COMPREHENSIVE ANALYTICAL CHEMISTRY VOLUME
53
Elsevier Radarweg 29, PO Box 211, 1000 AE Amsterdam, The Netherlands Linacre House, Jordan Hill, Oxford OX2 8DP, UK
First edition 2008 Copyright r 2008 Elsevier B.V. All rights reserved No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, mechanical, photocopying, recording or otherwise without the prior written permission of the publisher Permissions may be sought directly from Elsevier’s Science & Technology Rights Department in Oxford, UK: phone (+44) (0) 1865 843830; fax (+44) (0) 1865 853333; email:
[email protected]. Alternatively you can submit your request online by visiting the Elsevier web site at http:// www.elsevier.com/locate/permissions, and selecting Obtaining permission to use Elsevier material Notice No responsibility is assumed by the publisher for any injury and/or damage to persons or property as a matter of products liability, negligence or otherwise, or from any use or operation of any methods, products, instructions or ideas contained in the material herein. Because of rapid advances in the medical sciences, in particular, independent verification of diagnoses and drug dosages should be made British Library Cataloguing in Publication Data A catalogue record for this book is available from the British Library Library of Congress Cataloging-in-Publication Data A catalog record for this book is available from the Library of Congress ISBN: 978-0-444-53056-1 ISSN: 0166-526X
For information on all Elsevier publications visit our website at books.elsevier.com
Printed and bound in Hungary 08 09 10 11 12 10 9 8 7 6 5 4 3 2 1
ADVISORY BOARD Joseph A. Caruso University of Cincinnati, Cincinnati, OH, USA Hendrik Emons Joint Research Centre, Geel, Belgium Gary Hieftje Indiana University, Bloomington, IN, USA Kiyokatsu Jinno Toyohashi University of Technology, Toyohashi, Japan Uwe Karst University of Mu¨nster, Mu¨nster, Germany Gyo¨rgy Marko-Varga AstraZeneca, Lund, Sweden Janusz Pawliszyn University of Waterloo, Waterloo, Ont., Canada Susan Richardson US Environmental Protection Agency, Athens, GA, USA
Wilson & Wilson’s
COMPREHENSIVE ANALYTICAL CHEMISTRY
Edited by ´ D. BARCELO Research Professor Department of Environmental Chemistry IIQAB-CSIC Jordi Girona 18-26 08034 Barcelona Spain
Wilson & Wilson’s
COMPREHENSIVE ANALYTICAL CHEMISTRY MOLECULAR CHARACTERIZATION AND ANALYSIS OF POLYMERS
VOLUME
53 Edited by JOHN M. CHALMERS VS Consulting, 14 Croft Hills, Tame Bridge, Stokesley TS9 5NW, UK PROF. Dr ROBERT J. MEIER Institut fu¨r Agrosphere, ICG-4, Forschungszentrum Ju¨lich GmbH, D-52425 Ju¨lich, Germany
Amsterdam Boston Heidelberg London New York Oxford Paris San Diego San Francisco Singapore Sydney Tokyo
This page intentionally left blank
CONTENT S
Contributors to Volume 53 Volumes in the Series Preface Series Editor’s Preface
xiii xv xix xxi SECTION I: INTRODUCTION
1. Introduction
3
John M. Chalmers and Robert J. Meier 1. The Analytical Competence 2. Contents and Structure 3. Practical Considerations in the Multi-Technique Approach References
2. Polymer Chemistry and Microstructure
3 6 11 12
13
Jacques Devaux and Sophie Demoustier-Champagne 1. Introduction 2. Polymer: Definitions 3. From Molecules to Macromolecules 4. Fundamentals of Polymer Chemistry 5. Polymer Degradation 6. Summary References
3. Polymeric Materials: Composition, Uses and Applications
14 15 25 34 58 62 62
65
J.P. Candlin 1. Introduction 2. Mode of Polymerisation 3. Polymer Materials: Types and Forms 4. Polymer Additives 5. Summary Bibliography
65 66 68 87 117 118
vii
viii
Contents
SECTION II: POLYMER CHAIN ANALYSIS
4. Chain Structure Characterization
123
Gregory Beaucage and Amit S. Kulkarni 1. Introduction to Structure in Synthetic Macromolecules 2. Local Structure and Its Ramifications 3. Summary References
5. Chain End Characterisation
123 134 165 166
171
Anthony T. Jackson and Duncan F. Robertson 1. 2. 3. 4.
Introduction End Groups in Free Radical Polymers End Groups in Condensation Polymers End Groups in Polymers from Ionic Polymerisation 5. Closing Remarks Acknowledgements References
6. Determination of Molecular Weights and Their Distributions
171 175 182 194 201 201 201
205
Simone Wiegand and Werner Ko¨hler 1. Introduction 2. Distribution Functions and Averages 3. Methods Based on Colligative Properties 4. Viscometry 5. Scattering Techniques 6. Liquid Chromatography 7. Analytical Ultracentrifuge 8. Other Methods 9. Practical Examples 10. Conclusion Acknowledgements References
205 208 212 218 220 228 235 237 241 247 248 248
SECTION III: POLYMER MORPHOLOGY AND STRUCTURE 7. Phase Structure and Morphology
255
Rufina G. Alamo 1. Phase Structure and Morphology 2. Supermolecular Morphology
255 274
Contents
3. Concluding Remarks Acknowledgements References
8. Characterization of Molecular Orientation
ix
286 287 287
295
Thierry Lefe`vre, Christian Pellerin and Michel Pe´zolet 1. Introduction 2. Theory 3. Birefringence 4. Infrared Linear Dichroism (IRLD) 5. Raman Spectroscopy and Microspectroscopy 6. Fluorescence Spectroscopy 7. NMR Spectroscopy 8. X-Ray Diffraction and Absorption 9. Conclusion References
9. Polymer Networks: Elastomers
295 297 301 305 313 322 325 328 333 333
337
B. Erman and J.E. Mark 1. 2. 3. 4. 5. 6. 7.
Introduction Structure of a Typical Network Elementary and More Advanced Molecular Theories Phenomenological Theories Some Relevant Simulations Swelling of Networks and Responsive Gels Enthalpic and Entropic Contributions to Rubber Elasticity: The Force–Temperature Relations 8. Multimodal Elastomers 9. Liquid–Crystalline Elastomers 10. Novel Reinforced Elastomers 11. Further Comments on Some Characterization Techniques Acknowledgement References
338 339 341 351 352 356 358 359 365 370 374 376 377
SECTION IV: POLYMER DEGRADATION 10. Polymer Degradation and Oxidation: An Introduction
387
John M. Chalmers and Robert J. Meier 1. Introduction 2. Standard Tests and Comparative Methods 3. Spectroscopic Techniques 4. Thermal Methods 5. Chromatographic Analysis 6. Closing Remarks Acknowledgement References
388 390 402 436 442 447 448 448
x
Contents
11. The Role of Oxidation in Degradation of Polymers: The Relation of Oxidation to the Light Emission from Oxidized Polymers
451
Jozef Rychly´ and Lyda Matisova´-Rychla´ 1. Introduction, Historical Overview and Terminology Associated with the Degradation and Ageing of Polymers 2. Methodology and Analytical Techniques in Polymer Stability Studies 3. Mechanisms Leading to the Light Emission from Thermally Oxidized Polymers (Chemiluminescence), Similarities and Differences within Respective Groups of Polymers 4. General Classification of Chemiluminescence from Polymers 5. Comparison of Chemiluminescence for Isothermal and Non-Isothermal Conditions with those Obtained by DSC 6. The Effect of Initial Molar Mass on Chemiluminescence Runs 7. The Effect of Temperature on Chemiluminescence Intensity; The Mutual Relation of Isothermal and Non-Isothermal Studies 8. Relaxation Experiments (Jump Changes of Concentration of Oxygen, Temperature and Humidity) and Rate Constants of Respective Elementary Reaction Steps 9. The Effect of Antioxidants and Polymer Stabilizers 10. Isothermal Kinetics of Polymers Oxidation and Its Relation to the Concentration of Oxygen in Surrounding Atmosphere 11. The Effect of Alkaline Additives on Chemiluminescence Runs: A Possible Impact 12. Conclusions and Outline of the Further Perspectives Acknowledgements References
12. ESR and ESR Imaging Methods for the Study of Oxidative Polymer Degradation
452 461
463 471 476 478 480
482 483 487 490 493 496 496
499
Shulamith Schlick and Krzysztof Krucza"a 1. 2. 3. 4.
Introduction: Polymer Degradation in the Presence of Oxygen Fundamentals of ESR and ESR Imaging ESR as a Tool for the Study of Polymer Degradation ESR Imaging: A Nondestructive Method for Spatially Resolved Polymer Degradation 5. Concluding Remarks Acknowledgements References
500 504 513 517 521 521 522
SECTION V: POLYMER PRODUCT ANALYSIS 13. Spatial Imaging/Heterogeneity
527
Peter Wilhelm and Boril Chernev 1. Introduction 2. Raman and FTIR Microscopy
527 529
Contents
3. Examples of Heterogeneous Polymers Investigated by IR and Raman Microscopy 4. Other Methods and Comparison of Methods 5. Conclusions References
14. Additive Analysis
xi
538 550 557 558
561
John Sidwell 1. Introduction 2. Analytical Techniques for Additive Analysis 3. Analysis of Specific Additives 4. Future Developments in Analytical Methodology References
15. Failure, Defect, and Contaminant Analysis
562 563 573 603 605
607
James D. Rancourt, Jennifer Brooks, Sue Mecham, Alan Sentman, Brian Starr and Jason Todd 1. Introduction 2. Case Studies 3. Summary References
607 608 673 674
16. Surface Analysis
675
John M. Chalmers and Robert J. Meier 1. Introduction 2. A Surface and Spatial Resolution 3. Adhesion 4. Polymer Degradation 5. Polymer Fracture 6. Characterizing Polymer Surfaces 7. Delamination 8. Cure 9. Closing Remark References
675 676 677 679 679 679 679 681 682 682
SECTION VI: POLYMER AND POLYMER PRODUCT DEVELOPMENT: SUPPORT TECHNIQUES 17. The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
685
John Kendrick 1. 2. 3. 4.
Introduction Methodologies Infrared and Raman Spectroscopy Photoelectron Spectroscopy and Auger Electron Spectroscopy (AES)
686 687 693 703
xii
Contents
5. Mass Spectrometry 6. X-Ray Diffraction 7. Nuclear Magnetic Resonance 8. Electron Spin Resonance 9. Summary References
18. High-Throughput Analysis
712 718 722 727 729 730
735
Robert J. Meier 1. Introduction 2. Some General Considerations on MTE and the Corresponding Analytical Needs 3. Analytical Techniques for Medium-Throughput Polymer Analysis 4. Outlook References
Subject Index See Color Plate Section at the End of This Book
735 737 740 742 743
745
CONTRIBUTORS TO VOLUME 53 Rufina G. Alamo FAMU/FSU College of Engineering, Department of Chemical and Biomedical Engineering, 2525 Pottsdamer St., Tallahassee FL 32310, USA Gregory Beaucage Department of Chemical and Materials Engineering, University of Cincinnati, Mail location 12, Cincinnati, OH, 45221-0112, USA Jennifer Brooks Polymer Solutions Incorporated, 2903C Commerce Street, Blacksburg, Virginia 24060, USA J.P. Candlin 4 Rudby Lea, Hutton Rudby, Yarm, TS15 0JZ, UK John M. Chalmers VS Consulting, 14 Croft Hills, Tame Bridge, Stokesley, TS9 5NW, UK Boril Chernev Centre for Electron Microscopy and Nanoanalysis, Steyrergasse 17, A-8010 Graz, Austria Sophie Demoustier-Champagne Universite´ catholique de Louvain, Unite´ de Chimie et de Physique des Hauts polyme`res (POLY), Croix du Sud, 1. B-1348 Louvain-la-Neuve, Belgium Jacques Devaux Universite´ catholique de Louvain, Unite´ de Chimie et de Physique des Hauts polyme`res (POLY), Croix du Sud, 1. B-1348 Louvain-la-Neuve, Belgium B. Erman Department of Chemical and Biological Engineering, Koc University, Rumeli Feneri Yolu 34450 Istanbul, Turkey Anthony T. Jackson AkzoNobel CARG, 137 Jiangtian East Road, Songjiang Industrial Estate, Shanghai 201600, P.R. China John Kendrick Institute of Pharmaceutical Innovation, Bradford University, BD7 1DP, UK Werner Ko¨hler Physikalisches Institut, Universita¨t Bayreuth, D-95440 Bayreuth, Germany Krzysztof Krucza"a Faculty of Chemistry, Jagiellonian University, 30-060 Krakow, Poland Amit S. Kulkarni Department of Chemical and Materials Engineering, University of Cincinnati, Mail location 12, Cincinnati, OH 45221-0112, USA
xiii
xiv
Contributors to Volume 53
Thierry Lefe`vre De´partement de chimie, Universite´ Laval, Que´bec, QC, G1V 0A6, Canada J.E. Mark Department of Chemistry, Crosley Tower, Martin Luther King Drive, University of Cincinnati, Cincinnati, OH 45221-0172, USA Lyda Matisova´-Rychla´ Polymer Institute, Centre of Excellence for Degradation of Biopolymers, the Slovak Academy of Sciences, 842 36 Bratislava, Slovakia Sue Mecham Polymer Solutions Incorporated, 2903C Commerce Street, Blacksburg, Virginia 24060, USA Robert J. Meier DSM Research, P.O. Box 18, 6160 MD Geleen, The Netherlands; Institut fu¨r Agrosphere, ICG-4, Forschungszentrum Ju¨lich GmbH, D-52425 Ju¨lich, Germany Christian Pellerin De´partement de chimie, Universite´ de Montre´al, Montre´al, QC, H3C 3J7, Canada Michel Pe´zolet De´partement de chimie, Pavillon Alexandre-Vachon, local 1084D, Univeriste´ Laval, Que´bec, G1V 0A6, Canada James D. Rancourt Polymer Solutions Incorporated, 2903C Commerce Street, Blacksburg, Virginia 24060, USA Duncan F. Robertson Intertek-MSG, D131, Wilton Centre, Wilton, Redcar, Cleveland, TS10 4RF, UK Jozef Rychly´ Polymer Institute, Slovak Academy of Sciences, Du´bravska´ cesta 9, 842 36 Bratislava, Slovakia. Shulamith Schlick Department of Chemistry and Biochemistry, University of Detroit Mercy, 4001 West McNichols Road, Detroit, Michigan 48221-3038, USA Alan Sentman Polymer Solutions Incorporated, 2903C Commerce Street, Blacksburg, Virginia 24060, USA John Sidwell Smithers Rapra Technology Ltd., Shawbury, Shrewsbury, Shropshire, SY4 4NR, UK Brian Starr Polymer Solutions Incorporated, 2903C Commerce Street, Blacksburg, Virginia 24060, USA Jason Todd Polymer Solutions Incorporated, 2903C Commerce Street, Blacksburg, Virginia 24060, USA Simone Wiegand Forschungszentrum Ju¨lich, IFF – Weiche Materie, Postfach 1913, 52425 Ju¨lich, Germany Peter Wilhelm Research Institute for Electron Microscopy, Graz University of Technology, Steyrergasse 17, A-8010 Graz, Austria
VOLUMES IN THE SERIES
Vol. 1A
Vol. 1B Vol. 1C Vol. 2A
Vol. 2B
Vol. 2C
Vol. 2D Vol. 3
Vol. 4
Vol. 5
Vol. 6 Vol. 7 Vol. 8
Vol. 9
Analytical Processes Gas Analysis Inorganic Qualitative Analysis Organic Qualitative Analysis Inorganic Gravimetric Analysis Inorganic Titrimetric Analysis Organic Quantitative Analysis Analytical Chemistry of the Elements Electrochemical Analysis Electrodeposition Potentiometric Titrations Conductometric Titrations High-Frequency Titrations Liquid Chromatography in Columns Gas Chromatography Ion Exchangers Distillation Paper and Thin Layer Chromatography Radiochemical Methods Nuclear Magnetic Resonance and Electron Spin Resonance Methods X-ray Spectrometry Coulometric Analysis Elemental Analysis with Minute Sample Standards and Standardization Separation by Liquid Amalgams Vacuum Fusion Analysis of Gases in Metals Electroanalysis in Molten Salts Instrumentation for Spectroscopy Atomic Absorption and Fluorescence Spectroscopy Diffuse Reflectance Spectroscopy Emission Spectroscopy Analytical Microwave Spectroscopy Analytical Applications of Electron Microscopy Analytical Infrared Spectroscopy Thermal Methods in Analytical Chemistry Substoichiometric Analytical Methods Enzyme Electrodes in Analytical Chemistry Molecular Fluorescence Spectroscopy Photometric Titrations Analytical Applications of Interferometry Ultraviolet Photoelectron and Photoion Spectroscopy Auger Electron Spectroscopy Plasma Excitation in Spectrochemical Analysis
xv
xvi
Volumes in the Series
Vol. 10 Vol. 11 Vol. 12
Vol. 13
Vol. 14 Vol. 15 Vol. 16 Vol. 17 Vol. 18 Vol. Vol. Vol. Vol. Vol.
19 20 21 22 23
Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol.
24 25 26 27 28 29 30 31 32 33 34
Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol. Vol.
35 36 37 38 39 40 41 42 43
Vol. 44 Vol. 45 Vol. 46
Organic Spot Tests Analysis The History of Analytical Chemistry The Application of Mathematical Statistics in Analytical Chemistry Mass Spectrometry Ion Selective Electrodes Thermal Analysis Part A. Simultaneous Thermoanalytical Examination by Means of the Derivatograph Part B. Biochemical and Clinical Application of Thermometric and Thermal Analysis Part C. Emanation Thermal Analysis and other Radiometric Emanation Methods Part D. Thermophysical Properties of Solids Part E. Pulse Method of Measuring Thermophysical Parameters Analysis of Complex Hydrocarbons Part A. Separation Methods Part B. Group Analysis and Detailed Analysis Ion-Exchangers in Analytical Chemistry Methods of Organic Analysis Chemical Microscopy Thermomicroscopy of Organic Compounds Gas and Liquid Analysers Kinetic Methods in Chemical Analysis Application of Computers in Analytical Chemistry Analytical Visible and Ultra-violet Spectrometry Photometric Methods in Inorganic Trace Analysis New Developments in Conductometric and Oscillometric Analysis Titrimetric Analysis in Organic Solvents Analytical and Biomedical Applications of Ion-Selective Field-Effect Transistors Energy Dispersive X-ray Fluorescence Analysis Preconcentration of Trace Elements Radionuclide X-ray Fluorecence Analysis Voltammetry Analysis of Substances in the Gaseous Phase Chemiluminescence Immunoassay Spectrochemical Trace Analysis for Metals and Metalloids Surfactants in Analytical Chemistry Environmental Analytical Chemistry Elemental Speciation – New Approaches for Trace Element Analysis Discrete Sample Introduction Techniques for Inductively Coupled Plasma Mass Spectrometry Modern Fourier Transform Infrared Spectroscopy Chemical Test Methods of Analysis Sampling and Sample Preparation for Field and Laboratory Countercurrent Chromatography: The Support-Free Liquid Stationary Phase Integrated Analytical Systems Analysis and Fate of Surfactants in the Aquatic Environment Sample Preparation for Trace Element Analysis Non-destructive Microanalysis of Cultural Heritage Materials Chromatographic-Mass Spectrometric Food Analysis for Trace Determination of Pesticide Residues Biosensors and Modern Biospecific Analytical Techniques Analysis and Detection by Capillary Electrophoresis Proteomics and Peptidomics: New Technology Platforms Elucidating Biology
Volumes in the Series
Vol. Vol. Vol. Vol. Vol. Vol.
47 48 49 50 51 52
Modern Instrumental Analysis Passive Sampling Techniques in Environmental Monitoring Electrochemical (Bio) Sensor Analysis Analysis, Fate and Removal of Pharmaceuticals in the Water Cycle Food Contaminants and Residue Analysis Protein Mass Spectrometry
xvii
This page intentionally left blank
PREFACE
When, over three years ago, we were asked to commission a book on polymer analysis, our initial reaction was to decline, since we both believed that there was enough excellent books already published that dealt with the subject matter. However, we then contemplated that most existing books cover the subject from a technique point of view, that is, they tend to have a format in which individual chapters focus specifically on a single technique, such as mass spectrometry, nuclear magnetic resonance, vibrational spectroscopy, thermal analysis methods, chromatographic methods, etc. Occasionally, the scope is wider, if we can put it that way, but in these cases the focus is on a particular segment of the world of polymers. It was during our discussions on this viewpoint when our industrial experience kicked in, for which we recognised that the paramount desire of the ‘‘customer for polymer molecular characterization and analysis’’ is that of problem solving, not of championing a single or set of particular techniques. What these customers ideally require is a solution or information that enables them to solve or overcome a problem on a timescale that is relevant to the customers’ business needs, whether they be research-related, production-related, property-related, service-related, marketing-related, competitive product deformulation,y It was with this mindset that we agreed to try to commission a book, the result of which you have in front of you, in which each chapter addresses a particular problem or property, for example, chain structure or chain end characterization, polymer degradation, molecular orientation, product failure,y, and in which the techniques were secondary, that is ‘‘a means to an end’’ rather than ‘‘how can I solve this problem/measure this property by the technique for which I am a recognised specialist?’’ The task we set for many of our authors was therefore often a very difficult one: that of providing as balanced a viewpoint as possible of the various techniques and methods that may be used to tackle a particular problem or property characterization, and how they may optimally complement each other, and their comparative limitations and strengths. This was our ultimate aim; that is, a text from which the essential information to tackle a problem, for which polymer analysis is required, could be readily distilled from its pages, and from which the supportive, confirmatory and complementary positions of the various measurement techniques could be readily grasped.
xix
xx
Preface
Our industrial experience should have forewarned us: while it is relatively easy to find well-recognised technique specialists, it did turn out, however, to be not trivial to find authors fully comfortable with covering the issues and all techniques from a problem-solving/property-related point of view. Some chapters might, therefore, from some specialist readers and reviewers perceptions, still have some missing issues albeit relevant. In other cases, for example, polymer degradation, optimum coverage has been achieved by including multiple chapters. Nevertheless, considering all the possible topics to be covered and the complexity of the issues involved, we believe most topics are well covered by the contributing authors, and, notwithstanding, we believe the coverage is comprehensive, and provides a unique text on the molecular characterization and analysis of polymers, and approaches our ideal closely. As intimated above, reaching this point, that is publication of this book, has not been a straightforward task; the road has been sometimes rocky, with various professional and personal problems causing both the need to refine our original outline and the need along the way to commission late in the project new authors. To all our chapter authors, we are therefore truly indebted. For those whose chapters we have ‘‘sat on’’ for nearly two years, we especially thank you for your understanding and patience! For those who ‘‘stepped into the breach’’ near the end, we especially thank you for coming to our aid! We are also very thankful to the publishers, Elsevier Science B.V., for their patience too! This book is divided up into sections. The first three chapters provide a background; sections that follow contain chapters dealing with polymer chain analysis, polymer morphology and structure, polymer degradation, polymer product analysis and support techniques. These are listed in more detail in Chapter 1, which also expands more fully on our industrial perception of the requirements for competence and appreciation in all techniques and methods for polymer molecular characterization and analysis. We hope you find this book of value and its approach both unique and technically informative and useful. John Chalmers Robert J. Meier November 2008
S ER I E S E D I TOR ’ S P R E F A CE
This volume on ‘‘Molecular Characterization and Analysis of Polymers’’ has been edited by John M. Chalmers and Robert J. Meier, both of whom have considerable experience in the industrial sector. They have compiled a broad compilation of chapters on the various aspects of polymer analysis and placed a clear and useful emphasis on problem solving, rather than on the techniques used. The first three chapters layout the background; the following chapters deal with polymer chemistry and microstructure and polymeric materials, polymer chain analysis, polymer morphology and structure, polymer degradation, polymer product analysis, and polymer product development support techniques. The book contains a considerable amount of information on the techniques and methods used for polymer molecular characterization and analysis. Various techniques covered include analytical options for polymer product analysis, like size exclusion chromatography, thermal methods, nuclear magnetic resonance spectroscopy, electron spin resonance spectroscopy, mass spectrometry, infrared spectroscopy, gas chromatography-mass spectrometry and liquid chromatography-mass spectrometry. The book is a useful addition to the Comprehensive Analytical Chemistry series and it is the first on the topic of polymer analysis in the series. A tremendous effort was made by the editors to achieve this compilation and as they say in their Preface ‘‘the road has been sometimes rocky’’. Thanks to the editors and all contributing authors for their time and efforts in preparing this comprehensive compilation of research papers that will make this book on molecular characterization and analysis of polymers a unique reference in this field. D. Barcelo´ Barcelona, April 14, 2008
xxi
This page intentionally left blank
SECTION I: Introduction
This page intentionally left blank
CHAPT ER
1 Introduction John M. Chalmers and Robert J. Meier
Contents
1. The Analytical Competence 2. Contents and Structure 3. Practical Considerations in the Multi-Technique Approach References
3 6 11 12
1. THE ANALYTICAL COMPETENCE Polymers are around us everywhere, and their industrial production is a major activity of the chemical industry throughout the world. As a consequence, there is a significant support related R&D (research and development) activity within both academia and industry. This applies to the search for new catalysts, synthesis of new polymers, as well as attempts to produce new polymer chain architectures, formulations, and finally the processing and shaping of polymers. Few polymers are used in their pure form: additives and fillers, including fibres, are commonly added to arrive at a material with the desired lifetime use properties. Polymers can be functionalised to improve certain properties such as adhesion or to make them suitable for use in a particular application, such as an electronic component or aerospace application. To verify that the polymer chain synthesized is what was expected, or in order to relate polymer properties to the structure of the material, one needs polymer analysis and characterisation tools. Analysis can be thought of as the breaking up of anything complex; it is the contrary of synthesis, and can sometimes be referred to as such as ‘reverse engineering’. Characterisation is the determination of properties, such as form, chemical structure, colour, etc. Morphology is the science of form. The build-up of a polymeric sample in terms of amorphous and crystalline domains, threedimensional networks, spherulites or other structural units, or the presence and distribution of glass-fibres or other filler material, constitutes the morphology of the sample. Morphological characterisation thus is a key means to establish structure–property relations. Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00401-7
r 2008 Elsevier B.V. All rights reserved.
3
4
John M. Chalmers and Robert J. Meier
Traditionally, analysis and, to a lesser extent, characterisation, have been viewed from the viewpoint of expertise in an individual technique, e.g., spectroscopy of polymers (infrared (IR) and Raman spectroscopies, mass spectrometry (MS) and nuclear magnetic resonance (NMR) spectroscopy), thermal properties of polymers (differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA)), surface characterisation (e.g., secondary ion mass spectrometry (SIMS) and atomic force microscopy (AFM)), etc. However, particularly in an industrial context, problem solving is primarily what product group customers of analytical groups are interested in and the technique expertises should be considered as supporting activities. Moreover, in academic groups those that synthesize polymers based on newly developed catalysts often want to undertake their own analyses. Such groups are essentially interested in appropriate answers from polymer analysis and characterisation, not in building up expertise in individual analytical techniques. What is needed primarily for problem solving and general analytical support is an analytical/characterisation science competence. The competence in polymer analysis is the capability to analyse polymers for constituents and properties, each in relation to the questions or interests from the customer. Whereas in academic synthetic groups the customer and the analyst may be one and the same person, in industry the customer is usually a different person, often with conflicting priorities of timescale. Defined as a competence, the traditional individual expertises, e.g., microscopy, spectroscopy, thermal analysis, etc., are considered as supporting the competence. Foremost is the capability to investigate, analyse and characterise, the polymer, both effectively and efficiently. ‘‘What do we want to know about the polymer?’’ is the question that comes first, whereas the technique and therewith the required expertise comes second. This, obviously, is not meant to suggest that an expertise in a specific technique is not important; in many cases the involvement of a technique expert is vital. However, in both the industrial environment as well as in academic synthetic and materials research groups, the problem solving capability is the key issue. With which technique the problem is going to be solved is less relevant. In most real cases all that matters is whether a problem is addressed appropriately, both in terms of the solution information and its derived timescale; this might, for example, in a failure analysis, simply be identifying cause and not a detailed reason. Important components of the solution may be any one or a combination of accuracy or precision really required, overall time to obtain the results, price per analysis, etc. Accuracy is mentioned at this point because the traditional expert has the tendency to strive for results that are scientifically the best. This, however, is often not required. This requires experts who are well trained in analytical competence thinking. Precision is sometimes much more important than accuracy in a quality assurance measurement. The key appreciation here is the difference between technique expertise and analytical competence. While retaining the necessary expertise on individual techniques, understanding of the customer questions and aims (the problem setting) is paramount. Understanding of the strengths, weaknesses and
Introduction
5
limitations of different techniques is an integral part of optimal performance in a competence. The level of technique expertise required will likely vary from one situation to the other. The requirement on technique expertise does not imply that in each laboratory where an analytical competence is required, a high-level analytical expertise level is required. What is required is the set of skills to provide analyses up to the level required and appropriate to the problem, and perhaps its value of solution. Whether equipment is in-house or elsewhere does not have to matter, as long as it is available when required for problem solving. Having said this, it was felt therefore that there is a need for a book addressing analysis and characterisation of polymers from the point of view of what we wish to call the primary analytical question. Many excellent textbooks and reference works exist which address one or more individual analytical techniques, see, for example, references [1–10]. These books form the basis of the knowledge of the technique expert. They also contain many excellent and varied examples on successful applications of analytical techniques to polymer analysis and characterisation. There are also books which address the multitude of analytical techniques applied in polymer analysis, see, for example, references [11–24]. However, a synthetic chemist may wish to know the constitution of his/her polymer chain, a material scientist may want to find out the reasons why a fabricated sample had failed. What technique is best or optimal to study chain constitution will depend on the situation. Polymer failure may result from morphological features, which needs to be avoided, a contaminant, a surface property degradation, etc. When a sample has been processed, e.g., a film blown, molecular orientation may be the key parameter to be studied. A formulation scientist may wish to know why an additive from a different supplier performs differently. It is from such points of view that polymer analysis and characterisation is addressed in this book. The aim of this book is therefore to present and discuss modern approaches and strategies to polymer characterisation and analysis. As appropriate, however, space will be given to theory, practice and instrumentation. While state-of-the-art characterisation methods will feature highly, conventional use of analytical techniques will also be well covered. The emphasis however, whenever possible, will be pragmatic and problem solving and property determination led, illustrated by ‘real-world’ application examples. As suggested above, the real accuracy or precision required, the time allowed to arrive at a satisfactory result, and the monetary/manpower budget available to obtain meaningful results are all integral elements when the intention is to run an analytical competence in optima forma. Therefore, the emphasis must be on the synergistic, complementary, effective and efficient usage of characterisation techniques and tools and analytical methodology, expertise and skill; it cannot be technique led. Foremost must be the property characterisation, the problem solution and effective polymer analysis; techniques provide the means, and per se should not be the driver! The materials covered in this book will be organic polymers; biopolymer and inorganic polymer characterisations are not considered. The characterisations will focus on polymer and polymer product microstructure and
6
John M. Chalmers and Robert J. Meier
composition; the discussions will not feature bulk property measurements, e.g., mechanical, electrical. The emphasis is on commercial materials and formulations. The reason is that commercial materials are rarely pure materials. A pure homopolymer is a rare species in the ‘real-world’ materials. To arrive at the desired material’s properties, either a copolymer is used, sometimes a blend or a dispersion, or additives or filler materials including rubber particles, carbon black or fibres of various type and make may be added, and are thus commonplace in commercial products. This implies a more complex constitution and morphology than expected for pure polymers. However, obviously, the methods described herein can be applied to pure, unmodified, polymers as well.
2. CONTENTS AND STRUCTURE In contrast to a book describing contributions of individual techniques, there is undoubtedly not a single way to structure the approach to be dealt with in this book. The approach taken is as follows. A polymer material consists of individual polymer chains, and all together these make the material and its morphology, which in turn relate to the material’s properties. A cluster of chapters addressing the individual chain characteristics was therefore thought appropriate, followed by another cluster on morphology. As mentioned before, as most polymeric materials for practical use are not pure polymers, a third cluster was formed dealing with analysis of the product, which includes issues such as additives and surface characteristics. Consequently, this book comprises six sections. The first section serves as an Introduction, it includes this chapter and the next two chapters, which deal with the basics of polymer chemistry and microstructure (Chapter 2) and polymeric materials and their composition, uses and application (Chapter 3). The next section (Polymer Chain Analysis: Chapters 4–6) relates to polymer chain analysis (chain structure characterisation, chain end characterisation and molecular weight and distribution). The third section (Polymer Morphology and Structure) that deals with polymer morphology and structure is subdivided into phase structure and morphology (Chapter 7), molecular orientation (Chapter 8) and polymer networks (Chapter 9). Chapters 10–12, the fourth section (Polymer Degradation), cover approaches to study and investigate polymer degradation. The next section, Polymer Product Analysis, covers spatial imaging and heterogeneity (Chapter 13), analysis of additives (Chapter 14), failure, defect and contaminant analysis (Chapter 15) and concludes with a short chapter on surface analysis (Chapter 16). The final section, which we have called Polymer and Polymer Product Development: Support Techniques, considers the role of computational chemistry and molecular modelling in supporting polymer analysis (Chapter 17), and high-throughput analysis (Chapter 18). The polymer characteristics addressed within these clusters are presented below in Table 1. Table 1 presents an overview of the many analytical/ characterisation techniques and methods used for the molecular characterisation
Introduction
7
Table 1 (a) Summary of the techniques used for molecular analysis and characterisation of polymers. The techniques and methods listed have been mostly picked from those mentioned in the chapters within this book; the order in which they appear is random, and does not reflect their relative importance or their order of most common use, particularly since they are most frequently used in synergistic, confirmatory and/or complementary combinations. (b) Abbreviation and acronym definitions for techniques cited in Table 1(a). (a): Polymer
Property to be analysed/ characterised
Suitable/primary techniques/methods
monomer, comonomer type and composition degree of polymerisation (dp) conformation (e.g., transgauche), isomerism (e.g., cis-trans) tacticity, stereoregularity chain lengths (persistence, Kuhn unit) branching (e.g., shortchain, long-chain, hyper-, star, ladder, brushes) unsaturation copolymer sequencing end-group analysis
NMR, IR, Raman
Polymer chain structure:
cross-linking
molecular weight, molecular weight distribution
NMR NMR, IR, Raman
NMR, IR SANS SEC, GPC, NMR, rheology, SANS, SAXS NMR, Raman, IR NMR, IR NMR, MS, MALDI-MS, IR, Raman, chemical titration indirect techniques, including s-NMR, gelpoint determination, rheology, LC-MS techniques can in part be applied GPC/SEC, MALDI-MS, membrane osmometry, vapour pressure osmometry, viscometry, light scattering, TDFRS, SAXS, SANS, SECHPLC, SEC-MS, SEC-IR, FFF, ultracentrifugation, MALDI-TOF-MS, NMR, capillary electrophoresis
8
John M. Chalmers and Robert J. Meier
Table 1 (Continued ) (a): Polymer
Property to be analysed/ characterised
Suitable/primary techniques/methods
crystallinity, amorphous content, phase analysis
WAXS, WAXD, SAXS, SALLS, density, DSC, IR, Raman, s-NMR, AFM, optical microscopy, SEM, TEM WAXD, s-NMR, IR, Raman, fluorescence spectroscopy, birefringence CL, ESR, ESRI, IR/IR microscopy, Raman/ Raman-microscopy, GC-IR, EGA-IR, Py-IR, Py-GC-IR, UV, visible spectroscopy, fluorescence/ phosphorescence, MS, MALDI-TOF-MS, GC-MS, Py-MS, Py-GCMS, GPC, SEC, GPC-MS, GPC-IR, s-NMR, NMR, TA, DSC, TGA, oxidative-induction time (DSC), DPC, TGA-IR, TGA-MS, GC, IGC, LC, LC-CC, HPLC, LC-IR, LC-MS, XPS, SIMS, optical microscopy, oxygen uptake, carbonyl index (IR), iodometric test, titration, staining, MFI
Polymer material/product characterisation:
molecular orientation
degradation, oxidation
Product analysis: polymer network
s-NMR, gelation, swelling, birefringence, IR, NMR, STM, SANS, Brillouin scattering, pulsepropagation
Introduction
Table 1 (Continued ) (a): Polymer
Property to be analysed/ characterised
Suitable/primary techniques/methods
surface analysis
optical microscopy, XPS (ESCA), IR-ATR, Raman, AFM, SIMS, LEIS, IR optical microscopy, IR-microscopy, Ramanmicroscopy, TOF-SIMS, NIR-imaging, SNOM, MRI, ESRI, mXRF, PES, LEIS, RIS AAS, GC, GC-MS, IR, HPLC, LC-MS, ICP-AES, SEM, TGA, XRF, NMR optical microscopy, IR, Raman, XRF, DSC, TGA, NMR, SEM, SEM-EDS, XPS, SIMS, GPC/SEC, ICP-MS, GC-MS, LC-MS, AFM
spatial heterogeneity
additive analysis
failure, defect, contaminant analysis
(b)
AAS AFM ATR CL DPC DSC EDS EGA ESCA ESR ESRI FFF GC GPC HPLC IGC ICP-AES ICP-MS IR LC LC-CC
Atomic absorption spectrometry Atomic force microscopy Attenuated total reflection Chemiluminescence Differential photocalorimetry Differential scanning calorimetry Energy dispersive spectroscopy Evolved gas analysis Electron spectroscopy for chemical analysis Electron spin resonance spectroscopy Electron spin resonance imaging Field-flow fractionation Gas chromatography Gel permeation chromatography High-performance liquid chromtography Inverse gas chromatography Inductively coupled plasma atomic emission spectroscopy Inductively coupled plasma mass spectrometry Infrared Liquid chromatography Liquid chromatography under critical conditions
9
10
John M. Chalmers and Robert J. Meier
Table 1 (Continued ) (b)
LEIS MALDI-TOF-MS MFI MRI MS NIR NMR PES Py RIS SALLS SANS SAXS SEC SEM SIMS s-NMR SNOM STM TA TDFRS TEM TGA ToF WAXD WAXS XPS XRF mXRF
Laser enhanced ionisation spectroscopy Matrix-assisted laser desorption time-of-flight mass spectrometry Melt flow index (Nuclear) magnetic resonance imaging Mass spectrometry Near-infrared spectroscopy Nuclear magnetic resonance spectroscopy Photoelectron spectroscopy Pyrolysis Resonance ionisation spectroscopy Small-angle laser light scattering Small-angle neutron scattering Small-angle X-ray scattering Size exclusion chromatography Scanning electron microscopy Secondary ion mass spectroscopy Solid state nuclear magnetic resonance spectroscopy Scanning near-field optical microscopy Scanning tunnelling microscopy Thermal analysis Thermal diffusion forced Rayleigh scattering Transmission electron microscopy Thermogravimetric analysis Time-of-flight Wide-angle X-ray diffraction Wide-angle X-ray scattering X-ray photoelectron spectroscopy X-ray fluorescence spectroscopy micro-X-ray fluorescence spectroscopy
and analysis of polymers and polymer formulations and products. While one or two techniques/methods may be dominant in a particular area, it can be readily seen that several to many can be applied depending on the information required and the depth of problem solving and understanding that is needed, along with the suitable or most common analytical techniques. The requirement and need for a multi-technique attack on a problem or study is probably most exemplified in the chapter on polymer failure (Chapter 15) and polymer degradation (see Chapter 10); in the latter many of the references cited used five or more analytical/characterisation tools in the investigation. The need for a multitechnique approach is an even more prominent need in the study of polymer morphology, although perhaps less often practised in single studies. A key
Introduction
11
feature here obviously is the various length scales involved, from single chain conformation and configuration (as they co-determine the possibility of certain larger structures to be formed) to crystalline lamellae, shperulites, etc. Key issues when polymer chain analysis or polymeric materials characterisation is applied is the choice of property to analyse, and when selected, which is the most suitable technique given the question to be addressed and circumstances, e.g., business pressure (availability, price, accuracy, speed).
3. PRACTICAL CONSIDERATIONS IN THE MULTI-TECHNIQUE APPROACH Whereas several techniques may thus be used to study a certain characteristic of a polymer sample, for instance IR and Raman spectroscopy and X-ray diffraction as well as NMR may be used to determine or infer the crystallinity level of a sample, different techniques work differently and therefore usually do not measure the same. What this means is that crystallinity levels obtained from the same sample may differ when a different technique is applied, see, for example, ref. [23] and chapter 7 and references therein. However, these differences do not necessarily imply one technique being better than another. In fact these differences may contain useful information on the sample (see, for example, ref. [25]). This brings us to the point of considering the suitability of a technique with respect to a certain analysis, particularly from an industrialist’s or contract laboratory viewpoint. This is a very important consideration, as this is not a priori straightforward. There are a number of factors influencing the choice. We will mention just a few of these in arbitrary order: (i)
(ii) (iii) (iv) (v) (vi) (vii) (viii)
When, for whatever reason, one does not wish to be involved in further method development but just apply a technique, this means that the technique must have been applied to the problem of interest before, or it must be essentially a trivial translation from a previously demonstrated application. Example: IR spectrum of an unknown, NMR can do the job; X-ray crystallinity. Does the technique need to be applied on a lab-scale or in-process? Does the technique have to be applied off-, at-, in- or on-line? Is cost of analysis relevant? What is the accuracy/precision required? Is concentration/composition to be measured? Is speed important? Do you have the equipment available (in-house or otherwise readily available)? If such as a failure analysis, is it just satisfactory to identify the cause, or does reason matter too?
The chapters following in this book should, we hope, enable one to obtain an objective assessment and comparison of the most appropriate polymer molecular
12
John M. Chalmers and Robert J. Meier
characterisation or analysis tool according to the problem solving circumstances. The reader will be able to obtain experts’ overviews of the range of tools, and their strengths, convenience of use and limitations, necessary to characterise or analyse the molecular structure, composition and properties of polymers and their formulated products.
REFERENCES 1 I. Ando and T. Asakura, Solid State NMR of Polymers, Elsevier, Amsterdam, 1998. 2 F. Bovey and P. Mirau, NMR of Polymers, Elsevier, Amsterdam, 1996. 3 J.M. Chalmers and P.R. Griffiths (Eds.), Handbook of Vibrational Spectroscopy, Vol. 4, Wiley, Chichester, 2002. 4 N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007. 5 P. Worsfold, A. Townshend and C. Poole (Eds.), Encyclopedia of Analytical Science, 2nd ed., Academic Press, London, 2004. 6 D. Briggs, Surface Analysis of Polymers by XPS and Static SIMS, Cambridge University Press, Cambridge, 1998. 7 S. Schlick (Ed.), Advanced ESR Methods in Polymer Research, Wiley, Chichester, 2006. 8 W.M. Groenewoud (Ed.), Characterisation of Polymers by Thermal Analysis, Elsevier, Amsterdam, 2001. 9 I. Wilson, C. Poole and M. Cooke (Eds.), Encyclopedia of Separation Science, Academic Press, London, 2000. 10 G. Montaudo and R.P. Lattimer, Mass Spectrometry of Polymers, CRC Press, Boca Raton, 2001. 11 B.J. Hunt and M.I. James (Eds.), Polymer Characterisation, Blackie Academic & Professional, Glasgow, 1993. 12 J.L. Koenig, Spectroscopy of Polymers, 2nd ed., Elsevier Science, New York, 1999. 13 J.I. Kroschwitz (Ed.), Polymers: Polymer Characterization and Analysis, Wiley, New York, 1990. 14 J.I. Kroschwitz, Concise Encyclopedia of Polymer Science and Engineering, Wiley, New York, 1998. 15 Polymers and Rubbers. In: R.A. Meyers (Ed.), Encyclopedia of Analytical Chemistry, Wiley, Chichester, 2002. 16 H.F. Mark (Ed.), Encyclopedia of Polymer Science and Technology, 3rd ed., Wiley-VCH, Weinheim, 2004. 17 J.C.J. Bart, Additives in Polymers: Industrial Analysis and Applications, Wiley, Chichester, 2005. 18 J. Scheirs, Compositional and Failure Analysis of Polymers: A Practical Approach, Wiley, Chichester, 2000. 19 J. Haslam, H.A. Willis and D.C.M. Squirrell, Identification and Analysis of Plastics, 2nd ed., Buterworth, London, 1972. 20 J.I. Kroschwitz (Ed.), Concise Encyclopedia of Polymer Science and Engineering, Wiley, Chichester, 1998. 21 R.A. Pethrick and J.V. Dawkins (Eds.), Modern Techniques for Polymer Characterisation, Wiley, Chichester, 1999. 22 M. Bolgar, J. Hubbal, J. Groger and S. Meronek, Handbook for the Chemical Analysis of Plastic and Polymer Additives, CRC Press, Boca Raton, 2007. 23 D. Campbell, R.A. Pethrick and J.R. White, Polymer Characterization: Physical Techniques, 2nd ed., CRC Press, Boca Raton, 2000. 24 R.A. Prethrick, Polymer Structure Characterization from Nano to Macro Organization, RSC Publishing, Cambridge, 2007. 25 R.J. Lehnert, P.J. Hendra, N. Everall and N.J. Clayden, Comparative quantitative study on the crystallinity of poly(tetrafluoroethylene) including Raman, infra-red and F nuclear magnetic resonance spectroscopy, Polymer, 38(7) (1997) 1521–1535.
CHAPT ER
2 Polymer Chemistry and Microstructure Jacques Devaux and Sophie Demoustier-Champagne
Contents
1. Introduction 2. Polymer: Definitions 2.1 Monomers, chain length, length distribution 2.2 Thermoplastics and thermosets 2.3 Thermal transitions and properties 2.4 Microstructure 3. From Molecules to Macromolecules 3.1 Chain length and entanglements 3.2 End groups 3.3 Chain substituents 3.4 Spatial arrangements 4. Fundamentals of Polymer Chemistry 4.1 Chain polymerisation vs. step polymerisation 4.2 Types of chain polymerisations and polymers synthesized — keypoints of mechanisms, kinetics 4.3 Radical chain polymerisations 4.4 Ionic polymerisations — active species 4.5 Olefin polymerisation processes 4.6 Processes for polyolefin syntheses 4.7 Copolymers 4.8 Types of step polymerisations and polymers synthesized — keypoints of mechanisms, kinetics 5. Polymer Degradation 6. Summary References
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00402-9
14 15 15 17 17 21 25 27 27 28 28 34 34 35 35 42 45 48 50 53 58 62 62
r 2008 Elsevier B.V. All rights reserved.
13
14
Jacques Devaux and Sophie Demoustier-Champagne
1. INTRODUCTION ‘‘A material is a solid used by man to produce items that constitute the support for his living environment’’ [1]. Such a definition, although restrictive as it excludes liquids, is simple enough. It might imply however, on the one hand, that materials as such only existed from the beginning of mankind, moreover, on the other hand, that the usual three classes of ‘‘materials’’ — ceramics, metals and polymers — have always coexisted. Indeed, most of the earth’s terrestrial crust is made of minerals, the majority of which are considered to be ceramics, that is, ‘‘resulting from the combination of a limited number of metallic elements (Si, Ca, Mg, Al, Ti, etc.) with non-metallic elements, most commonly oxygen’’ [1]. Ceramic materials marked the so-called ‘‘Stone Ages’’, the earliest stages of civilisation. A few pure (native) metals have existed as materials from the first ages of mankind, namely those that have a high oxido-reduction potential, which protects against oxidation by atmospheric oxygen (e.g., gold, platinum, silver,y). Their bright colour and inalterability led humans to use them in jewellery. However, geological science tells us that huge amounts of natural metals exist in the earth’s nucleus (e.g., Si, Al, Fe, Ni, etc.), which constitute the main part of the earth’s mass. Being oxidised through reaction with oxygen, landmarks in civilisation’s progress (bronze age, iron age) are labelled by mankind’s mastering of more and more complex metal productions (reduction). Natural polymers are far more complex materials, being exclusively ‘‘organic’’, that is, products of life (cellulose, proteins, DNA,y). Nevertheless, as nature seems to have formed (size, weight, hardness, etc.) several natural polymers (wood, bones, ivory, etc.) in such a way as to be almost immediately usable by our ancestors, they were most probably the bases of the first human tools. The commonly widespread conception that polymers are the youngest ‘‘materials’’ in the historical world is not true, but, strictly speaking, only applies to synthetic polymers, which were discovered about 100 years ago, early in the XXth century. Polymers are undoubtedly ‘‘materials’’. Knowledge and understanding of their properties belongs to the so-called field of ‘‘Materials Science’’. Study and understanding of their formation, properties and performance characteristics involves chemistry, physico-chemistry and physics, the latter including mechanics, optics, electricity, etc. Material’s knowledge is not limited to the aforementioned fields of science, but includes also technological properties, which are most often used for their classification: strength, hardness, transparency, conductivity, etc. Materials science is thus built on complex interrelationships between such fields, see Figure 1. Few properties, if any, depend directly and only on the chemistry. Indeed, as shown in Figure 1, the ‘‘route’’ implies that it is chemistry that influences (micro-) structure, which, in turn, governs properties. Processing, which is not often classified as a ‘‘science’’ but as ‘‘engineering’’, has to find its place in the picture, since it is the normal way to go from a macromolecule to a product with the desired properties.
Polymer Chemistry and Microstructure
15
Processing Synthesis
Characterisation
Microstructure
Properties
Figure 1 Polymers in materials science: Interrelationships between synthesis, processing, microstructure, properties and characterisation.
Characterisation covers a wide field of science and technology and interacts from the synthesis stage through the analysis of structure to the determination of properties. Characterisation allows one to observe, control and model (including ‘‘closed-loop’’ backward interaction) all the complex interrelationships of materials science.
2. POLYMER: DEFINITIONS 2.1 Monomers, chain length, length distribution The word ‘‘polymer’’ (first proposed by Berzelius in 1833) is made of ‘‘poly’’ from the ancient Greek word ‘‘poluB’’ meaning ‘‘many’’ and ‘‘meroB’’ meaning ‘‘part’’. Polymers are molecules built up from numerous identical chemical ‘‘units’’ spatially repeated to form a chain. From the early times and still nowadays, a distinction is often made between ‘‘natural’’ and ‘‘synthetic’’ polymers, but it is somewhat artificial as natural polymers can now sometimes be synthesized (e.g., synthetic ‘‘natural rubber’’) and some synthetic polymers, which are never found in nature, can be synthesized by natural ways (enzymatic syntheses). Nevertheless, synthetic polymers are most often made from monomers (from ancient Greek ‘‘monoB’’ meaning single), which are precursor molecules of a polymer chain. When only a few monomers are joined to form a chain, they are called oligomers (from ‘‘oligoB’’ a few, in ancient Greek). Despite this distinction between oligomers and polymers is rather ill defined, one generally conceives that polymer chains exhibit high molecular masses ranging from 104 to about 107, the masses of oligomers being conventionally limited to below about 104. Polymer is also a word the use of which is restricted to chemical compounds based on covalent links, chemically stable at ambient conditions. Most often polymers are made from carbon and hydrogen or hydrocarbon derivatives (with oxygen, nitrogen, sulfur, halogens,y) (Table 1). But, they are sometimes based on inorganic backbone atoms (silicon, nitrogen and phosphorous,y). From the above considerations, it appears that chain length is a main characteristic of polymers. Natural macromolecules, particularly in living bodies, can exhibit exact lengths, thus exact molecular masses. For instance haemoglobin molecular mass is known to within one dalton. However, a synthetic polymer
16
Jacques Devaux and Sophie Demoustier-Champagne
Table 1
Examples of some ‘‘natural’’ and ‘‘synthetic’’ polymers
Name of polymer
Formula
Polyethylene
Approximate date of invention
1935
C C H2 H2 n
Polypropylene (isotactic)
1954
C CH H2 n CH3
Poly(methyl methacrylate) (PMMA)
O
C
O
1935
CH3
C C H2 n CH3
Poly(vinyl chloride) (PVC)
1872
C CH H2 n Cl
Polystyrene
1925 C CH H2 n
Poly(ethylene terephthalate) (PET)
Poly(hexamethylene adipamide) (Nylon 66)
1941 H
O
C C O H2 H2
C
C
O
O
H
N H
Cellulose
O
C N C H2 6 H
H2 C OH O H HO H H H
OH
1938
O
O
OH n
C OH C H2 4 n
H O
HO H
Natural polymer
OH H H
O C OH H2
n
Polymer Chemistry and Microstructure
17
sample contains chains having a wide distribution of chain length. The breadth of the molecular mass1 distribution depends on the synthesis process. Therefore, it is necessary to define average molecular masses to characterize a polymer sample. The simplest method — the number average molecular mass or Mn — is an arithmetic average based on the total mass of a sample divided by the total number of molecules in this sample. For correlation with most physical properties (mechanical strength, optical scattering), mass average molecular mass of a polymer ‘‘Mw ’’ appears more satisfactory. Higher-power averages like z-average molecular mass ‘‘Mz ’’ seem to better correlate with rheological properties. Expressions of Mn ; Mw and Mz are P P 2 P 3 ni mi
i Mn ¼ P n
i
ni mi
i Mw ¼ P nm
i
i
i
i
ni mi
i Mz ¼ P n m2 i
i
i
where ni and mi are the number and the molecular mass of molecules containing i units, respectively. A measure of the breadth of the molecular mass distribution is given by the ratios of molecular mass averages. The most commonly used ratio Mw =Mn ¼ H, is called the polydispersity index. Wiegand and Ko¨hler discuss the determination of molecular masses (weights) and their distributions in Chapter 6.
2.2 Thermoplastics and thermosets Thousands of polymers have been synthesized and more are likely to be produced in the future. Fortunately, all polymers can be divided into two major groups based on their thermal processing behaviour. Some polymers behave as (viscous) liquids upon heating and can be re-processed, almost indefinitely. These are classified as ‘‘thermoplastics’’ (from the ancient Greek prefix ‘‘yermo’’ for ‘‘heat’’). Some major commercial examples are polystyrene (PS), polyethylene, polypropylene and poly(vinyl chloride) (PVC). Other polymers keep their (definitive) shape after a first heating step during synthesis or subsequent treatment. These are called ‘‘thermosets’’. Once formed the crosslinked networks resist heat and solvent attack. Such properties make thermosets suitable materials for composites, coatings and many adhesive applications. Major examples of thermosets include epoxy resins, phenol-formaldehyde resins, urea/melamine formaldehyde resins and unsaturated polyesters.
2.3 Thermal transitions and properties 2.3.1 Glass transition Matter is made from atoms or molecules, for which the spatial arrangements depend on cohesion (energy from interaction forces) and thermal energy, which is proportional to temperature. Weak cohesion and/or high temperatures lead to 1
The notation M is used here for molecular masses, while X is used for chain lengths (or ‘‘degrees of polymerization’’). M ¼ XMO with MO, the molecular mass of one unit in the polymer chain.
18
Jacques Devaux and Sophie Demoustier-Champagne
gases, while, in contrast, high cohesion and/or low temperatures yields solids, with liquids as an intermediate state. There are rather limited differences between liquid and solid states as specific masses of solids are usually only about 15% higher than those of corresponding liquids. Inside liquids, due to the rather low level of empty volume (the so-called ‘‘free volume’’), molecules can move due to ‘‘concerted’’ movements of the neighbouring molecules. Upon cooling down a liquid, the ratio between the thermal and the cohesion energy decreases, molecules become closer to each other and the free volume decreases. Thermal energy, which leads to molecular mobility, becomes lower, and attraction and repulsion forces between molecules begin to play a more significant role. When these latter forces predominate over thermal energy, an equilibrium is usually reached between them leading to ordered (crystalline) structures. However, this is only the case when the time needed for molecular movement (the so-called ‘‘characteristic time’’) is lower than that of cooling. When no extended ordering can occur and/or if molecular movements are extremely slow (very big and/or branched molecules) and/or if the cooling is very fast, ordering remains limited to rather small ‘‘domains’’ of molecules. The solid is said to be ‘‘amorphous’’ and retains in the solid state, the rather disordered microstructure (including the free volume) of a liquid. Figure 2 shows how atomic organisation changes with temperature. The temperature at which a liquid (highly viscous, or even rubbery for very high molecular masses) becomes an amorphous solid (rigid, stiff, often brittle) on cooling (or vice versa an amorphous solid becomes liquid on heating) is called the glass transition and noted Tg (Figure 3). In the glassy state, thus below Tg, very few molecular movements (group rotations, vibrations) are allowed. Above Tg, large-scale motions involving the whole macromolecule (translations, repetations) become possible. It has to be noticed that no isothermal volume contraction on cooling or volume expansion on heating is associated with Tg, contrary to crystallisation or melting. The latter is a true first-order transition exhibiting a discontinuity in
Figure 2 Evolution of atomic organisation with increasing temperature. Reproduced from Mercier, Zambelli and Kurz [1], Elsevier (2002) with permission of Elsevier. Copyright Elsevier 2002.
Polymer Chemistry and Microstructure
19
Figure 3 Curves of specific volumes vs. temperature for poly(vinyl acetate) measured on cooling. Equilibrium values measured 0.02 h and 100 h after cooling, as indicated. Tgu and T g are glass transitions respectively at fast and slow cooling rate. Reproduced from Ref. [2] with permission of John Wiley & Sons, Inc.
thermodynamic variables. Despite the discontinuity occurring only in the first derivative of thermodynamic variables, Tg is not a true ‘‘second-order’’ transition as it also depends on kinetics. Figure 3 also shows how Tg moves with cooling rate for a sample of poly(vinyl acetate). Tg is said to be a ‘‘kinetic transition’’.
2.3.2 Crystallisation-melting temperature The commonest state of the solid matter is the crystal. A crystalline solid is made of a periodic arrangement of atoms (or small molecules) in the three dimensions of space. A (single) crystal is a very ordered state formed by the juxtaposition of numerous identical ‘‘unit cells’’ (parallelepipedic volume containing one atom or one small molecule). A crystal structure is characterised by its symmetry [1]. Due to the length of the macromolecules, the existence of single crystals of polymers has remained a controversy for a long time. Soon after World War II, microscopic polymer ‘‘single crystals’’ were obtained by very slow cooling from
20
Jacques Devaux and Sophie Demoustier-Champagne
Figure 4 Scheme of chain folding in polymer crystals.
dilute solutions. Upon cooling from the liquid state at a suitable rate, polymers whose chain segments (including a few repeat units) exhibit symmetry elements of high enough order, can thus crystallise. Such a crystallisation goes along with long-range ordering. The determination of the ‘‘unit cell’’ led to the conclusion that, within such a single crystal, one macromolecule encompasses many ‘‘unit cells’’, which, itself, includes only one or a few ‘‘repeat units’’. Moreover, upon examination by electron diffraction, it appeared also that in these ‘‘single crystals’’, the chain axis was perpendicular to the largest faces, thus, that the chains are oriented in the ‘‘thickness’’ direction. However, as such thicknesses are much smaller than extended-chain lengths, a model of ‘‘chain folding’’ was established for forming such polymer crystals (Figure 4). As a consequence of chain folding, besides the inclusion of chain ends, these ‘‘single crystals’’ exhibit at a minimum a certain amount of defects at their surface. This is a reason why polymers are never 100% crystalline. In polymers crystallised from the melt, lamellae were observed by electron microscopy, whose thickness are of the same order of magnitude as ‘‘single crystals’’ obtained from solution (Figure 5). Crystal ‘‘unit cells’’ within these lamellae are comparable to those of single crystals and the chains are also oriented in the thickness direction. Therefore, the same model of chain folding was applied to melt-crystallised polymers. However, lamellae are, by far, less perfect structures than ‘‘single crystals’’ and each individual polymer chain gives rise to only a limited number of ‘‘folds’’, its remaining part (the so-called ‘‘tie’’) protrudes from the lamella and remains in an amorphous phase. By this way, the crystallinity of melt-crystallised polymers lie within a range extending from 85% to 90% for very regular and flexible polyethylene chains down to about 30–40% maximum for most other crystallisable polymers. Polymers are often said to be ‘‘semi-crystalline’’, whereas ‘‘partly crystalline’’ should be more correct. By optical microscopy (OM), birefringent structures are observed in semicrystalline polymers, characterized by ‘‘Maltese-crosses’’ under crossed polars as seen in Figure 6. As these structures grow symmetrically in three dimensions
Polymer Chemistry and Microstructure
21
Figure 5 Electron micrograph of a portion of melt crystallised polyethylene spherulite by transmission electron microscopy (TEM) showing lamellae. Reproduced from Ref. [3] with permission of John Wiley & Sons, Inc.
from a nucleus, they are called ‘‘spherulites’’. Upon examination, they appear to be formed of ‘‘fibrils’’ growing from the nucleus. These fibrils include several lamellae most often linked by tie-molecules going from one lamella to its neighbour. In semi-crystalline polymers, ordered structures appear at different dimensional levels 1. 2. 3. 4.
the the the the
crystal cell lamella fibril spherulite.
Such a complex microstructure is illustrated in Figure 7.
2.4 Microstructure 2.4.1 Linear and branched homopolymers Polymers that are built from the repetition of identical ‘‘repeat units’’ are called ‘‘homopolymers’’ (from ancient Greek ‘‘o`moB’’ ¼ same).2 Linear homopolymer chains are obtained upon linking chemically identical units exclusively at both ends. However, repeat units are not always symmetrical in the chain direction. Depending on the orientation of the repeat unit, different microstructural 2
Copolymers that are made from the repetition of two (or a very few) different units will be the subject of a later paragraph.
22
Jacques Devaux and Sophie Demoustier-Champagne
Figure 6 Spherulites of isotactic poly-1-butene (a, during growth) and of polyethylene (b, after completion) by optical microscopy (OM) under crossed polars. Reproduced from Ref. [3] with permission of John Wiley & Sons, Inc.
Growth
Intercrystalline tie chain (amorphous)
Crystalline lamellae
Amorphous phase
Nucleating seed
Figure 7 Scheme of the internal structure of a spherulite. Reproduced from Mercier, Zambelli and Kurz [1], Elsevier (2002) with permission of Elsevier. Copyright Elsevier 2002.
Polymer Chemistry and Microstructure
CH3 CH3
CH3 C H2
C H
C H2
C H
A
C H B
CH3 C H2
C H2 C
C H
23
CH3 C H2
C H
A
Figure 8 Schemes of (A) ‘‘head–tail’’, (B) ‘‘head–head’’ and (C) ‘‘tail–tail’’ microstructural arrangements in polypropylene.
SCB
LCB
Dendrimer
Hyperbranched
Figure 9 Examples of branching in polymers LCB (long-chain branched, e.g., LDPE) and SCB (short-chain branched, e.g., LLDPE), dendrimer and hyperbranched.
arrangements — ‘‘head–head’’, ‘‘head–tail’’ or ‘‘tail–tail’’ — can occur (1D microstructure); these are called positional isomers (Figure 8). Due to either accidental or intentional events during the synthesis, branching points can occur along the chain (2D microstructure). Although this needs the presence at the branching point of, stricto sensu, a ‘‘non-identical’’ unit, these macromolecules remain classified as homopolymers. Branching can also give rise to either the so-called ‘‘long-chain branching’’ (LCB) or ‘‘short-chain branching’’ (SCB), see Figure 9. Such terms are of importance particularly for polyethylene as they describe the only3 small ‘‘chemical’’ difference between technologically highly different low-density (LDPE) and linear lowdensity (LLDPE) polyethylenes. Except for polyethylene, the distinction between LCB and SCB is somewhat controversial as it can depend on several characteristics or even on the capacity of the characterisation method itself. From the branching point three or more chains can arise. This depends on the so-called ‘‘functionality’’ of the ‘‘monomer’’ at the branching point (the ‘‘branching unit’’). This functionality can be defined as the number of molecules (monomers, branches) actually linked to one branching unit. This definition can be extended to monomers purposely inserted into a chain to create branching. In this case the definition of functionality is generalized to the number of monomers that can link to the considered unit. ‘‘Normal’’ monomers have thus a functionality of 2. Branching units can exhibit functionalities of 3, 4 or more.
3
End groups are not taken into account here.
24
Jacques Devaux and Sophie Demoustier-Champagne
2.4.2 Dendrimers and hyperbranched polymers Highly non-linear homopolymers can even be synthesized exclusively from monomers of functionality higher than 2. Dendrimers (from ancient Greek ‘‘dendron’’ ¼ tree) are obtained when all the reaction sites of each branch links to another one and when all branches exhibit the same length. Whereas, hyperbranched (HB) polymers result from incomplete reaction of each multifunctional monomer, see Figure 9.
2.4.3 Crosslinked homopolymers As the number of branching points per chain increases, (when it becomes W2) an almost infinite network of covalent bonds can be created. Strictly all the system belongs to only one giant macromolecule. The polymer becomes insoluble and infusible; it is said to be ‘‘crosslinked’’. Even if, formally, an infinite network of covalent bonds can give rise to a 2D infinite structure (when grown onto a surface, for instance), crosslinked polymers are generally considered as 3D structures. Such crosslinked structures can be made either by using monomers exhibiting functionalities higher than 2 (thermosets like polyepoxides, phenolics), or by inducing a reaction of preformed linear chains with ‘‘bridging’’ molecules (e.g., vulcanisation of natural rubber) (Figure 10). Crosslinked 3D networks are normally amorphous,4 infusible and insoluble. Solvents can only swell networks. However, polymers resulting from polymerisation of molecules of functionality higher than 2 can remain soluble during the course of synthesis, below a certain ‘‘critical conversion value’’. Above this state, ‘‘gelation’’ occurs. Even in this state, the system remains partially soluble. It can be separated by solvent extraction into two phases: the soluble phase is called the ‘‘sol’’ and the insoluble phase the ‘‘gel’’. As the monomer conversion proceeds, the amount of ‘‘sol’’ decreases, while the amount of ‘‘gel’’ increases. The behaviour of crosslinkable amorphous systems during their synthesis can be described in the so-called time–temperature transformation or ‘‘TTT diagram’’ (Figure 11). It has to be noticed that such a TTT diagram can only be used in the direction of increasing time (transformation). A particular characterisation of a crosslinked system is the determination of the crosslink density. Access to the measurement of such crosslink densities is possible through models requiring determining the swelling of these systems.
2.4.4 Linear and branched copolymers Copolymers are built from the repetition of two (or more) ‘‘repeat units’’. Depending on the spatial arrangement of those units (e.g., A and B) along the chain (sequencing), various types of copolymers can be made: alternating, block, random (or statistical), branched, crosslinked (see Figure 12). More sophisticated microstructures are sometimes synthesized, but the highly complex chain sequencing encountered in natural copolymers, like proteins or 4
Depending on the mobility of chain segments, some crystallisation can occur in crosslinked systems.
