LIGNITES OF NORTH AMERICA
COAL SCIENCE AND TECHNOLOGY Series Editor:
Larry L. Anderson Department of Fuels Engineeri...
51 downloads
2167 Views
36MB Size
Report
This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
Report copyright / DMCA form
LIGNITES OF NORTH AMERICA
COAL SCIENCE AND TECHNOLOGY Series Editor:
Larry L. Anderson Department of Fuels Engineering, University of Utah, Salt Lake City, UT 84112, U.S.A. Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol.
l: Geochemistry of Coal (Bou~ka) 2: Fundamentals of Coal Benefication and Utilization (Tsai) 3: Coal: Typology, Chemistry, Physics and Constitution (Van Krevelen) 4: Coal Pyrolysis (Gavalas) 5: Free Radicals in Coals and Synthetics Fuels (Petrakis and Grandy) 6: Coal Combustion Chemistry-Correlation Aspects (Badin) 7: The Chemistry of Coal (Berkowitz) 8: Natural Gas Substitutes from Coal and Oil (Qader) 9: Processing and Utilization of High-Sulfur Coals (Attia, Editor) 10: Coal Science and Chemistry (Volborth, Editor) 11:1987 International Conference on Coal Science (Moulijn, Nater and Chermin, Editors) Vol. 12: Spectroscopic Analysis of Coal Liquids (Kershaw, Editor) Vol. 13: Energy Recovery from Lignin, Peat and Lower Rank Coals (Trantolo and Wise, Editors) Vol. 14: Chemistry of Coal Weathering (Nelson, Editor) Vol. 15: Advanced Methodologies in Coal Characterization (Charcosset, Editorassisted by Nickel-Pepin-Donat) Vol. 16: Processing and Utilization of High-Sulfur Coals III (Markuszewski and Wheelock, Editors) Vol. 17: Chlorine in Coal (Stringer and Banerjee, Editors) Vol. 18: Processing and Utilization of High-Sulfur Coals IV (Dugan, Quigley and Attia, Editors) Vol. 19: Coal Quality and Combustion Performance: An International Perspective (Unsworth, Barratt and Roberts) Vol. 20: Fundamentals of Coal Combustion for Clean and Efficient Use (Smoot, Editor) Vol. 21: Processing and Utilization of High-Sulfur Coals V (Parekh and Groppo, Editors) Vol. 22: Atmospheric Fluidized Bed Coal Combustion. Research, Development and Application (Valk, Editor) Vol. 23: Lignites of North America (Schobert)
COALSCIENCEAND TECHNOLOGY23
L/GNITES OF NORTH AMERICA HAROLD H. SCHOBERT Fuel Science Program, The Pennsylvania State University, University Park, PA 16802-2303, U.S.A.
1995 ELSEVIER Amsterdam - Lausanne - New York-
Oxford-
Shannon - Tokyo
ELSEVIER SCIENCE B.V. Sara B urgerhartstraat 25 P.O. Box 211, 1000 AE Amsterdam, The Netherlands
ISBN: 0-444-89823-9
9 1995 Elsevier Science B.V. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of the publisher, Elsevier Science B.V., Copyright & Permissions Department, P.O. Box 521, 1000 AM Amsterdam, The Netherlands. Special regulations for readers in the USA. This publication has been registered with the Copyright Clearance Center Inc. (CCC), Salem, Massachusetts. Information can be obtained from the CCC about conditions under which photocopies of parts of this publication may be made in the USA. All other copyright questions, including photocopying outside of the USA, should be referred to the publisher No responsibility is assumed by the publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, products, instructions or ideas contained in the material herein. This book is printed on acid-free paper. Printed in The Netherlands
This book is dedicated to the memory of two lignite researchers who made numerous contributions to lignite science and technology, who freely gave of their time and knowledge to answer questions and to help me, and, most importantly, who were my friends--
Wayne Kube Merle Fegley
This Page Intentionally Left Blank
vii
PREFACE
This book is intended to provide a comprehensive survey of the origin, the fundamental properties, and the technology of utilization of the lignites of North America. I have presumed that the most likely users of this book will be professional scientists and engineers working in some field of coal research or coal technology. Thus I have made no attempt to explain terms that I consider likely to be part of the working vocabulary of such persons. I hope that most persons just coming into the field, with little or no prior exposure to the terminology and conventions of the field, will nevertheless find most of the material reasonably accessible. Coals of course display a continuum of properties, often with no sharp, step change between ranks. In writing about lignites of North America, it would have been all too easy to allow the manuscript to balloon to even larger size by including throughout the text comparisons of the properties and behavior of lignites with those for coals of other ranks. In an effort to keep an enormous amount of information under some sort of control, I have, to a great extent, restricted the discussion strictly to lignites, although I have included some occasional comparisons with other coals, especially brown coals and subbituminous coals. Although there are some interesting distinctions among coals based on their geographic distribution, in many situations coals of comparable rank and composition show similar behavior regardless of their geographic source. A second constraint, therefore, in writing about lignites of North America has been the exclusion of most (but not all) information about lignites from other parts of the world. As I have done in comparing lignites with other ranks of coals, I have occasionally made reference to results on lignites from elsewhere in the world, mainly to point out how North American lignites often show similarities to other lignites. Much excellent work on lignites is being done around the world, and the North American coal scientist or engineer could profit from following it. As this book began to take shape, it seemed to me that only the most ardent of lignitophiles would ever be likely to read it straight through. Rather, I suspect that many persons will dip into the selected chapters or sections most relevant to their immediate interests. For that reason, I have tried to make extensive references to the original work. This book has 1,830 citations to the literature. Unfortunately, much of that original work has often appeared previously only in "obscure government reports" (to borrow a charming phrase coined by a reviewer of one of my papers). I have tried to include sufficient information on experimental conditions and scale of work (that is, whether bench-, pilot-, or commercial-scale) so that the reader can judge whether or not the material is pertinent to his or her interest, and, if appropriate, follow it further into the original literature. The very extensive index is a further effort to make the contents of the book easily
viii accessible to the reader. We who work on coal suffer from having no systematic nomenclature for naming coals. Some authors name the lignite on the basis of seam, others on the basis of formation, others on the basis of its county of origin, and still others on the basis of the mine. Furthermore, some mines have been closed since the lignite was studied and reported on, and in some states or regions the names of geological formations and units have been changed over the years. In some papers, the authors refer simply to, e.g., "a North Dakota lignite," or to the even more awful "a lignite." As a result, the coal literature is a welter of confusing, occasionally colorful, and sometimes bizarre, names. One option for dealing with this mess would have been to impose my own system of order, to decide, for example, that all lignites would be named on the basis of the mine, or, say, on the county from which they come. It seemed to me, however, that the potential for the inadvertent introduction of error was enormous. I have instead reported the name of the lignite as it was used in the original literature. To be sure, this approach perpetuates a mess, but obviates the potential for generating an even more colossal mess by giving some lignites the names of things they are not. I have reported numerical data almost entirely in SI units, except for temperatures, which are generally given as degrees Celsius rather than kelvins. For readers who have been steeped in English units and find SI units strange, I would say simply that it's time to learn. The only situations in which English units have been retained are equations that have constants or coefficients that were derived from the fitting of original data that also had English units. In such cases I felt as I did with the issue of nomenclature--the prospects for inadvertent introduction of error by an attempted "correction" outweighed the discomfort of retaining the obsolete units. In those instances I have tried clearly to state in the accompanying text the appropriate units to use. The writing of this book has been a long and arduous undertaking. Throughout, I have been helped greatly by many persons who have given me access to materials in their personal collections, who have answered questions, and who have given advice on miscellaneous computer problems. I particularly thank my present and former colleagues at Penn State, and the members of what used to be the Coal Science Division ( a group for whom the term used above, "occasionally colorful, and sometimes bizarre," is most apt) at what used to be the University of North Dakota Energy Research Center. I am pleased to acknowledge a pleasant and, to me, quite helpful correspondence with Olav Schmitz of Elsevier, and to several generations of patient Elsevier editors, several of whom, I think, gave up in despair. This book has been prepared entirely on my own time with my own resources. Any statements of opinion, or any editorializing, are mine alone, and do not necessarily reflect the positions either of The Pennsylvania State University or of Elsevier. Of course I take full responsibility for any errors in the book. Harold H. Schobert
University Park, Pennsylvania
iX
CONTENTS
Preface .........................................................................................
C h a p t e r 1. T h e p r i n c i p a l lignite d e p o s i t s o f N o r t h A m e r i c a ............................. 1.1. 1.2.
1.3.
Introduction The
Gulf
....................................................................
region
1.2.1.
Texas
1.2.2. 1.2.3.
lignites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1 1 4
.................................................................
4
Alabama
..............................................................
12
Arkansas
.............................................................
15
1.2.4.
Louisiana
.............................................................
16
1.2.5.
Mississippi
...........................................................
18
1.2.6.
Tennessee
The
Fort
Union
............................................................
region
1.3.1.
North
1.3.2.
Montana
Dakota
.........................................................
19 19
........................................................
19
..............................................................
28
1.3.3.
Saskatchewan
........................................................
34
1.3.4.
South
........................................................
35
Dakota
1.4. O t h e r l i g n i t e s o f the U n i t e d S t a t e s ............................................ 1.4.1.
California
.............................................................
1.4.2.
The
Rocky
Mountains
1.4.3.
The
Plains
states
The
Northwest
1.4.4. 1.5.
vii
Other
lignites
Ontario
1.5.2.
British
1.5.3.
The
1.5.4.
Nova
References
..............................................
41 42
.......................................................
42
.......................................................
43
................................................................
43
Columbia
Canadian Scotia
....................................................
Arctic
................................................
44 45
C h a p t e r 2. T h e d e p o s i t i o n a n d f o r m a t i o n o f lignite ........................................ Introduction
2.2.
Paleoflora
44
..........................................................
.............................................................................
2.1.
39
.....................................................
of Canada
1.5.1.
39
46
51
......................................................................
51
........................................................................
51
2.2.1. N o r t h e r n G r e a t P l a i n s p a l e o f l o r a ..................................
51
2.2.2.
52
Gulf Coast
paleoflora
...............................................
2.3.
Environments
of deposition
...................................................
2.3.1.
Fluvial
environments
...............................................
55
2.3.2.
Deltaic
environments
................................................
58
.............................................
59
2.3.3.
Lagoonal
2.3.4.
Backswamp
environments
2.3.5.
Marsh
2.3.6.
Lacustrine
environments
environments
.........................................
59
................................................
61
environments
...........................................
2.4. T r a n s f o r m a t i o n o f p l a n t material to lignite ................................... 2.4.1.
Introduction
2.4.2.
Loss
..........................................................
of cellulose
....................................................
2.4.3. S t r u c t u r a l e v o l u t i o n o f l i g n i n r e s i d u e s ............................ 2.4.4. E v o l u t i o n o f the c a r b o n s k e l e t o n .................................
63 65 66 68
2.4.6.
71
Sulfur
................................................................. o f m e t a l i o n s ........................................
.............................................................................
C h a p t e r 3. T h e o r g a n i c s t r u c t u r e o f l i g n i t e s ................................................
3.3.
63
7O
References
3.2.
62
2.4.5. T r a n s f o r m a t i o n s o f o x y g e n f u n c t i o n a l g r o u p s ...................
2.4.7. Accumulation
3.1.
54
Petrography
of lignites
3.1.1.
Lithologic
3.1.2.
Lithotypes
3.1.3.
Macerals
The
carbon
.........................................................
72 74
79 79
..................................................
79
............................................................
81
..............................................................
85
layering
skeleton
............................................................
92
3.2.1.
Aromatic
carbon
.....................................................
92
3.2.2.
Aliphatic
carbon
.....................................................
101
.....................................................................
109
Heteroatoms 3.3.1.
Introduction
..........................................................
109
.............................................
109
..........................................................
113
3.3.2.
Carboxylic
3.3.3.
Humic
acid groups
3.3.4.
Methoxyl
....................................................
114
3.3.5.
Phenolic
groups
.....................................................
115
3.3.6.
Carbonyl
groups
....................................................
116
acids
groups
.........................................
116
..........................................................
118
3.3.7. Ethers other than methoxyl 3.3.8. 3.3.9.
Ester
groups
C e l l u l o s e a n d l i g n i n r e s i d u e s .......................................
3.3.10.
Nitrogen
groups
3.3.11.
Sulfur
3.3.12.
Chlorine
118
....................................................
121
.......................................................
122
.............................................................
123
3.4. T h e t h r e e - d i m e n s i o n a l s t r u c t u r e o f lignite ...................................
123
groups
xi 3.4.1. E v i d e n c e for a colloidal structure ..................................
123
3.4.2. C r o s s l i n k i n g in lignite structures ..................................
124
3.4.3. M o l e c u l e s trapped in the lignite structure .........................
126
3.4.4.
D e p o l y m e r i z a t i o n r e a c t i o n s .........................................
129
.............................................................................
130
References
C h a p t e r 4. F u n d a m e n t a l organic reaction chemistry of lignites ...........................
139
4.1. R e a c t i o n s w i t h c a r b o n m o n o x i d e ..............................................
139
4.1.1. Reactions of c a r b o n m o n o x i d e with lignite .......................
139
4.1.2. S u p p o r t i n g m o d e l c o m p o u n d studies .............................
142
4.1.3. C a r b o n m o n o x i d e - h y d r o g e n m i x t u r e s ..........................
144
4.1.4. C a r b o n m o n o x i d e - steam m i x t u r e s ...............................
145
4.2.
Reactions
with
hydrogen
.......................................................
4.2.1. H y d r o p y r o l y s i s and hydrogasification reactions .................
149
4.2.2. R e a c t i o n s u n d e r liquefaction conditions ...........................
158
4.3. R e a c t i o n s in o t h e r g a s e o u s a t m o s p h e r e s ...................................... 4.3.1.
4.4.
149
Oxidation
160
...................................................
160
4.3.2. R e a c t i o n s with w a t e r or steam ......................................
164
4.3.3. R e a c t i o n s with sulfur c o m p o u n d s ..................................
169
Pyrolysis
reactions
of lignites
4.4.1.
Heats
4.4.2.
Kinetics
.............................................................
of reaction
.....................................................
of pyrolysis
172 172
................................................
173
4.4.3. C o m p a r a t i v e effects of gaseous a t m o s p h e r e s ....................
177
4.4.4. Effects of lignite moisture content on pyrolysis .................
179
4.4.5. Effects of cations on lignite pyrolysis ............................
179
4.4.6. E f f e c t s o f p e t r o g r a p h i c c o m p o s i t i o n ..............................
184
4.4.7. Changes in physical structure a c c o m p a n y i n g pyrolysis ........
186
4.4.8. C h a n g e s in functional groups during pyrolysis .................
188
4.4.9. E v o l u t i o n of products during pyrolysis ..........................
194
References
.............................................................................
207
C h a p t e r 5. T h e i n o r g a n i c c o n s t i t u e n t s o f lignites ..........................................
218
5.1. I n c o r p o r a t i o n o f m a j o r e l e m e n t s ..............................................
218
5.1.1. A c c u m u l a t i o n of inorganic c o m p o n e n t s ..........................
218
5.1.2.
Chemical
..............................................
220
5.1.3.
The
5.2.
Minerals
in
fractionation
major elements lignites
5.2.1.
Introductory
5.2.2.
Sulfide
.................................................
230
.............................................................
239
overview
..............................................
239
.....................................................
242
minerals
xii
5.3.
minerals
.......................................................
244
5.2.3.
Oxide
5.2.4.
Carbonate
minerals
..................................................
245
5.2.5.
Phosphate
minerals
.................................................
246
5.2.6.
Sulfate
minerals
.....................................................
246
5.2.7.
Silicate
minerals
.....................................................
247
5.2.8.
Oxalate
minerals
.....................................................
250
..................................................................
250
Trace
elements
5.3.1.
Introduction
5.3.2.
Alkali
5.3.3.
Alkaline
..........................................................
250
.........................................................
251
metals
.......................................................
253
5.3.4. F i r s t - r o w t r a n s i t i o n m e t a l s .........................................
254
5.3.5.
257
5.3.6.
earths
H e a v y t r a n s i t i o n m e t a l s ............................................. ..........................................................
258
.............................................................
259
Lanthanides
5.3.7.
Actinides
5.3.8.
Group
lib elements
.................................................
263
5.3.9.
Group
III e l e m e n t s
..................................................
263
5.3.10.
Group
IV e l e m e n t s
................................................
263
V elements
.................................................
265
.........................................................
265
............................................................
265
5.4. V a r i a b i l i t y o f i n o r g a n i c c o m p o s i t i o n .........................................
266
5.3.11.
Group
5.3.12.
Chalcogens
5.3.13.
Halogens
5.4.1.
Introduction
..........................................................
266
5.4.2. Factors affecting the inorganic composition of lignites .........
266
5.4.3. Vertical v a r i a b i l i t y within s e a m s ...................................
271
5.4.4.
...................................................
275
5.4.5. State and regional v a r i a b i l i t y .......................................
278
References
In-mine
variability
.............................................................................
C h a p t e r 6. B e h a v i o r o f inorganic c o m p o n e n t s of lignites .................................
281
290
........................................................
290
6.2. R e a c t i o n s o f e x c h a n g e a b l e cations .............................................
293
6.1.
Low-temperature
ashing
6.2.1. R e a c t i o n s during ashing or c o m b u s t i o n ...........................
293
6.2.2. B e h a v i o r of c a l c i u m in lignite liquefaction ........................
297
6.3. M i n e r a l reactions at e l e v a t e d t e m p e r a t u r e s ....................................
298
6.3.1.
Anhydrite
..............................................................
298
6.3.2.
Bredigite
...............................................................
299
..................................................................
299
6.3.3.
Calcite
..................................................
299
6.3.5. G e h l e n i t e - a k e r m a n i t e series ........................................
301
6.3.4.
Feldspathic
minerals
xiii 6.3.6.
Hematite
................................................................
301
6.3.7.
Hercynite
...............................................................
302
6.3.8.
Kaolinite
.................................................................
302
6.3.9.
Magnetite
...............................................................
303
6.3.10.
Pyrite
..................................................................
303
6.3.11.
Quartz
.................................................................
304
silicates
6.3.12.
Sodium
.....................................................
305
6.3.13.
Sulfur
......................................................
305
6.3.14.
V o l a t i l i z a t i o n d u r i n g a s h i n g ........................................
306
6.4. T h e r m a l p r o p e r t i e s o f ashes and slags .........................................
307
retention
6.4.1.
Specific
heat
6.4.2.
Radiative
heat transfer
6.5.
Sintering
6.6.
Ash
........................................................... ................................................
307 307
...........................................................................
309
.........................................................................
316
fusion
6.7. S l a g v i s c o s i t y a n d s u r f a c e tension ..............................................
320
6.7.1. L a b o r a t o r y data on slag viscosity ...................................
320
6.7.2. C a l c u l a t i o n o f viscosity f r o m c o m p o s i t i o n .........................
327
6.7.3. A p p l i c a t i o n s o f viscosity data in lignite processing ...............
335
6.7.4.
335
References
Surface
tension
........................................................
..............................................................................
337
C h a p t e r 7. P h y s i c a l p r o p e r t i e s o f lignites ...................................................
343
7.1.
Bulk
mechanical
7.1.1. 7.1.2.
Friability
Grindability
7.1.5.
7.3.
7.4.
Density
.....................................................
shrinkage
7.1.3. 7.1.4.
7.2.
properties
Volumetric
................................................
..............................................................
343 343 345
..........................................................
351
.............................................................
354
F r e e sliding s h e a r s t r e n g t h .........................................
355
Hardness
...........................................................................
357
7.2.1. D e n s i t y m e a s u r e m e n t s by i m m e r s i o n in fluids ...................
357
7.2.2.
Bulk
357
7.2.3.
Mercury
7.2.4.
Helium
Thermal
density
..........................................................
densities
....................................................
357
.....................................................
358
..............................................................
358
densities
properties
7.3.1.
Specific
heat
7.3.2.
Thermal
conductivity
Surface
358
................................................
359
.......................................................
360
o f s u r f a c e a r e a ........................................
360
area and porosity
7.4.1. M e a s u r e m e n t 7.4.2.
..........................................................
Porosity and pore volume
...........................................
365
xiv 7.4.3.
H y d r a u l i c conductivity ...............................................
368
7.4.4. Effects of heating on surface area and porosity ...................
368
7.4.5. The fractal structure of lignite .......................................
372
References
..............................................................................
C h a p t e r 8. Moisture in lignite .................................................................. 8.1.
Introduction
8.2.
Equilibrium
....................................................................... moisture
............................................................
378
383 383 385
8.3. Measurement of moisture by elevated-temperature methods ................
387
8.4. Evidence for bimodal incorporation of water .................................
391
8.5. Adsorption and desorption of moisture ........................................
396
8.6. Heat of wetting in water .........................................................
405
References
4O6
..............................................................................
Chapter 9. Mining, transportation, and storage ............................................. 9.1.
Lignite mining
....................................................................
410 410
9.1.1. Historical development of lignite mining ..........................
410
9.1.2. Overview of surface mining .........................................
412
9.1.3. Preliminary steps in opening a mine ...............................
415
9.1.4.
O v e r b u r d e n removal
.................................................
416
9.1.5.
L i g n i t e removal
.......................................................
421
9.1.6. M i n e d - l a n d reclamation ..............................................
423
9.1.7. Specific examples of mining practices ..............................
424
9.2.
Transportation
...................................................................
429
9.3.
H a n d l i n g and storage ...........................................................
432
9.3.1.
Handling of lignite ..................................................
432
9.3.2.
Stockpiling
433
...........................................................
9.3.3. Low-temperature air oxidation .....................................
436
9.3.4. Autogenous heating and combustion ..............................
436
9.3.5. Storage of dried lignite ..............................................
AAA
9.3.6.
446
Dust explosions
......................................................
.............................................................................
446
C h a p t e r 10. Beneficiation of lignite .........................................................
451
References
10.1.
Drying
..........................................................................
451
......................................................
451
10.1.2. Entrained and fluidized drying ...................................
457
10.1.3.
H o t - w a t e r drying ..................................................
457
10.1.4. Steam and hot-water drying ......................................
463
10.1.1.
Rotary
drying
xv 10.1.5.
Steam
drying
.......................................................
465
..................................................
467
in hot oil ...................................................
473
10.2. R e m o v a l o f m i n e r a l m a t t e r ...................................................
474
10.1.6.
Fleissner
10.1.7.
Drying
process
10.2.1.
Introduction
........................................................
10.2.2.
Gulf Coast lignites
474
.................................................
475
10.2.3. N o r t h e r n G r e a t Plains lignites ....................................
477
10.3. R e m o v a l of inorganic constituents by ion e x c h a n g e ......................
480
10.3.1.
Introduction
480
10.3.3.
Bench-scale
...................................................
483
10.3.4.
Pilot-scale
Desulfurization
10.5.
Size
10.7.
480
10.3.2. F u n d a m e n t a l s o f ion e x c h a n g e with lignites ....................
10.4.
10.6.
........................................................
tests
.....................................................
486
.................................................................
487
tests
................................................................
489
10.5.1. Size r e d u c t i o n at the m i n e .........................................
489
10.5.2. P u l v e r i z a t i o n for c o m b u s t i o n .....................................
491
10.5.3.
492
preparation
Micropulverization
Briquetting
.................................................
.....................................................................
493
10.6.1. L a b o r a t o r y and pilot-scale studies ................................
493
10.6.2.
............................................
496
..........................................................
497
Commercial
Lignite/water
briquetting
slurries
.............................................
497
10.7.2. R h e o l o g y of l i g n i t e / w a t e r slurries ................................
499
10.7.3. Solids loadings of lignite/water slurries .........................
499
10.7.1.
References
Pilot-scale preparation
.............................................................................
499
o f lignites .........................................................
505
11.1. F u n d a m e n t a l s of lignite c o m b u s t i o n ........................................
505
11.1.1. C a l o r i f i c v a l u e s of lignites ........................................
505
11.1.2. M e c h a n i s m s o f c o m b u s t i o n ......................................
507
11.1.3. I n o r g a n i c transformations during c o m b u s t i o n .................
515
Chapter
11. C o m b u s t i o n
11.2. S m a l l - s c a l e c o m b u s t i o n 11.2.1.
Historical
s y s t e m s ............................................ ............................................
521
11.2.2. D o m e s t i c use o f lignite ............................................
521
11.2.3.
........................................................
522
p r a c t i c e .................................................
527
Stoker
development
521
firing
11.3. C u r r e n t c o m b u s t i o n
11.3.1. Historical d e v e l o p m e n t of pulverized firing of lignite .........
527
11.3.2. Evaluation of lignites as potential fuels for p o w e r plants .....
528
11.3.3. C o m m e r c i a l firing for p o w e r generation ........................
531
xvi 11.3.4. S u r v e y of current commercial practice ..........................
534
11.3.5. Emission control technology
.......................................
543
11.4. A s h deposition, slagging and corrosion ....................................
544
11.4.1.
11.5.
........................................................
544
11.4.2. Factors affecting fouling and slagging ..........................
Introduction
546
11.4.3. T h e m e c h a n i s m of deposition ....................................
56O
11.4.4. G r o w t h of strength in deposits ...................................
572
11.4.5. Remedial measures for combatting fouling and slagging .....
575
11.4.6.
..............................................
582
....................................................
583
.........................................................
583
Ash-related corrosion
Fluidized-bed 11.5.1.
combustion
Introduction
11.5.2.
Combustion
behavior
..............................................
585
11.5.3.
I n - b e d s u l f u r capture
...............................................
585
11.5.4.
NOx
......................................................
588
11.5.5. References
Bed
formation
agglomeration
..................................................
589
.............................................................................
591
C h a p t e r 12. A l t e r n a t i v e uses of lignites .....................................................
602
12.1.
o f lignite .........................................................
602
12.1.1. F u n d a m e n t a l s of gasification .....................................
602
12.1.2. C o m m e r c i a l gasification in North A m e r i c a .....................
614
12.1.3. C o m m e r c i a l gasification outside North A m e r i c a ...............
622
Gasification
12.1.4. Pilot-scale gasification of lignites ................................
624
12.1.5. U n d e r g r o u n d gasification of lignite .............................
637
12.1.6. Biological gasification of lignites ................................
638
12.2. Direct l i q u e f a c t i o n of lignites ................................................
639
12.2.1. T h e E x x o n D o n o r Solvent process ..............................
639
12.2.2.
643
Project
Lignite
12.2.3. T h e C O - S t e a m
...................................................... process ............................................
648
............................................
651
12.2.5. Bench-scale studies for process i m p r o v e m e n t .................
652
12.3. C h e m i c a l products from lignites .............................................
655
12.2.4. T w o - s t a g e
12.3.1.
Montan
12.3.2.
Activated
liquefaction
wax
........................................................
655
...................................................
656
12.3.3. Direct uses of lignites in water treatment ........................
658
12.3.4.
658
Charcoal
carbon
............................................................
12.3.5. Applications in extractive m e t a l l u r g y ............................
659
12.3.6. R e c o v e r y of uranium from lignites ..............................
661
12.3.7.
663
Leonardite
..........................................................
xvii 12.3.8. Prospects for other chemical products from lignites ............
665
12.3.9. A p p l i c a t i o n s of lignite ashes .......................................
666
12.4. C o m b u s t i o n of lignite-water slurries .........................................
666
12.4.1. Slurry preparation for c o m b u s t i o n .................................
666
12.4.2.
Combustion
...........................................
667
12.4.3.
Ash
.........................................................
667
References
Index
performance
behavior
..............................................................................
669
............................................................................................
679
This Page Intentionally Left Blank
Chapter 1
THE P R I N C I P A L LIGNITE DEPOSITS OF NORTH A M E R I C A
1.1 I N T R O D U C T I O N This chapter describes the lignite deposits of North America, providing information on the estimated reserves and resources, the geological setting of the deposits, and the quality of the lignites. Two major deposits of lignites exist in North America. The Gulf Coast lignites occur in the southeastern United States, in deposits lying in a band roughly parallel to the coastline of the Gulf of Mexico, forming an arc stretching from southern Texas across Louisiana and Mississippi into Alabama. The second major deposit is the Fort Union lignite field, lying in the northern Great Plains in portions of North Dakota, Montana, and Saskatchewan. The Gulf Coast and Fort Union lignites represent the largest proportion of reserves and resources of lignites in North America, are the most important commercial sources of lignites, and are those which have been most extensively studied. Hence most of this chapter is devoted to a discussion of these lignites. Smaller deposits of lignites occur outside the Gulf and Fort Union regions. Some information on these lignites is also presented in this chapter. Even though the reserve base of these lignites is much smaller and in many cases the deposits have not been as well studied, some have commercial potential and all are worthy of additional investigation. Estimated lignite reserves and resources in the United States are shown in Table 1.1 [ 1]. In addition, the principal Canadian lignite deposit, in Saskatchewan, includes 35.2 Gt of in-place resources [2]. The remaining reserves of U. S. lignite able to be recovered by strip mining are shown, by state, in Table 1.2 [3]. The same information is shown by coal province in Table 1.3 [3].
TABLE 1.1 U.S. lignite reserves and resources, gigatonnes [1].
Region
Strippable Reserve Base
Fort Union North Dakota Montana South Dakota Total Gulf Texas Alabama Arkansas Louisiana Total Denver Other states Total ........................
Identified Resources
9.2 14.3 0.4 23.9
318.1 102.1 2.0 422.2
7.2 1.0 1.8 0.5 10.5 2.6
47.4 1.8 12.2 0.5 61.9 9.1 0.2 37.0 ............. 493.4
TABLE 1.2 Remaining U. S. lignite reserves recoverable by strip mining, Mt [3]. State Reserves California 23 Colorado 907 Montana 15,168 North Dakota 11,839 South Dakota 300 Texas 8,618 Washington 5 Wyoming 454 Total ............... 37,314
TABLE 1.3 Remaining lignite reserves in coal provinces recoverable by strip mining, Mt [3]. Province Reserves Coastal Plains 8,618 Great Plains 19,456 Pacific Coast- Sierra Nevada 27 Wyoming Basins 9,213 T otal ............................... 37,314
About 10% of all U. S. low-rank coals (including subbituminous) are classified as the strippable
reserve base [4]. For lignites, the strippable reserve base is 37.0 Gt, and the total identified resources are 493.4 Gt [4]. Data on the reserve base of lignites, organized by state, county, bed, and thickness, is available in [5]. The identified resources of U. S. lignites are classified by depth of seam in Table 1.4 and by seam thickness in Table 1.5 [6]. Identified resources are classified by sulfur content in Table 1.6 and by ash in Table 1.7 [6]. In both tables, the data are shown as weight percent on an as-received basis. In the sections which follow, the principal lignite deposits of each state or province are discussed. The first two sections discuss the Gulf and Fort Union region lignites, with shorter sections treating some of the other lignite deposits. Most of the discussion is devoted to the lignites of Texas, North Dakota, and Montana, since these are the most important deposits in commercial use. A few very small deposits of lignites, having no evident commercial potential but of interest for the geochemistry and organic structure of lignites, are treated briefly in other chapters. T A B L E 1.4 U.S. identified lignite resources (gigatonnes) classified by depth [6].
Depth of Lignite Seam (meters) Region 0-305 305-610 Unknown Total Fort Union 333.6 88.5 422.1 Gulf 39.0 23.0 62.0 Denver 9.1 9.1 Other states 0.2 0.2 Totals ..... 381.7 ............. 23.0 ........... 88.7 .......... 493.4
T A B L E 1.5 U.S. identified lignite resources (gigatonnes) classified by seam thickness [6].
Seam Thickness (meters) Region 0-3 3--6 >6 Unknown Total Fort Union 6.1 11.8 10.2 394.1 422.1 Gulf 21.5 2.4 0.2 37.9 62.0 Denver 9.1 9.1 Other states 0.2 0.2 Totals .......... 27.6 ........... 14.2 ........... 10.4 ........... 441.3 ......... 493.4
TABLE 1.6 U.S. identified lignite resources (gigatonnes) classified by sulfur content (weight percent asreceived basis) [6].
Region Fort Union Gulf Denver Other states Totals .........
0-- 1 422.1 58.4 9.1 489.6
Sulfur Content, as-received 1-3 >3 1.8
Unknown
1.8
........ 1.8 ............. 1.8 ...........
0.2 0.2 ...........
Total 422.1 62.0 9.1 0.2 493.4
TABLE 1.7 U.S. identified lignite resources (gigatonnes) classified by ash value (weight percent as-received basis) [6]. ...... Ash, as-received Region 5-10 > 10 Unknown Total Fort Union 422.1 422.1 Gulf 18.2 43.8 62.0 Denver 9.1 9.1 Other states 0.2 0.2 Totals .............. 440.3 ......... 43.8 .......... 9.3 ............ 493.4
1.2 T H E G U L F R E G I O N
LIGNITES
1.2.1 Texas (i) History. The first scientific description of lignite in Texas was published in 1839 [6]. Small-scale production for local use began in the 1850's [7]. Production reached 1.4 Mt in 1914 [8], but then declined steadily to 1950, when it dropped below 18,000 tonnes. Before World War II, lignite was mined in many counties, in a band from Medina County northeastward to Louisiana. Around the turn of the century, lignite mined near Calvert Bluff was blended with bituminous coal as a locomotive fuel [9]. A use of lignite probably unique to Texas was combustion for process heat needed in the production of salt [10]. Mining in the vicinity of Darco (Harrison County) for activated carbon production started in 1931. Over the years lignite was gradually supplanted as a fuel source by natural gas and petroleum. Mining of lignite as fuel ceased in 1946 [11]. Some mining continued, however, for lignite used as a feedstock for activated carbon production. Mining for fuel use resumed in 1955 with the opening of a large power plant at Sandow (Milam County) to supply power to Alcoa for aluminum refining. Production began increasing sharply in the 1960's. (ii) Occurrence. Texas possesses the largest lignite resources of the Gulf Coast states, as shown in Table 1.8 [ 12]:
TABLE 1.8 Gulf Coast lignite resources by state, gigatonnes [12].
State Alabama Arkansas Louisiana Mississippi Tennessee Texas
Resources* 1.27 2.27 1.54 4.54 0.91 21.23
*Estimated in-place tonnage of seams greater than 1 m thick to 60 m deep. The resources of Texas lignite are summarized by geologic unit and region in Table 1.9 [13]. In Texas, lignite occurs in three stratigraphic units of Eocene age: the Wilcox and Jackson Groups and the Yegua Formation [ 14,15]. TABLE 1.9 Texas lignite resources (megatonnes) [ 13]. Geologic Unit Wilcox
Resources Re~ion Near-surface Deep-basin East-Central 5,880 5~,940 Northeast 4,626 0 Sabine Uplift 3,549 4,959 South 978 4,201 subtotal .............. 15,032 ........ 15,100 ....... Jackson East 4,081 5,080 South 687 4,785 subtotal ................ 4,768 ....... 9,124 ....... Yegua East 1,407 0 T O T A L ........................ 21,208 ....... 24,966 .......
Total 11,820 4,626 8,508 5,179 30,133 9,162 5,472 14,634 1,407 46,174
The potential near-surface resources at depths less than 60 m [14], amenable to conventional surface mining, and in seams 0.9 m or thicker, are 21.2 Gt [15]. About 70% of the near-surface lignite occurs in the Wilcox, about 23% in the Jackson and 7% in the Yegua [14]. More than 90% of this lignite occurs in the Wilcox and Jackson Groups north of the Colorado River [ 14]. The average seam thickness is less than 1.5 m, with a seam of 3 m being exceptional [15]. Wilcox lignite is the best quality, having a calorific value of 15.1 MJ/kg, 33% moisture, 1% sulfur, and 15% ash [ 15]. Yegua lignite is intermediate in quality and Jackson is the poorest. Near-surface lignite occurs in three areas: a continuous band running approximately southwest to northeast from the Rio Grande River in Webb County, passing south of San Antonio, Austin and Waco to Texarkana; a second band which is roughly parallel to the first, from the Rio Grande in Starr County to the Angelina River; and an irregularly shaped deposit in Panola County
and the surrounding region [16]. Near-surface lignite occurs in the main lignite-bearing rocks in an area centered on Panola and adjacent counties of the Sabine Uplift. Near-surface lignite also occurs in two bands, a northern band continuous from the Rio Grande River in Webb County to the Red River in Bowie County; and a parallel, but discontinuous, band lying coastward and stretching from the Rio Grande River in Starr County to the Angelina River in Angelina County. The northern band is divided into three regions [17]: South, from Webb to Caldwell counties; Central, from Bastrop through Freestone counties; and East, from Henderson through Bowie counties and the Sabine Uplift. The coastward band has two regions [ 17]: South, Atascosa, LaSalle, McMullen, Starr, and Zapata counties; and Southeast, from Fayette County through Angelina County. The near-surface lignite resource strata are divided into seven units on a geographic basis; resources according to these units are shown in Table 1.10 [18]. The Wilcox Group accounts for 71% of the total tonnage and 77% of the resource on a calorific value basis. TABLE 1.10 Resources of near-surface lignite in Texas, megatonnes [18]. Region Central Wilcox Northeast Wilcox Sabine Uplift Wilcox South Wilcox East Jackson South Jackson East Claiborne Total ...........................
