1 or voltage v1). It follows that the output subcircuit is a The´venin or Norton model in which the source is dependent upon the input current or voltage. The The´venin or Norton equivalent resistance at the output port is the output resistance of the unilateral two-port circuit. The input resistance of a unilateral two-port is independent of the load attached to the output terminals, because currents and voltages in the output subcircuit do not give rise to currents or voltages in the input subcircuit. Likewise, because a source attached
6 5
m1v2
R2
Two-port models can be extended to cases where a circuit in question contains independent sources, but we have no need of that generalization in this book.
6.3 Linear Two-Port Models
173 Ro
i1 + v1
mv1
+ –
Ri
i2
–
i1 + v2
+ v1
–
–
Fig. 6.22 Linear models for a unilateral two-port circuit
(b) CCCS model
Ro + –
Ri
i2
i1 + v2 –
ri1
+ v1 –
Example 6.8. Refer to Fig. 6.22. Use source transformation to obtain a CCCS two-port model from the equivalent CCVS model. Solution: The input resistance is unchanged. The output resistance is also unchanged, because the The´venin and Norton equivalent resistances are the same for equivalent circuits. By the usual rules for source transformation, and with reference to Fig. 6.22(b) and (c), we have
i2
Ri
(c) CCVS model
to the output cannot produce a current or voltage in the input subcircuit, the output resistance of a unilateral two-port is independent of what is attached to the input terminals. In other words, the output resistance of a unilateral two-port is independent of the source, and the input resistance of a unilateral two-port is independent of the load. The form of a unilateral two-port model is determined by which of input current or voltage is the controlling quantity and by which of a The´venin or Norton model is used to represent the output subcircuit. Figure 6.22 shows four possible unilateral linear twoport models. Any one of the four models can be made equivalent at its terminals to any resistive unilateral linear two-port circuit. Furthermore, any one of the four models in Fig. 6.22 can be transformed to any other using a source transformation and the relation vT ¼ RT iN provided both the input resistance Ri and the output resistance Ro are non-zero and finite (as they are for any physical circuit). The four models in Fig. 6.22 are equivalent, so choice of a particular model in any application may be based entirely upon ease and objectives of subsequent analysis and interpretation.
+ v2
Ro
–
gv1
Ro
+ v2 –
(d) VCCS model
+ input
Ri
Rf + –
+ v1 –
bi1
Ri
(a) VCVS model i1
i2
v1 –
Ro
output
mv1
Fig. 6.23 See Exercise 6.9
bi1 ¼
ri1 r )b¼ : Ro Ro
Exercise 6.8. Refer to Fig. 6.22. Use source transformation to obtain a VCVS two-port model from the equivalent VCCS model. The components of a two-port model are nonphysical. Neither the input resistance nor the output resistance is necessarily that of a single resistor or even a combination of resistors. Both the input resistance and the output resistance of an electronic circuit, for example, might be determined primarily by properties of a transistor or integrated circuit. Similarly, the dependent source in the output subcircuit is not necessarily associated with any particular physical component. Exercise 6.9. Obtain expressions for the input resistance and the output resistance of the circuit shown in Fig. 6.23. Use two different methods (or test sources) for each.
174
6 Dependent Sources and Unilateral Two-Port Circuits
RS + v – S
Ro1 + v1 –
+ v2 –
+ –m v 1 1
Ri1
Fig. 6.24 Two-ports in cascade
Ro2 Ri2
circuit 1
+ – m v 2 2
VL
–
circuit 2
Ro
6.4 Two-Ports in Cascade As noted above, many complex circuits can be designed and analyzed as interconnections of two-ports. Cascade connections, where one two-port drives or is driven by another, are common in electronic systems. Figure 6.24 shows a cascade connection of two two-ports. Analysis of a cascade connection of unilateral two-ports is straightforward, as illustrated by the following example.
+ RL
+ v1 –
+ –
Ri
mv1
Fig. 6.25 A single VCVS two-port that is equivalent to the cascade connection of two-ports in Fig. 6.24. See Example 6.9
Thus the circuit in Fig. 6.24 can be reduced to the circuit shown in Fig. 6.25, where Example 6.9. Refer to Fig. 6.24. (a) Express the output voltage vL in terms of the source voltage vS and circuit parameters. (b) Reduce the cascade connection to a single equivalent VCVS two-port. Solution: (a) Using voltage division and working from right to left gives RL RL Ri2 m v2 ¼ m m v1 RL þRo2 2 RL þRo2 2 Ri2 þRo1 1 RL Ri2 Ri1 ¼ m m vS RL þRo2 2 Ri2 þRo1 1 Ri1 þRS RL Ri2 Ri1 m m vS : ¼ RL þRo2 Ri2 þRo1 Ri1 þRS 2 1 (6.18)
vL ¼
(b) By inspection, the input resistance and the output resistance of the cascade connection are Ri1 and Ro2, respectively. The open-circuit output voltage is given by (6.18) for RL !1: RL Ri2 voc ¼ lim RL !1 RL þ Ro2 Ri2 þ Ro1 Ri1 m m vS Ri1 þ RS 2 1 Ri2 Ri1 ¼ m m vS Ri2 þ Ro1 Ri1 þ RS 2 1 Ri2 m m v1 : ¼ Ri2 þ Ro1 2 1
m¼
Ri2 m m ; Ri2 þ Ro1 2 1
Ro ¼ Ro2 ; Ri ¼ Ri1 :
Exercise 6.10. (a) Obtain a single VCVS twoport that is equivalent to the cascade connection of two-ports in Fig. 6.26. (b) From the single VCVS model, obtain equivalent VCCS, CCVS, and CCCS models.
6.5 Voltage, Current, and Power Transfer This section describes conditions for optimum transfer of voltage, current, and power from a linear source to a linear load. The source and load can be circuits, in which case the source resistance is the output resistance of the first circuit and the load resistance is the input resistance of the second circuit. We approach our study first from the perspective of one designing a load; e.g., a circuit that is to be driven by another circuit. The source is considered to be fixed, and can be represented by its The´venin or
6.5 Voltage, Current, and Power Transfer
175 RS
i2
+ v1 –
+ v – S
Ri1
Ro1
Ri2
g1v1
circuit 1
Fig. 6.26 See Exercise 6.10
b2i2
Fig. 6.27 Circuit models for analysis of voltage, current, and power transfer
RS
+ vL –
i + v –
source
RL load
(a) Thevenin source model
Norton equivalent, as shown in Fig. 6.27, where the voltage and current transferred from the source to the load are v and i, respectively. We presume the source models represent the same physical source, and therefore are equivalent at their terminals, with vS ¼ RSiS. The resistance RS is the output resistance of the source and is called the source resistance. The resistance RL is the input resistance of the load and is called the load resistance. Although Fig. 6.27 shows the sources as independent sources, they could be dependent. Keep in mind that the elements of the The´venin and Norton equivalent circuits and the input resistance of a load are in general non-physical. We cannot in general change those elements directly. We can only change certain physical parameters upon which the The´venin (or Norton) equivalent for the source and the input resistance of the load depend. The open-circuit source voltage vS is called the available voltage for that source. The short-circuit source current iS is called the available current for the source. This terminology reflects the fact that at any particular time, the available voltage (available current) is the largest (in magnitude) voltage (current) that can be transferred by the source to a resistive load. Exercise 6.11. The current and voltage available from a certain source are I ¼ 2A and V ¼15V, respectively. Draw circuit diagrams
RL
circuit 2
i + – v S
Ro2
iS
RS
source
+ v –
RL load
(b) Norton source model
for the The´venin and Norton models for the source. The available power PA is the maximum average power that can be transferred from the source to a load. From Chapter 5, we know that the available power from a source is the power delivered by the source to a load whose input resistance equals the output resistance of the source. Exercise 6.12. The power available from a certain source having internal (source) resistance RS ¼ 10 O is P ¼ 500 mW. Can you determine both the magnitudes and signs of the available voltage and current?
Exercise 6.13. The current and voltage available from a certain source are I ¼ 2A and V ¼ 15V, respectively. Find the power available from the source.
Exercise 6.14. If the source resistance is halved and the available voltage is unchanged, by what factor is the available power multiplied?
176
6 Dependent Sources and Unilateral Two-Port Circuits
We examine voltage, current, and power transfer from a fixed source to a load in terms of the available voltage vS, the available current iS, and the available power PA. As we show below, efficacy of voltage, current, and power transfer is determined by the relation of the load resistance to the source resistance. The source-load model in Fig. 6.27(a) is a voltage divider. The voltage transferred to the load is given by RL vS RL þ R S RL ¼ ðavailable voltageÞ: RL þ R S
v¼
(6.19)
The voltage transferred to the load is less than the source voltage by the voltage loading factor RL 1: RL þ RS If the load resistance RL approaches infinity, the voltage loading factor approaches unity, and the voltage transferred to the load equals the available voltage. As a practical matter, almost all of the available voltage is transferred to the load if RL RS. To maximize voltage transfer, make the load resistance as large as possible. Note that if the voltage transferred to the load equals the available (open-circuit) voltage, both the current and the power transferred to the load equal zero. Exercise 6.15. If it is required that at least 95% of the voltage available from a source be transferred to a load RL, what are the permissible values of RL =RS ; where RS is the source resistance? The source-load model in Fig. 6.27(b) is a current divider. The current transferred to the load is given by vS RS iS ¼ RS þ RL RS þ RL RS ¼ ðavailable currentÞ: RS þ RL
i¼
(6.20)
The current transferred to the load by the source is less than the available current by the current loading factor
RS 1: R S þ RL If the load resistance RL approaches zero, the current loading factor approaches unity, and the current transferred to the load equals the available current. As a practical matter, almost all of the available current is transferred to the load if RL RS : To maximize current transfer, make the load resistance as small as possible. But keep in mind that all sources are current limited. For each source, there is a maximum load (minimum load resistance) the source can support. If a load demands more current than a source can supply, the source might be damaged or destroyed. For example, if you accidentally lay a wrench across the terminals of an automotive battery, the battery might explode. Note also that if the current transferred to the load equals the available (shortcircuit) current, both the voltage and the power transferred to the load equal zero. Exercise 6.16. If it is required that at least 95% of the current available from a source be transferred to a load RL, what are the permissible values of RL =RS ; where RS is the source resistance? The power available from a source depends upon the source resistance. If the source resistance equals zero, then the available power is unlimited (mathematically). For example, imagine an independent source vS (having zero source resistance) driving a resistive load RL. The average power dissipated by the load, given by P ¼ VSrms 2 =RL ; is unbounded for RL!0. No physical source can provide unlimited power. Moreover, every physical source exhibits internal losses, so the source resistance of any realistic model for a physical source is non-zero. A realistic model for a physical source must contain non-zero source resistance and cannot deliver unlimited power to a load. In the discussion that follows, we assume the source resistance is non-zero. Because no power can be transferred to a load having zero or infinite resistance, we also assume the load resistance is non-zero and finite. With reference to Fig. 6.27, the power transferred to the load is given by
6.5 Voltage, Current, and Power Transfer
PL ¼ Vrms Irms ¼ ¼
RL VS rms 2 ðRL þ RS Þ2
RL VS rms RL þ RS
177
VS rms RL þ RS
:
If RL ¼ 2RS ; approximately 89% of the available power is transferred to the load. (6.21)
Exercise 6.17. What fraction of the power available from a source is transferred to a load whose resistance is half the source resistance?
From Chapter 5, maximum power is transferred from a fixed source to a load if the load resistance RL equals the source resistance RS. Therefore the available power from a source is given by (6.21) with RL ¼ RS: available power ¼ PA ¼
RS VS rms 2 ð2RS Þ2
The available power given by (6.22) is the maximum average power that can be drawn from a source by a load. Again, the available power is unbounded if RS ¼ 0, but that condition is not achieved by any physical source. From (6.22), VS rms 2 ¼ 4RS PA :
(6.23)
Using this relation in (6.21) gives PL ¼ ¼
4RL RS PA ðRL þ RS Þ2 4RL RS ðRL þ RS Þ2
ðavailable power Þ:
(6.24)
If the load resistance is not equal to the source resistance, the power transferred to the load is less than the available power by the factor 4RL RS ðRL þ RS Þ2
1; RS fixed:
(6.25)
To maximize power transfer, make the load resistance equal to the source resistance. As a practical matter (for a resistive source and load), the power transferred to a load has a broad maximum, so this requirement is not very strict. For example, if RL ¼ 2RS (twice the optimum value), then from (6.24) PL ¼
8RS 2 ð3RS Þ2
Exercise 6.18. If it is required that at least 95% of the power available from a source be transferred to a load RL, what are the permissible values of RL =RS ; where RS is the source resistance?
VS rms 2 ¼ : (6.22) 4RS
Equations (6.19), (6.20), and (6.24) quantify penalties for non-optimum transfer of voltage, current, and power from a source to a load. These equations also imply desirable values for or relations between the input resistance of a load and the output resistance of a source, depending upon which of voltage transfer, current transfer, or power transfer is most important. Although the input resistance and the output resistance of a circuit are generally non-physical,7 they are functions of circuit parameters or device parameters that are to some extent dependent upon design and device selection. Knowing desirable values for input resistance and output resistance helps a designer specify components and the configuration of a circuit. The development above assumes a fixed source and variable load. Study of voltage, current, and power transfer from a variable source to a fixed load is more difficult, because such study cannot be based upon only the parameters of the The´venin equivalent for the source. It might appear from (6.19), for example, that voltage transfer is maximized by minimizing the The´venin-equivalent source resistance RS, but that is not necessarily the case because a particular physical parameter (e.g., a physical resistance) might affect both the The´venin-equivalent resistance and the The´venin-equivalent source voltage. For example, consider the circuit shown in Fig. 6.28(a) and the associated The´venin equivalent shown in
ðavailable power Þ
ffi 0:889 ðavailable power Þ:
7
That is, neither is necessarily associated with any particular physical resistor.
178
+ –
6 Dependent Sources and Unilateral Two-Port Circuits
v0
R1
+ v – S
R2
(a)
loading factors or coupling factors. For example, in an electronics textbook, factors appearing in (6.18) (Example 6.9) might be identified as follows:
RS
(b)
Fig. 6.28 A case where minimizing the The´venin-equivalent resistance of a source also minimizes the voltage transferred to a load. See (6.26), (6.27), and related discussion
Fig. 6.28(b). The output (The´venin-equivalent) resistance of the circuit is given by RS ¼ R1 kR2 :
(6.26)
We presume the elements of the circuit in Fig. 6.28(a) are physical. Suppose that R1 is fixed but that R2 is somewhat under our control. We can decrease the output resistance by decreasing R2. However, because the The´venin-equivalent source voltage is given by vS ¼
R2 v0 ; R1 þ R2
(6.27)
decreasing R2 actually decreases the available voltage, in spite of the fact that decreasing R2 decreases the output (The´venin-equivalent) resistance of the source. If R1 is fixed and we wish to maximize any or all of current, voltage, or power transfer, we would make R2 as large as possible even though doing so maximizes the source resistance. To maximize voltage, current, or power transfer from a variable source to a load, we must express the quantity of interest (e.g., load voltage) in terms of actual (physical) circuit parameters and find the values of those parameters for which the quantity is maximized. This is in general a difficult problem, because such expressions can be complicated and there are always constraints on the values of the variable parameters. However (and fortunately), it often is possible to minimize the output resistance of an electronic circuit without reducing the available voltage. In such cases, one almost always attempts to minimize the output (source) resistance, because so doing maximizes all three of voltage transfer, current transfer, and power transfer to a fixed load. The factors that multiply available voltage in (6.19) and available current in (6.20) often are called
vL ¼
Ri1 Ri2 RL m1 m2 v s : Ri1 þ Rs Ri2 þ Ro1 RL þ R02 |fflfflfflfflfflfflfflffl{zfflfflfflfflfflfflfflffl} |fflfflfflfflfflfflfflfflffl{zfflfflfflfflfflfflfflfflffl} |fflfflfflfflfflfflfflffl{zfflfflfflfflfflfflfflffl} input loading
interstage loading
output loading
(6.28) There are three generally undesirable consequences of loading: • The most obvious consequence is attenuation; e.g., as introduced by each loading factor in (6.28). Attenuation is often the least troublesome consequence of loading because attenuation can be made up by amplification. • A more serious consequence of loading is that loading makes the overall relation between the source voltage and the load voltage dependent upon properties of the source and load. If the relation between an input and output depends strongly upon properties of the source or load, a nonlinear source or load can wreak havoc with the intended function of the circuit. • Finally, loading increases the number of parameters that affect the relation between input and output and therefore increases the number of parameters that must be considered by a designer. As a rule, it is desirable to make performance dependent upon as few parameters as possible, and to then specify those parameters as tightly as possible. For these reasons, circuit designers often strive to eliminate loading. We discuss this point further below.
6.6 Transfer Characteristics, Transfer Ratios, and Gain The primary purpose of any particular two-port circuit is to establish a specified relation between the current or voltage available to the circuit from a source and the associated current or voltage transferred from the circuit to a load. For a resistive circuit, the relation is a proportional one. With reference to Fig. 6.29, where the The´venin and Norton source models are equivalent, we may write
6.6 Transfer Characteristics, Transfer Ratios, and Gain
179
RS + v – S
Fig. 6.29 Pertaining to the definitions of transfer characteristics for equivalent sources
iL resistive two-port circuit
RL
iL
+ iS
vL
resistive two-port circuit
RS
–
(a) vS = RSiS
(b) iS = vS / RS
i1 + v S –
Ri
+
v1
Ro
v L ¼ H r iS ;
(6.30)
iL ¼ Hi iS ;
(6.31)
iL ¼ Hg vS :
(6.32)
and
The relations (6.29–6.32) are called transfer characteristics. The parameters Hv ; Hr ; Hi ; Hg are called transfer ratios. For example (6.29) is a voltage transfer characteristic and H4 is the associated transfer ratio. Conversely,
–
Example 6.10. Refer to Fig. 6.30. Find each of the transfer characteristics and transfer ratios defined above. Solution: For the output subcircuit, we have vL ¼ b i1 ðRo kRL Þ
In general, the source current iS and source voltage vS in (6.33) are functions of time, and can equal zero at times. The quantities vL =vS ; vL =iS ; iL =vS ; and vL =iS are undefined at those times. But currents and voltages in resistive circuits are proportional, so whenever any one of vL, vS, iL, and iS is non-zero, all are. Thus the definitions (6.33), where vS and iS must be non-zero, are acceptable. For a resistive two-port model, the transfer ratios Hv, Hr, Hi, Hg are functions of only the model parameters (Ri, Ro and one of m, b, r, and g), the source
vL
resistance RS, and the load resistance RL. In a subsequent chapter, we generalize these definitions to circuits containing other elements (e.g., capacitance and inductance). The transfer characteristics and the transfer ratios for a circuit are always specified or determined with a source and load attached to the circuit. To repeat, a transfer ratio is in general a function not only of the circuit parameters but also of the load resistance RS and the source resistance RS.
Hv ¼
(6.33)
RL
bi1
–
(6.29)
vL iL ; Hg ¼ ; vS 6¼ 0; vS vS iL vL 6 0: Hi ¼ ; Hz ¼ ; iS ¼ iS iS
iL +
RS
Fig. 6.30 See Example 6.10
vL ¼ Hv vS ;
RL
(6.34)
and iL ¼
vL R o b i1 ¼ : iL R o þ R L
(6.35)
For the input subcircuit, i1 ¼
vS Ri þ RS
(6.36)
From the equivalence of The´venin and Norton source models, vS ¼ RS iS :
(6.37)
180
6 Dependent Sources and Unilateral Two-Port Circuits
Voltage Gain: From (6.34) and (6.36),
VL rms ; VS rms
(6.42)
IL rms ; IS rms
(6.43)
VL rms ; IS rms
(6.44)
IL rms Ag ¼ Hg ¼ : VS rms
(6.45)
Av ¼ jHv j ¼
b ðRo kRL Þ vS Ri þ R S b ðRo kRL Þ ) Hv ¼ : Ri þ R S
vL ¼
(6.38)
Current Gain: Ai ¼ jHi j ¼
From (6.37) and the left half of (6.38), b ðRo kRL Þ RS iS R i þ RS b ðRo kRL ÞRS ) Hr ¼ : Ri þ RS
Transresistance:
vL ¼
(6.39)
Ar ¼ jHr j ¼
From (6.35) and (6.36),
Transconductance:
Ro b vS ðRo þ RL ÞðRi þ RS Þ Ro b ) Hg ¼ : ðRo þ RL ÞðRi þ RS Þ
iL ¼
(6.40)
Finally, from (6.37) and the left half of (6.40) Ro b RS iS ðRo þ RL ÞðRi þ RS Þ Ro bRS ) Hi ¼ : ðRo þ RL ÞðRi þ RS Þ
iL ¼
(6.41)
Exercise 6.19. Refer to Fig. 6.31. Find each of the transfer characteristics and transfer ratios defined above. One or more gains are of interest in various applications. These are voltage gain, current gain, transresistance, and transconductance, defined with reference to Fig. 6.29 as follows: Ro
i1 iS
RS
Ri
+ v1 –
+ –
mv1
iL RL
+ vL –
Transconductance has the dimension of conductance (S) and transresistance has the dimension of resistance (O). Voltage gain and current gain are dimensionless. Although (for convenience), we refer to all of the quantities Av, Ai, Ar, Ag as gains, transresistance and transconductance are not gains in the usual sense because current and voltage have different dimensions. It makes no sense to say a current is larger or smaller than some voltage, just as it makes no sense to say a dollar is larger or smaller than a kilogram. Defining the gains in terms of rms amplitudes avoids the minor difficulty that arises when the instantaneous source current or voltage passes through zero, discussed in relation to (6.33). Also, in circuits containing capacitance or inductance,8 the currents and voltages appearing in each definition are not necessarily instantaneously proportional, nor do they necessarily even have the same waveform. Thus gain must be defined (in general) in terms of rms amplitudes.9 To save writing, some omit the rms subscripts when obtaining or presenting expressions for gain, but the rms subscript is implied in such expressions. In the context of this chapter, we could as well use the definitions
8
These elements are treated in subsequent chapters. Peak amplitudes can be (and often are) used if the voltages or currents involved have the same waveform.
9
Fig. 6.31 See Exercise 6.19
6.6 Transfer Characteristics, Transfer Ratios, and Gain
vL iL Av ¼ ; Ag ¼ ; vS 6¼ 0; vS vS iL vL Ai ¼ ; Az ¼ ; iS ¼ 6 0; iS iS
181
ðRo kRL Þ ¼ b ðRo kRL Þ : Av ¼ b R þR R þR
(6.46)
S
Example 6.11. Obtain expressions for (a) the voltage gain, (b) the current gain, (c) the transresistance, and (d) the transconductance of the two-port circuit in Fig. 6.32(a). Solution: We attach a source and a load to the circuit, as shown in Fig. 6.32(b), before seeking the transfer characteristics. (a) By inspection, vLs R S þ Ri
¼
bRo RS : ðRS þ Ri ÞðRo þ RL Þ
(c) From (6.49) Ro kRL vS vL ¼ b R S þ Ri Ro kRL ¼ b R S iS ; R S þ Ri
(6.48)
Thus
and the transresistance is given by Ro kRL Av ¼ b RS RS þ Ri Ro kRL ¼b RS : RS þ R i
(6.49)
and the voltage gain of the circuit is given by
i1 Ri
b i1
Ro
(a) iL
i1 vS +–
RS
+ Ri
b i1
(b)
Fig. 6.32 See Example 6.11
(6.51)
where we have made use of vs ¼ RSiS. The current gain is given by bRo RS Av ¼ ðRS þ Ri ÞðRo þ RL Þ
and
vS vL ¼ b ð R o kR L Þ R S þ Ri Ro kRL vS ¼ b R S þ Ri
(6.50)
i
Ro iL ¼ bi1 Ro þ RL vS Ro ¼ b RS þ Ri Ro þ RL bRo RS iS ¼ ; ðRS þ Ri ÞðRo þ RL Þ
(6.47)
vL ¼ bi1 ðRo kRL Þ:
S
(b) By current division,
which are equivalent to (6.42–6.45) for resistive circuits.
i1 ¼
i
Ro
RL
vL –
(6.52)
(6.53)
(6.54)
182
6 Dependent Sources and Unilateral Two-Port Circuits
In Fig. 6.29, because the source models are equivalent, we have vS ¼ RSiS. Also, by Ohm’s law, vL ¼ RLiL. These relations allow us to express any gain in terms of any other gain.
(d) From (6.51)
vS Ro ; iL ¼ b RS þ Ri Ro þ RL
(6.55) Example 6.12. Express the current gain, transconductance, and transresistance of a circuit in terms of the voltage gain. Solution: From (6.43) and (6.42)
and the transconductance is given by Ag ¼ b ¼
1 Ro RS þ Ri Ro þ RL
bRo : ðRo þ RL ÞðRS þ Ri Þ
Ai ¼
(6.56)
IL rms VLrms =RL RS ¼ ¼ Av : IS rms VSrms =RS RL
(6.57)
From (6.44) Where necessary to avoid confusion, we refer to the gains Av, Ai, Ag, Ar defined by (6.46) as overall gains to distinguish them from the intrinsic gains defined in Section 6.2. For example, when we refer to the current gain of a two-port or circuit, we mean the overall current gain. Thus, the circuit considered in Example 6.11 has intrinsic current gain b and overall current gain Ai given by (6.52). Exercise 6.20. Obtain expressions for the voltage gain, current gain, transconductance, and transresistance of the two-port in Fig. 6.33.
From (6.45) Ag ¼
IL rms VLrms =RL 1 ¼ ¼ Av : VS rms VS rms RL
(6.59)
Ro
Equations (6.57)–(6.59) show that at most one of the four gains Av , Ai , Ag , Ar can be independent of the source and load resistances. For example, if the voltage gain of a circuit is independent of the source and
Fig. 6.33 See Exercise 6.20
Ro1
i1
Ri1
Fig. 6.34 See Exercise 6.21
(6.58)
Exercise 6.23. In each of the following, express the parameter a in terms of the source resistance and load resistance. (a) Ai ¼ aAr , (b) Ag ¼ aAi , (c) Av ¼ aAr , (d) Ai Av ¼ aAr Ag.
i1 – + ri 1
VL rms VL rms ¼ ¼ RS Av : IS rms VSrms =RS
Exercise 6.22. Express the voltage gain, transconductance, and transresistance of a circuit in terms of the current gain.
Exercise 6.21. Obtain expressions for the voltage gain, current gain, transconductance, and transresistance of the circuit shown in Fig. 6.34.
Ri
Ar ¼
+ –
ri1
i2
Ri2
bi2
Ro2
6.7 Power Gain
183
load resistances, then (6.57)–(6.59) show that Ai, Ag, and Ar depend upon the source and load resistances. To pursue this further, we consider the circuit treated in Example 6.11, for which the voltage gain is given by Av ¼ b
ðRo kRL Þ : RS þ Ri
(6.60)
If the input resistance is much larger than the source resistance (if Ri RS) and the output resistance is much smaller than the load resistance (if Ro Rr), then RS þ Ri ffi Ri ; Ro kRL ffi Ro ; and the voltage gain is given to a good approximation by Av ffi b
Ro ; Ri
(6.61)
which is independent of the source and load resistances. But under those same conditions, the current gain, given by (6.52), becomes Ai ffi
bRo RS ; Ri RL
and is strongly dependent upon both the source resistance and the load resistance. The point of the discussion above is the following: The purpose of a two-port circuit is to establish some specified relation between an available current or voltage and the associated load current or voltage. For reasons given at the end of Section 6.5, it usually is desirable that the relation be independent of properties of the source and load. The development leading to (6.61) shows that the voltage gain of the circuit in Fig. 6.32 is independent of the source and load if the input resistance is much larger than the source resistance and the output resistance is much smaller than the load resistance. Although this conclusion is drawn for a specific two-port circuit, it is true in general. The implication for design is that if the voltage gain of a circuit is to be independent of source and load, then make the input resistance of the circuit as large as possible and the output resistance as small as possible. Example 6.13. A certain two-port circuit has input resistance Ri ¼ 100 kO and output resistance Ro ¼ 1 kO. For what values of source and load resistance is the voltage gain of the circuit
approximately independent of the source and load resistances? Solution: Of course the answer depends upon the quantitative meaning of approximately. If we want the effect of source and load resistances on voltage gain to be about 1% or smaller, we might require RS < 0:01Ri ) RS < 1 kO; RL > 100Ro ) RL > 100 kO:
At first glance, it might seem odd that the gains of a two-port circuit are defined such that they are dependent upon properties of the source and load. After all, the source and load are not parts of the circuit under consideration. But a gain of a circuit is essentially a performance measure, and it does make sense for a gain to depend upon how well the circuit makes use of available current, voltage, or power, which depends upon the input resistance relative to the source resistance, and upon how effectively the circuit transfers current, voltage, or power to a load, which depends upon the output resistance relative to the load resistance.
6.7 Power Gain Refer to Fig. 6.29. The power gain of a two-port circuit is defined by Ap ¼ ¼
power delivered to the load available power VLrms 2 =RL 4RS 2 Av : ¼ 2 RL VSrms =ð4RS Þ
(6.62)
From the definition (6.62), it is clear that the power gain of a circuit must be calculated (or measured) with a load attached to the output terminals. Other, equivalent expressions can be obtained from (6.62) and relations among the various gains, such as (6.57–6.59). For example, from (6.57), Av ¼
RL Ai : RS
(6.63)
184
6 Dependent Sources and Unilateral Two-Port Circuits
Using this expression for Av in (6.62) gives AP ¼
4RL 2 Ai : RS
(6.64)
Exercise 6.24. Show that the power gain of a two-port circuit can be expressed in each of the following ways: Ap ¼
4 Ar 2 ¼ 4RL RS Ag 2 ¼ 4Av Ai RL RS
¼ 4Ar Ag :
(6.65)
Exercise 6.25. From (6.62), it appears that increasing the output resistance of a source driving a circuit increases the power gain of the circuit. Discuss whether this is a sensible way to increase power gain.
eardrum ranging from about 1012 W m2(the threshold of hearing) to about 1 W m2 (the threshold of pain). This means, loosely, that the powers of interest at the output of an audio system span 12 orders of magnitude and that the associated currents or voltages of interest span about six orders of magnitude (because power is proportional to the squares of current and voltage). It is impossible to display (graphically) such ranges of power, current, or voltage on a linear scale. Because human hearing, in particular, is approximately logarithmic and has such a large dynamic range, the Bell Telephone Company many years ago adopted a logarithmic measure of relative power called the decibel (dB) defined by P PdB ¼ 10 log ; (6.66) P0 where the logarithm is base ten, P is a power of interest, and P0 is a reference power. The inverse relation is P ¼ P0 10PdB =10 :
Exercise 6.26. From (6.64), increasing the output resistance of the source driving a circuit appears to decrease the power gain of the circuit. Are (6.64) and (6.62) contradictory in this regard? Discuss.
(6.67)
For example, the standard reference for sound intensity is a power density of P0 ¼ 1 pWm2. Thus, if the sound intensity on stage with a rock band is 120 dB, the power density incident on a band member’s eardrum is P ¼ P0 10PdB =10 ¼ P0 1012 ¼ 1Wm2 :
6.8 Gains and Relative Values in Decibels (dB) Virtually all early electronic systems (telephone, radio, television) were intended to produce outputs (sound and pictures) directly perceptible to humans. Human sensory perception is approximately logarithmic. For example, doubling the apparent loudness of an audio system requires squaring the power delivered to the loudspeaker. An analogous statement holds for light incident on the retina. Human sensory perception also has an enormous dynamic range. For example, the dynamic range of human hearing spans about twelve orders of magnitude, corresponding to acoustic power incident on the
Sustained intensity levels above about 90 dB can cause permanent hearing loss. Intensities above about 120 dB can rupture an eardrum instantly. If the power of interest and the reference power P0 are dissipated in the same or equivalent loads, then (6.66) gives
PdB
Vrms 2 =R ¼ 10 log V0rms 2 =R Vrms ¼ 20 log V0 rms
(6.68)
or PdB ¼ 10 log
Irms 2 R I0 rms 2 R
¼ 20 log
Irms : (6.69) I0 rms
6.8 Gains and Relative Values in Decibels (dB)
185
In general, it is incorrect to express the logarithm of a quotient of dimensioned quantities as the difference of logarithms; for example, it is incorrect to write PdB ¼ 20 log
Irms I0 rms
?
¼ 20 log ðIrms Þ 20 log ðI0 rms Þ; because the argument of the logarithm function must be dimensionless. It is true that if both currents are expressed in the same unit (e.g., mA), the result will be correct. Nonetheless, such practice is discouraged because it is prone to error. It also is unnecessary in this age of pocket computers. Since its creation and adoption by the Bell Telephone Company, the decibel has become a standard dimensionless unit for relative power in virtually all electronic systems. In particular, the power gain of a circuit in decibels (dB) is defined by AP dB ¼ 10 logðAP Þ dB:
Power gain in dB can be expressed in terms of voltage gain and current gain. From (6.62) and (6.64), we have 4RS 2 AP dB ¼ 10 log Av RL 4RS (6.71) þ 10 log Av 2 ¼ 10 log RL and 4RL 2 AP dB ¼ 10 log Ai RS 4RL þ 10 log Ai 2 : ¼ 10 log RS
(6.72)
Exercise 6.29. Show that power gain in dB can be expressed as AP dB ¼ 6:02 þ 10 log Ar Ag ¼ 6:02 þ 10 logðAv Ai Þ:
(6.70)
(6.73)
In this case, the reference power is the available power. Example 6.14. The power gain of a certain two-port circuit is 85 dB. What is the actual power gain (not dB)? Solution: From (6.70), 10 logðAP Þ ¼ 85 dB ) Ap ¼ 1085=10 ¼ 100:5 108 ¼ 3:16 108 :
Exercise 6.27. The power gain of a certain two-port circuit is 108 dB. What is the actual power gain (not dB)?
Equations (6.71) and (6.72) inspire the following definitions of voltage gain in dB and current gain in dB: Av dB ¼ 10 log Av 2 ¼ 20 logðAv Þ
(6.74)
Ai dB ¼ 10 log Ai 2 ¼ 20 logðAi Þ:
(6.75)
and
Exercise 6.30. Obtain expressions for the voltage gain, current gain, and power gain, all in dB, for the circuit shown in Fig. 6.35.
i1
Exercise 6.28. The power gain of a certain two-port circuit is 70 dB. If the power delivered to the load is 5 W, what is the available power (from the source)?
iL +
iS
RS
Ri
v1 –
Fig. 6.35 See Exercise 6.30
+
gv1
Ro RL
vL –
186
6 Dependent Sources and Unilateral Two-Port Circuits
6.9 Design Considerations Exercise 6.31. The power gain and voltage gain of a certain two-port are Ap dB ¼ 105dB; Av dB ¼ 84dB: Find the current gain (dB).
Example 6.15. The power gain of a certain two-port circuit equals 50 dB. The source resistance and the load resistance are 15 and 25 O, respectively. Find the voltage gain and the current gain, both in dB and actual value. Solution: From (6.71) and (6.74) 4RS Av dB ¼ AP dB 10 log RL 4 15 ¼ 46:2dB: ¼ 50 10 log 25 From (6.72) and (6.75),
Ai dB
4RL ¼ AP dB 10 log RS 4 25 ¼ 41:8dB: ¼ 50 10 log 15
It follows that the voltage and current gains (not dB) are Av ¼ 102:31 ¼ 204;
Ai ¼ 102:09 ¼ 122:
Transresistance and transconductance are dimensioned and cannot be expressed in dB, because we cannot take the logarithm of a dimensioned quantity. However, transresistance and transconductance can be normalized to dimensionless quantities, using some appropriate resistance or conductance as the normalizing factor, and the normalized quantities can then be expressed in dB. In practice, current gain, voltage gain, and power gain are almost always expressed in dB (as are other ratios, such as an important power ratio called signalto-noise ratio). You should commit the definitions (6.70), (6.74), and (6.75) to memory.
The primary purpose of a circuit is to establish a specified relation between input current or voltage and output current or voltage. The circuit design is guided by the nature of the source, the nature of the load, and what the circuit is intended to achieve. Developments above suggest the following guidelines: • It is almost always desirable to minimize output resistance. Minimizing output resistance maximizes all four of voltage transfer, current transfer, power transfer, and power transfer efficiency to any load having a finite non-zero resistance. Do not exceed current- and power-delivery capabilities of the circuit. • To maximize voltage transfer from a source to a circuit input, maximize the input resistance of the circuit. • To maximize current transfer from a source to a circuit input, minimize the input resistance of the circuit, but do not allow the source current to exceed the maximum current the source can provide. • To maximize power transfer from a source to a circuit input, make the circuit input resistance equal to the source output resistance, but do not exceed the maximum power the source can provide. • To maximize power transfer efficiency from a source to a circuit input, maximize the input resistance of the circuit. Specifying the input resistance of a circuit hinges on which of voltage transfer, current transfer, or power transfer is most important, and that often is determined by properties of the source. Although current and voltage are the primary quantities of interest in circuit analysis and design, they are ultimately only intermediaries that convey other quantities, such as audio, video, and data. Where electric circuits are used to process or transmit such signals, it is often the case that one or the other of current and voltage best represents the quantity of ultimate interest. For example, a mechanical tachometer produces a terminal voltage proportional to the angular velocity of the armature. Consequently, if we are designing an amplifier to scale the output of a tachometer, we might specify a large input resistance to maximize voltage transfer. Here again, large and small are relative terms that must be quantified to be of use in design.
6.10 Problems
187
6.10 Problems In the problems that follow, two-port circuits are drawn with inputs on the left and outputs on the right, unless otherwise labeled.
Section 6.1 is prerequisite for the following problems. P 6.1 Refer to Fig. P 6.1, where R ¼ 1kO, the source resistance RS ¼ 10O, and the load resistance RL ¼ 5kO. Find the input resistance and the output resistance of each two-port shown.
P 6.2 In Fig. P 6.2, the source has open-circuit voltage Voc and short-circuit current Isc. Express the input resistance of the two-port in terms of Voc, Isc, I. P 6.3 In Fig. P 6.3, the source has open-circuit voltage Voc and short-circuit current Isc. Express the input resistance of the two-port in terms of Voc, Isc, V. P 6.4 In Fig. P 6.4, the source has opencircuit voltage Voc and short-circuit current Isc. For R ¼ R1, I ¼ I1. For R ¼ R2 6¼ R1, I ¼ I2 6¼ I1. Obtain an expression for the input resistance of the two-port. P 6.5 In Fig. P 6.5, the source has open-circuit voltage Voc and short-circuit current Isc. For R ¼ R1, V ¼ V1. For R ¼ R2 6¼ R1, V ¼ V2 6¼ V1. Obtain an expression for the input resistance of the two-port.
R
R
R
R
2R
2R
R R (b)
(a)
2R R
R
R
2R R
2R
R
R
R (d)
(c)
2R 2R
R
R
R
R
R
2R
2R R
2R
(e)
(f)
2R
2R
R
4R
Fig. P 6.1 See Problem P 6.1
R
4R
(g)
188
6 Dependent Sources and Unilateral Two-Port Circuits I
R two-port circuit
source
RL
R
a I
VS +–
+ –
R
Fig. P 6.2 See Problem P 6.2
5RI
ref
Fig. P 6.6 See Problem P 6.8 + V –
source
two-port circuit
RL
Rb vS +–
Fig. P 6.3 See Problem P 6.3
+ –
two-port circuit
I
+ R
rie
iL
RS
two-port circuit
RL
Fig. P 6.7 See Problem P 6.9
+ –
V -
vL
RL
Fig. P 6.4 See Problem P 6.4
source
ie
Rc
R source
Re
vS
+ vin –
RL
Fig. P 6.5 See Problem P 6.5
Section 6.2 is prerequisite for the following problems. P 6.6 Show that a resistor can be represented as a dependent voltage source. P 6.7 Show that a resistor can be represented as a dependent current source. P 6.8 : See Fig. P 6.6. (a) Obtain an expression for the voltage Va. (b) Let Vs ¼ 10V, R ¼ 1kO and use a simulation to check your expression (numerically). P 6.9 : Refer to Fig. P 6.7. (a) Express the load voltage vL in terms of the input voltage VS and the circuit parameters. (b) Perform a simulation using Re ¼ 100 O, Rb ¼ 1kO, Rc ¼ 5kO, RL ¼ 2 kO, and r ¼ 2kO. Show that the voltage vL thus obtained agrees with that computed using the relation found in part (a). P 6.10 Refer to Fig. P 6.8. Express the load voltage vL and the load current iL in terms of the available source voltage vS and the circuit parameters RS, m, RL.
+ – mvin
RL
+ vL –
Fig. P 6.8 See Problem P 6.10
P 6.11 Refer to Fig. P 6.9. Obtain the The´venin equivalent circuit at the terminals a–b. Express the The´venin source voltage in terms of the independent source voltage vS. P 6.12 Refer to Fig. P 6.10. Express the voltage vL in terms of the voltage vS and the circuit parameters. No other currents or voltages may appear in the expression. Section 6.3 is prerequisite for the following problems. In problems below, the four models referred to are those defined in Fig. 6.22 in the text. P 6.13 Obtain all four two-port models for the circuit shown in Fig. P 6.11. Express all model parameters in terms of the original circuit parameters. Is the circuit unilateral or bilateral? P 6.14 Figure P 6.12(a) shows the circuit diagram symbol for an npn bipolar junction transistor (BJT).
6.10 Problems
189 c i1
RS + v – S
Fig. P 6.9 See Problem P 6.11
R1
+ – v S
RS
R1
–
+ –
+
R2 m v1
b i1
RL
vL –
Fig. P 6.10 See Problem P 6.12
b i1
i1 R1
b i1
v1 –
i1
+ v1
+
R2
R3
Fig. P 6.11 See Problem P 6.13
The terminals are designated b (for base), c (for collector), and e (for emitter). Figure P 6.12(b) shows a simplified linear ac model for an npn BJT. Such transistors are used as linear amplifiers in three basic configurations, as shown by the circuit diagrams in Fig. P 6.12(c), (d), and (e). For each of the three configurations, replace the transistor with the linear ac model in Fig. P 6.12(b) and express the output in terms of the voltage Vs and the circuit parameters. P 6.15 Refer to Problem P 6.14. Figure P 6.13 shows an alternative equivalent model to that in Fig. P 6.12(a) for a BJT. Repeat problem P 6.14 using the model in Fig. P 6.13. P 6.16 Figure P 6.14 shows a transistor circuit called an emitter-coupled pair. The inputs are the voltages vb1,vb and the output is the voltage vc1 vc2 : Replace each transistor with the CCCS model in Fig. P 6.12(b). The voltage VCC is the supply voltage for the circuit and the terminal labeled VCC is connected to ground (ref) in the small-signal linear model. (The dc supply voltage appears as a short circuit for other currents and voltages.) (a) Obtain an expression for the output in terms of the two input voltages.
Rout + –
mv1
+
a
voc –
isc b
P 6.17 Repeat Problem P 6.16 using the VCCS model in Fig. P 6.13. P 6.18 Find a single equivalent VCVS two-port model for the circuit shown in Fig. P 6.15. Express the parameters of the resultant two-port in terms of the original circuit parameters. P 6.19 Find a single equivalent VCVS two-port model for the circuit shown in Fig. P 6.16. Express the parameters of the resultant two-port in terms of the original circuit parameters. P 6.20 Known independent sources are attached to the terminals of a two-port, as shown in Fig. P 6.17. It is found that i1 ¼ 1mA when v1 ¼5V, that v2 ¼ 100 V when i2 ¼ 0, and that v2 ¼ 125V when i2 ¼ 100 mA. It is known that the two-port is unilateral. Find the parameters of each of the four models for the two-port.
Section 6.4 is prerequisite for the following problems. P 6.21 For each circuit in Fig. P 6.18, obtain expressions for the input resistance and the output resistance. Express the load voltage vL in terms of the voltage vS and the circuit parameters. P 6.22 For each circuit in Fig. P 6.19, obtain expressions for the input resistance and the output resistance. Express the load voltage vL in terms of the voltage vS and the circuit parameters.
Section 6.5 is prerequisite for the following problems. In each problem below, all sources are linear and all two-ports are unilateral, unless the problem implies otherwise.
190
6 Dependent Sources and Unilateral Two-Port Circuits b
c
ib
c
Rb
b
c RS
b ib
+ v – S
e
b
+ e
RB
vout
RC
–
e (a)
(c) common emitter: output = vce
(b)
e RS
e
RS
c
+
b
+ + –
vS
b
RC
Re
+ v – S
vout
vout
c
RB
–
–
Fig. P 6.12 See Problem P 6.14, 15, 16
(e) common collector: output = vec
(d) common base: output = vcb
c
b
Rb
Ri2
gmvbe
Ro2 g2 v1
e
+ v1
Fig. P 6.13 See Problem P 6.15, 17
Ri1
– VCC
RC
Ro1 m1 v1
Fig. P 6.16 See Problem P 6.19
RC c1 c2
b1
+ –
i1 b2
v1 + –
two-port
+ v2
i2
– e1
e2
Fig. P 6.17 See Problem P 6.20
RE ref
Fig. P 6.14 See Problem P 6.16 Ro2 Ri2
+ v2 –
R i1
+ v1 –
+ – m v 2 2
+ –
Fig. P 6.15 See Problem P 6.18
Ro1 m1v1
P 6.23 The output resistance of certain source is 1.2 O. The current available from the source is 1 A. Draw circuit diagrams for The´venin and Norton models for the source and give the values of the model parameters. P 6.24 If the current available from a source is doubled, with all other parameters unchanged, by what factors are the available voltage and power multiplied? P 6.25 If the voltage available from a source is doubled, with all other parameters unchanged, by what factors are the available current and power multiplied? P 6.26 If the output resistance of a source is halved, with all other parameters unchanged, by what
6.10 Problems
191
RS
R4 +
+ vS + –
R1
v1
R2 R3
gv1
–
v2
+ –
–
RL
mv2
+ vL –
(a)
RS vS
+ –
i1 R1
+
R2
+ –
R3
r i1
v2 –
g v2
R4 RL
+ vL –
(b)
RS vS + –
i2
i1 R2
+ –
R1
r i1
R3
b i2
+ R4 RL vL –
(c)
i2 vS + –
RS
+ R1
Fig. P 6.18 See Problem P 6.21
v –
factors are the available voltage, current, and power multiplied? P 6.27 A resistive load RL ¼ 100 O is attached to the terminals of a source whose available current and available power are 5 A and 100 W, respectively. What is the power delivered to the load? What resistive load would draw the available power from the source? P 6.28 The open-circuit voltage and short-circuit current for a certain source are 15 V and 15 mA, respectively. Obtain a graph of the power delivered by the source to a load RL versus the resistance of the load, for 100 O RL 10 kO. Use a logarithmic scale for the load resistance. Section 6.6 is prerequisite for the following problems. P 6.29 Construct a table that gives the voltage gain for each of the four unilateral two-port models (VCVS, VCCS, CCVS, CCCS).
+ –
R2 mv1
R3
b i2
R4
RL
+ vL –
(d)
P 6.30 Find the input resistance and voltage transfer ratio of the circuit shown in Fig. P 6.20. Is the two-port circuit unilateral? Justify your answer. P 6.31 Assume the four two-port models in Fig. P 6.21 are equivalent. Complete the table below, which shows how to convert any model to any other. Convert To ! VCVS From # VCVS m¼m CCVS VCCS m ¼ g Ro CCCS
CCVS
r¼r r ¼ bRo
VCCS
CCCS
g ¼ m=Ro
b ¼ m Ri =Ro
g¼g
b ¼ g Ri b¼b
P 6.32 The input resistance and output resistance of a certain unilateral two-port circuit are 10 kO and 100 O, respectively. When driven by a source having source resistance Rs ¼ 200 O and driving a resistive load RL ¼ 2 kO, the voltage transfer ratio is Hv ¼ 400. Obtain all four unilateral two-port models for the circuit. P 6.33 Figure P 6.22 illustrates measurements made on a certain two-port circuit. With both switches open,
192
6 Dependent Sources and Unilateral Two-Port Circuits
RS
vS + –
+ R1
v1 –
+ –
+
R2
R3
mv1
v2 –
g2 v2
R4 RL
+ vL –
(a) i1 RS
vS + –
i2
R1
b1 i 1
R2
R3
b2 i 2
R4 RL
+ vL –
(b) i1 RS
vS + –
+ R1
b i1
R2
R3
v2 –
gv2
R4 RL
+ vL –
(c)
RS
vS + –
+ R1
Fig. P 6.19 See Problem P 6.22
RS + v – S
v1 –
+ R2 g1v1
R3
v2 –
R4 RL g2 v2
+ vL –
(d)
P 6.35 Obtain expressions for the input resistance, output resistance, voltage gain, current gain, transresistance, and transadmittance for each of the three transistor amplifier circuits in Fig. P 6.12 (Problem P 6.14).
ib Rb
b ib
Rc +
Re
RL
vL –
two-port circuit
Fig. P 6.20 See Problem P 6.30
the voltage V1 is set to 10 mV. When switch S1 is closed, the voltage V1 drops to 9.5 mV, the current I1 becomes 1 mA, and the voltage V2 becomes 1.5 V. When switch S2 is closed, the voltage V2 drops to 1.3 V. Find the output resistance of the source and the three parameters of a VCVS model for the circuit. P 6.34 In a certain application, a two-port circuit will be driven by a source from which the available current and voltage are IA ¼ 25 mA and VA ¼ 500 mV, respectively. The circuit must provide a voltage transfer ratio of at least Hv while driving a resistive load RL ¼ 4 kO. Specify the two-port parameters to the extent possible.
Section 6.8 is prerequisite for the following problems. In problems below, circuit means two-port circuit or a cascade of two or more two-port circuits. P 6.36 Obtain expressions for the power gains of VCVS and CCVS two-port models. Then show that if the models are equivalent, the expressions for power gain are identical. P 6.37 Obtain expressions for the power gains of VCVS and VCCS two-port models. Then show that if the models are equivalent, the expressions for power gain are identical. P 6.38 Obtain expressions for the power gains of VCVS and CCCS two-port models. Then show that if the models are equivalent, the expressions for power gain are identical.
6.10 Problems
193 i1 + Ri
+ –
v1 +
Ro
Ri
mv1
(a)
(b)
i1
+ v1
Ri
g v1
+
Fig. P 6.21 See Problem P 6.31
Ri
Ro
Ro
b i1
+ –
(c)
Ro ri1
(d)
S1
S2
+ V V1
source
A
Fig. P 6.22 See Problem P 6.33
+ V2 V
two-port circuit
RL = 5 kΩ
I1
RS
R4
i2 + R1
v1
g v1
–
RS
R2
R3
+ –
Fig. P 6.23 See Problem P 6.39
vS +–
RL
r i2
–
R4
i1 + R1
R2
bi1
R3
v1
+ –
Fig. P 6.24 See Problem P 6.40
vS + –
–
mv1
RS
Fig. P 6.25 See Problem P 6.41
RL
+ vL –
R4 +
vS + –
+ vL
R1
P 6.39 (a) Obtain an expression for the power gain of the circuit in Fig. P 6.23. (b) Let RS ¼ 50 O; R1 ¼ R2 ¼ R3 ¼ 10 kO; R4 ¼ 100 O; RL ¼ 5 kO; g ¼ 10 mS; r ¼ 8 kO and express the power gain in dB. P 6.40 (a) Obtain an expression for the power gain of the circuit in Fig. P 6.24. (b) Let RS ¼ 50 O; R1 ¼ R2 ¼ R3 ¼ 10 kO; R4 ¼ 100 O; RL ¼ 5 kO; b ¼ 100; m ¼ 50 and express the power gain in dB. P 6.41 (a) Obtain an expression for the power gain of the circuit in Fig. P 6.25. (b) Let RS ¼ 50 O; R1 ¼ R2 ¼ R3 ¼ 10 kO; R4 ¼ 100 O; RL ¼ 5 kO; m1 ¼ 50; m2 ¼ 25 and express the power gain in dB.
v1 –
+ –
R2 m1 v1
+ R3
v2 –
+ –
m2 v2
RL
+ vL –
P 6.42 (a) Obtain an expression for the power gain of the circuit in Fig. P 6.26. (b) Let RS ¼ 50O; R1 ¼ R2 ¼ R3 ¼ 10kO; R4 ¼ 100O; RL ¼ 5kO; m ¼ 75; r ¼ 20kO and express the power gain in dB. P 6.43 A certain circuit has input resistance Rin ¼ 20 kO; output resistance Rout ¼ 100 O; and no-load voltage gain m ¼ 200. The circuit is driven by a source having output resistance RS ¼ 50 O and available power P ¼ 15 W. The circuit is to drive a resistive load RL. (a) Obtain symbolic expressions for the current gain, voltage gain, transresistance, transadmittance, and power gain of the circuit. (b) Find the
194
6 Dependent Sources and Unilateral Two-Port Circuits RS + vS +–
Fig. P 6.26 See Problem P 6.42
R1
Av ¼
Rin Rin þ RS
v1 –
value of the load resistance RL that maximizes the current gain and express the current gain in dB for that load. (c) Find the value of the load resistance RL that maximizes the voltage gain and express the voltage gain in dB for that load. (d) Find the value of the load resistance RL that maximizes the normalized transresistance Ar/RL and express the normalized transresistance in dB for that load. (e) Find the value of the load resistance RL that maximizes the normalized transconductance AgRL and express the normalized transconductance in dB for that load. (f) Find the value of the load resistance RL that maximizes the power gain and express the power gain in dB for that load. P 6.44 Repeat Problem P 6.43 for a circuit having input resistance Rin ¼ 1 kO; output resistance Rout ¼ 50 O; and no-load voltage gain m ¼ 1; 000: The circuit is driven by a source having output resistance RS ¼ 20 kO and available current IS ¼ 100 mA: The circuit is to drive a resistive load RL. P 6.45 Repeat Problem P 6.43 for a circuit having input resistance Rin ¼ 1 MO; output resistance Rout ¼ 30 O; and no-load voltage gain m ¼ 500: The circuit is driven by a source having output resistance RS ¼ 1 kO and available voltage VS ¼ 25 mV: The circuit is to drive a resistive load RL. P 6.46 A certain circuit has input resistance Rin ¼ 20 kO; output resistance Rout ¼ 100 O; and noload voltage gain m ¼ 200. The circuit is driven by a source having output resistance RS ¼ 50 O and available power p ¼ 15 W: The circuit is to drive a load having unspecified resistance RL. Construct a graph of the power gain of the circuit in dB versus load resistance, for 1 O RL 10 kO: Use a logarithmic scale for RL. P 6.47 The voltage gain of a certain circuit is given by
R4
i2
RL m; RL þ Rout
where RS is the output resistance of a source, RL is the resistance of a load, Rin is the input resistance of the circuit, Rout is the output resistance of the circuit, and m is the no-load voltage gain of the circuit. (1) Draw a
+ –
R2 mv1
R3
+ –
RL r i2
+ vL –
circuit diagram for a VCVS two-port model for the circuit. (2) Assuming all other parameters are fixed, specify the values of Rin and Rout that maximize (a) current gain, (b) voltage gain, and (c) power gain. P 6.48 The power gain of a certain circuit is 75 dB. The power delivered to the load is 5 W. What is the power available from the source? P 6.49 The power gain of a certain circuit is 20 dB. The power available from the source is 10 mW. What is the power delivered to the load? P 6.50 The voltage gain of a certain circuit is 55 dB. The voltage available from the source is 5 mV. What is the voltage transferred to the load? P 6.51 The current gain of a certain circuit is 75 dB. The output resistance of the source is RS ¼ 10 kO and the load resistance is RL ¼ 5 kO: (a) What is the voltage gain in dB? (b) If the voltage across the load is 50 V, what is the current available from the source? (c) If the input resistance is 100 kO and the output resistance of the circuit is 100 O, what is the no-load voltage gain of the circuit? P 6.52 For a particular source and load, the voltage gain and power gain of a certain circuit are 120 and 150 dB, respectively. What is the current gain in dB? P 6.53 For a particular source and load, the voltage gain and current gain of a certain circuit are Av ¼ 125 dB and Ai ¼ 30 dB, respectively. What is the power gain in dB? P 6.54 For a particular source and load, the power gain and voltage gain of a certain circuit are Ap dB ¼ 150dB; Av dB ¼ 50 dB: What is the current gain in dB? P 6.55 For a particular source and load, the power gain and current gain of a certain circuit are Ap dB ¼ 150 dB; Av dB ¼ 50 dB: What is the voltage gain in dB?
Section 6.9 is prerequisite for the following problems. P 6.56 Refer to Fig. P 6.27, which is proposed as a temperature-measuring circuit, where V0 ¼ 15 V;
6.10 Problems
195
R + ΔR probe R V0
+ –
+ R R
Fig. P 6.27 See Problem P 6.56
RL ¼ 1 MO; R ¼ 500 kO; and a ¼ 50 Oð CÞ1 : The incremental resistance DR is given by DR ¼ a T; where T C is temperature in C, and the temperature range of interest is 0 C T 100 C: (a) Express the voltage v as a function of vR. Assume that DR R and simplify the expression. Under what condition is the voltage v proportional to the incremental resistance DR (and thus to temperature)? Specify a reasonable value for the amplifier input resistance Ri. (b) Express the voltage vL as a function of temperature (in C). Specify a reasonable value for the amplifier output resistance Ro. (c) The voltage vL must change by 100 mV for each 1 C change in temperature T. Specify the amplifier no-load voltage gain m. (d) If the amplifier no-load voltage gain is 100 and cannot be changed, what other parameter would you adjust to achieve the specified 100 mV C–1, and what value would you specify for that parameter? P 6.57 Refer to Fig. P 6.28. It is required that v1 ¼ v0/2, and the power drawn from the source must be as small as possible. (a) It is known that Ri 5 MO: What values would you choose for R1, R2, and why? (b) It is known that RL ¼ 5 kO and Ro < 10 O: It is required that vL ¼ 25v0 : What value would you specify for m? P 6.58 You are asked to design a circuit that will accept as input a voltage from a photocell and produce as output a voltage related in some known way to the intensity of light incident on the photocell. Based upon your current knowledge, write down each
Ri
+ – mv
v –
+
Ro
RL
vL –
amplifier
R1 + + v – 0
R2
Ri
v1 –
+ – mv 1
Ro
+ RL
vL –
Fig. P 6.28 See Problem P 6.57
substrate
resistive foil
contacts
Fig. P 6.29 See Problem P 6.59
question you must address before you begin designing the circuit. P 6.59 Strain is elongation of a body per unit length, denoted by DL=L; which results from application of force to the body. For example, when a beam is subjected to a downward load in the center, the top of the beam is compressed ðDL < 0Þ and the bottom of the beam is stretched ðDL > 0Þ: For most structural materials, strain (below the fracture point) is on the order of 1 mm/m. Strain is measured using devices called strain gages. The simplest and most commonly used strain gage consists of a foil resistor attached to a flexible substrate, as illustrated by Fig. P 6.29. When the strain gage is stretched or compressed, the resistance of the foil changes in approximate proportion to strain. The relation is
196
6 Dependent Sources and Unilateral Two-Port Circuits
R
R + V 0 –
+ vout – R + ΔR
R
Fig. P 6.30 See Problem P 6.59, 60
Fig. P 6.31 See Problem P 6.60
DL DR ¼ ; L RF where L and R are the nominal length and resistance, respectively, of the gage, DL and DR are the changes in length and resistance, respectively, and F is a constant called the gage factor. The nominal resistance of resistive strain gages is typically about 100 O to 1 kO and the gage factor is typically on the order of 1. Strain gages are often used in four-arm bridge configurations, as illustrated by Fig. P 6.30, where R denotes a fixed resistor and RþDR denotes a strain gage. Let V0 ¼ 1V. (a) Obtain the The´venin equivalent at the output terminals of the circuit in Fig. P 6.30. (b) Show that for DR R; the open-circuit output is given (approximately) by V0 DR : vout ffi 4 R (c) The gage factor of the strain gage is F ¼ 1.8 and the nominal resistance of the gage is R ¼ 350 O. The voltage vout is to be applied to the input of an amplifier whose output is a voltage proportional to strain; that is, DL ; v¼k L with k ¼ 1 V. The output of the amplifier is to be sensed by a voltmeter having input resistance
audio source
amplifier
loudspeaker
Fig. P 6.32 See Problem P 6.61
RVM ¼ 10 MO: Specify the parameters of a unilateral two-port model for the amplifier. Which of the three parameters has the greatest effect on the overall accuracy of a strain measurement? Obtain an expression for the amplifier output voltage without making any approximations. Construct a plot of the percent error in the approximate relation for 106 DL=L 103 : Explore effects of varying the amplifier input and output resistances. (d) Why might one expect the gage factor F for a resistive strain gage to be on the order of 1? P 6.60 Strain gages (see Problem P 6.59) are used in devices called load cells that are used to measure weight (or force). There are various kinds of load cells having different configurations and purposes. Figure P 6.31 shows a sketch of a button load cell. The four wires connect internally to a bridge circuit, such as the one shown in Fig. P 6.30 – two for the power supply and two for the output. When the button is depressed by a force, one or more strain gages inside the device are deformed, and an output voltage proportional to the force is produced. Small button gages are used in small scales (such as postal scales), and can sense weights ranging from zero to a few hundred pounds with accuracies of about 1%. Much larger load cells are used in the scales at truck weigh stations along the interstates. Do a little research on the web and write a one-page paper (not counting figures) on the structure and operation (circuit model) for any particular kind of load cell. Include a web-address list of your sources. P 6.61 Refer to Fig. P 6.32. The audio source has output resistance RS ¼ 250 O and open-circuit voltage VS rms ¼ 25 mV: The loudspeaker has input resistance RL ¼ 8 O: Specify the parameters of a unilateral VCVS two-port model for the amplifier, such that the power delivered to the loudspeaker is 100 W. You are free to make each parameter as large or small as you wish, but justify each specification.
Chapter 7
Operational Amplifiers I
Essentially, an amplifier is a circuit that for some inputs delivers more power to a load than is received from an input. Amplification is achieved by using a small current or voltage (an input) to control a larger current or voltage provided by a power supply and delivered to a load, as illustrated by Fig. 7.1. For example, in a home audio amplifier, the voltage from a CD player (the source) controls the power delivered to the loudspeaker (the load). Nearly all of the power delivered to the speaker terminals is provided by the amplifier’s power supply, which draws its power from a wall outlet. In almost all applications of amplifiers, the power provided by an input is negligible in comparison to that provided by the power supply. Amplifiers are core components of a great many circuits and systems, such as active filters, oscillators, radio transmitters, control systems, and laboratory instruments. Amplifiers can be constructed using discrete components (transistors), or can be purchased (as integrated or modular circuits). It is not a stretch to claim that amplifiers are the most important linear circuits in existence, largely because of what can be achieved using amplifiers in conjunction with feedback. An amplifier is a two-port circuit and, as such, can be partly described by one or more of voltage gain, current gain, transconductance, and transresistance. Most amplifiers are designed such that one of the four gains is approximately independent of source and load resistance. The desired independence is achieved in part by specifying the input resistance and output resistance relative to the source resistance and the load resistance, respectively. Amplifiers also are classified according to which of the gains is approximately independent of source and load resistance. For example, an amplifier whose current gain is
approximately independent of source and load resistances is called a current amplifier. Exercise 7.1. In the table below, Ri, Ro are the input resistance and output resistance, respectively, of an amplifier. The amplifier is driven by a source having output resistance RS and drives a load having input resistance RL. Match each amplifier type on the left with one of the constraints on the right. Amplifier type (a) Current amplifier (b) Transresistance amplifier (c) Voltage amplifier (d) Transconductance amplifier
Constraint (i) Ri RS, RO RL (ii) Ri RS, RO RL (iii) Ri RS, RO RL (iv) Ri RS, RO RL
An amplifier can be represented by any of the twoport circuit models presented in Chapter 6. The kind of amplifier being represented often suggests which of the four two-port models is most appropriate. For example, a transconductance amplifier (voltage in, current out) is most naturally represented by a VCCS model. Exercise 7.2. Match each amplifier type on the left with the most natural model on the right. Amplifier type (a) Current amplifier (b) Transresistance amplifier (c) Voltage amplifier (d) Transconductance amplifier
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_7, # Springer ScienceþBusiness Media B.V. 2011
Two-port model (i) VCVS (ii) VCCS (iii) CCCS (iv) CCVS
197
198
7 Operational Amplifiers I iout
iin + vin
source
+ amplifier
–
load
–
power supply
Fig. 7.1 An amplifier driven by a source and driving a load
Amplifiers are used throughout many electronic systems. Amplifiers often appear as the first (input) stage, which receives an input (e.g., a current or voltage from a sensor), as the last (output) stage, which delivers a current or voltage to a load, and as interior circuits, where they help perform a variety of signalprocessing functions. Amplifiers used as the first or last stages can be any one of the four kinds named above, depending upon the nature of the source and load. Amplifiers used as interior stages for filtering and other signal-processing operations are almost invariably voltage amplifiers. This is because a voltage amplifier typically wastes less power internally (in the output resistance) than does a current or transconductance amplifier and demands less power from a source (input or previous stage) than does a current or transresistance amplifier. Consequently, voltage amplifiers generally require less power from a power supply and generate less heat than do other kinds of amplifiers performing basically the same task. An operational amplifier or op amp is essentially a voltage amplifier having a very large intrinsic dc voltage gain. Hundreds of different op amps are available in integrated-circuit (IC) form. Low-power integrated op amps dissipate a half watt or so, are smaller than a dime, and range in cost from less than 50¢ to a few dollars. High-power op amps dissipate from tens of watts up to a few hundred watts and can cost several hundred dollars. Figure 7.2 shows three integrated op amps. The single 741 and the quad 324 can dissipate about 500 mW and deliver up to approximately 25 mA to a load. The PA03# can dissipate 500 W and deliver up to approximately 30 A to a load. Modern op amps have intrinsic dc voltage gains ranging from about 105 to about 107, input resistances ranging from about 1 MO to about 1 TO 1012 O ; output resistances ranging from about 1 O to about
vout
Fig. 7.2 From left to right: A single 741 op amp, a quad 324 op amp (four op amps in one IC package), and a high-power PA03# op amp (Photograph of the PA03# courtesy of Apex Precision Power Division of Cirrus Logic, Inc)
100 O, and power-dissipation ratings from a few milliwatts to a few hundred watts. Most manufacturers’ web sites provide extensive data on their various offerings. Integrated op amps contain 15 or more transistors, about the same number of resistors, and a few diodes.1 Most also contain one (intentional) capacitor, in addition to the junction capacitances inherent in the transistors themselves.2 Op amps are used in countless applications, including amplifiers, active filters, other linear signal-processing circuits (e.g., integrators and differentiators), and in a host of nonlinear applications, such as oscillators and detectors. This chapter describes operational amplifiers and treats selected circuits using operational amplifiers in feedback configurations. We describe op amps primarily in terms of their terminal characteristics. You will learn more about the internal structure and operation of op amps in a subsequent course on electronic devices and circuits.
1
In integrated op amps, transistors with the base connected to the collector often serve as diodes. 2 We treat capacitance in Chapter 8.
7.1 Operational Amplifier Terminals and Voltage Reference V2 +
Fig. 7.3 Circuit-diagram symbol for an operational amplifier
VCC –
+
p
n
199
o VCC
–
n V1 p
–
V2
n
o
+
p
V1
+
VCC (a)
(7.1)
For integrated general-purpose op amps, VB is typically about 2–10 V and VA is typically about 10–50 V. For example, for National Semiconductor’s LF147 op amp, VA ¼ 44 V and VB ¼ 5 V, which means V2 must be at least V1 þ 5 V, but cannot exceed V1 þ 44 V. In linear circuits, op amps are often powered by symmetric bipolar supplies that provide equal-magnitude positive and negative dc voltages, as shown in Fig. 7.4a. Usually, the supply sources are not shown
3
Real op amps have additional terminals whose functions you will learn when you study electronics. 4 Because of the manner in which the internal circuitry is connected to the supplies, the supplies or supply terminals often are called rails.