25
Polymer Chemistry and Microstructure
C CH C C H2 H2 H
C CH H2
Cross-link C C H2 H
A
C CH H2
CH C H2
C CH C C H2 H2 H
C H2
CH3 CH
C
C H
C H2
S
B
S C C H2 H
C
C H
CH3
Figure 10 Examples of crosslinked polymers (A, polyfunctional; B, vulcanised).
enzymes, are still not accessible to chemical synthesis at the beginning of the third millennium. Several physical properties of copolymers are directly or indirectly dependent upon the distribution of sequences. The phase behaviour (microphase separation) in block copolymers is linked to the mutual insolubility/ solubility of the sequences. This will be discussed further.
3. FROM MOLECULES TO MACROMOLECULES As mentioned previously, chemistry and physico-chemistry play major roles in polymer microstructure, and, as a consequence, on polymer properties. The characterisation of several chemical parameters of polymer chains is thus of paramount importance for controlling the final properties of polymer materials Chain length or molecular masses J Entanglement J Concentration and type of end groups Nature of chain substituents
26
Jacques Devaux and Sophie Demoustier-Champagne
UNGELLED GLASS GELLED GLASS GELATION
TIME TO GELATION AND VITRIFICATION
GLASS
VITRIFICATION
RUBBER LIQUID
GELATION
Tgg
Tg∞
CURE TEMPERATURE, TCURE
Figure 11 Example of time–temperature transformation (TTT) diagram. (Increasing time in vertical direction). Reprinted from Roller and Gillham [4], published by the Federation of Societies for Coatings Technology, with permission of publisher.
A A B A A B B B A B B A
Random
B
A B
A B
A B
A A A A A B
B
A B
A B
A
Alternate
B
B
B
Block or sequenced
B
B
A A A A A A A A A A A A B
B
B
B
B
Figure 12 Examples of microstructures of copolymers.
Branched
Polymer Chemistry and Microstructure
27
Spatial arrangement J Cis–trans isomerism J Chain configuration J Chain conformation The chain structure (length, entanglement, branching, tacticity,y) of polymers is discussed further in the next chapter (Chapter 4) by Beaucage and Kulkarni.
3.1 Chain length and entanglements An important chemical characteristic of a polymer is the chain length. Chain length strongly influences the thermal properties as illustrated in Table 2 for several aliphatic compounds of different lengths. Detailed studies have been published on the influence of chain length on melting temperatures of various polymers [5] or on Tg and Tm (melting temperature) of aromatic polymers [6]. Above a characteristic chain length polymer chains may (depending on the rigidity of the polymer backbone and/or on processing (stretching)) undergo the formation of entanglements. These entanglements mainly govern rheological properties and several mechanical (viscoelastic) properties. A less known, and indirect, effect of such entanglements is a lowering of ‘‘pure’’ thermal stability of polymers as compared with corresponding lower mass compounds (non-entangled). As an example, in absence of oxygen, linear polyethylene starts degrading at about 3001C, while hexadecane can resist up to 5001C [7].
3.2 End groups A useful relationship can be written between molecular mass and end group concentration for linear polymers. Indeed, as there are exactly two end groups Table 2
Influence of chain length on melting point, T, of aliphatic compounds H–(CH2)n–H
n
Name
Melting T (1C)
1 2 3 4 5 6 8 10 12 18 30 EN
Methane Ethane Propane Butane Pentane Hexane Octane Decane Dodecane Octadecane Triacontane Polyethylene
182.4 182.8 189,9 138.3 129.7 95.0 56.5 29.7 9.6 28.0 65.5 110–135
28
Jacques Devaux and Sophie Demoustier-Champagne
per chain (of n units), their concentration [EG] can be written as: ½EG ¼
2 Mn
End group quantification is thus a useful method for number average molecular mass determination. Also, if the end group concentration is higher than the value calculated from an independent Mn determination, chain branching can be deduced and quantified. Jackson and Robertson consider the molecular structure characterisation and analysis of polymer end groups in Chapter 5.
3.3 Chain substituents The nature of the chain substituents strongly influence the properties of the resulting polymer. For instance, the influence of the nature of chain substituents on Tg is illustrated in Table 3 for a series of vinyl polymers.
3.4 Spatial arrangements In addition to the type, number and sequential arrangement of monomers along the chain, the spatial arrangement of substituent groups plays also an important role in determining the polymer properties. Table 3
Influence of chemical nature of substituents on Tg
Structure
C C H2 H2
Glass transition (Tg)1C
Polyethylene
B100
Polypropylene
15
Polyvinyl chloride
+80
Polystyrene
+100
n
C CH H2 n CH3
C CH H2 n Cl
C CH H2
Name
n
Polymer Chemistry and Microstructure
29
CH3 C H2
C
C H2
CH3 CH3 H2 H2 H2 C C C C C C C C C C H H H2 H2 H
CH3 H C C
CH3 H2 H2 H C C C C C C C C C H2 H H2 H2 CH3
Gutta percha
Natural rubber
Figure 13 Chemical structures of trans and cis isomers of 1,4 polyisoprene (gutta-percha and natural rubber, respectively).
3.4.1 Cis–trans isomerism For polymers with double bonds in the backbone, a first arrangement to consider is the cis–trans isomerism. A well-known example of the influence of this isomerism is found in the natural resins from the saps of hevea (‘‘natural rubber’’) and of sapotacea (‘‘gutta-percha’’). The chemical structures of these materials are, respectively, cis-1,4 polyisoprene for natural rubber and trans-1,4 polyisoprene for gutta-percha (Figure 13). From their properties, mainly that of the chain symmetry allowing the trans isomer to crystallise more easily than the cis isomer, natural rubber achieved its huge commercial exploitation, while uses of gutta-percha remained limited mainly until the end of XIXth century to textile impregnation, and nowadays to golf balls and to dental filling.
3.4.2 Configuration — tacticity Chirality (from ‘‘weir‘‘, hand in ancient Greek) is a property of organic molecules containing at least one carbon atom (or a silicon) with four different substituents. When there is only one asymmetric centre in the molecule, two stereoisomers can be drawn. Along a long chain (considering both sides of the chain as different) carbons (or silicons) bearing two different substituents are considered as asymmetric and two structures (R or S) that would not superimpose can be drawn (Figure 14A). Upon laying out such units along a polymer chain, successive units can be either identical (R,R or S,S) or different (R,S or S,R), giving rise to different stereochemical arrangements of atoms, called configurations. Unlike the conformation, the configuration of a polymer chain cannot be altered without breaking chemical bonds. The general term for the stereoregular configurations is the tacticity of the chain. When all successive asymmetric units exhibit the same configuration, the polymer is said to be ‘‘isotactic’’, when the configurations alternate, the polymer is said to be ‘‘syndiotactic’’; it is ‘‘atactic’’5 when the configurations are randomly distributed along the chain. As illustrated in Figure 14A, three different placements 5
‘‘Heterotactic’’ is sometimes used.
30
Jacques Devaux and Sophie Demoustier-Champagne
H3C
Polypropylene
Poly(methyl-phenyl)silane
A
B
H3C C
C
C C
C
φ
H3C
H3C
H3C
Si
C C
Si
Isotactic
CH3 H3C C
C C
CH3 C
C
C C
φ
H3C
Si
C
CH3 H3C C
C
CH3 C
C
φ
C C
φ H3C
φ
φ
H3C
φ
Si
Si φ CH H3C 3
φ Si
Si
CH3 φ
CH3 H3C
Si
φ
H3C
Si
CH3 φ
CH3
Si Si
φ H3C
Si
Si Atactic
SI
Si
Syndiotactic
φ
H3C
Si
H3C
φ CH3
φ
H3C
Si H3C
H3C
φ
H3C
φ
CH3 φ
Si Si φ H3C
CH3 Si
Si φ
Figure 14 Tacticity of (A) polypropylene and (B) poly(methyl-phenyl) silane.
of the substituents (in the example, H, CH3) are possible. As the vinyl polymers contain only one stereogenic centre every two carbon atoms, the asymmetric carbons are separated by one methylene group. Therefore in an isotactic vinyl polymer, all (identical) substituents are situated on the same side of the plane formed by the extended-chain backbone, whereas they alternate in the case of a syndiotactic vinyl polymer. When each backbone atom is a stereogenic centre, the situation is exactly the opposite, substituents alternating on both sides of the chain plane form an isotactic polymer and non-alternating substituents give rise to a syndiotactic polymer (e.g., Figure 14B is the tacticity of an asymmetric polysilane [8]).
3.4.3 Conformations 3.4.3.1 Definitions. From basic knowledge of chemical bonding, a rather satisfactory representation of the backbone of a hydrocarbon polymer chain is given in Figure 15A. Carbon–carbon bond angles are about 1091 while the ˚. average bond length is 1.52 A However, this representation, while giving a good idea of the linearity of the chain, and of bond lengths and angles, remains limited to the particular situation where all the backbone atoms are located in the plane of the paper (the so-called ‘‘extended chain’’ or ‘‘planar zig-zag’’ situation). Indeed, while maintaining lengths and angles internal rotations around single bonds allows one to
Polymer Chemistry and Microstructure
H2 C
A
C H2
H2 C C H2
H2 C C H2
Energy
H3C
H2 C C H2
H2 C C H2
H2 C C H2
H2 C C H2
H2 C C H2
31
H2 C C H2
H2 C C H2 CH3
Gauche
Gauche
B Eclipsed
Eclipsed Trans = "zig-zag"
0°
180°
360° Angle
Figure 15 (A) Polyethylene chain in planar zig-zag conformation. (B) Energy diagram of n-butane as a function of ‘‘chain’’ rotation.
realise a large number of different geometrical arrangements, which are called ‘‘conformations’’. Conformations are defined as ‘‘non-identical arrangements produced by the rotation of backbone atoms around one or more single bonds’’. The different conformations are easily understood by reference to simple molecules like ethane or butane for a rotation around the central carbon–carbon single bond. ‘‘Eclipsed’’ and ‘‘staggered’’ conformations refer to the situations where two identical substituents on both central carbon atoms are aligned, or non-aligned (rotation of 601), respectively. Of course, depending on the size and shape of the substituents, all conformations are characterised by a slight energy difference. The lowest energy conformation of a linear molecule with more than four backbone atoms is always the planar or ‘‘trans’’ conformation (like the example in Figure 15A). Two other low-energy conformations are obtained by a clockwise or counter-clockwise rotation of the central bond of 1201 (Figure 15B). The two staggered conformations are said to be ‘‘gauche’’ and are skewed and non-planar. Energy differences between conformations remain, however low and, in most cases, less than the thermal energy, allowing almost free rotation around carbon–carbon single bonds at room temperature, hence, the average conformation of a polymer chain in a liquid (melt or solution) or amorphous state is a ‘‘random coil’’ (or ‘‘statistical coil’’).
3.4.3.2 Ordered conformations. As explained above, the mean conformation of a polymer chain in the amorphous state is near to being a random coil. Situations where an isolated molecule displays a highly ordered arrangement are rather uncommon. It can however result from intramolecular bonding and strong interactions. An example can be found in p-phenylene polyamides (see, e.g., Figure 16) where the phenyl groups are planar and therefore rotation around the C–N bond is restricted due to electron delocalisation. Such molecules are
32
Jacques Devaux and Sophie Demoustier-Champagne
O
O
C
C
N
N
N
H
H
H
O
O
C
C
O
O
C
C
N
N
N
H
H
H
O
O
C
C
Figure 16 Chain structure of poly(p-phenylene terephthalamide) (Kevlars).
consequently asymmetric and are best visualised as long thin rods, explaining why they often behave as liquid crystals in solution. An increase in rod-like arrangement of the macromolecules can also arise by stretching a polymer either in its solid state, either in the melt or even in solution (for polymers leading to lyotropic liquid crystals such as aromatic polyamides). This is the basis of the development of synthetic fibres including high modulus polyethylene Dyneemas, polyamide Nylonss and Kevlars, polyester Tergals or Dacrons fibres. Stretching a polymer in two perpendicular directions, either successively or by blowing a bubble of molten material, leads to its biaxial orientation, which strongly improves mechanical properties in the stretching directions and/or gas permeability (e.g., biaxial orientation of polypropylene leads to BOPP (for biaxially oriented polypropylene) or biaxial orientation of poly(ethylene terephthalate) gives CO2-impermeable bottles for carbonated beverages.) (Characterisation methods for determining molecular orientation are considered in Chapter 8.) The most important way of ordering linear molecules remains however crystallisation (Section 2.3.2). In crystals, the most common conformations are those that minimize energy, for instance planar zig-zag in polyethylene. Usual intermolecular forces (van der Waals interactions, hydrogen bridges, dipole–dipole interactions) can be responsible for polymers maintaining preferred chain conformations more or less ordered as quasi-linear extended chains in crystal lattices. Hydrogen bridges occur in both the crystal phase and the amorphous (or liquid) phase of polyamides like Nylonss and are responsible for their high-melting enthalpy, hence high-melting point. They are responsible for the higher thermal properties of polyamides compared to the corresponding polyesters. Hydrogen bridges also play a prominent role in celluloses and in proteins by maintaining preferred arrangements able, for instance, to catalyse biological reactions (enzymes). In hydrocarbons like polyethylene, interactions in the crystal phase are weaker and of the van der Waals type. Dipole interactions are important in PVC as a consequence of the C–Cl bonds. In some cases, planar chain structures become impossible when replacing a hydrogen atom on the backbone of a macromolecule by a bulky group. Packing problems arise due to steric hindrance if the trans orientation of each bond is
Polymer Chemistry and Microstructure
33
: CH3 :C :H
Figure 17 Helical structure of isotactic polypropylene. (See Color Plate Section at the end of this book.)
maintained, which becomes eventually less energetically favourable than the gauche conformation. Hence, other rotational angles or a succession of rotational angles must be adapted as, for instance, in a helix (x/y)6 conformation, which, in the general case, is realised by the repetition of a trans-gauche sequence. The same gauche angle must always occur. As there are two possibilities, righthanded and/or left-handed helices can form. Examples are isotactic polypropylene (a 3/1 helix) (Figure 17), polytetrafluoroethylene (e.g., Teflons) where a 13/1 helix is found, or polyisobutylene arranged in a 8/5 helix. Helices can be included in crystal lattices.
6
An x/y helix is a helix with x repeat units in y turns.
34
Jacques Devaux and Sophie Demoustier-Champagne
4. FUNDAMENTALS OF POLYMER CHEMISTRY 4.1 Chain polymerisation vs. step polymerisation It is not the purpose of this chapter to describe in detail the synthetic chemistry of polymers. From the early ‘‘Principles of polymer chemistry’’ book of Flory, the first edition of which dates from 1953 [9], numerous other books have been written on the subject, among which a few examples are referenced [3,10,11]. In addition to biological reactions, there are two main mechanisms of building synthetic polymers from their monomers: addition (or chain) polymerisation and step polymerisation. Schematically, synthesizing a polymer can be compared to playing dominos. On the one hand, it can be done by aligning a long series of them on their smallest face, then, by a small push on the first one (initiation), inducing a concerted falling down (propagation). On the other hand, dominos can be arranged in long series by associating corresponding ends step by step, like functional molecules by reacting corresponding functions. A major difference between both kind of syntheses lies in polymerisation kinetics: in the former case there is a chain mechanism (initiation, propagation, termination), in the latter case there is no chain reaction and each step is equiprobable. Main comparison points are highlighted in Table 4 [9]. For both types of polymerisation mechanisms, different polymerisation processes can be used ranging from simple bulk and solution polymerisation processes to more sophisticated ones such as suspension, emulsion, interfacial, plasma,y polymerisation processes.
Table 4
Comparison between addition and step polymerization
Chain polymerisation (addition polymerisation)
Step polymerisation (polycondensation)
Only growing species add units one at a time Monomer concentration decreases steadily throughout reaction Long chains formed at once Molecular mass changes little throughout reaction The longer the reaction time, the higher the yield Reaction mixture contains: monomer high polymer E104 part of active species
Any two molecules can react Monomer almost disappears early during reaction Molecular mass increases all along reaction The longer the reaction time, the higher the molecular mass Distribution of all species can be calculated all along the reaction
Polymer Chemistry and Microstructure
35
4.2 Types of chain polymerisations and polymers synthesized — keypoints of mechanisms, kinetics Addition polymerisation is mainly characterised by the existence of a chain mechanism. This means that the process of building the chain is always based on the sequence: initiation - propagation - termination. A long chain (high) polymer is only obtained if the propagation step is much faster than the initiation and/or termination7 reactions. Therefore, during the synthesis, a very limited amount (or number) of active species can actually react at a given instant. Moreover, the lifetime of these active species is often shorter than the total duration time of the reaction. Long terminated (non-reactive) chains thus coexist with monomer molecules throughout the reaction. Disregarding the actual chemical mechanism of each monomer reaction, a good example of polymers made by chain reactions are the vinyl polymers (by definition, polymer made from monomers having the vinyl group: CH2QCH–, as the reactive group). Formulae of some typical vinyl polymers were reported in Table 1. Chain polymerisations are often classified on the basis of their elemental reaction type as: Radical chain polymerisation Ionic chain polymerisation Transition metal insertion polymerisation. Each of these leads to particular characteristics of the polymer chain. Each will be briefly discussed in the following sections, with a special focus on the viewpoint of characterisation.
4.3 Radical chain polymerisations 4.3.1 Free radical polymerisation A schematic representation of the principal steps (initiation, propagation and termination) of a radical chain polymerisation is presented in Figure 18.
4.3.1.1 Initiation. Initiation in radical polymerisation consists of two steps: the dissociation of the initiator to form two radical species, followed by addition of a single molecule to the initiating radical (Figure 18). Initiators include any organic compound with a labile group, such as an azo (–NQN–), disulfide (–S–S–) or peroxide (–O–O–) compound. The labile bond can be broken by various ways like heat, UV light, g-irradiation or by a redox reaction. 4.3.1.2 Propagation: head-tail. As usually considered, a propagation reaction leads to the addition of a monomer molecule, with the same linear orientation as
7
When there is a termination reaction.
36
Jacques Devaux and Sophie Demoustier-Champagne
I R
2R +
H H2C C
H R C CH C C H2 H2 n
R
+
H C C H2
Initiation
H H2C C
H R C CH C C H2 H2 n+1
Propagation
H R C CH C C H2 H2 n
+
C C C C R H H2 H H2 n
R C CH C CH C C C C R H2 H2 H H2 H H2 n n
by addition
by disproportionation
Termination
R
H C CH C C H2 H n
+
C C C C R H2 H2 H H2 n
Figure 18 Mechanism of radical chain polymerisation of styrene.
the previous unit to the growing radical (head-to-tail addition). The main reasons invoked to justify this behaviour are: head-to-head addition would lead to less stable radicals (case of PS), head-to-head addition is unfavourable due to steric hindrance (case of poly(vinyl acetate)), the polarity of the substituent of the vinyl moiety orients the addition to headto-tail (case of PVC).
Polymer Chemistry and Microstructure
37
Monomer addition under radical propagation conditions leads to mainly an atactic configuration. As a consequence, radical polymerisations of asymmetric vinyl polymers usually lead to amorphous materials. However, if the substituent is small enough to enter into the crystal cell, atactic vinyl polymers can crystallise (an example is poly(vinyl fluoride)).
4.3.1.3 Kinetics of radical chain polymerisation. Kinetics calculations on radical chain polymerisation are based on the three steps mechanism with notations as shown in Figure 19. Two main hypotheses are made on radicals to simplify the calculations. 1st hypothesis: Equi-reactivity. The radical reactivity remains independent on the nature or size of the radical. 2nd hypothesis: Steady state. Radical concentration instantaneously reaches and keeps its steady-state value throughout the reaction. The rate of radical formation (rate of initiation, Ri) equals the rate of radical disappearance (rate of termination Rt). d½M ¼ 2Ri 2Rt ¼ 2kd ½I 2kt ½M 2 ¼ 0 (1) dt where [I] is the concentration of initiator, [M ] the concentration of radicals, kd the rate constant of dissociation and kt the rate constant of termination. Using these two hypotheses, the overall rate of polymerisation is simply the rate of chain propagation (Rp). d½M kd 1=2 1=2 ¼ kp ½M ½M ¼ kp f Rp ¼ ½I ½M (2) dt kt where [M] is the concentration of monomer, f the fraction of primary radicals initiating a polymer chain and kp the rate constant of propagation. Equation (2) shows that the rate of radical chain polymerisation is proportional to the monomer concentration and to the square root of initiator concentration.
I M
R
+
Mn
+ M
Mm + Mn
kd ka kp
kt
2R M
Mn+1
Mn+m Mn + Mm
Figure 19 Mechanisms of radical chain polymerisation with kinetic notations.
38
Jacques Devaux and Sophie Demoustier-Champagne
S + Mn S
+ M
I + Mn R
ktrS
M ktrI
+ M
M + Mn M + M
Mn + S
Mn + R M
ktrM
Mn + M M
Figure 20 Transfer reactions in radical chain polymerisation.
4.3.1.4 Chain transfer reactions 4.3.1.4.1 Kinetic vs. material chain. Kinetically, a chain reaction exists throughout the ‘‘life’’ of the radical, that is, from the initiation of a radical up to its termination by recombination or by disproportionation. The lifetime of a radical determines the so-called kinetic chain length Lk defined as the number of monomers consumed per initiating radical. Lk, by definition, can be calculated from the ratio between the propagation rate Rp to the initiation rate Ri, or, using steady-state hypothesis (Equation (1)), from the ratio between propagation rate to the termination rate Rt (Equation (3)). 2
2
kp ½M Rp kp ½M ½M kp ½M Lk ¼ ¼ ¼ ¼ 2 2k Rt ½M 2kt Rp 2kt ½M t
(3)
During the course of radical chain propagation, several types of transfer reaction can occur, leading to the interruption of the ‘‘material’’ chain, while allowing the ‘‘kinetic’’ chain to continue. ‘‘Different’’ end groups can appear as a result of such transfer reactions (Figure 20). In the absence of any transfer, only the type of termination reaction has to be taken into account to obtain the number average degree of polymerisation (or chain length) Xn . Indeed, if the reaction terminates by addition, two radicals give one chain, while if the reaction terminates by disproportionation, one radical generates one chain. Using 0.5oxo1, one obtains Xn ¼
2 2 Lk kp ½M ¼ x 2xkt Rp
(4)
Equation (4) clearly shows that the number average degree of polymerisation Xn is inversely proportional to the reaction rate Rp, meaning that, in radical chain polymerisation high reaction rates are linked to low molecular masses and vice versa. One way to avoid this dilemma is to use emulsion polymerisation where the lifetime of a radical (i.e., the ‘‘kinetic’’ chain length) is independent of
Polymer Chemistry and Microstructure
39
‘‘overall’’ monomer or radical concentrations, but only depends on the number of micelles and on the percentage of time they are ‘‘active’’ (statistically 50%).8 If transfer reactions occur, they terminate ‘‘material chains’’, thus decreasing Xn , without affecting the ‘‘kinetic’’ chain length Lk. Thus Rp P Xn ¼ (5) xRt þ Rtr P with Rtr the sum of all transfer reaction rates. Equation (5) denotes that a control of Xn can be obtained by controlling transfer reactions, that is, by adding calculated amounts of molecules able to transfer a radical thus creating new end groups. 4.3.1.4.2 The low-density polyethylene and polypropylene cases. In the course of the radical chain polymerisation of ethylene two kinds of transfer on the polymer play a major role, giving rise to LCB or SCB. These are illustrated in Figure 21. Due to both kinds of branching leading to chain irregularities, the crystallisation of radical chain-polymerised polyethylene is strongly hindered. Its maximum degree of crystallinity is limited to about 50%, its melting temperature ranges from 801C to 1151C and its density remains low (B0.92). From this latter property, it received the name of low-density polyethylene (LDPE). In radical chain polymerisation of allylic monomers (containing the chemical allyl group CH2QCR–CH3, like propylene, isobutylene,y), a transfer on the monomer can occur leading to a very stable allyl radical unable to propagate the chain. Thus radical chain polymerisation of such monomers, especially propylene is not feasible, as a competition exists between the propagation rate and the high rate of transfer on the monomer (see, Figure 22). 4.3.1.4.3 Termination reactions 4.3.1.4.3.1 LOW VISCOSITY (LOW CONCENTRATION SYSTEMS). Radicals are species that normally have short lifetimes (102 s to 10 s). In the course of a chain growth mechanism (see Figure 18) they terminate by finding a second non-paired electron to build a chemical link made of an electron pair. This requires that two radicals meet, either to pair their electrons and combine (addition) or to exchange a hydrogen, leading to the formation of one saturated bond and one double bond (disproportionation). 4.3.1.4.3.2 GEL OR TROMMSDORF EFFECT, VITRIFICATION AND LIVING RADICALS. When the initial monomer concentration is high (X40%), the viscosity of a system increases upon increase of the conversion. This increase is linked to progressive interpenetration of coiled macromolecules, leading to entanglement. Due to this viscosity increase, the mobility of the molecules, mainly the longer ones (growing radicals) decreases and the kinetics may be affected by slower diffusion. This effect is first noticeable for reactions involving two large reactive molecules, that are the termination reactions. Therefore, as the initiation reaction is less affected, the steady-state hypothesis is no more valid and the radical lifetime increases, 8
Due to the very small (nanometric) size of a micelle, only one radical at a time can exist inside.
40
Jacques Devaux and Sophie Demoustier-Champagne
Long Chain branching
CH
+
CH2
C H2
n H 2C
+
H2 C
CH2
CH
+
CH3
H 2C
H 2C
H2 C
CH 2
LCB
CH C H2 H 2C
H 2C
Short Chain branching
H2 C
CH
H H2C
H2 C
H2 C C H
CH2 CH2
H 3C
H2 C
H2 C
H2 C
C H
CH2
CH 2 CH 2
CH2 H 3C
+
n H 2C
CH2
H2 C
CH
H2 C
H2 C C H2
C H2
(CH2)3 CH3
SCB
Figure 21 Transfer reactions in radical chain polymerisation of ethylene.
together with their concentration (Equation (1)), leading to an auto-acceleration of the overall polymerisation reaction. As this phenomenon is due to entanglement of coiled chains and a large increase of viscosity, it is called, somewhat improperly, the ‘‘gel effect’’ (even if there is no true ‘‘gel’’ because there is no crosslinking). It is also sometimes named the ‘‘Trommsdorf effect’’ [3]. Such effects are especially observable when polymerisation occurs in the bulk (mass polymerisation). In this case, another effect can be observed at high
Polymer Chemistry and Microstructure
R
+
R
C C H2 H
H2 C
C H
CH3
CH3
+
H 2C
R
C H
C C H2 H
CH3
R
C C CH3 H 2 H2
41
CH3
R
C CH C C H2 H2 H CH3
CH3
H 2C
C H
CH2
H 2C
C H
CH2
+
stable allyl radical unable to propagate
Figure 22
Transfer reactions inhibiting propylene radical polymerisation.
conversion. If the final synthesized polymer is characterized by a Tg higher than the actual temperature at which the polymerisation reaction is carried out, it happens that the Tg of the system, which increases with the conversion degree, reaches the reaction temperature. At this point, the whole reaction medium vitrifies and the molecular mobility vanishes, stopping the reaction without termination, at a monomer conversion below 100%.
4.3.2 Controlled/Living radical polymerisation Recently, controlled/living systems based on radical mechanism have been reported [12,13]. The new concept for controlling chain growth processes relies on forming an equilibrium between active species (radicals) and various types of dormant species. Very small amounts of the active species equilibrate with the dormant species, slowing down the rate of polymerisation and allowing tolerance to impurities. There are three approaches to the exchange process. Two of them are based on the persistent radical effect and are spontaneous (nitroxide-mediated polymerisation, NMP) or catalysed (atom transfer radical polymerisation, ATRP). The third approach uses a degenerative transfer mechanism with either alkyl iodides or dithioesters (reversible addition fragmentation transfer, RAFT) as transfer agents [12]. These new synthetic polymerisation processes provide efficient routes to precisely control molar mass and its distribution, macromolecular architecture as well as microstructure (tacticity and sequencing). Controlled/living radical polymerisation (CRP) is currently a fast developing area in polymer synthesis and it allows preparation of many advanced polymeric materials, including thermoplastic elastomers, surfactants, gels, coatings, biomaterials, materials for electronics and many others.
42
Jacques Devaux and Sophie Demoustier-Champagne
4.4 Ionic polymerisations — active species Ionic chain polymerisations refer to chain mechanisms in the course of which the propagation step consists of the insertion of a monomer into an ionic bond. The strength of this ionic bond can vary, depending on the nature of the species, the temperature and the polarity of the solvent, between a closed ionic pair in contact up to free ions (see Figure 23). Final polymer microstructure (configuration,y) and molecular mass distribution depend on the actual nature of the active ionic species. Ionic chain polymerisations follow the same basic steps as radical chain polymerisation and are said to be either cationic or anionic depending on the nature of the ion formed in the initiation step. Schemes of the insertion during the propagation step in cationic and anionic chain polymerisations are shown in Figure 24. Polymerisation of vinyl monomers with electron-donating substituents can proceed by a cationic mechanism, while monomers with electron-withdrawing group can polymerise by an anionic pathway.
4.4.1 Cationic polymerisation A cationic polymerisation mechanism is illustrated in Figure 25 for the most industrially important example of polyisobutylene. Unlike radical chain polymerisation, initiation in cationic polymerisation uses a true catalyst that is recovered at the end of the polymerisation and is not incorporated at one end of the growing chain. Catalysts for cationic chain polymerisation are molecules able to withdraw electrons, mainly Bro¨nsted (H2SO4, H3PO4) and Lewis acids (BF3, AlCl3, SnCl4). The choice of solvent for cationic polymerisation is also important because it plays a major role in the association between cation and counter ion. A too tight association will prevent monomer insertion during the propagation step. However, the use of ‘‘stabilized’’ A
B
n
n A
Aδ(+)
B
Bδ(−)
aggregate
A+B−
A+//B−
ion pair solvated ion pair
A+ + B− free ions
Figure 23 Active species in ionic polymerisations. cationic A
H2 + C CH C CH B− H2 n R R
+
H2C
CHR
A
+
H2C
CHR
B
H2 + C CH C CH H2 n+1 R R
B−
anionic B
H2 − C CH A+ C CH H2 R n R
Figure 24 Schemes of propagation steps in ionic polymerisations.
H2 − C CH C CH A+ H2 n+1 R R
43
Polymer Chemistry and Microstructure
CH3 F3BOH OH +
Initiation
+ H2C
C
CH3
ki
H 3C
CH3
CH3 CH3 H2 C C + F3BOH C C H2 n CH3 CH3 CH3
CH3
Propagation
H3C
C
CH3
- + HC 2
H 3C
kp
CH3 CH3 H2 C C + F3BOH C C H2 n CH3 CH3 CH3
C
-
CH3 H 3C
CH3 CH3 H2 C C + F3BOH C C H2 n CH3 CH3 CH3
kt
C
Transfer to monomer
CH3 CH3 H2 C C + F3BOH C C H2 n+1 CH3 CH3 CH3
C
CH3 CH3 H2 C C OH C C H2 n CH3 CH3 CH3
C
C
+
BF3
ktr
CH3
CH2 CH3 H2 C C C C H2 n CH3 CH3 CH3
C
-
CH3
H 3C
CH3
CH3
H 3C
-
CH3
H 3C
CH3
- + HC 2
F3BOH
CH3
CH3
CH3
Termination
C
C+
+
H 3C
C+
F3BOH
-
CH3
Figure 25 Overall cationic chain polymerisation mechanism of isobutylene.
carbocation sites allows the cationic chain polymerisation to be undertaken under ‘‘living’’ conditions at low temperatures, where termination and transfer reactions are almost suppressed [13]. Typical termination can occur by deactivation of the cationic species from the growing chain, possibly leading to a functional end group (Figure 25). Transfer reaction to the monomer, leading to the insertion of an unsaturated end group, is an important reaction in cationic chain polymerisation. As the activation energies of both termination and transfer reactions are higher than that of the propagation step, cationic chain polymerisation can only lead to high molecular masses when undertaken at low temperatures, typically 1001C. Commercial polyisobutylene is often copolymerised with a few percentage of isoprene in order to allow for crosslinking (butyl rubber).
4.4.2 Anionic polymerisation Anionic polymerisation mechanism is illustrated in Figure 26 with the example of styrene polymerisation. The active species in anionic chain polymerisations are anionic growing chain ends. The main characteristic of such a process is the almost total absence of termination and transfer reactions. For this reason, anionic polymerisation is often called ‘‘living polymerisation’’.
44
Jacques Devaux and Sophie Demoustier-Champagne
Initiation C4H9-
+ Li
+
H 2C
H C
C4 H9
- + C CH Li H2
Propagation
H2 C CH C H2
-+
CH n-1
Li
+
H2 C
H C
H2C CH C H2
-+
CH Li n
NO TERMINATION
Figure 26 Overall anionic chain polymerisation mechanism of styrene initiated by n-butyllithium.
Initiators are species able to transfer either an electron or an electron pair to the monomer: Bro¨nsted or Lewis bases, or, most often, organometallic derivatives like alkyllithium (very strong bases) are used. Note that in this case the initiating species (e.g., the n-butyl group) is incorporated as an end group in the polymer chain. When the initiation step is very fast (almost instantaneous), the absence of termination during living polymerisation can lead to a very narrow molecular mass distribution. Therefore, anionic chain polymerisation is often used to synthesize monodispersed samples used as standards for size exclusion chromatography (SEC) (see Chapter 6 for discussion of SEC). In the absence of termination reactions each monomer has an equal probability of fixing to an anion site. Therefore, the number averaged degree of polymerisation is simply equal to the ratio of initial monomer concentration to initial initiator concentration. In anionic polymerisation the molecular mass increases linearly with the conversion of the monomer [14]. During the propagation step, depending on the nature of the active ionic species, a limited control on the tacticity of the final polymer is possible. Ion pairs can, indeed, require the insertion of the monomer under a defined orientation, while free ions are unable to orient the insertion. If the starting reagents are pure and if oxygen and traces of water are excluded from the reaction, propagation can proceed indefinitely or until all the monomer is consumed. However, introducing selected additives to react with active anionic end groups allows one to either functionalize the chain end, or to start a new polymerisation of the same or of another monomer, leading to building of block copolymers. Typical functionalisation of end groups are listed in Table 5.
45
Polymer Chemistry and Microstructure
Table 5
Typical end-functionalisation reactions in anionic chain polymerisation
End-functionalisation reaction
Functional end group
C
+ O2
C
O
C
+ CO2
C
C
O
O O
C
+
H2C
CH2
C
O
C H2
C
+ H2O
C
H
C
+
C
H
RH
H2 C
O
+ OH
+ R
4.5 Olefin polymerisation processes With the exception of LDPE, polyolefins like other polyethylenes and polypropylene, which represent the largest amount of vinyl-type polymers produced in the world, are neither synthesized by radical nor by classical ionic polymerisation processes. Different types of polymerisation catalysts are in use for these purposes. The Cr-based Phillips catalyst, Ziegler–Natta type catalysts, metallocene or other more recently discovered catalysts, including late transition metal catalysts, are all characterized by their propagation step where the olefin monomer inserts into a carbon-transition metal link.
4.5.1 Phillips process The Phillips process can be used for the synthesis of polyethylene only. It makes use of a Cr-based heterogeneous catalyst on the surface of which the chain grows on metallic atoms of low oxidation level (CrII). Termination and transfer reactions in the Philips process both lead to unsaturated end groups, which results in chains having one saturated and one unsaturated end group (Figure 27).
46
Jacques Devaux and Sophie Demoustier-Champagne
Figure 27 Propagation, termination and transfer reactions in ethylene polymerisation by the Phillips process.
A major characteristic of the Phillips process chain polymerisation of ethylene is that it leads to very limited branching. The resulting polymer is thus highly linear and can reach high levels of crystallinity, hence high densities approaching 0.96–0.97. Such a polyethylene is known as HDPE for ‘‘High-density polyethylene’’.
4.5.2 Ziegler–Natta process The naming ‘‘Ziegler–Natta’’ given to processes for polyolefin syntheses originates from the use of Ziegler-type catalysts and in their use by Natta for isotactic propylene synthesis. They are based on heterogeneous catalysts made from complexes of group I–III organometallic compounds (or hydrides) and compounds of a group IV–VIII transition metal. Typical initiators of Ziegler– Natta polymerisation process are listed in Table 6. A common catalyst is the complex a-TiCl3–AlR3. The chain grows by insertion of the olefin molecule into the Ti–C link. The main characteristics of most of these heterogeneous catalysts is that, due to the size and shape of the complex, the insertion is only possible for one particular spatial orientation of the monomer, which, in the case of an asymmetric monomer like propylene, leads to a good control of tacticity. While use of Ti-based catalyst can lead to isotactic polypropylene, syndiotactic polypropylene is obtained using V-based catalysts. Ziegler–Natta catalysts were also designed to synthesize polyethylene (HDPE) and copolymers of ethylene with longer chain a-olefins (n-butene,
Polymer Chemistry and Microstructure
Table 6
47
Examples of typical components of Ziegler–Natta initiators
Group I–III metal
Group IV–VIII transition metal
(C2H5)3Al (C2H5)2AlCl (C2H5)AlCl2 (C2H5)2Be C4H9Li C5H11Na
TiCl3 TiCl4 TiBr3 VCl4 Ti(OC4H9)4 ZrCl4
Figure 28 Hydrogen transfer reaction in propylene polymerisation by the Ziegler–Natta process.
n-hexene, n-octene,y), to introduce controlled amounts of SCB and a limited crystallinity. These polymers are known as linear-low density polyethylene or LLDPE. The importance of Ziegler–Natta processes result from their broad synthesis range possibilities.
Isotactic polypropylene9 HDPE and LLDPE Ethylene — propylene copolymer (ethylene–propylene rubber or EPR) Polybutadiene (PB) and polyisoprene with cis–trans controlled microstructure (synthesis of ‘‘natural rubber’’).
The termination of Ziegler–Natta synthesis is obtained by neutralisation of the catalytic site using, for instance, alcohol. The reaction can also simply be stopped (with no clear termination) by embedding of the catalyst into the polymer. Industrially, the control of final molecular mass is often accomplished by a hydrogen transfer reaction (see Figure 28).
4.5.3 Metallocenes and others Based on an early process discovered by Natta in the 1950s, soluble transition metal catalysts like metallocenes were developed mainly in the 1950s as initiators for polyolefin syntheses. Others are still now under investigation, like the so-called LTM (for ‘‘late transition metal’’) catalysts. Metallocenes seem 9
This result led to Ziegler and Natta jointly receiving the Nobel Prize for Chemistry in 1963.
48
Jacques Devaux and Sophie Demoustier-Champagne
Typical metallocenes:
Proposed MAO structures:
CH3
H3C Al
O
Al
CH3 O
CH3
H3C Al
Al
O
Al
CH3 O
Al
CH3
H3C
m
n O
Figure 29 Structures of typical metallocenes and proposed structure of methylaluminoxane (MAO).
potentially even more versatile than Ziegler–Natta catalysts as they retain their internal chiral site due to their ‘‘sandwich’’ structure. There are numerous available molecular structures of metallocenes on the basis of Ti, Zr, Hf, Yb and other transition metals. To act as a polyolefins’ synthesis catalyst, they need to be activated by a co-catalyst, for example, by methylaluminoxane (MAO), which is used in high excess by comparison with the metallocene. Typical structures of a few metallocenes and of MAO are reported in Figure 29. Polyolefins obtainable through the use of metallocene catalysis include isotactic, syndiotactic, and atactic polypropylenes, polyethylenes and copolymers including polar comonomers. A characteristic of polyolefins synthesized with metallocene catalysts is their significantly lower polydispersity compared to one obtained by using heterogeneous Ziegler–Natta catalysts. Such narrower molecular mass distributions can lead to different mechanical properties of the resulting material.
4.6 Processes for polyolefin syntheses Table 7 shows synthesis processes and microstructures of available polyethylenes together with several of their properties.
Table 7 Synthesis processes and microstructures of polyethylenes with characteristic properties Structure data
HDPE Phillips (Ziegler–Natta) 0.96–0.94(0.95) 94 (80–87) 128–135 1.3 (4) 1.2 (0.6)
LLDPE Ziegler–Natta 0.915–0.93 46–60 120
LDPE Radical chain polymerisation 0.915 – 0.93 46–60 110 25 0.6
Polymer Chemistry and Microstructure
Abbreviation Synthesis Typical density Percentage crystallinity range Melting range (1C) –CH3/1,000 carbons –vinyl/1,000 carbons
49
50
Jacques Devaux and Sophie Demoustier-Champagne
4.7 Copolymers 4.7.1 Linear copolymers On the basis of the kinetic characteristics of chain polymerisation reactions, it is possible to predict the final microstructures available by a so-called random process from a simple mixture of two comonomers. Indeed, the global mechanism of copolymerisation can be illustrated as presented in Figure 30. From this kinetic scheme, two characteristic parameters can be defined, r1 and r2 r1 is a measure of the ratio between the rate of addition of monomer 1 to the rate of addition of monomer 2 on a growing radical terminated by monomer 1, while r2 is the ratio between the rate of addition of monomer 2 to the rate of addition of monomer 1 on a growing radical terminated by monomer 2. r1 ¼
k11 k12
r2 ¼
k22 k21
The composition of the copolymers as a function of the composition of the mixture of monomers can be best understood from the practical example of styrene and methyl methacrylate (MMA) as shown in Figure 31. For radical chain copolymerisation of styrene and MMA, r1Er2o1. The copolymer content in styrene is not very different from the monomer kd
I
2R
ka1
R + M1
ka2
R + M2
M2
k11
M1 + M1
k12
M1 + M2
k21
M2 + M1
k22
M2 + M2
M1 +
M1
M1 +
M2
M2 +
M2
Initiation
M1
kt11 kt12 kt22
M1
+ M1
M1
+ M2
M2
+ M1
M2
+ M2
Propagation
copolymer
copolymer
Termination
copolymer
Figure 30 Mechanism of ‘‘random’’ chain copolymerisation of two comonomers (M1 and M2).
Polymer Chemistry and Microstructure
51
Copolymer: fraction of styrene
1
Cationic
0.8
0.6 Radical
0.4
0.2 Anionic 0 0
0.2
0.4
0.6
0.8
1
Monomer mixture : fraction of styrene
Figure 31 Copolymer composition as a function of monomer mixture composition in the case of styrene methyl methacrylate mixtures. Reproduced from Mercier and Mare´chal [15], Reproduit avec l’autorisation de l’e´diteur. Tous droits re´serve´s.
composition and does not change a lot during the course of the copolymerisation, nevertheless the slight difference between r1 and r2 prevents the composition following a straight line (diagonal if r1 ¼ r2 ¼ 1). In the case of cationic copolymerisation of styrene and MMA, r1 r26¼1 and r1W1 and r2o1. As it adds faster, the styrene content in the copolymer is always higher than in the monomer mixture, where it decreases throughout the reaction. The styrene content in the copolymer decreases thus also throughout the reaction. However, in the anionic copolymerisation of styrene and MMA, r1 r26¼1 and r1o1 and r2W1. As it adds slower, the styrene content in the copolymer is always lower than in the monomer mixture. In summary, the copolymer composition depends on the monomer ratio in the monomer mixture and on r1 and r2 reactivity ratios.
4.7.2 Graft copolymers An important class of copolymers copolymers, synthesized in order to of a rubber phase. Examples are the for High-Impact PolyStyrene and Both are synthesized in two steps.
made by chain copolymerisation is graft toughen brittle materials through inclusion cases of styrenic copolymers called ‘‘HIPS’’ ABS for Acrylonitrile–Butadiene–Styrene.
First step: radical polymerisation of butadiene in the presence of a chain transfer agent to control its molecular mass. Second step: polymerisation of styrene (to get HIPS) or styrene and acrylonitrile (to get ABS) with partial grafting of PS or SAN (styrene/ acrylonitrile) sequences onto the PB chains.
52
Jacques Devaux and Sophie Demoustier-Champagne
Addition ("grafting to")
Mn
M n• or
+
C C H2 H
C H
C C H2 H or
C H2
• C H
C H2
• C CH C H2 H R
R•
C H2
Transfer & grafting ("grafting from")
Mn • or
MnΗ +
C C H2 H
R•
C H
C H2
C C H2 H or
or
C H
RΗ
• C H
C H
C H
• C H
• C H
C H2
•
Mn + nM
C H
Figure 32 Grafting mechanisms in styrenic graft copolymers.
Figure 32 shows the mechanism of grafting involved, including the grafting (addition) of growing chains onto the butadiene double bonds (sometimes referred to as ‘‘grafting to’’) and transfer of the radical to the butadiene followed by the growing of a new chain from this transferred radical (sometimes referred to as ‘‘grafting from’’). The succession of both mechanisms may lead to crosslinking.
4.7.3 Block copolymers Another important class of copolymers synthesized by chain polymerisation are block (or sequenced) copolymers; diblock and triblock copolymers being the most important ones. They are very useful as compatibilisers (emulsifiers) in immiscible polymer blends. Another major use is as thermoplastic elastomers. Both uses are best explained through the example of butadiene–styrene block copolymers. PS and PB homopolymers are immiscible. Any added PB–PS block copolymer in a PS–PB blend will have one sequence miscible in PS and one sequence miscible in PB, hence they will localise at the interface. As a consequence, the interfacial energy will decrease, greatly helping dispersion and providing phase adhesion, thus a transfer of mechanical properties. In a pure PB–PS block copolymer, both sequences are immiscible and the microstructure will be diphasic (at a supramolecular or nanoscopic level). If the ratio is such that PS particles are dispersed into a matrix of PB, below the Tg of PS, the system behaves like crosslinked PB, hence as an elastomer. However, above the Tg of PS, the system becomes viscous and can be processed like a thermoplastic.
Polymer Chemistry and Microstructure
A Spheres
A Cylinders
AB Lamellae
B Cylinders
53
B Spheres
Figure 33 Available morphologies in biphasic sequenced copolymers.
Synthesis of vinyl block copolymers is accomplished by living polymerisation, mostly by anionic polymerisation. Several strategies can be used, illustrated here by the example of the Styrene–Butadiene–Styrene (or SBS) triblock copolymer. Synthesis of a PB sequence with two living ends, using a difunctional initiator, followed by the addition of styrene to build two sequences of PS (two steps). Synthesis of a PS sequence with one living end, adding and polymerising butadiene, while keeping its living end, then adding a new amount of styrene to build the third sequence (three steps). Sequential synthesis of a diblock styrene–butadiene copolymer, while keeping the living end onto the butadiene end. Then coupling the living end groups by a suitable bifunctional agent (e.g., COCl2) (three steps). Making use of the higher reactivity of butadiene in anionic polymerisation (r1o1, r2 W1) to get the triblock SBS copolymer in two steps. The first step is the synthesis of a PS sequence with a living end, then, upon addition of a mixture of styrene and butadiene, butadiene will add first, building a ‘‘pure’’ PB sequence, and styrene will finally build the third sequence (two steps).
4.7.4 Links with microstructure (phase diagrams) Copolymers (graft or block) made of immiscible sequences give rise to biphasic morphologies depending on the ratio of immiscible sequences (or of their lengths). Such possible microstructures are reported in Figure 33. A minor phase can be dispersed as nodules (spheres) or filaments (cylinders) while, when concentrations of both phases get similar, lamellar (interpenetrated) structures can appear. It should be noted that rather similar morphologies could also be found in (compatibilised) polymer blends.
4.8 Types of step polymerisations and polymers synthesized — keypoints of mechanisms, kinetics 4.8.1 Step polymerisation vs. polycondensations The most important difference between chain and step polymerisations is the absence of a kinetic chain in the latter. Among the different chemical reactions usable to synthesize polymeric materials by step polymerisation are esterification, amidation, nucleophilic aromatic substitution and urethane (carbamate) formation. Polymerisation
54
Jacques Devaux and Sophie Demoustier-Champagne
usually proceeds by the reactions between two different functional groups, for instance, hydroxyl and carboxyl (to get esters), amino and carboxyl (to get amides), hydroxyl and halogen (to get ethers) or isocyanate and hydroxyl groups (to get carbamates or urethanes). The type of reactions involved also leads to use (sometimes improperly) of the terms polycondensation and polycondensates for step polymerisation and polymers made by them, despite there not always being a condensable small molecule among the by-products.
4.8.2 Monomers — ‘‘repeat’’ vs. ‘‘structural’’ units Step polymerizations of linear chains can involve either two different bifunctional monomers in which each monomer possesses only one type of functional group (commonly represented by X–X or Y–Y), or a single monomer containing both types of functional groups (common representation X–Y). However, whatever the monomer type, a linear polymer molecule contains, on average, one functional group of each species per chain (molecule). In order to unify most calculations in step polymerisation a notation, which will be used throughout this section, was introduced by Odian [10], the first step of which is the clear distinction between two definitions. A repeat unit is the sequence of atoms that is repeated to build a polymer chain. This definition, although very simple, distinguishes between X–Y and X–XY–Y units. For instance, the repeat units of polyamide 6 and polyamide 6610 are: O N
C C C C C C H2 H2 H2 H2 H2
H
POLYAMIDE 6 (repeat unit) n
structural unit N H
C C C C C C N H2 H2 H2 H2 H2 H2 H
structural unit
O
O
C
C C C C C H2 H2 H2 H2
POLYAMIDE 66 (repeat unit) n
structural unit
A structural unit or monomer can be defined as the residue from each monomer molecule, whatever its chemical species. In the case of X–Y monomers, a structural unit is identical to a repeat unit (e.g., in polyamide 6), while in the case of X–X, Y–Y monomers, there are two structural units per repeat unit (e.g., in polyamide 66). In the latter case, the mass of a structural unit is obtained by averaging the masses of the two different chemical species. For polyamide 6 and polyamide 66 the masses of structural units are thus 113 in both cases. 10
Polyamides are conventionally named from their number of carbon atoms in structural units with one figure only for X–Y type and two figures (first one for the amine residue, second one for the acid residue) for X–YX–Y type.
Polymer Chemistry and Microstructure
55
A last definition is needed for N (N0 at time 0), which is the total number of molecules present in the system at any time. With the above definitions, N0 initial molecules correspond to N0 monomers and N0 structural units whatever be the chemical species. Each molecule contains on the average one functional group of each kind. Calculations are thus easier and will preferably be performed using structural units.
4.8.3 Carothers equation Assuming p is the conversion ratio equal to the ratio between the actual number of one type of functional group to its initial number N0 N p¼ N0 As there is one functional group of each type per chain, one can write for Xn (number average chain length or degree of polymerisation) Xn ¼
N0 N
Xn ¼
N0 1 ¼ N 0 ð1 pÞ 1 p
or
p¼1
1 Xn
The last equation commonly named the Carothers equation is of general use in step polymerisation. From this equation it can first be deduced that the successful synthesis of high polymers by step polymerisation (i.e., polymers exhibiting molecular mass sufficiently high to be useful for technological application) requires very high conversion levels. A common characteristic to all the chemical reactions involved in step polymerisation that should be emphasised is that they are most often equilibrated reactions. For instance, the polyesterification reaction is based on the esterification/hydrolysis equilibrium K COOH
+
OH
COO
+
H2O
4.8.4 Control of molecular mass The molecular mass in step polymerisation can be controlled by Controlling the duration of the reaction (kinetic control). Controlling the water concentration (thermodynamic equilibrium control). Controlling the stoichiometry by adding either difunctional monomers or a monofunctional reactant. Performing what is known as post-condensation. Most step polymerisations are exothermic and, consequently, the equilibrium constant K decreases with increasing temperature. Hence, one way to increase the molecular mass would be to decrease the polymerisation temperature, but kinetics prohibits using a too low temperature as it will lead to an excessively long residence time in the reactor and/or too high viscosities. Thus, in order to reach very high molecular
56
Jacques Devaux and Sophie Demoustier-Champagne
masses, a second step of reaction is sometimes performed under high vacuum for long periods of time in the solid state at a temperature where K is more favourable (post-condensation). Such a process finds industrial use for bottlegrade PET. It can be demonstrated that in step polymerisation, the polydispersity index H ¼ Mw/Mn ¼ 1+p. Consequently, the equilibrium polydispersity of step-grown polymers is often close to 2.
4.8.5 Livingness of the step polymers A consequence of the nature of step reactions is that macromolecules exhibit a ‘‘living’’ character, as their functional end groups are always able to react. As most of the reactions involved in step polymerisation are equilibrated, interchange reactions can occur. Interchange mechanisms can involve reactions between the terminal functional group of one polymer molecule with the internal repeating linkage of another macromolecule. Alcoholysis, acidolysis and aminolysis are other examples of reactions involved in the process. Interchange is also said to occur between internal links of two different macromolecules (through ester or amide interchange for instance). Most interchange reactions involve breaking and building of links of exactly the same nature. These reactions are thus most often athermal being only entropy driven. An example of such interchange equilibrium can be given for a polyester: O CHAIN#1
CHAIN#1
C O
+ CHAIN#2
O
CHAIN#2
C O O
CHAIN#1
CHAIN#2
C O
+ CHAIN#2
O
CHAIN#1
C O
The consequence of such interchanges are important and numerous Polymerisation — depolymerisation (hydrolysis for instance) equilibrium. Equilibrium molecular mass distribution in step polymers. Decrease of molecular masses upon end capping, due to re-equilibration.
Polymer Chemistry and Microstructure
57
Randomisation in miscible polymer blends (formation of random copolymers). Instability of block copolymers due to randomisation. Equilibrium formation-opening of cyclic oligomers.
4.8.6 Functionality — gelation — crosslinked macromolecules — networks The previous sub-sections of Section 4 were devoted to linear polymers made from monomers which were assumed to be bifunctional, or able to link to two other ones (Section 2.4). Vinyl (or similar) monomers used in chain polymerisation are bifunctional when they contain one vinyl (or similar) group per molecule. Monomers used in step polymerisation were so far assumed to contain two functional groups, being thus bifunctional. Crosslinked macromolecules can be formed from bifunctional monomers by first polymerising them, then by performing coupling reactions onto existing chains. The latter mechanism is often called vulcanisation.11 Several chemical routes can be followed to accomplish vulcanisation, depending on the functions available on polymer chains. In the section following monomers with more than two functional groups (fZ2) and polymers made thereof, defined as thermosets, will be discussed from a chemical viewpoint.
4.8.7 Crosslinking in chain polymerisation – polydienes Structures of monomers able to crosslink by chain mechanism can be rather different, but the majority of them are of the diene type, with two equivalent vinyl groups per monomer.12 A crosslinked system, including units of the diene type, can be considered as formed by linear chains (the initial chains) linked by randomly distributed bridging links. The bridging density r is defined as: n r¼ N0 where N0 is the total number of structural units and n the number of structural units belonging to a bridging link. It can be calculated [16] that the critical bridging density rc, at which a 3D network will appear is given by 1 1 rc ¼ yw yw 1 where yw is the mass average degree of polymerisation of initial chains.
11
Historically, the first crosslinking of macromolecules (natural rubber) was performed with sulfur thus given the name of Vulcanus, Roman god of volcanoes from where sulfur was extracted.
12
Conjugation phenomena, which can modify the reactivity of the second vinyl group, will not be considered here.
58
Jacques Devaux and Sophie Demoustier-Champagne
A bridging index can be defined as: X ny ry P d¼ ¼ ryn ny where ny is the number of initial chains of degree of polymerisation y and yn the number average degree of polymerisation of initial chains. The critical bridging index is y 1 d c ¼ rc y n ¼ n ¼ yw H The critical bridging index is thus the reciprocal of the heterogeneity factor H of the initial chains.
4.8.8 Crosslinking in step polymerisation-modified Carothers equation At the critical conversion value, the conversion p, the functionality f and the degree of polymerisation are linked. The simplest calculation model is due to Carothers. It is based on the hypothesis that the degree of polymerisation reaches infinity at the critical conversion, meaning that all the system is made of only one macromolecule. If N0 and N are the numbers of molecules at the beginning and during the reaction, fN0 is the total number of functional groups. Providing there is no intramolecular ring formation, the amount of functional groups disappearing during the reaction is 2(N0N). Therefore, p¼ which transforms as: p¼
2ð N 0 N Þ N0 f
2 N 2 1 1 1 ¼ f N0 f Xn
The latter equation is a modification of the Carothers equation and can be used to approximate the critical conversion value at the gelation. Indeed, when Xn goes to infinity the above equation leads to 2 p¼ f This critical value is, however, only an approximation leading often to an overestimation of the critical conversion value. The main reason to this failure is that gelation actually occurs, at least for some molecules, at a finite degree of polymerisation. Equations based on a statistical approach can provide better results in the estimation of gel point.
5. POLYMER DEGRADATION Similarly to polymer synthesis, there are essentially two main mechanisms of degradation of synthetic polymers involving main chain links and leading to
59
Polymer Chemistry and Microstructure
decrease of molecular mass: chain depolymerisation or unzipping and random (or statistical) degradation. Comparable distinctions can be made between the two mechanisms of chain and step polymerisations and degradations (see Table 8). Representative examples of such degradation mechanisms can be respectively found in radical depolymerisation of poly(methyl methacrylate) (PMMA), Figure 34, and in random thermolysis of poly(butylene terephthalate) (PBT), Figure 35. In random degradation molecular mass decreases early, while in chain degradation the molecular mass of the polymer remains almost constant. Characterisation methods for molecular mass are thus very sensitive methods to follow random degradation. In contrast, as monomer is produced in chain depolymerisation, weight loss measurement techniques are the best methods to follow this kind of degradation. (Chapters 10–12, in Section IV, of this book focus on the methods used in the molecular characterisation and analysis of polymer degradation and polymer degradation mechanisms.)
Table 8 Comparison between chain degardation (depolymerisation — unzipping) and step degradation (random degradation) Chain degradation
Step degradation
Needs initiation Monomer concentration increases steadily throughout the reaction High molecular masses remain all the along reaction The longer the reaction time, the higher the yield in monomer Reaction mixture contains: monomer high polymer E104 part of active species
Any bond can break at any time Almost no monomer produced except at the end of the reaction Molecular mass decreases rapidly
Depolymerisation (‘‘unzipping’’)
Random degradation
The longer the reaction time, the lower the molecular mass Distribution of all species can be calculated all along the reaction
CH3
CH3
CH3
CH3
CH3
O
O
O
O
O
C
O
C
C C C C H2 H2 CH3 CH3
C
O C H2
C CH3
O
C
O
C
C C C C H2 H2 CH3 CH3
CH3 C
O + H2 C
O
C CH3
Figure 34 Example of propagation step in chain depolymerisation mechanism (unzipping) of polymethylmethacrylate (PMMA).
60
Jacques Devaux and Sophie Demoustier-Champagne
O
O C
C O
T°
H
H2 CH C
O C H2
O
C
C
C O H2
C
H C
+ OH
O O
O C
O
O
H2 C
H2 C
O C C O H2
C
O O
Figure 35 Example of random degradation mechanism: thermolysis mechanism of poly(butylene terephthalate) (PBT).
It has also to be emphasised that polymers synthesized by chain polymerisation can undergo random degradation (as polypropylene for instance), while certain polymers synthesized by step polymerisation can depolymerise (e.g., polyamide 6). In the case of random degradation, the molecular mass drop due to chemical reaction with a contaminant (e.g., H2O, alcohol, acid, for a polyester) can easily be calculated. Consider the example of hydrolysis of a step polymer. There are two end groups on a linear polymer chain. Thus, their molar fraction is 2 X n0 where the subscript (0) indicates the beginning of the reaction. The molar fraction of new end groups due to hydrolysis is just the difference between the molar fractions before and after hydrolysis. As there are two end groups created by each water molecule, the molar fraction of new end groups is also twice the molar fraction of water. This can be written as: 2 2 2nH2 O ¼ N0 X n X n0 where nH2 O is the number of water moles and N0 the total number of structural units (moles) in the polymer. Multiplying both denominators by M0, which is the (mean) molecular mass of a structural unit, and dividing each member by 2 gives 1 1 nH2 O ¼ M n M n0 N 0 M 0 The denominator on the right side is the total mass of the polymer. Thus, multiplying the numerator and the denominator of the right-hand term by the molecular mass of water (18) leads to ½H2 Ow=w 1 1 ¼ 18 M n M n0 where ½H2 Ow=w holds for weight concentration of water.
Table 9 Summary of structure — property relationships of polymers Molecular structure
Double-bond (vinyl) monomers or bifunctional monomers
Plurifunctional monomers or bifunctional monomers+ crosslinking
Network ¼ giant macromolecule
Linear chains Branched or grafted chains
Homopolymers Copolymers
Glass transition
Order-crystallinity
WRoom temperature
Solubility
Effect of T1
Good
WoroRoom temperature
Disordered (amorphous) Amorphous thermoplastic (Partly) ordered ¼ (partly) Semi-crystalline crystalline thermoplastic
Softening to (viscous) liquid Softening+ melting
WRoom temperature
Usually disordered (amorphous)
Thermoset (crosslinked)
Insoluble (swells)
Non-meltable
Elastomer
Swellable but insoluble
Non-meltable
oRoom temperature
Type of material
Difficult
Notes: Within amorphous thermoplastics some are, due to asymmetry, non crystallisable while others are usually amorphous because they are too slow to crystallise during normal processing.
Polymer Chemistry and Microstructure
Monomers
61
62
Jacques Devaux and Sophie Demoustier-Champagne
This expression is particularly simple and useful for predicting the molecular weight after hydrolysis. It can be easily extrapolated for random degradations by reaction with any little molecule (‘‘contaminant’’) other than water.
6. SUMMARY As a summary to this chapter focusing on polymer chemistry and microstructure, major characteristics of polymers are reported in Table 9, classified under The type of monomers The (chemical) microstructure of the macromolecule The physico-chemical microstructural features leading to common classification J Glass transition J Order (crystallinity) Basic properties J Solubility J Thermal behaviour. As stated in the beginning of this chapter, few properties, depend directly and only on the chemistry. Table 9 summarises how chemistry influences (micro-) structure, which, in turn, governs properties. In this chapter, the ways synthesis’ processes influence the (chemical) microstructure were discussed. Processing methods, by providing the material its (physical) microstructure, also influence its properties. It is therefore the role of characterisation to gain insight into and control all the stages from chemical synthesis to the building of microstructure as well as the final polymer properties. The composition, uses and applications of commercial polymers are discussed in the next chapter (Chapter 3).
REFERENCES 1 2 3 4 5
6
7 8 9 10 11
J.P. Mercier, G. Zambelli and W. Kurz, Introduction to Materials Science, Elsevier, Paris, 2002. A.J. Kovacs, J. Polym. Sci., 30 (1958) 131. F.W. Billmeyer, Textbook of Polymer Science, Wiley, New York, 1962. M.B. Roller and J.D. Gillham, J. Coat. Technol., 50(636) (1978) 57. J. Carlier, R.L. Devaux and P.T. McGrail, Percentage of Rigid Chain Length, a new concept for predicting glass transition temperatures and melting points of poly(aryl ether ketones) and poly(aryl ether sulphones), Macromolecules, 25 (1992) 6646. V. Carlier, J. Devaux, R. Legras and D.J. Blundell, Extrapolation of short chain oligomers melting temperatures at infinite molecular weight, J. Poly. Sci., Part B: Poly. Phys., 36 (1998) 2563–2571. N. Grassie and G. Scott, Polymer Degradation and Stability, Cambridge University press, New York, 1985. B. Jambe, Ph.D. Thesis: Thermal Behavior of Poly(methyl n-alkyl silane)s (Prom. J. Devaux) Louvain-laNeuve (1997). P.J. Flory, Principles of Polymer Chemistry, Cornell, New York, 1953. G. Odian, Principles of Polymerization, Wiley, New York, 1981. J.R. Fried, Polymer Science and Technology, Prentice Hall PTR, USA, 1995.
Polymer Chemistry and Microstructure
63
K. Matyjaszewski, Prog. Polym. Sci., 30 (2005) 858. K. Matyjaszewski and P. Sigwalt, Polym. Int., 35 (1994) 1. G. L’Abbe and G. Smets, J. Polym. Sci., A-1, (5) (1967) 1359. J.P. Mercier and E. Mare´chal, Chimie des polyme`res in ‘‘Traite´ des mate´riaux vol 13’’, Presses polytechniques Universitaires Romandes, 1993, pp. 107–108. 16 J.P. Mercier and E. Mare´chal, Chimie des polyme`res in ‘‘Traite´ des mate´riaux vol 13’’, Presses polytechniques Universitaires Romandes, 1993, pp. 137–142.
12 13 14 15
This page intentionally left blank
CHAPT ER
3 Polymeric Materials: Composition, Uses and Applications J.P. Candlin
Contents
1. Introduction 2. Mode of Polymerisation 2.1 Oligomers, macromers and telechelic macromers 3. Polymer materials: Types and forms 3.1 Thermoplastics and thermosets 3.2 Amorphous and crystalline polymers 3.3 Elastomers (rubbers) and thermoplastic elastomers 3.4 Fibres 3.5 Flat films and sheets 3.6 Surface coatings and paints 3.7 Advanced materials 3.8 High performance polymers 4. Polymer Additives 4.1 Polymer-processing modifiers 4.2 Chemical property modifiers 4.3 Mechanical property modifiers 5. Summary Bibliography
65 66 68 68 68 70 74 77 79 81 84 84 87 88 98 112 117 118
1. INTRODUCTION Polymers play an integral role in modern society. Over 150 million tonnes are made annually. The scale of production varies enormously from a 200,000 tonnes per annum continuous operational plant for commodity polymers to a batch process producing a few kilograms of a specialised polymer (advanced material).
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00403-0
r 2008 Elsevier B.V. All rights reserved.
65
66
J.P. Candlin
Commodity polymers include: low density PE (LDPE) Polyethylene (PE)
linear low density PE (LLDPE) high density PE (HDPE)
Polypropylene (PP) Polystyrene (PS) Poly (vinyl chloride) (PVC)
Although some applications use these commodity polymers as structural components, their principal use is in packaging, e.g., films, bottles and containers. They are each made on a scale of over 10 million tonnes annually. Engineering polymers are often used as a replacement for wood and metals. Examples include polyamides (PA), often called nylons, polyesters (saturated and unsaturated), aromatic polycarbonates (PCs), polyoxymethylenes (POMs), polyacrylates, polyphenylene oxide (PPO), styrene copolymers, e.g., styrene/ acrylonitrile (SAN) and acrylonitrile/butadiene/styrene (ABS). Many of these polymers are produced as copolymers or used as blends and are each manufactured worldwide on the 1 million tonne scale. Advanced materials can be used in extreme conditions, e.g., high temperatures (W2001C), severe chemical environments (e.g., polytetrafluoroethylene (PTFE) with concentrated H2SO4). They are often used as a critical component in a workpiece and are frequently reinforced with glass, carbon or aramid (e.g., Kevlars) fibres. Organic polymers are sometimes referred to as plastics (although, this should be confined to thermoplastic polymers), macromolecules or resins, though the latter is often used to describe raw polymeric material awaiting fabrication. Many polymers are used in various forms that are not associated with normal plastic materials. These include paints and coatings, elastomers (rubbers), adhesives, sealants (caulks), surfactants and also their use in various industrial applications, e.g., ion-exchange resins, membranes.