Resource 5,880 4,626 3,549 978 4,081 687 1,407 21,208
The thickest, most laterally continuous deposits are in the Wilcox of central Texas and the central region of the Sabine Uplift, and in the east Jackson. Some Wilcox seams are laterally continuous for 27 km; some Jackson seams, for up to 48 km [18]. Typical seam thickness is about 3 m, though in some areas seams may reach 4.6 m [ 18]. The largest resource blocks are 900 Mt in the east Jackson and 450 Mt in the central Wilcox. Seams in the northeast Wilcox and the northern Sabine Uplift are thinner, usually less than 2.4 m, but resource blocks of up to 450 Mt are present [18]. In the Yegua Formation seams are usually less than 1.8 m and are discontinuous; resource blocks are 136 Mt or less. South of the Colorado River the Jackson Group has resource blocks of up to 272 Mt [ 18]. Deep-basin lignite is that which occurs under more than 60 m of cover [14]. The resources lying between 60 and 1,524 m are 90 Gt [17]. About 32 Gt lie between 60 and 600 m [17]. Of this, 69% is in the Wilcox and 31% in the Jackson [18]. Deep-basin lignite is unimportant in the Yegua. Deep-basin lignite occurs coastward and downdip from the near-surface deposits. The principal deep-basin lignite occurs in central and eastern Texas, in an area running from Gonzales County to Cherokee County. In Cherokee County the deep-basin lignite splits into two bands
which curl around the sides of the Sabine Uplift. The deep-basin lignite in south Texas extends in a band from the common border of Jim Hogg, Starr, and Zapata counties to McMullen County [ 16]. Six small isolated areas of deep-basin lignite have also been mapped. The largest is in Washington County. The largest and most extensive deposits of deep-basin lignite are in the Wilcox Group of central Texas. Deep-basin lignites are thickest and most numerous in Bastrop, Fayette, Houston, Lee, Leon, and Madison counties. The eastern half of Texas is underlain by lignite deposits, which dip very slightly toward the coast. The lignite can be mined by stripping in regions close to the outcrops. The amount economically recoverable to 46 m depths is 6.1 Gt, and to 60 m is 8.1 Gt [19]. Although the grade of the lignite is variable, an average calorific value is about 15.1 MJ/kg [19]. Ash and moisture contents are both usually high. The strippable lignite lies between the two major metropolitan belts in Texas, and has potential for future use as a fuel for industrial process heat, in addition to its present use as a fuel for electric power generation. Strippable reserves are estimated at 1.2 Gt [8]. Lignite occurs in the Coastal Plain of Texas, in a band 965 km long and 80 to 160 km wide running southwest to northeast from the Rio Grande to the Sabine rivers [20]. The band tends to parallel the coast line, lying 160 to 240 km inland. The main lignite deposits in Texas occur in the Wilcox Group. Smaller deposits occur in the Y egua Formation and the Jackson Group. The most extensive resources occur in the Wilcox Group in eastern and central Texas generally north of the Colorado River. Essentially all of the lignites are Eocene age, although a few of the Wilcox lignites south of the Colorado River and in the southern part of the Sabine Uplift may be Paleocene [21]. The lignites occur throughout the lower Tertiary but are especially abundant in the lower and middle Eocene. Lignite occurs in 49 counties of eastern and central Texas [22]. The strata associated with the lignite beds are largely clays and unconsolidated sands. The region has a thick covering of soil, so that exposures of bedrock are rare; consequently, the extent and thickness of the lignite beds is usually determined from shallow drill holes or pits. Individual seams vary widely in thickness and quality. Thicknesses range up to 6 m [8]. Virtually all of the lignites contain less than 2% sulfur; most are below 1% [8]. Calorific values range from 16.3 to 20.9 MJ/kg (as-received basis) [8]. (iii)
Quality. Generally
the differences in grade and continuity of seams can be correlated
with the depositional environment [14]. North of the Trinity River the Wilcox lignite occurs in lenticular seams of moderately high ash value but low sulfur, and a maximum thickness of 4.6 m. This lignite accumulated on an ancient alluvial plain. Stream courses were closely spaced, and interchannel basins were fairly small. The associated peat swamps were of restricted area and were vulnerable to flooding, with attendant influx of sediments. South of the Trinity River and on the Sabine Uplift the interchannel basins were formed lower on the alluvial plain and thus were larger and less likely to experience flooding. The Jackson Group lignites accumulated in marshes on the lower delta plain. Blanket peats could form over extensive areas of the abandoned delta lobes. Because these blanket peats lay more to the seaward, they were more likely to be permeated by sulfur-rich waters. These factors result in the Jackson lignites being more laterally continuous and
of higher sulfur content than the Wilcox lignites. The highest quality lignite occurs in the Lower Eocene Wilcox Group north of the Colorado River. In this region the individual seams are thicker, of more uniform quality, and more persistent than in other locations in Texas. Lower quality lignite of the Wilcox, as well as Upper Eocene Yegua and Manning Formations, is found south of the Colorado River. Most Texas lignite is xyloid; over 50% derives from the woody parts of plants [7]. However, Texas lignite commonly contains considerable amounts of attrital material, from residual remains of plant matter chemically or mechanically broken down to microscopic fragments during the early stages of coalification, as well as some decay-resistant parts of plants. On a dry basis, the ash value of Texas lignites ranges from less than 10% to over 40% [7]. The average ash value is about 16% [7,23]. North of the Colorado River the average is less than 15%; some Wilcox lignites in the southern part of the Sabine Uplift yield less than 10% [7]. Lignites with very high ash, occasionally exceeding 40%, occur south of the Colorado River. The Upper Eocene lignites also show a geographic trend in ash value, ranging from 15-20% ash in east Texas to 35% in south Texas [7]. The average calorific value of Texas lignites is 24.2 MJ/kg on a dry basis [7]; it ranges from 27.9 MJ/kg for east Texas lignites to less than 23.2 MJ/kg for lignite in south Texas [7,23]. This change in calorific value tracks the trends discussed above for the geographic distribution of ash. As a rule, if lignites of comparable ash value are compared, those having the higher calorific value have higher fixed carbon and higher carbon and hydrogen contents. Lignites with calorific values above 25.6 MJ/kg are found in the Sabine Uplift, in Lee County to the Trinity River and in Houston and Trinity counties. Medium calorific values (23.2 to 25.2 MJ/kg) are found in lignites from Trinity River to Bowie County, and in Medina, Bastrop, and Fayette counties. South Texas lignites of Eocene age generally have calorific values less than 23.2 M.l/kg. The average fixed carbon content of Texas lignites is 37%, on a dry basis [7]. North of the Colorado River the fixed carbon of Wilcox lignites ranges from 30 to 50%, but south of the fiver these lignites contain less than 30% fixed carbon [7]. For lignites of Upper Eocene age, the fixed carbon is generally 30-40% in east Texas and decreases to less than 30% in south Texas [7]. The volatile matter content decreases toward the south, consistent with the trend for increasing ash content. Lignites having volatile matter exceeding 50% on a dry basis occur from the Trinity River to the Sabine River, in the southern part of the Sabine Uplift, and in Franklin, Bowie, Bostrop, Houston, and Trinity counties. Volatile matter contents in the range of 40 to 50% (dry basis) are found in lignites of Rains, Wood, Hopkins, Fayette, Medina and Caldwell counties, in the northern part of the Sabine Uplift, and from Lee County to the Trinity River. The South Texas lignites of Eocene age generally have less than 40% volatile matter (dry basis) [7]. Most Texas lignites have sulfur contents below 1.5% [23], although south of the Colorado River the sulfur content of the Wilcox lignite reaches 2% [7]. As a rule the Wilcox lignites north of the Colorado River contain less than 1% sulfur (as-received basis) [7]. Lignites occurring between the Brazos and Trinity Rivers may have sulfur contents in the range of 1-1.5% [7]. Sulfur is
lowest in the northeast, where lignite accumulated in ancient alluvial plains in fresh water swamps. Explanations for the higher sulfur content of the lignites of the Sabine Uplift and east central Texas include a greater degree of marine influence in the depositional environment, a slower rate of accumulation, or a deeper burial and consequent higher temperatures during coalification [24]. For lignites of Upper Eocene age, the sulfur content varies from under 1% in east Texas to 2% in south Texas [7]. On an as-received basis the average moisture content of Texas lignites is about 30% [7]. There is little regional variation in the moisture content. Several useful surveys of Texas lignites, which include extensive analytical data, are available in [7,17,20,24]. (iv) Wilcox Group lignites. The most extensive deposits of lignites, and those of greatest commercial importance, occur in the Wilcox Group. In central Texas and the northeastern Gulf Coastal Plain the Wilcox Group is divided into the Sabinetown, Calvert Bluff, Simsboro, Hooper, and Seguin Formations. The principal lignite deposits occur in the lower part of the Calvert Bluff. The Wilcox Group contains lignite interbedded with sand and clay. The Wilcox is early Eocene in age and non-marine in origin. The total thickness of the strata ranges from 183 to 457 m [25]. Lignite occurs in the upper two-thirds of the Wilcox [26], where it accumulated in hardwood swamps between alluvial ridges [27]. The commercial deposits, in seams 0.6 to 4 m thick, range from 23 to 363 Mt [26]. Generally the lignite seams are lenticular. Few seams extend over more than 26 km 2 [7]. In south Texas the seams are thinner and have more partings than the seams in east Texas. The partings consist of clay, shale, or very poor, highly mineralized grades of lignite called blackjack, bone, or rotten coal. The thicker and more extensive seams are generally more uniform and of better quality than the thinner, irregular seams. This same relationship between extent and thickness of seams and uniformity and quality of the lignite is observed for Montana lignites. The best grade of lignite, and the largest deposits, occur in the Wilcox Group north of the Colorado River [14]. The seam thickness ranges from 0.6 to 6.7 m (typically 0.9-3 m) and may be laterally continuous for up to 24 km [ 14]. North of the Trinity River the Wilcox lignite is of poorer grade and in seams which are both thinner (typically 0.6-1.2 m) and lenticular. Over the years there have probably been over a hundred mines working the Wilcox lignite [ 16]. In central Texas, Wilcox Group lignite is commercially mined at two large strip mines, one at Alcoa in Milam County and the other at the Big Brown electric generating plant in Freestone County. In this region the lignites were deposited in deltaic environments. Wilcox lignite is being mined in east Texas at Darco (Harrison County) for conversion to activated carbon. Here the Wilcox lignite is of fluvial origin. In east-central Texas, the Wilcox is divided into three formations, which are, in ascending order, the Hooper, the Simsboro, and the Calvert Bluff. Lignite is found at the top of the Hooper Formation, and at the bottom and top of the Calvert Bluff Formation. The estimated lignite in the lower and upper Calvert Bluff in east-central Texas is 5.4 Gt
10 [24], based on seams greater than 1 m thick with less than 60 m overburden. Calvert Bluff seams are typically 0.6-3 m thick with a maximum of about 6 m [24]. Some seams have been correlated for 32 km. Sixteen lignite seams are found in the Calvert Bluff [28]. The principal seams (from an economic point of view) are found in the lower Calvert Bluff within 91 m of the Simsboro Formation, and in upper 61 m of the Calvert Bluff beneath the Carrizo Sand Formation. In the lower Calvert Bluff, the thick seams tend to be both most numerous and laterally continuous in the region between the Navasota and the Colorado Rivers. An example is the commercially important Sandow deposit in Milam County. In the upper Calvert Bluff the seams are thickest and most extensive northeast of the Brazos River. The Big Brown deposit in Freestone county is an example. The important lignite deposits in Bastrop County are in the lower part of the Calvert Bluff. In the western part of Bastrop County the Hooper Formation contains numerous beds of lignite, although the beds are thin and lenticular and are unlikely to be of commercial importance. The principal lignite bed in Leon County is 2-3.3 m in thickness [7]. The upper 30--60 cm are rotten coal, lignite which is extremely friable and of otherwise poor quality. The most important of the Texas lignites occur in Milam County. The Calvert Bluff lignites in Milam County extend in a band running northeastward to the Brazos River. In some cases the seams may be up to 6 m thick, but the average thickness is 2.1 m [7]. Between the Colorado and Trinity Rivers in east-central Texas the Wilcox Group is 366 to 1067 m thick [26]. The only significant lignite in this region is in the Calvert Bluff Formation. The lignite occurs in the lower part of this formation above the Simsboro Sand. Irregular lignite occurrences are reported for the upper Calvert Bluff. The seams range in thickness from 0.6 to 7.6 m, although 1.5-3 m is typical [26]. Some are continuous for about 22 km [26]. Lignite in east-central Texas occurs between the Colorado and Trinity Rivers [24]. In this region the lignite is in the lower Calvert Bluff. The Calvert Bluff lignite occurs between belts of channel sand. In the Calvert Bluff lignites, the number of individual lignites increases and the thickness decreases in the direction of the ancient interchannel flood basins; the best lignite deposits occur at the juncture of the ancient alluvial and deltaic plains [24]. In northeast Texas near-surface lignite occurs in the upper two thirds of the Wilcox [24]. Seams in the Wilcox are less continuous than in the Calvert Bluff. This difference reflects the fact that the Wilcox lignites accumulated in smaller basins which did not remain intact over as long a time as in the deposition of the Calvert Bluff lignites. The lignite seams of greatest thickness and lateral continuity occur on the Sabine Uplift, the area of transition from the ancient alluvial to deltaic plain [24]. Simsboro lignites are found principally in sand-deficient interchannel areas [15]. Hooper lignites are most numerous and thickest in the upper portion of the formation, immediately below the Simsboro. Lignite is most common in the upper two-thirds of the Wilcox Group. The Wilcox Mount Pleasant Fluvial System occurs over a large area on the Texas-Louisiana border [29]. The lignite mined near Darco belongs to this Mount Pleasant Fluvial System. The Darco lignite is fairly
11 thick (2-3 m) and laterally extensive. The lower portion of the Darco lignite is primarily attrital lignite; a woody lignite constituting the second (and smaller) portion of the seam overlies the attrital lignite. (v) Yegua Formation lignite. Commercially, the Yegua lignite is second in importance to the Wilcox Group lignites. The Yegua lignites are not as extensive and are of poorer quality than the Wilcox lignites. Most of the important deposits of Yegua lignite occur north of the Brazos River, and tend to be concentrated in the middle and upper parts of the formation [7]. Lignite occurs in the upper part of the Y egua Formation and the lower Jackson Group in south Texas, south of the Colorado River. The deep-basin lignite occurs in a band running toward the northeast. At the northeast extremity, the lignite outcrops in central McMullen and Atascosa Counties, where it is currently being mined for the San Miguel electric power station. To the south, it occurs in strippable deposits in Zapata and Starr Counties in the Rio Grande valley. The lignites in south Texas amount to more than 180 Mt in seams of 0.6 to 4 m thickness [26]. Some of the seams extend for 22 km [26]. In Houston County the beds of Yegua lignite range from 0.6 to 1.8 m in thickness (averaging about 1.5 m) and generally occur at depths of 9-18 m [23]. These lignites are of commercial quality and have sufficient seam thickness for commercial exploitation. In south Texas lignite of a lagoonal origin is sometimes grouped as "Yegua-Jackson" lignite. The Caddell Formation (the lowest in the Jackson Group) is nominally the marker separating the Jackson and the Yegua, but in regions of south Texas the Caddell is either absent or, at best, difficult to recognize. The boundary between the Jackson and the Yegua becomes somewhat arbitrary and has to be established by paleontological evidence [ 16]. This lignite has been used commercially as drilling mud additive. (v) Jackson Group lignite. The poorest grade Texas lignite occurs in the Jackson Group [ 14]. Many of the seams are less than 1.5 m thick, though some may be laterally continuous for up to 48 km [ 14]. Most lignite beds in the Jackson Group are too local, too thin, of too poor quality, or suffer some combination of these factors, to be mined. In east Texas, the Jackson Group has been divided into four formations: the Caddell, Wellborn, Manning, and Whitsett [28]. The thickest lignite seams occur primarily in the Manning Formation. The more important lignites of the Jackson Group occur near the middle of the group and in the lower part of the Manning Formation. In Fayette County the Manning Formation lignites are notable for a very high ash value. Manning lignites have sulfur contents greater than 1.5% [ 17]. Compared to Wilcox lignite, Jackson lignites generally have higher moisture, ash, and sulfur contents, and lower calorific values [24]. Generally the older seams have the lower calorific values. The high sulfur contents and ash values are a result of the accumulation of lignite in swamps or marshes in the standplain-lagoonal regions or on the delta plain. The sulfur content also results from accumulation closer to the sea, the organic matter being affected by sulfate-rich marine waters. The high ash value reflects a greater contamination by clastics, either water-borne sediment spreading over and into the delta plain or strandplain, or airborne volcanic ash. The San
12 Miguel lignite interval contains four to six partings each 15-30 cm thick, which are believed to be of volcanic origin [24]. The best Jackson lignite occurs in east Texas. In southeast Texas, the Jackson Group lying between the Colorado and Neches rivers is about 300 m thick [26]. It consists of four formations: Caddell (at the base), Wellborn, Manning, and Whitsett. Lignite occurs in the upper Wellbom and upper Manning Formations. The Manning is the more important. Outcrops of Jackson lignites are numerous, but generally the seams are thin, usually less than 0.9 m [26]. In a 60 m section at Somerville, eighteen lignites are present, but only four are of greater thickness than 0.9 m [26]. In east Texas, lignite occurs as a continuous band in the Manning and Upper Wellborn Formations. In the Manning Formation seams are typically 0.9-2.4 m thick with a maximum of about 3.7 m. The seams are laterally continuous, commonly for 32 km and possibly up to 64 km [24]. The San Miguel lignite (lower Jackson) extends for about 40 km; the interval is typically 3-4.6 m thick [24]. Between the Colorado and Angelena rivers in east Texas, deltaic lignite occurs in the Jackson Group (upper Eocene) [24]. Lignite found in outcrops occurs in the Manning and upper Wellborn Formations [24]. The Jackson lignites have not been characterized by petrographic or palynological studies to the same extent as the Wilcox lignites, but arguments have been made for either marshy [27] or swampy [30] environments of deposition. The San Miguel lignite (upper Yegua or lower Jackson) ranges from reddish brown to brownish black in color with a dull to waxy luster [31]. Cores show no evident banding, and there is little or no hard or woody material. The Hardgrove grindability is 89 (at 28.7% moisture) and the lignite can generally be cut smoothly with a knife [31]. Pyritic sulfur averages 0.72% [31]. Seam partings range from over 60 cm in thickness down to the thickness of a knife edge [31 ]. Partings tend to be clays or carbonaceous shales. 1.2.2 Alabama (i) Occurrence. Alabama has a demonstrated reserve of lignite of 262 Mt lying under less than 76 m of overburden [32]. The inferred reserve is 1.8 Gt [32]. For the deep-basin lignites, which lie under 76-1,830 m of overburden, the demonstrated resources amount to 426 Mt, and the inferred resources, 3.4 Gt [32]. Over half the total estimated lignite resources are located in western Alabama in the Naheola Formation of the Midway Group. About 1.8 Gt occurs in nearsurface deposits of the Oak Hill lignite bed [33]. The near-surface Oak Hill lignite demonstrated resource is 925 Mt, and 4.3 Gt for the deep-basin resource [54]. The demonstrated reserves of Oak Hill lignite amount to 256 Mt, assuming an 85% recovery factor [33]. The subeconomic resources add another 205 Mt [33]. The total hypothetical resource in southwestern Alabama is 7 Gt [34]. Alabama lignites are Tertiary and late Cretaceous in age. The most important are of Eocene age (Wilcox Group). In Alabama the Wilcox is a band roughly 40 km wide running northwest to southeast across the state. This deposit includes almost the whole of Wilcox, Butler, and Crenshaw counties, and lesser portions of twelve other counties. The total demonstrated and inferred resources of Gravel Creek lignite are 386 Mt [34].
13 The oldest Gulf Coast lignites occur in the Naheola Formation (Upper Paleocene) of Alabama and Mississippi. The high sulfur contents of these lignites suggest that they may have been deposited under marine conditions [35]. The Wilcox and Claiborne Groups, which extend into Alabama from Texas, are Upper Paleocene to Lower Eocene. These lignites were deposited in a variety of environments, which ranged from fresh through brackish to saline [ 17]. Lignite is widely distributed in Paleocene and Eocene formations along the Gulf Coastal Plain in Alabama. In the Alabama-Tombigbee Rivers Region, the main lignite deposits occur in the Midway, Wilcox, and Claiborne Groups [33]. In the Midway, the lignite deposits occur in the Oak Hill Member of the Naheola Formation. The Naheola Formation is divided into the Oak Hill (lower) and Coal Bluff (upper) Members. Lignite seams ranging from 0.3 to 4.3 m thick are present near the top of the Oak Hill [33]. The Tertiary lignites run in a west-to-east band across the southern part of the state. The thickest and most persistent bed is the Oak Hill lignite. The Oak Hill Member of the Naheola Formation contains a remarkable lignite seam that can be traced for 120 km from the MississippiAlabama border in a southeastern direction to Wilcox County [18]. Over this distance the seam thickness varies from 0.3 to 4 m [18]. The inferred resources in Wilcox County are 188 Mt, underlying an area of 175 km2 [36]. Some unusual lignite deposits nearly 15 m thick have been formed in depressions created by the collapse of underground caverns. These deposits are highly lenticular (less than 1.6 km in width) and are of interest only as geological oddities. They have no evident commercial value. (ii)
Quality.
Typically the sulfur content of Alabama lignites is 1.6-6.3%, the ash value
is less than 16%, and the calorific value ranges from 9.35 to 26.1 MJ/kg (average 20.9), on a moisture-free basis [34]. An unusual aspect of the eastern Alabama lignites is a trend for increasing oxygen content with increasing depth [37]. Since it is normal to presume an increase in coalification, and hence a decrease of oxygen, with increasing depth, this finding is surprising, but appears to be real, despite the possible errors associated with calculating oxygen content by difference. A study of drill core samples has shown wide differences in sulfur contents [37], suggesting major differences in the accumulation of the precursor peats. The generally high levels of sulfur suggest a saline deposition, comparable to the environment of the Florida Everglades
(e.g. [38]) where peat is now accumulating. Analyses of some specific lignite samples have been tabulated in [20]. The Oak Hill lignite has an average calorific value of 20.9 MJ/kg (moisture-free basis), with a range of 9.35-26.0 MJ/kg [33]. Most Oak Hill lignite yields less than 16% ash; ash increases toward the pinchout in Wilcox County, and consequently the calorific value decreases in this area. Moisture ranges from 45 to 53%; sulfur, from 1.6 to 6.3% (moisture-free basis) [33]. The sulfatic sulfur amounts to 12% of the total sulfur; the balance being almost equally divided between organic and pyritic [33]. The lignite of the Coal Bluff seam is of unusually high ash. On a moisture-free basis, this lignite contains 23.1% carbon, 2.5% hydrogen, 0.6% nitrogen, 2.3% sulfur, 10.1% oxygen, and 61.4% ash [36]. The ash fusion properties are 1560 ~ initial
14 deformation, 1599" softening, and 1599" C fluid temperatures [36]. The average composition of Gravel Creek lignite is 44.05% moisture, 14.9% fixed carbon, 26.2% volatile matter, 19.79% ash, and 1.6% sulfur [34]. The average calorific value is 11.05 MJ/kg (as-received basis) and 22.4 MJ/kg (maf basis) [34]. Tuscahoma lignite (Wilcox) has an average 41% ash, 2.9% sulfur, and calorific value of 13.5 MJ/kg [33,34]. The range of calorific values of Tuscahoma lignites is 5.6 to 22.6 MJ/kg. The range of sulfur contents is 2.0-6.1%; of this, sulfatic sulfur has the uncommonly high proportion of 24.8%, while the organic sulfur is 44.6% and the pyritic, 30.6% [33]. (iii)
Midway Group. Lignite having possible commercial value occurs in the Oak Hill
Member of the Naheola Formation (middle Paleocene). The bed is generally 0.5--4 m in thickness, and represents the most extensive lignite deposit in southwestern Alabama [39]. This lignite accumulated in the interchannel areas of coastal marshes lying on a delta plain. The marshes lay behind a barrier system. The lignite itself occurs in a sequence dominated by clay. The upper portion of the Tuscahoma Sand Member (upper Paleocene) contains lignite having no commercial value. This lignite does not occur over wide areas, and the beds are generally less than 1 m thick [39]. Up to six lignite seams occur in the Tuscahoma Sand, but their combined thickness is only about 1.5 m [39]. The Oak Hill Member is 25--50 m thick. It contains fine-grained sand, sandy silts, and silty clays [40]. The lignites typically occur near the top of the Oak Hill, and are enclosed in clays. In some localities the Oak Hill seams may have been removed, wholly or in part, by erosion. The lignite is 1.2-1.5 m thick, and extends from Kemper County in eastern Mississippi to the Alabama River (Wilcox County, Alabama) [35]. Two seams of lignite occur in the upper Oak Hill Member. The upper, which is not everywhere present, is typically about 15 cm thick [33]. The interseam parting, about 1 m thick, is composed of carbonaceous sand, clay, and silt. The lower seam is 0.3 to 4.2 m thick and is the most continuous lignite seam in Alabama [33]. It extends in a belt up to 13 km wide from the Mississippi border southeasterly through Sumter, Choctaw, Marengo, and Wilcox counties. The bed finally pinches out in Wilcox County on the east side of the Alabama River, near Camden. Oak Hill lignite is enclosed in nonmarine sediments. The low ash, moderate to high sulfur, large areal extent, and tabular shape of the lignite suggest that deposition was not influenced by active streams or by the Gulf of Mexico, although a high sulfur content suggests brackish water [33]. A depositional environment having these characteristics is an inactive delta lobe. The Coal Bluff seam, in the Naheola Formation, averages 1.2 to 2.4 m in thickness [36]. In Wilcox County it averages 1.8 to 2.1 m [36]. It underlies an area of about 28 km2 between County Line and Kimbrough [36]. The measured and indicated lignite reserves in this area amount to about 66 Mt [36]. The overburden is unconsolidated sands and clays. Deep-basin lignites occur at the top of the Midway Group, in the southern portion of the Alabama-Tombigbee Rivers Region. Throughout most of the region the cover is less than 610 m thick, but in the southwestern portion of this region the Midway lignite lies beneath 910-1,200 m
15 of sediments [33]. The Midway lignites in Choctaw, Clarke, Monroe, and Washington counties comprise the most extensive and largest of the deep-basin lignites. Seam thickness can exceed 4.3 m [33]. The demonstrated reserves are 426 Mt, with inferred resources of over 3.4 Gt [33]. (iv) Wilcox Group. In Alabama the Wilcox is divided into the Nanafalia, Tuscahoma Sand, and Hatchetigbee Formations. Thin seams of lignite occur in the Nanafalia Formation, the Tuscahoma Sand, and the Hatchetigbee Formation. The principal occurrences of Wilcox lignite are in the upper (unnamed) member of the Tuscahoma Sand. This member contains six seams of fairly thin lignite. The Tuscahoma lignite occurs in a belt roughly paralleling the Oak Hill lignite, but about 27 km to the south [33]. The Tuscahoma lignite is continuous under large areas of Choctaw, Clarke, and the western portion of Wilcox counties, and in some cases may be over 1.5 m thick [33]. The demonstrated reserves of Tuscahoma lignite amount to 6.6 Mt, assuming an 85% recovery factor [33,34]. The demonstrated subeconomic resources are about 43 Mt [33]. The stacked, lenticular beds (also described as thin and tabular), high ash value, and low sulfur content all suggest deposition between distributary channels of an active delta lobe [33]. Thin seams of lignite also occur in the upper member of the Hatchetigbee Formation. The Tallahatta Formation is the lowest formation in the Claiborne Group; the Lisbon Formation overlies the Tallahatta and contains some deposits of lignite and lignitic clay. The Gosport Sand overlies the Lisbon and contains two very thin, lenticular beds of lignite. The lignites of eastern Alabama are in the Gravel Creek Sand Member of the Lower Nanafalia Formation (Wilcox Group). These lignites are younger than those of western Alabama. In contrast to the western Alabama lignite which is laterally extensive, the eastern Alabama lignite tends to occur in "pods" which may be fairly thick but are of limited areal extent [35]. The seams are enclosed by silty or micaceous sands. These lignite pods may have arisen from peat deposition in abandoned stream channels [41]. Deep-basin lignites also occur in the Wilcox Group. However, they appear to be less extensive than the Midway deep-basin lignites, as well as somewhat thinner (rarely exceeding 1.5 m) [33]. The deposits are thin and lenticular. 1.2.3 Arkansas (i) History. Arkansas lignites have been used as sources of montan wax, dyes, and heating oils, as well as fuel for local domestic heating. The lignite makes an acceptable domestic and industrial fuel when dehydrated and shaped into briquettes. Early attempts to use the lignite as a fuel for blacksmith forges were unsuccessful [42]. (ii) Occurrence. Lignites occur in the southwest and northeast corners of Arkansas and in the south-central region, in an area of about 15,900 km2 [43]. The major deposit lies in a 8-32 km wide belt running from Little Rock to the Texas border [25]. The total lignite to a depth of 45 m is estimated to be 12.2 Gt [18], irrespective of seam thickness. In some cases, lignite deposits exceeding 1 m of thickness are encountered at depths of less than 45 m [1]. Most seams are less than 2 m thick and are lenticular. In addition, the seams may be broken up by faults or ancient
16 channels. The total resources of Wilcox lignite in Arkansas are 3.9 Gt [34]. Pulaski County has the largest reserves, with approximately 40% of the estimated total. Other counties containing large deposits, expressed as a percentage of the total state reserves, are Saline, 20%; Ouachita, 16%; and Dallas, 15%. The most extensive lignite area in Arkansas is about 155 km2, northwest of Camden in Ouachita County [44]. The lignite is exposed along the banks of the Ouachita River and its tributaries. The average seam thickness is about 75-90 cm, with a maximum of 1.8 m [44]. The deposit contains about 68 Mt [44]. A single deposit of an extent of about 24 hectares, but containing a lignite seam 2.5 m thick, occurs near Manning in Dallas County [44]. This lignite was used to manufacture brown pigment. Lignite near Sweet Home in Pulaski County has a maximum thickness of 8 m [44]. Arkansas lignites are found in the Wilcox, Claiborne, and Jackson Groups (Tertiary). Most of the lignite occurs in the Wilcox Formation (Eocene) in the Gulf Coastal Plain. The lignite is present in Cleveland, Dallas, Grant, Hot Spring, Ouachita, Pulaski, and Saline counties. Many of the beds are thin and lenticular, with no real commercial value. Over 85% of the strippable reserves are in the Wilcox Group, which contains about 19.6 Mt [8]. The Crowley's Ridge area contains lignite of the Wilcox Group in Clay, Craighead, Greene, and Poinsett counties. The most abundant lignite and the thickest seams generally occur in the Wilcox Group. The average thickness of Wilcox Group strata in this region is about 275 m. Lignite occurs in the Wilcox in beds up to 4 m thick within 45 m of the surface [34]. The thickest seams exceed 7 m. The beds are generally lenticular. The most important beds in the group occur in the lower and middle Wilcox. These lignites were deposited in a fluvial environment. The lignite has been most extensively studied in Pulaski and Saline counties. The Claiborne Group overlies the Wilcox. Claiborne lignites occur in lenticular beds of limited extent, with maximum thickness of 3 m [34]. The estimated resources are 4.3 Gt [34]. The lignites originated as attrital deposits in deltaic and shallow marine environments [34]. Some lignite occurs in the Tokio Formation [42]. (iii)
Quality. The
calorific value of Arkansas lignite is about 14 MJ/kg [44]. The lignites are
high in ash, and therefore have low calorific values on an as-received basis. The sulfur content of Wilcox Group lignites is less than 1% [8]. The calorific value ranges from 6.44 to 17.6 MJ/kg [8]. The lignites of the Wilcox Group average 35.7% moisture, 17.6% ash, 0.57% sulfur, and 13.4 MJ/kg calorific value on an as-received basis [34]. On a moist, mineral-matter-free basis the Wilcox lignites average 16.5 MJ/kg, corresponding to an ASTM rank of lignite A [34]. These lignites contain 64-90% translucent attritus [25]. The average composition of Claiborne lignites, on an as-received basis, is 38.7% moisture, 17.9% ash, 0.62% sulfur, with a calorific value of 12.7 MJ/kg [34]. The ASTM rank is lignite A, based on a moist, mineral-matter-free calorific value of 15.7 M.l/kg. 1.2.4 Louisiana (i) History. A lignite bed about 1.5 m thick is exposed on the east bank of the Sabine River
17 [45]. The first attempt at mining this lignite occurred in the 1870's, but the barge transporting the lignite downriver to market sank, and the attempt was apparently never repeated. The lignite was considered to be a marketable fuel only in the local area, where it was in competition with pine wood. A 5.5 m thick bed of lignite is exposed at Iron Mine Run on Avery Island [46]. An attempt to exploit the lignite for local fuel use never came to fruition. (ii) Occurrence. The lignite in Louisiana is early Tertiary in age. Outcrops occur north of a line running from Natchitoches to Sabinetown and from the Red to the Sabine River. Underground deposits occur between the Red and the Ouachita rivers, along a line from Natchitoches to Catahoula Parish. The area of the state underlain by lignite is estimated to be 23,000 kin2 [20]. The resources likely to be of commercial significance are located in the Sabine Uplift area in the northwestern portion of the state [47], and are of the same age as the Wilcox lignites of Texas [18]. The estimated lignite resources are 1.5 Gt, but, because of the limited amount of data available for some areas, the actual total may be higher by as much as 450 Mt [18]. Most of the seams are less than 2.5 m thick [ 18]; many are less than 1.5 m thick [8], and tend to be lenticular. The Chemard Lake Lentil (DeSoto Parish) is continuous for a distance of 24 km. This single deposit may contain over 450 Mt. It is about 3 m thick and contains lignites and lignitic clays [48]. The Lentil marks the contact of the Naborton and Dolet Hills Formations, and is also sometimes known as the Blue Bed. A second bed of lignite, sometimes called the Red Bed, lies 8-15 m below the Chemard Lake Lentil. The two beds are separated by shales, clays, siltstones, and sandstones. The Green Bed is about 34 m below the Chemard Lake Lentil. The Green Bed has a maximum thickness of 1.5 m [48]. The Sabine Uplift is centered in De Soto Parish and extends from there into Louisiana and Texas. Lignite occurs principally in the Wilcox Group (Eocene); it is found to a lesser extent in the overlying Claiborne and Jackson Groups. The principal lignite bed is the Chemard Lake, which occurs at the top of the Naborton Formation of the Wilcox Group. The Naborton Formation includes lignitic silts, as well as clays and calcareous sands [48]. Chemard Lake lignite occurs over a fairly wide area of Louisiana. It is laterally extensive for over 80 km [49]. The lignite thickness ranges from 2.4 m to less than 30 cm; the overburden averages about 23 m [47]. The estimated reserves of Chemard Lake lignite amount to 495 Mr, based on an assumption of 1.8 m average seam thickness and specific gravity of 1.29 [47]. Chemard Lake lignite has a woody structure, low sulfur content, moderate calorific value, and high ash value, characteristics which suggest deposition from a fresh water environment. In Sabine Parish an area of about 40 km2 is underlain with lignite having an average seam thickness of 1 m [47]. The reserves are estimated to be 45 Mt [47]. Lignite outcrops at the surface in nearly all the formations of the Wilcox and Claiborne groups in Sabine Parish. However, the only ones which seem to have commercial potential are the Bayou San Miguel and the Sabine River Stone Coal Bluff beds [45]. The Bayou San Miguel bed is typically 1 m thick; the lignite is hard and black with little woody structure [50]. The Sabine River - Stone Coal Bluff lignite seam is of comparable thickness. Other lignite deposits of potential commercial value occur in the Beinville,
18 Bossier, Caddo, Natchitoches, and Red River parishes. The Porters Creek Formation is the topmost formation in the Midway Group. It consists of lignitic shales as well as calcareous shales and clays [48]. The Porters Creek Formation directly underlies the Naborton Formation in the Wilcox Group. (iii) Quality. Chemard Lake lignite has a low sulfur content (0.53%) and a calorific value of 14.7 MJ/kg [49]. The average maceral content is 60.8% vitrinite, 26.3% exinite, and 12.9% inertinite [49]. This lignite consists of bright, banded, and banded-bright lithotypes deriving mainly from forest-moor paleoflora which accumulated on an upper deltaic plain. The presence of duller lithotypes correlates with increased pyrite content. Sunrise lignite (also called the Green Seam or Green Bed) lies about 30 m below the Chemard Lake lignite. The sulfur and calorific values of the Sunrise lignite are slightly higher than the Chemard Lake lignite, 0.62% and 16 MJ/kg, respectively [49]. Lignites from De Soto and Sabine parishes have an average calorific value of 16.6 MJ/kg, with 0.63% sulfur, 16.1% ash, and 30% moisture [47]. Analyses of lignite and ash samples have been tabulated in [20]. 1.2.5 Mississippi (i) Occurrence. Lignite in Mississippi is found mainly in the area north of a line through Meridian, Jackson, and Vicksburg and to the east of the "bluff." In Mississippi the so-called bluff is actually a line of bluffs paralleling the Mississippi River and running on the east side of the river from Kentucky to Louisiana. The seams tend to be lenticular and generally less than 1.5 m thick [8]. Lignites outcrop in an area starting at the border with Tennessee in the north, curving through the central part of Mississippi, and then extending to the border with Alabama in the east [51]. Lignite occurrences cover 32,600 km2 in the state, with outcrops in 33 of the 82 counties [34]. The lignite beds are generally tabular and discontinuous. Mississippi lignite reserves are found in the Wilcox, Claiborne and Midway Groups. The total estimated resource is estimated to be 4.5 Gt [ 18], predominantly in the Wilcox, and is of Eocene age. The principal lignite beds occur in the Ackerman Member of the Wilcox Group. The Wilcox lignites are of principal significance in east-central Mississippi, in a belt running from Calhoun through Lauderdale counties. The best deposits lie in Webster, Calhoun, and Lafayette counties. Other counties containing appreciable deposits are Yalobusha, Choctaw, and Jasper. Lignites of commercial potential in the Wilcox were deposited in fluvial or delta-plain environments. These lignites are irregular in shape, erratic in thickness, and of limited extent [ 1]. The shapes vary from narrow deposits typical of meandering, fluvial systems to elliptical deposits of deltaic origin. At the outer edges, the seams may be only a few centimeters thick, but at the center of the deposit the seams may be up to 3.7 m thick [1]. Generally the Claiborne lignites are similar to those of the Wilcox Group. The Claiborne lignites are found mainly in the Cockfield (Yegua) Formation. Lignite is abundant in this formation. Seams up to 1.5 m thick have been observed [51]. Some sands in the
19
Cockfield are lignitic, and some lignitic clays are also observed. Some lignites are also found in the Cook Mountain, Kosciusko, and Zilpha Formations. The depositional environment for the Claiborne lignites was similar to that for the Wilcox lignites. (ii) Quality. The moisture content of Mississippi lignite is in the range of 40-45%, and may exceed 50% [34]. The sulfur content runs up to 4%, but is generally less than 2% [34]. On a moisture-free basis the calorific value is in the range of 16 to 26 MJ/kg [34]. A summary of analyses of some Mississippi lignite samples has been compiled in [20]. The Wilcox lignites average about 16% ash and less than 1% sulfur [51]. The sulfur content increases geographically as lignite is sampled more and more closely to the ancient marine environment of Kemper and Lauderdale counties. The moisture is in the range of 40--45%; the calorific value, 11-13 MJ/kg (as-received basis) [51]. The Claiborne lignites are generally high in ash and low in calorific value. 1.2.6 Tennessee Lignite is found in western Tennessee in the Wilcox and Claiborne Groups. The total resource is estimated to be 900 Mt [18]. The seam thickness is generally less than 2.7 m [18]. 1.3 THE F O R T UNION REGION
1.3.1 North Dakota (i) History. The first use of North Dakota lignite as a fuel was made by the members of the Lewis and Clark expedition, which wintered in North Dakota in 1804 [52,53]. These explorers reported on the abundant deposits of lignite observed along the Missouri River when they passed through the area in 1805. Extensive exploration of the lignite deposits, particularly in the Missouri Valley, was conducted by the Hayden expedition in 1854 [54]. The lignite-bearing strata were referred to as the Great Lignite Group [55]. Hayden's chief colleague, F. B. Meek, substituted the name Fort Union for Great Lignite [56]. The name Fort Union was taken from a United States army fort on the banks of the Missouri River near the Montana-North Dakota border [55], although the fort was in fact in Montana. The first commercial mining was carried out by the Northern Pacific Railroad in 1884, across the Little Missouri River from Medora [52]. All North Dakota lignite is currently recovered by strip mining. The production was 3 Mt in 1950 and then gradually declined to 2.1 Mt by 1958; however, the production increased again through the 1960's and reached 4.1 Mt in 1968 [8]. (ii) Occurrence. The largest reserves of lignite in the United States occur in western North Dakota and adjacent areas of eastern Montana and northwestern South Dakota. The age of the lignite ranges from late Cretaceous through Eocene [57]. Lignite occurs in the Hell Creek Formation (Upper Cretaceous), the Fort Union Group (Paleocene), and the Golden Valley Formation (Eocene). The lignite deposits of North Dakota generally lie west of the 100th meridian. The lignite field can be divided into three provinces, based on the overburden characteristics [58].
20 North of the Missouri River the overburden is primarily glacial drift. Between the Missouri River and the limit of glaciation, the overburden is mainly fine-grained clastic sediments with some scattered areas of glacial drift. In the unglaciated area (the southwestern region of the state) the overburden is clastic rocks. The overburden on most of the lignite in North Dakota contains higher quantities of sodium than does that on the subbituminous coals further to the west in Montana and Wyoming [58]. The high sodium content has consequences for possible sodium toxicity problems during mined land reclamation, and may also represent the source of sodium in the lignite, which is related to ash deposition problems during combustion in power plant boilers (Chapter 11). More than one hundred lignite beds have been described in western North Dakota, but because few have been traced laterally for more than 40 km, it is possible that many of these hundred beds may be at the same, or nearly the same, horizon as others [59]. Exposures of lignite beds are particularly good southwest of the Missouri River, since overlying glacial deposits are fairly thin and discontinuous. In contrast, northeast of the Missouri the exposures of lignitebearing series are very poor because of a widespread cover of glacial deposits, which in some places are 60 m thick [59]. Good exposures of the lignite beds are observed in bluffs along stream valleys. An excellent example is the Little Missouri River in Slope, Billings, and Golden Valley counties, where the relief in places reaches 300 m, exposing the entire section of lignite-beating rocks [59]. A total of 22 lignite beds has been noted in these counties; the thickness of individual beds ranges from 1 to 11 m, and the aggregate thickness of all the beds is 58 m [59]. The lignite deposits of North Dakota cover an area of about 83,000 km2, of which about 72,000 km2 are underlain by beds over 1.4 m thick [58,60]. However, only about 2800 km2 contain lignite recoverable by surface mining [58]. The demonstrated strippable reserve base of lignite in North Dakota is 11.8 Gt [3], based on the criteria of a minimum seam thickness of 1.5 m, a maximum overburden of 30 m, and a maximum stripping ratio of 10:1 [ 1]. (The economic limits for a reserve to be considered strippable are a minimum seam thickness of 1.5 m, 15 m of overburden, maximum stripping depth of 67 m, and minimum calorific value of 14 MJ/kg [8]). The total estimated resources amount to 318 Gt [58,60-62] (other sources have estimated 544 Gt [59]). In addition, there are an estimated 163 Gt of lignite in the category of hypothetical resources
(i.e., resources in unexplored and unmapped areas) [58,60,62]. Of the total identified resource, 89.3% is subeconomic, a category which includes the inferred resources and any indicated or measured resources in seams less than 1.5 m thick [58]. The remainder (10.7%) represents demonstrated, measured, or indicated resources in seams 1.5 m or greater in thickness [58]. Approximately 14 Gt lie within 30 m of the surface [58]. If a 90% recovery factor is allowed for strip mining, the recoverable reserve is 13.1 Gt [58]. Future improvements in mining technology, to increase the depth at which strip mining is economically feasible and to increase the recovery factor, will bring more of the total resource into the category of recoverable reserves. The largest amounts of recoverable reserves, in units of megatonnes, occur in the following counties: Slope, 1825; Dunn, 1633; Mercer, 1621; Stark, 1041; and Williams, 923 [58]. The remainder is distributed among eighteen other counties.
71 Resource estimates come mainly from outcrop information. Lignite present at some distance from the exposure might not be included in the estimate. In some areas only the most prominent bed is included in the estimate, neglecting lignite in other beds. Furthermore, only lignite in beds at least 75 cm thick is included in the estimate. Thus the actual amount of lignite in the ground is likely to be somewhat greater than the estimated amount. Lignite recoverable by strip mining has been estimated to be 17 Gt [61]. A useful summary, with measured, indicated, and inferred resources divided by seam thickness (0.75-1.5, 1.5-3, and >3 m) for each county has been published [62]. Reserves recoverable by strip mining are summarized in Table 1.11 [3]. TABLE 1.11 North Dakota lignite reserves recoverable by strip mining [3]. Area Reserves Mt Adams County 91 Beach- Wibaux 454 Beaver Creek 136 Beulah-Zap 816 Bowman 1,089 Center 635 Dickinson 1,633 Dunn Center 1,633 Falkirk- Washburn 1,089 Gascoyne- Scranton 272 Grant County 272 Hazen 726 Hettinger County 181 Niobe 272 Noonan - Columbus 136 Renners Cove 907 Stanton 272 Stony Creek 635 Velva 544 Wilton 45 Total .................. 11,838
The oldest lignite-bearing unit is the Hell Creek Formation, consisting mainly of about 150 m of nonmarine sandstones, siltstones, and mudstones [58]. Lignites in the Hell Creek are generally too thin for successful commercial mining, discontinuous, and of poor quality. The Hell Creek is the youngest of the Cretaceous formations, and contacts the Ludlow, the oldest of the Tertiary formations. The top of the Hell Creek was recognized as the base of the Paleocene sediments [63]. Some lignite also occurs in the Lance Formation (Cretaceous), which underlies the Fort Union. The Lance Formation outcrops in a belt running southwestward from central North Dakota to northwestern South Dakota; the belt of outcrops is roughly 80 km [59]. The Fort Union Group contains essentially all of the lignite included in the estimated North
22 Dakota resources. The Fort Union Group is included in the rocks of the Zuni Sequence (Cenozoic). The Fort Union Group derived from erosion of the Laramide Rocky Mountains [64]. Both the lignites and the elastic sediments in the Fort Union are predominantly derived from terrestrial origins [65], except for the Cannonball Formation in the lower part of the Fort Union. (The Cannonball is a marine deposit, while the other formations are non-marine fluvial, alluvial, or swampy origin.) Lignites occur in the Ludlow, Slope, Bullion Creek, and Sentinel Butte Formations [1], all but the Cannonball. Most of the lignite recoverable by strip mining is in the Bullion Creek and Sentinel Butte Formations [28]. The reserves and resources of the lignite in the Fort Union have been estimated at, respectively, 18 Gt and 318 Gt [66]. The vertical range of beds in the Fort Union is about 400 m [20]. In North Dakota the eastern border of the Fort Union runs southeastward from Renville County on the northern boundary roughly to the center of the state. In mid-state the border begins running southwesterly to Adams County on the southern boundary. South and east from Bismarck the Fort Union is thin, and in many places entirely missing. Some of the lignite beds extend over 3,900 km2, with thicknesses ranging from 1.5 to 12 m [93]. However, the lignites vary considerably in thickness, down to a few millimeters [68]. Lignite seams comprise less than 5% of the total thickness of these formations, the majority of the thickness being interbedded silt and clay and silty fine- to medium-grained sand [73]. Most of the strippable lignite deposits are found in the Williston Basin, the largest occurring on the southwestern flank of the Basin, and smaller deposits on the eastern flank. Here the bed thickness ranges widely, from less than 25 mm to over 7.6 m [8]. In some cases two or more beds of thickness appropriate for commercial mining may occur in the same area. Most of the mineable lignite is under less than 300 m of overburden, and 70% is under less than 150 m [60]. There is very little structural variation in the lignite in the Fort Union. The beds are generally flat, with an estimated dip of only 4 m/km [69]. Both the Cannonball and Ludlow Formations are about 90 m thick [67]. The Ludlow contains lignites that range in thickness from less than 30 cm to about 7 m [1], with aggregate thickness up to 12 m [62,70]. The Ludlow is best exposed in southwestern North Dakota, especially in Bowman County. The Ludlow underlies the Cannonball in the western portions of North Dakota. The Ludlow Formation is the lowermost of the Fort Union Group, and is similar to the underlying Hell Creek Formation. The Slope Formation contains strata that had previously been assigned to the upper Ludlow or to the Tongue River. Lignite makes up about 10% of the rocks in the Slope Formation, and occurs in beds having a maximum thickness of 4 m [1]. Like the Slope Formation, the Bullion Creek has recently been defined and contains many strata formerly assigned to the Tongue River Formation. The Bullion Creek is also similar to the Slope Formation in that lignite beds comprise about 10% of the strata [1]. The lignites average about 1 m in thickness, with a maximum bed thickness of 4 m [1]. The Harmon and Hansen beds are the lowest lignite members of the Bullion Creek Formation. The Harmon bed underlies small areas in themnorthern part of Bowman County. It reaches a maximum thickness of 10 m [60].