–
+
Fig. 7.4 Circuit-diagram symbol for an op amp, showing how the external supply is connected. The meaning of the ground symbol is explained below
VCC n
p
– +
RL
o
reference
VCC +
VA V2 V1 VB :
(b)
–
Figure 7.3 shows a circuit-diagram symbol for an op amp. The symbol in Fig. 7.3 has five terminals:3 The positive input terminal or p terminal, the negative input terminal or n terminal, the output terminal or o terminal, and the power supply terminals, labeled V2 and V1.4 There is no common or ground terminal on an op amp. The reference point for terminal voltages is established by the manner in which a power supply and load are connected to an op amp, as explained below. As does any amplifier, an op amp requires an external source of power to achieve amplification. Power is provided to an op amp by dc sources (supply voltages) connected to the terminals labeled V2 and V1 in Fig. 7.3. For proper operation of an op amp, the voltage V2 must exceed the voltage V1 by at least an amount VB, but must not exceed V1 by more than an amount VA, where VA and VB depend upon the internal structure of the op amp and vary from one op amp to another. Formally, the supply voltages must satisfy an inequality of the form
o
−VCC
–
7.1 Operational Amplifier Terminals and Voltage Reference
– +
Fig. 7.5 Establishing the reference for op-amp terminal voltages
explicitly. Rather, the supply voltages are simply written next to the supply terminals, as shown in Fig. 7.4b. Typical values for VCC are on the order of 2–15 V for small, low-power op amps, ranging up to about 200 V for high-power op amps. As noted above, the reference point for the terminal voltages of an op amp is established by the manner in which the supply and the load are connected to the op amp and to each other. Figure 7.5 shows an op amp driving a load RL. In Fig. 7.5, the power supplies are shown explicitly and the load is connected between the op-amp o (signal-output) terminal and the neutral terminal of the supply, which establishes the neutral terminal of the supply as the reference for all op-amp terminal voltages, as indicated by the ground symbol. Thus, vn means the voltage from the n terminal to the reference and vp means the voltage from the p terminal to the reference. Often, the supply voltage sources and the supply terminals themselves are omitted from circuit diagrams. In such cases, it usually is implied that the power supply is bipolar and symmetric and that the load is connected from the op-amp o terminal to the neutral terminal of the supply. The neutral terminal of the supply is then
200
7 Operational Amplifiers I
the reference for all terminal voltages, and is denoted by the ground symbol in a circuit diagram, as in Fig. 7.5. In practice, the labels n, p, and o shown in Fig. 7.5 also are usually omitted in circuit diagrams. It is understood that the terminal labeled “” is the negative input (n) terminal, the terminal labeled “þ” is the positive input (p) terminal, and the unlabeled terminal at the opposite vertex of the triangular symbol is the output (o) terminal. Nonetheless, for sake of clarity, we often include the labels n, p, and o on circuit diagrams. You might find it helpful to do this also, especially when preparing to replace the op-amp symbol by an equivalent circuit, as we do in the next section.
V2 + vpn –
+
vo
–
V1 (a) op amp
vo V2 Vmax Vmin / m 0 vpn
Vmax / m 0 Vmin
V1 (b) dc transfer characteristic
Fig. 7.6 DC transfer characteristic for an op amp (typical)
7.2 DC Circuit Model for an Op Amp In this chapter, we consider the dc behavior of op amps in order to present some basic ideas in an uncluttered setting. The model and analyses presented in this chapter are strictly applicable only for dc or slowly varying excitation. In Chapter 17, we introduce frequency response and other refinements. The no-load dc transfer characteristic for the dc (or low-frequency) model for an op amp has the form 8 > < Vmin ; m0 vpn Vmin ; vo ¼ m0 vpn ; Vmin < m0 vpn < Vmax ; > : Vmax ; m0 vpn Vmax ;
(7.2)
where the parameter m0 is the intrinsic dc voltage gain. The minimum and maximum output voltages Vmin, Vmax are determined by the internal structure of the op amp and the supply voltages V1, V2. The output vo cannot be less than Vmin and cannot exceed Vmax. Whenever the output of an op amp equals either Vmin or Vmax, i.e., whenever vpn Vmin =m0 or vpn Vmax =m0 ; the op amp is said to be saturated. Figure 7.6 shows a graphical representation of the transfer characteristic (7.2), where V2 > Vmax > Vmin > V1 : The voltage vpn equals zero where the graph crosses the horizontal axis, but the voltage vo at that point is not necessarily zero because the voltages V2 ; Vmax ; Vmin ; V1 might all have the same sign.5
5
Also, a small dc offset voltage afflicts virtually all op amps, as described in Section 7.8.
With reference to Fig. 7.6, it is necessary that V2 > V1 ; but it is not necessary that the supply voltages have opposite signs. This fact is sometimes useful; e.g., we might wish to amplify an input voltage that has a dc offset (a non-zero average value), such that the input is always positive. But in many linear applications, signal voltages have no dc components and op amps are powered by symmetric bipolar supplies, meaning that V1 ¼ VCC ; V2 ¼ VCC : For some op amps, Vmin is about 1 V larger than V1 and Vmax is about 1 V smaller than V2. The output of such an op amp powered by a symmetric bipolar supply V1 ¼ V2 ¼ 15 V ðor VCC ¼ 15 VÞ is confined (approximately) to the range 14V: However, there are so-called rail-to-rail op amps for which Vmin ¼ V1 and Vmax ¼ V2 : To avoid cluttering our treatment with too many details, we assume rail-to-rail operation and a symmetric bipolar supply, which means that the no-load dc transfer characteristic is of the form 8 < VCC ; vo ¼ m0 vpn ; : VCC ;
m0 vpn VCC ; VCC < m0 vpn < VCC ; m0 vpn VCC ;
(7.3)
as shown in Fig. 7.7. The range of values VCC < m0 vpn < VCC is called the range of linear operation, whether one is referring to the input or output; that is, the range of linear operation can mean either the
7.2 DC Circuit Model for an Op Amp
201
vo
Ro
p
VCC
+ –
Ri n
−VCC // m0
VCC // m0
vpn
Fig. 7.8 Linear model for an op amp at dc (for f ¼ 0)
R2
Fig. 7.7 Idealized DC Transfer characteristic for a rail-to-rail op amp having a symmetric bipolar supply
R1 + –
• Input resistance Ri: from about 1 MO to more than 1 TO • Output resistance Ro: from about 1 O to about 1 kO, but typically <100 O • Intrinsic dc voltage gain mo: from about 105 to about 107
m0vpn ref
−VCC
values of an input vpn that satisfy VCC =m0 < vpn < VCC =m0 or (equivalently) the values of an output vo that satisfy VCC < vo < VCC : It is questionable whether any real op amp is truly linear over the so-called range of linear operation. In fact, the voltage gain of an op amp is so large that it is difficult to even measure the voltage transfer characteristic. Nonetheless, the transfer characteristic (7.3) is helpful to explaining and understanding op amp behavior and circuit design, so we shall assume it is approximately true. There is no harm in this assumption because, as we show later, it does not matter in most applications whether the transfer characteristic of an op amp is actually linear over the so-called range of linear operation, so long as jvo j is a great deal larger than vpn for all values of vpn in that range. Figure 7.8 shows a linear model for an op amp at dc that is consistent with the linear portion of the no-load dc transfer characteristic (7.3). The parameters Ri, Ro are the input resistance and output resistance, respectively, and the parameter m0 is the intrinsic dc voltage gain. An op amp is approximately unilateral, so the input resistance is independent of a load attached to the output terminals and the output resistance is independent of a source attached to the input terminals. Typical values for these parameters are as follows:
o
vS
n p
VCC –
o
+
+ –VCC
RL
vL –
Fig. 7.9 See Example 7.1
The model in Fig. 7.8 does not include effects such as saturation, limits on output current, and frequency dependence, all of which are important in all applications. In a subsequent chapter, we treat some of these other effects and refine the model in Fig. 7.8 to account for the fact that the intrinsic voltage gain of an op amp decreases as the frequency of an input increases. Relations obtained in this chapter are applicable only for low-frequency inputs. We cannot quantify low-frequency at this point, because its meaning depends upon the structure of a circuit at hand. Example 7.1. In Fig. 7.9, VCC ¼ 10 V; R1 ¼ 10 kO; R2 ¼ 50 kO; RL ¼ 5 kO; and the source voltage vS is independent of time. The model parameters for the op amp (see Fig. 7.8) are Ri ¼ 1 MO; Ro ¼ 50 O; m0 ¼ 106 : Using the linear model in Fig. 7.8 for the op amp, obtain an expression for the voltage transfer characteristic for the circuit. Solution: We replace the op-amp symbol with the linear model shown in Fig. 7.8 to obtain the circuit diagram shown in Fig. 7.10. We have used the fact that vp ¼ 0 and thus m0 vpn ¼ m0 vp vn ¼ m0 vn :
202
7 Operational Amplifiers I R2
vL (V) 10
R1
Ro
n + –
vS
+ + –
Ri
−m0vn
RL
p
vL = vo
2
−2
vS (V)
– −10
Fig. 7.10 See Example 7.1
Fig. 7.11 See Example 7.1
For the circuit in Fig. 7.10, Kirchhoff’s current law gives Node n: G1 ðvn vS Þ þ Gi vn þ G2 ðvn vL Þ ¼ 0; (7.4) Node o: Go ðvL þ m0 vn Þ þ G2 ðvL vn Þ þ GL vL ¼ 0: (7.5) where we use conductances to simplify the notation; e.g., G1 ¼ R1 1 : From (7.4), vL
ðG1 þ Gi þ G2 Þ G1 vS vn ¼ : G2 G2
(7.6)
ðGo þ G2 þ GL Þ vL : ð G 2 G o m0 Þ
(7.7)
From (7.5), vn ¼
Note that for m0 ! 1; (7.7) gives vn ! 0; in which case (7.6) reduces to vL ffi
G1 vS R2 ¼ vS ¼ 5 vS : G2 R1
(7.8)
To obtain an exact solution, we use (7.7) to eliminate vn in (7.6). This gives ðG1 þ Gi þ G2 Þ
ð G o þ G 2 þ GL Þ vL G2 vL ¼ G1 vS ; ð G 2 G o m0 Þ (7.9)
which yields vL G1 ðG2 m0 Go Þ ¼ vs ðG1 þ Gi þ G2 ÞðGo þ G2 þ GL Þ G2 ðG2 m0 Go Þ ffi 4:99997 ¼ Hv : (7.10)
Here again, if we let m0 ! 1; (7.10) reduces to (7.8). The difference (0.0006%) between the exact solution (7.10) and the approximate solution (7.8) is insignificant because the difference is much smaller than typical uncertainties in parameter values; for example, even in the best of circumstances, the resistances R1, R2 would probably be known only to within 0.05%. Uncertainties in values of the op-amp model parameters might be larger, perhaps as large as 20%. The accuracy of the approximation (7.8) is determined primarily by the magnitude of the intrinsic gain m0 and to a lesser degree by the values of the external resistances R1, R2, RL relative to the internal (model) resistances Ri, R0. Equations (7.8) and (7.10) hold for 10 V < vL <10 V or 2 V < vS < 2 V: For inputs outside that range, the op amp is saturated. Thus a more complete statement of the transfer characteristic is 8 < 10 V; vS 2V; vL ffi 5 vS ; 2V < vS < 2V; : 10V; vS > 2V:
(7.11)
Figure 7.11 shows a graph of the transfer characteristic (7.11)
7.3 The Ideal Op Amp and Some Basic Op-Amp Circuits at DC For most op amps and virtually all linear applications, the approximation m0 ! 1 is so good that it is usually incorporated in the op-amp model itself, at least for first-pass design and analysis of linear op-amp circuits. The approximation m0 ! 1 has two important
7.3 The Ideal Op Amp and Some Basic Op-Amp Circuits at DC
consequences: First, because the output vo ¼ m0 vp vn must be finite, the voltage vpn ¼ vp vn must be exceedingly small.6 Second, because the voltage vpn ¼ vp vn is exceedingly small and the op-amp input resistance is large, the current entering either input terminal must also be exceedingly small. Thus the ideal op amp is defined by the following properties: m0 ! 1;
(7.12)
vp vn ! 0 ) vp ffi vn ;
(7.13)
ip ffi 0; in ffi 0:
(7.14)
Equations (7.12), (7.13) and (7.14) are the fundamental relations for preliminary analysis and design of linear op-amp circuits. In a physical circuit, the voltage difference vp – vn and the currents ip ¼ in are not zero, because if either the current ip or the voltage vpn were zero, no power (no energy) would be delivered to the op amp input, and no physical system can respond to an excitation that conveys no energy to the system. But the output voltage vout (limited by the supply) is typically on the order of a few volts and the intrinsic gain m0 is typically on the order of 105–106, so the voltage vpn ¼ vout =m0 is typically on the order of (at most) about 100 mV. Because the voltage vpn is at most about 100 mV and the input resistance Ri is at least about 1 MO and can exceed 1012 O, the currents ip, in are no larger than a few picoamperes ð100 mV= 1 MO ¼ 100 pAÞ and usually are much smaller than that. In linear applications, the voltage vpn and the currents ip, in are so small relative to other voltages and currents in the external circuit that they are practically zero. Thus (7.14) and (7.13) are true for all practical purposes, provided the op amp is not saturated; i.e., provided jvout j
6
Although vpm is small, the individual voltages vp, vn are not necessarily small.
203 p
Fig. 7.12 Circuit-diagram symbol for an ideal op amp. See (7.13) and (7.14)
+
o
–
n
R2
vS
R1
in
n
–
o
p +
+ vL = vo – RL
Fig. 7.13 See Example 7.2
Because the intrinsic dc gain of an ideal op amp is infinite and the input voltage vpn is zero, we cannot construct a dependent-source circuit model for an ideal op amp. The output would be indeterminate, of the form 1 0. An ideal op amp is simply denoted by the symbol shown in Fig. 7.12. The power-supply terminals often are omitted, the implication being that the supply is adequate for the anticipated ranges of input and output amplitudes. Example 7.2. (Compare with Example 7.1.) Obtain an expression for the voltage transfer characteristic for the circuit shown in Fig. 7.13. Assume the op amp is ideal. Solution: Kirchhoff’s current law at node n gives v n vS v n vL þ þ in ¼ 0: R1 R2 The positive input terminal is connected to ground (to the reference node), so vp ¼ 0. From the property (7.13) of an ideal op amp, vn ¼ vp, so vn ¼ 0. Thus the equation above reduces to
vS vL þ in ¼ 0: R1 R2
From (7.14), in ¼ 0. It follows that the transfer characteristic is
204
7 Operational Amplifiers I vS
p R1
in
+
n –
o
+
R4
vL = vo – vS
R2
R3
v1
+
RL
–
–
R1
vL
RL
+
R2
Fig. 7.14 See Example 7.3 Fig. 7.15 See Exercise 7.3
vL ¼
R2 vS R1
and the gain is given by Av dc
VL R2 ¼ ¼ : VS R1
The circuit in Fig. 7.13 is called an inverting amplifier or an inverter because the input vS and the output vL have opposite signs. Note that the voltage gain is independent of the load resistance RL but depends upon the resistance R1. In many applications, the resistance R1 equals the resistance of an external resistor in series with the source resistance. Usually, the resistance of the external resistance R1 is much larger than the source resistance, in which case the voltage gain is essentially independent of both the source resistance and the load resistance. In such cases, the inverting amplifier is a good voltage amplifier.
Example 7.3. Obtain an expression for the voltage transfer characteristic for the circuit shown in Fig. 7.14. The op amp is ideal. Solution: By Kirchhoff’s current law, v n v n vL þ þ in ¼ 0: R1 R2 From (7.13), vn ¼ vp ¼ vS : From (7.14), In ¼ 0. It follows that vS vS vL þ ¼ 0 ) vL ¼ R1 R2
R2 1þ vS : (7.15) R1
The circuit in Fig. 7.14 is called a noninverting amplifier because the input and the output have the same sign (the transfer characteristic is positive). Note that the voltage transfer characteristic is independent of the load resistance RL. No source resistance is shown in the circuit diagram, but including same would not matter, because no current enters the positive terminal of the op amp; i.e., there would be no drop across the source resistance and the relation vp ¼ vS would remain true. Because the voltage transfer characteristic for an inverting or non-inverting amplifier is independent of the load on the amplifier, the overall voltage transfer characteristic of two or more such amplifiers in cascade equals the product of the transfer characteristics of the individual amplifiers. Exercise 7.3. Obtain an expression for the voltage transfer characteristic for the circuit shown in Fig. 7.15.
Example 7.4. Obtain an expression for the voltage transfer characteristic for the circuit shown in Fig. 7.16. The op amp is ideal. Solution: By inspection, vL ¼ vn. From (7.13), vn ¼ vp. Again by inspection, vp ¼ vS. Thus vL ¼ vS :
7.3 The Ideal Op Amp and Some Basic Op-Amp Circuits at DC p
+ vS
n
–
vL
+ –
205 i
RL
o
v1 v2 v3
Fig. 7.16 See Example 7.4
R
in
R
n – p
R
+
o RL
+ vL –
R
Fig. 7.18 See Example 7.5
vS +
–
RS
+ RL
vL
vS
+ –
+ –
RS
+ RL
–
– RL (a) vL = vS RS + RL
2R
R
vL
(b) vL = vS
Fig. 7.17 Using a follower to buffer a load
v1 v2
–
R
+
R
R
+ RL
vL –
Fig. 7.19 See Exercise 7.4
The circuit in Fig. 7.16 is called a voltage follower because the output voltage equals (follows) the input voltage. Here again, the voltage transfer characteristic is independent of the load RL. Would including a source resistance affect the result above? A follower usually is used to provide a large input resistance and a small output resistance. For example, suppose a fixed load is to be driven by a fixed source, as illustrated by Fig. 7.17. If we drive the load directly with the source, as in Fig. 7.17(a), then the load voltage is given by vL ¼
RL vS : RL þ RS
The voltage transferred to the load depends upon the load and is less than that available from the source. The reduction in available voltage can be significant if the source output resistance RS and load input resistance RL are comparable. But if we insert a follower between the source and the load, as in Fig. 7.17(b), the load voltage equals the source (available) voltage. A follower used as described above and illustrated by Fig. 7.17(b) often is called a buffer.
Example 7.5. Refer to Fig. 7.18. Assume the op amp is ideal and express the load voltage vL in terms of the inputs v1, v2, v3 and the resistance R. Solution: Because vn ¼ vp ¼ 0 and in ¼ 0; we have from Kirchhoff’s current law that i¼
v1 v2 v3 þ þ : R R R
It follows that vL ¼ R i ¼ ðv1 þ v2 þ v3 Þ: The circuit is an inverting adder. The output is independent of the load. If the resistance R is much larger than the largest of the source resistance, the output also is independent of the source resistances.
Exercise 7.4. Refer to Fig. 7.19. Express the load voltage vL in terms of the inputs v1, v2 and the resistance R.
206
7 Operational Amplifiers I R
v1
v2
R
vn vp
R
p
+ vin
–
vo
+
n
–
iL
+ –
o
RL in
R R
Fig. 7.20 See Example 7.6 Fig. 7.22 See Example 7.8 iF n
RF
io
–
p +
o
iS
+ RL
vL – iL
and the load current in terms of the source current iS and the resistances RF and RL. Solution: Because the op amp is ideal vn ¼ vp ¼ 0; and the current entering the negative input terminal equals zero. Thus iF ¼ iS and vL ¼ vo ¼ RF iS :
Fig. 7.21 See Example 7.7
Example 7.6. Refer to Fig. 7.20. Assume the op amp is ideal and express the output vo as a function of the inputs v1, v2 and the resistance R. Solution: By Kirchhoff’s current law, vn v 1 v n v o þ ¼ 0 ) vo ¼ 2vn v1 : (7.16) R R
The circuit is a current-to-voltage converter; that is, the output voltage is proportional to the input current. The circuit also could be called a transresistance amplifier, because the transfer characteristic relating output voltage to input current is real and independent of the load resistance (so long as RL > 0). By Ohm’s law,
By voltage division, vp ¼
v2 : 2
The op amp is ideal, so vn ¼ vp and (7.16) gives v o ¼ v2 v 1 : The circuit in Fig. 7.20 is an example of a difference amplifier. The output is independent of the load. If the resistance R is much larger than the largest of the source resistance, the output also is independent of the source resistances.
Example 7.7. Refer to Fig. 7.21. Assume the op amp is ideal. Express the load voltage vL
iL ¼
vL RF ¼ iS : RL RL
The current-to-current transfer characteristic is not independent of the load, so the circuit is not a good current amplifier. Can we obtain expressions for the transconductance and voltage gain of this circuit? Show how or explain why not.
Example 7.8. Refer to Fig. 7.22, where the op amp is ideal. Obtain an expression for the load current iL in terms of the input voltage vin and the circuit parameters. Thus show that the load current is independent of the load resistance RL.
7.4 Feedback and Stability of Op-Amp Circuits
Solution: The op amp is ideal, so vn ¼ vp ¼ vin : It follows that the voltage across the resistance R also equals the input voltage vin. By Kirchhoff’s current law, iL in ¼
vin : R
The op amp is ideal, so in ¼ 0, and iL ¼
vin : R
The load current is independent of the load resistance RL. The circuit is a voltageto-current converter or transconductance amplifier. A disadvantage of this particular circuit is the fact that the load floats; i.e., neither end of the load shares a ground with the input. This can be a fatal disadvantage if the load is another circuit sharing the same power supply. It might not be a problem if the load is a passive terminal load, such as a loudspeaker. The ideal model for an op amp can be used to analyze and design a number of important circuits. Moreover, it is difficult to use other than the ideal model for initial design because more refined models (and the resulting equations) contain many parameters. In most cases, initial (pencil-and paper) design of a linear circuit using op amps essentially requires use of the ideal model. Subsequently, the design can be refined, if necessary, using one of several circuit simulation programs and more complete models.
7.4 Feedback and Stability of Op-Amp Circuits Because the intrinsic dc gain m0 of an op amp is so large, the slightest electrical disturbance at the input terminals is sufficient to drive the output to saturation (to VCC ). Consequently, op amps are almost always used in feedback configurations, where one or more current paths are provided from the output terminal to
207
one or both input terminals. Feedback from the output to the positive ( p) terminal is called positive feedback and feedback from the output to the negative (n) terminal is called negative feedback. Positive feedback drives the input voltage vpn in the same direction as that taken by the output, and can cause the op amp to saturate. Negative feedback drives the input voltage Vpn in the opposite direction of that taken by the output; i.e., if the output increases, Vpn decreases, and vice versa. Negative feedback reduces the gain of an op amp to usable values by continuously forcing the input of the op amp toward zero. The intrinsic dc voltage gain of an op amp also is called the open-loop dc voltage gain because it is the voltage gain of the op amp in the absence of feedback; i.e., in the absence of a closed loop connecting the input to the output. The feedback is negative in all of the examples in Section 7.3, which illustrate three important virtues of feedback: • Within the accuracy of the approximations employed, and as a result of negative feedback, the overall voltage gain is determined by parameters (resistances) external to the op amp. Because the external resistances can be specified precisely, the transfer characteristic of the feedback amplifier can be specified precisely, even if the values of the op amp intrinsic dc gain m0, input resistance Ri, and output resistance Ro are not known precisely, so long as the intrinsic gain m0 is large enough. • The circuit transfer characteristic is linear, even if the op amp itself is nonlinear in the range jvout j
208
7 Operational Amplifiers I
to the microphone is sufficient to initiate the oscillation. The frequency of the oscillation is determined in part by the distance (delay time) between the loudspeaker and microphone. A purely resistive circuit cannot oscillate, so the output of an unstable resistive op-amp circuit will be either þVCC or VCC, depending upon the sign of the voltage Vpn. Below, we give a condition for stable operation of a resistive op amp circuit that incorporates some positive feedback. To prevent saturation, feedback in an op amp circuit must continuously drive the voltage vpn ¼ vp vn toward zero.7 Loosely, this means that the voltage fed back from the output terminal to the negative input terminal must exceed that fed back to the positive input terminal. For linear operation, the net feedback must be negative. Otherwise, the effect of feedback is to drive the voltage vpn away from zero, and the amplifier will simply saturate (or lock up) at one or the other of the supply voltages. Such saturation in an unstable circuit is inevitable, even if no input is applied to the circuit, because of inherent imbalance between the input terminals of an op amp and also because of ever-present electrical noise. In examples in Section 7.3 above, resistive feedback is presented only to the negative input terminal of the op amp, which ensures stable operation. If feedback also is presented to the positive input terminal, we must ensure that the net feedback is negative. If the feedback is negative and the circuit operates linearly, we say the circuit is stable. If the feedback is positive, then the output is not linearly dependent upon the input and the circuit is unstable. To illustrate conditions for stable operation, we consider the circuit shown in Fig. 7.23, which incorporates both negative and positive feedback. The output voltage is given by vout ¼ m0 vp vn ¼ m0 vpn :
(7.17)
R2 R1
R3
vn vp
–
vout
+
R4
Fig. 7.23 Circuit referred to in obtaining the condition for stable operation
albeit small, between a change in the input vpn and the resulting change in the output vout. A more realistic input-output relation is vout ðt þ DtÞ ¼ m0 vpn ðtÞ:
(7.18)
In words, a change in the input vpn at time t produces a change in the output vout at a slightly later time t þ Dt. To examine the stability of the circuit, we imagine that some small disturbance, such as electrical noise, gives rise to a momentary, non-zero value for the input vpn. No current enters the op-amp input terminals, so we may use voltage division to obtain R3 vout ¼ ap vout ; R3 þ R4 R1 vout ¼ an vout ; vn ¼ R1 þ R2
vp ¼
(7.19)
where the definitions of ap, an are evident. Thus vpn ¼ ap an vout and (7.18) becomes vout ðt þ DtÞ ¼ m0 ap an vout ðtÞ:
(7.20)
Retaining only the first two terms of Taylor’s expansion for the left side of (7.20) yields vout þ
dvout Dt ¼ m0 ap an vout ; dt
which simplifies to According to (7.17), the output voltage responds instantly (in zero time) to the change in the voltage vpn. In a physical circuit, there is some time delay Dt,
m0 ap an 1 dvout : ¼ a vout ; a ¼ Dt dt
(7.21)
The solution of the differential equation (7.21) is 7
Again, the gain of an op amp is so large that if the voltage vp vn is greater than m0/VCC, the amplifier will saturate.
vout ¼ C ea t ;
(7.22)
7.4 Feedback and Stability of Op-Amp Circuits
209
as can be verified by substituting the right side of (7.22) for vout in (7.21). The value of the constant C depends upon the initial state of the op amp; i.e., from (7.22), C ¼ vout ð0Þ; which is non-zero if for no other reason than ever-present electrical noise. The actual value of C is irrelevant. It is sufficient to note that if a > 0; the magnitude of the output increases exponentially with time until the output reaches one of the saturation limits Vmax : In other words, the circuit is unstable for a > 0. But if a < 0, the output goes exponentially toward zero, and the circuit is stable. Because m0 and Dt are both positive, the circuit in Fig. 7.23 is stable if m0 a p a n 1 1 < 0 ) ap < an þ : (7.23) a<0 ) Dt m0
R2 vS
R1
p n
o
+ –
+ v L = vo – RL
Fig. 7.24 See Example 7.9 R + vin
R
n in – +
–
R
ip
o R
p RL
It follows from (7.23) and the definitions of ap, an in (7.19) that the requirement for stable operation of the circuit in Fig. 7.23 is R3 R1 1 < þ : R3 þ R4 R1 þ R2 m0
Fig. 7.25 See Example 7.10
(7.24)
The number 1/m0 is in the neighborhood of 105– 10 . As a practical matter, we may say that for stable, linear operation of an op-amp circuit, the voltage fed back to the negative input terminal must exceed the voltage fed back to the positive input terminal. Although demonstrated above for a specific circuit, this condition holds for linear resistive op-amp circuits in general. It might appear that we could have based the development above on (7.17) and avoided using a differential equation to obtain the condition (7.24). Such an argument would be flawed because (7.17) is an instantaneous relation in which vpm and vout have always the same sign (because m0 is positive). 7
Example 7.9. Obtain the voltage transfer characteristic for the circuit shown in Fig. 7.24. The op amp is ideal. Solution: Assuming vp ¼ vn ¼ 0 and proceeding exactly as in Example 7.2, we obtain vS vL vL R2 þ ¼0) ¼ ?? R1 R2 vS R1
iL
However, this result is meaningless (and incorrect) because the net feedback is to the positive input terminal of the op amp and the circuit is unstable. The output would immediately saturate at one or the other of the supply voltages.
Example 7.10. Refer to Fig. 7.25, where the op amp is ideal. (a) Obtain an expression for the load current iL in terms of the input voltage vin and circuit parameters. Thus show that the load current is independent of the load resistance. (b) Show that the circuit is stable. Solution: (a) Because the op amp is ideal, in ¼ ip ¼ 0 and vn ¼ vp : Let vn ¼ vp ¼ v. By Kirchhoff’s current law, v vin v vo þ ¼ 0 ) vo ¼ 2v vin ; R R v v v vo R v: þ ¼ 0 ) vo ¼ 2 þ þ R RL RL R
210
7 Operational Amplifiers I
1 RL a n ¼ ; ap ¼ 2RL þ R 2
Equate the expressions on the right above (eliminate v0) to obtain R RL 2þ v ¼ 2v vin ) v ¼ vin R RL v vin ) iL ¼ ¼ : R RL
and ap an ¼
So the load current is independent of the load resistance. The circuit is a voltageto-current converter or transconductance amplifier. Unlike the circuit in Example 7.8, the load does not float. But the relation iL ¼ vin =R depends upon the four resistors being identical, which can be difficult to achieve in practice. (b) Based on (7.23), we wish to show that ap < an or, equivalently, that ap an < 0. For vin ¼ 0, Kirchhoff’s current law gives
R <0; RL finite; 2ð2RL þ RÞ
and the circuit is stable, provided RL is finite. If RL ! 1 (open circuit), the circuit is unstable because lim ap an ¼ 0: RL !1
7.5 Input Resistance and Output Resistance of Op-Amp Circuits As discussed in Chapter 6, the input resistance and output resistance of a two-port circuit can be determined (mathematically) as shown in Fig. 7.26. Other approaches are possible; for example, we can use current sources instead of voltage sources as the test sources. Also, we can determine the output resistance by finding the The´venin equivalent resistance at the output terminals.
v n v n vo 1 þ ¼ 0 ) v n ¼ vo ; R R 2 vp vp v p vo RL þ þ ¼ 0 ) vp ¼ vo ; R RL R 2RL þ R so
iout
iin two-port circuit
vin +
–
Fig. 7.26 Definitions of input resistance and output resistance of a two-port circuit
(a) Rin =
p + v – in
n
R1
o
+ –
vout RL
RL
vin
(b) Rout =
iin
iin p
Ri
R2 + –
+ v – in
Fig. 7.27 See Example 7.11
(b)
Ro m 0vpn
+ –
vout iout
o
n
R2 (a)
two-port circuit
RS
vout
vout
7.5 Input Resistance and Output Resistance
211
Example 7.11. (a) Obtain an expression for the input resistance of the non-inverting amplifier shown in Fig. 7.27(a). Do not assume the op amp is ideal (use the dc linear model). Show that for m0 R2 =R1 1; the input resistance is given to a good approximation by Rin ffi
m0 Ri ; Av
where Av is the voltage gain of the non-inverting amplifier. (b) For a typical op amp and non-inverting amplifier circuit, m0 1; Ri R1 ; RL Ro ; R1 Ro ; and m0 R1 R2 : Assume these inequalities hold and simplify the expression obtained in part (a). Solution: (a) We replace the op amp with the linear dc model to obtain the circuit diagram shown in Fig. 7.27(b), where Ri, Ro, m0 are the input resistance, output resistance and intrinsic dc gain, respectively, of the op amp. Applying Kirchhoff’s current law to the n and o nodes in Fig. 7.27(b) gives vn vin vn vn vo 1 1 1 1 1 vn vo ¼ vin ; þ þ ¼0) þ þ Ri R1 R2 Ri R1 R2 R2 Ri vo vn vo m0 ðvin vn Þ vo m0 1 1 1 1 m vn þ vo ¼ 0 vin : þ þ ¼0) þ þ R2 RL Ro R2 Ro Ro Ro RL R2 Eliminating vo from these equations yields vn ¼
½RL ðm0 Ri þ Ro Þ þ R2 ðRo þ RL Þ R1 vin : ðm0 þ 1ÞRL Ri R1 þ ðR1 þ Ri Þ½R2 ðRL þ Ro Þ þ Ro RL þ Ri R1 Ro
The input resistance of the non-inverting amplifier is given by Rin ¼
vin vin vin Ri ¼ ¼ ; iin ðvin vn Þ=Ri vin vn
(7.25)
which, using the expression above for vn, becomes Rin ¼
ðm0 þ 1ÞRL Ri R1 þ ðR1 þ Ri Þ½R2 ðRL þ Ro Þ þ Ro RL þ Ri R1 Ro : R2 ðRo þ RL Þ þ RL ðRo þ R1 Þ þ R1 Ro
(b) If m0 1; Ri R1 ; RL Ro ; R1 Ro and m0 R1 R2 ; then the expression above for Rin reduces to Rin ffi
m0 RL R1 þ R2 RL þ Ro RL þ R1 Ro m R1 þ R2 m R1 m Ri ffi 0 Ri ffi 0 Ri ¼ 0 Ri ; R2 RL þ RL R1 þ R1 Ro R 2 þ R1 R2 þ R1 Av
(7.26)
where Av ¼ 1 þ R2 =R1 is the voltage gain of the non-inverting amplifier. Note that under the conditions imposed in this example, the input resistance of the amplifier is independent of the load resistance.
212
7 Operational Amplifiers I
Exercise 7.5. Repeat Example 7.11, but using a current source as the test input.
Example 7.12. Obtain an expression for the output resistance of the non-inverting amplifier considered in Example 7.11. Do not assume the op amp is ideal (use the dc linear model). Show that under reasonable assumptions (see Example 7.11) the output resistance of the non-inverting amplifier is given to a good approximation by Rout ¼
Av Ro ; m0 þ A v
where Av ¼ 1 þ R2 =R1 is the voltage gain of the non-inverting amplifier. Solution: We attach a source resistance RS to the input and attach a voltage source to the output, as shown in Fig. 7.28. We seek an expression for Rout ¼ vout =iout : Applying Kirchhoff’s current law and vpn ¼ vp vn gives vout m0 vp vn vout vn iout þ ¼ 0; R2 Ro vn vn vn vout þ þ ¼ 0; Ri0 R1 R2 where Ri 0 ¼ Ri þ RS : By voltage division, vp ¼
RS vn : Ri0
Using the latter two equations to eliminate vn and vp from the first equation yields Rout ¼
vout R2 Ro R2a ; ¼ iout ðR2 þ Ro ÞR2a m0 R1 R2 RS þ R1 R0 i ðm0 R2 Ro Þ
where R2a ¼ R1 R2 þ R1 Ri 0 þ R2 Ri 0 : For a typical op amp and non-inverting amplifier circuit, Ri RS ) Ri 0 ffi Ri ; Ri R1 ; Ri R2 ; and R2 Ro . If these inequalities hold, then R2a ffi Ri ðR1 þ R2 Þ and the expression above for Rout reduces to Rout ffi
R2 Ro Ri ðR1 þ R2 Þ Ro ðR1 þ R2 Þ Av ffi ¼ Ro : R2 Ri ðR1 þ R2 Þ þ m0 R1 R2 ðRi RS Þ R1 þ R2 þ m0 R1 m0 þ Av R2
Ri
p RS
n R1
iout
Ro + –
Fig. 7.28 See Example 7.12
o m 0vpn
+ v – out
Exercise 7.6. Repeat Example 7.12, but find the output resistance by finding the The´venin equivalent at the output terminals (load removed) with an ideal independent voltage source attached to the input. You may assume the approximations used in Example 7.12 are valid.
7.6 Properties of Common Op-Amp Circuits
213
Exercise 7.7. Refer to Fig. 7.27. The parameters of a certain non-inverting amplifier are R1 ¼ 1 kO; R2 ¼ 100 kO; RL ¼ 5 kO; RS ¼ 100 O: The op amp has input resistance Ri ¼ 10 MO; output resistance Ro ¼ 80 O; and intrinsic dc voltage gain m0 ¼ 107 : Compute the output resistance and input resistance of the amplifier using both the exact and approximate expressions obtained in Example 7.11 and Example 7.12 above.
Exercise 7.8. Show that the input resistance of the current-to-voltage converter treated in Example 7.7 is given (approximately) by Rin ffi RF =m0 :
7.6.1 Inverting Amplifier See Fig. 7.29.
7.6.1.1 Voltage Transfer Characteristic
vout ¼
ðRo m0 R2 ÞRi RL vin R2 ! vin : ðm0 þ 1ÞR1S Ri RL þ ðRo RL þ Ro R2 þ RL R2 ÞðRi þ R1S Þ þ Ro R1S Ri m0 !1 R1S
(7.28)
7.6.1.2 Input Resistance
Rin ¼
ðm0 þ 1ÞRL Ri R1 þ ðR1 þ Ri ÞðRL þ Ro ÞR2 þ ½ðR1 þ Ri ÞRL þ Ri R1 Ro ! R1 : m0 !1 ðm0 þ 1ÞRL Ri þ ðRL þ Ro ÞR2 þ ðRL þ Ri ÞRo
ð7:29Þ
7.6.1.3 Output Resistance
7.6 Properties of Common Op-Amp Circuits
ðRi R2 þ R1S R2 þ R1S Ri ÞRo ðRo þ R2 ÞðRi þ R1S Þ þ ðm0 þ 1ÞR1S Ri : ðR2 þ R1S ÞRo 1 þ Av ffi ¼ Ro R2 þ R1S þ m0 R1S 1 þ Av þ m0 (7.30)
Rout ¼ Voltage amplification and buffering are common needs, so it is useful to tabulate and compare the essential properties of inverting amplifiers, non-inverting amplifiers, and voltage followers. Equations (7.28–7.36) below give exact (dc), approximate, and limiting (m0 ! 1) expressions for the transfer characteristic, input resistance, and output resistance for each circuit. We omit the derivations, which are straightforward but tedious. In the expressions that follow, R1S ¼ R1 þ RS ; RiS ¼ Ri þ RS :
(7.27)
If m0 ! 1, then Rout ! 0:
(7.31)
If m0 Av 1; then Rout ffi
Av Ro : m0
(7.32)
214
7 Operational Amplifiers I
7.6.2 Non-inverting Amplifier See Fig. 7.30. 7.6.2.1 Voltage Transfer Characteristic
vout ¼
½m0 RiS ðR1 þ R2 Þ þ Ro R1 RL vin R2 ! 1þ vin : ðm0 þ 1ÞR1 RiS RL þ ðRo RL þ Ro R2 þ RL R2 ÞðRiS þ R1 Þ þ Ro R1 RiS m0 !1 R1
(7.33)
7.6.2.2 Input Resistance
Rin ¼
ðm0 þ 1ÞRL Ri R1 þ ðR1 þ Ri Þ½R2 ðRL þ Ro Þ þ Ro RL þ Ri R1 Ro m0 R2 ffi Ri ! 1; Av ¼ 1 þ : m !1 R2 ðRo þ RL Þ þ RL ðRo þ R1 Þ þ R1 Ro Av R1 0
7.6.2.3 Output Resistance
(7.34)
7.6.3.2 Input Resistance
ðR1 R2 þ R2 RiS þ R1 RiS ÞRo ðRo þ R2 ÞðRiS þ R1 Þ þ ðm0 þ 1ÞR1 RiS Av Av R2 ffi Ro ffi Ro ! 0; m0 Av ¼ 1 þ 1: m0 þ A v m0 m0 !1 R1 (7.35)
Rout ¼
Rin ¼
ðm0 þ 1ÞRL Ri þ Ri Ro þ Ro RL R L þ Ro
ffi m0 Ri ! 1:
(7.37)
m0 !1
7.6.3.3 Output Resistance
Rout ¼
7.6.3 Voltage Follower
7.6.3.1 Voltage Transfer Characteristic ðRo þ m0 RiS ÞRL vin ðm0 þ 1ÞRiS RL þ RiS Ro þ RL Ro ! vin :
m0 !1
(7.38)
Table 7.1 summarizes properties given above for circuits in which the op amp is assumed to be ideal.
See Fig. 7.31.
vout ¼
RiS Ro Ro ffi ! 0: ðm0 þ 1ÞRiS þ Ro m0 m0 !1
(7.36)
Exercise 7.9. In Figs. 7.29 and 7.30, let RS ¼ 100O, R1 ¼ 10kO, R2 ¼ 1MO, RL ¼ 5kO, Ri ¼ 10MO, Ro ¼ 100O, and m0 ¼ 106 and calculate the voltage gain, input resistance, and output resistance of each circuit using (a) the exact expressions and (b) the approximate expressions given in Table 7.1.
Table 7.1 Properties of common op-amp circuits for m0 ! 1: See (7.28–7.38) Circuit Voltage Transfer Ratio Hv Input Resistance Inverting amplifier R2 =R1S R1 Ri m0 =Av ! 1 Non-inverting amplifier 1 þ R2 =R1 Follower 1 m0 Ri ! 1
Output Resistance Av Ro =m0 ! 0 Av Ro =m0 ! 0 Ro =m0 ! 0
7.6 Properties of Common Op-Amp Circuits
215 R1 R2
vin
R1
R2
n
vin
Ro RL
– +
Ri
vout
m 0vpn
p
Fig. 7.29 Inverting amplifier (a) and dc model (b)
(a)
vin
vout
vin
RL
Ri
R2
n
vout
p Ro
– R1 R1
m 0vpn
R2
Fig. 7.30 Non-inverting amplifier (a) and dc model (b)
(a)
vin
+ –
vout
RL
Ri
n
A few of the differences between inverting and non-inverting amplifiers are: • An inverting amplifier introduces a sign inversion. A non-inverting amplifier does not. This difference is seldom important. • The input resistance of an inverting amplifier is approximately the resistance R1, which is typically on the order of 10 kO or larger, depending upon the op amp in use. The input resistance of a non-inverting amplifier is larger than that of the op amp, which typically exceeds 1 MO and can be as large as 1 TO. However, in some applications, as discussed in Chapter 17, it is necessary to add a resistance RX from the p input terminal to ground, in which case the input resistance is no larger than RX. • An inverting amplifier can provide a fractional gain (attenuation), whereas the gain of a non-inverting amplifier must exceed unity.8
Achieving gains less than 10 with an inverting amplifier is attended by several problems, as discussed in Chapter 17.
RL
(a)
vout
p Ro
m 0vpn
Fig. 7.31 Follower (a) and dc model (b)
+ –
(b)
vin
8
RL
(b)
vout
+
+ –
+ –
RL
(b)
Of these three differences, the difference in input resistance is most significant. However, even this advantage of a non-inverting amplifier disappears in many applications, as we show in a subsequent chapter. For various reasons, some of which we treat in subsequent chapters, inverting amplifiers are used more often than non-inverting amplifiers. If the relatively low input resistance of an inverting amplifier is a problem, the amplifier can be preceded by a voltage follower, which provides a very high input resistance. For the same voltage gains (magnitudes), the inverting and non-inverting amplifiers have approximately the same output resistance. In a typical application, the voltage gain is on the order of 100. For a typical op amp, m0 ffi 106 and Ro ffi 100, so the output resistances of typical inverting and non-inverting amplifiers are on the order of 10 mO. The output resistance of a voltage follower is on the order of 100 mO. In most applications, the output resistances of inverting and non-inverting amplifiers are negligible compared to the load resistance.
216
The remarks above pertain only to the dc models. We treat ac models for op amps in Chapter 17, where we show that voltage gain, input resistance, and output resistance can all be strong functions of the frequency of a sinusoidal input. We also show how certain additional components required in practical op-amp circuits can alter the conclusions reached above.
7.7 Op Amp Structure and Properties Op amps can be built using various kinds of transistors, such as bipolar junction transistors (BJT’s), junction field-effect transistors (JFET’s), and metal-oxide field-effect transistors (MOSFET’s). The input resistances of op amps range from about 1 MO for BJTbased op amps to more than 1 TO for MOSFET-based op amps. Intrinsic gains range from about 105 to 106 for BJT-based op amps and from about 104 to 105 for MOSFET-based op amps.9 Op amps using JFET’s in the input stage have input resistances and intrinsic gains intermediate to those for BJT-based and MOSFETbased op amps. As we show in Chapter 17, the input resistance of an op amp influences the choice of resistors external to an op amp in inverting or non-inverting configurations. With reference to Figs. 7.29 and 7.30, a good rule of thumb is to make R1 as large as possible but no more than than 1% of the op-amp input resistance.
7.8 Output Current Limit Almost all op amps incorporate internal circuitry that limits the output current to protect internal devices from damage in case the output terminals are shorted (or the op amp is overloaded). Typical limits range from about 1 mA to about 100 mA for small integrated general purpose op amps to more than 25 A for high-power op amps. Because output current is limited, the voltage an op amp can impress on a load also is limited; e.g., any
7 Operational Amplifiers I
particular rail-to-rail op amp can provide the full supply voltage to a load only if the resulting load current does not exceed the limit imposed by the op amp. For example, National Semiconductor’s LM8272 rail-to-rail op amp allows a maximum supply voltage of VCC max ¼ 12 V and a maximum output current of Iout max ¼ 100 mA. Consequently, the op amp cannot drive a resistive load having resistance less than RL min ¼ VCC max =Iout max ¼ 12=0:1 ¼ 120 O and maintain full ð12VÞ output swing. If it is necessary to drive a load having resistance less than 120 O at full swing ( 12 V), we must use a different op amp. The voltage transfer characteristic shown in Fig. 7.7 assumes that the output current limit is not exceeded. Example 7.13. Refer to Example 7.1. (a) What is the minimum acceptable output current limit for the op amp? (b) What is the minimum acceptable load resistance if the opamp output current limit is 10 mA? Solution: (a) Assume full-scale output ( 10 V) is possible. The maximum load current is approximately iL ¼
10 V ¼ 2 mA; 5 kO
so the op amp need supply no more than 2 mA. Almost any op amp can satisfy this requirement. (b) If the op amp can provide 10 mA and if the supply voltage is 10 V, then (assuming rail-to-rail operation) the minimum load resistance is 10 V ¼ 1 kO: 10 mA The solutions above ignore the op amp output resistance, which is a negligible fraction of the load resistances considered.
7.9 Input Offset Voltage 9
This parameter is not specified on manufacturers’ data sheets and is difficult to measure. The values given here are deduced from other performance data. Related topics are discussed in more detail in Chapter 17.
Because of their internal structures, all op amps exhibit a slight imbalance such that an input must be
7.10 Input Bias Currents
217
slightly different from zero to produce an output equal to zero. Thus the output of an op amp is given by
R2
vin
where the (small) voltage vpn0 is called the input offset voltage. Input offset voltages range from about 100 mV to about 10 mV for general-purpose op amps. The input offset voltage and the high dc gain of an op amp will cause a powered, open-loop op amp to saturate even if the input terminals are shorted (even if vpn ¼ 0). Most op amps provide terminals for nulling the input offset voltage; e.g., by connecting a variable resistor to the terminals with the wiper connected to one or the other of the supply voltages, as illustrated by Fig. 7.32. The terminals and recommended nulling circuitry vary from one op amp to another, and are given in manufacturers’ data sheets. High-precision applications may warrant the use of so-called precision op amps that have small offsets and low drift and provide for external nulling circuitry. Unfortunately, the input offset voltage varies with temperature and also tends to drift with time, even if the temperature is constant. Consequently, it is difficult to maintain a perfect null and we must rely on feedback to keep the offset from driving the output to saturation, which means that any practical linear op-amp circuit must provide negative feedback at dc. For present purposes, this means that there must be a resistive path from the output (o) terminal to the negative (n) input terminal. The resistance can be zero, as in a follower. Even if the input offset voltage does not cause the output to saturate, it still causes a corresponding offset in the output voltage. For example, Fig. 7.33 shows a circuit model for the effect of the dc offset voltage in VCC
–
+
−VCC
Fig. 7.32 Circuit for nulling the dc offset voltage (typical)
R1
n′ p′
n + –
vo ¼ m0 vpn vpn0 ;
vpn0
p
– +
vout
ideal op-amp
op-amp with voltage offset Fig. 7.33 Circuit model for input dc offset in an op amp, connected in an inverting configuration
an inverting amplifier. Straightforward application of Kirchhoff’s current law shows that the output voltage is given by R2 R2 vpn0 ; vout ¼ vin 1 þ R1 R1 where the second term on the right is the output offset. Whether the output offset is troublesome depends upon the magnitude of the offset relative to that of the desired output and upon the precision demanded in an application at hand.
7.10 Input Bias Currents Input bias currents are small direct (constant) currents that enter (or exit) the input (p and n) terminals of a powered op amp. Any circuit in which an op amp is imbedded must provide dc paths to ground from both the n and p input terminals. Otherwise, one or both of the bias currents will be blocked, and the resulting input voltage will drive the op amp to saturation. Both input bias currents are the same direction and have approximately the same magnitude, which ranges from less than 1 nA to a few micro amperes. The direction and magnitude of the input bias currents depend upon the internal structure of the op amp. Even if there is a dc path to ground from each input of an op-amp, the input bias currents will cause the voltage vpn (and thus the output) to assume some nonzero value (offset) that is difficult to predict (because of the complexity of the input circuitry in a typical op amp), but which can be large enough to be troublesome, especially in high-precision applications. Below,
218
7 Operational Amplifiers I
we show how the offset can be reduced by a compensating resistor connected to one of the op-amp input terminals. We first consider an inverting amplifier. Figure 7.34 shows an inverting amplifier, where the dc input bias currents are represented by currents In ; Ip . We seek the output vo due to the bias currents alone, so we set the dc offset voltage and the input vS to zero (superposition). The purpose of the resistor RX is to make vp ¼ vn , such that the voltage vo due to the bias currents equals zero. Applying Kirchhoff’s current law to the model shown in Fig. 7.34 gives
Moreover, the dc gain is usually greater than ten, in which case
vn vn v o vp þ In þ ¼ 0; þ Ip ¼ 0 ) vp ¼ Ip RX ; R01 R2 RX (7.39)
In a direct-coupled non-inverting amplifier, the compensating resistor RX is connected to the op-amp p terminal in series with the source, as shown in Fig. 7.36. If the compensating resistor were connected to ground (to the reference node), the compensating resistor would be shunted by the source and rendered ineffective. Here again, we seek an expression for the compensating resistance such that vS ¼ 0 implies vn ¼ vp and vo ¼ 0: From Fig. 7.36 and Kirchhoff’s voltage law, vS ¼ 0 and vo ¼ 0 imply that
where R01 ¼ R1 þ RS :
(7.40)
We assume Ip ¼ In and require vp ¼ vn : This gives Ip RX Ip RX vo þ Ip þ ¼0 R01 R2 RX R2 þ RX R01 R01 R2 ) vo ¼ Ip : R01
RX ffi R1 kR2 ffi R1 ; R2 R1 :
Exercise 7.10. By an analysis like that leading to (7.41), show that the input bias current compensating resistance RX in a current-to-voltage converter shown in Fig. 7.35 is given by (7.42) with R1 ¼ 0 and R2 ¼ RF ; provided RS RF :
vp ¼ Ip ðRS þ RX Þ; vn ¼ In ðR1 kR2 Þ: (7.41) For Ip ¼ In ; it follows that
Requiring vo ¼ 0 yields RX ¼
RS þ RX ¼ R1 kR2 ) RX ¼ ðR1 kR2 Þ RS :
R01 R2 ¼ ðR1 þ RS ÞkR2 R01 þ R2
(7.42)
RX ffi R1 kR2 ; RS ¼ R1 :
n
Ip
p
– +
RL
– + iS
RX
RS
(7.43) Fig. 7.35 See Exercise 7.10
R2 In
(7.45)
RF
Typically, the source resistance RS is much smaller than the resistance R1, in which case R01 ffi R1 and
R1+RS
(7.44)
RS
RX
o
RX
n + –
vS R1
Fig. 7.34 Input dc bias currents in an inverting amplifier
p
Ip In
+
o
RL
–
R2
Fig. 7.36 DC bias compensation for a non-inverting amplifier
7.11 Power Dissipation in Op Amps and Op-Amp Circuits
Simple resistive compensation is not possible if ðR1 kR2 Þ
RX ffi ðR1 kR2 Þ ffi R1 ; R2 R1 RS :
vS +
n
–
RL
o
+ – In
(a) circuit diagram
RS
Ip
In p
o
RL
+ –
m 0 vpn
n Ro
(b) model for analysis
Fig. 7.37 Voltage follower circuit
vn m0 vp vn vn In þ þ ¼ 0: Ro RL (7.48)
To obtain the output voltage vo ¼ vn due to the bias currents alone, we assume Ip ¼ In and eliminate vp from (7.48). We obtain
(7.47)
To obtain (7.42) and (7.45), we assumed that Ip ¼ In : In a real op amp, the bias currents entering the n and p terminals might differ (perhaps by as much as 20%). Also, the relation RX ffi R1 is inexact, so the compensation described above is imperfect. In practice, the compensating resistance often is in part a variable resistor (trimmer) that allows in-situ adjustment. Even then, the dc bias currents can depend strongly on operating temperature, and perfect balance is difficult to achieve and maintain. Nonetheless, an amplifier is more precise with compensation than without, and compensation usually is advisable. We conclude this section by showing that biascurrent compensation is not required for a voltage follower. Figure 7.37 shows the relevant circuit diagram and corresponding model for analysis, where we set the source voltage vS to zero because we are interested in only the output voltage due to the input bias currents. Kirchhoff’s current law gives Ip p
vp þ Ip ¼ 0; RS
(7.46)
Here also, the dc gain usually is large enough that
RS
219
vn ¼ In
ðRo þ m0 RS ÞRL : Ro þ RL þ m0 RL
(7.49)
For m0 ! 1; (7.49) reduces to vn ffi In RS : From (7.48), we have vp ¼ Ip RS ; which also is apparent from the circuit diagram. Because Ip ¼ In ; as assumed above, we have vp ¼ vn ; m0 vp vn ¼ 0: It follows that no compensating resistor is necessary for the voltage follower shown in Fig. 7.37a. Although bias-current compensating resistors usually are included in real circuits, they do not enter into analyses of resistive op-amp amplifiers at dc and alter ac analyses in only a few cases. To avoid distracting clutter, we usually omit showing them in circuit diagrams unless they must be included to obtain a correct analysis.
7.11 Power Dissipation in Op Amps and Op-Amp Circuits Removing heat from a circuit can be expensive, as can providing the wasted power that produces the heat. Circuits that operate hot generally produce more electrical noise than similar circuits that operate at lower temperatures. Also, parameter values change with increasing temperature, and component lifetime generally decreases with increasing operating temperature. For these and other reasons, specifying powerdissipation ratings for circuit components and planning for heat dissipation is an essential part of circuit design. Typical small integrated op amps can dissipate from about 500 mW to a little more than 1 W. Much larger power op amps can dissipate 100 W or more. The power dissipated by an op amp depends upon a number of things, including the supply voltage, the input voltage, the load (output) voltage, the load resistance, and properties of other surrounding circuitry (e.g., the resistors in a feedback network). Thus expressions for power dissipated can be complicated and
220
7 Operational Amplifiers I
difficult to interpret. A circuit designer needs a simple, approximate, and conservative relation that allows initial specification of the power dissipation rating required of an op amp. If necessary, the specification can be refined by subsequent more detailed analysis, by simulation, or by construction and testing. In this section, we derive a few simple relations that are useful in design of linear resistive op-amp circuits. Relations given here are strictly applicable to only op-amp circuits subjected to dc excitation, but can provide useful bounds for a circuit subjected to any excitation. More general relations for circuits subjected to ac excitation are given in Chapter 17. The total power delivered to an op-amp circuit consists of the power PS delivered by the supply and the power Pin delivered to the circuit by an input. The total power dissipated in an op-amp circuit consists of the power PA dissipated in the op amp and the power PR dissipated in the load and other circuit components external to the op amp. Power is conserved, so the power delivered equals the power dissipated; that is, PS þ Pin ¼ PA þ PR :
(7.50)
In virtually all linear applications, the power delivered by an input is negligible (Pin PS ). The power dissipated by an op amp in a linear circuit is given to a good approximation by PA ffi PS PR :
(7.51)
Io > 0
–
+
In what follows, we obtain an expression for the power dissipated by an op amp in a resistive circuit, assuming dc excitation and linear operation. The power dissipated in circuit components external to the op amp is given to a good approximation by
PR ffi
VL 2 ; R0 L
(7.52)
where VL is the load voltage and R0L is the effective load on the op amp, which is the resistance seen by the current exiting the output (o) terminal of the op amp. To minimize waste, we would like most of the power PR to be dissipated in the actual load RL. Figure 7.38 shows how we obtain an expression for the power PS delivered by the supply to an op amp having a dc input. Because of the internal structure of an op amp, positive output current Io passes into the positive supply terminal and out of the op-amp output terminal.10 Negative output current passes into the negative supply terminal and out through the output terminal. In either case, the power delivered by the power supply is given approximately by11 PS ffi VCC jIo j ¼ VCC
jVL j ; R0L
(7.53)
where Io is the current exiting the output (o) terminal of the op amp. The effective load R0L depends upon the actual load on the circuit and (in general) components of the feedback network. For an inverting amplifier and resistive load RL, the effective load is R0L ¼ RL k R2 . For a noninverting amplifier and resistive load RL, the effective load is R0L ¼ RL kðR1 þ R2 Þ. Often, the specified gain is large enough that R2 R1 ; in which case the effective load for a non-inverting amplifier is approximately R0L ¼ RL kR2 . To minimize the load on the op amp (to maximize the effective load resistance), the resistance R2 should be as large as possible, relative to the load RL. The maximum effective load resistance (the minimum load) is the actual load RL. From (7.51), (7.52), and (7.53), the power dissipated by the op amp is given by
VCC p n
+ –
Io
o
RL 10
VCC
Io < 0
+
–
Fig. 7.38 Supply current in a symmetrically powered op amp operating linearly and having a positive output (vo > 0)
The output stage of an op amp is typically a so called push-pull configuration of two transistors, where one transistor amplifies the positive parts of an applied voltage and the other amplifies the negative parts. 11 This is the power delivered by the supply to the output stage. A typical op amp is a three-stage amplifier, and even if no input is applied (even if i0 ¼ 0), some dc power is required to keep the op amp in an active (ready) state.
7.11 Power Dissipation in Op Amps and Op-Amp Circuits
PA ¼ PS PR ¼ VCC ¼
221
jVL j VL 2 0 RL R0L
ðVCC jVL jÞVL : R0L
Example 7.15. (Inverting amplifier) In Fig. 7.40, VCC ¼ 25 V; RL ¼ 100 O; R1 ¼ 10 kO; and R2 ¼ 500 kO: Specify the worstcase power-dissipation rating for the op amp. Solution: Because vn ¼ 0, the effective resistance seen by the current exiting the op amp output terminal (the effective load) is
(7.54)
From (7.54), the power dissipated by the op amp for a dc input is maximum for jVL j ¼ VCC =2 and is given by PA max ¼
VCC 2 : 4 R0 L
(7.55) R0 L ¼ RL k R2 ffi
We show in Chapter 17 that (7.55) gives the worstcase value for the power dissipated by an op amp in a linear resistive circuit. Consequently, (7.55) often is used for initial screening of op amps suitable for a particular application (assuming the supply voltage and the equivalent load resistance are known). Example 7.14. (Follower) In Fig. 7.39, the supply voltage is VCC ¼ 25V and the load resistance is RL ¼ 1 kO: Specify the worstcase power-dissipation rating for the op amp. Solution: The current io equals the load current iL because the current entering the n terminal of the op amp is negligible. Thus the effective load is the actual load on the circuit ðR0 L ¼ RL Þ: The maximum power dissipated by the op amp (the specified power-dissipation rating) for constant (dc) excitation is PA max ¼
VCC 2 ffi 156 mW: 4R0 L
ð500 kOÞð1 kOÞ ¼ 998 O 510 kO
and the maximum power dissipated by the op amp (the specified power-dissipation rating) is VCC 2 ð25 VÞ2 ffi 157 mW ¼ 4R0 L ð4Þð998 OÞ
PA max ¼
Exercise 7.12. (Non-inverting amplifier) In Fig. 7.41, VCC ¼ 25 V; RL ¼ 1 kO; R1 ¼ 10 kO; and R2 ¼ 500 kO: Specify the worstcase power-dissipation rating for the op amp. Equation (7.54) implies that the average power dissipated by an op amp equals zero if the load voltage vL ¼ 0. Actually, an idle op amp draws a dc quiescent current, which usually is given on the manufacturer’s data sheet. For a PA03# high-power op amp, for example, the quiescent supply current for a (75/2) R2
Exercise 7.11. The supply voltage to a follower is 25 V. The circuit is to drive a 2 kO resistive load. Specify the power-dissipation rating for the op amp.
R1
vS
p
p
VCC
+ – −VCC
Fig. 7.39 See Example 7.14
io
iL
i2
io
– o
+
RL
iL +
vL –
Fig. 7.40 See Example 7.15
vS vS
n
n
vL = vS
io
+ o
–
RL
R1 Fig. 7.41 See Exercise 7.12
R2
RL
iL +
vL –
222
¼ 37.5 V supply is about 300 mA, which means that the average power dissipated by an idling PA03# can be as much as (2)(75/2)(0.3) ¼ 22.5 W. In many cases, the idle power is a negligible fraction of the active power, but not always.
7.12 Design Considerations Initial (conceptual) design of linear resistive op amp circuits is based upon the ideal model for an op amp: • The voltage vpn is zero (or the intrinsic dc voltage gain m0 is infinite). • The currents entering the n and p terminals are zero. In addition, three fundamental rules govern design of linear op amp circuits: • The net voltage feedback must be negative, which means that the voltage fed back to the n terminal must exceed that fed back to the p terminal (if any). • There must be negative voltage feedback at dc, which requires a dc path from the o terminal to the n terminal. • There must be a dc path to ground from each of the n and p terminals (for each of the input bias currents). All standard linear op-amp circuits obey these rules. Once a conceptual design is complete, we must select physical components as follows: • The power-dissipation rating of each component must exceed the expected power dissipation. • The precision of each component must be such that any specification on overall precision (e.g., of gain) is met (but see As an aside, below). • The output current required of each op amp must not exceed the maximum current the op amp can supply. • Each op amp must be able to accept power supply voltages that can accommodate the required output swing. • The effective load on each op amp should be minimized, which means the effective load resistance on each should be as large as is practical. This means that the feedback resistor R2 should be as large as possible, which for any particular gain also makes R1 as large as possible and maximizes the input resistance. A rule of thumb for amplifiers using
7 Operational Amplifiers I
general-purpose, integrated BJT-input op amps is that the resistor R1 should be no larger than about 1% of the op amp input resistance.12 Other guidelines based upon frequency response and output slew rate are treated in Chapter 17. As an aside, the precision of component parameters in an integrated circuit is limited; for example, the resistance of a resistor might differ by 10% from the design value. However, such errors are correlated, which means that if a resistor is 10% over- or undervalued, then another resistor in the same area of the circuit will probably be off by about the same amount and in the same direction. Thus, although it might be difficult to achieve a specific resistance with high precision, it is possible to achieve fairly precise resistance ratios, which means, for example, that the gains of integrated inverting and non-inverting amplifiers can be precisely established. For example, if both R1 and R2 in an inverting or non-inverting amplifier differ from their design values by the same fraction a, the voltage gain is nonetheless precise, because ð1 þ aÞR2 R2 ¼ : ð1 þ aÞR1 R1 Thus, in such a case, the main consequence of imprecise resistance values is an imprecise input resistance, which usually is inconsequential. Example 7.16. A certain photodiode produces a current given by iS ¼ ki l;
(7.56)
where l is the intensity of the incident light in watts per square meter and ki ¼ 1 mA W1 m2 : The output resistance of the photodiode is approximately 10 kO. We wish to produce a voltage whose magnitude is given by jvo j ¼ kv l;
(7.57)
where kv ¼ 5 V W1 m2 : The sign of the voltage is immaterial. The maximum intensity
12
We justify this rule in Chapter 17.
7.12 Design Considerations
223 RF
iS
n
–
p
+
vo
o
RS RX
The op amp must be able to accommodate a 17 V output swing. The effective load on the op amp is
RL
R0L ¼ RF kRL ffi RF ;
so the op amp must be able to provide an output current of
Fig. 7.42 See Example 7.16
of the incident light is 3.4 Wm2. The output voltage will be applied to another circuit having input resistance RL ¼ 100 kO: Solution: We would use a current-to-voltage converter (see Example 7.7), as shown in Fig. 7.42, where vo ¼ RF iS ¼ RF ki l:
(7.58)
Equations (7.57) and (7.58) imply RF ¼
kv ¼ 5 kO: ki
(7.59)
Compensating for input bias current completes the conceptual design. From (7.42), we have for an inverting configuration that RX ¼ ðR1 þ RS ÞkR2 : In this example, R1 ¼ 0, RS ¼ 10 kO; and R2 ¼ RF ¼ 5 kO: Thus ð5 kOÞð10 kOÞ RX ¼ ¼ 3:33 kO: 5 kO þ 10 kO The feedback is entirely negative (there is no feedback to the p terminal), the feedback path is resistive, so there is feedback at dc, and there are dc paths from both inputs to ground. From (7.57), jvo jmax ¼ kv lmax ¼ 5 V W1 m2 3:4 Wm2 ¼ 17 V:
(7.61)
jio jmax ¼
jvo jmax 17 V ¼ ¼ 3:4 mA: R0L 5 kO
(7.62)
Virtually any op amp can meet this requirement. Assuming rail-to-rail operation, the required power-supply voltage is VCC ¼ 17 V: From (7.55), the power-dissipation rating for the op amp should be PA ¼
VCC 2 ð17 VÞ2 ¼ 14:5 mW: (7.63) 0 ¼ 4RL ð4Þð5 kOÞ
Virtually any op amp can meet this requirement. The current through the resistor Rx is negligible. From (7.56), the maximum current through the feedback resistor is jiS jmax ¼ ki lmax ¼ 1 mA W1 m2 3:4 Wm2 (7.64) ¼ 3:4 mA; and the required power-dissipation rating for the resistor RF is PF ¼ ð3:4 mAÞ2 ð5 kOÞ ¼ 57:8 mW
(7.65)
so a 1/8 W (125 mW) resistor is more than adequate. The total power requirement for the circuit is the total power dissipated by the circuit (all components). In this circuit, the total power dissipated is approximately that dissipated by the op amp (14.5 mW) plus that dissipated by the feedback resistor (57.8 mW). The powers dissipated by the compensating resistor Rx, the op-amp input resistance, the source resistance, and the load resistance are negligible by comparison. Thus the circuit will demand approximately
(7.60) Ptotal ffi 14:5 mW þ 57:8 mW ¼ 72:3 mW
224
7 Operational Amplifiers I
from the power supply. We might add 10% or 20% (to provide a safety margin) and specify 80 or 90 mW. This figure can be checked in the simulation phase of the design. The overall accuracy of the system is approximately the tolerance of the resistor RF; e.g., for an overall accuracy of 1%, we would specify that tolerance for RF.
7.13 Problems All op amps are ideal unless the problem statement indicates otherwise. In problems calling for simulation, use an op-amp model having the parameters given in Table P 7.1. Section 7.2 is prerequisite for the following problems.
Table P 7.1 Op-amp simulation parameters Parameter Open-loop gain (intrinsic dc voltage gain) Input resistance Output resistance Output swing Input bias current Input offset currenta Input offset voltage Unity-gain bandwidth (gain-bandwidth product)a Slew Ratea Compensation capacitancea a
Value 400 MV V–1 10 GO 5O 25 V 0 0 0 1.5 GHz 500 kVs–1 10 pF
These parameters are treated in Chapter 17
RL
+ –
vS + –
P 7.1 Re-draw the circuits in Fig. P 7.1, replacing the op amp with a linear model. Label the n, p, and o nodes. P 7.2 Refer to Fig. P 7.2. For a certain op amp to operate linearly, the voltage V2 must exceed V1 by at least 5 V, but by no more than 30 V. If a symmetric bipolar supply VCC is to be used, what are the minimum and maximum permissible values of VCC? P 7.3 In Fig. P 7.3, VCC ¼ 15 V; R1 ¼ 10 kO; R2 ¼ 500 kO; RL ¼ 5 kO; RS ¼ 50 O: The op amp has input resistance Ri ¼ 2 MO; output resistance Ro ¼ 30 O; and intrinsic (no-load) dc voltage gain m0 ¼ 105 : (a) Replace the op amp by a linear model and obtain an expression for the voltage transfer characteristic for the circuit. (b) If the op amp is rail-to-rail, for what input amplitudes is the circuit linear? Use a graph of the voltage transfer characteristic to illustrate your answer. (c) Give the voltage gain, current gain, power gain, transresistance, and transconductance of the circuit within the range of linear operation. Express the current, voltage, and power gains in dB. (d) Obtain a simpler expression for the voltage gain by assuming m0 ! 1 in the expression you obtained in part (a). Then repeat part (c). P 7.4 Repeat Problem P 7.3 for the circuit shown in Fig. P 7.4, where RS ¼ 75 O; RL ¼ 1kO;VCC ¼ 12V; Ri ¼ 1MO; Ro ¼ 50 O; m0 ¼ 2 105 : P 7.5 Figure P 7.5 shows (in part) the pin-out diagram for a particular integrated op amp, where V and Vþ are the lower (smaller) and upper supply voltages. Ignore the pins that are not labeled. Re-draw Fig. P 7.3, using the diagram in Fig. P 7.5 for the op amp. Use battery symbols to show how the supply voltages are supplied. Make the diagram as neat and clear as possible, and try to minimize the number of points at which conductors cross but are not connected. P 7.6 Repeat Problem P 7.5 for the circuit in Fig. P 7.4.