2. MODE OF POLYMERISATION Polymers are formed via two general mechanisms, namely chain or step polymerisation, originally called addition and condensation, respectively, although some polymerisations can yield polymers by both routes (see Chapter 2). For example, ring opening of cyclic compounds (e.g., cyclic lactides and lactams, cyclic siloxanes) yield polymers either with added catalyst (chain) or by hydrolysis followed by condensation (step). Many polymers are made via vinyl polymerisation, e.g., PE, PP, PVC, poly(methyl methacrylate) (PMMA). It could be argued that the ethylenic double bond is a strained cyclic system. Another aspect is that the two reactants should yield a condensation product with the elimination of a small molecule, e.g., H2O. This is not essential. Thus in
Polymeric Materials: Composition, Uses and Applications
67
the formation of polyurethanes, the key step is the reaction: RNCO þ HOR0 ! RNHCOOR0 The general mechanism for chain polymerisation is (where M = monomer):
M
catalyst
M
M*
activated
rapid
M2*
nM
Mn*
termination rapid M n
whereas, for step polymerisation, the mechanism is: M þ M ! M2 M2 þ M ! M3 M2 þ M2 ! M4 ; etc: In general, Mn þ Mm ! MðnþmÞ The differences between chain growth and step growth polymerisations are shown in Table 1.
Table 1
Chain growth vs. step growth polymerisations
Chain mechanism
Catalyst or initiator required
Step mechanism
Polymerisation can proceed without catalyst Viscosity increases steadily throughout Viscosity increases rapidly at end of reaction polymerisation Monomer concentration decreases Monomer concentration decreases slowly during reaction rapidly before any high polymer formed Intermediates not usually isolatable Oligomers can be isolated at any stage (low concentrations of growing chains) MW independent of time MW increases with time MW generally decreases with MW independent of temperature increasing temperature (because termination reactions are enhanced) Rate of polymerisation is zero initially, Rate of polymerisation is a maximum at rises to a maximum as active centres the start and decreases continuously are formed from the initiator, and as the concentration of the functional then remains constant, before falling groups decreases off when the monomer is consumed Note: MW, molecular weight.
68
J.P. Candlin
2.1 Oligomers, macromers and telechelic macromers If the polymerisation is halted deliberately by adding a terminating or chain transfer agent, e.g., a monofunctional agent, or accidentally, e.g., adventitious introduction of poisons (e.g., air, water, solvents), then a polymer with a low molecular weight (MW) may result with a degree of polymerisation (DPn) of perhaps n = 4–20. These materials are called oligomers. With chain polymerisation this is carried out at the start of polymerisation and the chain transfer agent statistically terminates the polymerisation. The MW of the polymer depends on the ratio of chain transfer agent to monomer, for example, the MW of PE and PP prepared by the catalytic polymerisation of ethylene or propylene, respectively, can be controlled by the continuous addition of hydrogen to the feed. With step polymerisation, the progress of polymerisation is measured by viscosity. It can also be estimated from the amount of condensate removed. It can be arranged that these oligomers contain a reactive end group, e.g., hydroxyl, carboxyl, allowing subsequently further polymerisation with a different reactant monomer to take place. These reactive oligomers are called macromers. Finally, some polymerisations can be directed such that the final oligomer or polymer contains two or more reactive end groups capable of extended polymerisation with different monomers. These materials are named telechelic macromers or telechelic polymers.
3. POLYMER MATERIALS: TYPES AND FORMS 3.1 Thermoplastics and thermosets The terms thermoplastic and thermoset refer to the processability of a particular polymer and the properties of the finished article. Thermoplastic polymers are mostly a linear or branched linkage of monomers containing many thousands of repeat units. All the commodity polymers and most of the engineering polymers are thermoplastic. Thermoplastic polymers can be homopolymers or copolymers where two or more different monomers are used. With copolymers, different arrangements of the monomers are possible (see also Chapter 2). Random copolymer Alternating (or regular) copolymer Block copolymer
Graft copolymer
Arbitrary arrangement of monomers in the polymer chain Reciprocal array of repeat units (this occurs when two or more monomers react together to form a complex, which is then polymerised) Contains long sequences of one linkage joined onto another sequence with a different linkage. Di- and tri-blocks are possible Obtained by chemically reacting a second monomer/ polymer chain onto a pre-formed polymer
Polymeric Materials: Composition, Uses and Applications
69
The chemical nature of the repeat units determines the physical and mechanical properties of the polymer. Thermoplastics soften when heated and form a viscous melt; on cooling they solidify and become stiff. This process can be repeated. In the molten condition they can be shaped by injection moulding or extruded into tubes, films or fibres. The viscosity of the molten polymer varies with chemical linkage and MW of the polymer. The higher the MW, the higher the viscosity at a given temperature. As a general rule, the acceptable melt viscosity for extrusion, etc., is 1501C above Tg and 501C above Tm, where Tg and Tm are the glass transition and crystalline melt temperatures, respectively. Inter-chain attraction between the polymer chains determines the DPn necessary to give the polymer the required toughness, strength, etc. For polymers containing heteroatoms, e.g., polyesters, polyamides, DPn of 100–200 is adequate, whereas for polymers with little or no inter-chain attraction, e.g., PE and PP, then DPnW1,000 is recommended. Thermoset polymers (sometimes called network polymers) can be formed from either monomers or low MW macromers that have a functionality of three or more (only one of the reagents requires this), or a pre-formed polymer by extensive crosslinking (also called curing or vulcanisation; this latter term is only applied when sulfur is the vulcanising or crosslinking agent.) The crosslinks involve the formation of chemical bonds — covalent (e.g., carbon–carbon bonds) or ionic bonds. The act of crosslinking can either be an addition reaction (e.g., radical/radical) or a condensation reaction (e.g., alcohol/carboxyl). In the latter, the formation of volatile condensates is often not desirable because they may weaken the structure. Crosslinking reactions involve creating radicals along the polymer chain, which can couple to form a crosslink. A problem is that chain scission may occur. These radicals can be generated from added peroxide or, with more control, by high-energy radiation, e.g., X-rays (synchrotron), electron beams or g-rays (Co-60). For example, crosslinked PE is much tougher, more environmental stress cracking resistant and is often used for wire coating. When cold stretched and then heated it returns to its original shape, hence its use for shrink-wrap films or tubes. Depending on the strength of the crosslink, under most conditions, thermoset polymers do not melt, although with weak crosslinks, e.g., ionic, dipole-dipole, H-bonding, they are capable of being moulded. The normal procedure for the fabrication of thermosets is to add the reagents to a mould and leave to complete polymerisation. An alternative method is to stop the reaction before completion. Then, depending on the extent of polymerisation, the material can be injection or compression moulded, or, if the product at this stage is solid, it can be ground into a powder and compressed (moulding powders). The finished article is then cured by raising the temperature. As the reactants are often liquid, solvents are not used because they may get entrapped within the growing polymer matrix giving a poor surface finish. Conversely, the addition of volatile solvents at this stage is used to generate rigid foams. Polymer linkages that do not release condensates on being formed include polyurethanes (diisocyanate/polyalcohol) and epoxy (ring opening of the epoxy
70
Table 2
J.P. Candlin
Comparison of thermoplastic and thermoset polymers
Thermoplastic
Thermoset
Long-chain molecules, often without branching Soluble in some solvents
Cross-linked 3D structures
Crystalline and/or amorphous Variable MW; determined by solution techniques Can be flexible, soft or brittle Will flow under pressure Can be moulded or fabricated Many highly flammable Sometimes fail catastrophically at high temperatures Can be converted to thermoset by post-treatments
Can be swollen in solvents, but always insoluble Amorphous Very high MW; cannot be determined Rigid, brittle structure Structurally stable Only moulded articles (injection moulding possible with RIM) Many self-extinguishing Have good dimensional stability or fail slowly under load at elevated temperatures Impossible to remove crosslinks
group with polyamines). An advantage of liquid monomers is the ease by which they can be handled. Thus polyurethane articles can be made using reaction injection moulding (RIM). The two reactants are pumped into a mixing chamber then into a mould. Large articles, e.g., car bumpers, garage doors, can be made using this technique. Table 2 contrasts some of the properties of thermoplastic and thermoset polymers.
3.2 Amorphous and crystalline polymers No polymer is 100% crystalline, such as benzoic acid or NaCl, although PTFE can be over 90% crystalline. Conversely, polymers may be 100% amorphous; this occurs when the polymer chains cannot align themselves into a close, organised regular structure. About 50–100 uniform repeat units are necessary for crystallisation to take place. Amorphous regions in the bulk polymer are created when the polymer chain is capable of cis–trans configuration, rotational movement around a single bond or a crankshaft displacement involving several units in the polymer chain. Bulky substituents on the main polymer chain also lead to amorphous regions. Tacticity (see Chapter 2) of the polymer chain (i.e., extent of stereoregularity) also determines the possibility of crystallisation. Stereoregular, isotactic or syndiotactic polymers are often crystalline, whereas the corresponding atactic polymers are amorphous. Thus amorphous atactic PS has a softening temperature of 1001C and atactic PP is a viscous gum at room temperature, whereas syndiotactic PS and isotactic PP have crystalline melting
Polymeric Materials: Composition, Uses and Applications
71
temperatures (Tm) of 2701C and 1601C, respectively. These chain rotations, bulky substituents, etc., require space in which to move. This space is called free volume; it can be estimated by plotting volume (i.e., volume per unit mass) against temperature. Thermoset polymers are not crystalline because the multiple crosslinks do not allow the main chain polymer molecules any movement to form crystals. For all polymers (except those prepared by ‘‘living’’ growth mechanisms, see Chapter 2) because of molecular weight distribution (MWD), amorphous polymers do not have a sharp melting or softening point. Instead they have a broad temperature range of approximately 501C over which, on heating, the polymer changes from a brittle glassy solid to a pliable rubbery material. This change occurs at the glass transition temperature, Tg. The value of Tg depends on the chemical linkage of the polymer chain. Aromatic polymers with stiff, rigid para-linkages have high Tgs, e.g., poly(aryl ether sulfone) (PES) with a Tg of 2251C, whereas aliphatic carbon–carbon linkages, e.g., natural rubber, may have a Tg as low as –731C. In the rubbery, semi-molten state the polymer chains rotate, but on cooling the polymer behaves like a frozen liquid with a completely random structure. The chemical features that prohibit crystallinity are main chain flexibility (e.g., rotation), branching, random copolymers or low inter-polymer chain attraction. Normally, polymers are not miscible with each other and on cooling from the melt will separate into different phases. When miscibility is exhibited, e.g., poly(phenylene oxide) (PPO) and PS, crystallisation does not take place. Some of the properties and differences that amorphous and crystalline polymers exhibit are: (i)
(ii)
(iii)
(iv) (v)
Amorphous copolymers are brittle below Tg; elastomeric above Tg, although amorphous advanced materials with aromatic chains with high Tgs (e.g., PES) are tough at low temperatures. Amorphous polymers display small volume changes (compared with crystalline polymers) on cooling from the polymer melt to a solid, because in the melt the polymer chains are randomly oriented. Thus amorphous and crystalline polymers exhibit about 0.5% and 2.0% shrinkage, respectively. This shrinkage must be allowed for in precision or large articles. It can be compensated for by adding a small amount of foaming agent or filler during fabrication. Films made from amorphous polymers are more permeable to gases than crystalline polymers. More free volume is available for transport of the gases through the film. The amorphous phase is lower in density than the crystalline phase. Amorphous polymers are often transparent. Usually the crystalline phase has a different refractive index than the amorphous phase. This causes scattering and refraction giving the crystalline polymer a milky appearance. Unusually, the refractive index of crystalline isotactic poly(4-methyl pentene-1) is the same as the amorphous phase rendering
72
(vi)
(vii)
J.P. Candlin
the polymer transparent. This makes it particularly suitable for transparent sheets and laboratory ware (replacing glassware). Amorphous polymers will swell or dissolve in solvents. Crystalline polymers are more resistant to solvents; solvation has to overcome the attractive forces that exist within the covalent crystal lattice. If the affinity between the solvent and the polymer chain is low the crystal regions remain intact. Solvents can induce crystallisation. If the solvent is in contact with an amorphous polymer (but potentially crystallisable) diffusion of the solvent into the amorphous regions (plasticisation) lowers the Tg, allowing movement and reorganisation into crystalline lattices; the solvent itself is excluded from the lattice.
Although the chemical structure of the polymer chain may allow crystallisation, this may not be possible for the following reasons: (i)
(ii)
(iii) (iv)
Crystallisation from the polymer melt takes time and may require nucleation. If the cooling is rapid the organisation of the polymer chains into crystals may be too slow, resulting in an amorphous phase. To promote crystallinity the polymer must be re-heated to temperatures between Tg and Tm. This technique is called annealing. Another approach is stretching the polymer to promote crystallisation. This occurs in blow moulding of bottles and the biaxial stretching (drawing) of films. This increases the gas-barrier properties and because the induced crystallites are small (compared to the wavelength of visible light), the polymers are transparent. Amorphous cellulose tri-acetate sheets are used for overhead projector sheets for use in photocopying machines; they do not ‘‘curl up’’ or distort in the heated atmosphere. If poly(ethylene terephthalate) (PET) sheets are used, the biaxial stretching must be equal or it will curl up. Polymeric fibres increase in strength (increased tenacity) on being drawn. This orientation is performed between the Tg and Tm temperatures. (Methods for determining the extent of molecular orientation in polymers are discussed in Chapter 8.) Polymers vary in their rate of crystallisation depending on side chains, etc. Thus with PE crystallisation is almost instantaneous (less than 1 s), whereas nylon 6,6 and PVC (over 1 year to complete crystallisation) are sluggish. PET is slow to crystallise, but poly(butylene terephthalate) (PBT) is more rapid. Thus consideration of final application is critical, such as transparency and dimensional stability. Physical entanglement of the polymer chains restricts the translational movement necessary for alignment and crystallisation. Imperfections in the polymer chain. Insertions for chain polymer growth require ‘‘head-to-tail’’ for the correct stereoregularity (tacticity). A false ‘‘head-to-head’’ inclusion will disrupt the regular pattern. In a similar manner, atactic (non-stereoregular) insertions will produce amorphous polymers.
Polymeric Materials: Composition, Uses and Applications
73
As described above, crystallinity in polymers occurs when the polymer chain is regular and uniform and contains no defects (which can include external degradation, e.g., oxidation), and is critical for fibre applications. This arrangement is aided by inter-chain attraction. If a polymer does crystallise then the role of the amorphous phase becomes less important especially when considering mechanical strength and stiffness and the maximum service temperature. This is because the crystalline regions behave like temperaturesensitive crosslinks. They act like a thermoset when cold, but on heating (above Tm) are mouldable. This arises because emanating from each crystalline region are polymer chains (called tie molecules) that may be incorporated into separate different crystalline regions. The higher the MW of the polymer, the more this occurs and the polymer is much tougher. A significant aspect is the manner in which glass–fibre reinforcement increases the service temperature of semi-crystalline polymers; this is especially important in advanced materials. A value of the maximum service temperature can be obtained from the heat distortion temperature (HDT). This is measured by observing the temperature at which the polymer distorts under controlled stress. Normally with crystalline polymers this is between Tg and Tm of the polymer. With amorphous polymers this is below Tg. This can be seen by plotting modulus vs. temperature. An amorphous polymer has only one thermal transition (Tg), whereas a semi-crystalline polymer has two (Tg and Tm). When reinforced with glass fibres, the HDT of the crystalline polymer is raised to temperatures approaching Tm, whereas with the amorphous polymer the increase in HDT is small and remains below Tg. An illustration is shown in Figure 1 of the increase in HDT at a fixed modulus by the addition of glass fibres to amorphous and semicrystalline polymers. Amorphous
Semi-crystalline neat
glass-filled
glass-filled
modulus
modulus
neat
a fixed modulus
a fixed modulus
HDT neat increase temperature
HDT (glass-filled)
HDT neat
increase
HDT (glass-filled)
temperature
Figure 1 Illustration showing the increase in HDT at a fixed modulus by the addition of glass fibres to amorphous and semi-crystalline polymers.
74
J.P. Candlin
Table 3
Comparison of HDTs for amorphous and semi-crystalline polymers
Amorphous
Semi-crystalline
Heat distortion temperature (1C) Neat
PES
20% glass-fibre reinforced
B215 315 142 250 223 260
203 165 130 100 200 B100
PEEK PC Nylon 6,6 PEI PPS
Notes: PES, poly(aryl ether sulphone); PEEK, poly(aryl ether ether ketone); PC, polycarbonate; PEI, polyetherimide; PPS, poly(phenylene sulphide).
This improvement can be seen from the comparisons in Table 3. Some polymers, especially those with a rod-like, linear aromatic backbone, e.g., X X
X
X
X
X
O where X =
O
,
NH
,
C
O O
or
S
,
O
have a tendency to form crystals even whilst in the molten state or in solution. They are called liquid crystal polymers. They have very high melting points making them difficult to process, although careful introduction of flexible groups (e.g., –CH2–, meta-phenylene) does lower this to some extent. However, in the molten state or in solution with applied shear (e.g., extrusion processes) the polymer chains align together in the direction of flow and the viscosity decreases drastically allowing fabrication. In the solid state they are extremely anisotropic (uni-directional) and when combined with reinforcing fibres, e.g., carbon–carbon fibres, yield some of the highest service temperatures (approaching 4001C) known for polymers. Kevlars (produced from highly oriented poly(paraphenylene terephthalamide) is an example of a liquid crystal polymer.
3.3 Elastomers (rubbers) and thermoplastic elastomers Elastomers are defined as polymers that can be repeatedly stretched to B200% elastic elongation and will return to their original length when released. They can
Polymeric Materials: Composition, Uses and Applications
75
be either thermoplastic or thermoset, although with the latter the extent of crosslinking is low, typically 1–5%, i.e., 1–5 crosslinks per 100 backbone chain units. Most metals and ceramics have elastic elongation of less than 2%. Stretching in these materials involves the movement of atoms. In contrast, polymers can be easily elongated because the applied stress promotes linear formation of the polymer backbone. The MW of an elastomer must be high enough to promote chain entanglement thus preventing polymer chains from sliding past each other on applying stress. Because of the linear, organised arrangement of the polymer backbone on stretching, crystallisation may occur. This also helps to increase the strength on stretching (tie molecules). The requirements for an elastomer are: (i) (ii)
(iii) (iv) (v)
High MW to promote chain entanglement. Amorphous, although crystallinity when stretched is often advantageous. This promotes tie molecules and strengthens the elastomer at maximum extensions. The Tm of the crystalline region must be near or below the working temperature such that the crystallites can melt when the stress is removed, e.g., natural rubber, Tg –731C; Tm 251C. Flexible backbone, allowing chain rotation, etc. Low Tg allowing chain movement at ambient temperatures. Thus for room temperature usage this requires a Tg of less than –501C. Low creep value (this is the flow of polymers when stress is applied over long time periods). This is achieved by low level crosslinking (less than 5%).
In some cases the modulus and strength are so low that fillers are often added for stiffness. Carbon black, as a filler, is used extensively in car tyres, and it is thought that the surface bonding with the rubber occurs, thus providing stiffness. Finely divided silica, which has been surface treated with organometallic silicon and titanium compounds, is also used. Covalent crosslinks, once formed, are non-reversible. Once made, they cannot be broken. This limits the processing options to low shear techniques, such as calendaring in which a mangle arrangement with three parallel rollers presses the polymer into sheets, or to adding the crosslinking agent at the last stage. Heat reversible crosslinks, however, allow the elastomer to be treated similarly to a thermoplastic, capable of being extruded or injection moulded at a high temperature whilst behaving like an elastomer at low temperatures. There are various ways of forming covalent crosslinking: (i)
(ii)
Olefinic polymerisation, e.g., ethylene/propylene to which is added a diolefin (diene), where the diene is 1,4-hexadiene or 4-ethylidene norborn-2ene. The resulting polymer is usually called EPDM (ethylene propylene diene monomer). Vulcanisation of unsaturated rubbers, e.g., poly(1,4-butadiene), polyisoprene, random styrene/butadiene rubber (SBR) with sulfur. The sulfur attacks the allylic C–H group to form inter-chain –S–S– linkages.
76
(iii)
(iv)
(v)
J.P. Candlin
Peroxide cure of saturated olefinic polymers, e.g., random, non-crystalline ethylene/propylene copolymers (prepared by Ziegler catalysts). The peroxide generates carbon radicals, which couple together forming inter-chain covalent bonds. Dimethyl silicone polymers have no strength. Reaction with peroxide gives random radicals, which link together and stops the silicone chains from sliding past each other on being stretched. Neoprenes is a polymer formed from chloroprene (2-chlorobutadiene). On heating with zinc oxide the neoprene polymer rearranges to give a pendant labile allylic chloride group (–CH = CH–CH2Cl). Further reaction with zinc oxide yields zinc chloride and a stable ether link between the two polymer chains. The copolymer of vinylidene difluoride and per-fluoropropylene (Vitons) on heating releases HF and gives an unsaturated fluoropolymer. Reaction with a diamine introduces crosslinks. This fluoroelastomer has a very high service temperature of over 2001C.
The linkage between two chains can also be ionic. Thus the copolymer between ethylene and methacrylic acid (MA) (up to 15% MA), made by free radical polymerisation, yields a polymer with pendant carboxyl groups. Neutralisation with zinc ions gives a crosslinked, thermo-reversible polymer (Surlyns). The resulting polymer (ionomer) has limited properties, although it is the favoured material for the outer covering of golf balls. Crosslinks prevent the flexible polymer chains from sliding past each other; crystallinity could play a similar role as long as the percentage of crystallinity is small. (Polyethylene has the potential to be an elastomer, but its crystallinity is too high — greater than 60% and therefore behaves like a thermoplastic). A big advantage, however, would be that the elastomer would be thermo-processible. Another approach would be to design a copolymer prepared by block polymerisation, which has one segment that can form crystals. If that is not achievable, one could have an amorphous segment with a high Tg (higher than the service temperature) to form a glassy domain. The other segment would consist of a flexible chain with a low Tg. These segments are often referred to as hard and soft segments, respectively. Following that approach, many thermoplastic elastomers (TPEs) have been synthesised using this principle, e.g., see Table 4. Careful control of the chain length of each block has to be made. An interesting observation arose with the thermoplastic elastomer styrene/ butadiene (S/B) tri-block copolymer (Kratons). These are made by anionic Table 4
Some thermoplastic elastomers
Hard segment
Soft segment
Poly(butylene terephthalate) Aromatic urethane Aromatic polyimides Aromatic polyesters or carbonates
Poly-1,4-butane diol (Hytrels) Poly-1,4-butane diol (spandex) Perfluoropropylene oxide Polydimethylsiloxanes
Polymeric Materials: Composition, Uses and Applications
77
polymerisation (living polymerisation). Thus either polystyrene/polybutadiene/ polystyrene (SBS) or polybutadiene/polystyrene/polybutadiene (BSB) tri-blocks can be made. The former has much better elastomeric properties than the latter. This is because the polystyrene end segments have the freedom to move and form a glassy domain (PS Tg, 1001C) together with tie molecules, whereas with polystyrene end-capped with polybutadiene the polystyrene segment is restricted in its movement. The polybutadiene segments have a low Tg of –1001C and therefore will not form a glassy rigid structure at ambient temperatures necessary for added strength on stretching. Polymers with blocks containing different tactcities can be produced, e.g., atactic PP (amorphous)/isotactic PP (semi-crystalline) can be made using metallocene catalysts. They behave in a manner similar to SBS thermoplastic elastomers.
3.4 Fibres Synthetic fibres are thermoplastic materials and are fabricated by either melt processing or from a solution of the polymer in a solvent. Both processes use a spinneret. The main structural requirement is that the polymer must have a linear backbone (with little branching). On drawing or stretching the polymer chains align promoting crystallinity giving the fibre added strength. In principle, there are many polymers suitable for fibres, but for apparel (clothes) and domestic (carpets) use only four types dominate: polyester, polyamide, polyacrylonitrile (often as a copolymer with vinyl chloride) and polypropylene. For melt spinning, it is necessary that the melting temperature of the polymer is not too high as to cause decomposition, and that the melt viscosity is low since it passes through the spinneret holes (diameter approximately 120 mm). Each spinneret plate contains hundreds of these holes. Conversely, the Tg of the fibre must be low enough to permit ironing, but the Tm must be sufficiently high to prevent melting during ironing. For melt fabrication the temperature of the melt is approximately 501C higher than Tm (although with polypropylene this is 1001C higher). Melt spinning is used to make polyester, polyamides (nylon 6 and 6,6) and polyolefin fibres. Wet or solution spinning is used for natural fibres (cellulose derivatives) and some synthetic fibres. This can be achieved by passing a concentrated solution of the dissolved polymer through the spinneret into a coagulating bath, e.g. polyacrylonitrile/dimethyl formamide (DMF) and cellulose/N-methyl morpholine N-oxide (NMMO) (Tencels) into water. With wet spinning, the solvent is evaporated by heat, e.g., aramid/concentrated H2SO4 into water and polyurethane elastomeric fibres/DMF followed by coagulation with water. The main structural/property requirements for fibre formation are: (i)
The polymer chain must be uniform with no defects in chemical composition or stereochemical arrangement. This condition is stricter than for other applications.
78
(ii) (iii) (iv)
(v)
(vi)
J.P. Candlin
Sufficient molecular weight to exhibit chain entanglement, promoting fibre strength during drawing. Linearity of backbone, with little or no branching. The inter-molecular forces between the polymer chains enhance structural cohesion giving the polymer strength during spinning and drawing. This is achieved by incorporating heteroatoms (e.g., N, O) in the polymer backbone thus encouraging H-bonding, dipole–dipole or aromatic– aromatic p-electron attraction. Crystallisation during the drawing process caused by aligning the polymer chains. These small crystallites encompass polymer tie molecules giving the fibre added strength. With amorphous copolymer fibres, e.g., acrylonitrile/vinyl chloride (acrylic fibres), crystallisation does not occur, but the act of drawing optimises the strong dipole–dipole forces and increases the strength of the fibre. Orientation of the crystallites parallel to the fibre axis gives the fibre added strength (tenacity), and because of the rapid rate of drawing, the size of the crystallites is small when compared to the diameter of the fibre.
In principle stretching or drawing of fibres should be undertaken between Tg and Tm, thus minimising brittle fracture. Thus polyester (e.g., PET) and polyacrylonitrile (PAN) fibres are heated during drawing. With wet spinning, the presence of the solvent acts as a plasticising agent and thus decreases Tg, e.g., nylon drawn in an atmosphere of high water humidity. The extent of draw (draw ratio) affects the tenacity of the fibre. Thus for fibres for apparel, i.e., soft, flexible fibres, a low draw is used (100% elongation), whereas for fibres with a high strength, e.g., ropes, tyres, requires a high draw (400%). Originally, this led to irreversibility in finished garment, e.g., kneed stockings. This has been overcome by the steam treatment of the drawn fibre (PET) before weaving. Many other properties have to be considered, especially for apparel fibres, e.g., moisture absorption, ability to dye, drape, texture, weaving characteristics, etc. Many of the properties are influenced by the cross-section profile of the fibre. Thus cotton and some rayons (an artificial synthetic fibre derived from cellulose) are a hollow round fibre; silk has a triangular shape giving it a fine lustre and drape. Using co-extrusion it is possible to make fibres with a nylon 6,6 inner core (Tm 2641C) and a nylon 6 outer shell (Tm 2151C). By applying pressure and heat between these two temperatures to bundles of these two fibres, a non-woven mat can be made. The elastomeric fibre, elastane or spandex (the anagram of ‘‘expands’’) is a hard/soft segmented block copolymer. The soft segment (with a low Tg) can be a polyglycol (e.g., polyethylene glycol or polybutylene glycol) or an aliphatic polyester glycol and has a DPn of approximately 25. This constitutes up to 80% of the polymer weight. The hard segment is a polyurethane or polymer prepared from aromatic di-isocyanates. Strong inter-molecular forces (e.g., H-bonding, crystallinity) and phase separation of the two segments renders the copolymer elastomeric, which allows 600% extensions with full recovery (similar to natural
Polymeric Materials: Composition, Uses and Applications
79
rubber, but without the inherent oxidative instability and attack by ozone). The polymer can be processed into fibres by either melt spinning or from solution (using DMF as the solvent). The latter method is used when polyurea is the hard segment, since they decompose on melting. The main application of spandex (e.g., Lycras) is for stretched apparel clothing. It is used to make yarns when combined with other natural and synthetic fibres. Although the main usage of fibres is for apparel, many applications are unique to synthetic fibres. Examples include (i)
(ii)
(iii)
(iv)
High modulus polyethylene fibres are made by dissolving ultra high MW polyethylene (W106) in decalin or paraffin oil (2% solution) at 120–1701C and drawing through a hexane bath. Extended chain polyethylene fibres (e.g., Dyneenas) are used as ballistic-resistant yarns, and have strengths comparable to aramid fibres, but they do not possess high temperature resistance. Melt-spun HDPE (fluff-like, similar to candy floss, made by flash-spinning technology) is loaded onto a moving bed to give a random mat that is consolidated by heat and pressure (Tyveks). These mats allow moisture but not liquid water to pass through. Their main application is in construction, but it also has many other uses, e.g., envelopes, protective clothing. Biodegradable polyester copolymers of lactic/glycolic acids are used as sutures in medical operations. They degrade and dissolve harmlessly in the body. Hollow amorphous aromatic polysulfone fibres, presenting a high surface area, are used as membranes for separating liquids and gases.
3.5 Flat films and sheets Films and sheets are defined as planar flat materials that are self-supporting and flexible. Generally films have a thickness of less than 250 mm, above this thickness they are referred to as sheets. They may consist of one or more layers, usually of different compositions. Films or sheets can be used alone or co-extruded with paper, foil or fabrics. The main application for films is for flexible packaging material, but because of their versatility they can be modified to fulfil many uses, such as electrical insulators, a base for printing and writing, permeable membranes, and many more. Sheet materials tend to be greater than 1 mm thick and are often used as replacements for glass, wood and metal. Examples include window glazing and outdoor signs. Sheets can be transformed into shapes by vacuum moulding (thermoforming).
3.5.1 Manufacturing of films and sheets The techniques following are used for the manufacture of films and sheets: (i)
Mould casting between planar parallel moulds. The polymer or macromer is injected into the mould as a viscous liquid together with a catalyst.
80
(ii)
(iii)
J.P. Candlin
Another approach is the use of RIM using reactant monomers and a catalyst. The viscosity must be low enough to allow for flow of the reactants. This sometimes precludes polymer melts with high viscosity. Solvents are not used because volatilisation may cause bubbles. Continuous casting. In contrast to mould casting, this can use solutions of polymer. The mixture is fed onto a horizontal moving belt and the solvent is removed by evaporation. This technique has the advantages over extrusion process: a. No heat stabiliser is used, thus the sheet has greater clarity without distortion. b. Uniformity of thickness. c. Very wide sheets (over 2 m) can be processed. This is difficult with extruded sheets because of the intricate design of the clothes-hanger die used to prevent warpage caused by polymer chain orientation. Continuous casting however, using molten polymer, has been used providing the viscosity is low enough. Many polymers have been processed by casting, e.g., acrylics, polystyrene, polyamide (nylon 6), phenolics, PVC/plasticiser. Many of these are used in a pre-polymer form, which polymerise on the casting belt, or the polymerisation can be completed later by application of heat. Extrusion processes. Two techniques are used to make very thin films of less than 10 mm thickness. a. Stenter or tenter process. Extruders continuously force the molten polymer through a clothes-hanger die, which is then cooled. The sheet (approximately 500 mm thick) is re-heated (between the Tg and Tm of the polymer) and drawn by pinch or nip rollers, which stretches the sheet in the forward (machine) direction. Simultaneously, clamps (tenterhooks) stretch the sheet sideways. The finished film is then collected on a cooled rotating drum. The resulting film is between 2 and 5 times the original length and width with a corresponding reduction in thickness. This stretching, similar to the drawing of fibres, which promotes orientation and crystallite formation, is called biaxial orientation. It gives the film added strength and gas-barrier properties. In some processes, monoaxial (uniaxial) drawing is employed, e.g., polypropylene, which is then slit into thin strips and fabricated into heavy duty sacks, carpet backing, etc. The stenter process is used to make biaxial oriented poly(vinylidene dichloride) (‘‘cling’’ film), polyester, polyamide and polypropylene films. b. Blown films. The molten polymer is passed through a tubular die, the centre of which contains an air-inlet. Increasing the pressure of the air forces the tube to expand like a bubble, the top of which is clamped together by rotating nip rollers. Thus a continuous thin film, tubular roll is fabricated. The nip rollers are set to stretch the film in the forward direction, whilst the bubble expands the film in the sideways direction. Thus biaxial stretching is achieved. Bi-layers and multilayer films with different polymers are made by having two or
Polymeric Materials: Composition, Uses and Applications
(iv)
81
more concentric dies. This can be used to optimise properties, e.g., one layer has good gas-barrier properties, and the other layer has good tear strength. Biaxial polypropylene (Tm 1651C) is difficult to heat seal (large shrinkage occurs on melting), but co-extrusion with polyethylene (Tm 1151C) allows the bi-layer to be sealed below the melting temperature of polypropylene. Films of polyolefins, polyamides and poly(vinylidene dichloride) are made using this technique. As most of the films are used for flexible packaging, further down-stream surface treatments are usually applied to improve performance. For example, aqueous polymer emulsions, e.g., poly(vinylidene dichloride), or delaminated clay particles improve the barrier properties as will metallising with aluminium vapour. Corona discharge, causing slight surface oxidation, improves printability. Calendering. This method is used to process heat-sensitive polymers, such as plasticised PVC, and also to blend polymer mixtures or add additives. The polymers are fed and heated on hot rolls and squeezed between two or more parallel nip rollers into the form of a thin film or sheet. The process can be easily modified to incorporate backing material, e.g., metal foil, paper and textiles. Only polymers with a high viscosity can be processed by this method.
3.6 Surface coatings and paints Several million tonnes of polymers are incorporated annually into coatings and paints. Coatings are applied for several reasons apart from being aesthetically pleasing, for example: (i) (ii) (iii) (iv)
They form a protective layer, which inhibits corrosion (with metals) and bacterial attack (with wood). They fill and smooth imperfections. They provide a durable decorative and alternative surface finish, e.g., matt or gloss. They are resistant to household cleaning products such as bleach and solvents.
The first paints were based upon linseed oil (obtained from flax). This is an unsaturated long-chain triglyceride, which, with metal activators, crosslinks via radical pathways to form a continuous film on the substrate. Modern paints use synthetic polymers together with either a solvent or suspending medium (e.g., water), which evaporates leaving the deposited film. Exceptions are powder coatings, which require heat for completion. The main requirements for a coating are that it is easy to apply (i.e., low viscosity) and dries to a non-tacky finish within a reasonable time. Originally, this equated to the solution and evaporation of the solvent. However, because of environmental concerns, formulations have tended to shift the concentration of solvents from 80% to less than 20% (known as high solids coatings). Many industrial processes use polymer powders (of approximately 40 mm diameter),
82
J.P. Candlin
which are attracted electrostatically to the substrate before being cured by melting or electron beam treatment.
3.6.1 Polymers, resins and binders used in paints These are the most important components of paint. Coatings can be either clear or opaque (containing pigments) and either solvent- or water-based. With solventbased paints, after application, most of the solvent is lost through evaporation. These solvent-based coatings are mostly alkyds (name derived from alkyl/acid) or modified alkyd resins. Normally they contain 30% polymer solids; higher solids content is limited by the increasing viscosity of the system. Alkyds are crosslinked polyesters made from 3- or 4-functional alcohols, e.g., glycerol or pentaerythritol, and a 2-functional carboxylic acid, e.g., phthalic acids and maleic acid. Also added are long-chain unsaturated oils, e.g., vegetable oils. The oligomerised product is dissolved in mineral oil or toluene. On application to a surface, the solvent evaporates and the remaining mixture undergoes catalytic (cobalt naphthenate catalyst) autooxidative crosslinking to form a continuous coating. Modified alkyds include the addition of silicones, phenol-formaldehyde, urethanes, styrene, epoxies and acrylics, which are grafted onto the alkyd backbone, e.g., urethane and epoxy groups are grafted using excess hydroxyl groups in the alkyd formed by reaction with isocyanate and oxirane (epoxy) groups, respectively. Styrene and acrylics modifications are obtained by radical polymerisation and phenol-formaldehyde by reaction of methylol groups with hydroxyl groups. Urethane alkyds are the most important. If the coating is for both outdoor and indoor use then aliphatic di-isocyanates are used. Aromatic di-isocyanates yellow and may crack when used for outside applications. Latex or emulsion polymers are prepared by emulsification of monomers in water by adding a surfactant. A water-soluble initiator is added, e.g., persulfate or hydrogen peroxide (with a metallic ion as catalyst), that polymerises the monomer yielding polymer particles, which have diameters of about 0.1 mm. The higher the concentration of surfactant added, the smaller the polymer particles. In suspension polymerisation, so-called because of the addition of watersoluble suspending agents, e.g., poly(vinyl acetate) (PVA), starch or surfactant, a monomer-soluble catalyst is added (e.g., organic peroxide) resulting in larger porous particles (approximately 500 mm) that readily absorb plasticisers. This is sometimes called bead or pearl polymerisation because of the smooth spherical shape of the polymer particles. Several different monomers may be used together to yield the desired properties. High molecular weight polymers, giving increased polymer toughness, can be prepared without the attendant increase in viscosity or without the necessity for crosslinking. With smaller polymer particle sizes, more pigment may be added to give greater opacity. However, this requires more surfactant resulting in less durability. A high polymer content (W65%) in the emulsion can be obtained. A small amount (o5%) of high boiling solvent is added, e.g., glycols, glycol ethers or alkyl-aromatic compounds depending on the polymer. These solvents plasticise the polymer and promote coalescence of the polymer particles after evaporation of the aqueous phase.
Polymeric Materials: Composition, Uses and Applications
83
The greatest use of latex paints for indoor applications is based upon vinyl acetate, which constitutes 85% of the total polymer usage, the remainder being acrylates (e.g., n-butyl acrylate). For outdoors or bathroom usage, acrylates are the major components. For various applications, e.g., wood paints, styrene copolymerised with acrylates are used. However, yellowing of the styrene units occurs. The mode of polymerisation and crosslinking for coatings is very similar to that of bulk polymers. An important requirement is that premature polymerisation should not take place before application. In the presence of activators, e.g., cobalt naphthenate, many paints on exposure to air polymerise by radical oxidation resulting in crosslinked structures. Stepwise growth polymerisation, e.g., urethanes, is promoted by heat; therefore storage at high temperatures (W501C) should be avoided. A growth area is UV or electron beam curing. This can be via radical polymerisation, e.g., a benzoin derivative, O
OR
C
CHPh
O
OR
C
CHPh
UV Ph
Ph
or cationic polymerisation (with epoxy resins) using aromatic (Ar) onium salts, e.g., sulfonium salts, Ar3S BF4
UV
Ar + Ar2S
BF4 H (from solvent)
Ar2SH BF4
Ar2S + HBF4
The strong acid, HBF4, acts as the catalyst. Cationic polymerisation is used for coatings and printing inks. Several conditions are necessary for satisfactory surface coatings, e.g., nondrip applications. There is a balance between the ease of use and sagging of the paint during and after administration. Thixotropic additives, e.g., organomontmorillonite clays are added. These form 3-dimensional networks, which are easily broken down by shear. Various finishes can be achieved — gloss, satin (or egg-shell) or matt. This is accomplished by the addition of particles of size 1–5 mm of, for example, silica, china clay or the white pigment, TiO2. The degree of mattness depends on various factors, such as particle size, surface treatment of the particles, rate of film formation, and the polymer composition, e.g., urethane/acrylate compared with epoxy/acrylate. The former requires smaller particles; larger particles cannot be used as they create a rough surface.
84
J.P. Candlin
One of the largest uses of paints is in the automotive industry and the coatings of metals for decorative and anti-corrosion purposes. This is achieved using electrophoresis. The first pre-treatment provides corrosion resistance by phosphating using a solution of zinc or iron phosphate. Next a water-insoluble polymer is solubilised by converting it into a soluble salt through neutralisation. Thus alkyd resins containing free carboxyl groups (polymer–COOH) are treated with KOH to give the water-soluble salt (polymer–COO~K). In a similar manner, treatment of an epoxy/amino resin with a carboxylic acid, e.g., acetic acid, converts the polymer into a water-soluble quaternary ammonium salt, polymer NR2 þ CH3 COOH ! polymer NR2 HY OOCCH3 Electrophoresis of water solutions of these salts and using steel as either the anode or the cathode, respectively, liberates the water-insoluble polymer coating through the reaction: Anode deposition; polymer2COOY K þ
H
ðfrom anodeÞ
! polymer2COOH ðinsolubleÞ
Cathode deposition; polymer2NR2 HY OOCCH3 þ
OHY
ðfrom cathodeÞ
! polymer2NR2 ðinsolubleÞ
For various reasons, cathodic deposition is the most favoured. The main advantages are that complete surface coverage is obtained and also, because the coating-insoluble polymer is an insulator (inhibiting deposition), a uniform coating is achieved.
3.7 Advanced materials These are materials that can be used under extreme conditions such as high temperatures, greater than 2001C, or severe chemical environments or permit a unique application, e.g., highly branched polyethylene oxide does not crystallise; it serves as an electrolyte for lithium ion batteries, with no crystalline regions inhibiting the transport of ions. Many also exhibit properties not normally commonly associated with polymers, e.g., conducting electricity or semiconducting or displaying piezoelectricity. Some can also show (so-called) ‘‘smart’’ behaviour, whereby they can counteract any outside influence or stress.
3.8 High performance polymers These are normally prepared by a step growth mechanism. They can be thermoplastic or thermoset and are often used in composites. Composites are materials that contain two or more phases, one of which acts as a reinforcement
Polymeric Materials: Composition, Uses and Applications
85
for the other, e.g., a binder polymer is combined with fibres made, for example, from glass, carbon, boron or aramid, to generate a tough, stiff, yet mouldable material. Thermosetting polymers are brittle because of the crosslinking that occurs during polymerisation. However, the precursors are liquid and in this state can easily wet and impregnate long fibres masses, mats and cloth. High performance thermoplastic polymers are tough but can deform under pressure and heat. They are often processed via extrusion or injection moulding with short fibres (1–5 mm). Care must be taken to promote random orientation thereby giving isotropic strength (similar to polymer crystallisation of drawn fibres and films). New techniques have been developed, e.g., pultrusion, whereby a continuous web of fibres is passed through a bath of molten polymer, which can be a thermoplastic, e.g., PEEK, or a semi-cured thermoset, e.g., epoxy or unsaturated polyester. The resulting coated fibre is called a prepreg and can be used to wrap around a mould and finally cured at a higher temperature or by radiation. High performance plastics have high temperature stability. They have a very high limiting oxygen index (LOI, sometimes called critical oxygen index (COI)), which is increased when reinforced with glass fibres. Because of the high aromatic content they tend to char on combustion and do not release flammable volatiles. Furthermore, radical decomposition is inhibited by the delocalised aromatic system, which stabilises the propagating radical intermediates. Polymers containing heterocyclic or di-substituted aromatic groups, often called ladder polymers, have outstanding thermal stability (over 5001C for short periods). The ladder structure allows individual bonds to fracture without breaking the chain. They have high strength to weight ratio (comparable with metals), high modulus and are tough and not brittle at ambient temperatures even when they are amorphous. Examples of high temperature polymers are: Poly(ether imides), O
O
C
C
CH3 C
N
N C
C
O
CH3
O
O
n
Ultem® O
O
C
C O
N
N C
C
O
O
n Kapton® Vespel®
86
J.P. Candlin
Poly(aryl ether ketones),
O
O
C O
O
C O
n Victrex®
PEK
n
PEEK
Poly(aryl ether sulfones), O O
S n
O PES
O S
CH3 C
O
O
CH3
O n
®
Udel
Aromatic polyamides (aramids),
HN
NH.CO
NH.CO
CO n
HN
CO n
Kevlar®
Nomex®
Aromatic polyesters, O O O
C
C O n
Vectran®
Kevlars has the highest tensile strength and is often used as a reinforcing fibre in composites with, e.g., epoxy, PEEK. The thermotropic liquid crystal polymer Vectrans is made by melt polymerisation of p-acetoxybenzoic acid and 6-acetoxy-2-naphthoic acid, (the corresponding hydroxy acids decompose on melting). Because of its liquid crystal properties the polymer can be spun into fibres from the melt. Kevlars is spun from a solution in concentrated sulfuric acid, and can be melt drawn to give a high modulus (stiff) polymer. Vectrans
Polymeric Materials: Composition, Uses and Applications
87
fibres have high tenacities (strength), comparable with Kevlars and has service temperatures up to 3001C. It has many applications, e.g., cut-resistant gloves and clothing, catheters, reinforcement of ropes and yarns. Although Nomexs fibres have tensile strength properties similar to apparel fibres, they also have very high service temperatures (up to 3701C) and high flame resistance. Nomexs is self-extinguishing when removed from a flame because of the formation of char resulting in low smoke generation. It is extensively used in protective clothing and materials, e.g., by fire-fighters, for aircraft fabric, and by racing-car drivers. Nomexs is prepared from the corresponding di-acid chloride/diamine and wet spun from a solution of dimethylacetamide/5% lithium chloride.
4. POLYMER ADDITIVES This is an extremely important area. Commercial polymers are very rarely prepared or used without additives and they often contain a combination of additives. These improve processability of the polymer, its durability, service life under adverse conditions (e.g., temperature, UV light and various chemical environments), strength (e.g., using reinforcing fillers), appearance (colorants), etc. A recent use of additives is to facilitate reprocessing or recycling or, alternatively, to promote decomposition (which is often difficult because the stability is inherent in the polymer’s chemical structure). (The analysis of additives in polymers is the subject of Chapter 14.) Polymer additives may be classified into five groups (although some additives can serve more than one purpose, e.g., plasticisers, carbon black): (i) (ii)
(iii)
(iv)
(v)
Additives that facilitate or control polymer processing, e.g., lubricants, mould-release agents, blowing agents and plasticisers. Chemical property modifiers. These enhance stabilisation against degradation and aging during processing or in use. Degradation usually involves chain cleavage and is usually caused by energy (e.g., shear forces during processing, heat, UV light) or by chemical attack (e.g., oxidation, hydrolysis). Thus many polymers require anti-oxidants, light or heat stabilisers, etc. The promotion of new desirable properties for the polymer such as improved mechanical or electrical properties or dimensional stability. Fillers enhance many of these properties. Aesthetic property enhancers. These additives (e.g., colorants) will improve the polymer’s appearance and make it suitable for various applications. Degradation additives. These additives are usually added for environmental purposes in order to promote the decomposition of polymers after use.
The total world demand for additives is ca. 2 million tonnes per annum (excluding fillers and colorants — with fillers this becomes 20 million tonnes per
88
J.P. Candlin
annum). Their concentration can vary from a few ppm to W50% for flame retardants and fillers. The average is ca. 20 wt% of all polymers consumed.
Fillers Plasticisers Reinforcing agents Flame retardants Colorants
Consumption (%) (wt additive/wt polymer) 58 16 (almost solely with PVC) 10 6 5
The additives can be added during the polymerisation (either in the form of a reactive monomer or as an inert material — advantages include better dispersion and increased retention), but they are usually added immediately postpolymerisation of the polymer and extruded with the polymer. Often a concentrated mix with the plastic (master-batch) is prepared by the plastic manufacturer and this can be sold to the fabricators to be added during subsequent processing. When using additives the following precautions should be taken: (i)
(ii)
(iii)
The additives should not exude to the surface of the plastic article (there are some exceptions when surface modifications are required) or lost by volatilisation or decomposition during processing. Defining the end-use of the plastic. Strict controls are enforced when plastics have contact during food preparation or packaging. This is a difficult area because often the plastic manufacturer may not be aware of the final application. The fabricator must therefore ensure that the plastic article containing the additive is in compliance with the regulatory laws of the country where the article is sold. Another difficulty is the toxicity of the additive, e.g., carcinogenic or poisonous (e.g., lead or cadmium pigments) and asbestos fillers. Many additives (especially for plastics with food contact use) require approval from regulatory authorities. This costs money and time and therefore the general pattern is to use proven additives whenever possible. Interaction between the additives. Conversely some additives may serve two purposes (e.g., UV and heat stabilisation; lubricants cannot only aid processing but can also promote mould release).
It is difficult to generalise additives in that they may work with a particular polymer but not with others because of chemical compatibility, processing temperature and conditions.
4.1 Polymer-processing modifiers 4.1.1 Heat stabilisers Some polymers degrade readily when heated to the processing temperature by bond scission. In contrast, if the polymer has a completely aromatic structure (e.g., PES, PEEK) the thermal stability is high (greater than 4001C for short
Polymeric Materials: Composition, Uses and Applications
89
periods). Thus, when PVC is heated above 1001C an autocatalytic decomposition occurs and at 1801C it becomes dark brown within a few minutes. Thermal degradation of polymers can occur by three mechanisms (see Chapters 11 and 12): (i)
Decomposition by loss of a side group (probably by a free radical mechanism, possibly activated by radical initiators), CH2
CH
CH
+ HX
CH
X
O where X =
Cl(PVC),
O
C
CH3 (poly(vinyl acetate)).
The Lewis acid, HX, promotes further decomposition eventually giving a conjugated polyene (W6 conjugated bonds are coloured). The mechanism is possibly, H CH2 HC Cl
H C
CH2
CH
CH
CH
Cl
Cl
Cl
(-H and -Cl (=HCl)) H
H
HC
CH
Cl
Cl
C H
H C
HC Cl
CH2
+ MZCl
CH
C
CH
Z
Cl
Cl
stable
-HCl
H C
H C
CH
Cl
H C
H
CH2 C H
allylic Cl (labile)
HC
MZ2
H C
C
CH2 C H
CH Cl
Cl allylic Cl (labile) etc.
Thermal stabilisers for PVC are often heavy metal stearates (lead, barium), tin thiolates (R2Sn(SR2) = MZ2), and work by reacting the allylic
90
(ii)
J.P. Candlin
chloride (which is labile) to form stable compounds. Other stabilisers for PVC are metal salts of maleic acid, which possibly work by a Diels-Alder reaction with the intermediate unsaturated conjugated system. If the PVC is used for food applications (e.g., squash (fruit juice) bottles, chocolate dividers in chocolate boxes) calcium mercaptides may be used. Depolymerisation (un-zipping). The main chain is broken and radicals are formed, which can then undergo intra-molecular rearrangement, e.g., H2 C
H2 C
H2 C
H2 C
H2 C
CH
CH
CH
CH
X
X
X
X
+
CH2
CH
CH
X
X
breakage
H2 C CH
+
X
H2C CH X (monomer)
etc. (leading to depolymerisation)
(iii)
This depolymerisation is inherent in the polymer structure and can be prevented by either making a copolymer (such that when un-zipping reaches the co-monomer moiety it is stopped from going any further (e.g., POM (polyoxymethylene) in which a few percent of ethylene oxide has been incorporated), or by using free radical traps (see anti-oxidants). When depolymerisation occurs, high percentage yields of monomers may be obtained, e.g., POM (100%), PMMA (95%), PS (40%), natural rubber (20%). This information can be utilised in recycling of defect materials by conversion back to the monomer. If the homopolymer decomposes at the fabrication temperature another approach is to make a copolymer that can be melt processed at a lower temperature. For example, polyhydroxybutyrate decomposes at the processing temperature (1901C), whereas the copolymer with valeric acid can be processed at B1601C without decomposition. These aliphatic polyesters are biodegradable and most importantly, the decomposition products are not toxic, hence their use in medical applications (e.g., sutures).
91
Polymeric Materials: Composition, Uses and Applications
(iv)
Random chain scission. The initial attack is the same, but an intermolecular reaction occurs. H2 C
H2 C CH X
CH X
formation by bond breakage -see above
+
H2 H2 C C CH H C X
X
H2 C
H2 C CH X
H2 C
H2 C +
CH2 X
C
CH
X
X
+
HC
undamaged polymer chain
H2 C
CH2 C X
X (which can attack undamaged polymer)
When this decomposition occurs the degradation does not give high monomer yields (compared with un-zipping); the products tend to be low MW products. The chain scission and propagation is inhibited by free radical traps (see anti-oxidants). Sometimes heat de-stabilisation is actively sought, e.g., (i)
(ii) (iii)
Mastication. If the MW of the polymer is too high resulting in a high melt viscosity (e.g., natural rubber) or the MWD is too broad giving unstable melt processing conditions (e.g., PP) then mastication using high mechanical shear machinery, e.g., twin-screw extruders, results in a melt processible material. Free radical initiators are sometimes added to accelerate the process. This works by preferentially cleaving the longest chains, thus lowering and narrowing the MWD. Manufacture of carbon fibres, e.g., PAN fibres can be controllably decomposed in an inert atmosphere to give high carbon content fibres. Ablative materials. These polymers decompose to give off volatile materials and a surface char that acts as an insulator (e.g., paints, spacecraft re-entry vehicles). Glass-coated phenolic resins are used in the latter application.
4.1.2 Lubricants These additives reduce the friction between the polymer aggregates or crystallites and also lower the adhesion between the polymer melt and metal surfaces (which occurs in rollers, extruders). This results in: (i)
Lower melt viscosity, thus reducing energy consumption required for processing.
92
(ii) (iii)
J.P. Candlin
Improves the dispersion of fillers and pigments. Reduction of wear of metal surfaces, hence improving polymer gloss, smoothness and surface regularity.
Lubricants can be classified as internal or external lubricants. Internal lubricants should be partially miscible with the polymer at processing temperatures (i.e., behave similar to a plasticiser), but phase separate at ordinary temperatures. Whereas plasticisers are completely miscible with the bulk polymer, lubricants have a limited solubility. Examples of internal lubricants are fatty acid derivatives, e.g., stearates (for PVC), waxes and polyethylene oligomers containing polar groups obtained by partial oxidation. Not all polymers require lubricants; LDPE, nylon and PET are self-lubricating. External lubricants have a lower affinity for polymers and exude to the surface (causing blooming) and act by reducing the adhesion between the polymer and the metal surface during fabrication. Excessive lubrication must be avoided because during extrusion some friction between the screw flights and the polymer is necessary for transporting the polymer through the die. Too much lubrication also causes surface haze. Examples of external lubricants are metal soaps, paraffin waxes, silicones and fluoroplastics.
4.1.3 Slip and anti-slip agents Slip and anti-slip agents are added, especially in film production, to either promote or inhibit slip or sliding of film surfaces, respectively. Their function is to control the surface properties such that there is a balance between adhesion or tackiness of film layers and, on the other hand, the slippage of films. Thus slip agents are added during fabrication of plastics that are in contact, for example, with gears and bearings, whereas, anti-slip agents (adhesion promoters), for example, are incorporated to stop the sliding of plastic rolls or stacked bags.
4.1.4 Anti-blocking agents Because of the high quality of surface smoothness of films, wind-up onto rollers causes adjacent film layers to adhere together, either by static electricity or coldflow (creep). This is overcome by adding finely divided fillers (less than 1 mm diameter) of, for example, chalk, silica, crosslinked polyacrylates, which roughen the surface allowing entrapped air to keep the successive layers apart.
4.1.5 Mould-release agents These materials prevent adhesion between chilled rollers in film production or moulds for injection moulding. They behave like external lubricants, and should serve the following requirements: (i) (ii) (iii)
Form a smooth continuous film on the surface. Good chemical resistance and oxidative stability. No detrimental effect on the polymer surface, e.g., blistering, peeling, streaking, discoloration, poor printability, stress cracking.
Polymeric Materials: Composition, Uses and Applications
93
For injection-moulded articles, although spraying the mould with a release agent is feasible (this is often done for one-off samples) it has many disadvantages, for example, being time consuming or the mould requires cleaning after use to remove residue build-up. For this reason, external lubricants are used. Permanent release metal surfaces can be achieved by treatment with a solution of fluorocarbon oligomers followed by evaporation of the solvent and curing by heat.
4.1.6 Antistatic agents Plastic surfaces can become electrostatically charged through friction, either during processing or post-fabrication handling. This generates several disadvantages: (i)
(ii)
(iii) (iv)
Attraction of dust, which leads to unsightly appearance or malfunction, in applications such as plastic furniture, recording tapes, CDs and DVDs, and packaging. Electrostatic shock from apparel and carpet fibres and plastic floor coverings. This can constitute a fire hazard when handling flammable solvents or fine powders. An uneven feed problem in the hopper (often called bridging) when processing polymer powders. Failure of sensitive electronic equipments, e.g., computers, televisions.
Polymers are inherent insulators and have a high surface and bulk electrical resistance. Reduction of the surface and bulk resistivity is achieved by: (i)
(ii)
(iii)
Surface-active antistatic agents. These are hygroscopic materials and, under humid conditions, form a thin conducting layer of water. They are applied by spraying or dipping and are classified as external antistatic agents. They are not resistant to contact with solvents and can be removed by rubbing. Examples include: cationic (quaternary ammonium, sulfonium or phosphonium salts), anionic (long-chain, sulfonic, phosphonic salts) or non-ionic (ethoxylated fatty acids, sorbitol fatty esters). Internal antistatic agents are added to the bulk polymer before fabrication. They have a low affinity for the parent polymer and migrate to the surface. They offer long-term protection against electrostatic charges. They can be added as a master-batch or concentrate (similar to many additives), which can be diluted as required. Contact food approval has been granted for many of these additives with the exception of some anionic compounds. Conductivity additives (or fillers). These compounds reduce the resistivity of the bulk and the surface of the polymer. Below 10–20% concentration, the resistivity is not affected until a threshold is reached and conduction is observed. Examples include: carbon black, metal powders or fibres (copper, aluminium and silver) and some conducting conjugated polymers. Increasing the concentration of these additives yields conducting polymers that are used for shielding against electromagnetic interference (EMI).
94
J.P. Candlin
Conversely, cling film (plasticised PVC/PVDC, (poly(vinyl chloride)/poly (vinylidene chloride), copolymer, which has very high gas-barrier properties) on peeling from a roll generates static electricity thus promoting adhesion to a surface, e.g., ceramics, but not metallic surfaces which conduct the static electricity away.
4.1.7 Plasticisers Additives that soften and make flexible, hard brittle polymers are called plasticisers. They also lower the processing temperature by decreasing the polymer melt viscosity. This allows conversion of polymers, which may decompose at the processing temperature. They achieve this through lowering the Tg by providing internal lubrication between the polymer chains. However, plasticisation does reduce the heat deflection or distortion temperature (HDT) of the polymer thus limiting their usage temperature. Plasticisers are compatible and miscible with their host polymer causing them to swell and allowing them to be used for coating, moulding, spraying (when used as a suspension in a liquid solvent) or calendering, extrusion and injection moulding (when used as a polymer melt). More than 90% of all plasticisers are used with PVC, the remainder being used with PVDC, cellulose diacetate, poly(vinyl acetate) (PVAC), nylons, urethanes and acrylates. There are several theories for the action of plasticisers: (i) (ii)
(iii)
Decreasing inter-polymer chain attraction in the amorphous region of the polymer thus lowering the Tg. Gels are present in polymer melts. These are formed by high molecular weight physical (chain entanglements) or chemical crosslinks. These aggregates are swollen by plasticisers within the gel allowing movement of the polymer chain. Free volume is the internal space in the bulk polymer not occupied by the polymer chain. Thus deformation and flexibility can be visualised as polymer chains hopping from one engaged volume to a free volume. Plasticisers have a large free volume and this permits more migration of the polymer chains.
The most common plasticisers for PVC are phthalate esters prepared from aliphatic C8 alcohols. For high temperature applications higher molecular weight esters are used, e.g., from mellitic acid, which are resistant to volatilisation and are used for PVC interiors in cars (to prevent fogging of windscreens). Aromatic phosphate esters impart flame retardency (although PVC has good flame retardency). When premium-grade PVC products are required, for example, for extraction and migration resistance, high wearability and low temperature flexibility, polymeric esters made from di-functional acids/alcohols are used as plasticisers, for example, adipic acid/propylene glycol, polycaprolactone and ethylene/vinyl acetate/carbon monoxide terpolymers. With suspension polymerised PVC, the polymer particles are 100–500 mm diameter. They are highly porous and the dry powder will absorb large amounts
Polymeric Materials: Composition, Uses and Applications
95
Figure 2 Two methods for applying surface coating of a plastisol onto an uneven surface. Reproduced with permission from D.H. Morton-Jones, Polymer Processing, Chapman & Hall, London, 1989.
of plasticiser thus allowing PVC to be processed by standard techniques, e.g., extrusion. In contrast, with emulsion polymerised PVC the small polymer particles (0.1 mm diameter) are essentially non-porous and when mixed with a plasticiser a mobile mixture called a plastisol (or paint) is produced. On heating to about 1601C, the plasticiser becomes absorbed into the PVC to give a flexible polymer. Plastisols are frequently used for coating materials (e.g., fabric (leather, floor covering), paper (wall-paper), car-body underseal). Two methods of plastisol coating are shown in Figure 2 depending on whether a flat surface (using a knife-on-roller method) or even-thickness coating (reverse roll coating) is required. The use of plasticisers, with other than PVC applications, is extensive. Many polar rubber sealants or caulking materials are plasticised in order to make them more pliable, e.g., polysulfides, polychloroprene (Neoprenes), nitrile rubber. Esters, similar to those employed with PVC, are used to render cellulose diacetate (‘‘Acetate’’) overhead projection sheets more flexible.
4.1.8 Blowing or foaming agents Blowing and foaming agents are solids, liquids or gases (the latter used under pressure) such that when heat and pressure are applied under processing conditions they generate a gas thus producing a foam or cellular plastic. Careful control of process variables (temperature, time and pressure in the moulds) and the nature of the blowing agent is necessary. The amount of blowing agent can vary from less than 0.1 wt% to 5–15 wt%. The former small concentration is added to counteract depressions in thick sections, which occurs in injectionmoulded articles because of the large volume shrinkages of polymers on solidification. The higher concentrations yield lightweight packaging materials, sponge rubber articles, etc. Foamed polymeric materials can have either a closed or open cellular structure. Closed cells tend to be favoured when the pressure is maintained during the expansion. Both types are used for different applications, e.g., closed for thermal and sound insulation, open cell for soaking up liquids by capillary
96
J.P. Candlin
action. Weight for weight, foamed plastics are stiffer than non-foamed plastics. Although most foamed plastics are fabricated using injection moulding, expanded polystyrene articles are compression moulded using pre-formed expanded beads. Foams can be rigid, semi-rigid or flexible. This depends on the nature of the final polymer. Thermoset polymers yield rigid foams, whereas elastomers give flexible materials. The size of cells varies from 50 to 100 mm and depends on the polymer and its end use. Cells of uniform size are a necessity. Small, uniform cells are formed by addition of nucleating agents. These are finely divided solids, e.g., silicates, and are particularly useful with physical blowing agents. There are two forms of blowing agents (physical or chemical) and these must satisfy the following requirements: (i) (ii) (iii) (iv) (v) (vi)
Long-term storage stability. Gas release in a controlled temperature, time and pressure range. Low toxicity, odour and colour of both the blowing agent and its decomposition products. Does not affect the stability and processing conditions of the polymer. Produces cells of uniform size. The gas must not diffuse out of the polymer matrix during fabrication too quickly, causing the foam to collapse.
4.1.8.1 Physical blowing agents. These are usually compressed gases (e.g., CO2, N2). These gases, which dissolve in the molten polymer under pressure, are released as bubbles when the pressure is reduced. Nucleating agents are frequently used. Low boiling liquids, e.g., pentane, perform the same function. Originally low temperature boiling chlorofluorocarbons (CFCs), for example CFC 11 and CFC 12, were used for closed cell materials. These have low thermal conductivity when compared with air, CO2 and similar gases, and hence made excellent foamed thermal insulators. CFCs have now been withdrawn because they are responsible for stratospheric ozone depletion. 4.1.8.2 Chemical blowing agents (CBAs). These are solids that decompose to give a gas at the processing temperature. In addition to the demands above, the CBA must possess the following: (i)
(ii) (iii)
The decomposition temperature must be matched with the processing temperature of the polymer (which can be in the range 150–3501C). The decomposition must be rapid (less than one minute) and within a narrow temperature range. The CBA should give a high yield of gas (B200 ml/gm). The blowing agent should have a narrow particle size range (to give cells of uniform size) and be easily dispersed in the polymer.
Very few CBAs have been developed for use with polymers for food contact applications. The most commonly used CBA, which has approval, is powdered wax-coated sodium bicarbonate/citric acid, which decomposes at 160–2101C
Polymeric Materials: Composition, Uses and Applications
97
giving off CO2. The azo compound 1,1-azobisformamide (ABFA), which decomposes giving N2 at B2201C, has also approved food contact use and is employed with PVC plastisol, LDPE, HDPE, PP, EVA and PS. For higher melting polymers, for example, PC, nylon, PET, which require temperatures greater than 3001C for fabrication, blowing agents which decompose at this higher temperature are used, e.g., substituted tetrazoles which give off nitrogen gas. The surface finish of injection-moulded foamed articles are not ideal because of external defects, burst bubbles, etc. This can be avoided by sandwich moulding. This is accomplished by initially injecting a slug of polymer melt into the mould followed immediately by a polymer containing a blowing agent, which chases the initial polymer into all the interstices. Embossed wallpapers (‘‘blown vinyl’’) are made by continuously coating a roll of paper with a liquid PVC plastisol containing a blowing agent. This is then passed through a heating oven causing the plastisol to expand. This is immediately followed by an embossing roller that develops a repeating relief pattern. Cushionflors vinyl floor coverings uses a different technique. This uses the plastisol and a CBA containing a ‘kicker’ or accelerator, e.g., ABFA and ZnO. This mixture decomposes at B1901C compared with B2201C without the kicker. When an ink pattern is printed on the plastisol surface it contains an inhibitor (e.g., fumaric acid and trimellitic anhydride), which complexes the kicker ZnO and prevents it from accelerating the decomposition of the CBA. A final layer of plastisol without the CBA is spread onto the surface, see Figure 3. On heating to B1901C the non-inked areas expand, whereas the inked areas (containing the inhibitor) do not swell. Familiar patterns (tiles, floral) with a relief are produced. A different method of making foams is to generate the blowing agent at the same time as the polymer is being formed. Thus urethane polymers are prepared
cross-section profile
Backing
Coated with plastisol + CBA + kicker (ZnO)
Print; ink, contains inhibitor (fumaric acid)
Coated with transparent wear layer (plastisol without CBA)
Heat to 190°C. Foam produced only in the absence of ink
Figure 3 Cushionflors techniques for obtaining printed/relief PVC plastisol floor covering. Adapted with permission from D.H. Morton-Jones, Polymer Processing, Chapman & Hall, London, 1989.