23 Overburden is 36 m or less [3]. At the Gascoyne mine (Bowman County) two seams are separated by about 90 cm of partings. The Gascoyne mine supplies lignite for use in a power plant in Big Stone City, South Dakota. The Weller Slough bed is also in the Bullion Creek Formation. It is about 3.7 m thick in Mercer County [71 ]. The Coal Lake Coulee bed generally ranges from 60 to 120 cm thick, with a maximum of 2.4 m [71]. The Tavis Creek bed, a relatively thin (ca. 90cm) bed, lies just below the contact between the Bullion Creek and Sentinel Butte Formations. Lignite beds in the Sentinel Butte range in thickness from less than 30 cm to, in some instances, over 6 m [ 1]. Sentinel Butte lignites are less continuous than those of the Bullion Creek. Sentinel Butte sediments tend to be darker, relative to the Bullion Creek, and are described as "somber" [58]. Generally, lignite seams occurring in the Sentinel Butte are lenticular and often split into multiples. The Sentinel Butte Formation is primarily silt, clay, and lignite, with sands at both base and top. The Hagel bed is the lowest lignite bed in the Sentinel Butte [71]. The average thickness in Dunn County is about 2.4 m, although in some locations the Hagel bed splits into several minor seams separated by inter-seam partings up to about 1 m thick [71]. The Hagel bed dates to the late Paleocene. It is extensive throughout the central and south-central portions of Oliver County along Square Butte Creek and its various tributaries [72]. The Hagel bed occurs throughout the Knife River drainage basin and into adjacent McClean and Oliver counties [71,73]. Currently the Hagel bed is mined at the Center mine near Center (Oliver County), the Glenharold mine near Stanton (Mercer County), and the Falkirk mine near Falkirk (McClean County). At the Center mine the seam is about 3.4 m thick under 15 m of overburden [3]. Here the Hagel seam contains partings of dark carbonaceous clay or gray clays. The underclay is a graygreen clay with some fragments of lignite; the overburden is gray and consists mainly of clayey silts and silty clays [74]. This lignite is burned at the Square Butte power plant. The BaukolNoonan mine supplies lignite for an adjacent power plant. The seam thickness ranges from 3 to 4.3 m [75]. The Keuther seam, about 11-12 m above the Hagel in this location [58,75], is mined if local conditions permit; however, much of the seam has been removed by erosion or has oxidized to leonardite. Baukol-Noonan lignite is generally of low sodium content. This characteristic is related to the permeable overburden containing abundant carbonate minerals; sodium in groundwater could be replaced by calcium through ion exchange. The overburden is mainly glacial till and poorly consolidated sandstones and shale. At the Glenharold mine the seam thickness ranges from 60 cm to 2.4 m, under 12 m of overburden [3]. The overburden is primarily soft sandstone, shale, and clay with a veneer of glacial drift. However, a layer of a hard, well cemented sandstone is immediately above the Stanton lignite. This lignite is also used as fuel for an electric power plant. The Falkirk mine operates in two seams, one of 90 cm and the other of 2.4 m thickness, separated by a 1.5 m parting [3]. The overburden thickness is 24 m [3]. The lignite is used as fuel in a power plant in nearby Underwood. The Kinneman Creek bed is one of the most persistent lignites throughout the Knife River Basin. The main seam is about 2.4 m thick [71]. Associated seams about half as thick lie within 2.4 to 12 m of the main seam. Lignites along the Little Missouri River northward from the vicinity of Yule are sometimes
24 referred to as the Great Bend group of beds [76]. Of these, Bed I (also called the Sand Creek bed) is the thickest bed (about 11 m) that outcrops anywhere in North Dakota. This outcrop was located about 8 km southwest of the town of Amidon [76]. The Sand Creek bed can be traced for over 64 km, from the old Yule Post Office at the mouth of Williams Creek nearly to the Harmon ranch, 13 km south of Medora. The Antelope Creek bed usually occurs as two seams separated by a clay parting, but in some locations may consist of several seams separated by clay, sand, or silt. The sequence of multiple seams with interbedded sand, silt, or clay may be up to 15 m [71]. It is generally traceable throughout the Knife River Basin. The Jim Creek bed is a thin seam generally less than 1 m thick which occasionally splits into two [71]. The Spaer bed has a maximum thickness of about 1.8 m in the vicinity of Beulah and Zap and generally is of 60 cm to 1.8 m thickness in that region [71]. Elsewhere in the Knife River Basin it is thinner and even pinches out in places. In some locations it separates into four very thin beds separated by silt, sand, or clay. In Billings County the D and E seams range up to 4 m in thickness [3]. This lignite is notable in being the first commercial discovery of uraniferous lignite in the United States, the discovery occurring in the vicinity of Rocky Ridge in Billings County. Mining of lignite for its uranium content was carried out in 1956-8 and again in 1966-7 [3]. Northeast of Dickinson, the D and E seams are 2.7 to 5.5 m thick, under a maximum of 30 m of overburden. The Beulah-Zap deposit in Mercer and Oliver counties is comprised of three separate lignite fields: North Beulah, South Beulah, and Zap. In the North Beulah and Zap fields lignite is found in the Zap bed. In the South Beulah field the lignite is in the Schoolhouse bed. Both beds are part of the Sentinel Butte Formation. At the Indian Head mine the Zap bed is typically 3-3.7 m thick [58]. The maximum thickness is 5.2 m [28]. The overburden is mainly composed of clay and sandstone, and averages 23 m in thickness [58]. The Beulah-Zap bed averages about 3.6 m in thickness; however, it frequently splits into as many as five seams with clay, silt, or sand partings and in such cases the thickness of the entire interval may be as much as 9 m [71]. North of Beulah the Beulah-Zap merges with the Spaer to form a single seam about 6 m thick [71]; in western Dunn County the Beulah-Zap merges with the Schoolhouse bed. The Beulah-Zap bed underlies a large area of Mercer County. In places it reaches a maximum thickness of 6.7 m [60]. The Beulah-Zap also occurs in southeastern Dunn County, where it crops out along both sides of the Little Missouri River. The maximum thickness of the Beulah-Zap in Dunn County is 4.3 m [60]. In the Renner's Cove area the Beulah-Zap is 5.5 m thick, with overburden ranging from 15-30 m [3]. Currently active mining occurs at the Indian Head and Beulah mines. The latter enjoys a thicker seam, 4.9 overburden, 15
vs.
vs.
2.7 m on average, and less
20 m. At the Indian Head mine the Beulah-Zap seam has an average thickness
of about 4.3 m [75]. The Freedom mine was established to supply lignite to the Antelope Valley power station and the adjacent coal gasification plant near Beulah. The seam thickness here is 4.9 m, with maximum overburden of 30 m [3]. An extension of the Zap bed, running northward from
25 the Zap lignite field, is found south of Lake Sakakawea in Mercer County. The average thickness here is 5.5 m, with up to 30 m of overburden [58]. The Zap bed also makes up the Hazen deposit in Mercer County. The average thickness of the bed is about 3.7 m, but is often split by a shale parting [58]. The overburden is mainly sandstone and clay with a thin cap of glacial till. The Dakota Star mine was operated in this deposit until 1966. The Schoolhouse bed in the South Beulah field consists of three seams which average 3.7, 3.4, and 1.4 m in thickness [58]. The overburden thickness is an average 19 m and is primarily clay and sandstone [58]. The Schoolhouse bed splits into two seams separated by 2.4-3.7 m of clay, sand, and silt; the two seams themselves may be in the range of 1.5 m in thickness [71]. The Twin Buttes bed is of highly variable quality, ranging from a fairly thick single seam of good quality lignite to a thin seam of a carbonaceous clay. In some locations it consists of a single, 1.5 m thick seam while in others it occurs as two seams of this thickness separated by clay up to 1.2 m thick [71]. The Dunn Center deposit in Dunn County ranges from 3.4 to 7.3 m thick with less than 15 m of shale overburden [58]. The Stanton bed forms the Washburn deposit in McLean County. The average thickness of the Stanton bed is 2.4 m, with an average overburden thickness of 15 m [58]. The overburden is mainly clays, sands, and sandy clays with a thin veneer of glacial drift. The Stanton bed also comprises the Stanton deposit in Mercer and Oliver counties. In Burke County the Bonus seam is about 2.6 m thick, and overlies a 1.8 m thick Niobe seam. The overburden covering the Bonus seam is 46 m or less [3]. In the Noonan-Columbus area, the Noonan seam is 2-3 m thick [3]. Lignite is actively mined at the Baukol-Noonan or Larsen mine, where the seam is 2.4 m feet thick with a maximum overburden thickness of 15 m [3]. In the Dickinson area a small amount of lignite is mined from the Lehigh seam at the Husky No. 2 mine. This lignite is used for the production of charcoal briquettes. The seam is about 3 m thick, under 27 m of overburden [3]. Lignite is mined from the Coteau seam in Ward County at the Velva mine. Seam thickness at the mine is about 3.7 m [3]. The maximum overburden thickness in Ward County is 30 m, with the lignite ranging from 3 to 4.6 m thick [3]. The Coteau bed was named because of its proximity to the rough, hilly moraine belt known as the Missouri Coteau [76]. The Harnisch bed is the uppermost lignite in the Sentinel Butte. It occurs just below the contact with the Golden Valley Formation. It is typically 1.2 m thick. In Dunn County the bed separates into a series of seams separated by clay; the entire interval may be up to 5.5 m thick [71]. The Golden Valley Formation (Eocene) lies above the Fort Union. The Golden Valley contains thin beds of lignite, but the amount is insignificant, and the lignite has little commercial potential [67]. The principal members are a kaolinitic claystone interbedded with sandstone and a micaceous sandstone/siltstone. The former is capped with a thin layer of lignite which seldom exceeds 1.8 m in thickness [58]. The Golden Valley is also included in the Zuni Sequence, which terminated following deposition of the Golden Valley. fiii)
Quality.
North Dakota lignite is mainly brown, though in some deposits it appears
26 black and lustrous. Many samples are conspicuously woody in appearance, often exhibiting the grain or cells of the wood. Breakage along the grain occurs readily, but less easily in other directions. Sometimes flattened trunks or branches are found in the lignite. The extent of the "woodiness" varies with location in the seam, with some portions of the seam consisting of alternating layers of a tough, brown lignite and a black, lustrous, brittle material. Weathered surfaces are generally black, with a bright, vitreous luster. The luster of the weathered surfaces seems inversely related to the ash value; as the yield of ash increases, the luster of the weathered surface is duller. The high moisture content, which may exceed 40% in some locations, makes freshly mined pieces sometimes feel moist. The lignite normally cleaves parallel to the bedding plane but seldom cleaves vertically. Consequently the lignite can sometimes be mined in thick slabs often more than 1 m long. The lignite degrades rapidly on exposure to the air (a process called slacking or slackening). Storage of the lignite occasionally leads to spontaneous combustion. The beds are sometimes marked by clinkers where the lignite has bumed from natural causes (the characteristic color of this material leads to the term "red dog"). Severely weathered exposures of lignite contain a soft, earthy, medium-brown material known as leonardite. Extensive compilations of analyses of North Dakota lignites have been published [20,58,7779]. Moisture and ash values are the most variable. For 413 samples, the average moisture content was 37.5%, with a standard deviation of 2.3 and range of 28.1-45.1% [79]. The average ash value was 6.4% on an as-received basis, with standard deviation of 1.9 [79]. The ash value increases in a westerly direction. Calorific values are virtually constant, 28 MJ/kg on an maf basis [79]. The average sulfur content was 1.1% (maf basis), with a range of 0.3-4.5% [79]. The average CaO content of the ash 31% [79]. The average Na20 content is 6.5%, but the standard deviation is 5.0 and the range is a remarkable 0.1-27.0%. SiO2 is highly variable and averages 27% [79]. Both A1203 and Fe203 show little variability; they average 14% and 12%, respectively [79]. Structural deformation in the Fort Union has been very slight except in the extreme southwestern part of North Dakota (the Badlands) and in the Black Hills region of western South Dakota. Consequently there is little variation in rank throughout the Fort Union, particularly in North Dakota. In eastern Montana the coals of the Fort Union become subbituminous in rank, but the change is so gradual with westward distance that there is no apparent change in North Dakota. In fact, the variation of lignite composition and properties from one horizon to another is about the same magnitude as the variation within a single lignite bed. North Dakota lignites show large within-mine variability of most components. An extreme case is the Gascoyne mine (Harmon Bed, Bullion Creek Formation), for which the following ranges are reported [79]: moisture, 32.444.8%; ash, 5.0-14.3%; SiO 2, 18.0-61.6%; A1203, I0.1-16.2%; Fe203, 2.8-15.1%; CaO, 14.7-44.7%; and Na20, 1.1-10.2%. The average quality of Gascoyne lignite, on an as-received basis, is a calorific value of 14.4 MJ/kg, with a proximate analysis of 40% moisture, 25% volatile matter, 26% fixed carbon, and 6% ash [3]. The average as-received sulfur content is 0.75% [3].
27 The quality of lignite from the Center mine (Hagel bed, Sentinel Butte Formation), on an asreceived basis, is calorific value 15.3-16.4 MJ/kg, 6--7% ash, 0.6-0.9% sulfur, 35% moisture, 29% volatile matter, and 29% fixed carbon [3,58]. The lignite is black to brownish black and slacks rapidly when exposed to air [74]. Lignite from the Glenharold mine in this seam is slightly better with regard to calorific value, ash, and sulfur, being, on an as-received basis, 16-16.5 M.l/kg calorific value; 38% moisture, 26-27% volatile matter, 30-31% fixed carbon, and 4-5% ash; and 0.4-0.5% sulfur [3,58]. From the Falkirk mine, also operating in the Hagel seam, the average quality is 14.9 MJ/kg calorific value; proximate analysis of 39% moisture, 29% volatile matter, 28% fixed carbon, and 7% ash; and a sulfur content of 0.6% (as-received basis). Typically the lignite of the Dunn Center deposit of the Sentinel Butte is 38-39% moisture, 27% volatile matter, 27% fixed carbon, 7-8% ash, 0.8-1% sulfur with a calorific value of 14.6 MJ/kg, on an as-received basis [58]. The average quality of lignite from the Leigh seam, used commercially for the manufacture of briquettes, is, on an as-received basis, 15.1 MJ/kg calorific value; 35% moisture, 25% volatile matter, 32% fixed carbon, and 7% ash; and 1.2% sulfur. The average qualities of lignites from the Dakota Star, Indian Head, and Beulah mines (Beulah-Zap bed) are quite similar. On an as-received basis the calorific value is 16-16.5 MJ/kg. The proximate analysis is 35-37% moisture, 26-29% volatile matter, 28-31% fixed carbon, 6 8% ash, and a sulfur content ranging from 0.6% at the Indian Head mine to 0.8% at Beulah [3,58]. Indian Head lignite is characterized by abundant, thick vitrain. Coalified tree stumps near the top of the seam have been observed, ranging in diameter from 15 to 75 cm [75]. Indian Head lignite is high in sodium, containing typically 8.5% Na20 in the ash [75]. The overburden is a highly impermeable clay low in carbonate minerals, the reverse of the situation for the low-sodium Hagel seam at the Baukol-Noonan mine. The composition of lignite from the Zap bed south of Lake Sakakawea, on an as-received basis, is 34% moisture, 30% volatile matter, 30% fixed carbon, 6% ash, 0.5% sulfur with a calorific value of 16.4 MJ/kg [58]. Velva lignite, mined from the Coteau seam, on an as-received basis, averages 15.8 M,l/kg calorific value; 37% moisture, 27% volatile matter, 31% fixed carbon, and 5% ash; with 0.2% sulfur [3]. It is remarkable for a very high calcium content, sometimes exceeding 40% reported as calcium oxide in the ash. The lignite in the Coteau bed is black and less woody in appearance than most of the lignite elsewhere in North Dakota. The lignite is intermediate in appearance between a cannel coal and the brown lignite typical of much of the North Dakota lignite [76]. It readily splits along the bedding plane, and tends to slack when exposed to sun and air movement, or other storage conditions that allow the moisture to evaporate. The lignites in the Fort Union Group frequently serve as aquifers. (In fact, any rock with 35% moisture arguably is an aquifer [58].) The yield of water is generally 4 to 40 L/min [58]. The chemical quality of the water from the lignite aquifers varies greatly in hardness, being extremely hard in some cases, and frequently shows a reddish-brown coloration due to dissolved or suspended organic materials. The water is used for both for domestic purposes and for watering livestock. Groundwater flowing into the pits can be a problem in many of the lignite mines in the
28 region. Bedrock aquifers consist mainly of consolidated sandstones and limestones with some interbedding of shales, siltstones, or claystones. However, some of the sands and clays are associated with lignites. Both the Fort Union and Hell Creek Formations contain major lignite beds that are aquifers. 1.3.2 Montana (i) Occurrence. About 200 Gt of mineable coal are available in Montana, and, of this, about three-fourths is lignite or subbituminous in rank. The lignite reserves of Montana are estimated to be 79 Gt [80,81], generally found in the northeastern part of the state. The area underlain by lignite exceeds 18,000 km2 [20]. Many of the strippable coal beds are up to 12 m thick. Six continuous lignite beds are present in northeastern Montana; four are fairly thick [82,83]. The seams range from a few cm to over 6 m in thickness [20], but tend to be in the range of 4 to 6 m, with a maximum of about 26 m [8]. The vertical range of lignite seams exceeds 450 m [20]. The Fort Union Formation contains over 90% of the coal reserves of Montana [81]. The formation derives its name from Old Fort Union, which was located near the confluence of the Missouri and Yellowstone Rivers [84]. In Montana the Fort Union Formation has been divided into three members, which are, from oldest to youngest, the Tullock, Lebo, and Tongue River Members [85]. The three members are of Paleocene age. The base of the Tullock was defined to be the first persistent bed of lignite above the Cretaceous dinosaur-bearing beds [63]. The contact with the Lebo Member is taken to be the base of the Big Dirty lignite seam [85]. The Lebo shale member is distinguished from the Tongue River on the basis of lithologic differences [81]. Near the North Dakota border the rocks occurring at the same stratigraphic position as the Lebo are known as the Ludlow Formation. The coals of the Tongue River Member are lignite or subbituminous in rank. In the eastern part of the state the Tongue River is 335 m thick [81]. Some lignites of Tertiary age occur in former lake beds which are now basins lying between mountain ranges in the southwestern portion of the state [81]. Strippable deposits of lignite occur in the eastern part of the state, in the Tongue River Member. The demonstrated reserve of strippable lignite in Montana is 14.3 Gt, based on the criteria of a minimum seam thickness of 1.5 m, a maximum overburden of 38 m, and a maximum stripping ratio of 8:1 [1]. The lignites occur in the Tongue River member are found in the Powder River and Williston Basins, which respectively contain 8.8 and 6.4 Gt of reserves recoverable by strip mining [3]. The reserves in the Powder River Basin are shown in Table 1.12 [3]. The Tongue River contains most of the economically important coal deposits of eastern Montana, with total strippable reserves of all ranks estimated to be 25 Gt [81,85]. The Knobloch Bed contains the largest strippable reserves in the Tongue River, 6.8 Gt [85]. Here the lignite seams may be up to 12 m in thickness, and much of the lignite is within 30 m of the surface [3]. A summary of the reserves recoverable by strip mining is given in Table 1.13 [3].
29 TABLE 1.12 Powder River Basin lignite reserves recoverable by strip mining [3]. Area Reserves, Mt Ashland 1633 Beaver-Liscom Creek 272 Broadus 590 Cache Creek 18 Diamond Butte 227 East Moorhead 318 Fire Creek - Pinto Creek 136 Foster Creek 984 Goodspeed Butte 272 Pumpkin Creek 1452 Sand Creek 168 Sonnette 454 Threemile Butte 91 West Moorhead 1361 Yager Butte 816 Total ..................................... 8792
TABLE 1.13 Williston Basin reserves recoverable by strip mining [3].
Area Reserves, Mt Beach- Wibaux 544 Breezy Flat 272 Burns Creek 1360 Coalridge 72 Ekalaka 18 Fort Kipp 113 Four Buttes 45 Fox Lake 136 Glendive 726 Hardscrabble Creek 181 Knowlton 454 Lame Jones - Milk Creeks 91 Lanark 45 Lane 181 Little Beaver Creek 82 Little Sheep Mountain 109 North Fork- Thirteenmile Creeks 544 O'Brien - Alkali Creeks 318 Pine Hills 45 Poplar River 45 Redwater Creek 454 Reserve 27 Smith - D r y - Parsons Creeks 91 Weldon - Timber Creeks 318 Wolf Creek 136 Total .................................... 6407
30 Cii) Quality. The coals of Montana show a progressive increase in rank westward from the border with North Dakota. Generally the lowest rank occurs along the North Dakota border and the highest, along the Wyoming border. In easternmost Montana the coal is lignite; near Miles City it is subbituminous; west of Miles City it becomes subbituminous C in rank; and reaches bituminous rank near Red Lodge. The coal in the Fort Union Formation in eastern Montana ranges in calorific value from 16.3 to 20.9 MJ/kg on an as-received basis [86]. With the westward increase in rank is a concomitant decrease in moisture content. Montana lignites generally have as-mined moisture contents in excess of 35%, with about 30% fixed carbon and 25-30% volatile matter [79]. Lignite in eastern Montana contains up to 43% moisture [81]. The ratio of fixed carbon to volatile matter averages 1.18 [79]. Ash values are typically in the range of 5-14%; and sulfur, 0.5-1.0%, although sulfur contents up to 1.7% have been reported [79,81]. On an maf basis the sulfur content averages 1.0% [79]. The average as-received calorific value is 15.8 MJ/kg [79]. The heating values show a tendency to increase from east to west. In the ash the CaO content averages 27%; MgO, 10%. The SiO2 content averaged 31%; A1203, 20%; and Fe203, 8% [79]. The iron content of the ash is very variable. Lignites formed in lake bed deposits of Tertiary age are much higher in ash value, about 20%, but of comparable sulfur content, relative to the Fort Union lignites [81]. As a rule, beds of thickness greater than 1.5 m have lower ash and are more uniform in quality than the smaller beds [87]. However, the quality is highly variable laterally; some lignite seams up to 4.6 m thick which are low ash may become high in ash value in a lateral distance of a few hundred meters to a kilometer [87]. The lateral variability originates from unstable conditions of deposition in the bogs or marshes where the original organic matter was accumulating. Lignites from Richland County show subconchoidal fractures and a brown streak [87]. Transverse to the bedding plane, a fresh surface usually shows compact, alternating layers of dull and shiny material. The woody texture of the lignite is preserved, with only a moderate flattening of the cells. On exposure to air, the lignite loses moisture, and the surface luster dulls; small cracks appear, which gradually become deeper and more numerous until the sample slacks to a powder. Fresh samples of lignite from the Knobloch bed show a bright luster, attributed to previtrain, a material derived from the coalification of single, relatively large fragments of ancient plants. Lignite occurs along Coal Creek near the North Fork of the Flathead River in Flathead County, as well as along the Middle and South Forks of the Flathead River [88]. Only the deposit along the North Fork of the fiver was actively worked. The lignite from the Coal Creek region contains nodules of mineral resin [89]. Tables of analyses of Montana lignites have been published [20,79,90] including data on ash composition [79]. A compilation of analyses of samples of the major deposits in seven Tongue River coal beds has been published [85]. (iii) Powder River Basin lignites. In the Moorhead area the Anderson, Dietz, and Canyon beds have commercial potential [91]. Dietz coal generally ranks as subbituminous C [91], but is classified as lignite in the regions of Decker and West Moorhead. In the Decker area the Dietz
31 seams combine with the Anderson to produce a multiple seam up to 24 m in thickness [3]. The lignite contains about 5% ash and 0.35% sulfur and has a calorific value of 17.9 MJ/kg, on an asreceived basis [3]. The quality is very similar in the West Moorhead region, where the seam thickness is about 5 m [3]. The West Moorhead coal is classified at the exact upper limit of lignite, having a calorific value of 19.3 MJ/kg on a moist, mineral-matter-free basis [3]. The Canyon, one of the most widespread beds in Montana, is not commercially mined. Much of the coal is classified as subbituminous C, but some lignite and some subbituminous B coals have been reported [91]. Lignite occurs near Diamond Butte and Threemile Butte. At Diamond Butte, the average seam thickness is 3.5 m [3]. On an as-received basis, the lignite quality is 4 - 5 % ash, 0.3-0.4% sulfur, and 17-17.4 MJ/kg calorific value [3]. In the Threemile Butte area, the seam has an average thickness of 2.6 m and the lignite is of lower quality: 6.2% ash, 0.9% sulfur, and 15.8 MJ/kg (as-received basis) [3]. Of the Tongue River coals in Montana, the Canyon bed shows both the greatest ash value and the greatest variation in ash value. The maximum thickness of the Knobloch bed is 20 m in the Otter Creek and Ashland deposits. The Knobloch is not currently mined. The rank varies from lignite to subbituminous. Lignite is found in the Foster and Sand Creeks areas. The Sand Creek lignite has a calorific value of 17 MJ/kg, with 6.5% ash and 0.3% sulfur [3]; Foster Creek, a calorific value of 17.7 MJ/kg with 7.5% ash and 0.9% sulfur [3]. At Foster Creek the seam is about 3.4 m thick [3]. The magnitude of the Foster Creek deposit is illustrated by the estimate that sufficient reserves exist to fuel thirty 200 MW electric generating stations (i.e., 6000 MW total) for forty years [92]. In the Beaver Creek-Liscom Creek area, the Knobloch is about 4.6 m thick; the lignite is about 9% ash and 1% sulfur [3]. The coal in the Knobloch bed reaches a thickness of 14 m on Otter Creek; the rank ranges from lignite to subbituminous C [86]. The Otter Creek deposit is low in ash and sulfur. Characteristics of the Knobloch coals are summarized in Table 1.14 [90]. TABLE 1.14 Characteristics of Knobloch bed coals [90]. Coal deposit Ashland Beaver - Liscom Creeks Foster Creek Otter Creek Poker Jim O'Dell Creeks Sand Creek
Cal. value, MJ/kg 17.8-21.1 17.1-19.6 17.2-18.2 18.6-21.2 19.5--21.2 16.8-17.3
Sulfur,% 0.1-0.5 0.2-0.9 0.3-1.6 0.1-0.4 0.1-0.6 0.3
Ash, % 3.7--6.8 5.1-13.8 6,7-8.7 3.0-10.6 3.7-6.4 5.1-8.3
The Roland seam represents the top of the Tongue River Member of the Fort Union Formation. The rank ranges from lignite in the Squirrel Creek area to subbituminous in the Roland area. The seam thickness ranges from 1.8 to 4.3 m [3]. In general the coal in the Roland deposit ranges in calorific value from 16.3 to 21.2 MJ/kg, with sulfur content of 0.2-0.7% and ash value
32 of 3.8--9.7% [90]. In the Squirrel Creek deposit the calorific value ranges from 15.4 to 19.3 MJ/kg; sulfur, 0.2-0.6%; and ash, 3.0-14.2% [90]. The Roland bed is about 60 m above the Smith bed [91]. The Cook bed lies below the Canyon and above the Wall beds. The bed occurs in Powder River County in the regions around Goodspeed Butte, Sonnette, and Yager Butte. The seam occurs as two benches. In all three areas the calorific value is 15.6-15.8 MJ/kg and the ash content is 10-12% on an as-received basis [3]. In the Yager Butte deposit the benches are 12-23 m apart, and thicknesses are 0-5.8 m for the upper bench and 2-3.4 m for the lower [90]. The as-received sulfur content is 0.5% [3]. The Goodspeed Butte lignite benches average 5 and 4 m, but the sulfur content is 1.5% [3]. The benches lie 10-14 m apart [90]. At Sonette the bench thicknesses and the sulfur content are intermediate between these extremes. Here the benches are 6.6 to 12 m apart [90]. Characteristics of the Cook Bed coals are shown in Table 1.15 [90]. TABLE 1.15 Characteristics of Cook bed coals [90]. Coal deposit Goodspeed Butte Sonnette Yager Butte
Cal. value, M.l/kg 15.5-16.0 15.2-16.7 13.7-17.9
Sulfur,% 1.2-2.1 0.7-1.9 0.3-0.7
Ash,% 8.9-12.4 6.5-13.3 3.8-20.7
The Elk bed is also in the Yager Butte area. It is about 4.6 m thick [3], with a range of 3 to 6.4 m [90]. Lignite quality, on an as-received basis, is 17.4 MJ/kg calorific value, 5.5% ash, and 0.35% sulfur [3]. The Dunning bed lies below the Elk. The average thickness of the Dunning is 5 m [3], with a range of 4.3-6 m [90]. On an as-received basis, the calorific value is 17.9 MJ/kg; ash, 5%; and sulfur, 0.3% [3]. The Sawyer bed occurs in Powder River County around Ashland and Pumpkin and Little Pumpkin Creeks. The thickness reaches 11 m [90]. Sulfur content is low, 0.4-4).6%. In the Ashland area the ash is 5% and the calorific value is 18.1 MJ/kg; the ash value is higher near Pumpkin Creek, 8.5%, and thus the calorific value is somewhat lower, 17 MJ/kg [3]. In Powder River County the Broadus bed ranges up to 7.6 m thick [3,90]. The maximum thickness is 8 m at the Peerless mine [86]. The calorific value is 17.2 MJ/kg; ash, 7%; and sulfur, 0.3% [3]. The reserve estimated to be recoverable by strip mining is 590 Mt [3]. The Broadus bed lies 30 m above the base of the Tongue River [90]. The coal in the Flowers-Goodale seam varies in rank. In the Foster Creek area the rank is lignite, with a calorific value of 17.7 MJ/kg, 8% ash and 0.5% sulfur [3]. The seam thickness in the Foster Creek area ranges from 60 cm to 4.3 m [92]. In the Beaver Creek-Liscom Creek area the Terret seam is about 2.4 m thick; the average quality is 16 MJ/kg, 9% ash, and 1.1% sulfur, on an as-received basis [3]. In the Foster Creek area the coal is at the border of classification between lignite A and subbituminous C, with a moist, mineral-matter-free calorific value of 19.4 MJ/kg. This coal has a 6% ash value and a remarkably
33 low sulfur content of 0.2% [3]. Here the seam is about 2.7 m thick [3,92]. In the East Moorhead area the T seam ranges in thickness to 7.6 m; the lignite quality is 6% ash, 0.6% sulfur, and 16.5 MJ/kg on an as-received basis [3]. At East Moorhead the ash ranges up to 13.2% and the sulfur to 1.2% [90]. The T bed lies about 80 m above the Broadus [90]. The Pawnee bed is about 6 m thick in the regions of Cache Creek and Pumpkin Creek near Sonnette [86,90]. The Pawnee forms two benches which may be up to 14 m apart [79]. Characteristics of the coal in the Sonnette field are 12.9-18.4 MJ/kg calorific value, 0.2-2.7% sulfur, and 3.925.3% ash [90]. In the Fire Gulch deposit, the calorific value is 17.8 MJ/kg with 0.2% sulfur and 6.0% ash [3]. The Brewster-Arnold bed lies 72-84 m below the Wall bed [90]. The maximum thickness is 6 m [90]. In the Birney field the characteristics of the Brewster-Arnold coal are 18.6-21.9 MJ/kg calorific value, 0 . 2 - 0 . 7 % sulfur, and 3.1-8.2% ash [90]. (iv) Williston Basin lignites. The Dominy bed contains two or three benches, the lower averaging 6 m and the upper 2 m in thickness [90]. In the Knowlton deposit the coal quality is 14.6-15.9 MJ/kg calorific value, 0.2-0.9% sulfur, and 3.8-10.5% ash [3,90]. Comparable values for the Pine Hills deposit are 16.9-17.2 M.l/kg, 0.4-0.6% sulfur, and 6.6-8.1% ash [3,90]. In the Knowlton area the bed occurs as three benches, the upper being 8 m; the middle, 4 m; and the bottom, 3 m. In the Pine Hills area the lower bench is 6 m thick [3]. In the Poplar River area these seams are 2.5 to 3 m thick. The calorific value is low, 13.7 MJ/kg on an as-received basis, with 9% ash and 0.5% sulfur. In the Beach-Wibaux area, the C seam ranges to 9 m in thickness, with 36 m or less of overburden. The maximum thickness is 12 m, at the Black Diamond mine [3]. In some places the overburden is less than 18 m thick. The lignite quality, on an as-received basis, is 14 MJ/kg calorific value, 8% ash, and 0.9% sulfur [3]. In the Four Buttes area, the seam is much thinner, only about 3 m on average. The lignite quality is much the same, being about 14.2 MJ/kg calorific value, 10% ash, and 1.1% sulfur on an asreceived basis [3]. In the Burns Creek area the Pust seam ranges up to 6 m in thickness, with less than 60 m of overburden [3]. The lignite quality is 14.2 MJ/kg calorific value, 8% ash, and 0.65% sulfur [3]. In the North Fork-Thirteenmile Creek area, the seam is 8 m thick, and the quality has improved. Here the average calorific value is 16 M.l/kg, with 7% ash and 0.5% sulfur [3]. Seam thickness is 3.4 m in the Fox Lake area, with 15.8 MJ/kg calorific value, 6% ash, and 0.5% sulfur. In the Redwater Creek area the S seam can reach 6 m in thickness, usually under less than 46 m of overburden [3]. On an as-received basis the lignite has a calorific value of 15.8 MJ/kg, with 11% ash and 0.4% sulfur [3]. In the Weldon-Timber Creek area, the seam thickness is only 3.6 m, but the quality has improved to 17.4 MJ/kg calorific value, 6% ash, and 0.3% sulfur [3]. In the Breezy Flat area, lignite is mined commercially at the Savage mine, the output supplying a power plant at Sidney. At the Savage mine the seam thickness is about 6 m. The calorific value on an as-received basis is 15.1 MJ/kg. The proximate analysis averages 38% moisture, 27% volatile matter, 27% fixed carbon, and 7% ash. The sulfur content is 0.5% [3]. In the Hardscrabble Creek area the F and H seams range from 2 to 3 m in thickness, with
34 overburden less than 60 m [3]. On an as-received basis the lignites have a calorific value of 15.1 MJ/kg, ash of 7% and sulfur content of 0.6% [3]. The Fort Kipp and Peck seams are each about 1.5 m thick, separated by a parting of about 6 m. In the Fort Kipp area the average calorific value is 15.8 MJ/kg on an as-received basis, with 5% ash and 0.3% sulfur. In the Reserve area the Timber Coulee seam is about 3 m thick. Quality is 15.8 MJ/kg calorific value, 7% ash, and 1% sulfur on an as-received basis [3]. The Smith bed lies about 34-46 m above the Anderson bed [91]. The Smith is generally thin, but is remarkable for the large number of petrified tree stumps it contains. Many of the stumps remain in an uptight position. Two samples of the Smith bed lignite from the Decker deposit have calorific values of 17.7 and 19.2 MJ/kg, sulfur 0.6 and 1.0%, and ash 6.8 and 30.2% [90]. Silica was a major constituent of the ash, amounting to 38.5 and 78.3% of the ash. 1.3.3 Saskatchewan Lignite provides about a third of Canada's recoverable coal reserves on a weight basis, and about a fourth when the amount of coal is expressed on a calorific value basis [93]. The province of Saskatchewan contains the major Canadian lignite deposits, which are of Tertiary age. The resources amount to 3.8 Gt, of which 1.36 Gt are measured and the remaining 2.43 Gt are indicated [94]. The total recoverable reserves of Saskatchewan lignite are estimated to be 2.1-2.4 Gt, all extractable by surface mining [93,95]. On an as-mined basis, the Saskatchewan lignites tend to fall in the range of 20-32% moisture, 15-25% volatile matter, and 13-35% ash [94]. Sulfur contents are low, in the range of 0.3-0.8% (daf basis). The calorific value ranges from 12-15.4 MJ/kg. Some of the properties of lignites from the major areas in Saskatchewan are summarized in Table 1.16 [94]. TABLE 1.16 Quality of Saskatchewan lignites [94].
Area Cypress Estevan Willow Bunch Wood Mountain
Proximate Analysis Moisture,% Vol. Mat.,% 20-28 22-45 27-32 22-25 25-32 20-25 24-28 15-23
Ash,% 15-23 13-25 14-30 22-35
Calorific val. MJ/kg, moist 8.8--13.7 13.0-15.4 12.1-15.1 10.7-13.7
The sulfur content of the lignites from all four areas lies in the range 0.2-0.6% [94]. Data on the quality of lignites in Saskatchewan is available in [96]. Lignite occurs principally in four basins: Cypress, Estevan, Willow Bunch, and Wood Mountain; these deposits are collectively known as the Ravenscrag Formation. A small deposit, in seams too thin for profitable mining (i.e., less than about 1.5 m), occurs in the area of Wapawekka near Lac La Ronge. Not only are the seams thin, but this lignite is very high ash.
35 Seams in the Ravenscrag Formation range from 1 to 3 m; generally the lignite is shallow and level [95]. Lignite of the Ravenscrag Formation is mined in a 2.5 m seam in the Klimax Mine of the Butte River Coal Company near Estevan [97]. The Ravenscrag Formation is equivalent in age (Paleocene) to the Fort Union lignites in the United States. At Estevan there are eight lignite seams in a stratigraphic interval of 230 m [97]. Of these, the four upper seams amount collectively to 8 m of lignite, and occur in an interval of 38 m [97]. The annual production of Saskatchewan lignite is about 10 Mt [95], used almost entirely for electric power generation. Most is burned in minemouth plants, but about 1 Mt per year is exported to Ontario. The lignite in Saskatchewan is a major contributor to the electric power production in that province. In 1982 the Saskatchewan Power Corporation consumed 71% of the lignite produced in the province [98]. Saskatchewan Power operates the Souris Valley and Poplar River mines. Other mines which provide lignite to Saskatchewan Power are the Utility and Costello mines (Manalta Coal Ltd.) and the Boundary and Bienfait mines (Luscar Ltd.). The Saskatchewan lignite deposit extends into the southwestern portion of Manitoba, but in Manitoba the seams are so thin as to not be currently considered for mining. 1.3.4 South Dakota (i) History. The total recorded lignite production in South Dakota is only 1.23 Mt, through January 1, 1964 [ 103]. Production peaked in 1941, when 63.5 kt of lignite were mined [79,103]. Most of the production has come from strip mines in Dewey and Corson counties. Virtually all the lignite mined in South Dakota for fuel use was used for domestic heating. During the settlement of the Dakotas, the lignite deposits in the southeastern quarter of South Dakota were of considerable local interest, because of the great distances to other supplies of fuel. The only gun battle ever reported in the lignite literature is said to have occurred as a result of a dispute over a lignite seam in Big Sioux Valley [ 104]. The lignites of South Dakota have been of some commercial interest due to their uranium content. During active mining in 1955-8 and again in 1962--6, 320 t of uranium were recovered from lignites of the Slim Buttes and Cave Hills areas of Harding County. At one time, the most important lignite mining area of South Dakota was the Isabel-Firesteel district in Dewey and Ziebach counties. The lignite in this district is neither as thick nor as extensive as other deposits in the state, but commercial activity was greatly facilitated by the availability of a railroad line which allowed the lignite to be transported and marketed away from the immediate area of mining [3]. (ii) Occurrence. Lignite occurs in a rectangular area in the northwestern part of the state, primarily in Perkins and Harding counties. Lignite having commercial potential occurs in Harding, Dewey, Perkins, and Corson counties, and the northern portion of Meade County; small portions of five other counties may contain lignite. The lignites are an extension of the larger deposits in North Dakota. They occur in the Lance and Fort Union Formations (Tertiary). Bed thickness is typically 1.2 to 1.8 m [8]. The Fort Union Formation does not extend very far into South Dakota, and little lignite is found among the Fort Union sediments in this state. The predominant lignite
36 beds occur in the Lance Formation, particularly in the Ludlow and Hell Creek members [18]. The lignite-bearing area of South Dakota is at the southern edge of the Fort Union region, near the edges of the areas in which these lignites were deposited. Thus the beds tend to be thinner and more lenticular than the lignite deposits of North Dakota and Montana. The oldest lignite-bearing formation is the Fox Hills. The Fox Hills Formation is the first shore deposit of the Cretaceous sea as it began its retreat. The Stoneville lignite-bearing member lies in the upper third of the Fox Hills [ 104]. The Hell Creek Member (late Cretaceous) of the Lance Formation overlies the Fox Hills. The Hell Creek underlies most of the northwestern quarter of the state [103]. It contains much of the South Dakota lignite. The lignite outcrops form a semicircle in Corson, Dewey, Harding, and Perkins counties. The Hell Creek lignite generally occurs in thin, lenticular beds less than 300 m in diameter and 60-100 cm thick [105], and in fact it is better known as a good source of dinosaur fossils than as a lignite source. Some of the Hell Creek lignite occurs in beds of 1.2 to 1.8 m in thickness [ 104]. The lignite beds generally occur 12-24 m above the base of the formation. Seams thick enough to support commercial mining are found in the Isabel-Firesteel area, Dewey and Ziebach counties; Gopher, Corson County; and the Slim Buttes area of Harding and Perkins counties. Mining has also occurred in northern Meade County. The Fort Union Formation comprises, in ascending order, the Ludlow, Cannonball, and Tongue River Members. The Cannonball Member is a marine unit and does not contain lignite; however, the Ludlow and Tongue River Members are non-marine and are lignite-beating. The Ludlow is the most prolific lignite-bearing unit in South Dakota [106]. The Tongue River is present only in the northern parts of Harding and Perkins Counties. Although the seams range up to 2.7 m in thickness [103], the total amount of lignite in this member in South Dakota is small because of its limited areal extent. The Ludlow Member of the Fort Union Formation overlies the Hell Creek. In South Dakota the Ludlow contains the greatest amount of lignite. In Harding County the Ludlow may be up to 107 m thick. The Ludlow is thought to be equivalent to the Lebo Shale and the Tullock Member of the Fort Union in Montana [106]. The beds containing the largest reserves of South Dakota lignite are the Widow Clark and the Giannonatti, both of which occur in the Ludlow member of the Fort Union in Harding County [ 106]. The abundant lignite seams in Harding County occur in terrestrial and shore-line deposits of sand and sandy shales. These lignite are the most persistent and thickest in South Dakota, with a maximum thickness of 4.3 m [ 104]. The two beds make up the Cave Hills field. The Giannonatti is the thickest bed in South Dakota, having a maximum thickness of 4.2 m [ 106], but it tends to thin rapidly. The Giannonatti seam has an average thickness of 1.8 m and a maximum of 4 m [3]. The maximum overburden thickness is 37 m [3]. The lignite in the Slim Buttes area averages about 1 m in thickness [3]. The youngest lignite is in the Tongue River Member of the Fort Union. The Tongue River overlies the Ludlow. Despite the importance of the Tongue River as a source of lignite in North
37 Dakota, Montana, and Wyoming, it contains little lignite in South Dakota. In Perkins County the thickest bed is the Lodgepole, one of several beds of lignite in the Tongue River Member, which ranges from 1.5 to 2.7 m thick [3,106]. The lignite reserves of South Dakota are estimated to be 1.8 Gt [80,106]. The area of the state underlain by known lignite deposits is 20,000 km2 [103,106]. About 84% of the reserves are found in Harding County; most of the rest in Perkins County (about 9%) and Dewey County (about 6%). Very small amounts of lignite are found in Corson, Meade, and Ziebach counties. The demonstrated strippable reserve base in South Dakota is 360 Mt, based on the criteria of a minimum seam thickness of 1.5 m, a maximum overburden of 30 m, and a maximum stripping ratio of 12:1 [1]. The major reserves recoverable by strip mining are shown in Table 1.17 [3]. TABLE 1.17 Reserves of South Dakota lignite recoverable by strip mining [3]. Area Reserves, Mt Cave Hills 159 Isabel - Firesteel 91 Lodgepole 27 Slim Buttes 23 Total .............................. 300
The total resources have been estimated at 2.7 Gt [8]. Over 900 Mt of lignite are estimated to occur in seams more than 86 cm thick [107]. This estimate does not take into account the entire lignitebearing region of South Dakota [ 104]. Based on the original known resources estimate of 1.8 Gt [106], 63% occurs in seams of 0.8-1.5 m thickness and only 3% in seams greater than 3 m [103]. The Stoneville area is underlain by at least 45 Mt of lignite [108]. However, only 1.1 Mt occurs in deposits thick enough, and accessible enough, for mining [104]. Perkins and Harding counties contain 995 kt of mineable lignite, excluding the Hell Creek and Fox Hills lignites [ 107]. In the southeastern quarter of South Dakota some lignite seams 5-10 cm in thickness are exposed in the Dakota Formation of Big Sioux Valley and in the Niobrara Formation near Springfield [ 104]. Some lignite has been encountered by water well drillers at depths of 18-30 m from the surface [104]. These occurrences have been reported near Stickney, Aurora County; Geddes, Charles Mix County; and Fulton, Hanson County. These lignites occur in or near the top of the Dakota Sandstone and the base of the sand in the Graneros Formation. (iii)
Quality.
The lignite beds range from a few cm to over 5 m in thickness [20]. In
general, the seams in South Dakota are not as thick as lignites of the same strata in Montana and North Dakota. Most of the lignite is close to the surface, with overburden thickness typically in the range of 1.8 to 6 m [20]. The lignite beds are generally flat-lying in regions of little to moderate topographic relief. The average calorific value of the lignites in the Lance and Fort Union Formations is 14-16.3 MJ/kg and the average sulfur content is less than 1% [8,104]. On an as-
38 received basis, the Fort Union lignite is 34.3% moisture, 29.1% volatile matter, 29.5% fixed carbon, and 7.1% ash [ 104]. Proximate analyses of some South Dakota lignite samples have been tabulated in [20]. The average analyses of Ludlow lignites are shown in Table 1.18 [ 104]. TABLE 1.18 Average analyses of lignite from Ludlow member, Lance Formation, South Dakota [ 104].