R1
RL
+ –
R2
+ v – 2
+ – v1
(a)
(b)
R2
R2 R1 + v – S
Fig. P 7.1 See Problem P 7.1
R1
RL
– +
vS
(c)
+ –
RL
– + R3
R4 (d)
7.13 Problems
225 V2
p
+
n
V1
Fig. P 7.2 See Problem P 7.2
VCC
p
+ –
n
+ v – S
vL
+
o
–
RL
−VCC
R1
R2
Fig. P 7.3 See Problem P 7.3, 5
RS
p
+ v – S
n
VCC
+
o +
– RL
−VCC
vL
–
Fig. P 7.4 See Problem P 7.4, 6 V+ o
Fig. P 7.5 See Problem P 7.5
v1
7
6
5
2
3
4
n
p V −
+
vN
vp
v1
R –
R2
8 1
P 7.7 Refer to Fig. P 7.6. (a) Express the voltage vout in terms of the voltages v1 ; v2 ; ; vN : (b) : Let N ¼ 5, v1 ¼ v2 ¼ ¼ v5 ¼ 1 V; R1 ¼ R2 ¼ ¼ R3 ¼ R ¼ 10 kO; and simulate the circuit. If the simulated result does not agree with the relation obtained in part (a), explain why. P 7.8 Refer to Fig. P 7.7. (a) Express the voltage vout in terms of the voltages v1 and v2. (b) : Let v1 ¼ 1 V; v2 ¼ 2 V; R ¼ 10 kO; and simulate the circuit. If the simulated result does not agree with the relation obtained in part (a), explain why. P 7.9 Refer to Fig. P 7.8. (a) Obtain an expression for the voltage gain. (b) : Let vin ¼ 1 V; R1 ¼ 20 kO; R2 ¼ R4 ¼ 10 kO; R3 ¼ 15 kO; and RL ¼ 5 kO: Simulate the circuit and show that the simulated output agrees with the analysis in part (a). P 7.10 (a) Obtain an expression for the voltage gain Av for each circuit in Fig. P 7.9. (b) : Let R ¼ 10 kO; a ¼ 0.8, vS ¼ 1V, RS ¼ 20 O; RL ¼ 5 kO; and use simulations to check your answers. P 7.11 Obtain an expression for the dc voltage gain of each circuit shown in Fig. P 7.10. P 7.12 Refer to Fig. P 7.11. (a) Obtain an expression for the current iL. What kind of circuit is this?
R R
vout
…
v2
R1
Section 7.3 is prerequisite for the following problems.
o
–
vn
+
vout
–
v2
RN
R
R
Fig. P 7.7 See Problem P 7.8
Fig. P 7.6 See Problem P 7.7
b R4
R2 R3
R1 + vin –
n p
–
o +
+ RL
vout –
Fig. P 7.8 See Problem P 7.9
226
7 Operational Amplifiers I aR
2R
R – +
RS
R
RS
vL
+ R
+ – vS
+ v – S
(a)
R
2R RS
2R +
+
R
+ – vS
RL
(c) RS R3
– +
vS + –
+ vL –
RL
R
+ vS –
10R
+ vL –
10R – +
(a)
R2
+ v – S
10R
RL
(b) bR
R3 R1
+ –
R3
– +
RL
(d)
R2 R1
vL
–
vL
–
+ v – S
Fig. P 7.9 See Problem P 7.10
RL
(b) R
RS
vL
–
RL
aR
2R
R4
– +
vL
R2
RL
R
aR – +
vS +–
vL RL
(c)
(d) R
2R RS
4R
– +
+
2R 3R
vS –+
2R
RL
R
– +
2R + –
+ v – S
vL –
R
– + (e)
2R
+ v – S
Fig. P 7.10 See Problem P 7.11
R
2R
RL
(f ) 2R
RS
vL
– +
i1
2R R
– +
2R R
– +
vL RL
(g)
7.13 Problems
227 R R
ΔR
–
iL
+ v1 +– v2 +–
R
RL R
+ –
Fig. P 7.11 See Problem P 7.12
–
RS
RS
iL
+
RL
vS +–
+ –
a b
R1
+ v – S
R2
Fig. P 7.14 See Problem P 7.15, 16
R
– +
Fig. P 7.12 See Problem P 7.13 R1
R2
–
vS +–
+ R3
R4 RL iL
Fig. P 7.13 See Problem P 7.14
(b) : Let vi ¼ 100 mV; v2 ¼ 200 mV; R ¼ 10 kO; DR ¼ 100 O; RL ¼ 5 kO and simulate the circuit to check your answer. P 7.13 Refer to Fig. P 7.12. (a) Express the load current iL in terms of the source voltage vS. (b) Draw a circuit diagram showing how a power supply would be connected to the op amps consistent with your answer to part (a). P 7.14 Refer to Fig. P 7.13, where R2 =R1 ¼ R4 =R3 : Obtain an expression for the load current iL in terms of the input voltage vS and thus show that the circuit is a voltageto-current converter (a transconductance amplifier). Hint:
Let R2 ¼ aR1 ; R4 ¼ aR3 : (b) It is given that RL ¼ 1 kO; vS ¼ VCC ¼ 20 V and it is required that jIL j ¼ 10 mA: Specify the circuit parameters, making sure that the circuit operates linearly (that the op amp does not saturate). (c) : Simulate the circuit to verify your design. (d) Suppose the resistance ratios are not exactly matched, such that R2 ¼ aR1 ; R4 ¼ ða þ eÞR3 ; where e ¼ a: Under what condition does the circuit remain a good transconductance amplifier? (e) Assume a > 0 and show that the circuit is stable (let vS ¼ 0 and show that vn > vp ). P 7.15 Can you find the The´venin equivalent at the terminals a–b for the circuit shown in Fig. P 7.14, where the op amp is ideal? Do so or explain why not. P 7.16 Can you find the Norton equivalent at the terminals a–b for the circuit shown in Fig. P 7.14, where the op amp is ideal? Do so or explain why not. P 7.17 Refer to Fig. P 7.15(a). What is the voltage vnp? Does this mean that the circuit in Fig. P 7.15(a) is equivalent to the circuit in Fig. P 7.15(b)? Justify your answer.
Section 7.4 is prerequisite for the following problems. P 7.18 : Refer to Fig. P 7.16. (a) Obtain an expression for the transconductance. (b) Show that the circuit is stable. (c) Let vS ¼ 1 V; R ¼ 100 kO; RL ¼ 10 kO and perform a simulation to check the relation obtained in part (a).
228
7 Operational Amplifiers I i
a
n R2
R1
2R
+
p
R2
R1 b
(a)
(b)
R
R3 iL
+ – vS
–
b
Fig. P 7.15 See Problem P 7.17
i
a
RL
R/5
2R
iS
vL
+
– +
RL
R
R1
Fig. P 7.16 See Problem P 7.18
–
R2
Fig. P 7.18 See Problem P 7.20 R1 n iS
p
v1 –
o
+ R2
v2
–
v3
+
vout
v4
iL load
Fig. P 7.19 See Problem P 7.21 100R
100R
Fig. P 7.17 See Problem P 7.19 RS
P 7.19 (a) Obtain an expression for the current transfer ratio Hi of the circuit in Fig. P 7.17. (b) Show that the circuit is stable. (c) Let iS ¼ 1 mA; R1 ¼ 20 kO; and R2 ¼ 2 kO: If the load is resistive, and the supply voltage is 25 V, what is the maximum load resistance for which the circuit is linear? (d) : Use RL ¼ 200 O and the parameters given in part (c) and simulate the circuit to check the relation obtained in part (a). P 7.20 (a) Obtain an expression for the transresistance Hr of the circuit in Fig. P 7.18. (b) Is the circuit stable? (c) : Let iS ¼ 50 mA; R1 ¼ 2kO; R2 ¼ 10kO; R3 ¼ 20kO; RL ¼ 100kO; and simulate the circuit as a check on your answers to parts (a) and (b). P 7.21 Refer to Fig. P 7.19, where all resistors have the same value R. Obtain an expression for the output voltage vout. Is the circuit stable? P 7.22 Refer to Fig. P 7.20, where RS < R and the op amps are rail-to-rail. (a) Obtain an expression for the load current iL. (b) Is the circuit stable? (c) Assume
R
–
vL
iL
+
– v + S
100R
100R
+ –
load
Fig. P 7.20 See Problem P 7.22
a symmetric supply VCC : As the load voltage vL is increased (by increasing the input vS), which op amp saturates first, and why? Obtain an expression for the load voltage corresponding to saturation of the left op amp. (d) Assume the load is resistive and obtain an expression for the maximum allowable load resistance. (e) Assume the load is resistive and obtain an expression for the maximum allowable input vS. P 7.23 Refer to Fig. P 7.21. (a) Obtain an expression for the output vo in terms of the current iS and
7.13 Problems
229 R
R3 n iS
– –
o
p + R1
Rin ⇒
+
RL R
R2
R
Fig. P 7.21 See Problem P 7.23 Fig. P 7.23 See Problem P 7.25, 26 ip
v1
vp
R R
vn
+
vout
–
R vS –
v2
R
R
n
+
p
R
R
–
ΔR
o
a
iL
+ RL R
Fig. P 7.22 See Problem P 7.24
b
+ –
the circuit parameters. (b) Is the circuit stable? (c) If the circuit is stable, obtain an expression for the voltage across the current source. (d) : Let R1 ¼ 20 kO; R2 ¼ 50 kO; RL ¼ 5 kO; iS ¼ 100 mA: Simulate the circuit as a check on the answer you obtained in part (a).
Fig. P 7.24 See Problem P 7.27
100R
iS 100R RS
R
–
Section 7.5 is prerequisite for the following problems.
– +
+ vS 100R
100R
+ –
P 7.24 Refer to Fig. P 7.22. (a) Obtain expressions for the input resistances seen at each input, assuming the other input is connected to an ideal voltage source. (b) : Let R ¼ 22 kO and use a simulation to check your answers. P 7.25 : Refer to Fig. P 7.23. Replace the op amp by a dc model with Ri ¼ 5MO; Ro ¼ 75 O; and m0 ¼ 2 105 ; let R ¼ 1 kO; and obtain an expression for the output resistance. Use a simulation to check your answer. P 7.26 Refer to Fig. P 7.23. (a) Obtain an expression for the input resistance of the circuit. How do you interpret the result? (b) : Let R ¼ 1 kO and simulate the circuit to check your answer. P 7.27 Refer to Fig. P 7.24. Obtain an expression for the input resistance. (b) Obtain an expression for the output resistance. (c) : Let RS ¼ 50O; R ¼ 10kO;
iL
load
Fig. P 7.25 See Problem P 7.28
DR ¼ 100O; RL ¼ 3:4kO; vS ¼ 10mA; and use a simulation to check the expression obtained in part (a). P 7.28 Refer to Fig. P 7.25. Obtain an expression for the input resistance. Hint: Rin ¼ vS =iS Rs : P 7.29 Refer to the current-to-voltage converter circuit in Fig. P 7.26. Assume that the input is an ideal current source, that the input resistance of the op amp is much larger than the feedback resistance Rf, and that the feedback resistance is much larger than the output resistance of the op amp. Show that for m0 ! 1; the output resistance of the circuit approaches Ro =m0 ; where Ro and m0 are the output
230
7 Operational Amplifiers I
RS
Rf iin
RL
+
– +
+ –
vout
vS
– R1
R2
Rout
Fig. P 7.26 See Problem P 7.29
vS + –
RF
RS
+ v1
Rin
–
+ –
mvv1
RL
+ vL –
Fig. P 7.28 See Problem P 7.31
RS
R2
a
+ vS
+ –
R1
v1 –
+ – + mv1
RL
vL –
b Fig. P 7.27 See Problem P 7.30
resistance and intrinsic dc gain, respectively, of the op amp. P 7.30 Refer to Fig. P 7.27. (a) Remove the load and obtain expressions for the voltage v1, the open-circuit voltage, and the shortcircuit current at the terminals a–b. (b) Using the expressions obtained in part (a), obtain expressions for the input resistance, the output resistance, and voltage transfer ratio Hv. (c) Obtain the limits of the expressions obtained in parts (a) and (b) as m0 ! 1: (d) Let RS ¼ 100 O; R1 ¼ 2 MO; RF ¼ 22 kO; R2 ¼ 75 O; and RL ¼ 5 kO: Plot the output resistance and voltage gain (separate plots) versus m0 for 10 m0 106 : Use a logarithmic scale for m0. Section 7.6 is prerequisite for the following problems. P 7.31 Figure P 7.28 shows circuit diagrams for a non-inverting amplifier and a VCVS model for same. The model parameters are the source resistance RS, the amplifier (not op-amp) input resistance Rin, the amplifier output resistance Rout, and a no-load voltage-transfer parameter mv : Note: The parameter mv in Fig. P 7.28
is not the op-amp intrinsic voltage transfer ratio m0. (a) Obtain an expression for the parameter mv in terms of the amplifier model parameters and the voltage transfer ratio Hv for the amplifier. (b) Show that if Rin RS and Rout ¼ RL ; then mv ffi Hv : P 7.32 Figure P 7.29. shows circuit diagrams for an inverting amplifier and a VCVS model for same. The model parameters are the source resistance RS, the amplifier (not op-amp) input resistance Rin, the amplifier output resistance Rout, and a voltage-transfer parameter mv : Note: The parameter mv in Fig. P 7.29 is not the op-amp intrinsic voltage transfer ratio m0. (a) Obtain an expression for the parameter mv in terms of the amplifier model parameters and the voltage transfer ratio Hv for the amplifier. (b) Show that if Ri RS and Ro ¼ RL ; then mv ffi Hv : In solving problems P 7.33 through P 7.38, use the relations given in Section 7.6. P 7.33 The parameters of a certain inverting amplifier and associated op amp are R1 ¼ 10 kO; R2 ¼ 500 kO; RS ¼ 50 O; Ro ¼ 50 O; Ri ¼ 2 MO; RL ¼ 5 kO: Plot the approximate voltage gain R2 =R1 and the actual gain given in Section 7.6 in the text versus the no-load voltage gain m0 ; for 1 m0 105 : Use a logarithmic scale for m0 : P 7.34 Repeat Problem P 7.33 for a non-inverting amplifier. P 7.35 Ignore irrelevant parameter values given in Problem P 7.33 and repeat that problem for a voltage follower. P 7.36 Using the parameter values given in Problem P 7.33, plot the actual and approximate input
7.13 Problems
231
R2
+
RS + –
R1
RL
–
vin
+
vS
–
Rout + v1
RS
vS +–
Rin
–
+ –
mvv1
10R
R
RL
–
20R
–
25R
R
+ 15R
R
– +
vout –
Assume the op amps are rail-to-rail. What is the maximum input voltage for which the output voltage is given by vout ¼ Av vin ? (c) If each op amp has an output current limit imax ¼ 1 A and if jvout j VCC , what is the minimum load resistance for which the output voltage is given by vout ¼ Av vin ?
+
+ vin
–
Fig. P 7.31 See Problem P 7.40
+ vL
Fig. P 7.29 See Problem P 7.32 R
+
–
+
– +
vout –
Fig. P 7.30 See Problem P 7.39
resistances and the actual and approximate output resistances for an inverting amplifier versus m0 ; for 1 m0 105 : Use logarithmic scales for both Rin and m0 : P 7.37 Repeat Problem P 7.36 for a non-inverting amplifier. P 7.38 Repeat Problem P 7.36 for a voltage follower. (Ignore irrelevant parameters.) Section 7.10 is prerequisite for the following problems. P 7.39 Refer to Fig. P 7.30, where each op amp is powered by a symmetric 15 V supply. (a) Obtain an expression for the voltage gain Av : (b) Assume the op amps are rail-to-rail. What is the maximum input voltage for which the output voltage is given by jvout j ¼ Av jvin j? (c) If each op amp has an output current limit imax ¼ 750 mA and if jvout j VCC , what is the minimum load resistance for which the output voltage is given by jvout j ¼ Av jvin j? P 7.40 Refer to Fig. P 7.31, where each op amp is powered by a symmetric 12 V supply. (a) Obtain an expression for the voltage gain Av ¼ vout =vin : (b)
.Note: Most op amps provide a means for nulling the input offset voltage, as described in the text. Manufacturer’s data sheets specify how such nulling is achieved, usually via a variable resistor connected to the power supply and to additional terminals provided for that purpose. However, the simplest op amp models in simulators such as Pspice and Electronic Workbench do not provide special pins for nulling circuitry. The 1 mV offset is troublesome for inputs less than about 100 mV, and in such cases can be cancelled by connecting a dc source in series with an input, as illustrated for an inverting amplifier by Fig. P 7.32. (The 9.8 kO resistor compensates for the input bias currents). As you can see, the output for Vs ¼ 1 mV is approximately ðR2 =R1 ÞVS ¼ 50 mV, as it should be. That would not be the case if the 1 mV offset cancellation (at the p input) were not present. Another way to handle this problem is to modify the virtual op-amp model by reducing the input offset voltage to zero, as suggested by Table P 7.1. Your instructor can specify how you should handle input offset cancellation in simulation problems. Input offset voltage becomes less significant as the amplitude of the input increases (or for ac coupling, as described in Chapter 17). For example, if the input in Fig. P 7.32 were 100 mV instead of 1 mV, the output would be within about 1% of 5 V.
232
7 Operational Amplifiers I
Fig. P 7.32 See note following Problem P 7.40
R2 RS
R1
n1 p1
vS + –
– +
o1
RX
RY
R3
p2 n2
+ –
RX
RL R4
Fig. P 7.33 See Problem P 7.41, 48
RS
o2
RX
+ –
vL
+ –
vS +
RL
–
Fig. P 7.34 See Problem P 7.42, 49
P 7.41 Refer to Fig. P 7.33, where RS ¼ 25 O and RL ¼ 5 kO: The overall voltage gain of the circuit is to be approximately 4000 and the input resistance is to be at least 20 kO. (a) Assume the op amps are ideal and specify reasonable values for all resistors shown. Justify each choice. (b) : Use simulation to verify your design. P 7.42 Refer to Fig. P 7.34, where RS ¼ 100 O and RL ¼ 15 kO: The overall voltage gain of the circuit is
R1
R2
R1
R2
to be approximately 104 and the input resistance is to be at least 10 kO. (a) Assume the op amps are ideal and specify reasonable values for all resistors shown. Justify each choice. (b) : Use simulation to verify your design. P 7.43 Show how to compensate for input bias currents in the circuit in (a) Fig. P 7.6. (b) Fig. P 7.7. (c) Fig. P 7.8. Assume the source resistance(s) are negligible.
7.13 Problems
233
supplies VCC ; and equal resistive loads RL, then (i) both amplifiers draw the same power from their respective power supplies and (ii) the powers dissipated by the op amps in the two amplifiers are equal. 3. Let I denote an inverting amplifier and N denote a non-inverting amplifier. A two-stage amplifier is to be built as one of the cascades II, IN, NI, or NN. The two-stage amplifier is to be powered by a symmetric supply VCC and must drive a resistive load RL. Which of the four two-stage cascades requires the least power from the supply? 4. Let R1 ¼ 10 kO; R2 ¼ 100 kO; RL ¼ 5 kO; VCC ¼ 15 V; and VS ¼ 100 mV: Calculate the total power required by each of the two-stage cascades.
Section 7.11 is prerequisite for the following problems. P 7.44 Re-draw the circuit shown in Fig. P 7.3 to show how the reference point for pin voltages is established by the manner in which the supply and load are connected to the op amp. Use battery symbols to represent the positive and negative supplies. Show the effective load and the paths taken by the current exiting the op-amp output terminal for both positive and negative output voltages. Keep in mind that no (or negligible) current enters the op-amp input terminals. P 7.45 Repeat Problem P 7.44 for the circuit in Fig. P 7.4. P 7.46 Repeat Problem P 7.44 for an inverting amplifier. P 7.47 What is the effective load on the op amp in the circuit of Fig. P 7.8? P 7.48 Refer to the two-stage amplifier shown in Fig. P 7.33. (a) Obtain expressions for the power delivered by the supply to each stage, the power dissipated by the resistive components of each stage, and the power dissipated by each op amp. (b) Let VCC ¼ 15 V; vS ¼ 100 mV; RS ¼ 75 O; R1 ¼ R3 ¼ 10 kO; R2 ¼ R4 ¼ 100 kO; RL ¼ 5 kO and calculate the total power required of the supply. Assume ideal op amps, a symmetric supply, and rail-to-rail operation. P 7.49 Repeat Problem P 7.48 for the circuit in Fig. P 7.34. P 7.50 Refer to Fig. P 7.35, which shows (a) an inverting amplifier and (b) a non-inverting amplifier. The op amps are ideal and the source resistance is negligible.
P 7.51 Obtain an expression for the power required by the circuit in Fig. P 7.6, with N ¼ 3: Assume source resistances are negligible, that the op amps are ideal and rail-to-rail, that the supply is symmetric (denoted by VCC ), and that the load is resistive (denoted by RL). P 7.52 Obtain an expression for the power required by the circuit in Fig. P 7.8. Assume source resistances are negligible, that the op amps are ideal and railto-rail, that the supply is symmetric (denoted by VCC ), and that the load is resistive (denoted by RL). P 7.53 Repeat Problem P 7.51 for the circuit in Fig. P 7.36. P 7.54 Obtain an expression for the power dissipated by the op amp in the circuit in Fig. P 7.7. Assume source resistances are negligible, that the op amps are ideal and rail-to-rail, that the supply is symmetric (denoted by VCC ), and that the load is resistive (denoted by RL). P 7.55 Repeat Problem P 7.54 for the circuit in Fig. P 7.8. P 7.56 Repeat Problem for the circuit in Fig. P 7.36.
1. Show that the amplifiers in Fig. P 7.35 have equal voltage gains. 2. Show that if the inverting and non-inverting amplifiers have equal dc inputs VS, equal symmetric
R2 vS
R1
n
– + p
o
vo
RX
vS
p n
+ –
o
RX R2 − R1
R1
Fig. P 7.35 See Problem P 7.50
(a)
(b)
vo
234
7 Operational Amplifiers I
R
vL
R
v1
RL
v2
Fig. P 7.36 See Problem P 7.53, 56
R
R
R R
vS
R
n
o
ΔR
vS
IL
p RL R
VL
Fig. P 7.37 See Problem P 7.59
P 7.57 The power supply for a circuit must be able to provide the total power dissipated by the circuit. Usually, a power supply will be specified with a margin of 20% or more; for example, if the circuit to be powered dissipates 100 W, the designer might specify a 120 W supply. Use a 25% margin and specify the capacity of a power supply for the circuit in P 7.8, where vin ¼ 700 mV; VCC ¼ 20 V; R1 ¼ 10 kO; R2 ¼ R4 ¼ 50 kO; R3 ¼ 22 kO; and RL ¼ 5 kO:
Section 7.12 is prerequisite for the following problems. Note: Material presented in this chapter permits conceptual design of certain op amp circuits, based upon the ideal dc model for an op amp. Resulting circuits would work as specified if the op amps were ideal and if the currents and voltages involved are constant or slowly varying, but might not work with real op amps or for rapidly varying inputs. More realistic circuits typically require additional components whose roles we are at this point unprepared to discuss. Chapter 17 offers a more complete treatment of op amps and op amp circuits, where design can be
discussed in more depth. The problems that follow are to be interpreted as conceptual design problems, with additional constraints imposed by supply voltage and maximum output current. In all cases, you should verify (and perhaps fine-tune) your design using simulation software. P 7.58 : Design an amplifier whose transresistance equals 1 kO and is independent of the load resistance. The source resistance is 500 kO. If the maximum output current (magnitude) is 35 mA, and the load resistance ranges from 2 to 4 kO, what is the maximum permissible supply voltage? Use a simulation to verify your design. P 7.59 (a) Show that the circuit in Fig. P 7.37 is a transconductance amplifier. (b) If the supply voltage, the load resistance, and DR are fixed, what is the maximum permissible magnitude of the excitation vS (for linear operation)? (c) Design an amplifier whose transconductance equals 2 mS and is independent of the load resistance. (d) : Use a simulation to verify your design.
7.13 Problems
P 7.60 A certain tachometer produces a voltage given by v ¼ kT n; where n is the angular velocity of the rotor in rpm and kT ¼ 100 mVðrpmÞ1 : (a) Design a circuit that will convert the voltage v produced by the tachometer to a current i ¼ kA v that will drive a 50 O load. As the speed of the tachometer ranges from zero to 200 rpm, the magnitude of the current provided to the load must range from zero to 40 mA. (b) Will the circuit operate linearly over the specified range of the tachometer output? (c) : Use a simulation to verify your design. Hint: See Problem P 7.59. P 7.61 A small, low-power portable appliance requires a 9 V battery or supply and draws no more than 20 mA. (a) Design an op amp circuit that efficiently converts the 12 V available from an automobile battery to the 9 V required by the appliance. Show how to power the op amp from the automobile battery, given that the input is positive and that the output is positive and less than 12 V. (b) What dissipation rating is required for the op amp? Why would you use such a circuit instead of a simple resistive voltage divider? (c) How efficient is the circuit? (d) : Use a simulation to verify your design. P 7.62 : The voltage produced by a certain source ranges from zero to 2 V. Design a circuit that effectively converts the voltage to a current that ranges from zero to 20 mA. Use a simulation to verify your design. Hint: See Problem P 7.59. P 7.63 A photodiode produces a current that is approximately proportional to the intensity of incident light. The angular velocity of a small permanent-magnet dc motor is proportional to the voltage impressed on the motor armature. Design a circuit that makes the
235
speed of the motor proportional to the light incident on the photodiode. P 7.64 The resistance of a certain pressure sensor is given by Rð pÞ ¼ R0 þ a ðp p0 Þ; where p is atmospheric pressure, p0 ¼ 101 kPa is a reference pressure (approximately equal to average sea-level atmospheric pressure), a ¼ 1 O kPa1 ; and R0 ¼ 100 O is the resistance for p ¼ p0 : Design a circuit which, when driven by the pressure sensor, produces a voltage given by v ¼ kðp p0 Þ; 0:8 p0 p 1:2 p0 ; where k ¼ 100 mV kPa1 : Use a Norton source model incorporating the pressure sensor, assuming you have available a good current source whose output resistance is much, much larger than R ð pÞ for any pressure of interest. P 7.65 A certain photocell produces a current given by i ¼ k0 l; where l is the intensity of the incident light in Wm2 and k0 ¼ 1 mA W1 m2 : The internal resistance of the photocell exceeds 50 kO. In a certain application, an array of four such photocells is to be used to measure the average intensity of light incident on a surface. Design a circuit whose inputs are the currents from the photocells and whose output is a voltage having magnitude jvL j ¼ kV L; where L is the average of the intensities incident on the four photocells and kV ¼ 10 V W1 m2 : The maximum intensity of the incident light is lmax ¼ 1:7 Wm2 and the load resistance exceeds 10 kO.
.
Chapter 8
Capacitance
An ideal resistor is a purely dissipative element. A resistor does not generate electrical energy, nor does it store electrical energy for release at a later time. The terminal voltage v at any time is given by v ¼ i R, where i is the current at the same time. Consequently, the response of a resistor to current through or voltage across its terminals is instantaneous, depending only on the present value of the voltage or current. Simply put, a resistor has no electrical memory.1 Consequently, a resistive circuit as a whole has no electrical memory. The output voltage or current at any instant depends only upon the input voltage or current at the same instant. Some useful circuits are, for all practical purposes, resistive. But most useful signal-processing operations, such as integration and filtering, require memory and cannot be performed by a purely resistive circuit. At any time t, the output of a circuit or circuit element having memory depends upon values of the input at times earlier than t.2 There are two passive elements that exhibit memory: capacitors and inductors. These elements exhibit memory because they can store energy for later release, which allows the present output of a circuit containing these elements to depend upon previous inputs. In a capacitor, energy is stored in an electric field. In an inductor, energy is stored in a
magnetic field. We treat capacitance in this chapter and inductance in the next.
8.1 Capacitance Figure 8.1 shows two parallel conducting plates separated by an insulator (e.g., air) and connected by wires to a battery. When the battery is first connected to the plates, electrons are drawn away from the upper plate by the positive charge on the positive terminal of the battery and forced through the battery to the lower plate. As electrons migrate away from the positive plate and toward the negative plate3 current exists in the circuit in the direction shown. As the current continues, uncovered positive charges left behind by departing electrons make it increasingly difficult for the battery to pull electrons away from the upper plate. Because charge cannot pass through the insulating medium, the current decreases with time until the voltage across the plates is equal in magnitude and opposite in sign of that across the battery terminals.4 At that point, the battery can no longer draw electrons away from the upper plate and the current goes to zero. The time during which all this happens depends upon the magnitude of the current (the rate at which the charge is transferred), which in turn depends upon
1
Resistors do possess thermal memory because resistance changes with temperature and the temperature of a resistor depends upon past current through the resistor. This particular form of memory has not been found useful in signal-processing circuits. 2 So far as we know, the present output of a circuit (or any other physical system) cannot depend upon future values of an input. If it were otherwise, we could predict the future.
3
Recall that the positive direction for current is opposite to the direction of electron flow. 4 Electrons migrate until the work the battery can do on a charge equals the work necessary to move the charge from the positive (upper) plate through the circuit to the negative (lower) one, or, until Kirchhoff’s voltage law is satisfied, whichever perspective you prefer.
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_8, # Springer ScienceþBusiness Media B.V. 2011
237
238
8 Capacitance I
+ battery
–
I
+
++++++++++++++ T E
V –
t
––––––––––––––
Fig. 8.1 Charged parallel conducting plates separated by an insulating medium
the ability of the battery to supply current, the area and separation of the plates, the resistance of the wires and plates, and the internal resistance of the battery itself. Exercise 8.1. Refer to Fig. 8.1. Draw a qualitative graph of the voltage V versus time, beginning at t ¼ 0 when the battery is first connected to the plates and assuming the voltage equals zero at that time. If the battery is disconnected from the plates, the plates remain charged, because there is no path by which the electrons can return to their original locations.5 If the battery is reconnected, but with polarity reversed, a current will again exist until the plates are fully charged in the opposite manner. This process – disconnecting and then reconnecting the battery with opposite polarity – could be repeated indefinitely, in which case the current might be as shown (qualitatively) in Fig. 8.2. As illustrated by Fig. 8.2, current can exist in the circuit of Fig. 8.1 even though no charges move through the insulator separating the plates. This phenomenon puzzled scientists for years because of their firm (and correct) belief that current is continuous on a closed path. The puzzle was solved by Maxwell,6 who showed that there are two kinds of current: Conduction current, which is motion of charge, and displacement current, which can exist even where no charges are present – even in free space – if time-varying electric
Fig. 8.2 Qualitative graph of current in the circuit of Fig. 8.1 when the polarity of the battery is periodically reversed (at the times 0, T, 2T, . . .)
fields are present. Total current (conduction þ displacement) is continuous. In the circuit of Fig. 8.1, the current in the wires is predominantly conduction current, the current in the insulating medium between the plates is predominantly displacement current, the total current everywhere in the circuit is the same, and the total current is nonzero only while the electric field between the plates is changing. Once the electric field is established and unchanging, the displacement current goes to zero, the space between the plates is an open circuit, and the total current goes to zero as well.7 Example 8.1. A 15-V battery is connected to a pair of plates separated by an insulating medium, as shown in Fig. 8.1. The initial charge on each plate equals zero. The battery is connected to the plates at t ¼ 0, after which time the current through the battery is given by iðtÞ ¼
The charge will gradually leak through the imperfect insulator separating the plates, but for a good insulator, the leakage will occur very slowly. 6 James Clerk Maxwell (1831–1879).
0; I0 et=t ;
t < 0; t 0;
(8.1)
where I0 ¼ 50 mA and t ¼ 20 ps. Find the charge on the positive plate after the battery has been connected for a very long time (for t ! 1).
7
5
2T
0
Further discussion of displacement current is beyond the scope of this book. Conduction current is the dominant current in elements and circuits considered in this book, except in insulating media inside capacitors, where the current is predominantly displacement current. Even in that case, we are concerned only with the conduction current into and out of the terminals of the capacitor.
8.2 Capacitors
239
Solution: Charge is the integral of current. Thus, for t 0, qðtÞ ¼
ðt 1
iðt0 Þ dt0 ¼ h
it
ðt
0
I0 et =t dt0
0
is charged to v (volts), even though charge and voltage are different things. Such language, though imprecise, is commonly used and understood by electrical engineers. The capacitance of a parallel-plate capacitor9 is given approximately by10
¼ I0 t et =t ¼ I0 t 1 et=t : (8.2) 0
C¼
0
For t ! 1, the exponential vanishes and qð! 1Þ ¼ I0 t ¼ 1 pC:
(8.3)
8.2 Capacitors The parallel-plate arrangement in Fig. 8.1 constitutes a capacitor. Capacitors for use in circuits are constructed of parallel conductors, called plates, separated by an insulating medium, such as air, paper, glass, mica, and various ceramics and plastics. The insulating material separating the plates is called the dielectric for the capacitor. Often, the plates are long strips of metal foil or metalized plastic, separated by an insulator and wrapped into a tight cylinder, with a terminal (a wire) connected to each of the foil strips. It is shown in introductory physics textbooks that the charge (magnitude) on either of the parallel plates is given by
e0 er A ; d
(8.5)
where e0 ¼ 8:854 1012 F m1 is the permittivity of a vacuum, er 1 (dimensionless) is the relative permittivity of the dielectric (er ¼ 1 for a vacuum or air), A is the area of one plate, and d is the distance between the plates. The approximation (8.5) is quite good if the separation d is very much smaller than both the width and the length of a plate. Achieving a large capacitance requires a dielectric having large relative permittivity, a large plate area, and a small plate separation. However, the dielectric thickness (plate separation) must be large enough to withstand normal working voltages without breaking down (without allowing an arc between the plates). Example 8.2. The capacitance of a parallelplate capacitor having an air (free-space) dielectric is 1.00 F. The separation of the plates is 100 mm (about the thickness of a sheet of notebook paper). Find the area of either plate. Solution: From (8.5),
q ¼ Cv;
where v is the voltage across the plates (from positive to negative), q is the magnitude of the charge on either plate, and C is a constant called the capacitance of the parallel-plate arrangement. The unit of capacitance is the farad (F),8 where 1 F equals 1 C V1 or, equivalently, 1 A s V1. A two-terminal device so constructed that its dominant electrical property is capacitance is called a capacitor. It is customary to refer to the charge on the positive plate of a capacitor as the charge on the capacitor, even though the net charge on the capacitor as a whole is zero. It also is customary to say the capacitor
8
C d ð1FÞ 100 106 m A¼ ¼ e0 8:85 1012 Fm1 ffi 11:3 106 m2 :
(8.4)
After the English scientist Michael Faraday (1791–1867).
(8.6)
If the plates were square, each would be about 3.4 km (2 miles) on a side. As you can see from Example 8.2, a 1 F capacitor is quite large. Most capacitors used in electronic circuits have capacitances ranging from about 10 nF to about
9
In a parallel-plate capacitor, the plates are of equal area and uniformly separated with their edges aligned. 10 Eq. (8.5) is derived in virtually all university-level introductory physics textbooks.
240
1 mF. Those used in power supplies, often the largest capacitors in an electronic system, have capacitances on the order of 20 – 2000 mF. Some off-the-shelf capacitors, like resistors, are commonly available in only certain sizes, again from E series. Unlike resistors, the E3 and E6 series of values are widely used for some common types of capacitors because of the difficulty of manufacturing those types to higher precision. The E6 and E3 (in bold) series are (10, 15, 22, 33, 47, 68). The corresponding capacitance values are the series numbers multiplied by an integer power of ten; e.g., 4.7 pF, 47 pF, 470 pF, and so on. Higher series values for certain types of capacitors can be obtained at higher cost. But also, improved manufacturing processes and better materials have made it possible to manufacture some kinds of capacitors to almost any value at relatively high precision. It is not difficult to obtain (in bulk) capacitors having capacitances of 1.0, 2.0, 3.0, 4.0, 5.0, . . . pF, although none but the first of these values is from an E series. In addition to capacitance and kind of dielectric, capacitors are characterized by the maximum voltage they can endure without breakdown (conduction through the dielectric). All else equal, a thin dielectric provides greater capacitance than a thicker one but offers less resistance to breakdown. Thus a capacitor might be rated at 120 pF and 50 VDC, meaning that 50 V is the maximum sustained voltage (magnitude) that should be applied to the capacitor. Capacitance, like resistance, can vary with operating temperature. For example, the dielectric might expand or shrink with changes in temperature, which would alter the distance between the plates and thus the capacitance. Overheating due to careless soldering could change the capacitance of a capacitor (permanently) by 5% or more. Also, it is difficult in manufacture to maintain uniform dielectric thickness and various electrical properties (such as relative permittivity) over the required area. Consequently, capacitance of an off-the-shelf capacitor typically is specified only to within 20% of the nominal value. Some have large asymmetric tolerances, such as þ30% to 80%. More accurate capacitors are obtainable but, of course, at higher prices. As a rule, capacitors having mica, glass, or plastic (e.g., polystyrene or polycarbonate) dielectrics exhibit good accuracy, low leakage current through the dielectric, and good temperature stability, whereas those using an impregnated paper dielectric are poorer on those counts. The dielectric in an
8 Capacitance
electrolytic capacitor is a very thin oxide layer, created and maintained by an electrochemical process. Thus an electrolytic capacitor is polarized, with one terminal marked positive, meaning that that terminal must always be at a higher potential than the other. Electrolytic capacitors are typically used to smooth voltages that are always positive, but which have ac components. Figures 8.3 and 8.4 show assorted fixed and variable capacitors. Capacitors are labeled in various ways, as illustrated by Fig. 8.5. The capacitance of capacitor (a) is clearly marked as 470 mF. The marking on capacitor (b) is a common three-digit code for capacitance in picofarads. The first two digits are significant figures and the last is the number of following zeros. The capacitance is 100 pF. The marking on capacitor (c) is the numerical value of the capacitance in mF. The colored-dot code illustrated by capacitor (d) (example colors) is no longer used, probably because no one could ever figure it out. Suffice it to say that there are numerous schemes for indicating the capacitance, maximum voltage rating, and tolerance of a capacitor. You will find some that are not marked at all, probably because the manufacturer could not come up with a sufficiently obscure code. The best way to decipher a particular code on a particular capacitor is to visit the manufacturer’s website. Some capacitors are constructed by depositing metal layers on each side of a thin sheet of a plastic film, such as polyester or polypropylene. The metal layers are the plates and the film is the dielectric. Capacitors in integrated circuits are constructed by laying down a layer of metal, then a layer (a film) of dielectric material, then another layer of metal. Discrete and integrated capacitors fabricated in this manner are called film capacitors or thin-film capacitors. The thickness of the film (the distance between the plates) can be as small as about 1 mm, so sizable capacitances can be attained within reasonable surface areas. A film capacitor, like a film resistor, is a planar device. By analogy with sheet resistance, capacitance of film capacitors often is described in terms of a quantity called sheet capacitance, which is the capacitance per unit area of the capacitor. Sheet capacitance is denoted by Csheet. Thus the capacitance of a film capacitor can be expressed as C¼
er e0 A ¼ A Csheet ; d
(8.7)
8.2 Capacitors
241
(e) (a)
(b)
(c)
(d)
(f) (g)
Fig. 8.3 Fixed capacitors (not to scale): (a) ceramic, (b) mica, (c) tantalum, (d), (e) polypropylene, (f) polystyrene, (g) ceramic chip, (h–l) electrolytic (Photographs courtesy of Rapid Electronics, Ltd)
(h)
(i) (j)
(k)
(l)
(d) (a)
Fig. 8.4 Variable capacitors (not to scale). (a–e) small trimmer capacitors, (f) fourgang air-dielectric tuning capacitor (Photographs (a–e) courtesy of Rapid Electronics, Ltd. (f) courtesy of West Florida Components)
(e)
(b)
(c)
(f)
242
8 Capacitance
470 μF 50 VDC
+
101
+ +
(a)
(b) yellow green
red 0.1
blue
Fig. 8.5 Capacitance markings. In (d), the colors are for illustration only (have no special significance).
white (d)
where A is the surface area. It follows that Csheet ¼
violet
(c)
er e0 : d
i
i
v
(8.8)
For example, if an IC manufacturing facility (a foundry) can deposit layers as thin as 1 mm using a dielectric material having relative permittivity er ¼ 7, that foundry can provide a sheet capacitance of
v
C
(a) non-polarized capacitor
C
(b) polarized capacitor
Fig. 8.6 Circuit-diagram symbols for capacitors
which implies
er e0 ð7Þð8:854 1012 F m1 Þ ¼ d 106 m ffi 62 mF m2 ¼ 62 pF mm2 :
Csheet ¼
dvðtÞ ¼
1 iðtÞdt: C
It follows that
8.3 Terminal Characteristics of an Ideal Capacitor Figure 8.6 shows circuit-diagram symbols for nonpolarized and polarized (electrolytic) capacitors. To avoid distractions from our main purpose, we use the symbol for a non-polarized capacitor almost exclusively. From (8.4), dq dv ¼C ; iðtÞ ¼ dt dt
(8.9)
ðt
1 dvðtÞ ¼ vðtÞ vðt0 Þ ¼ C t0
ðt
iðt0 Þdt0
(8.10)
t0
Eq. (8.10) is usually written 1 vðtÞ ¼ vðt0 Þ þ C
ðt
iðt0 Þdt0
(8.11)
t0
Equation (8.11) shows that a capacitor has memory: The present terminal voltage depends upon past values of the terminal current.
8.3 Terminal Characteristics of an Ideal Capacitor
243
v v1
0
i
t t1
t2
t3
C
t4
+
v –
v2 (a)
i1 t2 0
t4 t
t1
t3
i2
(b)
Fig. 8.7 See Example 8.3
Again, from (8.4), we have i¼
dq dv ¼C : dt dt
(8.12)
Equations (8.11) and (8.12) are the terminal characteristics for an ideal capacitor. In this chapter we assume all capacitors are ideal. More realistic models for capacitors are described in subsequent chapters. Equation (8.12) relates the voltage across a capacitor to the current entering the positive terminal of the capacitor. For economy, we say that (8.12) relates the voltage across a capacitor to the current through the capacitor. By implication, the positive direction of the current is into the positive terminal. Equation (8.12) has several important implications: • Current is nonzero whenever the terminal voltage is changing (when dv/dt is nonzero) and is zero otherwise. A capacitor appears as an open circuit to a constant voltage. • The magnitude of the terminal current is proportional to the rate of change of the terminal voltage. The more rapid the voltage change, the larger the required current.
• Changing the terminal voltage instantaneously would require infinite current. Thus, in physical circuits, the voltage across a capacitor is a continuous function of time.11 In other words, the voltage across a capacitor cannot change instantaneously. • The current through a capacitor is proportional to the capacitance C. More current (or more time) is required to charge a larger capacitor to a specified voltage than is required for a smaller one. A circuit in which all currents and voltages are constant is said to be in dc steady state. If the voltage across a capacitor is constant, the current through the capacitor is zero. Thus, for any circuit in dc steady state, all capacitors in the circuit are effectively open circuits. Example 8.3. Figure 8.7(a) shows a graph of voltage across a capacitor as a function of time. Draw a graph of the current i through the capacitor versus time.
11
Continuity of the voltage across a capacitor also follows from (8.10).
244
8 Capacitance
Solution: Figure 8.7(b) shows the current through the capacitor, given by (8.12). The direction of the current is into the terminal taken as positive in the definition of the voltage v, where, from (8.12), the currents i1 and i2 in Fig. 8.7(b) are the slopes of the lines directly above in Fig. 8.7(a), multiplied by the capacitance C. Thus, i1 ¼
Cv1 ; t1
i2 ¼
Exercise 8.3. The voltage across a 0.1 mF capacitor is given by vðtÞ ¼ V sinð2 p f tÞ; with V ¼ 5V and f ¼ 10 MHz. Obtain an expression for the current through the capacitor. Find the maximum magnitude of the current.
Cðv2 v1 Þ : t4 t2
Exercise 8.2. Figure 8.8 shows a graph of the voltage across a 20 pF capacitor. Draw a graph of the current through the capacitor.
Example 8.5. The current through a 0.5 mF capacitor is given by 0; t < 0; iðtÞ ¼ Iet=t ; t 0; where I ¼ 5 mA and t ¼ 10 ms. Obtain an expression for the current through the capacitor.
Example 8.4. The voltage across a 0.1 mF capacitor is given by vðtÞ ¼ V cosð2 pf tÞ;
Solution: From (8.10), ð I t t0 =t 0 iðt0 Þdt0 ¼ e dt C 0 1 I t 0 t ¼ et =t C 0 i h i Ith t=t ¼ 1e ¼ V 1 et=t ; C
vðtÞ ¼
with V ¼ 10V and f ¼ 1 MHz. Obtain an expression for the current through the capacitor. Solution: From (8.12), dv ¼ 2 pf V C sinð2 pf tÞ dt ¼ I sinð2 pf tÞ;
1 C
ðt
with
iðtÞ ¼ C
V¼
with
It ð5 mAÞð10 msÞ ¼ ¼ 100 V: C 500 nF
I ¼ 2 p f V C ¼ 2 p ð1MHzÞð10VÞð1nFÞ ffi 6:28 A: Exercise 8.4. Figure 8.9 shows a graph of the current through a 5 nF capacitor. The current equals zero for times not shown. Draw a graph of the voltage across the capacitor.
v (mV) 5
12 0
4
5
–5
Fig. 8.8 See Exercise 8.2
7
t (ms)
10
Example 8.6. Refer to Fig. 8.10. What is the voltage vC across the capacitor a very long time after the switch is moved from a to b?
8.3 Terminal Characteristics of an Ideal Capacitor
245 a
i (2mA/div)
b
I0
C
R
+ vC –
t (1 μs/div)
0
Fig. 8.11 See Exercise 8.5
t=0
+ V0
Fig. 8.9 See Exercise 8.4
C –
(a) v(t) = 0, t < 0
R V0
–
+
+
v
v1
–
–
+ C1
C2
v2 –
(b) v1(t) > 0, v2(t) = 0, t < 0
Fig. 8.12 Unrealistic circuit models implying instantaneous changes in capacitor terminal voltages
a
+
t=0
+
b C
vC –
Fig. 8.10 See Example 8.6
Solution: After a sufficiently long time, the capacitor appears as an open circuit (the voltage source is dc), the current through the resistor equals zero, and, by Kirchhoff’s voltage law, the voltage across the capacitor equals the source voltage V0.
Exercise 8.5. Refer to Fig. 8.11, where the current source is constant. What is the voltage vC across the capacitor a very long time after the switch is moved from a to b? Because the voltage across a capacitor cannot change instantaneously, circuit models implying such changes are inconsistent with reality. Figure 8.12 shows two examples of such models, often posed as trick questions on examinations. In Fig. 8.12(a), a battery is suddenly connected (at t ¼ 0) to a capacitor whose terminal voltage equals zero for t < 0. The model implies that the voltage across the capacitor
changes instantaneously, which would require infinite current. Omitted from the model is the resistance of the connecting wires (among other things). Including those parameters would make the model more realistic. In Fig. 8.12(b), a charged capacitor is suddenly connected (at t ¼ 0) to an uncharged capacitor. This model also implies that the voltages across the capacitors must change instantaneously, which would require infinite current. Moreover, comparing the initial and final voltages across the capacitors shows that energy somehow disappears from the circuit, in spite of the fact that there are no energy-loss mechanisms (e.g., resistors) in the model.12 Again, the resistance of the connecting wires is omitted from the model. Including that resistance (no matter how small, so long as it is non-zero) would make the model realistic and would account for the lost energy. Often, it is possible and even helpful to use unrealistic models similar to those in Fig. 8.12 for qualitative analysis (for discerning or describing how a circuit works) and even for calculations that do not require exact expressions for terminal current or voltage,13 but obtaining correct expressions for currents or voltages
12
Section 8.9 treats energy stored in the electric field in a capacitor. 13 See Section 8.10.8 for an example.
246
8 Capacitance
as functions of time requires using models consistent with physical reality. From another point of view, the circuit in Fig. 8.12(a) is unrealistic because the internal resistance of the source (battery) appears to be zero. All physical sources possess internal resistance. Whenever you encounter a voltage source having no series resistance or a current source having no parallel resistance in a circuit, be aware that any quantitative analysis of the circuit might lead to incorrect results. Exercise 8.6. What is wrong with the circuit (model) in Fig. 8.13, where i0 > 0 for all time? Is it possible to find a value for vC at any time?
a resistor having resistance R. By Kirchhoff’s current law, we have for t > 0 that C
dv v dv v þ ¼0) ¼ : dt R dt RC
(8.13)
According to (8.13), the voltage v and its derivative have the same mathematical form (are proportional). The function having that property is the exponential function. You can show by substitution that the solution to (8.13) is t vðtÞ ¼ K exp ; t > 0; RC
(8.14)
For t ¼ 0þ, (8.14) gives v(0þ) ¼ K, so we have
8.4 Charge-Discharge Time Constant A circuit composed of only resistors and one capacitor is called an RC circuit. In this section, we obtain expressions for currents and voltages in an RC circuit subjected to an abrupt change in excitation. The following notation is helpful: Let t0 denote a particular time. Then t0 and t0 þ denote times infinitesimally before and after t0. For example, if t ¼ 0 denotes the time at which switch is closed, then t ¼ 0 is the time just before closure and t ¼ 0þ is the time just after closure. Refer to Fig. 8.14, where a capacitor that has been previously charged to a voltage V0 is connected at t ¼ 0 to
t vðtÞ ¼ vð0þ Þ exp ; t > 0: RC
(8.15)
From the problem statement, we know that v(0) ¼ V0. We also know that the voltage across a capacitor cannot change instantaneously. It follows that v(0þ) ¼ V0 and thus t vðtÞ ¼ V0 exp ; t > 0; RC
(8.16)
as illustrated by Fig. 8.14. Equation (8.16) usually is written
R
t vðtÞ ¼ V0 exp ; t > 0; t
(8.17)
t ¼ RC:
(8.18)
+ i0
vC
C
–
Fig. 8.13 See Exercise 8.6
v(t) t=0
V0 +
R
C
v(t) –
v(0) = V0 0
t 0
Fig. 8.14 The voltage across a charged capacitor decreases exponentially with time after the capacitor is connected to a resistor
where
is called the time constant for the circuit consisting of the capacitor and resistor. The time constant determines how fast the capacitor discharges through the resistor. Because e1 ffi 0:37, the voltage across the capacitor drops to 37% of its initial value in a time equal to one time constant. Similarly, e3 ffi 0:05, so the voltage drops to 5% of its initial value in a time equal to three time constants. You can show that the voltage is less than 1% of its initial value when t equals five time constants.
8.4 Charge-Discharge Time Constant
247
where t ¼ RC is the time constant for the circuit. The voltage v(t) across the capacitor is given by
Exercise 8.7. In the circuit shown in Fig. 8.14, C ¼ 100 nF and the voltage v(t) has dropped to half of its initial value 7 ms after the switch is closed. Find the resistance R.
v ð t Þ ¼ v ð 0Þ þ ¼0þ
Now refer to Fig. 8.15, where a capacitor that is initially uncharged is connected through a resistor to a constant voltage source at t ¼ 0. Because the capacitor is initially uncharged, v(0) ¼ 0. By Kirchhoff’s voltage law Ri þ vð0 Þ þ
1 C
ðt 0
iðt0 Þdt0 ¼ Ri þ
1 C
ðt 0
iðt0 Þdt0 ¼ V0 : (8.19)
Differentiating once with respect to time and rearranging terms gives di i ¼ ; dt RC which we now know implies that t i ¼ ið0þ Þ exp ; t > 0: RC
(8.20)
From (8.19) 1 Rið0 Þ þ C þ
ð 0þ 0
iðt0 Þdt0 ¼ Rið0þ Þ ¼ V0 ) ið0þ Þ ¼
V0 : R
Thus, i¼
t V0 exp ; t > 0; R t
v(t) t=0
V0
R
V0 t
1 C ðt
ðt
iðt0 Þdt0 0 t exp dt0 ; t 0 0
which yields h t i ;t 0 vðtÞ ¼ V0 1 exp t
(8.21)
as illustrated in Fig. 8.15. Again, the time constant determines how fast the capacitor charges when connected to a constant source through a resistor. Because 1 e1 ffi 0:63, the voltage equals about 63% of its final value V0 for t ¼ t ¼ RC. You can show that for t ¼ 3t and t ¼ 5t the voltage equals about 95% and 99%, respectively, of V0. In general, the time constant for a circuit consisting of any number of resistors and one capacitor is the product of the capacitance of the capacitor and the The´venin equivalent resistance seen at the terminals of the capacitor. The time constant for charging and discharging a capacitor and the mathematical forms of the voltages during charging and discharging are important. You will encounter these concepts in many guises and countless times during your college days and most likely during your career as an electrical engineer. Study Fig. 8.14 and Equation (8.17) and Fig. 8.15 and Equation (8.21) until they are firmly fixed in your mind. Commit to memory that the time constant is a measure of how fast a capacitor can charge and discharge, and that the time required for a capacitor having capacitance C to fully discharge or fully charge through a resistor having resistance R is approximately 5RC, where fully means a discharge to less than 1% of the initial value or a charge to more than 99% of the final value.
+ +
V0
–
C i
v (t) –
v(0) = 0 0
t 0
Fig. 8.15 When an uncharged capacitor is connected through a resistor to a constant voltage V0, the voltage across the capacitor increases exponentially toward the voltage V0
Exercise 8.8. In the circuit shown in Fig. 8.15, R ¼ 50 kO, V0 ¼ 5 V, and the switch is closed at t ¼ 0. At t ¼ 1 ms the voltage v(t) equals 2 V. Find the capacitance C.
248
8 Capacitance
Exercise 8.9. In Fig. 8.16, the switch is moved at t ¼ 0 from position 0 to position 1 and left there until the capacitor is fully charged. The switch is then immediately moved to position 2 until the capacitor is fully discharged. (a) How long must the switch reside in each position? (b) Draw a graph (a neat, fully labeled sketch) of the voltage v(t) across the capacitor for t 0.
which implies t iðtÞ ¼ K exp : RC The voltage across the capacitor must be continuous, so the voltage across the resistor (left to right) at t ¼ 0 must be V1 – V0. It follows that V1 V0 ¼K R t V 1 V0 ) iðtÞ ¼ exp ; t > 0: R RC ið0þ Þ ¼
Example 8.7. In Fig. 8.17, the capacitor is initially charged such that v(t) ¼ V0 for t < 0. The switch is then closed at t ¼ 0. (a) Obtain an expression for the voltage v(t) for t > 0. (b) Draw graphs (neat, fully labeled sketches) of the voltage v(t) for t 0 and for (i) V0 < V1 and (ii) V0 > V1.
From (8.11),
t0 exp dt0 RC 0 t ¼ V1 ðV1 V0 Þ exp ; t > 0: RC ð8:22Þ
V1 V0 vðtÞ ¼ V0 þ RC
Solution: (a) Kirchhoff’s voltage law gives 1 R i þ vð0Þ þ C
ðt
iðt0 Þdt0 ¼ V1 :
0
Differentiating once with respect to time and rearranging terms yields di 1 ¼ i; dt RC
0
1
(b) Figure 8.18 shows graphs of the voltage v(t) given by (8.22), where the solid line is for V0 < V1 and the dashed line is for V0 > V1. In either case, the transition from V0 to V1 is essentially complete in about five time constants. The relation (8.22) obtained in Example 8.7 above can be written in a more general and useful form as vðtÞ ¼ vð1Þ ½vð1Þ vð0þ Þ expðt=tÞ; t > 0:
2 +
+
v (t)
C
–
(8.23)
R1 V0
ðt
V0 = 5V, C = 100 pF R1 = 100 kΩ, R2 = 500 kΩ
R2
–
V0
V1
V0
V1
Fig. 8.16 See Exercise 8.9
v (t) t=0
R +
+ V1
–
Fig. 8.17 See Example 8.7
i
C
v(t)
0
1
2
3 t RC
–
Fig. 8.18 See Example 8.7
4
5
8.4 Charge-Discharge Time Constant
249
The time constant t in (8.23) is given by t ¼ RT C;
(8.24)
where RT is the The´venin equivalent resistance seen at the terminals of the capacitor. Equation (8.23) can be applied to any voltage in any circuit consisting of any number of resistors and one capacitor, where the initial and final voltages are given or can be deduced. Equation (8.23) describes the transition of the voltage across a capacitor from an initial value v(0þ) toward a final value v(1). Example 8.8. Refer to Fig. 8.19. The switch is open for t < 0 and closed at t ¼ 0. (a) Obtain an expression for the voltage vC (t). (b) Use (8.23) to obtain an expression for the voltage v1 (t). (c) Show that your answers satisfy v1 (t) þ vC (t) ¼ V0 (Kirchhoff’s voltage law) for t > 0. Solution: (a) Because the switch was open for t < 0, vC ð0 Þ ¼ 0. Because the voltage across a capacitor cannot change instantaneously, vC ð0þ Þ ¼ 0. After the switch has been closed for a long time, the capacitor appears as an open circuit, and v C ð1Þ ¼
For t ! 1, v1 ð1Þ ¼ V0 vC ð1Þ R2 V0 R1 V0 ¼ ¼ V0 R1 þ R2 R1 þ R2 Thus t R1 V0 R1 V0 v1 ðtÞ ¼ V0 exp R1 þ R2 R1 þ R2 t t R1 V0 R2 V0 ¼ þ exp ; t > 0 R1 þ R2 R1 þ R2 t Note that v1 ð0 Þ ¼ 0, whereas v1 ð0þ Þ ¼ V0 , which illustrates the fact that a current or a voltage other than the voltage across a capacitor can change instantaneously. (c) t R1 V0 R2 V0 þ exp R1 þ R2 R1 þ R2 t t i R2 V0 h 1 exp þ R1 þ R2 t R1 V0 R2 V0 þ ¼ V0 ¼ R1 þ R2 R1 þ R2
v1 ðtÞ þ vC ðtÞ ¼
R2 V0 : R 1 þ R2
The time constant for t > 0 is given by t ¼ RT C; where RT ¼ R1 kR2 ¼
R1 R2 R 1 þ R2
is the The´venin equivalent resistance at the terminals of the capacitor. Thus, from (8.23) t vC ðtÞ ¼ vC ð1Þ ½vC ð1Þ vC ð0þ Þ exp t t i R2 V0 h 1 exp ¼ ; t > 0: R 1 þ R2 t
Again, (8.23) is applicable not only to the voltage across a capacitor, but to any node voltage or any branch current in any circuit consisting of any number of resistors and one capacitor, where the initial and final voltages are given or can be deduced. If used to express a branch current, (8.23) becomes t iðtÞ ¼ ið1Þ ½ið1Þ ið0þ Þ exp ; t > 0: t (8.25)
+
v1
–
iC
þ
(b) From part (a), vC ð0 Þ ¼ 0. By Kirchhoff’s voltage law, þ
þ
v1 ð0 Þ ¼ V0 vC ð0 Þ ¼ V0 :
+
V0
R1
–
Fig. 8.19 See Example 8.8
+
R2
C
vC –
250
8 Capacitance R1
Example 8.9. Refer to Fig. 8.19. Use (8.25) to obtain an expression for the current iC (t). þ
Solution: We deduce that iC ð0 Þ ¼ V0 =R1 and iC ð1Þ ¼ 0. From (8.25), iC ðtÞ ¼
t V0 exp ; t ¼ ðR1 kR2 ÞC; t > 0: R1 t
Exercise 8.10. Which of the currents and voltages labeled in Fig. 8.20 cannot change instantaneously? The next example illustrates how (8.23) can be used to construct a solution to a problem involving multiple switching times and/or a piecewise-constant source. Example 8.10. Refer to Fig. 8.21, where the source voltage vS equals zero for times not shown. Construct a graph of the voltage vC (t) across the capacitor for 2 ms t 8 ms. Solution: Let t ¼ RC ¼ 500 ms; V0 ¼ 100 mV; tn ¼ n ms. We use (8.23) to piece together the response vC (t). The source voltage equals zero for t 0, so vC ðtÞ ¼ 0; t 0:
(8.26)
The first non-zero segment of vS equals 200 mV ¼ 2V0 for 0 < t t2 , where t2 ¼ 2 ms. The initial value of the response is vð0þ Þ ¼ 0 and the response approaches vð1Þ ¼ 2V0 . Thus, from (8.23) t vC ðtÞ ¼ 2V0 ð2V0 0Þ exp t h t i ¼ 2V0 1 exp ; t (8.27) 0 < t t2 : The next segment of vS extends from t ¼ t2 þ to t ¼ t3. The response in that interval is initially equal to the final value vC ðt2 Þ of the response in the previous interval and approaches 200 mV ¼ 2V0 . Thus, for t2 < t t3 , we use
+ v1 –
iC
i2
+
vS
+ –
R2
C
i1
vC –
Fig. 8.20 See Exercise 8.10
and (8.23) with vC ð0þ Þ ¼ vC ðt2 Þ vC ð1Þ ¼ 2V0 . We must also shift the response to the beginning time t2 for the interval to which it applies. This gives vC ðtÞ ¼ 2V0 ½2V0 vC ðt2 Þ tt 2 exp ; t2 < t t3 ; t
(8.28)
where, from (8.27) h t i 2 : vC ðt2 Þ ¼ 2V0 1 exp t The next segment of vS extends from t3 to t4. The response in that interval is initially equal to the final value vC ðt3 Þ of the response in the previous interval and approaches 300 mV ¼ 3V0 . Thus, for t3 < t t4 , we use (8.23) with vC ð0þ Þ ¼ vC ðt3 Þ and vC ð1Þ ¼ 3V0 . We must also shift the response to the beginning time t3 for the interval to which it applies. This gives vC ðtÞ ¼ 3V0 ½3V0 vC ðt3 Þ tt 3 exp ; t3 < t t4 ; t
(8.29)
where, from (8.28) vC ðt3 Þ ¼ 2V0 ½2V0 vC ðt2 Þ t t 3 2 exp : t Continuing in this way, we obtain vC ðtÞ ¼ V0 ½V0 vC ðt4 Þ tt 4 ; t4 < t t6 ; exp t
(8.30)
8.4 Charge-Discharge Time Constant
251
vS (mV) R
vS
+ –
300 C
+
200
vC
100
–
t (ms)
0 1
–100
R = 100 kΩ, C = 5nF
2
3
5
4
6
–200
Fig. 8.21 See Example 8.10
400 300 200 100 0 –100 –200 –300 –2
–1
0
1
2
3 t (ms)
5
6
7
8
vC (mV)
vS (mV)
Fig. 8.22 See Example 8.10
4
S2
where, from (8.29) t t 4 3 ; vC ðt4 Þ ¼ 3V0 ½3V0 vC ðt3 Þ exp t and
R1
+ –
S1
V0
R2
+ C
vC –
Fig. 8.23 See Example 8.11
vC ðtÞ ¼ 0 ½0 vC ðt6 Þ tt 6 exp ; t6 < t; t
(8.31)
When using (8.23) or (8.25) to express a voltage or current for multiple switching times, be sure to use the correct time constant for each interval.
where, from (8.30) vC ðt6 Þ ¼ V0 ½V0 vC ðt4 Þ t t 6 4 exp : t Figure 8.22 shows a graph of the response.
Example 8.11. In Fig. 8.23, both switches are open for t < 0, and vC ð0 Þ ¼ 0. Switch S1 is closed at t ¼ 0 and switch S2 is closed at t ¼ t1. Obtain an expression for the voltage vC(t) across the capacitor.
252
8 Capacitance
t1 vC ðtÞ ¼ V0 V0 V0 1 exp t1 t t1 exp ¼ V0 V0 t2 t1 t t1 exp ; exp t1 t2
Solution: We use (8.23) (twice). We are given vC ð0 Þ ¼ 0, which implies vC ð0þ Þ ¼ 0, because the voltage across a capacitor is continuous. For 0 < t t1 , the voltage vC (t) rises toward V0 with time constant given by t1 ¼ ðR1 þ R2 ÞC:
t2 ¼ R1 C; t > t1 :
Thus for 0 < t t1 , vð1Þ ¼ V0 , and (8.23) becomes
Therefore 8 > < 0; t < 0 vC ðtÞ ¼ V0 ½1 expðt=t1 Þ; 0
: 1 expðt=t1 Þexp½ðt t1 Þ=t2 ; t > t1
t vC ðtÞ ¼ V0 1 exp ; t1 t1 ¼ ðR1 þ R2 ÞC; 0 < t t1 :
where
For t1 < t < 1, the resistor R2 is bypassed by a short circuit, so the time constant is given by
t1 ¼ ðR1 þ R2 ÞC; t2 ¼ R1 C:
t2 ¼ R1 C:
8.5 Capacitors in Series and Parallel
If we take t1 as the time origin for the second segment, the initial and final values of vC(t) are given by
t1 vC ð0 Þ ¼ V0 1 exp t1 þ
Figure 8.24a shows n capacitors in series. Because the same current passes through each capacitor, Kirchhoff’s voltage law gives
;
1 v¼ C1
ðt 1 ðt
ð 1 1 t 0 0 þ i ðt Þ dt þ þ i ðt0 Þ dt0 C2 1 Cn 1 ðt 1 1 1 ¼ þ þ þ i ðt0 Þ dt0 ; C1 C2 Cn 1 (8.32)
vC ð1Þ ¼ V0 : We then reset the time origin to zero (delay the response by t1) and obtain
+
+
v
C1
–
i
C2
L
CN
⇒
Ceq i
1 1 1 L 1 = + + + CN Ceq C1 C2
+
v –
v
– (a) capacitors in series
+
Fig. 8.24 Capacitors in (a) series and (b) parallel
i ðt0 Þ dt0
C1 i
C2
L CN
⇒
v
– (b) capacitors in parallel
Ceq i
Ceq = C1 + C2 +L +CN
8.6 Leakage Resistance
253
which can be written ð 1 t i ðt0 Þ dt0 ; Ceq 1 1 1 1 1 ¼ þ þ þ : Ceq C1 C2 Cn
2C
v¼
C
(a)
(8.33)
2C
Thus a series connection of capacitors is equivalent at the terminals to a single capacitor having capacitance Ceq given by (8.33). Combining capacitors in series yields an equivalent capacitance that is smaller than the smallest of the individual capacitances. Figure 8.24b shows n capacitors in parallel. Because the same voltage appears across each capacitor, Kirchhoff’s current law gives dv dv dv þ C2 þ þ Cn dt dt dt dv ¼ ðC1 þ C2 þ þ Cn Þ ; dt
C
C
i ¼ C1
2C
C
2C
C
C
(b)
Fig. 8.25 See Example 8.12
3C 2C
2C
a
(8.34)
C
2C
b
which can be written
Fig. 8.26 See Exercise 8.11
i ¼ Ceq
dv ; dt
Ceq ¼ C1 þ C2 þ þ Cn :
(8.35)
Therefore the equivalent capacitance of n capacitors in parallel is the sum of the individual capacitances. Combining capacitors in parallel yields an equivalent capacitance that is larger than the largest of the individual capacitances. Example 8.12. Find the equivalent capacitance at the terminals of the circuit shown in Fig. 8.25(a). Solution: See Fig. 8.25(b). First combine the two rightmost capacitors using (8.35). Then combine the two series capacitors using (8.33). Finally, combine the remaining two parallel capacitors, again using (8.35).
In practical problems, we rarely need to find the equivalent capacitance of more than two capacitors in series or parallel. Even this need arises primarily in only two circumstances. One is in modeling, where various approximations occasionally reduce more complex arrangements to a point where remaining capacitances (or other elements) appear in series or parallel. The other is when a small variable capacitor is used in parallel with a larger one to allow trimming (fine adjustment) of the total capacitance. Otherwise, few if any circuits are designed using capacitors in series or parallel (where it is cheaper and easier to use one). Note: The double-bar notation is used only for resistors in parallel. Do not use the notation C1 k C2 to denote capacitors in parallel because the implied method for obtaining the equivalent capacitance of two capacitors in parallel is incorrect. Use C1 þ C2 instead.
8.6 Leakage Resistance Exercise 8.11. Refer to Fig. 8.26. Obtain an expression for the equivalent capacitance at the terminals a–b.
Dielectrics used in capacitors have resistivities that are on the order of 1to100 MO cm. Thus a dielectric is not a perfect insulator and some conduction current passes
254
8 Capacitance
between the plates. This current is called leakage current and the resistance of the dielectric is called leakage resistance. From Chapter 2, the resistance of a sample of homogeneous material having length l, cross-section area A, and resistivity r is given by R¼
Example 8.13. Refer to Fig. 8.27(a), where V0 is constant and the capacitors are initially uncharged, such that v1 ð0Þ ¼ v2 ð0Þ ¼ 0. Obtain expressions for the voltages v1 ; v2 a very long time after the switch is closed.
rl : A
Solution: Because V0 is constant, the current through the capacitors equals zero for t ! 1. However, from Kirchhoff’s voltage law,
Thus the leakage resistance for a parallel-plate capacitor is given by Rleak ¼
rd ; A
v1 þ v2 ¼ V0 ;
(8.36)
so the voltages across the capacitors are nonzero. For t ! 1, the voltages are determined by the leakage resistances, as shown in Fig. 8.27(b), and not by the capacitances. The circuit in Fig. 8.27(b) is a voltage divider, and in dc steady state all of the current I passes through the resistors (none through the capacitors). It follows that
where A is the area of one plate (the cross-sectional area of the dielectric), r is the resistivity of the dielectric, and d is the separation of the plates (the length of the dielectric). Leakage resistance in modern capacitors ranges from about 1 MO to almost 1 TO ð1012 OÞ. For capacitors with the same geometry and identical dielectric and plate materials, leakage resistance is inversely proportional to capacitance; that is, from (8.36) and (8.5), Rleak
r e0 e r ¼ : C
v1 ¼
R1 V0 R2 V0 ; v2 ¼ : R1 þ R2 R1 þ R2
(8.38)
(8.37) If we do not know the leakage resistance (the usual case), but know the dielectric materials, we can estimate the leakage resistances using (8.37):
Equation (8.37) shows that leakage resistance decreases with increasing capacitance. It follows that leakage current generally increases with capacitance, although a large capacitor having a very good (highresistivity) dielectric might exhibit lower leakage than a smaller capacitor having a poor dielectric.