98
J.P. Candlin
by reaction of di-isocyantes and diols in the presence of catalysts (tertiary amines, tin compounds),
OCN
R
NCO + OH
R′
OH
CONH
R
NHCOO
R′
O n
polyurethane
where the hydrocarbon groups, R and Ru, determine the nature of the polymer. If water is present in the diol, or adding water to the low molecular weight prepolymer (which contains isocyanate end groups), reaction with di-isocyanates generates CO2, R
NCO + H2O
RNH2 + CO2
This acts as a blowing agent. If this is the sole source of blowing agent then, again, dependent on the groups R and Ru, flexible foams are generally made by this route. Rigid foams are often made by the addition of a physical blowing agent, e.g., volatile liquids.
4.2 Chemical property modifiers 4.2.1 Anti-oxidants These prevent or retard the autoxidation by atmospheric oxygen of polymers, which often leads to discoloration, embrittlement, cracking, reduction of gloss, and a loss of mechanical properties. They are used in the manufacture of plastics, films, fibres, elastomers, paints, adhesives, etc. The actual mechanism of deterioration varies with the parent polymer, but they all involve radical pathways. The initiation can come from catalyst residues (metallic and nonmetallic), contamination from reactor vessel, UV light or processing equipment or from heat and mechanical processing treatment of the finished polymer. Many of the disintegration pathways involving radicals are common to both autoxidation and decomposition by UV light (see Chapters 11 and 12). The anti-oxidant itself is often consumed in performing its function, although hindered amine light stabilisers (HALS) are self-regenerating. Depending on the polymer, their concentration in the polymer may vary from a few parts per million (e.g., in PE) to several per cent (e.g., in ABS, natural rubber). Because it is impossible to determine all the polymer down-stream end uses, nearly all have food contact approval. To fulfil their role, anti-oxidants must have the following properties: (i) (ii) (iii)
They must be thermally stable and non-volatile at processing temperatures. Be miscible in the polymer. Not leach out of the polymer when in contact with solvents.
Polymeric Materials: Composition, Uses and Applications
(iv) (v)
99
Not corrode the processing equipment with acidic decomposition products. Must be odourless, tasteless and non-coloured (including its degradation products).
Oxidative degradation of polymers is initiated by radicals (Rd) generated in the polymer by heat or mechanical shear during processing or by exposure to UV light. These radicals, in turn, react with O2 to form peroxy and hydroperoxide radicals that promote radical reactions. energy RH
R +H O2 (peroxy radical)
ROO RH
ROOH (hydroperoxide)
ROO + RO + H2O
RO + OH
ROOR where RH = polymer
Thus, if formation of the initial polymer radical (Rd) can be prevented or, if formed, can be rendered harmless, then the stability of the polymer will be enhanced. Polymers that are easily capable of forming radicals are those containing tertiary C–H and allylic C–H groups, e.g., H2 C
H2 C
energy
CH
C CH3
CH3 polypropylene back-bone
H2 C
attack on tertiary group
H C C H
H2 C
H2 C
energy C H2
poly 1,4-butadiene back-bone
H C
H C C H
attack on allylic group
C H2
100
J.P. Candlin
Polymers containing no secondary or tertiary C–H or are aromatic (PEEK or Kevlars) or perfluorpolymers (PTFE) are generally resistant to oxidation and require no anti-oxidant additives. However, the high temperature necessary for curing or fabrication of high performance polymers (especially for aerospace applications) can cause oxidation. For this reason, these materials are often prepared and fabricated under a nitrogen atmosphere. Anti-oxidants can be divided into two classes depending on which part of the radical chain they quench. Primary anti-oxidants are radical scavengers and will react with alkyl chain radicals (Rd) or hydroperoxides (ROOH). Secondary antioxidants work in combination with primary anti-oxidants and principally act by converting peroxide radicals (ROOd) into non-radical stable products. Synergism often works when both classes are used together.
4.2.1.1 Primary anti-oxidants. These are sterically hindered phenols and amines (HALS) and aromatic secondary amines. They intercept the radicals as they are formed: O
OH (H3C)3C
(H3C)3C
C(CH3)3
C(CH3)3
R + RH
CH3
CH3 2,6-di-t-butyl-p-cresol (butylated hydroxy toluene, BHT)
The resulting phenoxy radicals are stabilised by: (i) (ii)
Steric hindrance by the bulky t-butyl groups and therefore cannot attack new polymer chains. Resonance to give canonical forms that can dimerise and generate a new anti-oxidant dimer.
(H3C)3C
(H3C)3C
(H3C)3C
C(CH3)3
dimerise O (H3C)3C
CH3
HO (H3C)3C
CH2
HO (H3C)3C
CH2CH2
OH C(CH3)3
Polymeric Materials: Composition, Uses and Applications
(iii)
101
Formation of a quinoid structure.
(H3C)3C
(H3C)3C
O
CH3
O CH3
(H3C)3C
(H3C)3C R
(H3C)3C R O CH3 (H3C)3C
which can react with further radicals. However, quinoid structures do impart a yellow colour to the polymer. A major problem with BHT is that at elevated temperatures volatilisation may occur. Higher molecular weight hindered phenols can be used. Aromatic amine radical scavengers that are derived from 1,4 di-aminobenzene or diphenylamine are also used.
RHN
NHR
R = alkyl group
CH3 Ph
C CH3
CH3 NH
C
Ph
CH3
These act similarly to the phenol anti-oxidants; the N–H group in the amine reacts with the polymer free radical Rd to give a stabilised nitrogen radical and RH. Amine anti-oxidants are more effective than hindered phenols. Thus they are used with unsaturated elastomers and rubbers, which readily form radicals.
102
J.P. Candlin
Similar to phenols, they can cause staining and are often used in conjunction with carbon black filled elastomers (e.g., tyres) — although carbon black itself has antioxidant capacity. For non-staining applications, e.g., polypropylene carpets, a sterically hindered amine is used, e.g., H H3C
CH3
N
H3C
CH3
2,2,6,6-tetramethyl piperidene
These compounds also inhibit photo-oxidation and are known as HALS. The mechanism is thought to be (R is the polymer group):
H
R
O
N
OR
N
N
O2
ROO
R = O + ROH
A high level of stabilisation is achieved at low concentrations. This is because of a cyclic process whereby the HALS are regenerated rather than consumed during the stabilisation process. This also promotes long-term protection. To avoid leaching of the anti-oxidant when in contact with oils (vegetable and mineral), petrol and solvents, polar amine compounds are used: O NH
NH
S
CH3
O
Alternatively, an amine monomer that can be incorporated into the polymer chain during polymerisation can be used, e.g., CH3 NH
NH
methacrylamide derivative
CO
C
CH2
Polymeric Materials: Composition, Uses and Applications
103
4.2.1.2 Secondary anti-oxidants. These compounds react with the hydroperoxide and peroxide intermediates. They are usually di-valent sulfur or tri-valent phosphorous compounds:
ROCOCH2CH2 2S
H3C
O
P 3
They function by reducing the intermediates to the corresponding alcohols: R′2S + ROOH
R′2SO + ROH
R′3P + ROOH
R′3PO + ROH
Synergy between primary and secondary anti-oxidants occurs and often a mixture is employed. Also included are metal complexing agents, e.g., EDTA (ethylenediaminetetraacetic acid), citric acid, the purpose of which is to deactivate extraneous metal ions that catalyse polymer oxidation.
4.2.2 Anti-ozonants Although only 10–50 ppb ozone is present in the atmosphere at ground level, higher concentrations occur near photocopying machines; this is sufficient to degrade polymers, especially those with unsaturation in the polymer chain, e.g., elastomers. O
O
O
O
O
O
CH
CH
CH +
CH
O3 CH
CH
polymer chain
ozonide
bond breakage
This can cause surface cracks perpendicular to the direction of stress; stretched elastomers are more susceptible to this cracking. Ozone degradation is a surface phenomenon and hence a physical antiozonant must form a protective barrier. A chemical anti-ozonant can be added during polymer fabrication, but again it must diffuse to the surface. It must also provide a defence over the lifetime of the article. Anti-ozonants can function in different ways: (i)
By diffusing to the surface and forming a physical layer between the elastomer and ozone. Paraffin waxes (CnH2n+2 where n = 20–50) behave in
104
(ii)
(iii)
J.P. Candlin
this manner — there is no chemical reaction between the wax and ozone. Care must be taken when the article is exposed to solvents (e.g., petrol), which may dissolve the protection. Reaction with ozone directly. This reaction must be more rapid than the reaction of ozone with the polymer. Examples include aromatic amines, e.g., 1,4-diaminobenzene derivatives. Although not illustrated in the reaction scheme above, the down-stream reaction pathways involve radicals. Therefore, anti-oxidants that scavenge these radicals are also added.
4.2.3 Ultra-violet stabilisers UV stabilisers protect polymers by restricting UV penetration to the surface and therefore confine the damage to surface layers. Protection is important because the energy possessed by UV radiation is sufficient to break chemical bonds. The initial breakage can either be by a radical (Norrish type I) or non-radical (Norrish type II) pathway. The effects are similar to degradation of the polymer by oxidation routes; the radical intermediates can be neutralised by anti-oxidants. Many polymers contain chromophores, which may be a result of their chemical structure or generated during their preparation or fabrication, arising from monomer, solvent, trace metal and catalyst residues. These chromophores will absorb UV light and be excited to a high-energy state. Examples include olefinic, aromatic and ketonic groups. This energy can be lost by radiation, e.g., fluorescence or phosphorescence, or heat or energy transfer to neighbouring chromophores. If none of these pathways are available, photodegradation takes place with bond cleavage and the possible formation of radicals. These radicals react with oxygen to form perxoy radicals and hydroperoxy compounds. Photoexcitation can also act like a sensitiser and convert relatively non-reactive ground-state triplet oxygen into highly reactive singlet oxygen, which again will promote autoxidation of the polymer. Polymers containing keto groups are particularly susceptible to photodecomposition (indeed they are often added to stable polymers to make them photo-degradable). Norrish type I (radical): O CH2
CH2
C CH2
O
UV CH2
CH2
C
CH2
+ CH2
radical decomposition
CH2 + C O
CH2
105
Polymeric Materials: Composition, Uses and Applications
Norrish type II (non-radical): O CH2
C
O
H
UV
CH2
CH
H2C
CH2
non-radical decomposition
H +
C CH2
HC
H2C
O CH2
H
C C H2 O
CH2
C CH3
Several techniques can be used to stop UV degradation: (i) (ii) (iii)
Screens or coatings. These block out UV radiation, e.g., pigments (TiO2), carbon black. Radical scavengers, which intercept the generated radical pathways — similar to anti-oxidants. Often HALS are used. Energy quenchers. These absorb energy from the photo-excited state of reactive singlet oxygen and dissipate it as heat. They are often metal chelates and their action is:
UV chromophore
excited chromophore
triplet O2 quencher
singlet O2 (reactive)
quencher chromophore + excited quencher
quencher + heat
106
J.P. Candlin
Examples of energy quenchers are:
octyl
O S
S NH2R
Ni
M
C
RN2
S O
octyl
2
where M = Ni or Co
(iv)
These compounds are multifunctional additives. They can act as heat stabilisers, radical traps, decompose hydroperoxides, UV absorbers, etc. UV absorbers. This is the largest class of UV stabilisers. They work on the same principle as sun-screen lotions; they contain chromophores that can absorb light in the 280–400 nm region and release the excess energy as heat and not high-energy radiation. They must be stable under processing conditions and should not react with the polymer nor decompose with UV radiation.
Because it is the UV-B radiation (280–320 nm) that causes the degradation, the absorption spectra of the UV-absorber must coincide with these wavelengths. UV-A (320–400 nm) does not cause damage (it is not energetic enough) and UV-C (wavelength less than 280 nm) does not reach the troposphere (it is filtered out by ozone in the stratosphere). The problem is to find an additive that absorbs UV-B but does not have an absorption ‘‘tail’’ in the UV-A and visible wavelengths, and therefore would have a yellow appearance. Many UV absorbers are based upon either 2-hydroxybenzophenone or 2hydroxytriazole derivatives, (the corresponding 3-hydroxy-compounds are not effective). These work via the following mechanisms: H
H O
O
O UV
C
energy absorption
O
C
release of energy (as heat) H
O
UV energy absorption
N
H N
N N
O
N heat release
N
To increase the longevity, UV absorbers with reactive groups which can be incorporated into the polymer chain or high molecular weight substituents are
Polymeric Materials: Composition, Uses and Applications
107
used. Because many of the decomposition pathways involve radicals, a combination of anti-oxidants and UV stabilisers are often employed.
4.2.4 Flame retardants Many polymers are inherently flammable. Furthermore, they often melt, volatilise and emit flammable and toxic vapours. Legislation now dictates the many polymers used in construction, fibres, furniture, advertising signs in shopping malls, must possess combustion resistance. The combustion cycle may be represented as shown in Figure 4. The initial step is the thermal degradation of the polymer giving rise to volatile products. At this stage there is probably no involvement of oxygen. These volatile products, e.g., monomers by depolymerisation, react with oxygen to give heat and flames, which does not involve radicals. Heat liberated by the flames causes further degradation of the polymer, which, together with the initial source of ignition, promotes further combustion, etc. Interference with any of these steps will stop or delay total combustion. These include: (i) (ii) (iii) (iv)
Use thermally stable polymers. Promote char formation, (many of the advanced materials have high char yields). Use radical scavengers. Use endothermic reactions to counterbalance exothermic combustion.
Many of these approaches have been employed to contribute to fire or flame retardency: (i)
Use polymers with naturally low flammability. The threshold of polymers can be qualitatively estimated by determining the LOI of the polymer. This gaseous products
flame gas phase oxygen
volatile products
heat
heat from ignition source
thermal degradation
solid polymer char residue
phase boundary
heat
thermal oxidation
Figure 4 Combustion pathways illustrating the burning of polymers.
108
J.P. Candlin
uses polymer samples of a standard size, and is measured by recording the volume percentage of O2 in an O2/N2 mixture that will sustain flaming combustion for 3 min after the source of the ignition has been removed. Some examples of LOI are: Polymer
LOI
Polyoxymethylene Polyethylene and polypropylene Poly(methyl methacrylate) Polystyrene Cellulose Poly(ethylene terephthalate) Nylon 6 and nylon 6,6 Polycarbonate Poly(phenylene oxide) Aramid (Kevlars) PES and PEEK PVC (unplasticised) PVDC (unplasticised) Carbon (char) PTFE
15.3 17.3–17.6 17.5 18 20 22 23–26 29 31 31 35–37 45 60 65 90
(ii)
↑ flammable ------- air -----------↓ non-flammable
Adding flame retardant additives. These reduce the efficiency of combustion by: a. Cooling of the polymer’s pyrolysis zone, e.g., aluminium trihydrate, Al2O3.3H2O (used in B50% of applications). Above 2501C, water of hydration evolves endothermically thereby lowering the temperature of the flame and diluting flammable gaseous pyrolysis products. Additionally, the residual Al2O3 provides a thermal barrier by coating the polymer surface. Al2O3 also suppresses smoke generation. b. Reducing radical pathways. The most important propagating combustion reactions are: Hd þ O2 ! HOd þ Od
ðexothermicÞ
Od þ H2 ! HOd þ Hd ðexothermicÞ Organo halogen compounds (RX, where X = Cl, Br) on heating generate HX by reaction with the polymer (poly–H): RX Ð Rd þ Xd poly H þ Xd Ð polyd þ HX H2 þ Xd Ð Hd þ HX which react with the free radical propagating intermediates to give less reactive species: Hd þ HX Ð H2 þ Xd HOd þ HX Ð H2 O þ Xd
Polymeric Materials: Composition, Uses and Applications
109
Either high melting point compounds (often aromatic bromine compounds) or halogen-containing monomers that have been incorporated into the polymer (e.g., p-bromostyrene in PS) can be used. If antimony compounds (e.g., Sb2O3) are also included, a synergistic interaction occurs forming SbX3, which is a very efficient radical trap: Sb2 O3 þ 6HX Ð 2SbX3 þ 3H2 O
(iii)
(iv)
Furthermore volatile SbX3 decomposes in the heat of the flame to generate fine particles of Sb2O3, which form sites for radical recombination. A problem with these gas-phase radical quenching agents is that the volatiles emitted are acidic and corrosive. Promoting char formation by adding phosphorus compounds (e.g., red phosphorous or ammonium polyphosphate, (NH4PO3)n). These additives cause the polymer to swell (intumescence) and form a carbonaceous char on the polymer surface that thus insulates the bulk of the polymer (ammonium polyphosphate is particularly useful for cellulose textile fibres (e.g., cotton)). Melamine and melamine salts (e.g., borates, phosphates) act in a similar manner promoting char formation and intumescence. Thermosets or highly crosslinked polymers give high char yields. Similarly, many high performance polymers, e.g., PEEK, PES, polyetherimide (PEI), not only have high LOI values but also tend to decompose to a char. Surface oxygen barrier formation by using boron compounds (e.g., H3BO3, borax (Na2B4O7)). They prevent combustion by forming a glass-like coating. They are not very efficient, but they are not expensive.
Allied to flammability is smoke density suppression especially in confined spaces, e.g., airliners, houses, warehouses. Many aromatic compounds burn with a smoky flame (e.g., styrene), whereas corresponding aliphatic compounds tend to burn with a clean ‘‘transparent’’ flame. This is because air-borne poly-aromatic vapours decompose to give volatile carbon (smoke) in low oxygen environments. Finely divided magnesium or aluminium hydroxides (or a 3:1 combination) are currently the best smoke suppressants. They also neutralise the acidic vapours produced from halogen-containing flame inhibiters. The more finely divide they are the more efficient they become. Unfortunately, most fatalities in fires occur by inhalation of toxic vapours. These can be carbon monoxide (which arises from incomplete combustion), cyanides (from nitrogen-containing polymers) and chlorides (from chloropolymers). These are the adverse consequences of flammable polymer combustion. They can be overcome by using breathing apparatus, face masks, etc.
4.2.5 Biocides (also called fungicides, bactericides, slimicides, anti-microbials, etc.) Most polymers of high molecular weight in their pure state are resistant to attack by microorganisms, for example, although commercial polyethylene is resistant,
110
J.P. Candlin
oligomers of less than 600 MW are eventually consumed. Bacterial attack on the polymer can lead to discoloration, mildew, odours, embrittlement and eventually structural degradation and product failure. Ironically, an active field of research is to promote bacterial degradation in landfill sites. Most trading polymers contain a variety of additives, e.g., plasticisers, lubricants, stabilisers, etc., and it is these additives that promote bacterial attack on the polymer. At the same time, degradation by other routes provides pathways for bacterial attack by creating hydrophilic surfaces. Because many industrial and domestic services are supplied by underground plastic pipes and cables, care must be taken when choosing additives to make sure that the polymer is not vulnerable to attack. There are two considerations to be applied when using biocides: (i)
(ii)
Reduce the amount of biocide. This is particularly true for plasticised PVC. Alternatively choose plasticisers that are less liable to attack. Thus aliphatic plasticiser esters are very prone, whereas phthalates, polymeric esters and chlorinated hydrocarbons are fairly resistant. To be effective the biocide should migrate to the surface of the polymer in sufficient concentration to perform its function. This migration should not occur too quickly (bacterial attack is a slow process, sometimes taking years to begin) or it will be leached away.
Not all additives increase biological attack. Heat stabilisers for PVC fabrication, e.g., tin and lead organometallic compounds, promote fungal resistance. Biocides are naturally toxic to lower organisms and therefore must be handled with care. Strict government rules control the sale and use of biocides, especially those used in food contact applications. They are added at the fabrication stage. The morphology of the polymer article is important, e.g., high surface area articles, such as foams, biodegrade more rapidly. The use of biocides is spread across the whole polymer range, e.g., paints, ropes, textiles, fibres, etc. Many are copper, silver or arsenic compounds and also various heterocyclic compounds, e.g., isothiazolines (which have some structural resemblance to penicillin).
4.2.6 Anti-fogging agents Fogging of plastic films used for packaging or agriculture, spectacle lenses, crash helmets, etc., is caused by water droplets. This decreases the transparency and is aesthetically not desirable. Surface-active agents may be added during the processing of films (internal addition) or by surface treatment of the film (external addition). These tend to reduce the surface energy of the film/water droplet interface promoting a continuous film of water thus enhancing transparency. Examples include hydrophilic surfactants, such as sorbitol or glycerol fatty acid mono- or di-esters. If the packaging is in contact with food it must have the necessary approval.
Polymeric Materials: Composition, Uses and Applications
111
4.2.7 Degradation additives This is a relatively recent area of research and development. It has come about because of various reasons: unsightly plastic articles, over-flowing landfill sites, enhancing humus in soils thus avoiding combustion methods that may generate toxic vapours, etc. These additives promote disintegration of polymers into non-toxic low molecular weight fragments through various routes. This is achieved by thermal, photo-oxidation, hydrolytic, chemical, mechanical or biological pathways. Many degradation avenues are available: random chain scission, side group elimination and un-zipping of the polymer chain. Three main routes have been followed: (i)
(ii)
(iii)
Photodegradation. This involves initiation by sunlight or UV radiation. The intermediate radicals eventually lead, via hydroperoxides and peroxides, to organic carbonyl compounds. These, in turn, are oxidised to carboxylic acid derivatives, which are biodegradable. The blending of polymeric organic carbonyl compounds, e.g., ethylene/carbon monoxide copolymer, with the parent polymer, e.g., polyethylene, gives a plastic film material that degrades within 3 months. Although dithiocarbamates of nickel(II) and cobalt(II) are multifunctional for the prevention of heat and UV degradation, the iron(III) analogue behaves differently. Initially, when added to the polymer it acts normally, but after an induction period (1–2 weeks) it functions like a photo-degradent. Furthermore, the time for the polymer film to degrade to flakes can be controlled by the amount of iron(III) dithiocarbamate added. For instance, when used in agriculture the complete breakdown of the film can be timed to coincide with the harvesting season. The degradation period can be controlled from weeks to 1–2 years. Biodegradation. This principle is to blend a completely biodegradable polymer with an inert polymer matrix. Many naturally occurring polymers are biodegradable, e.g., the polysaccharides, pullulan and chitin, in addition to synthetic polymers, e.g., polycaprolactone, polyethylene succinate and poly(vinyl alcohol). The most important additive is starch. This can be blended with polyethylene using water or glycerol as a plasticiser — up to nearly 50% starch, although normally 6–15% is used. Synthetic polymers. A different approach is to use a synthetic polymer that is biodegradable (after initial hydrolysis) and can be processed using standard methods. These include copolymers from hydroxybutyrate/ hydroxyvalerate (made from bacteria), polylactic acid and polyglycollic acid (made from the corresponding cyclic anhydrides). These are too expensive to compete with starch/PE but are used for added-value products, e.g., sutures.
Perhaps the greatest benefit of plastic degradation is in the use of plastic films (e.g., PE, PP) in agriculture, especially as mulching films. This involves the covering of growing plants with film. Gains include: less water required for irrigation, increased temperatures (killing dangerous microorganisms), avoiding
112
J.P. Candlin
rain run-off of fertiliser. The greatest advantage is the ease of disposal; after use, the degraded polymer flakes are just ploughed into the soil.
4.3 Mechanical property modifiers 4.3.1 Fillers and coupling agents Fillers were initially introduced to reduce costs; they have significantly lower cost than low cost commodity polymers. However, fillers are now added to polymers to enhance performance in many applications. Many of these benefits have emerged because of the greater adhesion between the polymer-filler interface. This arises from the use of coupling agents, which provide a bond, both physical and chemical, between the filler and the polymer matrix. The size and shape of the filler plays an important role. Generally, the smaller the size the greater the property improvement. Size distribution is also paramount. Packing of the filler within a polymer matrix is improved when a combination of large and small particles is used (the smaller particles occupying interstices left by the larger particles). Higher concentrations (or loadings) of the filler are possible and improved properties result. The shape also affects the properties of the filled polymer. Thus, using fibres brings about reinforcement of the polymer. The properties that can be affected arising from fillers include: (i) (ii) (iii)
(iv) (v) (vi) (vii)
Improved stiffness or rigidity (modulus). Improved protection from heat distortion. Reduced coefficient of thermal expansion. This reduces the shrinkage that occurs in the conversion melt to solid during processing. Also, compatibility between polymer/metal adjoining closures over the range –201C to 401C. Plastics expand and contract several times that of metals. Alteration of density of the polymer to a either higher or lower value by using solid or hollow fillers, respectively. Reduced creep (long-term stress). Improved abrasion resistance. Increased surface hardness.
Many other specific properties have been noted, e.g., decreased flammability and anti-blocking. Fillers can be grouped into various categories depending on shape. Spherical fillers include calcium carbonate (size B1 mm diameter and quantitatively the most important filler). This can be ground mechanically to a fine powder or, for smaller particles, by precipitation from solutions or slaked lime using carbon dioxide. Dolomite (calcium/magnesium carbonate) and barium sulfate are prepared and applied similarly. Silica can be either pulverised from quartz or flame hydrolysed from silicon tetrachloride to give ultra-fine, sub-micron diameter powder. These fillers increase the density of the base polymer. Decreasing the density can be achieved using hollow glass microspheres, flyash (from coal-burning power stations) or volcanic ash.
Polymeric Materials: Composition, Uses and Applications
113
Other spherical fillers include carbon black. This has several roles particularly in combination with elastomers, e.g., black pigment, anti-oxidant and UV stabiliser, reinforcing filler, and an electrical conductor when used at 60% concentration. Wood flour is particularly effective in phenol/formaldehyde and melamine or urea/formaldehyde thermoset resins because the phenolic lignin component in the wood reacts with the methylol groups (–CH2OH) in the growing polymer. An important feature of fillers is their aspect ratio (length versus diameter or thickness). When this is large, as occurs in fibres (glass, polymeric and carbon), whiskers, plate-like natural minerals (e.g., micas, talc, kaolin), graphite, etc., many properties are improved, especially tensile strength, rigidity, etc. However, none of these improvements are possible unless the interfacial force between the filler and the bulk polymer is strong enough. Since many of these fillers are inorganic with surface hydroxyl groups a bond between the polymer and filler is likely to be weak. It would also be prone to hydrolytic cleavage. Thus a coupling agent is necessary to bridge the different materials together, and enable transfer of any external stress from the polymer to the reinforcing filler. Coupling agents are chemicals with a dual function. They react with the surface groups (usually hydroxyls) on the filler and contain chemical groups compatible with the polymer matrix, either by physical (e.g., entanglement) or chemical means (e.g., hydrogen bonding, dipole/dipole interaction) (Figure 5). For silica fillers, hydrolytic stability is best when M = Si; for other fillers, e.g., calcium carbonate then titanate- or zirconate-coupling agents are preferred. In some examples it is not necessary to prepare the organometallic-coupling agent R2MX2 beforehand. Thus coating glass fibres with a heptane or alcohol solution of titanium alkoxide promotes adhesion between the fibre and polymer, e.g., acrylic, polyolefins, polyester, polyamide and other thermoplastic resins. Glass fibres dominate this field either as long continuous fibres (several centimetres long), which are hand-laid with the thermoset precursors, e.g., phenolics, epoxy, polyester, styrenics, and finally cured (often called fibre glass reinforcement plastic or polymer (FRP)). With thermoplastic polymers, e.g., PP, short fibres (less than 1 mm) are used. During processing with an extruder, these short fibres orient in the extrusion/draw direction giving anisotropic behaviour (properties perpendicular to the fibre direction are weaker). Glass fibres are fragile and break easily because of surface defects. This is overcome by treating virgin fibres with water-soluble sizing agents. These protect
+ OH
R
X M X
R
-2HX
R
O filler
filler
OH
M O
R
Figure 5 Schematic of the attachment of coupling agent to a filler particle. X = Cl, OCH3, carboxyl; M = Si, Ti, Zr; R = long-chain alkyls or oligomers that contain grafted polar groups, e.g., amides and carboxyl.
114
J.P. Candlin
the glass fibres before usage and can be easily washed off. Sometimes the sizing agents can act as coupling agents.
4.3.2 Impact modifiers This is a growth area — how to improve the properties, particularly impact properties of the base polymer. Many plastics can be either tough or ductile with a high impact strength and can withstand a rapid force without fracturing, or they can be brittle and shatter easily, especially at low temperatures. To overcome this, polymers are blended with a more flexible polymer, which dissipates the energy of impact through facile polymer chain movement. This implies that the impact modifiers must have a low glass transition temperature. Furthermore, they must not be miscible with the parent polymer, in contrast with plasticisers, which must have compatibility with the polymer. They must retain or increase the heat distortion temperature, not lower it as occurs when plasticisers are used. Impact modifiers are added at the blending stage and should be welldispersed discrete particles of diameter B1 mm. They must have good adhesion at the modifier/polymer interface in order to transfer the energy efficiently. Loadings of 5–15% of modifier are usually required to be effective. Transparency is often required. This is achieved by arranging that the particle size of the modifier to be below that of the wavelength of visible light (0.4–0.8 mm). This can normally be achieved by emulsion polymerisation, e.g., polybutadiene, polystyrene. Adhesion and surface compatibility between the polymer and modifier can be achieved by surface grafting of polar groups, e.g., acrylonitrile, various acrylates, onto the impact modifier surface before blending. Crystalline polymers, e.g., nylon, poly(butylene terphthalate), are not easily impact-modified. The crystalline domains can act as crack initiation sites. Amorphous polymers with high Tgs are more amenable to modification, e.g., PS, PVC, PC, although PC is tough because of H-bonding that occurs between the polymer chains. The largest use of modifiers are with PS and PVC. High-impact PS (HIPS) was made originally by mechanically blending polybutadiene (PB) and PS. The current method is to dissolve PB in styrene monomer and initiate emulsion polymerisation. This results in a grafted copolymer with PB acting as the core and PS as the surface graft. This forms a single-phase transparent alloy with PS; the homopolymers PS and PB are non-miscible and will not form a clear blend. There are various requirements for impact-modified PVC. The most demanding is for outdoor sidings and window frames, where lifetimes of 20 years are expected. Because butadiene polymers or copolymers (e.g., acrylonitrile/butadiene/styrene (ABS), methyl methacrylate/butadiene/styrene (MBS)) are susceptible to UV degradation these polymers are usually not employed; instead acrylate polymers are used for these applications. Although the main use of impact modifiers is with thermoplastics, thermosets also benefit. The agent is added at the monomer stage. Thus epoxy polymers can be made less brittle by the addition of rubbers. Care has to be taken that the high temperature properties of the thermoset are not compromised.
Polymeric Materials: Composition, Uses and Applications
115
4.3.3 Nucleating agents Many of the properties of a polymer depend upon the presence or absence of crystallites. The factors that determine whether crystallinity occurs are known (see Chapter 2) and depend on the chemical structure of the polymer chain, e.g., chain mobility, tacticity, regularity and side-chain volume. Although polymers may satisfy the above requirements, other factors determine the morphology and size of crystallites. These include the rate of cooling from the melt to solid, stress and orientation applied during processing, impurities (catalyst and solvent residues), latent crystallites which have not melted (this is called self-nucleation). All of these parameters are not under control. To deliver a more uniform distribution of crystallites, specific nucleating agents are added whilst processing. It has also been shown that many of the desirable properties are the result of small regular spherulites (or nascent crystals). Furthermore, other advantages of controlled nucleation include: (i) (ii) (iii)
Increase of the crystallisation rate. Increase of the temperature at which crystallisation commences on cooling from the melt, thereby reducing injection moulding time. Small crystallite size, less than 0.5 mm, reduces light scattering, thereby making the polymer transparent.
Nucleating agents should possess the following requirements: (i) (ii) (iii) (iv) (v) (vi)
Small particle size (preferably less than 0.5 mm diameter). High melting point. Insolubility in the polymer melt. Surface compatibility with the polymer allowing good dispersibility. Adequate thermal stability with no odour or staining during processing. Have food contact approval.
There appears to be no physical (e.g., crystal habit or morphology) or chemical (e.g., surface groups) correlation to identify which nucleating agent works best with which polymer matrix. However, it is known that dibenzylidene sorbitol works best with PP (it is sometimes called a clarifier because it enhances transparency), and inorganic benzoate salts are successful with PET.
4.3.4 Aesthetic property modifiers These enhance the appearance of the polymer, but play no role in the chemical, physical or mechanical properties of the base polymer. The main difficulty is that if the finished assembled article is made from different grades of the same polymer or from different polymers, then, particularly with different polymers, the combination must be uniform. For example, bathroom suites are often made from different materials, e.g., ceramics, baths (polyacrylates), trimmings (PVC, PP). The colorants therefore have to undergo different processing conditions and it is essential that in the final products the colour is the same.
4.3.4.1 Colorants. This is often the determining feature of a plastic article. Two types of colorants are used: pigments and dyes. Pigments are mostly inorganic
116
J.P. Candlin
and insoluble in the polymer matrix. They should be dispersed uniformly throughout the polymer. Dyes are organic based and tend to be soluble in the polymer. Dyes are liable to be more brilliant and vivid and more transparent than pigments, which are duller and opaque. This is because the colour with pigments is by reflection only, rather than the removal of the complementary colours by dyes. Both pigments and dyes must fulfil the following requirements: (i) (ii) (iii) (iv)
Must be thermally stable under process conditions. Have chemical compatibility with either the base polymer or accompanying additives. Have a reasonable lifetime without fading, colour change, bleeding, etc. Be non-toxic or have food contact approval. Also, on disposal (combustion or landfill) must not generate harmful materials.
Pigments can be either inorganic or organic. White pigments are the most widely used (they are often added with other colorants to give the finished article increased brightness). Titanium dioxide is by far the most important white pigment, since it imparts a high degree of reflectance and whiteness because of its high opacity (maximum light scattering with minimum light absorption). Two crystalline forms exist, rutile and anatase. Rutile (0.25 mm diameter) has the higher refractive index and is capable of greater reflectance in the visible spectrum. Anatase (0.18 mm diameter), on the contrary, scatters and therefore reflects more into the UV part of the spectrum. This confers a bluish tinge, which compensates the yellowness of some polymers. TiO2 actually promotes photoand oxidative degradation of the polymer and at the surface erodes a white powdery deposit of TiO2 results (chalking). This is prevented by initially coating the TiO2 particles with silica and alumina. Other pigments include zinc sulfide (white), iron oxides (brown), chromium oxides (green) and carbon (black). Good dispersibility is essential. To aid this the surface of the pigment is often coated with hydrophobic groups (similar to fillers). Because of toxic considerations, both lead chromate (yellow) and cadmium sulfide (red) are being phased out of usage. Synthetic ultramarines (made by fusing kaolin, sodium carbonate and sulfur) can be manufactured to give blue, pink and violet shades. Organic pigments include azo condensation products and metal phthalocyanins. These tend to agglomerate during compounding giving a spotted appearance. Dyes are miscible with the polymer and hence do not have dispersion problems. They include many of the dyes that have been developed for dying fibres, e.g., azo and anthroquinone derivatives. They are particularly useful for transparent articles, e.g., automotive taillights, decorative film. They can be added either as a dry powder or as a colour concentrate (requiring 10-fold dilution). Colorants have been developed for special effects. Pearlescent or iridescent give an attractive appearance. They are often used for coating paper (e.g., cosmetic packaging). The pigment consists of thin platelets, less than 1 mm thickness, which have a high refractive index, e.g., mica coated with TiO2.
Polymeric Materials: Composition, Uses and Applications
117
Interference patterns with the reflective and refractive light occurs that varies with the viewing angle. Thin metallic flakes of, for example, aluminium, copper, bronze, coated with a dye are used extensively in automobile wheel hub-caps, and ‘‘metallised’’ car-body paint finishes. Optical brighteners, optical bleachers or fluorescent pigments absorb UV light (B350 nm) and instantly emits it in the blue/violet region (B425 nm) of the spectrum. This has the effect of counterbalancing the yellow tinge of many plastics. However, they tend to perform a similar function as UV stabilisers. If they are both present, more brightener has to be added. Typical concentrations are 10–500 ppm and they are often based on stilbene structures. Their main application is in toys, packaging and road/safety signs. Phosphorescent pigments work by absorbing UV-visible light and slowly emitting it at longer wavelength light as an after-glow. Di-valent cation substitution of zinc sulfide is often the most popular choice.
5. SUMMARY The use of plastics in society is increasing at the rate of 5–10% per annum. The main application is in packaging and all the major commodity polymers are involved. Although excess packaging has been blamed for saturating landfill sites, it must be remembered that packaging does reduce the loss of goods which occurs through breakage and especially food spoilage. In the developed world, packaging results in less than 2% food wastage (an improvement from 15% which occurred before World War II) compared with 30–50%, which currently occurs in the under-developed world. Packaging also allows easy handling of goods. Improved tear strength (LLDPE compared with LDPE) has permitted a halving of the amount of polymer used in disposable shopping bags. Over the past 20 years no new commodity polymer has been developed. This is because of the advances in fabrication, blends (both miscible and nonmiscible), fibre reinforcement, etc. Thus films with up to 11 different polymer layers have been developed. High performance polymers are being used to make articles that are normally manufactured from metals. This is because of a higher strength-to-weight ratio. Modern passenger aircraft are now made with an ever-increasing usage of composites (e.g., epoxy/carbon fibres). Military aircraft development has led the way in this area. In the future, plastics and polymers will be important in developing ‘‘smart’’ materials. These are materials that can counteract any external force by reinforcing itself. An example is the repair of cracks in airplane fuselage and wings. Incorporated in the composites are hollow cenospheres containing separately the components for making a thermoset polymer, e.g., epoxy oligomer and catalyst (e.g., amine). As the crack progresses, the cenospheres are broken and the ingredients mix to form a polymer and heal the fracture.
118
J.P. Candlin
BIBLIOGRAPHY There are many reference sources that expand the knowledge of polymer composition, uses and applications. These include scientific encyclopaedias (often arranged in an alphabetic manner), together with speciality books — especially on how additives improve and extend the uses of polymers. In multi-volume references and other specialist books listed below, the ISBN(13) has been given. The original sources can be traced through Internet sites (e.g., GOOGLEs) using, for example, where appropriate, the ISBN number or by searching the title given in italics. 1 2 3 4 5 6 7 8 9 10 11 12
Kirk-Othmer Encyclopedia of Chemical Technology, 5th ed., Wiley, Chichester, 2007. Ullmann’s Encyclopedia of Industrial Chemistry, 7th ed., Wiley-VCH, Weinheim, 2007. Encyclopedia of Polymer Science and Technology, H.F. Mark (Ed.), 3rd ed., Wiley, New York, 2004. Encyclopedia of Polymer Science and Technology, Concise, H.F. Mark (Ed.), 3rd ed., Wiley, New York, 2007. ISBN-13: 978-0470046104. M.P. Stevens, Polymer Chemistry: An Introduction, 3rd ed., Oxford University Press, Oxford, 1999, ISBN-13: 978-0195124446. Polymer Handbook, J. Bandrup, E.H. Immurgut and E.A. Grulke (Eds.), 4th ed., Wiley, Chichester, 2003. ISBN-13: 978-0471479369. A.B. Strong, Plastics: Materials and Processing, 3rd ed., Prentice Hall, New Jersey, 2006, ISBN-13: 0131145580. C.A. Harper, Handbook of Plastics, Elastomers and Composites, 4th ed., McGraw-Hill Professional, New York, 2002, ISBN-13: 978-0071384766. F. Rodriguez, C. Cohen, C.K. Ober and L. Archer, Principles of Polymer Systems, 5th ed., Taylor & Francis, London, 2003, ISBN-13: 978-1560329398. J.C. Salamone, Concise Polymeric Materials Encyclopedia, CRC Press, Boca Raton, 1998, ISBN-13: 978-0849322266. Concise Encyclopedia of Polymer Processing and Applications, P.J. Corish (Ed.), Pergamon Press, New York, 1991. ISBN-13: 978-0080370640. N.P. Cheremisinoff, Concise Encyclopedia of Polymeric Engineering Terms, Butterworth-Heinemann, Oxford, 2001, ISBN-13: 978-0750672108.
Polymer additives: 13 J. Murphy, Additives for Plastics Handbook, 2nd ed., Elsevier B.V., Amsterdam, 2001, ISBN-13: 978-1856173704. 14 Plastics Additives Handbook, H. Zweifel (Ed.), 5th ed., Hanser-Gardner, Cincinnati, 2001. ISBN-13: 978-1569902950. 15 Polymer Modifiers and Additives (Plastics Engineering), J.T. Lutz and R.F. Grossman (Eds.), Marcel Dekker, New York, 2001. ISBN-13: 978-0824799496. 16 Chemistry and Technology of Polymer Additives, S. Al-Malaika, A. Golovoy and C.A. Wilkie (Eds.), Blackwell Science Inc., Malden, 1999. ISBN-13: 978-0632053384. 17 Speciality Polymer Additives: Principles and Applications, A. Al-Malaika, A. Golovoy and C.A. Wilkie (Eds.), Blackwell Science, Oxford, 2001. ISBN-13: 978-0632058976. 18 Plastics Additives: An A-Z reference, G. Pritchard (Ed.), Kluwer Academic Publishers, Dordrecht, 1998. ISBN-13: 978-0412727207. 19 Plastics Additives Handbook, R. Gachter and H. Mu¨ller (Eds.), 4th ed., Hanser-Gardner Publications, Inc., Cincinnati, 1993. ISBN-13: 978-3446175716. 20 Plastics Additives: An Industry Guide, E.W. Flick (Ed.), Vol. 1, 3rd ed., Plastic Design Library/William Andrew Publishing, New York, 2001. ISBN-13: 978-0815514640.
Polymeric Materials: Composition, Uses and Applications
119
21 B. Wendel, Plastic Additives: Guide and Reference, CRC Press, Boca Raton, 2002, ISBN-13: 9781587160752.
The section on polymer additives has been modelled on three articles in the Journal of Chemical Education by M.P. Stevens; these are: J. Chem. Ed., 70(6) 444; 70(7) 535; 70(9) 713; (1993).
This page intentionally left blank
SECTION II: Polymer Chain Analysis
This page intentionally left blank
CHAPT ER
4 Chain Structure Characterization Gregory Beaucage and Amit S. Kulkarni
Contents
1. Introduction to Structure in Synthetic Macromolecules 1.1 Dimensionality and statistical descriptions 1.2 Chain persistence and the Kuhn unit 1.3 Coil structure and chain scaling transitions 1.4 Measures of coil size Rg and Rh 2. Local Structure and Its Ramifications 2.1 Tacticity 2.2 Branching 2.3 Crystallization 2.4 Hyperbranched polymers 3. Summary References
123 123 125 127 132 134 134 139 153 163 165 166
1. INTRODUCTION TO STRUCTURE IN SYNTHETIC MACROMOLECULES 1.1 Dimensionality and statistical descriptions Synthetic polymers display some physical characteristics that we can identify as native to this class of materials, particularly shear thinning rheology, rubber elasticity, and chain folded crystals. These properties are inherent to long-chain linear and weakly branched molecules and are not drastically different across a wide range of chemical make-ups. We can consider these features to define synthetic macromolecules as a distinct category of materials (see also Chapter 2). The realization of this special category of materials necessitated the definition of a structural model broad enough to encompass polyethylene to nylon yet specific enough that detailed analytically available features could be used to define the major properties of interest, especially those native to this class of materials. This structural model for polymer chains is based on the random walk statistics Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00404-2
r 2008 Elsevier B.V. All rights reserved.
123
124
Gregory Beaucage and Amit S. Kulkarni
Figure 1 Two examples of random walks: 10,000 steps on a cubic lattice.
observed by Robert Brown in studies of pollen grains and explained by Einstein in 1905. It is a trivial exercise to construct a random walk on a cubic lattice using a PC (personal computer), see examples in Figure 1. From such a walk we can observe certain features of the general model for a polymer chain. The chain structure differs from conventional structures in that it does not display an obvious surface and incorporates a significant fraction of solvent within the structure. We can notice: (i) (ii) (iii)
the two walks appear different despite using exactly the same algorithm, bunching of steps makes walks seem non-random, in fact bunching is a signature of a random process, and one simulation is of no use in describing the general features of the structure, we must consider a time average or an average over different structures in space.
A classical description of such a structure is of no real use. That is, if we attempt to describe the structure using the same tools we would use to describe a box or a sphere we miss the nature of this object. Since the structure is composed of a series of random steps we expect the features of the structure to be described by statistics and to follow random statistics. For example, the distribution of the endto-end distance, R, follows a Gaussian distribution function if counted over a number of time intervals or over a number of different structures in space, 3 3=2 3ðRÞ2 Pð R Þ ¼ exp (1) 2ps2 2ðsÞ2 This function is symmetric about 0, the starting point as indicated by the symmetric term R2. Since the distribution is symmetric, the mean value /RS ¼ 0 and we must consider the second moment as a measure for the size of the structure, /R2S. For a series of n steps of length lK, where lK is the Kuhn step
Chain Structure Characterization
length, we can consider two contributions to /R2S, n X n n X n n 2 X X X hri ri i ¼ nl2K R ¼ ri rj ¼ ri rj þ j¼1 i¼1
j¼1 iaj
125
(2)
i
where the first term for i6¼j is 0 since there is no correlation in direction between steps i and j and the second term yields the result nl2K since there are n steps where i ¼ j; ri is the position vector of the ith segment. By considering that, Z 2 R ¼ R2 PðRÞdR ¼ s2 (3) we find that the variance, s2 (square of the standard deviation), for the random walk is given by (2), nl2K. Polymer chains in dilute and semi-dilute solutions display a statistical structural hierarchy that differs in essence from the explicit structural hierarchy displayed, for example, by proteins in the native state. In proteins the primary residue sequence gives rise to secondary helical coil and beta sheet structures. These secondary structures compose a complex tertiary structure and higher order associations of protein chains. For synthetic polymers the hierarchy begins with the persistence unit that builds upon short-range interactions in a statistical sense at low chain index difference. Chain persistence can be measured using viscometry, dynamic light scattering or static scattering measurements. Dynamic measurements yield directly the Kuhn length that has been shown to be equivalent to twice the statically measured persistence length. The Kuhn length, lK, is the physical step length for a synthetic polymer chain.
1.2 Chain persistence and the Kuhn unit The persistence length, lP, was introduced by Kratky and Porod [1–3] as a direct measure of the average local conformation for a linear polymer chain. The persistence length reflects the sum of the average projections of all chain segments on a direction described by a given segment. Kratky described the features of the persistence length in a static small-angle scattering pattern; in particular, a regime of dimension 1 in the small-angle scattering pattern corresponds to Kratky and Porod’s definition of the persistence unit [4–6]. The mass-fractal dimension of an object can be directly determined in a scattering pattern through the application of a mass-fractal power-law [7]. Using these laws, an object of mass-fractal dimension df displays a power-law described by, IðqÞ ¼ Bqdf , for 1pdfo3. (B, a constant, is the power-law prefactor, which depends on the system; for example, for Gaussian conditions B is given as, B ¼ 2G=R2g where G is the Guinier prefactor, and Rg is the radius of gyration.) A power-law of 2 is expected for the Gaussian regime, since nBR2, and a power-law of 1 for the persistence regime, where the chain appears to be statistically composed of rods. To resolve the persistence length, lP, a log–log plot of I(q) versus q can be made and the two power-law regimes matched with lines of slopes 2 and 1, Figure 2 [3]. The intersection of these two lines in q
126
Gregory Beaucage and Amit S. Kulkarni
100 8 6
q*Kratky/Parod
4
-2
2
Intensity (cm)-1
10
8 6 4 2
-1 1
8 6 4 2
0.1 0.001
2
3
4 5 67
2
3
4 5 67
0.01
2
0.1
3
4 5 67
1
q (Å)-1
Figure 2 Kratky/Porod graphical analysis in a log–log plot of corrected small-angle neutron scattering (SANS) data from a 5% by volume deuterated-PHB sample in hydrogeneous-PHB (polyhydroxybutyrate). The lower power 2 line is the best visual estimate; the upper line is shifted to match a global unified fit. Key: left, q corresponds to best visual estimate; right, plot to match global unified fit. The statistical error in the data is shown. Reprinted with permission from Beaucage et al. [3]. Copyright 1997, American Chemical Society.
is related to the persistence length through 6/(pqintersection) ¼ lP (see Ref. [4], p. 363). q is the absolute value of the momentum transfer vector, q ¼ 4(p/l) sin(y/2), l is the wavelength of the scattered radiation and y is the scattering angle. (Equivalently, a ‘‘Kratky plot’’ of Iq2 vs. q can be made to account for Gaussian scaling, and the deviation from a horizontal line can then be used to estimate lP. This approach has been summarized in several reviews (see Ref. [4] and Appendix G, p. 401 of [8]). The statistical segment length, lssl, is a related parameter defined as the scaling factor between the chain’s radius of gyration, Rg, and the square root of the number of chemical mer units in the chain, nchem, where Rg ¼ 2lssl(nchem/6)1/2. For a freely jointed, Gaussian chain, where the Kuhn unit is a chemical mer unit, 2lssl ¼ lK ¼ 2lP and nK ¼ nchem. The specific definitions of these terms becomes important for chains with bond restrictions where nK6¼nchem and 2lssl6¼lK, that is, the Kuhn segment and the persistence length are both independently measurable physical parameters while, in most cases, the statistical segment length is an arbitrary parameter which depends on the chemical definition of a chain unit. In general, lK ¼ 2lP as noted above [9–11]. When the global chain scaling deviates from Gaussian, such as in good and poor solvents, the statistical segment length refers to an equivalent-Gaussian chain, which does not physically exist. Even under
Chain Structure Characterization
127
these deviatory scaling conditions, there remains a scaling relationship between lssl and lK [12], and the persistence length and Kuhn step length retain their physical definitions. Although the definition of the persistence length by Kratky and Porod [1,2] appears to be somewhat vague in terms of real space, it is the only physical parameter that can be independently determined that directly reflects local chain conformation at thermodynamic equilibrium. Because of this, the persistence length is a focus of calculations of chain conformation using chemical bond lengths and angles [4,8,13]. In the more complicated chemical structures, seen in biology for instance, such calculations become tedious and are subject to some degree of uncertainty due to the dominance of secondary chain architecture. In fact there has been little experimental verification of ab initio calculations of the persistence length for polymers more complicated than mono-substituted vinyl polymers. The issue becomes complicated when chain secondary structures such as tacticity and helical coiling become important to chain conformation [14–19]. A direct measure of the persistence length using small-angle scattering remains the most robust approach to describing local chain conformations. A combination of the Kratky–Porod approach with modern scattering functions and an understanding of fractal scaling laws offer hope in describing both chain conformation as well as the statistical thermodynamics of these complicated systems [12]. For a detailed description of the use of small-angle scattering to quantify the persistence length the interested reader is referred to Ref. [3].
1.3 Coil structure and chain scaling transitions As mentioned above, for sizes on the order of the persistence unit the coil size follows the scaling law, l K n1 c
(4)
where c is the bond length and n is the number of bonds in a persistence unit. This indicates that the Kuhn unit [20] is on average a linear structure as can be verified with scattering measurements where the scattered intensity scales as I(q) Bq1 at high q. At larger sizes and smaller scattering vector q a different, steeper scaling behavior is observed for synthetic polymers. This regime reflects the distribution of Kuhn units in space along a curved path that follows either a self-avoiding or a random walk. For a self-avoiding walk (SAW) the coil end-to-end distance, R, scales with, RSAW n3=5 lK
(5)
where n is the number of Kuhn units of length lK. If self-avoidance is removed by screening of excluded volume the coil can take a Gaussian configuration where the coil size scales with: RGaussian n1=2 lK
(6)
Equation (6) is the result of a calculation of the root mean square (RMS) endto-end distance from the summation of Equation (2). Equation (5) cannot be
128
Gregory Beaucage and Amit S. Kulkarni
obtained by such a direct calculation since it involves non-random chain scaling due to long-range interactions. Equation (5) is obtained by considering a comparison between Equation (1) and the Boltzman distribution function for a system at thermal equilibrium, EðRÞ PB ðRÞ ¼ exp (7) kT which yields a function for the free energy of the Gaussian chain, E ¼ kT
3R2 2nl2K
(8)
For a chain with excluded volume the probability of the chain avoiding one segment of volume Vc is PEx(R) ¼ 1Vc/R3. The total number of combinations of two chain units is n(n1)/2!Bn2/2 so the total probability of exclusion is, 1 0 Vc n2 =2 2 n ln 1 3 Vc n2 Vc R @ A exp PEx ðRÞ ¼ 1 3 ¼ exp (9) 2 R 2R3 Through multiplication of this probability with the Gaussian function Equation (1), and by comparison with Equation (7), ! 3R2 n2 V c þ E ¼ kT (10) 2R3 2nl2K Equation (10) yields decidedly non-Gaussian behavior and the chain end-to-end distance probability function using Equation (10) in (7) cannot be analytically integrated for moments such as the RMS end-to-end distance. For this reason a different approach is used to define a preferred chain size for the SAW using a derivative rather than an integral. A probability function proportional to the probability of a chain starting at radius of 0 having an end in a spherical shell of a radius R from the center is given by, ! 3R2 n2 V c 2 WðRÞdR ¼ kR exp dR (11) 2R3 2nl2K This function displays a maximum at the preferred chain end-to-end distance R that can be found by setting the first derivative to 0, pffiffiffi n 5 n 3 R R 9 6 V c pffiffiffi ¼ n (12) 16 l3K Rn0 Rn0 where Rn0 is the maximum probability for the Gaussian function, !1=2 2nl2K n (13) R0 ¼ 3 Equation (12) can be simplified by considering large ðRn =Rn0 Þ so that ðRn =Rn0 Þ5 ðRn =Rn0 Þ3 to yield the scaling relationship, Rn lK n3=5 which is the expression for a SAW.
(14)
Chain Structure Characterization
129
In Equation (10), Vc represents a hard-core repulsion that is entropic in nature since it is linearly dependent on temperature in the expression for energy. Repulsion is generally associated with enthalpic interactions and we can consider the effect of an enthalpic interaction. Since Vc is associated with a single Kuhn unit we consider the average enthalpy of interaction per pair-wise interaction and the number of pair-wise interactions per Kuhn unit, ðPP þ SS Þ PS (15) 2 where ePP is the average polymer–polymer (PP) pair-wise interaction energy, eSS is the average solvent–solvent (SS) pair-wise interaction energy, and ePS is the average pair-wise interaction energy for polymer–solvent (PS). Each Kuhn unit has z pair-wise interactions, where z is the coordination number (on a cubic lattice for instance). To remove the kT dependence introduced by Equation (10) we write, D ¼
w¼
zD kT
(16)
and V c;enthalpic ¼ V c ð1 2wÞ
(17)
where the factor 2 is included since there is no redundancy in interactions in Equations (15) and (16) when used in Equation (10). The free energy for an isolated chain with enthalpic interactions can be written, ! 3R2 n2 V c ð1 2wÞ þ E ¼ kT (18) 2R3 2nl2K Equations (18) and (16) define a temperature where Gaussian behavior is observed (the phase separation temperature) where w ¼ 1/2 and thermal energy is just sufficient to break apart PP and SS interactions to form PS interactions. Equation (12) using (17) for Vc is called the Flory–Krigbaum equation. This expression indicates that only three states are possible for a polymer coil at thermal equilibrium: (i) (ii) (iii)
the normal condition in solution reflected by a SAW, a unique condition seen exactly at the phase separation temperature reflected by Gaussian scaling, and the collapsed state at temperatures below the phase separation temperature for an upper critical solution temperature (UCST) system.
For a chain at equilibrium no other states are possible! The SAW, Equations (14) and (18), is the normal condition for a polymer chain in solution and this can be easily verified by observation of the fractal scaling regime in neutron scattering measurements. Polymers generally have limited solubility and it is often possible to bring a polymer solution to the phase separation point thermally, either by cooling (e.g., polystyrene in cyclohexane, Figure 3 and Section 1.4) or by heating (e.g., poly(vinyl methyl ether) in water).
130
Gregory Beaucage and Amit S. Kulkarni
3000
Rg 2500
Radius (Å)
2000 Rh 1500
1000
500
0 20
30
40
50
60
Temperature (°C)
Figure 3 Radius of gyration, Rg, and hydrodynamic radius, Rh, versus temperature for polystyrene in cyclohexane. Vertical line indicates the phase separation temperature. Reprinted with permission from Sun et al. [21]. Copyright 1980, American Institute of Physics.
It has been found experimentally that chain scaling just at the phase separation temperature follows the Gaussian prediction of Equation (2). However, it is known that the overall coil size varies with temperature, which indicates that the three-state model is incomplete. It is possible to resolve the apparent discrepancy between an expanding coil size and fixed chain scaling by considering a size-dependent thermodynamics within the coil. This is possible for high polymers because the energy expression in Equation (18) depends on coil size through n. For example, the energy of a chain calculated using Equation (18) is different for a chain of 500 Kuhn units compared to a chain of 1,000 Kuhn units. However, a chain of 1,000 Kuhn units is composed of 2 chains of 500 units and many chains of smaller sizes. Smaller chains have less entropy from Equation (18) and would be expected to thermally phase separate first. For example, as temperature is dropped towards the phase separation temperature in a UCST system we observe that the coil decreases in size. The coil at the small sizes reaches a point of phase separation at a higher temperature than the coil at large sizes. Locally we observe three regimes of scaling: (i) linear persistence at smallest sizes, (ii) Gaussian at intermediate sizes, where there is insufficient entropy for miscibility, and (iii) expanded coil SAW at large sizes, where there is sufficient entropy for miscibility. The size scale for transition between the latter
Chain Structure Characterization
131
two sizes is termed the thermal (or thermic) blob. Coils can show a gradual change in size with cooling due to changes in this thermal blob size. The chain also follows only the three possible states (Gaussian, SAW, or collapsed). Once the entire coil has reached the miscibility limit the chain finally phase separates just after displaying true Gaussian scaling on cooling for a UCST system. The thermal blob has been verified using small-angle neutron scattering (SANS) [22]. The understanding that polymers display an ability to accommodate thermal changes through scaling transitions was a major development in theoretical physics with ramifications to other chain and network structures such as proteins, DNA, and elastomers. Similar scaling transitions on external perturbation are known for stress, tensile blob, and concentration, concentration blob, as well as other possible chain perturbations. Concentration is of particular importance since it allows an understanding of the progression from a good solvent to the melt with increasing concentration. This progression is also of a gradual type despite the required three discrete state prediction and we explore the possibility of a scaling transition within the coil to explain this behavior. In progressing from a dilute solution to a concentrated solution and to the melt state we expect miscibility to decrease and the coil to contract. For a coil in dilute solution the coil displays two sizes, the overall coil size or end-to-end distance and the Kuhn length. As concentration increases a point is reached where the concentration within a coil, n/R3, is matched by the solution, cn ¼ k n=R3 ¼ k n4=5
(19)
where the latter expression relied on Equation (14); c is known as the overlap concentration. At this point coil overlap occurs and we do not expect thermodynamic parameters to depend on the overall coil size but on a new size introduced due to the increasing concentration. We can consider a scaling transition to occur at a size scale x associated with the overall coil size R and the reduced concentration, c P x R n nð3þ4PÞ=5 (20) c The last equality is obtained by considering Equation (19). Since we know that the scaling transition size is not dependent on n above c, then P ¼ 3/4 and, c 3=4 xR n (21) c This concentration-dependent scaling, transition is known as the concentration blob. At large size scales the coil displays Gaussian scaling, while at small size scales the coil displays SAW scaling since the coil at sizes larger than the scaling transition exists in a melt-like state where interactions are screened. At the transition size SAW scaling is obeyed x ¼ lK nx3/5, so with Equation (21), nx is equal to (c/c)5/4, and with Gaussian scaling at large size scales, c 3=4 c 5=8 c 1=8 1=2 R ¼ x nx ¼ RF0 n ¼ R (22) F0 c cn cn RF0 is the Flory radius describing the coil size at concentrations below c.
132
Gregory Beaucage and Amit S. Kulkarni
Equation (22) has been confirmed by a variety of techniques including neutron scattering, dynamic light scattering, and osmotic pressured measurements [23]. As concentration increases the concentration blob decreases in size until the Kuhn length is reached and the coil displays concentrated or melt Gaussian structure. The coil accommodates concentrations between the overlap and concentrated through adjustment of the concentration blob size. A similar scaling transition has been proposed to account for the response of an isolated coil to tensile stress [24,25]. If a force is applied to a Gaussian coil Equation (8) can be used to calculate the response of the coil since at thermal equilibrium the applied force FBdE/dR so, F¼
dE 3kT ¼ R dR nl2K
(23)
which defines the spring constant for an isolated coil. For weak perturbations the end-to-end distance R is close to n1/2lK so FB3kT/Rt, where Rt is the tensile blob size. This can be rearranged to express a size dependent on the applied force F, 3kT (24) F Rt decreases in size for larger applied forces. Equation (24) describes a size scale governed by a balance between the thermal energy of the coil and the applied force. For sizes larger than this scaling transition the coil presents no resistance to the applied force and we expect a linear structure with RBnt Rt. For sizes smaller than this scaling transition we expect to observe the native scaling of the chain either Gaussian or SAW scaling. A similar behavior can be observed when straightening a kinked string, that is large scales straighten out earlier with increasing applied force compared to smaller features. For the tensile blob, thermal blob, and concentration blob we find that the coil accommodates external stress (thermal, concentration, or force) through a scaling transition that leads to two regimes of chain scaling. This directly impacts the free energy of the chain, the mechanical response, and the coil size. Rt ¼
1.4 Measures of coil size Rg and Rh Models of the polymer coil are based on the end-to-end distance, which is generally not directly available as a quantitative feature. Coils in dilute solution can be characterized in terms of the radius of gyration, Rg, which is a statistical measure of the distribution of mass about the center of gravity or in terms of the hydrodynamic radius, Rh, that is usually determined through the use of Stokes law and a measurement of a drag coefficient or friction factor, fdrag, for the coil, Fdrag ¼ f drag ucoil
and
f drag ¼ 6pRh Z0
(25)
where ucoil is the velocity of the coil, Z0 the viscosity of the pure solvent, and Fdrag the force associated with drag of a moving coil in a solvent. Under the
Chain Structure Characterization
133
assumption that the coil is non-draining (Kirkwood Reisman theory), Rh reflects the radius of a sphere enclosing the coil. There is no clear means to verify the non-draining assumption and generally Rh should be considered a value that scales with the end-to-end distance. The radius of gyration, however, has an analytic relationship to the coil end-to-end distance. R2g is expressed as, n 1X R2g ¼ ðri RG Þ2 (26) n i¼1 where RG is the center of mass, RG ¼
n 1X ri n j¼1
(27)
Combining Equations (26) and (27) yields, R2g ¼
n X n n X n n X n X 2 1 X 1 X i j l2 ¼ 1 ri rj ¼ i j l2K K 2 2 2 2n i¼1 j¼1 2n i¼1 j¼1 n i¼j j¼1
l2K ½z þ 2ðz 1Þ þ 3ðz 2Þ . . . ðz 1Þ2 þ z ð28Þ n2 where z ¼ n1. The last series can be obtained by constructing an n n matrix of i versus j with values of |ij| and recognizing that the matrix is symmetric about i ¼ j. The bracketed expression in Equation (28) can be rewritten, ¼
z X p¼1
z z X X zðz þ 1Þðz þ 2Þ n3 ffi z þ 1 p p ¼ ð z þ 1Þ p p2 ¼ 6 6 p¼1 p¼1
(29)
using N P
up ¼
u¼1
N pþ1 N p pnp1 þ þ pþ1 2 12
for po3
(30)
Using Equation (29) in (28), R2g ¼
2 R nl2K ¼ 6 6
(31)
Equation (31) applies to monodisperse systems. For polydisperse systems R2g reflects a high-order moment of the distribution, the ratio of the 8th to the 6th moment of the distribution in mean size. For this reason Rg will correlate with the largest sizes of a distribution. There are several advantages to Rg as a measure of size over the end-to-end distance. For branched, star and ring structures the end-to-end distance has no clear meaning while Rg retains its meaning. Further, Rg is directly measured in static scattering measurements so it maintains a direct link to experiment.
134
Gregory Beaucage and Amit S. Kulkarni
2. LOCAL STRUCTURE AND ITS RAMIFICATIONS 2.1 Tacticity Local chain structure is governed by chemical make-up, configuration, and conformation. Polymer chain conformation refers to the different orientations of the repeat units brought about by bond rotations. Configuration, however, cannot be changed by simple bond rotations, and refers to how the units add into the polymer sequentially during polymerization. An example of different polymer chain configurations is that brought about by head-to-head addition of repeat units as opposed to head-to-tail addition. In the case of vinyl polymers (–CHX–CH2–) the substituted carbon is usually designated as the head, and the unsubstituted methylene unit is designated as the tail. Tacticity in polymers (see also Section 3.4.2, Chapter 2): Polymers formed from substituted monomers, like vinyl polymers, display tacticity which has bearing on the final polymer properties like degree of crystallinity, crystalline phase structure, and melting temperatures as well as glass transition temperature for di-substituted vinyl polymers. Tacticity or handedness describes the stereochemical arrangement of a chain unit relative to other chain units. The smallest unit of tacticity is a diad composed of two mer units. The linkage point between two mer units along a single-bond carbon backbone chain can be made in two distinguishable ways as shown in Figure 4. In Figure 4(a), the position of the substituent R group can be either in the top or bottom location — two enantiomers. While the groups can rotate about the C–C bond this will not reverse the stereochemical arrangement as can be seen in Figure 4(b) in the Newman projection. This can more clearly be seen if one considers a walk along the polymer chain from the left P, over the C–C bond and then to the right P. On this walk the substituent group will either be to the right or to the left regardless of rotation of the C–C bond. In this case distinguishing the chiral state of the mer depends on the walker’s observation since the walker can H (R) H (R)
H P
P
P P
H (a)
R (H)
R (H )
H (b)
Figure 4 Sketch of two possible stereochemical arrangements for a chiral monomer. P represents the polymer chain, R represents a vinyl substitutent on a carbon, H represents hydrogen. (a) Linear sketch showing one conformation and two configurations (bracketed and unbracketed). The apex of bonds is a tetrahedrally bonded carbon atom (solid and dashed circles). (b) Newman projection of the same monomer showing the free rotation about the C–C bond.