Proximate, % Moisture Volatile Matter Fixed Carbon Ash Ultimate, % Carbon Hydrogen Nitrogen Sulfur Oxygen Calorific Value, MJ/kg
As-received
Moisture-and-ash-free
37.92 28.43 26.25 10.55
-49.59 50.41 --
3 5.01 6.33 0.50 1.25 45.20 13.4
68.68 4.16 0.99 2.58 23.25 25.7
The average quality of the lignite in the Cave Hills field, on an as-received basis, is a calorific value of 13.5 MJ/kg; proximate analysis of 41% moisture, 24% volatile matter, 26% fixed carbon, and 9% ash; with 0.9% sulfur and 0.1% U308 [3]. Average as-received quality of lignite in the Lxxtgepole seam is 16.3 MJ/kg calorific value, 11% ash, and 0.75% sulfur [3]. The Firesteel seam is 1 to 2 m in thickness [3]. Average as-received quality is 16.3 MJ/kg calorific value, 6% ash, and 0.5% sulfur [3]. The Hell Creek Formation lignite is close to subbituminous in rank. It has been classified as lignite by virtue of the high moisture content, which is sufficient to cause slacking on air drying, and a brown streak test [ 105]. Distinct horizontal laminations are observed in the Hell Creek lignite exposed on the Standing Rock and Cheyenne River Reservations. These laminations are a result of alternation of a dull, dark brown lignite which constitutes most of the seam with a bright, black socalled glance coal occurring in laminae or lenses of about 2.5 cm in thickness. The Stoneville lignite, and the Hell Creek lignite found near Isabel, contain unusual amounts of transparent pale lemon-yellow, brittle, irregularly shaped resin bodies. These resin bodies range from the size of specks to about 6 mm in diameter [105], with reports of some up to 12 mm across [104]. The average as-mined analysis of the Hell Creek lignite is 36.8% moisture, 26.6% volatile matter, 7.1% ash, and 29.4% fixed carbon [104]. The maximum moisture content is about 42% [104]. The average sulfur content, on an as-received basis, is 0.52% [ 104]. The calorific value averages 15.7 MJ/kg on an as-received basis, and 24.9 MJ/kg air-dried [104]. The lignite quality in the Slim Buttes area averages, on an as-received basis, 14.9 MJ/kg
39 calorific value, 7% ash, and 2% sulfur [3]. The ultimate analysis of lignite from the Phillips mine, near Strool, is 72.6% carbon, 4.84% hydrogen, 1.28% nitrogen, 2.39% sulfur, and 18.9% oxygen, on a moisture-and-ash-free basis [104]. The calorific value, on the same basis, is 28.5 MJ/kg. As a rule, the Fox Hills lignites are the thinnest of any of the South Dakota lignites. The seam thickness ranges from a few centimeters up to 1.4 meters, although over most of the area the average is less than 60 cm [ 104]. 1.4 O T H E R L I G N I T E S OF T H E UNITED STATES
1.4.1 California (i) History. The discovery of lignite in California dates from the placer mining of the gold rush days. The first discoveries were in the areas of Big Bar, Cox Bar, and along Hayfork Creek. The existence of the Big Bar deposit on the Trinity River was first noticed in 1896 [109]. For many years the lignite was used locally as a fuel in blacksmith forges in the mining camps. A lignite interbedded with fine-grained sandstone and shale was mined near Big Bar from 1929 to 1934 and was used locally as a fuel [110]. The lignite of the Carmel Mine (Monterey County) was discovered in 1874 [111]. Some of the lignite was shipped to San Francisco for use as a fuel. In 1879 a railroad was constructed to transport the lignite from the mine to the coast (a distance of about 8 km) for loading onto ships [112]. Nevertheless, mining ceased the next year, and then continued in an on-again, off-again manner, apparently subject to various law suits. The total production through 1893 amounted to only 18 kt [113]. By 1925 the mine had been idle for many years [114]. Lignite reserves recoverable by strip mining in Amador County in the region of lone were used a century ago in the locality as a domestic fuel. Occasional use of the lignite in this way continued sporadically until about the time of World War II. Since the late 1940's, the lignite has been mined as a source of montan wax, rather than as a fuel. A lignite seam 1.4 m thick was uncovered by the gold mining operations of the Wiltshire mine, which was a hydraulic mine. Some of this lignite was recovered in 1926 by driving adits into the seam and was used locally as a fuel for blacksmith forges [115]. By 1929 some of the lignite was being transported to Redding and Eureka for use as domestic fuel, but the mine closed long before the onset of World War II [ 116]. The Reese deposit (Trinity County) was mined commercially in 1936-38, the lignite being used locally and transported to Redding. In 1949 the feasibility of using the Reese lignite for the manufacture of barbecue briquettes was investigated, but commercial production was never begun. (ii) Occurrence. The area of the state underlain by lignite is estimated to be 1,300 km 2, with a total of about 900 Mt of lignite [20]. The most extensive deposit of lignite occurs in Amador County. The lignite occurs in the Ione Formation (Eocene) [3]; lignite beds range from a few cm to 9 m in thickness [25]. Only one mine is currently in operation in the area of Ione. The lignite beds
40 and associated clay and sand strata comprise the Ione Formation. The lignites are lenticular and discontinuous. They are believed to have formed in manner similar to the Gulf Coast lignites [ 117]. Interest in these lignites stems from the fact that they are commercial sources of waxes. Small lignite deposits occur near Covelo (Mendocino County), 220 km north of San Francisco, and near Hayfork and Douglas City in Trinity County. The Covelo lignite is Eocene, and the others are probably Pliocene coals [ 118]. Lignite of Eocene or Oligocene age is found in Hayfork Valley and Hyampom Valley, at Poison Camp, and near Redding Creek. The commercial development of these lignites has suffered because of the distance to markets, as well as competition from other fuels and hydroelectric power. (iii)
Quality.
On an as-received basis, the lignite of the Ione Formation is 42% moisture,
32% volatile matter, 14% fixed carbon, and 11% ash, with 1 to 1.3% sulfur and a calorific value ranging from 13 to 14.2 MJ/kg [3]. A discussion of California lignite on a county-by-county basis has been published, with a tabulation of a few analyses [20]. The Ione lignites occur in an Eocene sequence which is mainly sandstone [118]. The lignites have very high in liptinite content, derived from spores, cuticles, resins, and waxes. Much of the liptinite consists of a fine, broken detritus. Cutinite occurs in both thin and massive bands. Blebs of cuticular wax and dispersed microspores can be observed. Resin occurs both in isolated, oval-shaped bodies and in vesiculated rodlets. Although there is a distinct microscopic structure parallel to the contacts, the Ione lignite does not contain massive amounts of woody lignite nor fine attritus, both of which are characteristic of other lignite deposits. Layers of huminite derived from wood, bark, or root material are few. Thus most of the plant organs and tissues have been preserved, but most of the humic material has experienced severe decay. The lignite is still highly liptinitic (as indicated by a high hydrogen index on programmed pyrolysis) even after wax extraction. Furthermore, the liptinitic fragments are not visibly altered by the extraction process. These observations suggest that the wax product is derived from cuticular waxes and not from 9resins or spores [ 118]. The lignites in Trinity County are entirely woody. The Covelo lignite contains abundant remains of fungal sclerotia. The lignite in the Reese deposit (Trinity County) has an ash value of about 15- 20% and a calorific value of 15.8-16 MJ/kg [116]. The seam thickness in the area of Ione is about 3.7 m with about 18 m of overburden [3]. Thicker, lenticular seams reaching 7.6 m in thickness occur at depths to 46 m [3]. The lignite beds near Ione and Buena Vista in Amador County vary in thickness from 1.2 to 9 m [ 154]. The Reese Deposit in Trinity County is 2.6 m thick [155]. The Temblor Formation (Miocene) contains four thin beds of lignite, each less than 90 cm thick [156]. The lignite seams lie in the upper 46 m of the formation. Despite the fact that California lignite deposits are small, the wax industry based on the solvent extraction of these lignites is an important one. The wax-from-lignite operation in California serves as an important reminder that lignites have potential uses other than combustion,
41 and that an assessment of their potential as sources of chemicals rather than as boiler fuels is overdue. 1.4.2 The Rocky Mountains (i) Colorado. Years ago lignite was obtained from underground mines in the areas around Ramah and Scranton. In some of the lignite-bearing areas east of Denver, mining started in 1887 [8]. Lignites occur about 24 km east of Denver, and continue southward into Adams, Arapahoe, and Elbert counties. Reserves of lignite accessible by strip mining are present in the Denver and Cheyenne basins [3]. The reserves remaining in the Laramie Formation are estimated at 18 Gt, and, in the Denver Formation, 9 Gt [1]. The Denver Formation may also contain up to another 900 Mt at depths greater than 300 m [1]. Large reserves of lignite occur in the Denver Formation (Paleocene) beneath the Dawson Arkose [3]. Adams, Arapahoe, Elbert and E1 Paso counties contain an estimated 900 Mt of lignite in areas with less than 60 m of overburden [3]. In the Denver Basin east and southeast of Denver there are estimated to be several Gt of lignite [120]. The Laramie Formation (Cretaceous) contains seven seams, of which No. 6 is the one most readily exploited. Strip mining potentially could occur in portions of Adams, Arapahoe, Boulder, and Weld counties, in a region roughly bounded by Eldorado Springs, Frederick, and Henderson. The coal seams in the Laramie Formation are lenticular, but may range up to 3 m in thickness [3]. The No. 6 seam contains coal which is at the lignite A / subbituminous C boundary, having a calorific value of 17.4-20 MJ/kg (as-received basis) [3]. Other properties of this coal, on an asreceived basis, are 22% moisture, 35% volatile matter, 8% ash, and 0.5% sulfur [3]. The lignite in the Denver Formation is brownish black. Like most lignites, it readily undergoes weathering, slacking, and disintegration. The moisture content is 22-40% and the calorific value is 9.3-17.4 MJ/kg [1]. Most of the coal is classified as lignite A, but some of the beds contain intervals that rank as subbituminous C. The lignite quality in the Denver Formation shows a wide range, having, on an as-received basis, 22-40% moisture, 8-30% ash, and 0.2-0.6% sulfur [3]. Lignite also occurs in the Denver Formation (Upper Cretaceous to Paleocene) [ 1]. Denver Formation lignites were deposited in swampy areas, and occur in sequences with shales, claystones, and sandstones. A useful compilation of lignite analyses from the Denver Region is available [ 121]. The overburden is composed of thick sandstones and conglomerates. Many of the lignite beds contain partings of kaolin which may range from about one cm in thickness to over 60 cm [ 1]. The seams become thinner southward in the Denver Formation, being 3-4.5 m thick in the north, and about 1.5-3 m thick in the south [3]. The multiple beds in the Denver Basin are relatively thick. The total thickness of lignite is 18 to 24 m [ 120], with the lignite beds separated by mudstones. The lignites lie at depths of 76 to 460 m [120]. (ii) Idaho. Lignites of poor quality occur in Cassia County southwest of Oakley [3]. The lower Salt Lake Formation (Tertiary) contains six seams, each 0.6 to 1.5 m thick, under less than 24 m of overburden [3]. The lignite quality, on an as-received basis, shows 20-35% moisture,
42 30- 60% ash, and 1-1.3% sulfur, with calorific values less than 11.6 MJ/kg [3]. 1.4.3 The Plains States (i) Kansas. The lignite reserves in Kansas are estimated to be 179 Mt [80]. The estimate is somewhat uncertain because the lignite beds are less than 76 cm in thickness, the minimum bed thickness accepted by the U. S. Geological Survey for estimating lignite reserves. Consequently the estimate is derived from the State Geological Survey of Kansas [ 122]. Lignite occurs in the Dakota Formation (Cretaceous) in the north-central part of the state. Lignite occurs in 19 counties. The lignite has been mined in at least 12 counties in the years 18751940. The original reserve of lignite in these 12 counties was 180 Mt [8]. The last active lignite mine was in Cloud County, and closed in 1940 [8]. The lignite was used for domestic heating and as a locomotive fuel. The lignite beds in Kansas are extremely variable in thickness. Seam thickness ranges from 5 cm to 3.7 m [8]. The sulfur content ranges from 0.48 to 6.28% [8]. The highest reported calorific value is 17 MJ/kg. (ii) Oklahoma. Lignite is found in the Purgatoire Formation in Cimmaron County. The Purgatoire Formation runs along the northwestern portion of the county, where the lignite seams are exposed in areas about 5 km apart [8]. The seam thickness is about 46 cm. The lignite has been mined on a local basis for domestic fuel. Two analyses of Oklahoma lignite indicate sulfur contents of 0.40-4).50% and calorific values of 17.6-19.8 MJ/kg [8]. 1.4.4 The Northwest (i) Washington. Small reserves of lignite occur in the Cedar Creek area of Lewis County. The reserves that could be recovered by strip mining amount to about 5 Mt [3]. The total identified resources of lignite in the Kelso-Castle Rock area are 114 Mt [1]. Some lignite occurs in the Skookumchuck Formation (late Eocene) in the Centralia-Chehalis area. Most of the coal in this formation is subbituminous C, and some is classified as subbituminous B. Most seams in the Skookumchuck Formation are 1.8-2.4 m thick, although the range of thickness runs from less than 30 cm to over 12 m [1]. The total identified resource in the Centralia-Chehalis Area (that is, including both lignite and subbituminous coal) is 3.4 Gt [ 1]. Coal occurs in the Cowlitz Formation (Eocene) and Toutle Formation (Oligocene) in the Kelso-Castle Rock Area. Most of the coal in the Cowlitz Formation is subbituminous C rank, though some lignite also occurs. All of the coal in the Toutle is lignite. Small reserves of lignites occur in the Cedar Creek No. 1 and No. 2 seams of the Toutle Formation. The seam thickness is in the range of 1.5 to 3 m [3]. The overburden thickness is 18 m, and the parting between the seams is about 3 m thick [3]. The analysis of one sample of Toutle Formation lignite is reported as 27.9% moisture, 28.0% volatile matter, 27.6% fixed carbon, 16.5% ash, 1.4% sulfur, and a calorific value of 15.7 MJ/kg, all on an as-received basis [ 1]. (ii) Alaska. The Kenai Formation in the Homer district includes about 30 coal beds that
43 range in thickness from 0.9 to 2 m, as well as additional, thinner beds [ 1]. The rank ranges from lignite through subbituminous B; most is subbituminous C. The Broad Pass coal field contains two districts, Broad Pass Station and Costello Creek. The latter contains subbituminous coal; the Broad Pass Station coal is lignite. Mine samples from the Broad Pass field show the following ranges of composition: 8.7-18.8% moisture, 32.043.4% volatile matter, 23.3--42.2% fixed carbon, 6.0--21.2% ash, 0.3-0.6% sulfur, and calorific values of 18.6-24.6 MJ/kg, all expressed on an as-received basis [1]. Alaskan lignites are generally of low sulfur content [ 123]. 1.5 O T H E R L I G N I T E S OF C A N A D A
1.5.1 Ontario Early reports, dating from the late 19th century, mention deposits of lignite and peat along the Missinaibi, Mattagami, and Abitibi rivers in the Moose River Basin, as well as some outlying deposits along the Kwataboahegan River. The lignite deposits near Coal River and at Blacksmith Rapids were considered to be of superior quality [ 134]. Ontario possesses 198 Mt of measured lignite resources [94]. The lignite deposit in the Mattagami Formation is estimated at 180 Mt [125]. The proven resources of the Onakawana field are 190 Mt [ 125]. A lignite deposit estimated to be less than 450 Mt is found in the James Bay area of northern Ontario [2]. A lignite deposit occurs in the southern Moose River Basin in the Onakawana field. It is not well studied; there is not as yet even a reliable estimate of reserves. In the Onakawana coal field the various lignite beds are fairly continuous, and are enclosed by clay. The lignite in the Onakawana field is low in ash and sulfur, but contains about 50% moisture [125]. The lignite in the Onakawana field between the Abitibi and Mattagami rivers seems to have the greatest potential for exploitation. The lignite-containing sequence includes a basal clay, a lower lignite seam of relatively constant thickness, a seam parting of clay, and an upper seam of variable thickness, overlain by clay. The average thickness of the lower seam is 4.2 m, reaching a maximum of 6 m along its southeastern limit near the Onakawana River [125]. The average thickness of the upper seam is 5.4 m [125]. The lignite consists of coalified wood, including recognizable tree trunks or branches, as well as more earthy lignite containing spores and resin inclusions. Some lignite may also occur on the east side of the Mattagami River, in the region running from the southeastern boundary of the Onakawana field toward Grand Rapids, with another potential deposit running westward from Onakawana. The Mattagami Formation (lower Cretaceous) underlies the southern part of the Moose River Basin adjacent to the Canadian Shield in northern Ontario. The lignite is relatively thick and of low sulfur content, but generally of high moisture. The age of the lignite in the Moose River Basin (Mesozoic) was established from fossil plants [126]. The Mattagami Formation is 119 meters thick [ 125]. Limited data suggest that the lignite in the southern Moose River Basin is about
44 50% moisture, 22% volatile matter and 6% ash on an as-mined basis, 0.9% sulfur (daf basis) and provides 14 MJ/kg calorific value (moist basis) [94]. The principal lignite beds in the Mattagami Formation occur on Coal River at the juncture with the Missinaibi River, near the confluence of Adam Creek with the Mattagami River, at Blacksmith Rapids on the Abitibi River near Onakawana, and at Portage Island at the confluence of the Missinaibi and Mattagami rivers. Early studies of the lignite exposures at Coal River indicated a bed 0.9 m thick [127]. laalynological studies of the lignite confirmed the early Cretaceous age, either Early Albian or Middle Albian or Aptian [128]. 1.5.2 British Columbia Measured resources of lignite in British Columbia and the Yukon are 1,670 Mt, classified as indicated resources [94]. The reserves recoverable by surface mining are 360 Mt [94]. The coal reserves in the Hat Creek deposit amount to 360 Mt [94]. The Hat Creek deposit contains large reserves of low-rank coal, both lignite and subbituminous. The lignite is variable in quality. The ranges for the proximate analyses are 20-23% moisture, 24-30% volatile matter, and 8-23% ash, on an as-mined basis [94]. Sulfur ranges from 0.5-0.8% on a daf basis. The calorific value is 11.6-22.1 M.l/kg on a moist basis. The lignite ash has high fusion temperatures [94].
1.5.3 The Canadian Arctic The existence of coal-bearing strata in the Tintina Trench has been known since the gold rush era in the late nineteenth century [ 129]. Early in the 20th century, the coal near Dawson was mined, some of the coal being used in an electric power plant. The Gates Mine worked the lignite along Coal Creek in 1898 to 1903, and again briefly in 1937 [130]. Another mine on Coal Creek supplied fuel until 1914 for a power station providing electricity for the gold dredges operating in the Klondike. Mining also occurred along Cliff Creek from 1898 to 1903. More recently, however, there has been little interest in mining the lignite because of its low rank, the complexity of the geologic structures, and the distance from potential markets. Some interest was sparked in the 1970's by the proposed construction of a natural gas pipeline from the Mackenzie Delta and Prudhoe Bay gas fields. It was thought that the lignite could be used to fire local electric power stations which would provide the necessary power for the gas pumping stations. Lignite in the Yukon and Northwest Territories exists in seams up to 9 m thick [95]; however, most of the data comes only from outcrops. Exploration of the lignite resource has so far been limited. The strata of the Eureka Sound Formation contain major deposits of lignite. This formation occurs in the Canadian Arctic Archipelago, running northward from Banks and Baffin Islands to Ellesmere Island. The Remus Basin on Ellesmere Island contains over 90 seams of coal in a section approximately 3,200 m thick [131]. The coals in this section are lignites and subbituminous and high volatile bituminous coals. Some lignite seams on Axel Heiberg Island are 7 m thick. In the southern part of the Remus Basin the lignite is the most resistant unit in the stratigraphic
45 sequence. In some places ridges are capped with lignite seams up to 25 m thick [ 131 ]. The total inferred coal resources of the Eureka Sound Formation are about 50 Gt [131]. On the basis of limited analytical data, the coal of the Eureka Sound Formation appears to be low sulfur (<1%) with highly variable ash content, although seams with less than 10% ash occur. The range of calorific values is 23-33 MJ/kg (moist, mineral-matter-free basis). Huminite or vitrinite macerals account for 70-90% of the coal [131 ]. Coal-bearing strata of Early Tertiary age (Paleocene-Eocene) occur in the Tintina Trench in southern and central Yukon Territory [130]. The coal ranges in rank from lignite to semianthracite. The seams occur near Watson Lake, Ross River, and in the region between Dawson and the border with the United States. (The very high rank coals were formed by thermal upranking by magmatic intrusions.) Some thin seams of poorly characterized coal also occur in the areas around Dawson and Watson Lake. The complex geological structure of the Tintina Trench (lateral movement along some 450 km during the Cretaceous, and possible further movement more recently than the Eocene, have been postulated), as well as the lateral variability of the coal and the restricted extent of the coalbearing strata make it difficult to evaluate the potential of the resource. The coal having some potential for mining occurs in the vicinity of Dawson and Ross River [ 130]. The only practical approach to mining the coal would be surface mining, and that approach may be made difficult by the thickness of the surface deposits. The thickest exposure of coal occurs along the east side of the Laird River, about 2 km from the confluence with the Rancheria River [ 130]. Here five seams occur, ranging in thickness from 0.4 to 2.1 m [ 130]. Several thinner beds have also been reported. The coal is of lignite A and lignite B rank. Abundant plant remains are evident. When the lignite is weathered, the annular rings of logs can be separated easily. Resin occurs in nodules of up to 1 cm maximum thickness, as well as in lenticular layers up to 2 cm thick [168]. The ash content of the lignite in the thickest seam is about 50% [ 130]. 1.5.4 Nova Scotia Based on samples from two bore holes for Nova Scotia lignites, the as-received moisture and ash contents range from 5.02 to 10.13% and 8.67 to 49.85%, respectively. As-received calorific values were 11.3 and 23.1 MJ/kg. Equilibrium moistures were 30.13 and 34.79%. The ASTM rank classification for both samples was lignite A, with corroboration by vitrinite reflectance [ 132].
46 REFERENCES
9 10 11 12 13
14
15 16 17 18 19 20 21 22 23 24 25
Energy Resources Co., Low-rank coal study. Volume 2, Resource characterization, U.S. Dept. Energy Rept. DOE/FC/10066-TI(Vol.2), 1980. B. I gnasiak, D. Carson, A.J. Szladow, and N. Berkowitz, Studies on non-catalytic liquefaction of western Canadian coals, Prepr. Pap. Amer. Chem. Soc. Div. Fuel Chem., 24(2) (1979) 40-47. E.A. Elevatorski, Strip-Mineable Coals Guidebook, Minobras, Dana Point, CA, 1980. Energy Resources Co., Low-rank coal study. Volume 3, Technology evaluation, U.S. Dept. Energy Rept. DOE/FC/10066-TI(Vol.3), 1980. P.A. Hamilton, D.H. White, Jr., and T.K. Matson, The reserve base of U.S. coals by sulfur content. Part 2, The western states, U.S. Bur. Mines Info. Circ. 8693, (1975). J.L. Riddell, Observations on the geology of the Trinity country, Texas, Amer. Jour. Sci., 37 (1839) 211-217. W.L. Fisher, Lignites of the Texas gulf coastal plain, Texas Bureau of Economic Geology Rept Invest. 50, (1963). Staff, U.S. Bureau of Mines, Strippable reserves of bituminous coal and lignite in the United States, U.S. Bur. Mines. Info. Circ. 8531 (1971). W.B. Phillips, Coal, lignite, and asphalt rocks, University of Texas Bull. 15, (1902). S. Powers, Interior salt domes of Texas, Bull. Amer. Assoc. Petrol. Geol., 10 (1926) 160. J.W. Dietrich and J.T. Lonsdale, Mineral resources of the Colorado River Industrial Development Association area, Texas Bureau of Economic Geology Rept Invest. 37, (1958). M.L. Wilson and C.D. Rao, Gulf coast lignite development and policy, in: W.R. Kube, E.A. Sondreal, and C.D. Rao (Eds.), Technology and utilization of low-rank coals, U.S. Dept. Energy Rept. DOE/METC/84-13 Vol. 1, (1984), pp. 17-46. W.B. Ayers, Jr., and W.R. Kaiser, Regional depositional setting, resources, and quality of lignite in the Wilcox group of east Texas and the Jackson group of east and south Texas, in: R.B. Finkelman and D.J. Casagrande (Eds.), Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 69-114. T.F. Edgar, W.R. Kaiser, M.J. Humenich, and H.B.H. Cooper, Technical, economic, and environmental factors for in-situ gasification of Texas lignite, in: W.R. Kube and G.H. Gronhovd (Eds.), Technology and use of lignite, U.S. Dept. Energy Rept. GFETC/1C79/1, (1979) pp. 207-231. W.R. Kaiser, W.B. Ayers, Jr., and L.W. LaBrie, Lignite resources in Texas, Texas Bureau of Economic Geology Rept. Invest. 104 (1980). W.L. Fisher and W.R. Kaiser, Lignite: the other fuel of Texas, Texas Business Review, 4 (1974) 86-90. W.R. Kaiser, Texas lignite: near-surface and deep basin resources, Texas Bureau of Economic Geology Rept. Invest. 79 (1974). D.M. White, W.R. Kaiser, and C.G. Groat, Status of gulf coast lignite activity, in: W.R. Kube, E.A. Sondreal, and D.M. White (Eds.), Technology and use of lignite, U.S. Department of Energy Report GFETC/IC-82/1, (1982) pp. 107-141. J.C. Lacy and D.M. White, The future of Texas lignite, in: W.R. Kube and G.H. Gronhovd (Eds.), Technology and use of lignite, U.S. Department of Energy Report GFETC/1C-79/1, (1979) pp. 426-458. W.R. Calvert, Geology of certain lignite fields in eastern Montana, U.S. Geol. Surv. Bull. 471 (1912). W.H. Calkins and W. Spackman, Tracing the origins of polymethylene moieties in coal, Intl. Jour. Coal Geol., 6 (1986) 1-19. E.H. Sellards and C.L. Baker, The geology of Texas. II. Structural and economic geology, University of Texas Bull. 3401 (1935). W.L. Fisher, Rock and mineral resources of east Texas, Texas Bureau of Economic Geology Rept. Invest. 54 (1965) W.H. Holmes, Report on the San Juan district, U.S. Geol. Surv. Ann. Rept.. 9 (1877) 237-276. W.A. Selvig, W.H. Ode, B.C. Parks, and H.J. O'Donnell, American lignites: geological
47
26 27 28 29 30 31
32 33 34 35 36 37 38 39 40
41 42 43 44 45 46 47 48 49
occurrence, petrographic composition, and extractable waxes, U.S. Bur. Mines Bull. 482, (1950). W.R. Kaiser, J.E. Johnston, and W.N. Bach, Sand-body geometry and the occurrence of lignite in the Eocene of Texas, Texas Bureau of Economic Geology Circ. 78-4, (1978). D.J. Nichols and A. Traverse, Palynology, petrology, and depositional environments of some early Tertiary lignites in Texas, Geosci. Man, 3 (1971) 37-48. B.C. Pollard, J.B. Smith, and C.C. Knox, Strippable lignite reserves of North Dakota, U.S. Bureau of Mines Info. Circ. 8537 (1972). W.L. Fisher and J.H. McGowen, Depositional systems in the Wilcox group of Texas and their relationship to the occurrence of oil and gas, Trans. Gulf Coast Assoc. Geol. Socs., 17 (1967) 105-125. D.J. Nichols, Palynology in relation to depositional environments of lignites in the Wilcox Group (E. Tertiary) in Texas, Ph.D. Dissertation, The Pennsylvania State University, University Park, PA, 1970. J.E. McNulty, Jr., Geology of the San Miguel lignite deposit (Atascosa and McMullen counties, Texas), in: W.R. Kaiser (Ed.), Gulf coast lignite conference: geology, utilization, and environmental aspects, Texas Bureau of Economic Geology Rept. Investi. 90, (1978), pp. 79-83. W.E. Ward II, Reserve base of bituminous coal and lignite in Alabama, U.S. Department of Energy Report DOE/ET/12507-T1 (1984). D.M. Self, Lignite resources of the Alabama-Tombigbee Rivers region, Alabama, in: W.R. Kaiser (Ed.), Gulf coast lignite conference: geology, utilization, and environmental aspects, Texas Bureau of Economic Geology Rept. Invest. 90, (1978), pp. 59-65. D.R. Williamson and W.L. Prior, Lignites of Alabama, Arkansas, and Mississippi, in: R.B. Finkelman and D.J. Casagrande (Eds.), Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 115-125. T.W. Daniel, Jr., A strippable lignite bed in south Alabama, Alabama Geol. Surv. Bull. 101, (1973). O.M. Clarke, Jr., T.W. Daniel, Jr., and M.W. Szabo, Mineral resources of Wilcox County, Alabama, Alabama Geol. Surv. Circ. 66, (1970). R.N. Miller and P.H. Given, A geochemical study of the inorganic constituents in some low-rank coals, U.S. Department of Energy Report FE-2494-TR- 1, (1978). P.H. Given and R.N. Miller, Distribution of forms of sulfur in peats from saline environments in the Florida Everglades, Abstr. Prog., Geol. Soc. Amer. 3(7) (1971) 580. E.A. Mancini, Paleocene lignite deposits of southwest Alabama, Bull. Amer. Assoc. Petrol. Geol., 68 (1984) 502-505. D.M. Self and D.R. Williamson, Occurrence and characteristics of Midway and Wilcox lignites in Mississippi and Alabama, in: M.D. Campbell (Ed.), Geology of Alternate Energy Resources in the South-Central U.S., Houston Geological Society, Houston, 1977, pp. 161-177. R. Gutzler, Petrology and depositional environments of Tertiary lignite in Alabama, Ph.D. Dissertation, The Pennsylvania State University, University Park, PA, 1978. C.H. Dane, Upper Cretaceous formations of southwestern Alabama, Arkansas Geol. Surv. Bull. 1, (1929). P.A. Sokolosky and C.G. Musgrove, Alabama coal data, Alabama Geol. Surv. Info. Ser. 58 (1982) 1-112. G.C. Branner, Mineral resources of Arkansas, Arkansas Geol. Surv. Bull. 6, (1942). H.V. Andersen, Geology of Sabine Parish, Louisiana Dept. Conservation Geol. Bull. 34, (1960). H.V. Howe and C.K. Moresi, Geology of Iberia Parish, Louisiana Dept. Conservation Geol. Bull. 1, (1931). H.L. Roland, Jr., Louisiana lignite, in: W.R. Kaiser (Ed.), Gulf coast lignite conference: geology, utilization, and environmental aspects, Texas Bureau of Economic Geology Rept. Invest. 90, (1978), pp. 66-78. D.R. Williamson, Lignites of northwest Louisiana and the Dolet Hills lignite mine, in: R.B. Finkelman and D.J. Casagrande (Eds.), Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 13-28. H.H. Doney, Recent and current research on Wilcox lignite in northern Louisiana, in: R.B.
48
50 51 52 1t3
54 55 56 57 58 59 60 61 62 63 64 65
56
67 58 59 70 71 72 73 74
Finkelman and D.J. Casagrande (Eds.), Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 156-186. D.P. Meagher and L.C. Aycock, Louisiana lignite, Louisiana Dept. Conservation Geol. Pamphlet 3, (1942). D.R. Williamson, The Tertiary lignites of Mississippi, in: W.R. Kaiser (Ed.), Gulf coast lignite conference: geology, utilization, and environmental aspects, Texas Bureau of Economic Geology Rept. Invest. 90, (1978), pp. 54-58. J.L. Hainer, The geology of North Dakota, North Dakota Geol. Surv. Bull. 31, (1956). B. DeVoto, The Journals of Lewis and Clark, Houghton Mifflin, Boston, 1953. F.V. Hayden, On the geology and natural history of the upper Missouri, Trans. Amer. Philos. Soc., XII (1862) 1-218. C.I. Frye, Stratigraphy of the Hell Creek formation in North Dakota, North Dakota Geol. Surv. Bull. 54, (1969). F.B. Meek and F.V. Hayden, Proc. Phila. Acad. Sci. 13 (1862) 433. A.M. Cvancara, Lignite - valuable resource of North Dakota, in: Department of Geology, University of North Dakota (Eds.), Contributions to the geology of North Dakota, North Dakota Geol. Surv. Bull. 28, (1955). J.R. LaFevers, D.O. Johnson, and A.J. Dvorak, Extraction of North Dakota lignite: environmental and reclamation issues, Argonne National Laboratory Rept. ANL/AA-7, (1976). A.C. Fieldner, Analyses of Michigan, North Dakota, South Dakota, and Texas coals, U.S. Bur. Mines Tech. Paper 700, (1948). R.A. Brant, Lignite resources of North Dakota, U.S. Geol. Surv. Circ. 226, (1953). League of Women Voters, Coal development in North Dakota, League of Women Voters, Fargo, ND, 1974. E.A. Noble, Mineral and water resources of North Dakota, North Dakota Geol. Surv. Bull. 63, (1973). W.R. Calvert, Geology of certain lignite fields in eastern Montana, U.S. Geol. Surv. Bull. 471, (1912). L.C. Gerhard, S.B. Anderson, J.A. Lefever, and C.G. Carlson, Geological development, origin, and energy mineral resources of the Williston Basin, North Dakota, North Dakota Geol.1 Surv. Miscellaneous Series 63, (1982). C.F. Royse, Jr., The Tongue River and Sentinel Butte Formations (Paleocene) of western North Dakota, in: F.C. Ting (Ed.), Depositional environments of the lignite-bearing strata in western North Dakota, North Dakota Geol. Surv. Miscellaneous Series 50, (1972), pp. 31-42. C.S.V. Barclay, The Tongue River and Sentinel Butte members of the Fort Union formation near Glen Ullin, Morton County, North Dakota, in: F.C. Ting (Ed.), Depositional environments of the lignite-bearing strata in western North Dakota, North Dakota Geol. Surv. Miscellaneous Series 50, (1972). M. Hansen, Lignite in North Dakota, North Dakota Geol. Surv. Miscellaneous Series 23, (1964). S.R. Moran, G.H. Groenewold, L.A. Hemish, and C.A. Anderson, Development of a premining geological framework for landscape design reclamation in North Dakota, Proc. Fort Union Coal Field Symp., Mont. Acad. Sci., 3 (1975) 308-316. W.B. Roe, Econ. Geol., 45 (1950) 434-440. C.J. Hares, Geology and lignite resources of the Marmarth field, southwestern North Dakota, U.S, Geol. Surv. Bull. 775, (1928). G.H. Groenewold, L.A. Hemish, J.A. Cherry, B.W. Rehm, G.N. Meyer, and L.M. Winczewski, Geology and geohydrology of the Knife River basin and adjacent areas of west-central North Dakota, North Dakota Geol. Surv. Rept. Invest. 64, (1979). W.D. Johnson, Jr., and R.P. Kunkel, The Square Buttes coal field, Oliver and Mercer counties, North Dakota, U.S. Geol. Surv. Bull. 1076, (1959). S.A. Benson, J.P. Hurley, and E.N. Steadman, Distribution of inorganics, in: G.A. Wiltsee (F_xi.), Low-rank coal research, U.S. Dept. Energy Rept. DOE/FE/60181-1642, (1984), Section 15. R.G. Roaldson, Inorganic constituents of a stratigraphic section of Center mine seam #1, University of North Dakota Energy Research Center Report IR-3, Grand Forks, ND,
49 75 76 77 78
79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94
95 96 97 98 99 100
1983. L. Clayton, Roadlog, in: F.C. Ting (Ed.), Depositional environments of the lignite-bearing strata in western North Dakota, North Dakota Geol. Surv. Miscellaneous Series 50, (1972), pp. 2-30. A.G. Leonard, E.J. Babcock, and L.P. Dove, The lignite deposits of North Dakota, North Dakota Geol. Surv. Bull. 4, (1925). United States Bureau of Mines Staff, Technology of lignitic coals, U.S. Bur. Mines Info. Circ. 7691, (1954). L.C. Hamngton, Analyses of lignite samples from two hundred forty-five mines under lignite survey and investigation by Federal Emergency Relief Administration Project S-F256, University of North Dakota Division of Mines and Mining Experiments Circular 8, Grand Forks, ND, 1934. S.A. Cooley and R.C. Ellman, Analyses of Northern Great Plains province lignites and subbituminous coals and their ash, U.S. Dept. Energy Rept. DOE/GFETC/RI-81/2, (1981). P. Averitt, L.R. Berryhill, and D.A. Taylor. Coal resources of the United States. A progress report, October 1, 1953, U.S. Geol. Surv. Circ. 293, (1953). J.X. Combo, D.M. Brown, H.F. Pulver, and D.A. Taylor, Coal resources of Montana, U.S. Geol. Surv. Circ. 53, (1949). F. Calcagno Jr. and G.H. Westman, Resource and potential reclamation evaluation: northeast Montana investigation report, U.S. Bur. Reclam. Rept. PB-84-112390 (1983). F. Calcagno Jr. and G.H. Westman, Resource and potential reclamation evaluation of northeast Montana investigations, Dawson and McCone Counties, Montana, U.S. Bur. Reclam. Rept. PB-84-112408 (1983). F.B. Meek and F.V. Hayden, Proc. Phila. Acad. Sci., 13 (1862) 415-432. R.E. Matson and J.M. Pinchock, Geology of the Tongue River member, Fort Union formation of eastern Montana, in: D.K. Murray (Ed.), Geology of Rocky Mountain coal, Colorado Geol. Surv. Resource Series 1, (1976) pp. 91-114. R.E. Matson, G.G. Dahl, Jr., and J.W. Blumer, Strippable coal deposits on state land, Powder River county, Montana, Montana Bur. Mines and Geol. Bull. 69, (1968). U.M. Sahinen, Mineral resources of Richland county, Montana, Montana Bur. Mines Geol. Info. Circ. 10, (1956). W.M. Johns, Geology and mineral deposits of Lincoln and Flathead counties, Montana, Montana Bur. Mines Geol. Bull. 79, (1970). H. Wood, Eng. Mining Jour., 54(3) (1892) 57-63. R.E. Matson and J.W. Blumer, Quality and reserves of strippable coal, selected deposits, southeastern Montana, Montana Bur. Mines Geol. Bull. 91, (1973). R.E. Matson, Strippable coal in the Moorhead coal field, Montana, Montana Bur. Mines Geol. Bull. 83, (1971). E.H. Gilmour and L.A. Williams, Geology and coal resources of the Foster Creek coal deposit, eastern Montana, Montana Bur. Mines Geol. Bull. 73, (1969). A.S. Romaniuk and H.G. Naidu, Coal mining in Canada: 1983, Canada Centre for Mineral and Energy Technology Rept. 83-20E, (1984). G.K. Lee, T.D. Brown, F.D. Friedrich, and H. Whaley, Canadian low-rank coals: resources, conversion, and utilization, in: W.R. Kube, E.A. Sondreal, and D.M. White (Eds.), Technology and use of lignite, U.S. Dept. Energy Rept. GFETC/IC-82/1, (1982), pp. 162-188. G.R. Couch, Lignite resources and characteristics, International Energy Agency Report (draft), London, 1988. J.H. Dyck, C.T. McKenzie, T.E. Tibbetts, and S.H. Whitaker, Quality and occurrence of coal in southern Saskatchewan, Canada, Saskatchewan Research Council Rept. ERP/ERL80-84(TR)Vol. 1, (1980). A.R. Cameron and T.F. Birmingham, Petrographic and chemical properties of a lignite from Estevan, Saskatchewan, Geol. Surv. Canada Paper 71-8, ( 1971). Anonymous, Coal in Saskatchewan, Coal Miner, 8(2) (1983) 12-14. P. Averitt, Coal resources of the United States, January 1, 1974, U.S. Geol. Surv. Bull. 1412, (1975). G.B. Glass, Wyoming coal deposits, in: D.K. Murray (Ed.), Geology of Rocky Mountain
50 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132
coal, Colorado Geol. Surv. Resource Series 1, (1976), pp. 73-84. H.L. Berryhill, Jr., D.M. Brown, A. Brown, and D.A. Taylor, Coal resources of Wyoming, U.S. Geol. Surv. Circ. 81, (1950). P. Averitt and L.R. BeITyhill, Coal resources of the United States, U.S. Geol. Surv. Circ. 94, (1950). D.J. McGregor, Mineral and water resources of South Dakota, South Dakota State Geol. Surv. Bull. 16, (1964). E.P. Rothrock, A geology of South Dakota. Part III. Mineral resources, South Dakota Geol. Surv. Bull. 15, (1944). N.M. Denson, The lignite deposits of the Cheyenne River and Standing Rock Indian reservations: Corson, Dewey, and Ziebach counties, South Dakota and Sioux county, North Dakota, U.S. Geol. Surv. Cir. 78, (1950). D.M. Brown, Lignite resources of South Dakota, U.S. Geol. Surv. Circ. 159, (1952). D.E. Winchester, The lignite fields of northwestern South Dakota, U.S. Geol. Surv. Bull. 627, ( 1916). W.V. Seafight, The Stoneville coal area, So. Dakota Geol. Surv. Rept. Invest. 22, (1934). J.J. Crawford, Coal - Trinity county, California Mining Bur. Rept. 13, (1896). J.C. O'Brien, Mines and mineral resources of Trinity county, California, California Div. Mines Geol. County Report 4, (1965). E.W. Hart, Mines and mineral resources of Monterey county, California, California Div. Mines Geol. County Report 5, (1966). W. Irelan, Jr., Monterey County, California Mining Bur. Rept. 8, (1888). J.J. Crawford, Asphaltum and bituminous rocks, coal, golf, mineral springs, structural materials, California Mining Bur. Rept. 13, (1896). C.M. Laizure, Monterey county, California Mining Bur. Rept. 21, (1925). C.A. Logan, Trinity county, California Mining Bur. Rept. 22, (1926). C.V. Averill, Mineral resources of Trinity county, Calif. J. Mines Geol., 37 (1941) 8-36. B.C. Parks, Petrography of American lignites, Econ. Geol., 46 (1951) 23-50. N.H. Bostick, Petrographic and chemical character of Tertiary coals in northern California, Abstr. Soc. Org. Petrol., 4 (1987) 7-8. P.D. Trask, Geology of Point Sur quadrangle, California, Univ. Calif. Dept. Geol. Sci. Bull., 16 (1926) 119-186. P. Soister, Colorado lignite for underground coal gasification, in: S.R. Hudson (Ed.), Proceedings of the eighth underground coal conversion symposium, U.S. Dept. Energy Rept. SAND-82-2355, (1982), pp. 389-393. N.S. Khalsa abd C.R. Campbell, Chemical analyses of coal samples from the Denver region, Inf. Ser. Colo. Geol. Surv. 10 (1981) 33-63. W.H. Schoewe, Current coal research- coal geology in Kansas, Econ. Geol., 46 (1951) 852-856. R.D. Merritt, G.R. Eakins, and J.G. Clough, Coal investigation of the Susitna Lowland, Alaska, Alaska Open File Rep. 142 (1982). J.M. Bell, Economic resources of the Moose River basin, Ont. Bur. Mines 13 (1904) 135179. L.L. Price, Mesozoic deposits of the Hudson Bay lowlands and coal deposits of the Onakawana area, Ontario, Geol. Surv. Canada Paper 75-13, (1978). J. Keele, Mesozoic clays in northern Ontario, Geol. Surv. Canada Rept. G, (1919). R. Bell, Report on exploration in 1875 between James Bay and Lakes Superior and Huron, Geol. Surv. Canada Repts. Progress for 1875-1876, pp. 294-342. W.S. Hopkins and A.R. Sweet, Miospores and megaspores from the lower Cretaceous Mattagami formation in Ontario, Geol. Surv. Canada Bull. 256, (1976). R.G. McConnell, Lignite areas, Geol. Surv. Canada Ann. Rept., Volume SIII, Part A, (1903), pp. 44-48. J.D. Hughes and D.G.F. Long, Geology and coal resource potential of early Tertiary strata along Tintina trench, Yukon Temtory, Geol. Surv. Canada Paper 79-32, (1980). R.M. Bustin, Organic maturity of late Cretaceous and Tertiary coal measures, Canadian arctic archipelago, Intl. Jour. Coal Geol. 6 (1986) 71-106. P.A. Hacquebard, Composition, rank and depth of burial of two Nova Scotia lignite deposits, Geol. Surv. Canada Paper 84-1A, (1984).
51
Chapter 2
THE DEPOSITION AND FORMATION OF LIGNITE 2.1 I N T R O D U C T I O N This chapter treats the origin of lignite. Three major topics are discussed: first, the plant material that accumulated and eventually transformed to lignite; second, the environments in which the plant material was deposited; and third, the chemical changes occurring in the plant material leading to the formation of lignite. The third section, on coalification reactions, provides a connection to the material presented in Chapter 3, which treats in detail the organic structure of lignites at the macroscopic, microscopic and molecular levels. 2.2 PALEOFLORA Conifers predominated in the paleofloral assemblages giving rise to the lignites of the northern Great Plains [1]. Consequently, these lignites consist largely of woody material with relatively small amounts of attritus or plant debris. In contrast, lignites of the Gulf Coast region largely formed from angiosperms. Conifers were a minor component of the paleoflora of the Texas lignites. For these reasons, the discussion which follows is divided to treat separately the lignites of these two regions. 2.2.1 Northern Great Plains paleoflora The flora of the Golden Valley Formation (Paleocene-Eocene, western North Dakota) have been divided into three general associations: aquatic and marsh vegetation, lowland forest flora, and upland plants, with a fourth category of plants of uncertain classification [2]. Palynoflora of the Hagel bed (North Dakota) were dominated by gymnosperms, with fewer angiosperms and pteridophytes [3], based on samples collected at the Falkirk, Glenharold, and Center mines. Angiosperms make a much higher contribution to the Falkirk lignite than to the Center or Glenharold lignites. Center lignite contained the greatest amount of pteridophytes, which relates to its also having the greatest number of claystone-lignite contacts. Such contacts typically display high percentages of pteridophytes. Vertical variations in the three mines show similar patterns: the
Taxodiaceae-Cupressaceaegymnosperms always dominate; angiosperms usually are
more abundant near the seam margins; and ptreidophytes have greater abundance at the claystonelignite contacts.