R1 ¼
r1 e 0 e 1 r e0 e2 ; R2 ¼ 2 ; C1 C2
in which case (8.38) becomes V0 ; 1 þ C1 r2 e2 =ðC2 r1 e1 Þ V0 v2 ¼ : 1 þ C2 r1 e1 =ðC1 r2 e2 Þ
Exercise 8.12. Would including the leakage resistances of the capacitors in Fig. 8.12 make the circuit models realistic? Explain how or why not.
+ –
Fig. 8.27 See Example 8.13
V0
v1 ¼
+ v1 –
+ v2 –
C1
C2
+ –
(a)
V0
R1
R2
+ v1 –
+ v2 –
C1
C2 I
(b)
8.7 Stray and Parasitic Capacitance; Capacitive Coupling
255
If the capacitors are of the same type (same dielectric) and are precise, then r1 ¼ r2 , e1 ¼ e2 and v1 ¼
C2 V0 C1 V0 ; v2 ¼ : C 1 þ C2 C 1 þ C2
In addition to shunt leakage resistance, physical capacitors exhibit series resistance due partly to the leads (if long), partly to conduction in the plates, and partly to loss mechanisms in the dielectric that are manifested externally as resistance. The total series resistance is important at high frequencies and high switching rates, as occur in modern digital computers, and also in large capacitors used to smooth the supply voltage in some power supplies, where the power dissipated by the series resistance generates heat and speeds aging of the capacitor.
8.7 Stray and Parasitic Capacitance; Capacitive Coupling Like resistance, capacitance is intentionally introduced in most circuits to achieve certain ends. But whether we like it or not, capacitance is present wherever current-carrying conductors are separated by an insulating medium. For example, capacitance exists between wires on a circuit board and between wires strung on utility poles. Capacitance that is more or less widely distributed in a circuit, arising, for example, from parallel conductors on the same or opposite sides of a printed-circuit board or from conductors near ground planes, usually is called stray capacitance. Unintentional, more localized capacitance also exists in devices such as diodes and
transistors because of the geometries of those devices. Such capacitance often is called junction capacitance because of its association with device structures called junctions. Capacitance in passive elements such as resistors and inductors often is called residual capacitance. Localized unintentional capacitance, such as residual capacitance and junction capacitance in electronic devices, often is called parasitic capacitance. Stray and parasitic capacitance can be significant, depending upon the geometry involved and the rate at which the relevant voltage varies. Parasitic capacitance in transistors limits the speed with which a transistor can respond to rapidly changing voltages and thereby limits the frequency response of transistor amplifiers, although the limit can be quite high. Stray and parasitic capacitance can be especially troublesome in computers and in microwave circuits, where voltages change very quickly. Stray capacitance can be important between telephone lines that are parallel over great distances, even though the voltages might not change as quickly. If not prevented or properly accounted for, stray and parasitic capacitance can prevent a circuit from working as intended. For example, suppose that a certain application calls for a resistive voltage divider, as shown in Fig. 8.28(a), where vS ðtÞ ¼ V0 cosð2pf0 tÞ. If the frequency f0 of the source vS ðtÞ is high enough, the residual (or parasitic) capacitances of the resistors come into play, as shown in Fig. 8.28(b). We are at this point unprepared for detailed analysis of the circuit in Fig. 8.28(b), but you can see that for a time-varying source voltage vS ðtÞ, the actual output voltage vb ðtÞ will differ from the desired (or intended) output voltage va ðtÞ. If it is known that that residual capacitance will be significant in a resistive voltage divider, a designer can compensate for that by intentionally introducing capacitances C1 ; C2 (as in Fig. 8.28(b) that are much larger than the stray capacitances, and then designing the resistive-capacitive
C1
Fig. 8.28 Residual capacitance can affect resistive voltage dividers at high frequencies
vS (t) +–
R1
+ R2
va (t)
vS (t) +–
R1
+ C2
vb (t) –
– (a) desired
R2
(b) actual
256
8 Capacitance D
wire-to-ground capacitance per cm of length and the total capacitance if the length of the pair of wires is 4 cm.
Cww 2r conductors Cwg
Solution: From Chapter 2, the radius of AWG 24 wire is
h
Cwg
1 24 r ¼ ð8:251 mmÞ exp 2 8:628
ground
Fig. 8.29 Stray conductor-to-conductor and conductor-toground capacitance
voltage divider accordingly. Such a voltage divider is said to be compensated. Parallel conductors and conductors parallel to ground planes can be significant sources of stray capacitance. Refer to Fig. 8.29, which represents parallel conductors in a vacuum (or air) above a ground plane; for example, a two-conductor power transmission line strung on utility poles above ground, or a smaller two-conductor wire running parallel to a grounded metal chassis. The wire-to-wire capacitance and the wire-to-ground capacitance per meter are given by14 2 2
331
DCww d 6 6 77 ¼ pe0 4ln4 qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi55 ; Dl 2 r 1 þ 0:25ðd=hÞ
DCwg 2h r 1 ; ¼ 2pe0 ln Dl r
¼ 256 mm: From (8.39), with r ¼ 256 mm; d ¼ 1 mm; h ¼ 1 cm, 2 2
331
DCww d 6 6 77 ¼ pe0 4ln4 qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi55 Dl 2 r 1 þ 0:25ðd=hÞ ¼ 0:204 pF cm1 ;
DCwg 2h r 1 ¼ 2pe0 ln Dl r ¼ 0:128 pF cm1 : The total capacitance per unit length is given by DC DCww DCwg þ ffi 0:332 pF m1 ; ¼ Dl Dl Dl
ð8:39Þ
where d is the center-to-center distance between the conductors, h is the distance of the conductors from the ground plane, r is the radius of the conductors, and e0 ¼ 8:842 1012 F m1 is the permittivity of air. Example 8.14. A pair of straight AWG 24 copper wires are parallel to each other and to a metal chassis. The distance between the wires is 1 mm and the distance of the pair from the chassis is 1 cm. Calculate the wire-to-wire and
14 Corcoran, George F., and Henry R. Reed, Introductory Electrical Engineering, Wiley, New York, 1957, pp 419–426.
so the capacitance of a 4-cm length of wire is C ffi 1:33 pF: As you can see, wires a few or more cm in length can introduce a few picofarads of stray capacitance. Such capacitance limits the rate at which the voltage across a load can change. For example, if a 4 cm length of the conductors of this example drives a 10 kO load, the effective time constant due to the wire-to-ground capacitance alone is about 13 ns, which means that the time required for the load voltage to change from one value to another is approximately 65 ns. This means the load voltage can switch between two levels no faster than about
8.7 Stray and Parasitic Capacitance; Capacitive Coupling
257
v1 i1
C
i2 t
+ R1
v1 –
+ R2
v2 dv1 dt
–
t
v2 = R2 i2 + R2 C
dv1 dt
R2 i2
Fig. 8.30 Illustrating one possible effect of stray capacitive coupling. (Adapted from Horowitz, Paul et al. 1995.)
15 million times per second. If we are talking about a digital communication system, for example, we could transmit no more than a few million bits per second over the line to the load, which would be unacceptably slow in today’s world. Equations (8.39) ignore whatever structures support the wires, insulation surrounding the wires, and connections at the ends of the wires. They should not be regarded as accurate relations for real-world circuits, in which many wires of various sizes run in many directions, at various distances from each other and from ground planes. A circuit designer will not attempt to actually calculate stray capacitance using (8.39), but will be guided by relations embodied in those expressions. For example, increasing the distance d between wires, decreasing the radius r of wires, and increasing the distances from ground planes all act to decrease stray capacitance. The relative permittivity of an insulating material cannot be less than unity, so binding the wires to each other with an insulating material can increase wire-to-wire
t
capacitance. Thus, for example, using the smallest wire necessary, using insulating material (if required) having a low relative permittivity, and avoiding long runs near ground planes and other wires can help limit stray wiring capacitance. One of the great advantages of integrated circuits is their microscopic size. Conductors are extremely short and have extremely small cross-sectional area. Thus stray wiring capacitance in an integrated circuit can be quite small, even though the distances between conductors are also microscopic. Sometimes, stray capacitive coupling in a circuit can induce the derivative of a signal in one conductor into a neighboring conductor, as illustrated by Fig. 8.30. In absence of capacitive coupling, the voltage v2 across the resistor R2 equals R2 i2 . In presence of stray capacitive coupling, as indicated by the dashed capacitor, Kirchhoff’s current law at the node joining the capacitor to the resistor R2 gives d ðv2 v1 Þ v2 þ i2 ¼ 0 R2 dt dv2 dv1 þ R2 C : ) v2 ¼ R2 i2 R2 C dt dt
C
258
8 Capacitance
In presence of capacitive coupling, the voltage v2 contains a term proportional to the derivative of the voltage v1. If the voltage v1 varies much more rapidly than the voltage v2, then (on average)
CT ¼ capacitance at actual temperature T; C0 ¼ capacitance at reference temperature T0 ðusually; 25 CÞ:
dv1 dv2 : dt dt
Thus the capacitance at temperature T is approximated as
It follows that v2 ffi R2 i2 þ R2 C
where
CT ¼ C0 ð1 þ a DT Þ ¼ C0 ½1 þ a ðT T0 Þ: dv1 ; dt
which shows that a voltage proportional to the derivative of v1 is superimposed on the (desired) voltage R2 i2 , again as illustrated (qualitatively) by Fig. 8.30. Usually, such coupling is undesirable and must be minimized by shielding and careful conductor layout. If shielding and conductor layout do not eliminate the problem, and if v1 varies much more rapidly than v2, then a bypass capacitor in parallel with R2 might reduce the induced interference to an acceptable level. Stray capacitance and capacitive coupling are difficult to compute for complex geometries, such as exist in modern circuits, but a general knowledge of origins and effects of stray capacitance and capacitive coupling can help keep a circuit designer out of trouble.
Manufacturers’ commonly specify the temperature coefficient in parts per million (ppm), in which case (8.41) becomes CT ¼ C0 1 þ appm 106 ðT T0 Þ ;
(8.42)
where the unit of appm is K1 or ð CÞ1 . It does not matter which unit is used, because the numerical value of the difference T T0 is the same, whether the temperatures are expressed in Kelvin (K) or degrees Celsius. Example 8.15. The capacitance and temperature coefficient for a certain capacitor at 25 C are 50 nF and 700 ppm, respectively. Find the capacitance at 65 C. Solution: From (8.42), C35 ¼ 50 nF 1 þ 70 106 ð65 25Þ ¼ 51:4 nF:
8.8 Variation of Capacitance with Temperature For most dielectric materials, relative permittivity varies with temperature, so the capacitance of capacitors made from those materials varies with temperature. Manufacturers describe the relation of capacitance to temperature in mainly one of two ways. For some materials, the variation of capacitance with temperature is approximately linear. In such cases, manufacturers data sheets give a temperature coefficient of capacitance (TCC) a, defined by CT C0 1 DC a¼ ; ¼ ðT T0 ÞC0 C0 DT
(8.41)
(8.40)
For many dielectric materials, the variation of capacitance with temperature is nonlinear, as illustrated by the hypothetical graph in Fig. 8.31. The horizontal axis is temperature and the vertical axis is the percent deviation of the capacitance from the capacitance at 25 C, given by DC C C25 100 ¼ 100: C25 C25 For T ¼ 25 C, C ¼ C25 and the deviation equals zero. The deviation is within 5% for approximately 5 C T 160 C. Thus a specification of 5%
8.8 Variation of Capacitance with Temperature
259 10 5 0 –5 –10
ΔC ( % ) C25ºC –15 –20 –25 –30 –35
Fig. 8.31 Variation of capacitance with temperature (hypothetical example)
–40 –75
–50
–25
0
25
50 75 T (ºC)
100
125
150
175
Table 8.1 Variation of capacitance with temperature for various dielectric materials (Courtesy of AVX Corporation) Dielectric Ceramic Mica Polyester PolyPolyPolystyrene Tantalum Aluminum (NP0) carbonate propylene electrolytic Capacitance 1 pF – 100 1 pF – 90 1 nF – 10 1 pF – 100 47 pF – 47 100 pF – 27 10 nF – 1000 500 nF – 10 range nF nF mF nF nF nF mF mF 55 þ 85 55 þ 125 55 þ 125 55 þ 125 55 þ 85 55 þ 70 55 þ 125 40 þ 85 Temp. range ( C) 0.4 þ 1.8 12 2 2.5 1 8 10 DC=C25 C ð%Þ 0.3
Table 8.2 Definition of codes for variation of capacitance with temperature Minimum temperature ð CÞ X 55 Y 30 Z þ10
Maximum temperature ð CÞ 2 þ45 4 þ65 5 þ85 6 þ10 7 þ125
Change in capacitance with temperature ð%Þ A 1 B 1.5 C 2.2 D 3.3 E 4.7 F 7.5 P 10 R 15 S 22 T þ 22, 33 U þ 22, 56 V þ 22, 82
would be accompanied by the temperature range 5 C T 160 C. Table 8.1 shows typical variations for various dielectric materials. For example, for polyester, the variation of capacitance with temperature can be as much as 12% for the temperature range 55 C T 125 C, whereas for polycarbonate, it is no more than 2% over the same range.
To standardize such specifications, the industry developed the code defined by Table 8.2. The code consists of three characters: A letter (X, Y, or Z), a number (2, 4.5, 6, or 7), and another letter (one of A–F, P, R, S–V); for example, X7R. The First letter and the number specify a temperature range and the last letter specifies the temperature variation within that range. For example, the X7 in X7R specifies the temperature range 55 to 125 C and the R means that the capacitance will vary by no more than 15% from the nominal value over that range. Exercise 8.13. Specify the tolerance and temperature range corresponding to each of the following designations: X5R, Y5V, Z5U.
Exercise 8.14. List the designations for the capacitors that could replace a Y5U capacitor based upon specifications of only capacitance and tolerance alone.
260
8 Capacitance
In circuit-simulation programs, dependence of capacitance on temperature often is approximated using a quadratic function of temperature of the form C ¼ C0 þ a DT þ bðDT Þ2 ; DT ¼ T T0 ;
energy for later release is what gives a capacitor electrical memory. The instantaneous power dissipated in a capacitor having capacitance C is given by
(8.43)
where T is temperature ð CÞ, T0 is a reference temperature (often, 25 C), and C0 is the capacitance at the reference temperature. The coefficients a ðF K 1 Þ and b ðF K 2 Þ are called the first temperature coefficient and the second temperature coefficient, respectively. Pspice and other simulation programs allow a user to specify the temperature coefficients. Variation of capacitance with temperature is an important consideration in circuit design. Indeed, capacitors are classified on that basis, according to whether they are sensitive or relatively insensitive to temperature variations. In some applications, such as coupling and bypass (described below), large capacitance is relatively more important than temperature variation. In others, such as timing, differentiating, integrating, and filtering, stability of capacitance is relatively more important than actual value, because the important quantity is the product of a capacitance and a resistance, and the latter can be precise. To complicate matters further, capacitance can vary not only with temperature, but also with any applied dc bias voltage and with the frequency of an applied sinusoidal voltage. We discuss some of these details in a subsequent chapter. Here, we note only that some manufacturers provide fairly complete Pspice models for some of their offerings that take such variations into account.
8.9 Energy Storage and Power Dissipation in a Capacitor The capacitor of Fig. 8.1 will remain charged when disconnected from the battery. That is, a nonzero voltage will exist across the terminals of the capacitor, which means that energy is stored in the electric field between the plates. If a charged capacitor is connected to a resistance, for example, current will pass through the resistor as the capacitor discharges and work will be done according to Joule’s law. If the capacitor is allowed to discharge completely, the work done will equal the energy stored in the field. Ability to store
p ¼ vi ¼ Cv
dv dw ¼ ; dt dt
(8.44)
where v(t) is the instantaneous voltage across the capacitor and wðtÞ is the instantaneous energy stored in the electric field produced by the voltage. Equation (8.44) implies that dw ¼ Cv dv ) wðtÞ ¼ C
ð vðtÞ
v0 dv0
vð1Þ
i 1 h ¼ C vðtÞ2 v2 ð1Þ : 2
We assume the voltage equals zero for t ! 1 (that the capacitor is initially uncharged). Thus the instantaneous energy stored in the electric field produced by a capacitor is given by wðtÞ ¼
1 C v2 ðtÞ; 2
(8.45)
where v(t) is the instantaneous voltage across the capacitor. For economy, the instantaneous energy stored in the electric field produced by a capacitor usually is referred to as the energy stored by (or in) the capacitor. The energy stored in the electric field produced by a voltage makes the voltage resistant to change, because it takes time to transfer energy to or from the electric field. In other words, the electric field created by a voltage gives the voltage a kind of inertia that resists changes in the voltage. A capacitor enhances this effect by concentrating and intensifying the electric field produced by a voltage across the capacitor. Example 8.16. Continuing Example 8.4, the energy stored in the capacitor at any time t is given by 1 1 w ¼ Cv2 ¼ CV 2 cos2 ð2pf tÞ 2 2 2 CV ¼ ½1 þ cosð4pf tÞ 4 ¼ 2:5 106 ½1 þ cosð4pf tÞ J:
8.9 Energy Storage and Power Dissipation in a Capacitor
Exercise 8.15. Refer to Fig. 8.8 and Exercise 8.2. Draw a graph of the energy stored in the electric field produced by the capacitor.
Exercise 8.16. A capacitor having capacitance C ¼ 250 pF is initially charged such that the terminal voltage is V0. The capacitor is then connected (at t ¼ 0) across a resistor having resistance R ¼ 10 kO. At what time is the energy stored in the capacitor equal to half of its initial value? The following fact is often useful: When a capacitor is fully charged by a constant source through a fixed resistance, the total energy delivered by the source is exactly twice the final energy stored by the capacitor. We can show this as follows. In Fig. 8.32, the switch is in position a for t < 0 and is moved to position b at t ¼ 0. The capacitor charges to vC ð1Þ ¼ V0 , at which point the energy stored on the capacitor is given by 1 wC ¼ CV02 : 2 The charge stored by the capacitor is given by Q ¼ CV0 . This charge must pass through the source, so the work done by the source on this charge (the energy delivered by the source) is given by wS ¼ QV0 ¼ CV0 ; 2
which is exactly twice the energy stored by the capacitor. Half of the energy delivered by the source is dissipated in the resistor, independent of the
i + V0
–
261
resistance of the resistor. We make use of this result in Section 8.10.9. The average power dissipated in an ideal capacitor equals zero, provided the applied current or voltage is bounded (as it always is in a physical circuit). We can show this as follows: The average power PT dissipated in a capacitor over an interval t0 t < t0 þ T is the change in stored energy divided by the duration of the interval, given by PT ¼
C 2 v ð t0 þ T Þ v 2 ð t0 Þ : 2T
In any physical problem, voltages are finite, so the quantity in the brackets is finite and P ¼ lim PT ¼ 0: T!1
+ a
C
vC –
Fig. 8.32 Pertaining to energy dissipation and storage in an RC series circuit (see text)
(8.47)
The average power dissipated in a capacitor over a finite time interval, given by (8.46) is not necessarily zero. The instantaneous power dissipated in a capacitor is not zero, nor is the peak power. A capacitor can absorb energy at some times and return energy to a circuit at other times. None of the energy absorbed (by an ideal capacitor) is lost to the circuit, but can be returned on demand. This is in contrast to a resistor, which converts electrical energy to heat energy that is then lost forever to the circuit. On an instantaneous basis, a capacitor behaves sometimes like a sink and other times like a source, but on average (over a sufficiently long time), is neither. Example 8.17. Find the average powers dissipated in the resistor and the source in the circuit shown in Fig. 8.33, where R ¼ 2 kO and vðtÞ ¼ V0 cosð2 p f tÞ; V0 ¼ 15 V: Solution: The average power dissipated in the resistor is
R
b
(8.46)
PR ¼
V02 225V2 ¼ ¼ 56:3 mW: 2R 4000
Because power is conserved and because the average power dissipated in a capacitor
262
8 Capacitance
v
+ –
vS
+ –
C
R
Fig. 8.33 See Example 8.17
+ R
C
vC (t)
Fig. 8.34 See Exercise 8.17
–
equals zero, the power dissipated in the source is Pv ¼ PR ¼ 56:3 mW:
Exercise 8.17. In Fig. 8.34, R ¼ 10 kO and C ¼ 250 nF. The instantaneous power dissipated in the resistor is given by pR ðtÞ ¼ p0 þ p1 cos2 ð2o0 tÞ, with p0 ¼ 20 mW, p1 ¼ 50 mW, and f0 ¼ 20 kHz. The dc component of the source voltage vS is positive and the source voltage is maximum at t ¼ 0. Obtain an expression for the instantaneous voltage vC(t) across the capacitor. Hint: Superposition of power is applicable (Why?). The discussion in this section pertains to an ideal capacitor. Real capacitors exhibit leakage resistance and what is called equivalent series resistance (ESR), so the average power dissipated by a real capacitor is not zero. Section 8.6 above describes leakage resistance. We describe ESR in a subsequent chapter.
• To produce a current or voltage proportional to the derivative or integral of another current or voltage (see Sections 8.10.1 and 8.10.2, below); • To store energy or charge for later release; e.g., as in the electronic flash unit on a camera and in switched-capacitor resistors (see Section 8.10.8, below); • As a timing device; e.g., where some action is triggered when voltage across a capacitor reaches a certain threshold, as in pulse-detection circuits, timing circuits, and some oscillators (not treated in this book); • To change the phase of one sinusoid relative to that of another, as in power-factor correction, some oscillators, and the starting and run capacitors on electric motors. (Power-factor correction is treated in a subsequent chapter); • As components of circuit models for physical devices; e.g., parasitic (junction) capacitance in a transistor and parasitic (residual) capacitance in a resistor or an inductor. (Discussed briefly in a subsequent chapter). At this point in our development, we are unprepared to illustrate all of the applications listed above or even to treat any particular one in great detail. This section describes a few applications and effects of capacitance at an introductory level. Additional applications and more detailed treatments are given in subsequent chapters, where we introduce useful circuits in which capacitance is essential or unavoidable.
8.10.1 Differentiating Circuits Applying Kirchhoff’s current law to the circuit shown in Fig. 8.35 gives C
dvin vout dvin ¼ 0 ) vout ¼ R C : dt R dt
(8.48)
8.10 Applications Capacitors are used in basically six ways: • To discriminate between sinusoids based on frequency (including dc), as in bypass, coupling, and filtering applications (e.g., Sections 8.10.3 and 8.10.6, below);
The output is proportional to the derivative with respect to time. The circuit is called a differentiator. The circuit shown works reasonably well for slowly varying inputs. Practical differentiators have additional components, the purposes of which are discussed in subsequent chapters.
8.10 Applications
263 R
vin (V)
C
vin
–
vout
5
+
t (ms)
0
Fig. 8.35 Differentiating circuit
0 1 2 3 4 5
Fig. 8.36 See Example 8.19
Example 8.18. In Fig. 8.35, let
vout (V )
vin ðtÞ ¼ V0 cos ð2 p f tÞ: The (ideal) output is vout ¼ R C
dvin ¼ 2 p f R C V0 sin ð2 p f tÞ: dt
5 0
0
1
2
3
4
5
t (ms)
–10
Fig. 8.37 See Example 8.19
Exercise 8.18. In Fig. 8.35, R ¼ 10 kO; C ¼ 22 pF, and the supply voltage for the op amp (assumed to be rail-to-rail) is VCC ¼ 15 V. The input vin is given by vin ¼ V0 cosð2pf tÞ: (a) If V0 ¼ 1 V, what is the highest frequency for which the circuit operates linearly? (b) If f ¼ 1 MHz, what is the largest value of V0 for which the circuit operates linearly?
For the values given, RC ¼ 2 103 s. For 0 t < 1 ms, the derivative (slope) is ð5 VÞ=ð1 msÞ ¼ 5; 000 Vs1 . For 3 ms t < 5 ms, the derivative (slope) is ð5VÞ=ð2msÞ ¼ 2;500Vs1 . For all other times, the slope equals zero. Thus 8 3 > <ð210 Þð5;000Þ¼10V; 0t<1ms; vout ¼ ð2103 Þð2;500Þ¼5V; 3mst<5ms; > : 0; all other times: Figure 8.37 shows a graph of the output.
Example 8.19. In Fig. 8.35, R ¼ 200 kO; C ¼ 10 nF, and the input vin is as shown in Fig. 8.36. Draw a graph of the output.
8.10.2 Integrating Circuits
Solution: The output is given by dvin ðtÞ dt ¼ RC ½instantaneous slope of vin ðtÞ:
vout ðtÞ ¼ RC
Under certain conditions, the circuit shown in Fig. 8.38 can produce an output proportional to the integral of the input, in which case the circuit is called an integrator. Because vn ¼ 0, the input current is given by i ¼ vin =R. This is also the current through the capacitor, because the current entering the n
264
8 Capacitance i
vin
R
i
vn
vin
V0 C
vout
–
t
0
+
vout Fig. 8.38 Integrating circuit
terminal of the op amp equals zero. Thus the voltage across the capacitor (the output voltage) is given by ð 1 t vout ¼ iðt0 Þ dt0 C 1 ð 1 t ¼ vin ðt0 Þ dt0 : (8.49) RC 1 In practical op-amp circuits, there must be feedback at dc. If the capacitor in Fig. 8.38 is ideal, there is no such feedback. Physical capacitors exhibit leakage resistance, and in some applications, leakage resistance provides sufficient dc feedback. For present purposes, we assume that is the case. Exercise 8.19. In Fig. 8.38, let vin ðtÞ ¼
Fig. 8.39 See Example 8.20
Example 8.20. In Fig. 8.38, let vin ¼
Obtain an expression for the output vout ðtÞ. Solution: From (8.49)
vout
0; t 0; V0 cosð2 p f tÞ; t > 0:
Obtain an expression for the output vout :
0; t 0; V0 ; t > 0:
ð 8 1 t > > 0 dt0 ¼ 0; t 0; < RC 1 ¼ ðt > V0 t > : 1 V0 dt0 ¼ ; t > 0: RC 0 RC
Figure 8.39 shows a graph of the output. What limits the output?
Example 8.21. In Fig. 8.38, R ¼ 200 kO; C ¼ 10 nF, and the input vin is as shown in Fig. 8.40. Draw a graph of the output. Solution: The output is given by 1 vout ðtÞ ¼ RC
" # instantaneous net area bounded by 1 : vin ðt Þdt ¼ RC vin ðt0 Þ and the t0 axis to the left of t0 ¼ t 1
ðt
0
0
A graph of vin ðt0 Þ versus the variable of integration t0 is obtained by simply re-labeling the axes in Fig. 8.40. To perform the integration, imagine the time t (the upper limit of integration) advancing from left to right on the t0 axis. For each value of t, compute the area bounded by vðt0 Þ and the t0 axis to the left of t. For t < 0, vin ðt0 Þ ¼ 0 and the area bounded by vin ðt0 Þ to the left of t equals zero. For 0 t < 1 ms, the area bounded by vin ðt0 Þ to the left of t equals ð10 VÞ t.
8.10 Applications
265
For 1 ms t < 3 ms, the area bounded by vin ðt0 Þ to the left of t equals ð10 VÞ ð1 msÞ ¼ 103 V s. For 3 ms t < 5 ms, the area bounded by vin ðt0 Þ to the left of t equals 103 V s þ ð5 VÞ ðt 3 msÞ. For t > 5 ms, the area bounded by vin ðt0 Þ to the left of t is constant and equal to 103 V s þ ð5 VÞ ð5 ms 3 msÞ ¼ 0. Thus 8 0; t < 0; > > > > ð10 VÞt; 0 t < 1 ms; < 1 1 ms t < 3 ms; vout ¼ 103 V s; > RC > 3 10 V s þ ð 5 V Þ ð t 3 ms Þ; 3 ms t < 5 ms; > > : 0; t 5 ms where RC ¼ 2 ms. Figure 8.41 shows a graph of the output. In Example 8.20, the magnitude of the output increases linearly with time, and will drive the op amp to saturation, at which point the circuit no longer acts as an integrator. Exercise 8.19 seems to illustrate that the circuit in Fig. 8.38 can function as an integrator for a long time if the input contains no dc component. However, in any real such circuit, a small but nonzero dc offset at the input is almost unavoidable, and will eventually drive the output to saturation, because there is no (or very little) feedback at dc (an
ideal capacitor is an open circuit at dc). Practical integrators provide a means of resetting the output to zero after a predetermined time to avoid saturation. Figure 8.42 shows such a circuit, in which the switch is closed periodically to discharge the capacitor and reset the output to zero (the switch usually is electronic, not mechanical). The circuit in Fig. 8.42 is called a finitetime integrator, because the integration ends when the switch is closed. Finite-time integrators are used in a number of applications, including analog computers and various pulse-detection circuits.
vin (V)
5 0
1
0
2
3
5
4
t (ms)
−10
Exercise 8.20. In Fig. 8.42, R1 ¼ 2 kO, C ¼ 10 pF, and R2 ¼ 100 O. The circuit must be able to integrate a constant 5 mV input for 100 ms (before the op amp saturates). (a) What is the required power supply voltage? (b) When the integrator is reset (when the switch is closed), how long does it take for the capacitor to discharge, before another integration can begin? (Give and justify a reasonable time).
Fig. 8.40 See Example 8.20
vout (V) 5
R2
vin 0 0
R1
– +
C
t (ms) 1
2
3
Fig. 8.41 See Example 8.20
4
5
Fig. 8.42 A finite-time (resettable) integrator
vout
266
8 Capacitance
8.10.3 Bypass Capacitors
i (t) i(t) = Idc + iac (t)
The purpose of a bypass capacitor is to shunt undesirable time-varying components of a current, called ripple, around a resistive load, while desirable dc components pass through the load, such that the load voltage is nearly constant. There are at least three major areas of application: • Currents demanded by various components in linear systems fluctuate with varying demand. For example, in an audio amplifier, current delivered to the loudspeaker fluctuates with loudness, so the current demanded of the amplifier’s output stage varies with the instantaneous loudness of the audio output. Such varying demand causes the current drawn from the supply to fluctuate, and the fluctuations can be coupled to signal lines; e.g., through stray capacitance or by causing the power supplied to earlier stages to fluctuate. Bypass capacitors can reduce such fluctuations. Plastic-dielectric capacitors are often used in such applications, but if high precision is required, silver-mica capacitors might be used. • In power supplies, relatively large bypass capacitors (often, 1000 mF or more) are used to smooth the ripples in a rectified sinusoidal voltage. The capacitors most commonly used in larger power supplies are aluminum electrolytics because of the large capacitances achievable with such capacitors. Tantalum electrolytics might be used in smaller (low-voltage) power supplies. Electrolytic capacitors are typically imprecise. For example, the tolerance on an aluminum electrolytic might be þ60%/ 40%. Conservative sizing is necessary where such capacitors are used. • In digital systems, bypass capacitors are attached from the power pin to ground at virtually every integrated circuit (IC) to keep the supply voltage at the pin within the operating range for the IC. Typical values range from about 10 to 100 nF, and occasionally to 500 nF. Ceramic capacitors are often used in this application, partly because of their large capacitance to volume ratios. In this subsection, we describe bypassing in applications where the ripple can be approximated by a sinusoid. In the next, we describe bypassing for rectifier circuits, and in the next after that, bypassing for digital systems. We do not treat bypassing for very
iL (t) R
R
≅ iac (t) C
+
vL (t) = Vdc + vac (t) –
(a)
(b)
Fig. 8.43 Illustrating the function of a bypass capacitor
high-frequency applications because a useful treatment of that topic would take us too far afield. Refer to Fig. 8.43(a). Let iðtÞ ¼ Idc þ iac ðtÞ denote the current through a resistive load R, where the dc component Idc is the desirable component and the ac component iac ðtÞ is undesirable. In such cases, an appropriate figure of merit is the ripple factor, defined as g¼
Iac rms Iac rms R Vac rms ¼ ¼ : jIdc j jIdc jR jVdc j
(8.50)
To reduce the ripple in the load, we may connect a bypass capacitor in parallel with the load, as shown in Fig. 8.43(b). The purpose of the bypass capacitor is to shunt most of the ac component iac ðtÞ, such that the load current iL ðtÞ is largely the dc component Idc . A simplified approach to specifying a bypass capacitor is as follows. We assume the ripple is approximately sinusoidal. Thus let iac ðtÞ ffi Iac cosðo0 tÞ: If the capacitor is absent, all of the current passes through the resistor, and the ripple factor is given by g0 ¼
Iac rms jIac j ¼ pffiffiffi : jIdc j 2jIdc j
(8.51)
With the capacitor in place, all of the dc current passes through the resistor (a capacitor does not pass dc), so the dc component of the load voltage is given by Vdc ¼ Idc R: Ideally, almost all of the ripple current is diverted through the capacitor. In that case, the load voltage is given approximately by
8.10 Applications
267
ð 1 t iac ðt0 Þdt0 C 0 Iac sinðo0 tÞ: ¼ v L ð 0Þ þ o0 C
vL ðtÞ ffi vL ð0Þ þ
capacitor. (b) Find the capacitance that reduces the ripple factor to 0.1% (0.001). Solution: (a) From (8.51),
Thus the ac component of the load voltage is given by vac ðtÞ ¼
Iac sinðo0 tÞ o0 C
Iac 5 g0 ¼ pffiffiffi ¼ pffiffiffi ¼ 70:7 103 : 50 2 Idc 2 From (8.53)
and the ripple factor is given (approximately) by g¼
Vac rms jI j g0 pac ffiffiffi ffi ¼ : jVdc j o0 C 2jIdc jR o0 RC
(8.52)
1 g0 1 70:7 103 Cffi ffi o0 R g o0 R 1:00 103 ffi
70:7 ffi 563 mF: ð2p 104 HzÞð2 OÞ
Thus the bypass capacitance required to achieve a specified (small) ripple factor g in a resistive load R is given by 1 g0 1 g0 Cffi ¼ ; o0 R g 2pf0 R g
(8.53)
where g0 is the ripple factor in absence of bypassing and f0 is the frequency of a sinusoidal approximation to the ripple. A somewhat more careful analysis yields (compare with (8.52)) g¼
Vac rms g0 ; D ¼ o0 RC ¼ pffiffiffiffiffiffiffiffiffiffiffiffiffiffi jVdc j 1 þ D2
(8.54)
Exercise 8.21. Refer to Example 8.22. Calculate the required capacitance using (18.55). If a bypass capacitor is effective for a sinusoidal current having frequency f0 it is even more effective for sinusoids having frequencies greater than f0.
Exercise 8.22. About 99% of any sinusoidal current having frequency greater than 100 Hz is to be diverted (bypassed) around a 1 kO resistive load by a capacitor in parallel with the load. What capacitance is required?
and (compare with (8.53)) s ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ffi 1 g0 2 Cffi 1: g o0 R
(8.55)
The difference between (8.53) and (8.55) is less than 1% if g0 > 7g, as is true in virtually all bypassing applications.
Equation (8.53) is not strictly applicable if the ripple is not sinusoidal. Nonetheless, we often may use that relation if the ripple is approximately periodic and if we can estimate the period T of the ripple. In such cases, it is advisable to incorporate a margin of 25% or so; i.e., Cffi
Example 8.22. In Fig. 8.43, Idc ¼ 5 0 mA, Iac ¼ 5 mA, f0 ¼ 10 kHz, and R ¼ 2 O. (a) Find the ripple factor in absence of the
1:25 g0 T : g 2p R
(8.56)
For example, if the period of the ripple is about 1 ns, the equivalent load is about 1O, and we require g0 =g ¼ 100, the required capacitance is about 20 nF.
268
8 Capacitance
8.10.4 Bypass Capacitors (Filter Capacitors) in Rectifier Circuits
RS
+ + –
Equations (8.52) and (8.54) are strictly applicable only to linear circuits in which the load is resistive and the ripple is sinusoidal. They might be approximately correct if the circuit is approximately linear, the load is predominately resistive, and the ripple is approximately sinusoidal, but such applications must be considered on a case-by-case basis. An application in which the relations above are generally inapplicable is in power supplies where bypass capacitors (called filter capacitors) are used to suppress the ripple introduced by rectifier circuits. In such applications, the circuit is decidedly nonlinear and the ripple is decidedly non-sinusoidal. Figure 8.44 shows a half-wave rectifier circuit driving a resistive load RL . Figures 8.45 and 8.46 show results of an analysis of the circuit.15 Figure 8.45 shows the load voltages for C ¼ 100 mF and C ¼ 1; 000 mF. The peak-to-peak load voltage ripple is approximately 102 V for C ¼ 100 mF and approximately 13.4 V for C ¼ 1; 000 mF. The rms ripple is approximately 37.6 V for C ¼ 100 mF and approximately 4.92 V for C ¼ 1; 000 mF. The dc load voltage is approximately 93.8 V for C ¼ 100 mF and approximately 108 V for C ¼ 1; 000 mF.16 The measured (calculated) ripple factors are g100 mF g1000 mF
37:6 V ffi ffi 0:401; 93:8 V 4:92 V ffi 0:046: ffi 108 V
iD
vS
C
RL
vL –
vS = VS sin (w 0t), VS = 170 V, f0 = 60 Hz RS = 10 Ω, RL = 100 Ω Fig. 8.44 Bypass (filter) capacitor in a half-wave rectifier circuit
180 160 140 120 VL dc
100 80 60 40 20 0
0
4
8
12
16
20 24 t (ms)
28
32
36
40
28
32
36
40
(a) C = 100 μF vS
vL 180 160 140 VL dc
120 100 80 60 40 20
Increasing the capacitance by an order of magnitude decreases the ripple by almost an order of magnitude. A price of increasing the filter capacitance is an increase in the diode current, which determines the
15
The equations describing the circuit are nonlinear and cannot be solved in closed form. The analysis was performed numerically, using methods described in John R. Hauser, Numerical Methods for Nonlinear Engineering Models, Springer, 2009. 16 All these values were obtained from the numerical analysis.
0
0
4
8
vL
12
16
20 24 t (ms)
(b) C = 1000 μF vS
Fig. 8.45 Load-voltage waveforms in a half-wave rectifier circuit for two values of the filter capacitance
size and cost of the diode. Figure 8.46 shows the initial current in the diode for two values of the filter (bypass) capacitor C. The maximum diode current is approximately 5 A for C ¼ 100 mF and 13.5 A for C ¼ 1; 000 mF. These currents would be even larger
8.10 Applications
269
14
Vmax – Vmin
vL(V)
12
vˆL(V)
10 8 iD (A) 6 4 2
t
0 tp
0 0
0
2
4
6
C = 100 μF
8 10 12 14 16 18 20 22 24 26 28 30 t (ms) C = 1000 μF
Fig. 8.46 Diode current in a half-wave rectifier circuit for two values of the filter capacitance
if the circuit were energized on a peak of the source voltage. We can obtain approximate expressions for the rms ripple and ripple factor, as follows: When the diode in Fig. 8.45 is conducting, it is approximately a short circuit (because the diode drop is much smaller than the source voltage), and the parameters of the The´venin equivalent for the circuit seen by the capacitor are vT ¼
RL vS ; RT ¼ RS kRL : RL þ RS
When the diode is not conducting, it is approximately an open circuit, and the capacitor discharges through the load resistor RL . Thus the charging and discharging time constants are different, and are given by Charging : tS ¼ ðRS k RL ÞC; Discharging :tL ¼ RL C: In this example and often in applications, RS RL , and the charging time constant is much smaller than the discharge time constant. Thus the load voltage almost follows the source voltage during charging, but not during discharge. If the discharge time constant is much larger than the period of the source voltage, as is usually the case, the discharge will occupy the lion’s share of each period, and we may estimate the peak-to-peak ripple as VRPP ¼ Vmax Vmin ;
(8.57)
T
Fig. 8.47 Piecewise-linear (triangular) approximation to the load voltage in a half-wave rectifier circuit
where Vmin
T ; ffi Vmax exp tL
(8.58)
and thus
T Vmax Vmin ffi Vmax 1 exp : tL
(8.59)
The dotted line in Fig. 8.47 shows one period of the ripple, translated to the origin. In the figure, Vmax and Vmin denote the maximum and minimum values of the load voltage, T is the period of the ripple, and tp is the time at which the peak of the ripple occurs. The solid line in Fig. 8.47 represents a piecewiselinear (triangular-wave) approximation to the ripple. For tp t < T (approximately), the ripple follows an exponential decay, with time constant tL ¼ RL C, as given above. For tL T, the exponential decay is approximately linear during tp t < T. It can be shown that the rms amplitude of the ripple, based upon the triangular-wave approximation, is given by VL ac rms ¼
Vmax Vmin pffiffiffiffiffi : 12
(8.60)
If the ripple is small, as is usual, then Vmax ffi VDC , where VDC is the dc component of the load voltage. With this approximation, (8.60) and (8.59) give
Vmax Vmin Vmax T pffiffiffiffiffi VL ac rms ¼ ¼ pffiffiffiffiffi 1 exp tL 12 12
VDC T ffi pffiffiffiffiffi 1 exp ; t 12 L
270
8 Capacitance
and the ripple factor is given by
VL ac rms 1 T ; ffi pffiffiffiffiffi 1 exp g¼ VDC tL 12 tL ¼ RL C:
(8.61)
To achieve a small ripple, we want the discharge time constant tL to be large relative to the period T of the ripple, such that the load voltage does not change much during the discharge part of each cycle. If that is the case, the factor in the brackets in (8.61) is approximately T=tL and the ripple factor is approximately g¼
VL ac rms T T pffiffiffiffiffi : ffi pffiffiffiffiffi ¼ VDC tL 12 RL C 12
(8.62)
For the circuit in Fig. 8.44, the ripple factors calculated using (8.62) are 0.481 for C ¼ 100 mF and 0.048 for C ¼ 1; 000 mF, compared to 0.401 and 0.046 obtained by a numerical analysis of the circuit. From (8.62), the capacitance C required to achieve a specified small ripple factor g is given by C¼
T pffiffiffiffiffi : RL g 12
(8.63)
From (8.63), achieving a ripple factor of 0.046 in the circuit of Fig. 8.44 requires a capacitance of 1; 046 mF, which is close to the 1; 000 mF used to achieve that ripple factor. The approximate relation (8.63) improves as the required ripple factor decreases, and is a useful design relation for half-wave rectifier circuits. But keep in mind that increasing the filter capacitance increases the diode current and the required power-dissipation rating for the diode. Note that T is the period of the rectified voltage, which equals the period of the source for half-wave rectification and equals half the period of the source for full-wave rectification. Keep in mind that several approximations were invoked in deriving (8.63). One assumed the ripple is triangular. Another assumed that the maximum amplitude of the load voltage is approximately equal to the dc component of the load voltage. This approximation is poor unless the rms ripple is no more than a few percent of the dc component. Nonetheless, using a filter capacitor prescribed by (8.63) achieves a slightly smaller ripple than the specified
value ðgÞ. A capacitance calculated using (8.63) can be quite large for low-frequency applications. For example, for a 60 Hz source and 100 O load, the capacitance required to achieve a 1% ripple factor exceeds 4; 000 mF. Thus other components usually supplement the smoothing provided by filter capacitors in such applications.
8.10.5 Bypassing in Digital Systems An important application of bypass capacitors is in smoothing power-supply voltages at the power-input terminals of each integrated circuit (IC) in a larger digital system, such as a computer or memory bank. Each IC can contain a great many individual switching circuits (components of logic gates). Whenever a logic gate changes state, it must charge or discharge stray and parasitic capacitances, and draws a current pulse (þ or –) from the supply to do so. Thus, as various circuits in the IC switch from one state to another, the current drawn by the IC from the power supply varies, and wiring and source resistance can cause the supply voltage to vary at the IC. The variation can be increased by operation of other IC’s drawing from the same supply. If the variation exceeds a certain tolerance, the circuit can malfunction. The job of a bypass capacitor is to keep the power-supply voltage at the IC within the range acceptable to the IC. Supply-voltage fluctuations at an IC are decidedly non-periodic, and specifying a bypass capacitor for a digital integrated circuit is done differently from specifying bypass capacitors for linear and rectifier circuits, as described below. On average, the voltage across a bypass capacitor equals the supply voltage. The capacitor reduces ripple by momentarily supplying current when the voltage tries to fall and momentarily sinking current (absorbing charge) when the voltage tries to rise. The bypass capacitor’s terminal characteristic i¼C
dv dt
governs the relation between current and voltage change. Using the approximation dv=dt ffi Dv=Dt and solving for the capacitance gives C¼i
Dt ; Dv
(8.64)
8.10 Applications
271 6
v1 (V) 5 4 6
v2 (V) 5
Fig. 8.48 Supply voltage at the terminals of an IC with and without bypass
4
0
10
20
30
which we interpret as follows: The current i is the current sourced or sunk by the capacitor in order to limit the change in voltage to Dv during an interval Dt. We may use (8.64) to estimate the bypass capacitance needed by a digital circuit, as illustrated by the next example. Example 8.23. A certain digital integrated circuit (IC) is operating at a clock frequency of 1 GHz. As it operates, it can require a current of 50 mA above or below that provided (on average) by the supply. It is required that the supply voltage at the IC be kept within Dv ¼ 5 mV of the specified value. Specify a bypass capacitor. Solution: From (8.64) C ¼ ð50 mAÞ
1 ns 5 mV
¼ 10 nF:
In most applications (in digital systems), bypass capacitances fall in the range from about 10 to 500 nF. Such capacitors can be quite small, because the operating voltages are small (typically, 5 V or less). Figure 8.48 illustrates the smoothing effect of a bypass capacitor. The upper trace is the voltage at the power pin of an un-bypassed integrated logic circuit in a larger logic system. The fluctuations due to switching in this and other circuits in the larger system are evident. The lower trace shows the voltage at the same pin after adding a bypass capacitor. While not perfectly smooth, the bypassed voltage is well within specifications on the IC. Usually, one would add a little (10–25%) to the capacitance given by (8.64) to account for the occasional larger-than-expected current demand. On the theory that bigger is better, you might be tempted to choose a capacitance much larger than that. But that is not always wise. Parasitic effects (e.g., lead
40
50
60
70 t (ns)
80
90
100
110
120
130
inductance and losses in the dielectric) and size (space occupied) increase with capacitance, as does the current required to charge or discharge the capacitor, so a larger-than-necessary capacitor can cause as many problems as it solves.
8.10.6 Coupling Capacitors Figure 8.49 shows a source connected to a resistive load through a coupling capacitor C. The source and load are said to be capacitively coupled.17 The usual purpose of capacitive coupling is to prevent a dc component of the source voltage from reaching the load while allowing ac components above a certain frequency to pass through to the load. Below, we describe how to specify a coupling capacitor. We assume the source voltage is of the form vS ðtÞ ¼ Vdc þ vac ðtÞ; where vac ðtÞ has no dc component. The circuit is linear, so superposition is applicable. The capacitor will block the dc component Vdc by maintaining an average charge Vdc , so the load voltage has no dc component. We need concern ourselves with only the ac component. We assume a sinusoidal model vac ðtÞ ¼ Vac cosðo0 tÞ;
(8.65)
which could be the lowest-frequency component of a sum of such voltages. The circuit is linear, so the voltage across the capacitor is also sinusoidal, of the form vC ðtÞ ¼ VC cosðo0 t þ yÞ:
17
(8.66)
Direct coupling also is called dc coupling and capacitive coupling also is called ac coupling.
272
8 Capacitance +
If we specify that
vC – +
+ –
vS
C
vR
i
– load
source
jVR j ¼ kj Vac j; 0 < k < 1;
R
meaning that the rms ac load voltage is a specified fraction k of the rms ac source voltage, then
Fig. 8.49 Capacitive coupling of a source to a load
" Vac ¼ k Vac 2
From (8.12), the current through the capacitor is given by i¼C
dvC ¼ o0 CVC sinðo0 t þ yÞ: dt
VR : o0 RC
2 #
1 1þ o0 RC
k ) o0 RC ¼ pffiffiffiffiffiffiffiffiffiffiffiffiffi : 1 k2
C
(8.67)
where VR ¼ o0 RCVC ) VC ¼
2
Therefore the coupling capacitance required to ensure that the rms ac load voltage equals at least a fraction k of the rms ac source voltage is given by
It follows that the load voltage is given by vR ðtÞ ¼ iðtÞR ¼ o0 RCVC sinðo0 t þ yÞ ¼ VR sinðo0 t þ yÞ;
2
(8.68)
We wish to express the rms load voltage as a fraction of the rms ac source voltage. Applying Kirchhoff’s voltage law to the circuit gives vac ðtÞ ¼ vR ðtÞ þ vC ðtÞ ) Vac cosðo0 tÞ ¼ VR sinðo0 t þ yÞ þ VC cosðo0 t þ yÞ; From trigonometry, pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a cosðaÞ þ b sinðaÞ a2 þ b2 cosða ’Þ; b : ’ ¼ tan1 a
k pffiffiffiffiffiffiffiffiffiffiffiffiffi : o0 R 1 k2
(8.69)
The analysis leading to (8.69) ignores the source resistance (not shown in Fig. 8.49). This is equivalent to assuming that the load resistance is much larger than the source resistance, which is true in the majority of applications where capacitive coupling is employed. A much more tedious analysis that does not ignore the source resistance leads to C
k 1 pffiffiffiffiffiffiffiffiffiffiffiffiffi sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ffi : 2 2pf0 RL 1 k2 k RS RS 1 2þ 1 k 2 RL RL (8.70)
In applying either (8.69) or (8.70), keep in mind that tolerances on capacitors can be large – 20% or more, and consider incorporating a margin of 25% or so; e.g., by requiring
Thus Vac
qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi cosðo0 tÞ ¼ VR 2 þ VC 2 cosðo0 t þ y ’Þ;
C
1:25k pffiffiffiffiffiffiffiffiffiffiffiffiffi : o0 R 1 k 2
so the rms amplitudes are related as pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi VR 2 þ VC 2 pffiffiffi ) Vac 2 ¼ VR 2 þ VC 2 2 2 VR ¼ VR 2 þ : o0 RC
jVac j pffiffiffi ¼ 2
Example 8.24. The first stage of a two-stage amplifier is capacitively coupled to the second stage, as shown in Fig. 8.50. The output resistance of the first stage (the source resistance) is negligible. The input resistance of the second
8.10 Applications
273
The simulation shown in Fig. 8.51 below illustrates this result. (The voltmeters indicate rms amplitude.) The voltage gain of each inverting amplifier equals 25, the coupling capacitance is that calculated above, and the overall voltage gain at 30 Hz (to three significant figures) is
stage is 20 kO. The voltage gain of each amplifier is 25. The overall voltage gain must be at least 500 for any sinusoid whose frequency exceeds 30 Hz. Specify the coupling capacitor. Solution: If the amplifiers were direct coupled, the overall voltage gain would be ð25Þ2 ¼ 625. The specified gain at 30 Hz is 500, so k¼
Av ¼
500 ¼ 0:8 625
as specified.
and we require C
5:00 V ¼ 500; 10:0 mV
k pffiffiffiffiffiffiffiffiffiffiffiffi 2pf0 R 1 k2
)C
Exercise 8.23. The two stages of an amplifier are coupled as shown in Fig. 8.50, where C ¼ 500 nF. The output resistance of the first stage is negligible and the input resistance of the second stage is 10 kO. For what frequencies of a sinusoidal output from the first stage is the overall gain reduced by a factor of 0.5 or more?
0:8 2pð30HzÞð20 103 OÞð0:6Þ
) C 354nF:
1st stage
C
2nd stage
Effects of capacitive coupling in cascaded stages are cumulative. For example, refer to Fig. 8.52, where o0 > 0. We may assume (without loss of generality)
Fig. 8.50 See Example 8.24
XMM1 XMM2
+ −
+ − R2
R4
500 kΩ
500 kΩ
R1 V1 + −
Fig. 8.51 See Example 8.24
20 kΩ
14.14 mV 30 Hz 0Deg
U1 −
C1
R3
+
354 nF
20 kΩ
OPAMP_3T_VIRTUAL
U2 − + OPAMP_3T_VIRTUAL
274
8 Capacitance
vS
C2
C1
RS + –
circuit 1
+
+
v1
v2
–
–
circuit 2
+
v4
–
v1 = V1 cos (w 0t + q1) v2 = V2 cos (w 0t + q2)
vS = VS cos (w0t) Fig. 8.52 Circuits in cascade, with capacitive coupling
+
v3
–
V3 = Av2V2
R2
R2
R1
C1
–
vS
+
RL
–
v3 = V3 cos (w 0t + q3) vL = VL cos (w 0t + qL) VL = Av3V4 v4 = V4 cos (w 0t + q4)
V1 = Av1VS
+ –
+
vL
circuit 3
v1
R1
v2
C2
– +
vL
RL
v3
Fig. 8.53 See Example 8.25
that the initial phase angles yn are such that V1, V2, VL are positive. We also assume that the output resistance of each circuit (or the source) is much smaller than the input resistance of the succeeding circuit (or the load). Suppose the coupling capacitors are specified such that V2 ¼ k1 V1 ; V4 ¼ k2 V3 for frequency f0. Then VL ¼ Av3 V4 ¼ Av3 k2 V3 ¼ Av3 k2 Av2 V2 ¼ Av3 k2 Av2 k1 V1 ¼ Av3 k2 Av2 k1 Av1 VS : The overall voltage gain is given by Av ¼
VL ¼ Av3 Av2 Av1 k1 k2 : VS
If we want the overall voltage gain to be a fraction k of the product of the individual gains, then we must specify the coupling capacitors such that k1 k2 ¼ k. If the input resistances of circuit 2 and circuit 3 are R2 and R3, respectively, and if the output resistances of circuit 1 and circuit 2 are negligible, then we would require C1
k1 k2 pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ; C2 pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi : 2 2pf0 R2 1 k1 2pf0 R3 1 k2 2 (8.71)
Example 8.25. Figure 8.53 shows a two-stage amplifier, where vS ¼ VS cosð2pf0 tÞ, with f0 ¼ 80 Hz and VS ¼ 5 mV. Assume the op amps are ideal. The source resistance and the output resistances of the individual amplifiers are negligible. (a) Assume the coupling capacitors are conductors and specify the resistances R1 ; R2 such that the overall voltage gain is Av ¼ 2; 500. (b) Specify the coupling capacitors such that the overall voltage gain for f f0 equals or exceeds 0:8Av ¼ 2; 000. Solution: (a) The overall voltage gain is given by Av ¼
2 VL rms R2 ¼ k1 k2 ; VS rms R1
k1 ¼
V2 rms VL rms ; k2 ¼ : V1 rms V3 rms
where
If the capacitors are conductors, then k1 ffi 1, k2 ffi 1, and 2 R2 ¼ ð50Þ2 ) R2 ¼ 50R1 : Av ¼ 2; 500 ffi R1
8.10 Applications
275
vS
We choose
C
V0
vS
R2 ¼ 1MO ) R1 ¼ 20 kO: (b) Let k1 ¼ k2 ¼ (8.71)
pffiffiffiffiffiffiffi 0:8 for f ¼ f0 . From
pffiffiffiffiffiffiffi 0:8 pffiffiffiffiffiffiffiffiffiffiffiffiffiffi ¼ 199 nF ffi 200 nF: C1 ¼ C2 ¼ 2pf0 R1 1 0:8
0
0
t0
+ –
t
T
Fig. 8.54 Rectangular pulse-train source capacitively coupled to a load (see also Fig. 8.55)
vL
V1
V1
vSac
Vmax
Equations (8.69) and (8.70) are applicable to a sinusoidal current or voltage, or to a sum of sinusoidal currents or voltages, where the lowest frequency represented equals f0. For piecewise-constant signals, we can approach the problem of specifying a coupling capacitor from another point of view. Refer to Fig. 8.54, where a rectangular pulse train source vS ðtÞ is capacitively coupled to a resistive load RL . The dc component of the pulse train is blocked by the capacitor, so the average value of the load voltage must be zero. Also, the voltage across the capacitor cannot change instantaneously, so when the source voltage changes by V0 , the load voltage must also change by V0 . The dc component of the source voltage vS is given by VS dc
1 ¼ T
ðT 0
V0 t0 vS ðtÞdt ¼ ; T
so the maximum and minimum amplitudes of the ac component of vS are given by t0 ; Vmin ¼ Vmax V0 : Vmax ¼ V0 1 T
(8.72)
Figure 8.55 shows a qualitative graph of the load voltage vL (exaggerated), superimposed on a graph (dotted) of the ac component of the source voltage. By inspection, t 0 V2 ¼ V1 exp ; t
(8.73)
where t ¼ RL C:
V2 0
vL
t0
0
T V1 – V0
Vmax – V0
t
V2 – V0
Fig. 8.55 Qualitative graph of the response of the circuit in Fig. 8.54
We know that V2 < Vmax < V1 :
(8.75)
Thus, a measure of the difference between the load voltage vL and the ac component of vS is given by h t i 0 V1 V2 ¼ V1 1 exp t t V1 V 2 0 ) ¼ 1 exp ; V1 t
(8.76)
where we have used (8.73). If the difference V1 V2 is sufficiently small, as is usually the case in problems of this kind, then V1 V2 is approximately twice the maximum error DV, and we may write t 2DV 0 ¼ 1 exp : t V1
(8.77)
Finally, if the error is sufficiently small, we may use V1 ffi Vmax in (8.77) to obtain t 2DV 0 ¼ 1 exp t Vmax )t¼
(8.74)
+ RL vL –
t0 : lnð1 2DV=Vmax Þ
(8.78)
276
8 Capacitance
Equation (8.78) gives the time constant required to achieve a specified error. The relation is applicable to circuits equivalent to the circuit in Fig. 8.54 and is valid if DV Vmax . For DV small, the relation tends to give a time constant slightly larger than necessary (an error smaller than specified). The parameter t0 is the duration of the positive pulse in each period of the input, VS max is the maximum amplitude of the ac component of the input, and DV is (approximately) the maximum difference between the load voltage and the ac component of the input. Example 8.26. In Fig. 8.54, V0 ¼ 10 V, T ¼ 10 ms, t0 ¼ 2 ms, and RL ¼ 5 kO. The load voltage vL must be within 100 mV of the ac component of the source voltage vS at all times. Specify the coupling capacitor C. Calculate the voltages V1 and V2 defined by Fig. 8.55 to verify your answer. Solution: The dc component of the source voltage is V0 t0 ¼ 2 V: T Thus, in (8.78) DV ¼ 100 mV. We find
Vmax ¼ 8 V
and
t0 2 ms ¼ lnð1 2DV=Vmax Þ lnð1 0:2=10Þ t 100 ms ffi 100ms ) C ¼ ¼ ¼ 20mF: RL 5kO
t¼
From Fig. 8.55, we have t 0 V2 ¼ V1 exp ; t T t0 : (8.79) V1 V0 ¼ ðV2 V0 Þ exp t Using the first relation to replace V2 in the second gives h i t T t0 0 V1 V0 ¼ V1 exp V0 exp t t T t0 1 exp t ffi 8:079V; ) V1 ¼ V 0 T exp 1 t
whence t 0 V2 ¼ V1 exp ¼ 7:919 V: t The errors are V1 Vmax ¼ 79 mV; Vmax V2 ¼ 81 mV: both of which are less than 100 mV.
Exercise 8.24. In practice, a non-negative rectangular pulse train usually is described in terms of its duty cycle d, period T, and peak amplitude V0, where the duty cycle is the fraction of each cycle for which the pulse train is positive. Express the requirement (8.78) for faithful transmission of the ac component of a rectangular pulse train in terms of the duty cycle of the pulse train.
8.10.7 Input Bias Current Compensation in Capacitively Coupled Amplifiers Recall from Chapter 7 that input bias currents in an op amp can cause a dc offset voltage at the output of an amplifier, and that the offset can be largely corrected by inserting a compensating resistor RX as shown in Fig. 8.56 for direct-coupled inverting and non-inverting amplifiers. The approximations assume R1 RS and R2 R1 , which often hold for such amplifiers. Input-bias-current compensation for capacitively coupled amplifiers is different from that for directcoupled amplifiers. The compensating resistor for a capacitively coupled inverting amplifier is connected from the positive input (p) terminal to ground, as shown in Fig. 8.57. But in this case, there is no dc path back through the source, so no dc bias current passes through R1. Requiring that the output vo due to the input bias currents alone equals zero requires vp ¼ vn , which, again assuming Ip ¼ In , implies In
Ri Ri ¼ Ip R X R2 2 ) RX ¼ R2 ; 2
(8.80)
8.10 Applications
277 R2 R1
RS
RS
–
RX + –
+ + –
Fig. 8.56 Input bias-current compensation in directcoupled inverting and noninverting amplifiers
vS
+ –
RX
R1
(a) inverting amplifier
RS + –
In n
R1
vS
Ip
–
p +
RX
RS + –
o
R2
(b) non-inverting amplifier RX = R1 R2 –RS ≅ R1
RX = (R1 + RS) R2 ≅ R1
R2 C
vS
vS
C
Ip RX R1
p
In
n
o
+ –
RL R2
RL
Fig. 8.58 Input bias current compensation for a capacitively coupled non-inverting amplifier, where RX ffi R1 Fig. 8.57 DC bias compensation for a capacitively coupled inverting amplifier, where RX ¼ R2
where Ri is the input resistance of the op amp. Thus, for a capacitively coupled inverting amplifier, the input bias current compensating resistance equals the feedback resistance R2, not the input resistance R1, as in direct-coupled amplifiers. In a capacitively coupled non-inverting amplifier, the compensating resistor must be connected from the p terminal to ground, as shown in Fig. 8.58, because there is no dc path back through the source. Requiring that the output vo due to the input bias currents alone equals zero requires vp ¼ vn , which (assuming Ip ¼ In ) leads to Ri Ri Ip RX R R ¼ I ð Þ k n 1 2 2 2 ) RX ¼ R1 k R2 ;
(8.81)
RX ¼ R1 k R2 ffi R1 ; R2 R1 :
(8.82)
and again,
Input bias current compensation might be optional for direct-coupled amplifiers and for capacitively coupled inverting amplifiers, because the resulting
dc offset in the output might be insignificant in some applications. But input bias current compensation is required for a capacitively coupled noninverting amplifier, because otherwise the bias current Ip passes through only the resistance Ri =2 and the resulting voltage is large enough to cause the op amp to saturate. One effect of bias-current compensation in a capacitively coupled non-inverting amplifier is a substantial reduction of the amplifier input resistance, typically from 1 MO or more to approximately RX ¼ R1 k R2 . In a typical application, R2 R1 so the input resistance of a bias-current-compensated capacitively coupled non-inverting amplifier is about the same as that for an inverting amplifier having the same dc voltage gain. If direct coupling to a source is possible, a noninverting amplifier presents a much larger resistance (magnitude) to the source than does a comparable inverting amplifier, but if capacitive coupling is necessary (to block a dc component), a non-inverting amplifier offers no particular advantage over an inverting amplifier in that regard. A capacitively coupled follower would require a dc path to ground from the positive terminal, which would reduce the input resistance and might eliminate the reason for using the follower.
278
8 Capacitance
and the supply voltage (15 V). Assuming railto-rail operation,
Example 8.27. Figure 8.59(a) shows a preliminary design for a two-stage amplifier that will drive a resistive load RL ¼ 2 kO. The available input voltage is vS ¼ VS cosð2pf0 tÞ, with VS 10 mV and f0 50 Hz. The source resistance RS is no larger than 50 O. For frequencies greater than or equal to f0, the minimum overall voltage gain is to be Av ¼ 800, with about equal gain from each stage. The first stage is to be capacitively coupled to the second, as shown, in case imperfect cancellation of the input voltage offset in the first stage produces an undesirable dc component in the first-stage output v1. The available power-supply voltages are VCC ¼ 15 V. The powersupply output resistance and associated wiring resistance is less than 2 O. Complete the design. Include bias-current compensation resistors.
maxðAv Þ ¼
To provide a little margin, we choose, somewhat arbitrarily, Av ¼ 352 ¼ 1; 225: It follows that k¼
800 ¼ 0:653: 1; 225
The feedback networks in the inverting and non-inverting amplifiers are the same, so that the voltage gains of the two stages are approximately the same and approximately equal to 35. We choose R2 ¼ 1MO to minimize the load on each op amp and to allow a large input resistance. Thus, for the inverting amplifier,
Solution: Figure 8.59(b) shows a circuit diagram for the amplifier. The power-supply circuitry is omitted to avoid cluttering the diagram. The voltage gain for frequencies much larger than 50 Hz is not specified, but we know it must be larger than 800. The larger we make the overall high-frequency voltage gain, the smaller will be the parameter k in (8.69) and (consequently) the smaller will be the required coupling capacitance. The maximum allowable voltage gain is determined by the maximum amplitude of the input (10 mV)
R2 R2 ffi 28:6 kO: ¼ 35; R2 ¼ 1MO ) R1 ¼ R1 35 For the non-inverting amplifier, 1þ
R4 R4 ¼ 35; R4 ¼ 1MO ) R3 ¼ ¼ 29:4 kO: R3 34
C
RS
vS
15 V ¼ 1; 500: 10 mV
inverting amplifier
+ –
+
RL non-inverting amplifier
v1 –
(a) R2 R1
C
– +
vS +–
v1
RX
v2 RY R3
Fig. 8.59 See Example 8.27
(b)
+ –
R4
vL RL
8.10 Applications
279
Fig. 8.60 Simulation of the circuit in Fig. 8.59(b)
8.10.8 Switched Capacitor Circuits From (8.80) and (8.82), the bias-current compensation resistances are RX ¼ R2 ¼ 1MO; RY ¼ R3 ¼ 29:4 kO: The lowest frequency of interest is 50 Hz and the input resistance for the second stage is approximately RY . From (8.69), we require a coupling capacitance C¼
k pffiffiffiffiffiffiffiffiffiffiffiffiffi ) C ¼ 93:4 nF: 2pf0 R3 1 k2
The more precise relation (8.70) gives C¼
k 1 pffiffiffiffiffiffiffiffiffiffiffiffi sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2 2 2pf0 R3 1 k k RS RS 2 þ 1 1 k2 R3 R3
Dv i ¼ C ¼ C fs Dv; DT
¼ 93:5 nF: The difference, given typical tolerances on capacitors, is insignificant. Figure 8.60 below shows a simulation of the circuit. The measured voltage gain at 50 Hz is Av ¼
Refer to Fig. 8.61. The circuit diagrams illustrate that the switches are alternately and oppositely open and closed; i.e., when switch 1 is closed, switch 2 is open, and vice-versa. The timing diagram on the right indicates for how long each switch is closed. We assume that the voltages v1 and v2 are approximately constant during any time interval having duration DT. Each time a switch is closed (or open), it remains so for a time DT=2. When switch 1 is closed, the capacitor is discharged. When switch 2 is closed, the capacitor is charged to Dv ¼ v1 v2 , which means that a quantity of charge given by Dq ¼ CDv flows through a load attached to the port on the right. Each time switch 1 is closed, switch 2 is open and no charge flows through the load. The average current through the load over one complete switching cycle is given by
7:999 V ffi 800: 9:998 mV
Dv ¼ v1 v2 ;
(8.83)
where fs ¼ DT 1 is the switching frequency (the number of complete switching cycles per second) and v1 v2 is the voltage across the capacitor when switch 2 is closed. From (8.83) the average current through the capacitor is proportional to the voltage across the capacitor, which means that the switched capacitor acts as a
280
8 Capacitance 1 +
v1 Fig. 8.61 Switched capacitor as a resistor
i
C
–
2
1
2 +
+
v2
v1
–
–
i
v2
C
1
–
+ vC
1
– i
2
+ C
2
i=0
– b + vC
1 +
v1
2
C
– 2
i +
1
–
1
2
ΔT 2
ΔT 2
resistor. By Ohm’s law, the effective resistance of the switched-capacitor arrangement is given by (8.84)
For the analysis above and the resulting relation (8.84) to be valid, the voltages v1 and v2 must be slowly varying relative to the switching frequency fs. We are unprepared for a detailed examination of this issue, but we note that in practice, if the voltages are sinusoidal, the switching rate might be 50–100 times the frequency of the sinusoid. Figure 8.62 shows another switched-capacitor arrangement, where the load is connected from terminal a to terminal b. We assume that the voltages v1 and v2 are approximately constant during any interval of duration DT=2. When the switches are in position 1, the voltage across the capacitor equals v1. When the switches are in position 2, the voltage across the capacitor equals v2 . Thus the voltage across the capacitor changes from v1 to v2 during the time DT=2 that
1
a
v2
–
Dv Dv 1 DT Req ¼ ¼ ¼ : ¼ C fs Dv C fs C i
a
v2
1
–
Fig. 8.62 A switchedcapacitor, negative-resistance circuit
1
1 ΔT 2
ΔT 2
+
v1
2
2 +
2
1
i = –C
v1–v2 ΔT
b
2
the switch is in position 2. The total change in the voltage is Dv ¼ v1 þ v2 . The corresponding change in the charge on the capacitor is Dq ¼ CDv, with the positive direction of charge flow is from right to left, whereas the positive polarity of the voltage vC across the capacitor is from left to right. In other words, during the time DT=2 that the switch is in position 2, the direction of charge flow is from the negative terminal to the positive terminal on the capacitor. The average current during one complete switching period is given by i¼
Dq Dv ¼ C DT DT
and the apparent resistance is given by Req ¼
DT 1 : ¼ C C fs
(8.85)
Thus the circuit in Fig. 8.62 acts as a negative resistance.