Chain Structure Characterization
135
distinguish between right and left. In the absence of the walker the two states are not distinguishable. This is because handedness is only defined relative to the handedness of an observer. Free of an embedded observer a molecule can inherently define handedness by two neighboring chiral centers. For two chiral centers along a polymer chain a diad can identify two states, similar enantiomers or a meso diad (m) and dissimilar enantiomers or a racemic diad (r). In a meso diad a walker along the chain would find substituent groups both on the right side, for example, in the walk described above. There are two possible arrangements of meso diads (left–left or right–right) and two possible arrangements of racemic diads (right–left or left–right) so that an unbiased stereochemical arrangement would contain 50% meso diads. This could be one description of an atactic or non-tactic polymer. However, few properties of polymers are associated with diad tacticity since most properties are associated with longer groupings of mer units. For example, the stereochemistry of diads has little direct effect on the ability of long sequences of a chain to form a helix and to crystallize. Finally, there is no quantitative analytic technique to directly measure diad tacticity in polymers. The smallest unit that can be observed, by nuclear magnetic resonance (NMR), for instance, requires groupings of three mer units. This is because NMR relies on splitting of resonances associated with the distinguishing of different neighboring chiral groups. For a given mer unit two neighboring mer units can be equally observed leading to a group of 3 mer units. This triad can have one of three arrangements, mm (isotactic), rr (syndiotactic), or mr/rm (heterotactic). Since there are twice as many possible arrangements of heterotactic, a random mixture of triads would result in 25% isotactic, 25% syndiotactic, and 50% heterotactic triads. This could be an alternative definition of an atactic polymer. It should be noted that a polymer defined as atactic by diads could be 100% heterotactic or could have many other stereochemical arrangements of triads. Then there is a limited connection between tacticities as measured at different orders in going from lower to higher order (diads to triads). We can use statistics to predict the most likely triad arrangement associated with a given diad distribution. Higher-order tacticities are associated with only one lower-order distribution. Generally, we are interested in the highest possible order of tacticity since this governs the properties of a macromolecule. Highorder stereochemical arrangements do not have names associated with their states since a plethora of arrangements are possible. Generally, we speak of odd orders, 3 (triad), 5 (pentad), 7 (heptad), etc., due to the nature of the NMR measurement mentioned above.
2.1.1 Determination of tacticity (stereoregularity) The tacticity or distribution of asymmetric units in a polymer chain can be directly determined using NMR spectroscopy and infrared (IR) spectroscopy and has been studied for a variety of polymers. Figure 5(a) and 5(b) show the proton NMR spectra [26,27] and IR spectra [28,29], respectively, for the two stereoisomers of poly(methyl methacrylate) (PMMA), syndiotactic and isotactic PMMA. These two structures in a polymer like PMMA give rise to different signatures in both the techniques. In the case of the NMR spectra [26,27], the
136
Gregory Beaucage and Amit S. Kulkarni
(a)
(b)
r
6.40 τ
(a)
8.14
10.00
8.78 8.95 9.09
% ABSORBANCE
160
80 SYNDIOTACTIC PPMA
ISOTACTIC PMMA
0 3100 2800 1800 1650 1525 (b)
700 WAVENUMBERS cm-1
Figure 5 (a) Proton NMR spectra for syndiotactic (upper) and isotactic (lower) poly(methyl methacrylate). Reproduced from Sperling [27]. Copyright 2006, John Wiley & Sons, Inc. (b) IR spectra for syndiotactic and isotactic poly(methyl methacrylate). Reprinted with permission from O’Reilly and Mosher [28]. Copyright 1981, American Chemical Society.
Chain Structure Characterization
137
occurrence of a peak at 8.78 ppm chemical shift (tetramethylsilane peak at 10.00 ppm) as seen in the lower spectrum of Figure 5(a) corresponds to the meso placement of the alpha methyl units and hence represents an isotactic PMMA spectrum. The upper spectrum in Figure 5(a) with a peak at chemical shift of 9.09 ppm corresponds to the racemic placement of the alpha methyl units and hence a syndiotactic PMMA spectrum. The sensitivity of the chemical shift of the alpha methyl protons is accepted to be a fundamental feature reflecting the stereochemical configuration of PMMA. These specific shifts arise from triad sequences in PMMA. Higher-order sequences can be detected in different polymers by going to higher magnetic fields. From the IR spectra shown in Figure 5(b) [28,29], peak assignments can be made for the two configurational isomers of PMMA and are given in Table 1. Some basic aspects of the selection rules for IR spectroscopy and Raman scattering for the detection and characterization of stereoregularity for such polymers are given in Ref. [30]. Similar studies have been conducted on poly(vinyl chloride) (PVC) to assign different IR signatures obtained from different stereo-configurational isomers. The sensitivity of the nC–Cl bond on the stereochemical environment has been utilized using IR spectroscopy. The characteristic vibrations of the nC–Cl bonds are inherently tied in to the configuration as well as the conformation of the
Table 1 [28]
IR peak assignments (cm1) for isotactic and syndiotactic poly(methyl methacrylate)
Isotactic
Syndiotactic
Peak assignment
1,465 1,190 996 950 759
1,450 1,190 998 967 749
d(CH2), da(CH3-O) Skeletal gr(CH3-O) gr(a-CH3) g(CH3) and skeletal
d and g, deformation modes; da , antisymmetric; gr rocking.
Table 2 IR peak assignments for poly(vinyl chloride) based on polymer conformation and configuration [31] Peak (cm1)
Conformational assignment
Configuration
602 619 639 651 676 697
TTTT long sequences TTT short sequences TTTT long sequences TTTG syndiotactic TGuGu syndiotactic TGTG isotactic
Syndiotactic Syndiotactic Syndiotactic Syndiotactic Syndiotactic Isotactic
T, trans; G, gauche (Gu represents a gauche configuration where the rotation about the bond is in the opposite direction to G).
138
Gregory Beaucage and Amit S. Kulkarni
polymer. The effects of configuration and conformation on the IR peak assignments for PVC are given in Table 2 [29,31]. The commercialization of polypropylene (PP) had been revitalized with the advent of metallocene and vanadium-based catalyst systems, which result in highly stereoregular isotactic and syndiotactic PP, respectively [32]. The advent of these catalyst systems has enabled the synthesis of these PP isomers with enhanced physical properties [33] and applications [34]. Recently Rojo et al. [32] have devised a rheology-based technique to differentiate between stereoisomers of PP. The procedure involves plotting the loss tangent (d) as a function of the complex modulus G as shown in Figure 6 [32]. Differentiating between syndiotactic and isotactic PPs is based on the higher values of Newtonian viscosities, terminal relaxation times, and activation energies for flow for syndiotactic PP samples [32]. Positive identification and differentiation of isomers is possible by plots like the one shown in Figure 6, i.e., plots of loss tangent values versus complex modulus [32]. A consequence of tacticity/stereoregularity is the production of regular helical coiling of the polymer chain. Helical coiling is a secondary structure for synthetic polymers associated with the primary structure of the tactic sequence. Using IR spectroscopy, it has been possible to assign some unique bands to
90
80
70
δ (˚)
60
50 sPP 1 sPP 2 sPP 3 Met-iPP 1 Met-iPP 2 Maxwell model for Met-iPP 1 Maxwell model for sPP 1
40
30
20 100
101
102
103
104
105
106
G* (Pa)
Figure 6 Loss tangent (d) plotted as a function of complex modulus G for a series of syndiotactic and isotactic polypropylene. Reproduced with permission from Rojo et al. [32]. Copyright Wiley-VCH Verlag GmbH & Co. KgaA. iPP, isotactic PP; sPP, syndiotactic PP; Met-iPP, metallocene-catalyzed PP (see Ref. [32] for full details).
Chain Structure Characterization
139
tacticity in polymers with helical chain structure. These bands are classified as the helix bands and regularity bands [30]. The helix band not only depends on the nature of tacticity, but on the sequence length of the stereo-configuration. Thus additional microstructural information can be obtained from such IR studies. The values of such absorption bands for some common polymers like PP and polystyrene can be readily found in texts on this subject [30].
2.2 Branching The presence of branches along the main chain of a polymer molecule significantly alters the static and dynamic properties of the polymer [35]. The presence of structural branching is not limited to commercial polymeric materials like polyolefins, but plays an important role in altering the properties of a broad spectrum of materials, which can be classified as nano-particulate ceramic aggregates, polymeric networks and gels. Branch content and nature has a strong influence over structure–property relationships of these materials. For example, the presence of branch content dictates the crystallization behavior [35] of commercial polyolefins and copolymers, the mechanical properties of crosslinked macromolecules, and the nature and extent of reinforcement obtained from aggregated inorganic materials like silica and titania [36–41] when dispersed in an organic polymeric matrix. The need of quantifying branch content in such materials is of vital significance not only to predict the structure–property relationships dictating characteristic material performance in end-applications, but also to gain a better understanding of the underlying thermodynamic and kinetic processes [42–52] governing the synthesis of these materials. Estimating branch content through the development of novel analytical approaches has been a quest for materials scientists for well over five decades. One of the very first approaches to estimate branch content in polymers was using size exclusion chromatography (SEC) (vide infra). The solution properties of a branched polymer molecule differ vastly from that of its linear analogue. The vital difference between a branched and a linear polymer molecule is in the size that they exhibit in solution. SEC essentially fractionates a polydisperse polymer sample into monodisperse fractions based on their molecular size in solution. Hence estimating branch content for polydisperse polymers from SEC is based on this disparity of molecular sizes of branched and linear polymer molecules. NMR spectroscopy has been a very effective tool to estimate branch content in polymers on a quantitative basis. It has the added advantage of being able to discern the branch lengths up to a certain degree. 13C-NMR spectroscopy has been mostly used to carry out such an analysis and depends on the calculations of the chemical shifts arising due to the presence of structural branching. Favorable rheological properties are an essential requirement for the commercialization of polyolefins like polyethylene. The ease of processability of the polymer melt, obtained through modifications in the microstructural features, is as important as the end use mechanical properties of these polymers. Presence of long-chain as well as short-chain branching, LCB and SCB, respectively, more or less dictates the rheological behavior of most commercial
140
Gregory Beaucage and Amit S. Kulkarni
polyolefins. Inherently, various studies have been conducted over the years linking the melt behavior to the underlying polymer chain microstructure. As already stated, apart from the importance of estimating branch content for determining structure–property relationships, the quest to ascertain the branch content information also has some motivation for enhancing our understanding of some fundamental phenomenon, e.g., phase separation [42–51] between polyolefin blends of high-density polyethylene (HDPE) and linear low-density polyethylenes (LLDPEs) has been reported in literature, where the amount of branches in the linear low-density material govern the occurrence of micro-phase separation. Similarly, even crosslinked materials like poly(dimethylsiloxane) (PDMS) [52] exhibit phase separation driven by a disparity in the topological features of the two phases. The presence of short-chain branching and its estimation has been fundamental to discerning the crystallization kinetics and mechanisms in commercial polyolefins like ethylene-alkene copolymers.
2.2.1 Types of branching in polymers The nature and amount of branch content in macromolecular systems is diverse and plays a fundamental role in their characteristic behavior [53–57] (see also Chapter 2). Apart from molecular weight and molecular weight distributions (MWDs), the nature of branching leading to different topological features can be considered as one the most fundamental features dictating the properties of macromolecules. The classification of many systems is based on the nature of their topological features. Branching in commercial polyolefins is classified as long- or short-chain branching. The presence of either long- or short-chain branching has a unique effect on the properties of these polymers. Long-chainbranched polymers are usually classified to be described as randomly branched polymers. Short-chain branching in polymers leads to structures usually defined as ladder-architecture. Graft-copolymers, where short branches of one polymer are present on the backbone of a second polymer are a special case of ladder polymers. Multi-arm star polymers have also been extensively studied for their unique properties. Dendrimers and hyperbranched polymers (HBPs) represent another class of highly branched polymers. HBPs are similar in structure to dendrimers, but lack a central core from which growth occurs through hierarchical levels as in dendrimers, and are usually synthesized in a one step process. The schematic representation of these various branched architectures is shown in Figure 7. The crystallization kinetics of commercial polyolefins is to a large extent determined by the chain microstructure [58–60]. The kinetics and the regime [60] of the crystallization process determine not only the crystalline content, but also the structure of the interfaces of the polymer crystals (see also Chapter 7). This has a direct bearing on the mechanical properties like the modulus, toughness, and other end use properties of the polymer in fabricated items such as impact resistance and tear resistance. Such structure–property relationships are particularly important for polymers with high commercial importance in terms of the shear tonnage of polymer produced globally, like polyethylene and polyethylene-based copolymers. It is seen that in the case of LLDPE, which is
Chain Structure Characterization
141
Figure 7 Schematic representation of different types of branched structures as discussed in the text.
essentially a copolymer of ethylene and 1-alkenes like hexene and octene, giving rise to butyl and hexyl branches, respectively, on a polyethylene backbone, apart from the amount of 1-alkene comonomer, branch content, and small-chain branch length, the primary modulator controlling the crystallization behavior is the sequence length distribution arising from these short-chain branches [58,59,61]. Hence, characterizing the sequence length distribution using spectroscopic techniques is as important as quantifying the short-chain branch content. HBPs [62–64] represent a special class of polymers with a unique set of properties. The development of synthesis chemistries of these materials has been fueled by the numerous potential applications such materials are expected to have. Characterization of the chain structure of such topologically unique materials is critical to understanding and predicting their properties.
2.2.2 Size exclusion chromatography SEC (also known as gel permeation chromatography (GPC)) is routinely used to characterize the MWD in a polydisperse polymer sample (see also Chapter 6). Fractions with different molecular weights are separated by passing a solution of the polymer through a series of columns on the basis of their hydrodynamic volume [65–68], which is the product of the intrinsic viscosity (limiting viscosity, [Z]) and the viscosity average molecular weight M v . The universal calibration curve, obtained from standard polymer samples of known MWD is used to compare with the elution profile for the given polymer sample. Most modern SEC setups are equipped with a triple detection system. They consist of an inline viscometer detector (VD), a refractive index detector (RID), and a light scattering detector (LS). The VD can be used to continuously monitor the intrinsic viscosity [66,67] of the eluting fractions, with the concentration of the given fractions being ascertained by using the RID.
142
Gregory Beaucage and Amit S. Kulkarni
Figure 8 Difference in the size of a branched polymer molecule (b) compared to its linear analogue (a) of the same molecular weight in solution.
Though SEC is used to characterize the MWD in a polymer sample, it separates a polydisperse polymer sample on the basis of the hydrodynamic size of different fractions and not their molecular weights [66,67]. Hence a branched polymer molecule and a linear polymer molecule of equal size cannot be differentiated by a SEC technique, since both of these would elute out at the same time. For a branched polymer molecule and its linear analogue (having the same molecular weight as the branched molecule) the radius of gyration of the linear polymer will be greater [66] than that of the branched molecule, as can be seen in the schematic shown in Figure 8. In their seminal work in 1949, Zimm and Stockmayer [69] defined the ratio of the mean square radii of gyration of a branched and a linear polymer of equal molecular weight as the parameter g and is related to the parameter gu, which is the ratio of the intrinsic viscosities of a branched and a linear polymer [65–69]. D E R2g where g ¼ D Eb ; R2g
g0 ¼ ge and g0 ¼
(32)
½Zb ½Zl
l
where e is a scaling constant, hR2g i the mean square radius of gyration, [Z] the intrinsic viscosity, and the subscripts b and l refer to the branched and linear polymer, respectively. The intrinsic viscosity and molecular weight measured in a SEC experiment correspond to the actual branched molecule being run through the column. The Mark–Houwink equation can be used to calculate the intrinsic viscosity of the linear analogue with the same molecular weight as the branched polymer being run through the SEC and is given by, ½Zl ¼ KMa
(33)
where K and a are constants for a given polymer–solvent pair. This analytical procedure results in the estimation of the parameter g. The Zimm–Stockmayer relationship (Equation (34) [69]) is used to estimate the branch content. The Zimm–Stockmayer relationship is specific to the nature of the branch content. It requires a prior knowledge of the functionality of the branch point in the main chain, as well as the dispersion in the branch lengths (whether the branch lengths are monodisperse or random) [66–68]. For polydisperse branch lengths
Chain Structure Characterization
with tri-functional branch points, g is given as [66–69], ( ) 6 1 ð2 þ nw Þ1=2 ð2 þ nw Þ1=2 þ ðnw Þ1=2 ln 1 g3 w ¼ nw 2 ðnw Þ1=2 ð2 þ nw Þ1=2 ðnw Þ1=2
143
(34)
where the subscripts 3 and w indicate tri-functional branch points with polydisperse branch lengths and nw is the weight average number of branches per molecule. The parameter nw then needs to be converted to express branch content in conventional terms of number of branches per 1,000 backbone carbon atoms, and is given as [67] (for polyethylene), LCB nw ¼ ð14; 000Þ 1; 000C M
(35)
where M is the molecular weight, and 14,000 corresponds to the molecular weight of 1,000 repeat units of a –(CH2)– molecule. In spite of the analytical nature of SEC to estimate branch content in polymers, it represents a relative/secondary technique to those based on indirect calculations of iterative solutions of Equations (32) and (34) [68]. There is a disparity in the experimental conditions and the theoretical assumptions involved in estimating branch content. SEC experiments are carried out in good solvents (good solvent scaling for the polymer molecules) whereas the Zimm– Stockmeyer relationships were derived for theta solution conditions (e ¼ 1/2), which imply a Gaussian scaling. The effect of these assumptions on different branched polymer systems cannot be estimated. The sensitivity of the detectors used in a SEC experiment dictate the accuracy of the obtained results (Figure 9). Molecular weight sensitive detectors like VD and LS show poor response in the low-molecular weight tail of the chromatogram, whereas concentration sensitive detectors like differential refractive index detectors (DRI) have a poor response in the high-molecular weight slice of the raw data [70]. Multi-detector configurations (triple detector) seem to have overcome some of these difficulties; though it has led to an increased complexity in the experimental procedures. The disparity in the intrinsic viscosity of a branched polymer compared to a linear analogue is used to estimate branch content by using SEC. The presence of short-chain branching does not significantly alter the intrinsic viscosity of a polymer molecule. The reduction in [Z] due to short-chain branching is estimated to be only 0.01 times [62] that due to long-chain branches. Hence the sensitivity of SEC to estimate short-chain branching is limited, and only high levels of long-chain branching can be estimated effectively, where comparative data is lacking as discussed below in the section concerning NMR spectroscopy.
2.2.3 Nuclear magnetic resonance spectroscopy NMR spectroscopy can be utilized to obtain branch content information for commercial polymers in a direct quantitative manner. Polyethylene and PVC are the two commercial polymers that have been studied extensively for branch content determination by this technique [71–75]. Obtaining branch content information from such polymers has been dealt with, by using high-resolution
144
Gregory Beaucage and Amit S. Kulkarni
Figure 9 SEC: Response versus retention volume for (a) RID, (b) VD, and (c) LS detector for the same sample. Reproduced from Beer et al. [70]. Copyright 1999 John Wiley & Sons, Inc. Reprinted with permission of Wiley-Liss, Inc., a subsidiary of John Wiley & Sons, Inc.
Chain Structure Characterization
145
13
C-NMR spectroscopy. This technique involves assignment of the specific shifts in the resonance peaks arising due to a branch point in a carbon backbone chain. Conventionally, these resonance shifts have been calculated for up to five carbon atoms from the branch point [76]. Such an analysis results in the direct estimation of the branching density in a polymer sample like polyethylene. In the case of PVC, the approach is not as simple as for the case of polyethylene, with complications arising due to the stereochemical isomerization in structure due to the presence of the chlorine side groups along the main chain [70]. This necessitates the removal of the chlorine atoms via a reductive de-chlorination process using either lithium aluminum hydride [77] or tri-butyl tin hydride [78]. Once the de-chlorination step is complete, the branch content in PVC can be obtained similar to polyethylene using high-resolution 13C-NMR spectroscopy. The technique of obtaining the shifts in the NMR resonance peaks due to branch points was developed by Grant and Paul [79], also, for example, described in Refs. [29,80], and shall be briefly discussed below.
Grant and Paul Chemical Shifts. The technique of obtaining branch content information from NMR for polymers utilizes an empirical relationship given by Grant and Paul [29,79,80]. The Grant and Paul empirical relationship [29,79,80] can be used to calculate the values of the chemical shifts for carbon atoms in the vicinity of a branch point in a hydrocarbon polymer. The empirical relationship was obtained from NMR studies on alkanes. The chemical shift of any carbon atom in a 13CNMR can be decomposed as a sum of contributions from its nearest five neighboring carbon atoms. The value of the chemical shift for any carbon atom C, is given as, Chemical Shift ¼ 2ða þ b þ g þ d þ Þ þ C (36) where a, b, g, d, and e are called Grant and Paul parameters, and C is a constant, the values are outlined in Table 3 [29,80]. This empirical relationship cannot be used without accounting for some correction terms, which take into account the molecular geometry of the bonded neighbors. This is especially essential when calculating the chemical shift of a branch point carbon atom. These correction terms were given by Grant and Paul to be as follows [29,80]. In Table 4, 31, 21, and 11 represent tertiary, secondary, and primary carbon atom, respectively (Figure 10), and 31(21) represents correction for a tertiary carbon bonded to a secondary, as in a methine group to a methylene. In a study conducted Table 3
Grant and Paul parameters obtained from alkanes [80]
Grant and Paul parameters
Shift (ppm)
a b g d e C
8.61 9.78 2.88 0.37 0.06 1.87
146
Gregory Beaucage and Amit S. Kulkarni
Table 4
Correction values for branched polymers [80] Shift (ppm)
31(21) 21(31) 11(31)
2.65 2.45 1.40
Figure 10 Schematic representation of tertiary (31), secondary (21), and primary (11) C atoms.
by Randall [81], the temperature dependence of these correction terms was evaluated. This resulted in slight modifications of the values of the corrections terms. The temperature dependence of these correction parameters were determined by 13C-NMR on highly branched hydrogenated polybutadiene [81]. Using this technique, high-resolution NMR can be utilized not only to obtain branch content information in terms of the branching density in the polymer molecule, but also to estimate the length of the branches. Herein lies a limitation of using NMR to estimate branch content information. The Grant and Paul empirical relationship results in the estimation of specific peak shifts for a branch point carbon atom with different branch lengths provided the branches are smaller than six carbon atoms long, beyond which the branch would be assigned as a long-chain branch by NMR. In a polymer like polyethylene, a branch just about greater than six carbon atoms, does not constitute a long-chain branch, when it’s manifestation on the rheological properties are concerned. It is more apt to define a branch as being a long-chain branch, depending on the number of entanglement units present. Recent studies by Liu et al. [82] have expanded the scope of using NMR to detect branch lengths up to 10 carbon atoms. Liu et al. [82] were able to assign chemical shits values to carbon atoms in a branch longer than six carbons by using ultra-high frequency 13C-NMR (188.6 MHz). NMR remains a very useful technique to estimate branch content in hydrocarbon polymers and constitutes a direct quantitative approach. However, using NMR in quantifying branch content has a drawback in that the results for the branch content obtained will always overestimate long-chain branching, i.e., branches longer than about six carbons. Hence, the sensitivity of NMR to determine branch content is limited to high levels of short-chain branching. But
Chain Structure Characterization
147
NMR is an effective tool for the determination of total number of branch sites, nbr, in a polymer chain.
2.2.4 Rheology The rheological behavior of polymer melts is a critical aspect determining the processing parameters of most melt-processed polymers like polyolefins. The presence of structural long-chain branching profoundly alters the behavior of polymer melts, even at extremely low levels. While NMR remains an effective means of quantitatively estimating the number of branch sites in a polymer molecule, its utility in characterizing the feature important to rheological behavior, the volumetric contribution of long-chain branching, is limited. The volumetric contribution of long-chain branches to a polymer molecule can be expressed as [83], zp jbr ¼ (37) z where p is the occupied volume or the mass of a minimum (conducting) path across the polymer (the main chain backbone) and z is the occupied volume or mass of the entire branched structure. Since this feature is critical to rheology of polymers, and its manifestations apparent at even very low levels of long-chain branching, it is natural that numerous studies have been reported in the literature that use rheology to quantify long-chain branching. The presence of long-chain branching has a profound effect on the rheological properties of commercial polymers [84–90], especially the new generation of metallocene catalyzed polyethylenes [91–98]. As was discussed in the previous section on NMR, the definition of what constitutes a long-chain branch is more apt, if it is based on the presence of number of units of entanglements that the branch length represents. Studies have shown that long-chain branches of the order of 2–3 times [53–57] the entanglement molecular weight, Me, strongly affect rheological behavior. It is generally accepted that it is the linear viscoelastic properties of branched polymers as opposed to the non-linear viscoelastic properties that can provide optimum quantification of LCB [84,99], since the disparity in the non-linear viscoelastic properties could be assigned to both, branching as well as the higher molecular weight fractions in a generally polydisperse commercial polymer, and can be equally due to high-molecular weight fractions or branching [84,99]. Covering the enormous volume of the number of rheological approaches to quantify long-chain branching reported in the literature is beyond the scope of this chapter, and hence, only a few key studies shall be discussed in this section. Lai et al. [100] proposed the use of the Dow Rheology Index (DRI) as an indicator for comparing branching level in industrial polymers. For a linear polymer molecule, like unbranched polyethylene, the viscosity of the polymer as a function of the applied shear rate is given by the Cross equation [84,100], Z 0 n Z g ¼ (38) 1 þ lg
148
Gregory Beaucage and Amit S. Kulkarni
where Z0 is the zero shear rate viscosity, g the shear rate, and l the characteristic time given as 3.65 105 l ¼ Z0. The DRI given by Lai et al. [100] is expressed as,
3:65 105 l=Z0 1 (39) DRI 10 In the absence of long-chain branching, the DRI is expected to be zero and would have positive values for polymers with long-chain branching. It should be noted that the application of the DRI is limited to polymers with a narrow MWD, Mw/Mno2, since it cannot delineate the differences arising from polydispersity and long-chain branching. Shroff and Mavridis [85] proposed the long-chain branching index (LCBI). Though the DRI proposed by Lai et al. [100] estimated differences in branch content between different polymer samples, its restricted applicability to narrow dispersion polymers was a serious limitation. The LCBI [85] was developed to overcome this shortcoming of the DRI. LCBI essentially derives from the theory of branched polymer molecules as given by Zimm and Stockmayer [69]. The primary assumption involved in the approach taken by Shroff and Mavridis [85,101] is that, at very low levels of long-chain branching, the polymer molecules can be considered to be essentially linear. Hence for such a polymer, the Zimm–Stockmayer parameter g [69], is equal to 1. For the calculation of the LCBI, one needs to experimentally measure the zero shear rate viscosity of the polymer sample. The presence of long-chain branches enhances the zero shear rate viscosity [85], and the LCBI is essentially a measure of the amplification in the zero shear rate viscosity due to long branches. The LCBI is given as, ! 1=a Z0 3 1=a3 LCBI ¼ 1 (40) k3 ½Z where Z0 is the zero shear viscosity and [Z] is the intrinsic viscosity and the constants k3 and a3 are obtained by fitting an equation of the type [85], Z0 ¼ k3 ½ZaL3
(41)
where [Z]L is the intrinsic viscosity of a linear polymer. The first term on the right-hand side of Equation (40) is the viscosity enhancement factor due to long-chain branches. LCBI is zero for a linear polymer, and would have positive values in the presence of long-chain branching [85]. Some attempts have been made to correlate rheological behavior with NMR data. One such technique is based on the work of Wood-Adams and Dealy [102], who proposed obtaining the MWD from complex viscosity data, and called it viscosity MWD. In this technique, the weight fraction as a function of reduced molecular weight m (m ¼ M/Mw) is plotted against m to get the MWD. Their observation that long-chain branching caused departures in the viscosity MWD as compared to MWD obtained from GPC measurements [84], led to the development of a technique to estimate branch content with quantitative analysis based on NMR studies. They proposed a routine for quantifying the branch
149
Chain Structure Characterization
content based on this observation, using a factor called the peak ratio, which is the ratio between the m value of the peaks in the distributions obtained by the two techniques, given as [84], peak ratio ¼
GPC MWD peak viscosity MWD peak
(42)
Figure 11 shows such a deviation in the peaks of the MWD obtained from the two techniques [84]. The LCB content for the polyethylene sample shown in Figure 11 was estimated to be 0.8/104 C by NMR. Wood-Adams and Dealy [84] obtained a correlation between the shift values, and the branch content from NMR measurements, given as, LCB ¼ 0; for PRo1 104 C LCB ¼ 1:125 logðPRÞ; for PR 1 ð43Þ 104 C where PR is the peak ratio, defined in Equation (42). As can be seen, most rheological techniques involve estimating the branch content by developing semi-empirical relationships that correlate the presence of long-chain branched structure to the derived rheological properties of such structures. Determination of branch content using dynamic rheology has its share of experimental drawbacks. The frequency limitations of most dynamic rheometers, means that dynamic measurements cannot be carried out in the frequency range of interest. This means that data must be extrapolated by means of viscosity models or using the time–temperature superposition. Simple viscosity models cannot appreciate the rheological complexities of a long-chain branched structure. Secondly, long-chain branching is a thermorheologically complex 1.2 1
w(log m)
0.8 0.6 0.4 0.2 0 0.001
0.01
1
0.1
10
100
m
Figure 11 Molecular weight distribution obtained from viscosity (o) and GPC (solid curve) measurements from the studies of Wood-Adams and Dealy [84]. Reprinted with permission from Wood-Adams and Dealy [84]. Copyright 2000, American Chemical Society.
150
Gregory Beaucage and Amit S. Kulkarni
structure [103,104] meaning that the simple time–temperature superposition principle used often to extrapolate rheological data need not be valid.
2.2.5 Small-angle scattering In a new analytical approach developed by Beaucage [83] and Kulkarni and Beaucage [105], branch content information and some fundamental parameters associated with the topology of a branched system can be estimated from smallangle scattering (X-ray or neutron) data. This technique can be applied to scattering data from long-chain-branched polymers, under some assumptions, since this analytical approach was primarily developed for non-thermodynamically stabilized structures like nano-particulate aggregates. Small-angle scattering from an aggregated system can be described in terms of local scattering laws like the Guinier’s law [83,105–107]: ! q2 R2g IðqÞ ¼ G exp (44) 3 where I(q) is the scattered intensity, q ¼ 4psin(y/2)/l, y the scattering angle and l the wavelength of radiation, and R2g the coil or aggregate radius of gyration and G is defined as N p n2p where Np is the number of polymer coils in given volume and np is a contrast factor equal to the electron density difference between the polymer coil and the solvent for X-ray scattering; and the power law [83,105–107] IðqÞ ¼ Bf qdf
(45)
where Bf is the power-law prefactor, taking account of local features like size and surface/mass scaling. Since these local laws are limited to describing features smaller than the overall aggregate size, they cannot independently describe overall structural features like branching and topology [83]. Thus, small-angle scattering would prove to be ineffective to estimate the branching characteristics of a polymer or an aggregated nano-particulate material. Beaucage [83] showed that on combination of the information obtained from different local laws, a different picture emerges. The basis of the analytical approach proposed by Beaucage [83] is the assumption of any branched systems to be composed of monodisperse primary particles aggregating to form the overall branched structure. Such a description can be considered to be applicable to branched polymers as well as nano-particulate ceramic aggregates, e.g., by considering the primary particles to be the Kuhn step in polymers, or the smallest individual particle in a ceramic aggregate. Further, such a structure could be considered to be linear or branched, as shown in Figure 12 [83]. The number of primary particles in the backbone chain, p, shown in Figure 12b represents the minimum path through the aggregate. A scaling relationship between the degree of aggregation z, the minimum path p, and the overall structural size R2 and size of the primary particle R1 can be given as [83,108–110], df R2 (46) pc ¼ z ¼ R1
Chain Structure Characterization
p
151
dmin
R2
R1
a)
b)
Figure 12 (a) Branched chain aggregate, (b) Branched chain aggregate; decomposed into the minimum path, p, and the branches [83]. Reprinted with permission from Beaucage [83]. Copyright 2004, American Physical Society. (See Color Plate Section at the end of this book.)
where c is known as the connectivity dimension, which is equal to 1 for a linear chain and df for regular objects (rod, disk, or sphere). A second scaling relationship between the above terms could be expressed in terms of the minimum dimension dmin [108,109] as, dmin R2 p¼ R1 df c¼ ð47Þ dmin where dmin represents the mass-fractal dimension of the minimum path (Figure 12b). These parameters, which describe the topology of a branched structure are determined from a static scattering experiment, and the branch content can be calculated in terms of fraction of material occupied in the branches and is given as [83], dmin df zp R2 1 ¼ 1 zc1 ¼ 1 jbr ¼ (48) z R1 which can be readily obtained from Equations (46) and (47). The parameter dmin could be calculated from the modified power-law prefactor equation to account for branched structures and expressing it as [83], G2 dmin df G Bf ¼ (49) df 2 Rg2 where G2 is the Guinier prefactor for the aggregate, Rg2 the aggregate radius of gyration, df the mass-fractal dimension and dmin is defined in Equation (47). Since all parameters in Equation (48), except dmin, are determined using Equations (44) and (45), Equation (49) can yield dmin, c (Equation (47)), and jbr (since z ¼ G2/G1
152
Gregory Beaucage and Amit S. Kulkarni
Figure 13 Branch fraction as a function of z and c [83]. The figure shows an estimate of the optimum range of branch content determination. Reprinted with permission from Beaucage [83]. Copyright 2004, American Physical Society.
where the subscripts 1 and 2 refer to the primary and aggregate structures fit with Equation (44)). Figure 13 [83] shows the sensitivity of the branch content calculated from such a measurement. This estimation should be good in the range of interest for most commercial long-chain-branched polymers (low c, high z) as well as ceramic aggregates. Beaucage [83] showed that it could be possible to get branching information for polymers using this approach. In Figure 14, where neutron scattering data for branched polystyrene is fit to the unified equation [83,107,110–112], it was shown that it is possible to calculate the parameters dmin and c, from such a fit [83]. These model branched polystyrene samples were synthesized by using divinyl benzene (10%) as a comonomer, to obtain controlled levels of branching but where the placement is random. Though such an approach would give an estimate of the branch fraction jbr, in terms of the volume fraction occupied by branches, it lacks information about the number of branch sites in the polymer. Thus, it would be necessary to use such a technique as a complementary approach with other techniques, like NMR, to get a complete picture of branch content. Development of mathematical analysis of scattering data to estimate size distributions in the structure can provide additional information about the
Chain Structure Characterization
153
Figure 14 Neutron scattering data from branched polystyrene fit to the unified equation [83]. Reprinted with permission from Beaucage [83]. Copyright 2004, American Physical Society. (Both the branched PS fractions were synthesized using divinyl benzene as a comonomer. Fraction F2 has a weight average molar mass of 18 108 g/mol and fraction F5 has a weight average molar mass of 2.0 108 g/mol, see Ref. 147.)
overall structure of the polydisperse branched species. Thus, scattering also offers the potential to describe the distribution in branch lengths through recent application of techniques such as the maximum entropy method [110,113–120].
2.3 Crystallization The presence of short-chain branching obtained by incorporating a-olefins like 1-hexene and 1-octene as co-monomers during polymerization of ethylene have a huge impact on its crystallization behavior [58,59,61]. These ethylene-a-olefin copolymers comprise what are known as LLDPEs. The development of the linear low-density class of polyethylenes has been critical in enhancing the processing characteristics of this polymer. LLDPEs have been synthesized by both, homogeneous metallocene catalysts as well as the heterogeneous Ziegler-Natta
154
Gregory Beaucage and Amit S. Kulkarni
type of catalysts [61]. This section deals with the effects of short-chain branching in such systems on the crystallization behavior of such polymers. (Characterization of the crystalline phase is considered by Alamo in Chapter 7 of this book.) The effect of short-chain branching, the placement of short-chain branching in terms of both, inter and intra-chain heterogeneity and the molecular weight of these polymers dictate the crystallization behavior, and hence play a vital role in the processing as well as the end use properties that can be obtained from such copolymers. The determination of sequence length distribution, which happens to be a ‘‘grey area’’ in this field, also shall be briefly discussed in terms of its importance and a new analytical technique published in a recent paper that makes an attempt to obtain the sequence length distribution quantitatively.
2.3.1 Effect of molecular structure on crystallization The presence of short-chain branches on the backbone of a flexible polymer like polyethylene has a complex effect on the crystallization process. This is in some part due to a general lack of understanding of how branched moieties affect the crystallization process [58]. It is widely believed that short-chain branches act as defects along the polymer chain and are excluded from the crystals, especially in the secondary nucleation step [58,59]. The process of secondary nucleation occurs by placing one stem of the polymer chain on the face of a crystal, which then facilitates the growth through spreading which would be energetically more feasible than the secondary nucleation step. The schematic shown in Figure 15 depicts this process, with i being the rate of secondary nucleation and g is the rate of surface spreading. The values of these two parameters decide the regime in which the crystallization process is occurring [58–61]. Before discussing the effect of short-chain branching on the kinetics of crystallization process, it is necessary to revisit the theory of secondary nucleation and the concept of regimes as given by Lauritzen and Hoffmann
b L
σe
g a
i σ
Figure 15 Schematic representing the secondary nucleation process and growth at the crystal face by spreading. The rates of these two processes are i and g, respectively. (See Color Plate Section at the end of this book.)
Chain Structure Characterization
155
[60]. Secondary nucleation is essentially a crystal growth process. Secondary nucleation occurs by the deposition of a stem of the polymer molecule on a preexisting crystal-face as shown in Figure 15. The overall rate of this process is given by the following expression [58], Kg Un G ¼ G0 exp exp (50) RðT T 1 Þ fTDT where, the first exponential contains terms related to diffusion and transport, and [58] Kg ¼
nbsse T 0m kDH f
(51)
In Ref. [58] these terms are defined as: G is the linear growth rate, U the activation energy for transport of the segments to the crystallization site, R the gas constant, T the crystallization temperature, and TN the temperature at which all motions associated with viscous flow cease, defined as Tg 201C. DT is the undercooling, T0m 2T. Kg is defined as Kg ¼ nbaae T 0m =DH 0f k where n is 4 for regimes I and III and 2 for regime II (see below). f is a correction factor used to compensate for changes in Dh0f with temperature at high undercoolings, defined as f ¼ 2T=ðT þ T 0m Þ. See Ref. [58] for full details and explanation. Table 5 given below has the important characteristics of the three regimes associated with this process. In regime I, the rate of deposition of the secondary nucleus is much lower than that of spreading, in regime II these two processes have equivalent rates, and in regime III growth occurs through deposition of multiple nuclei, without any significant contribution from the spreading process [121,122]. The presence of short-chain branches has a complex effect of crystallization, primarily due to the inherent heterogeneity in structure of individual polymer molecules that exhibit considerable levels of short-chain branches. It is known that in the LLDPEs, which are synthesized using the conventional heterogeneous Ziegler-Natta catalyst systems, the distribution of the short-chain branching is not uniform across different molecular weight chains [58,59,61]. The short-chain branches are believed to be preferentially located on the shorter chains as opposed to the longer, higher molecular weight chains [58,59,61]. This essentially means that a LLDPE sample consists of linear high-molecular weight chains and highly branched short chains. To separate the effect of molecular weight and branching on the crystallization process, Lambert and Phillips [58] conducted isothermal crystallization studies on a series of ‘‘cross-fractionated’’ [58] LLDPE samples. These samples gave them the ability to look at the effects of these two Table 5
n
Relationship between rate parameters i and g in the three regimes, and the value of n Regime I
Regime II
Regime III
i{g 4
iBg
iWg
2
4
156
Gregory Beaucage and Amit S. Kulkarni
structural parameters of molecular weight and branching separately. Since the low-molecular weight fractions would have a higher degree of branching, these samples could be analyzed for the effects of branch content on the kinetics of the crystallization process. It would make sense to first discuss what variations in the crystallization process could be expected due to the presence of branches, before presenting the results from the work of Lambert and Phillips [58]. Branch points are considered as defects along the main chain, and hence have to be excluded from the secondary nucleation step. This would inherently lead to a decrease in the rate of secondary nucleation, i. This is in accord with the theory given by Andrews et al. [123] which put forth the idea that presence of defects on the main chain caused an ‘‘inverse logarithmic’’ [58,123] decrease in the growth rate. The process of spreading, though energetically favored as compared to the secondary nucleation step, occurs through the diffusion of the polymer chain onto the surface created by the secondary nucleus deposition. This is essentially a kinetically controlled process, and reptation [59,124] is believed to be a primary mechanism in this transport process. It is well known that the presence of branching affects the reptation process, since the presence of a branch point means that reptation can occur only if it is accompanied by the retraction of the branch [124]. Figure 16 shows the tube model for reptation and how the presence of branches is expected to significantly alter the relaxation times for the polymer molecule. Since branching would be expected to affect both the rate of secondary nucleation and spreading, the presence of branches would also determine the regime in which the crystallization process occurs. Figure 17 from the work of Lambert and Phillips [58] shows the effect of branching in low-molecular weight fractions of LLDPE on the linear growth rates of the secondary nucleation process. Sample H-1 is the linear control sample and the degree of branching increased in the following order for the other samples S-7WS-1WS-4 [58,59]. These samples contained hexyl branches at between 4 and 22 branches/1,000 C (octene was used as the comonomer). As can be seen in the plot the transition between Regime I and Regime II occurs at lower temperatures with increased branching. The transition temperature shifts from 125.31C for the linear sample (H-1) to 123.11C for sample S-7 [58]. From the calculations for the rate parameters i and g, it was seen that the rate of both the secondary nucleation and spreading
Figure 16 Tube model for reptation of a branched polymer molecule from the work of Blackwell et al. [124]. Reproduced with permission from Blackwell et al. [124]. Copyright 2000, The Society of Rheology, Inc.
Chain Structure Characterization
logG + U* 12.3R(T-T_)
1.5
157
H-1 S-4 S-1 S-7
Tb = 123.6C
Tb = 123.3C 0.5
Tb = 123.1C -0.5
Tb = 124.1C
-1.5
-2.5 10.0
14.0
18.0 1/TΔT f
22.0
(x105)
Figure 17 Effect of branching on the secondary nucleation and linear growth rates from the work of Lambert and Phillips [58]. The effect of branching on the Regime I–II transition can also be seen. Reprinted with permission from Lambert and Phillips [58]. Copyright 1994, American Chemical Society.
decreased with increased branching. The interesting result though was the different extents to which branching affected these parameters. The decrease in the rate of secondary nucleation was more pronounced than the decrease in the rate of spreading. This could explain the decrease in the transition temperatures between Regime I and II. Since the rate of secondary nucleation was seen to be affected more than the rate of spreading, it was obvious that this would lead to an extension in the temperature window over which the Regime I was exhibited. In subsequent calculations, Lambert and Phillips [58] also showed that the value of free energy of folds, se, decreased with increased branching, which pointed to a greater occurrence of non-adjacent re-entry process. The greater reduction in the secondary nucleation rate compared to the spreading rate pointed in the direction of total rejection of branched moieties from the secondary nucleation process [58]. The cross-fractionated samples used here allowed for isolating the effects of short-chain branching and molecular weight on the crystallization process. In a companion paper, Lambert and Phillips [59] looked at the combined effect of branch content and molecular weight. The samples used in this work included high-molecular weight fractions with branching. The results from the lower molecular weight branched samples [59] (called as intermediate molecular
158
Gregory Beaucage and Amit S. Kulkarni
weight samples) were similar to the results from their previous paper [58], i.e., they saw a reduction in the crystallization rates, and a reduction in the transition temperature between Regime I and II. The results on the linear growth studies from the work of Lambert and Phillips [59] are shown in Figure 18a. Sample S-5, which was a branched sample with about 6 branches/1,000 C, had the highest molecular weight in this series with a weight average molecular weight of around 89,000 [59]. This sample did not display Regime I behavior. The entire data set obtained for this sample was ascribed to the Regime II of crystallization. This could be due to a direct result of its molecular weight, which is high enough so as to suppress Regime I. Reptation would be slower at higher molecular weights, and this would lower the rate of spreading, g, and the occurrence of entanglements could enhance the secondary nucleation step, thus increasing the value of i. The results seen for sample S-5 were corroborated from the results for the higher molecular weight fractions in which Regime I crystallization was totally absent (Figure 18b). Most of these high-molecular weight samples exhibited Regime II and III. As in the low-molecular weight samples, these samples also showed a branch content dependency on the transition temperature between Regimes II and III (it was between Regime I and II in case of the low-molecular weight samples). Additionally, as could be seen in the case of sample S-6, Regime II is absent due to its very high molecular weight (174,000 Mw). The complex effects of branching and molecular weight on the kinetics and nature of the crystallization process are depicted in Table 6. The main conclusions from this work are that the presence of branching usually suppresses the transition temperature between regimes, essentially suppressing the higher-order
1
b
F - 3 (0) S - 5 (6.67) S - 8 (13.64) S - 2 (16.28) E - 65 (32)
0
LOG 1/t1/2 + U* /2.3R (Tc-T∞)
LOG 1/t1/2 + U* /2.3R (Tc-T∞)
a
-1
-2
-3
-4
1 NBSI 484 (0) S - 6 (2.86) S - 3 (5.46) S - 9 (11.05)
0
-1
-2
-3
-4 4
7
10
13
16
1/TΔTf (x10)
19
22
7
9
11
13
15
17
1/TΔTf (x10)
Figure 18 Effect of branching on the secondary nucleation and linear growth rates from the work of Lambert and Phillips [59]. (a) Low molecular weight samples. Sample S-5 exhibits only Regime II behavior as explained in the text. (b) High molecular weight samples. Reprinted with permission from Lambert and Phillips [59]. Copyright 1996, Elsevier.
Chain Structure Characterization
159
Table 6 Schematic representation of the effects of branching and molecular weight on the crystallization kinetics and the appearance of the Regimes in crystallization
Regime I
Regime II
Regime III
Linear Low Mol Wt Low Mol Wt Branched High Mol Wt High Mol Wt Branched
crystallization regime, whereas higher molecular weights usually suppress the lower-order regime due to a reduction in the rate of spreading due to kinetic effects of molecular weight on a diffusive process like reptation. The LLDPEs used in the work of Lambert and Phillips [58,59] were obtained from heterogeneous Ziegler-Natta catalysts. It was known that the distribution of short-chain branches in polymers obtained from such a catalyst is not uniform. To study the effect of the sequence length distribution, which essentially is determined by how the branches are distributed, Kim and Phillips [125] compared the isothermal crystallization behavior of LLDPEs obtained from both Ziegler-Natta as well as metallocene catalyst systems. The ethylene-octene copolymers obtained from the homogeneous metallocene system showed a linear decrease in the peak melting temperatures as a function of branch content (Figure 19a) [125]. This linear dependency was not seen in the case of the heterogeneous catalyst system (Figure 19b) [125]. In fact, the depression in the peak melting temperatures in the Ziegler-Natta catalysts was not as pronounced as in the case of the metallocene polyethylenes. This important result showed that though the presence of branches had an impact on the crystallization behavior of these polymers, the primary modulator was the distribution of these branches or the sequence length [125]. Thus heterogeneity in the polymer chain microstructure was the deciding factor in the crystallization behavior of these materials. The conclusion that metallocene catalysts give rise to more uniform copolymers with little inter-chain heterogeneity or intra-chain heterogeneity as compared to Ziegler-Natta catalysts has been contended in the literature [126]. Mirabella and Crist [126] performed calorimetric studies on a series of ethyleneoctene/hexene copolymers obtained from both Ziegler-Natta and metallocene catalysts. The peak melting temperatures for some of these samples are shown in Figure 20 as a function of the comonomer content. They observed a linear dependency in the reduction of the peak melting point with increasing branch content in both the cases. They concluded that the assumption that Ziegler-Natta catalyst systems give rise to compositionally heterogeneous copolymers is
160
Gregory Beaucage and Amit S. Kulkarni
a
b 130.0
HLDE MLPE
130.0
L4-0
115.0 H7-O
115.0
Tm(°C)
100.0
L10-O L13-O
H17-O H16-O
100.0
L30-B L40-P L18-O L24-O
Tm(°C)
H10-O
85.0
70.0
85.0
70.0 Low Mw
55.0
55.0
L93-P
High Mw Medium Mw
L39-O
40.0 0.000
0.025
0.050
0.075
40.0 0.00
0.100
0.01
0.02
0.04
PB
SCB/1000C
Figure 19 (a) Peak melting temperature as a function of the branch content in ethyleneoctene copolymers (labelled –O, and symbol K; B (symbol, &) and –P (symbol, W) are for ethylene-butene and ethylene-propylene copolymers, respectively) and obtained from homogeneous metallocene catalysts show a linear profile. (b) Ziegler-Natta ethylene-octene copolymers do not show a linear relationship between peak melting point and branch content [125]. Reproduced from Kim and Phillips [125]. Reprinted with permission of John Wiley & Sons, Inc.
140
140 130
ZN fractions Metallocene fractions Metallocene whole
110 100
ZN fractions Metallocene fractions
130
Tm(°C)
Tm(°C)
120
120
90
110
80
100
70 60 0.00
0.02
0.04
0.06 0.08 XH
0.10
0.12
0.14
90 0.00
0.01
0.02
0.03
0.04
0.05
0.06
0.07
XO
Figure 20 Linear dependence of peak melting temperature with branch content in terms of comonomer (left: hexene; right: octene) content from the work of Mirabella and Crist [126]. Reproduced from Mirabella and Crist [126]. Copyright 2004, John Wiley & Sons, Inc. Reprinted with permission of Wiley-Liss, Inc., a subsidiary of John Wiley & Sons, Inc.
incorrect [126]. The reason for the disparity in this behavior observed in their study compared with the work of Kim and Phillips [125] could be because of the molecular characteristics of the samples used. The high-molecular weight copolymers used by Kim and Phillips [125] had a maximum branch content of about 16 branches/1,000 C, whereas copolymers with comparable molecular weight in the work of Mirabella and Crist [126] had branch content as high as
Chain Structure Characterization
161
84 branches/1,000 C as estimated from NMR spectroscopy. The disparity in the work of Mirabella and Crist [126] could be because of this large difference in the branch content of their samples.
2.3.2 Metallocene and Ziegler-Natta catalyst systems In light of the literature reports that indicate an overbearing significance of the catalyst systems used on the occurrence of inter- and intra-chain heterogeneity in ethylene-a-olefins copolymers, this section shall briefly review the structure of Ziegler-Natta and metallocene catalysts. The Ziegler-Natta catalysts most used currently are titanium tetrachloride supported on magnesium chloride with triethylaluminium used as a co-catalyst [127]. This is essentially a heterogeneous system with the monomers being polymerized, and represents sites with differing catalytic activity and hence close control of the macromolecular architecture is not possible [128]. However, metallocene catalysts represent a sandwiched system with only a single active site, and are homogeneous since they can be dissolved in hydrocarbons [128]. The activity of metallocene catalysts received a huge boost by the synthesis of a co-catalyst methylaluminoxane [129]. These systems can have an activity of about 10,000 times [128] that of Ziegler-Natta polymerizations and are needed at extremely low loadings. Figure 21 shows the structure of methylaluminoxane and some frequently used metallocene catalysts. These are some key advantages that the metallocene catalysts have over conventional Ziegler-Natta catalysts and hence it is highly probable that interand intra-chain heterogeneity expected in ethylene-a-olefins copolymers can be controlled through the use of the metallocene system.
2.3.3 Sequence length distributions The previous sections in this chapter have tried to stress upon the significance of distribution of sequence lengths in polyethylene-based copolymers. The sequence length of interest in a system of ethylene-octene copolymers would be the number of methylene units before a hexyl branch point. As was discussed, this parameter has a greater impact on the crystallization behavior of these polymers than any other structural feature like branch content, or the comonomer fraction. The importance of sequence length distributions is not just limited to crystallization behavior, but also determines the conformational,
Figure 21 Structure of methylaluminoxane (extreme left), and some metallocene catalyst systems. Reproduced from Kaminsky [128], with permission of The Royal Society of Chemistry.
162
Gregory Beaucage and Amit S. Kulkarni
morphological, rheological, and mixing properties of the copolymer. Though techniques like 13C-NMR spectroscopy can determine the sequences, this technique is usually limited, in that it cannot positively differentiate sequences longer than six carbon atoms long. In some very recent work by Karssenberg et al. [130], attempts have been made to improve the analytical ability of a technique like NMR spectroscopy to effectively predict the distribution of sequence lengths in polyethylene-alkene copolymers. They analyzed the entire 13C-NMR spectrum for homogeneous ethylene-propene copolymers. They used quantitative methods based on Markov statistics to obtain sequence length distributions as shown in Figure 22 [130]. The 0.3
(a)
Normalized ethylene sequence length distribution Normalized ethylene sequence mass distribution
nE (S) WE (S)
0.25 0.2 0.15 0.1 0.05 0 0
20
10
30
Sequence length (s) 0.9
(b)
Normalized ethylene sequence length distribution Normalized ethylene sequence mass distribution
0.8
nP (S) WP (S)
0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0
1
2
3
4
5
6
Sequence length (s)
Figure 22 Sequence length distributions for ethylene-propene copolymers (Karssenberg et al. [130]). Top: normalized ethylene sequence length distribution; bottom: normalized propylene sequence length distribution. Reproduced from Karssenberg et al. [130]. Copyright 2006, John Wiley & Sons, Inc. Reprinted with permission of Wiley-Liss, Inc., a subsidiary of John Wiley & Sons, Inc.
Chain Structure Characterization
163
accuracy of such a technique will have to be established by carrying out similar analysis on copolymers obtained from Ziegler-Natta catalysts, and could serve as direct proof of the blocky-nature of branch distribution in such systems.
2.4 Hyperbranched polymers Synthesis and characterization of HBPs have become topics of great interest in the past 15 years and HBPs are characterized by a randomly branched structure as opposed to the controlled molecular topology of dendrimers [131]. Various synthesis routes exist and have been developed recently, though the very first synthesis was carried out from condensation of ABx type of monomers with xX2 [132,133]. Other synthesis routes include the original single monomer synthesis using ABx (xX2) monomers, via self-condensation [134], self-condensing vinyl polymerization [135], ring opening polymerization [136], and proton transfer polymerization [137]. A generic route to the synthesis and structure of a HBP is shown in Figure 23. In addition, double monomer synthesis routes have been developed where the reaction of A2 and Bx (x W 2) monomers, yields structures that can be described as HBPs [138]. Interest in the field of HBPs has seen a phenomenal increase in recent years, in part due to the exciting possibilities offered by these topologically unique materials. The molecular architecture of HBPs has lead to numerous potential applications of these materials like special classes of optical [139], magnetic [140], and conductive [141] materials. HBPs have also found applications in nano-composite films [142], as biomaterials [143] and molecular encapsulates [144]. One of the main reasons for the unique properties of HBPs is the molecular geometry of these disordered structures, in addition to their degree of branching, molecular weight, and polydispersity. The random branched structure of HBPs potentially yields a number of structural isomers, which has a bearing on the final properties of these materials. Like dendrimers, HBPs generally exhibit greater solubility compared to linear polymers. The glass transition temperatures of HBPs can also be very sensitive to the various numbers of structural isomers that could be present for any given chemistry. Conventionally, degree of branching (Db) has been used as a tool to quantitatively describe the architecture of HBPs. Different groups or units in a HBP can be classified as being linear (L), branched (B), or terminal (T) as shown
Figure 23 General structure of a hyperbranched polymer synthesized by the polymerization of AB2 monomer.
164
Gregory Beaucage and Amit S. Kulkarni
in Figure 24. The degree of branching, Db, according to this classification of individual units is expressed as the ratio [22,145–146], Db ¼
BþT BþTþL
(52)
of the sum of branched and terminal units to the total number of units in the HBP. 13 C-NMR can be used to give a quantitative estimate of such branch contents for HBPs. The different chemical environments of the terminal, branched, and linear units can be resolved in the NMR spectra of some of the polymers with this architecture. Such specific assignments in a NMR spectrum are based on the line widths of the resonance peaks, which in turn are inversely proportional to the mobility of those species [145,146]. The mobility of the units would be expected to increase and have the following trend, TWLWB. Hence from such a measurement, quantitative estimates of Db to characterize the architecture of such polymers can be established.
a) B
B
AB
terminal (t)
B
BA
AB
branched (b)
linear (l)
b) Branched Linear
Branched
Linear
O O
Terminal
O
O OCH3
O
OCH3
OCH3
Terminal
O
O O
O
OCH3
O
O
O
O
O
O
O
OCH3
O
O OCH3
OCH3
Figure 24 (a) Classification of different units in a hyperbranched polymer, branched, linear, and terminal [145]. Reproduced from Feast et al. [145] with permission from The Royal Society of Chemistry. (b) branched, linear, and terminal units in hyperbranched poly(dimethyl 5-(4-hydroxy butoxy) isophthalate) [146]. Reproduced from De Luca and Richards [146]. Copyright 2003, John Wiley & Sons, Inc. Reprinted with permission of Wiley-Liss, Inc., a subsidiary of John Wiley & Sons, Inc.
Chain Structure Characterization
165
3 1
119.9
119.8
2
119.7
119.6
119.5
119.4
Figure 25 13C-NMR spectrum for poly(dimethyl 5-(4-hydroxy butoxy) isophthalate) [146]. Reproduced from De Luca and Richards [146]. Copyright 2003, John Wiley & Sons, Inc. Reprinted with permission of Wiley-Liss, Inc., a subsidiary of John Wiley & Sons, Inc.
A 13C-NMR spectrum for poly(dimethyl 5-(4-hydroxy butoxy) isophthalate) [146] is shown in Figure 25. The terminal units with the highest mobility (peak 1) is to the left of the spectrum, whereas the least mobile branched units (peak 2) are at the right, whereas the linear units with intermediate mobility (peak 3) are seen as the central peak.
3. SUMMARY Polymer chain structure is characterized by a hierarchical model based on statistical scaling transitions in a polymer coil at thermal equilibrium. On the smallest scale short-range enthalpic interactions dominate and the chain displays local persistence associated with the Kuhn length. At larger sizes the structure depends on a balance between thermal energy, chain entropy, and long-range interaction enthalpy. The large-scale structure is based on the Brownian model with perturbations associated with concentration, temperature, externally applied force and structural topology related to chain branching. These factors can lead to changes in the chain scaling. A linear coil displays four possible largescale states, extended chain in response to an external field, SAW, Gaussian, and collapsed states. The coil can respond to perturbations through the formation of a size of scaling transition, which is called a blob. Depending on the perturbation the nature of the scaling transition varies. These include concentration blob, thermal blob, and tensile blob. Other scaling transitions are likely to exist in response to structural perturbations. The effects of tacticity and short-chain branching on persistence were discussed as well as the control of crystalline
166
Gregory Beaucage and Amit S. Kulkarni
morphology. Methods to quantify long-chain branching and the consequences on the coil model were also presented. Finally a brief discussion of HBPs was given. Effective deduction of polymer chain structure can be obtained using a variety of analytic and empirical pathways. The multitude of variables associated with fundamental features associated with a polymer chain, e.g., architecture (linear, branched, cyclic, etc.), crystallization (crystalline morphology), chemistry (block, alternating, or random copolymers), conformation and configuration can be effectively characterized with an equally diverse set of characterization tools. From very basic information regarding the hydrodynamic features of the polymer chain/coil as deduced by viscometry, to complex information regarding the tacticity and branching from techniques based on NMR spectroscopy, chain structure characterization often is the crux of obtaining structure–property relationships. Light scattering is often used to obtain information regarding the molar mass of the polymer sample, and is often used in conjunction with other detector systems in GPC. Techniques based on IR spectroscopy are critical in the chemical characterization of the basic building blocks of a polymeric system, the functional group analysis. Critical information regarding the structure of an individual polymer chain has also been effectively characterized with the advent of neutron scattering techniques. Through the application of specific techniques, it is possible to extract information critical for addressing specific problems, ranging from material selection to failure analysis, and is an integral part of developing any effective structure–property relationship road map.
REFERENCES 1 G. Porod, Monatsh. Chem., 80 (1949) 251. 2 O. Kratky and G. Porod, Rec. Trav. Chim. Pays-Bas, 68 (1949) 1106. 3 G. Beaucage, S. Rane, S. Sukumaran, M.M. Satkowski, L.A. Schechtman and Y. Doi, Macromolecules, 30 (1997) 4158. 4 See, for example, the chapter (p. 363) by O. Kratky and the chapter by R. G. Kirste and R. C. Oberthur, In: O.Glatter and O. Kratky (Eds.), Small Angle X-ray Scattering, Academic Press, New York, 1982. 5 See, for example, Feigin L. A. and Svergun D. I., Structure Analysis by Small-Angle X-ray and Neutron Scattering, Plenum Press, New York, 1987. 6 J.S. Higgins and H.C. Benoit, Polymers and Neutron Scattering, Oxford Science Publications, Oxford, U.K., 1994. 7 See, for example, Schmidt P. W., J. Appl. Crystallogr., 15 (1992) 567–569. 8 P.J. Flory, Statistical Mechanics of Chain Molecules, Interscience Publishers, New York, 1969. 9 H. Benoit and P. Doty, J. Phys. Chem., 57 (1953) 958. 10 M. Doi and S.F. Edwards, The Theory of Polymer Dynamics, Oxford Science Publications, Clarendon Press, New York, 1986. 11 P. Degennes, Scaling Concepts In Polymer Physics, Cornell University Press, Ithaca, NY, 1979. 12 S. Sukumaran, G. Beaucage, manuscript in preparation, 2008. 13 M.V. Volkenstein, Configurational Statistics of Polymeric Chains, Interscience, New York, 1963. 14 D.Y. Yoon and P.J. Flory, Polymer, 16 (1975) 645. 15 D.Y. Yoon and P.J. Flory, Macromolecules, 9 (1976) 294. 16 D.Y. Yoon and P.J. Flory, Macromolecules, 9 (1976) 299. 17 W. Wunderlich and R.G. Kirste, Ber. Bunsen-Ges. Phys. Chem., 68 (1964) 646.
Chain Structure Characterization
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63
167
R.G. Kirste, Makromol. Chem., 101 (1967) 91. R.G. Kirste, J. Polym. Sci. Part C, 16 (1967) 2039. W. Kuhn, Kolloid-Z., 68 (1934) 2. S.T. Sun, I. Nishio, G. Swislow and T. Tanaka, J. Chem. Phys., 73 (1980) 5971. B. Farnoux, F. Boue, J.P. Cotton, M. Daoud, G. Jannink, M. Nierlich and P.G. De Gennes, J. Physique, 39 (1978) 77. I. Noda, N. Kato, T. Kitano and M. Nagesowa, Macromolecules, 14 (1981) 668. S.K. Sukumaran and G. Beaucage, Europhys. Lett., 59 (2002) 714. P. Pincus, Macromolecules, 9 (1976) 386. F.A. Bovey and G.V.D. Tiers, J. Polym. Sci., 44 (1960) 173. L.H. Sperling, Introduction to Physical Polymer Science, 4th ed., Wiley, New York, 2006. J.M. O’ Reilly and R.A. Mosher, Macromolecules, 14 (1981) 602. J.L. Koenig, Spectroscopy of Polymers, 2nd ed., Elsevier, New York, 1999. J.L. Koenig, Chemical Microstructure of Polymer Chains, Wiley, New York, 1980. D.A.C. Compton and W.F. Maddams, Appl. Spectrosc., 40 (1986) 239. E. Rojo, B. Pena, M.E. Munoz and A. Santamaria, Macromol. Chem. Phys, 207 (2006) 1781. B. Pena, Rev. Plast. Mod., 83 (2002) 296. S. Mansel and E.P. Tabernero, Rev. Plast. Mod., 75 (1998) 361. L. Mandelkern, Crystallization of Polymers, 2nd ed., Cambridge University Press, New York, 2002. D.J. Kohls and G. Beaucage, Curr. Opin. Solid State Mater. Sci., 6 (2002) 183. A.I. Medalia, Rubber Chem. Technol., 60 (1987) 45. K.E. Polmanteer and C.W. Lentz, Rubber Chem. Technol., 48 (1975) 795. A.I. Medalia, J. Colloid Sci., 32 (1970) 115. T. Gruber, T. Zerda and M. Gerspacher, Rubber Chem. Technol., 67 (1994) 280. T.A. Witten, M. Rubinstein and R.H. Colby, J. Phys. II, 3 (1993) 367. R.G. Alamo, W.W. Graessley, R. Krishnamoorti, D.J. Lohse, J.D. Londono, L. Mandelkern, F.C. Stehling and G.D. Wignall, Macromolecules, 30 (1997) 561. X.B. Zhang, Z.S. Li, H. Yang and C.C. Sun, Macromolecules, 37 (2004) 7393. P.J. Barham, M.J. Hill, A. Keller and C.C.A. Rosney, J. Mater. Sci. Lett., 7 (1988) 1271. M.J. Hill, P.J. Barham, A. Keller and C.C.A. Rosney, Polymer, 32 (1991) 1384. M.J. Hill, P.J. Barham and A. Keller, Polymer, 33 (1992) 2530. G.D. Wignall, J.D. Londono, R.G. Alamo, L. Mandelkern and F.C. Stehling, Macromolecules, 29 (1996) 5332. F.M. Mirabella and E.A. Ford, J. Polym. Sci. Polym. Phys. Ed., 25 (1987) 777. F.M. Mirabella, S.P. Westphal, P.L. Fernando, E.A. Ford and J.G. Williams, J. Polym. Sci. B, 26 (1995) 1995. A. Nesarikar and B. Crist, J. Polym. Sci. B, 32 (1994) 641. C.H. Stephens, A. Hiltner and E. Baer, Macromolecules, 36 (2003) 2733. A.S. Kulkarni and G. Beaucage, Polymer, 46 (2005) 4454. J. Vega, M. Aguilar, J. Peon, D. Pastor and J. Martinez-Salazar, e-Polymer, 046 (2002) 1. E.A. Jordan, A.M. Donald, L.J. Fetters and L. Klein, J. Polym. Prepr., ACS Div. Polym.Chem., 30 (1989) 63. C.B. Gell, W.W. Graessley, V. Efstratiadis, M. Pitsikalis and N. Hadjichristidis, J. Polym. Sci. Part B: Polym. Phys., 35 (1997) 1943. L.J. Kasehagen, C.W. Macosko, D. Trowbridge and F. Magnus, J. Rheol., 40 (1996) 689. P.M. Wood-Adams, J.M. Dealy, A.W. deGroot and O.D. Redwine, Macromolecules, 33 (2000) 7489. W.S. Lambert and P.J. Phillips, Macromolecules, 27 (1994) 3537. W.S. Lambert and P.J. Phillips, Polymer, 37 (1996) 3585. J.I. Lauritzen and J.D. Hoffmann, J. App. Phys., 44 (1973) 4340. J. Wagner and P.J. Phillips, Polymer, 42 (2001) 8999. Y.H. Kim and O. Webster, In: M.K. Mishra and S. Kobayashi (Eds.), Star and Hyperbrached Polymers, Marcel Dekker, New York, 1999. (a) C. Gao and D. Yan, Prog. Polym. Sci., 29 (2004) 183. (b) Y.H. Kim, J. Polym. Sci. Part A: Polym. Chem., 36 (1998) 1685.