52 Gymnosperms dominate throughout the Center mine lignite. An increasing abundance of angiosperms near the seam margins suggests their relationship with detrital material, as discussed below. Angiosperm abundance also increases near the seam margins in the Glenharold lignite. Angiosperms were more consistently a major element in Falkirk lignite relative to the Center and Glenharold lignites, whereas pteridophytes were comparatively reduced in abundance. The abundances of various palynomorphs, expressed by paleoenvironmental groups, show that fern-conifer swamp taxa dominate almost completely; in general, the palynoflora are consistent and relatively constant [3]. An increase in angiosperm pollen in lignite near claystone and siltstone layers, and angiosperm pollen in the claystones, indicates the riparian character of the angiosperms. The riparian characteristic and the association with the clastics both suggest that angiosperm pollen mainly transported into the depositional environment as detrital material. The increase of pteridophytes at the claystone-lignite contacts represents a successional change with changing environment; the pteridophytes may have been the first flora to colonize the clay surface with a change in the paleoenvironment to favor peat deposition. Such a change represents the beginning of autochthonous deposition of organic matter. Fern spore palynomorphs have been related to open swamp and lake fringing environments [4]. Palynomorphs indicative of a cypress forest - swamp environment dominate throughout the Center, Falkirk, and Glenharold lignites. Fem types such as Osmunda, indicative of swampy conditions, are also common constituents. Steriosporites antiquasporites suggest floating peat islands similar to those in the modem Okefenokee Swamp [5]. Riparian species dominate the deciduous flora. Preserved plant tissues, both macroscopic xylites and microscopically observable coalified wood, indicate deposition in a watery environment where the water provided protection from decay. This environment is common in forest swamps with abundant standing water [6]. A fluctuating variation between the conifers (Taxodiaceae--Cupressaceae)and the angiosperms (Myriceae--Betulaceae)occurred in lignites from Harding County, South Dakota and Billings County, North Dakota [7]. Water depth controlled the fluctuation between conifers and angiosperms [7]. Lignite in those portions of the Harding County seam with high concentrations of
Taxodiaceae-Cupressaceae pollen also had high amounts of anthraxylous material [8]. In comparison, high concentrations of cuticular debris and attrital resins characterized those portions of the seam with correspondingly high concentrations of Myricaceae--Betuilaceae pollen [7]. The near-surface lignites of Late Cretaceous-Early Tertiary age in Alberta derive from
Taxodiaceae (particularly bald cypress trees) [9]. Older lignites (Early Cretaceous) derive from pines of the family Podocarpaceaeas well as extinct conifers such as Cheirolepidiaceae. Resin inclusions are attributable to the dominance of conifers in the paleoflora [ 1]. Lignites near Gore, New Zealand contain remarkable resin inclusions the size of a human head [ 10]. 2.2.2 Gulf Coast paleoflora Wilcox (Texas) lignites and related sediments contain fossils representative of tropical, subtropical, and temperate flora; however, the dominant climate was subtropical to tropical [ 11].
53 The maximum climatic warming occurred during deposition of the Claiborne sediments, which overlie the Wilcox [ 12]. By the time the Jackson sediments were deposited, the climate had cooled, resulting in a shift to more temperate conditions. The presence of oak pollen in the Jackson, but not in the Wilcox, supports this concept [13,14].
Normapolle and Engelhardia pollen predominate in the Midway and Wilcox lignites and associated sediments of the Gulf Coast, along with pollen of extinct Juglandaceae [4,13]. Other distinctive pollen in these sediments include Engelhardia dilatus, Sernapollenites, and
Thomsonipollis [4]. Thomsonipollis is common throughout the Wilcox. The Wilcox lignites of Mississippi show a pollen and spore assemblage typical of lowland swamp flora occupying a subtropical coastal plain, with contributions from the temperate flora of the foothills of the Southern Appalachians. The first discovery of Nipadites (the fruit of a nipa palm) in the paleoflora of the Western Hemisphere, Nipadites burtini umbonatus Bowerbank, was in lignite from Grenada County, Mississippi [15]. In the Cretaceous McNairy Formation lignites of Kentucky, the most abundant taxa were
Cupuliferoidaepollinites and Taxodiaceaepollinites [16]. The latter were more important in Cretaceous than in Eocene lignites. The most abundant spore in the McNairy lignites was
Stereisporites, which indicates Sphagnum peat [ 16]. Angiosperm flora dominated the Claiborne lignites in Kentucky. Important, and relatively wide-ranging, flora included Momipites-Engelhardia, TricolporopoUenites, Cupuliferoipollinites, and Cupuliferoidaepollenites liblarensis [161. Calvert Bluff (Wilcox) lignites consist of woody tissue, with the woody structure still evident, some cellular material which is probably epidermal, and palynomorphs which are sparse to common [4]. Swamp tree pollen dominates the palynomorphs, the Betulaceae--Myricaceae,
Nyssa, and Thomsonipollis, consistent with this lignite having formed in a swamp between a low alluvial plain and a higher delta plain [ 17]. Sphagnum is common in some Calvert Bluff lignites. Palynomorphs indicative of a marshy environment--Calamuspollenites-Arecipites, Carex, and Liliacidites--occur at the beginning of the Calvert Bluff and then only infrequently throughout the deposit. Engelhardia are also common in the Calvert Bluff; however Betulaceae--Myricaceae pollen and Sphagnum spores dominate typical Calvert Bluff lignites. (The latter flora are also common in Alabama lignites.) The Betulaceae--Myricaceae and Sphagnum indicate a swampy environment. A high percentage of vitrite and clarite microlithotypes occurs in the lower two-thirds of the Chemard Lake Lentil lignite (Louisiana) [18]. Carya and TriporopoUenites bituitus are abundant in the associated paleofloral assemblage. Durite and clarodurite increase toward the top of the seam. The duroclarite and carbominerite macerals contain pollen of Engelhardia
and
Microreticulatosporites. The lignite was deposited in a fresh water swamp on an upper deltaic plain dominated by hardwoods. The Red Seam lignite was deposited in the same environment as the Sunrise lignite [ 18]. The composite pollen assemblage for the Sunrise and Chemard Lake lignites shows three main elements: ferns (Triplanosporite--Deltoidosporite group), conifers (Taxodium),
54
and deciduous arboreal pollen such as the hazelnut (Bemlaceae) and hickory (Juglandaceae) [ 19]. Palynomorphs recovered from the Chemard Lake lignite included 51 genera and 67 species. The palynomorph assemblage indicated an upper deltaic swamp dominated by angiosperms such as
Tricolpopollenites h i ans , Triporopollenites bituitus, Triatriopollenites arboratus, and Thomsonipollis magnificus [19]. Several genera and species of the Nomapollis group occur in older Wilcox sediments, but only one is found in the Claiborne [11]. A marked change in flora occurred between the Wilcox and Claiborne. Palynomorphs that either reach a maximum in, or are unique to, the Claiborne include Amonoa, Nymphaea, Bombapollis, Bombacacidites claibornensis, Nyssapollenites,
Enopodios, Yeguapollis, and Nuxpollenites, as well as the tropical or subtropical Burseraceae, Sapotaceae, Sapindaceae, Alangiaceae, and Bombacaceae [4,11]. Yegua lignites contain structured woody tissue, and in addition commonly contain a coarse, amorphous material. Both Engelhardia and Nyssa pollen are common to abundant; Amanoa is sparse to common [4]. These palynomorphs indicate deposition in a swampy environment.
Polypodium spores are common in Yegua and Manning lignites; ferns of this type grow in open areas of the swamp or in marshy conditions. Yegua lignites are primarily swamp or marsh lignites. (Aquatic ferns have also been noted in Tertiary lignites in the Rhine region of Germany [20].) Organic material in Manning lignites is more finely divided and more degraded to an amorphous state than in Calvert Bluff or Yegua lignites, indicating a marshy origin of the Manning lignites [4]. Pollen of Engelhardia and Nyssa are abundant, along with occasional examples of
Pollenites laesius. Throughout the Gulf Coast the upper Jackson is marked by very abundant Engelhardia. At the end of the Eocene, Engelhardia became less common and were replaced by the more abundant oak, Quercus [4]. Gulf Coast lignites do not contain Taxodium or Liquidambar (red gum) pollen in amounts or distributions characteristic of modern peats from inland swamps of levee flanks of the Mississippi delta [4]. (Taxodium is abundant in clastic Paleocene or Lower Eocene sediments of the Gulf Coast, and occurs in Calvert Bluff lignites, but mainly in association with clay partings.) Swamp-derived lignites of the Gulf Coast region show palynomorphs of both Engelhardia and
Nyssapollenites, as well as other triporate pollen from deciduous hardwoods [21]. Cypress pollen has not been found in any of the Wilcox, Claiborne, or Jackson lignites, but such pollen abounds in modern sediments of the Mississippi delta. Herbaceous plants in the marsh environment included the Carex, Arecipites, Calamuspollenites, and Liliacidites [21]. 2.3 E N V I R O N M E N T S OF DEPOSITION
This section discusses the major types of depositional environments in which plant debris accumulated and eventually transformed to lignite. The paleoflora that contributed to the major lignite deposits have been introduced; the section that follows will describe some of the chemical pathways of coalification in the conversion of accumulated plant matter to lignite. The subsections
55 below are arranged by the major types of depositional environments. There is, however, some inevitable overlap in the classification of these environments; for example, a swamp existing on a delta might be interpreted as a deltaic or a swampy environment. Furthermore, in some instances differing interpretations have been advanced for the depositional environment of a particular lignite. 2.3.1 Fluvial environments Fluvial lignite is characterized by a high percentage of woody material, low sulfur content, and palynoflora typical of a forested, fresh-water swamp [22]. For example, pyritic sulfur contents of 0.03--0.50% reported for some Wilcox, Jackson, and Yegua lignites [11] are consistent with fresh-water peats [23]. Tree stumps and trunks 6 m long have been observed in fluvial Texas lignites [24]. The commercial deposits of Texas lignite formed as backswamp peat deposits on broad floodplains [22]. Fluvial or fluvial-dominated deltaic environments are typical lignite facies of East Texas [25]. Fluvial lignite in east-central Texas is found between the Colorado and Trinity rivers in the lower Calvert Bluff Formation of the Wilcox Group (Lower Eocene). About three-fourths of the lignite resources in Texas are fluvial [25]; the commercial deposits tend to occur in areas between paleochannels. Layered sequences that result from cycles of fluvial sedimentation characterize the deposition pattern. The layers tend to be thicker at the bottom of the sequence and become thinner as one moves up the sequence. Thick beds of lignite in the Upper Wilcox (> 1.5 m) occur between fluvial channel sand belts [26]. These lignites cap crevasse splays that are 9 to 12 m thick and coarsen upward. The peat deposits accumulating in Borneo between dendritic stream courses may be a modern analogue of the East Texas Wilcox lignite depositional environments [3]. Interpretations of the deposition of the Yegua lignites suggest a wave-dominated delta [27] or a fluvial-dominated system [28]. Both interpretations suggest that the lignite deposited in interchannel positions [27], accumulating in hardwood swamps, and that the original peat accumulated in a fluvial environment on an ancient coastal deltaic plain. Thin marine deposits, glauconitic sands, marls, or muds separate the thick lignite-bearing units [27]. Compared to the lignites in the northeast, accumulation in east-central Texas was lower on the coastal plain and the deposit was consequently subjected to greater marine influence. This accounts for the higher sulfur contents of the east-central lignites compared to those of the northeast. (Other factors causing a difference in sulfur contents may have been higher temperatures resulting from deeper burial, or a slower rate of accumulation [25].) The Calvert Bluff and Yegua lignites were deposited in a fluvial-deltaic system [11,29]. The palynology of the Calvert Bluff suggests primary accumulation in hardwood swamp environments, and to a lesser extent in marshes [4,27,30-32]. The Mississippi delta system is a modem analogue for the Calvert Bluff depositional environment [27,33,34]. The relationship between swamps and marshes to channels on the delta is similar to the Calvert Bluff lignite and its associated channel facies. The A tchafalaya and Des Allemands-Barataria basins are modern analogues of the interchannel basins in the Calvert Bluff [17,27,35]. The Des Allemands-Barataria
56 Basin is part of the fluvial-deltaic complex of the Mississippi, shallow with low relief, broadening and opening to the south. The Des Allemands-Barataria Basin lies between levee and meanderbelt deposits and an older, abandoned course of the Mississippi. The basin contains a distinct zonation which includes, proceeding coastward, a cypress-gum swamp, freshwater marsh, saline marsh, and interconnected lake system. Moving toward the Gulf, the number of basins increases but their size diminishes. Modem peat deposits in the Mississippi delta are thickest and most extensive where the alluvial and delta plains meet. The Calvert Bluff lies just above the Simsboro Sand. The lignite shows no relationship to the underlying sand; however, the sand was the platform for accumulation of the lower Calvert Bluff lignites, as well as being a fresh-water conduit and aquifer
[25]. Wilcox Group lignites in the Sabine Uplift area were deposited by rivers flowing southwesterly from the Ouachita Mountains [36]. These lignites are divided into two informal units: the Upper Wilcox, an aggradational, fluvial unit, overlying the Lower Wilcox progradational, deltaic unit. Lower Wilcox lignites of Texas extend eastward into Louisiana. These lignites formed in a very large interdeltaic area which itself formed as fluvial sedimentation moved both to the east and west of the Sabine Uplift [36]. Abundant kaolinite and quartz, with minor amounts of dickite, suggest a fresh water fluvial environment of deposition for the Chemard Lake lignite (Louisiana) [19]. Taxodium and Thomsonipollis palynomorphs also indicate a fluvial environment between a lower fluvial plain and an upper delta plain. Upper Wilcox lignites are found in small floodbasins between sand belts filling fluvial channels in large alluvial floodplains, analogous to the modern Des Allemands-Barataria Basin. In the Wilcox Mount Pleasant Fluvial System on the Texas-Louisiana border the environment was one of greatly meandering fresh water streams, and peat was deposited in, or adjacent to, abandoned stream channels, along stream terraces, or between overbank deposits. South and east from this region (i.e., toward the sea) peat also accumulated in the Rockdale delta system, which was characterized by marsh distributary channels. Wilcox lignites of Mississippi were deposited in a low-lying environment near the coast [37]. During the Eocene, the embayment area was a humid, subtropical coastal plain supporting strand and lowland swamp flora [38]. Further inland, the Appalachian foothills supported a temperate, upland forest. These lignites are characterized by small deposits of erratic seam thickness, and by multiple seams. The seams, generally of irregular shape, range from long, narrow fluvial deposits to more elliptical deposits typical of a deltaic origin. The seams may be up to 3.7 m thick, but at the margins of the deposits the thickness may be only a few centimeters [37]. Mississippi lignites deposited in an area created by southward movement of the Mississippi Embayment toward the Gulf of Mexico. Many features of the coastal plain--swamps and marshes, estuaries, landlocked bays, and lagoons--provided basins for accumulation of plant remains. These lignites occur as small, stacked deposits in contrast to large, blanket-like seams. The configurations of the ancient swamps, bays, and other features of the coastal plain determined the shapes of Mississippi Wilcox lignite deposits.
57 The Golden Valley Formation (Early Tertiary) in North Dakota deposited in a fluvial environment [2]. The existence of sandstone lenses typical of channel facies, interbedded with deposits typical of backswamp or overbank conditions, provides the basis for this deduction [2]. The Fort Union Group in southwestern North Dakota consists of deltaic (the Slope and Ludlow Formations) and marine (the Cannonball Formation) deposits overlain by alluvial plain deposits (the Bullion Creek and Sentinel Butte Formations). The lower Sentinel Butte in the Knife River area of west central North Dakota was deposited in swamp and fluvio-lacustrine conditions [39]. The lignite was deposited in the swamp environments and the elastic sediments in the fluviolacustrine conditions. These two systems alternately dominated an alluvial plain that drained to the east and southeast toward the Cannonball Sea. The continuity of the lignite suggests that similar environmental conditions prevailed across wide areas of the Williston Basin during the time of deposition. The thickness of the lignites shows that the environmental conditions prevailed for long periods of time. The times required for deposition were about 4,500 years for lignite 1 m thick to 14,000 years for 3 m thick seams [39]. An alluvial flood plain depositional model has been proposed to fit the Tongue River and Sentinel Butte [40]. The sand beds represent channel fills or deposits formed by migration of the channels. Sandy and clayey silt beds deposited as natural stream levees, while other clays and silts deposited in back basin areas of the flood plain. Because the lignite beds in the Bullion Creek and Sentinel Butte are relatively thick and laterally continuous for long distances, there must have been lengthy periods of fairly uniform conditions in the late Paleocene in North Dakota. The environment of deposition was similar to the modern Mississippi River delta [41]. Tongue River lignites were deposited by eastward-flowing, sluggish streams draining a source area to the west [42]. A stable fluvial system allowed development of protected back-swamps. As this depositional episode ended, elevation of the source area was reduced to the extent that the rate of subsidence exceeded the rate of sedimentation. Swampy conditions then became widespread throughout western North Dakota. Here the lignite beds are thin without extensive lateral persistence. The proximity of the lignite to other sediments of clearly fluvial origin strongly indicates that the lignites were deposited in fluvial conditions. These lignites are generally high in moisture and ash. In central and eastern Montana, and adjoining areas of the Dakotas and Wyoming, a broad, low-lying coastal plain existed during the Cretaceous and Early Tertiary. Extensive peat swamps formed on the plain. The peat beds were subjected to recurrent burial by sediments spreading out from the uplifting of the Rocky Mountains. Continual repetition of this process resulted in numerous buried beds of peat that eventually became beds of lignite. For example, near Roundup twenty-six beds of coal have been identified [43]. Moose River Basin (Ontario) lignite was deposited in a floodplain environment [44]. Freshwater alluvial floodplain deposition of this lignite is reflected in its syngenetic mineral content; the primary clays are kaolinite and illite, and pyrite is less common than in coals deposited in marine or marine-influenced environments [45]. The Ravenscrag Formation in Saskatchewan is equivalent of the upper Fort Union in North
58 Dakota [46]. The lignite was deposited in an alluvial plain-fluvial environment [46]. This lignite shows significant banding, which, together with the variations in petrography, suggest the accumulation of the precursor peat in a forest moor environment. Water level variations in the swamp contributed to a diverse sequence of plant communities, which in turn resulted in a diversity in the peat. Periodic low water levels may expose the peat to air, with oxidation forming inertinite. At other times, deep water levels contributed to the accumulation of attrital material. During periods in which the water level was relatively stable, preservation of woody plant parts was favored. These combined effects lead to formation of a banded lignite seam with a variety of macerals [46]. Coal of the Tintina Trench in the Canadian Arctic was deposited in fluvial and lacustrine environments [47]. No influence of marine sources is apparent. Sub-environments included lakes, alluvial fans, fan deltas, braided and meandering streams, and associated flood plain environments [47]. Variations in the sedimentary loading, and particularly variations in the geothermal gradient, complicated the coalification processes. The geothermal gradient was abnormally high during much of the burial period, a result of the emplacement of shallow magmatic intrusions. Coals of the Tintina Trench display the highest rank gradients--0.1 to 0.2% Ro/100 m - - o f any coals of western Canada [47]. A further complication of the stratigraphic pattern is strike-slip faulting, which has juxtaposed areas of different thermal histories. The Alaskan lignites and subbituminous coals in the Beluga, Nenana, and Yentra coal fields formed in various environments, including alluvial plains of non-marine continental-fluvial systems, and forest moor backswamp environments on valley flats [48]. Peats formed mainly from tree vegetation. As in the case of the Saskatchewan lignites [46], drier conditions led to coals with higher amounts of inertinites [48]. 2.3.2 Deltaic environments Upper deltaic plain coals were deposited in swamps, and formed mainly from the arborescent plants growing in the region [49]. As a result, large amounts of massive vitrinite formed, with lesser amounts of cutinite, inertinite, resinite, and sporinite. In comparison, vegetation characterizing bay or estuarine facies is generally less arborescent [49]. Abundant amounts of amorphinite, as well as framboidal pyrite, reflect a significant contribution of microbial action to degradation of the plant remains. Deltaic lignite probably originated in marshes. Although deltaic lignite is non-woody (particularly in comparison with fluvial lignite), woody material occurs with some deltaic lignites. The Alcoa seam (Milam County, Texas) palynology suggests an alternation of flesh-water marsh and hardwood swamp environments. Deltaic Wilcox lignites are characterized by low ash, moderate sulfur content, and a wide lateral extent, consistent with original deposition as a blanket peat, that is, peat which formed on inactive delta lobes [50]. Wave-dominated deltaic facies are characteristic of the Eocene lignites of South Texas [25,51]. A modern analogue is found in Malaysia, in the delta of the Klang and Langat rivers.
59 Deltaic lignite is found in the Wilcox in Central Texas and in the Yegua and Manning formations in the southeast. Three types of sedimentation patterns have been identified in deltaic lignite: sedimentation alternating between distributary channels and interchannel areas, repetitive delta front sequences, and meanderbelt deposits [22]. Commercially important deltaic lignites occur with interdistributary deposits in delta plains. East Texas deltaic lignite occurs in the Jackson Group between the Colorado and Angelina Rivers [22]. Jackson Group lignite in Southeast Texas also accumulated in deltaic environments, originating from blanket peats that spread across abandoned distributary channels in lower delta plain environments [27]. Lignite in the Manning and upper Wellborn Formations accumulated in either swamps or marshes [4,52]. Laterally extensive and relatively thick lignites derive from blanket peats originating in a variety of inactive environments from distributory channel fills to bay or lake fills [25]. Lignites that are more restricted areally may have accumulated in interdistributary basins while deltation was active [25]. 2.3.3 Lagoonal environments Lagoonal lignite is characterized by high sulfur contents and high ash values. These characteristics suggest an origin in a salt marsh that experienced frequent introduction of clastics [22]. Deposits of lagoonal lignite in Texas occur mainly in the Wilcox and Jackson Groups and Yegua Formation in the south, and in the Wilcox in East Texas. The sedimentation pattern coarsens upward; lignites are associated with lagoonal muds. Lagoonal lignite occurs in South Texas in the Jackson Group south of the Atascosa River [25]. Lignite occurrences are elongate, extending in a belt roughly 16 to 24 km wide and 200 km long [25]. South of the Atascosa River, Jackson lignite is strandplain or lagoonal [25]. Modem analogues of this system occur in western Mexico, along the Nayarit coast. There the peats are accumulating in a strandplain-lagoonal system in which peat is being laid down on top of a strandplain-barrier bar clastic sediment [53]. The resulting stratigraphic sequence of clastics topped by peat is similar to sequences that can be recognized in the lower Jackson [25]. 2.3.4 Backswamp environments Martin Lake (Texas) lignite was deposited in an arboreal (Nyssa) swamp, as indicated by high ulminite and terrestrially derived exinites [54]. Areas in the Martin Lake seam that show high inertinite contents indicate regions where the peat swamp was drying. Darco (Texas) lignite formed from backswamp peats on flood plains that were separated by meander belts [22]. The depositional environment was a forested, fresh-water swamp, inferred on the basis of a low sulfur content [22], woody appearance, and accumulated palynoflora [55]. Chemard Lake lignite is the product of upper deltaic arborescent flora that accumulated in a fresh-water swamp [56]. The forest vegetation is indicated by bright, banded, and banded-bright lithotypes. Clarains are the dominant lithotypes with clarite-V and vitrite the dominant
60 microlithotypes [19]. These lithotypes contain significant amounts of pollen of Carya and
Triporopollenites bituitus. Dull macerals such as duroclarite and carbominerite occur in association with the floral assemblage containing higher amounts of Engelhardia and Microreticulatosporites [19]. The vitrinite (60.8% average, moisture-and-ash-free (maf) basis) and inertinite (12.9% average, maf basis) contents also indicate an origin from woody vegetation. This lignite has a low content of pyrite, an indication of deposition in a fresh-water environment. Some clarite bands contain high pyrite, indicative of a marine transgression that covered parts of the peat [57]. Chemard Lake lignite palynology suggests an upper deltaic interdistributary environment [57]. The lignite is dominated by arborescent paleovegetation that accumulated in a fresh-water swamp on the upper deltaic plain [ 19]; the lignite contains minor amounts of hardwood pollen grains. Lignite in the Knife River Basin of North Dakota formed in swamps in the vicinity of the Cannonball Sea, which was in retreat during the late Paleocene [41]. The environment of deposition of the Hagel bed, inferred from palynomorphs, was a laterally extensive, aborescentdominated swamp forest characterized by cypress trees and associated herbaceous ferns and mosses, with a minor deciduous flora [58]. The dominance of Taxodiaceae--Cupressaceae pollen indicates the swampy terrain with abundant taxodium trees. Abundant xylitic material in the lignite indicates that plant remains accumulated under standing water, and that the surface was covered by standing water for most of the year. This environment was similar floristically and physically to the present Okenfenokee Swamp [59]. The Okefenokee currently has an area of 1700 km2 depositing a thick, continuous layer of peat [60]. The Beulah-Zap (North Dakota) depositional swamp was about 1050 km2 [61]. Evidence for lacustrine deposition of the Beulah-Zap lignite includes fine-grained (clay and silt size) sediments in finely laminated underclays and partings within the lignite [62]. The fine grained, finely laminated partings represent transgression-regression sequences in a marsh-lake system. No evidence of a meandering fluvial system, such as sand deposits, peat erosion, or channel structures, exists. The rate of peat deposition in the Okefenokee is about 1 cm per 20 years [63]. The compaction ratio of peat to soft brown coal is about 2 [6]. These data applied to the Hagel seam suggest a rate of deposition of approximately 4000 yr/m [58], which is very rapid on a geological time scale. The alternation of lignite and clastic deposition also took place rapidly, probably controlled by shifting of associated lacustrine and fluvial depositional environments. Pollen grains from Falkirk lignite indicate a more upland flora and are, in part, detritus. The Falkirk also has the coarsest grained clastics of three mines (Falkirk, Center, and Glenharold) at which the Hagel was studied. Lignite of the Falkirk mine was more closely associated with fluvial environments, possibly the system that supplied water to the taxodium swamp and lake environments of the Center and Glenharold mines [58]. The Center and Glenharold mines were more likely associated with lacustrine deposition [3]. The lower sodium content of the Falkirk relative to the Center and Glenharold lignites may be due to a higher mobility of the sodium ion in the hydrologically more dynamic fluvial system [58].
61 In Montana, the Tongue River Member of the Fort Union Formation was deposited by slow-moving streams on a low gradient. Sediments were transported eastward in suspension. Near the close of the depositional event, the altitude of the sediment source to the west was reduced. As a result, the rate of subsidence exceeded that of deposition, and a swamp was created. The coal beds were deposited in this backswamp [64]. 2.3.5 Marsh environments Texas lignites in the Manning Formation (Jackson Group) accumulated in marshes on the lower delta plain of a fluvial-deltaic environment [35]. These lignites derive from blanket peats that accumulated on foundering lobes of the delta and spread into inactive environments such as lake or bay fills and distributary channels [28]. Lignites of the lower seam at the Big Brown mine and the lower and middle portions of the Sandow mine were deposited in reed marsh complexes, as indicated by high humodetrinite and liptodetrinite contents [54]. Lignite from the San Miguel mine also deposited in a reed marsh. Gelification is more pronounced than in the Big Brown or Sandow lignites, and there is greater evidence of bacterial activity, suggesting that the conditions in the marsh that produced the San Miguel lignite were at various times both oxic and anoxic [54]. Deposition of some organic material in regions of subaquatic bacterial activity is indicated by the presence of dinoflagellates and sapropelinites. The high gelinite content indicates an oxic environment, which may have derived from aqueous oxidation of peat. The presence of eugelinite indicates that the water was at times brackish. Martin Lake lignite formed in fresh or slightly brackish water. The lignite has a low sulfur content, and a sulfur isotope ratio of +9.5 [65], indicative of a freshwater or brackish environment. The coarsening-upward sequence in the overburden contains pyrite nodules and siderite bands and concretions, indicative of highly reducing, anoxic, non-sulfidic conditions in the bottom sediments, and further indicating that the pore fluid in the sediments was not sea water [66,67]. Coexistence of siderite and pyrite indicates brackish water deposition. North Dakota lignites have been suggested to have been deposited from peat bogs similar to the modern swamps of Wisconsin and Michigan [68]. Beulah-Zap lignite was deposited in a marshdominated lacustrine system [62]. The depositional basin had extremely low relief. The rates of peat accumulation and basin subsidence were in equilibrium, resulting in a thick and laterally continuous lignite free of carbonaceous shales. Beulah-Zap deposition started in moderately deep water. Vegetation growth was halted twice by major increases in the water level that also resulted in deposition of clay and silt in the southern portion of the basin. Deposition ended with a major drying episode, followed by extensive flooding that terminated peat accumulation throughout the depositional basin. The sequence of depositional conditions was deduced from the distribution and abundance of the lithotypes, using the technique of seam formation analysis [62]. The lowest seam formed in deep water, with a gradually, but steadily, shallowing water level. Deposition of the middle seam began in relatively shallow water. The water level then increased throughout the depositional basin, so that the middle portion of the middle seam formed in moderate to deep
62 water. As deposition continued, a sequence of deepening followed by shallowing occurred. The uppermost Beulah-Zap seam fluctuates in thickness and is not laterally extensive. The depositional environment was unstable, with the majority of deposition occurring in moderate to shallow water with an overall shallowing trend preceding the end of deposition. The most important coalification process in the Beulah-Zap lignite was humification, as indicated by the dominance of huminite macerals in the lignite [62]. Gelification was important in horizons overlying inorganic-rich zones or carbonaceous shales. Fusinitization was a minor process occurring mainly at the end of deposition as the shallowing water allowed periodic subaerial exposure. Good preservation of fusinite macerals suggests that more fusinitization occurred by fire than by subaerial exposure. 2.3.6 Lacustrine environments In a lacustrine setting, marshes and swamps will form along the shores of the lake [49]. Vitrinite will form in abundance from the woody parts of plants. Alginite will occur to a lesser extent than in lignites deposited at the depocenter, because algae would be the dominant source of plant material only toward the center of the lake. In lignites formed near the depocenter, alginite will be more dominant, along with amorphinite, the degradation product of alginite [49]. The Chemard Lake lignite paleoflora have been interpreted as representing peat accumulation in fresh water lakes of an upper deltaic environment [19]. The fresh water environment is indicated by spores of fresh water algae, Schizosporis texus and Schizosporis
parvus. Other vegetation indicative of a lake or swamp environment included algae, fungi, ferns, Sphagnum, and hardwood trees such as Carya and Engelhardia [ 19]. Similar assemblages have been reported for the Mount Pleasant and Rockdale Delta systems of Texas [31]. Infilling of the swamp is demonstrated by the vertical distribution of palynomorphs. Algal spores are dominant near the base of the seam. In the middle of the seam the spores of ferns and mosses are abundant. Hardwood tree pollen becomes more abundant near the top of the seam, the development of deeply rooted vegetation being consistent with a reduction of surface water. Taxodium is rare in Chemard Lake lignite. Evidence for deposition in an ancient oxbow lake exists for Claiborne Group lignite in Tennessee [4]. Arboreal pollen is common at the base of the lignite. Herbaceous pollen becomes increasingly abundant upward. As the source of clastic sediments to the lake was cut off, the lake filled with organic debris from the surrounding area, which was wooded. However, herbaceous plants became established around the lake margins and gradually came to dominate the flora as the lake filled with organic debris. Similarly, lignites in the Jackson Purchase region of Kentucky may have formed in abandoned oxbows of Eocene rivers [ 16]. Large changes in peat thickness and paleofloral content over relatively short distances would occur in such situations, and produce significant variations in petrographic and palynological composition of the lignite.
63 2.3.7 Summary Figure 2.1, adapted from [69], summarizes some of the principal features of paleoflora, environments and depositional settings, and the resulting microscopic features of the lignites.
Paleoflora
Sequoia
Environment
Setting
Microscopic features
Lithotype
NyssaTaxodium
Swampmarsh complex
Marsh
Aquatic
Upper delta plain
Junction of upper and lower delta plain or lower delta plain
Lakes on delta plain
Mixed humotelinite (ulminite), Abundant humodetrinhumotelinite ite, lipto(mainly uldetrinite, minite), sporinite, sporinite, cutinite, resinite, and alginite, and suberinite resinite
Mainly humodetrinite and liptodetrinite with minor humotelinite alginite
Mainly humocollinite, humodetrinite, sapropelite and major alginite
Moderate to finely banded xylitic to non-xylitic coal
Unbanded non-xylitic to unbanded detrital coal
Unbanded, tough non-xylitic or detrital coal
Swamp
Alluvial plain backswamp or swamp at junction of lower alluvial plain and upper delta plain
Mainly humotelinite with textinite A, suberinite, resinite
Moderate to highly banded xylitic coal
Nyssa BetalaceaeMyricaceae flotant
Botyrococcus Schizoporis, Pediastrum Engelhardtia Degraded stem, Arecipites bark tissues, Liliacidites marsh plants
Moderately banded to unbanded non-xylitic coal
Fig. 2.1. Summary of relationships among paleoflora, depositional environment and setting, microscopic and macroscopic features of resulting coal. Adapted from [69].
2.4 TRANSFORMATION OF PLANT MATERIAL TO LIGNITE 2.4.1 Introduction Peat represents the first stage of coal formation. At some point a change in the environment results in the end of peat formation and burial of the existing peat with clay, sand, or other sediments. This point represents the transition from diagenesis, or the biochemical phase of coal
64 formation, to catagenesis, or the geochemical phase. A typical peat contains 80--90% moisture and, on a dry basis, 50--60% volatile matter and 40-50% carbon. The transition from peat to lignite is marked by reduction in moisture content and volatile matter and by an increase in carbon content. North Dakota lignite contains about 35% moisture and, on a dry basis, 45% volatile matter and 70% carbon. These changes are accompanied by an increased calorific value, from 16-21 MJ/kg (dry basis) for peat up to 28 MJ/kg (dry) for North Dakota lignite [ 18]. Pollen metamorphism in lignites suggests that temperature is the primary factor in coalification, and that pressure may retard coalification [73]. At slow heating rates lignites begin to evolve volatiles at temperatures as low as 200~ [74], indicating that lignites could not have been exposed to temperatures higher than this during coalification. Hydrocarbons evolved from lignites on controlled pyrolysis reflect the geochemical origin of the coal. Sapropelic lignites from the Wilcox, Claiborne, and Jackson Groups have a bimodal nalkane distribution with domination by n-alkanes >C 25, whereas humic lignites show n-alkanes
65 gelification, indicating that gelification progresses from the outer part of the log toward the interior. Cellulose, mineral matter filling cell cavities, or other cell inclusions all retard the development of homogeneity, thus impeding gelification. At least three stages of coalification occur as wood is transformed to bituminous coal [70,71]. In the first stage, cellulose is hydrolyzed and lost from the wood, whereas the more resistant lignin is retained and concentrated. Lignin residues subsequently change to lignitic coalified wood in the second stage. During this stage, the oxygen content remains relatively constant while the hydrogen content drops. A compensating increase in the carbon content accompanies the reduction in hydrogen. The principal chemical changes in the second stage are loss of water and methoxyl groups, and loss of C3 side chains from aromatic rings in lignin. The third stage represents an upranking of the coalified wood beyond the lignite rank to subbituminous and bituminous ranks. Coalification of organic matter to form lignites is principally a loss of functional groups and condensation of small molecular units into larger ones [79]. The aromatic portion of lignite derives from the lignin of vascular plants [71]. 2.4.2 Loss of cellulose The first stage of microbial degradation of wood is the loss of cellulose; the lignin-derived structures are preserved during this stage [72,80-82]. Cellulose is inferred not to exist in lignite [83]. Solid state nuclear magnetic resonance (NMR) and pyrolysis/gas chromatography/mass spectrometry (Py-GC-MS) both show that peat and degraded wood have lost most of the cellulosic material but have retained lignin fairly intact [84]. Thus cellulose has, at best, a minor role in coalification. NMR and infrared (IR) spectroscopy of wood samples buried for various lengths of time, including some as old as Eocene age, show that lignin was preserved while cellulose was degraded and lost [85]. Birefringence of huminitic materials, an indicator of the presence of crystalline cellulose, drops rapidly during peatification and the early stages of coalification [86]. Buffed logs coalified to lignite rank have lost essentially all the cellulosic components [78]. Cellulose is not present to an appreciable extent in coalified xylem tissue, even of brown coal rank. Cellulose or thermally altered cellulose produces m-hydroxybenzoic acid (1), a compound not produced from the oxidation of substances derived from lignin, upon alkaline copper(II) oxide oxidation. Wyoming lignite and Soya (Japanese) lignite gave conversions of 43-47% to products soluble in organic solvents; m-hydroxybenzoic acid was not found [87]. The products did include p-hydroxybenzoic acid (2), vanillic acid (3), and various hydroxybenzene polycarboxylic acids and benzenepolycarboxylic acids characteristic of the oxidation products of softwood lignin. Cellulose has been isolated from early Tertiary lignites; however, this isolated cellulose is about one-tenth the molecular size of modern cellulose [76]. An argument of the importance of cellulose as a precursor to oxygen functional groups has been made for New Zealand lignites, on the basis of 180/160 isotope ratio measurements [88]. These lignites are considerably younger (Upper Eocene) than most North American lignites. The isotope ratios for lignite components were compared with compounds extracted from peat and modern wood.
66 COOH
COOH
~ , O H
COOH
(
OCH3 OH
1
2
OH
3
Sporopollenin reacts at 1500C in the presence of clays to produce a synthetic sporinite that has a 13C NMR spectrum similar to that of sporinite from North Dakota lignite [89]. NMR spectra show a reduction in aliphatic C-O groups with a simultaneous increase in unsaturated carbon (at 110-155 ppm). Structural similarities between the synthetic and the authentic sporinite, as well as similar behavior of the two materials in oxidation and pyrolysis reactions, show that carbohydrates and other easily hydrolyzable material in the original spores was eliminated during diagenesis. Microbial degradation was the major pathway for the elimination of these geochemically labile materials; chemical reactions played a minor role. 2.4.3 Structural evolution of lignin residues Huminitic materials derived from cell walls are predominately modified lignin with essentially no contribution from carbohydrates [90]. The characteristic thermal behavior of lignin is present in thermograms of lignite, but is much less pronounced in those of bituminous coals and is absent from anthracite thermograms [91], suggesting that the structure of lignite resembles that of lignin. The lignified fiber-tracheid and fiber cell walls vitrinize in the early stages of coalification [92]. After loss of the cellulosic components, significant structural changes must then ensue as the preserved lignin eventually coalifies to lignite. These changes can be inferred, at least broadly, by recognizing that the atomic H/C ratio drops from 1.2 in lignin to 0.8 in lignite, while the corresponding change in the atomic O/C ratio is 0.45 to 0.19 [ 15]. Thus lignin is not preserved intact; rather, loss of methoxyl and some C3 side chains occurs [85]. IR analyses of samples beginning with lignin and proceeding through the various ranks of coal have shown a consistent disappearance of bands in the region of 1265-1290 cm-1 [83]. The bands in this region are from the principal oxygen-containing structures in lignin. Xylem tissue still retains large amounts of lignin on coalification to brown coal rank, although modification of the lignin structures begins to occur. Lignin becomes converted to humic acids while cellulose disappears [93]. Py-GC-MS of lignitic wood shows the presence of guaiacol (4), 4-methylguaiacol (5), and
trans-isoeugenol (6), which are lignin-derived and which are also observed in modem buried woods [84]. Pyrolysis-GC of coalified logs [94] also produces methoxyphenols, such as 4vinylguaiacol (7), in addition to the compounds previously named [84]. Eugenol (8) and isoeugenol in lignitic wood indicate that lignin has survived the coalification process reasonably
67
]~Y OH '-
OH
OH OCH
jOCH3
CH : C H C H 3
CH 3
OH
y
OCH
OH CH3
CH :CH 2
<
OCH3
C H 2C H --CH 2
intact, and in particular that the characteristic propyl side chain has been preserved. Py-GC-MS of lignite collected from a clay pit of Pleistocene age (Long Island, New York) showed as major products 4, 5, 7, 4-ethylguaiacol (9), 8, cis-isoeugenol, t6, vanillin (10), and acetoguaiacone (11) [95]. These compounds derive from lignin or partially altered lignin. Eugenol and isoeugenols indicate that some lignin exists virtually unaltered in lignitic wood [84]. In particular, their presence suggests that the characteristic propyl side chain of lignin has been preserved [84]. In the Long Island clay pit lignite, the lignin is very little altered from lignin in modern wood. Compounds derived from extensively altered lignin are minor components of the total pyrolysis products. In comparison, the dominant products from a lignitic coalified wood from the Upper Cretaceous Magothy Formation (Bethel, Maryland) were phenols and cresols, rather than the methoxyphenols obtained from the Long Island lignite [95]. This difference suggests a more extensive alteration of the lignin in the Magothy lignite. Phenol, cresols, and dimethylphenols are more significant in the GC-MS traces for wood coalified to lignite rank than for brown coal xylite or degraded modern woods. Methoxyphenols account for about half the total phenols in the pyrolysis products. However, simple phenols such as phenol itself, the cresols, and the dimethylphenols are also observed. The presence of these compounds indicates that coalification eventually leads to the production of phenolic structures from the methoxyphenols [84]. Phenols and catechols amount to about 25% of the Py-GC-MS products from lignites, but comprise only about 5% of the products from degraded modern woods [15]. Phenol, cresols, and dimethylphenols identified in the F'y-GC of coalified wood are products of coalification and arise from demethylation of methoxyl groups in the original lignin. Coalification leads to the production
68 OH
OH
OH
CHECH 3
CHO
COCH 3
9
10
11
of phenolic structures that derive from the methoxyphenols (e.g., the formation of catechol-like structures from guaiacyl units). Wood coalified to subbituminous rank shows no methoxyphenols at all in the reaction products. Lignin structural changes involve reduction of the number of methoxyl groups per ring by about half, with consequent diminution of lignin pyrolysis products relative to the total pyrolysis products. The reactions represent decomposition of lignin structures by loss of methoxyl and C3 side chain groups and loss of water [96]. The concentrations of methoxyl, carboxyl, and carbonyl groups decrease as carbon content increases, even in brown coals [96]. However, hydroxyl decreases sharply at the onset of brown coal formation and then remains relatively constant until the bituminous coals form. NMR of coalified gymnosperm wood shows a progressive loss of methoxyl carbon from lignin to brown coal xylite to wood coalified to lignite rank [15,84]. The 56 ppm peak (methoxyl carbon) is small relative to that at 146 ppm (aryl carbon bonded to oxygen), indicating that methoxylated phenols are minor compared to other types of phenols. The characteristic NMR peak at 146 ppm indicates adjacent aryl oxygen structures, as in catechol or methoxyphenols. The peak ratios for the 146 ppm peak and the total aromatic carbon (100-160 ppm) show about two aryl-O carbons per aromatic ring. In this regard the lignite spectra resemble those from modem degraded wood. Thus the proportion of aromatic carbons that have an attached oxygen atom (two aryl carbon-oxygen bonds per aromatic ring, i.e., about one-third of the total aromatic carbon) does not change in conversion of degraded wood to lignite, even though methoxyl carbon does decrease [84]. Loss of methoxyl carbon but retention of aryl oxygen indicates demethylation reactions, rather than demethoxylation [84]. The aromatic structures that result from demethylation are like catechols, linked by aryl ethers as in lignin. Loss of CH3- rather than C H 3 0 - forms the catechollike structures in the lignite. 2.4.4 Evolution of the carbon skeleton In lignites the carbon structure experiences aromatization (e.g., of terpenoids), loss of functional groups, and increasing condensation as coalification proceeds [79]. Benzenoid hydrocarbon structures may derive from aromatic amino acids such as phenylalanine (12) and tyrosine (13), known to be present in recent sediments; other sources of benzenoid hydrocarbons
69
~
-'-CH2~HCOOH
HO~CHz~HCOOH NH2
NH 2
12
13
may be among the families of coumarins, flavones, and anthrocyanins [76]. These compounds thermally degrade to aromatic hydrocarbons which are still reactive under the prevailing thermal conditions and may then polymerize. Pyrolysis/mass spectrometry of lignites shows that retene (14) is a characteristic biomarker for the Northern Great Plains lignites, and an unidentified compound having mass/charge ratio of 194 is characteristic of the Gulf province lignites [97].
14
In both lignin and decomposed modem wood half of the aromatic carbons are protonated (that is, three of the six carbons in an aromatic ring), but in lignite the fraction of protonated aromatic carbons drops to 0.37, suggesting that in the lignite only two of the six aromatic carbons are protonated [98]. With no change in the extent of oxygen substitution during the conversion of lignin to lignite, the reduction in the number of Car-H bonds can only be effected by increasing the amount of Car-C bonds. NMR evidence also indicates that further ring substitution at the C-2, C5, or C-6 positions accompanies the demethylation [15]. Increased ring substitution arises from condensation of guaiacyl units. The position of the aryl carbon-oxygen peak remains nearly constant at 146-148 ppm [15], indicating that the two oxygens on the ring remain adjacent throughout demethylation and condensation. The 1515 cm-1 band in the IR spectra of lignin, wood, peat, and brown coal is weak in a lignite spectrum and absent from the spectra of higher rank coals [99]. This band is also absent from the spectra of polycyclic aromatic hydrocarbons and coal tar pitches. The increasing condensation of the single aromatic rings typical of the lignin structure into polycyclic aromatic systems in the transition from brown coal to lignite and then to higher rank coals can be followed by infrared spectral changes. In early catagenesis, lignin-like structures experience an increase in crosslinking and condensation of smaller molecular fragments into larger ones [100]. The reactions that occur include dealkylation [100], demethylation [72,80,94,100], demethoxylation [80,100], oxidation [100], ring cleavage [100], and condensation [72,100]. These processes produce an aromatic-rich material as the major portion of
70 the macromolecular structure of lignite. Alkylation of aromatic rings, following cleavage of the 13-O4 aryl ether linkage in the lignin structure (the numbering scheme is shown as structure 15), may be more important than ring condensation to form naphthalenic moieties [98].