8.10 Applications
281
In a circuit, a positive switched-capacitor resistor (Fig. 8.61) can float; that is it is unnecessary for the capacitor and load to have a common ground, because the capacitor discharges through a closed loop. A negative-resistance switched-capacitor filter cannot float (relative to the load) because the capacitor must discharge through the load. In implementations of switched-capacitor resistors, the switches are transistors, which act as single-pole single-throw switches. Thus a capacitor and two transistors are required to implement the single switchedcapacitor positive resistor illustrated by Fig. 8.61. Nonetheless, switched-capacitor resistors often are preferred to ohmic resistors in integrated circuits, for several reasons: • A switched-capacitor resistor can occupy less area on a chip than an equivalent ohmic resistor. • The equivalent resistance of a switched-capacitor resistor can be set precisely (e.g., by adjusting the switching rate), whereas it is difficult to achieve precise ohmic resistances in integrated circuits. • The equivalent resistance of a switched-capacitor resistor can be varied (by varying the switching rate), whereas the resistance of an ohmic resistor is fixed. • In many practical circuits, performance depends not upon the resistance of a single resistor, but instead upon ratios of one resistance to another; e.g., in inverting and non-inverting op-amp amplifier circuits. It is difficult to achieve a precise (single) capacitor in integrated form, but it is not as difficult to achieve precise capacitance ratios. A precise ratio of one switched-capacitor resistor to another in an integrated circuit can be achieved. On the downside, switched capacitors can be noisy (switching transients can contaminate voltages of interest). Also, transistors are not perfect switches, in that they introduce additional voltage drops. The
1 +
Roff
capacitor voltage does not quite reach the source voltage during the charging period and the maximum load voltage is slightly less than the initial capacitor voltage at the beginning of the discharge. Thus there is a minimum source voltage for which a switched-capacitor resistor will work. You will learn more about these issues when you study electronics.
8.10.9 Power Dissipation in SwitchedCapacitor Circuits The electronic switches used in switched-capacitor resistors have a small but non-zero on-resistance Ron when closed and a large but finite off-resistance Roff when open. The on-resistance of the switches ranges from a few microohms to a few ohms and the offresistance from a few megaohms to hundreds of gigaohms, depending upon the devices used. Figure 8.63 shows a circuit model for a switched-capacitor resistor, including the on- and off-resistances of the switches. In the following analysis, we assume Roff Ron , DT Ron C, and that the applied voltage v1 is approximately constant during any interval of duration DT. These assumptions are generally valid for any practical implementation using a switchedcapacitor as a resistor. We assume Roff Ron . For either switch position, the The´venin equivalent resistance seen by the capacitor is RT ¼ Ron Ron þ Roff ffi Ron : Thus the charge and discharge time constants are the same, both given by t ffi Ron C:
Ron
2
Ron
Roff
1
1
v1 –
Fig. 8.63 Circuit model for a switched-capacitor resistor
C
2 0
ΔT 2
ΔT
t
282
8 Capacitance
Switched-capacitor resistors generally are designed such that the capacitor charges and discharges completely each cycle. Thus
The average power dissipated by the switchedcapacitor resistor is given by P¼
t DT: In what follows, we consider a single switching interval beginning when switch 2 is closed, and take the time origin as the beginning of that interval. Let v1 denote the applied voltage (approximately constant) during the interval. While switch 2 is closed, the capacitor charges from zero to
Roff þ Ron v1 ffi v1 : 2Ron þ Roff
While switch 1 is closed, the capacitor discharges from v1 to Ron v1 Ron ffi v1 ffi 0: 2Ron þ Roff Roff The charge placed on the capacitor while switch 2 is closed is given by DQ ffi Cv1 : Thus the energy stored by the capacitor while switch 2 is closed is given by 1 DwC ¼ Cv1 2 : 2 Recall from Section 8.9 that when a capacitor is fully charged by a constant source through a resistance, the total energy provided by the source equals twice that finally stored by the capacitor. Thus the total energy provided by the source in Fig. 8.63 is given by DwS ¼ 2DwC ¼ Cv1 2 :
1
+
Fig. 8.64 Circuit used to calculate power dissipation in a switched capacitor
–
V0
where Req ¼
DT C
is the equivalent resistance of the switched-capacitor resistor. We may conclude that the power dissipated by a switched-capacitor resistor equals that dissipated by an ordinary resistor having the same resistance, provided that (1) the applied voltage is approximately constant during any switching interval, (2) the offresistance of the switches is much larger than the onresistance, and (3) the capacitor charges and then discharges completely during each switching cycle. For the model in Fig. 8.63, the power is dissipated by the switches, because the average power dissipated by an ideal capacitor equals zero. This might not be true in a physical circuit, because physical capacitors are not entirely lossless. In addition to their intentional use as resistors, switched-capacitor configurations are found in memory and logic circuits (in digital computers and other digital systems). In memory and logic circuits, the switched capacitance is mainly device junction capacitance and stray (wiring) capacitance, and predominately the latter. Below, we obtain an expression for power dissipated in such circuits, which bears on power supply and cooling requirements. Refer to Fig. 8.64, where the switch toggles between positions 1 and 2, being in each position for a time DT/2. We assume the time constants R1 C and R2 C for the charge and discharge are both much smaller than the time DT/2, so the capacitor charges fully
2
R1
DwS Cv1 2 v1 2 ; ¼ ¼ DT DT Req
1
1
R2 C ΔT 2
(a) switched-capacitor circuit
2 2 ΔT 2 (b) switch position (periodic)
8.10 Applications
283
(to V0) while the switch is in position 1 and discharges completely while the switch is in position 2. Thus the work done in each position is given by 1 W ¼ CV0 2 2 and the average power dissipated during one complete switching cycle is given by P¼
2W CV0 2 : ¼ DT DT
(8.86)
The switching in Fig. 8.64 is periodic, so the average power (over all time) equals the average power dissipated during any one interval of duration DT. Equation (8.86) can be written P ¼ C V0 2 fs ; fs ¼
1 ; DT
(8.87)
where fs is called the switching frequency. In a digital logic circuit, switching operations are controlled by a clock waveform, which is approximately a square wave. A logic gate can change state at most once during a complete clock cycle. Thus the frequency of the clock driving a switched capacitor is twice the switching frequency fs appearing in (8.87). If DT is the duration of a complete switching cycle, the clock frequency would be fC ¼ 2=DT or DT ¼ 2=fC and (8.87) becomes 1 P ¼ C V0 2 f C : 2
(8.88)
Equation (8.88) is strictly applicable only to a circuit that switches periodically, at a rate fC . However, in a typical memory or logic circuit, there are very many gates switching in what can be modeled as a random pattern. As a result, the total power dissipated can be estimated as PT ¼
N C V 0 2 fC ; 2
(8.89)
where N is the average number of gates that switch during any one clock period.
Example 8.28. In a certain microprocessor, the clock rate is 2 GHz and the logic-level voltage is 1 V. The capacitance associated with each gate or memory cell is about 10 fF (1014 F), which is a realistic value. (a) What is the power dissipation per gate or memory cell? (b) The microprocessor contains a total of 108 gates and memory cells, but on average, only 10% are switching at any given time. If (8.88) is valid, what is the average power dissipated by the microprocessor? Solution: (a) From (8.88), the power dissipation per device is 1 P ¼ CV0 2 fC 2 1 ¼ ð10 fFÞð1VÞ2 ð2 GHzÞ ¼ 10mW: (8.90) 2 (b) If only about 10% of the gates are switching at any given time, the total power dissipated is PT ¼ 0:1 108 ð10 mWÞ ¼ 100 W: Without extra measures for cooling, the microprocessor would become quite hot. Modern microprocessors are packaged with an integral heat sink and fan, and dissipate on the order of 100 W cm2 (chip area). Current projections predict an ultimate density of about 1012 devices per cm2, so heat dissipation will become an even greater problem in the future. Even today, high-performance mainframe computers require elaborate liquid cooling systems. Equation (8.87) has profound implications for highspeed logic design, because it shows that average power dissipated increases only linearly with capacitance, only linearly with switching rate (clock rate), but as the square of the voltage V. Generally, the minimum achievable capacitance is dictated by device geometry and chip layout, whereas demand for increased performance drives the clock rate fc to ever-higher values. As a result, integrated logic-circuit designers are driven to make logic-level voltages as
284
8 Capacitance
small as possible. For example, if the voltage V0 in (8.87) is decreased from 5 to 2 V, the power dissipation is multiplied by the factor (2/5)2¼0.16, which is a decrease of about 84%. Such a reduction has significant implications for power-supply requirements (e.g., battery weight and lifetime) and for measures necessary to remove heat. Example 8.29. The clock rate for a certain integrated logic circuit is 1.2 GHz. By what percentage must the supply voltage be decreased if the clock rate is to be increased by 50% to 1.8 GHZ and the power dissipation must remain the same? Solution: The power dissipated is fixed. From (8.87) sffiffiffiffiffiffi 1 1 fC1 P ¼ CV1 2 fC1 ¼ CV2 2 fC2 ) V2 ¼ V1 fC2 2 2 ffi 0:82V1 : The supply voltage must be decreased by about 18%.
8.11 Problems
Section 8.2 is prerequisite for the following problems. P 8.1 Two metal plates 4 m long and 100 mm wide are parallel and separated by a dielectric whose relative permittivity is 3.5. The capacitance of the arrangement is 35 nF. What is the thickness of the dielectric? Ignore edge effects. P 8.2 Single-layer ceramic disc capacitors usually are made by plating each side of a thin ceramic disk (the dielectric) with a suitable metal, such as silver. The relative permittivities of some ceramics exceed 104 , so ceramic disk capacitors can provide relatively large capacitances in a small volume. The relative permittivity of a particular ceramic is 12,000. What is the thickness of a single-layer disc capacitor utilizing that dielectric if the capacitance is 50 nF, the
diameter is 1 cm, and the thickness of each plate is 25 mm? Neglect edge effects (fringing). P 8.3 Two parallel-plate capacitors C1 ; C2 have the same plate area A. The relative permittivities of the dielectrics are e1 ; e2 . What is the relation between the plate separations if the capacitances are the same? P 8.4 The plates of one parallel-plate capacitor are square, 1 m on a side, and 100 mm apart. The capacitance is equal to that of a second parallel-plate airdielectric capacitor whose plates are 2 4 m and 50 mm apart. What is the relative permittivity er of the dielectric material between the plates of the first capacitor? P 8.5 A parallel-plate air-dielectric capacitor is charged to 100 V and disconnected from the source. The distance between the plates is then halved. What is the new voltage across the capacitor? P 8.6 The capacitance of a certain air-dielectric parallel-plate capacitor is 2 pF. The plate separation is halved and the space between the plates is filled with an oil whose relative permittivity is 400. What is the new capacitance? P 8.7 The capacitance of a certain rectangular airdielectric parallel-plate capacitor is 4 pF. Each dimension of each plate is halved and the space between the plates is filled with a glass whose relative permittivity is 5. What is the new capacitance? P 8.8 Figure P 8.1 shows the circuit-diagram symbol for a varactor diode, which when reverse-biased (when v > 0) acts as a voltage-controlled capacitor having capacitance C¼
C0 : ½1 þ v=v0 a
For a certain varactor diode, C0 ¼ 67 pF, v0 ¼ 1:18 V, and a ¼ 0:44. (a) Construct a graph of capacitance versus voltage for this diode for 100 mV v 100 V. Use logarithmic scales for both axes. (b) Let v ¼ Vdc þ Vac cosð2pf tÞ, with Vdc ¼ 2 V, Vac ¼ 1 V, and f ¼ 10 kHz. Construct a graph of the capacitance versus time (one period).
+
v Fig. P 8.1 See Problem P 8.8
–
8.11 Problems
285 1.2 1
Section 8.3 is prerequisite for the following problems.
0.8 0.6 0.4
P 8.9 The charge on one plate of a certain capacitor is given by
0.2 0 –0.2
qðtÞ ¼ Q0 sinð2pf tÞ; Q0 > 0:
– 0.4 – 0.6
Let Vrms denote the rms voltage across the capacitor and obtain expressions for the capacitance, the rms current Irms through the capacitor, and the ratio Vrms =Irms . P 8.10 Refer to Fig. P 8.2, where C ¼ 400 nF, R ¼ 10:O, and the voltage across the capacitor is as shown. Draw a graph of the current i versus time. P 8.11 Refer to Fig. P 8.3. Draw a graph of the source voltage vS versus time. P 8.12 Figure P 8.4 shows graphs of the voltage v(t) across and current iðtÞ through a capacitor, where vðtÞ ¼ V0 cosð2pf tÞ;
vC (mV)
vC
10
C
R
10 t (μs) 5 –10
Fig. P 8.2 See Problem P 8.10
vC (mV)
vS
+ –
+
RS C
50 2
vC
RS = 10 Ω, C = 100 nF
3 t (μs)
–
1 –50
Fig. P 8.3 See Problem P 8.11
–1 –1.2
0
20
40
60
80
100
120
4
140
160
180
+
vR
–
200
t (μs)
v (t) V0
i (t) I0
Fig. P 8.4 See Problem P 8.12
iðtÞ ¼ I0 sinð2pf tÞ;
with V0 ¼ 5 V and I0 ¼ 31 mA. The current enters the positive terminal of the capacitor. Find the capacitance of the capacitor. P 8.13 The voltage across a capacitor cannot change instantaneously because such change would require infinite current. Can the capacitance of a variable capacitor change instantaneously?
i
– 0.8
vS
+ –
RS
+ C
vC –
Fig. P 8.5 See Problem P 8.14, 15
RS = 50 Ω, C = 50 nF
P 8.14 In Fig. P 8.5, vC ¼ VC cosð2pf0 tÞ. Show that the source voltage can be expressed as a single sinusoidal function of time of the form vS ðtÞ ¼ VS cosð2pf0 t þ yÞ. P 8.15 In Fig. P 8.5, the voltage across the resistor is given by vR ¼ VR cosð2pf0 tþ0:25pÞ, with VR ¼10:64V. Find the voltage vC(t) across the capacitor. P 8.16 Refer to Fig. P 8.6. Obtain an expression for the source voltage vS ðtÞ. Give the values of all parameters in the expression. P 8.17 A variable capacitor is set to 200 pF and connected to a source having open-circuit (available) voltage V0 ¼ 15 V. After it is fully charged, the capacitor is disconnected from the source and the capacitance is increased to 5 nF. What is the new voltage across the capacitor? P 8.18 (i) Show that the circuit in Fig. P 8.7(a) is equivalent at the terminals a–b to the circuit in Fig. P 8.7(b). Thus show that the circuit in Fig. P 8.7(a) is a capacitance multiplier. (ii) What limits the charge (voltage) that can be placed on the capacitor?
286
8 Capacitance
vS (t)
Fig. P 8.6 See Problem P 8.16
+ –
R2
C
π 6 = 15 V, f0 = 1 kHz
vC (t) vC (t) = Vdc +Vac cos ω0t + –
Vdc = 10 V, Vac
Section 8.4 is prerequisite for the following problems.
r n a
R1 = 1 kΩ, R2 = 2 kΩ, C = 25 nF
+
R1
R
–
r
a
o
C ′ = RC / r
p + C
b
b
(a)
(b)
Fig. P 8.7 See Problem P 8.18
1
0
R1
+
+ –
V1
2
C
R2 +
v (t)
V2 –
–
Fig. P 8.8 See Problem P 8.19
P 8.19 Refer to Fig. P 8.8, where vð0Þ < V1 < V2 . The switch is moved from position 0 to position 1 at t ¼ 0, then to position 2 at t ¼ t1, then back to position 0 at t ¼ t2. Sketch neatly and label fully a graph of the voltage v(t) for 0 t t2 . Then give an expression for the voltage v(t) for t > 0. P 8.20 In Fig. P 8.9, the switch is closed at t ¼ 0. The graph shows the voltage across the capacitor for t > 0. Estimate the parameters of the The´venin source. P 8.21 In Fig. P 8.10, the switch is moved from a to b at t ¼ 0, having been at a for a very long time. The graph shows the voltage across the resistor as a function of time. Estimate the source voltage V0 and the capacitance C. P 8.22 A capacitor C ¼ 10 nF in series with a resistor R ¼ 10 O is suddenly connected (at t ¼ 0) to a dc source V0 ¼ 20 V. What is the final ðt ! 1Þ value of the charge (C) on the capacitor? If the initial charge on the capacitor equals zero, what is the initial value of the current? At what time does the charge reach 99% of its final value? 10 8 +
Thevenin source
6
vC (mV) 4
–
2 0
C = 50 nF
Fig. P 8.9 See Problem P 8.20
a
b
V0
C –
R
vR –
R = 1 kΩ
0
1
2
3
4 5 t (μs)
6
7
8
0
1
2
3
4 5 t (μs)
6
7
8
10 8
+
+
Fig. P 8.10 See Problem P 8.21
vC
C
vR (mV)
6 4 2 0
8.11 Problems
287
vin (V) vin
1 1
2
3
R
vout
R
–
10C
vin
C
4
vout
+
t (ms)
C 10
10R
–1
R = 5 kΩ, C = 50 nF
Fig. P 8.11 See Problem P 8.23
vin (V)
vin
1 1
2
3
4
t (ms)
C
vin (V)
vout R
1
–1
1
3
2
4 t (ms)
Fig. P 8.12 See Problem P 8.24
−1 Fig. P 8.13 See Problem P 8.25 RL
R1 + V0
C
R2 –
i
+
vC –
Fig. P 8.14 See Problem P 8.26 b +
–
2V0 +
–
P 8.23 Refer to Fig. P 8.11, where the circuit is in steady state. (a) What is required of R and C if the output voltage is to be approximately equal to the input voltage? (b) Construct plots of the voltage vout ðtÞ versus time for one complete period of the input for C ¼ 100 nF and (a) R ¼ 10 kO, (b) R ¼ 2 kO. (c) Calculate the average power dissipated by the resistor for (i) R ¼ 10 kO and (ii) R ¼ 2 kO. P 8.24 Refer to Fig. P 8.12, where the circuit is in steady state. (a) What is required of R and C if the output voltage is to be approximately equal to the input voltage? (b) Construct plots of the voltage vout ðtÞ versus time for one complete period of the input for C ¼ 100 nF and (i) R ¼ 10 kO, (ii) R ¼ 2 kO. (c) Calculate the average power dissipated by the resistor for (i) R ¼ 10 kO and (ii) R ¼ 2 kO. P 8.25 Refer to Fig. P 8.13, where the output is in steady-state. Sketch a graph of the output voltage vout versus time. You need not determine the voltages involved, but the graph should closely resemble the actual output. P 8.26 In Fig. P 8.14, the switch is closed (at t ¼ 0) after being open for a very long time. Obtain symbolic expressions for the initial and final values of the voltage vC, the initial value of the current i, and the time at which the voltage vC equals 99% of the final value. P 8.27 In Fig. P 8.15, the switch has been at a for a very long time. It is moved from a to b at t ¼ 0 and back to a at t ¼ RC. Sketch neatly and label fully a graph of the voltage vC(t) for 0 t 5RC. P 8.28 A capacitor is charged to a voltage V0 and then connected to two identical resistors through
+
R
a
C
V0
vC –
Fig. P 8.15 See Problem P 8.27 S2
S1 +
R
R
C
vC –
Fig. P 8.16 See Problem P 8.28
switches, as shown in Fig. P 8.16. Switch S1 is closed at t ¼ 0 and switch S2 is closed at t ¼ RC. Sketch neatly and label fully a graph of the voltage vC (t) for 0 t 5RC. P 8.29 A capacitor is charged to a voltage V0 and then connected to two identical resistors and two switches, as shown in Fig. P 8.17. Switch S1 is closed
288
8 Capacitance S2 S1
–
R
S1 +
+ R
+ V0
S2
R
v
V0
R
C
–
C i
–
Fig. P 8.21 See Problem P 8.33
R
+
S1
–
R
+
+ 2V0
a C
R
–
V0
S2
+
–
Fig. P 8.17 See Problem P 8.29
C
V0
b
vC –
Fig. P 8.22 See Problem P 8.34
Fig. P 8.18 See Problem P 8.30
+
R
+ V0 –
vC
C
–
Fig. P 8.19 See Problem P 8.31
t =0
Fig. P 8.20 See Problem P 8.32
+ vC (t)
C
R
–
at t ¼ 0 and switch S2 is closed at t ¼ RC. Sketch neatly and label fully a graph of the current iðtÞ for 0 t 5RC. P 8.30 In Fig. P 8.18, the capacitor is initially uncharged. Switch S1 is closed at t ¼ 0 and switch S2 is closed at t ¼ RC. Sketch neatly and label fully a graph of the voltage vC(t) for 0 t 5RC. Show the time constants associated with each exponential rise. P 8.31 In Fig. P 8.19, R ¼ 2:2 kO 10%, C ¼ 50 nF 20%, and V0 ¼ 10 V. The switch is closed at t ¼ 0. Construct graphs showing upper and lower bounds on the voltage vC(t) for t > 0. P 8.32 If a capacitor is charged to a voltage vC ð0 Þ ¼ V0 and subsequently discharged through a
resistor, as depicted by Fig. P 8.20, the voltage vC(t) decreases exponentially, as vC ðtÞ ¼ V0 expðt=tÞ, where t ¼ RC. You might have heard it said that “theoretically, neither the voltage nor the current ever actually reach zero, but only approach zero asymptotically.” In essence, this problem asks you to evaluate that claim. (a) Can the magnitude of the charge on the capacitor be non-zero and less than that of one electron? Obtain an expression for the time at which the charge on the capacitor becomes less than that of one electron (in magnitude). (b) Let V0 ¼ 10 V, C ¼ 100 nF, and R ¼ 10 kO. Calculate the time defined in part (a). (c) The relation vC ðtÞ ¼ V0 expðt=tÞ is derived from a differential equation under the assumption that charge and current can be represented by real variables. In reality, charge is discrete (is a whole multiple of the charge on one electron). Are the differential equation and the exponential solution valid when only a few electrons participate in the current? P 8.33 In the circuit shown in Fig. P 8.21, switch S2 is closed and switch S1 is open for all t < 0. At t ¼ 0 switch S2 is opened and switch S1 is closed. At t ¼ t1 switch S2 is closed. Finally, at t ¼ t2, switch S1 is opened. (a) Sketch neatly and label fully a graph of the voltage v(t) versus t. Do not assume vðt1 Þ ¼ 0 or vðt2 Þ ¼ 0. (b) Obtain an expression for the voltage v(t). P 8.34 In Fig. P 8.22, the switch is in position a for t < 0 and is moved to b at t ¼ 0. Show that the total energy dissipated in the resistor is independent of the resistance R.
8.11 Problems
Section 8.5 is prerequisite for the following problems. P 8.35 A large, parallel-plate, air-dielectric capacitor is charged to Vab ¼ 50 V. Then a material having relative permittivity er ¼ 4 is inserted halfway between the plates, as illustrated by the shading in Fig. P 8.23. What is the new value of Vab ? Assume the plates are large enough that edge effects are negligible. P 8.36 Refer to Problem P 8.35. One can vary the capacitance of a parallel-plate capacitor by occupying more or less of the space between the plates with a dielectric material, the remainder occupied by air. Describe such a capacitor whose capacitance can be varied from 10 to 50 pF. Assume square plates and a separation of 1 mm. What is the area of each plate? What relative permittivity is required of the inserted dielectric material? P 8.37 Figure P 8.24 shows an air-dielectric variable capacitor having 16 rotating and 15 fixed leaves.18 The distance between each fixed leaf and a neighboring rotating leaf is 500 mm. For simplicity, assume the leaves have the shapes shown, where the cross indicates the centerline of the shaft. Ignore edge effects and the small semicircular bumps on the leaves (for the shaft) and obtain an expression for the capacitance of the capacitor as a function of the angle y. Give the range of the variable capacitance for 0 y p. Is the expression least accurate for y near zero or y near p?
289
P 8.38 In Fig. P 8.25, C2 >C1 and the capacitors are initially uncharged. The switch is closed at t ¼ 0. Which of the two currents i1 ; i2 decreases to 0.1 V0/R first? P 8.39 In Fig. P 8.26, C2 > C1 and the capacitors are initially uncharged. The switch is closed at t ¼ 0. Which of the two voltages v1 ; v2 reaches 0.9 V0 first? P 8.40 Refer to Fig. P 8.27. Capacitors C1 and C2 are individually charged to voltages V1 and V2 , respectively, and then connected in series with a switch and resistor. The switch is closed at t ¼ 0. (a) Obtain an expression for the voltage across the resistor for t > 0. (b) Obtain an expression for the time at which jv(t)j ¼ 0.1jv(0þ)j. P 8.41 An accurate, high-precision capacitor having capacitance C ¼ 51:5 nF is needed in a certain application. The required accuracy and precision are to be obtained as illustrated by Fig. P 8.28, where a fixed capacitor having capacitance C0 ¼ 47 nF 5% is trimmed by a smaller variable capacitor DC while the total capacitance is monitored by a very accurate capacitance meter. (a) Specify the variable capacitor. (b) Could you achieve an equivalent result using a series connection of the same two capacitors? P 8.42 Two identical capacitors having capacitance C ¼ C0 10% are connected in series. Obtain expressions for the capacitance and the tolerance of the series connection. P 8.43 Two identical capacitors having capacitance C ¼ C0 10% are connected in parallel. Obtain expressions for the capacitance and the tolerance of the parallel connection.
Note. The circuit models in Problems P 8.44– P 8.47 below are unrealistic, because they presume that the voltage across a capacitor can change instantaneously. However, the models do allow correct calculation of total charge transfer a b
Fig. P 8.23 See Problem P 8.35
18
Photograph courtesy MTM Scientific, Corp.
P 8.44 Refer to Fig. P 8.29. Obtain an expression for the voltage V2 after the switch is moved from a to b if V2 ¼ 0 before the switch is moved. How much charge is transferred from C1 to C2 ? P 8.45 Refer to Fig. P 8.30. Capacitor C1 is charged to voltage V1 and then connected to the parallel connection of C2 and C3 , which are uncharged. Obtain
290
8 Capacitance
θ
fixed leaf
3cm
2cm
Fig. P 8.24 See Problem P 8.37
4cm
i1
R
i2
+ V1
+ –
C1
V0
C2
C1
C2
C3
–
Fig. P 8.30 See Problem P 8.45
Fig. P 8.25 See Problem P 8.38
C2
v1 –
+
+ + V0 –
R
C1
+
V0
v2
C2
C1
–
–
C3
Fig. P 8.26 See Problem P 8.39 Fig. P 8.31 See Problem P 8.46
V1
+
– +
C1 R C2
Fig. P 8.27 See Problem P 8.40
–
– V2 +
C0
Fig. P 8.28 See Problem P 8.41
+ + V0
v (t)
C1 –
Fig. P 8.29 See Problem P 8.44
C2
V2 –
ΔC
Fig. P 8.32 See Problem P 8.47
+ V01 –
+ C1
C2
V02 –
expressions for the charge on each capacitor (in coulombs) after the switch is closed. P 8.46 Refer to Fig. P 8.31. Capacitor C1 is charged to voltage V0 and then connected to the series connection of C2 and C3 , which are uncharged. Express the voltages across the capacitors after the switch is closed in terms of the initial voltage V0 and the capacitances C1 ; C2 ; C3 . P 8.47 Ideal capacitors C1 ; C2 are charged individually to voltages V01 ; V02 and then connected as shown in Fig. P 8.32. Obtain expressions for the voltages across the capacitors after the switch is closed.
8.11 Problems
291
–
P 8.48 A capacitor is connected in series with a voltage source vðtÞ ¼ V0 cosðo0 tÞ and an rms ammeter having zero internal resistance, as shown in Fig. P 8.33. (a) Assume the leakage resistance of the capacitor is infinite and obtain an expression for the current iðtÞ. Denote the peak amplitude of the current by I0 . (b) Assume the leakage resistance of the capacitor is infinite and express the capacitance in terms of the frequency of the source and the rms amplitudes of the current iðtÞ and the voltage v(t). (c) Assume the leakage resistance is finite and obtain an expression for the current iðtÞ. Denote the peak amplitude of the current by I0 . (d) Assume the leakage resistance of the capacitor is finite and express the capacitance in terms of the leakage resistance, the frequency of the source, and the rms amplitudes of the current iðtÞ and the voltage v(t). P 8.49 A current source is used to charge a capacitor having capacitance C and leakage resistance Rl , as shown in Fig. P 8.34. What is the maximum voltage that can be impressed on the capacitor? If the capacitor is disconnected from the source after being fully charged, how long will it take for the capacitor to discharge?
A
vS (t) +
C
V0
i (t)
Fig. P 8.33 See Problem P 8.48
–
Fig. P 8.35 See Problem P 8.52, 53
P 8.50 Refer to Fig. P 8.34. Under what condition will the final capacitor voltage be within 1% of the voltage available from the source? P 8.51 In Fig. P 8.34, I0 ¼ 10 mA, RS ¼ 1 MO, and the voltage VC is steady at 7 V. (a) What is the leakage resistance of the capacitor? (b) The charged capacitor is disconnected from the circuit and connected to a dc voltmeter having internal resistance Rm ¼ 10 MO. The voltage across the capacitor drops to half its initial value in 8 s. What is the capacitance C? P 8.52 Refer to Fig. P 8.35, where the components have been connected as shown for a very long time and the capacitor has leakage resistance Rl . Under what condition is VC within 0.1% of V0? P 8.53 In Fig. P 8.35, V0 ¼ 15 V and R ¼ 100 kO, and the voltage VC is steady at 14.8 V. (a) What is the leakage resistance of the capacitor? (b) The charged capacitor is disconnected from the circuit and connected to a dc voltmeter having internal resistance Rm ¼ 10 MO. The voltage across the capacitor drops to half its initial value in 4 s. What is the capacitance C? Section 8.7 is prerequisite for the following problems.
+ I0
Fig. P 8.34 See Problem P 8.49, 50, 51
RS
C
VC –
source
VC
P 8.54 Let C denote the end-to-end parasitic capacitance for an axial-lead, cylindrical resistor having resistance R. Assume the voltage across the resistor is given by v ¼ V0 cosðo0 tÞ. Obtain an expression for the frequency f0 at which the rms current through the parasitic capacitance equals 1% of the rms current through the resistor. Calculate the frequency for R ¼ 100 kO and C ¼ 1 pF. P 8.55 The wire-to-wire capacitance of a parallel pair of identical conductors in air far above the ground is given (approximately) by
C
–
+
R
+
Section 8.6 is prerequisite for the following problems.
C¼
p e0 L ; ln½ðd rÞ=r
292
8 Capacitance
where e0 ¼ 8:854 1012 F m1 is the permittivity of free space (or air), d is the center-to-center separation of the wires, r is the radius of each wire, and L is the length of the pair. (a) Find the capacitance of a 100-mile long pair of AWG 00 copper wires 1.2 m apart and well above the ground. (b) A 440 V 60 Hz generator is attached to one end of the wires. Ignoring everything but the wire-to-wire capacitance, what is the rms amplitude of the current drawn from the generator if no load is attached to the far end? P 8.56 Refer to Problem P 8.55. Suppose the AWG wire size used for a certain long-distance power transmission line is increased from AWG 0 to AWG 00. The wires are well above ground. By what factor must the distance between the wires be increased if the wire-to-wire capacitance must remain the same? P 8.57 Proximity to ground increases the wire-towire capacitance of a pair of suspended conductors. The capacitance of such a pair is given by C¼
2p e0 L ; 2hd ln pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi r 4h2 þ d2
12
1
where e0 ¼ 8:854 10 F m is the permittivity of free space (or air), d is the center-to-center separation of the wires, r is the radius of each wire, h is the height of each wire above the ground, and L is the length of the pair. (a) Find the capacitance of a 100-mile long pair of AWG 00 copper wires 1.2 m apart and 20 ft above the ground. (b) A 440 V 60 Hz generator is attached to one end of the wires. Ignoring everything but the wire-to-wire capacitance, what is the current drawn from the generator if no load is attached to the far end? P 8.58 Refer to Problem P 8.57. Suppose the AWG wire size used for a certain long-distance power transmission line is increased from AWG 00 to AWG 000 and the distance between the wires remains the same. The height above ground is much larger than the separation between the wires. Is it necessary to increase the height of the wires above ground if the wire-to-wire capacitance must remain the same? Section 8.9 is prerequisite for the following problems.
R +
Fig. P 8.36 See Problem P 8.60
–
V0
C
P 8.59 Show that the instantaneous energy wðtÞ stored in the electric field in an ideal capacitor is given by wðtÞ ¼
1 2 Q ðtÞ; 2C
where C is the capacitance and Q is the charge on either plate. P 8.60 Refer to Fig. P 8.36, where the capacitor is initially uncharged and the switch is closed at t ¼ 0. Show that for t ! 1 the total energy dissipated in the resistor equals the total energy stored in the capacitor. P 8.61 To increase the energy-storage capability of a capacitor, should one increase or decrease the thickness of the dielectric? P 8.62 Show that the stored energy per unit volume (per m3 ) for a capacitor is given by w 1 ¼ er e0 E2 ; vol 2 where E is the electric field strength ðVm1 Þ in the dielectric. P 8.63 Refer to Problem P 8.62. How does the maximum stored energy per unit volume (volumetric energy density) for a capacitor compare with that for gasoline? P 8.64 Refer to Problem P 8.8. The parameters of the varactor diode are C0 ¼ 50 pF, v0 ¼ 1 V, and a ¼ 0:5. The voltage across the varactor diode is given by v ¼ Vdc þ Vac cosð2pf tÞ; Vdc ¼ 500 mV; Vac ¼ 100 mV; f ¼ 20 kHz: Calculate the average power dissipated by the varactor diode. Section 8.10 is prerequisite for the following problems. P 8.65 Refer to Fig. P 8.37, where the input is sinusoidal, having frequency f, and the op amp is
8.11 Problems
293 R1
R2
vin
vout
–
C
C
+
vin
R2
R1
vout
– +
Fig. P 8.37 See Problem P 8.65 Fig. P 8.40 See Problem P 8.68
vin
vout
+ – C
vin
vout
+ –
R R
C
Fig. P 8.38 See Problem P 8.66 Fig. P 8.41 See Problem P 8.69 C
vin
R2
R1 –
vout
+
Fig. P 8.39 See Problem P 8.67
ideal. Under what conditions is the output approximately proportional to the derivative of the input? P 8.66 Refer to Fig. P 8.38, where the input is sinusoidal, having frequency f, and the op amp is ideal. Under what conditions is the output approximately proportional to the derivative of the input? P 8.67 Refer to Fig. P 8.39, where the input is sinusoidal, having frequency f, and the op amp is ideal. Under what conditions is the output approximately proportional to the integral of the input? P 8.68 Refer to Fig. P 8.40, where the input is sinusoidal, having frequency f, and the op amp is ideal. Under what conditions is the output approximately proportional to the integral of the input? P 8.69 Refer to Fig. P 8.41, where the input is sinusoidal, having frequency f, and the op amp is ideal. Under what conditions is the output approximately proportional to the integral of the input? P 8.70 A 15 V supply having internal resistance RS ¼ 1 O supplies power to ten circuits, each of which represents an average load of 10 O and each of which is bypassed at its power pin by a 50 nF capacitor.
(a) What is the steady-state current that must be provided by the supply? (b) What is the initial current (when the circuit is first energized and all capacitors are discharged)? (c) What is the time constant for the initial surge current and what is the total additional energy that must be provided by the supply during the initial surge? (d) By what factor is the additional energy multiplied if each bypass capacitance is doubled in an attempt to further reduce ripple? P 8.71 In the absence of a bypass capacitor, the ripple factor at the power pin of a certain circuit is 0.015. A 10 nF bypass capacitor reduces the ripple factor to 0.002. What bypass capacitance is required to reduce the ripple factor to 0.0001? P 8.72 Without bypass, the ripple factor at the power pin of a certain circuit is 0.02. The ripple is approximately sinusoidal, with a frequency of 180 Hz. A 75 mF bypass capacitor reduces the ripple factor to 0.002. What is the The´venin-equivalent resistance at the power pin? P 8.73 A certain digital IC has eight outputs. The load seen by each is equivalent to a 40 pF capacitor, and the logic-level voltage and the supply voltage are both 5 V. The outputs can change state in 4 ns. (a) What is the additional supply current (pulse) demanded by the IC if all eight outputs switch from off (0 V) to on (5 V) at once? (b) What bypass capacitance should be used at the IC’s power pin if the IC is clocked at 100 MHz (the minimum duration of a state
294
8 Capacitance
is 10 ns) and the supply voltage must be held to within 1% of the nominal value? P 8.74 Figure P 8.42 shows a simulation of a halfwave rectifier circuit. Multimeter XMM2 indicates XMM2
+
V1
+ −
RS
D1
10 Ω
DIODE_VIRTUAL
XMM1
−
+
C1 200 uF
170 V 60 Hz 0Deg
−
RL 100 Ω
the rms amplitude of the ac (ripple) component of the load voltage and multimeter XMM1 indicates the dc component, where for C ¼ 200 mF, the rms amplitude of the ripple is approximately 19.1 V and the dc component of the load voltage is approximately 102.5 V (a) What is the ripple factor for the circuit as shown? How good is the agreement of the measured ripple factor with the approximate formula developed in the text? Use the approximate relation developed in the (b) text to find the capacitance needed to reduce the ripple factor to 0.015. Then use a simulation to determine the actual ripple for that value of capacitance. Be sure to give the simulation time to achieve steady state (wait until the voltage readings change very little with time). (c) For the capacitance found in part (b), what is the worst-case (maximum) current through the diode when the circuit is first switched on? P 8.75 Figure P 8.43 shows a simulation of a fullwave rectifier circuit, with an oscillograph of the ac (ripple) component load voltage and measurements
Fig. P 8.42 See Problem P 8.74
XMM1
RS 10 Ω
+ D3
−
XMM2 +
D1
−
170 V 60 Hz 0Deg
+
+
DIODE_VIRTUAL DIODE_VIRTUAL
D4 DIODE_VIRTUAL
Fig. P 8.43 See Problem P 8.75
Exl Trlg
D2 DIODE_VIRTUAL
C 2400 uF
RL 100 Ω
−
B
A
V1
+
XSC1
−
−
+
−
8.11 Problems
295
of the dc load voltage ðffi 121 VÞ and rms ripple ðffi 1:27 VÞ. Note that the source floats. (a) What is the load-voltage ripple factor? (b) Trace the paths traveled by the current i for vS > 0 and vS < 0. If the capacitor is removed (if iL ¼ i), what is the waveform of the load voltage vL ? (c) Use the relation C¼
T pffiffiffiffiffi RL g 12
developed in the text to calculate the capacitance required to reduce the ripple factor to 0.005. Use a simulation to check the result. Be sure to give the simulation time to achieve steady state. P 8.76 Figure P 8.44 shows a full-wave rectifier circuit using two identical sources. (a) Trace the paths traveled by the current i for vS >0 and vS <0. If the capacitor is removed (if iL ¼ i), what is the waveform of the load voltage vL ? (b) Simulate the circuit and plot the steady-state load voltage waveform for C ¼ 1; 000 mF. Measure the rms amplitude of the ripple voltage and the dc component of the load voltage. Calculate the ripple from both the measured values and the formula developed in the text. (c) What capacitance would be required to reduce the peak-to-peak ripple to 1 V? (d) Simulate the circuit using the capacitance you found in part (c) and verify your calculation.
vS + –
P 8.77 Refer to Fig. P 8.45. Specify the coupling capacitors such that the overall voltage gain equals or exceeds 450 for all frequencies of interest. The source resistance is negligible, the op amps are ideal, and the output resistance of each stage is negligible. Use a simulation to check your work. P 8.78 Refer to Fig. P 8.46. What coupling capacitance C is required if the voltage gain for f0 ¼ 1 kHz must be at least 95% of the voltage gain for f0 ¼ 10 kHz? Use a simulation to check your work. P 8.79 (a) Specify the components of a cascade of two or more inverting amplifiers such that the overall voltage gain would be 104 if the amplifiers were direct coupled. The feedback resistances cannot exceed 1MO and the input resistance of each inverting amplifier must be at least 25 kO. Assume the op amps are ideal. (b) In actual use, the source will be capacitively coupled to the first stage, each stage will be capacitively coupled to the next, and a 10 kO load resistance will be capacitively coupled to the last stage. The overall voltage gain must be at least 9800 for any sinusoidal input whose frequency exceeds 1 kHz. Specify the coupling capacitors. Use a simulation to verify your design. (c) P 8.80 Refer to Fig. P 8.47. Specify the coupling capacitors such that the overall voltage gain at 1.5 kHz
C RL= 100 Ω, vS = VS sin(2p ft) VS = 170 V, f = 160 Hz
i vS + –
(e) If the source resistance for each source is 5 O, what is the maximum possible surge current through either diode?
C
vS +–
+ R1
RL
+ – mv 1
v1 –
+
R2 RL
vL –
vS = VS cos(2pf0t), R1 = 5MΩ, R2 = 100 Ω, RL = 1 kΩ, m = 800
Fig. P 8.46 See Problem P 8.78
Fig. P 8.44 See Problem P 8.76
R4
R2 R1 –
vS
Fig. P 8.45 See Problem P 8.77
+ –
+
C1
R3
–
C2
+
R1 = 25 kΩ, R2 = 500 kΩ, R3 = 20 kΩ, R4 = 500 kΩ, RL = 5 kΩ Vcc = 25V, vS = VS cos(2p f0t); VS ≤ 40 mV, f0 ≥ 100 Hz
RL
296
8 Capacitance R2
R2 RS
vS
+ –
R1
R1
C2
–
vL
–
+
R2
+
vS = V0 + VS cos(2pf0t), f0 ≥ 1.5 kHz, V0 = 500 mV, VS ≤ 2 mV RS =100 Ω, R1 = 15 kΩ, R2 = 305 kΩ, Vcc = 15 V
Fig. P 8.47 See Problem P 8.80
C1
R1
C1
+ –
vS
R2
R1
10 V
C2
–
RL
C
vS
+
+ –
RL
+
vL 1 ms
–10 V
RL = 10 kΩ
Fig. P 8.48 See Problem P 8.81
t
1 ms
–
Fig. P 8.50 See Problem P 8.83
Rleak
R2
vS
+ –
C
C v1
+ RL
R1 –
vL –
+
+ –
vS
vL RL
RL = 10 MΩ, vS = VS cos(2p ft)
Fig. P 8.49 See Problem P 8.82
vS (mV)
is at least 98% of the gain would be achieved if the stages were direct coupled. Use a simulation to verify your design. P 8.81 Refer to Fig. P 8.48. The source resistance is negligible and the op amp is ideal. (a) The overall high frequency voltage gain must be 50 dB. The voltage gain at 30 Hz must be no less than 49 dB. Specify the components. (b) The maximum amplitude of the input is 100 mV. What is the minimum acceptable supply voltage? Assume a symmetric supply and rail-to-rail operation. (c) Perform a simulation to verify your design. P 8.82 In Fig. P 8.49, the leakage resistance Rleak is ignored and the coupling capacitance C is specified such that VL rms ¼ 0:8 VS rms for f ¼ 30 Hz. It is subsequently found that the capacitor leakage resistance is approximately equal to the load resistance RL . What is the actual value of VL rms =VS rms for f ¼ 30 Hz? In Fig. P 8.50, the source is a square P 8.83 wave, as shown. In steady state, the load voltage vL must be within 5% of the input vS at all times. Specify
100
t (ms)
0 0
2
8
Fig. P 8.51 See Problem P 8.84
the coupling capacitor C. Use a simulation to verify your answer. P 8.84 Refer to Fig. P 8.51, The source resistance is negligible and the load resistance is RL ¼ 5 kO. The op amp is rail-to-rail and otherwise ideal. The input vS ðtÞ is a rectangular pulse train, as shown. Let vS ac ðtÞ denote the ac component of the input. The circuit is intended to amplify the ac component of the input, such that vL ðtÞ ffi 100 vS ac . The absolute error j100vS ac vL ðtÞj must not exceed 100 mV. Specify the circuit components.
8.11 Problems C + –
vS
297 v1
vL
+ –
R1 R1
P 8.85 Refer to Fig. P 8.52. Specify the capacitor such that the voltage v1 is always within 1% of the ac component of the source voltage vS. Then determine the maximum percent difference between the load voltage vL and a true rectangular pulse train. Use a simulation to check your work. P 8.86 In Fig. P 8.53, RL ¼ 5 kO, R1 ¼ 20 kO, R2 ¼ 1MO, C ¼ 50 nF, the op amp is ideal, and the supply voltages are 20 V. The source vS has a constant (dc) component and one sinusoidal (ac) component; i.e.,
RL
R2
R1 = 10 kΩ, R2 = 1MΩ, RL = 20 kΩ
vS (mV) 50
0
0
20
t (ms)
80
Fig. P 8.52 See Problem P 8.85
v1 vS
+ –
C
vS ðtÞ ¼ VDC þ VAC cosð2pf0 tÞ:
RX R1
Specify the resistance RX . What is the lowest frequency for which the voltage gain for the ac component of the source exceeds 30 dB? P 8.87 In Fig. P 8.54, the source vS has one constant and one sinusoidal component. Specify the resistors and the capacitor such that the voltage gain equals 30 dB at 50 Hz. P 8.88 Figure P 8.55 shows two amplifiers in cascade. The op amps are ideal. At 1 kHz, the voltage gain and input resistance of each amplifier (not including the capacitors) are approximately 35 dB and 10 kO. What are appropriate values for the inputbias-current compensating resistors RX ; RY ? P 8.89 Figure P 8.56 shows two amplifiers in cascade. The op amps are ideal. At 1 kHz, the voltage gain and input resistance of each amplifier (not including the capacitors) are approximately 40 dB and
vL
+ –
RL
R2
Fig. P 8.53 See Problem P 8.86 R2
C
vS
R1
vL
–
+ –
+ RL
RX
Fig. P 8.54 See Problem P 8.87
R2 C1
vS
R1
C2
– +
+ –
v1
RY
RX
Fig. P 8.55 See Problem P 8.88
R1
C1 + –
Fig. P 8.56 See Problem P 8.89
v2
vS
+ –
RX
R2
vL RL
R2
C2 + –
RY R1
+ –
R3
R4
vL RL
298
8 Capacitance
10 kO. What are appropriate values for the input-biascurrent compensating resistors RX ; RY ? P 8.90 Figure P 8.57 shows two amplifiers in cascade. The op amps are ideal. At 1 kHz, the voltage gain and input resistance of each amplifier (not including the capacitors) are approximately 25 dB and 20 kO. What are appropriate values for the inputbias-current compensating resistors RX ; RY ? P 8.91 Refer to Fig. P 8.58, where the timing diagram indicates which switch is closed, as a function of time. Obtain a symbolic expression for the equivalent resistance of the switched capacitor. Then use the equivalent resistance to calculate the dc component (average value) of the load voltage vL . Simulate the
circuit to confirm your answer. Discuss the practicality of this particular switched-capacitor implementation. P 8.92 Refer to Fig. P 8.59. The switches are in position 2 and the capacitors are uncharged at t ¼ 0, at which time the switches begin operating as indicated by the timing diagram. (a) Plot the voltage v(t) versus time for 0 t 10 ms. (b) Replace the switched capacitor by an equivalent resistor and plot the voltage v(t) on the axes used in part (a). Do the two circuits exhibit the same (or very similar) transient response? P 8.93 Refer to Fig. P 8.60. Switches 1 and 2 operate as indicated by the timing diagram. The voltages v1 and v2 are approximately constant during any interval R4
R2 C1 + –
Fig. P 8.57 See Problem P 8.90
R1
vS
C2
–
R3 +
RX
S2
closed
+
+
RL
C
–
vL
open
1
2
1
1
2
1
2
+
2
+
C1
2
2
– 1
closed
+
Fig. P 8.60 See Problem P 8.93
1
1 ΔT
ΔT 2
0
3ΔT 2
2ΔT L
t
2
1
a +
2ΔT L
v
C2
V0 = 10 V, C1 = 20 nF, C2 = 100 nF, ΔT = 2 ns , Rs = 10W
Fig. P 8.59 See Problem P 8.92, 96
3ΔT 2
1 2
V0
t
ΔT
ΔT 2
0
switch position
Rs 1
–
2
–
V0 = 10 V, C = 100 pF, RL= 1 kΩ, ΔT = 1 μs
Fig. P 8.58 See Problem P 8.91
RL
RY
S1 V0
vL
–
+
2
C
vC –
2
1
2
1
1
2
1
2
ΔT 2
ΔT 2
c 1
+
v1
v2
–
–
b
d
open
t
8.11 Problems
299 S1
a
b
Fig. P 8.61 See Problem P 8.94
i
S2
C1
closed
2
1
2
1
open
1
2
1
2
ΔT 2
ΔT 2
C2
+ V –
t
switch position 1 0
+ –
2
C1
2 +
C2
vout
V0
1
–
(a) Plot the energy stored in C2 versus time for 0 t 10 ms. (b) On the same axes, plot the cumulative work done by the source for 0 t 10 ms.
1
1 ΔT 2
0
Fig. P 8.62 See Problem P 8.95
of duration DT=2. (a) Show that the circuit is approximately equivalent to a resistor and obtain an expression for the resistance. (b) While terminals a–b are open and the switches are operating as described above and at a very fast rate, a resistor RL and capacitor CL are connected in parallel and then to terminals c–d. Then a voltage source v1 ðtÞ ¼ V0 is connected to terminals a–b. Assume the switched capacitor can be represented by its equivalent resistance and obtain an expression for the output v2 ðtÞ. P 8.94 Refer to Fig. P 8.61, where the switch positions alternate, as indicated by the timing diagram. Obtain expressions for (a) the time average of the current i, (b) the equivalent resistance at the terminals a–b, (c) the average current through each switch. P 8.95 In Fig. P 8.62, V0 ¼ 10 V, C1 ¼ 5 nF, C2 ¼ 100 nF and DT ¼ 2 ns. The switch is at position 0 for t < 0 and begins toggling between positions 1 and 2 thereafter, as indicated by the timing diagram. The capacitor C2 is initially uncharged, such that vout ð0Þ ¼ 0. (a) Plot the voltage vout versus time for 0 t 200 ns. P 8.96 Refer to Fig. P 8.59 (Problem P 8.92). The capacitors are uncharged for t ¼ 0, at which time the switches begin operating as indicated by the timing diagram.
2
t=0
ΔT
3ΔT 2
t
2ΔT L
Req +
+
vout
C2
V0 –
–
Fig. P 8.63 See Problem P 8.96
v1
1
R1 C1
R2
1
C2
V0
i1
ΔT 2
v2
2
i2
1 2
1 2
ΔT
V0 = 10 V, R1 = 100 W, C1 = 10 nF, R2 = 50 W, C2 = 50 nF, ΔT = 2ns
Fig. P 8.64 See Problem P 8.97
(c) Find the equivalent resistance Req of the switched capacitor. Use the equivalent RC circuit model shown in Fig. P 8.63 and plot the energy delivered by the source and the energy stored in C2 for 0 t 5t, where t is the time constant for the equivalent RC circuit. Are the results consistent with those obtained in parts (a) and (b)? P 8.97 Refer to Fig. P 8.64, Plot the voltages v1(t) and v2(t) and the instantaneous power delivered by the source on the same axes. P 8.98 Refer to Fig. P 8.65, where the switch operates as indicated by the timing diagram. (a) Obtain an expression for the average power delivered by the
300
8 Capacitance 2
V0
2
2
2
C
+
1 1
1
– 0
Fig. P 8.65 See Problem P 8.98, 99
2
2
+ –
ΔT 2
C1
1
1
vL
+ –
2
RL
1 2
C2
V0
1
1 2
ΔT
Fig. P 8.66 See Problem P 8.100
R1 +
Fig. P 8.67 See Problem P 8.101
t
ΔT
ΔT
–
2
1 2
V1
source. (b) It is shown in the text that the average power dissipated by a capacitor equals zero. If that is the case, where is the power delivered by the source dissipated? P 8.99 Refer to Fig. P 8.65, where the switch operates as indicated by the timing diagram. (a) Obtain an expression for the energy stored in the capacitor while the switch is in position 2. (b) Obtain an expression for the work done by the source while the switch is in position 2. (c) Why are the expressions obtained in parts (a) and (b) different?
C
1
ΔT 2
R2
1
1
1
+ V2
–
2
2 ΔT
P 8.100 Refer to Fig. P 8.66, where the op amp is ideal and the switches have been operating as indicated for a very long time. The source resistance (not shown) is small but it is not zero. What is the average power delivered by the source V0? P 8.101 Refer to Fig. P 8.67, where the switches have been operating as indicated for a very long time. Assume that DT is much larger than each of t1 ¼ R1 C and t2 ¼ R2 C. Obtain an expression for the power delivered by the sources (dissipated in the circuit).
Chapter 9
Inductance
A phenomenon called inductance is analogous to capacitance, but with the roles of current and voltage swapped. Whereas capacitance stores energy in an electric field produced by voltage, inductance stores energy in a magnetic field produced by current. Whereas capacitance resists changes in terminal voltage, inductance resists changes in terminal current. Inductance is relatively unimportant in low- to midfrequency, low-power electronic circuits, where its desirable effects can be obtained by other means, but is important in high-frequency circuits and in electric power generation and distribution systems. Because inductance arises from a magnetic field, we begin with a discussion of magnetic fields.
9.1 Magnetic Field If you sprinkle iron filings on a sheet of paper overlaying a magnet, the filings will arrange themselves along curved lines exiting (by convention) the north pole of the magnet and entering the south pole, as illustrated in Fig. 9.1. It is said that the magnet produces a magnetic field characterized by lines of force that align the filings. The stronger the magnet, the greater the density of lines passing through any plane perpendicular to the surface of the paper. Capitalize Magnetic flux, denoted by f, is a measure of the density of the lines. The SI unit of magnetic flux is the weber (Wb).1 Energy is stored in a magnetic field because the field has the potential of doing work on magnetic
material. For example, suppose we fix a strong magnet to a smooth surface and place a piece of iron against one of the poles of the magnet. Then we move the iron a short distance away from the magnet against the force of attraction. If we then release the iron, the field will do work on the iron by accelerating it toward the magnet. When we move the iron away from the magnet, we store energy in the field. When we release the iron, the iron gains kinetic energy from the field equal to the energy we stored in the field (ignoring friction). A moving charge (current) produces a magnetic field. In introductory physics books, it is shown that the magnetic flux produced by a current in a long straight wire is concentric to the wire, as illustrated in Fig. 9.2. The direction of the magnetic flux produced by a current in a wire can be determined using the right-hand rule: If you wrap the fingers of your right hand around the wire with your thumb pointing in the direction of the current, your fingers point in the direction of the flux.2 The flux produced by the current is proportional to the current. So long as the current is steady, the field is steady, and there is no energy exchange between the field and the current producing the field. But energy is exchanged between the field and a changing current. If the current increases then the flux, being proportional to the current, increases as well and the energy stored in the field increases. If the current decreases, then the flux decreases and the field returns energy to the current. Because work must be done to store energy in or extract energy from the field, the magnetic field
2 1
After the German physicist Wilhelm Eduard Weber (1804–1891).
Of course, if you actually do this with a “live” wire, all of your appendages could point in different directions.
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_9, # Springer ScienceþBusiness Media B.V. 2011
301
302
9 Inductance
duce a current in the direction of the current already present. If the current is increasing, the induced voltage tends to produce a current in the direction opposite to that of the current already present. Because magnetic flux is proportional to the current that produces the flux,4 the flux linkage with a conductor also is proportional to the current producing the flux and we may write l ¼ L i; Fig. 9.1 Iron filings reveal magnetic lines of force from a permanent magnet
Fig. 9.2 Magnetic flux arising from current in a conductor
produced by a current always acts to oppose any change in the current. The magnetic field gives a kind of inertia to the moving charges comprising the current.
9.2 Self Inductance The magnetic field produced by a current in a conductor opposes a change in that current by inducing a voltage that tends to keep the current from changing. The induced voltage v is given by Faraday’s law of induction3 v¼
dl ; dt
(9.1)
where l is the magnetic flux linkage with the conductor. Flux linkage l depends upon both the quantity f of flux in the space containing the conductor and the geometry of the conductor; e.g., if a quantity f of flux links every turn of an N-turn coiled conductor, the flux linkage is l ¼ N f. The polarity of the induced voltage is that which opposes a change of flux (Lenz’s law). If the current is decreasing, the induced voltage tends to pro-
where L is a constant of proportionality called inductance. The SI unit of inductance is the henry5 (H), where 1 H equals 1 Vs A–1. If the flux that induces a voltage in a conductor is due entirely to current in the same conductor, the associated inductance is called self-inductance. It also is possible for flux produced by current in one conductor to induce a voltage in another conductor, in which case the associated inductance is called mutual inductance. In practice and in this book, inductance alone means self-inductance. If mutual inductance is meant, the adjective mutual is included. Inductance depends strongly upon the geometry of the conductor carrying the current and the medium in which the field is produced (e.g., air versus iron). The inductance of a conductor is increased by winding the conductor in a coil, as illustrated in Fig. 9.3. In this configuration, the flux produced is greater than that for a straight wire carrying the same current because the current enclosed by and creating flux loops is effectively N times the current in a single conductor, where N is the number of turns in the coil. Thus the total flux produced is N times that produced by a single conductor: f ¼ Nf1 :
After the English chemist and physicist Michael Faraday, (1791–1867). Faraday’s law of induction is treated in virtually all introductory physics textbooks.
(9.3)
In (9.3), the flux f1 is proportional to the current producing the flux; i.e., f1 ¼ k i. Furthermore, flux linkage with an N-turn coil is N times that for a straight conductor because each loop links the coiled conductor N times. Thus 4
3
(9.2)
This assertion must be modified for flux produced in a magnetic material by relatively large currents. We ignore that refinement here. 5 After the American physicist Joseph Henry (1791–1878).
9.3 Inductance of Air-Core Coils
303
Exercise 9.1. What is the SI unit of k in (9.7)? Flux loops near each end of a coil do not link as many turns as those near the middle. The associated reduction in the total flux linkage can be neglected in long coils. But for short coils, it is necessary to correct for the reduced flux linkages. Various handbooks give various formulas for short coils, one being Fig. 9.3 Magnetic flux produced by current in a coil
l ¼ N f ¼ N ðN f1 Þ ¼ k N 2 i ¼ L i;
L¼ (9.4)
where, from (9.2), inductance L is given by L¼
l ¼ k N2 i
(9.5)
The flux produced by current in a coil (and thus the inductance of the coil) can be further increased by winding the coil around a magnetic material, such as iron. The direction of the flux is again determined using a right-hand rule: Imagine wrapping the fingers of your right hand around the coil in the direction of the current; your thumb then points in the direction of the flux through the center of the coil.
9.3 Inductance of Air-Core Coils The inductance of a long, tightly wound, single-layer, helical air-core coil having N turns, length l, and diameter d is given by6 L¼
p m 0 N 2 d 2 m0 N 2 A ¼ ; 4l l
(9.6)
where m0 ¼ 4 p 107 H m1 is the permeability of a vacuum (also very nearly that of air), A ¼ pd 2 4 is the cross-sectional area of the coil, and long means l d. We may write (9.6) as L ¼ k N2 ;
(9.7)
in agreement with (9.5). 6
This relation is derived in all introductory, university-level physics textbooks.
m0 N 2 d 2 ; ð0:579 d þ 1:273 lÞ
(9.8)
where N is the number of turns, d is the diameter of the coil and l is the length of the coil. Equation (9.8) is accurate to about 1% for tightly wound, singlelayer, helical, air-core coils.
Example 9.1. Find the number of turns needed on a paper tube 10 cm long and 1 cm in diameter to produce an inductor having inductance L ¼ 1 mH. Assume the coil is helical and tightly wound in a single layer. Solution: From (9.8), sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð0:579 d þ 1:273 lÞL N¼ m0 d 2 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð0:579Þð1 cmÞ þ ð1:273Þð10 cmÞ ¼ ð1 mHÞ ð4p 107 Hm1 Þð1 cmÞ2 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ð13:31 cmÞð1 mHÞ ¼ ð4p 107 Hm1 Þð1 cmÞ2 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 13:31 mH ¼ ð4p 107 Hm1 Þð1 cmÞ sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 13:31 mH ¼ ð4p 107 Hm1 Þð0:01 mÞ sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 13:31 103 H ¼ 1029: ¼ ð4p 109 HÞ
304
9 Inductance
Exercise 9.2. If the coil in Example 9.1 occupies the full length (10 cm) of the paper core and the thickness of the insulation is negligible, what is the maximum diameter of the wire? If the wire is copper, what is the resistance of the coil?
9.4 Inductors Inductance can be introduced in circuits using components called inductors, to achieve certain desired effects. Figure 9.4 shows several inductors. Inductors are constructed by winding wire around a core, which might be air (a paper or plastic tube), iron, or other material. Inductors wound on a core of non-magnetic material, such as paper or plastic are called air-core inductors and inductors wound on a core of magnetic material such as iron, ferrite, or steel are called ironcore inductors.
Fig. 9.4 Assorted inductors (not to scale): (a), (b) small radial-lead inductors, (c) small ferrite-core noise-suppression inductor, (d), (e) surfacemount inductors, (f) highcurrent PCB inductor, (g) axial-lead high-current inductor, (h) toroidal inductor (Photographs courtesy of Rapid Electronics, Ltd)
Figure 9.5 shows circuit-diagram symbols for inductors. Figure 9.5(a) shows the conventional circuit-diagram symbol for an air-core or ideal inductor having inductance L. Figure 9.5(b) shows a variation sometimes used to denote an inductor wound on a core made of iron (or other magnetic material). Figure 9.5(c) shows the conventional symbol for a variable inductor, almost all of which have magnetic cores. A common type of variable inductor has a threaded cylindrical magnetic core. The inductance is varied by screwing the core farther into or out of the coils constituting the winding. As has become common practice, we use the symbol in Fig. 9.5(a) for an inductor, regardless of the core material. We also limit our treatment to inductors that are linear under normal operating conditions. Because of the way they are constructed, inductors sometimes are called coils. Because of their purpose in certain applications, some iron-core inductors sometimes are called chokes. Often, iron-core inductors used in power supplies are called chokes, and ironcore and air-core inductors used in other applications
9.5 Terminal Characteristic of an Inductor
L (a) fixed, air-core
305
L (b) fixed, iron-core
Fig. 9.6 Symbol for an inductor, annotated in agreement with (9.9)
L
v
–
L
Several implications of (9.9) are noteworthy:
are called coils, but this terminology is neither standard nor universal. Inductance is introduced intentionally in circuits for various purposes, some of which are described in the sequel. In most applications where either inductance or capacitance could be used, such as in active filters and integrating and differentiating circuits, capacitance is preferred because of the smaller size and lower cost of capacitors, relative to inductors. Also, it is easier to produce a capacitor than an inductor of comparable precision in an integrated circuit, and it is easier to confine the electric field in a capacitor than it is to confine the magnetic field produced by an inductor, so capacitors produce less electrical interference than inductors. Nonetheless, there are important applications for inductors, especially in some power supplies and in high-frequency circuits, where they are used in conjunction with capacitance to build very selective filters. Inductance is especially important in circuit models for electric power generation and distribution systems, because generators, motors, and transformers exhibit significant inductance. Inductance is only occasionally encountered in low- to moderate-frequency electronic circuits, where desirable effects of inductance can be introduced in other ways (avoiding need for bulky and heavy coils).
9.5 Terminal Characteristic of an Inductor Using (9.2), we may rewrite Faraday’s law (9.1) as di ; dt
+
(c) variable, iron-core
Fig. 9.5 Circuit-diagram symbols for inductors
v¼L
i
(9.9)
where v is the voltage across the terminals of an inductor and i is the current entering the terminal designated positive, as shown in Fig. 9.6. Equation (9.9) is one expression of the terminal characteristic of an inductor.
• The voltage across an inductor is nonzero whenever the current through the inductor is changing (when di=dt is nonzero) and is zero otherwise. An inductor acts as a conductor (a short circuit) for constant current. • The magnitude of the voltage across an inductor is proportional to the rate of change of the current through the inductor. The faster the current changes, the larger is the opposing voltage. An inductor opposes changes in the current through the inductor. • Changing the current through an inductor instantaneously would require infinite voltage across the inductor. Thus, in physical circuits, the current through an inductor is a continuous function of time. In other words, the current though an inductor cannot change instantaneously. • The voltage across an inductor is proportional to the inductance L. More voltage is required to change the current through an inductor at a specified rate in a larger inductor than a smaller one. Conversely, for a fixed rate of change in current, a large inductance produces a larger induced voltage than does a smaller inductance. A circuit in which all currents and voltages are constant is said to be in dc steady state. If the current through an inductor is constant, the voltage across the inductor is zero. Thus, for any circuit in dc steady state, all inductors in the circuit are effectively short circuits. Example 9.2. Figure 9.7(a) shows the current in an inductor having inductance L. From (9.9) the resulting (induced) voltage across the inductor is the product of the inductance and the derivative (instantaneous slope) of the current. Figure 9.7(b) shows the voltage across the inductor, where v1 ¼
Li1 ; t1
v2 ¼
Lði2 i1 Þ : t4 t2
306
9 Inductance v(t)
i(t) i1
v1 t3 t1
t4
t2
t
t4
t1
t2
t
v2
i2 (a)
(b)
Fig. 9.7 Current through and voltage across the inductor of Example 9.2
i (mA) 5
12 0
4
5
7
t (ms)
10
–5
Exercise 9.4. The current in an inductor having inductance L ¼ 10 mH is given by iðtÞ ¼ I0 þ I1 sinð2 p f t þ p=4Þ. Obtain an expression for the voltage induced across the inductor.
Fig. 9.8 See Exercise 9.3
Exercise 9.3. Figure 9.8 shows the current in an inductor having inductance L ¼ 10 mH. Draw a graph of the voltage across the inductor.
Example 9.3. The current in an inductor having inductance L ¼ 1 mH (10–3 H) is given by iðtÞ ¼ I cosð2 p f tÞ, with I ¼ 5 mA and f ¼ 1 kHz. The voltage induced across the inductor is
Example 9.4. In the circuit shown in Fig. 9.9, the switch is moved from a to b at t ¼ 0, having been in position a for t < 0. Obtain expressions for the voltage across the inductor just before the switch is moved (at t ¼ 0 ) and just after the switch is moved (at t ¼ 0þ ). Solution: Because the source is constant and because the switch is in position a for t < 0, the current i is constant and the inductor appears to be a short circuit for t ¼ 0 . The current through the inductor at t ¼ 0 is given by i ¼ V0 =R. For t ¼ 0 , Kirchhoff’s voltage law gives V0 þ vð0 Þ R ¼ 0 ) vð0 Þ ¼ 0:
V0 þ R ið0 Þ þ vð0 Þ ¼ V0 þ R vðtÞ ¼ L
d½I cosð2 p f tÞ ¼ 2 p f LI sinð2 p f tÞ: dt
The maximum (peak) voltage is 2 p f LI ¼ 2 p ð1 kHzÞð1 mHÞð5 mAÞ ffi 31:4 mV. If the frequency is increased to 100 kHz, the voltage increases to 3.14 V, illustrating that the voltage across an inductor is proportional to the rate of change of the current through the inductor.
Because the current in an inductor cannot change instantaneously, the current is the same for t ¼ 0 and t ¼ 0þ . By Kirchhoff’s voltage law, for t ¼ 0þ , V0 þ vð0þ Þ ¼ 0 R ) vð0þ Þ ¼ V0 :
R ið0þ Þ þ vð0þ Þ ¼ R
9.6 Time Constant
307 R
a
v (mV) v
L –
10
+
b
+ V0
5
–
i
4
0
0
Fig. 9.9 See Example 9.4
Equation (9.9) expresses voltage across an inductor in terms of current through the inductor. From (9.9), 1 diðtÞ ¼ vðtÞdt: L
diðt0 Þ ¼ iðtÞ iðt0 Þ ¼
t0
1 L
ðt
ðt
vðt0 Þdt0 :
(9.11)
t0
0; V0 cosð2p f tÞ;
t 0; t > 0;
with V0 ¼ 20 V and f ¼ 400 Hz. The current through the inductor equals zero for t ¼ 0. From (9.11) the current through the inductor is given by ð ð 1 t 0 0 1 t vðt Þdt ¼ V0 cosð2p f t0 Þdt0 iðtÞ ¼ ið0Þ þ L 0 L 0 V0 sinð2p f tÞ ¼ I0 sinð2p f tÞ; ¼ 2p f L where V0 20 V ¼ 2p f L 2pð400 HzÞð100 mHÞ ffi 79:6 mA:
I0 ¼
Fig. 9.10 See Exercise 9.6
Exercise 9.5. The voltage across a 100 mH inductor is given by vðtÞ ¼
t0
Example 9.5. The voltage across a 100 mH inductor is given by vðtÞ ¼
t (μs)
–10
vðt0 Þdt0
or 1 iðtÞ ¼ iðt0 Þ þ L
8
(9.10)
Integrating (9.10) from time t0 to time t gives ðt
12 6
3
0; t 0; V0 et=t ; t > 0:
It also is known that the current through the inductor equals zero for t < 0. Obtain an expression for the current through the inductor.