168
Gregory Beaucage and Amit S. Kulkarni
64 (a) Y.H. Kim and O.W. Webster, Macromolecules, 25 (1992) 5561. (b) C.J. Hawker, R. Lee and J.M.J. Fre´chet, J. Am. Chem. Soc., 113 (1991) 4583. 65 R. Agarwal, J. Horsk, J. Stejskal, O. Quadrat and P. Kratochvil, J. App. Polym. Sci., 28 (1983) 3453. 66 E.E. Drott and R.A. Mendelson, J. Polym. Sci., 8 (1970) 1361. 67 F.M. Mirabella, L. Wild, Polymer Characterization: Physical Property, Spectroscopic, and Chromatographic Methods, C. D. Craver and T. Provder (Eds.), Advances in Chemistry Series 227, American Chemical Society, Washington DC, 1990, pp. 23–44. 68 A. Rudin, In: H. G. Barth and J. W Mays (Eds.), Modern Methods of Polymer Characterization, Wiley, New York, 1991, pp. 103–112. 69 B.H. Zimm and W.H. Stockmayer, J. Chem. Phys., 17 (1949) 1301. 70 F. Beer, G. Capaccio and L.J. Rose, J. App. Polym. Sci., 73 (1999) 2807. 71 F.A. Bovey and P.A. Mirau, NMR of Polymers, Academic Press, New York, 1996, pp. 199–203. 72 D. Yan, W.J. Wang and S. Zhu, Polymer, 40 (1999) 1737. 73 M. Pollard, K. Klimke, R. Graf, H.W. Spiess and M. Wilhelm, Macromolecules, 37 (2004) 813. 74 A. Kurkiewicz, N.W. Eilerts and E.T. Hsieh, Macromolecules, 32 (1999) 5471. 75 P.M. Cotts, Z. Guan, E. McCord and S. McLain, Macromolecules, 33 (2000) 6945. 76 F.A. Bovey, Pure App. Chem., 54 (1982) 559. 77 M.H. George, R.J. Grisenthwaite and R.F. Hunter, Chem. Ind. (1958) 1114. 78 W.H. Starns, F.C. Schilling, K.B. Abbas, I.M. Plitz, R.L. Hartless and F.A. Bovey, Macromolecules, 12 (1979) 13. 79 D.M. Grant and E.G. Paul, J. Am. Chem. Soc., 86 (1964) 2984. 80 J.C. Randall, Polymer Sequence determination: Carbon-13 NMR Method, Academic Press, New York, 1977, pp. 12–17. 81 J.C. Randall, J. Polym. Sci. Part B: Polym. Phys., 13 (1975) 901. 82 W. Liu, D.G. Ray, III and P.L. Rinaldi, Macromolecules, 32 (1999) 3817. 83 G. Beaucage, Phys. Rev. E: Stat. Nonlin. Soft. Matter Phys., 70 (2004) 031401. 84 P.M. Wood-Adams and J.M. Dealy, Macromolecules, 33 (2000) 7481. 85 R.N. Shroff and H. Mavridis, Macromolecules, 32 (1999) 8454. 86 J.P. Hogan, C.T. Levett and R.T. Werkman, SPE J, 23 (1967) 87. 87 B.H. Bersted, J.D. Lee and C.A. Richter, J. App. Polym. Sci., 26 (1981) 1001. 88 B.J. Crosby, M. Mangnus, W. de Groot, R. Daniels and T.C.B. McLeish, J. Rheol., 46 (2002) 401. 89 T.C.B. McLeish and S.T. Milner, Advances in Polymer Science, 143, Springer, Berlin, 1999, pp. 197–256. 90 C.G. Robertson, C.A. Garcia-Franco and S. Srinivas, J. Polym. Sci. Part B: Polym. Phys., 42 (2004) 1671. 91 J.F. Vega, M. Fernandez, A. Santamaria, A. Munoz-Escalona and P. Lafuente, Macromol. Chem. Phys., 200 (1999) 2257. 92 S. Lai and G.W. Knight, SPE ANTEC Tech. Papers, 39 (1993) 1118. 93 Y.S. Kim, C.I. Chung, S.Y. Lai and K.S. Hyun, SPE ANTEC Tech. Papers, 41 (1995) 1122. 94 Y.S. Kim, C.I. Chung, S.Y. Lai and K.S. Hyun, J. App. Polym. Sci., 59 (1996) 125. 95 Y.S. Kim, C.I. Chung, S.Y. Lai and K.S. Hyun, Korean J. Chem. Eng., 13 (1996) 294. 96 J.F. Vega, A. Munoz-Escalona, A. Santamaria, M.E. Munoz and P. Lafuente, Macromolecules, 29 (1996) 960. 97 J.F. Vega, A. Santamaria, A. Munoz-Escalona and P. Lafuente, Macromolecules, 31 (1998) 3639. 98 S.G. Hatzikiriakos, I.B. Kazatchkov and D. Vlassopoulos, J. Rheol., 41 (1997) 1299. 99 A. Malmberg, C. Grabiel, T. Strffl, H. Munstedt and B. Lofgren, Macromolecules, 35 (2002) 1038. 100 S.Y. Lai, T.A. Plumley, T.I. Butler, G.W. Knight and C.I. Kao, SPE ANTEC Technol. Papers, 40 (1994) 1814. 101 R. Shroff and H. Mavridis, J. App. Polym. Sci., 57 (1995) 1605. 102 P.M. Wood-Adams and J.M. Dealy, J. Rheol., 40 (1996) 761. 103 J. Janzen and R.H. Colby, J. Mol. Struct., 485–486 (1999) 569. 104 P.M. Wood-Adams and S. Costeux, Macromolecules, 34 (2001) 6281. 105 A.S. Kulkarni and G. Beaucage, J. Polym. Sci. Part B: Polym. Phys., 44 (2006) 1395.
Chain Structure Characterization
169
106 R.J. Roe, Methods of X-ray and Neutron Scattering in Polymer Science, Oxford University Press, New York, 2000. 107 G. Beaucage, J. App. Cryst., 28 (1995) 717–728. 108 T.A. Witten, M. Rubinstein and R.H. Colby, J. Phys. II, 3 (1993) 367. 109 P. Meakin, Prog. Solid State Chem., 20 (1990) 135–233. 110 G. Beaucage, H.K. Kammler and S.E. Paratsinis, J. App. Cryst., 37 (2004) 523–535. 111 G. Beaucage, J. App. Cryst., 29 (1996) 134–146. 112 G. Beaucage, S. Rane, S. Sukumaran, M.M. Satkowski, L.A. Schechtman and Y. Doi, Macromolecules, 30 (1997) 4158–4162. 113 J. Skilling and R.K. Bryan, Mon. Not. R. Astron. Soc., 211 (1984) 111. 114 J. Ilavsky, Particle Size Distribution from USAXS, A Manual for USAXS Analysis, UNICAT, Argonne Illinois, USA, http://www.uni.aps.anl.gov/Bilavsky, 2000. 115 P.R. Jemian, J.R. Weertman, G.G. Long and R.D. Spal, Acta. Metall. Mater., 39 (1991) 2477. 116 H. Boukari, G.G. Long and M.T. Harris, J. Colloid Interf. Sci., 229 (2000) 129. 117 S. Hansen, Acta Cryst. A, 50 (1994) 547. 118 J.D. Morrison, J.D. Corcoran and K.E. Lewis, J. App. Cryst., 25 (1992) 504. 119 J.A. Potton, G.J. Daniel and B.D. Rainford, J. App. Cryst., 21 (1988) 663. 120 A. Tagliani, App. Math. Comput., 112 (2000) 333. 121 P.J. Phillips, Rep. Prog. Phys., 53 (1990) 549. 122 P.J. Phillips, In: D. T. J. Hurle (Ed.), Handbook of Crystal Growth, Vol. 2, Elsevier, North Holland, 1994. 123 E.H. Andrews, P.J. Owen and A. Singh, Proc. Roy. Soc. London A, 324 (1971) 79. 124 R.J. Blackwell, T.C.B. McLeish and O.G. Harlen, J. Rheol., 44 (2000) 121. 125 M.H. Kim and P.J. Phillips, J. App. Polym. Sci., 70 (1998) 1893. 126 F.M. Mirabella and B. Crist, J. Polym. Sci. Part B: Polym. Phys., 42 (2004) 3416. 127 K. Soga and T. Shiono, Prog. Polym. Sci., 22 (1997) 1503. 128 W. Kaminsky, J. Chem. Soc. Dalton Trans. (9) (1998) 1413. 129 H. Sinn, Macromol. Symp., 97 (1995) 27. 130 S.G. Karssenberg, V.B.F. Mathot and J.G. Zwartkruis, J. Polym. Sci. Part B: Polym. Phys., 44 (2006) 722. 131 Y.H. Kim and O. Webster, In: M.K. Mishra and S. Kobayashi (Eds.), Star and Hyperbrached Polymers, Marcel Dekker, New York, 1999. 132 (a) C. Gao and D. Yan, Prog. Polym. Sci., 29 (2004) 183. (b) Y.H. Kim, J. Polym. Sci. Part A: Polym. Chem., 36 (1998) 1685. 133 P. Froehling, J. Polym. Sci. Part A: Polym. Chem., 42 (2004) 3110. 134 (a) Y.H. Kim and O.W. Webster, Macromolecules, 25 (1992) 5561. (b) C.J. Hawker, R. Lee and J.M.J. Fre´chet, J. Am. Chem. Soc., 113 (1991) 4583. 135 J.M.J. Fre´chet, M. Henmi, I. Gitsov, S. Aoshima, M. Leduc and R.B. Grubbs, Science, 269 (1995) 1080. 136 M. Liu, N. Vladimirov and J.M.J. Fre´chet, Macromolecules, 32 (1999) 6881. 137 H.T. Chang and J.M.J. Fre´chet, J. Am. Chem. Soc., 121 (1999) 2313. 138 (a) T. Emrick, H.T. Chang and J.M.J. Fre´chet, Macromolecules, 32 (1999) 6380. (b) C. Gao and D. Yan, Chem. Commun., 1 (2001) 107. 139 T. Lin, Q. He, F. Bai and L. Dai, Thin Solid Films, 363 (2000) 122. 140 N. Spetseris, R. E. Ward T. Y. Meyer, Macromolecules, 31 (1998) 3158. 141 S. Tanaka, T. Iso and Y. Doke, Chem. Commun., 21 (1997) 2063. 142 G. Decher, Science, 277 (1997) 1232. 143 Y. Lim, S.M. Kim, Y. Lee, W. Lee, T. Yang, M. Lee, H. Suh and J. Park, J. Am. Chem. Soc., 123 (2001) 2460. 144 S.E. Stiriba, H. Kautz and H. Frey, J. Am. Chem. Soc., 124 (2002) 9698. 145 W.J. Feast, A.J. Keeny, A.M. Kenwright and D. Parker, Chem. Commun., 18 (1997) 1749. 146 E. De Luca and R.W. Richards, J. Polym. Sci. Part B: Polym. Phys., 41 (2003) 1339. 147 M. Antonietti and C. Rosenauer, Macromolecules, 24 (1991) 3434.
This page intentionally left blank
CHAPT ER
5 Chain End Characterisation Anthony T. Jackson and Duncan F. Robertson
Contents
1. Introduction 2. End Groups in Free Radical Polymers 3. End Groups in Condensation Polymers 4. End Groups in Polymers from Ionic Polymerisation 5. Closing Remarks Acknowledgements References
171 175 182 194 201 201 201
1. INTRODUCTION The characterisation of end group functionalisation from synthetic polymers is important for a number of reasons, and is described in this chapter with particular reference to industrial polymeric systems. End group functionality can be important to the application for the polymeric system, e.g., the end groups are very important in prepolymers for polyurethanes, so that efficient formation of soft blocks and hard blocks, plus cross-linking, can occur. Knowledge of the end groups of a polymer often gives evidence for the polymerisation methodology employed to make the material. Information on the initiators and end-cappers, plus chain transfer agents can be obtained. An example reaction scheme for polymerisation of a free radical polymer system is shown below in Figure 1. The resulting end group fragments in the polymer, therefore, indicate which initiators, chain transfer agents and terminating agents were used (or if no specific terminating agents or chain transfer agents have been employed, such as when disproportionation occurs). The end group functionality of condensation polymers is typically defined by the monomers employed to make these materials. An example is shown below for a common polyamide polymer, namely nylon (see Figure 2). These polymers
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00405-4
r 2008 Elsevier B.V. All rights reserved.
171
172
Anthony T. Jackson and Duncan F. Robertson
Initiation I R• + M
→ →
2R• RM•
Propagation RM• + M RMn• + M
→ →
RM2• RMn+1•
Chain Transfer RMn+1• + AH A• + M AMn• + M
→ → →
RMn+1H + A• AM• AMn+1•
→ →
RMx My R (RMx-H) + (RMy+H)
Termination RMx•+ RMy• RMx•+ RMy•
Combination Disproportionation
Figure 1 Reaction scheme for the free-radical polymerisation (I is the initiator, R the fragment of initiator, M the monomer and AH the chain transfer agent).
O
O
n HOC(CH2)x COH + n +1 H2N(CH2)y NH2
−n +1 H2O
O
O
H2N(CH2)y NH[C(CH2)x CNH(CH2)y NH]nH Nylon
Figure 2 Reaction scheme for the formation of Nylon.
are typically made by reacting a di-amine with a di-acid, such that amine end groups are produced. It is also possible that material with acid end groups is present and possibly cyclic oligomer. The other common type of synthetic polymer made by condensation polymerisation is the polyester, typically manufactured by the reaction of a di-ol with a di-acid. Many ionic polymerisation routes (both cationic and anionic) are also used to make industrial polymers. The end group functionality typically depends on the initiator used to make the polymer. Several modern analytical instruments are powerful tools for the characterisation of end groups. Molecular spectroscopic techniques are commonly employed for this purpose. Nuclear magnetic resonance (NMR) spectroscopy, Fourier transform infrared (FTIR) spectroscopy and mass spectrometry (MS), often in combination, can be used to elucidate the end group structures for many polymer systems; more traditional chemical methods, such as titration, are still in wide use, but employed more for specific applications, for example, determining acid end group levels. Nowadays, NMR spectroscopy is usually the first technique employed, providing the polymer system is soluble in organic solvents, as quantification of the levels of
Chain End Characterisation
173
end groups can often be obtained directly. Calibrations are required for quantification of end groups by means of FTIR spectroscopy. The data obtained from mass spectrometric techniques is most commonly used to obtain qualitative information on end group structure. The sensitivity of many mass spectrometric techniques allows structural information on minor end groups to be obtained, often not available from NMR and FTIR spectroscopy data. The most commonly used NMR spectroscopy techniques are 1H and 13C NMR. The inherent lower sensitivity of 13C NMR, due to the low natural abundance of the 13C isotope, can reduce its applicability for characterisation of polymers of high molecular weight. Characterisation of a lower molecular weight fraction of the polymer, which can often be produced by chromatographic (e.g., using gel-permeation chromatography, GPC) fractionation or solvent extraction, often enhances the end group information that can be obtained. One of the main advantages of FTIR spectroscopy over NMR techniques is that the former does not require the polymer system to be soluble. Data can often be directly obtained from solid polymer, and while not an absolute technique, FTIR spectroscopy can be effective in comparing end group levels in differing molecular weight (MW) samples of the same polymer, sometimes through application of absorption subtraction between their mid-infrared spectra. FTIR microscopes also allow data to be obtained from much more localised regions than available with NMR investigations. This can be useful, for example, in highlighting the cause of a processing-difference-induced defect as a consequence of an end group (MW) difference, such as was the case for a gel-like defect observed in a polysulfone (PES), and characterised as arising from polymer with a lower concentration of aryl–Cl end groups, see Figure 3 [1]. Even though the amount of sample is often not a problem for polymer characterisation, contamination analysis often requires that analysis be performed on a smaller amount of material than that can be analysed by means of NMR spectroscopy. MS-based techniques can also be employed on relatively small amounts of sample, but typically require the polymer to be soluble in organic solvents. Matrix-assisted laser desorption/ ionisation-time of flight (MALDI-TOF) is the most commonly employed mass spectrometric technique, as the simplest data are obtained for end group analysis. Electrospray ionisation-mass spectrometry (ESI-MS) is occasionally preferred for end groups that do not remain intact in the MALDI-TOF technique, as the former is a ‘softer’ methodology. The ESI-MS data obtained from synthetic polymers can often, however, be quite complex due to the nature of the ionisation mechanism. Tandem mass spectrometry (MS/MS) techniques can be employed to obtain additional end group information. The MS/MS method involves selection of individual oligomers prior to fragmentation. The fragments obtained often contain additional information about end group structure to that generated by either MALDI-TOF MS or ESI-MS. The combination of a number of these techniques often provides complementary information on end group structure and hence the mechanism of polymerisation. The synergy between MALDI-TOF MS and NMR spectroscopy is particularly powerful, with MS/MS providing additional information where necessary. MALDI-TOF MS provides information on individual oligomers,
174
Anthony T. Jackson and Duncan F. Robertson
2.2
Absorbance
1.7
1.2
0.7
0.2 850
800
750 700 Wavenumber / cm-1
650
600
Figure 3 FTIR microscopy absorbance spectra (100 mm aperture) recorded from a microtomed section through a defect area of a PES film. The upper spectrum is characteristic of the base film; the lower spectrum is representative of the defect area. The difference in relative intensity of the band at 760 cm1 can be clearly seen; this band is attributable to the aryl–Cl end group. The consequence of this difference was the aryl–Cl end group deficient material processed differently giving rise to a gel-like feature in the polymer film. Reproduced with permission from Chalmers and Everall [1]. Copyright Wiley-VCH Verlag GmbH & Co. KGaA.
whereas NMR spectroscopy data are an average from the whole sample. The data from the former technique can, therefore, be employed to generate information from samples containing varying end group structures. One of the main advantages of MS/MS is that it can be employed to generate information on individual end group structures, whereas MALDI-TOF MS only provides information on the combined mass of both the initiating and terminating functionalisation. Specific examples of how these three techniques may be combined together to generate a full picture of end group functionality in a polymer system are provided below. Three particular examples are described in detail in order to emphasise the methodology; these are the characterisation of end groups from acrylic polymers, from polyesters such as poly(ethylene terephthalate) (PET), and polymers from ionic routes that is highlighted by polyethers. Extraction of low molecular weight fractions from higher molecular weight materials may be required in order to generate structural information, due to the low levels of end groups present. This is particularly important for MALDI-TOF MS and 13C NMR spectroscopic characterisation of end group structure. And while the various NMR and MS methodologies offer good synergies in characterising end groups from many polymer systems, these techniques typically require that the polymeric system is soluble in an organic solvent.
Chain End Characterisation
175
2. END GROUPS IN FREE RADICAL POLYMERS This section focuses on describing on how end group structures can be determined from one particular polymer that was generated by free radical polymerisation (see Figure 1), namely poly(methyl methacrylate) (PMMA, 1). CH3 R′
CH2C
n
R′′
O C OCH3 1
The methodology employed, however, is applicable to many other free radical polymers generated from vinyl monomers (such as, e.g., polystyrene). It should be noted that this methodology is also equally applicable to many polymers generated by condensation and ionic polymerisation routes. PMMA is an industrially produced polymer that has many applications including for kitchen fittings (such as work surfaces) and bathroom furniture (e.g., acrylic baths, sinks and showers), signage, lighting and (more recently) television screens [2]. The major benefits of this polymer are its water-clear colour and stability to ageing, even under severe conditions. Traditional routes of manufacture are by radical polymerisation in which an initiator (possibly peroxide or azo-based) is employed with termination by disproportionation (resulting in a mixture of saturated and unsaturated chain ends). Additional use of a chain transfer agent (e.g., a thiol) can change the majority of both the initiating and terminating chain ends and aid control of the molecular weight distribution [2]. This polymerisation route is described by Figure 1 (vide supra). The combination of NMR- and MS-based techniques is a powerful methodology for generating information on these end group structures. Industrial PMMAbased polymers are often of relatively high average molecular weight, but the high polydispersity of these materials means that a lower molecular weight fraction can often be obtained and characterised by these techniques. A number of controlled living radical polymerisation techniques have been explored over the last decade or so [3], with some commercial polymers resulting from this research. These living radical polymerisation routes include nitroxidemediated polymerisation (NMP) [4], atom-transfer radical polymerisation (ATRP) [5,6] and reversible addition-fragmentation chain transfer (RAFT) [7] polymerisation. These polymerisation routes offer possibilities in controlled architecture of polymers and copolymers that are not typically available from regular free radical polymerisation. These three living radical polymerisation routes result in polymers with different end group structures. Spectroscopic techniques are typically key in understanding the end group structures of these polymers [8,9]. As an example, a description of how these analytical techniques may be employed to characterise the end group structures of PMMA polymers generated by ATRP is described below. The mechanism of ATRP may be described by the scheme shown below (Figure 4). This results in polymer with either bromide- or chloride-terminating
176
Anthony T. Jackson and Duncan F. Robertson
groups, as this functionality is part of the initiator used for the polymerisation and is key to the radical shuttling mechanism that is proposed for ATRP (where X is Br or Cl in Figure 4). The other fragment of the initiator (Ru in Figure 4) should form the initiating (a) end group of the polymer chain from this mechanism. A combination of NMR spectroscopy, MS and FTIR spectroscopy has been employed to verify that the end group structures proposed from this mechanism are correct and, in addition, generate information on any other end group structures resulting from side reactions during polymerisation [10,11]. An ATRP polymer of methyl methacrylate (MMA), made with ethyl-2bromoisobutyrate as the initiator such that 2 may describe the expected structure, was initially characterised by means of 1H and 13C NMR spectroscopy [11]. The resulting 13C NMR spectrum is displayed below in Figure 5 (the region of the spectrum, where the carbonyl resonances occur, between approximately 171–179 ppm is shown in an expansion), with the proposed assignments annotated along with the corresponding letters on the anticipated dominant structure (i.e., 2, shown in an expanded 13C letter labelled form below the spectrum). Several key resonances in the 13C NMR spectrum are consistent with those expected for the proposed end group structures. Peaks a (from non-equivalent methyl carbons at 29 and 22 ppm), b (a quaternary carbon at 41 ppm), c (methylene from the ethyl ester at 60 ppm) and d (methyl group from the ethyl ester at 13 ppm) provide evidence for the presence of the ethyl-iso-butyrate group at the initiating (a) end of the polymer, along with some resonances from the first MMA unit attached to this moiety. Data indicating that the terminating (o) bromide end group is present are provided by peaks from the terminal MMA unit, labelled m (terminal MMA methyl group at 25 ppm), n (terminal MMA quaternary carbon adjacent to bromide group at 58 ppm) and o (carbonyl of terminal methyl ester group from MMA at 172 ppm). The proposed structure accounts for all of the major peaks in the spectrum, indicating the proposed structure (2) dominates for this polymer. Estimations of the average molecular weight of the polymer can be calculated from a comparison of integration values for selected peaks from the backbone with those from the end groups [11]. CH3
CH3
CH3
H3CC
CH2C
O C
O C
H3CH2CO
n
Br
CH3 H3C
CH2C CH2C
O C
O C
n-2
2
CH2
OCH3 O
H3CH2CO
OCH3
CH3 C COCH3 C O O
H3CC
3
CH3
CH3
CH2
CH3
CH3
H3CC
CH2C CH2C
H3CC
CH2C H
O C
O C
O C
O C
n-1
H3CH2CO
O C
OCH3 OCH3 4
n
H3CH2CO
OCH3 5
177
Chain End Characterisation
CH3 MTn
R′X
R′
CH2C
R′
n MMA
MTn
n-1
O C MTn+1X
CH3
C H2C X O C
OCH3 OCH3 Dormant CH3
CH3 R′
CH2C O C
n+1
MT
X
Etc.
CH2C
n-1
O C
OCH3 OCH3 Active
Figure 4 Reaction scheme for ATRP of PMMA (RuX is the initiator, X the Br or Cl and MT the catalyst).
h j
i
g/k
f
h
j
c
f
d
o 178 b
177
176
175
174
173
172 ppm
e a
l
m n
60
55
50
45
40
35
30
25
20
15
ppm
a m f f CH3 CH3 CH3 CH3 l n b g j k H3CC CH2C CH2C CH2CBr a e n-2 o h h h O C O C O C O C d i i i H3CCH2O OCH3 OCH 3 OCH3 c
Figure 5 13C NMR spectrum from PMMA generated by ATRP with ethyl-2-bromoisobutyrate as initiator (see text for details).
178
Anthony T. Jackson and Duncan F. Robertson
MALDI-TOF mass spectrometry was employed to generate confirmatory evidence of the end group structures from the same PMMA polymer [10]. An expansion of the resulting MALDI-TOF mass spectrum is shown in Figure 6. This partial spectrum effectively covers the range of one repeat unit of the polymer (between mass-to-charge ratio (m/z) 1860–1960), which is approximately 100 Da. Interestingly, the dominant series of peaks in this spectrum, emphasised by the expansion, do not have mass-to-charge ratios consistent with the expected structure. Lithium bromide was added as the cationisation agent in the experiment, so peaks from lithiated molecule ions (i.e. [2+Li]+) were expected to be observed in the MALDI-TOF mass spectrum. This component was expected to have a monoisotopic peak at m/z 1901.9 (C91H147O36BrLi for the lithiated 17-mer of structure 2) and a low intensity peak is indeed noted in the spectrum (labelled 2 in Figure 6). Furthermore, the isotope pattern is similar to that expected for a component containing a bromide group (with equivalent amounts of 79Br and 81Br). Previous work [11] indicated that this major component was fragmenting in the ion source of the MALDI-TOF mass spectrometer, leading to the formation of oligomer with a lactone end group
3 Theoretical Isotope Distribution 3
100
% 5
3* 4 2 1900
0 1860
1870
1880
1910
m/z
1890
1920
1900
1910 m/z
1920
1930
1940
1950
1960
Figure 6 Partial MALDI-TOF mass spectrum from PMMA generated by ATRP with ethyl-2bromoisobutyrate as initiator (inset shows theoretical isotope distribution for lithiated 18-mer of structure 3). (Peak labelled 3 arises from post-source decay of 3 [10].)
Chain End Characterisation
179
(structure 3), via loss of methyl bromide from 2. The peak from this lactoneended oligomer, labelled 3 in Figure 6, clearly does not contain any bromine atoms (from the isotope pattern). This demonstrates an important feature of MALDI-TOF MS that with high enough resolution to generate isotope patterns (i.e., using the reflectron mode of operation), such that information on the presence (or not) of elements (e.g., Br and Cl) can be established, distinctive isotope distributions can be obtained. This can provide confirmatory evidence for the presence of some end group structures. A comparison between the theoretical isotope pattern of C95H152O38Li, for the lithiated 18-mer of 3 (see inset in Figure 6), with that experimentally obtained indicates that they are very similar. Furthermore, the experimentally observed monoisotopic peak at m/z 1907.9 is very similar to that expected (m/z 1908.0) for this oligomer. Heating of this polymer [10] generated material that was proposed, from the MALDI-TOF MS and NMR data, to contain little or none of the original bromide terminating end group, with the lactone end group dominating (i.e., oligomer with structure 3). This indicates that this lactone end group is formed by loss of methyl bromide during heating, as well as in the MALDI-TOF MS process (from the original polymer) [10]. A characteristic band from the carbonyl group in the 5-membered lactone ring [12] is clearly discerned in the FTIR spectrum obtained from this heated polymer at approximately 1780 cm1 [10], with low levels of this functionality also probably present in the original polymer (see Figure 7). This demonstrates how FTIR can be employed to provide confirmatory evidence for the presence of selected end group structures in polymers. Evidence for a competing disproportionation mechanism (see Figure 1) for the termination of chain ends is provided by the combined presence of the peaks from 4 and 5 in the MALDI-TOF mass spectrum of this PMMA polymer (see Figure 6) [10]. Confirmation of the presence of the unsaturated and saturated chain ends, arising from disproportionation, was obtained by means of 1H and 13 C NMR spectroscopy, respectively [11]. Another PMMA polymer, generated by ATRP with p-toluene sulphonyl (tosyl) chloride as the initiator, such that structure 6 was the expected dominant end group structure, was also analysed by means of NMR spectroscopy and MALDI-TOF MS. Both 1H and 13C NMR spectroscopy provided data that indicated that the expected tosyl group and chloride functionality were the dominating functionalities at the initiating (a) and terminating (o) chain ends, respectively. The MALDI-TOF MS data from this polymer indicated that 6 was indeed the major component. The partial MALDI-TOF MS spectrum (from m/z 1475–1575), which approximately covers one repeat unit of the polymer, is displayed in Figure 8. Lithium bromide was again used as cationisation agent, so the presence of the major component was expected to be confirmed by observing a monoisotopic peak from the 13-mer at m/z 1497.7 (C72H111SO28ClLi, see theoretical isotope pattern for 13-mer in inset of Figure 8). The dominant peak in the expansion of the experimental spectrum is indeed seen at this mass-to-charge ratio (m/z 1497.7). In addition, close similarities are detected between the
180
Anthony T. Jackson and Duncan F. Robertson
Absorbance
PMMA A-30 mins at 150°C
PMMA A PMMA B
1800
1750
1700
1650
Wavenumber (cm-1)
Figure 7 FTIR spectra from PMMA (two batches, labelled PMMA A and PMMA B) generated by ATRP with ethyl-2-bromoisobutyrate as initiator, before and after heating (only PMMA A was heated) to 1501C for 30 min.
theoretical and experimental isotope distributions from these peaks, indicating that the chlorine functionality is present in this polymer. O H3C
CH3
S
CH2C Cl
O
O C
H3C
n
CH3 H3C
S
CH2C CH2C
O
O C
n-2
CH3 C COCH3 C O O CH2
OCH3 O
OCH3 6
7
O H3C
O
CH2
CH3
S
CH2C
O
O C
CH2C
n-1
O C
OCH3 8
O H3C
OCH3
CH3
S
CH2C H
O
O C
n
OCH3 9
The fragmentation in the MALDI-TOF MS experiment noted from the brominated polymer is less prevalent in this chlorinated material, but evidence for the lactone-ended oligomer (7) is still noted (see Figure 8). Evidence for the competing disproportionation mechanism is again provided by the presence of peaks proposed to be from unsaturated (8) and saturated (9) end-functionalised oligomer [10]. The data indicate that this disproportionation reaction is a minor termination pathway, as low intensity peaks are noted for 8 and 9 (as for 4 & 5 from the brominated analogue).
Chain End Characterisation
181
6 Theoretical Isotope Distribution
6
100
7*
7 %
89 1490
1500
m/z
1510
0 1480
1490
1500
1510
1520
1530
1540
1550
1560
1570
m/z
Figure 8 Partial MALDI-TOF spectrum from PMMA generated by ATRP with p-toluene sulfonyl chloride as initiator (inset shows theoretical isotope distribution for lithiated 13-mer of 6). (Peak labelled 7 arises from post-source decay of 7 [10].)
Additional evidence for the structures of end groups from many free radical polymers, including styrenes [13–15] and methacrylates [15–18], can be obtained by MS/MS. This technique was employed to generate end group information from the chlorinated PMMA sample. Selection of an individual oligomer enables data to be obtained on one end group functionality. In this case, a lithiated oligomer (11-mer at m/z 1297.6) from the major component in the sample (i.e., 6) was selected for characterisation by MS/MS and the resulting spectrum is displayed in Figure 9 [10]. Previous data from methacrylates demonstrated that two major series of fragment ion peaks were observed in the MS/MS spectra, at low mass-to-charge ratios, that could be employed to generate information about the end group structures [17,18]. Two series of peaks, labelled A and B in Figure 9, indicate that the proposed end group structures for the chlorinated oligomer are as expected, i.e., tosyl and chloride groups as the initiating (a) and terminating (o) end groups, respectively. Peaks at m/z 128 and 228 (see fragmentation scheme in Figure 9) from the A series indicate that the chloride end group functionality is present in this oligomer. The other series (B), with peaks at m/z 262 and 362, is indicative of the presence of the tosyl group as
182
Anthony T. Jackson and Duncan F. Robertson
Relative Intensity (%)
100 95 90 85 80 75 70 65 60 55 50 45 40 35 30 25 20 15 10 5 0
[M + Na – CH3Cl]+ B Series (+Li+) 262 362
G S O
CH2
C CH2
O C
C C H2
O C
OCH3
G
H3C
H3C
H3C
O H3C
A Series (+Li+) 228 128
C CH2
O C
OCH3
7
CH3
CH3
C CH2
C Cl
O C
OCH3
O C
OCH3
OCH3
A B
A
O
CH3 S CH2 C Cl
B Li
H3C
O
O C
11
+
OCH3
100
200
300
400
500
600
700 m/z
800
900
1000 1100 1200
Figure 9 MS/MS spectrum from lithiated 11-mer of PMMA generated by ATRP with p-toluene sulfonyl chloride as initiator (i.e., 6). Proposed fragmentation scheme is shown for assignment of peaks from the A and B series, indicating how end group information may be gleaned.
the initiating functionality. The peaks from each series are separated by a massto-charge ratio (m/z) equivalent to the mass of the repeat unit of the polymer (i.e., 100 Da). The residual mass, after subtracting the mass of a number of (whole or partial) repeat units and the mass of the cation from the mass-to-charge ratio of the fragment ions, is the mass of the end group [17,18]. Peaks labelled G are from internal cleavages and do not aid identification of end group structure. The above data demonstrate how a combination of analytical techniques can be employed to generate end group information from polymers generated by a free radical polymerisation mechanism. In the example described, the use of ESI-MS might have provided more information on the presence of bromide end groups [19,20], as these polymers do not fragment when this technique is used. MS is a particularly powerful complementary technique for characterising the end groups of free radical polymers, as end group composition can be hidden by more intense backbone resonances and hence is not always clearly observed in NMR data.
3. END GROUPS IN CONDENSATION POLYMERS Another important area of polymer chemistry for which end group analysis is often sought is in the polyester industry. This section will attempt to describe
Chain End Characterisation
183
methods that have been used to determine end group concentrations in polyesters, using PET as the main focus, given it is the best known of the aromatic polyesters. Many valid methodologies will be described, or referenced, before concentrating on the particular methodologies used more recently in our own laboratories. Over the past 25 years or so, synthetic polymeric materials have played a significant role in enhancing the ability to package materials (especially foodstuffs) in a safe and convenient manner that is appreciated by both the retailer and the consumer. PET polymers have played a major role in this area, with significant developments in high barrier containers for carbonated soft drinks, high-strength films, excellent gas barrier packaging for sensitive foodstuffs and materials of high clarity. Other significant factors that have played a part in this growth are the portability, lightweight nature and recyclability of PET. It is also a strong, tough, flexible thermoplastic that readily crystallises and can be oriented into highly ordered structures. PET is a polycondensation polymer based on the reaction of terephthalic acid (TA) and mono-ethylene glycol (MEG) or alternatively with di-methyl terephthalate (DMT) plus MEG (Figure 10). For preparing PET polymer for applications such as carbonated soft drinks bottles, the PET polymerisation is a two stage process involving the formation of a base polymer first at approximately 2901C and then a solid-state polymerisation (SSP) stage from which preforms are made. End group determination is of great importance in the characterisation of PET, as end group concentration is an important consideration for making a successful resin choice that will satisfy specific customer needs. Carboxyl and hydroxyl are typically the two major end groups in PET. Establishing an understanding and control of the end group balance is important in controlling both the manufacturing process, especially the SSP reaction, and also the downstream processing. Indeed, the high lateral spatial resolution available with FTIR microscopy was used to highlight differences between hydroxyl and carboxyl end group concentrations between the edges and centres of sections microtomed from a series of PET granules taken from various stages within a solid-phase polymerisation cycle. In the reported study, significant concentration differences were observed for the two positions following the SSP step [1,21]. The carboxyl end is known to catalyse both the polymerisation and hydrolysis reactions. The level of each is process dependant, with the ester interchange process tending to give the lowest carboxyl level in the final product. Some of the possible end groups in PET, along with their mechanisms of formation, are shown below in Figure 11. The carboxyl end can also thermally degrade to form vinyl end groups [22–24], which occur along with the formation of acetaldehyde (Figure 11). This is a side reaction that needs to be avoided, as acetaldehyde can taint mineral water and carbonated soft drinks if present at high levels (W20 ppm) in the bottle polymer. Hence lower temperatures (around 1601C) are used in the SSP phase to minimise the formation of acetaldehyde. Several techniques for determination of end group structure in polyesters have been described in the literature [25–31]. Many analytical procedures have
184
O n H3COC
O COH + n +1 HOCH2CH2OH
O COCH3 + n +1 HOCH2CH2OH
O
- n+1 H2O
O
HOCH2CH2O(C
- n+1 CH3OH
COCH2CH2O)nH
O HOCH2CH2O(C
O COCH2CH2O)nH
Figure 10 Reaction schemes for formation of PET from terephthalic acid and ethylene glycol (top) and di-methyl terephthalate and ethylene glycol (bottom).
Anthony T. Jackson and Duncan F. Robertson
O n HOC
Chain End Characterisation
185
been used, in particular, for the calculation of carboxyl end group concentration. These include acidimetric titration, potentiometric titration and radiochemical determination. Chemical treatment is part of the initial procedure in all of these cases, which in itself gives an advantage to the spectroscopic techniques where no pre-treatment is necessary. The procedure proposed by Campanelli and co-workers [32], for example, was based on potentiometric titrations using ethanolic potassium hydroxide, with the hydrolysed sample dissolved in one of two solvent systems dependent on the extent of hydrolysis. A mixture of di-methylphenol and chloroform, suitable for solubilising the polymers as well as high molecular weight oligomers, was used for calculation of carboxyl group concentrations up to about 1.5 meq carboxyl groups per gram of sample. Di-methylsulfoxide was used as solvent for polymers with higher carboxyl group concentration and for dissolution of TA monomer. Ward and Patterson [33–35] introduced the use of infrared spectroscopy for end group determination in the late 1950s. This technique was based on measurement of absorption bands that characterise the considered end groups, on the assumption that the carboxyl and hydroxyl units were the only end groups in PET. Comparison of the spectrum before and after deuteration of the sample enabled confirmation of the assignments and calculation of Beer–Lambert absorption coefficients for those end groups. FTIR spectra, showing the region of interest (4000–1800 cm1) for the measurement of end groups in PET, are shown below (Figure 12). These are FTIR transmission spectra of PET, prepared as an amorphous pressed film from the melt (approximately 0.1 mm thick), before and after drying the PET film under vacuum. The absorption band due to hydroxyl end groups is clearly evident at approximately 3,542 cm1; the broad absorption due to carboxyl end groups has a band maximum approximately 3,256 cm1 but is overlapped by other PET absorption bands. The end group concentrations can be calculated from their FTIR absorption spectrum using the Beer–Lambert Law. The original calibration of the IR absorption versus end groups was based on measurement of the deuterium content of the water obtained from combustion of deuterated PET polymer assuming that only carboxyl and hydroxyl end groups were present. Later calibrations were based on measurements of standards generated from model compounds [36]. In the original work of Ward and Patterson a comparison (absorbance subtraction) was made between the IR spectra recorded from protonated and deuterated spectra of amorphous PET film samples; this aided establishing the peak position maximum positions of the –OH and –COOH bands and defining background absorption levels for their concentration determinations; the –OD and –COOD band maximum occur at 2,604 cm1 and 2,458 cm1, respectively [37]. A simple conversion for PET gives (in the case of acid ends): ½COOH ¼ Corr:AbsCOOH 104 =plCOOH where [COOH] is the concentration of carboxylate groups in g equiv./106 g polymer, p the sample density in g cm3, l the film thickness in cm, Corr.AbsCOOH
186
O
O
O
COCH2CH2OC
O
C-
-C
COCH2CH2OH
-C
O
O
-C
O
O
-C
O -C
O -C
Figure 11
O
COCH CH2
+
O
-C
+
HOCH2CH2OH
-C
+
HOCH2CH2OH
-C
O
O
O COCH2CH2OH
O
COCH2CH2OH
-C
COCH2CH2OH
O
O
O
O
COCH CH2
+
O
O
COH
+
O
O
-C
COH
H3CCH
O
COCH2CH2OC
O
O COCH2CH2OCH2CH2OH + H2O
O COH
+
Reaction schemes for formation of PET oligomers with different end group structures.
O
C- + H3CCH
HOCH2CH2OCH2CH2OH
Anthony T. Jackson and Duncan F. Robertson
O -C
Chain End Characterisation
Absorbance
-OH end group ~3542 cm-1
-COOH end group ~3256 cm-1
187
PET containing absorbed water
Absorbed water
Vacuum dried PET
4000
3500
3000 Wavenumber /cm-1
2500
2000
Figure 12 Expansion (4000–1800 cm1) of absorbance FTIR spectra recorded from a PET film, before and after drying.
the absorbance of carboxyl ends corrected for background absorbance of PET with no COOH end groups and eCOOH the band aborptivity. FTIR spectroscopy has been found to be a reliable technique for end group determination in PET and shows good agreement with results from titration and 1 H NMR measurements. The absorbance bands from carboxyl and hydroxyl end groups have been shown to interfere to some extent. A simultaneous curve fitting procedure has been developed, in recent years, to separate the two peaks, in order to give more representative values for the respective end group measurements [38]. (The IR method of Ward and Patterson [34,35] has been adapted for determining the end group concentrations in poly(butylene terephthalate) [39] and poly(ethylene naphthalene-2,6-dicarboxylate [40].) Early work on polyester end group analysis by NMR spectroscopy was carried out by Page and Bresler [41]. They used the labile protons in the hydroxyl groups of both the carboxylate and hydroxyl end groups. As these labile protons are by nature broad resonances in the proton NMR spectrum other methodologies have been developed over the years to better measure these end groups. The advantage of using NMR for these measurements is that NMR is an inherently quantitative technique, in that line intensity, or the area under each signal, in the spectrum is proportional to the number of hydrogen (or other observed nucleus) atoms in that group. Measurement of the peak area is carried out by integration. NMR-based techniques also offer the advantages of relatively small sample requirement and the measurements being quick and reliable. One of the issues in using solution state NMR for PET analysis is that, due to the high crystallinity content of the polymer, it is fairly difficult to dissolve. Harsh
188
Anthony T. Jackson and Duncan F. Robertson
solvents are required; some examples of which are 3-chlorophenol, 1,1,1,3,3,3hexaflouro-2-propanol (HFIP) and trichloroacetic acid or trifluoroacetic acid. We prefer to use 1,1,2,2-tetrachloroethane-d2 (TCE) in our laboratory. Experiments need to be performed at elevated temperatures (100–1201C) to keep the sample in solution (in TCE). The spectra displayed below show how this solvent can be used to obtain appropriate NMR resonances from PET that can be used to detect and quantify the end groups of the polyester. Figure 13 shows a full 1H NMR spectrum of PET, in TCE solvent, acquired at 1001C. Resonances a and b are from the terephthalate and ethylene glycol derived protons, respectively. Resonances c and d arise from the protons in diethylene glycol (DEG), which is formed as a side reaction in the PET polymerisation process. An expansion of the ethylene glycol-based region of the spectrum is shown in Figure 14. Proton NMR techniques have been described for characterising end groups [42–44], the methodology below being that which is used in our laboratory. Resonances e and f in Figure 14 arise from the hydroxyl end group in PET. Integration of resonance f versus resonance b (or the resonance from the
O
a
a
-(C a
a
O
O b b COCH2CH2O)x - (C
a
a
O
c d d c COCH2CH2OCH2CH2O)y-
a
a
a
b
c
d
9.5 9.0 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 Chemical Shift (ppm)
Figure 13
1
H NMR spectrum of PET in TCE solvent.
0
189
Chain End Characterisation
b O -C
O
e f COCH2CH2OH
c d
e f
5.0
4.9
4.8
4.7
4.6
4.5
4.4
4.3 4.2 4.1 4.0 Chemical Shift (ppm)
3.9
3.8
3.7
3.6
3.5
Figure 14 Expansion (3.50–5.02 ppm) of ethylene glycol region of 1H NMR spectrum of PET.
terephthalate moiety) gives a direct measure of the number of hydroxyl end groups present relative to the number of polymer repeat units. The number of these end groups per 100 polymer repeat units can be calculated, for example, if the integral of resonance b is set to 400 and the integral of resonance f is divided by 2 (because it is a resonance from –CH2OH). Figure 15 shows this same expanded region when di-methyl terephthalate is used as the monomer. The only difference is the sharp single peak labelled g, which arises from residual methyl ester end groups. This resonance sits on top of the triplet arising from the –CH2OH (f) end (at 400 MHz) and, therefore, deconvolution software is used to measure these residual methyl ester ends. Acquiring data at room temperature is probably most important for the carboxylate end measurement, as any polymer degradation at elevated temperature could form additional acid end groups. As an example of NMR methodology that is not carried out in TCE, consider the following for the measurement of carboxylate ends in polyesters. The sample is dissolved in a mixture of HFIP and trichloromethane and spectra are acquired at room temperature (see, e.g., Figure 16). Dissolution in HFIP causes the carboxylate end groups to become functionalised and form an aromatic secondary carbon ester [45,46] as shown in Figure 17. A mediated reaction is required to enable a rapid esterification of the acid end groups at room temperature, hence avoiding generation of additional acid end
190
Anthony T. Jackson and Duncan F. Robertson
b
c
e
d O -C
O
g COCH3
f
5.1
5.0
4.9
4.8
4.7
4.6 4.5 4.4 4.3 4.2 Chemical Shift (ppm)
4.1
4.0
g
3.9
3.8
3.7
3.6
Figure 15 Expansion (3.60–5.20 ppm) of ethylene glycol region of the 1H NMR spectrum of PET, when di-methyl terephthalate has been used as the monomer.
groups. Resonances at 6.3 and 6.7 ppm in the 1H NMR spectrum (Figure 16) can hence be ignored in end group calculations, as these occur due the mediators added and the resultant side reactions. Resonance h (6.0 ppm) occurs from the hexafluoro ester (from the derivatised acid end group of the PET) and this can be quantified against the polymer chain (resonance a) in a similar way to that described previously. Fluorine (19F) NMR can also be used for this end group measurement [47], as the reaction involves formation of a fluoro ester. The formation of vinyl end groups has been mentioned previously as an undesirable side reaction in the PET polymerisation process. It is important to be able to measure these end groups, as acetaldehyde is evolved during formation of this moiety, which can cause taint in carbonated soft drink applications. Figure 18 shows a spectrum obtained in TCE at 1001C, showing a resonance from the vinyl end group that can be quantified relative to the polymer backbone. This resonance is usually very low in intensity and difficult to measure accurately. One way of enhancing this resonance is to set the decoupler in the 1 H NMR experiment to be on top of the other half of the vinyl end resonance. This has the effect of collapsing the multiplicity of the resonance shown (i in Figure 18) and hence increasing the intensity above the noise in the spectrum. We then find it preferable, in our laboratory, to use a peak height measurement
191
Chain End Characterisation
a
O
O
h COCH(CF3)2
-C
h
8.5
8.0
7.5
7.0
6.5
6.0
Chemical Shift (ppm)
Figure 16 Expansion (5.80–8.65 ppm) of 1H NMR spectrum of PET, showing acid end groups.
O -C
O COH
O + HOCH(CF3)2
-C
O COCH(CF3)2 + H2O
Figure 17 Reaction scheme for conversion of acid ends to esters by addition of 1,1,1,3,3,3hexaflouro-2-propanol (HFIP).
method rather than integration (as the integration is very difficult to carry out accurately, due to the vast differences in the intensities of the two resonances that are being compared). Although this methodology may not be very accurate in absolute terms, it is repeatable and, in an industrial laboratory, a method that is able to measure and compare these end group levels in some way is essential. There are many other methodologies that can be used to measure end groups of polyesters by NMR. The examples above represent methods that we are using in our own work. Another powerful analytical technique for measurement of end groups in polymers is MALDI-TOF MS. The advantage of this technique is that information on individual oligomers can be obtained. Detection of higher molecular weight cyclic oligomers (i.e., those with no end groups) is also possible [48], unlike by means of NMR spectroscopy and FTIR spectroscopy. Direct quantification of end group levels, from the MALDI-TOF MS data, is difficult due to the likely
192
Anthony T. Jackson and Duncan F. Robertson
b
O
d
c
O
i COCH CH2
-C
e
f
i
5.2
Figure 18
1
5.1
5.0
4.9
4.8
4.7 4.6 4.5 4.4 4.3 Chemical Shift (ppm)
4.2
4.1
4.0
3.9
3.8
3.7
H NMR spectrum of PET showing a vinyl end group resonance.
ionisation efficiency differences for oligomers with hydroxyl and carboxylate ends. Relative levels of end groups (and cyclic oligomer) in multiple samples can be visualised from the data. The presence of hydroxyl and carboxyl end groups can be discerned from the data, with differentiation between oligomers containing zero, one and two acid end groups. One issue with end group interpretation is the isobaric nature of oligomer containing two hydroxyl ends with that containing one acid end and one hydroxyl end group with one diethylene glycol (DEG) unit in-chain. The presence or lack of carboxylate salt ends, however, (derived from the cation used in the MALDI-TOF MS experiment, as shown below) can be employed to differentiate between these two species. So, for example, if a lithium salt is used as the cationisation agent, the following reaction occurs (to partially convert some of the acid ends to carboxylate salt): CO2 H þ Liþ ! CO2 Li þ Hþ An example (partial) spectrum, indicating how end group information can be gleaned by MALDI-TOF MS, is shown in Figure 19. Peaks are annotated with numbers corresponding to those for the proposed structures of the oligomers present in this low molecular weight sample of PET. Cyclic oligomers (structures 10–12), including those containing DEG units (11 with one unit of DEG and 12 with two units). Linear oligomers (structures 13–17) are also clearly present in the sample, including hydroxyl functionalised material (13–15) and lower levels with acid end groups (16–17). Linear oligomer containing DEG units can clearly be
193
Chain End Characterisation
100 10 10
13
11 16
%
14
17′′
16′
17 15
12 950
0 500
750
1000
1250
1500
1750
1000
2000 m/z
1050 m/z
2250
1100
2500
2750
1150
3000
3250
Figure 19 MALDI-TOF mass spectrum from low molecular weight PET sample. Inset shows expansion of MALDI-TOF spectrum from m/z 950–1170, with peaks annotated with numbers corresponding to proposed assignments (see text for assignments).
discerned (e.g., 14 which is hydroxyl ended oligomer with one DEG unit). Confirmation of the presence of acid functionalised material from conversion of these end groups to carboxylate salt in the MALDI experiment (as described above) is possible from peaks annotated as 16u and 17uu in Figure 19. Conversion of the one acid end group in oligomer 16 to carboxylate salt gives rise to peak 16u. In addition, 17uu is derived from conversion of the two acid end groups in 17 to lithium carboxylate. TE
TE
n
10
HOE
TE
n
n
TEE
11
H
HOE TE
13
n
TE
n
H
16
n
TEE
2
12
TEE H
HOE
1
14
HO
T =
TE
1
TE
n
TEE H
15
HO
TE
n
TH
17
O
O
C
CO
E =
CH2CH2O
2
194
Anthony T. Jackson and Duncan F. Robertson
4. END GROUPS IN POLYMERS FROM IONIC POLYMERISATION There are a number of commercially important synthetic polymers produced by cationic [49,50] or anionic polymerisation [51,52] routes. An example is shown in Figure 20 for poly(propylene glycol) (PPG), which is a polymer commonly used as the soft segment in polyurethane polymers. PPG is produced by the anionic ring-opening polymerisation of propylene oxide [53], as described by the reaction scheme shown in Figure 20, with an alcohol (ROH) as initiator and a base such as potassium hydroxide (therefore M is typically K) as catalyst. Alcohols such as water (R is –H) or di-propylene glycol (R is –OCH(CH3)CH2OCH2CH(CH3)OH) can be used as initiators, in order to produce di-hydroxyl end-capped PPG (structure 18). Chain transfer can result in formation of impurities in the desired end group functionality, as shown in Figure 20 for formation of allyl-initiated PPG (structure 19). This impurity is typically more prevalent in PPG polymers of higher average molecular weight. It results from ring opening of propylene oxide to form a derivative of allyl alcohol (H2CQCHCH2OM+) that reacts with further units of propylene oxide to form oligomers. Isomerisation of allyl end groups can result in the formation of isopropenyl end functionality, as described in Figure 20. HO CH2CHO H
H2C
n
CHCH2O CH2CHO H n
CH3
CH3
18
19
Initiation RO-M+ + P
→
ROP-M+
Propagation ROP-M+ + Pn
→
ROPnP-M+
Termination ROPnP-M+ + ROH
→
ROPn+1H + RO-M+
Chain Transfer P + RO-M+ H2C=CHCH2O-M+ + P H2C=CHCH2OP-M+ + Pn
→ →
Isomerisation H2C=CHCH2OM+ H3CCH=CHO-M+ + P H3CCH=CHOP-M+ + Pn
→ →
→
→
H2C=CHCH2O-M+ + ROH H2C=CHCH2OP-M+ H2C=CHCH2OPnP-M+
Allyl
H3CCH=CHOM+ H3CCH=CHOP-M+ H3CCH=CHOPnP-M+
Isopropenyl
Figure 20 Reaction scheme for the anionic polymerisation of propylene oxide to form PPG (R is the part of alcohol initiator, M the metal from the catalyst and P the propylene oxide).
195
Chain End Characterisation
Di-hydroxyl end-capped PPG (18) is an intermediate in the formation of a common polyurethane prepolymer (20). End group functionality of this intermediate is important, as this hydroxyl functionality is modified to form the prepolymer. Any different end group structures could lead to the presence of prepolymer that will not form polyurethane of the desired structure. The desired reaction of the intermediate (18) to form the prepolymer (20) is described in Figure 21. Reaction of one unit of the intermediate (18) and two units of methylene diphenyl 4,4u-diisocyanate (MDI) results in the formation (nominally) of the prepolymer (20). O O C N
CH2
O
NHCO CH2CHO CNH
CH2
n
N C O
CH3
20 O H2C
CHCH2O CH2CHO CNH
CH2
n
N C O
CH3
21
O
O
OCNPhCH2Ph [NHCO(CH2CHO)nCONHPhCH2Ph]x NCO CH3 22
A combination of NMR spectroscopy and MALDI-TOF MS is commonly employed in our laboratory for the characterisation of PPG polymers. Analysis of di-hydroxyl end-capped PPG (18) is initially described. The 1H NMR spectrum [54] can be used to confirm the backbone structure of the polymer, as can be seen in Figure 22 (a and b are from the backbone of the polymer, with c from the methyl side chains). Peaks of low intensity, downfield of those from the backbone of the polymer, in the 1H NMR spectrum may be used to identify and quantify the allyl functionality in the polymer [55]. These resonances (d, e and f) are
HO CH2CHO H n
+
2O
C N
CH2
N C O
CH3 PPG
MDI
O
O O C N
CH2
NHCO CH2CHO CNH n
CH2
N C
CH3 Prepolymer
Figure 21 Reaction scheme for the reaction of PPG with MDI to form a polyurethane prepolymer.
O
196
Anthony T. Jackson and Duncan F. Robertson
d e f H2C CHCH2O CH2CHO d
e
n
f
c
CH3
6.0 5.9 5.8 5.7 5.6 5.5 5.4 5.3 5.2 5.1 5.0 4.9 4.8 4.7 4.6 4.5 4.4 4.3 4.2 4.1 4.0 Chemical Shift (ppm)
a&b
a b CH2CHO
n
CH3 c
6.5
6.0
5.5
5.0
4.5
4.0 3.5 3.0 2.5 Chemical Shift (ppm)
2.0
1.5
1.0
0.5
Figure 22 1H NMR spectrum from di-hydroxyl end-capped PPG. Inset shows expansion of spectrum indicating assignments for allyl end groups of polymer.
annotated in the expansion of the 1H NMR spectrum shown in Figure 22, along with a structure indicating the protons giving rise to these peaks. End group isomerisation of allyl end groups to isopropenyl ended species (i.e., as shown in Figure 20) can be followed, in solution, using 1H NMR, as is shown in Figure 23 [56]. Gradual conversion of polymer containing allyl ends (Figure 23(a), 0 h) to all isopropenyl ends (Figure 23(c), 594 h) can be visualised by resonances from the unsaturated portions of the end group functionalities. A spectrum taken at an intermediate time (Figure 23(b), 89 h) shows a mixture of both allyl and isopropenyl functionality is present. Proposed assignments of the resonances from these two end group functionalities are shown in Figure 23(a) (allyl) and Figure 23(c) (isopropenyl). The presence of hydroxyl end groups in PPG can be assigned from 13C NMR data (Figure 24), with resonances (g) observed between 65–68 ppm in the spectrum shown in Figure 24. There are two different resonances here (g) due tacticity effects in the polymer (meso/racemic (m/r) isomerisation of the terminal dyad). Estimations of the amount of these ends in the polymer, along with the average molecular weight of the PPG, can be made from the 13C NMR data. Confirmation of the presence of allyl and hydroxyl functionality in PPG polymers can be gleaned from MALDI-TOF MS data. An example spectrum for a sample of PPG 2000 is shown in Figure 25. These data can be used to generate information about both the end groups and the average molecular weight [57].
Chain End Characterisation
197
Figure 23 Monitoring of isomerisation of allyl end groups of PPG to isopropenyl functionality over time by means of 1H NMR spectroscopy: (a) 0 h, (b) 89 h and (c) 594 h. Reproduced from Ref. [56] with permission of John Wiley & Sons, Inc.
The major distribution, centred at approximately 2000 Da as expected, can be assigned as from di-hydroxyl end-capped oligomers of PPG (18). Addition of lithium salts in the MALDI sample preparation procedure leads to the generation of [18 + Li]+ ions as the major species. A series of low-intensity peaks below
198
Anthony T. Jackson and Duncan F. Robertson
g CH2CHO CH2CHOH n CH3 CH3
g
78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 Chemical Shift (ppm)
80
75
70
65
60
55 50 45 40 Chemical Shift (ppm)
35
30
25
20
15
Figure 24 13C NMR spectrum from di-hydroxyl end-capped PPG. Inset shows expansion of spectrum indicating assignments for hydroxyl end groups of polymer.
18
100
%
19
0 1000
1500
2000
2500 m/z
3000
3500
Figure 25 MALDI-TOF mass spectrum from di-hydroxyl end-capped PPG, indicating the presence of hydroxyl and allyl end-capped oligomers (see text for description of peak annotation).
199
Chain End Characterisation
O
h CH2
CH2CHO CNH n CH3
N C O
h
3.95
7.5
7.0
6.5
6.0
3.90 3.85 Chemical Shift (ppm)
5.5
5.0 4.5 4.0 3.5 Chemical Shift (ppm)
3.0
2.5
2.0
1.5
1.0
Figure 26 1H NMR spectrum from MDI/PPG polyurethane prepolymer. Inset shows expansion of spectrum indicating assignment for functionalised end groups of polymer.
approximately m/z 1,600 arise from the presence of oligomers containing an allyl group and a hydroxyl functionality (19). The presence of these latter oligomers at lower average molecular weights is expected from knowledge of the chemistry, but MS is the only way of demonstrating this. It is not possible, however, to easily distinguish allyl and isopropenyl functionality using MS, due to the isobaric (and isomeric) nature of the two species. However, NMR easily distinguishes these two moieties, as described above. NMR spectra (1H in Figure 26 and 13C in Figure 27) from polyurethane prepolymer, formed by the reaction described in Figure 21, indicate that the desired product has been made [58]. Singlets (h at 3.87 ppm in the 1H spectrum, Figure 26, and i at 40.7 ppm in the 13C spectrum, Figure 27) in the spectra indicate that the hydroxyl functionality has been modified by MDI units to form the desired product with isocyanate end groups. Residual levels of hydroxyl end groups can be detected from 13C NMR data, to give an indication of the degree of functionalisation. Allyl end groups should not be modified in the end-capping reaction and hence can still be detected in the 1H NMR spectrum. Furthermore, it is also possible to detect other functionalities from these data. Confirmation of the modification of the hydroxyl end groups from the PPG can be accomplished by analysis using MALDI-TOF MS [59]. An example MALDI-TOF mass spectrum of a prepolymer based on PPG 2000 is shown in Figure 28. End group and average molecular weight data can be gleaned from the spectrum. The dominant distribution of peaks centred at approximately m/z 2,500
200
Anthony T. Jackson and Duncan F. Robertson
O
i CH2
CH2CHO CNH n CH3
N C O
i
41.0
40.5 Chemical Shift (ppm)
152 144 136 128 120 112 104 96 88 80 72 64 Chemical Shift (ppm)
56
48
40
32
24
16
8
Figure 27 13C NMR spectrum from MDI/PPG polyurethane prepolymer. Inset shows expansion of spectrum indicating assignment for functionalised end groups of polymer. 20
100
% 21 22 x =2 22 x =3
22 x =4
0 1000
2000
3000
4000
5000 6000 m/z
7000
8000
9000
Figure 28 MALDI-TOF mass spectrum from MDI/PPG polyurethane prepolymer. Peaks from functionalised oligomers are annotated with numbers corresponding to those described in the text.
Chain End Characterisation
201
indicates that the desired product (20) has been formed. Chain-extended oligomer (22) can be detected, which contains MDI units with both isocyanate groups reacted with hydroxyls to form urethane bonds. Reaction of oligomers from the PPG 2000 that contained allyl functionality with MDI leads to the formation of 21. The presence of these species is confirmed by the series of peaks (annotated as 21 in Figure 28) seen below m/z 1,500. The presence of other, minor, end group functionalities can also be detected by MALDI-TOF MS. The combination of NMR and MALDI-TOF MS data again gives both complementary and confirmatory evidence for the presence of differing end group functionalities in these polymers. The synergy of these two techniques is very important for the analysis of end groups in alkoxylates. Characterisation using only one of these two techniques can lead to either wrong assignments or certain end group functionalities not being detected. Isomeric content, for example, can be missed by only employing MALDI-TOF MS.
5. CLOSING REMARKS Although this chapter has focused essentially on three examples that highlight the synergy between NMR spectroscopy and MS for characterising end groups, and the complementary role of FTIR spectroscopy to some solid-state characterisations, particularly from a viewpoint of product research and development, we are aware that there are other studies and methods used for characterising and quantifying end group levels in organic polymers. For instance, near-infrared (NIR) spectroscopy, while not used as a tool to characterise polymer end group functionality, has been used for both product composition quality assurance and process control for end group concentrations. Other examples of applications of mid-infrared to end group measurements may be found in two recent publications [60,61].
ACKNOWLEDGEMENTS Dr Neil Everall, Ian Priestnall and Malcolm Beckett (all Intertek MSG, Wilton, Redcar, UK) are thanked for useful discussions and help with preparation of the manuscript. The authors would like to thank AkzoNobel (ATJ) and Intertek MSG (DFR) for permission to publish the work.
REFERENCES 1 J.M. Chalmers and N.J. Everall, Macromol. Symp., 94 (1995) 33–49. 2 B.B. Kine and R.W. Novak, Acrylic and methacrylic ester polymers. In: J.I. Kroschwitz (Ed.), Encyclopedia of Polymer Science and Engineering, Wiley, Chichester, 1985, pp. 234–299. 3 K. Matyjaszewski (Ed.), Controlled/Living Radical Polymerisation, American Chemical Society, Washington, DC, 2000. 4 M.K. Georges, R.P.N. Veregin, P.M. Kazmaier and G.K. Hamer, Trends Polym. Sci., 2 (1994) 66–72. 5 T.E. Patten, J. Xia, T. Abernathy and K. Matyjaszewski, Science, 272 (1996) 866–868.
202
Anthony T. Jackson and Duncan F. Robertson
6 J.S. Wang and K. Matyjaszewski, J. Am. Chem. Soc., 117 (1995) 5614–5615. 7 J. Chiefari, Y.K. Chong, F. Ercole, J. Krstina, J. Jeffery, T.P.T. Le, R.T.A. Mayadunne, G.F. Meijs, C.L. Moad, G. Moad, E. Rizzardo and S.H. Thang, Macromolecules, 31 (1998) 5559–5562. 8 C. Barner-Kowollik, T.P. Davis and M.H. Stenzel, Polymer, 45 (2004) 7791–7805. 9 K. Matyjaszewski and J. Xia, Chem. Rev., 101 (2001) 2921–2990. 10 A.T. Jackson, A. Bunn, I.M. Priestnall, C.D. Borman and D.J. Irvine, Polymer, 47 (2006) 1044–1054. 11 C.D. Borman, A.L. Cutter, D.J. Irvine, A.T. Jackson and A. Bunn, Polymer, 41 (2000) 6015–6020. 12 G. Socrates, Infrared and Raman Characteristic Group Frequencies: Tables and Charts, 3rd ed., Wiley, Chichester, 2001, p. 142. 13 A.T. Jackson, A. Bunn, L.R. Hutchings, F.T. Kiff, R.W. Richards, J. Williams, M.R. Green and R.H. Bateman, Polymer, 41 (2000) 7437–7450. 14 A.T. Jackson, H.T. Yates, J.H. Scrivens, M.R. Green and R.H. Bateman, J. Am. Soc. Mass Spectrom., 9 (1998) 269–274. 15 J.H. Scrivens, A.T. Jackson, H.T. Yates, M.R. Green, G. Critchley, J. Brown, R.H. Bateman, M.T. Bowers and J. Gidden, Int. J. Mass Spectrom., 165–166 (1997) 363–375. 16 J. Gidden, M.T. Bowers, A.T. Jackson and J.H. Scrivens, Int. J. Mass Spectrom., 188 (1999) 121–130. 17 A.T. Jackson, H.T. Yates, J.H. Scrivens, M.R. Green and R.H. Bateman, J. Am. Soc. Mass Spectrom., 8 (1997) 1206–1213. 18 A.T. Jackson, H.T. Yates, J.H. Scrivens, G. Critchley, J. Brown, M.R. Green and R.H. Bateman, Rapid Commun. Mass Spectrom., 10 (1996) 1668–1674. 19 C.N. McEwen, P.M. Peacock and Z. Guan, Proceedings of the 45th ASMS Conference on Mass Spectrometry and Allied Topics, Palm Springs, CA, June 1–5, 1997; p. 409. 20 H.Q. Zhang, X.L. Jiang and R. van der Linde, Polymer, 45 (2004) 1455–1466. 21 J.M. Chalmers and N.J. Everall, Int. J. Polym. Anal. Charact., 5 (1999) 223–245. 22 E.P. Goodings, Soc. Chem. Ind. (London) Monograph, 13 (1961) 211. 23 R.J.P. Allan, H.V.R. Lengar and P.D. Ritchie, J. Chem. Soc. (1957) 2107–2113. 24 I. Marshall and A. Todd, Trans. Faraday Soc., 49 (1953) 67–78. 25 K. Weisskopf, J. Polym. Sci., Part A: Polym. Chem., 26 (1988) 1919–1935. 26 G.D.B. Van Houwelingen, Analyst, 106 (1981) 1057–1070. 27 J. Ubranski, W. Czerwinski, K. Janicka, F. Majewska and H. Zowell, In: G.G. Cameron (Ed.), Handbook of Analysis of Synthetic Polymers and Plastics, 1st ed., Halsted Press, London, 1977, pp. 223–272. 28 R.L.M. Van Lingen, Z. Anal. Chem., 247 (1969) 232. 29 A. Conix, Makromol. Chem., 103 (1967) 19. 30 G.F. Price, In: P.W. Allen (Ed.), Techniques of Polymer Characterisation, Butterworths Scientific, London, 1959, pp. 209–229. 31 H.A. Pohl, Anal. Chem., 26 (1954) 1614–1616. 32 J.R. Campanelli, M.R. Kamal and D.G. Cooper, J. Appl. Polym. Sci., 48 (1993) 443–451. 33 I.M. Ward, Nature, 180 (1957) 141. 34 I.M. Ward, Trans. Faraday Soc., 53 (1957) 1406–1412. 35 D. Patterson and I.M. Ward, Trans. Faraday Soc., 53 (1957) 291–294. 36 R.L. Addleman and V.J.I. Zichy, Polymer, 13 (1972) 391–398. 37 J.M. Chalmers, Spectra-structure correlations: Polymer spectra. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007. 38 S. Al-AbdulRazzak, E.A. Lofgren and S.A. Jabarin, Polym. Int., 51 (2002) 174–182. 39 P.G. Kosky, R.S. McDonald and E.A. Guggenheim, Polym. Eng. Sci., 25 (1985) 389–394. 40 H. Zhang, A. Rankin and I.M. Ward, Polymer, 37 (1996) 1079–1085. 41 T.F. Page, Jr. and W.E. Bresler, Anal. Chem., 36 (1964) 1981–1985. 42 T. Amari, K. Nishimura, K. Minou, A. Kawabata and Y. Ozaki, J. Polym. Sci., Part A: Polym. Chem., 39 (2001) 665–674. 43 A.M. Kenwright, S.K. Peace, R.W. Richards, A. Bunn and W.A. MacDonald, Polymer, 40 (1999) 2035–2040. 44 S. Amiya, K. Mathumura and T. Taniguchi, Anal. Sci., 7 (1991) 1649. 45 P. Barton, A.P. Laws and M.I. Page, J. Chem. Soc., Perkin Trans., 2 (1994) 2021–2030.