C~C--C
OCH 3 15
O
I
2.4.5 Transformations of oxygen functional groups After lignin in wood first loses methoxyl groups it then loses aryl ether and phenolic groups [15]. In macerals derived from lignin-like structures, ether bridges may be lost during coalification by elimination of carbon monoxide [ 100]. CO elimination results in the loss of oxygen from the bridge, leaving o n l y - C H 2 - groups in methylene bridges. In liptinite macerals the methylene bridges are present in the original organic matter as it accumulated. The single, homogeneous deposit in the Mahakam delta, Kalimantan, Indonesia contains all of the coalification stages from modern plant material through peat and lignite to bituminous coal. The transformations of oxygen functional groups have been studied by IR and 13C NMR [102]. Up to a vitrinite reflectance of 0.20% (an atomic O/C ratio of about 0.50) the principal mode of decrease of oxygen is dehydroxylation. For Ro in the range of 0.20-0.60% (corresponding O/C 0.504). 12) loss of oxygen primarily occurs via decarboxylation. The major product of alkaline silver oxide oxidation of lignin methylated with dimethyl-d6 sulfate is 3-methoxy-4-methoxy-da-benzoic acid (15), whereas oxidation of methylated Beulah lignite produces large amounts of the 3,4-dimethoxy-d6-benzoic acid (16) [57]. Phenol polycarboxylic acids and benzene polycarboxylic acids produced in significant amounts from lignite oxidation are found in low to negligible concentrations among the oxidation products of lignin. The phenolic structural framework of lignin is altered early in the coalification process. Dehydroxylation of phenolic structures in lignin to benzene, naphthalene, or tetralin structures in lignite may occur by hydrogen transfer between the lignin and terpenoids, catalyzed by clay minerals. For example, the reaction of poly(p-hydroxystyrene) with d-limonene (17) in the presence of montmorillonite produces alkyl benzenes, alkyl phenols, and p-cymene (18) as products [57]. Dehydration also occurs during coalification of peat through brown coal to lignite. Consideration of coals and coal precursors as a C-H-O ternary system allows the plotting of reaction trajectories on an appropriate ternary diagram [103]. Extrapolation of reaction trajectories
71 COOH
COOH
CH 3
CH 3
) OCH 3
OCD3
OCD 3
OCD 3
/C~ H3C
16
17
18
CH 2
/ CH x H3C CH 3
19
connecting peat, brown coal (Morwell, Victoria, Australia), and lignite passes almost directly through the point representing water on the hydrogen-oxygen axis, indicating that dehydration has made a significant contribution to the coalification process. Thermal degradation of sporopollenin in the presence of clays proceeds through a variety of reaction pathways, including dehydration, ether cleavage, aromatization and condensation. Oxygen is lost by dehydration, since the decrease in aliphatic C-O is accompanied by an increase in unsaturated carbon [89]. 2.4.6 Sulfur In many bituminous coals, pyrite is the dominant form of sulfur, with organic sulfur being the second largest proportion and sulfatic sulfur a minor constituent. In peat and in some lignites, organic sulfur dominates form and pyrite is minor. Potential sources of organic sulfur include sulfur-containing amino acids (in proteins) such as cysteine (20), cystine (21), glutathione (22), and thionine (23); and sulfate esters of polysaccharides. The change of the relative importance in the forms of sulfur with increasing rank suggests that pyritic sulfur increases at the expense of the organic or sulfate sulfur, or both. Formation of pyrite depends on the existence of organic sulfur in the Everglades peats [ 104], some samples of which approach lignite in terms of composition and heating value on a moisture-free basis. Much pyrite in sediments in the early diagenetic stage is the so-called framboidal pyrite, frequently found in the remains of plant tissues, growing, for example, in cell cavities. Formation of the framboidal pyrite relates to release of hydrogen sulfide from the tissues; the hydrogen sulfide in turn derives from the organic sulfur. Reduction of organic sulfates (e.g. sulfate esters of polysaccharides) by bacteria such as
Desulfovibrio generates hydrosulfide ions or organic sulfides. These species react with iron(II) ions to form pyrite. Iron(II) sulfide has a concentration two to three orders of magnitude less than that of pyritic sulfur, and does not show variations in depth comparable to those observed for either sulfatic sulfur or pyritic sulfur. Formation of iron(II) sulfide is not important in the production of pyrite, which may form by direct reaction of reduced sulfur forms with the iron(II) ion. (These observations do not necessarily rule out the possible role of iron(II) sulfide as a transitory intermediate.) Pyrite formation in organic-rich swamps develops from the use of organic
72 NH2 i HSCH 2CHCOOH
20
NH 2 NH 2 I i HOOCCHCH2--S ~ S ~ C H 2CHCOOH
21
COOH CH2SH ] I HzNCHCHzCH2CONHCHCONHCHzCOOH H2N
22
23
oxysulfur compounds in the respiration processes of sulfur-reducing bacteria [ 104]. Reduced sulfur species such as methanethiol and hydrogen sulfide correlate with the Wildcat (Texas) lignites that were deposited in marine lagoonal environments, while oxidized sulfur products such as sulfur dioxide and carbon disulfide correlate with Montana lignites, which had no evident marine influence during deposition [97]. Oxidized sulfur compounds of the Montana lignite may correlate with the high inertinite content of the samples analyzed. 2.4.7 Accumulation of metal ions The sorption behavior of cations on Enderlin (North Dakota) leonardite was very similar to the sorption of cations on fulvic acids extracted from a podzol [ 105]. Fe+3 had the highest sorption (56 meq/100 g); sorption capacities decreased in the order Cu+2 > Al+3 > Zn+2 > Mn+2, with the sorption of Mn+2 being 35 meq/100 g [105]. Extraction of the leonardite after sorption of these cations, using water, hydrochloric acid, or ammonium acetate solution showed that Fe+3 was the most tightly bound, followed the order Al+3 > Cu+2 > Zn+2 > Mn+2. Extraction with ethylenediaminetetraacetic acid (EDTA) removed about 50% of each cation, suggesting that the strength of bonding to sites in the leonardite about equals that of the bonding of cations to EDTA. Since EDTA is a strong chelating agent, these ions, once sorbed, are fairly tightly held in the leonardite. Although leonardite is a weathering product of lignite, the similarity of leonardite behavior to that of fulvic acids in soils suggests that a similar sorption of cations from ground water into organic matter undergoing diagenesis may be responsible for the incorporation of some of these metals into lignite. Spanish lignites provide insights into the mechanisms of accumulation of heavy metal cations [106]. The adsorption of Sr, Pb, U, and Th was studied by measuring the adsorption isotherms of these ions from aqueous solutions of their nitrates onto lignite samples. The adsorption behavior was described in terms of the Langmuir equation
73 N = Noac/(l+ac) where N is the concentration of the metal in the lignite, c the equilibrium concentration of the metal in the aqueous phase, and a the ratio of adsorption and desorption constants. No is the saturation capacity. The slope of the tangent of the isotherm at low concentrations, Noa, is the geochemical enrichment factor (GEF) and, for very low concentrations, represents the equilibrium ratio of the metal in the solution and the lignite. The saturation capacity ranged from 0.18 for thorium to 1.82 for lead, and the GEF values, 65 for strontium to 6270 for lead [106]. The saturation capacities of these lignites increase with the humic acid contents. The metal retention ability of the humic acids isolated from the lignites (by sodium hydroxide extraction [ 106]) increases with pH and atomic weight and valence of the metal. The humic acids can act to concentrate heavy metal ions in the lignite. Low-rank coals are much more effective at extracting uranium from aqueous solutions than are high rank coals [107]. With Estevan (Saskatchewan) lignite contacted with an aqueous solution of uranyl sulfate, U02804, (155 ppm U, pH 2.65), the uranium content dropped to less than 2 ppm in 24 hours [108]. Tests of vitrinite-rich and fusinite-rich samples show that petrographic composition is only a secondary effect in the ability of the lignite to sorb uranium. For example, the uranium content of the vitrinite-rich sample before the experiment was 2 ppm, while after the experiment the uranium content had increased to 2031 ppm [ 108]. Comparable data for the fusiniterich sample are, respectively, 2 and 2288 ppm [ 108]. Contacting the uranyl sulfate solution with the fusinite-rich sample resulted in a higher pH of the solution at the end of the experiment than did the vitrinite-rich sample. The greater increase in pH may be an effect of leaching alkalies from the relatively more inorganic-rich fusinite. An increase in the pH of uranium solutions precipitates hydrous uranium oxides. The petrographic composition of the lignite may affect the pH of the solution or groundwater in contact with the lignite, and pH in turn affects uranium precipitation. A positive correlation was found between the ash content of Hagel bed lignite and several palynomorphs of detrital origin [ 109]. Hydrogeochemical removal of calcium by dissolution of carbonates from the overburden helped concentrate calcium in the central parts of lignite seams in North Dakota, and also increased the Ca/Na ratio in the upper portions of the seams [ 110]. Oxidation and reduction processes are also influenced by groundwater. The development of pyrite in fractures in the lignite seam, followed by the growth of gypsum crystals on the surface of the pyrite, indicates that the groundwater transported iron and sulfur under reducing conditions, and at a later time transported calcium under oxidizing conditions [ 110]. Chapter 5 provides some additional information on the accumulation of metals in lignites, primarily from the point of view of the influence of accumulation on the observed concentrations of metallic elements in lignites.
74 REFERENCES
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
R.A, Mott, Coal Assessment, The Institute of Fuel, London, 1947. L.J. Hickey, Stratigraphy and paleobotany of the Golden Valley Formation (early Tertiary) of western North Dakota, Geol. Soc. Amer. Memoir 150, (1977). E.N. Steadman, Palynology of the Hagel lignite bed and associated strata, Sentinel Butte Formation (Paleocene) in central North Dakota, M.A. Thesis, University of North Dakota, Grand Forks, ND, 1985. W.C. Elsik, Palynology of Gulf Coast lignites: the stratigraphic framework and depositional environments, in: W.R. Kaiser (Ed.), Proceedings, Gulf Coast Lignite Conference: Geology, Utilization, and Environmental Aspects, Univ. Texas Bur. Econ. Geol. Rept. Invest. 90, (1978), pp. 21-32. F.J. Rich and W. Spackman, Modern and ancient pollen sedimentation around tree islands in the Okefenokee swamp, Palynology, 3 (1979) 219. E. Stach, G.H. Taylor, M.T. Mackowsky, D. Chandra, M. TeichmUller, and R. TeichmUller, Coal Petrology, Gebruder Borntragger, Berlin, 1982. G.O.W. Kremp, R.C. Neavel, and J.S. Starbuck, Coal types--a function of swamp environment, in: Proceedings, 3rd Conference on Origin and Constitution of Coal, Nova Scotia Dept. Mines, 1956, pp. 270-286. J.E. Gerhard, Paleocene miospores from the Slim Buttes area, Harding County, South Dakota, M.S. Thesis, The Pennsylvania State University, University Park, PA, 1958. J.D. Campbell, Three-dimensional systematics of Alberta plains coal, Proceedings, 1983 International Conference on Coal Science, pp. 369-372. E.S. Moore, Coal, Wiley, New York, 1922. W.H. Calkins and W. Spackman, Tracing the origins of polymethylene moieties in coal, Int. J. Coal Geol., 6 (1986) 1-19. W.C. Elsik, Characteristic Eocene palynomorphs in the Gulf Coast, U.S.A., Paleontographica, 149(b) (1974) 90-111. W.W. Fairchild and W.C. Elsik, Characteristic palynomorphs of the lower Tertiary in the Gulf Coast, Paleontographica, 128(b) (1969) 81-89. N.O. Frederiksen, Sporomorphs from the Jackson group (upper Eocene) and adjacent strata of Mississippi and western Alabama, U.S. Geol. Surv. Prof. Paper 1084, (1980). P.G. Hatcher, Dipolar-dephasing 13C NMR studies of decomposed wood and coalified xylem tissue: evidence for chemical structural changes associated with defunctionalization of lignin structural units during coalification, Energy Fuels, 2 (1988) 48-58. J.C. Hower, F.J. Rich, D.A. Williams, A.E. Bland, and F.L. Fiene, Cretaceous and Eocene lignite deposits, Jackson Purchase, Kentucky, Int. J. Coal Geol., 16 (1990) 239254. W.R. Kaiser, Calvert Bluff (Wilcox Group) sedimentation and the occurrence of lignite at Alcoa and Butler, Texas, Univ. Texas Bur. Econ. Geol. Res. Note 2, (1976). U.S. Bureau of Mines Staff, Technology of lignitic coals, U.S. Bur. Mines Info. Circ. 7692, (1954). H.H. Doney, Recent and current research on Wilcox lignite in northern Louisiana, in: R.B. Finkelman and D.J. Casagrande (Eds.), Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 156-186. E.K. Kempf, Aquatic ferns in the Tertiary lignites of the Rhine region and their stratigraphic significance, Deutsch. Geol. Ges. Z., 118 (1966) 161-168. W.C. Elsik, Palynological studies on Gulf Coast lignites, in: R.B. Finkelman and D.J. Casagrande (Eds.), Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 146-155. W.R. Kaiser, Texas lignite: near-surface and deep-basin resources, Univ. Texas Bur. Econ. Geol. Rept. Invest. 79, (1974). A.D. Cohen, W. Spackman, and C.P. Dolson, Occurrence and distribution of sulfur in peat-forming environments of southern Florida, Int. J. Coal Geol., 4 (1984) 73-96. E.T. Dumble, Report on the brown coal and lignite of Texas: character, formation, occurrence, and fuel uses, Texas Geol. Surv., 1892. W.R. Kaiser: Lignite depositional models, Texas Eocene: a regional approach to coal geology, in: H.H. Schobert (E0.), Proceedings, Low-Rank Coal Basic Coal Science
75 26
27 28 29 30 31 32 33
34 35
36
37 38 39 40 41 42 43 44
45 46 47
Workshop, U.S. Dept. of Energy Rept. CONF-811268, (1982), pp. 9-67. M.L. Ambrose, M.L.W. Jackson, W.R. Kaiser, and D.J. Fly, Lignite occurrence in relation to depositional facies, Eocene Wilcox group, Sabine uplift area, east Texas--regional and local comparative studies, Amer. Assoc. Pet. Geol. Bull., 68 (1984) 448. W.R. Kaiser, J.E. Johnston, and W.N. Bach, Sand-body geometry and the occurrence of lignite in the Eocene of Texas, Univ. Texas Bur. Econ. Geol. Circ. 78-4, (1978). W.R. Kaiser, W.B. Ayers Jr., and L.W. LaBile, Lignite resources in Texas, Univ. Texas Bur. Econ. Geol. Rept. Invest. 104, (1980). C.D. Henry and J.M. Basciano, Environmental geology of the Wilcox group lignite belt, east Texas, Univ. Texas Bur. Econ. Geol. Rept. Invest. 98, (1979). W.A. Atlee, W.C. Elsik, D.E. Frazier, and R.P. Zingula, Environments of deposition, Wilcox group, Texas gulf coast, Houston Geol. Soc. Field Trip Guidebook, 1968. D.J. Nichols and A. Traverse, Palynology, petrology, and depositional environments of some early Tertiary lignites in Texas, Geosc. and Man, 3 (1971) 37-48. R.W. Stanton, Applications of fluorescence microscopy in the study of the components of coal, Microbeam Anal., 17 (1982) 330-332. W.B. Ayers, Jr., Sedimentologic controls on lignite quality and mining, Sandow lignite mine, lower Calvert Bluff Formation, east-central Texas, in: R.B. Finkelman and D.J. Casagrande (Eds.), Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 40-53. W.L. Fisher, Facies characterization of Gulf Coast basin delta systems, with some Holocene analogues, Trans. Gulf Coast Assoc. Geol. Soc. 19 (1969) 239-261. W.R. Kaiser, Depositional systems in the Wilcox group (Eocene) of east-central Texas and the occurrence of lignite, in: W.R. Kaiser (Ed.), Proceedings, Gulf Coast Lignite Conference: Geology, Utilization, and Environmental Aspects, Univ. Texas Bur. Econ. Geol. Rept. Invest. 90, (1978), pp. 33-53. W.B. Ayers, Jr. and W.R. Kaiser, Regional depositional setting, resources, and quality of lignite in the Wilcox group of east Texas and the Jackson group of east and south Texas, in: R.B. Finkelman and D.J. Casagrande (Eds.), Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 69-114. D.R. Williamson, The Tertiary lignites of Mississippi, in: W.R. Kaiser (Ed.), Proceedings, Gulf Coast Lignite Conference: Geology, Utilization, and Environmental Aspects, Univ. Texas Bur. Econ. Geol. Rept. Invest. 90, (1978), pp. 54-58. J.K. Warter, Palynology of a lignite of lower Eocene (Wilcox) age from Kemper County, Mississippi, Ph.D. Dissertation, Louisiana State University, Baton Rouge, LA, 1965. D.J. Daly, G.H. Groenewold, and C.R. Schmit, Paleoenvironments of the Paleocene Sentinel Butte Formation, Knife River area, west-central North Dakota, Proc. 3rd Rocky Mt. Paleogeog. Symp., 1985, pp. 171-186. A.F. Jacob, Depositional environments of Paleocene Tongue River Formation, western North Dakota, Amer. Assoc. Petrol. Geol. Bull., 57 (1973) 1038-1052. G.H. Groenewold, L.A. Hemish, J.A. Cherry, B.W. Rehm, G.N. Meyer, L.S. Clayton, and L.M. Winczewski, Geology and geohydrology of the Knife River Basin and adjacent areas of west-central North Dakota, No. Dak. Geol. Surv. Rept. Invest. 64, (1979). C.F. Royce, Jr., A sedimentologic analysis of the Tongue River-Sentinel Butte interval (Paleocene) of the Williston Basin, western North Dakota, Sed. Geol., 4 (1970) 19-80. E.S. Perry, Montana in the geologic past, Mont. Bur. Mines Geol. Bull. 26, (1962). C.F. Try, D.G.F. Long, and C.G. Winder, Sedimentology of the lower Cretaceous Mattagami Formation, Moose River Basin, James Bay lowlands, Ontario, Canada, in: D.F. Stott and D.J. Glass (Eds.), The Mesozoic of Middle North America, Can. Soc. Pet. Geol. Mem. 9, (1984), pp. 354-359. E. Van der Flier-Keller and W.S. Fyfe, Mineralogy of lower Cretaceous coals from the Moose River Basin, Ontario, and Monkman, British Columbia, Can. Mineral. 26 (1988) 343-353. A.P. Beaton, F. Goodarzi, and J. Potter, The petrography, mineralogy, and geochemistry of a Paleocene lignite from southern Saskatchewan, Canada, Int. J. Coal Geol., 17 (1991) 117-148. J.D. Hughes and D.G.F. Long, Geology and coal resource potential of early Tertiary strata
76 48 49 50 51 52 53 54 55 56 57 58 59 60
61 62 63 64 65 66 67 68 69
along Tintina Trench, Yukon Territory, Geol. Surv. Can. Paper 79-32, (1980). R.D. Merritt, Petrology of Tertiary and Cretaceous coals of southern Alaska, Int. J. Coal Geol., 9 (1987) 129-156. J.A. Curiale and R. Lin, Tertiary deltaic and lacustrine organic facies: comparison of biomarker and kerogen distribution, Org. Geochem., 17 (1991) 785-803. W.L. Fisher and J.H. McGowen, Depositional systems in the Wilcox Group of Texas and their relationship to the occurrence of oil and gas, Trans. Gulf Coast Assoc. Geol. Socs., 17 (1967) 105-125. J.A. Breyer, Tide-dominated delta model for coal-bearing Wilcox strata in south Texas, Amer. Assoc. Petrol. Geol. Bull., 68 (1984) 457-484. N.O. Frederiksen, Middle Eocene to early Oligocene plant communities of the Gulf Coast, in: J. Gray (Ed.), Communities of the Past, Hutchinson Ross, Stroudsburg, PA, 1981, pp. 493-549. J.R. Curray, F.J. Emmel, and P.J.S. Crampton, Holocene history of a strandplain, lagoonal coast, Nayarit, Mexico, in: A.A. Castanares and F.B. Phleger (Eds.), Coastal Lagoons, Universidad Nacional Aut6noma de M6xico, 1969, pp. 63-100. P.K. Mukhopadhyay, Petrography of selected Wilcox and Jackson group lignite from the Tertiary of Texas, in: R.B. Finkelman and D.J. Casagrande (Eds.) Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 126-145. D.J. Nichols, Palynology in relation to depositional environments of lignites in the Wilcox group (E. Tertiary) in Texas, Ph.D. Dissertation, The Pennsylvania State University, University Park, PA, 1970. D.R. Williamson, Lignites of northwest Louisiana and the Dolet Hills lignite mine, in: R.B. Finkelman and D.J. Casagrande (Eds.) Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 13-28. H.L. Roland, Jr., Louisiana lignite, in: W.R. Kaiser (Ed.), Proceedings, Gulf Coast Lignite Conference: Geology, Utilization, and Environmental Aspects, Univ. Texas Bur. Econ. Geol. Rept. Invest. 90, (1978), pp. 66-78. F.R. Karner, J.P. Hurley, D.R. Kleesattel, E.N. Steadman, and C.J. Zygarlicke, Distribution of inorganics, in: G.A. Wiltsee (Ed.), Low-rank Coal Research, U.S. Dept. of Energy Rept. DOE/FE/60181-1846, (1986), pp. 15-1-15-7. F.T.C. Ting, Petrified peat from a Paleocene lignite in North Dakota, Science, 177 (1972) 165-166. A.D. Cohen, Okefenokee swamp: a low-sulfur end member of a shoreline-related depositional model for coastal plain coals, in: A.D. Cohen, D.J. Casagrande, M.J. Andrejko, and G.R. Best (Eds.), The Okefenokee Swamp, Wetlands Survey, Los Alamos, NM, 1984. A.G. Leonard, E.J. Babcock, and L.P. Dove, The lignite deposits of North Dakota, No. Dak. Geol. Surv. Bull. 4, (1925). D.R. Kleesattel, Petrology of the Beulah-Zap lignite bed, Sentinel Butte Formation (Paleocene), Mercer County, North Dakota, M.A. Thesis, University of North Dakota, Grand Forks, ND, 1985. A.D. Cohen, M.J. Andrejko, W. Spackman, and D. Corvinus, Peat deposits of the Okefenokee swamp, in: A.D. Cohen, D.J. Casagrande, M.J. Andrejko, and G.R. Best (Eds.), The Okefenokee Swamp, Wetlands Survey, LOs Alamos, NM, 1984. R.E. Matson and J.M. Pinchock, Geology of the Tongue River member, Fort Union Formation of eastem Montana, in: D.K. Murray (Ed.), Geology of Rocky Mountain Coal, Colo. Geol. Surv. Resource Set. 1, (1977), pp. 91-114. J.A. Breyer, Geology of the Martin Lake and Big Brown mines, in: R.B. Finkelman and D.J. Casagrande (Eds.) Geology of Gulf Coast Lignites, Environmental and Coal Associates, Houston, 1986, pp. 29-39. R.A. Bemer, A new geochemical classification of sedimentary environments, J. Seal. Pet., 51 (1981) 359-365. R. Matsumoto and A. Iijima, Origin and diagenetic evolution of Ca-Mg-Fe carbonates in some coal fields of Japan, Sedimentol., 28 (1981) 239-259. T. Thiessen and W. Francis, Terminology in coal research, Fuel, 8 (1929) 385-405. P.K. Mukhopodhyay, J.R. Gormly, and J.E. Zumberge, Generation of hydrocarbons from the Tertiary coals of Texas--coal as a potential source rock for liquid hydrocarbons in
77 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92
a deltaic basin? Org. Geochem., 14 (1989) 351-352. P.G. Hatcher, I.A. Breger, N. Szeverenyi, and G.E. Maciel, Nuclear magnetic resonance studies of ancient buried wood. II. Observations on the origin of coal from lignite to bituminous coal, Org. Geochem., 4 (1982) 9-18. P.G. Hatcher and I.A. Breger, Chemical structures in coal: NMR studies and a geochemical approach, Amer. Chem. Soc. Div. Fuel Chem. Preprints, 27(3-4) (1982) 172179. A. Hollerbach and H.W. Hagemann, Organic geochemical and petrological investigations into a series of coals with increasing rank, Proceedings 1981 International Conference on Coal Science, pp. 80-85. D.J. Mclntyre, Effect of experimental metamorphism on pollen in a lignite, Amer. Assoc. Strat. Palynol., 4 (1972) 111-117. J. Roberts, The origin of rank in coals, Coke and Gas, 1 (1951) 30-32. R. Hayatsu, R.E. Winans, R.G. Scott, R.L. McBeth, and L.P. Moore, Investigation of aqueous sodium dichromate oxidation for coal structural studies, Fuel, 60 (1981) 77-82. E.T. Degens, Diagenesis of organic matter, in: G. Larsen and G.V. Chilingar, Diagenesis in Sediments, Elsevier, Amsterdam, 1967, Chapter 7. E.C. Jeffery, The origin and organization of coal, Mem. Amer. Acad. Arts Sci., XV (1924) 1-62. P.G. Hatcher, L.A. Romankiw, and J.R. Evas, Gelification of wood during coalification, Proceedings 1985 International Conference on Coal Science, pp. 616-619. P.G. Hatcher, H.E. Lerch, and T.V. Verheyen, Organic geochemical studies of the transformation of gymnospermous xylem during peatification and coalification to subbituminous coal, Int. J. Coal Geol., 16 (1990) 193-196. S.A. Stout, J.J. Boon, and W. Spackman, Molecular aspects of the peatification and early coalification of angiosperm and gymnosperm woods, Geochim. Cosmochim. Acta, 52 (1988) 405-414. F. Godarzi, T. Gentzis, and P. Yiakkoupis, Petrographic characteristics and depositional environment of Greek lignites. I. Drama basin, northern Greece, J. Coal Qual., 9 (1990) 26-37. C.E. Brounimann and G.E. Maciel, 1H NMR spectra of coals of various rank, obtained by the CRAMPS technique, Org. Geochem., 14 (1989) 189-192. C. Alexanian, Contribution to knowledge on the mode of formation of coal. Conclusions based on infrared absorption. Compt. Rend. Acad. Sci., 246 (1958) 1792-1975. P.G. Hatcher, H.E. Lerch, R.K. Kotra, and T.V. Verheyen, Pyrolysis g.c.-m.s, of a series of degraded woods and coalified logs that increase in rank from peat to subbituminous coal, Fuel, 67 (1988) 1069-1075. P.G. Hatcher, I.A. Breger, G.E. Maciel, and N.M. Szeverenyi, Chemical structures in coal: geological evidence for the presence of mixed structural components, Proceedings 1983 International Conference on Coal Science, pp. 310-313. S.A. Stout and W. Spackman, Peatification and early coalification of wood as deduced by quantitative microscopic methods, Org. Geochem. 14 (1989) 285-298. R. Hayatsu, R.E. Botto, R.G. Scott, R.L. McBeth, and R.E. Winans, Evaluation of lignin and cellulose contributions to low-rank coal formation by alkaline cupric oxide oxidation, Fuel, 65 (1986) 821-826. J. Dunbar and A.T. Wilson, The use of oxygen-18/oxygen-16 ratios to study the formation and chemical origin of coal, Geochim. Cosmochim. Acta, 47 (1983) 1541-1543. R. Hayatsu, R.E. Botto, R.L. McBeth, R.G. Scott, and R.E. Winans, Chemical alteration of a biological polymer "sporopollenin" during coalification: origin, formation, and transformation of the coal maceral sporinite, Energy Fuels, 2 (1988) 843-847. S.A. Stout, W. Spackman, and J.J. Boon, Peatification and early coalification of wood as deduced by analytical pyrolysis and microscopic methods, Abstr. 4th Ann. Meeting, Soc. for Org. Petrol., 1987, pp. 32-33. I.A. Breger and W.L. Whitehead, Thermographic study of the role of lignin in coal genesis, Fuel, 30 (1951) 247-253. W. Spackman and E.S. Barghoorn, Coalification of woody tissue as deduced from a petrographic study of Brnadon lignite, in: R.H. Gould (Ed.), Coal Science, American Chemical Society, Washington, 1966, pp. 695-706.
78 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110
M. TeichmUller and R. TeichmUller, Diagenesis of coal (coalification), in: G. Larsen and G.V. Chilingar, Diagenesis in Sediments, Elsevier, Amsterdam, 1967, Chapter 8. P.G. Hatcher and H. E. Lerch, Survival of lignin-derived structural units in ancient coalified wood samples, in: H.H. Schobert (Ed.), Coal Science II, American Chemical Society, Washington, 1991, Chapter 2. P.G. Hatcher and H. E. Lerch, Survival of lignin-derived structural units in ancient coalified wood samples, Amer. Chem. Soc. Div. Fuel Chem Preprints, 34 (1989) 617621. L. Blom, L. Edelhausen, and D.W. van Krevelen, Chemical structure and properties of coal. 18. Oxygen groups in coal and related products, Fuel, 36 (1957) 135-153. H.L.C. Meuzelaar, W. Windig, and G.S. Metcalf, Numerical extraction of chemical component patterns from pyrolysis mass spectra of U.S. lignites, Amer. Chem. Soc. Div. Fuel Chem. Preprints, 30(1) (1985) 200-208. P.G. Hatcher, Chemical sructural models for coalified wood (vitrinitic) in low-rank coal, Org. Geochem., 16 (1990)959-968. J.H. Silliker and S.C. Rittenberg, Studies on the aerobic oxidation of fatty acids by bacteria. 3. The effect of 2,4-dinitrophenol on the oxidation of fatty acids by Serratia marcesceus, J. Bacteriol., 64 (1952) 197-205. R. Hayatsu, R.G. Scott, R.L. McBeth, and R.E. Winans, Lignite coal: its chemical structure and origin, Org. Coat. Plast. Chem., 43 (1980) 401-406. Y. Yun and H.L.C. Meuzelaar, Simultaneous thermogravimetric and mass spectrometric observations on vacuum pyrolysis of Argonne PCSP coals, Amer. Chem. Soc. Div. Fuel Chem. Preprints, 33 (1988) 75-79. J.P. Boudou, B. Durand, and J.L. Oudin, Diagenetic trends of a Tertiary low-rank coal series, Geochim. Cosmochim. Acta, 48 (1984) 2005-2010. J.F. Stephens, Coal as a C-H-O ternary system. I. Geochemistry, Fuel, 58 (1979) 489493. Z.S. Altschuler, M.M. Schnepfe, C.C. Silber, and F.O. Simon, Sulfur diagenesis in Everglades pear and origin of pyrite in coal, Science, 221 (1983) 221-227. A. Kollman, Trace element chemistry of leonardite and its potential effect on soil geochemistry and plant growth. Amer. Chem. Soc. Div. Fuel Chem. Preprints, 23(2) (1978) 221-225. J.V. Ibarra, J.Osacar, and J.M. Gavilan, Retention of metallic cations by lignites and humic acids, Fuel, 58 (1979) 827-830. G.R. Moore, Extraction of uranium from aqueous solution by coal and some other materials, Econ. Geol., 49 (1954) 652-658. A.R. Cameron and G. LeClair, Extraction of uranium from aqueous solution by coals of different rank and petrographic composition, Geol. Surv. Canada Rept. 74-35, (1975). J.P. Hurley, D.R. Kleesattel, and E.N. Steadman, Distribution of inorganics, University of North Dakota Energy Research Center Monthly Report, March 1985. D.K. Rindt, F.R. Karner, W. Beckering, and H.H. Schobert, Current research on the inorganic constituents in North Dakota lignites and some effects on utilization, Amer. Chem. Soc. Div. Fuel Chem. Preprints, 25(1) (1980) 210-216.
79
Chapter 3
THE ORGANIC STRUCTURE OF LIGNITES This Chapter discusses the organic structural features of lignites, beginning with the lithologic layering in lignite seams, proceeding to characteristics of lithotypes and macerals, and then to details of structure at the molecular level. This Chapter follows in part from the discussion in Section 2.4 on the coalification of plant matter. It then sets the stage for the discussion of organic reactions of lignites in Chapter 4. 3.1 P E T R O G R A P H Y OF LIGNITES 3.1.1 Lithologic Layering Early studies of northern Great Plains lignites recognized the existence of distinct layers discernable in the beds [1]. More recent work has focused on the lithologic layers, also called lithobodies, observed in the Beulah-Zap lignite (North Dakota) at the Freedom Mine [2,3]. The subdivision of the seam into distinct lithologic layers is based on megascopic characteristics: appearance of the broken surfaces in the highwall; luster; fracture and hardness; and the presence of lithologically distinct units such as thin layers of clay or silt. The pattern of layering observed in the Freedom mine persists at least into the neighboring Beulah mine, a distance of 16 km [2]. The top three layers are similar petrographically, with the fourth layer substantially different. The relationship of these petrographic differences to pyrolysis behavior is discussed in Chapter 4. Table 3.1 provides the petrographic and chemical analyses of the four lithologic layers in the Freedom mine [4]. Lithologic layering is also evident in both the Beulah and Center (North Dakota) mines (which are in the Beulah-Zap and Hagel beds, respectively). In both cases, huminite- and liptinitegroup macerals are more abundant near the base of the seam, and inertinite content is inversely related to huminite content [5]. The huminite-group macerals are more abundant in the Hagel lignite (83%) than in the Beulah-Zap (65%). Fusinite macerals, particularly semifusinite, are more abundant in the Beulah-Zap than in the Hagel bed. Lithotype abundance is the basis for classification of lithobodies in the Beulah-Zap seam at the Beulah, Indian Head, and Freedom mines; six major types are recognized on this basis [6]. This classification scheme was established on the basis of principal factor analysis and cluster analysis. The classification system is shown in Table 3.2 [6]. The lithobodies range from 5 to 85 cm in thickness [7]. As a rule, attritus-dominated lithobodies occur more frequently near the top of
80 TABLE3.1 Petrographic and chemical analyses of the lithologic layers in the Freedom mine [4]. Layer: Maceral Analysis (a) Huminite Group Ulminite Humodetrinite Gelinite Corpohuminite Liptinite Group Sporinite Cutinite Resinite Suberinite Alginite Liptodetrinite Fluorinite Bituminite Inertinite Group Fusinite Semifusinite Macrinite Sclerotinite Inertodetrinite Micrinite Minerals Pyrite Quartz Clays Proximate Analysis (b) Volatile Matter Fixed Carbon Ash Ultimate Analysis (b) Hydrogen Carbon Nitrogen Sulfur Oxygen (c) Calorific Value MJ/kg (b)
1 (Top)
2
3
4 (Bottom)
35.5 25.2 0.5 1.0
38.9 23.1 0.4 2.6
38.2 21.9 1.4 2.0
42.8 18.0 1.3 6.2
0.9 0.7 2.7 0.0 1.2 5.0 0.0 0.0
2.4 O.5 1.9 0.5 0.4 5.9 0.4 0.0
1.4 O.5 0.9 0.4 0.9 3.8 0.0 0.0
3.3 O.5 1.7 1.5 1.2 5.3 0.0 0.0
4.5 6.8 0.7 0.3 8.9 1.3
4.6 8.1 0.5 0.5 7.6 0.7
8.5 7.2 0.2 0.4 8.5 1.8
2.7 5.3 0.0 0.3 4.2 1.3
1.2 2.7 0.5
0.4 0.2 0.2
1.1 0.4 0.4
0.8 1.0 0.5
38.7 46.8 14.6
43.4 45.4 11.1
43.5 50.1 6.5
42.5 50.9 6.5
3.8 60.9 1.0 1.8 17.9 23.2
4.1 62.9 1.1 0.7 20.0 24.1
4.5 66.2 1.1 0.6 21.2 25.8
4.3 66.3 1.5 0.8 20.6 25.9
Notes: (a) percent volume, (b) moisture flee basis, (c) by difference. the lignite, whereas vitrain-dominated bodies occur more frequently in the center and near the base. Lithobody 6 has a very high ash value (32%, dry basis), and, on an maf basis, has higher volatile matter (54.8%) and oxygen (24.0%), and lower fixed carbon (45.3%), carbon (68.8%), and calorific value (25.6 MJ/kg) than the other lithobodies [6]. The proximate and ultimate analyses of the other five lithobodies are remarkably similar. For example, on an maf basis the volatile matter is 44.8--48.7%; carbon, 71.1-72.6%; and calorific value, 27.2-27.7 MJ/kg [6]. Division of the Beulah-Zap bed into ten lithobodies has also been proposed [7]. Lithologic layering in the Gascoyne mine (Harmon bed, North Dakota) but has not been
81 TABLE 3.2 Average lithotype abundance (volume percent) in Beulah-Zap lithobodies [6]. Lithobody 1) Attritus dominated, abundant fusain 2) Vitrain dominated 3) Vitrain dominated, with attritus 4) Vitrain and attritus equal 5) Attritus dominated, with vitrain 6) Attritus dominated
Fusain 19.0 1.5 3.4 6.3 3.1 0.6
Vitrain 25.O 91.5 76.0 50.7 32.3 18.0
Attritus 56.O 7.7 21.5 43.0 64.7 81.4
studied in as much detail as the Beulah-Zap bed at the Freedom mine. Five layers were identified, and were partially differentiated on the basis of fusain content [8]. The ranges of fusain are Layer 1 (bottom), 2-6%; Layer 2, 3.5-13%; Layer 3, 3.5-10%; Layer 4, 19%; and Layer 5 (top), 5.5-7.5% [8]. Fusain forms horizontal planes of weakness in lignite seams. Since horizontal fracture helps differentiate layers in the seam, a classification scheme for distinguishing layers on the basis of fusain content could be developed in the future. 3.1.2 Lithotypes Lithotypes are megascopically observable components of the lithologic layers, and are distinguished on the basis of physical characteristics. For North Dakota lignites, vitrain and fusain have been described according to the Stopes-Heerlen system, and attritus by the Thiessen-Bureau of Mines system [9]. Fusain is composed of fragmental chips and fibers. It occurs in lenses up to 2 cm thick on bedding plane surfaces [2,8,10]. Typical dimensions of fusain are 2--4 mm thickness and about 2 cm2 in area [8]. Thicker lenses may be continuous for up to 3 m [8,10]. Discontinuous fusain fragments are typically 2-5 cm in length, although one fusain horizon was traceable for 30 m [10]. Fusain displayed a characteristic extreme friability, which was responsible for many horizontal partings in the seam. Crumbling fusain in the hand produces a very fine, "dirty" powdery residue [11]. Fusain is opaque in thin sections but easily recognized by the porous structure remaining from its woody origin. Generally fusain is less important than the attritus or vitrain. Vitrain occurs as discontinuous layers within the attritus. The distinguishing characteristics of vitrain are a bright luster, smooth surface, and fractures 90 ~ to the bedding plane (i.e., bidirectional cleating); the most typical physical property was its brittleness [2,10]. A fracture pattern along two perpendicular planes produces regular, blocky fragments. Vitrain does not produce much dust on fracturing. The minimum thickness of vitrain lenses is about 5 mm, typically forming fiat lenticular bodies about 10-30 mm long [8]. The maximum horizontal extent of vitrain lenses is less than 25 cm [10]. Discontinuous lenses 5-30 mm thick are contained within a dull granular matrix [ 10]. Some vitrain lenses, usually less than half of the total vitrain, contain obvious plant structures, such as concentric growth tings. Such structures are typical of a second form of
82 vitrain, anthraxylon [ 12], which has a silky luster, conchoidal fracture, and is very hard but brittle. The anthraxylon form of vitrain often occurs in bodies of 5--50 mm thickness. A type of vitrain with a dull texture in the Beulah-Zap lignite occurred most frequently in massive attrital lithobodies and usually contained significant amounts of well-preserved plant structures. Among the Fort Union lignites, vitrain bands > 12 mm in thickness may make up more than 15% of the lignite [ 13], with a total huminite content of about 80% or more. Large vitrain lenses can be seen in the working faces of mines, where they may occur in the form of compressed tree stumps or logs of length and diameter each > 1 m [ 13]. Attritus is a collective term for layers of dull to moderately bright lignite interlaminated with vitrain and fusain lenses [10]. Attritus has characteristic granular texture [2,14]. Attritus flakes if scraped, but shows extreme resistance when struck. Attrital layers 10 cm thick can often be traced laterally for several meters [ 10]. Attritus occurs as granular massive layers of 5--40 mm thickness with dull luster, irregular fracture along horizontal planes, and some 90* cleating (though not as extensive as in vitrain) [8]. This behavior is particularly noticeable in the field, in that lithologic layers in which attritus is the major lithotype appear as bulges or protrusions from the exposed lignite face, showing fewer ~ffects of weathering and the absence of desiccation cracks. Attrital lignite breaks easily along irregular horizontal planes when struck with a hammer. Woody vitrain is much more resistant. Attrital lignites are mainly composed of plant debris, much of which was macerated or otherwise decomposed (e.g. by bacterial action), probably during the peat stage of coalification [ 15]. Most of the attritus is translucent, often with a yellowish coloration, when examined in thin section, but up to 15% may be opaque [15]. The plant debris derives from plant fibers; decayresistant reproductive parts such as pollen, spores, and seeds; and cuticles of leaves and fruit. These materials are generally translucent orange in thin section. (Completely opaque attritus has not been related to specific plant components [ 15].) Attrital lignites have a uniform grainy texture and light to dark brown coloration. They are not banded in appearance. Translucent and opaque attritus are differentiated on the basis of optical behavior in thin section [16]. Translucent attritus generally consists of pollen, spores, and leaf cuticles. Opaque attritus is amorphous or may show some cellular structure. (Fusain is also opaque and may show a woody cellular structure, but is differentiated from opaque attritus by being thicker in vertical section in the seam [ 16].) Attrital lignite originated in a swampy environment that provided for very rapid decay of plant material [15]. In such an environment, only the most decay-resistant portions of plant material could be preserved reasonably intact. Any woody tissue that would survive in this environment would be very finely macerated. Some attrital lignites may be allochthonous; that is, they accumulated in shallow water by the influx of water- or air-borne plant debris. Arkansas lignites may have accumulated in this fashion [15]. Lignites that give high yields of extractable waxes are predominantly attrital [ 15]. Woody lignites, in contrast, give low yields of waxes. Nonbanded attrital lignites having high concentrations of waxy plant debris may be "canneloid," i.e., the low-rank homolog of cannel
83 coals [ 1]. The average concentrations of the lithotypes in Beulah-Zap lignite are 35-45% vitrain, 5% fusain, and 40--60% attritus [3,17]. Attritus is more abundant directly overlying clay partings and at the base of the seam, whereas fusain was essentially absent at these locations [3,10,17]. This distribution is generally comparable to observations made on bituminous coal seams [ 18]. Vitrain occurs as discontinuous lenses less than 5 mm thick within the attritus. Lithobodies dominated by vitrain or fusain occur more frequently near the top of the seam. The horizontal variation of lithotypes in six samples from various locations in the Gascoyne mine shows vitrain ranges of 28-37%, attritus 59-66%, and fusain 2-7% [8]. The results are fairly consistent from one sampling location to another, and show no obvious trend with horizontal direction. Characteristics of the lithotypes separated from Beulah-Zap lignite are summarized in Table 3.3. The data in Table 3.3 are averages calculated from more extensive tabulations in [10]. Proximate and ultimate analyses for one set of lithotypes of Beulah lignite are given in Table 3.4 [ 19]. The petrographic analyses of the samples used to obtain the data in Table 3.4 are given in Table 3.13. TABLE 3.3 Average analyses of Beulah-Zap lithotypes (moisture-free) Vitrain Attritus Fusain Proximate (a) Volatile Matter Fixed Carbon Ash Ultimate (b) Hydrogen Carbon Nitrogen Sulfur Oxygen Calorific Value, MJ/kg (b)
48.2 45.4 6.4
46.5 45.4 8.2
39.9 45.1 15.0
4.42 64.66 0.94 0.81 22.79 25.5
4.09 64.17 1.10 0.67 21.89 24.9
3.40 58.12 0.75 0.69 20.48 22.9
(a) Based on five fusain and seventeen attritus and vitrain samples. (b) Based on four fusain and sixteen attritus and vitrain samples.