Exercise 9.6. Figure 9.10 shows a graph of the voltage across a 20 mH inductor. The voltage equals zero for times not shown and the current through the inductor equals zero for t < 0. Draw a graph of the current through the inductor for 0 t 12 ms:
9.6 Time Constant A circuit composed of only resistors and one inductor is called an RL circuit. In this section, we obtain expressions for currents and voltages in an RL circuit subjected to an abrupt change in excitation. Recall that t0 and t0 þ denote times infinitesimally before and after a time t0 . For example, if t ¼ 0 denotes the time at which switch is closed, then t ¼ 0 is the time just before the switch is closed and t ¼ 0þ is the time just after the switch is closed. Refer to Fig. 9.11, where the switch is open for t < 0 and is closed at t ¼ 0. The switch is open for t ¼ 0 , so ið0 Þ ¼ 0. Thus, from (9.11)
308
9 Inductance vR
+
where
– +
R
+
L
V0 –
t¼
vL
i
1 L
ðt 0
vL ðt0 Þdt0 ¼
1 L
ðt 0
vL ðt0 Þdt0
and Kirchhoff’s current law gives, for t > 0 vL ðtÞ V0 1 þ R L
ðt 0
vL ðt0 Þdt0 ¼ 0:
(9.12)
is the time constant for the series RL circuit. The time constant determines how long it takes for the voltage across the inductor to vanish. Because e1 ffi 0:37, the voltage across the inductor drops to 37% of its initial value in a time equal to one time constant. Similarly, e3 ffi 0:05, so the voltage drops to 5% of its initial value in a time equal to three time constants. You can show that the voltage is less than 1% of its initial value when t equals five time constants. From Ohm’s law, iðtÞ ¼
Differentiating (9.12) once with respect to time and rearranging terms gives, for t > 0 L dvL ðtÞ ¼ vL ðtÞ; R dt
(9.13)
According to (9.14), the voltage vL and its derivative have the same mathematical form (are proportional). The function having that property is the exponential function. You can show by substitution that the solution to (9.14) is Rt vL ðtÞ ¼ K exp ; L
t > 0;
(9.14)
v L ð0 Þ V 0 1 þ R L
V0 vL ðtÞ : R
iðtÞ ¼
t i V0 h L 1 exp ; t > 0; t ¼ : R t R
0
v S ðt Þ ¼ vL ðt0 Þdt0 ¼
þ
vL ð0 Þ V0 ¼0 R
þ
(9.19)
Figure 9.12 shows graphs of the voltage vL and the current i, normalized to their maximum values, versus time as a multiple of the time constant. The time constant determines how long it takes for the current through the inductor to reach the steady-state value ið1Þ ¼ V0 =R . In Fig. 9.13, the source is piecewise-constant, switching from one value to another at t ¼ 0 :
ð 0þ
(9.18)
Using (9.16) in (9.18) gives
From (9.12), þ
(9.17)
–
Fig. 9.11 A switched RL series circuit. See (9.12)
iðtÞ ¼ ið0 Þ þ
L R
V1 ; t < 0; V2 ; t 0:
(9.20)
The inductor presents zero resistance to dc. It follows that
) vL ð0 Þ ¼ V0 Thus
ið0þ Þ ¼ ið0 Þ ¼
Rt ; vL ðtÞ ¼ V0 exp L
t>0
(9.21)
(9.15) By Kirchhoff’s voltage law,
Equation (9.15) usually is written t vL ðtÞ ¼ V0 exp ; t
V1 V2 ; ið1Þ ¼ : R R
diðtÞ ¼ V2 dt L diðtÞ V2 þ iðtÞ ¼ ¼ ið1Þ; t > 0 ) R dt R RiðtÞ þ L
t > 0:
(9.16)
(9.22)
9.6 Time Constant
309
Equation (9.23) is applicable not only to the current through an inductor, but to any branch current, in any circuit that is equivalent to the form shown in Fig. 9.13. Also, any node voltage in such a circuit can be expressed as
1
0.8
0.6
t vðtÞ ¼ vð1Þ ½vð1Þ vð0þ Þ exp ; t
0.4
0.2
0 0
1
2
3
4
5
t τ vL(t)
Ri(t)
V0
V0
Fig. 9.12 Inductor voltage and current in the circuit shown in Fig. 9.11 R
Fig. 9.13 An RL series circuit subjected to piecewiseconstant excitation. See (9.20)
vS
+ –
L i
You can show by substitution that (9.22) is satisfied if t iðtÞ ¼ ið1Þ ½ið1Þ ið0þ Þ exp ; t
L : R (9.23)
t¼
It can be shown that (9.23) is the complete solution to the differential equation (9.22). Equation (9.23) can be applied to any circuit that can be reduced to the form shown in Fig. 9.13, where vS(t) is piecewise constant. For example, refer again to the circuit in Fig. 9.11, where the switch is closed at t ¼ 0. By inspection, ið0þ Þ ¼ 0; ið1Þ ¼
V0 L ; t¼ : R R
From (9.23), for t > 0 t V h t i V0 V0 0 iðtÞ ¼ 0 exp ¼ 1 exp ; R R R t t which we obtained by a more circuitous route above (see (9.19)).
L : R (9.24)
t¼
When applying (9.23) or (9.24), be careful to use the correct time constant for the interval of interest and to use ið0þ Þ or vð0þ Þ, not ið0 Þ or vð0 Þ, unless you are describing the current through an inductor, in which case ið0þ Þ ¼ ið0 Þ. Also keep in mind that ið1Þ or vð1Þ denote the eventual value of the current given by (9.23) or the voltage given by (9.24) if (9.23) or (9.24) remain valid for t ! 1. But they are not necessarily the actual end-point values in any interval, because the validity of an instance of (9.23) or (9.24) might be terminated (e.g., by a switching) before the current or voltage reaches ið1Þ or vð1Þ. Example 9.6. Refer to Fig. 9.14, where the switch is open for t < 0 and is closed at t ¼ 0. Obtain expressions for i1 ðtÞ; i2 ðtÞ; iL ðtÞ for t > 0. Solution: We need the circuit time constant and the initial and final values for each current. The The´venin equivalent resistance at the terminals of the inductor is given by RT ¼ R1 kR2 , so the time constant is given by t¼
L ðR1 þ R2 ÞL ¼ : RT R1 R2
(9.25)
Because the switch is open for t < 0, and because the current through an inductor cannot change instantaneously, we know that iL ð0þ Þ ¼ 0 ) i1 ð0þ Þ ¼ i2 ð0þ Þ ¼
V0 : R1 þ R2
Because an inductor presents a short circuit to a constant voltage or current, we know that i L ð1Þ ¼
V0 V0 ; i2 ð1Þ ¼ 0; i1 ð1Þ ¼ iL ð1Þ ¼ : R1 R1
310
9 Inductance R1
iL
iL
+ +
V0
R2
L
I0
R
R
L
–
i1
vL –
i2
Fig. 9.15 See Exercise 9.9 Fig. 9.14 See Example 9.6
We may now use (9.23) to obtain the requested expressions: t i1 ðtÞ ¼ i1 ð1Þ ½i1 ð1Þ i1 ð0þ Þ exp t t V0 V0 V0 ¼ exp ; R1 R1 R1 þ R2 t t i2 ðtÞ ¼ i2 ð1Þ ½i2 ð1Þ i2 ð0þ Þ exp t t V0 exp ; ¼ R 1 þ R2 t t iL ðtÞ ¼ iL ð1Þ ½iL ð1Þ iL ð0þ Þ exp t t i V0 h 1 exp ¼ : R1 t In all cases, the time constant t is given by (9.25) and the expression is valid for t > 0.
Exercise 9.7. Show that the currents (expressions) obtained in Example 9.6 satisfy Kirchhoff’s current law.
Obtain expressions for the current iL and the voltage vL.
Example 9.7. Refer to Fig. 9.16. The source voltage vS ðtÞ equals zero for times not shown. Obtain an expression for the voltage across the inductor for t > 0. Solution: One approach is to obtain an expression for the current i(t) and subsequently use vL ðtÞ ¼ vS ðtÞ RiðtÞ: The time constant is t¼
For t < 0, the source appears as a short circuit, so ið0þ Þ ¼ ið0 Þ ¼ 0. For 0 < t t1 , the current increases toward i1 ð1Þ ¼
Exercise 9.8. Use the expression for iL ðtÞ obtained in Example 9.6 to obtain an expression for the voltage across the inductor. Then use that expression and the source voltage to obtain expressions for the currents i1 ðtÞ; i2 ðtÞ. Show that these expressions for i1 ðtÞ; i2 ðtÞ agree with those obtained in Example 9.6.
Exercise 9.9. Refer to Fig. 9.15. The switch is closed for t < 0 and opened at t ¼ 0.
L ¼ 1 ms: R
V1 ¼ 10 mA; R
where the subscript on i1 indicates that the relation holds for the first segment of the response. From the relations above and (9.23), we have t i1 ðtÞ ¼ i1 ð1Þ ½i1 ð1Þ i1 ð0þ Þ exp t
t V1 V1 0 exp ¼ R R t h i V1 t ¼ 1 exp ; R t L t ¼ ; 0 < t t1 : R
9.6 Time Constant
311 vS
R + vS
+ –
L i
V1
vL
V2 0
–
t 0
t1
t2
R = 1kΩ, L = 1mH, V1 = 10V, V2 = 5V, t1 = 2μs, t2 = 4μs
Fig. 9.16 See Example 9.7
The final value of the first segment becomes the initial value for the second segment, because the current through an inductor is continuous. Thus, if we reset the time origin to t1, t i V1 h 1 i2 ð0þ Þ ¼ i1 ðt1 Þ ¼ 1 exp R t ¼ ð10 mAÞ½1 expð2Þ ffi 8:65 mA
We use these values in (9.23) and translate the resulting segment to t2. Thus tt 2 i3 ðtÞ ¼i3 ð1Þ ½i3 ð1Þ i3 ð0þ Þ exp t tt 1 ¼0 ½0 i2 ðt2 Þ exp t tt 2 ¼ i2 ðt2 Þ exp ; t > t2 : t Thus 8 9 0; t<0; > > > > > < i ðtÞ; 0 = 1 1 iðtÞ ¼ > i2 ðtÞ; t1 > > > > : ; i3 ðtÞ; t > t2 : ) vL ðtÞ ¼ vS ðtÞ RiðtÞ 8 9 0; t < 0; > > > > > < V Ri ðtÞ; 0 = 1 1 1 ¼ > V2 Ri2 ðtÞ; t1 > > > > : ; t>t2 ; Ri3 ðtÞ; 8 9 0; t < 0; > > > > > > > > t > > > > ; 0< t t V exp ; 1 1 > > < = t ¼ t t1 > ; t1 < t t2 ; > ½V Ri1 ðt1 Þexp > > > 2 > t > > > > > > t t > > 2 : Ri2 ðt2 Þexp ; t > t2 : ; t
and i2 ð1Þ ¼
V2 ¼ 5 mA: R
We use these values in (9.23) and translate the resulting segment to t1. Thus tt 1 i2 ðtÞ ¼ i2 ð1Þ ½i2 ð1Þ i2 ð0þ Þ exp t
tt V2 V2 1 ¼ i1 ðt1 Þ exp ; R R t t1 < t t2 :
Figure 9.17 shows a graph of the voltage vL ðtÞ versus time.
The final value of the second segment becomes the initial value for the third segment, because the current through an inductor is continuous. Thus, i3 ð0þ Þ ¼ i2 ðt2 Þ
t t V2 V2 2 1 ¼ i1 ðt1 Þ exp R R t ffi 5mA ½5mA 8:65mAexpð2Þ ffi 4:73mA
10 8 6 4 2
vL (V)
0 –2 –4 –6 –8 –10
and
0
1
2
3
4
5
6
7
8
9
10
t (μs)
i3 ð1Þ ¼ 0:
Fig. 9.17 Load voltage in the circuit in Fig. 9.16. See Example 9.7
312
9 Inductance
9.7 Inductors in Series and Parallel
1 1 1 1 ¼ þ þ
þ : Leq L1 L2 LN
In this section, we assume that coils connected in series or in parallel are connected in such a way that there are no magnetic flux linkages between the coils. Section 9.12 treats magnetically coupled coils. Refer to Fig. 9.18. By Kirchhoff’s voltage law, di di di þ L 2 þ þ LN dt dt dt di ¼ ðL1 þ L2 þ þ LN Þ : dt
v ¼ L1
(9.26)
Therefore a series connection of inductors is equivalent (at the terminals) to one inductor having inductance Leq given by Leq ¼ L1 þ L2 þ þ LN :
(9.27)
(9.29)
Equations (9.27) and (9.29) assume that none of the flux produced by any one of the inductors links any of the other inductors; that is, that there is no mutual inductance between the coils. This assumption is invalid, as are (9.27) and (9.29), if the coils comprising the inductors are close enough together that magnetic coupling is significant. Equation (9.29) ignores the winding resistances of the individual inductors, which might not be a bad approximation at low frequencies, for inductors having small dc resistances. Equations (9.27) and (9.29) are rarely useful in practice. It might happen occasionally that certain approximations lead to a circuit model in which two inductors appear in series or parallel, in which case (9.27) or (9.29) allow further simplification. But (9.27) and (9.29) rarely arise in design because one would never specify two or more inductors where one would do. An exception might be where a very accurate and precise inductance is needed, in which case one might use a fixed inductance in series with a smaller, adjustable inductance.
Refer to Fig. 9.19. By Kirchhoff’s current law, ð ð ð 1 t 1 t 1 t vðtÞdt þ vðtÞdt þ
þ vðtÞdt L1 L2 1 LN 1 1 ðt 1 1 1 ¼ þ þ
þ vðtÞdt: L1 L2 LN 1 (9.28)
i¼
Therefore a parallel connection of inductors is equivalent (at the terminals) to one inductor having inductance Leq given by
i
+
L1
L2
i
Leq
= v –
v
1 1 1 L2 L3 ¼ þ ) L23 ¼ : L2 þ L 3 L23 L2 L3
Leq ¼ L1 þ L23 ¼ L1 þ
Fig. 9.18 Inductors in series
L2 L3 : L2 þ L3
i
i +
v
Solution: From (9.29), the equivalent inductance of the parallel inductors L2 ; L3 is given by
From (9.27), the equivalent inductance of the circuit at the specified terminals is given by
+
–
Example 9.8. Obtain an expression for the equivalent inductance at the terminals a-b of the circuit shown in Fig. 9.20. Assume the magnetic fields produced by the inductors do not overlap.
+ L1
L2
+
Fig. 9.19 Inductors in parallel
LN = v –
Leq
Exercise 9.10. Obtain an expression for the equivalent inductance at the terminals a–b of
9.8 Energy Storage and Power dissipation in an Inductor
a
+ L2
v b
where i(t) is the instantaneous current through the inductor. For economy, the instantaneous energy stored in the magnetic field produced by an inductor usually is referred to as the energy stored by (or in) the inductor. The energy stored in the magnetic field produced by a current makes the current resistant to change, because it takes time to transfer energy from the current to the magnetic field or vice-versa. In other words, the magnetic field created by a current gives the current a kind of inertia that resists changes in the current. An inductor enhances this effect by concentrating and intensifying the magnetic field produced by a current through the inductor.
L1
i
L3
–
Fig. 9.20 See Example 9.8
L
a
2L
L
2L
313
L
b
Fig. 9.21 See Exercise 9.10
the circuit shown in Fig. 9.21. Assume the magnetic fields produced by the inductors do not overlap.
Exercise 9.11. The current in an inductor having inductance L ¼ 1 mH is given by iðtÞ ¼ I cosð2 p f tÞ, with I ¼ 5 mA and f ¼ 1 kHz. Express the instantaneous energy stored in the inductor as a function of time. The average power dissipated in an inductor over a finite time interval t0 t < t0 þ T is given by
9.8 Energy Storage and Power dissipation in an Inductor
1 ½eðt0 þ T Þ eðt0 Þ T
1 1 2 1 L i ðt0 þ T Þ L i2 ðt0 Þ : ¼ T 2 2
PT ¼ The instantaneous power dissipated in an inductor having inductance L is given by p ¼ vi ¼ L
di dw i¼ ; dt dt
(9.30)
where i(t) is the instantaneous current through the inductor and wðtÞ is the instantaneous energy stored in the magnetic field produced by the current. We have from (9.30) that dw ¼ L i di, which implies ð 1 wðtÞ ¼ L i di ¼ Li2 ðtÞ þ B 2 where B is a constant of integration. From (9.4), magnetic flux is proportional to current, so if i(t) ¼ 0, the flux equals zero, the magnetic field strength equals zero, and the stored energy w(t) equals zero. Thus B ¼ 0 and the instantaneous energy stored in the magnetic field produced by an inductor is given by 1 wðtÞ ¼ L i2 ðtÞ; 2
(9.31)
(9.32)
We assume the stored energy (or, equivalently, the current through the inductor) is finite always. Thus the terms in the brackets on the right side of (9.32) are finite. It follows that the average power dissipated in an inductor equals zero: P ¼ lim ðPT Þ ¼ 0: T!1
The instantaneous power dissipated in an inductor is not zero, nor is the peak power. An inductor can absorb energy at some times and return energy to a circuit at other times. None of the energy absorbed (by an ideal inductor) is lost to the circuit, but can be returned on demand. This is in contrast to a resistor, which converts electrical energy to heat energy that is then lost forever to the circuit. On an instantaneous basis, an inductor behaves sometimes like a sink and other times like a source, but on average (over a sufficiently long time), is neither.
314
9 Inductance a
Example 9.9. Find the average powers dissipated in the resistor and the source in the circuit shown in Fig. 9.22, where R ¼ 2 kO and iðtÞ ¼ I0 cosð2 p f tÞ;
R
I0 ¼ 10 mA:
L
vL
iL
Fig. 9.24 See Exercise 9.13
Solution: Because the average power dissipated in the inductor equals zero, and because power is conserved, the sum of the powers dissipated in the resistor and the source equals zero. The power dissipated in the resistor is PR ¼ irms 2 R ¼
+
b I0
–
after the switch is moved from a to b? What is the current iL through the inductor at that time?
9.9 Parasitic Self-Inductance
I0 2 R ¼ 100 mW 2
Self-inductance is present wherever current exists, whether we like it or not. Parasitic self-inductance refers to unintentional and generally undesirable inductance that is present in components other than inductors, such as conductors, resistors, and capacitors. In the simplest cases, parasitic self-inductance is due largely to current in the leads of such components and in conductors (wires) that interconnect devices. Numerous formulas have been presented for the self inductance of a straight, isolated, non-magnetic wire.7 One of these is
and the power dissipated in the source is Pi ¼ PR ¼ 100 mW:
Exercise 9.12. Refer to Fig. 9.23. What is the voltage vL across the inductor a very long time after the switch is moved from a to b? What is the current iL through the inductor at that time?
m0 l 4l 1 ; ln L¼ 2p d
m0 ¼ 4p 109 H cm1 ; (9.33)
Exercise 9.13. Refer to Fig. 9.24. What is the voltage vL across the inductor a very long time
R i
L
Fig. 9.22 See Example 9.9
a R V0
+ –
where the length l of the wire is much larger than the diameter d. Figure 9.25 shows a graph of inductance in nH versus wire length in cm for 1 cm l 10 cm, calculated from (9.33). Also shown (dotted line) is a linear approximation to (9.33) for that range of wire length. The slope of the linear approximation is approximately 12 nH cm1 , which implies that the selfinductance of an isolated straight conductor is about 12 nH cm1 . Inductances calculated using (9.33) might be a bit high, as other methods yield lower values. But in design, it usually is best to be conservative.
+
b iL
L
vL – 7
Fig. 9.23 See Exercise 9.12
Grover, F.W., Inductance Calculations, Dover, New York, 2004.
9.9 Parasitic Self-Inductance
315
ment above, the self-inductance of a 1-cm wire is on the order of ð12 nH cm1 Þ ð1 cmÞ ¼ 12 nH. The associated self-induced voltage for a sinusoidal current through the wire is given by
150
100 L (nH)
di d ¼ L ½I0 cosð2 p f tÞ dt dt ¼ 2 p f L I0 sinð2 p f tÞ:
v¼L 50
0
0
1
2
3
4
5 6 l (cm)
Eq. (9.29)
7
8
9
10
The peak amplitude of the self-induced voltage equals 1 mV (is comparable to voltages of interest) if (9.36)
1 mV ffi 13:3 MHz: ð2 pÞ ð12 nHÞ ð1 mAÞ
(9.37)
which implies f ¼
In many cases, lumped-constant models fail before self-inductance of conductors becomes significant. Lumped-constant models are valid only for circuits whose dimensions are much larger than the wavelengths of currents and voltages involved. The wavelength l of a sinusoidal current or voltage (in air) having frequency f is given by c l¼ ; f 1
(9.34)
where c ffi 3 10 m s is the speed of light. For example, the wavelength of a 1 GHz sinusoid is 30 cm, so ordinary lumped-constant models can be applied to centimeter-size circuits operating at frequencies of 1 GHz or below, but probably cannot be applied to such circuits at frequencies of 10 GHz (wavelengths of 3 cm) or to circuits in which the lengths of conductors approach 30 cm. For example, although the graph in Fig. 9.25 indicates that a 5-cm conductor has a self-inductance of 50 nH, that fact is meaningless at frequencies higher than 1 GHz or so, because a wavelength of 5 cm corresponds to a frequency of 6 GHz. Where a lumped-constant model is valid, selfinductances are significant if the associated currents and voltages are significant relative to currents and voltages of interest. For example, consider a circuit whose dimensions are on the order of 1 cm and in which currents and voltages of interest are on the order of 1 mA and 1 mV, respectively. From the develop8
2 p f L I0 ¼ 1 mV;
Linear Approx.
Fig. 9.25 Self-inductance of a straight wire as a function of wire length
(9.35)
The self-induced voltage along a 1-cm straight wire carrying a 1-mA sinusoidal current is less than 1 mV until the frequency of the current approaches 13 MHz. At that frequency and for that current, a lumped-constant ðR; L; CÞ model remains valid for a centimetersize circuit, because the wavelength of a 13 MHz current or voltage is c 3 108 ffi 23 m; l¼ ¼ f 13 106
(9.38)
which is very much larger than 1 cm. Thus in this case, self-inductance is both meaningful and significant. Exercise 9.14. A sinusoidal current having frequency f and peak amplitude I passes through an axial-lead resistor having resistance R and series self-inductance L. Assuming a lumped-constant model is applicable, obtain an expression for the frequency at which the rms voltage drop across the self-inductance equals 1% of the rms voltage drop across the resistance. Inductors are used in basically three ways: • In series with a load, to suppress ripple or highfrequency noise;
316
9 Inductance
• As components of circuit models for physical devices;. e.g., electric motors, generators, and transformers; • In conjunction with capacitors, to construct frequency-selective circuits (filters). We are as yet unprepared to treat circuits containing both inductors and capacitors. But we can describe how an inductor alone can be used to reduce ripple (or undesirable high-frequency noise) accompanying a desirable current or voltage.
ponent of the source voltage is sinusoidal. The required trigonometric and algebraic manipulations are simplest if we assume the initial phase of the ac component of the current i equals zero, such that i ¼ Idc þ Iac cosðo0 tÞ:
(9.41)
It follows that the load voltage is given by vR ¼ RIdc þ RIac cosðo0 tÞ ¼ VR dc þ VR ac cosðo0 tÞ and that the source voltage is given by an expression of the form
9.10 Reducing Ripple
vS ¼ VS dc þ VS ac cosðo0 t þ yÞ:
Recall that in some applications where the dc component Vdc of a voltage is the desirable component and the ac component vac is undesirable, the ripple factor, defined as g¼
Vac rms jVdc j
(9.39)
is a useful figure of merit. Like capacitors, inductors can be used to reduce ac ripple in a resistive load. When used for this purpose, an inductor is called a choke. Whereas a bypass capacitor is connected in parallel with a load, a choke is connected in series with a load, as shown in Fig. 9.26, where the source vS consists of a desirable dc component VS dc and an undesirable ac component (ripple) vS ac ðtÞ. If the choke is absent (is replaced by a conductor), the load voltage vR equals the source voltage vS and the ripple factor is given by g0 ¼
VS ac rms : jVS dc j
(9.40)
Below, we obtain an expression for the ripple factor with the inductor present. We assume the ac com-
Superposition allows us to find the responses to the dc and ac component of the source individually. Because an inductor acts as a short circuit for dc, the dc component of the load voltage (the voltage across the resistor) equals the dc component of the source voltage. Thus VR dc ¼ VS dc :
vLac þ vR ac ¼ vS ac ) L
diac þ Riac ¼ VS ac cosðo0 t þ yÞ: dt
From (9.41), iac ¼ Iac cosðo0 tÞ. Thus Lo0 Iac sinðo0 tÞ þ RIac cosðo0 tÞ ¼ VS ac cosðo0 t þ yÞ ¼ VS ac ½cosðo0 tÞ cosðyÞ sinðo0 tÞ sinðyÞ; which holds for all time only if the coefficients of cosðo0 tÞ and sinðo0 tÞ on the left side equal the corresponding coefficients on the right side. Thus we obtain two equations
Fig. 9.26 Use of an inductive choke to reduce ripple
vS
+ R
i
Lo0 Iac ¼ VS ac sinðyÞ;
–
L
+ –
(9.43)
The ac components of the voltages involved satisfy Kirchhoff’s voltage law. Thus
RIac ¼ VS ac cosðyÞ; vL
+
(9.42)
vR –
which yield ðRIac Þ2 þðLo0 Iac Þ2 ¼ ðVS ac Þ2 :
(9.44)
9.10 Reducing Ripple
317
The ac component of the load voltage vR is given by Example 9.10. In Fig. 9.26, R ¼ 2 O and vS ¼ Vdc þ Vac cosðo0 t þ yÞ with Vdc ¼ 100 V, pffiffiffi Vac ¼ 25 2 V, and f0 ¼ 120 Hz. The required ripple factor is 0.1% (0.001). Specify the inductance L.
VR ac ¼ RIac ; so (9.44) becomes ðVR ac Þ2 þ
Lo0 VR ac R
2 ¼ ðVS ac Þ2 ;
Solution: From (9.49) pffiffiffi Vac 25 2 V pffiffiffi ¼ 0:25; g0 ¼ pffiffiffi ¼ Vdc 2 100 2 V ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi s ffi R g0 2 L¼ 1 g o0 ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi s 2O 0:25 2 ¼ 1 ¼ 663 mH: 240p s1 0:001
which reduces to jVS ac j jVR ac j ¼ pffiffiffiffiffiffiffiffiffiffiffiffiffiffi ; 1 þ Q2 where we have defined Q¼
o0 L : R
(9.45)
We could have simplified the calculation somewhat by using (9.50), because
The ripple factor is given by VRac 1 jVac j g0 pffiffiffi pffiffiffiffiffiffiffiffiffiffiffiffiffiffi ¼ pffiffiffiffiffiffiffiffiffiffiffiffiffiffi ; g ¼ pffiffiffi ¼ Vdc 2 jVdc j 2 1 þ Q2 1 þ Q2 (9.46)
g0 0:25 ¼ ¼ 250 1: g 0:001 Thus Lffi
where, from (9.40) Vac g0 ¼ pffiffiffi: V 2
(9.47)
Rg0 ð2 OÞð0:25Þ ¼ ¼ 663 mH: o0 g ð240p s1 Þð0:001Þ
as before.
dc
Conversely, the inductance L required to attain a specified ripple factor g is found as follows: From (9.46), o0 L ¼ Q¼ R
sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2 ffi g0 1; g
(9.48)
whence R L¼ o0
sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2 ffi g0 1; g
Vac g0 ¼ pffiffiffi: V 2
(9.49)
dc
In many applications, g0 =g 1, in which case Lffi
Rg0 ; o0 g
g0 g:
(9.50)
Exercise 9.15. The dc output of a certain power supply is 12 V. For a 4 O resistive load, the ripple factor of the load voltage is g ¼ 104 . (a) What is the rms amplitude of the ac component of the load voltage? (b) Assuming the ripple is a 120 Hz sinusoid, what is the ripple factor for the load voltage if a 200 mH inductor is connected in series with the load? Another approach is to require that the ac component of the load voltage be a small fraction of the ac component of the source voltage, which is equivalent to requiring that the ac component of the inductor voltage be much larger than the ac component of the load voltage, which requires
318
9 Inductance
diac L dt jRiac j:
(9.51)
Using (9.41) in (9.51) gives jo0 LIac j jRIac j )
o0 L ¼ Q 1; R
(9.52)
which implies that requiring a large fraction of the total ac voltage to appear across the inductor is equivalent to requiring that Q¼
o0 L 1: R
(9.53)
and the load, whereas the total ripple voltage across the series connection of a choke and load is not reduced by the choke. For example, suppose we wish to reduce the ac component of the voltage between two nodes a, b connected by a resistor. Connecting a capacitor in parallel with the resistor will reduce the ac component of vab , but connecting an inductor in series with the resistor will not. Keep in mind that the analysis above assumes sinusoidal ripple, as given by (9.42). If the ac component of the source vS in Fig. 9.26 is not sinusoidal, then the ac components of the source voltage and load voltage have different waveforms.8 In that case, analysis of the load ripple is much more complicated and beyond the scope of this book.
Also, from (9.46), if Q is large, g0 pffiffiffiffiffiffiffiffiffiffiffiffiffiffi2 ¼ 1 þ Q ffi Q; Q 1; g
9.11 Inductive Kick
or g¼
g0 ; Q 1: Q
(9.54)
R g0 o0 g
(9.55)
which yields L¼
as before. Equations (9.50) and (9.55) are good approximations to (9.49) (less than about 1% error) if g0 =g > 7, which is usually true in applications. Exercise 9.16. The voltage across a 2 O resistive load is given by
Current through an inductor cannot change instantaneously. Because voltage across the terminals of an inductor is proportional to the time derivative of current through the inductor, the terminal voltage becomes as large as necessary to prevent an instantaneous change in current. For example, consider the situation illustrated by Fig. 9.27, where a switch attempts to interrupt the current through an inductor. When the switch is suddenly opened, a very large voltage can appear across the switch, leading to arcing and (sooner or later) failure of the switch. Such a high voltage in a switched inductive circuit is called inductive kick.9 Inductive kick is a useful phenomenon in certain applications, such as automobile ignition systems, where the large voltage applied to the spark
v ¼ Vdc þ Vac cosð2 p f tÞ; with f ¼ 10 kHz, Vdc ¼ 5 V, and Vac ¼ 500 mV. Specify a series choke such that the load ripple is reduced by a factor of 1000.
+
Fig. 9.27 Switching arc caused by inductive kick
8
Using a series choke to reduce the ripple in a load voltage or current is not always an alternative to bypassing the load with a capacitor. A bypass capacitor reduces the voltage ripple across both the capacitor
V0
–
L
For example, if the current through an inductor has a triangular waveform, then the voltage across the inductor has a rectangular (piecewise-constant) waveform. 9 This terminology is borrowed from Paul Horowitz and Winfield Hill, The Art of Electronics, (2nd Ed.), Cambridge University Press, New York, 1980.
9.12 Magnetically Coupled Coils and Mutual Inductance
plugs is obtained by interrupting the current through the primary of a transformer,10 and in some highvoltage power supplies, where high voltages are produced in essentially the same manner. But in many cases, inductive kick is undesirable and potentially destructive. Special measures often are necessary to protect switching apparatus and other components when switching large inductive loads such as transformers and electric motors. Such measures take various forms, ranging from none for small inductive loads carrying small currents to elaborate measures for large inductive loads carrying large currents. For example, if the inductance in Fig. 9.27 is very small, perhaps a sufficiently robust switch is all that is necessary. But if the inductance is large, additional provisions are necessary. One such provision for a dc motor is to shunt the switch with a diode, as illustrated by Fig. 9.28. The diode allows energy stored in the inductor to dissipate in the forward resistance of the diode and in the resistance of the motor windings. This method does not work for an ac motor, because in that case, the diode would shunt every other half cycle and useable power to the motor would be greatly reduced.11 Figure 9.29 shows a protection method sometimes employed for ac motors. The resistor is large enough that only a small fraction of the total current is diverted
+ V0 –
dc motor
Fig. 9.28 A diode as an arc suppressor
R
+
v(t) –
C
ac motor
Fig. 9.29 An RC (snubber) circuit as an arc suppressor
10
The ignition coil in an automobile is actually a transformer. In fact, the motor might not even run, unless it is a universal or ac/dc motor.
11
319
from the motor while it is running. But when the switch is opened, the current through the inductor is diverted to the RC branch, and energy is stored in the capacitor for subsequent dissipation in the resistor and the resistance of the motor windings. Thus the electrical energy stored in the magnetic field of the motor and the mechanical energy stored in the load, which otherwise would be dissipated in an arc at the switch, is dissipated instead as heat by the resistor. For small to medium (1/10–5 hp) motors, the resistance R is typically about 20200 O and the capacitance C is typically about 0:010:1 mF. The RC protective circuit shown in Fig. 9.29 is called a snubber. More complex snubber circuits can more effectively convert the mechanical energy stored in a rotating machine to heat dissipation in a resistor, allowing faster decreases in motor speed. Analysis of such circuits is best done using methods treated in subsequent chapters.
9.12 Magnetically Coupled Coils and Mutual Inductance Faraday’s law of induction states that a change in magnetic flux linking a conductor induces a voltage in the conductor, regardless of the source of the flux. A magnetic field produced by a changing current in one conductor can induce a voltage in a neighboring conductor. That is, if changing flux arising from changing current in one conductor links a second conductor, then voltage will be induced in the second conductor. The polarity of the induced voltage is such that any current produced by the voltage will attempt to keep the flux from changing. Two conductors (or coils, or circuits) linked in this way are said to be magnetically coupled and induction of a voltage in one conductor by changing current in another is called mutual inductance. We begin by obtaining a circuit model for magnetically coupled coils. We refer to Fig. 9.30, where the resistances R1 ; R2 represent the resistance of the wire forming the coils. The currents i1 ; i2 produce magnetic flux, where: f11 is the flux produced by the current i1 that links only coil 1 f12 is the flux produced by the current i1 that links both coils
320
9 Inductance i1 +
R1
i2 f12
+ f11
Fig. 9.30 Magnetically coupled coils
vA
v1
–
–
The total flux f1 produced by the current through coil 1 and the total flux f2 produced by the current through coil 2 are given by f1 ¼ f11 þ f12 ;
f2 ¼ f22 þ f21 :
(9.56)
Actually, not all of the flux produced by the current through a coil links every turn of the coil. The fluxes defined above are effective fluxes that account for that fact. For example, the flux f11 is an effective flux which, if linked with all the turns of coil 1, gives the correct total number of flux linkages. We assume the coils are wound such that the total flux produced by a current is proportional to the current.12 Thus the total flux produced by each coil is proportional to the current through the coil. A fraction k of the flux produced by coil 1 links with coil 2 and (by symmetry) the same fraction the flux produced by coil 2 links with coil 1. We have f12 ¼ kf1 ¼ kaN1 i1
+
v2
vB
–
–
N2 turns
From (9.57) and (9.58), k¼
f12 f21 ¼ : f1 f2
(9.59)
The parameter k is the coupling coefficient for the coils because the fractions f12 =f1 and f21 =f2 indicate the degree of coupling between two coils. That is, how much of the flux produced by one coil links the other coil. The maximum possible value of each fraction is unity. We are dealing with currents through and voltages across coils, so we seek an inductive model relating the currents and voltages in Fig. 9.30. With reference to (9.4), the self-inductances L1 ; L2 of the coils are given by L1 ¼
N1 f1 L 1 i1 ) f1 ¼ ; i1 N1
L2 ¼
N2 f2 L2 i2 ) f2 ¼ : i2 N2 (9.60)
By analogy, we define the mutual inductances M21 ; M12 as
(9.57)
N1 f21 M21 i2 ) f21 ¼ ; i2 N1 N2 f12 M12 i1 ¼ ) f12 ¼ : i1 N2
M21 ¼
and f2 ¼ aN2 i2 ;
f21 ¼ kf2 ¼ kaN2 i2 ;
(9.58)
where a depends upon the coil geometry and core material, but not on the current or flux.
12
R2
f 22
N1 turns
f22 is the flux produced by the current i2 that links only coil 2, and f21 is the flux produced by the current i2 that links both coils.
f1 ¼ aN1 i1 ;
+ f 21
This is equivalent to assuming that the permeability of the core material is constant and independent of position.
M12
(9.61)
Using the right sides of (9.57) and (9.58) in (9.61) yields M21 ¼ ka N1 N2 ; M12 ¼ ka N1 N2 ) M12 ¼ M21 ¼ M:
(9.62)
9.12 Magnetically Coupled Coils and Mutual Inductance
From (9.60), (9.61), and (9.62), we obtain L2 L2 ¼
N2 f2 N1 f1 ; i2 i1
M12 M21
N2 f12 N1 f21 M2 f f ¼M ¼ ) ¼ 12 21 : i1 i2 L 2 L2 f2 f1
321 i1
f1
i1
i2
f2
i2
f1
2
f2
It follows from this result and (9.59) that the coupling coefficient is given by sffiffiffiffiffiffiffiffiffiffi M2 j Mj ¼ pffiffiffiffiffiffiffiffiffiffi : k¼ L2 L2 L2 L2
(9.63)
Conventionally, as used in circuit equations, mutual inductance is positive, so the absolute-value sign in (9.63) is unnecessary. This remark is explained more fully in the sequel. Using (9.62), the right side of (9.61) can be written
(a)
Fig. 9.31 The sign of the mutual terms in (9.67) is (a) positive or (b) negative, depending upon how the coils are wound and the directions of the currents in the coils i1
i1
+
+
v1
f21
(9.64)
l1 ¼ N1 ðf1 f21 Þ; l2 ¼ N2 ðf2 f12 Þ:
M
L1 i1 Mi2 ¼ L1 i1 Mi2 ; N1 N1 L2 i2 Mi1 ¼ L2 i2 Mi1 ; l2 ¼ N2 N2 N2
l1 ¼ N1
(9.66)
where M 0. By Faraday’s law, the voltages across the coils are given by dl1 di1 di2 ¼ L1 M ; dt dt dt dl2 di2 di1 ¼ L2 M : v2 ¼ dt dt dt
L2
v1 ¼
(9.67)
To know whether to use the positive or negative signs on the mutual terms in (9.67), we must know whether the fluxes produced by i1 and i2 are in the same or
v2
L2
– (a)
where the positive sign applies if the fluxes produced by each current are in the same direction (as shown in Fig. 9.30) and the negative sign applies otherwise. Using (9.60) and (9.64) in (9.65) gives
M
i2 +
+ –
(9.65)
L1
–
v2
The total flux linkages for the two coils are
v1
L1
– i2
Mi2 Mi1 ¼ ; f12 ¼ : N1 N2
(b)
(b)
Fig. 9.32 Dot-convention labeling for the coils in Fig. 9.31
opposite directions. If the fluxes are in the same direction, we must use the positive sign. If the fluxes are in opposite directions, we must use the negative sign. If we know how the coils are wound – e.g., if we are presented with a picture like the one shown in Fig. 9.31 – we can determine which sign should be used. If the current directions and coil windings are as shown in Fig. 9.31(a), we would use the positive sign. If the current directions and coil windings are as shown in Fig. 9.31(b), we would use the negative sign. But it is impractical to require such detailed representations of coils in circuit diagrams, so we use instead a convention called the dot convention, where dots are used to indicate corresponding ends of coupled coils. If the positive directions of the currents are either both into or both out of corresponding ends, we must use the positive sign. Otherwise, we must use the negative sign. Figure 9.32 shows how the dot convention can be used to indicate the corresponding ends of the coils drawn in Fig. 9.31. For the arrangement in Fig. 9.32(a), which corresponds to Fig. 9.31(a), we would write
322
9 Inductance i
a
i
+
+
v –
L1
M
L2
which, when written out, becomes
Leq ⇒ v
L1 i1
(a)
di1 L2 M ¼ v; dt L 1 L2 M 2 di2 L1 M i02 ¼ ¼ v; dt L 1 L2 M 2
i01 ¼
i2
–
b
M
L2
(b)
Fig. 9.33 See Example 9.11
whence v1 ¼ L1
di1 di2 þM ; dt dt
v 2 ¼ L2
di2 di1 þM ; dt dt
whereas for the arrangement in Fig. 9.32(b), which corresponds to Fig. 9.31(b), we would write v1 ¼ L1
di1 di2 M ; dt dt
v2 ¼ L2
di2 di1 M : dt dt
di1 di2 d ði1 þ i2 Þ di L2 þ L1 2M þ ¼ ¼ ¼ v; dt dt dt dt L 1 L2 M 2 which yields v¼
L1 L2 M 2 di : L2 þ L1 2M dt
This last relation has the form Example 9.11. Obtain the equivalent inductance at the terminals a–b of the circuit shown in Fig. 9.33(a). Solution: We re-draw the circuit to obtain the circuit diagram in Fig. 9.33(b), which defines the loop currents such that each enters the dotted terminal of the associated coil. Applying Kirchhoff’s voltage law to each of the indicated loops gives di1 di2 þM ; dt dt di2 di1 þM ; v ¼ L2 dt dt
(9.68)
where we use the positive sign on the mutual term because both currents enter dotted terminals. We can write (9.68) in vector-matrix form as L1 M
M L2
"
i01 i02
#
" # v ¼ ; v
(9.69)
di ; dt
where the equivalent inductance Leq is given by Leq ¼
L 1 L2 M 2 : L1 þ L2 2M
From (9.63), M¼
v ¼ L1
v ¼ Leq
pffiffiffiffiffiffiffiffiffiffi L1 L2 ) k ¼ 1:
(9.70)
Coils for which the coupling coefficient is near unity are said to be tightly coupled. Tight coupling between coils can only be achieved if the coils are wound on a common magnetic core. Exercise 9.17. Refer to (9.68). Show that if the coupling coefficient equals unity, then rffiffiffiffiffi L2 v1 ; k ¼ 1: v2 ¼ (9.71) L1
where i01 ¼ di1 =dt; i02 ¼ di2 =dt. The solution is 0
1
v i1 L1 M v L2 M ¼ ; ¼ i02 M L2 v L 1 L2 M 2 L 1 M
Exercise 9.18. The solution given in Example 9.11 is invalid if the coupling coefficient pffiffiffiffiffiffiffiffiffiffi is unity, because if k ¼ 1, then M ¼ L1 L2 and
9.13 Parasitic Mutual Inductance
323
the matrix on the left in (9.69) is singular. ffi pffiffiffiffiffiffiffiffiffi (a) Show that if M ¼ L1 L2 then v ¼ 0 and
Thus the total flux produced by current i1 equals f1 ¼ f11 þ f12 , the total flux produced by current i2 equals f2 ¼ f22 þ f21 , and the self-inductances (per unit length) of the individual conductors are given by
pffiffiffiffiffi di2 pffiffiffiffiffi di1 ¼ L1 : L2 dt dt
f1 ¼ L1 i1 ;
pffiffiffiffiffi pffiffiffiffiffi (b) Does this mean that i2 L2 ¼ i1 L1 ? Explain.
f 2 ¼ L 2 i2 :
(9.73)
Similarly, the flux f12 produced by current i1 that links conductor 2 and the flux f21 produced by current i2 that links conductor 1 give rise to mutual inductances given by f12 ¼ M12 i1 ;
9.13 Parasitic Mutual Inductance
f21 ¼ M21 i2 :
(9.74)
By symmetry, Parasitic mutual inductance between two long, straight, non-magnetic, identical wires depends upon wire spacing and pair geometry (e.g., parallel or twisted), but does not exceed the self inductance of either wire. Refer to Fig. 9.34, which shows an end view of two neighboring conductors carrying current into the page. We identify four components of the total flux (per unit length of the conductors): f11 ¼ flux produced by current i1 that links only conductor 1 f12 ¼ flux produced by current i1 f22
that links both conductors ¼ flux produced by current i2 that links only conductor 2
f21 ¼ flux produced by current i2 that links both conductors
f11
f 22
i1
i2
(9.72)
f 21
M12 ¼ M21 ¼ M:
(9.75)
The induced voltages in the conductors are given by di1 di2 M ; dt dt di2 di1 M ; v2 ¼ L2 dt dt v1 ¼ L1
(9.76)
where the positive sign is used if the currents are in the same direction, as assumed in Fig. 9.34, and negative if the currents are in opposite directions. In other words, if the fluxes produced by the conductors are in the same direction (both clockwise or both counterclockwise), then the self-induced and mutuallyinduced voltages have the same polarity. Otherwise, the self-induced and mutually-induced voltages have opposite polarity. Parasitic mutual inductance can be significant in very large circuits, even if the frequencies of currents and voltages involved are relatively low; for example, where telephone lines run parallel to electric-power lines over a great distance, 60-cycle hum is induced in the telephone lines and telephone companies must employ special circuits (filters) to eliminate the hum.13 Similarly, parasitic mutual inductance between
f12
x
Fig. 9.34 Flux linkages between parallel current-carrying conductors
13
Between-conductor capacitance also contributes to the coupling. Also, because of nonlinearities in power transformers, the third and fifth harmonics (180- and 300-Hz components) also are present in current on power lines. Telephone companies use filters to eliminate (block) components at and below 300 Hz.
324
parallel telephone lines can introduce what is called crosstalk, where one conversation is superimposed on another. Privacy considerations require telephone companies to take measures to avoid crosstalk. Both problems have been greatly alleviated by a shift to digital transmission. Detailed treatment of such issues is beyond the scope of this book. A standard undergraduate course in electromagnetism will help prepare you to tackle such important problems in practice.
9.14 Transformers Magnetic coupling is the basis of operation for devices called transformers, which use magnetically coupled coils to allow current in one or more coils to induce voltages in one or more other coils, according to Faraday’s law of induction. One or more of the coils might be tapped at various points. The coils driven by sources are called primary coils and the coils driving loads are called secondary coils. For economy, practicing engineers omit coil and refer to a primary coil as a primary and to a secondary coil as a secondary. We limit our discussion to transformers having one primary and one secondary. The secondary might have a center tap. The primary and secondary usually are wound on a common core. The core can be a magnetic material, such as iron, some steels, and ferrite, or a non-magnetic material, such as air (a hollow paper or plastic tube). A transformer having a magnetic core usually is called an iron-core transformer, regardless of the specific composition of the core. A transformer having a non-magnetic core usually is called an air-core transformer, although the core might be (at least in part) paper or plastic. Some transformers for radiofrequency applications have a magnetic core that can be screwed into (or out of) a hollow cylindrical paper or plastic tube on which both coils are wound, which effectively changes the coupling coefficient and the inductances. Adjustable power transformers have a sliding tap on the secondary which effectively changes the number of secondary turns (and thereby the secondary voltage. See (9.80)). Figure 9.35 shows circuitdiagram symbols for various kinds of transformers. Figure 9.36 shows a selection of transformers (not to scale).
9 Inductance
air-core
iron-core
adjustable
center-tapped secondary
Fig. 9.35 Circuit-diagram symbols for transformers
Each term of the form Mðdi=dtÞ in (9.67) is a voltage induced in one coil by current in the other. The voltage induced in one coil depends upon the mutual inductance M and upon the rate of change of the current in the other coil. Thus the voltage induced can be large, even if the coupling coefficient (or mutual inductance) is small. Also, air-core transformers do not exhibit various nonlinear effects and core losses inherent in iron-core transformers. For these and other reasons, most transformers for high-frequency applications (large di=dt ) are air-core. Many for broadcast radio applications (medium di=dt ) are either air-core or adjustable. Almost all transformers for audio ð 20 kHzÞ and power (60 Hz) applications are iron-core. Coupling coefficients range from about 0.01 for some air-core transformers to about 0.99 for some iron-core power transformers. For most audio and high-frequency transformers, linearity is more important than efficiency. For power transformers, efficiency (tight coupling) is as important if not more important than linearity. Air-core transformers are linear, whereas iron-core transformers are at best only approximately so, more nearly linear for smaller than for larger currents and voltages. We limit our treatment to transformers for which linearity is an acceptable approximation, at least for preliminary analysis or design. It is impractical to show the internal structure of a transformer (how the coils are wound) in a circuit diagram, so we use the dot convention described in Section 9.12, where dots are placed at corresponding ends of the primary and secondary windings, as illustrated by Fig. 9.37, where v1 ¼ L1
di1 di2 þM ; dt dt
v 2 ¼ L2
di2 di1 þM : (9.77) dt dt
When preparing to write circuit equations for a transformer, we are free to choose the positive directions for the currents. There is no reason to intentionally
9.14 Transformers
325
Fig. 9.36 Assorted transformers (not to scale): (a) chassis-mount power transformer, (b) PCB power transformer, (c) encapsulated power transformer, (d) (e), PCB-mount pulse transformers, (f) PCB-mount audio transformer (Photographs courtesy of Rapid Electronics, Ltd)
R1 vS + –
i1
i2
+ v1
+ v2
–
–
Fig. 9.37 Dot convention for a transformer
R2
confuse ourselves, so we should always choose the directions and polarities such that both currents enter the dotted terminals, in which case the dotted terminals are positive. If we do that, we will always use the positive sign before the mutual inductance M in the circuit equations.
326
9 Inductance
9.15 Ideal Transformers An ideal transformer is a fictional lossless transformer whose coupling coefficient is unity. Because the coupling coefficient k equals unity, all of the flux produced by the primary links the secondary, and vice versa. That is, f12 ¼ f1 , f21 ¼ f2 , and (9.65) becomes
Fig. 9.38 See Exercise 9.19 i1
M
i2
+
Leq ⇒ v –
L2
L1
Fig. 9.39 See Example 9.12
l1 ¼ N1 ðf1 f2 Þ; l2 ¼ N2 ðf2 f1 Þ ¼ N2 ðf1 f2 Þ: It follows (Faraday’s law) that
The dot convention is extended to three and more coupled circuits by using various dot shapes (e.g., diamonds, squares, etc.), but we do not need that generalization. Exercise 9.19. The shape in Fig. 9.38 represents a rectangular iron core. Draw coils on the left and right parts of the core such that (a) both coils are dotted at the top and (b) one coil is dotted at the top and the other at the bottom. We are at this point unprepared to solve transformer problems, except in certain simple cases, one of which is the subject of the next example. Example 9.12. Obtain an expression for the equivalent inductance seen at the primary winding of a transformer whose secondary is shorted. Solution: Refer to Fig. 9.39. Kirchhoff’s voltage law gives L1
di1 di2 þM ¼ v; dt dt
L2
di2 di1 þM ¼ 0: dt dt
Using the second equation to eliminate i2 from the first gives v¼
L1
(9.78)
M2 di1 M2 : ) Leq ¼ L1 L2 dt L2
dl1 dðf1 f2 Þ ¼ N1 ; dt dt dl2 d ðf1 f2 Þ ¼ N2 ; v2 ¼ dt dt v1 ¼
(9.79)
and thus v2 ¼
N2 v1 ; k ¼ 1: N1
(9.80)
Because an ideal transformer is lossless, the winding resistances equal zero, and all of the power delivered to the primary is delivered to a load connected to the secondary. Refer to Fig. 9.40. The instantaneous power delivered to the primary is given by pin ¼ v1 i1 . Consistent with the passive sign convention, the instantaneous power delivered to the load is given by pout ¼ v2 i2 . For a lossless transformer, pin ¼ pout ) v1 i1 ¼ v2 i2 )
v2 i1 ¼ : v1 i2
(9.81)
Equation (9.80) holds if the coupling coefficient equals unity, even if losses are present, whereas (9.81) holds only if the transformer is lossless. However, if losses are present, the voltages v1 ; v2 are inaccessible (the resistance and inductance are distributed all along each winding), so the fact that (9.80) holds in presence of losses is of little interest unless the losses are small relative to the power delivered to the primary. Also, winding resistance is not the only loss mechanism in a transformer: Time-varying magnetic fields in an iron-core transformer produce eddy currents and attendant losses in the core material.
9.15 Ideal Transformers
327
i1
i2
+ v1
+ v2
–
–
i1 load
N1
N2
i2
+
+
v1
v2
–
–
Fig. 9.40 Power transfer in an ideal transformer (see (9.81)) Fig. 9.41 Conventional current directions and voltage polarities for an ideal transformer. See (9.84)
Equations (9.80) and (9.81) hold only for a transformer having unity (perfect) coupling and no losses. Nonetheless, (9.80) and (9.81) provide a starting point for understanding and designing circuits that incorporate real (not ideal) transformers. The ratio of secondary to primary turns for a transformer is called the turns ratio14 and is denoted by n. n¼
N2 ¼ turns ratio: N1
(9.82)
From (9.80), (9.81), and (9.82), the primary and secondary voltages and currents in an ideal transformer are related as v2 ¼ n v1 ;
i2 ¼ n1 i1 :
(9.83)
Equations (9.83) are valid only for a lossless transformer having unity coupling and only for time-varying (ac) voltages and currents. A transformer (ideal or otherwise) does not pass dc.15 In (9.83), v2 ¼ nv1 if the assumed polarities for v1 and v2 are the same with respect to the dotted terminals. Otherwise, v2 ¼ nv1. In (9.83), i2 ¼ n1i1 if the positive direction for both currents is either into or out of the dotted terminals. Otherwise, i2 ¼ n1i1. To avoid confusion, it is best to take the positive direction of primary current into the dotted terminal of the primary and the positive direction of secondary current out of the dotted terminal of the secondary, and to assign voltage polarities such that the dotted terminals are positive, as shown in Fig. 9.41.16 In that case, (9.83) becomes
Some define the turns ratio as N1 =N2 . In certain configurations, a special kind of transformer, called an autotransformer, can pass dc. See Problems P 9.93 and P 9.94 at the end of the chapter. 16 As a practical matter, there is little reason to do otherwise. 14 15
N2 v 1 ¼ n v1 ; N1 N1 i1 ¼ n1 i1 : i2 ¼ N2 v2 ¼
(9.84)
For an ideal transformer, the least confusing positive directions and polarities of primary and secondary currents and voltages, relative to the dot positions, are those consistent with (9.84), as described by the Italicized statement above. For a non-ideal transformer, the least confusing positive directions of primary and secondary currents, relative to the dot positions, are those that make the sign before the mutual inductance positive. With reference to Fig. 9.41, (9.84) specifies the terminal characteristics of an ideal transformer. Self and mutual inductance are irrelevant and do not appear in equations describing an ideal transformer. Thus, although the symbol for an ideal transformer (Fig. 9.41) suggests inductance in the primary and secondary, an ideal transformer possesses neither self-inductance nor mutual inductance. For an ideal transformer, the only relevant relations are those given by (9.84), where the assumed current directions and voltage polarities are as shown in Fig. 9.41. Ideal transformers do not exist. However, iron-core transformers can achieve tight coupling (coupling coefficients approaching 0.99) and high efficiency (95% or more). The ideal transformer is a somewhat realistic model only for nearly linear (small-signal) operation of a very efficient (low-loss) iron-core transformer. An ideal transformer is a poor model for aircore transformers, whose coupling coefficients are much smaller than unity. Nonetheless, as noted above, the ideal transformer relations (9.84) provide a starting point for specifying transformers and a basis for understanding why and how transformers are used. Some applications follow.
328
9 Inductance
9.16 Applications of Transformers 9.16.1 Source and Load Transformations: Matching Transformers Recall from Chapter 6 that maximum power is transferred from a fixed source to a resistive load if the resistance of the load equals the source resistance. Matching transformers are used to alter the apparent resistance presented to a source by a load, or the apparent output resistance of a source, in order to achieve maximum power transfer in cases where the source and load resistance are different and cannot be changed. Load matching using transformers is based upon the fact that a transformer alters the apparent resistance of a load or source, as illustrated by the following examples and subsequent discussion. Throughout this section, we use only the ideal model for a transformer. Example 9.13. Obtain an expression for the input resistance of the circuit shown in Fig. 9.42. Solution: By definition, Rin ¼
v1 : i1
Thus the ideal transformer transformsthe load seen by a source (v1 ) from R to R n2 , where n is the transformer turns ratio. Such transformation allows maximum power transfer in cases where the load resistance does not equal the source resistance and the load resistance cannot be changed.
Exercise 9.20. It is required that a fixed resistive load RL draw maximum power from a source having fixed output resistance RS , where RS 6¼ RL (Fig. 9.43). A transformer is to be used to provide the required match. Obtain an expression for the turns ratio of the transformer (assumed ideal). An output transformer usually appears as the last (output) element in a circuit; e.g., in the output stage of a multi-stage amplifier. The usual purpose of an output transformer is to match a load to a source (for maximum power transfer). The next example shows how one obtains the The´venin equivalent for a circuit having an ideal transformer as the output element. Example 9.14. Obtain the The´venin equivalent at the terminals a–b for the circuit of Fig. 9.44.
From (9.84)
Rin ¼
n1 v2 1 v2 ¼ 2 : n i2 n i2
RS
By Ohm’s law, v2 =i2 ¼ R. It follows that + –
1 Rin ¼ 2 R: n
v0
Transformer
RL
(9.85) Fig. 9.43 See Exercise 9.20
i1
n
+ Rin ⇒ v 1 –
Fig. 9.42 See Example 9.13
i1 RS
i2 + v2 –
R
+ –
vS
n
i2
+
a +
v1
v2
–
– b
Fig. 9.44 See Example 9.14
9.16 Applications of Transformers
329 RS
Solution: We obtain the open-circuit voltage and the short-circuit current at the terminals a–b. With the terminals open, i2 ¼ 0 and
+ –
RS
n
a
vS
+ –
RL
b
a RL
vS b
n2
(a) load transformation
v2 ¼ voc ¼ n v1 : From (9.84), i2 ¼ 0 ) i1 ¼ 0 and v1 ¼ vS . Thus
RS + –
n
vS
d
voc ¼ n vS :
+ nv S –
RL d
Fig. 9.45 Source and load transformation using a transformer RT
vS : isc ¼ n RS
+ –
The The´venin voltage and The´venin resistance are given by R¼
RL
c
(b) source transformation
With the terminals shorted, v2 ¼ 0 ) v1 ¼ 0 and i1 ¼ vS =RS . Thus
vT ¼ voc ¼ n vS ;
n2 RS
c
voc ¼ n2 RS : isc
From the viewpoint of the load, the transformer transforms the source resistance from RS to n2 RS . Here again, a transformer can be used to achieve maximum power transfer when the source resistance and load resistance are different and cannot be changed.
Examples 9.13 and 9.14 illustrate two useful properties of transformers: A load resistance can be made to appear smaller (n > 1 ) or larger (n<1 ) by interposing a transformer between a source and the load. Similarly, a source and source resistance can be made to appear smaller (n < 1 ) or larger (n > 1 ) by interposing a transformer between a load and the source. In other words, we can use a transformer to change the load seen by a source or the source seen by a load, as shown in Fig. 9.45. Transforming a load as shown in Fig. 9.45(a) is called reflecting the load to the primary of the transformer and transforming a source as shown in Fig. 9.45(b) is called reflecting the source to the secondary of the transformer. In either case, the transformer disappears and the circuit is simplified for further analysis.
N1
N2
vT
RL
ideal transformer
Fig. 9.46 See Example 9.15
Example 9.15. In Fig. 9.46, the source resistance is RT ¼ 100 O and the load resistance is RL ¼ 1 kO. Specify the transformer turns ratio n ¼ N2 =N1 such that maximum power is delivered to the load. Solution: See Fig. 9.45. From the viewpoint of the source, the load resistance is R0L ¼
RL : n2
For maximum power transfer, the apparent load resistance must equal the source resistance. Therefore, rffiffiffiffiffiffi RL RL pffiffiffiffiffi ¼ 10 ¼ 3:16: ¼ RS ) n ¼ 2 n RS
Exercise 9.21. A load is connected to a source through two ideal transformers having turns ratios n1 and n2 , as shown in Fig. 9.47. Under what condition is maximum power delivered to the load?
330
9 Inductance RS
vS
n1
i
n
n2 + –
+ –
source
step up
Fig. 9.47 See Exercise 9.21
transmission line step down (a) high-voltage transmission
i + –
R
i¼
v RL þ 2 R=n2
transmission line
Pa ¼ Irms
2
2R ¼ n2
Vrms RL þ 2 R=n2
Fig. 9.48 See Example 9.16
n + –
v
2R : (9.86) n2
n2RL
R (a)
R/n2
+ –
v
RL
R/n2 (b)
Fig. 9.49 See Example 9.16
Pb ¼ Irms ð2 RÞ ¼
(b) In the circuit of Fig. 9.48b, i¼
R
2
load
(b) low-voltage (transformerless) transmission
2
and the power lost in the transmission lines is given by
RL
R
i
Example 9.16. Obtain expressions for power loss in the transmission-line resistance in the circuits of Fig. 9.48. Assume the transformers are ideal. Solution: (a) We transform all resistances to the primary of the first transformer (see Example 9.13), as illustrated in Fig. 9.49, where
load
v
source
A transformer for which n > 1 is called a step-up transformer because the secondary voltage is higher than the primary voltage. A transformer for which n<1 is called a step-down transformer. Electric utilities use step-up transformers at the origins of long-distance transmission lines and step-down transformers at the destination. This is done primarily to reduce line currents and therefore the sizes of the conductors required to transmit power from a source to a distant load, as illustrated by the following example.
RL
R
RL
9.16.2 Step-Up and Step-Down Transformers
n–1
R
v
2
Vrms RL þ 2R
ð2 RÞ: (9.87)
The point of this example is the following: Comparing (9.86) with (9.87) shows that the effective line resistance is reduced (approximately by the factor n2 ) for the high-voltage transmission system. As a result, much smaller wires can be used to transmit power over long distances, allowing considerable cost savings.
v RL þ 2R
and the power loss in the transmission lines is given by
Exercise 9.22. Obtain an expression for the line current i in the circuit of Fig. 9.48(a)
9.16 Applications of Transformers
331 1:1
RS
+ –
RL
vS iG + –
vG
Fig. 9.50 The boxes represent the metal chassis of two circuits. The two chassis are at different potentials. Connecting the two chassis directly gives rise to a ground-loop current iG which is almost always undesirable and can be destructive or dangerous
+ –
vS
RS RL
iL
+ –
vG
Fig. 9.51 Connecting the circuits without connecting the two chassis17 leads to unpredictable results, because the groundpotential difference vG might be unknown, or to undesirable results, because we do not want the load current to depend upon the ground potential difference
9.16.3 Isolation Transformers Often, it is necessary to couple two circuits that have different ground potentials; for example, two circuits that are some distance apart, such that their earth grounds are at different potentials. Equally often, we might need to connect one circuit whose chassis (or ground plane) is connected to an earth ground to a circuit whose chassis is at a potential different from earth ground. Figure 9.50 shows two such circuits connected in the “obvious” way, where the chassis of the first is connected to the chassis of the other and the source vG represents the potential difference. The resulting current iG is called a ground-loop current and can be large enough to do damage or at least degrade performance of the circuits.
17
Yes, the plural of chassis is chassis: Spelled the same, but pronounced differently.
+ –
vS
RS
+
+
v1
v1
–
–
iL RL
+ –
vG
Fig. 9.52 Using a transformer allows connecting the circuits without providing a current path for the ground potential difference
The ground loop in Fig. 9.50 can be avoided by connecting the circuits as shown in Fig. 9.51, but with this connection, the load current iL is dependent upon both the source vS and the ground potential difference vG . The current produced can also be destructive or dangerous if the ground potential difference is large. If ground potential difference between two circuits is a problem, as illustrated and discussed above, a transformer can be used to isolate the ground potential difference so it has no bearing on the current transferred from one circuit to another or on a measurement of the voltage across a component in a circuit whose ground potential is different from that of the measuring instrument. Figure 9.52 shows how a transformer can isolate the non-zero ground potential from the rest of the (complete) circuit. The transformer turns ratio is one-to-one, so the secondary voltage equals the primary voltage v1 . There is no electrical path from the positive terminal to the negative terminal of the source vG . Thus the ground potential difference vG produces no current and in particular has no effect on the current iL . The ground potential difference vG is effectively cut off or isolated from the rest of the circuit, as illustrated by the equivalent circuit shown in Fig. 9.53. A transformer used to achieve such isolation is called an isolation transformer. A drawback in some applications is inability of a transformer to couple dc; i.e., in Fig. 9.52, the dc component of the source vS (if any) is not passed to the load RL . Lightning can cause brief but huge ground potential differences, as illustrated by Fig. 9.54, which shows two of perhaps several buildings making up an industrial facility. The facility has shared power lines and distributed computing resources connected by various data lines. If lightning strikes nearer one building than the other, the temporary difference in ground
332
9 Inductance
potentials can be several thousand volts or more. Some form of protective isolation (and surge protection) is mandatory in such cases. Isolation transformers also are used to attenuate electrical noise; for example, to prevent noise riding on power lines from reaching sensitive equipment. Transformers intended for such use are designed and constructed specifically for that purpose, and incorporate metallic shields around the primary and secondary windings to reduce capacitive coupling between the windings. The primary shield usually is connected to the transformer case, which is connected to earth ground (e.g., via the ground lead on a three-wire power cord) and the secondary shield usually is connected to the chassis ground on the equipment being isolated.
Design and application of isolation transformers is a subject worthy of an entire book, and cannot be treated to depth here. Interested readers can find numerous references on the web and in libraries.
9.16.4 Center-Tapped Transformers and Balanced Power Refer to Fig. 9.55(a) and focus your attention first on the transformer and the load RL . The transformer secondary and the load share a common ground, and that ground is the reference point for all voltages in the circuit. That is, the voltage vG always equals zero. We assume the transformer secondary voltage is sinusoidal, given by
RS
vS ¼ V0 cosð2p f tÞ
RL
+ –
vG
Fig. 9.53 Equivalent circuit for the circuit shown in Fig. 9.52 (assuming the transformer is ideal and the source has no dc component)
ground potential = 1 kV
ground potential = 10 kV
ground potential = 50 kV
vS = V0
vG = 0 Fig. 9.55 Unbalanced load
(a)
RL
The bottom of the secondary is pinned at zero volts and the upper (dotted) end is alternately positive and negative, which means there is alternately an excess and deficiency of charge at the upper end of the load. Because the voltage at the upper end of the load varies and the voltage at the lower end is fixed (at zero, here), the circuit (or the load) is said to be unbalanced. Regard Fig. 9.55(a) as a snapshot of the circuit at an instant when the secondary voltage and the excess positive charge at the upper end of the load have their maximum values. The vertical line to the right of the load represents a grounded conductor (or metallic surface, such as a section of a chassis) near the load. The load and the conductor comprise a stray capacitance. The positively charged (by vS ) upper end of the load induces an equal and opposite negative charge on the upper end of the nearby conductor, as indicated in the figure. When the secondary voltage reaches its minimum value, as shown in Fig. 9.55(b), the induced charge on the nearby conductor is reversed. Thus there is a non-zero current iG to ground
+++ ++ +
Fig. 9.54 Ground potentials at geographically separated points can be quite different, especially if lightning strikes nearer one point than the other
(9.88)
vS = –V0 iG ≠ 0
vG = 0 (b)
RL
+ ++ +++
iL
––– –– –
vS
– –– –––
+ –
iG ≠ 0
9.17 Concluding Remarks
333 iG
vS
vG = 0
RL
C
Fig. 9.56 Equivalent circuit for the circuit in Fig. 9.55
from the load, which is manifested as a shunt capacitance to ground, as shown in Fig. 9.56. Now refer to Fig. 9.57. In Fig. 9.57, the transformer secondary has a grounded center tap. As a result, the voltages at both ends of the secondary (and the load) are alternately positive and negative, and the charge distributions on the load and the nearby conductor are always equal in magnitude and opposite in sign (assuming the center tap on the secondary is perfect). The charges (electrons) in the nearby conductor simply move back and forth along the conductor as the load voltage alternates. No charges are brought up from (or sent down to) the shared ground, so the ground current equals zero. The load (or circuit) in Fig. 9.57 is said to be balanced. In practice, ground currents are common and problematic. They can cause hum and hiss in home and studio audio systems and sound bars or other disruptive effects in video. They can cause erroneous measurements in instrumentation and control systems. If the potential difference between the chassis of two circuits is large and the chassis are connected, the result can be a destructive and even dangerous current. One purpose of this and the previous section is to make you aware of such phenomena and of methods used to counter them. There are available balanced power systems for use in audio and video studio environments. These systems are essentially equivalent to ideal center-tapped isolation transformers and provide balanced power to loads, as illustrated by Fig. 9.57. Using balanced power sources can eliminate or greatly reduce effects of ground loops and parasitic coupling. The downside of a balanced power system is that both ends of a load are hot. Consequently, a balanced power system is inherently more dangerous than a single-sided system (Fig. 9.55), where one end of the load is at ground potential. It often is necessary to convert a balanced signal to an unbalanced one, or vice-versa. A device (or circuit)
used to accomplish such a conversion is called a balun.18 In most such applications, the balanced and unbalanced sides have different apparent resistances, and the balun must also provide source-load matching. Figure 9.58 shows a balun of a kind you probably used if you ever connected a rooftop TV antenna to a coaxial cable that carries the received signal inside to a TV set. The wires would connect to the antenna and the coaxial cable would connect to the fitting on the lower right. A typical rooftop TV antenna provides a balanced output. One side (the shield) of the coaxial cable is connected to ground at the TV set, so the signal provided to the TV set is unbalanced. The apparent source resistance for the antenna is 300 O and the apparent load presented by the coaxial cable and TV input is 75 O. Baluns for this application convert the balanced output from an antenna to an unbalanced input for a TV set and also provide source-load matching. A balun can consist of a transformer with one center-tapped winding, as illustrated by Fig. 9.59. If the apparent output resistance of the balanced source is RS , the effective source resistance seen by the unbalanced load is given by 2 N2 0 RS ; RS ¼ N1 where N2 =N1 is the turns ratio. For example, a balun used between a rooftop antenna and a coaxial connection to a TV would have a turns ratio of 1=2, which would match the 300 O antenna to the 75 O coaxial cable.