Chain End Characterisation
203
46 W.H. Urry, A. Nishihara and J.H.Y. Niu, J. Org. Chem., 32 (1967) 347–352. 47 Y. Ma, U.S. Agarwal, J.A.J.M. Vekemans and D.J. Sikkema, Polymer, 44 (2003) 4429–4434. 48 A.T. Jackson, H.T. Yates, W.A. MacDonald, J.H. Scrivens, G. Critchley, J. Brown, M.J. Deery, K.R. Jennings and C. Brookes, J. Am. Soc. Mass Spectrom., 8 (1997) 132–139. 49 J.P. Kennedy and S. Jacob, Acc. Chem. Res., 31 (1998) 835–841. 50 K. Matyjaszewski (Ed.), Cationic Polymerizations: Mechanisms, Synthesis and Applications, Marcel Dekker, New York, 1996. 51 H.L. Hsieh and R.P. Quirk, Anionic Polymerization: Principles and Practical Applications, Marcel Dekker, New York, 1996. 52 M. Szwarc, Carbanions, Living Polymers and Electron Transfer Processes, Interscience, New York, 1968. 53 R.W. Body and V.L. Kyllingstad, 1,2-Epoxide polymers. In: J.I. Kroschwitz (Ed.), Encyclopedia of Polymer Science and Engineering, Wiley, Chichester, 1986, pp. 225–322. 54 F. Heatley, J.F. Ding, G.E. Yu, C. Booth and T.G. Blease, Makromol. Chem. Rapid Commun., 14 (1993) 819–823. 55 G-E. Yu, A.J. Masters, F. Heatley, C. Booth and T.G. Blease, Macromol. Chem. Phys., 195 (1994) 1517–1538. 56 G.-E. Yu, F. Heatley, C. Booth and T.G. Blease, J. Polym. Sci., Part A: Polym. Chem., 32 (1994) 1131–1135. 57 U. Bahr, A. Deppe, M. Karas, F. Hillenkamp and U. Giessmann, Anal. Chem., 64 (1992) 2866–2869. 58 A.M. Heintz, D.J. Duffy, S.L. Hsu, W. Suen, W. Chu and C.W. Paul, Macromolecules, 36 (2003) 2695–2704. 59 R.H. Carr and A.T. Jackson, Rapid Commun. Mass Spectrom., 12 (1998) 2047–2050. 60 J.M. Chalmers and N.J. Everall, Qualitative and quantitative analysis of plastics, polymers and rubbers by vibrational spectroscopy. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007, pp. 1–67. 61 F.J. Boerio and S. Wirasate, Measurements of the chemical characteristics of polymers and rubbers by vibrational spectroscopy. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007, pp. 113–141.
This page intentionally left blank
CHAPT ER
6 Determination of Molecular Weights and Their Distributions Simone Wiegand and Werner Ko¨hler
Contents
1. Introduction 2. Distribution Functions and Averages 3. Methods Based on Colligative Properties 3.1 Membrane osmometry 3.2 Vapour pressure osmometry 4. Viscometry 5. Scattering Techniques 5.1 Static light scattering 5.2 Dynamic light scattering 5.3 Other scattering methods 6. Liquid Chromatography 6.1 Size-exclusion chromatography 6.2 Field-flow fractionation 7. Analytical Ultracentrifuge 8. Other Methods 8.1 Mass spectrometry 8.2 Nuclear magnetic resonance 8.3 Infrared spectroscopy 8.4 Electrophoresis 9. Practical Examples 9.1 Characterization of rigid-rod polymers 9.2 Scaling laws 10. Conclusion Acknowledgements References
205 208 212 213 215 218 220 220 225 228 228 228 232 235 237 237 239 240 240 241 241 243 247 248 248
1. INTRODUCTION In contrast to biological macromolecules such as proteins, synthetic polymers are, in general, polydisperse. Their molar masses, which show a broad distribution of Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00406-6
r 2008 Elsevier B.V. All rights reserved.
205
206
Simone Wiegand and Werner Ko¨hler
varying width depending on the mode of synthesis, around some average value, directly influence both microscopic parameters, such as molecular diffusion coefficients, and macroscopic material properties, like melt viscosity or brittleness. As a consequence, precise knowledge of the molar mass distribution or, at least, of certain molar mass averages, is of fundamental importance both for basic research on polymeric materials and for their commercial application. Since serious work in polymer science and technology without knowledge of the molar mass appears impossible, its measurement has always been a prime task in polymer analysis and the starting property for any subsequent research. Strictly speaking, the terms molar mass and molecular weight refer to different quantities. Molar mass is the mass of one mole of polymer molecules and measured in g/mol, whereas molecular weight is dimensionless and refers to the weight (mass) of a single polymer molecule measured as multiples of the atomic mass unit u. The numerical values of both quantities are identical. Usually, no such strict distinction is made in the literature, and also in this contribution both terms will be used as synonyms for the strict term molar mass. Experimental methods for determining molar masses, such as viscometry [1,2], have been employed since the early days of polymer science, and the development of new and more powerful techniques and instrumentation, like mass spectrometry or multidimensional chromatography, still continues today. Owing to the diverse nature of polymers, there is no single method available that can provide the complete molar mass distribution function for all macromolecules and cover the entire molar mass range from oligomers to high polymers. In production control a single measurement of, e.g., the intrinsic viscosity, may suffice, but in advanced polymer research only the combined results from a number of different techniques will provide sufficient information in all but the most trivial cases. One can differentiate between absolute methods and those that need a proper calibration. For instance, fractionating techniques like the widely used size exclusion chromatography allow the determination of the molar mass distribution function only under certain assumptions and with proper calibration. Other experimental methods provide a model-free access to specific averages of molecular properties, such as the weight average molar mass or the z-average mean square radius of gyration obtained from static light scattering or the number average molar mass from membrane osmometry. For a correct interpretation of experimental data a precise knowledge of the respective statistical weights and averages is of utmost importance and the relevant definitions will be presented in the first section. In the subsequent sections follows a discussion of different experimental methods and their strengths and limitations. Practical examples taken from the literature are presented for every major experimental method discussed. If available, references to recent review articles or textbooks will be given. As a guide for the reader, Table 1 lists some features of the experimental techniques discussed in this chapter. For each method it is specified whether it allows the determination of an average molar mass and also of the distribution. Estimates of the molar mass range, typical sample amounts and the operating
Table 1 Experimental methods to obtain molecular weight distributions and averages for polymers. For each method it is indicated whether absolute values (a) are obtained or whether a calibration or knowledge of a scaling law (c) are required. The sample amounts listed in the table are typical numbers, which might vary depending on the sample properties and the equipment available. The operating expense covers roughly the cost of equipment and personnel, time for measurement and interpretation. Average
Distribution
M range (g/mol)
Amount/mg
Operating expense
Colligative methods Membrane osmometry Vapour pressure osmometry
Mn (a) Mn (a, c)
– –
104oMo106 Mo5 104
200 200
Low Low
Mw (a) hMn i1=n (c) z
– (c)
MW104 MW5 102
300a 50a
Moderate to high Moderate to high
Liquid chromatography Size exclusion chromatography Field-flow fractionation
Mn, Mw, Mz (c) Mn, Mw, Mz (c)
(c) (c)
Mo107 MW103
10 10
Moderate Moderate
Analytical ultracentrifuge Sedimentation velocity Sedimentation equilibrium
Mn, Mw, Mz (a) Mw, Mz (a)
(a) –
MW103 MW103
100 100
High High
Mass spectrometry MALDI-TOF-MSb Viscometry
Mn, Mw, Mz (a)
(a)c
Mo106
10
High
Ubbelohde viscometer
MZ (c)
–
MW102
150
Low
End group analysis Nuclear magnetic resonance Infrared spectroscopy (IR)
Mn (a) Mn (a)
(a) (a)
Mo3 104 Mo104
10 10
High Moderate
Scattering techniques Static light scattering Dynamic light scattering
Depends on molar mass. Matrix-assisted laser desorption ionisation time of flight mass spectrometry. Only narrow distributions.
b c
207
a
Determination of Molecular Weights and Their Distributions
Method
208
Simone Wiegand and Werner Ko¨hler
expense are also listed. These numbers are only rough estimates and certainly depend on specific properties of the polymer like solubility or refractive index and optical absorption, which are directly related to the detection sensitivity. The focus of this chapter is on the characterization of synthetic polymers. We will discuss methods based on colligative properties, which depend on the number of molecules present and yield number average molecular weight, such as vapour and membrane osmometry, viscosity and scattering methods. In the liquid chromatographic section, we will only discuss conventional size exclusion chromatography. Then we will discuss the basic principles and recent developments of the ultracentrifugation methods. In the last section we will briefly discuss some spectroscopic methods, which are often combined with liquid chromatography methods to obtain more detailed chemical information for different fractions. Electrophoresis, which is of high importance in biochemistry, will only be discussed briefly. The few results for synthetic polyelectrolytes are summarized in some review articles [3–5]. The interested reader can find a recent book in the same series [6] that summarizes the most recent developments and techniques in this field.
2. DISTRIBUTION FUNCTIONS AND AVERAGES Some fundamental definitions and properties of distribution functions are summarized briefly in this section. The most important statistical weights, averages, and moments frequently encountered in polymer analysis are introduced [7]. Most quantities defined here will feature later again in the discussion of the individual analytical techniques. Basic definitions: Let X be some property of a polymer chain such as the degree of polymerization, molar mass, radius of gyration, or comonomer content of a copolymer, etc. In general, the polymer is heterogeneous with respect to X, which can assume discrete values Xi. We now define for molecules with X ¼ Xi . ni Mi mi ¼ niM Pi/NL xi ¼ ni = Pi ni P wi ¼ mi = i mi ¼ ni Mi = i ni Mi
Number Molar mass Total mass Relative frequency (mole fraction) Mass fraction (weight fraction)
NL is Avogadro’s number.
In many experiments average values of the property X are determined that depend on the statistical weights gi imposed by the respective experimental technique: P gi X i hXig ¼ iP (1) gi i
Determination of Molecular Weights and Their Distributions
More generally, the qth moment of X is P q gi X i q i X g¼ P ¼ mðgÞ q ðXÞ gi
209
(2)
i
ðgÞ
The average is identical to the first moment, hXig ¼ m1 ðXÞ, and the variance is 0P 12 gi X2i gi X i B i C i ¼ X2 g hXi2g ¼ P @ P A gi gi P
s2g;X
i
(3)
i
Examples: Examples of important averages frequently encountered in macromolecular science are the number (Mn), weight (Mw), z- (Mz), and viscosity average (MZ) molar masses P ni Mi i (4) M n h M in ¼ P ni P P w i Mi ni M2i i i Mw hMiw ¼ P ¼P (5) wi n i Mi i
P i
M z h M iz ¼ P i
ni M3i ni M2i
0P
MZ hMa i1=a w
11=a wi Mai B C ¼ @ iP A wi
(6)
(7)
i
a is the exponent from the Mark–Houwink–Sakurada equation for the intrinsic viscosity ½Z ¼ KMa, the weight average of which is P wi ½Zi i ½Z w ¼ P (8) wi i
and is obtained from viscometry measurements. Mn can be determined from colligative properties such as osmotic pressure, freezing point depression, or boiling point elevation (Section 3). Static light scattering gives Mw together with the z-averaged mean square radius of gyration P ni M2i R2g;i D E i (9) R2g ¼ P z ni M2i i
210
Simone Wiegand and Werner Ko¨hler
Dynamic light scattering (DLS), however, allows for the measurement of the z-average of the inverse hydrodynamic radius [8] P ni M2i R1 h;i 1 i (10) Rh z ¼ P 2 ni Mi i
Frequently it is of advantage to express various averages in terms of moments, m, for example P ni M1i hM1 in mðnÞ ðMÞ i h M in ¼ P ¼ ¼ 1ðnÞ (11) 0 0 n i Mi hM in m0 ðMÞ i
P i
h M iw ¼ P
ni M2i
i
hMiz ¼ P i
ni M3i ni M2i
(12)
ðnÞ hM3 in m3 ðMÞ mðwÞ m1ðzÞ ðMÞ 2 ðMÞ ¼ ¼ ¼ hM2 in mðnÞ m0ðzÞ ðMÞ mðwÞ 1 ðMÞ 2 ðMÞ
(13)
ni Mi
i
P
ðnÞ hM2 in m2 ðMÞ mðwÞ ðMÞ ¼ ¼ 1ðwÞ hM1 in mðnÞ m0 ðMÞ 1 ðMÞ
¼
¼
The polydispersity s2 hMiw hM2 in ¼ ¼ n;M2 þ 1 2 hMin hMin hMin
(14)
serves as a crude measure for the width of the molar mass distribution. Continuous distribution functions: Some experiments, such as liquid chromatography or mass spectrometry, allow for the determination of continuous or quasicontinuous distribution functions, which are readily obtained by a transition from the discrete property variable Xi to the continuous variable X and the replacement of the discrete statistical weights gi by the continuousR probability density g(X). 1 For simplicity, we assume g(X) as being normalized: 1 gðXÞdX ¼ 1. Averages and moments of a quantity YðXÞ are defined by analogy to the discrete case as Z 1 hYig ¼ YðXÞgðXÞdX (15) 1 q mðgÞ q ¼ hY ig ¼
Z
1
½YðXÞq gðXÞdX
(16)
1
Finally, the cumulative distribution function GðXÞ is defined as the integral function of the differential distribution function gðXÞ: Z X GðXÞ ¼ gðX0 ÞdX0 ð17Þ 1
gðXÞ ¼
d GðXÞ dX
(18)
Determination of Molecular Weights and Their Distributions
211
GðX0 Þ is the fraction of polymers with property value X less than or equal to X0. Since gðXÞ is normalized, limX!1 GðXÞ ¼ 1. Reaction mechanisms and molar mass distributions: The molar mass distribution of a synthetic polymer strongly depends on the polymerization mechanism, and sole knowledge of some average molar mass may be of little help if the distribution function, or at least its second moment, is not known. To illustrate this, we will discuss two prominent distribution functions, as examples: the Poisson distribution and the Schulz–Flory distribution, and refer the reader to the literature [7] for a more detailed discussion. The statistical growth of a constant number of chains in a living polymerization leads to the narrow Poisson distribution of the mole fraction as a function of the degree of polymerization N: xðNÞ ¼
nN1 en GðNÞ
(19)
n ¼ hN in 1 and G(N) is the gamma function. The corresponding distribution in terms of mass fractions is wðNÞ ¼
NnN1 en GðNÞðn þ 1Þ
(20)
The polydispersity decreases with increasing degree of polymerization and depends only on hN in : hN iw 2 1 ¼ 1 þ hN i1 n hN in 1 þ hN i n hN i n
(21)
The much broader Schulz–Flory distribution 1 N1 wðNÞ ¼ hN i2 n Nð1 hN in Þ
(22)
with a constant polydispersity of hN iw =hN in ¼ 2 is known from radical polymerization [9]. Figure 1 shows both a Poisson and a Schulz–Flory distribution with the same number average degree of polymerization hN in ¼ 50. The respective weight averages hN iw differ almost by a factor of two and are marked by arrows. Despite their vastly different shapes, both distribution functions would yield identical molar masses hMin in experiments based on colligative properties, such as membrane osmometry. Note that the x-axis in Figure 1 is logN, despite the labeling as N, as is common practice in plots with logarithmic axes. As a consequence, wðlogNÞ ¼ wðNÞj
dlogN 1 j ¼ wðNÞN dN
has to be plotted on the y-axis as the correct distribution function.
(23)
212
Simone Wiegand and Werner Ko¨hler
1.5
w
Poisson
w(log N)
1
0.5 w
Schulz-Flory
0
10
100
1000
N
Figure 1 Poisson and Schulz-Flory distribution with identical hNin ¼ 50. The arrows indicate hNiw ¼ 51 (Poisson) and hNiw ¼ 100 (Schulz–Flory).
3. METHODS BASED ON COLLIGATIVE PROPERTIES Colligative1 properties of dilute polymer solutions depend only on the number of dissolved molecules and not on properties of the molecules themselves, such as mass or size. Osmotic pressure, freezing point depression, boiling point elevation, and vapour pressure lowering are the most prominent examples. These methods essentially allow one to count the number n of solute molecules. From n and the known total mass m of the solute the molar mass M is readily obtained as m M ¼ NL (24) n In the case of a polydisperse polymer it is still the total number n of solute molecules that is measured and the total mass m of solute molecules that is known from sample preparation, resulting in the number average molar mass M n ¼ h M in : P P P mi ni Mi =N L ni Mi m i i i P ¼ P ¼ hMin (25) NL ¼ NL P ¼ NL n ni ni ni i
1
i
Derived from the Latin word colligere ¼ to collect, assemble.
i
Determination of Molecular Weights and Their Distributions
213
Table 2 Approximate change of colligative properties for solutions of polymers with M ¼ 20 kg/mol at 1 wt% concentration according to Ref. [10] Colligative property
Change
Boiling point elevation Freezing point depression Vapour pressure lowering Osmotic pressure
DT ¼ 0.0013 K DT ¼ 0.0025 K Dp ¼ 0.4 Pa p ¼ 1500 Pa
Since the signal is proportional to the number of solute molecules, the sensitivity of colligative methods generally decreases at a rate inversely proportional to M. In Table 2 the signal strengths of various colligative methods are compared for a polymer solution (M ¼ 20 kg/mol) at a concentration of 1 wt% [10]. Boiling point elevation and freezing point depression are of very low sensitivity, and for practical purposes membrane and vapour pressure osmometry are employed almost exclusively.
3.1 Membrane osmometry Osmosis is the passage of a pure solvent into a solution separated from it by a semipermeable membrane, which is permeable to the solvent but not to the polymeric solute. The osmotic pressure p is the pressure that must be applied to the solution in order to stop the flow. Equilibrium is reached when the chemical potential of the solvent is identical on either side of the membrane. The principle of a membrane osmometer is sketched in Figure 2. The osmotic pressure is given by m 1 @DGm p ¼ ðV s Þ (26) @n~ s p;T;n~ p ~ s and n~ p the molar concentrations of the Vm s is the molar volume of the solvent, n solvent and the polymer, respectively, and DGm the Gibbs free energy of mixing. Equation (26) reduces in the limit of infinite dilution to the well-known Van’t Hoff equation p RT ¼ (27) c h M in hMin is the number average molar mass of the solute (polymer), R ¼ 8.315 J/K mol the gas constant, and c the polymer concentration in polymer mass per volume solution. Finite concentrations are treated in terms of a virial expansion p 1 ¼ RT þ A2 c þ A3 c2 þ (28) h Mi n c which, in case of dilute solutions, usually can be terminated after the second virial coefficient A2. A2 accounts for both excluded volume effects and repulsive
214
Simone Wiegand and Werner Ko¨hler
π = ρgh
solvent
solution
Figure 2 Principle of membrane osmometry. r is the solvent density, g the acceleration of gravity, and h the difference between the fluid levels in both chambers.
or attractive forces between the solute molecules. Within the framework of the Flory–Huggins lattice model with interaction parameter w it takes the form [11] h i1 1 2 w Vm A2 ¼ (29) s rp 2 Vm s is the molar volume of the solvent and rp the density of the polymer. For polydisperse polymers A2 is a more complex average, which shall not be discussed here in detail [7]. For good solvents and high concentrations, the influence of the 3rd virial coefficient A3 cannot be ignored, and p=c versus c sometimes does not lead to a linear plot. In these cases, a linearization can frequently be obtained with the approximation A3 ¼ A22 hMin =4 by plotting [12,13] p 1=2 RT 1=2 1 ¼ 1 þ A2 hMin c (30) h M in c 2 Experimental considerations: Today, solid-state pressure transducers with a high mechanical stiffness are employed to ensure a reasonable response time. Membrane materials are cellulose, cellulose acetate, porous glass, or Teflons. The choice of the optimum membrane strongly depends on the system under investigation and is a major experimental problem in membrane osmometry [14]. The membrane must be inert and compatible with the solvent. The low molecular weight cut-off should be as low as possible. To avoid long equilibration times due to ballooning, the membrane material should have a high solvent permeability and sufficient mechanical stiffness and tensile strength. Osmometers with automatic pressure compensation and flow cells [15–17] have been developed for rapid measurements.
Determination of Molecular Weights and Their Distributions
215
Practically, polymers with molar masses between 2 104 and 2 106 g=mol can be characterized by membrane osmometry, but measurements of Mn o104 g=mol have also been reported with fast instruments and suitable membranes [16]. The lower limit is set by insufficient retention of short polymer chains. Above M 2 106 g=mol, the osmotic pressure, which is proportional to M1 , is too low for a reasonable signal-to-noise ratio. An advantage of the low molar mass cut-off is that impurities with a very low molar mass can permeate through the membrane and, hence, do not contribute to the measured osmotic pressure. Their equilibration time may, however, be different from that of the solute, leading to complex time-dependent signals. For a typical experiment, a series of solutions with concentrations between 1 and 10 g/L is prepared. Solutions and pure solvent, which defines the baseline, are injected alternately into the solution chamber of the osmometer and enough time is given for the pressure to equilibrate. Equilibrium is reached after seconds to days, depending on the instrument, the membrane, and the sample. p=c is plotted as a function of c according to Equation (28). The value extrapolated back to c ¼ 0 gives hMin , and A2 is obtained from the slope. Figure 3 shows measurements with an osmometer with a very short equilibration time of only a few seconds. The instrument contains a flow cell based on a poly(acrylonitrile) membrane [17]. The small pore size together with the rapid response results in a very low effective cut-off around 5 kg/mol [16]. Note, however, that even an infinitely fast osmometer is not able to yield the correct molar mass of permeating solutes due to the Staverman effect [18], which accounts for the reduced osmotic pressure due to solute molecules that are able to permeate through the membrane, even though they have not yet done so.
3.2 Vapour pressure osmometry Vapour pressure osmometry is the second experimental technique based on colligative properties with importance for molar mass determination. The vapour pressure of the solvent above a (polymer) solution is determined by the requirement that the chemical potential of the solvent in the vapour and in the liquid phase must be identical. For ideal solutions the change of the vapour pressure p of the solvent due to the presence of the solute with molar volume Vm s is given by p0 p c ¼ Vm (31) s h M in p0 p0 is the vapour pressure of the pure solvent. Practically, the small change in vapour pressure is difficult to measure, and the Clausius–Clapeyron equation is employed to translate the vapour pressure difference at constant temperature to a temperature difference at constant vapour pressure [19]: dp DH vap p ¼ dT RT 2
(32)
216
Simone Wiegand and Werner Ko¨hler
(a) 480
500
460
(π/c) / (J/kg)
440
Δp / Pa
400
300
420
60 40 20
0
1
2
200
3 c / (g/L)
4
5
6
100
0
0
5
10 t / m in
15
20
(b) flush
pressure transducer
flush
out
in
holder gasket membrane
solvent solution
seal glass tube
Figure 3 Membrane osmometry. Top: concentration series with multiple injection of polystyrene (PS, 5,250 g/mol) in toluene. Concentrations: 1.07, 1.91, 2.94, 4.11, and 5.03 g/L. Multiple solvent injections establish the baseline (subtracted). Inset: data evaluation for concentration series of PS (5,250 g/mol) and PS (47,400 g/mol) in toluene. Bottom: design of osmometer equipped with flow cell. Reproduced with permission from Lehmann et al. [16]. Copyright 1996 American Chemical Society.
Determination of Molecular Weights and Their Distributions
217
DH vap is the molar heat of vaporization. Hence, Dp DT DH vap p c ¼ xp ¼ V m ¼ s p T RT hMin
(33)
In principle, DHvap can be obtained from other sources and hMin can be calculated from Equation (33) without any a priori assumptions. In reality there are always thermal leaks and the instruments are calibrated with a known standard. If DV / DT is the measured voltage difference and K the instrument calibration constant, hMin is obtained as [20] 1 DV hMin ¼ K lim (34) c!0 c As for the case of membrane osmometry, non-ideality is accounted for by a virial expansion (Equation (28)). Experimental considerations: Sample preparation and data evaluation are similar to membrane osmometry. Since there is no lower cut-off as in membrane osmometry, the method is very sensitive to low molar mass impurities like residual solvent and monomers. As a consequence, the method is more suitable for oligomers and short polymers with molar masses up to hMin 50 kg=mol. Today, vapour pressure osmometry faces strong competition from mass spectrometry techniques such as matrix-assisted laser desorption ionisation mass spectrometry (MALDI-MS) [20,21]. Nevertheless, vapour pressure osmometry still has advantages in cases where fragmentation issues or molar massdependent desorption and ionization probabilities come into play. Technically, two matched thermistors are placed within a thermally insulated compartment with a saturated solvent atmosphere. A droplet of solvent is placed onto one, a droplet of solute onto the other thermistor (Figure 4). Solvent will condense into the solution droplet and raise its temperature until the solution has the same vapour pressure as the solvent. At this point, the temperature difference between the two droplets is read. Solvents with sufficient vapour pressure, such as toluene, tetrahydrofuran, or chloroform, are best suited for strong signals, but water has also been used successfully. ΔT thermistors
solution
solvent
solvent vapor
Figure 4 Principle of operation of a vapour pressure osmometer.
218
Simone Wiegand and Werner Ko¨hler
4. VISCOMETRY The most obvious characteristic of a solution of a high polymer is that its viscosity is considerably higher than that of the pure solvent, even when the concentration of polymer is quite small [22]. The suggestion was first made by Staudinger in 1930 [1,2] that the relative magnitude of this increase in viscosity could be quantitatively correlated with the molecular weight of the polymeric solute. In a polymer solution the specific viscosity is defined as Zsp ¼ ðZ Z0 Þ=Z0 with the solution and solvent viscosity Z and Z0 , respectively. The intrinsic viscosity (Staudinger index) of a polymer is defined as Zsp 5 Vh ½Z ¼ lim ¼ NL (35) c!0 c 2 M The specific viscosity Zsp of a dilute solution of spheres is directly related to their hydrodynamic volume V h . N L denotes Avogadro’s number. Typically the intrinsic viscosity ½Z follows a scaling law, the so-called Mark–Houwink– Sakurada equation: ½Z ¼ KMa
(36)
The scaling exponent a can be related to the particle shape. One finds a ¼ 2, 0, 0.5, and 0.8 for a thin rod, solid sphere, ideal chain, and swollen chain, respectively. For most polymers K and a have been tabulated [23]. For a monodisperse sample Equation (36) can be used for a crude determination of the molar mass: 1=a ½ Z M¼ (37) K For polydisperse samples, the weight average intrinsic viscosity ½Z w is measured (Equation (8)) and the so-called viscosity averaged molar mass is obtained: !1=a ½Z w hKMa iw 1=a MZ ¼ ¼ ¼ hMa i1=a (38) w K K MZ is usually between Mn and Mw and closer to Mw (compare with Section 2). Figure 5 shows three different types of capillary viscometers often used for viscosity measurements of polymer solutions. The disadvantage of the Oswald viscometer is that the viscometer has to be charged with the solution to a precise level and fine adjustments need to be made at the temperature of measurement. The Ubbelohde viscometer, also frequently referred to as the suspended level viscometer, is particularly useful when a series of different polymer concentrations is to be measured. The filling volume needs not to be adjusted precisely. The largest dilution ratio obtainable is limited only by the ratio of the volume of bulb B to that of the volume between the bottom of bulb B and the top of bulb C. For the compact version (Figure 5(c)) smaller sample volume is needed. There are also capillary viscometers available that can be coupled with liquid
Determination of Molecular Weights and Their Distributions
(a)
(b)
219
(c)
D C
A B
Ostwald
Ubbelohde dilution (normal)
Ubbelohde dilution (compact)
Figure 5 Sketch of the (a) Oswald viscometer, (b) Ubbelohde dilution viscometer in the normal form, and (c) compact form.
chromatography for on-line viscosity measurements. These instruments derive the viscosity from the pressure drop across a thin capillary through which a constant solvent flow is sustained. For all capillary instruments the time t needed for a certain volume V of the solution to flow through a thin capillary of length l and radius R is measured. Assuming a laminar flow, the Hagen–Poisseuille equation can be applied, leading to V pDp 4 ¼ R (39) t 8Zl If the density does not change significantly with concentration, the specific viscosity Zsp ¼ t=t0 1 can be approximated from the times measured for the solution (t) and solvent (t0). The dimension of the bore diameter of the capillary needs to be chosen carefully to minimize kinetic corrections. A detailed discussion of correction effects and other pitfalls can be found in the book by Van Wazer et al. [24]. Experimental considerations: For the measurement typically several concentrations are prepared and the specific viscosity Zsp or reduced viscosity Zred ¼ Z=Z0 are extrapolated to zero concentration. In the literature three different approaches are used to obtain the intrinsic viscosity and, with known ½Z–M relation, the molar mass. Schulz–Blaschke [25] Huggins [26] Kraemer [27]
Zred ¼ [Z]+[Z]KSB Zsp Zred ¼ [Z]+[Z]2KHc (ln Zred)/c ¼ [Z]+[Z]2KKc
(40)
The coefficients depend on the interactions between the solute molecule and the solvent. For good solvents typical values are KSB 0:3 and
220
Simone Wiegand and Werner Ko¨hler
KH 0:3; . . . ; 0:4. Furthermore the difference KH –KK is approximately equal to 0:5 [7]. A viscosity online detector in a size exclusion chromatography (SEC) instrument allows for a universal calibration for polymers with known K- and a-values. For polymers that are only soluble at high temperature, e.g., polyolefines, high-temperature detectors are available, which can be operated up to 2001C. In addition to molar mass measurements, viscosity detectors have also been employed successfully to obtain structural information of branched polymers [28]. The molar mass dependence of the intrinsic viscosity of rigid chain polymers cannot be described by a simple scaling relation in the form of Equation (36) with molar mass independent of K and a over a broad molar mass range. Starting from the worm-like chain model, Bohdanecky´ proposed [29] the linearizing equation 2 1=3 M ¼ AZ þ BZ M1=2 (41) ½Z where AZ and BZ are related to the persistence length and the hydrodynamic diameter of the polymer chain. Equation (41) has been employed to determine a persistence length (see Chapter 4) of 13 nm for polydisperse poly(p-phenylenes) with sulfonate ester- and dodecyl side groups [30] (Section 9.1).
5. SCATTERING TECHNIQUES Light scattering is a quite powerful tool that provides information not only about the molecular weight but also the radius of gyration and the second virial coefficient. It is not a suitable method for very low molecular weights below Mo104 g=mol, because of the low scattering strength. It is an absolute method and is, in general, also suitable for polyelectrolytes if long-ranged electrostatic interactions are sufficiently screened. Complications occur in the case of mixed solvents and copolymers. For polydisperse samples light scattering yields mass weighted molecular weights hMiw . This has to be taken into account, if one compares the results with other methods such as SEC.
5.1 Static light scattering In a static light scattering experiment the mass average molecular weight Mw of a dissolved polymer can be determined [31–33]. The components of a light scattering set-up are illustrated in Figure 6. In the elastic light scattering experiment the incident light with the vacuum wavelength l induces oscillating dipoles, which radiate a scattered wave of the same wavelength as the incident light. The unpolarized or vertically polarized scattered light is typically detected by a photomultiplier or an avalanche diode detector. The observed scattering intensity depends on the polymer concentration, the size and mass of the polymer, interactions and the optical contrast of the polymer in the solvent. The latter is
Determination of Molecular Weights and Their Distributions
221
Figure 6 Sketch of a typical light scattering set-up. Typically in the static light scattering experiment the incident beam is polarized vertically (v), while the scattered light is detected unpolarized (vv and vh). ~ ki and ~ ks are the wave vectors of the incident and scattered light, respectively.
reflected in the refractive index increment ð@n=@cÞp;T , which describes the change of the refractive index increment n with increasing polymer concentration c at constant temperature T and pressure p. In static light scattering experiments the time-averaged scattering intensity Is is recorded at different scattering angles y, which is the angle between the direction of the incident and the scattered light. Often the scattering vector q ¼ ð4pn=lÞsinðy=2Þ is used instead of the scattering angle, which makes it directly possible to compare results obtained for different wavelengths. In general the scattering intensity IðqÞ / PðqÞSðqÞ is proportional to the product of the form factor PðqÞ and the structure factor SðqÞ. The form factor PðqÞ accounts for the single particle properties, such as size and molar mass, while the structure factor SðqÞ accounts for interactions between the solute particles. Using the theoretical considerations of Debye and Rayleigh for coherent scattering of light, Zimm [34] derived the fundamental equation for static light scattering ! q2 R2g Kc 1 ¼ 1þ (42) þ 2A2 c Rðq; cÞ M 3 with the optical constant K ¼ ð@n=@cÞ2p;T 4pn2solvent =ðN L l40 Þ, the molar mass M, the radius of gyration Rg and the second virial coefficient A2. For polydisperse polymers the weight average molar mass hMiw and the z-average mean square radius of gyration hR2g i are measured. The refractive index increment ð@n=@cÞp;T z
has to be looked up in reference tables or needs to be determined independently. Very accurate values can be obtained with an interferometer [35]. Practically the reduced scattering intensity Rðq; cÞ is determined as the difference between the scattering intensity of the solution RðsolutionÞ and the solvent RðsolventÞ according to Rðq; cÞ ¼ RðsolutionÞ RðsolventÞ ¼ RðstandardÞ
rðsolutionÞ rðsolventÞ n2solvent rðstandardÞ n2standard
ð43Þ
222
Simone Wiegand and Werner Ko¨hler
where rðsolutionÞ, rðsolventÞ, rðstandardÞ, nsolvent , and nstandard are the volume corrected scattering intensities and refractive indices for the solution, solvent, and standard, respectively. The measured scattering intensities are related to the scattering intensity of a known standard, for which the absolute Rayleigh ratio RðstandardÞ is that of the standard solvent. The absolute Rayleigh ratio RðstandardÞ has been measured for various solvents and wavelengths [36,37]. The knowledge of this absolute scattering ratio makes static light scattering an absolute, calibration-free method. It should be pointed out, that the absolute molecular weight can only be as precise as the determined Rayleigh ratio for the standard solvent at a certain wavelength. Special care has to be taken if the polymer is only soluble in a solvent mixture or if a certain property, e.g., a definite value of the second virial coefficient, needs to be adjusted by adding another solvent. In this case the analysis is complicated due to the different refractive indices of the solvent components [32]. In case of a binary solvent mixture we find, that formally Equation (42) is still valid. The refractive index increment needs to be replaced by an increment accounting for a complex formation of the polymer and the solvent mixture, when one of the solvents adsorbs preferentially on the polymer. Instead of measuring the true molar mass Mw the apparent molar mass Mapp is measured. How large the difference is depends on the difference between the refractive index increments ð@n=@cÞm ð@n=@cÞA;0 . ð@n=@cÞm is the increment determined in the mixed solvents in osmotic equilibrium, while ð@n=@cÞA;0 is determined for infinite dilution of the polymer in solvent A. For clarity we omitted the fixed parameters such as temperature, T, and pressure, p. sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi! Mapp @n @n @n ¼ 1 (44) @c m @c A;0 @c A;0 Mw The true second virial coefficient can be calculated via A2 ¼ A2;app ðMapp =Mw Þ. In the case of copolymers the heterogeneity parameters need to be considered in the analysis. If we assume an AB-copolymer the heterogeneity parameters are given by X P¼ xA;i x¯ A Mi wi (45) i
and Q¼
X i
2 xA;i x¯ A Mi wi
(46)
The deviations in composition xA;i x¯ A are weighted by the z-statistical weights wi Mi . The apparent molecular weight Mapp is given by n n 2 nA nB A B Mapp ¼ Mw þ 2P þQ (47) n n nA @n=@cA and nB @n=@cB are with respect to the components A and B and n the overall refractive index increment of the heterogeneous copolymer [32].
Determination of Molecular Weights and Their Distributions
223
Experimental considerations: Static light scattering allows the simultaneous determination of the molar mass, the radius of gyration, and the second virial coefficient, which are important parameters in the characterization of polymer solutions. This holds also for the less common X-ray and neutron scattering experiments (cf. Section 5.3). A graphical analysis of the scattering intensities according to Equation (42) is called a Zimm-plot. Typically, one prepares a dilution series of at least four concentrations and determines the scattering intensities for all concentrations, the solvent and the standard in the entire available scattering angle range, typically from 201 to 1601. Using Equation (43) and the optical constant leads to a Kc=R-values for each concentration and scattering vector q. According to Equation (42) the Kc=R-values for a fixed concentration are extrapolated to q ¼ 0. The slope of the extrapolated values (open squares in Figure 7) is equal to 2A2 kc, with k an arbitrary chosen constant to shift the data for clarity. Additionally the Kc=R-values are extrapolated at fixed scattering vector to infinite dilution (open circles in Figure 7). The slope gives R2g =ð3MÞ and the intersect of both extrapolated lines is inverse to the molecular weight M. Unfortunately, the extrapolations to obtain the molecular weight, the radius of gyration and the second virial coefficient are not always as simple as suggested by Equation (42). Figure 8 shows a Zimm plot for xanthan in 10 mM sodium chloride (NaCl) solution [38]. The plot clearly shows deviations from the linear behavior in dependence on q indicating that the linear approximations (q2 R2g =3 1) are no longer valid. The deviations from the linear behavior reflect the form factor dependence. Non-linearities in the concentration dependence may indicate higher order virial coefficients become important. Although not so
Figure 7 Schematic Zimm plot: The determined Kc=R values (), the extrapolated values for fixed concentrations to q ¼ 0 (&), and the extrapolated values for fixed scattering vector to infinite dilution (3) c ¼ 0.
224
Simone Wiegand and Werner Ko¨hler
Figure 8 Zimm plot for xanthan in an aqueous solution of 10 mM NaCl. Reproduced with permission from Berth et al. [38]. Copyright 1996 American Chemical Society.
often displayed in the literature these sort of deviations from the linear behaviour are very often observed. And not always is the origin of the curvature clear [39]. In order to describe the data a quadratic extrapolation needs to be used. The inverse of the intercept leads to a molecular weight of Mw ¼ 3:12 106 g=mol and the limit of the two slopes with y ! 0 and c ! 0 lead to a radius of gyration with Rg ¼ 264 nm and a second virial coefficient of A2 ¼ 5:5 104 mol mL=g. If the curves are moderately bent often a Berry plot [40] instead of a Zimm plot is used. Berry proposed plotting the square root of c=R against c and sin2 ðy=2Þ, because these plots show less curvature. As a reason for this it was presumed that the contribution of the third virial coefficient A3 becomes significant, and that A3 / A22 . This procedure is similar to the one described for membrane osmometry (Equation (30)). For very high molecular weights, the ordinate intercept is close to zero, and the values obtained for Mw and Rg become very uncertain. In this case often the Guinier method [41] is used plotting lnðR=KcÞ as a function of sin2 ðy=2Þ for each concentration and then plotting the slopes and intercepts at y ¼ 0 against concentration. A careful characterization of copolymers is quite time consuming and a combination of methods as discussed in Section 6.1 might be considered. In practice the situation is often complicated by an amphiphilic character of the copolymers, which leads additionally to micelle formation.
Determination of Molecular Weights and Their Distributions
225
5.2 Dynamic light scattering In static light scattering only the time average of the scattered intensity is recorded, while DLS measures the scattered intensity with a time resolution of milliseconds or even tenths of nanoseconds. These fluctuations in the scattered intensity can be related to dynamical processes within the sample. As long as the solution is highly diluted and the solute particles move independently, the particles follow Brownian dynamics. This implies that the probability Pðr; tj0; 0Þ to find a particle at time t at the position r, which was originally located at t ¼ 0 at r ¼ 0, is given by [42] Pðr; tj0; 0Þ ¼ ð4pDtÞ3=2 exp r2 =4Dt (48) The temporal evolution of Pðr; tj0; 0Þ is determined by the diffusion coefficient D. Owing to the movement of the particles the phase of the scattered light shifts and this leads to intensity fluctuations by interference of the scattered light on the detector, as illustrated in Figure 9. Depending on the size of the polymers and the viscosity of the solvent the polymer molecules diffuse more or less rapidly. From the intensity fluctuations the intensity autocorrelation function gð2Þ ðtÞ ¼ IðtÞIðt þ tÞ (49) is calculated. t is any arbitrary delay time. The intensity autocorrelation function g2 ðtÞ decays for ergodic systems from the mean square intensity limt!0 gð2Þ ðtÞ ¼ IðtÞ2 to the asymptotic square of the mean intensity 2 limt!1 g ð2Þ ðtÞ ¼ IðtÞ . This is a consequence of the so-called Siegert relation, which relates the time autocorrelation function of the scattered field to that of the scattered intensity. For a detailed discussion of this point see Refs. [42,43]. After normalization to the asymptotic baseline, g2 ðtÞ decays from two to unity if measured with a perfect instrument. A real instrument always suffers from some loss of coherence, and for a monodisperse solution of ideal, non-interacting solute molecules the intensity autocorrelation function g2 ðtÞ takes the form gð2Þ ðtÞ ¼ A þ Bjgð1Þ ðtÞj2
Figure 9 (A) Intensity fluctuations caused by random particle motion. (B) Intensity autocorrelation function versus time.
(50)
226
Simone Wiegand and Werner Ko¨hler
A and B are instrumental factors and gð1Þ ðtÞ the electric field correlation function which is related to the translational diffusion coefficient D by gð1Þ ðtÞ ¼ expðGtÞ ¼ expðq2 DtÞ
(51)
with G as decay rate. For infinite dilution (neglecting interactions) the diffusion constant can be related to the hydrodynamic radius Rh of the polymer by the Stokes–Einstein equation D ¼ kB T=6pZRh , with the dynamic viscosity Z, temperature T, and the Boltzmann constant kB. In a more realistic case of a polydisperse solution, gð1Þ ðtÞ will be a sum of exponentials (one for every molecular weight species present) and Equation (51) becomes Z 1 ð1 Þ g ðtÞ ¼ GðGÞ expðGtÞdG (52) 0
Here GðGÞ is the distribution function of decay rates G. In order to approximate G(G) the lower moments can be determined [45,46] according to ln gð1Þ ðtÞ ¼ Gt þ 1 m2 Gt 2 1 m3 Gt 3 þ (53) 2 3 2! G 3! G P with m2 and m3 being the second and third moments mi ¼ i ðG GÞi . For unimodal distributions of slightly polydisperse polymers in solution, the following relation has been derived [46] m2 ðMz =Mw 1Þ=4 (54) 2 G which is valid in the approximation Mz =Mw 1:25. The average G is given as a zaverage of the decay rates P ni M2 Gi G ¼ P i 2 ¼ hG iz (55) n i Mi and consequently the hydrodynamic radius is an inverse z-average (cf. Section 2, Equation (10)). Recently, Frisken [47] derived a different expression for gð2Þ by expanding the correlation function in terms of the moments about the mean: m m 2 gð2Þ ¼ B þ bexp 2Gt 1 þ 2 t2 3 t3 (56) 2! 2! Frisken was able to show that this function is more robust to poor guesses and leads to consistent results compared to Equation (53) when different numbers of points are fitted. Experimental considerations: Frequently a numerical inverse Laplace transformation according to a regularization algorithm (CONTIN) suggested by Provencher [48,49] is employed to obtain GðGÞ. In practice the determination of the distribution function GðGÞ is non-trivial, especially in the case of bimodal and n-modal distributions, and needs careful consideration [50]. Figure 10 shows an autocorrelation function for an aqueous polyelectrolyte solution of a low concentration (c ¼ 0.005 g/L) at a scattering vector of q ¼ 8:31 106 m1 [44].
Determination of Molecular Weights and Their Distributions
227
Figure 10 Polarized field autocorrelation function g(1) for poly(p-phenylene) Mw ¼ 2.1 106 g/mol) in water, which is denoted CVV ðtÞ in the original work [44]. The subscript indicates that both the incoming beam and the scattered light are vertically polarized. The correlation function was recorded for a solution with a concentration of c ¼ 0.005 g/L at a scattering vector of q ¼ 8.31 106m1. The inset shows the distribution function of the relaxation times determined by an inverse Laplace transformation.
The inset shows a unimodal distribution of relaxation times t ¼ G1 obtained by a CONTIN analysis. Besides CONTIN there is a number of alternative techniques [51] for the determination of the distribution from the correlation function. Detailed discussions of this topic have been given by Stock and Ray [52] and by Sˇteˇpa´nek [50]. A way to increase the precision of the value Mw =Mn extracted from DLS is to consider several correlation functions and to look for a single answer. Sˇteˇpa´nek [50] developed a method to determine the polydispersity of polymer samples with narrow distribution by measuring several correlation functions with different sample times on a linear correlator. With this procedure polydispersities in the range Mw =Mn ¼ 1:05 2 can be determined. DLS is a rapid method, typically measurements can be made within a few minutes, and only small quantities of sample ( 50 mg) are needed. The polymers might be suspended in any clear liquid. The samples need to be prepared carefully. Dust needs to be avoided by filtering the samples. Also air bubbles will falsify the results. In the case of more complex systems, such as micellar solutions or copolymer solutions, charged impurities with long range interactions need to be avoided, because they might influence the phase behavior of the systems. The main disadvantage of the method is, that in DLS it is not the molar mass distribution that is obtained, but the intensity-weighted composite of the decay rates Gi of all species present in the solution. In order to obtain for instance the distribution of weight fraction cðMÞ of the polymer as a function of molar mass as obtained by SEC the following scaling law G ¼ aMb and the weighting factor GðGÞ / cðMÞM needs to be used (Section 9.2).
(57)
228
Simone Wiegand and Werner Ko¨hler
5.3 Other scattering methods In principle it is also possible to perform a static scattering experiment using other radiation sources such as neutrons or X-ray radiation. In a typical polymer analysis those sources are often not readily available, therefore we only briefly discuss these possibilities. For instance Kirste et al. [53] determined the molecular weight of various poly(methyl methacrylates) in the molecular range between 6,000 and 106 g/mol by neutron scattering. A big advantage of neutron scattering compared to light scattering is the possibility to characterize very low molecular weight polymers (Mw ¼ 1; 000 g=mol). This can be achieved by contrast variation [54]. For polydisperse samples the disadvantage of the low sensitivity of DLS for low molecular weights can be overcome by a more sophisticated technique the so-called Thermal Diffusion Forced Rayleigh Scattering (TDFRS) method, availability of which is currently limited to a few scientific laboratories. For instance it has been shown that the molecular weight distribution of a mixture of two narrow polystyrenes (Mw /Mn I1.03) with molar masses of Mw;1 ¼ 48 kg=mol and Mw;2 ¼ 556 kg=mol at equal concentrations (c1 ¼ c2 ¼ 0.0029), dissolved in ethyl acetate leads to a distribution function which is in good agreement with the SEC results, while the DLS data are dominated by the high molecular weight polymer [55]. Again it needs to be pointed out, that all methods have their weaknesses and it is certainly not justified to regard the SEC distribution as the true molar mass distribution, as it may suffer from calibration problems, solute–column interactions, peak broadening, and a molar mass dependence of the contrast factor @n=@c, and hence the detector sensitivity.
6. LIQUID CHROMATOGRAPHY 6.1 Size-exclusion chromatography SEC or gel permeation chromatography (GPC) is one of the widely used chromatographic techniques [56,57]. In contrast to the already discussed colligative and scattering methods it is not an absolute method and requires proper calibration with some known polymer standards. One obtains not only the average molar masses (Mn , Mw , Mz ) but the complete molar mass distributions. Figure 11(A) shows a principle sketch of a SEC set-up. The eluent (solvent) is pumped at a constant flow rate through the system. A small amount of polymer solution (typically 200 mL) is injected manually or with an autosampler. The main part comprises a set of columns (typically 3–4 columns+pre-column) typically packed with microporous styrene-divinylbenzene, porous glass, or silica. In the routine analytical laboratory it is especially useful to have a pre-column in order to collect impurities that might be present in the samples. If many different samples are to be analyzed, it is necessary to check the reliability of the columns frequently to avoid artefacts due to residues from previous samples still held on the column. In order to avoid problems, samples should be purified before they
Determination of Molecular Weights and Their Distributions
229
high mass low mass injection separation eluted eluted
injection loop
columns detector unit
pump waste detector
eluent
(A)
chromatogram injection
(B)
time
Figure 11 (A) Sketch of the basic components in a typical SEC set-up. (B) Principle of separation by SEC.
are injected onto the column. The pre-column should be replaced frequently to protect the column set. The separation process, illustrated in Figure 11(B), is based on the molecular hydrodynamic volume of the polymer species. Higher molar mass species that are too large to penetrate into the pores of the stationary phase elute first; smaller ones that can diffuse into the pores appear at later times corresponding to higher elution volumes. The total volume V t occupied by the eluent within the column is the sum of the interstitial or void volume V 0 , which is equal to the volume of the mobile phase, and the volume V p within the pores. Different molecular weight fractions elute at a certain retention time corresponding to retention volume V R : V R ¼ V0 þ kV p
(58)
The coefficient k is a measure of how much time a polymer with a certain chromatographic radius Rc spends within the pores of radius rp . The factor k can vary between 0 (V R ¼ V 0 ; molecules are too large to penetrate the pores; exclusion limit) and 1 (V R ¼ V 0 þ V p ¼ V t ; all pores are accessible to the solute; separation threshold). For some polymers, like polystyrene or poly(methyl methacrylate), narrow standards of known molar mass and small polydispersity are commercially available, which can be used for calibration. Unfortunately, such standards are not available for all polymers and then the obtained true molar masses of a specific polymer might differ by a factor of two from the value obtained by calibration with, e.g., polystyrene [30] (see Section 9.1). This problem can be resolved by the so-called universal calibration, which is based on the finding that the retention volume of a polymer is a single-valued function of the hydrodynamic volume of the polymer, irrespective of its chemical nature and
230
Simone Wiegand and Werner Ko¨hler
structure. The hydrodynamic volume Vh of a polymer is proportional to the product of intrinsic viscosity and molar mass Vh ¼
2 4 ½ZM pR3c 5N L 3
(59)
which we set equal to its chromatographic volume. If two polymers have the same retention volume or retention time, the product ½Z1 M1 ¼ ½Z2 M2 is constant. Using the Mark–Houwink–Sakurada relation ½Z ¼ KMa [7] one finds K1 1þa1 1=ð1þa2 Þ M2 ¼ M K2 1
(60)
For many polymers K and a values can be found in the Polymer Handbook [23]. In a recent study by Vanhee et al. [30] the universal calibration has been applied using the polystyrene (PS) calibration curve to characterize rigid rod poly(p-phenylenes) (PPP). It turned out that due to its larger persistence length, PPP with a certain mass requires a much larger volume than PS for the same molecular weight. Ron et al. employed universal calibration for the characterization of erodible copolymers [58]. Experimental considerations: Detectors used to monitor concentration changes in the column effluent can be classified into three categories according to their sensitivity to different statistical weights. In the first case the signal is proportional to the mass fraction or concentration (differential refractometer, UV spectrometer). The second group contains detectors that are sensitive to cM (light scattering) and in the third group the signal is proportional to c=M (vapour pressure osmometry). Often it is useful to use several online detectors or combine the SEC instrument with other methods. For instance the combination of a light scattering detector or a flow-membrane osmometer with a concentration detector allows an absolute calibration of the elugram. This is particularly useful for novel polymers in research and development, where a universal calibration is not possible, because the K and a values are unknown. In the case of heterogeneous polymers the experimental methods need to be refined. In order to analyze those polymers it is necessary to determine a set of functions f i ðMÞ, which describe the distribution for each kind of heterogeneity i. This could be the mass distributions of the blocks in a diblock copolymer. The standard SEC methods fail here and one needs to refine the method, e.g., by performing liquid chromatography at the critical point of adsorption [59] or combine SEC with methods, which are, for instance, sensitive to the chemical structure, e.g., high-pressure liquid chromatography (HPLC), infrared (IR), or nuclear magnetic resonance spectroscopy (NMR) [57]. Most widely used is the two-dimensional combination of SEC and HPLC for copolymer characterization. The typical HPLC instrument is very similar to an SEC apparatus. While the ideal SEC separation is exclusively determined by entropy changes, in HPLC or adsorption chromatography it is assumed that no
Determination of Molecular Weights and Their Distributions
231
entropic effects take place and the distribution is exclusively determined by enthalpic effects. This means that large molecules, which interact more strongly with the column, elute after the small molecules. The mobile phase needs to dissolve the sample, but it should also minimise interactions between solute and the stationary phase and it needs to be compatible with a specific detector. Under certain circumstances it might also be required to run a solvent gradient, where the miscibility of the components is a necessary condition. Figure 12 shows a schematic representation of 2D chromatography set-up combining SEC and HPLC. The main part is an eight-port injection valve with two storage loops. In the first step loop 1 is loaded by HPLC and in the mean time loop 2 is analyzed by SEC. In the next step the loops are exchanged. Typically the HPLC separation requires more time due to lower flow rates, therefore it is advantageous first to load one loop by HPLC and later to analyze the fraction by SEC. In the case of copolymers it is also necessary first to separate the polymers according to their chemical composition, such as blocklength ratio, before analyzing the molecular weight distribution. An important feature for such an automated set-up is the proper coordination of the flow rates of both systems. Furthermore one needs to pay attention to the fact, that a further dilution of the sample takes place when a fraction is injected into the SEC system. Therefore, detectors with a high sensitivity are required. A combination of infrared spectroscopy with size exclusion chromatography has a wide application range in the characterization of copolymers, adhesives, impurity profiling in polymers and branching in polyolefines [60–65]. Commonly, the solvent used as a mobile phase absorbs strongly in the
Figure 12 Schematic representation of 2D chromatography using an eight-port injection valve and two storage loops. (A) In the first position of the valve the storage loop 1 is loaded with the HPLC eluent, while the content of the storage loop 2 is analyzed by SEC. (B) In the second valve position storage loop 2 is loaded with HPLC eluent and the content of loop 1 is analyzed according the molecular size of the solute.
232
Simone Wiegand and Werner Ko¨hler
infrared (IR), so that practical use of an IR cell is only possible for some solvents. There are commercial interfaces available, which remove the solvent either by a pneumatic nozzle or in an ultrasonic/vaccuum nebulizer. The non-volatile substrates will for instance then be deposited on a slowly rotating germanium disk, which is then automatically or manually transfered to a Fourier transform infrared (FT-IR) spectrometer. The pneumatic nozzle typically works for solvents with a boiling point around 1001C. For less volatile solvents the required temperatures at the nozzle become high and the allowed flow rates are very low, so that the ultrasonic/vaccuum nebulizer is more suitable. Special care has also to be taken to use volatile buffers instead of salts if needed in aqueous SEC. If further structural information is required, it is possible to use the deposited material in other instruments such as an NMR or mass spectrometer. NMR and IR are powerful spectroscopic techniques, which provide additional information about the compositional details of a sample. However, they are often unable to differentiate between a polymer blend A þ B and a copolymer consisting of A and B. For such complex polymer compositions a combination of liquid chromatography and spectroscopic methods is helpful. In his recent review Pasch [57] discusses a couple of examples. In conclusion one can say that SEC is a very powerful method for polymer characterization, especially in combination with other composition sensitive or absolute calibration methods. A big advantage is also that the sample amount is fairly small, typically 10 mg. For more complex polymers, such as polyelectrolytes, enthalpic effects often become dominant and also for rather high molecular weight polymers chromatographic methods such as field-flow fraction (FFF) techniques might be more suitable. For fast routine measurements linear columns are often used.
6.2 Field-flow fractionation FFF is a family of flexible elution techniques capable of simultaneous separation and measurement. The FFF mechanism combines elements of chromatography and field-driven techniques such as electrophoresis and ultracentrifugation. Different properties of the polymers or colloidal particles can be determined depending on the applied field. The fundamental principle of FFF is illustrated in Figure 13(A). The separation of the sample takes place inside a narrow ribbonlike channel. This channel is composed of a thin piece of sheet material (usually 70–300 mm thick Mylars or polyimide) in which a channel is cut. This is then usually clamped between two walls of highly polished plane parallel surfaces through which a force can be applied. Figure 13(B) illustrates the separation process. Component Y forms a distribution closest to the accumulation wall and is entrained in the lowest laminar flow band. It is gradually separated from component X moving in a faster band of the flow profile. How close the solute particles are to the accumulation wall is determined by the interplay between the applied field and homogeneity-restoring back diffusion. The retention time tr is
233
Determination of Molecular Weights and Their Distributions
Field Outlet
Inlet
Field
Spacer
Channel
(A)
Flow vector
Y
X
w
(B)
Figure 13 (A) Sketch of the basic components in most FFF channels. (B) Distribution of two arbitrary components and the unequal flow displacement velocities for the two species.
given approximately by jFjw tr (61) ¼ t0 6kB T t0 is the void time (the emergence time of a non-retained tracer), w the channel thickness and jFj the strength of the applied field. A separation of two components is only possible when the force increment between the two species is large enough. If an electrical field is applied (electric FFF) particle charge or mobility can be determined. If a centrifuge is used (sedimentation FFF), the effective mass of the solute particles can be determined. A thermal gradient (thermal FFF) correlates with thermal diffusion parameters. A cross-flow of carrier liquid (flow FFF) leads to a particle size determination. Practically, thermal FFF (th-FFF) and flow-FFF (fl-FFF) are of most relevance for the determination of molecular weights and molecular weight distributions. To our best knowledge the sedimentation-FFF has been only used for separation of colloidal particles in the sub mm and micrometer range. A recent review article by Co¨lfen and Antonietti discusses the characterization of polymers and colloids by FFF techniques in great detail including pitfalls and practical examples [66]. Experimental considerations: Th-FFF is driven by a temperature gradient. The channel is usually composed of two metallic blocks (with high heat conductivity, preferably copper) with highly polished even surfaces between which a spacer ( 100 mm) is clamped. The typical dimensions of the metal block are 40–60 cm length, 3–6 cm width, and a thickness of 2–3 cm. The temperature gradient is applied perpendicular to the solvent flow. Usually the upper plate is heated to avoid convection. Often rather high temperature gradients, exceeding 10,000 K/cm are applied, corresponding to temperature differences between the hot and the cold wall of up to 100 K. The thermal diffusion drives the solute particles either more towards the cold or to the warm side with a molecular weight or particle-size dependent penetration length of the concentration distribution into the parabolic channel flow profile, which then leads to a separation of the different molecular
234
Simone Wiegand and Werner Ko¨hler
weight species. In the literature one often finds the statement that the movement of the macromolecules in a temperature gradient is always in the direction from hot to cold [66–68], but this is not always the case [69,70]. In a fl-FFF the bottom wall of the channel consists of an ultrafiltration membrane on top of a porous frit material through which a fraction of the carrier flow exits. This creates a secondary cross flow perpendicular to the primary longitudinal channel flow. The crossflow drives any sample molecule or particle down to the membrane surface. This crossflow-induced drift will be counteracted by Brownian motion so that an exponential concentration distribution layer is established. The thickness of this layer therefore depends on the magnitude of the diffusion coefficients. A slowly diffusing component (high molecular weight) will accumulate relatively closer to the membrane surface than a more rapidly diffusing species because the slow diffusion is less effective in counteracting the crossflow-induced drift. The high molecular weight species therefore travel with lower speed through the channel, resulting in an elution order where components arrange themselves according to decreasing diffusion coefficients, i.e., increasing hydrodynamic size. This retention order is characteristic for sample materials in the submicron size range. A different retention order occurs in fl-/hyperlayer FFF when the particle size exceeds about 1 mm [71]. Often the flFFF technique is a good alternative characterization method for water-soluble polymers [66]. Th-FFF is especially suitable for synthetic polymers in organic solvents in the molecular weight range between M ¼ 104 107 g=mol using temperature differences DT 10 100 K. The list of polymers that have been successfully characterized is as long as for other methods. References to the original works can be found in the recent review by Co¨lfen and Antonietti [66]. From the th-FFF retention data it is possible to obtain a molar mass distribution after a suitable calibration for the determination of the Mark– Houwink–Sakurada constants (straight-line plot of logðD=DT Þ versus log M [72]). The thermal diffusion coefficient DT describes the mass diffusions induced by a temperature gradient [73]. Another possibility is to couple an absolute molar mass detector like a light scattering detector or a suitable detector combination, such as an on-line viscometer coupled with a refractive index detector. This possibility does not require prior knowledge of DT . If copolymer samples are investigated in th-FFF coupled with a viscometer, both the average molecular weight and the average composition are accessible [74]. Th-FFF is also a good technique if polydispersities of very narrow samples from anionic polymerization need to be determined. This was demonstrated for polystyrene from band-broadening data in th-FFF with a higher accuracy than the results obtained by SEC on the same samples [75]. While polymers in the range M ¼ 104 107 g=mol are well resolved by th-FFF, polymers of lower molecular weight (B103 g/mol) need an inconveniently high DT (B150 K) for retention, and problems of boiling solvent, etc. arise. However, successful separations of polystyrene down to 600 g/mol have been described using very high temperature gradients in a pressurized th-FFF channel [76].
Determination of Molecular Weights and Their Distributions
235
FFF and SEC chromatography are largely complementary in application. SEC works best with low molecular weight materials, FFF with high. Both techniques can be combined with different detectors such as multi-angle light scattering, refractive index detection, etc. A major advantage is that for the th-FFF experiment no filtration is required, which always bears the risk of sample loss. For both techniques artefacts due to overloading and sample specific effects like charge interactions as in the case of polyelectrolytes can modify the retention behaviour. Although FFF has essentially a one-phase nature and no stationary phase is present, sample-wall interactions can modify the elution time of the solute. To check for artefacts it is often necessary to run several experiments with the same sample under varying conditions. Nevertheless the FFF family is certainly a flexible analytical technique with a wide molecular weight range from 1,000 up to 1018 g/mol.