The proximate analysis of unseparated lignite agrees fairly well with a proximate analysis calculated from weighted results of the proximate analyses of the separated lithotypes. The proximate analysis of lithotypes separated from Beulah lignite, and the agreement with the reconstructed analysis of the unseparated lignite, are shown in Table 3.5 [ 13,20]. The data in Table 3.5 were obtained by thermogravimetric analysis and are shown on a moisture-free basis.
84 TABLE 3.4 Proximate and ultimate analyses of Beulah lithotypes, moisture-free basis [19]. Vitrain Proximate Volatile Matter Fixed Carbon Ash Ultimate Hydrogen Carbon Nitrogen Sulfur Ash Calorific value (MJ/kg)
Attritus
Fusain
45.9 47.5 6.6
43.9 46.5 9.6
40.3 48.4 11.3
4.70 66.93 0.81 1.05 6.6 26.1
4.01 65.14 1.03 0.76 9.6 24.8
3.85 65.30 0.92 1.61 11.3 25.1
TABLE 3.5 Proximate analyses of lithotypes and unseparated Beulah lignite [13,20].
Volatile Matter Fixed Carbon Ash
Vitrain Attritus Fusain 41 43 33 52 50 59 7 7 8
Whole Lignite Calcd.* Exptl. 42 42 51 49 7 8
*Calculated from the average of the values for the lithotypes, weighted for the amount of each li thotype in the unseparated lignite.
A compositional relationship is found among the medium dark, medium light, and dark lithotypes of Victorian brown coal [21] and attritus and fusain in Beulah-Zap lignite [2] by expressing elemental compositions on a ternary bond equivalence diagram [21,22]. The five lithotypes are related in order of decreasing quantity of cellulose (or, in other words, by increasing loss of cellulose): medium dark > medium light > dark > attritus > fusain. Further, a linear correlation (r = 0.85) exists between the aromaticity of the lignites and the carbon bond equivalence [21. The most thorough investigation of separated lithotypes has been performed with those from Beulah lignite. Some properties of hand-separated samples of lithotypes from the Beulah mine are provided in Table 3.6 [2]. Vitrain shows evidence of significant biochemical activity. The very low cellulose content suggests bacterial degradation during diagenesis. The principal ulminite maceral in the vitrain is euulminite, in which very little cell wall structure remains. The attritus is less well compacted than the vitrain, which accounts in part for its much higher relative mechanical friability. Fusain is charcoallike in appearance, indicative of an origin in bog or forest fires. The large amount of residual
85 TABLE 3.6 Characteristics of lithotypes of Beulah lignite [2]. Proper t3, Carbon, %maf Hydrogen, %maf Nitrogen, %maf Sulfur, %maf Aromaticity (fa) Cellulose, %maf Methoxy, %maf Carboxyl, meq/g maf Inorganics, % mf (a) Minerals, %mf (a) Mechanical friability, %(b) Fusinite, % Semifusinite, % Ulminite, % Humodetrinite, % Inertodetrinite, %
V i train 71.66 5.03 0.87 1.12 0.65 0.005 2.08 2.39 2.90 1.35 18.4 1 1 69 10 2
A ttri tus 72.06 4.44 1.14 0.84 0.66 0.025 0.68 2.83 4.01 3.17 36.1 2 5 31 34 10
Fusain 73.62 4.34 1.04 1.82 0.80 0.023 0.72 2.47 3.34 4.06 32.3 45 20 10 5 8
(a) follows Australian brown coal practice (e.g., [24]) (b) discussed in Chapter 7 cellulose, relative to vitrain, suggests interruption of biochemical processes by the fire. Since decarboxylation occurs readily during pyrolysis, the similarity of carboxyl contents among the lithotypes indicates that they formed by later oxidation of the coal and are not relics of the original plant material. A simplistic approach based on separation of Beulah lignite into light and dark lithotypes has produced some insights on differences between lithotypes [23]. The darker lithotype was the more aromatic (fa = 0.71) and contained fewer carboxyl groups, as estimated from X-ray photoelectron spectra. The dark lithotype also had the more pronounced 1600 cm-1 band in the Raman spectrum, indicative of a somewhat better ordered or more graphitic structure of the dark lithotype. Consistent with a higher carboxyl content, the light lithotype had a higher sodium content. The better structural ordering in the dark lithotype was due to a lack of steric effects that would be associated with the relatively bulky carboxyl groups and their sodium counterions. Six classes of lithotypes have been determined for Texas lignites, shown in Table 3.7 [25]. 3.1.3 Macerals (i) Within-seam variation. In the Beulah-Zap bed inertinite macerals are more abundant in the top-most meter of the seam [26]. Inertodetrinite, desinite, gelinite, and semifusinite concentrated near the top of the seam [27], although in some locations semifusinite is relatively constant throughout the seam [17]. The dominant inertinite maceral at the top of the seam is inertodetrinite [ 17]. Thicker fusain lenses contain fusinite and semifusinite. (In some cases discrete fusain lenses are observed toward the base of the seam.) Megascopically the lignite in this region
86 TABLE 3.7 Lithotype classes, lithotypes, and inclusions for Texas lignites [25]. Lithotype Class Pure coal, detrital
Lithotypes* Banded
Pure coal, non-xylitic
Unbanded Finely Moderately Moderately Highly Unbanded
Pure coal, xylitic Impure coal, detrital Impure coal, non-xylitic Impure coal, xylitic
Unbanded Finely Moderately Highly Moderately
Inclusions Gel particles Resin bodies Gelified groundmass Resin bodies Charcoal Gelified tissues Cuticles Gel particles Resin bodies Gelified groundmass Charcoal Resin bodies Charcoal
*Banding is classified as follows: finely, <2mm; moderately, >2mm, <5mm; and highly, >5mm.
of the seam appears to be more fragmental than lignite lower in the seam, and has a dull luster. Huminites dominate throughout the middle and lower portions of the Beulah-Zap lignite. Ulminite that is not extensively gelified associates with inertinites near the top of the seam, and may incorporate corpohuminite in the preserved cell lumens. The more highly gelified huminites are more abundant near the base of the seam. Gelinite and gelified ulminite occur in association with attritus above the underclay and clay partings [ 17]. Attrinite and desinite are more abundant near the base of the seam. The huminite macerals become more abundant, relative to the inertinites, toward the base of the seam, with ulminite, corpohuminite, and fusinite concentrating near the center [27]. The seam becomes more massive and displays a brighter luster with increase in huminites. No obvious pattern of liptinite distribution occurs [ 17,26], although attrinite, sporinite, and cutinite concentrate near the base [27]. Liptinites generally show very little vertical variation [ 10]. Maceral composition does not vary significantly in lateral directions [10]. Distributions of huminite and inertinite maceral groups in Beulah-Zap bed at the Freedom mine show a similar pattern to the Beulah mine, with inertinites more abundant near the top of the seam and the huminites more abundant toward the bottom [28]. A vertical variation in mean reflectance values in two stratigraphic sequences of Beulah-Zap lignite [29] shows the influences of the original environment of deposition. In Estevan (Saskatchewan) lignite, fusinite and semifusinite averaged 19% for the seam, but were concentrated in the lower two-thirds of the seam [30]. Exinite was distributed throughout the seam; the highest concentration was 13-20 cm from the top. Reflectance of eu-ulminites A and B increases downward for both the Estevan and Willow Branch (Saskatchewan) lignites [31 ]. This trend is not observed for corpohuminite [31]. Eu-ulminites of low reflectance also tend to have low
87 calorific values [31]. In Sandow (Texas) lignite, attrinite and desinite contents exceed ulminite in the upper part of the seam [25]. The upper portion also includes high concentrations of sporinite and thin-walled cutinite. Fusinite and semifusinite contents are low everywhere except in the upper portion. The middle of the seam contains abundant attrinite, desinite, liptodetrinite, and resinite. In the lower portion of the seam, a high huminite content is due to attrinite, desinite, and levigelinite. Sunrise (Louisiana) lignite consists of bright lithotypes and vitrite and clarite microlithotypes near the base, while the upper two-thirds is semibright with exinite, inertininte and mineral matter increasing while vitrinite decreases [32]. Column sections from the Dakota Colleries mine (Mercer County, North Dakota) show wide variations of petrographic composition with respect to depth [33]. (ii) Association with lithotypes. In Beulah-Zap lignites, huminite and inertinite macerals are more abundant in the vitrain and fusain lithotypes, respectively [10]. Liptinites are not predominantly associated with any particular lithotype, but tend to associate with the huminitegroup macerals. Generally ulminite is most abundant in vitrain; fusinite and semifusinite are abundant in fusain; and macerals with detrital origin (attrinite, desinite, liptodetrinite, and inertodetrinite) are common in attritus [6]. Petrographic data on the Freedom lignite has been shown in Table 3.1. Petrographic analysis of the lithotypes from the Beulah mine is shown in Table 3.8 [3,19]. TABLE 3.8 Petrographic analysis of Beulah lithotypes [3,19]. Vitrain Huminite Textinite Ulminite Attrinite Desinite Gelinite Corpohuminite Total Huminite ................. Liptinite. Sporinite Cutinite Resinite Suberinite Liptodetrinite Total Liptinite ................... Inertinite Fusinite Semifusinite Sclerotinite Inertodetrinite Micrinite Total Inertinite ................. *tr - trace
Durain
Fusain
4 0 tr* 64 34 27 10 16 9 4 5 3 1 2 1 4 2 2 84 .............. 59 .............. 42 3 2 1 1 1 9 ..............
2 1 1 2 2 7 ..............
1 1 1 2 2 5
tr 2 tr 2 1 5 .............
tr 10 1 20 tr 31 ..............
15 25 1 9 tr 49
88 As an indication of the variability in these same lithotypes, average maceral contents have been reported as follows: total huminite, 87% in vitrain, 71% in attritus, 16% in fusain; total liptinite, 7% in vitrain, 12% in attritus, 5% in fusain; and total inertinite, 5% in vitrain, 17% in attritus, and 63% in fusain [10]. Relative standard deviations in the range of 36-83% for the major macerals such as ulminite, attrinite, desinite, liptodetrinite, fusinite, semifusinite, and inertodetrinite [ 10], and relative standard deviations in many cases over 100% for the minor macerals [34], were observed for a suite of 96 samples of Beulah-Zap lignites. Comparable differences in maceral composition of lithotypes of Savage (Montana) lignite have been observed [35]. Ulminite is the major constituent of the vitrain lithotypes in the Beulah-Zap lignite, the vitrain containing up to 70% ulminite and 93% of all the huminite group macerals [ 10]. Eu-ulminite predominates among the huminite group macerals. Both the A and B varieties were observed, but A was the major constituent. Corpohuminite associates closely with ulminite. In a few cases, gelinite and highly gelified ulminite were the most abundant macerals. Gelinite occurs in thin, vitreous vitrain layers associated with a humodetrinite matrix. Most vitrain lenses have low concentrations of macerals other than the huminites [17]. Fusinite exhibited very well preserved cell structure. Inertinite macerals are the dominant constituent of fusain. Fusinite and semifusinite make up 61% of the total maceral content [10,17]. Ulminite occurs in all fusain samples, often with semifusinite at the boundaries of the fragments. Liptinite macerals associate more intimately with the huminites than with the inertinites. Humodetrinite macerals contribute the majority of the macerals that represent the detrital fragments in attritus [17]. Detrital macerals make up about 55% of the attritus [10,17], with humodetrinite constituting the majority [10]. However, the single most abundant maceral associated with attritus is ulminite [17]. Inertodetrinite occurs as elongated, angular fragments. (iii) Characteristics of lignite macerals. Low-rank vitrinites having a reflectance less than 0.5% are called xylinoids [36]. Several xylinoids may develop from a single chip of wood [36]. Xylinoids are the coalified remains of wood or bark. They belong to the vitrinite group of macerals [35]. (The term xylinoid has been used, mainly in the early literature, to refer to the macerals of the vitrinite group normally found in lignites [35]). In the lignite and subbituminous ranks, vitrinite reflectance varies relatively little as a function of rank. The maximum reflectance in oil changes from about 0.3% at 16.3 MJ/kg (m,mmf basis) to about 0.5% at 25.6 MJ/kg [37]. Consequently, vitrinite reflectance is questionable as an effective method of rank differentiation for the low-rank coals. The maxima in the fluorescence spectra of sporinite show a much greater change with rank, shifting from 40(0500 nm for peats to 630-670 nm for high volatile B bituminous [38]; sporinite fluorescence spectra provide a useful means of rank differentiation. In Canadian low-rank coals, fluorescence intensities decrease to a minimum at about 0.40% Rrandomand then increase again (as a function of reflectance) [39]. Eight northern Great Plains lignites from North Dakota, Montana, and Wyoming showed random reflectances ranging from 0.27 to 0.38% [40], the median value was 0.32%; the mean, 0.32%; and the standard deviation, 0.046. The ulminite reflectance of Freedom lignite was 0.36
89 (Rmax) [8]. Although this value was said to be low [8], it is in fact at the high end of data measured elsewhere [40]. Average random reflectance values for Texas lignites are higher than for North Dakota lignites [41]. Saskatchewan lignites show Rrandom of 0.27-0.33% [39]. At vitrinite reflectance values higher than 0.6% it is no longer possible to distinguish suberinite [42]. Similarly, as rank increases it becomes increasingly difficult to distinguish attrinite and desinite from collinite or desmocollinite [42]. Vitrinites can be characterized as structured, structureless, or groundmass vitrinite [30]. Structured vitrinite has, as the name implies, as well-defined cell structure. It is sometimes difficult to distinguish from semifusinite. Structured vitrinite may grade into the structureless form. Structureless vitrinite has few or no cell structures. The texture of structureless vitrinite is smooth, though sometimes cracked, and it has a higher reflectance than structured vitrinite. Groundmass vitrinite forms a groundmass for particles of other macerals. Groundmass vitrinite has a lower reflectivity than structured vitrinite. Vitrinite makes up, on average, 64% of the whole seam of Estevan lignite [30]. The range of vitrinite contents in individual samples was 48-80%. The vitrinite was about evenly divided among structured, structureless, and groundmass types. Structured vitrinite was most abundant at the top and bottom of the seam, as well as an interval about 43-71 cm from the top. Groundmass vitrinite was more abundant in the top half of the seam. Structureless vitrinite was about evenly divided in all seam intervals. Xylinite, detrinite, and dopplerinite are the counterparts of the vitrinite in higher rank coals [30]. As rank increases, these macerals become less diverse in both optical and chemical properties; eventually they form the vitrinite group. Xylinites are humic constituents of lignites whose most important characteristic is a well preserved cell structure. In detrinites the cell structure is discernable, though not as prominent as in xylinites. Detrinite may sometimes be observed as a ground mass containing spore or pollen remains, resin bodies, or particles of inertinites. Dopplerinite has undergone gelification and consequently has little or no discernable cell structure. Thus dopplerinite is more homogeneous than xylinite or detrinite. Ulminite in Hagel (North Dakota) lignite has a higher degree of gelification than Beulah-Zap lignite [43]. This difference suggests that these two Paleocene lignites may have had somewhat different depositional origins. The abundant woody material in the Hagel lignite, together with corroborative palynological data [44], suggests that the environment of deposition of the Hagel lignite was dominated by arboreal vegetation. The Beulah-Zap depositional environment was dominated by more abundant herbaceous plants. Ulminite dominates maceral the huminite group macerals, and in Beulah-Zap lignite accounts for 62% of the huminites [ 10 ]. The submaceral varieties of ulminite depend on the degree of gelification of the colloidal humic mass of degraded cellulose and lignin. Most ulminite in Beulah-Zap lignite is eu-ulminite, which is highly gelified and contains few preserved plant structures. Texto-ulminite is found in minor quantities near the top of the seam. In comparison, Martin Lake lignites (Texas) show well-preserved cell structure as texto-ulminite [25]. Many
90 huminites in deep (70-315 m) Wilcox (Texas) lignites have experienced partial or complete gelification [45]. Some are granular with a low reflectance and a weak orange fluorescence, possibly representing an early stage in the formation of micrinite. Micrinite is indeed found in close proximity to this type of huminite. The humodetrinite subgroup contains attrinite and desinite. These two macerals account for 35% of the huminite group and 20% of all macerals in the Beulah-Zap lignite [ 10]. The distinction between the two is based on size; humodetrinite <10 0rn is classed as attrinite. Attrinite is the most abundant humodetrinite maceral in Beulah-Zap lignite [ 10]. Attrinite, desinite, and levigeliniteare the principal huminites in San Miguel (Texas) lignite. Other huminite macerals in Beulah-Zap lignite include gelinite and corpohuminite, which together account for about 2% of the huminites [ 10]. Corpohuminite has a higher reflectance than normal for a huminite group maceral, due to its high hydrogen content, and is distinguished from inertinites by a characteristic bright oval or circular morphology in cross section. Corpohuminite is commonly associated with ulminite; differentiation between them is difficult in highly gelified samples. Anthraxylon derives from bark and woody tissues. During coalification, anthraxylon develops a homogeneous appearance and smooth texture. Anthraxylon is also characterized by a bright luster, conchoidal fracture, and brittleness. In thin section, anthraxylon has a translucent reddish color and often shows the structure of the woody tissue [ 15,16,46]. In thin sections cut normal to the bedding planes, anthraxylon appears as well-defined homogeneous bands running across the section. The so-called "woody" lignites are composed mainly of anthraxylon. The two most abundant inertinite macerals in Beulah-Zap lignite are fusinite and semifusinite [10]. Together they account for 55% of the total inertinites [10]. The reflectance of fusain from Beulah lignite is 1.73 [47]. Semifusinite differs from fusinite by having a lower reflectance and thicker cell wall structures. Both are extremely brittle. North Dakota lignite is richer in semifusinite than Texas lignite [41]. Fragments of detrital inertinites too small to determine a maceral type are classified as inertodetrinite. In the Beulah-Zap lignite most inertodetrinite particles are <25 ~tm in diameter [ 10]. Inertodetrinite comprises about 40% of inertinites in Beulah-Zap lignite [ 10]. Both macrinite and sclerotinite occur in trace amounts ( i.e., less than 1%) in Beulah-Zap lignite [ 10]. In Martin Lake lignite, fusinite and semifusinite show well preserved cell structure [25]. These two macerals, along with inertodetrinite, account for most of the inertinites in this lignite. Some inertodetrinites show rounded or corroded grain boundaries, indicative of transportation from outside the site of deposition. In comparison, inertinites in Big Brown (Texas) lignite are a mixture of sclerotinite, inertodetrinite, and macrinite. The mean inertinite reflectance for Martin Lake lignite exceeds that of other Wilcox Group lignites in Texas, suggesting the possible deposition of this lignite in a more highly oxygenated environment. Sporinite is distinguished from other liptinites by a characteristic elongated morphology. In Beulah-Zap lignite sporinite commonly occurs in the humodetrinite matrix and may range up to 200 ~tm in length [ 10]. Cutinite occurs as long, thin layers in a matrix of attritus. It comprises less than
91 2% of Beulah-Zap lignite [10]. Resinite also occurs in the attrital matrix, in bodies ranging from tens to hundreds of microns in diameter [10]. Texas lignite is richer in liptinites than North Dakota lignite [41]. In Martin Lake lignite the principal liptinites are sporinite and cutinite. Sporinite and cutinite are also the principal liptinites in San Miguel lignite, along with liptodetrinite. However, in Big Brown lignite, liptodetrinite is equal or higher in content to the sporinite and cutinite. Resinite occurs in Big Brown lignite in globular form and in exsudatinite form. (iv)
Comparative petrographic compositions of lignites. Lignites
are more petrographically
heterogeneous than higher rank coals [41]. The petrographic compositions of six North Dakota lignites are summarized in Table 3.9 [10]. Compilations of petrographic analyses of lignites prior to 1950 have been published [46,48], including some data on the vertical variability of petrographic composition within a seam [46]. In addition, the report [46] is an excellent guide to the literature published prior to 1950 on the occurrence and petrography of lignites. TABLE 3.9 Bulk maceral analyses of North Dakota lignites (Vol. pct.) [ 10]. Lignite*
CEN
FAL
FRE
GAS
IND
VEL
52 24 tr tr 1
41 29 2 1 2
37 25 3 1 1
42 22 3 1 1
38 35 2 1 1
39 27 3 1 2
Sporinite Cutinite Resinite Suberinite Liptodetrinite
1 1 1 0 3
3 1 1 0 3
2 1 1 0 7
1 1 1 0 4
2 1 1 tr 6
tr 1 2 tr 4
Fusinite Semifusinite Macrinite Sclerotinite Inertodetrinite
1 10 0 tr 3
1 6 0 0 7
3 4 0 tr 10
1 2 0 tr 4
3 2 0 tr 7
7 5 tr tr 8
3
3
3
3
2
tr
Ulminite Attrinite Desinite Gelinite Corpohuminite
Minerals
*CEN - Center; F A L - Falkirk; FRE- Freedom; GAS - Gascoyne, Blue Pit; IND- Indian Head; V E L - Velva; tr- trace.
92 3.2 THE CARBON SKELETON
This section begins a discussion of the molecular architecture of lignites, with specific concern for the carbon framework. The two subsections treat the aromatic carbon and the aliphatic carbon, respectively. In each of these subsections the discussion is divided, for convenience, according to the principal experimental technique used. The macromolecular or three-dimensional structural arrangements in lignites are treated separately in Section 3.4. 3.2.1 Aromatic carbon (i) Oxidation studies. Oxidation of lignite with a variety of oxidants indicates that the predominant aromatic structures are benzene and phenol rings [49,50]. Hydroaromatic structures, such as tetralin fragments, may also be important [49,50]. Structures containing more than one ring are fairly rare. Polycyclic and heterocyclic ring systems are not important components of the structure [49]. Oxidation of Decker (Wyoming) lignite with 0.4 M sodium dichromate at 250~ for 40 h produced no aromatic products containing more than two fused rings [51,52]. (In contrast to some other oxidizing agents, sodium dichromate tends to preserve polynuclear aromatic systems, rather than degrading them to benzenecarboxylic acids.) Naphthalenecarboxylic acids were only about 10% as abundant as benzenecarboxylic acids from the dichromate oxidation of Sheridan (Wyoming) lignite [52]. Zap lignite produced benzenecarboxylic acids as the major products (accounting for about 82% of all acids identified) with very minor amounts of naphthalenecarboxylic acids (about 3%) and no phenanthrenecarboxylic acids [53]. In terms of relative abundance, the major aromatic units (identified as methyl esters of carboxylic acids or as neutral compounds) were benzene, 100; naphthalene, about 11; anthraquinone (1), about 2; and 9fluorenone (2), about 5 [54]. O
O
O 1
2
Oxidation of Estevan lignite with aqueous potassium permanganate at 60-70~
produced
47.3% yield of benzoic acids, with 21.4% oxalic acid and 6.8% acetic acid [55]. Expressed in terms of the carbon content of the original lignite, 1.7-3.8% of the carbon appeared as acetic acid, 6-8% as oxalic acid, and 45-50% as benzoic acids [55]. The benzoic acids identified, but not quantified, included phthalic (3), isophthalic (4), terephthalic (5), hemimellitic (6), trimellitic (7),
93 COOH
COOH
~L~COOH
4
~
~
COOH
COOH
COOH COOH COOH 7
~
5
COOH COOH
HOOC ~
COOH
COOH
~,
ZCOOH 8 COOH
COOH COOH
COOH
COOH HOOC
HOOC ~COOH HOOC~
COOH
COOH
COOH 10
~COOH
11
trimesic (8), mellophanic (9), pyromellitic (10), benzenepentacarboxylic, and mellitic (11) acids. Formation of polycarboxylic acids having adjacent carboxyl groups (i.e., all of the polycarboxylic acids except trimesic) implies existence of larger fused ring systems. Potassium permanganate oxidation of lignite from Oliver County, North Dakota produced mainly benzenedi- and tricarboxylic acids as the aromatic oxidation products [56]. Permanganate oxidation of sporinite from North Dakota lignite produced methoxy- and hydroxybenzene carboxylic acids [57]. Phthalic acid was the most abundant aromatic acid in the permanganate oxidation products of methylated Sheridan lignite [58]. Aromatic acids from the oxidation of Beulah lignite with ruthenium tetroxide are listed with the aliphatic acid products in Table 3.14; tetra- and pentacarboxylic acids predominated among the benzenecarboxylic acids [59]. The relatively large yields of benzenetri-, tetra-, and pentacarboxylic acids suggest a preponderance of fused ring systems [60], in general agreement with permanganate oxidation of Estevan lignite, although such interpretation conflicts with other oxidation studies [49,50] and calorimetry studies [61 ]. The relative unimportance of naphthalene rings is indicated by a low yield of phthalic acid. Oxidation of Rockdale (Texas) lignite with ruthenium tetroxide produced about 10-15 mole percent of benzenecarboxylic acids among the products [62]. The most abundant was phthalic acid, in contrast to the results obtained with Beulah lignite. It has not been established whether this distinction has any implications for the organic geochemistry of these two lignites. Neither 4 nor 5 were found in the Rockdale lignite oxidation products, nor was 8.
94 The product ratios of the acids 3, 6, 7, and 10 were 20:20:10:1. Some methylbenzenecarboxylic acids were also produced. These results indicate that ortho-substitufion patterns on the aromatic rings are important in the structure of this lignite, and that biphenyl-type structures are insignificant. The di-acids and tri-acids result from oxidation of such structures as naphthalene, naphthols, and heterocyclic compounds of oxygen. The low yield of the tetra-acid relative to the diand tri-acids indicates that condensed aromatic structures, such as anthracenes and phenanthrenes, are not important components of the structure of this lignite. The high yield of phthalic acid (3) relative to the 1,3- and 1,4- diacids is evidence for 1,2- fusion patterns in this lignite [63]. This type of ring fusion is further corroborated by the higher yields of 6 and 7 relative to 8. The formation of trimellitic acid (7) suggests that 2-arylnaphthalene structures might be important in the structure of this lignite. Oxidation of Sheridan lignite with acetic acid and hydrogen peroxide at 400C for 10 days caused 80% conversion to methanol-soluble acids [54]. The active oxidant in this system is peroxyacetic acid, which oxidizes naphthols to phthalic acid, but does not convert phenols to muconic acids (oxidation products of phenols that form by oxidative destruction of the aromatic ring; e.g., phenol itself is converted to the parent muconic acid, 2,4-hexadienedioic acid). Of the aromatic products, 69% were benzenecarboxylic acids and 31% methoxybenzenecarboxylic acids [541. Oxidation of Sheridan lignite with 70% nitric acid at reflux for 16-24 hours resulted in a 70% recovery of benzenecarboxylic acids [52]. The approximate percentages of the acid products were di-acids, 3%; tri-acids, 37%; tetra-acids, 39%; benzenepentacarboxylic acid, 15%, and mellitic acid (11), 4%. The low yield of mellitic acid, whose formation indicates extensive ring condensation, suggests that highly condensed ring structures are not important in this lignite. In comparison, nitric acid oxidation of three Chinese lignites formed alkylated aromatic dicarboxylic acids, in which the aromatic moiety was benzene, naphthalene, anthracene, or phenanthrene [64]. Benzenecarboxylic acids were the primary products from oxidation of Sheridan lignite by bubbling air through an HC1 solution while irradiating with ultraviolet light [52]. Photochemical oxidation of Decker lignite for eight days with a mercury lamp also produced a series of benzenecarboxylic acids as the primary products [51]. Benzenepolycarboxylic acids were the major aromatic products of oxidation of Wyoming lignite with, six oxidizing agents: potassium permanganate, alkaline cupric oxide, nitric acid, sodium dichromate, peroxytrifluoroacetic acid, and cesium fluorosulfonate [49]. Reaction with alkaline copper(II) oxide produced phenolic acids similar to typical oxidation products of lignin. Formation of the pyridinium iodide of lignite, followed by alkaline silver oxide oxidation, yields aliphatic- and aromatic-rich fractions [65]. Application of this reaction sequence to a Wyoming lignite forms alkylbenzenes as the major aromatic components. Lesser amounts of naphthalenes, aromatized sesquiterpenoids, indanes, tetralins, and fluorenes were produced. No evidence was found for aromatics of more than four tings. Among the phenolic compounds, phenol, cresols, anisole, and xylenols were abundant.
95 (ii) Nuclear magnetic resonance. The distribution of aromatic carbon types in two samples of Beulah-Zap lignite is summarized in Table 3.10 [66]. TABLE 3.10 Distribution of aromatic carbon types in Beulah-Zap lignite* [66] Sample Carbon type Total aromatic carbon (Ira) Aromatic carbon in an aromatic ring (fa') Carbonyl carbon (fac) F'rotonated aromatic carbon (faH) Nonprotonated aromatic carbon (faN) Phenolic or phenolic ether carbon (faP) Alkylated aromatic carbon (fas) Aromatic bridgeheads (faR)
A 0.61 0.54 0.07 0.26 0.28 0.06 0.13 0.09
O 0.66 0.58 0.08 0.21 0.37 0.08 0.16 0.13
*A = Argonne premium sample; O = sample presumed to be oxidized,
The value for protonated aromatic carbon, faH, observed in this experiment is similar to that for high volatile bituminous coals [66]. This behavior is unusual in that generally, for coals ranging from lignite through low volatile bituminous, faH increases with rank. The North Dakota lignite is anomalous in this respect. Considerable debate exists about appropriate methods and techniques for obtaining accurate, quantitative NMR data on coals. Values of fa and other structural parameters are clearly sensitive to the experimental method used, even when different methods are applied to portions of the same sample of a given lignite. For Beulah-Zap lignite, fa determined by cross-polarization magic angle spinning (CPMAS) at a magnetic field strength of 2.3 Tesla is 0.66. The same sample, analyzed at 4.7 Tesla in an experiment designed to suppress spinning side bands in the spectrum, showed an fa of 0.69 [67]. CPMAS fa measurements for Beulah-Zap lignite made at another laboratory were 0.67-0.70 [68], with some dependence on frequency, measurements being made at 25 and 75 MHz. Single-pulse excitation spectra of the same lignite indicated fa of 0.74-0.76 at 25 MHz and 0.77 at 75 MHz [68]. About 95% of the carbon in the lignite was observed in singlepulse excitation at 25 MHz. Treatment with samarium iodide gave fa of 0.68-0.70 in a CPMAS experiment, with 55% of the carbon observed [69]. Applying the Bloch-decay method to the SmI2treated lignite allowed observation of 65% of the carbon, with fa found to be 0.74. Depending on the method of choice, fa of Beulah-Zap lignite can be measured as 0.61-0.77. In somewhat similar work, the aromaticity of a Powder River Basin lignite was 0.55 when measured by cross polarization, and 0.58 determined by Bloch decay [70]. Using hexamethylbenzene as an internal standard, the Bloch decay measurement observed 65% of the carbon, while the cross polarization
96 experiment observed 55%. Distribution of carbon types in two Canadian lignites, an Ontario lignite and Bienfait (Saskatchewan) lignite, is summarized in Table 3.11 [71]. The data were obtained by dipolar dephasing techniques. Some data on the aliphatic carbons are shown also for completeness; aliphatic carbon is discussed in the following subsection. TABLE3.11 Distribution of carbon types in Canadian lignites [71]. Carbon type Total aromatic carbon (fa) Fraction of aromatic carbon nonprotonated (faa,N) Fraction of aromatic carbon protonated (faa,H) Fraction of all carbon protonated and aromatic (faH) Methyl carbon mass fraction (fMe) Lowest value reported Highest value reported Mobile methine and methylene; quaternary carbon, rotating methyl (fw) Rigid methyl, methine and methylene (fs)
Ontario 0.61
Bienfait 0.70
0.59 0.41
0.85 0.15
0.25
0.11
0.19 0.31
0.18 0.28
0.14 0.86
0.39 0.61
For comparison, the fa of Estevan lignite is 0.58-0.60 [39]. Values of fa of 0.61 and 0.62 are observed for an Ontario lignite, the higher value obtained by CPMAS at 2.3 Tesla, and the lower in an experiment at 4.7 Tesla to suppress spinning side bands [67]. Structural parameters for a variety of lignites, as determined by cross polarization - magic angle spinning NMR, are shown in Table 3.12 [39]. The table headings are defined as follows: fa, fraction of aromatic carbons; fall, protonated aromatic carbons; faN, non-protonated aromatic carbons; fsH, protonated aliphatic carbons; and fsN, non-protonated and methyl carbons. TABLE3.12 CP/MAS NMR Structural parameters of lignites [39] Sample* 1 2 3 4 5 6
%C 67.5 69.9 70.3 68.0 72.9 ....
H/C 0.94 0.89 1.12 0.65 0.87
f_a__ 0.64 0.55 0.37 0.43 0.64 0.57
fall 0.17 0.40 0.30 0.29 0.49 0.38
0.47 0.15 0.07 0.14 0.15 0.19
0.25 .... .... 0.46 .... ....
0.11 0.11
*Samples are identified as follows: 1, Beluga, Alaska; 2, Chester, Mississippi; 3, Henning, Tennessee; 4, King Cannel, Utah; 5, Oxbow, Louisiana; and 6, Thermo, Texas. Table headings are defined in text.
97 Although there is certainly a spread in values of fa, for the ten lignites characterized by the data in Tables 3.10 to 3.12, eight of the ten fa values lie in the range 0.55-0.70, and six are in the narrower range 0.57-0.66. The values for faH and faN vary more widely, although seven of the ten values of faHlie in the range 0.20--0.40. A variety of other lignites has been studied at least sufficiently to obtain a value of fa. Reported values include 0.57 for both a Canadian lignite [72] and Pust (Montana) lignite [73], 0.55 for a Wyoming lignite [74], and 0.44 for Rockdale [73] and Big Brown lignites [75]. In comparison with the data on North American lignites, fa values of 0.58 and 0.64 have been determined for, respectively, Central Otago and Southland (both New Zealand) lignites [76]. (iii) Calorimetric measurements. The estimation of aromaticity, fa, can be performed using a pressure differential scanning calorimeter (PDSC) [61,77]. A 1-1.5 mg sample o f - 1 0 0 mesh coal is heated in a 3.5 MPa atmosphere of oxygen between 150 and 600~
at a linear rate of
20*/min. The thermograms usually consist of two exothermic peaks; the lower temperature peak is assigned to the aliphatic carbon and the higher temperature peak to aromatic carbon. An example of the PDSC thermogram for Ledbetter (Texas) lignite is shown as Fig. 3.1 [78]. The assignment of the low-temperature peak to aliphatic carbon and the high temperature peak to aromatic carbon is based on model compound studies [61]. A wide variety of model compounds were studied by PDSC, ranging from the purely aliphatic to purely aromatic, nTetracontane (n-C4oH82) has a single, low-temperature peak at 215~
a temperature lower even
than the low temperature peak of a sample of Minnesota peat. In contrast, phenanthrene produces a single peak at 410~
in the temperature range characteristic of the high temperature peak in the
thermograms of subbituminous coals. Retene (7-isopropyl-l-methylphenanthrene, fa = 0.78) produced a thermogram with a small low-temperature peak and a more prominent high temperature peak, remarkably similar to that of Rosebud (Montana) subbituminous coal as shown in Fig. 3.2 [61]. An "apparent aromaticity" is determined by taking the ratio of the high temperature (presumably aromatic) peak height to the sum of the heights of both peaks. For run-of-mine coals, the aromaticity is then calculated from the equation fa = 0.263 + 0.868x where x is the apparent aromaticity [77]. The linear least squares coefficient of determination r2 is 0.85. The original basis on which this relationship was established required knowledge of the "true" aromaticity of the samples; this was determined from the Teichmuller plot of fa vs. maf carbon content [79]. Thus for example an aromaticity of 0.60 was derived from PDSC data for a Beulah lignite [23]. This value is at the low end of those obtained from NMR measurements discussed above, but measurements were not made on the same samples. Separated lithotypes of Beulah lignite gave values of 0.94 for fusain, 0.64 for vitrain, and
98 100
80
60
40
20
0
,
100
I
200
,
I
300
,
I
,
400
I
500
600
Temperature, *C Figure 3.1. PDSC thermogram of Ledbetter lignite [78].
0.63 for attritus [3,77,79]. The remarkably high value for the fusain lithotype of this sample was not observed for fusains of other lignites, but the data for vitrain and attritus are generally comparable with other observations shown in Table 3.13 [80,81]. TABLE 3.13 Aromaticities of lithotypes of Fort Union lignites [80,81].
Lignite Beulah Gascoyne Glenharold Indian Head Velva
Vitrain Attritus Fusain 0.65 0.66 0.80 0.54 0.71 0.78 0.63 0.62 0.67 0.71 0.71 0.77 0.66 0.65 0.86
Whole Coal Calcd.* Exptl. 0.66 0.66 0.64 0.57 0.63 0.63 0.71 0.68 0.66 0.70
*Calculated from the aromaticities of the individual lithotypes, weighted for the amount of each present in the unseparated samples. The aromaticities of the vitrain and attritus are very similar, with the single exception of Gascoyne, and are always lower than the value for fusain. Core samples of Ledbetter (Texas) lignite showed a slight decrease in aromaticity with
99 200
I
'
'
I
'
I
'
I
,
P.
,/" "'~,
I00
0 100
,
I
200
,
I
300
/
,
!
I
400
,
I ~
500
600
Temperature, ~ Figure 3.2. PDSC thermogram of retene (solid line) and Rosebud subbituminous coal (dashed line) [61].
depth, ranging from 0.65 for the Brown seam at 21-28 m to 0.56 for the Green seam at 55-58 m [20,77,79]. The thermograms were very similar in shape and positions of the peak maxima on the temperature scale to those of poly(vinyltoluene), for which fa is 0.66. A comparable study of Baukol-Noonan (North Dakota) lignite showed less variability, albeit over a much narrower vertical span. Over 2 m the aromaticity varied from 0.66 to 0.71 with a standard deviation of 0.02. Nevertheless it did decrease slightly with depth, from 0.71 two meters above the base of the unit to 0.68 at the base. Petrographic data were not available for either set of samples. (iv) Other methods of determining aromaticity. An aromaticity of 0.60 was estimated for a Montana lignite by X-ray diffraction studies [82], based on a resolution of two peaks, the (002) band typical of the interplanar spacing in highly condensed aromatic systems (most notably graphite) and the y band observed, for example, in paraffin and attributed to the spacing between disordered aliphatic or alicyclic structures. An innovative but seldom-used method involving reaction of coal with fluorine indicated a value of 0.52 for a Wyoming lignite [83]. Fourier transform infrared (FFIR) spectroscopy of Beulah lignite indicated fa of 0.84 [84]; well above the aromaticities usually found for lignites, unless the sample happened to be fusain-rich. FTIR examination of Titus (Texas) lignite showed 0.7% aromatic C-H and 4.1% aliphatic C-H [85]. (v) Ring condensation. For an aromatic ring system with a given number of condensed rings, the H/C atomic ratio will vary depending on the type of condensation. That is, for
1 O0 pericondensation, where the rings are as condensed as completely as possible, the H/C ratio will be lower than for a cata- condensed system, in which condensation is minimal. Examples of peri- and catacondensed four-ring systems would be pyrene (12) and chrysene (13), respectively. The relationship between the H/C ratio and the number of rings for peri- and catacondensation has been shown graphically [86]. The relationship between atomic H/C ratio and carbon content has also been shown graphically [87]. Thus for a known carbon content it is possible to estimate the H/C ratio and, from that, the number of condensed rings. In the case of coals having 70--83% carbon, the average ring number found in this way is two [86]. (For two condensed rings there is no difference between peri- and catacondensation, since the only possible structure is naphthalene.) Indeed, most studies of ring condensation suggest that the aromatic ring number of "younger coals" is 1-2 [88]. The average aromatic unit in lignites is estimated to contain nine atoms [89], again implying a mixture of one- and two-ring systems.
12
13
Many oxidation studies also suggest that the aromatic ring systems in lignites are small, with benzene and naphthalene structures predominating. Degradation of lignite with alkaline copper(II) oxide, a reagent used for lignin depolymerization, showed that benzene and phenol structures are the predominant aromatic components [49]. NMR of Beulah-Zap lignite indicates that the aromatic cluster size is nine carbon atoms [66]. The mole fraction of bridgehead carbons is 0.17, with three attachments per cluster and an average molecular weight of 277 [66]. NMR of pyridine extracts from North Dakota lignites that had been treated with sodium hydroxide and ethanol at 300"C for up to two hours shows a total ring number per structural unit of 3.0-3.5, with an aromatic ring number per cluster of 1.5-2.0 [90]. There are on average about 1.5 naphthenic rings per cluster. The aromaticities of these extracts were in the range 0.60-0.66. NMR of Nakayama (Japan) lignite showed that the petroleum-ether-soluble portion of the pyridine extract had single aromatic or quinone tings [91]. The portion of the pyridine extract soluble in chloroform but insoluble in petroleum ether had both single and double ring systems. The temperature of the maximum in the aromatic (high-temperature) peak in the PDSC thermogram was determined for model compounds containing one to five fused aromatic tings.
I01 Generally the temperature maximum of the high temperature peak increases with increasing ring condensation. Similarly, the high temperature peak maximum increases for coals of increasing rank. Although the data have sufficient scatter to warrant plotting as a band rather than as a line, nevertheless in the rank range peat-bituminous the band for the coal samples is remarkably congruent with the band for the model compounds [61]. This similarity of behavior was used to infer that the average ring condensation in lignites is about 1.5 to 2 fused rings per aromatic cluster [23,61]. X-ray diffraction shows that the average diameter of aromatic layers in lignites is about 0.5 nm, consistent with, on average, 7 to 8 atoms per layer [92]. (Considering the differences in techniques used, this is in good agreement with other estimates [66,89] of 9 atoms per aromatic cluster.) The average bond length between atoms in the layers is about 0.1387 nm, for comparison, the length of the C-C bonds in benzene is 0.139 nm [93]. The spacing between layers in lignites is 0.37-0.435 nm, compared with the interlayer spacing in graphite of 0.335 nm. Lignites at the upper end of this rank range show the beginnings of the characteristic (002) band of graphite in the x-ray diffractograms. Pyrolysis/mass spectrometry of Texas lignite indicated the presence of naphthalene-derived structures such as tetralin, dihydronaphthalene, and alkylated naphthalenes, as well as tetrahydroanthracene [94]. Single ring structures predominate among the aromatic compounds in a supercritical fluid extract of lignite [95]. 3.2.2 Aliphatic carbon This subsection discusses the principal forms of aliphatic carbon in lignites, the methods by which they have been studied, and estimates of the amounts of the various aliphatic structures. (i) Oxidation studies. Oxidation of Beulah lignite with ruthenium tetroxide gave relatively high yields of succinic and glutaric acids (totalling 18.3 area % of the gas chromatogram of the methylated products) [60]. This result implies that the major links between aromatic units in this lignite are dimethylene and trimethylene bridges. (Some keto structures, such as tetralone, could also contribute to the formation of these acids.) Succinic acid is the aliphatic dicarboxylic acid produced in greatest amount [96]. This suggests that either dimethylene bridges or hydroaromatic structures such as 4,5-dihydropyrene are major contributors to the structure of this lignite. Oxidation at 27~
in the presence of a phase-transfer catalyst yielded 2.7% succinic, 2.5%
glutaric, and 1.2% adipic acids (maf basis) [97]. The percentage of the carbon in this lignite present in each of the types of aliphatic bridging groups is dimethylene (and possibly 2-tetralone structures), 1.5%; trimethylene, 1.5%; and tetramethylene (and possibly tetralin), 0.7% [3]. Only small amounts of aliphatic monocarboxylic acids were produced from this lignite during ruthenium tetroxide oxidation. A complete analysis of acids observed in the ruthenium tetroxide oxidation of Beulah lignite is shown in Table 3.14 [59,98,99]. The major products are aliphatic dicarboxylic acids and benzene polycarboxylic acids [ 100].