9.17 Concluding Remarks Let us distinguish between inductance, which is a physical phenomenon, and expressions of the form ð diðtÞ 1 t vðt0 Þdt0 ; (9.89) ; iðtÞ ¼ vðtÞ ¼ L dt L 1 where L is a constant having the unit of Vs A1 . Equations (9.89) are mathematical relations between mathematical models for physical signals. Any device or circuit whose terminal characteristics are of the forms given by (9.89) is equivalent to an inductor, whether or not magnetic fields are involved. Various circuits that simulate 18
Balun is a contraction of balanced-to-unbalanced.
9 Inductance
–vS = V0 /2
(a)
Fig. 9.57 Balanced load
+ ++ ++
+
iG = 0
– –– –––
RL
++ + ++ +
––– –– –
iG = 0
+
–vS = –V0 /2
vS = –V0 /2
– –– –––
RL
++ + ++ +
––– –– –
vS = V0 /2
+ ++ ++
334
(b)
1kΩ
i
100 nF
10 kΩ
+
v –
– +
10MΩ
Fig. 9.60 A circuit (gyrator) whose terminal characteristic is that of an inductor
Fig. 9.58 A simple balun
N1
N2
balanced input
unbalanced output
Fig. 9.59 Circuit diagram for a balun
inductance have been devised. For example, for sinusoidal inputs having frequencies between about 3 and 800 Hz, the terminal characteristic of the circuit shown in Fig. 9.60 is approximately that of a 1 kH inductor.19,20 A coil having that inductance would be huge. The point of the remarks above is that inductive effects can be achieved without using inductors. Indeed, inductive effects are usually achieved that way in active linear signal-processing and transmission systems at frequencies below 100 MHz or so. Believe it or not, circuits such as the one shown in Fig. 9.60 can be cheaper and much smaller than coils. Regardless of how they are achieved, inductive effects are important in virtually all linear electrical
and electronic circuits. They are important in electric power systems and in machinery, where they arise naturally in the windings of transformers and motors. They are important in radio and television transmitters and receivers and in almost all high frequency – high power applications, where inductive effects cannot be achieved by electronic mimicry. They are important wherever unintentional inductive coupling can be significant; for example, in long conductors near power lines or in electronic systems where a power supply is on the same board or chassis as other circuitry. If you intend to engage in circuit design, or to work in the power generation and distribution field, or to work as a plant engineer in a plant using electrical machinery, or to work in any field involving radio transmission and reception, or in a host of other disciplines, you need to know about inductance and its effects.
9.18 Problems
Section 9.4 is prerequisite for the following problems.
19
Paul Horowitz and Winfield Hill, The Art of Electronics, Cambridge University Press, New York, 1989, p 304. 20 You will be able to show this after studying Chapter 12.
P 9.1 The inductance of a long, tightly wound air-core coil having N turns, length l, and diameter d is given by
9.18 Problems
335
L¼
p m0 N 2 d 2 : 4l
The meter and Henry are inconvenient (too-large) units for specification and design of air-core inductors. Modify the relation above such that the diameter and length of the coil are expressed in centimeters and the inductance is given in microhenries. P 9.2 Wheeler’s formula21 for the inductance of a single-layer air-core coil is L¼
N 2 d2 ; 18d þ 40l
where the coil diameter d and length l are expressed in inches and the inductance is expressed in microhenries. Rewrite this formula such that the quantities involved are expressed in SI units. P 9.3 Modify the relation (9.8) in the text for the inductance of an air-core coil such that the diameter and length of the coil are expressed in millimeters. P 9.4 A tightly wound, single-layer coil is stretched (like a spring). Does the inductance of the coil increase or decrease? Why? P 9.5 If you need a specific inductance from an aircore coil and you want the coil to occupy the least volume possible, would you make a short, fat coil or a long, thin one? Or does it matter? Assume the relation (9.8) in the text is valid. P 9.6 If M turns are removed from a long, tightly wound, single-layer air-core inductor having N turns, by what percentage is the inductance reduced?
with I0 ¼ 20 mA and t ¼ 100 ms. Obtain an expression for the voltage across the inductor and compute the value of the voltage for t ¼ t. What is the maximum magnitude of the voltage and when does it occur? P 9.8 Repeat Problem P 9.7 assuming that the winding (equivalent series) resistance of the inductor is 1 O. P 9.9 The current through a 50-mH inductor is given graphically in Fig. P 9.1. Draw a graph of the voltage across the inductor for 0 t 15 ms. P 9.10 Repeat Problem P 9.9 assuming that the winding (equivalent series) resistance of the inductor is 1 O. P 9.11 The current through an inductor having inductance L ¼ 500 mH is given graphically in Fig. P 9.2. Draw a graph of the voltage across the inductor for t > 0. P 9.12 Repeat Problem P 9.11 assuming that the winding (equivalent series) resistance of the inductor is 1 O. P 9.13 In Fig. P 9.3, R ¼ 10 kO; L ¼ 1 mH. The voltage across the resistor is given by vR ¼ V0 ½1 þ 0:5 cosð2 p f tÞ þ 0:05 cosð20 p f tÞ; V0 ¼ 5 V; f ¼ 5 MHz: (a) Obtain an expression for the voltage vL across the inductor. (b) Assuming the source voltage vS remains the same, obtain an expression for the voltage across the resistor if the inductor is replaced by a short circuit. i (mA)
Section 9.5 is prerequisite for the following problems.
10 t (ms) 6
P 9.7 The current through an inductor having inductance L ¼ 5 mH is given by iðtÞ ¼
0;
I0 1 et=t ;
t 0; t > 0;
10
–10
Fig. P 9.1 See Problem P 9.9 i (mA) 100 t (μs) 50
21 Wheeler, H.A., Simple Inductance Formulas for Radio Coils, Proc. IRE, vol 16, p 1398 (Oct. 1928).
Fig. P 9.2 See Problem P 9.11
336
9 Inductance
(b) P 9.14 Refer to Fig. P 9.4. The current through the inductor is given by iL ðtÞ ¼ IL cosð2p f tÞ: Obtain an expression for the current through the capacitor, the current through the resistor, and the total current i(t). Use trigonometric identities to express the total current as a single sinusoid of the form iðtÞ ¼ I cosð2p f t þ yÞ: P 9.15 In Fig. P 9.5, the fuse will melt if the current through the fuse exceeds 25 A. The switch is closed at t ¼ 0. At what time does the fuse begin to melt? P 9.16 In Fig. P 9.6, the source voltage is given by vS ðtÞ ¼ VS cosð2p f tÞ, with VS ¼ 25 V and f ¼ 10 kHz. It is known that the voltage across the resistor has the form vR ðtÞ ¼ VR cosð2p f t þ yÞ. Find VR and y. P 9.17 Refer to Fig. P 9.7. Under what condition is the output approximately proportional to the integral of the input? P 9.18 Refer to Fig. P 9.8. Obtain an expression for the load voltage vL ðtÞ. P 9.19 The turns in an inductor are conductors separated by a dielectric (air or some insulating material).
Thus an inductor exhibits stray shunt capacitance. In Fig. P 9.9, C represents stray capacitance and vS ¼ VS cosð2p f tÞ. Assume that the current through the inductor equals zero for t ¼ 0. Obtain an expression for the frequency f for which the rms amplitude of the current through the capacitor equals the rms amplitude of the current through the inductor. Section 9.6 is prerequisite for the following problems. P 9.20 Refer to Fig. P 9.10. Obtain an expression for the indicated current i(t) (i) assuming the switch has been open for a very long time and is closed at t ¼ 0 and (ii) assuming the switch has been closed for a very long time and is opened at t ¼ 0. P 9.21 In Fig. P 9.11, the diode is ideal. The switch is opened at t ¼ 0, having been closed for a very long +
+ –
R
vS
R = 2.2 kΩ L = 75 mH
Fig. P 9.6 See Problem P 9.16
+ L
+
vL
L
–
+ vR –
Fig. P 9.3 See Problem P 9.13
–
R
+ –
vS
vR
+
vin
vL
–
+
L
vout
R
–
–
Fig. P 9.7 See Problem P 9.17
i
iL
iC
R L
vL
– C
R
Fig. P 9.4 See Problem P 9.14
R1
L
+ –
+
vS
RL
Fig. P 9.8 See Problem P 9.18
fuse
+ V0 –
R2
L
vS
+ –
V0 = 100V, R1 = 2 Ω, R2 = 100 Ω, L = 100 mH
Fig. P 9.5 See Problem P 9.15
Fig. P 9.9 See Problem P 9.19
L
C
9.18 Problems
337
time. Obtain an expression for the current i(t) though the diode for t 0. P 9.22 In Fig. P 9.12, the switch is closed at t ¼ 0, having been open for a very long time before. Obtain an expression for the voltage vL ðtÞ. Section 9.7 is prerequisite for the following problems. Problems in this section assume that coils connected in series or in parallel are connected in such a way that there are no magnetic flux linkages between the coils. R1
2R
R2 + –
+
2R L
V0
–
i
V0 i
(b)
(a) + V1 – i
–
R1 R2 L
R2
+
L
+ V2 –
V2
R1
+ –
i
(d)
(c) R1
R2 –
+
R
V2 + V0
R3
–
L
+ R V1 –
L i
–
R V0
i
R
(f)
+ R V0 –
L i
R
R
(e)
+
L
V1
P 9.23 Show that the equivalent inductance of a parallel connection of N identical ideal inductors, each having inductance L, is given by Leq ¼ L=N. P 9.24 Two identical inductors, each having inductance L and winding resistance R, are connected in parallel. Find an equivalent single inductor (equivalent inductance and equivalent winding resistance). P 9.25 Suppose you are building a prototype circuit that requires a precision 10 mH air-core inductor. You have on hand a selection of precision 5 mH air-core inductors, having various lengths and diameters. You intend to obtain a 10 mH inductor by connecting two 5 mH inductors in series. Should you use the shortest or the longest of the 5 mH inductors you have on hand? Justify your answer. P 9.26 In Fig. P 9.13, the switch is open for t < 0 and closed at t ¼ 0. Obtain expressions for the voltage vðtÞ and the currents i1 ðtÞ; i2 ðtÞ for t > 0. P 9.27 Two inductors having equal winding resistances and time constants t1 and t2 ¼ 2t1 are connected in series. What is the time constant of the series connection? Assume the inductances add. P 9.28 Two inductors having equal inductances and time constants t1 and t2 ¼ 2t1 are connected in series. What is the time constant of the series connection? Assume the inductances add. P 9.29 An inductor having time constant t1 is connected in series with one having time constant t2 . Express the time constant of the series connection in terms of (a) the winding resistances and (b) the inductances of the individual inductors. Assume the inductances add.
R
L
(g)
R i
(h)
+
L
R
R1
–
R
Fig. P 9.11 See Problem P 9.21
vL
–
–
i
V0
+ L
Fig. P 9.12 See Problem P 9.22
Fig. P 9.10 See Problem P 9.20
+
R2
V0
R
L
i1
i2
L1
L2
+ –
V0
Fig. P 9.13 See Problem P 9.26
+
v –
338
9 Inductance
P 9.30 A long, tightly wound, single-layer, N-turn, air-core inductor having length l, diameter d, and inductance L given by p m0 N 2 d2 L¼ 4l is cut into two pieces of equal length. Assume each piece is also a long coil. What is the inductance of each piece? Is the sum of the inductances equal to the inductance of the original coil? P 9.31 A short, tightly wound, single-layer, N-turn, air-core inductor having length l, diameter d, and inductance L given by L¼
R +
+ V0
–
R
Section 9.8 is prerequisite for the following problems. P 9.32 In Fig. P 9.14, the switch is closed for t < 0, opened at t ¼ 0, and closed at t ¼ 5 ms. Sketch neatly and label fully graphs of the current i(t), the voltage vL ðtÞ, and the energy wðtÞ stored in the inductor for the times during which they are changing. Use the same time scale for all three graphs and identify the times during which the inductor is absorbing energy and the times during which it is delivering energy to the circuit. P 9.33 Refer to Fig. P 9.15, where vS ¼ Vs cosðo tÞ. Assume the current through the inductor is given by 1 i L ðt Þ ¼ L
ðt
vS ðt0 Þdt0
0
and obtain an expression for the total stored energy as a function of time. Show that the total stored energy is independent of time if C¼
1 : o2 L
i
–
L = 50 mH
Fig. P 9.14 See Problem P 9.32
vS
iL
+ –
L
Fig. P 9.15 See Problem P 9.33
m0 N 2 d 2 0:579 d þ 1:273 l
is cut into two pieces of equal length. (a) If the same formula applies, what is the inductance of each of the two coils? (b) Is the sum of the inductances equal to the inductance of the original coil? If not, why not? (c) Are inductors in series necessarily additive?
V0 = 25 V
vL R = 10 Ω
L
vS
+ –
iR
iL
R
L
iC C
i
C
C
Fig. P 9.16 See Problem P 9.34
P 9.34 Refer to Fig. P 9.16, where vS ¼ Vs cosðo tÞ 1 and C ¼ ðo2 LÞ . (a) Obtain an expression for the instantaneous total energy stored in the electric and magnetic fields associated with the capacitor and inductor. (b) Obtain an expression for the energy dissipated per cycle (period) of the source vS . (c) The quality factor Q for a circuit in sinusoidal steady state is defined as Q ¼ 2p
maximum of instantaneous stored energy : energy dissipated per period of the source
Show that the quality factor of the circuit in Fig. P 9.16 is given by Q ¼ R=ðoLÞ. P 9.35 In Fig. P 9.17, iS ¼ Is cosðo0 tÞ, with pffiffiffiffiffiffi o0 ¼ 1 LC. Find the instantaneous voltage across the source. (This is an example of what is called series resonance. You will learn more about resonance in Chapter 12). P 9.36 In Fig. P 9.18, vS ¼ Vs cosðo0 tÞ, with pffiffiffiffiffiffi o0 ¼ 1 LC. Find the instantaneous current iS . (This is an example of what is called parallel resonance. You will learn more about resonance in Chapter 12).
9.18 Problems
339 +
vL
–
+
vS
Fig. P 9.17 See Problem P 9.35
C
iS
–
–
vS Fig. P 9.18 See Problem P 9.36
iL L
i
vC
iS + –
C
+ L
iC
v
+ –
R
L
Fig. P 9.19 See Problem P 9.39
C
Section 9.10 is prerequisite for the following problems. Section 9.9 is prerequisite for the following problems. P 9.37 A sinusoidal current having frequency f and peak amplitude I passes through an axial-lead capacitor having capacitance C and series self-inductance L. Assuming a lumped-constant model is applicable, obtain an expression for the frequency at which the rms voltage drop across the self-inductance equals 1% of the rms voltage drop across the capacitance. Assume the voltage across the capacitance equals zero for t ¼ 0. P 9.38 For some purposes, a coil can be modeled as an inductance in parallel with a parasitic capacitance, the latter arising from the fact that the turns of the coil are charge-carrying conductors separated by an insulating medium. A sinusoidal voltage having frequency f and peak amplitude V0 is impressed on a coil having inductance L and parallel parasitic capacitance C. Obtain an expression for the frequency at which the rms amplitude of the current through the capacitance equals 1% of that through the inductance. Assume the current through the inductance equals zero for t ¼ 0. P 9.39: The circuit in Fig. P 9.19 is a simplified high-frequency model for an axial-lead film resistor, where R is the nominal resistance, L is equivalent series inductance arising mainly from the internal (spiral) structure of the resistor, and C is the end-to-end capacitance. Let R ¼ 1 kO, L ¼ 800 nH, C ¼ 0:4 pF, and pffiffiffi v ¼ VS cosð2p f tÞ, with VS ¼ 2 V. Simulate the circuit and plot the ratio Vrms =Irms versus the frequency f of the source, for 10 MHz f 1 GHz. For what range of frequencies does the resistor behave like an ideal resistor?
P 9.40: The dc output of a certain power supply is 5 V. For a 0:5 O resistive load, the ripple factor of the load voltage is g ¼ 0:002. (a) What is the rms amplitude of the ac component of the load voltage? (b) Assuming the ripple is a 120 Hz sinusoid, what is the ripple factor for the load voltage if a 500 mH inductor is connected in series with the load? (c) : Simulate the circuit to check your answer. P 9.41: The voltage across a 1O resistive load is given by v ¼ Vdc þ Vac cosð2 p f tÞ; with f ¼ 5 kHz, Vdc ¼ 25 V, and Vac ¼ 25 mV. (a) What is the ripple factor? (b) Specify a series choke such that the rms ripple is reduced by the factor 2 104 . (c) Use a simulation to check your answer. P 9.42 In Fig. P 9.20, R ¼ 0:5 O and vS ¼ Vdc þ pffiffiffi Vac cosðo0 t þ yÞ with Vdc ¼ 50 V, Vac ¼ 5 2 mV, and f0 ¼ 120 Hz. The required ripple factor is 106 . Specify the inductance L. Section 9.11 is prerequisite for the following problems. P 9.43 The 20 A current through a 2 H inductor is reduced to zero in 20 ms by a circuit breaker. Estimate the magnitude of the average voltage across the inductor during that time. P 9.44 In Fig. P 9.21, the fuse will melt if the current through the fuse exceeds 2.5 A. The current iS equals zero for t 0 and is given by
340
9 Inductance + vL
vS
Fig. P 9.20 See Problem P 9.42
+
L
+ –
R
i
+
–
v
–
R2
vR –
R1
+ V0
Fig. P 9.23 See Problem P 9.46
L
–
+
R
L
iS
vL –
R = 5 Ω, L = 2 H
Fig. P 9.21 See Problem P 9.44
R1
a
b +
– +
V0
L
R2
Fig. P 9.24 See Problem P 9.47
v –
i
a
L1
+
Fig. P 9.22 See Problem P 9.45
v –
M
L2
b
iS ¼ I0 ½1 expðt=tÞ; I0 ¼ 5 A; t ¼ 100 ms for t > 0. At what time will the fuse begin to melt? Assume the fuse opens completely in 15 ms and estimate the magnitude of the average voltage across the fuse body during that time. P 9.45 Refer to Fig. P 9.22, where the switch is moved from a to b at t ¼ 0, having been at a for t < 0. Assume a make-before-break switch, so there is no arcing. (a) Obtain an expression for the voltage vðtÞ across the resistor R2 . (b) Let V0 ¼ 3 V, R1 ¼ 100 O, R2 ¼ 100 kO, and L ¼ 500 mH. Construct a graph of the voltage vðtÞ versus t for 0 t 5t, where t is the time constant for t > 0. (c) For the parameter values given in part (b), how much energy is eventually dissipated by the resistor R2 ? P 9.46 Refer to Fig. P 9.23, where the switch is opened at t ¼ 0, having been closed for t < 0. (a) Obtain an expression for the voltage vðtÞ across the resistor R2 . (b) Let V0 ¼ 9 V; R1 ¼ 10 O; R2 ¼ 10 kO; L ¼ 1 H . Construct a graph of the voltage vðtÞ versus t for 0 t 5t, where t is the time constant for t > 0.
Fig. P 9.25 See Problem P 9.48
Section 9.12 is prerequisite for the following problems. P 9.47 Figure P 9.24 depicts coils wound on a shared magnetic core. Assign dots to the terminals of the coupled coils. P 9.48 Obtain the equivalent inductance at the terminals a–b of the circuit shown in Fig. P 9.25. P 9.49 Two air-core coils having inductances 25 mH and 50 mH are arranged such that the mutual inductance between them is 7:1 mH. What is the coupling coefficient for the arrangement? P 9.50 Two air-core coils having inductances 25 mH and 50 mH are connected in series, whereupon it is found that the total inductance is 90 mH. (a) What is the mutual inductance between the coils? (b) What would the total inductance become if the leads of one of the coils were reversed but the relative positions of the coils were unchanged?
9.18 Problems
341
P 9.51 You are given two air-core coils having inductances L1 and L2 . If you intend to obtain an inductance L ¼ L1 þ L2 by connecting the coils in series, should you place them end to end, with the windings in the same direction, or side by side, or far apart, or how, otherwise? P 9.52 You are given two air-core coils, each having equal inductance L. If you intend to obtain an inductance L=2 by connecting the coils in parallel, should you place them end to end, with the windings in the same direction, or side by side, or far apart, or how, otherwise? P 9.53 In Fig. P 9.26, vS ¼
0; VS ;
t 0; t > 0:
(a) Obtain an expression for the voltage vðtÞ for t > 0. (b) Move the dot on one inductor to the other end of the inductor (reverse the leads on one inductor) and repeat part (a). Section 9.13 is prerequisite for the following problems. P 9.54 A pessimistic estimate for the inductance per unit length of a long straight wire distant from other conductors is 50 nHm1. Each of the two leads on a certain 10 kO axial-lead resistor is approximately 2.5 cm long and the current through the resistor is sinusoidal. Find the frequency for which the rms voltage due to lead inductance equals 1% of the total rms voltage across the resistor. P 9.55 Axial and disc capacitors have relatively long leads and exhibit stray (parasitic) inductance. Inductors exhibit stray (parasitic) capacitance because the windings are neighboring current-carrying conductors. Thus, at sufficiently high frequencies, it might
be necessary to model capacitors and inductors as shown in Fig. P 9.27. (1) For the model of a capacitor in Fig. P 9.27(a), assume iðtÞ ¼ I0 cosð2p f tÞ and vC ð0Þ ¼ 0 and obtain an expression for the frequency at which the voltage across the parasitic inductance LP equals 1% of the voltage across the capacitance C. (2) For the model of an inductor in Fig. P 9.27(b), assume vðtÞ ¼ V0 cosð2pf tÞ and iL ð0Þ ¼ 0 and obtain an expression for the frequency at which the current through the parasitic capacitance Cp equals 1% of the current through the inductance L. P 9.56 Refer to Fig. P 9.28. Let k denote the coupling coefficient for two coils in different branches of a certain circuit. The currents through the coils are sinusoidal, given by i1 ðtÞ ¼ I1 cosð2p f1 tÞ;
i2 ðtÞ ¼ I2 cosð2p f2 tÞ:
(a) Obtain expressions for the voltages v1 ðtÞ and v2 ðtÞ across the coils, assuming both currents enter dotted terminals. (b) Let I1 ¼ I2 ¼ I, L1 ¼ L2 ¼ L, f2 ¼ a f1 . Obtain a relation between k and a for which the rms amplitude of the voltage induced in coil 1 by the current in coil 2 equals the rms amplitude of the voltage induced in coil 1 by the current in coil 1. (c) Let I2 ¼ b I1 , L1 ¼ L2 , f2 ¼ f1 . Obtain a relation between k and b for which the rms amplitude of the voltage induced in coil 1 by the current in coil 2 equals the rms amplitude of the voltage induced in coil 1 by the current in coil 1. (d) Comment on the implications of the solutions to parts (b) and (c).
CP C
i
LP +
L (b)
(a) L1
v –
Fig. P 9.27 See Problem P 9.55 +
vS
+ –
M
R
v
i1
+
v1
–
i2
+
v2
– L2
Fig. P 9.26 See Problem P 9.53
L1
M
Fig. P 9.28 See Problem P 9.56
L2
–
342
9 Inductance
Section 9.14 is prerequisite for the following problems. P 9.57 Obtain an expression for the equivalent inductance seen at the primary winding of a transformer whose secondary is open. Ignore winding resistance. P 9.58 Figure P 9.29 shows a transformer whose primary and secondary are connected in parallel. Obtain an expression for the equivalent inductance at the terminals a–b. P 9.59 Refer to Fig. P 9.30, where L1 ¼ 25 mH, L2 ¼ 400 mH, the coupling coefficient between the primary and secondary coils is 0.9, and vðtÞ ¼ V0 cosð2p f tÞ, with V0 ¼ 10 V and f ¼ 100 Hz. Find the rms amplitude of the current i(t), given that i(0) ¼ 0. P 9.60 In Fig. P 9.31, the switch is opened at t ¼ 0, having been closed for a very long time. Assume the transformer coupling coefficient is nearly unity, such that v2 ffi n v1 , where n is the transformer turns ratio. Obtain an expression for the voltage v2 for t > 0. Calculate the maximum magnitude of v2 if V0 ¼ 12 V, R2 ¼ 40R1 , and n ¼ 50.
P 9.61 What is the equivalent resistance at the primary of an ideal transformer whose secondary is open? P 9.62 What is the equivalent resistance at the primary of an ideal transformer whose secondary is shorted? P 9.63 Obtain the The´venin and Norton equivalent circuits at the terminals a–b for the circuit shown in Fig. P 9.32. The transformers are ideal. P 9.64 The output resistance for a source that is to drive a 2 kO resistive load is RS ¼ 50 O. Specify the turns ratio for an ideal transformer which, if inserted between the source and the load, will ensure maximum power transfer. P 9.65 In Fig. P 9.33, the transformer is ideal and the voltage across the resistor is given by vR ¼ V0 cosð2 p f tÞ. Obtain an expression for the source voltage v. P 9.66 An inductor having inductance L is connected to the secondary of an ideal transformer having turns ratio n ¼ N2 =N1 . Obtain an expression for the inductance seen at the primary terminals. P 9.67 A capacitor having capacitance C is connected to the secondary of an ideal transformer having
Section 9.15 is prerequisite for the following problems. + i2 i1
i
a
+
+
v1
v
+
R2
–
M
+
R1
v1
V0
+ L1
L2
–
i
–
Fig. P 9.31 See Problem P 9.60
L2 v2
L1
–
–
R1
– b
v0
N1
N2
R2
N3 N4
b
Fig. P 9.32 See Problem P 9.63 i +
+
v –
Fig. P 9.30 See Problem P 9.59
a
+ –
Fig. P 9.29 See Problem P 9.58
L1
v2
L2
+ v –
vR – N1 N2 R
Fig. P 9.33 See Problem P 9.65
L
9.18 Problems
343
turns ratio n ¼ N2 =N1 . Obtain an expression for the capacitance seen at the primary terminals. P 9.68 Suppose you wish to use an ideal model for a certain very efficient physical transformer whose coupling coefficient is near unity. You know from measurements that the effective turns ratio of the transformer for a 1 kHz sinusoidal primary voltage is n ¼ 10, what would you use for the turns ratio in the model if the voltage is a 10 kHz sinusoid?
ings. Is it a good idea to use the wire size that makes the primary and secondary dc resistances equal? If so, why? If not, why not, and what might be a better objective? P 9.74 Outputs of power-plant generators are stepped up in stages to the very high voltages used for long-distance transmission to avoid excessive voltage differences and possible arcing between the primary and secondary windings of any one transformer. The output VG rms ¼ 24 kV of a certain powerplant generator must be stepped up to V 1 rms ¼ 648 kV for transmission. If the maximum allowable rms voltage between the primary and secondary windings of any one transformer is 220 kV, how many transformers are required and what are their turns ratios? P 9.75 In Fig. P 9.34, VG rms ¼ 24 kV; V1rms ¼ 648 kV; VL rms ¼ 440 V, and the load is RL ¼ 500 mO. The numbers of turns ðN1 ; N2 Þ are the same for each transformer except the last. The overall efficiency of the system is 94%, which means that 94% of the power produced by the generator is delivered to the load. Assume that each transformer is ideal and calculate the turns ratio n of the final step-down transformer and the resistance of the transmission line. P 9.76 You want to put a speaker by your swimming pool, 50 m from your amplifier. You plan to use step-up and step-down audio transformers to allow use of small wire from the amplifier to the speaker. The effective resistance of the speaker is 8 O and the output resistance of the amplifier is 1 O. The amplifier can deliver 200 W to an 8 O load. You have decided that the maximum loss in the wire should be no more than 5% of the power that would be delivered to the speaker if the wire resistance were zero. You have also decided to use AWG 24 copper wire to run from the amplifier to each speaker because you have that wire on hand. Specify the turns ratios for the step-up and step-down transformers. (Assume the transformers are ideal). P 9.77 Refer to Fig. P 9.35, where the ground symbol represents earth ground. The source vS is sinusoidal with frequency greater than zero. Suppose you wish to observe the source voltages vS ðtÞ and vL ðtÞ simultaneously, using a two-channel oscilloscope.
Section 9.16 is prerequisite for the following problems. P 9.69 A source whose output resistance is 50 O must be matched for maximum power transfer to a 200 O load. What turns ratio is required of a matching transformer? P 9.70 The output resistance of a certain audio amplifier is 150 O and voltage is the output of interest. The load resistance is 3:2 O. Specify the turns ratio for a transformer that will match the amplifier to the load (for maximum power transfer). P 9.71 The output resistance of a certain microphone element is 2 kO. The input resistance of an amplifier is 20 kO. Should a transformer be used to match the microphone to the amplifier to maximize power transfer? Justify your answer. P 9.72 A woodworker friend of yours just bought an industrial power tool having a 20 hp, 480 V (rms), 60 Hz motor. He has a 240 V outlet in his basement workshop. The outlet is protected by a 30 A circuit breaker. He intends to use a transformer to boost the 240 V to the 480 V required by the tool. Is that a good idea? Explain why or why not. P 9.73 You are asked to specify the wire size for winding the secondary of a high-efficiency transformer whose coupling coefficient is close to unity. The numbers of primary and secondary turns in are N1 ¼ 500 and N2 ¼ 50, respectively. AWG 28 wire will be used for the primary. Copper wire is required for both wind-
N1
Fig. P 9.34 See Problem P 9.75
N2
N1
N2
N1
RT /2
N2
N2 N1
N2 N1
N 2 N1
n
+
+
+
+
generator vG
v1
v2
vL
–
–
–
–
RT /2
RL
344
+ – vS
9 Inductance
balanced line in
N
unbalanced line out
+
L C
RL
vL
N
–
Fig. P 9.36 See Problem P 9.79 Fig. P 9.35 See Problem P 9.77
The oscilloscope is properly grounded through the three-conductor power cord and each probe has a center (positive) point and a ground clip. Describe why and how you would use an isolation transformer to perform this measurement. P 9.78 You and a co-worker wish to test circuits you have designed for transmitting and receiving data over a long coaxial cable. You put the transmitter in one outbuilding on your industrial campus and the receiver in another, about 1 km distant, and run a coaxial cable between them. The transmitter and receiver chassis are
connected to earth ground at their locations. If you connect the coaxial cable directly to both circuits, the shield on the cable will connect the chassis. Why might that be a problem? How could you use an isolation transformer to avoid a ground loop current? P 9.79 Figure P 9.36 shows a balun consisting of a center-tapped autotransformer. The balanced input in Fig. P 9.36 is from a source having output resistance RS ¼ 300 O. Assume the balun can be modeled as an ideal transformer. What is the effective source resistance seen at the (unbalanced) output terminals?
Chapter 10
Complex Arithmetic and Algebra
The real part of a complex number z is denoted by Refzg and the imaginary part by Imfzg; i.e.,
In the remainder of the book, we make extensive use of complex arithmetic and algebra. This short chapter gives a brief review that subject and establishes a consistent notation. Working knowledge of the basic definitions, procedures, and relations reviewed here is essential to mastering material presented in subsequent chapters. Also, the terminology and notation associated with engineering applications of complex mathematics have not been standardized, and the terminology and notation introduced here are those used in this book. Even if your mastery of complex arithmetic and algebra is such that you need only lightly skim this chapter, give special attention to the definition of the four-quadrant inverse tangent in Section 10.6 and the definitions of the symbols ff and ∡ in Section 10.8.
Both the real part and the imaginary part of a complex number are real. For example, if z ¼ 3 j4 then Refzg ¼ 3 and Imfzg ¼ 4. Do not make the common mistake of including j in the imaginary part of a complex number. In applications, complex numbers and expressions often are dimensioned, in which case the real part and the imaginary part must have the same dimension.
10.1 Complex Numbers
10.2 Complex Arithmetic
A complex number is a number of the form a þ jb, where a and b are real numbers and j is the imaginary unit1 defined by j¼
pffiffiffiffiffiffiffi 1:
(10.1)
The number a is the real part of the complex number and the number b is the imaginary part.
1 Mathematicians, physicists, and others use i to denote the imaginary unit. Electrical engineers use j because they use i to denote electric current.
Refzg ¼ real part of z; Imfzg ¼ imaginary part of z:
(10.2)
Conversely, z ¼ Refzg þ j Imfzg
(10.3)
The rules and results of complex arithmetic are generally consistent with those of real arithmetic; for example, the sum, difference, product, and quotient of two complex numbers (defined below) reduce to the sum, difference, product, and quotient, respectively, of the real parts of the numbers if the numbers are real (if their imaginary parts are equal to zero). But a few generalizations are necessary: • Two complex numbers are equal if and only if the real parts are equal and the imaginary parts are equal. • A complex number equals zero if and only if the real part and the imaginary part of the number are both equal to zero.
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_10, # Springer ScienceþBusiness Media B.V. 2011
345
346
10 Complex Arithmetic and Algebra
• The negative of a þ j b is p a ffiffiffiffiffiffiffiffiffiffiffiffiffiffi j b. ffi • The magnitude of a þ j b is a2 þ b2 (see Section 10.4). • The sum of two (or more) complex numbers is obtained by adding the real parts and (separately) the imaginary parts; for example, ð3 þ j4Þþ ð2 j6Þ ¼ 5 j2. In general, ða1 þ j b1 Þ ða2 þ j b2 Þ ¼ ða1 a2 Þ þ jðb1 b2 Þ:
(10.4)
• The product of two complex numbers is obtained by treating each number as a binomial; for example, ð3 þ j4Þð2 j6Þ ¼ 6 j18 þ j8 j2 24, which, because j2 ¼ 1, reduces to 30 j10. In general, ða1 þ j b1 Þða2 þ j b2 Þ ¼ ða1 a2 b1 b2 Þ þ j ða1 b2 þ a2 b1 Þ:
(10.5)
• The reciprocal of a complex number z ¼ a þ j b is the number z1 ¼ x þ j y such that z z1 ¼ 1. To determine x and y in terms of a and b, we must solve the equation ða þ j bÞðx þ j yÞ ¼ 1: This gives ða þ j bÞðx þ j yÞ ¼ ða x b yÞ þ j ðb x þ a yÞ ¼ 1 þ j 0: Equating the real parts and imaginary parts (separately) and solving the resulting simultaneous equations yields a b ; y¼ 2 : x¼ 2 a þ b2 a þ b2 Thus the reciprocal of a complex number a þ j b is given by ða þ j bÞ1 ¼
1 a jb : ¼ 2 a þ j b a þ b2
z 1 a1 þ j b 1 ¼ ¼ ða2 þ j b2 Þ1 ða1 þ j b1 Þ z 2 a2 þ j b 2 ða1 þ j b1 Þða2 j b2 Þ a22 þ b22
3 þ j4 ð3 þ j4Þð2 þ j6Þ 18 þ j26 ¼ ¼ 2 j6 22 þ 62 40 18 26 ¼ þ j ¼ 0:45 þ j 0:65: 40 40 Complex arithmetic differs from real arithmetic in another significant respect: Whereas a set of distinct real numbers can be ordered (e.g., listed from smallest to largest), a set of complex numbers cannot be ordered. As a result, one cannot say whether one complex number is larger or smaller than another; in other words, inequalities of the form z1 < z2 are undefined if z1 or z2 is complex. Otherwise, the rules of basic arithmetic for complex numbers are the same as those for real numbers. If z1, z2, and z3 denote complex numbers, then • Addition and multiplication are commutative, such that z1 þ z2 ¼ z2 þ z1 and z1 z2 ¼ z2 z1 • Addition and multiplication are associative, such that z1 þ ðz2 þ z3 Þ ¼ ðz1 þ z2 Þ þ z3 and z1 ðz2 z3 Þ ¼ ðz1 z2 Þz3 ; and • Multiplication is distributive over addition, such that z1 ðz2 þ z3 Þ ¼ z1 z2 þ z1 z3 . Exercise 10.1. Given z1 ¼ 3 þ j4; z2 ¼ 1 j2; z3 ¼ j5; z4 ¼ 5 þ j, verify each of the following: ðaÞ z1 þ z2 z3 þ z4 ¼ 1 j 2; ðbÞ z1 ð1 z2 Þ ¼ 8 þ j 6; ðcÞ 6 z1 þ 4 ðz2 z4 Þ ¼ 42 þ j 12; ðdÞ z1 z2 ¼ 11 j 2; ðeÞ z3 z4 ¼ 5 j 25; z2 ðf Þ z1 z3 ¼ 20 þ j 15; ðgÞ ¼ 0:4 j 0:2; z3 z1 z3 1 ¼ 4:42 j 2:12: ðhÞ z1 z2 ¼ 1 þ j 2; ðiÞ z4
(10.6)
• Using (10.6), the quotient of two complex numbers can be expressed as
¼
Example 10.1.
(10.7)
10.3 Conjugate of a Complex Number The conjugate of a complex number z is obtained by changing the sign of the imaginary part of the number. For example, the conjugate of 3 þ j4 is 3 j4. The conjugate of a complex number z is denoted by z :
10.5 Arithmetic in a Complex Plane
347
conjugate of z ¼ z ¼ Refzg j Imfzg:
(10.8)
The conjugate of a real number is the number itself. Conjugation is distributive over addition, multiplication, and division: ðz1 þ z2 Þ ¼ z1 þ z2 ; ðz1 z2 Þ z1 z1 ¼ z1 z 2 ; ¼ : z2 z2
(10.10)
10.4 Magnitude of a Complex Number The magnitude of a complex number z is denoted by jzj and is defined by jzj ¼
qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi Re2 fzg þ Im2 fzg;
that is, if z ¼ a þ j b, then jzj ¼
(10.12)
The magnitude of the product or quotient of two complex numbers is the product or quotient of the magnitudes: z1 jz1 j : (10.13) jz1 z2 j ¼ jz1 jjz2 j; ¼ z2 jz2 j
(10.9)
As a result, it is unnecessary to reduce an expression to the form a þ jb in order to obtain the conjugate. All that is necessary is to replace j by –j wherever it appears in the expression. For example, the conjugate of ð jÞ3 ð3 þ j4Þ=ð2 j6Þ2 is ðjÞ3 ð3 j4Þ=ð2 þ j6Þ2 . Note that this approach requires that all of the imaginary units (js) in the expression be visible; for example, the conjugate of j z is j z , not simply j z, if z is complex. The sum and difference of a complex number and its conjugate are of special importance because z þ z ¼ 2 Refzg; z z ¼ 2j Imfzg:
jz1 þ z2 þ þ zn j jz1 j þ jz2 j þ þ jzn j:
(10.11)
pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a2 þ b2 :
The product of a complex number and its conjugate is of special importance because it equals the square of the magnitude of the number. From (10.11), z z ¼ ða þ jbÞða jbÞ ¼ a2 þ b2 ¼ jzj2 :
(10.14)
This result can be used to rationalize the quotient of two complex numbers or expressions prior to performing the indicated division. From (10.14), z1 z1 z2 z1 z2 ¼ ¼ : z2 z2 z2 jz2 j2
(10.15)
It is easier to remember and apply the process expressed by (10.15) than it is to remember and use the formula (10.6). Exercise 10.3. Let z1 ¼ 3 þ j 4; z2 ¼ 1 j 2; z3 ¼ j 5; z4 ¼ 5 þ j: Verify each of the following: ðaÞ z1 z2 ¼ 5 þ j 10; ðbÞ jz1 z3 j ¼ 3:16; z1 z1 ðcÞ ¼ 0:28 þ j 0:96;ðdÞ ¼ 2:24; z1 z2 2 z1 z2 jz2 j ¼ 1: ðeÞ ¼ 0:085 þ j 0:177; ðf Þ z1 z4 ðz1 z2 Þ
10.5 Arithmetic in a Complex Plane Exercise 10.2. Show that if z is real, the right side of (10.11) reduces pffiffi to the absolute value of z. (Recall that denotes positive square root.) The magnitude of a complex number is a nonnegative real number. Therefore, the magnitudes of complex numbers can be ordered and expressions of the form jz1 j<jz2 j are meaningful. An important example is the (generalized) triangle inequality
Complex numbers can be placed in correspondence with points in a Cartesian plane called a complex plane. The coordinates (abscissa and ordinate) of a point in the plane are the real and imaginary parts, respectively, of the number represented by the point. The horizontal axis is called the real axis, often labeled Refzg and the vertical axis is called the imaginary axis, often labeled Imfzg: Figure 10.1. shows a complex plane in which several complex numbers
348
10 Complex Arithmetic and Algebra
number also may be expressed in polar form as rffy as illustrated in Fig. 10.3, where
Im (z) 3 + j4 −3 + j 3
r¼
j2 −4
Re (z) 3 − j2
−3 − j 3
Fig. 10.1 Complex numbers represented by points in a plane
(including one real number and one imaginary number) are represented. The complex number represented by a point is often written next to the point, as in Fig. 10.1; however, a point in a complex plane is a representation of the number, not the number itself. Again, both the abscissa and ordinate of a point representing a complex number are real numbers. Often, it is helpful to refer to graphical descriptions of arithmetic operations using a complex plane, as illustrated in Fig. 10.2. Figure 10.2(a) shows addition of two complex numbers, illustrating that complex numbers add like vectors (because the real and imaginary parts add separately, as do the components of a vector). Figure 10.2(b) shows negation and conjugation of a single complex number. Negation reflects a number through the origin and conjugation reflects a number in the horizontal (real) axis. Figure 10.2(c) shows multiplication of a complex number by various powers of the imaginary unit j, illustrating that multiplication by j rotates the number 90 counter-clockwise about the origin.
10.6 Polar Form of a Complex Number A complex number, when written as z ¼ a þ j b; is said to be expressed in rectangular form because the components of the number (real and imaginary parts) are the coordinates of the corresponding point (a, b) expressed in rectangular coordinates.2 A complex 2 What we call rectangular coordinates also are called cartesian coordinates and the rectangular form of a complex number also is called the cartesian form of the number.
pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a2 þ b 2 ;
y ¼ Tan1 ða; bÞ:
(10.16)
The function Tan1 ð Þ in (10.16) is the fourquadrant inverse tangent, defined by 8 tan1 ðb=aÞ; > > > < ðp=2Þ sign ðbÞ; Tan1 ða; bÞ ¼ > 0; > > : p þ tan1 ðb=aÞ;
if a>0; if a ¼ 0 and b 6¼ 0; if b ¼ 0 and a ¼ 0; if a<0: (10.17)
where tan1 ð Þ is the two-quadrant inverse tangent, defined as follows: If a ¼ tanðyÞ and p=2
10.7 Eulers Identity and Polar Arithmetic
349 Im (z)
Im (z)
jz
Im(z) z1 + z2
z1
z
z θ
z2
Re (z)
θ
θ
−z
z*
(a)
π 2
Re (z)
j 2 z = −z
(b)
z
π 2
π 2 π 2
Re (z)
j 3z = −jz
(c)
Fig. 10.2 Depiction of various operations in a complex plane
The relationships between the rectangular form a + jb and the polar form rffy of a complex number are summarized below: pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a þ jb ¼ a2 þ b2 ff Tan1 ða; bÞ ¼ rffy (10.18)
Im (z) z = a + jb = r∠q
b r
and rffy ¼ r cosðyÞ þ j r sinðyÞ:
θ
a
Fig. 10.3 Polar representation of a complex number in a complex plane
p 3p y ¼ Tan1 ð1;1Þ ¼ p þ tan1 ð1Þ ¼ p þ ¼ ; 4 4 which is correct, whereas the ordinary (two-quadrant) inverse tangent gives 1 p 1 ¼ tan1 ð1Þ ¼ ; tan 1 4 which is incorrect. From (10.16), the radial coordinate r of a complex number is just the magnitude of the number (defined above). The angular coordinate y is called the angle of the number; e.g., the magnitude and angle of 3 + j4 are 5 and 0.927, respectively.3,4 The symbol rffy is read as “r angle y.” The complex-plane representation of a complex number can be shown either as a point, as in Fig. 10.2, or as a vector (an arrow from the origin to the point), as in Fig. 10.3. Usually points are used to display numbers expressed in rectangular form and vectors are used to display numbers expressed in polar form. 3
(10.19)
Re (z)
Because we use radian measures exclusively, we do not attach the dimensionless unit rad to numerical values for angles. 4 Mathematicians refer to the magnitude as the modulus and to the angle as the argument.
Example 10.2. Express the number 3 þ j 4 in polar form. Solution: From (10.19), pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 32 þ 42 ¼ 5; Tan1 ð3; 4Þ ¼ 2:214 ) 3 þ j 4 ¼ 5ff2:214:
Exercise 10.4. Given z1 ¼ 3þj4; z2 ¼ 1j2; z3 ¼ j5; z4 ¼5þj; verify each of the following: ðaÞ z1 ¼ 5:00ff 0:93; ðbÞ z2 ¼ 2:24ff 1:11; ðcÞ z3 ¼ 5:00ff 1:57; ðdÞ z4 ¼ 5:10ff 2:94; ðeÞ z1 ¼ 5:00ff 0:93; ð f Þðz2 Þ1 ¼ 0:45ff 1:11:
10.7 Eulers Identity and Polar Arithmetic Replacing cosðyÞ and sinðyÞ by their series expansions on the right side of (10.20) and comparing the result with the series expansion for ejy leads to Eulers identity r ejy r cosðyÞ þ j r sinðyÞ:
(10.20)
350
10 Complex Arithmetic and Algebra Im(z) z = −1 + j
Im(z) z = −1 + j
1
1
θ Re (z)
−1
(a) correct angle: q = Tan−1(−1, 1) =
3p 4
θ
−1
Re(z)
? p (b) incorrect angle: q = tan−1 ( 1 ) = tan−1 (–1) = – –1 4
Fig. 10.4 In (a), the angle y is given correctly by the four-quadrant inverse tangent, in (b) the angle y is given incorrectly by the two-quadrant inverse tangent
Thus, rff y r e j y :
(10.21)
Equation (10.22) tells us how a polar representation rffy can be manipulated mathematically (e.g., in products and quotients) using the rules of ordinary arithmetic and algebra. It follows from (10.20), (10.21), and the law of exponents that ðr1 ffy1 Þðr2 ffy2 Þ ¼ r1 ejy1 r2 ejy2 ¼ r1 r2 ejðy1 þy2 Þ ¼ r1 r2 ffðy1 þ y2 Þ: (10.22) In words, the magnitude of the product is the product of the magnitudes and the angle of the product is the sum of the angles. It also follows from (10.20), (10.21), and the law of exponents that r1 ffy1 r1 e jy1 r1 jðy1 y2 Þ ¼ ¼ e r2 ffy2 r2 ejy2 r2 r1 ¼ ffðy1 y2 Þ: r2
z1 z2 ¼ ð2ffp=6Þð4ffp=4Þ ¼ ð2Þð4Þff
Example 10.3. Obtain the product z1 z2 and the quotient z1 =z2 ; where z1 ¼ 2ffp=6 and z2 ¼ 4ffp=4: Solution: From (10.23) and (10.24)
þ
p 4
6 5p ¼ 8ff ; 12 z1 2ffp=6 2 p p p ¼ ¼ ff ¼ 0:5ff : z2 4ffp=4 4 6 4 12
If the angle of a complex number is known exactly as the product of p and a rational number, the angle is often expressed that way, as in Example 10.3, above. Otherwise, angles are expressed using decimal numbers, as in Example 10.4, below.
Example 10.4. Perform the indicated operations and express the result (z) in both polar and rectangular form. z¼
(10.23)
In words, the magnitude of the quotient is the quotient of the magnitudes and the angle of the quotient is the angle of the numerator minus the angle of the denominator.
p
ð3 þ j 4Þ þ ð6 þ j 8Þ : 5 þ j 10
Solution: ð3 þ j 4Þ þ ð6 þ j 8Þ 9 þ j 12 ¼ 5 þ j 10 5 þ j 10 15ff 0:927 ffi 11:2ff1:11 ffi 1:34ff 0:180 ffi 1:34 cosð0:180Þ þ j 1:34 sinð0:180Þ
z¼
ffi 1:32 j 0:24:
10.9 Problems
351
Exercise 10.5. Let z1 ¼ 3 þ j 4; z2 ¼ 1 j 2; z3 ¼ j 5; z4 ¼ 5 þ j: Verify each of the following: z2 ðaÞ z1 z2 ¼ 11:2ff0:180; ðbÞ ¼ 0:447ff2:68; z3 1 ðcÞ z1 z3 z4 ¼ 4:90ff 2:70; ðdÞ
z 2 z4 jz3 j2 ¼ 1ff2:61; ðeÞ ¼ 0:981ff2:02: z4 z2 z1 z4
Nowadays, all but the simplest computations usually are done using a calculator (or computer) capable of doing complex arithmetic. When using such a calculator or computer for computations, it makes little difference whether we express complex numbers in rectangular or polar form. The choice often is dictated by ease of data entry or by the form in which the data are available. But when performing pencil-and-paper computations or symbolic manipulations of complex expressions, the rectangular form is generally most convenient for addition and subtraction and the polar form is best for multiplication and division. Furthermore, in a number of applications, the polar form is preferred for interpretative reasons.
following the operator ∡ is in general complex and can be dimensionless or dimensioned. Example 10.5. (a) ∡ð1 þ jÞ ¼ p=4 (b) ∡ð4ff0:6Þ ¼ 0:6 (c) 3ff∡j ¼ 3ffp=2 (d) ∡10 ej 0:8 ¼ 0:8; 3 j 4 ∡ 3 j 4 ¼ j 3 j 4j ðeÞ 2þj 2þj j2 þ jj ½∡ð3 j 4Þ ∡ð2 þ jÞ pffiffiffi ¼ 5 ff 1:39:
Exercise 10.6. Let z1 ¼ 3 þ j 4; z2 ¼ 1 j 2; z3 ¼ j 5; z4 ¼ 5 þ j: Verify each of the following: z1 z2 ¼ 1:39; ðbÞ ∡ðz2 Þ2 ¼ 2:21; ðaÞ ∡ z3 ðcÞ ∡ðz1 Þ4 ¼ 4∡z1 ðdraw a pictureÞ; ðdÞ ∡ðz1 z2 z3 z4 Þ ¼ 1:95; z2 ðeÞ ∡z1 þ ∡z1 ¼ 0; ðf Þ ∡ ¼ 2∡z2 ; z2 ðgÞ jz1 z2 jffð∡z3 Þ ¼ 11:2ff1:57:
10.8 The Symbols ∠ and ∡ The symbol ff denotes that the number (or expression) following is an angle; e.g., when expressing a number in polar form. In that context, the symbol ff serves as a separator between the magnitude and angle of a number denoted by r∠y, just as the comma serves as a separator between the x- and y-coordinates of a point denoted by (x, y). The symbol ∡ is an operator that means the angle of the number or expression that follows. For example, ff p=2 denotes an angle equal to p=2 radians (90 ) whereas ∡p=2 means the angle of the real number p=2; which equals zero. For z ¼ x þ j y; ∡z ¼ ∡ðx þ j yÞ ¼ Tan1 ðx; yÞ:
(10.24)
A value or expression following the symbol ff is a real angle expressed in radians. A value or expression
10.9 Problems
Section 10.5 is prerequisite to the following problems. P 10.1 Find the real and imaginary parts, the magnitude, the conjugate, and the reciprocal of each of the following numbers. pffiffiffiffiffiffiffi (a) j, (b) 3 j 2; (c) 4, (d) 5 j2 ; (e) j3 ; pffiffiffiffiffiffiffiffiffi (f) ð2 jÞ1 ; (g) 1 j 3; (h) 3j þ 12 16; (i) jð2 j5Þ; (j) 1 þ 2j 3j2 þ 4j3 6j4 ; (k)
6 8: 2j
352
10 Complex Arithmetic and Algebra
P 10.2 Reduce each of the following to the form a þ j b: Represent each result as a point in a complex plane. 120 j 240 ; (a) ð3 þ j 2Þð5 j 6Þ; (b) ð2 j 3Þ3 ; (c) 3 þ j4 4 þ j2 (d) ð1 jÞ þ 3 þ j4 : 1þj P 10.3 Let z1 ¼ 1 j; z2 ¼ 2 þ j 3; z3 ¼ 6j: Reduce each of the following to the form a þ j b: Represent each result as a point in a complex plane. z3 z1 z1 z1 z2 ðz1 z2 z3 Þ (a) ; (c) ; (d) ; ; (b) 10 10 z jz j 2
2
z1 z2 þ z1 z2 z1 z2 z1 z2 (e) ; (f) ; (g) z2 1 ; 10 z3 ðz1 þ z3 Þz2 z1 þ z3 z3 ; (j) ; ; (i) (h) 10 z 2 z1 z1 þ z2 ðz1 z3 Þðz1 þ z3 Þ z1 þ z2 þ z3 ; (l) : (k) 3z2 z1 ðz1 þ z2 þ z3 Þ
P 10.4 Let z1 ¼ 1 j; z2 ¼ 1 þ j; z3 ¼ 2j: Depict each of the following operations in a complex plane. (a) z1 þ z2 ; (b) z1 z2 ; (c) z1 þ z3 ; (d) z2 þ z3 ; (e) z1 þ z2 þ z3 ; (i) ðz1 þ z2 Þz3 ; (j)
(f) z1 z3 ;
(g) z2 z3 ;
(h) z3 3 ;
z2 z1 : z3
Section 10.7 is prerequisite to the following problems. P 10.5 Refer to Problem P 10.1. Express each number given there in polar form. P 10.6 Under what conditions on a and b do the fourquadrant inverse tangent and the two-quadrant inverse tangent give the same number for the angle of a þ j b?
P 10.7 Use both the four-quadrant inverse tangent and the two-quadrant inverse tangent to obtain the angle of each of the numbers given in Problem P 10.1 If the angles differ, explain why. P 10.8 Let z1 ¼ 1 j; z2 ¼ 2 þ j 3; z3 ¼ 6j: Convert each to polar form. Then perform each of the following operations using polar arithmetic and convert the result back to rectangular form. z3 z1 z1 (b) z1 z2 (c) ðz1 z2 z3 Þ (d) (e) z2 1 (f) z1 5 (a) jz2 j z2 3 2 z2 z1 z3 (g) z3 (h) z1 ðz1 2 z2 z3 Þ P 10.9 Refer to Problem P 10.1. Express each number given there in the form r ej y : Section 10.8 is prerequisite to the following problems. P 10.10 Let z1 ¼ 1 j; z2 ¼ 2 þ j 3; z3 ¼ 6j: Find each of the following, doing as little arithmetic as possible. z1 (a) ∡ ; (b) ∡ðz1 z3 Þ; (c) ∡ðz2 z3 Þ; (d) ∡ðz3 3 Þ; z2 z2 z1 (e) ∡ðz1 z2 z3 Þ; (f) ∡ ; (g) ð∡z2 Þ þ ð∡z1 Þ; z3 (h) ð∡z3 Þ2 : P 10.11 Let z1 ¼ 1 j; z2 ¼ 2 þ j 3; z3 ¼ 6j: Find each of the following, doing as little arithmetic as possible. z1 (a) ; (b) jz1 z3 j; (c) jz2 z3 j; (d) z33 ; (e) jz1 z2 z3 j; z2 z2 z1 ; (g) jz2 j þ jz3 j; (h) z2 2 : (f) z3
Chapter 11
Transient Analysis
(
0; t 0; 1; t > 0:
Transient analysis examines the transition of a current or voltage in a circuit from one steady state to another after an abrupt change in excitation or circuit structure. Questions addressed by transient analysis include:
uðtÞ ¼
• How long does the transition take? Is the response quick or sluggish? • What is the new steady state after the transition is complete? • Is the transition smooth, or are there overshoots and undershoots before steady state is achieved? • If there are overshoots or undershoots, how large are they? Might they damage some sensitive component? • What circuit parameters influence the transition and new steady state, and in what ways?
Example 11.1. A voltage given by
In circuits terminology, the order of a differential equation relating a response (output) to an excitation (input) is the order of the highest derivative of the response, and the order of a circuit is the order of the differential equation relating the excitation and response of interest. In this chapter, we limit our discussion to circuits for which excitations and responses are related by first-order or second-order differential equations. As noted above, transient analysis deals in part with responses to excitations that change abruptly from one value to another. The unit step function defined in the next section facilitates describing such excitations.
Example 11.2. The voltage
( vðtÞ ¼
(11.1)
0; t 0; V0 ; t > 0;
can be expressed compactly as vðtÞ ¼ V0 uðtÞ:
( vðtÞ ¼
V1 ; t 0; V2 ; t > 0;
can be expressed compactly as vðtÞ ¼ V1 þ ðV2 V1Þ uðtÞ:
Exercise 11.1. Use unit step functions to express
11.1 Unit Step Function Sudden changes (jump discontinuities) in a current or voltage can be described compactly using the unit step function, defined by
8 > < I 0 ; t t0 ; iðtÞ ¼ I1 ; t0 < t t1 ; > : I2 ; t > t1
T.H. Glisson, Introduction to Circuit Analysis and Design, DOI 10.1007/978-90-481-9443-8_11, # Springer ScienceþBusiness Media B.V. 2011
353
354
11 Transient Analysis
Thus y0 ðt0 Þ denotes the first derivative with respect to time of a current or voltage yðtÞ, evaluated at t ¼ t0 :
11.2 Notation In transient analysis, it is often necessary to specify times that differ only infinitesimally from each other; e.g., at instants just before and just after an abrupt change in excitation. As a reminder, we denote the instants infinitesimally before and after a time t ¼ t0 þ by t ¼ t 0 and t ¼ t0 , respectively. For example, if a voltage v is defined by vðtÞ ¼ V1 uðtÞ; then vð0 Þ ¼ 0; vð0þ Þ ¼ V1 : For any time t0 , the instants t ¼ t 0 , t ¼ t0 , and t ¼ tþ are only infinitesimally different, so any contin0 uous function has the same value at all three times. For example, þ t t t 0 0 exp ¼ exp ¼ exp 0 t t t and þ sin o t 0 ¼ sinðo t0 Þ ¼ sin o t0 : We attach units only to non-zero, finite times, e.g., t ¼ 5 ms, but t ¼ 0 (no unit) and t ! 1 (no unit). If t ¼ 0 or t ! 1, then t is zero or infinite whether expressed in seconds, microseconds, minutes, or years, so in those cases units are irrelevant. For the same reason, there is no need to associate a unit with t ¼ 0 or t ¼ 0þ . Similarly, we do not attach units to any current, voltage, power, energy, or charge that equals zero, is infinitesimal, or approaches infinity. For example, if a voltage vðtÞ equals zero at time t0 , we write vðt0 Þ ¼ 0, not vðt0 Þ ¼ 0 V.1 We often use a prime to denote the first derivative with respect to time of a current or voltage yðtÞ, as in y0 ¼ y0 ðtÞ ¼
1
dy : dt
Software packages that provide for dimensioned variables require consistent use of units (if used at all), even for zero values. Also, note that we require a unit for zero temperature, because zero Celsius, zero Fahrenheit, and zero Kelvin are all different.
y0 ðt0 Þ ¼
dy : dt t¼t0
(11.2)
The notation in (11.2) means differentiate first, then replace t with t0 . If you do the reverse, the result will always be zero. We also need a concise notation for the value of a current or voltage in the distant future; for example, a long time after an abrupt change in excitation. We use the notation vð1Þ and ið1Þ as shorthand for the associated limits; i.e., vð1Þ ¼ lim vðtÞ;
ið1Þ ¼ lim iðtÞ;
0
0
t!1
0
t!1
v ð1Þ ¼ lim v ðtÞ; i ð1Þ ¼ lim i0 ðtÞ: t!1
t!1
(11.3)
Mathematicians might object to this notation because infinity is not a specific value that can be substituted for a variable in a function. Nonetheless, the notation is compact and serves us well.
11.3 Initial Conditions For the present, we limit our attention to obtaining and interpreting responses of stable first-order and secondorder linear circuits to step excitations – excitations that change abruptly at t¼0. Solving the differential equations governing such responses requires knowing the response and (for second-order circuits) the first derivative of the response at t¼0þ. Such initial conditions are obtained using Kirchhoff’s laws and the fact that currents through inductors and voltages across capacitors are continuous. A step excitation, such as vS ðtÞ ¼ VS uðtÞ, is zero for all t < 0 and equals a non-zero constant VS for all t > 0. A circuit is in dc steady state if all currents and voltages in the circuit are constant. In particular, voltages across capacitors and currents through inductors are constant in dc steady state. Generally, a circuit excited by a step current or voltage is in dc steady state before t ¼ 0.
11.4 First-Order Circuits
355
It follows from the terminal characteristics
RS
+
+
dv i ¼ C ¼ Cv0 ; dt
di v ¼ L ¼ Li0 ; dt
–
RS
R
i
vC
C
VS
–
+
L
–
iL
+
vC
VS
–
(a)
that if a circuit is in dc steady state, the current through each capacitor and the voltage across each inductor equals zero. Before finding currents and voltages in a circuit in dc steady state, we may replace each capacitor by an open circuit and each inductor by a short circuit. A circuit in dc steady state is essentially resistive.
iL ¼ i ¼
VS RVS ; vC ¼ R iL ¼ : RS þ R RS þ R
iL
(b)
Fig. 11.1 See Example 11.3
C1 R1
R2
R2
+
+ –
Example 11.3. The circuit in Fig. 11.1(a) is in dc steady state. Obtain expressions for the current i and the voltage vC . Solution: Because the circuit is in dc steady state, we may replace the capacitor by an open circuit and the inductor by a short circuit. This gives the circuit in Fig. 11.1(b), where
R
i
V0
V –
C2
L I
Fig. 11.2 See Exercise 11.2
describe step responses of first- and second-order circuits.
11.4 First-Order Circuits A first-order circuit is one for which excitation and response are related by a first-order differential equation expressed in standard form as
Exercise 11.2. The circuit in Fig. 11.2 is in dc steady state. (a) Obtain expressions for the current I and the voltage V. (b) Obtain expressions for the voltages across the capacitors and the current through the inductor. Indicate assumed current directions and voltage polarities on the circuit diagram. Response to a step excitation, called a step response, often is used to describe or specify performance, especially in applications where excitations exhibit repeated abrupt changes in amplitude. The response of a linear stable circuit to a step excitation consists of a transient component, which eventually vanishes, and a steadystate component, which remains after the transient has vanished. A step response might be described in terms of attributes such as rise time, overshoot, settling time, and steady-state amplitude. In short, step response is often used to address questions such as those posed at the beginning of this chapter. The next two sections
t
dy dx þ y ¼ b0 x þ b 1 ; dt dt
(11.4)
where xðtÞ is an excitation and yðtÞ is the corresponding response. For a step excitation xðtÞ ¼ X0 uðtÞ and for t > 0, the differential equation (11.4) becomes t
dy þ y ¼ b0 X0 ; t > 0: dt
(11.5)
The coefficient of the response y in (11.5) is unity, so every term in the standard-form differential equation has the dimension of the response. It follows that SIðtÞ ¼ s; SIðb0 Þ ¼
SIð yÞ : SIðX0 Þ
(11.6)
We treated such circuits in Chapters 8 and 9, where we showed that the response is given (for t > 0) by
356
11 Transient Analysis
t yðtÞ ¼ yð1Þ ½yð1Þ yð0þ Þ exp : t
(11.7)
Example 11.4. Refer to Fig. 11.3, where vS ¼ V0 uðtÞ. (a) Obtain a standard-form differential equation relating the voltage vC (the response) to the excitation for t > 0. (b) Obtain expressions for vC ð0 Þ and vC ð0þ Þ. (c) Obtain an expression for vC ðtÞ. Solution: (a) Applying Kirchhoff’s current law to the circuit gives v C V0 dvC þC ¼ 0; t > 0: R dt
y ¼ yf þ yu :
(11.8) Y0 ¼ b0 X0 ;
dvC þ vC ¼ V0 ; t > 0; t ¼ RC: dt
yf ¼ b0 X 0
t
Although we know the form of the response of a first-order circuit to a step excitation, we wish to derive that solution again, but by a different method; one that is applicable to second- and higher-order differential equations. If you have had or are taking a R +
Fig. 11.3 See Example 11.4
C
(11.12)
The unforced response is the general solution to the homogeneous equation
(11.9)
t vC ðtÞ ¼ vC ð1Þ ½vC ð1Þ vC ð0þ Þ exp t h t i ; t > 0; t ¼ RC: ¼ V0 1 exp t
+ –
(11.11)
so the forced response is given by
(b) The source vS is essentially a short circuit for t < 0, so vC ð0 Þ ¼ 0. The voltage across a capacitor cannot change instantaneously, so vC ð0þ Þ ¼ vC ð0 Þ ¼ 0. For t > 5t, the circuit is once again in dc steady state, with vC ð1Þ ¼ V0 . (c) Thus, vC ðtÞ ¼ 0 for t < 0 and
vS
(11.10)
The forced response of a stable linear circuit has the form of the excitation. For step excitation, the forced response is a constant because the excitation is a constant (for t > 0). Thus yf ¼ Y0 , where Y0 is a constant. Substituting this solution for y in (11.5) gives
Multiplying by the resistance R (to make the coefficient of vC equal to unity) and rearranging terms gives the standard-form differential equation t
course in differential equations, you might be familiar with this method, called the method of undetermined coefficients, which proceeds as follows: The complete solution to (11.5) is called the complete response or simply the response of the associated circuit. The response is the sum of the forced response yf and the unforced response yu :2
vC –
dyu þ yu ¼ 0: dt
(11.13)
The unforced response must contain one arbitrary constant that cannot be determined from (11.13) alone. As we show below, the arbitrary constant can be determined from the initial value of the response, denoted by yð0þ Þ. According to (11.13), a linear combination of the unforced response and its derivative (with respect to time) have the same time dependence. Otherwise the left side could not be zero for all time. The exponential function has this property, so we are led to try yu ¼ Yes t in (11.13), where Y and s are constants, as yet unknown.3 We obtain
2
Mathematicians call the forced response the particular integral and the unforced response the complementary solution (or function). The names used here are more appropriate (and suggestive) for physical problems. 3 Note that s (italic) is a variable and s (roman) is a unit (second). In written work, you might want to distinguish the unit s from the variable s by underlining the former.
11.4 First-Order Circuits
t
357
dðYes t Þ þ Yes t ¼ tYses t þ Yes t dt ¼ Yes t ðts þ 1Þ ¼ 0:
C R2
(11.14) R1
st
The exponential e cannot be zero for any finite value of s. We require Y 6¼ 0 because Y ¼ 0 gives the trivial solution yu ¼ 0, which contains no arbitrary constants and can be ignored. Thus the function Y es t satisfies the differential equation (11.31) if the constant s satisfies the characteristic equation ts þ 1 ¼ 0;
(11.15)
whose solution is the characteristic root 1 s¼ : t
(11.16)
The parameter t is the time constant for the response. The unforced response is given by yu ¼ Yes t ¼ Yet=t ;
(11.19)
Thus (compare with (11.7)) yðtÞ ¼ b0 X0 þ ½yð0þ Þ b0 X0 et=t ; t > 0: (11.20)
vn V0 vn vo þ R1 R2 d ðvn vo Þ þC ¼ 0: dt
(11.21)
From the circuit diagram vp ¼ 0. The op amp is ideal, so vn ¼ vp ) vn ¼ 0. Equation (11.21) reduces to dvo R2 V0 þ vo ¼ ; t > 0; dt R1
(11.22)
which is (11.5), with y ¼ vo , X0 ¼ V0 , b0 ¼ R2 =R1 , and t ¼ R2 C. The excitation equals zero for all t 0, and the capacitor is shunted by a resistor, so vo ð0 Þ ¼ 0. Because vn ¼ 0, the voltage vo is the voltage across the capacitor, so vo must be continuous. It follows that vo ð0þ Þ ¼ vo ð0 Þ ¼ 0:
A response given by (11.20) consists of an unforced component ½yð0þ Þ b0 X0 et=t and a forced component b0 X0 . In a stable circuit, the unforced component
RL
Example 11.5. Refer to Fig. 11.4, where the op amp is ideal and v0 ðtÞ ¼ V0 uðtÞ. Obtain an expression for the voltage vo ðtÞ. Identify the transient and steady-state components of the response. Solution: No current enters the n terminal. Kirchhoff’s current law gives (for t > 0)
R2 C
yð0þ Þ ¼ b0 X0 þ Y ) Y ¼ yð0þ Þ b0 X0 :
vo
o
eventually vanishes, and only the forced component remains. Thus the forced component is the steady-state response and the unforced component is the transient response, called the transient, for short.