102 TABLE 3.14 Yield of acids from ruthenium tetroxide oxidation of Beulah lignite, % maf [59,98,99]. Acid Succinic 2-Methylsuccinic Glutaric 2-Methylglutaric Adipic 2-Methyladipic Pimelic Suberic Azeleic Sebacic Octanoic Nonanoic Lauric
Yield 2.38 0.41 0.59 0.26 0.11 0.07 0.04 0.12 0.04 0.01 0.02 0 <0.01
Acid Yield Myristic 0.01 Palmitic <0.01 1,2,3-Propanetricarboxylic 0.70 1,2,4-Butanetricarboxylic 0.31 Phthalic 0.07 1,2,3-Benzenetricarboxylic 0.23 1,2,4-Benzenetricarboxylic 0.30 1,3,5- B enzenetricarboxyli c 0.01 1,2,3,4-Benzenetetracarboxylic 1.5 1,2,4,5-Benzenetetracarboxylic 1.53 1,2,3,5-Benzenetetracarboxylic 1.5 Benzenepentacarboxylic 1.5 B enzenehexacarboxylic 0.01
Some ambiguity arises because certain of the aliphatic diacids could be produced from two structures: polymethylene bridging groups or hydroaromatic structures. A suspension of Beulah lignite in xylene was dehydrogenated by refluxing with dichlorodicyanoquinone [59,98]. The yield of succinic acid from subsequent ruthenium tetroxide oxidation decreased from 2.38% in the untreated lignite to 1.42% in the dehydrogenated lignite. This result suggests that about half the succinic acid may derive from dihydrophenanthrene or dihydropyrene structures. Further corroboration is an increase in yield of phthalic acid, from 0.07 to 0.22%. The increased yield of phthalic acid from the dehydrogenated lignite is attributable to dehydrogenation of dihydrophenanthrene or dihydropyrene structures. In comparison, the yields of adipic acid from the untreated and dehydrogenated lignite were 0.11 and 0.12%, respectively. Thus very little of the adipic acid arises from tetralin-like hydroaromatic structures; only about 10% of the C4 units are present in tetralin structures [101]. Dehydrogenation of a fairly aliphatic Big Brown lignite (fa of 0.44) with dicyanodichloroquinone also reduced the succinic acid yield by about 50%, from 2.06% in the untreated lignite to 1.01% in the dehydrogenated lignite [75], again suggesting that about half of the aliphatic precursors to succinic acid are present in hydroaromatic structures based on dihydropyrene or dihydrophenanthrene moieties. Similar reductions, of about 50%, were observed in yields of glutaric acid and adipic acid, suggesting that about the half the total yield of these acids results from the oxidation of indan and tetralin (respectively) moieties. Comparison of the yields of major acids before and after dehydrogenation suggests that tetralin-like structures
(i.e., tetrahydroaromatics) are only about 10% as plentiful as the dihydroaromatics in this lignite. Interpretation of data from the ruthenium tetroxide oxidation is complicated because a given acid product many not be related unequivocally to a particular structure in the lignite. For example, 1,5-pentanedicarboxylic acid arises from at least four types of structures [62], trimethylene bridges between aromatic units, indan, 1-aryltetralins, and structures of the type Ar(CH2)3(CH)(Ar)2.
103 Malonic acid is a very minor product in the ruthenium tetroxide oxidation of diphenylmethane. Consequently, absence of malonic acid from the aliphatic dicarboxylic acid products is not necessarily an indication of the absence of single methylene carbon bridges from the lignite structure. The formation of benzene polycarboxylic acids implies extensive crosslinking of the structure, though some carboxyl groups are already present in the lignite even before oxidation. Methylation of Beulah lignite with methyl-d3 iodide prior to oxidation with ruthenium tetroxide showed that about 10% of the aliphatic diacids were produced from the oxidation of arylalkanoic acids [59]. An example would be the formation of succinic acid from 3-arylpropanoic acid structures. During oxidation with ruthenium tetroxide acetic, propionic, and butyric acids (and, in principle, higher acids) are produced from alkyl side chains. Since oxidation preserves the ring carbon to which the side chain was attached, a methyl side chain produces acetic acid; ethyl, propionic acid, etc. This method showed the following percentages of carbon incorporated in each type of side chain in Beulah lignite: methyl, 1.8%; ethyl, 0.14%; propyl, 0.04% [3,97]. Oxidation of Rockdale lignite with ruthenium tetroxide produced about sixty aliphatic acids [62]. All of the dicarboxylic acids from four to eleven carbon atoms were found. Virtually every isomer of the diacids containing five, six, or seven carbon acids was found, as well as a variety of tri- and tetraacids. The predominant acids among the products included butanedioic, pentanedioic, 2-methyl-l,4-butanedioic, hexanedioic, 2-methyl-1,5-pentanedioic, heptanedioic, octanedioic, nonanedioic, 1,2,3-propanetricarboxylic, phthalic (3), and 1,2,4-benzenetricarboxylic (7) acids [63]. These results show that branched aliphatic structures are relatively abundant in this lignite. About twenty aliphatic tri- and tetracarboxylic acids were observed in the oxidation products from Rockdale lignite [63]. Although unambiguous structures were not assigned, the results suggest the presence of branch points such as
~
H 2 ---CH ---CH 2 - - - ~
D Oxidation of various lignites with ruthenium tetroxide provided evidence for methylene bridges of two to twelve carbons [ 102]. As discussed above, the method is not a satisfactory test for single methylene carbons. The relative amounts of the various methylene bridges decrease with increasing length of the bridge. Oxidation of various lignites with ruthenium tetroxide in the presence of a phase-transfer
104 catalyst [100] was used to compare the yields of six acids: succinic, glutaric, adipic, 1,2,3propanetricarboxylic, phthalic (3), and 1,2,4,5-benzenetetracarboxylic (10). The results are shown in Table 3.15 [59,98,99]. The results of ruthenium tetroxide oxidation of lithotypes of Beulah lignite are shown in Table 3.16 [59,98,99]. TABLE 3.15 Comparative yields of acids* from ruthenium tetroxide oxidation of lignites, % maf. [59,98,99] Lignite Beulah Gascoyne Velva Martin Lake SanMiguel
SU 2.38 2.58 2.71 2.50 2.94
GL 0.59 0.56 0.56 0.96 0.61
AD 0.11 0.13 0.16 0.27 0.12
l:rI" PH 0.70 0.07 0.62 0.07 0.73 0.05 0.76 0.09 0.62 0.04
BT 1.53 1.60 1.37 1.55 0.73
*SU, succinic; GL, glutaric; AD, adipic; FrF, 1,2,3-propanetricarboxylic; PH, phthalic; BT, 1,2,4,5-benzenetetracarboxylic.
TABLE 3.16 Yields of acids* from ruthenium tetroxide oxidation of Beulah lithotypes, % maf [59,98] Lithotype Vitrain Attritus Fusain
SU 2.41 2.10 1.38
GL 0.60 0.50 0.33
AD 0.08 0.12 0.10
PT 0.58 0.52 0.27
PH 0.02 0.08 0.15
BT 0.71 1.38 1.40
*See note for Table 3.15 above.
Comparison of Tables 3.15 and 3.16 shows a wider variation in the amounts of these six acids among the lithotypes of a single lignite than among "whole" samples of different lignites. This finding highlights the great variability in samples from a single mine, and indicates the need for reporting petrographic data (whenever it exists!) with other analytical results. Furthermore, correlation of data from different experiments with the same lignite may be questionable unless all of the experiments have been done with the same sample. Reaction of a North Dakota lignite with peroxytrifluoroacetic acid indicated that 5.5% of the hydrogen originally in the lignite was identified in succinic acid, and 1.2% in malonic acid [103]. Succinic acid is produced from bibenzyl-type linkages, including 9,10-dihydrophenanthrene- and acenaphthene-type structures, -CH2CH2CO- linkages, and indans [103]. Malonic acid presumably arises from single methylene bridges, such as diphenylmethane-type structures. Oxidation converted 3.9% of the hydrogen originally present in the lignite to acetic acid [ 103]. This
105 reaction should convert methyl groups attached to aromatic rings to acetic acid. Reaction of Hagel lignite showed that 0.20% of the carbon was present as arylmethyl groups and 0.06% as arylethyl groups [ 104]. There was no evidence for the existence of arylpropyl structures [ 104]. In contrast, sodium hypochlorite oxidation indicates that about 1% of the total carbon in low-rank coals is present in n-butyl groups and 3-5% is in n-propyl groups [ 105]. Sheridan lignite, methylated with dimethyl sulfate to protect phenolic rings from attack, was oxidized with sodium dichromate. No long-chain acids were produced; but they were formed from a cannel coal containing 19.2% exinite [ 106]. (Sheridan lignite contains about 1% exinite.) The difference in behavior between the cannel coal and Sheridan lignite suggests that the lignite structures responsible for the formation of long-chain acids during oxidation are not the same as the aliphatic structures in cannel coal [ 106]. The latter derive from spores or pollen. Lignite can be separated into aliphatic- and aromatic-rich fractions by treatment with iodine in pyridine, followed by alkaline silver oxide oxidation of the resulting pyridinium iodides [65]. The aliphatic-rich fraction contained materials of molecular weights 60(05000, and was similar in composition to alginite or Type I kerogen, in agreement with results from dichromate oxidation [ 107]. The major fragments observed in solid probe mass spectrometry were alkanes and alkenes up to C 20, alkylated monocyclic alkanes and alkenes, sterane (14), sterene (15), 4-methylsterene (16), tri-, tetra- and pentacyclic terpanes, pentacyclic terpenes, and benzenes and phenols having long chain alkyl substituents.
C 14
15
16 Sheridan lignite contains aliphatic-rich materials similar to Type I kerogen, but not directly
106 related to exinite macerals [ 108]. Oxidation with potassium permanganate produces large amounts of aliphatic dicarboxylic acids in the range C4 to C21, with the C9 acid being most abundant [49,58,108]. Comparable results were obtained in the oxidation of Soya (Japanese) lignite [49]. Branched dicarboxylic acids in the range C5 to C10 and tricarboxylic acids in the range C6 to C8 were also identified in the oxidation products from the Sheridan lignite, but in much lower concentrations than the dicarboxylic acids [58,108]. These compounds might derive from material similar to Type I kerogen; that is, from lipid-rich organic material. Phthalic acid and 1,2,4- and 1,2,3-benzenetricarboxylic acids were abundant among the aromatic products of oxidation [ 108]. Oxidation products from methylated Sheridan lignite are similar to those produced from Green River oil shale [ 107]. Specifically, straight-chain aliphatic diacids were abundant in the range C3 to C15, with a maximum at C9 [107]. Diacids with branched chains or cyclic structures were observed only in much lower quantity. Treatment of Sheridan lignite with 15% nitric acid at 80"C for 14 h yields 11-13% aliphatic diacids in the range C4_C12[49]. Aliphatic diacids in the range C4-C13 were produced by oxidizing this lignite with CsFSO4 [49]. Potassium permanganate oxidation of sporinite isolated from a North Dakota lignite yielded straight-chain dicarboxylic acids as the major class of product [57]. Branched-chain diacids and tricarboxylic acids were minor products. Oxidation with nitric acid showed diacids in the range of C a to C13 [57].
(ii) Nuclear magnetic resonance. NMR of Big Brown lignite shows it to be more aliphatic than typical North Dakota lignites, having an aromaticity of 0.44 [75]. NMR suggests that much of the aliphatic carbon is present is polymethylene chains. Polymethylene structures containing at least four --CH2-- units have been observed by liquefaction in tetrahydroquinoline followed by NMR analysis of the deuterochloroform-solubles [ 109,110]. Application of this technique to a series of Texas lignites showed contents of --(CH2)n-- of 6.53-10.52% for Wilcox Group lignites, 7.83-14.51% for Yegua Formation li gnites, and 8.05-13.89% for Manning Formation lignites (weight percent, maf basis) [ 109]. The average for ten Wilcox Group samples was 8.23%, with a standard deviation of 1.14. For Alcoa (Texas) lignite, 6.6% of the lignite is found as polymethylene groups by this technique [110]. Despite the fact that the Wilcox stretches for hundreds of miles, the uniformity of polymethylene content suggests a relatively constant paleoflora and environment of deposition over a large area [ 109]. NMR of Rockdale lignite of (fa 0.44) showed that the amount of methylene groups present as part of the macromolecular network structure of the coal is greater than that trapped in the coal as extractable fatty acids [111]. Proton NMR spectroscopy of the 3:1 benzene:methanol extracts from seven Texas lignites showed an average CH2/CH3 ratio of 3.49 [111]. (The extract yields were in the range 2.3-7.6%.) By comparison, a German brown coal treated in the same fashion yielded 3.3% extract with a CH 2/CH3 of 5.63. This difference might be attributable to a shortening of aliphatic chains with increasing maturation, or a greater amount of chain branching or methyl substituents in the Texas lignites [ 111]. In comparing these two studies [ 109,111 ] it should be borne in mind that the
107 former observes polymethylene units liberated from the macromolecular structure by breaking covalent bonds, whereas the latter is a characterization of compounds produced by solvent extraction. Supercritical toluene extracts of lignites have sharp bands at 1.3 ppm in the 1H spectra and at 29.7 ppm in the 13C spectra, assigned to methylene groups in chains containing at least eight carbon atoms [95]. The average chain length of the extracts is between 2.5 and 4 carbon atoms [95]. Aromatic structures are predominantly single-ring moieties. Brandon (Vermont) lignite shows a sharp, intense peak for aliphatic carbons indicative of material derived from algal residues [ 112]. This observation compares with results of oxidation studies which suggested the existence of material like Type I kerogen in lignite [65,107]. Two samples of Beulah-Zap lignite provided the 13C NMR data on aliphatic carbon summarized in Table 3.17 [66]. TABLE 3.17 Aliphatic carbon types in Beulah-Zap lignites* [66]. Sample Carbon type Total aliphatic carbon (fai) Aliphatic carbon as CH or CH2 (falH) CH3 or non-protonated aliphatic carbon (fai*) Aliphatic carbon bonded to oxygen (faio)
A 0.39 0.25 0.14 0.12
O 0.34 0.21 0.13 0.10
*A = sample from Argonne National Laboratory premium coal sample bank; O = non-premium sample believed to have been oxidized. (iii) Other instrumental methods. Fourier transform infrared spectroscopy (FTIR) of Bienfait lignite shows an absorption at 693 cm-1 attributed to a double bond in a side chain, or possibly in a trapped long-chain compound [ 113]. This band could also arise from substitution of dissimilar groups onto an aromatic ring [ 113]. Examination of the asymmetric C-H stretch in the FFIR spectra shows very few --CH3 bands in Beulah lignite [114]. T h e - C H 3 / - C H 2 - r a t i o increases with rank. FTIR of Titus lignite showed 4.1% by weight of aliphatic C-H, compared to 0.7% aromatic C-H (both on a dmmf basis) [85]. Secondary ion mass spectrometry (SIMS) shows that, in general, low-rank coals contain more methyl groups than higher rank coals, on the basis of comparison of intensities of the peak at 15 daltons [ 115]. The complete SIMS spectra of low-rank coals are similar to those of wood. The material considered to be amorphous in X-ray diffraction includes aliphatic side chains on aromatic ring systems, phenolic oxygen, and other functional groups [92]. The amount of amorphous material decreases with increasing carbon content. In the range of 60-70% carbon, the amorphous material decreases from about 38% of the coal to about 34% [92]. (iv) Studies of lignite extracts. Henning lignite, Seyitomer (Turkey) lignite and three British
108 bituminous coals, were studied by a series of pyrolysis and extraction methods [ 116]. Extractions were done using supercritical toluene and a hydrogen-donor solvent. After separation of the products into preasphaltenes, asphaltenes, and pentane-solubles, analysis was done using 13C NMR and GC/MS. About 30% of the total carbon in the two lignites is present as aliphatic carbon. Less than half of the aliphatic carbon is present in hydroaromatic structures or bridges between aromatic ring systems. About 20% is present as methyl groups. Alkyl chains of eight or more carbons account for about 35% of the aliphatic carbon (equivalent to 10% of all the carbon in the lignite). Long-chain n-alkanes and high-molecular-weight aliphatic acids or waxes are minor components. This suggests that many of the long aliphatic chains are bonded to aromatic structures, and contrasts with the view (e.g., [ 112]) that aromatic and long-chain aliphatic materials represent separate domains in lignite. Aliphatic structures of 23-25 carbon atoms, possibly remnants of the original plant material, have been isolated from Novodmitrovskoe (Ukrainian) lignite [ 117]. Sequential solvent extraction of Beulah-Zap lignite shows terpenoid hydrocarbons to be the major components of the extract, with tricyclic diterpenoids the most abundant [118. n-Alkanes are relatively minor components. In the range C16-C32the alkanes with odd numbers of carbon atoms predominate, with a maximum at C27 [118]. (v) Characterization of reaction products. Straight-chain hydrocarbons in the C24-C28 range were isolated from the neutral fraction of lignite low-temperature tar [33]. The largest alkyl substituent on an aromatic ring was found to be C4. The largely aromatic structures were present in a dispersed phase in an aliphatic matrix of high-molecular-weight hydrocarbons, forming a solid colloid. Additional structural integrity is provided by crosslinking in the dispersed aromatic phase and by hydrogen bonding. This structural model accounts for the existence of long-chain aliphatic molecules. Compounds making up the aliphatic matrix, which is not necessarily the major portion of the lignite structure, could derive from the waxes and resins of plant debris. A contribution of the phytyl chain from chlorophyll was also suggested [33]. Flash pyrolysis indicates that lignites may contain up to 10% polymethylene units of the type --(CH2)n-- [ 119]. Pyrolysis at 600~ drives off some of these units as alkanes or alkenes in the range C17 at least to C24 [119]. Flash pyrolysis of Alcoa lignite produced various light hydrocarbon gases, including 3.2% ethylene, 0.74% propylene, and 0.41% butadiene [120]. These products arise from polymethylene precursors having more than four --CH2-- units in the chain [120]. The amount of --(CH2)n--, where n>4, in this lignite amounted to 5.3% based on the flash pyrolysis results [ 110]. This is somewhat lower than the estimate of 6.6% obtained from NMR analysis of products of liquefaction of this lignite in tetrahydroquinoline [ 110]. Lignite liquefaction products contain a homologous series of alkanes, n-Alkanes with up to 32 carbons are obtained in yields of 3-5% (maf basis) during liquefaction with synthesis gas. Since there seems no plausible way in which these compounds could be synthesized in situ or be an artifact of the experiment, these alkanes are present in the lignite and are liberated during liquefaction [121,122].
109 Reaction of Texas lignite in pyrolysis, in hydrogen, or in the presence of a hydrogen donor solvent (tetralin) produces in each case products composed predominantly of long-chain aliphatic compounds [ 121 ]. The reaction temperatures were kept below 400~ to avoid secondary reactions of the products. The relative proportions of the alkanes from each type of experiment were essentially the same, although pyrolysis in inert gas gave the smallest yield of alkanes and reaction in tetralin the highest. The constant proportion of alkanes released in each experiment suggests that these products are indeed constituents of the lignite structure, and presumably derive from the original plant material. Soxhlet extraction of Beulah-Zap lignite with tetrahydrofuran yields cyclic and branched alkanes, diterpanoids, tetracyclic tel-panes, and pentacyclic triterpanes [ 122]. Subsequent reaction with hydrogen at or below 290~ in methanol (290~
followed by reaction in a 10% solution of potassium hydroxide
nitrogen atmosphere, 1 h) gave a product containing n-alkanes, alkyl
aromatics, and heterocyclic compounds [122].The aliphatic portion is 4.5% of the product, equivalent to 3.2% of the lignite [122]. The results indicate that alkyl groups and methylene bridges are part of the macromolecular network of the lignite. A smooth distribution of n-alkanes in the range C 12-C40 occurs, with no preference for odd- or even-numbered carbon chains. Some branched alkanes and alkenes were also observed. Dehydrogenation of vitrains has shown that 25-30% of the hydrogen content of lignites is present in hydroaromatic structures [123]. The reactions were carried out using 1% palladium dispersed on calcium carbonate as the dehydrogenation reagent in phenanthridine as the vehicle [123,124]. After depolymerization with phenol and boron trifluoride at 100~
the yield of phenol-
soluble products was proportional to the number of cleaved methylene bridges [ 125]. Lignite gave a 72.8% net yield of phenol-solubles, 2.5 to 8 times as great as yields observed from bituminous coals. 3.3 H E T E R O A T O M S
3.3.1 Introduction Oxygen is by far the most important of the heteroatoms in lignite. North American lignites can contain over 20% oxygen on an maf basis. Most of this section is a discussion of the distribution of oxygen among various functional groups. Much less is known about the organic sulfur and the nitrogen in lignites. Each accounts for about 1% of the lignite (maf basis). Few thorough investigations have been conducted on the contribution of these two elements to the structure of the lignite, or on the functional groups in which they are incorporated. 3.3.2 Carboxylic acid groups The carboxylic acid group is one of the most important of the oxygen-containing groups in lignites. In North Dakota lignites up to 65% of the oxygen occurs in these groups [ 126]. However,
110 this value is quite high compared to most of the measurements reported in the recent literature. A Beulah-Zap lignite in which the total organic oxygen content was 17.21% (dry basis), as measured by neutron activation analysis, contains 3.81-3.94% oxygen as carboxyl oxygen [127]. This is equivalent to 22-23% of the total oxygen being present in carboxyl groups. A value of 18% was observed for Estevan lignite vacuum-dried at 100*C [128]. Some estimates give values even lower, 10-13% of the oxygen as carboxyl, for example [129]. The carboxylic acid group is labile under mild thermal conditions, decomposing to carbon dioxide well below 500* C. Although the volatile matter content of lignites is higher than of bituminous coals, much of the material lost from lignite as volatiles is carbon dioxide rather than hydrocarbon gases, oils, or tars. Thus only about 17% of the calorific yield of North Dakota lignite occurs in the volatile products whereas about 30% occurs in the volatiles from bituminous coals [ 130]. The ability of the acid groups to bind cations on ion exchange sites is important in the inorganic chemistry of lignites (Chapter 5). A carboxyl-metal cation-carboxyl linkage may also have a role in crosslinking of the lignite structure [89]. A general procedure for the determination of carboxylic acid groups has been developed [131,132]. The basis of the method is that the carboxyl groups, which have all been put into the acid form by a preliminary demineralization step, are reacted with barium acetate solution. Barium ions displace acidic protons from the carboxyl groups. Titration of the now-acidic solution with standard base determines the quantity of protons released, equivalent to the number of acidic functional groups in the coal. Experimentation with several variations of the general method led to the recommendation of a single reflux of 4 h with barium acetate at pH 8.25 followed by titration of the acetic acid formed as the most reliable method [131]. North Dakota and Texas lignites contain 2.2-2.3 meq/g (dmmf) carboxyl [131]. Total acid group contents (i.e., carboxyl plus phenolic hydroxyl) range from 7.5 for a South Dakota lignite and 6.9 for a North Dakota lignite, to 6.1 for a Texas lignite, all reported as meq/g, dry basis [132]. Demineralization preliminary to the determination of carboxyl groups involves reaction with 5M hydrochloric acid, concentrated hydrofluoric acid, and then concentrated hydrochloric acid, all at 55--60~ for 1 hour, followed by extensive washing with distilled, CO2-free water [133]. The carboxyl content can then be determined by reaction with 1N barium acetate at pH 8.25-8.30, followed by titration with 0.05N barium hydroxide to restore the pH to the initial value [ 133]. Carboxyl contents of various lignites are shown in Table 3.18. The percentage of the total oxygen content of the coal incorporated in the carboxyl groups is also given, when that information was provided in the original literature. A modification to the barium-exchange method involves ion exchange with barium chloride solution at pH 8.3 in a blender under a nitrogen, followed by titration [75]. For Big Brown lignite, the carboxyl content was found by this method to be 3.6 meq/g (maf basis). Data for Beulah lignite highlight the variability of carboxyl content [23,134,135,138]. Six samples show carboxyl contents ranging from 1.46 to 2.97 meq/g with a median value of 2.31 meq/g. Four samples identified as "Seam 2" Beulah lignite ranged from 2.25 to 3.67 meq/g, with a median of 2.72. It is likely that some of the spread in the data may be accounted for by variations
111 TABLE 3.18 Carboxylic acid contents for lignites Source of lignite Carboxyl State Seam or Mine meq/~ (dmmt) Alabama Choctaw 2.83 Alabama Pike County 2.04 Montana Fort Union 3.00 N. Dakota Baukol Noonan 2.74 N. Dakota Beulah 2.78 N. Dakota Beulah 2.30 N. Dakota Center 3.58 N. Dakota Freedom 2.60 N. Dakota Gascoyne Blue 2.68 N. Dakota Gascoyne Red 2.46 N. Dakota Gascoyne White 2.62 N. Dakota Gascoyne Yell. 2.67 N. Dakota Hagel 3.13 N. Dakota Indian Head 2.45 N. Dakota Kincaid 2.89 N. Dakota (unident.) 2.2 N. Dakota Velva 2.55 Texas Big Brown 2.26 Texas Bryan 2.25 Texas Darco 2.11 Texas Ledbetter 1.82 Texas San Miguel 1.4 Texas (unident.) 2.3 (unident) 1.1
Percent of oxygen 42 38
46
37
Ref. [ 134,135] [134,135] [133, 136,137] [134,135] [138] [23] [134,135] [139] [138] [26] [26] [138] [133,136,137] [134,135] [33] [131] [134,135] [ 134,135] [134,135] [ 133,136,137] [ 134,135] [ 134] [ 131 ] [ 138]
in experimental technique; furthermore, no information was provided on how long the samples might have been exposed to air or on the petrographic composition of the samples. (The carboxyl contents of vitrain and fusain from Beulah lignite are 2.28 and 2.49 meq/g, respectively [140], and attritus, 2.83 meq/g [139].) Nevertheless, the carboxyl content likely varies within a seam. Certainly the amount of inorganic material in the lignite, including the ion-exchangeable cations (Chapter 5) varies throughout the seam. The variation in carboxyl content may relate directly to the observed variation in inorganic composition. Values for two samples of Gascoyne "Blue Pit" lignite are 2.71 and 2.90 meq/g; for two samples of "Red Pit" lignite, 2.46 and 2.57 meq/g [26]. (These designations refer to different working pits within the mine.) The data for Gascoyne lignite in Table 3.18 also indicate how carboxyl content may vary from one working pit to another within the same mine. The total oxygen incorporated in carboxyl groups for three lignites [ 136] is lower than the reported maximum of 65% of total oxygen incorporated as carboxyl groups [ 126]. For these three samples, the percentage of carbon in the carboxyl groups are 7.6% for Hagel, 3.4% for Darco (Texas), and 5.2% for Montana lignite [133]. Approximately 50% of the total surface area measured by CO2 adsorption is covered with carboxyl groups, of which about half are in the
112 cationic form [137,141]. Acidic hydrogen in six Texas lignites was determined by introducing a pulverized sample into a solution of lithium aluminum hydride in diethyl ether, and measuring the total volume of hydrogen gas evolved. This method will liberate hydrogen attached to any group acidic enough to react with lithium aluminum hydride; thus it does not differentiate between carboxyl and hydroxyl groups. Active hydrogen ranged from 1.52 to 2.77 meq/g (daf basis), averaging 2.22 meq/g [111]. Assuming that the active hydrogen represents 2.22 meq/g of carboxyl, this carboxyl content is equivalent to 71 mg/g of oxygen, or about 7.1%. The total oxygen content of these six samples, as determined by neutron activation analysis, was 26.09%-36.15% [111]. Thus a significant fraction, roughly four-fifths, of the oxygen in these lignites must be present in carbonyl, methoxyl, and other ether groups. The reaction of lignite with sulfur tetrafluoride has been suggested as a method for determining carboxyl groups [ 142]. Carboxyl groups are converted to acyl fluorides, which can then be determined by high-resolution solid-state NMR. IR evidence exists for the conversion of --COOH to --COF by reaction with sulfur tetrafluoride at 110~ for 1 h [143]. The FFIR spectrum of Beulah lignite shows a major band at 1562 cm-1, assigned to carboxylate groups [114]. Major bands at 1655 and 1520 cm-1 in the spectrum of Beulah-Zap lignite are assigned to conjugated carbonyl and carboxyl groups [ 114]. A concern about reliance on the barium-exchange method for carboxyl determination is that the exchange reaction might not be complete, and therefore the results might underestimate the total quantity of carboxyl [144]. Conversion factors have been developed to relate the intensity or area of the 1700 cm-1 FFIR peak to the percentage of oxygen in the sample present as --COOH [144]. X-ray photoelectron spectroscopy of Beulah lignite, using poly(ethylene terephthalate) as a calibration standard, estimated the molar ratio of carboxylate to all C-O single bonds to be 0.625 [23]. The spectroscopic data could not be refined to distinguish between phenolic and ether C-O. Little work has been done on applying XPS to oxygen functional group analysis of lignites. However, this result is high relative to the ratio of [-COOH]/{[-C-OH] + I-C-O-C-]} calculated from data obtained from other methods. The value of this ratio is 0.33 for a Beulah-Zap lignite calculated from the data in [127], and 0.40 calculated from the data in [128]. Ruthenium tetroxide oxidation provides information on the structural arrangement of carboxyl groups [97]. The products include three tricarboxylic acids, oxalomalonic (17), 7.7% of the organic products of the reaction; oxalosuccinic (18), 3.2%; and oxaloglutaric (19), 1%. The benzoic, phenylacetic, and phenylpropionic acid structures of this lignite are in the proportion 65:27:8. Oxidation of Beulah lignite methylated with methyl-d3 iodide indicates that about 10% of the aliphatic diacids produced in the reaction derive from arylalkanoic acids such as 3arylpropanoic acid [59]. This result indicates that at least some of the carboxyl groups in lignite are at the ends of aliphatic chains connected to aromatic rings. The 1600 cm-1 band in the Raman spectrum (assigned to the E2g mode of a graphite-like structure) of two Beulah lignites differing in carboxyl contents is less intense in the sample of higher carboxyl content [23]. This suggests that
113 HOOC CHCOOH I CO I COOH 17
HOOCCHCH 2COOH I CO I COOH 18
HOOCCH ,,CHCH 2COOH "1 CO I COOH 19
the steric requirements of the relatively bulky carboxyl groups, with their associated cationic counterions, may prevent alignment of aromatic ring systems, affecting long-range structural order in the lignite. Fatty acids have been isolated from lignites [145]. In contrast to modern biological systems, in which fatty acids with even numbers of carbon atoms predominate, the isolated acids include ones with odd numbers of carbon atoms [145]. Microbes may preferentially use the evennumbered acids, so that even if they far exceed those with odd-numbered chains in modern systems, microbial consumption of the even-numbered chains increases the proportion of oddnumbered acids among the total [ 146]. Waxes isolated from lignites also contain both even- and odd-numbered fatty acids and alcohols [145]. Acidic fractions isolated by sequential extraction of Beulah-Zap lignite consist mainly of even-numbered acids in the range C22-C30, with a maximum at C26 [118]. Field ionization mass spectrometry signals from Beulah-Zap lignite also demonstrate the existence of fatty acids [147]. 3.3.3 Humic acids Extraction of fresh lignite with dilute aqueous alkali yields 2-4% of so-called natural humic acids [33]. Up to 90% of the original dry, ash free organic material can be extracted from Dow (Texas) lignite after reaction with 0.25N sodium hydroxide solution for 5 h at 433 K [148]. Extraction of German brown coals with 1% ammonia, followed by precipitation with HCI, yields 0.5-3% humic acids [ 149]. Since mild atmospheric oxidation of the base-extracted residue yields more humic acids on repeated extraction, it is not clear whether the natural humic acids were present in the lignite or formed as a result of initial oxidation as soon as the lignite is first exposed to the atmosphere. Nevertheless the extracted humic acids represent only a minor modification of the lignite structure. Lignites can be converted to sodium humates by high speed blending in aqueous sodium hydroxide [150]. The yield increases in the presence of small amounts of air (i.e., air leaking into the apparatus--a kitchen blender--which had initially been purged with nitrogen). Humic acids from Big Brown and Beulah lignites and Wyodak (Wyoming) subbituminous coal show similar aromatic/aliphatic peak intensity ratios in 13C NMR spectra, suggesting similarities in the chemical nature of the acids. High speed blending (about 24,000 rpm) of Beulah lignite in 5% aqueous sodium hydroxide gave 89% conversion to humic acids. The acids had a weight-average molecular weight of 4.3 x 105. The weight-average molecular weight is inversely proportional to the rotational speed
114 of the blending, suggesting that higher shear rates effect greater disruption of the coal structure, giving higher yields of a lower molecular weight product. The effect of blending conditions on Russian low-rank coals has been demonstrated [151]; amorphous humic acids are recovered, but the properties of the products depend on the conditions of blending (i.e., choice of reagents, and use of an air or inert atmosphere). Very low conversions were obtained when the reaction was attempted with 30% aqueous ammonia (12%) or with pyridine (8%), suggesting that the liberation of humic acids is neither the result of cleavage of hydrogen bonds nor of ester hydrolysis [ 150]. Humic acids isolated by high speed blending of Beulah lignite in nitrogen have a composition of 67.5% C, 4.2% H, 0.86% N, and 26.7% O (maf basis) [150]. The inorganic content of the humic acid is also low, reported as 0.83% ash [ 150]. The integrated peak intensity for the carboxyl carbons in the 13C NMR spectrum was about 11% of the total integrated intensity. Some differences in the elemental composition and the carboxyl content are observed depending on the specific isolation technique. Blending Big Brown lignite with 5% sodium hydroxide gave a 81% yield of a humate latex [75]. The humic acids were more aromatic than the original lignite. The molecular weights of reduced, methylated derivatives of the acids were 1,300,000, similar to humic acids from North Dakota lignites. (Humic acid extracted from Beulah lignite had a molecular weight of 1,300,000, as measured by low angle laser light scattering [ 152].) Alkaline digestion of Australian brown coal results from disruption of the structure by electrical double layer repulsion and migration of water molecules into the hydrogen-bonded gel structure of the coal [153]. The mechanism involves interaction of hydroxide with the acidic functional groups, followed by chemisorption of alkali metal cations by the coal structure. 3.3.4 Methoxyl groups Arylmethoxyl groups are important in the structure of North Dakota lignite, but may be insignificant in Wyoming lignite [103]. Oxidation of North Dakota lignite with peroxytrifluoroacetic acid indicated that about 15% of the total hydrogen was present in arylmethoxyl groups, comparable to lignin [103]. This oxidation converts arylmethoxyls to methyl trifluoroacetate, which was measured by NMR. A simplified methoxyl determination involves refluxing lignite in concentrated sulfuric acid, followed by distillation and gas chromatographic measurement of the liberated methanol in the distillate [102], a value of 0.71% being found for Indian Head (North Dakota) lignite [154]. Kincaid (North Dakota) lignite has a methoxyl content of 0.90%, or 0.29 meq/g, as determined using the Zeisel method [33]. The methoxyl content of Indian Head lignite was determined to be 0.7% (as-received basis) by oxidation with peroxytrifluoroacetic acid, followed by hydrolysis of the methyl ester products and gas chromatographic measurement of the liberated methanol [155]. This gives quite good agreement with the method using sulfuric acid reaction [102]. The methoxyl groups are very labile in hot water drying (Chapter 10) and extraction with supercritical water. The methanol yield during
115 hot water drying of the same lignite at 325~ was 0.5%, and during supercritical water extraction at 390"C, 0.6% (as-received basis) [ 155]. Oxidative degradation with sodium periodate is specific for o-methoxyphenols (the products are methanol and o-benzoquinone). Determination of the methanol provides a measure of guaiacol groups not etherified at the 4-0 position. This procedure applied to Beulah lignite showed at least a third of the methoxyl groups present in free guaiacol structures [3,155]. A similar proportion is observed in sodium periodate oxidation of wood [ 155]. Under reflux, the methanol yield increases from 0.25 to 0.44% (as-received basis), due either to the depolymerization of the lignite structure making more guaiacol groups accessible to periodate, or to hydrolysis of omethoxyphenyl linkages generating new guaiacol units [155]. The methoxyl contents of Beulah lignite lithotypes, determined by the peroxytrifluoroacetic method, were 1.3% for the vitrain and 0.7% for attritus (maf basis) [3]. The composite sample
(i.e., not separated into lithotypes) contained 1.3%. A value of 1.8% (maf basis) has also been reported for methoxyl in Beulah vitrain [156]. Methoxyhydroxybenzene structures in the vitrinitic components of lignite derive from fossil lignin moieties [ 147]. Fusain contains 1.1% methoxy on an as-received basis [155]. A composite sample of Indian Head lignite treated in a similar manner had 1.2% methoxyl. The methoxyl content, determined by this method, for a coalified tree stump from the Beulah mine was found to be 0.2% on an as-received basis [ 155]. (Fusain also had the highest amount of residual cellulose, discussed below. Whatever geochemical process interrupted the degradation of cellulose also interrupted lignin degradation. The low value obtained for the coalified tree stump may reflect an easier access of fungal enzymes to the isolated stump than to highly compressed lignite in the interior of a seam.) Potassium permanganate oxidation of sporinite, followed by methylation of the products with dimethyl sulfate-d6, produces both methoxy-d3- and methoxybenzenecarboxylic acids [157]. This confirms the existence of both hydroxy- and methoxybenzene structures in sporinite. 3.3.5 Phenolic groups Many of the aromatic tings in lignites have an --OH group, and some have either a second --OH group or one or two methoxyl groups [158]. Beulah-Zap lignite contains 9.16% oxygen (dry basis) as phenolic oxygen, amounting to 53% of the total organic oxygen in the sample [ 127]. For Estevan lignite, the corresponding data are 7.2% and 38%, respectively [128]. A phenolic content of 2.97 meq/g has been determined in Kincaid lignite [33]. Extraction of Estevan lignite with benzene at 4.8 MPa (approximately 280~
for 3-10 days
gave an extract separable into acidic and non-acidic portions by treatment with 5% aqueous potassium hydroxide. Phenols were liberated by acidification and subsequently identified as their brominated derivatives. The total phenolic content of this lignite was 2.55%, the principal phenols being phenol, p-cresol, and catechol [55]. The same phenols, in the same proportion, were extracted from Morwell (Victoria, Australia) brown coal. Extraction of mono- and dihydric phenols from lignite with benzene suggested that the phenols exist as such in the lignite, either as free
116 phenols or in some weakly bonded association [33]. The yield of phenols increases with increasing pressure at least to 280~ [33]. Extractions at high temperature are ambiguous in that one is not sure whether the increased yield is due to improved extraction of species already existing in the lignite or is due to species liberated by thermal decomposition. In this case, 280 ~was presumed to be below the onset of thermal decomposition. Reaction with triethylborane has been proposed as a means of determining hydroxyl groups [ 159]. The reagent reacts with hydroxyl groups to form the O-diethylborylate and liberate ethane. The ethane can be determined volumetrically. No data on North American lignites have been published, but for three German brown coals containing 67% carbon and 26-27% oxygen (daf basis) the hydroxyl contents determined by O-diethylborylation ranged from 6.20 to 7.83 mmol/g, equivalent to the incorporation of 36 to 46% of the total oxygen in hydroxyl groups [ 159]. This is in reasonable agreement with results mentioned above, but obtained by greatly different methods, for Beulah-Zap [ 127] and Estevan [128] lignites. Potassium permanganate oxidation of sporinite from North Dakota lignite and methylation of the oxidation products with dimethyl-d6 sulfate produced a mixture of methoxy-d3 and natural methoxybenzenecarboxylic acids [57,157]. This indicates that the aromatic units contain both phenolic and methoxyl functional groups. GC-MS analysis of the product mixture indicates that the phenolic groups are more prevalent than the methoxy by a factor of about 9.4 [57]. 3.3.6 Carbonyl groups The carbonyl oxygen content of Kincaid lignite was determined to be 4.4% (maf basis) [33], equivalent to 2.7 meq/g of oxygen in ketone, quinone, and aldehyde groups. Beulah-Zap lignite contains 1.96% oxygen in carbonyl structures, equivalent to 11% of the total organic oxygen [ 127]. Results for Estevan lignite are somewhat higher, 3.6% oxygen in carbonyl groups, or 19% of the total oxygen [128]. NMR of Estevan lignite suggests 29-32% of the structural groups in the coal contain C=O structures [39], presumably including carbonyl and carboxyl. The existence of carbonyls in Beulah lignite has been suggested on the basis of the band at 1655 cm-1 in the FFIR spectrum [114]. 3.3.7 Ethers other than methoxyl Ethers in Beulah-Zap lignite, estimated by difference after determination of carboxyl, carbonyl, and phenolic groups, account for 2.28% oxygen, or about 13% of all the oxygen in the lignite [ 127]. The comparable figure for Estevan lignite is 25% of the total oxygen in "residual" oxygen functional groups [ 128]. 4-Nitroperbenzoic acid cleaves benzyl ethers [160]. Benzyl ether linkages are an important component of lignin structures and may persist from the lignin into coals. Reaction of Beulah lignite with 4-nitroperbenzoic acid in refluxing chloroform, followed by extraction of the residue with base, gave yields of humic acids of up to 90% (maf basis) [152,161]. The soluble material resembled the waxy material removed from lignite by solvent extraction prior to oxidation.
117 Cleavage of benzyl ether crosslinks generated base-soluble carboxylic acid or phenolic functional groups. (This reaction could involve other structural featrues which are reactive toward 4nitroperbenzoic acid; carbon bridges between aromatic units, as in diphenylmethane, are unreactive, but phenanthrene and anthracene structures could be oxidized at least as far as quinones.) The molecular weight of the base-soluble product was determined by low angle laser light scattering to be 1,300,000 [152,161], comparable to that of humic acids extracted directly from the lignite by base. Thus oxidative cleavage of benzyl ethers releases structural units of very large size, comparable to humic acids. Since the yield is much larger from the 4-nitroperbenzoic acid oxidation than from base extraction without prior oxidation, the results imply that large macromolecular humic acid-like structural units are present in the lignite, held in place by benzyl ether groups. Reaction with phenol and boron trifluoride, a reagent pair well known to depolymerize coal [ 125], showed that lignite produced the highest yield (75%) of phenol-soluble products of any of the ranks of coal tested [ 162]. Substitution of p-toluenesulfonic acid (pTSA) for boron trifluoride converted over 90% of low-rank coals to pyridine-soluble products [162]. For lignites, a major contribution to this extensive depolymerization is cleavage of aliphatic and benzyl ethers. Extensive depolymerization of lignite in these reagents suggests the presence of abundant ether linkages. However, aliphatic bridges linked to single phenolic rings are also reactive enough to participate in depolymerization by phenol-BF3 or phenol-pTSA. The well-known ability of aqueous alkali to solubilize large amounts of lignite has been attributed to the cleavage of ether linkages [163]. The benzyl aryl ethers of the 1~-O-4, ~x-O-4, andy0-4 type appear to be especially labile. (The structural notation for lignin is given on page 70.) The reaction occurring upon blending lignite in aqueous sodium hydroxide proceeds by base-catalyzed guaiacol ether cleavage similar to the alkaline pulping of lignin. Humic acids have been isolated from brown coals by treatment with sodium in liquid ammonia [ 164], a reagent sufficiently basic to convert ethers to alkenes [165]. Benzyl ethers in lignin-derived structures may be sterically hindered, and thus high base concentrations and high shear rates may be important in breaking the lignite structure down to colloidal dimensions. Humic acid derivatives obtained by high speed blending have a weight average molecular weight of 4.3 x 105, lower by a factor of two than obtained by medium-speed blending, and lower by a factor of three compared to magnetic stirring [150]. The yield was highest after high-speed blending. The more severe blending breaks more crosslinks in the lignite structure, giving a humic acid yield that is higher but in fragments of lower molecular weight. Oxidation of Sheridan lignite with potassium permanganate forms, among many other acids, furan-, benzofuran-, dibenzofuran-, and xanthonecarboxylic acids, indicating the presence of some oxygen in heterocyclic ring structures [ 108]. Oxidation with sodium dichromate at 2.50~ for 36-40 h produced cyclic ethers having the following approximate relative abundances: benzofuran (20), 7%; isochroman (21), 2.5%; dibenzodioxane (22), 2%; xanthone (23), 17%; benzoxanthone (24), 1%; and dibenzofuran (25), 2.5% [52]. Some oxidation studies suggest that
118
20
21 O
23
22 O
24
25
the contribution of cyclic structures such as furan, 20, 23, and 25 is minor [50]. Reactions of Texas lignites with mixed carboxylic-sulfonic acid anhydrides indicate that few ether linkages occur [ 111]. 3.3.8 Ester groups Little seems to be known about the contribution of esters to lignite structure, although there seems to be a consensus that these groups are not of great importance. Reaction of Beulah lignite with sodium methoxide in methanol produced a waxy material with no spectroscopic evidence of incorporation of methoxide into the residue, indicating that no transesterification with methoxide had occurred. This observation suggests that esters are probably not an important component of the structure of lignite [150]. Some mono- esters and aromatic di-esters have been observed in BeulahZap lignite by field ionization mass spectrometry [ 147]. 3.3.9 Cellulose and lignin residues Plant lignin is first concentrated, and then modified, in the conversion to lignite [166]. Formation of methanol during pyrolysis indicates the presence of guaiacol units [3]. They may be present as plant lignin that has survived coalification as relatively unaltered lignin substructures, or as isolated guaiacols liberated by a decomposition process that did not affect the methoxy or side chain carbons. Since thermal alteration of lignins generally involves loss of methoxy and conversion of side chains to ketones or carboxylic acids, it seems more likely that relatively unaltered lignin is present. Guaiacol, 4-methylguaiacol, 6-methylguaiacol, 4-ethylguaiacol, and 4propylguaiacol have been identified as pyrolysis by-products in the gasification of lignite [167]. (Examples of several of these structures are shown in Chapter 2.) Lignin-like polymers are an important component of the structure of low-rank coals. Oxidation of low-rank coals with alkaline copper(II) oxide produced large quantities of p-hydroxybenzoic acid, 3,4-dihydroxybenzoic acid, and 4-hydroxybenzenedicarboxylic aci