(11.18)
where
+ –
–
p +
Fig. 11.4 See Example 11.5
(11.17)
where Y is an arbitrary constant having the dimension of the response and t is the time constant. From (11.10), (11.12), and (11.17), the complete response is given by yðtÞ ¼ b0 X0 þ Yest ; t > 0;
v0
n
From (11.20)
(11.23)
358
11 Transient Analysis +
9 8 > t < 0; > = < 0; v¼ ; R 2 > ; : V0 1 et=t ; t > 0 > R1 t ¼ R2 C:
– C
i
vC
R2 R2 V0 ; vu ¼ V0 et=t ; t > 0: R1 R1
The time constant of a first-order circuit is discussed at length in Chapters 8 and 9. As a reminder, the time constant t is a measure of the time required for the transient component to vanish (for steady state to be achieved). For t ¼ 5t, e5 ffi 0:00674 and the magnitude of the transient component is less than 1% of its initial value. Often, 5t is taken as the duration of the transient (as the time required for steady state to be achieved). For t > 0, a step excitation x ¼ X0 uðtÞ is a constant (dc) current or voltage given by x ¼ X0 . After the transient vanishes (for practical purposes), the response of a linear stable circuit to such a step excitation is also a constant (dc) current or voltage, given by y ¼ b0 X0 . Thus the magnitude of the parameter b0 is called the dc gain of the circuit. The time constant t and dc gain jb0 j are constant functions of circuit parameters. Two distinct procedures are treated in the discussion above: One addresses how to obtain an expression for the response of a first-order circuit to a step excitation. If that is the objective (11.7) usually provides the most direct approach. The other addresses how one can solve a differential equation using the assumed solution Y expðs tÞ. That procedure is generalized to second-order differential equations in the sequel. Equation (11.7) can be applied to any of the responses labeled in either of the circuits in Fig. 11.5. Example 11.6. Obtain an expression for the current iðtÞ in Fig. 11.5(b). Solution: The excitation (the independent source) is zero for t < 0, so ið0 Þ ¼ 0. The
– +
R
V0 u (t) +–
L
i
–
(a) RC circuit
(11.24)
vR
+ +
R
V0 u(t) +–
The steady-state component is the forced response vf and the transient component is the unforced response vu : vf ¼
vR
–
(b) RL circuit
Fig. 11.5 First-order RC and RL series circuits
current though an inductor must be continuous, so ið0þ Þ ¼ ið0 Þ ¼ 0. The time constant is t ¼ L=R. For t t, the circuit is in dc steady state, the inductor is effectively a short circuit, so ið1Þ ¼ V0 =R. Thus, from (11.7), iðtÞ ¼ 0 for t < 0 and t iðtÞ ¼ ið1Þ ½ið1Þ ið0þ Þ exp t t i V0 h 1 exp ; t > 0: ¼ R t The complete response would normally be written using a unit step function as iðtÞ ¼
t i V0 h 1 exp uðtÞ; R t
t¼
vL
L : R
Example 11.7. Obtain an expression for the voltage vR ðtÞ in Fig. 11.5(a). Solution: The voltage vR ðtÞ appears across a resistor (not a capacitor), and need not be continuous. But the voltage vC ðtÞ must be continuous, so vC ð0þ Þ ¼ 0. Kirchhoff’s current law gives, for t ¼ 0þ , vR ð0þ Þ þ vC ð0þ Þ ¼ V0 ) vR ð0þ Þ ¼ V0 : The time constant is t ¼ RC. For t t, the circuit is in dc steady state, the capacitor is effectively an open circuit, so ið1Þ ¼ 0, which implies (Ohm’s law) vR ð1Þ ¼ 0. From (11.7) t vR ðtÞ ¼ vR ð1Þ ½vR ð1Þ vR ð0þ Þ exp t t ¼ V0 exp ; t > 0: t
11.4 First-Order Circuits
359 RS + R1
R1 IS u(t)
RS
i
i
R2
+ C
vC
+
+ V u(t) – S
R2
C
–
vS
+
RS
+ –
C
Ri
vC
v1 –
+ gv1
Ro
RL
–
(a)
(b)
Fig. 11.7 See Example 11.9
Fig. 11.6 See Example 11.8
or Thus t iðtÞ ¼ V0 exp uðtÞ; t
vC ðtÞ ¼ t ¼ RC:
h t i R2 RS IS 1 exp uðtÞ; R1 þ R2 þ RS t
so vC ðtÞ R2 h t i RS IS ¼ 1 exp uðtÞ: R1 þ R2 þ RS t
iðtÞ ¼ Any (non-pathological) circuit comprising only resistors and one capacitor or one inductor can be reduced using The´venin’s theorem to one of the circuits in Fig. 11.5. A circuit equivalent to the circuit in Fig. 11.5(a) at the terminals of the capacitor is called a first-order RC circuit. One equivalent to the circuit in Fig. 11.5(b) at the terminals of the inductor is called a first-order RL circuit. Example 11.8. Refer to Fig. 11.6(a). Obtain an expression for the current iðtÞ. Solution: We first obtain an expression for the voltage vC ðtÞ and subsequently use Ohm’s law to obtain an expression for the current iðtÞ. We apply a source transformation to obtain the circuit in Fig. 11.6(b), where VS ¼ IS RS . The The´venin equivalent for the rest of the circuit at the terminals of the capacitor has the form of the circuit in Fig. 11.5(a), where R ¼ ðRS þ R1 ÞkR2 . The time constant is given by t ¼ RC ¼ ½ðRS þ R1 ÞkR2 C: By inspection, vC ð0þ Þ ¼ 0 and R2 VS v C ð1Þ ¼ R1 þ R2 þ RS From (11.7) t vC ðtÞ ¼ vC ð1Þ ½vC ð1Þ vC ð0þ Þexp t h t i R2 VS 1 exp ; t>0 ¼ t R1 þ R2 þ RS
Example 11.9. See Fig. 11.7. (a) Obtain an expression for the voltage vL ðtÞ, where vS ¼ V0 uðtÞ. (b) Let RS ¼ 50 O, C ¼ 22nF, Ri ¼ 1MO, g ¼ 1mS, Ro ¼ 10kO, RL ¼ 5kO, and vS ¼ V0 uðtÞ, with V0 ¼ 5V. Construct a graph of the voltage vL versus time for t t 5t. Solution: (a) The output subcircuit is resistive and has no effect on currents and voltages in the input subcircuit, so the time constant is determined by the elements in the input subcircuit. The The´venin equivalent resistance at the terminals of the capacitor is RT ¼ RS k Ri , so the time constant is given by t ¼ ðRS kRi ÞC: By inspection, vL ðtÞ ¼ g v1 ðtÞ ðRo kRL Þ:
vL –
(11.25)
The voltage vS equals zero for t 0 (the source is a short circuit for t 0), so v1 ðtÞ ¼ 0 for t < 0. The voltage v1 ðtÞ appears across a capacitor and must be continuous. Thus v1 ð0þ Þ ¼ 0. For t t, the circuit is in dc steady state, the capacitor is effectively an open circuit, and
360
11 Transient Analysis
v 1 ð1Þ ¼
Ri V0 : Ri þ RS
R2 ¼ R4 ¼ 10kO, and V0 ¼ 5V. Construct a graph of the voltage vL versus time for t t 5t, where t is the circuit time constant.
From (11.7) t v1 ðtÞ ¼ v1 ð1Þ ½v1 ð1Þ v1 ð0þ Þexp t t i Ri V0 h ; t>0: ¼ 1 exp Ri þ RS t
11.5 Second-Order Circuits
Thus, from (11.25), and incorporating a unit step to express the voltage for all time, we have
A second-order circuit is one for which excitation and response are related by a second-order differential equation expressed in standard form as
g Ri V0 Ro RL Ri þ RS Ro þ RL h t i 1 exp uðtÞ: t
v L ðtÞ ¼
a2
d2 y dy dx d2 x þ a x þ b ; (11.26) þ y ¼ b þ b 1 0 1 2 dt2 dt dt dt2
where xðtÞ is an excitation and yðtÞ is the corresponding response. For a step excitation xðtÞ ¼ X0 uðtÞ and for t > 0, (11.26) becomes
(b) For the given parameter values, we find g Ri V0 Ro RL ffi 16:7 V; Ri þ RS Ro þ RL RS Ri t¼ C ffi 1:10 ms: R S þ Ri
a2
d2 y dy þ a1 þ y ¼ b0 X0 ; t > 0: dt2 dt
(11.27)
The coefficients a1 ; a2 ; b0 are constant functions of circuit parameters. The coefficient of y is unity, so every term in (11.27) has the dimension of the response. It follows that
Figure 11.8 shows a graph of the response.
Exercise 11.3. In Fig. 11.9, vS ¼ V0 uðtÞ and the response of interest is the voltage vL . (a) Obtain an expression for the voltage vL ðtÞ. (b) Let RS ¼ 50 O, C ¼ 15 nF, R1 ¼ R3 ¼ 1MO, m1 ¼ 15, m2 ¼ 25, RL ¼ 2:2kO,
SIða2 Þ ¼ s2 ; SIða1 Þ ¼ s; SIðb0 Þ ¼
SIð yÞ : (11.28) SIðX0 Þ
Example 11.10. In Fig. 11.10, vS ðtÞ ¼ V0 uðtÞ. Obtain the standard-form differential
5 0
RS
vL (V)
vS R1 v1 –
+ –
+ –
R2 m1v1
+ R3
v2
C
–
+ –
+
–5
R4 m2v2
+
vL
RL
–
–10
Fig. 11.9 See Exercise 11.3 –15
R –20 2
1
0
1
2 t (μs)
3
4
5
6
vS
i
+ –
L C
Fig. 11.8 See Example 11.9
Fig. 11.10 See Example 11.10
11.5 Second-Order Circuits
361
equation relating the current i to the voltage vS for t > 0. Solution: By Kirchhoff’s voltage law ð di 1 t iðt0 Þdt0 ¼ V0 ; t > 0: Ri þ L þ dt C 1 Differentiating once with respect to time and rearranging terms gives LC
d2i di þ RC þ i ¼ 0; t > 0; 2 dt dt
which has the form (11.26) with y ¼ i, a2 ¼ LC, a1 ¼ RC, and b0 ¼ 0. As an exercise, show that the SI units of the coefficients a1 ; a2 are as specified by (11.28).
Exercise 11.4. In Fig. 11.11, vS ðtÞ ¼ V0 uðtÞ. Obtain the standard-form differential equation relating the voltage vC to the voltage vS for t > 0. Show that the SI units of the coefficients a1 ; a2 ; b0 are as specified by (11.28). We use the method of undetermined coefficients to obtain the solution to (11.27). The complete solution yðtÞ to (11.27) is the complete response, and is the sum of the forced response yf ðtÞ and the unforced response yu ðtÞ. Thus yðtÞ ¼ yf ðtÞ þ yu ðtÞ:
(11.29)
The forced response has the form of the excitation, so the forced response is constant. If we let yðtÞ ¼ Y0 (a constant) in (11.27), we obtain Y0 ¼ b0 X0 . Therefore the forced response is given by yf ðtÞ ¼ b0 X0 uðtÞ:
+ –
R
vS
The unforced response yu ðtÞ is the solution to the homogeneous equation a2
d 2 yu dyu þ yu ¼ 0 þ a1 dt2 dt
(11.31)
obtained from (11.27) by setting the excitation X0 to zero. Any solution to (11.31) is also a solution to (11.27) because b0 X0 þ 0 ¼ b0 X0 . If yu1 and yu2 are any two solutions to (11.31), then yu ¼ Y1 yu1 þ Y2 yu2 , where Y1 and Y2 are arbitrary constants, is also a solution, as you can show by substitution. The general solution to (11.31) must reduce (11.31) to an identity and must contain exactly two independent arbitrary constants. (The trivial solution yu ¼ 0 meets the first requirement, but not the second.) In this context, arbitrary means that yu ¼ Y1 yu1 þ Y2 yu2 satisfies (11.31) for any values whatever of the constants Y1 ; Y2 and independent means that yu ¼ Y1 yu1 þ Y2 yu2 cannot be reduced to the form yu ¼ Y yu , where the two arbitrary constants are reduced to a single constant. According to (11.31), a linear combination of the unforced response yu ðtÞ and its first two time derivatives is identically zero (for all time). That can be true only if yu ðtÞ and its first two time derivatives have exactly the same time dependence.4 A function having that property is the exponential function Y es t , where Y and s are constants. Substituting Y es t for yu in (11.31) yields a2 s2 Y es t þ a1 s Y es t þ Y es t ¼ a2 s2 þ a1 s þ 1 Y es t ¼ 0:
(11.32)
The exponential es t cannot be zero for any finite value of s. We assume Y 6¼ 0 because Y ¼ 0 yields the trivial solution, which contains no arbitrary constants and can be ignored. Thus the function Y es t satisfies the differential equation (11.31) if the constant s satisfies the characteristic equation
(11.30)
a2 s2 þ a1 s þ 1 ¼ 0:
(11.33)
+ L
C
vC –
Fig. 11.11 See Exercise 11.4
4
The sum of functions having different time dependences cannot be identically zero (cannot equal zero for all time); e.g., a sinusoidal function of time cannot cancel a real exponential function of time.
362
11 Transient Analysis
(current or voltage) and the SI unit of Y2 is that of the response divided by time; e.g. Vs1 or As1 . The complete response is the sum of the forced response given by (11.30) and the unforced response given by (11.35):
The characteristic roots are given by pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a21 4a2 ; 2a2 pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a1 a21 4a2 s2 ¼ : 2a2 s1 ¼
a1 þ
(11.34) (
The SI units of the differential equation coefficients are SIða2 Þ ¼ s2 and SIða1 Þ ¼ s, so SIðs1 Þ ¼ SIðs2 Þ ¼ s1 .5 Because (11.33) is satisfied by either characteristic root, the differential equation (11.31) is satisfied by Y1 es1 t and by Y2 es2 t , where the constants Y1 ; Y2 are arbitrary. Thus yu ðtÞ ¼ Y1 es1 t þ Y2 es2 t
(11.35)
also satisfies (11.31). If the arbitrary constants Y1 and Y2 are independent, then (11.35) is the general solution to (11.31). But if a21 4a2 ¼ 0, then from (11.34), s1 ¼ s2 ¼
a1 ; 2a2
(11.36)
and the right side of (11.35) reduces to Y1 es1 t þ Y2 es2 t ¼ ðY1 þ Y2 Þes1 t ¼ Yes1 t ; which contains only one arbitrary constant ðY Þ and cannot be the general solution. In that case, the general solution has the form yu ðtÞ ¼ ðY1 þ Y2 tÞes1 t as you can show by substitution. The general solution to (11.31) (the unforced response) is given by ( yu ðtÞ ¼ uðtÞ
Y1 es1 t þ Y2 es2 t ; a21 4a2 6¼ 0; ðY1 þ Y2 tÞes1 t ; a21 4a2 ¼ 0;
b0 X0 þ Y1 es1 t þ Y2 es2 t ; a21 4a2 6¼ 0; b0 X0 þ ðY1 þ Y2 tÞes1 t ; a21 4a2 ¼ 0: (11.38)
A response given by (11.38) consists of an unforced component and a forced component b0 X0 uðtÞ. In a stable circuit, the unforced component eventually vanishes, and only the forced component remains. Thus the forced component is the steady-state response and the unforced component is the transient response, called the transient, for short. After t ¼ 0, a step excitation x ¼ X0 uðtÞ is a constant (dc) current or voltage given by x ¼ X0 . After the transient vanishes (for practical purposes), the associated circuit is in dc steady state, with y ¼ b0 X0 . The magnitude of the parameter b0 is called the dc gain of the circuit. The function y given by (11.38) satisfies the differential equation (11.26), regardless of the values of the constants Y1 ; Y2 . In any particular physical problem, the values of the constants Y1 ; Y2 are determined by the initial values denoted by y0 and y00 , given by þ
y0 ¼ yð0 Þ;
Be aware that s (italic) is a variable and s (roman) is a unit. This usage, which is almost universal, is doubly unfortunate because the unit of s is s. In written work, you should underline the unit s to avoid confusion.
y00
dyðtÞ ¼ y ð0 Þ ¼ : dt t¼0þ 0
þ
(11.39)
The initial values are obtained from the initial state of the circuit as follows. From (11.38), (
(11.37)
where s1 and s2 are given by (11.34) and Y1 and Y2 are arbitrary constants. If a21 4a2 6¼ 0, the SI unit of both Y1 and Y2 is that of the response (current or voltage). If a21 4a2 ¼ 0, the SI unit of Y1 is that of the response 5
yðtÞ ¼ uðtÞ
þ
y0 ¼ yð 0 Þ ¼
b0 X0 þ Y1 þ Y2 ; a21 4a2 6¼ 0; b0 X0 þ Y1 ; a21 4a2 ¼ 0; (11.40)
and y00 ¼ y0 ð0þ Þ ( s1 Y1 þ s2 Y2 ; a21 4a2 6¼ 0; ¼ s1 Y1 þ Y2 ; a21 4a2 ¼ 0:
(11.41)
11.5 Second-Order Circuits
363
Equations (11.40) and (11.41) yield 8 0 < s2 ðy0 b0 X0 Þ y0 ; a2 4a 6¼ 0 ðs 6¼ s Þ; 2 1 2 1 s2 s1 Y1 ¼ : y0 b0 X0 ; a21 4a2 ¼ 0 ðs1 ¼ s2 Þ; 8 0 < s1 ðy0 b0 X0 Þ y0 ; a2 4a 6¼ 0 ðs 6¼ s Þ; 2 1 2 1 s2 s1 ; Y2 ¼ : 0 y0 s1 ðy0 b0 X0 Þ; a21 4a2 ¼ 0 ðs1 ¼ s2 Þ: (11.42)
From (11.34), the characteristic roots are given by pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a1 a21 4a2 s1 ; s2 ¼ 2a2 qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi RC ðRCÞ2 4LC : (11.46) ¼ 2LC The voltage source is equivalent to a short circuit for t 0; i.e., no energy is provided to the circuit until t > 0. It follows that ið0þ Þ ¼ 0:
Example 11.11. Figure 11.12 shows a series RLC circuit, where vS ðtÞ ¼ V0 uðtÞ.
The relation ið0þ Þ ¼ 0 is one initial value:
(c) Obtain an expression for the current iðtÞ. (b) Let R ¼ 600 O, L ¼ 100 mH, C ¼ 2mF, and V0 ¼ 1V. Draw a graph of the current versus time.
ið0þ Þ ¼ i0 ¼ 0:
ðt
iðt0 Þ dt0 ¼ V0 :
R ið0þ Þ þ L i0 ð0þ Þ 1 þ C
(11.43)
1
(11.44)
1
V0 : L
iðtÞ ¼ ðI1 es1 t þ I2 es2 t ÞuðtÞ;
d2 i di L C 2 þ RC þ i ¼ 0; dt dt
(11.45)
s2 ði0 b0 X0 Þ i00 i0 ¼ 0 s2 s1 s 2 s1 1 V0 V0 C ¼ ¼ qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi ; s2 s1 L ðRCÞ2 4LC
I1 ¼
L b C
s1 ði0 b0 X0 Þ i00 i0 ¼ 0 s2 s1 s2 s1 1 V0 V0 C ¼ qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi : (11.51) ¼ s2 s1 L ðRCÞ2 4LC
I2 ¼
R
+ –
(11.50)
where, from (11.42)
which is in standard form, with a2 ¼ LC; a1 ¼ RC; b0 ¼ 0. From (11.30) the forced response equals zero.
i a
(11.49)
From (11.38) with b0 ¼ 0, the complete response is given by
or
Fig. 11.12 See Example 11.11
iðt0 Þ dt0 ¼ V0 :
i0 ð0þ Þ ¼ i00 ¼
2
vS
0ðþ
The first term vanishes because ið0þ Þ ¼ 0. The integral vanishes because iðtÞ ¼ 0 for t < 0. Thus we have the second initial value
Differentiating (11.43) once with respect to time gives di d i 1 R þL 2þ i¼0 dt dt C
(11.48)
We obtain the other from (11.48) and (11.43). For t ¼ 0þ , (11.43) becomes
Solution: (a) By Kirchhoff’s voltage law, we have for t > 0 that di 1 Ri þ L þ dt C
(11.47)
364
11 Transient Analysis
where t is the time constant for the transient response. If the characteristic roots are real and distinct, it is convenient to define
1.5
1.0 i (mA)
t1 ¼
0.5
1 1 ; t2 ¼ ; s1 s2
(11.54)
and write the unforced response as 0
0
1
2
3
4
5
t (ms)
yu ðtÞ ¼ ðY1 et=t1 þ Y2 et=t2 ÞuðtÞ; a21 4a2 > 0;
Fig. 11.13 See Example 11.11
(b) We are given R ¼ 600 O; L ¼ 100 mH; C ¼ 2 mF; V0 ¼ 1V. For these values, the characteristic roots are
where t1 ; t2 are the time constants for the transient response. if the characteristic roots are complex conjugates (if a21 4a2 < 0), the expression yu ðtÞ ¼ ðY1 es1 t þ Y2 es2 t ÞuðtÞ;
3 1
3 1
s1 ¼ 1 10 s ; s2 ¼ 5 10 s : The initial values are i0 ¼ 0; i00 ¼
a21 4a2 6¼ 0
(11.56)
is correct but inconvenient because the exponential functions are complex. We can obtain a more convenient (and more easily interpreted) expression by writing the characteristic roots as
V0 ¼ 10 As1 : L
pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a1 j 4a2 a21 1 ¼ jo0 ; s; s ¼ t 2a2
From (11.51)
I1 ¼ 2:5 mA; I2 ¼ 2:5 mA:
(11.57)
where the time constant t and the ring frequency f0 are given by
The response is given by iðtÞ ¼ 2:5ðes1 t es2 t ÞuðtÞ mA:
(11.55)
(11.52)
1 2a2 o0 ; ; f0 ¼ ¼ a1 2p ReðsÞ qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 o0 ¼ ImðsÞ ¼ 4a2 a21 : 2a2 t¼
Figure 11.13 shows a graph of the response. We can express the unforced responses given by (11.37) in more convenient forms. If the characteristic roots are equal, it is convenient to express the unforced response as yu ðtÞ ¼ ðY1 þ Y2 tÞet=t uðtÞ; 1 t ¼ ; a21 4a2 ¼ 0; s1
(11.58)
From (11.42), the coefficients in (11.56) are given by s ðy0 b0 X0 Þ y00 ; s s sðy0 b0 X0 Þ y00 Y2 ¼ ¼ Y1 : s s Y1 ¼
ð11:53Þ
(11.59)
11.5 Second-Order Circuits
365
The coefficients Y1 ; Y2 are a conjugate pair, so we can simplify notation further by defining Y1 ¼ Y; Y2 ¼ Y
(11.60)
11.5.1 Summary: Second-Order Circuits The standard form of the differential equation governing a current or voltage in a second-order linear circuit subjected to a step excitation is
and expressing Y in polar form as Y ¼ jY jexp ðjyY Þ; yY ¼ ∡Y
a2
(11.61)
With the definitions above, (11.56) can be written yu ðtÞ ¼ ½Y expðstÞ þ Y expðs tÞuðtÞ ¼ ½Y expðstÞ þ ðY expðstÞ uðtÞ ¼ 2Re½Y expðstÞuðtÞ
d2 y dy þ a1 þ y ¼ b0 X0 : 2 dt dt
The complete response is given by y ¼ b0 X0 þ yu ; t > 0;
(11.62) and finally, as
X0 ¼ theðconstantÞ excitation for t > 0; b0 X0 ¼ forced response ¼ steadystate response; jb0 j ¼ the dc gain of the circuit; yu ¼ unforced response ¼ transient response: (11.69)
yu ðtÞ ¼ 2jY jexpðt=tÞ cosðo0 t þ yY ÞuðtÞ; (11.63)
where Y¼
s ðy0 b0 X0 Þ y00 ; s s
pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a1 þ j 4a2 a21 ; s¼ 2a2
To obtain an expression for the response, proceed as follows: Determine the state of the circuit at t ¼ 0 . Then use Kirchhoff’s laws and continuity of state to determine the initial values
(11.64)
(11.65)
y0 ¼ yð0þ Þ;
y00 ¼ y0 ð0þ Þ:
a21 4a2 : t¼
(11.66)
As always, you should express the quantities above in terms of symbols for circuit parameters before using any numerical values. Otherwise, if you use numerical values from the outset, you will be unable (without many repeated calculations) to determine how any particular circuit parameter affects the response, which is a principal reason for doing such analyses.
(11.70)
The form of the transient response depends upon the nature of the characteristic roots. Calculate
and 1 2a2 ; ¼ a1 ReðsÞ qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 o0 ¼ ImðsÞ ¼ 4a2 a21 : 2a2
(11.68)
where
¼ 2Re½jY j exp ðjyÞ exp½ðt=t þ j o0 ÞtuðtÞ ¼ 2jY jexp ðt=t Þ Re½exp ðj o0 t þ jyY uðtÞ;
a21 4a2 < 0;
(11.67)
(11.71)
If a21 4a2 > 0, the circuit is overdamped, the characteristic roots are real and distinct, and the complete response is given by
yðtÞ ¼ b0 X0 þ Y1 et=t1 þ Y2 et=t2 uðtÞ;
(11.72)
with pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a21 4a2 ; s1 ¼ 2a2 pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a1 a21 4a2 s2 ¼ ; 2a2 a1 þ
(11.73)
366
11 Transient Analysis
t1 ¼
1 ; s1
t2 ¼
1 ; s2
iS
and s2 ðy0 b0 X0 Þ y00 ; s 2 s1 s1 ðy0 b0 X0 Þ y00 : Y2 ¼ s2 s1
vL
(11.74) R
iL
C
Fig. 11.14 See Example 11.12
Y1 ¼
(11.75)
If a21 4a2 ¼ 0, the circuit is critically damped, the characteristic roots are real and equal, and the complete response is given by
yðtÞ ¼ b0 X0 þ ðY1 þ Y2 tÞet=t uðtÞ;
(11.76)
with t¼
2a2 ; a1
(11.77)
Example 11.12. In Fig. 11.14, C ¼ 50 pF, L ¼ 1 mH, and iS ðtÞ ¼ I0 ½1 uðtÞ, with I0 ¼ 5 mA. The response of interest is the voltage vL ðtÞ. Give values of R and plot the corresponding responses versus time for which the response is (a) underdamped, (b) critically damped, and (c) overdamped. Solution: For t<0, the circuit is in dc steady state. Thus vL ð0þ Þ ¼ vL ð0 Þ ¼ 0; iL ð0þ Þ ¼ iL ð0 Þ ¼ I0 :
and Y1 ¼ y0 b0 X0 ; a1 Y2 ¼ y00 þ ðy0 b0 X0 Þ: 2a2
Applying Kirchhoff0 s current law gives (11.78)
If a21 4a2 < 0, the circuit is underdamped, the characteristic roots are complex conjugates, and the complete response is given by
yðtÞ ¼ b0 X0 þ 2jY jet=t cosðo0 t þ yY Þ uðtÞ; (11.79) where yY ¼ ∡Y and s¼ Y¼
a1 þ
pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a21 4a2 ; 2a2
s ðy0 b0 X0 Þ y00 ; s s
(11.80)
(11.81)
and 1 2a2 t¼ ; o0 ¼ ImðsÞ ¼ a1 ReðsÞ qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 4a2 a21 : ¼ 2a2
ð vL dvL 1 t þC þ vL ðt0 Þdt0 R dt L 1 ¼ 0; t > 0; which yields
vL ð0þ Þ þ Cv0L ð0þ Þ þ iL ð0þ Þ ¼ 0 R
1 vL ð0þ Þ iL ð0þ Þ ) v0L ð0þ Þ ¼ C R I0 ¼ ffi 108 V s1 : C Differentiating (11.83) once with respect to time and rearranging terms yields the standardform differential equation LC
(11.82)
(11.83)
d 2 vL L dvL þ þ vL ¼ 0: dt2 R dt
The characteristic roots are given by
L
11.5 Second-Order Circuits
367
0 1 sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2 1 @ L L s1 ; s2 ¼ 4LC A: 2LC R R The characteristic roots are real and equal (the response is critically damped) if R ¼ R0 , given by
L R0
2
1 4LC ¼ 0 ) R0 ¼ 2
rffiffiffiffi L ffi 2:24kO: C
The response is underdamped if R > R0 and overdamped if R < R0 . We choose (arbitrarily) (a) R ¼ 5R0 , (b) R ¼ R0 , and (c) R ¼ R0 =5.
s1 ffi 4:52 105 s1 ; 1 t1 ¼ ffi 2:21 ms; s1 s2 ffi 4:43 107 s1 ; 1 t2 ¼ ffi 22:59 ns; s2 v0 ð0þ Þ ffi 2:28 V; V1 ¼ L s 2 s1 V2 ¼ V1 ffi 2:28 V; t t exp uðtÞ: vL ðtÞ ¼ V1 exp t2 t1 Figure 11.15(c) shows a graph of the response.
(a) R ¼ 5R0 (underdamped): s ffi ð8:94 þ j43:82Þ 105 s1 ; 1 t¼ ffi 1:12ms; ReðsÞ o ¼ ImðsÞ ffi 43:82 106 s1 ; V¼
s ðv0 b0 X0 Þ v00 v00 ¼ s s s s
p ffi j11:41 V; 2jV j ¼ 22:82 V; yV ¼ ; 2 t vL ðtÞ ¼ 2jV1 j exp cosðo t þ yV ÞuðtÞ: t Figure 11.15(a) shows a graph of the response. (b) R ¼ R0 (critically damped): s ffi 4:47 106 s1 ; 1 t ¼ ffi 223:61 ns; s V1 ¼ vL ð0þ Þ ¼ 0; V2 ¼ v0L ð0þ Þ ¼ 108 V s1 ; t vL ðtÞ ¼ V2 t exp uðtÞ: t Figure 11.15(b) shows a graph of the response. (c) R ¼ R0 =5 (overdamped):
Exercise 11.5. In Fig. 11.16, L ¼ 25 mH, C ¼ 1pF, and vS ðtÞ ¼ V0 uðtÞ with V0 ¼ 5 V. (a) Find the value R0 of the resistance R for which the response vC ðtÞ is critically damped. If R < R0 , is the response underdamped or overdamped? (b) Obtain expressions for the response vC ðtÞ for R ¼ 10 R0 , R ¼ R0 , and R ¼ 0:1R0 : A critically damped response is the boundary between overdamped and underdamped responses. Like any other mathematically specified response, an exactly critically damped response cannot be achieved. However, a physical circuit can be almost critically damped, meaning that the characteristic roots are almost equal. In such a case, (11.76) can be superior to either the overdamped or underdamped expressions for either computation or design. For example, if the characteristic roots of a circuit model are real and very nearly equal, using either the overdamped or underdamped models can require computing differences of nearly equal numbers, which can be troublesome for a computer (or pocket calculator). Moreover, if a circuit model believed to be accurate enough for design turns out to be critically damped, there is no reason to complicate the model just to obtain a more realistic slightly underdamped or overdamped response, when the critically damped response is close enough.
368
11 Transient Analysis 10 5 0
VL (V) –5 –10 –15 –20
0
1
2
3 t (μs)
4
5
6
0.8
1
1.2
8
10
12
(a) 0 –1 –2 –3 –4 VL (V)
–5 –6 –7 –8 –9 –10
0
0.2
0.4
0.6 t (μs)
(b) 0
–0.5 –1 VL (V) –1.5 –2 –2.5
0
2
4
6 t (μs) (c)
Fig. 11.15 See Example 11.12
The characteristic roots for a passive circuit consisting entirely of resistors and capacitors (no sources) must all be real, which means that such a circuit cannot be underdamped. To see why, first realize that damping increases with losses, or, conversely, the unforced response of an underdamped circuit becomes more oscillatory and lasts longer as losses diminish, because less energy is lost during each energy exchange. Losses approach zero if resistances in parallel with energystorage elements approach infinity and resistors in series with energy-storage elements approach zero. Now imagine a passive circuit containing only resistors and capacitors. Replace every resistor that is in parallel with a capacitor with an open circuit (infinite resistance) and every resistor that is in series with a capacitor with a short circuit. If that is done, what remains is a lossless circuit that is equivalent to a single capacitor. Such a circuit is first order and cannot possibly be underdamped. Similarly, the characteristic roots for a passive circuit consisting entirely of resistors and inductors (no sources) must all be real, which means that such a circuit cannot be underdamped. If you obtain an underdamped response (or complex characteristic roots) for a passive circuit consisting of only resistors and capacitors or only of resistors and inductors, you have made an error.6 Often, it is unnecessary to determine a complete response, being sufficient to determine only the initial and final states and the characteristic roots. For the overdamped case, the characteristic roots are real and distinct, and the smallest characteristic root (the largest time constant) largely determines the duration of the transient response. For the critically damped case, the characteristic roots are equal, and either root determines the duration of the transient. For the underdamped case, the characteristic roots are a conjugate pair. The real part determines the duration of the transient and the imaginary part determines the frequency (or period) of the oscillations. If the characteristic roots of an underdamped circuit are expressed as s jo, then the number of oscillations undergone before the transient dies out is approximately three to five times the ratio of the time constant t ¼ 1=s to the period T ¼ 2p=o; i.e., Number of oscillations ffi
+ –
vS
+
R L
C
vC –
Fig. 11.16 See Exercise 11.5
5t 5o ¼ : T 2ps
6
A circuit containing only resistors, capacitors, and dependent sources (active devices) can be underdamped, as can a circuit containing only resistors, inductors, and dependent sources.
11.5 Second-Order Circuits
369
11.5.2 Dominant Time Constant (or Characteristic Root) From Section 11.5.1, the unforced response of an overdamped second-order circuit to a step excitation X0 uðtÞ is given by yðtÞ ¼ Y1 et=t1 þ Y2 et=t2 uðtÞ;
(11.84)
where s2 ðy0 b0 X0 Þ y00 ; s2 s 1 s1 ðy0 b0 X0 Þ y00 ; Y2 ¼ s2 s1 Y1 ¼
pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a21 4a2 s1 ¼ ; 2a2 pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a1 a21 4a2 ; s2 ¼ 2a2
(11.85) Example 11.13. The response vL of a certain circuit to an excitation vS is governed by the differential equation
a1 þ
(11.86) a2
and t1 ¼
1 ; s1
t2 ¼
1 ; s2
We wish to show that the duration of the transient is determined mainly by the larger of the two time constants. From (11.85) and (11.84), the transient is given for t>0 by s2 ðy0 b0 X0 Þ y00 t=t1 e s2 s1 s1 ðy0 b0 X0 Þ y00 t=t2 e s2 s1 " y0 b0 X0 t=t1 ¼ s1 et=t2 s2 e s2 s1 # y00 et=t1 et=t2 y0 b0 X0 " y0 b0 X0 1 1 ¼ et=t1 þ et=t2 s2 s1 t2 t1 # y0 et=t1 et=t2 0 : (11.87) y0 b0 X0
yu ðtÞ ¼
The initial amplitude of the second pair of exponentials in the brackets is zero because e0 e0 ¼ 0. We may assume without loss of generality that t2 >t1 , in which case both the initial magnitude and the durat=t2 tion of the term t1 exceed those of the term 1 e 1 t=t1 t2 e . It follows that the duration of the transient component of the step response of an overdamped second-order circuit is approximately five times the larger time constant. If one time constant is much larger than the other, we call the larger one the dominant time constant. The step response of an overdamped second-order circuit having a dominant time constant approximates that of a first-order circuit for all but a brief time at the beginning of the response.
d 2 vL dvL þ a1 þ v L ¼ vS ; 2 dt dt
where a2 ¼ 7 ms2 and a1 ¼ 11 ms. It is known that for a step excitation vS ¼ V0 uðtÞ with V0 ¼ 1 V, the initial conditions are vL ð0þ Þ ¼ 0; v0L ð0þ Þ ¼ 10 V s1 : We wish to show that the response is characterized by a dominant time constant. From (11.86), the characteristic roots are pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a21 4a2 s1 ¼ ffi 96:88 s1 ; 2a2 pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a1 a21 4a2 s2 ¼ ffi 1:475 103 s1 ; 2a2 a1 þ
and the time constants are t1 ¼
1 ffi 10:3 ms; s1
t2 ¼
1 ffi 678 ms: s2
Because t1 >10t2 , we expect the exponential having time constant t1 to be dominant. From (11.85), with b0 ¼ 1,
370
11 Transient Analysis
where
1 0.9
s ðy0 b0 X0 Þ y00 ; s s pffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi a1 þ a21 4a2 ; s¼ 2a2 Y¼
0.8 0.7 0.6 0.5
(11.89)
0.4
and
0.3 0.2 0 –0.1 –0.2
1 2a2 ; o0 ¼ ImðsÞ ¼ a1 ReðsÞ qffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 1 4a2 a21 : ¼ 2a2
t¼
0.1
0
2
4
6
8
10 t (ms)
vL
vˆL
V0
V0
12
14
16
18
20
The steady-state (forced) component yf and transient (unforced) component yu of the response are given by
Fig. 11.17 See Example 11.13
yf ðtÞ ¼ b0 X0 uðtÞ; yu ðtÞ ¼ 2jY jet=t cosðo0 t þ yY ÞuðtÞ:
s2 ðy0 V0 Þ y00 Y1 ¼ ¼ 1:063 V; s2 s1 s1 ðy0 V0 Þ y00 ¼ 63 mV: Y2 ¼ s2 s1
vL ðtÞ ¼ b0 V0 þ Y1 e
t=t1
þ Y2 e
t=t2
uðtÞ:
Figure 11.17 shows (solid line) a graph of the step response and (dotted line) a graph of only the steady-state component and first exponential, given by v^L ðtÞ ¼ b0 V0 þ Y1 et=t1 uðtÞ:
The graphs are indistinguishable for times greater than about 2 ms.
11.5.3 Damping Factor The response of an underdamped second-order circuit has the form
yðtÞ ¼ b0 X0 þ 2jY jet=t cosðo0 t þ yY Þ uðtÞ; (11.88)
(11.91)
The duration of the transient component is determined by the time constant t. Also of interest are the maximum amplitude and the number of oscillations the transient undergoes (if any) before vanishing (before becoming insignificant). A useful measure in that regard is the dimensionless damping factor
Thus the response is given by
(11.90)
d¼
1 1 T ¼ ¼ ; o0 t 2pf0 t 2pt
(11.92)
which, except for the factor ð2pÞ1 , is the ratio of the period T ¼ 2p=o0 of the sinusoidal factor cosðo0 t þ yY Þ to the time constant t of the exponential factor et=t . From (11.92), the number of cycles executed by the sinusoidal factor in (11.91) before the transient vanishes (during 0 t < 5t) is given approximately by 5t 5 0:8 ¼ ffi : T 2pd d
(11.93)
If d is large, the period of the sinusoidal factor is larger than the time constant of the exponential factor, there are few or no oscillations before the transient vanishes, and the circuit is relatively heavily damped. If d is small, the period of the sinusoidal factor is smaller than the time constant of the exponential factor, there are a few or perhaps many oscillations before the transient vanishes, and the circuit is relatively lightly damped.
11.5 Second-Order Circuits
371 0.6 0.4
d = 0.8
0.2 yu
yu
X0
X0 0
– 0.2
d = 0.5
0.2 0
0
2
4
– 0.2
6
0
2
t/τ
4
6
t/τ 1
1 d = 0.2
d = 0.1
0.5
0.5 yu
yu
X0
X0
0
– 0.5
0 – 0.5
0
2
4
6
t/τ
–1
0
2
4
6
t/τ
Fig. 11.18 Unforced (transient) response of a second-order circuit for various damping factors
Figure 11.18 shows graphs of an unforced response for four values of the damping factor d. As the damping factor decreases, the number of oscillations and the maximum amplitude of the transient both increase.
11.5.4 Extrema of the Unforced Component of an Underdamped Response The unforced component yu of an underdamped response is given by:
Exercise 11.6. Use (11.93) to estimate the number of cycles executed before the transient vanishes for d ¼ 0:8; 0:5; 0:2; 0:1. Are your answers in approximate agreement with Fig. 11.18?
Exercise 11.7. Show that the damping factor d for an underdamped response is the magnitude of the ratio of the real part to the imaginary part of either characteristic root.
Exercise 11.8. What is the damping factor for a critically damped circuit?
yu ðtÞ ¼ 2jY jet=t cosðo0 t þ yY Þ; t > 0:
(11.94)
The extrema of the unforced response are of interest. Differentiating the right side of (11.94) once with respect to time and setting the result to zero gives
1 cosðo0 t þ yY Þ þ o0 sin ðo0 t þ yY Þ ¼ 0 t where we have used the fact that t 2jY j exp 6¼ 0 t It follows that cosðo0 t þ yY Þ þ o0 sinðo0 t þ yY Þ ¼ 0 1 ) sin o0 t þ yY þ tan1 ¼0 o0 t
) sin o0 t þ yY þ tan1 ðdÞ ¼ 0 ) o0 t þ yY þ tan1 ðdÞ ¼ kp; k ¼ 0; 1; 2;
372
11 Transient Analysis
The solutions are the times tk given by kp yY tan ðdÞ ; o0 k ¼ k0 ; k0 þ 1; k0 þ 2; ;
tk ¼
vS
1
+
L
+ –
R
C
vC –
(11.95) Fig. 11.19 See Example 11.14
where k0 is the smallest nonnegative integer for which tk0 0þ . The corresponding extrema are given by yu ðtk Þ ¼ 2jY jetk =t cosðo0 tk þ yY Þ; k ¼ k0 ; k0 þ 1; k0 þ 2; :
(11.96)
If the steady-state response is non-negative, extrema given by (11.96) are called undershoots if they are below the steady-state response and are called overshoots if they are above the steady-state response. The terminology is reversed if the steady-state response is negative. Equation (11.95) is derived by solving for times at which the time derivative of the associated current or voltage equals zero. If the maximum magnitude of a current or voltage occurs at a jump discontinuity, (11.95) can give an incorrect result. For example, if yY ¼ 0 in (11.94), the maximum magnitude of yu ðtÞ occurs at t ¼ 0þ , and not at any of the values given by (11.95). Thus, always evaluate (11.94) for t ¼ 0þ to see if jyu ð0þ Þj is larger than the largest of the values given by (11.95). If not, the maximum magnitude of the transient is given by (11.96) for k ¼ k0 : Exercise 11.9. Show that yu ðtk Þ ¼ 2jY jetk =t cosðo0 tk þ yY Þ; k ¼ k0 ; k0 þ 1; k0 þ 2;
can be expressed t 2ð1Þk jY j k yu ðtk Þ ¼ pffiffiffiffiffiffiffiffiffiffiffiffiffi exp ; 2 t 1þd k ¼ k0 ; k0 þ 1; k0 þ 2;
Example 11.14. In Fig. 11.19, R ¼ 1 kO, C ¼ 100 nF, L ¼ 25 mH, and vS ¼ V0 uðtÞ, with V0 ¼ 5 V.
(a) Obtain an expression for the response vC ðtÞ, assuming the response is underdamped. (b) Find the times at which the first two extrema of the unforced response occur and the amplitudes of those extrema. (c) Plot the response versus time for the circuit parameters given in part (b). Solution: (a) Kirchhoff0 s current law gives
C
dvC 1 1 þ vC þ dt R L
ðt 1
½vC ðt0 Þ vS ðt0 Þdt0 ¼ 0: (11.97)
Differentiating once with respect to time and rearranging terms gives, for t > 0 LC
d2 vC L dvC þ þ vC ¼ vS ¼ V0 ; t > 0: dt2 R dt
The dc gain is unity. The steady-state response is vC ss ¼ V0 ¼ 5 V: The characteristic roots are
1 1 s; s ¼ 2RC 2LC
s ffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi L 2 4LC R
ffi ð5:00 þ j19:36Þ 103 s1 : The source appears as a short circuit for t < 0, so no energy is stored in the inductor or capacitor at t ¼ 0þ . Thus, vC ð0þ Þ ¼ 0 and iL ð0þ Þ ¼ 0. From (11.97) we find, for t ¼ 0þ
11.6 Time Invariance, Superposition, and Pulse Response
373 8
dvC 1 C þ vC ð0þ Þ dt t¼0þ R ð 0þ 1 ½vC ðt0 Þ vS ðt0 Þdt0 þ L 1 dvC ¼C þ0 þ 0 ¼ 0 dt t¼0þ dvC ) ¼ v0C ð0þ Þ ¼ 0: dt t¼0þ
7 6 5
vC (V) 4 3 2 1 0
From (11.81)
0
200
400
600
800
1000
t (μs)
s ½vC ð0þ Þ V0 v0C ð0þ Þ ðs sÞ s V0 ; ¼ ðs s Þ
V¼
Fig. 11.20 See Example 11.14
which are
which gives 2jV1 j ffi 5:16 V; yV ffi 2:89:
(11.98)
The complete response is given by
at which times
t
vC ðtÞ ¼ V0 þ 2jV j exp t
cosðo0 t þ yV Þ uðtÞ:
t2 ¼ 162:2 ms; t3 ¼ 324:5 ms;
vC ðt2 Þ ¼ 7:22 V; vC ðt3 Þ ¼ 4:013 V: (11.99)
where
As a check, we compute the initial value of the unforced response, given by 2jV j cosðyV Þ ¼ 5 V:
1 ffi 200 ms; t¼ ReðsÞ
(11.100)
o0 ¼ ImðsÞ ffi 19:36 103 s1 : (b) The damping factor is d¼
1 ffi 0:258; o0 t
From (11.95), the extrema of the unforced response occur at the times tk given by kp RV tan1 ðdÞ ; o0 k ¼ k0 ; k0 þ 1; k0 þ 2; ;
Thus, vC ðt2 Þ ¼ 7:22 V is the maximum magnitude of the unforced response. The steady-state response is vC ð1Þ ¼ V0 ¼ 5 V, so the first (largest) overshoot is 2.22 V and the first (largest) undershoot is 987 mV. (c) Figure 11.20 shows a graph of the step response.
11.6 Time Invariance, Superposition, and Pulse Response
tk ¼
A circuit for which the response yðtÞ to an excitation xðtÞ is governed by a differential equation of the form
374
an
11 Transient Analysis
(11.101), being linear, also obeys the following principle of amplitude scaling: Let yðtÞ denote the response to an excitation xðtÞ. Then the response to KxðtÞ, where K is a constant, is given by KyðtÞ. The proof is trivial, as it amounts to multiplying (11.101) by K.
dn y d n1 y dy þ an1 n1 þ þ a1 þ y n dt dt dt dn x d n1 x dx ¼ bn n þ bn1 n1 þ þ b1 þ b0 x dt dt dt (11.101)
obeys the following principle of time invariance: If yðtÞ is the response to an excitation xðtÞ, then the response to xðt t0 Þ, where t0 is a fixed delay, is yðt t0 Þ. What this means is that the mathematical form of the response does not depend upon the time at which the excitation is applied. In other words, delaying the excitation simply delays the response by the same amount, but does not change its form. Figure 11.21 illustrates time-invariance. In Fig. 11.21a a step excitation vS ¼ V0 uðtÞ is applied as shown to a series RC circuit. The voltage across the capacitor (the response) is given by v C ¼ V0 1 et=t uðtÞ, where t ¼ RC. In Fig. 11.21b, a step excitation vS ¼ V0 uðt t0 Þ is applied to an identical circuit and the response is
given by vC ¼ V0 1 eðtt0 Þ=t uðt t0 Þ. Were it not for time-invariance, life would be a mess. A CD you played on your audio system would sound different each time you played it. Circuits laboratories would be frustrating, because identical experiments performed at different times on identical circuits would yield different results. A two-port circuit whose response yðtÞ to an excitation xðtÞ is governed by an equation of the form
Example 11.15. Let yðtÞ denote the response of a certain circuit to an excitation xðtÞ ¼ X0 uðtÞ. Then the response to x1 ðtÞ ¼ 3 X0 uðtÞ is y1 ðtÞ ¼ 3yðtÞ:
Example 11.16. Let yðtÞ denote the response of a certain circuit to excitation xðtÞ. The response of the circuit to excitation x1 ðtÞ ¼ 5xðtÞ 2xðt t0 Þ þ 10xðt t1 Þ is given by y1 ðtÞ ¼ 5yðtÞ 2yðt t0 Þ þ 10yðt t1 Þ: We may use amplitude scaling, time invariance, and superposition to obtain the response of a linear circuit to any piecewise constant excitation from the response of the circuit to a step excitation. A particular piecewise-constant excitation of interest in many applications is a rectangular pulse, illustrated by Fig. 11.22 and described by vS ¼ V0 uðtÞ V0 uðt t0 Þ:
vS
(11.102)
vC
V0
+
vS
+ R C
–
V0
vC – t
t
0
0 (a)
vS
vC
V0
+
vS
C
– 0
Fig. 11.21 Illustrating timeinvariance
t0
+
R
V0
vC –
t
t0 0 (b)
t
11.7 Operator Notation
375 2 1.67
vS V0
0
0 0
t0
t
−2
0
Fig. 11.22 Rectangular pulse expressed by (11.102) i2 (t) (mA)
To obtain the response of a linear time-invariant circuit to such an excitation, we need only obtain the response to the step V0 uðtÞ and subsequently apply time-invariance and superposition. Thus if the response to V0 uðtÞ is given by vL ðtÞ, then by timeinvariance, the response to V0 uðt t0 Þ is given by vL ðt t0 Þ and by superposition, the response to vS ¼ V0 uðtÞ V0 uðt t0 Þ is given by vL ¼ vL ðtÞ vL ðt t0 Þ: Example 11.17. Refer to Example 11.11. Find the current i2 ðtÞ if the applied voltage is given by v2 ðtÞ ¼ V0 uðtÞ V0 uðt t0 Þ. Solution: From Example 11.11, the response to vS ðtÞ ¼ V0 uðtÞ is given by iðtÞ ¼ I ðes1 t es2 t ÞuðtÞ. By time invariance and superposition, the response to v2 ðtÞ ¼ V0 uðtÞ V0 uðt t0 Þ ¼ vS ðtÞ vS ðt t0 Þ is given by i2 ðtÞ ¼ iðtÞ iðt t0 Þ ¼ Iðes1 t es2 t ÞuðtÞ I es1 ðtt0 Þ es2 ðtt0 Þ uðt t0 Þ: Figure 11.23 shows a graph of the response (compare with Fig. 11.13).
Exercise 11.10. Refer to Fig. 11.24, where R ¼ 100 kO and C ¼ 100 pF. Let V0 ¼ 5V and t0 ¼ 50 ms. Sketch neatly and label fully a graph of the voltage vR across the resistor if (a) vS ðtÞ ¼ V0 uðtÞ; with V0 ¼ 5 V;
10
5 t (ms)
V0 R
(mA)
Fig. 11.23 See Example 11.17
+ vS –
+
C
Fig. 11.24 See Exercise 11.10
R
vR –
(b) vS ðtÞ ¼ V0 uðtÞ V0 uðt t0 Þ, with V0 ¼ 5 V and t0 ¼ 50 ms; and (c) vS ðtÞ ¼ 2V0 uðtÞ 3V0 uðt t0 Þ þV0 uðt 2t0 Þ, with V0 ¼ 5 V and t0 ¼ 50 ms:
11.7 Operator Notation In operator notation, differentiation with respect to time is indicated by multiplication by the operator s: Thus dy d2 y d3 y 2 $ s y; $ s3 y; ; $ s y; dt dt2 dt3
(11.103)
where y can be any function of time. The SI unit of the operator s is s1 , so confusion is possible, especially where both the operator s and the unit s occur in an expression. To avoid confusion, underline the unit s in written work involving the operator s. We may also use operator notation as shorthand for integration. Thus ðt 1 vðt0 Þdt0 $ vðtÞ: (11.104) s 1
376
11 Transient Analysis
Equation (11.104) makes sense: if s denotes differentiation, then 1=s should denote integration, because ðsÞð1=sÞ ¼ 1 (which denotes those operations in succession). When using operator notation in this way, be sure the limits of integration extend from 1 to t; for example. ð 1 t 1 vL ðt0 Þdt0 $ vL : L 1 sL Operator notation allows us to manipulate coupled differential equations algebraically, eliminate unwanted variables, and obtain a single differential equation relating excitation and response. There is no magic here. In this context, operator notation is simply a shorthand that makes it easier to see what operations must be performed to obtain a desired (single) differential equation. Example 11.18. In Fig. 11.25, vS ¼ V0 uðtÞ. (a) Obtain a differential equation governing the voltage vC for t > 0. (b) Obtain expressions for the initial values vC ð0þ Þ and v0C ð0þ Þ. Solution: (a) We use Kirchhoff’s current law to obtain two node equations for t > 0 : v C V0 dvC vC vL þ þC ¼ 0; R1 dt R2 vL vC 1 þ R2 L
ðt 1
vL ðt0 Þdt0 ¼ 0:
¼
R2 V0 ; t1 ¼ ðR1 kR2 ÞC: (11.108) R 1 þ R2
Equation (11.106) is written using operator notation as L 1 L vL ¼ 0; vC þ þ R2 s R2 which yields st2 vC þ ð1 þ st2 ÞvL ¼ 0 L t2 ¼ : R2
(11.109)
We are interested only in the voltage vC , so we eliminate vL . From (11.109) vL ¼
st2 vC : 1 þ st2
(11.110)
Using the right side of (11.110) for vL in (11.108) gives
(11.105)
ð1 þ st1 ÞvC ¼
(11.106)
Equation (11.105) is written using operator notation as 1 1 vL V 0 þ þ sC vC ¼ ; (11.107) R2 R1 R1 R2
R1 vL R1 þ R2
ð1 þ st1 ÞvC
R1 st2 vC R1 þ R2 1 þ st2
R2 V0 ; R1 þ R2
(11.111)
which yields vC ¼
t1 t2
s2
k2 ð1 þ st2 ÞV0 ; þ ðt1 þ t2 k1 t2 Þs þ 1
or
which yields t1 t2 s2 vC þ ðt1 þ t2 k1 t2 ÞsvC þ vC ¼ k2 ð1 þ st2 ÞV0 ; (11.112)
R1
vS
R2
vC
+ –
C ref
Fig. 11.25 See Example 11.18
corresponding to the standard-form differential equation
vL L
d2 vC dvC þ vC þ ðt1 þ t2 k1 t2 Þ 2 dt dt dV0 þ k2 V0 ¼ k2 V0 ; ¼ k2 t 2 dt
t1 t 2
11.8 Problems
377 v1
C
where t1 ¼ ðR1 kR2 ÞC; t2 ¼ k1 ¼
L ; R2
R1 R2 ; k2 ¼ ; R1 þ R2 R1 þ R2
v2
R
vS +–
2C
C R
x
+
vo
–
2R
and dV0 =dt ¼ 0 because V0 is constant. (b) No energy is supplied to the circuit before t ¼ 0. Thus there can be no energy stored in the circuit for t ¼ 0þ , which means vC ð0þ Þ ¼ vC ð0 Þ ¼ 0 and iL ð0þ Þ ¼ iL ð0 Þ ¼ 0. For t ¼ 0þ , (11.105) gives v C ð 0 þ Þ V0 þ Cv0C ð0þ Þ þ iL ð0þ Þ ¼ 0 R1 V0 ) Cv0C ð0þ Þ ¼ ; R1 because vC ð0þ Þ ¼ 0 and iL ð0þ Þ ¼ 0. The initial values are vC ð0þ Þ ¼ 0;
v0C ð0þ Þ ¼
V0 : R1 C
Exercise 11.11. The circuit in Fig. 11.26 is called a twin-T. Note that there is no connection at the apparent intersection labeled x. (a) Obtain a differential equation in standard form that relates the output vo to the excitation vS . (b) Let RC ¼ 10 ms. Find the characteristic roots and show that the circuit is overdamped. Why must this circuit be overdamped? (Why can it not be underdamped?) (c) Find the approximate duration of the transient response to an excitation of the form vS ¼ V0 uðtÞ.
11.8 Problems
Section 11.2 is prerequisite for the following problems.
Fig. 11.26 See Exercise 11.11
P 11.1 Use unit step functions to express each of the functions below. Sketch neatly and label fully a graph of each. 8 0; t 0; > > > ( > < V0 ; t 0; V0 ; 0 < t t1 ; ðaÞv ¼ ðbÞv ¼ > 2V0 ; t1 < t t2 ; 2V0 ; t > 0; > > > : 3V0 ; t > t2 ; 8 0; t 0; > > > > < I0 ; 0 < t t1 ; ðcÞi ¼ > I0 ; t1 < t 2t1 ; > > > : 0; t > 2t1 ; 8 8 0; t 0; > > > > < < 0; V0 t ðdÞv ¼ ; 0 < t t; ðeÞi ¼ I0 ; > > t > : > : 0; V0 ; t > t;
t t1 ; t1 < t t1 ; t > t1:
P 11.2 The unit step function can be defined in various ways. Three possible definitions are ua ðtÞ ¼ ub ðtÞ ¼
0; 1; 0;
1; 8 0; > > < uc ðtÞ ¼ 1=2; > > : 1;
t 0; t > 0; : t < 0; t 0; t < 0; t ¼ 0; t > 0:
Are there any significant differences among these three definitions insofar as they are used to describe (approximately) physical quantities such as current and voltage? If so, what are they?
378
11 Transient Analysis R2
Section 11.4 is prerequisite for the following problems.
C
P 11.3 Refer to Fig. P 11.1, where vS ðtÞ ¼ V0 uðtÞ. Obtain an expression for the current i for t > 0. P 11.4 Refer to Fig. P 11.2, where vS ¼ V0 uðtÞ. Obtain an expression for the voltage vðtÞ. P 11.5 In Fig. P 11.3, i0 ðtÞ ¼ 2I0 þ 3I0 uðtÞ. Obtain an expression for the voltage vL across the inductor two ways: (1) directly from the given circuit, using Kirchhoff’s current law, and (2) using a source transformation and Kirchhoff’s voltage law. Identify the transient and steady-state components. If I0 ¼ 1 mA, L ¼ 10mH, and R ¼ 100kO, what are the duration of the transient and the maximum voltage (magnitude) across the inductor? P 11.6 Refer to Fig. P 11.4, where the op amp is ideal and iS ðtÞ ¼ I0 uðtÞ. Obtain an expression for the voltage vo ðtÞ. P 11.7 In Fig. P 11.5, the op amp is ideal. Describe the response vL to a step excitation vS ¼ V0 uðtÞ as completely as possible, without writing a differential equation.
p
R1
iS
n
– +
RL
Fig. P 11.4 See Problem P 11.6
R2 C
R1
vS
vn
+ –
Fig. P 11.5 See Problem P 11.7
C R2
vL
–
vS
+ –
RL
+
vS +
R1
vL
–
R1 R0
vo
o
RL
+
–
R2
C
Fig. P 11.6 See Problem P 11.8
i
Fig. P 11.1 See Problem P 11.3
vS
+
C
+ –
R i
Fig. P 11.2 See Problem P 11.4
vS
+ –
v
R
R
iC
iL
C
–
L
Fig. P 11.7 See Problem P 11.9
+ i0
Fig. P 11.3 See Problem P 11.5
R
L
vL –
P 11.8 In Fig. P 11.6, the op amp is ideal. Describe the response vL to a step excitation vS ¼ V0 uðtÞ as completely as possible, without writing a differential equation.
11.8 Problems
379
P 11.9 In Fig. P 11.7, vS ¼ V0 uðtÞ. Without writing a differential equation, give expressions for the currents iC, iL. P 11.10 In Fig. P 11.8, iS ¼ I0 uðtÞ. Without writing a differential equation, give expressions for the voltages vC, vL. Section 11.5 is prerequisite for the following problems. P 11.11 In Fig. P 11.9, R ¼ 10 O, L ¼ 1 mH, C ¼ 100 nF, and iðtÞ ¼ I0 uðtÞ, with I0 ¼ 1 A. Obtain an expression for the voltage vðtÞ.
R
iS
+
(a) Obtain a standard-form differential equation governing the voltage vL . (b) Let R ¼ 10 kO; C ¼ 1nF; RF ¼ 500 O; RQ ¼ 2:5 kO; and RG ¼ 30 kO. Obtain an expression for the voltage vL ðtÞ.
R L
C
vC
+
–
vL
P 11.12 In Fig. P 11.10, the input is a given by vin ðtÞ ¼ V0 uðtÞ, with V0 ¼ 1 V. Sketch neatly and label fully a graph of the output vout ðtÞ versus time. P 11.13 Refer to Fig. P 11.11, where iS ðtÞ ¼ I0 uðtÞ, I0 ¼ 1 mA, R1 ¼ 10 kO, R2 ¼ 100 kO; m0 ¼ 100, C1 ¼ 10 nF, and C2 ¼ 1 nF. Obtain an expression for the voltage vC ðtÞ for t > 0. P 11.14 Refer to Fig. P 11.12. Show that the circuit is overdamped for R ¼ 7:5 kO and underdamped for R ¼ 22 kO. For each value of R, express the voltages vR and vC in terms of the amplitude of the step excitation for t > 0. P 11.15 In Fig. P 11.13, vS ¼ V0 uðtÞ, with V0 ¼ 1 V.
–
Fig. P 11.8 See Problem P 11.10 + iS
R1
+ i
R
Fig. P 11.9 See Problem P 11.11
–
–
vin
+
R L
vout
C
–
vC
C2
–
Fig. P 11.11 See Problem P 11.13
+ +
+
R2
v
C
L
+ – μv 0 1
v1
C1
vS
vR
– iL
R
+ –
–
L
+ C
V = 1V
vC L 0= 25 mH –
R = 10kΩ, C = 1pF, L = 65 mH
vS = V0 u(t) C = 100 pF
Fig. P 11.12 See Problem P 11.14
Fig. P 11.10 See Problem P 11.12
10R
R
vS
RG
v2
–
C
vH
+
– +
RQ
Fig. P 11.13 See Problem P 11.15
RF
10R
vB
C RF – +
vL
380
11 Transient Analysis C1
vin
iin
R
vin2 (t) 3V0
–
R
vout
+
v1
2V0 V0
C2
T
–V0
3T
2T
t
–2V0
Fig. P 11.14 See Problem P 11.16 Fig. P 11.17 See Problem P 11.19 C R
vin
R
vout
+ –
C
vin2 (t)
vin1 (t) V0
3V0 2V0 V0
R
2R
o
Fig. P 11.15 See Problem P 11.17
T
t
o –V0
(a) R
vin C
R
2R
5T
6T
t
(b)
Fig. P 11.18 See Problem P 11.21
vout
+ –
C
3T
R
(b) Obtain an expression for the voltage vout ðtÞ. (c) Let V0 = 1 V RC ¼ 1 ms. Construct a graph of the voltage vout versus time.
Fig. P 11.16 See Problem P 11.18
P 11.16 In Fig. P 11.14, vin ¼ V0 uðtÞ. (a) Obtain a standard-form differential equation governing the voltage vout . (b) Show that the response is underdamped if C1 >C2 . P 11.17 In Fig. P 11.15, vin ¼ V0 uðtÞ. (a) Obtain a standard-form differential equation governing the voltage vout . (b) Obtain an expression for the voltage vout ðtÞ. (c) Let V0 = 1 V RC ¼ 1 ms. Construct a graph of the voltage vout versus time. P 11.18 In Fig. P 11.16, vin ¼ V0 uðtÞ. (a) Obtain a standard-form differential equation governing the voltage vout .
Section 11.6 is prerequisite for the following problems. P 11.19 The response of a certain circuit to a step excitation vin 1 ðtÞ ¼ V0 uðtÞ is given by vout1 ðtÞ ¼ 5V0 et=t uðtÞ. Obtain an expression for the response to the excitation shown in Fig. P 11.17. The excitation is zero for times not shown. P 11.20 The response of a certain circuit to a sinusoidal excitation vin1 ðtÞ ¼ V0 cosðo0 tÞ is given by vout1 ðtÞ ¼ 100V0 cosðo0 t 0:5Þ. Find the response of the circuit to the excitation vin2 ðtÞ ¼ 2 V0 cosðo0 t þ 0:2Þ þ V0 sinðo0 tÞ: P 11.21 Let vout1 ðtÞ denote the response of a certain circuit to the excitation vin1 ðtÞ shown in Fig. P 11.18 (a).
11.8 Problems
381 vin (t)
vC
V0
R1
vL
i o
t
T
L
R2
C
Fig. P 11.19 See Problem P 11.22 Fig. P 11.22 See Problem P 11.26 vin V0
vin 0
T
R
+
C
+ –
R
vout
RS
–
t
R
+ –
R
– +
C1
vS
C2
– +
R
vL RL
Fig. P 11.20 See Problem P 11.23
iin
Fig. P 11.23 See Problem P 11.27
I0
+ iin 0
T
R
t
C
R1
vout
v3
R2
vL
–
vS
+ –
i1
R3
i2
L
Fig. P 11.21 See Problem P 11.24, 25
Give an expression for the response vout2 ðtÞ of the circuit to the excitation shown in Fig. P 11.18(b). P 11.22 The response of a certain circuit to a step excitation v0 ðtÞ ¼ V0 uðtÞ is given by v1 ðtÞ ¼ V0 1 et=t uðtÞ. Give an expression for the response of the circuit to the excitation shown in Fig. P 11.19, where vin ðtÞ ¼ V0 for all t < T. P 11.23 Refer to Fig. P 11.20. A rectangular pulse of voltage is applied to an RC circuit, as shown. Specify the time constant RC in terms of the duration T of the pulse such that vout ðT Þ ¼ 0:95vout ð0þ Þ. P 11.24 Refer to Fig. P 11.21. A rectangular pulse of current is applied to an RC circuit, as shown. Specify the time constant RC in terms of the duration T of the pulse such vout ðT Þ ¼ 0:95 RI0 . P 11.25 Refer to Fig. P 11.21. A rectangular pulse of current is applied to an RC circuit, as shown. Specify the time constant RC in terms of the duration T of the pulse such that no more than 5% of the total energy dissipated in the resistor is dissipated for t T. Hint: Obtain expressions for the energy e1 dissipated for t < T and the energy e2 dissipated for t > T. Then form the ratio e2 =ðe1 þ e2 Þ. Simplify the
Fig. P 11.24 See Problem P 11.28, 29
resulting expression by assuming T t, as seems reasonable in view of the specification, and solve e2 =ðe1 þ e2 Þ ¼ 0:05 for the time constant. Section 11.7 is prerequisite for the following problems. P 11.26 Refer to Fig. P 11.22, where iS ðtÞ ¼ I0 uðtÞ, I0 ¼ 1 mA, R1 ¼ 100 O, R ¼ 100 kO, L ¼ 100 mH, and C ¼ 100 nF. Obtain an expression for the voltage vC ðtÞ for t > 0. Use any reasonable approximations. P 11.27 Refer to Fig. P 11.23, where vS ¼ V0 uðtÞ. Obtain the standard-form differential equation that governs the response for t > 0. P 11.28 In Fig. P 11.24, vS ¼ V0 uðtÞ. Obtain standard-form differential equations governing the indicated mesh currents and show that the time constants for the two mesh currents are the same. P 11.29 In Fig. P 11.24, vS ¼ V0 uðtÞ. Obtain standard-form differential equations governing the indicated
382
11 Transient Analysis RS
va i1
C1
R1
vL i2
i3
RS = 50 Ω C1 = 500 nF
+ –
vS
RL
+ –
RL = 5 k Ω C2
C2 = 50 nF
vS
v1 R2
R3
vL
vC
L
Fig. P 11.26 See Problem P 11.31
C
Fig. P 11.25 See Problem P 11.30 R1
node voltages and show that the time constants for the two node voltages are the same. P 11.30 Refer to Fig. P 11.25, where vS ðtÞ ¼ V0 uðtÞ, with V0 ¼ 5 V. Obtain an expression for the voltage vL . P 11.31 Refer to Fig. P 11.26. Obtain a standardform differential equation relating the voltage vC to the voltage vS . Express the coefficients of the differential equation as functions of the circuit parameters. P 11.32 Refer to Fig. P 11.27. (a) Obtain a standardform differential equation relating the voltage vC to the source voltage vS . (b) Let vS ¼ V0 uðtÞ and show that the equation for t > 0 may be written as
vS
+ –
R2
vL L
vC C
Fig. P 11.27 See Problem P 11.32
o2
d2 vC dvC þ vC ¼ 0: þt 2 dt dt
Express the parameters o and t in terms of the circuit parameters. (c) Show that the response is underdamped if ot < 2.
Chapter 12
Sinusoids, Phasors, and Impedance
This chapter describes how real sinusoids are represented using complex quantities called phasors; how circuits containing resistors, capacitors, and inductors are represented using complex quantities called impedances and admittances; and how phasors, impedances, and admittances are used for analyzing sinusoidally excited circuits. This is a long chapter because it extends methods treated in several previous chapters to sinusoidally excited circuits. Ability to obtain the output of a circuit for a sinusoidal input is important partly because currents and voltages of interest in many systems are sinusoidal or very nearly so, at least over some time interval. Examples of such systems are electric power systems and many communication and control systems. But more important, any current or voltage (or any other physical quantity) can be expressed as a sum of sinusoidal currents or voltages using Fourier analysis.1 Consequently, the response of a linear circuit to sinusoidal excitation can tell us a great deal about the response of the circuit to any excitation. For this reason, tools for analysis of sinusoidally excited circuits are far more potent and useful than they might appear to be. They are tools you must master if you wish to design circuits and systems for communication, control, signal processing, and power generation and distribution. We begin by establishing certain conventions regarding sinusoidal voltages and currents. For economy, we use signal to mean current or voltage.
12.1 Sinusoidal Voltages and Currents The standard form of a sinusoidal signal (a sinusoidal current or voltage) is xðtÞ ¼ X cosð2 p f t þ yÞ ¼ X cosðot þ yÞ;
where xðtÞ is the instantaneous amplitude of the sinusoid (V or A), X is the peak amplitude of the sinusoid (V or A), 2 p ft þ y is the instantaneous phase of the sinusoid (rad),