7. ANALYTICAL ULTRACENTRIFUGE Though not very widely used today, analytical ultracentrifugation is one of the most fundamental and versatile techniques in polymer analysis [77,78]. Similar to colligative methods and light scattering it rests on a well-established thermodynamic theory without having to resort to questionable a priori assumptions. Furthermore, there are no complicating interactions between the sample and a membrane or a chromatographic column. Under the influence of a gravitational (centrifugal) field, a solute particle of mass m ¼ M=N L immersed in a solvent of density r at a distance r from the rotor axis experiences three forces. Within the frame of reference of the rotor, spinning with angular velocity o, these are the centrifugal force Fc , the buoyant force Fb , and the frictional force Ff : Fc ¼ mo2 r ¼ NML o2 r
(62)
Fb ¼ m0 o2 r ¼ NML v¯ ro2 r
(63)
Ff ¼ fu
(64)
N L is Avogadro’s number, f the particle friction coefficient, u the velocity and v¯ the partial specific volume of the solute [79,80]. Inertial forces are negligible and the balancing of the above forces yields the sedimentation coefficient s¼
u Mð1 v¯ rÞ ¼ o2 r NLf
(65)
In the limit of infinite dilution the friction coefficient can be related to the single particle translational diffusion coefficient D¼
kT f
(66)
236
Simone Wiegand and Werner Ko¨hler
and the Svedberg equation for the molar mass is obtained: s RT (67) D 1 v¯ r Finite concentrations are accounted for by a virial expansion of both D and s1 [12], M¼
leading to
D ¼ D0 ð1 þ kD c þ Þ
(68)
s1 ¼ s1 0 ð1 þ ks c þ Þ
(69)
D 1 uc ð1 v¯ rÞ ¼ RT þ 2A2 c þ s M
(70)
with the second virial coefficient Auc 2 ¼ ðkD þ ks Þ=ð2MÞ. Eventually, sedimentation leads to the build-up of a concentration gradient which gives rise to a diffusion current jD ¼ Drc. In the stationary state jD js ¼ cu ¼ co2 rs, resulting in
(71)
exactly balances the sedimentation current
M¼
RT 1 dlnc ð1 v¯ rÞo2 r dr
(72)
for a dilute solution of a monodisperse polymer. In case of polydisperse solute Equation (72) takes the form dc ð1 v¯ rÞo2 r X ¼ ci Mi dr RT i
(73)
It is rather straightforward to show that proper integration over the cell from the meniscus (rm ) to the bottom (rb ) yields the weight and z-average molar masses Mw and Mz [12]: 1 Z rb rcðrÞdr (74) Mw ¼ ½RTðcðrb Þ cðrm ÞÞ ð1 r¯vÞo2 rm
1 dc dc 1 1 Mz ¼ RT rb rm ð1 r¯vÞo2 ðcðrb Þ cðrm ÞÞ dr b dr m
(75)
All quantities on the right-hand side are experimentally accessible. Experimental considerations: In a modern analytical ultracentrifuge the rotor is equipped with multiple sample cells of 100 mL volume or less and rotates at up to 6 104 revolutions/min, resulting in strong gravitational fields as high as 2:5 105 g. By selection of a proper angular velocity of the rotor, a very broad molar mass range from oligomers (103 g/mol) to high polymers (107 g/mol) can be analyzed. The radial concentration profile is analyzed by detection systems that are synchronized to the revolving rotor. Contrast is generated either by optical absorption of the polymer in the visible or near UV or by a concentration dependent refractive index. Formerly, refractive index changes were detected by
Determination of Molecular Weights and Their Distributions
237
means of Schlieren optics, but today these have been replaced by Rayleigh interferometers [81]. In addition to these traditional detection methods, also fluorescence [82,83] and turbidity [84] detection systems have been developed. A comprehensive treatment of modern ultracentrifugation equipment and applications can be found in the recent book of Ma¨chtle and Bo¨rger [78]. The two main experimental techniques for molar mass determination are the sedimentation velocity run at high rotor speeds and the sedimentation equilibrium run at moderate rotor speeds. In a sedimentation velocity run, s is determined from the sedimentation of the solute in an initially homogeneous solution, which shows up as a sharp boundary moving with the sedimentation velocity u towards the bottom of the cell. D is either obtained from, e.g., DLS experiments, from the diffusive spreading of the sedimentation boundary, or from model calculations or empirical relations between D and M. The partial specific volume v¯ is either measured or calculated. Knowing s, D, and v¯ , the molar mass M is obtained from Equation (67) or from a concentration series according to Equation (70). From a sedimentation velocity experiment the molar mass distribution function (mass fractions) can be determined [12,85,86]. Figure 14 shows the result of a sedimentation velocity experiment on a sample with a very broad particle size distribution, consisting of ten discrete polystyrene dispersions with particle diameters ranging from 67 to 1,220 nm [84]. The smeared-out steps correspond to the transit of the sedimentation front of the respective species through the slit of the detection system. In a sedimentation equilibrium run, the stationary radial concentration profile, which is established after a few hours for a 1-mm column, is analyzed according to Equation (72) or, in case of polydisperse samples, Equations (74) or (75). Contrary to the sedimentation velocity experiment, the diffusion coefficient D is not required. Chemically heterogeneous polymers can be analyzed in a density gradient experiment, where a high-density salt such as CsCl is added. Under the influence of the strong gravitational field the mixed solvent develops a density gradient. The different sample constituents accumulate at the respective positions where their density is matched by the one of the solvent, leading to a characteristic banding of the solution [81]. In addition to the determination of molar mass distributions and various molar mass averages there are many experiments, requiring sometimes sophisticated data evaluation, that can be carried out with an analytical ultracentrifuge. Examples are the analysis of association, the analysis of heterogeneity, the observation of chemical reactions, and protein characterization, to mention only a few. A detailed discussion is beyond the scope of this article, but there is excellent literature available [77–79,81,87–89]
8. OTHER METHODS 8.1 Mass spectrometry In principle, MALDI-TOF (MALDI-Time Of Flight) analysis allows for the determination of the complete polymer mass distributions and, from that, the calculation of various molecular weight averages like Mn and Mw and the
238
Simone Wiegand and Werner Ko¨hler
Figure 14 Particle size distribution of a ten-component mixture of narrow polystyrene dispersions. Left: intensity measured as function of t with a turbidity detector. Right: integral and differential particle size distribution. Reproduced from Ma¨chtle [84] by permission of The Royal Society of Chemistry.
polydispersity D ¼ Mw =Mn. In the case of extremely low polydispersities, the molecular weight distributions can often be measured more exactly than with conventional methods. However, for polydisperse samples the error increases with increasing width of the polymer distribution. Pasch [90] demonstrated that the differences in the determined polydispersities between SEC and MALDITOF are in the range between 2.1% and 11.8% for samples with very low polydispersities between D ¼ 1:04 1:06. These differences increase to 10.6–20.5% and 48–73% when the polydispersities increase to a range of D ¼ 1:08 1:10 and D ¼ 1:4 3, respectively. Molecular weights for very high
Determination of Molecular Weights and Their Distributions
239
molecular weight polymers around 106 can only be determined in case of extremely narrow standards [91] or monodisperse biopolymers [92]. In a standard MALDI-TOF setup polymers with a low polydispersity (D 1:05) and a molecular weight around 15,000 can easily be measured. The problems for the determination of broad distributions functions arise mainly from fragmentation, multiple ionization, and molar mass dependent ionization and desorption probabilities. The strength of mass spectrometry is the chemical characterization of the samples as, for instance, the end group analysis in the case of oligomers or low molecular weight polymers (see Chapter 5). In principle an oligomeric resolution can be obtained. From the absolute mass of each signal of the distribution, the mass of the end groups can be determined using the mass of the repeat unit and the mass of cation used for ionization. This is a fast way to verify expected end groups after a polymerization or functionalization. Therefore, MALDI-TOF mass spectrometry has gained popularity in end group analysis over the traditional methods such as NMR, IR, UV, elemental analysis, or titration techniques. It needs to be pointed out, that the investigation of some technically important polymers like polyolefines has not been very successful so far. Owing to their inert nature they are difficult to dissolve and also difficult to ionize. Typically one needs for the ionization process some heterogeneities or double bonds in the polymer. For some insoluble substances a solvent-free sample preparation method has been developed that allows a characterization by MALDI-TOF mass spectrometry [93]. For polydisperse samples a combination of SEC and mass spectrometry is ideal. In practice three different approaches have been realized: on-line systems, ‘‘on-line’’ set-up via interface and off-line systems. In principle the mass spectrometer can be used as an on-line detector. The problem is, that MALDITOF is based on the pulsed desorption of molecules from a solid surface in the gas phase and, therefore, it is a priori not compatible with liquid chromatography. For practical purposes it turns out that the method is limited to fairly low molecular weights (Mo2000 g/mol) because polymers with higher masses break down into fragments during the ionization process [94–96]. This problem can be overcome by the use of such automated interfaces as the LC interface or PROBOT interfaces [90]. Using the off-line method the sample is pre-fractionated by SEC and then the resulting narrow fractions are analyzed by MALDI-TOF. A combination of SEC and mass spectrometry has frequently been used and many examples are discussed in the excellent book by Pasch and Schrepp on MALDITOF mass spectrometry of synthetic polymers [90]. In this book the interested reader finds also many technical details on matrix/solvent combinations, which have been successfully used for various polymers.
8.2 Nuclear magnetic resonance NMR allows the determination of molecular weight by near end [97] or end groups [98]. The method is limited to rather low molecular weights below 3 104 g/mol, because for higher molecular weight the number of end groups eventually
240
Simone Wiegand and Werner Ko¨hler
diminish to the point where a quantitative determination becomes impractical. On the basis of the intensities of the peaks characteristic for the end group or near end groups the number of end groups can be determined. If the polymer is completely linear, quantitative determination of all end groups provides a direct measure of the number of molecules present and hence of the number average molecular weight Mn . In very few cases solid-state NMR has been used to determine molecular weights for polyethylene [99]. In general solid-state NMR is not so suitable due to the long relaxation times of the end groups, which lead to long measurement times. The strength of NMR is in chemical structure characterization and also the possibility to determine the chain branching, tacticity or to obtain further details of the microstructure.
8.3 Infrared spectroscopy With infrared spectroscopy the molecular composition of polymers is determined by analyzing the characteristic vibrations of functional groups. IR spectroscopy is one of the traditional end group characterization techniques and allows, as with NMR spectroscopy, the determination of number averaged molecular weight Mn for low molecular weight polymers. But its strength is the possibility to analyze the microstructure of polymers and their relationship with macroscopic properties. Often the concentration signal in the SEC separation process is detected by an IR detector. Technically important is the characterization of polyolefines, here the detector is connected to a high-temperature SEC. IR spectroscopy is seldomly used for pure molecular weight determination.
8.4 Electrophoresis Capillary electrophoresis has been very successfully applied for separation of proteins and carbohydrates, and in DNA sequencing. So far very little work has been reported on the separation of synthetic or industrial polyelectrolytes. It has been demonstrated that capillary electrophoresis is a useful technique to separate synthetic anionic and cationic polymers, such as polystyrenesulfonic acid or polyvinylypyridinium hydrochloride in the molecular weight range between 1.5 and 1,500 kg/mol [100–103]. In the case of neutral water-soluble synthetic polymers such as polyethylene glycols most of the separations reported in the literature are limited to the oligomeric range (up to molar masses around 10 kg/mol). For all macromolecules the electrophoretic migration needs to be modified by exclusion or sieving, because for large molecules the electrophoretic mobility becomes independent of the size. Owing to the wide variety of shapes, architectures, sizes, and chemical properties, the capillary electrophoresis often has to be uniquely tailored for the polymer [5], which requires a lot of time and experience. Recent reviews [3–5] give an overview on the progress of the separation of synthetic macromolecules by capillary electrophoresis in the recent years. Technical details and pitfalls in the everyday analytical practice are discussed in the book by Engelhardt [104].
Determination of Molecular Weights and Their Distributions
241
Capillary electrophoresis has also been combined with other analytical methods like mass spectrometry, NMR, Raman, and infrared spectroscopy in order to combine the separation speed, high resolving power and minimum sample consumption of capillary electrophoresis with the selectivity and structural information provided by the other techniques [6].
9. PRACTICAL EXAMPLES 9.1 Characterization of rigid-rod polymers Typically, characterization of a new polymer cannot be accomplished by a single measurement with one particular apparatus. Especially for polymers where no standards with narrow molar mass distributions exist, in most cases a combination of different experimental techniques is necessary for a satisfactory characterization. For such materials, very often additional information besides the pure molar mass distribution, e.g., the persistence length, is required. In the following we will discuss the characterization work for a rigid-rod poly (p-phenylene) (Figure 15), which had been synthesized with nine different degrees of polymerization (fractions), named P1–P9 [30]. Owing to the very low conformational entropy of stiff polymers, sulfonate ester and dodecyl side chains had to be added for sufficient solubility. These rigid-rod polymers served as precursors for highly charged polyelectrolytes, which can undergo self-assembly into micellar super-molecular aggregates [44,105,106]. Since there were neither narrow calibration standards available nor Mark– Houwink–coefficients known, a simple chromatographic measurement of the molar mass distribution with concentration detection was not feasible. In a first step, static light scattering and membrane osmometry were employed to obtain model-free values for Mw and Mn . Zimm plots similar to the one in Figure 8 were constructed for the evaluation of the light scattering data according to Equation (42), which additionally yields the radius of gyration hRg iz and the second virial coefficient A2 (Table 3). Membrane osmometry measurements were carried out with the capillary osmometer shown in Figure 3. Owing to the short equilibration time of the instrument and the low cut-off molar mass of the membrane, solute permeation through the membrane, which would show up as a drift of the baseline, did not cause problems even for the lowest molar mass fraction. Mn was obtained from
CH3
SO2 R
t−Bu R= n
C12 H 15
Figure 15
SO2 R
t−Bu
Poly(p-phenylene) with side-groups for improved solubility [30].
242
Simone Wiegand and Werner Ko¨hler
1=2
Table 3 Light scattering (Mw , hR2g i ), membrane osmometry (Mn), and viscosity ([Z]) data for the nine poly(p-phenylene) fractions P1–P9 Fraction
P1 P2 P3 P4 P5 P6 P7 P8 P9
Mn
[Z]
(kg/mol)
hR2g i1=2 (nm)
(kg/mol)
(mL/g)
189 157 113 101 90 64 40 38 27
45.6 40.2 29.7 33.0 29.4 19.4 15.7 – –
99 76 54 48 36 39 22 23 16.5
331 275 180 176 127 125 67 78 45
Mw
the concentration dependence of the osmotic pressure for every fraction according to Equation (28). With the aim to establish an ½Z–M relation (Equation (36)) for universal calibration and for the determination of the persistence length, intrinsic viscosities were measured with an Ubbelohde capillary viscometer. The respective data are also included in Table 3. Strictly speaking, monodisperse samples would be required for the determination of the Mark–Houwink coefficients. Since, however, the polydispersities of the nine individual fractions are only moderate (Mw =Mn 2) and since both Mw and ½Z are measured as weight averages with the same statistical weights, the error introduced by the incorrect treatment of the polydispersity could be neglected. Scaling laws like Equation (36) for semiflexible rigid-rod polymers with persistence length lp can only be expected in the rigid-rod limit for short chains with lm l lp , l being the contour length and lm being the length of a monomer unit, and in the flexible coil limit for long chains with l lp . For intermediate chain lengths Equation (41) gives a more adequate description of a semiflexible polymer. In Ref. [30] it has been shown that, for the limited molar mass range of the samples investigated, both equations can equally well be used for universal calibration of the SEC. The apparent scaling factor a 0:96 is expected to be molar mass dependent and will eventually approach 0.5–0.8 in the high polymer limit. Figure 16 shows the molar mass distributions of polymer P3 after universal calibration based on Equations (36) and (41), which are almost indistinguishable. The polystyrene calibration yields significantly too high molar masses, since it strongly overestimates the flexibility of the polymer chain. In Ref. [30] the consistency of the approach is demonstrated by recalculating the respective molar mass averages Mw and Mn of the nine polymer fractions from the SEC elugrams after universal calibration, which agree very well with the
Determination of Molecular Weights and Their Distributions
243
wi / g
1.0
0.5
0.0
3
4
5
6
log (Mi / g mol-1) Figure 16 SEC molar mass distribution of poly(p-phenylene) P3 in THF after universal calibration based on Equations (31) (dashed) and (36) (dotted) and with polystyrene calibration (solid line).
absolute values measured by light scattering and membrane osmometry. In particular the Mn values, which had not been used for establishing the universal calibration, show a remarkable agreement. From the two parameters AZ and BZ in Equation (41) a persistence length of lp ¼ 13 nm could be derived.
9.2 Scaling laws Many polymer properties can be expressed as power laws of the molar mass. Some examples for such scaling laws that have already been discussed are the scaling law of the diffusion coefficient (Equation (57)) and the Mark–Houwink– Sakurada equation for the intrinsic viscosity (Equation (36)). Under certain circumstances scaling laws can be employed advantageously for the determination of molar mass distributions, as shown by the following two examples.
9.2.1 Dynamic light scattering In Ref. [107] it has been demonstrated how, based on the scaling law for the diffusion coefficient, molar mass distributions can be calculated from time correlation functions obtained from scattering experiments. DLS is a versatile experimental technique, which is readily available in many laboratories. As discussed in Section 5.2, the field autocorrelation function gð1Þ ðtÞ
244
Simone Wiegand and Werner Ko¨hler
(Equation (51)) contains all information about the distribution function GðGÞ of the decay rates G ¼ Dq2 (Equation (52)). GðGÞ is obtained from an inverse Laplace transform of Equation (51). The computation of GðGÞ is a rather difficult task and a short discussion has been given in Section 5.2. In order to calculate the molar mass distribution, the scaling law (Equation (52)) G ¼ aMb needs to be known. Since the intensity of the light scattered by all molecules of molar mass M and concentration c(M) is proportional to the z-statistical weight c(M)M, the molar mass distribution in concentration units is obtained as [107] cðMÞ / GðGðMÞÞMa j
dGðMÞ j / GðGðMÞÞM1ba dM
(76)
with a ¼ 1 in case of DLS. In Ref. [107] the procedure above has been employed for the measurement of the molar mass distribution of a broad molecular weight polystyrene, obtained by radical polymerization with ethylacetate as solvent. The scaling parameters for this polystyrene in this marginal solvent have been determined to be a 2:8 104 cm2 =s and b 0:52 [107]. The upper curve in Figure 17 shows the resulting molar mass distribution in comparison with the one obtained by SEC. The weak signal contributions from the short polymer chains and problems associated with the inverse Laplace transform usually lead to significant deviations of the thus determined molar mass distribution. Some of these problems, but not all, can be avoided by utilizing the transient holographic grating technique of TDFRS, where a more even signal contribution from the different molar masses can be achieved. Depending on the way the experiment is performed, the parameter a in Equation (76) is either a ¼ 0 for short exposure times (tp ¼ 0:05 s in Figure 17) or a ¼ b for long exposure times (tp ¼ 2 s in Figure 17). The molar mass distributions are reasonable approximations of the one obtained by the fractionating technique, however they exhibit an erroneous bimodal structure, which results from problems with the Laplace inversion by means of the CONTIN method [48,49]. Table 4 summarizes the various molar mass averages obtained by the different dynamic scattering techniques and by the fractionating SEC method. There is a good agreement between all methods for Mw, whereas Mn is obviously overestimated by DLS and by the long exposure TDFRS. The large differences for Mz are difficult to interpret, since SEC with a concentration detector may also not have sufficient sensitivity in the high-M tail of the distribution.
9.2.2 Analytical ultracentrifuge A nice example for the utilization of scaling laws in sedimentation velocity runs with the analytical ultracentrifuge has been published by Ma¨chtle and Bo¨rger [78]. For the polyelectrolyte sodium polystyrene sulfonate (NaPSS) in 0.5 molar NaCl solution they found a scaling law for the sedimentation coefficient at
Determination of Molecular Weights and Their Distributions
245
3
PCS
c(M)
2
τp=2s
1
τp=0.05s
0
103
104
105
106
107
M / g mol-1
Figure 17 Molar mass distributions of polystyrene in ethyl acetate obtained by dynamic light scattering (photon correlation spectroscopy, PCS) and TDFRS with short and long exposure time tp . The dashed curves represent the distribution as determined by SEC. Reproduced with permission from Rossmanith and Ko¨hler [107]. Copyright 1996 American Chemical Society.
Table 4 Molar mass averages (in kg/mol) calculated from the molar mass distributions obtained by SEC, short and long exposure TDFRS, and DLS
Mn Mw Mz
SEC
TDFRS (0.05 s)
TDFRS (2 s)
57 285 640
58 237 434
107 275 509
DLS
121 262 1,229
Source: From [107].
infinite dilution: s0 ¼ KMa ¼ 0:024½SM0:46
(77)
[S] denotes the Svedberg unit (1013 s). Once such a scaling law is available, it can be used in conjunction with a rapid measurement of the sedimentation coefficient
246
Simone Wiegand and Werner Ko¨hler
in the dilute limit, from which M is immediately obtained from the inversion of Equation (77): M ¼ ðs0 =KÞ1=a . The more time-consuming task is the establishment of the scaling law, which requires a series of polymer samples of narrow molar mass distribution and known molar mass. Their sedimentation coefficients have to be measured as a function of concentration and extrapolated back to c ¼ 0 in order to obtain s0 ðMÞ (Figure 18). The same authors then discuss the determination of the entire molar mass distribution from sedimentation velocity runs via scaling laws for the polymer polystyrene in cyclohexane, where the scaling law is also known [78]: s0 ¼ 0:01343½SM0:50
(78)
The procedure first requires the determination of apparent integral sedimentation distribution functions at different scanning times from the time-dependent concentration profiles. These are then corrected for diffusion and finite concentration effects by extrapolating to infinite scanning time and zero concentration to obtain the integral sedimentation distribution GðsÞ and its derivative, the differential sedimentation distribution gðsÞ. Since a concentration sensitive detector has been employed, the molar mass distribution in terms of weight fractions, wðMÞ, is finally calculated utilizing the scaling relation Equation (78): ds (79) wðMÞ ¼ gðsÞ dM
Figure 18 Scaling law of sedimentation coefficient s0 for NaPSS. Measurements of s at finite concentrations (left) and plot of s0(M) (right). Reproduced with permission from Ma¨chtle and Bo¨rger [78].
Determination of Molecular Weights and Their Distributions
247
Mathematically, this procedure is very similar to the one discussed above for the DLS case.
10. CONCLUSION With this chapter we have tried to provide an overview of experimental techniques for determining molecular weight averages and molecular weight distributions. All methods discussed here have their specific advantages and weaknesses and differ very much in their complexity. The choice of the ‘best’ method strongly depends on polymer properties, the information needed for a particular purpose, and on the available resources. Yet another aspect in the analytical characterization of polymers may be speed. Under certain circumstances some methods are superior compared to others. Vapour pressure osmometry, for instance, works well for low molecular weight, while FFF techniques and light scattering work better for high molecular weight polymers. SEC can be used over a very broad molecular weight range, but calibration and solute interaction with the column material may be a problem. Typically, the operating expense for the characterization grows with the complexity (heterogeneity) of the polymer. For a crude estimation, one might differentiate between four different classes of polymers: 1. 2. 3. 4.
simple homopolymers where monodisperse standards are available homopolymers where no monodisperse standards are available water soluble polymers and polyelectrolytes copolymers (random, diblock, triblock)
Simple homopolymers, where monodisperse standards and suitable solvents are available, are easily characterized by SEC. Homopolymers for which no monodisperse standards are available additionally require some more elaborate detection system for transformation of the retention time into molecular weight. This can be done by, e.g., universal calibration. Alternatively, an absolute molar mass detector, like an on-line light scattering detector or mass spectrometer, can be used. If only average values are of interest, non-fractionating absolute techniques like light scattering and osmometry may be adequate. Ultracentrifugation can provide both a number of different averages and the distribution function, but it is expensive and its availability is limited to a small number of laboratories. In production control it might be sufficient to know the relative mass compared to previous batches. In those cases a chromatographic technique without absolute calibration, or even viscosity measurements, may be sufficient. Water-soluble polymers in general, and especially polyelectrolytes, are often difficult due to their specific and long range electrostatic interactions, which complicate all analytical techniques that rely on single particle properties that are usually realized by high dilution. In most cases the ionic strength of the solution must be increased by the addition of salt in order to screen electrostatic forces. Ideally, SEC separation is predominantly governed by entropic interactions,
248
Simone Wiegand and Werner Ko¨hler
but in the case of highly polar water-soluble polymers enthalpic interactions with the column frequently become important. Often the fl-FFF technique is a good alternative characterization method for water-soluble polymers. Nevertheless, also in this case it is necessary to check whether polymer–polymer or polymer– wall interactions lead to artefacts. Additionally, one needs to select the carrier fluid carefully. Most challenging is the characterization of complex polymers, which are heterogeneous in more than one distributed property, as for instance copolymers. For such complex polymers one cannot follow a simple recipe, but rather one needs to resort to a polymer-specific measurement scheme. Often complex polymers require a combination of different analytical techniques. One approach can be to separate the compounds according to their chemical composition and in the second step to determine the molecular weight distribution or vice versa. Here the two- or multidimensional chromatographic techniques are extremely useful. Some of the detectors, for example, a light scattering detector or a membrane osmometer, can be built in as on-line detectors, but many of these combinations are not commercially available and, thus, mainly limited to larger research laboratories. Other detectors, like a mass spectrometer, may require a special interface or off-line sample collection. We hope that this chapter on the molecular weight determination of synthetic polymers has illustrated that in the case of a complex polymer it is preferable to use several experimental methods for the molecular weight determination to obtain a full picture. Owing to the different sensitivity of the various methods some are blind for low molar masses while others are blind at low concentrations. As exemplified, often scaling laws can be utilized to compare results of different methods and different sensitivities.
ACKNOWLEDGEMENTS We are grateful for fruitful discussions with Dieter Lilge, Katja Klimke, Wolfgang Radke, Hans Joachim Ra¨der, and Manfred Wilhelm. We thank Malte Kleemeier and Adam Patkowski for carefully reading the manuscript and their constructive criticism.
REFERENCES 1 2 3 4 5 6 7 8 9 10
H. Staudinger and W. Heuer, Ber. dtsch. chem. Ges., 63 (1930) 222. H. Staudinger and W. Nodzu, Ber. dtsch. chem. Ges., 63 (1930) 721. H. Engelhardt and O. Grosche, Adv. Polym. Sci., 150 (2000) 189. H. Engelhardt and M. Martin, Adv. Polym. Sci., 165 (2004) 211. H. Cottet, C. Simo, W. Vayaboury and A. Cifuentes, J. Chromatogr. A, 1068 (2005) 59. Analysis and detection by capillary electrophoresis, Vol. XLV of Comprehensive analytical chemistry, edited by M. L. Marina, A. Ro´s, and M. Valcrucel (Elsevier, Amsterdam, 2005). H.-G. Elias, Makromoleku¨le, Vol. 1, Hu¨thig & Wepf, Basel, 1990. J.C. Thomas, J. Colloid Interf. Sci., 117 (1986) 187. H.-G. Elias, Macromolecules, Vol. 1, Wiley-VCH, Weinheim, 2005. (22) IFF-Ferienkurs, Physik der Polymere, Forschungszentrum Ju¨lich, Ju¨lich, 1991.
Determination of Molecular Weights and Their Distributions
249
11 E. Schro¨der, G. Mu¨ller and K.-F. Arndt, Polymer Characterization, Hanser Publications, Munich, 1989. 12 K.-F. Arndt and G. Mu¨ller, Polymercharakterisierung, Hanser, Mu¨nchen, 1996. 13 W.H. Stockmayer and E.F. Casassa, J. Chem. Phys., 20 (1952) 1560. 14 P.E. Slade (Ed.), Polymer Molecular Weights, Marcel Dekker, New York, 1975. 15 W.W. Yau, J. Appl. Polymer Sci.: Appl. Polym. Symp., 48 (1991) 85. 16 U. Lehmann, W. Ko¨hler and W. Albrecht, Macromolecules, 29 (1996) 3212. 17 W. Albrecht, Th. Weigel, K. Kneifel, U. Lehmann, W. Ko¨hler and D. Paul, Acta Polym., 49 (1998) 184. 18 A.J. Staverman, D.T.F. Pals and C.A. Kruissink, J. Polym. Sci., 23 (1957) 57. 19 B. Widera, R. Neueder and W. Kunz, Langmuir, 19 (2003) 8226. 20 A. Kastanek, M. Bohdanecky´ and S. Podzimek, Eur. Polym. J., 41 (2005) 319. 21 S. Acevedo, L.B. Gutierrez, G. Negrin, J.C. Pereira, B. Mendez, F. Delolme, G. Dessalces and D. Broseta, Energy Fuels, 19 (2005) 1548. 22 P.F. Onyon, In: P. Allen (Ed.), Polymer Characterization, Butterworths scientific publications, London, 1959, p. 171. 23 J. Bandrup and E. Immergut (Eds.), Polymer Handbook, 3rd ed., Wiley, New York, 1989. 24 J.R. Van Wazer, J.W. Lyons, K.Y. Kim and R.E. Colwell, Viscosity and Flow Measurements, Interscience Publishers, New York, 1963. 25 G.V. Schulz and F.J. Blaschke, Prakt. Chem., 158 (1941) 130. 26 M.L. Huggins, J. Am. Chem. Soc., 64 (1942) 2716. 27 E.O. Kraemer, Ind. Eng. Chem., 30 (1938) 1200. 28 W. Burchard, Adv. Polym. Sci., 143 (1999) 113. 29 M. Bohdanecky´, Macromolecules, 16 (1983) 1483. 30 S. Vanhee, R. Rulkens, U. Lehmann, C. Rosenauer, M. Schulze, W. Ko¨hler and G. Wegner, Macromolecules, 29 (1996) 5136. 31 M.B. Huglin, Light Scattering from Polymer Solutions, Academic Press, Inc, New York, 1972. 32 P. Kratochvil, Classical Light Scattering from Polymer Solutions, Vol. 5 of Polymer Science Library, Elsevier, Amsterdam, 1987. 33 C.S. Johnson and D.A. Gabriel, Laser Light Scattering, Dover, New York, 1981. 34 B.H. Zimm, J. Chem. Phys., 16 (1948) 1099. 35 A. Becker, W. Ko¨hler and B. Mu¨ller, Ber. Bunsenges. Phys. Chem., 99 (1995) 600. 36 T.M. Bender, R.J. Lewis and R. Pecora, Macromolecules, 19 (1986) 244. 37 E. Moreels, W. Deceuninck and R. Finsy, J. Chem. Phys., 86 (1987) 618. 38 G. Berth, H. Dautzenberg, B.E. Christensen, S.E. Harding, G. Rother and O. Smidsrod, Macromolecules, 29 (1996) 3491. 39 P. Kratochvil, Pure Appl. Chem., 54 (1982) 379. 40 G.C. Berry, J. Chem. Phys., 44 (1966) 4550. 41 I.A. Katime and J.R. Quintana, Polymercharacterization, Vol. 1 of Comprehensive Polymer Science, Pergamon Press, Oxford, 1989, 103pp. 42 J.K.G. Dhont, An introduction to Dynamics of Colloids, Elsevier, Amsterdam, 1996. 43 B.J. Berne and R. Pecora, Dynamic Light Scattering, Wiley, New York, 1976. 44 M. Bockstaller, W. Ko¨hler, G. Wegner, D. Vlassopoulos and G. Fytas, Macromolecules, 34 (2001) 6359. 45 D.E. Koppel, J. Chem. Phys., 57 (1972) 4814. 46 J.C. Brown, P.N. Pusey and R. Dietz, J. Chem. Phys., 62 (1975) 1136. 47 B.J. Frisken, Appl. Optics, 40 (2001) 4087. 48 S.W. Provencher, Comput. Phys. Commun., 27 (1982) 213. 49 S.W. Provencher, Comput. Phys. Commun., 27 (1982) 229. 50 P. Sˇteˇpa´nek, In: W. Brown (Ed.), Dynamic light Scattering, Clarendon Press, Oxford, 1993, p. 177. 51 J. Honerkamp, D. Maier and J. Weese, J. Chem. Phys., 98 (1993) 865. 52 R.S. Stock and W.H. Ray, J. Polym. Sci., Part B: Polym. Phys., 23 (1985) 1393. 53 R.G. Kirste, W.A. Kruse and K. Ibel, Polymer, 16 (1975) 120. 54 J.S. Higgins and H.C. Benoit, Polymers and Neutron Scattering, Vol. 8 of Oxford Series on Neutron Scattering in Condensed Matter, Clarendon Press, Oxford, 1994.
250
Simone Wiegand and Werner Ko¨hler
55 W. Ko¨hler and R. Scha¨fer, Adv. Polym. Sci., 151(II) (2000) 1. 56 W. Yau, J.J. Kirkland and D. Bly, Modern Size-Exclusion Liquid Chromatography, Wiley, New York, 1979. 57 H. Pasch, Adv. Polym. Sci., 150(I) (2000) 1. 58 E. Ron, E. Mathiowitz, G. Mathiowitz, A. Domb and R. Langer, Macromolecules, 24 (1991) 2278. 59 H. Pasch, Adv. Polym. Sci., 128 (1997) 1. 60 H. Pasch, M. Adler, F. Rittig and S. Becker, Macromol. Rapid Commun., 26 (2005) 438. 61 S.J. Kok, C.A. Wold, T. Hankemeier and P.J. Schoenmakers, J Chromatogr. A, 1017 (2003) 83. 62 J.N. Willis, J.L. Dwyer and M.X. Liu, Int. J. Polym. Anal. Character., 4 (1997) 21. 63 M. Hakkarainen, A.C. Albertsson and S. Karlsson, J. Appl. Polym. Sci., 66 (1997) 959. 64 J. Kylma and J.V. Seppala, Macromolecules, 30 (1997) 2876. 65 G.W. Somsen, E.J.E. Rozendom, C. Gooijer, N.H. Velthorst and U.A.T. Brinkman, Analyst, 121 (1996) 1069. 66 H. Co¨lfen and M. Antonietti, Adv. Polym. Sci., 150(I) (2000) 67. 67 J.C. Giddings, M. Martin and M.N. Myers, Separation Sci. Technol., 14 (1979) 611. 68 M. Martin and R. Reynaud, Analyt. Chem., 52 (1980) 2293. 69 M. Giglio and A. Vendramini, Phys. Rev. Lett., 38 (1977) 26. 70 B.J. de Gans, R. Kita, S. Wiegand and J. Luettmer-Strathmann, Phys. Rev. Lett., 91 (2003) 245501. 71 S.K. Ratanathanawongs and J.C. Giddings, Analyt. Chem., 64 (1992) 6. 72 M.N. Myers, P. Chen and J.C. Giddings, In: T. Provder (Ed.), Chromatography of Polymers: Characterization by SEC and FFF, American Chemical Society, Washington, DC, 1993, p. 47. 73 S. Wiegand, J.Phys., Condens. Matter, 16 (2004) R357. 74 M.E. Schimpf, In: T. Provder, H. Barth and M. Urban (Eds.) (Eds.), Chromatographic Characterization of Polymers: Hyphenated and Multidimensional Techniques, American Chemical Society, Washington, DC, 1995. 75 M.E. Schimpf, M.N. Myers and J.C. Giddings, J. Appl. Polym. Sci., 33 (1987) 117. 76 J.C. Giddings, L.K. Smith and M.N. Myers, Analyt. Chem., 47 (1975) 2389. 77 S.E. Harding, A.J. Rowe and J.C. Horton (Eds.), Analytical Ultracentrifugation in Biochemistry and Polymer Science, Royal Society of Chemistry, Cambridge, 1992. 78 W. Ma¨chtle and L. Bo¨rger, Analytical Ultracentrifuation, Springer Laboratory, Springer, Berlin, 2006. 79 G. Ralston, Introduction to analytical ultracentrifugation, Beckman technical note. 80 C. Tanford, Physical Chemistry of Macromolecules, Wiley, New York, 1961. 81 H. Co¨lfen, In: R.A. Lessard and H. Franke (Eds.), Materials Characterization and Optical Probe Techniques, Critical Reviews of Optical Science and Technology, SPIE, San Diego, 1997. 82 B. Schmidt and D. Riesner, A fluorescence detection system for the analytical ultracentrifuge and its application to proteins, nucleic acids, viroids and viruses (in Ref. [77]). 83 T.M. Laue, J.B. Austin and D.A. Rau, Prog. Colloid Polym. Sci., 131 (2006) 1. 84 W. Ma¨chtle, Analysis of polymer dispersions with an eight cell-AUC-multiplexer: high resolution particle size distribution and density gradient techniques (in Ref. [77]). 85 J.-H. Kehrhahn and M.D. Lechner, Polymer, 34 (1993) 2447. 86 S.E. Harding, Carbohydr. Res., 340 (2005) 811. 87 J. Li, K.D. Caldwell and W. Ma¨chtle, J. Chromatogr., 517 (1990) 361. 88 W. Ma¨chtle, Angew. Makromol. Chem., 162 (1988) 35. 89 W. Ma¨chtle, Colloid Polym. Sci., 262 (1984) 270. 90 H. Pasch and W. Schrepp, MALDI-TOF Mass Spectrometry of Synthetic Polymers, Laboratory Series in Polymer Science, Springer, Berlin, 2003. 91 D.C. Schriemer and L. Li, Analyt. Chem., 68 (1996) 2721. 92 K. Martin, J. Spickermann, H.J. Ra¨der and K. Mu¨llen, Rapid Commun. Mass Spectrom., 10 (1996) 1471. 93 S. Trimpin, A.C. Grimsdale, H.J. Ra¨der and K. Mu¨llen, Analyt. Chem., 74 (2002) 3777. 94 M.L. Vestal, Mass Spectrom. Rev., 2 (1983) 447. 95 J.D. Vargo and K.L. Olson, Analyt. Chem., 57 (1985) 672. 96 J.D. Vargo and K.L. Olson, J. Chromatogr., 353 (1986) 215. 97 K.J. Liu, Makromol. Chemie-Macromol. Chem. Phys., 116 (1968) 146.
Determination of Molecular Weights and Their Distributions
251
98 J.T. Xu, W. Jin and Z.Q. Fan, J. Appl. Polym. Sci., 98 (2005) 208. 99 M. Pollard, K. Klimke, R. Graf, H.W. Spiess, M. Wilhelm, O. Sperber, C. Piel and W. Kaminsky, Macromolecules, 37 (2004) 813. 100 J.B. Poli and M.R. Schure, Analyt. Chem., 64 (1992) 896. 101 H. Cottet, P. Gareil and J.L. Viovy, Electrophoresis, 19 (1998) 2151. 102 H.N. Clos and H. Engelhardt, J. Chromatogr. A, 802 (1998) 149. 103 O. Grosche, J. Bohrisch, U. Wendler, W. Jaeger and H. Engelhardt, J. Chromatogr. A, 894 (2000) 105. 104 H. Engelhardt, W. Beck and S. Th, Kapillarelektrophorese, Vieweg, Braunschweig, 1994. 105 M. Bockstaller, W. Ko¨hler, G. Wegner, D. Vlassopoulos and G. Fytas, Macromolecules, 33 (2000) 3951. 106 M. Bockstaller, W. Ko¨hler, G. Wegner and G. Fytas, Macromolecules, 34 (2001) 6353. 107 P. Rossmanith and W. Ko¨hler, Macromolecules, 29 (1996) 3203.
This page intentionally left blank
SECTION III: Polymer Morphology and Structure
This page intentionally left blank
CHAPT ER
7 Phase Structure and Morphology Rufina G. Alamo
Contents
1. Phase Structure and Morphology 1.1 Phase structure 1.2 Characterization of the liquid-like phase 1.3 Characterization of the interphase 2. Supermolecular Morphology 2.1 Lamellar thickness 3. Concluding Remarks Acknowledgements References
255 257 267 271 274 284 286 287 287
1. PHASE STRUCTURE AND MORPHOLOGY The properties of semi-crystalline polymers are very dependent on the chain microstructure and the crystalline morphology adopted upon crystallization or on processing. The well-known fact that crystallinity controls the properties of these materials raised interest in investigating the details of the liquid–solid transformation, and the degree and type of chain organization, from early stages and in parallel with the development of polymer science. In this chapter we will describe in some detail the fundamental elements of the semi-crystalline structure, the large-scale macromolecular organization and most customary methods of characterization of crystalline and non-crystalline regions. For polymer molecules to adopt long-range three-dimensional order, they must have both a high degree of chemical regularity and a high degree of relative motion in the melt.1 A major difference between the crystalline state developed by long-chain molecules and that of small organic molecules, metals or ceramics is inherent to the covalent connectivity between repeating units in a polymer molecule. While individual atomic or low molecular weight species 1
Some polymers with a high degree of chemical regularity and high glass transition temperatures degrade before crystallization. For example, PES [poly(aryl ether sulfone)] is chemically regular but essentially amorphous.
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00407-8
r 2008 Elsevier B.V. All rights reserved.
255
256
Rufina G. Alamo
occupy equivalent points in each unit cell, in long-chain polymers the covalent connectivity of repeating units sets a unique correspondence to perpetuate crystallographic symmetry. The continuity of long-chain molecules impacts in a very unique way the structure and morphology that evolves from the initial complex melt. The pioneering works of Storks [1] and Keller [2] established that lamellar crystallites are the fundamental three-dimensional entities that develop upon crystallization of chain molecules from solution or from the melt. The widespread observation of lamellar crystallites, with the chain axis preferentially oriented normal to the basal plane with thicknesses much lower than the contour length of the molecule, represented a major advance in the understanding of the morphological features of crystalline polymers [3–7]. The molecules fold back and forth and, except for the very low molecular weight polymers, may traverse a crystallite many times and connect two or more lamellae. This molecular connectivity is a unique feature of polymer crystallization. It defines the amorphous interlamellar or liquid-like region as well as the interfacial region in which the order of the chains emanating from the crystalline phase is dissipated [8]. The crystallization process of flexible long-chain molecules is rarely if ever complete. The transition from the entangled liquid-like state where individual chains adopt the random coil conformation, to the crystalline or ordered state, is mainly driven by kinetic rather than thermodynamic factors. During the course of this transition the molecules are unable to fully disentangle, and in the final state liquid-like regions coexist with well-ordered crystalline ones. The fact that solid- (crystalline) and liquid-like (amorphous) regions coexist at temperatures below equilibrium is a violation of Gibb’s phase rule. Consequently, a metastable polycrystalline, partially ordered system is the one that actually develops. Semicrystalline polymers are crystalline systems well removed from equilibrium. The crystalline state of polymers can be described by a set of hierarchical structures. At the most fundamental level there is the unit cell or primary crystallographic repeated unit. Increasing complexity and, at a larger-scale level, the polymeric lamellae integrate the long-chain connectivity between crystalline and non-crystalline regions. It is in the crystalline regions where the repeated symmetry of continuous crystallographic units is found. The next level of organization corresponds to lamellar aggregates or supermolecular structures. At this level spherical aggregates (spherulites) of different degrees of order are most often found [9–12]. The crystalline lamellae are an important feature of the semicrystalline structure. A schematic representation of the lamellae for a meltcrystallized system is given in Figure 1. The figure displays the coexistence of the three major phases, crystalline, liquid-like and interfacial. Most macroscopic properties are a direct function of the relative content of these phases. Diverse viewpoints about the character of these phases and conformational details of chain units connecting crystallites have evolved historically and can be found in a series of reviews [13–33]. Interest in understanding the details of the crystalline structure arises from the fact that crystallinity controls the properties of semi-crystalline polymeric materials. The characterization of each of the phases of the structure has long
Phase Structure and Morphology
257
Crystalline Interfacial Amorphous
Figure 1 Semi-crystalline lamellae. Crystalline, interfacial and liquid-like (amorphous) regions are indicated.
been of scientific and technological research interest and many techniques and different analyses have been used and improved in the last three decades to define and quantify these phases.
1.1 Phase structure 1.1.1 Characterization of the crystalline phase Related to the ordered crystalline region of primary interest is the fractional content of material that is truly crystalline. Standard measurements of the crystallinity level include wide-angle X-ray scattering (WAXS) [34], density measurements [35], differential scanning calorimetry (DSC) [36,37] and Raman, infrared (IR) and nuclear magnetic resonance (NMR) spectroscopies [38–40]. Depending on the technique used, the measurement involves determination of a volume- or mass-based fraction of crystalline material. The early information obtained from most of these techniques was analyzed following a structural model for semi-crystalline polymer consisting of two phases, crystalline and liquid-like [41]. Recognizing the need for a phase of intermediate order, the determination of the degree of crystallinity was revisited to include a more complex three-phase system [42].
258
Rufina G. Alamo
1.1.2 X-ray diffraction The use of wide-angle X-ray diffraction (WAXD) to obtain the degree of crystallinity involves the analysis of a discrete set of crystalline reflections (Bragg spacings) that are superposed upon a broad amorphous halo. The crystallinity (Xx-ray) is obtained directly from the diffractogram after subtraction of the amorphous halo. There are two general methods for this subtraction. If the completely non-crystalline material is available, a diffractogram pattern is obtained in the same angular range. In this diffractogram the ‘‘halo’’ is properly scaled and subtracted from the diffractogram of the semi-crystalline polymer. One example of this procedure is shown in Figure 2 for isotactic poly(propylene), iPP [43]. Here, hydrogenated poly (2-methyl-1,3-pentadiene) was used as a model atactic poly(propylene) since it is completely amorphous at room temperature. Once this subtraction is accomplished the mass-based degree of crystallinity is calculated as: Ic Xx-ray ¼ (1) I c þ KI a
Figure 2 X-ray diffractograms recorded at room temperature. (a) Metallocene-synthesized isotactic poly(propylene), mmmm ¼ 0.996 crystallized at 1451C. (b) Atactic poly(propylene). Reproduced with permission from Ref. [43]. Copyright John Wiley & Sons, Inc., 1999.
259
Phase Structure and Morphology
Ic is the sum of the area of all crystalline reflections corrected for Lorentz, polarization and thermal effects, and Ia the area of the amorphous halo. K is a proportionality constant to account for the relative scattering efficiencies of the amorphous and crystalline material. For many systems K is usually close to 1 [44–50]. The actual corrections to each of the observed crystalline reflections are complex and the factors involved depend on the diffractographic plane. Detailed analyses for iPP were carried out by Natta [51] and Mo and Zhang [52] who obtained K values of 2.03 and 1.25, respectively. In a slightly different approach Weidinger and Hermans [53] studied diffractograms of iPPs with different but unknown, crystallinity levels. After subtraction of the halo, the Ic vs. Ia plot displayed a linear regression that yielded limiting values at Ia ¼ 0 (100% crystalline, I oc ) and Ic ¼ 0 (100% amorphous, I oa ). With those limiting values, the level of crystallinity follows directly from I c ¼ Xx-ray I oc I a ¼ ð1 Xx-ray ÞI oa
ð2Þ
These methods, and the most simple one with K ¼ 1, were comparatively analyzed in a series of iPPs with crystallinity levels ranging from B0.50 to B0.80. The results are shown in Table 1. For this system, the corrections proposed by Natta and the most simple subtraction method (K ¼ 1) gave similar results. The values obtained by the Hermans–Weidinger method are only slightly lower; however, the method developed by Mo and Zhang yield consistently higher values. From this comparison, it appears that the most used simple method with K ¼ 1 gives reasonable crystallinity values. When the diffractogram of the pure amorphous polymer is not available at room temperature, the shape of the halo can be deduced either by peak fitting or estimating the halo pattern from the corresponding shape of the molten material. The uncertainties associated with these methodologies arise from the need to give a Table 1 Comparison of degree of crystallinity for metallocene isotactic poly(propylenes) from wide-angle X-ray scattering analyzed by different methods Mwa
Crystallization mode
Xx-ray (1)
Xx-ray (2)
Xx-ray (3)
Xx-ray (4)
102,500 182,000 200,500 327,000 403,500 439,000 349,500 346,500 335,500
Tc ¼ 1551C (7 days) Tc ¼ 1551C (7 days) Tc ¼ 1551C (7 days) Tc ¼ 1551C (7 days) Tc ¼ 1551C (7 days) Tc ¼ 1551C (7 days) Quenched to 01C Quenched to 01C Quenched to 01C
0.74 0.71 0.74 0.69 0.74 0.73 0.62 0.57 0.54
0.82 0.80 0.82 0.78 0.82 0.81 0.73 0.68 0.65
0.72 0.68 0.72 0.68 0.72 0.68 0.58 0.53 0.48
0.77 0.74 0.78 0.74 0.77 0.74 0.64 0.59 0.54
Notes: (1), Method of Natta et al. [51]; (2), method of Mo and Zhang [52]; (3), method of Hermans and Weidinger [53] and (4), from Isasi et al. [43]. a iPP, Mw/Mn ¼ 2.270.2
260
Rufina G. Alamo
Intensity
(110)
(200)
10
15
20
25
30
2θ
Figure 3 Non-linear least-squares curve fitting of the orthorhombic WAXS profile of an ethylene 1-decene random copolymer with 2.7 mol% branches. The two crystalline reflections and the amorphous halo are shown.
functionality (Gaussian, Lorentzian, Voigt or mixtures) to each of the crystalline and non-crystalline peaks. Curve-fitting procedures are based on minimization of the difference between experimental and calculated spectra using a non-linear leastsquares method [54]. Figure 3 is an example of the fitting procedure to two crystalline reflections and the amorphous halo for a random ethylene/a-olefin copolymer. A relative crystallinity or ‘‘crystallinity index’’ has been used as an approximate method [55,56]. The simplest procedure involves determination of the intensity at a single scattering angle (2y), in reference to the value for the amorphous halo at the same angular reflection. This method, for example, was useful to follow the variation of crystallinity of an iPP during isothermal melting [57]. The need to construct a more or less arbitrary baseline in the methods described above is a potential source of error in the determination of crystallinity by X-ray [58]. This error is minimized in a treatment by Ruland that analyzes data in a wide range of scattering angles and accounts for the natural diffuse scattering of crystalline polymers [59,60]. Theoretically, this is the most accurate method because the integration expands over a very wide angular range. Modifications and further improvements [61,62] to the original laborious method permit a similar accuracy from experimental data collected in a narrower angular range.
1.1.3 Density Volume and mass-based expressions for the degree of crystallinity are easily derived from the experimentally measured density (r) of a semi-crystalline polymer. The method is based on an ideal crystalline and liquid-like two-phase model and assumes additivity of the volume corresponding to each phase
Phase Structure and Morphology
261
(Vc, crystalline; Va, amorphous). The densities of the pure crystalline (rc) and pure amorphous (ra) polymer must be known at the temperature and pressure used to measure r. The value of rc can be obtained from the unit cell dimensions when the crystal structure is known. The value of ra can be obtained directly for polymers that can be quenched without crystallization, poly(ethylene terephthalate) is one example. However, for most semi-crystalline polymers the value of ra is extrapolated from the variation of the specific volume of the melt with temperature [16,63]. From the mass balance, rV ¼ rcVc + raVa, and volume additivity, Va ¼ VVc, the volume and mass fraction crystallinities are written, respectively. r ra rc r ra and XrðmÞ ¼ XrðvÞ ¼ (3) rc ra r rc ra The experimental determination of density can be carried out by picnometry, density gradient column or by dilatometry.
1.1.4 Thermal analysis The enthalpic change from the solid to the liquid-like phase of a semi-crystalline polymer can be obtained from DSC [16]. The mass-based degree of crystallinity (XDSC) is calculated as the ratio of the heat of fusion of the sample (DH) and the value per mole of purely crystalline polymer (DHc). XDSC ¼
DH DH c
(4)
This is a relatively fast and popular method that requires only a few milligrams of sample. DH is obtained from a measurement of the area under the melting peak obtained at a constant heating rate, in reference to the heat flow value of a standard. Although Equation (4) is conceptually correct, the application to experimental data should be undertaken cautiously, especially when an arbitrary baseline is drawn to extract the area under the DSC melting peak. The problems and inaccuracy of the calculated crystallinities associated with arbitrary baselines have been pointed out by Gray [36] and more recently by Mathot et al. [37,64–67]. The most accurate value requires one to obtain experimentally the variation of the heat capacity during melting (Cp(T)) [37]. However, heat flow (dq) values can yield accurate crystallinities if the primary heat flow data are devoid of instrumental curvature. In addition, the temperature dependence of the heat of fusion of the pure crystalline phase (DHc) and pure amorphous phase (DHa) are required. For many polymers these data can be found via their heat capacity functions (ATHAS data bank [68]). The melt is then linearly extrapolated and its temperature dependence identified with that of DHa. The general expression of the variation of Cp with temperature is dXDSC ðTÞ Cp ðTÞ ¼ XDSC ðTÞCp;c ðTÞ þ ð1 XDSC ÞCp;a ðTÞ ðDH a ðTÞ DH c ðTÞÞ dT (5)
262
Rufina G. Alamo
In this expression the major contribution to
melting is the excess heat capacity term, ðDH a ðTÞ DH c ðTÞÞ dXDSC ðTÞ=dT . For sharp melting, DHðTÞ ¼ ðDH a ðTÞ DH c ðTÞÞ is often a very small contribution, and dXDSC/dT corresponds to deviations from the linear regions of the thermogram prior and after the transition. Given that most polymers melt at temperatures well below the equilibrium value, the temperature dependence of DHc must be taken into account. These corrections could make an important contribution to the value of the crystallinity, especially for polymers with low degrees of crystallinity that melt at temperatures much lower than the equilibrium melting. In one example, the crystallinities of polyethylenes and random ethylene 1-octene copolymers calculated by the Cp measurement method were 15–50% larger than the values obtained by the standard determination of peak area [69]. Moreover, in a study with iPPs negligible differences were found for crystallinities calculated by the two DSC methods when the temperature correction of DHc is applied [70]. For these poly(propylenes) the experimental melting had relatively flat baselines. Thus, the common area determination and application of Equation (2) from flat DCS melting baselines is a good approximation for determination of crystallinity, provided the temperature correction to DHc is applied. The approximation to the temperature dependence of the heat of fusion is given by the factor: f ¼ 2T=ðT þ T m Þ, which is applicable for some polymers [71]. In this expression T is the observed melting temperature and Tm the equilibrium value defined as the melting temperature of an infinitely thick crystal. It has also been inferred that differences found between crystallinities measured by density and those from heat of fusion by DSC area determination, as given for polyethylenes in the example of Figure 4 [72], may be related to baseline uncertainties, or not accounting for the temperature correction of DHc. Given that similar differences in crystallinity from density and heat of fusion were reported for isotactic poly(propylene) [43] and poly(aryl ether ether ketone ketone), PEEKK [73], other features of phase structure that deviate from the twophase model may be involved in the crystallinity discrepancy.
1.1.5 Raman and infrared spectroscopy Both vibrational spectroscopies are valuable tools in the characterization of crystalline polymers. The degree of crystallinity is calculated from the ratio of isolated vibrational modes, specific to the crystalline regions, and a mode whose intensity is not influenced by degree of crystallinity and serves as internal standard. A significant number of studies have used both types of spectroscopy for quantitative crystallinity determination in the polyethylenes [38,74–82] and other semi-crystalline polymers such as poly(ethylene terephthalate) [83–85], isotactic poly(propylene) [86,87], poly(aryl ether ether ketone) [88], poly(tetrafluoroethylene) [89,90] and bisphenol A polycarbonate [91]. In Raman spectroscopy, for example, there are three spectral regions that give structural information about the crystalline state of the polyethylenes. The internal modes, which give quantitative information with respect to the elements of phase structures, are in the region of approximately 900–1,500 cm–1 [38,74,75]. The longitudinal acoustic mode (LAM), which gives the ordered sequence length distribution, lies in the range of about 5–50 cm–1 [92–99]. The disordered LAM
Phase Structure and Morphology
263
0.6 0.5
XDSC
0.4 0.3 0.2 0.1 0 0
0.1
0.2
0.3
0.4
0.5
0.6
Xρ
Figure 4 Plot of degree of crystallinity (XDSC) from DSC against crystallinity (Xr) determined by density measurements. (D), hydrogenated polybutadienes; (’), ethylene 1-butene copolymers; (&), ethylene 1-octene copolymers. Reprinted with permission from Ref. [72]. Copyright 1984 American Chemical Society.
(DLAM) is in the region of 200 cm–1 and gives a measure of the long-range conformational disorder [100–103]. Analysis of the Raman internal modes to yield quantitative data of the phase structure of the polyethylenes was originated by Strobl and Hagedorn [38]. They used the intensity of the CH2 bending band at 1,416 cm–1 as characteristic of the pure orthorhombic crystalline region, as this is the component of this vibration that is split by the orthorhombic crystal field. The total integrated intensity of the twisting region, 1,250–1,350 cm–1 (IT), is independent of the degree of crystallinity, thus, serves as an integral intensity standard. For a completely crystalline specimen, the ratio of intensities, I1,416/IT ¼ 0.46. Accordingly, the mass-based degree of crystallinity (ac) is calculated as: I 1;416 ac ¼ (6) 0:46 I T The content of liquid-like region (aa) is obtained by deconvoluting the intensity in the twisting region into a narrow band centered at 1,295 cm–1 and a melt-like broader component centered at 1,303 cm–1. Thus, I 1;303 aa ¼ (7) IT In addition, the amorphous (liquid-like) content can be determined from the skeletal stretching region by the relation aa ¼
I 1;080 0:79 I T
(8)
264
Rufina G. Alamo
Intensity
The factor 0.79 was found using the spectrum of the molten polymer. Further work on different types of polyethylenes found 0.43 for the factor in Equation (6), and complex band profiles in the 1,080 cm–1 region of the melt structure [104]. For a large amount of experimental data, ac+aa 6¼ 1; the difference has been attributed to the region with intermediate order, the interphase (ab) [38,72,74,75,77–80,105]. The Raman spectrum over this region of an ethylene-lhexene copolymer given in Figure 5 illustrates the deconvolution by curve fitting of regions of interest to extract quantitative data of phase structure. The agreement between the degree of crystallinity obtained by Raman and the value from heat of fusion for a large number of polyethylenes covering a wide range of crystallinities is excellent for crystallinities WB60% as shown in Figure 6. The data for lower crystallinities correspond to branched polyethylenes and ethylene copolymers for which ac is 5–10% lower than XDSC. Corrections for the temperature dependence of DHc, not done in the x-axis of this figure, will increase XDSC and make the difference slightly larger. The difference is attributed to the broad melting range of the structurally irregular chains and the need to start the DSC run at sub-ambient temperature to maximize the linearity of the baseline. Hence, XDSC includes the contribution of a small amount of crystallinity that has already disappeared at room temperature. Because ac is measured at ambient temperature, this contribution is absent in the determination of ac. Conversely, very good agreement was found between the crystallinities measured by Raman (ac+ab) and those obtained from density [106]. IR spectra can also be very useful in determining the degree of crystallinity when pure crystalline and pure liquid-like absorptions can be identified. The method follows the Lambert–Beer law that correlates the absorbance of ordered
1000
1100
1200
1300
1400
1500
1600
Wavenumber (Δυ) cm-1
Figure 5 Raman spectra of orthorhombic ethylene 1-hexene copolymer with band fitting. The crystalline band at 1,416 cm1, and amorphous bands at 1,303 cm1 and 1,080 cm1 are used to compute the crystallinity content: ac ¼ 0.52, and the amorphous content: aa ¼ 0.42. (See Color Plate Section at the end of this book.)
Phase Structure and Morphology
265
Figure 6 Plot of the degree of crystallinity from Raman (ac) against crystallinity from heat of fusion (XDSC) for linear and branched (————) polyethylenes and for ethylene copolymers. Reproduced from Polymer Journal with permission from Ref. [106]. Copyright 1985, The Society Polymer Science, Japan.
entities (A) with the extinction coefficient Kc of these regions, the density r and thickness (d) of the specimen. A ¼ Kc Xir r d
(9)
This technique has been successfully applied to linear polyethylene (PE). For example, in this polymer of the three rocking mode bands in the 725 cm–1 region, two sharp bands near 730 and 722 cm–1 are associated with the crystalline fraction, and a third broad component, overlapping the 722 cm–1 band, represents the amorphous component [107–110]. The broad liquid-like band was identified in the spectra of molten linear PE and n-alkanes in which the 730/722 cm1 doublet is replaced by a broad band centered near 723 cm1 [107]. From the overlapping spectral region, crystalline and amorphous bands are deconvoluted by standard curve-fitting methods. A second useful region for crystallinity determination of PE is the methylene scissoring modes in the 1,420–1,475 cm1 region. Again, two of these bands 1,473 cm1 and 1,463 cm1 appear from the splitting of this mode by the crystal field; they are thus crystalline bands, the third at 1,487 cm1 is broader and is associated with the amorphous regions [107]. The ratio of the crystalline band at 1,894 cm1 to the internal standard 1,303 cm1, corrected by their corresponding extinction coefficients, has also been used for crystallinity measurement. Using IR methods the degree of crystallinity of polyethylene was identical to the calculated by density [110], and the same as that
266
Rufina G. Alamo
from heat of fusion [107] and from WAXS [111], indicating a good correspondence between the three methods. In addition to quantitative crystallinity data, IR and Raman have been proven valuable tools to extract information on chain conformation in the three major phases [112–114], local order in amorphous polymers [115,116] high throughput characterization [117] and structural and polymorphic changes on heating and cooling semi-crystalline polymers [118–120].
1.1.6 NMR spectroscopy Both 1H and 13C solid-state nuclear magnetic (NMR) spectroscopy have been used to determine the degree of crystallinity in polyethylenes [121–129]. Fully relaxed 13C NMR spectra, obtained under high-power dipolar-dicoupling and magic angle spinning, display distinct resonances for the disordered amorphous carbons (B31 ppm) and those associated with the ordered orthorhombic crystalline regions (32.8 ppm) [124]. The intensity of each region is obtained by peak deconvolution. The example of Figure 7 gives evidence for good agreement between crystallinities obtained from 13C NMR and WAXS-determined crystallinities in the same polyethylenes [129]. In recent work spin diffusion [130], as well as a sequence that combines a spin diffusion filter prior to cross-polarization, were applied to quantify the phase content of polyethylenes and styrene-isoprene block copolymers [131]. Further detailed NMR studies of the relaxation properties of the crystalline regions have identified a heterogeneous behavior with respect to motions in the megahertz frequency range, those responsible for the spin-lattice relaxation [126]. The T1C relaxation of the crystalline phase obtained via inversion recovery with cross-polarization cannot be fitted to a single exponential function. It requires two or three components that are associated with regions of different structural order [132]. Two orthorhombic 100
XNMR
90 80 70 60 50 50
60
70
80
90
100
Xx-ray
Figure 7 Plot of the degree of crystallinity (XNMR) by obtained by 13C NMR against crystallinity (XX-ray) obtained by wide angle X-ray diffraction for an unfractionated linear polyethylene sample crystallized in different conditions (data from Ref. [129]).
Phase Structure and Morphology
267
crystalline components with distinctly different dynamics were detected in a series of different types of polyethylenes using different solid-state NMR pulse sequences [133]. NMR cannot distinguish whether the more mobile region is localized close to the boundary with the liquid-like region or randomly dispersed within the more rigid all-trans component. Nonetheless, the former could be taken as the more plausible scenario because the presence of a diffuse region where the order is dissipated is expected in the semi-crystalline structure [126,128].
1.2 Characterization of the liquid-like phase While characterization of the type of crystallographic symmetry in the crystalline regions is straightforward from the WAXD patterns of oriented specimens, the characterization of the configurational properties of the polymer chains connecting crystallites in the interlamellar region has been elusive. Predictions of the state of order and topological details have been based on comparative studies with the molten system [134–138] or by theoretical simulations [139–143]. Concerning linear polyethylene, inelastic neutron scattering (INS) gave evidence by direct experimentation that the molecular conformation of the chains in the interlamellar regions of solid samples had the same random coil dimensions as those in the melt [144]. The experiments confirmed the prevailing view that, upon solidification of flexible chains, the random conformation was preserved in the amorphous (liquid-like) region. Hence, once accounts are made for the interfacial region where the chain-order emerging from the crystal is dissipated, the dimensions of the chain in the remainder interlamellar region have the characteristics of random coil in the melt. Spectroscopic methods have been most useful to infer properties of the liquidlike region. For example, the DLAM of the Raman spectra of polyethylenes gives information about the degree of conformational disorder of polyethylenes [102,103]. The frequency of the DLAM band depends on the ratio of the number of trans to gauche bonds and the chain length. For the linear chains this band in solid samples had the same similarities as for the pure melt. Examples are illustrated in Figure 8. The spectra shown are for a high molecular weight linear polyethylene with a room temperature crystallinity level of 0.42. The corresponding spectrum of the melt of the same polymer is shown in Figure 8(d); it is characterized by a broad band at B200 cm1. This band is also present in the room temperature spectrum of the solid sample, Figure 8(a). As the temperature is initially increased, the intensity of this band increases slightly while the frequency remains constant. In the molten state, 1471C, the DLAM becomes more intense but the frequency is unchanged. This result indicates that the amorphous region of the bulk crystallized linear chain has the same random conformation as that of the molten sample, in analogy to the neutron scattering results. The DLAM frequency of random copolymers of ethylene behaves in a different manner [103]. For these copolymers ethyl and longer branches are excluded from the crystal region. The branches accumulate in the interlamellar
268
Rufina G. Alamo
Figure 8 Plot of low frequency Raman spectra of a high molecular weight linear polyethylene that was initially quenched at 701C as a function of temperature. Spectra obtained at (a) room temperature, (b) 571C, (c) 871C and (d) 1471C. Reprinted with permission from Ref. [102]. Copyright 1986 American Chemical Society.
region increasing the number of gauche bands in this region [72,80]. This effect translates into an increase of the Raman DLAM band with increasing branching content, and parallels the measured and calculated decrease of the characteristic ratio of model copolymers with increasing branching content [145,146]. Changes by the accumulation of branches in the interlamellar region were also followed by analysis of the angular position of the amorphous halo (2yhalo) [54]. For the same crystallographic phase, the peak of the halo correlates with short-range
Phase Structure and Morphology
269
Decene(q)
20
2 Theta (Halo)
Linear PE Decene(an)
19.8
19.6
19.4
19.2 0
5
10
15
20
Comonomer Content (Mol%)
Figure 9 Room temperature variation of peak 2yhalo for ethylene 1-decene copolymers quenched (q) and annealed at room temperature (an). The value for the linear polymer is also given.
intermolecular van der Waals interactions and with the characteristics of the radial coil. As shown in Figure 9 for a series of quenched, and annealed ethylene l-decene copolymers, the 2yhalo decreases linearly with increasing comonomer reflecting the increase of the average backbone carbon–carbon intermolecular distance in the amorphous region. Bulkier branches expand the coil further; as a consequence, the 2yhalo is shifted to lower values [54]. The conformational properties of the liquid-like and glassy states of polyethylene terephthalate (PET) have been amply studied by vibrational spectroscopy [147,148], and solid-state NMR [149]. The issue of concern is the degree of trans/gauche isomerization that the chain undergoes from the equilibrium population in the liquid-like state to either (i) the semi-crystalline state or (ii) the glassy state. It has been found that while the crystalline regions adopt the all-trans conformations, the preferentially gauche, unperturbed random conformational statistics and chain dimensions of the melt are preserved in amorphous and glassy PET, in agreement with Flory’s predictions [149]. In more recent studies, attempts have been made to extract the structure of the amorphous regions using position annihilation lifetime spectroscopy (PALS). The temporal changes of positrons trapped in a material due to interactions with host electron are followed in this spectroscopy [150,151]. Positrons annihilate either as free positrons or from a bound state with a host electron, termed positronium (Ps), an analogue of the hydrogen atom [152]. The Ps can exist either in a singlet spin (parapositronium, pPs) or a triplet spin (orthopositronium, oPs) state. While self-annihilation of pPs is a fast allowed process, annihilation of oPs proceeds via reaction with an electron of the host, such that the value of the lifetime (t3) and the intensity (I3) of oPs are sensitive to the state of order, and free volume of the polymeric matrix where oPs annihilates. Changes in free volume in the interlamellar region of semi-crystalline polymers are resolved by this technique.
270
Rufina G. Alamo
The PALS technique has been used to determine the contents of amorphous and interfacial regions of linear polyethylenes with different crystallinities [153,154] and of ethylene- and propylene-based random copolymers [155–159]. The results for a series of ethylene l-octene random copolymers with increasing mol% comonomer are given in Figure 10 [158]. Here the content of crystals was obtained from WAXS. In the calculation the authors assumed that all noncrystalline regions of linear polyethylene were in a rigid amorphous state, while those of the copolymers were a mixture of mobile and rigid amorphous. For the ethylene 1-octene copolymers studied, the interfacial regions calculated from PALS are significantly larger than the values obtained from the Raman internal modes analysis [72,74]. The use of 13C NMR is another effective probe with which to investigate the non-crystalline region of semi-crystalline polymers. Solid-state 13C NMR spectra display resonances that can be assigned to carbons in the crystalline and noncrystalline environments, thus confirming the coexistence of both regions [124,125,160]. The 13C NMR spin-lattice relaxation times (T1c) of the two regions usually differ by over two orders of magnitude [161,162]. Thus, by adopting appropriate pulsing programs, it is possible to separate the amount of carbons associated to each relaxation. In particular, it is possible in favorable situations to compare T1c of the non-crystalline region of semi-crystalline polymers with that of the pure melt. In one example, the T1cs of the non-crystalline methyl, methine and methylene carbons of iPP, 70% crystalline, were compared at room temperature with those of model atactic poly(propylene), hydrogenated poly(2-methyl-1,3pentadiene) [163]. It was found that, within the experimental error, the T1c values of each of the carbons were the same in both polymers. The conclusion can then be reached that the fast segmental motion, at or near the Larmor frequency of
Figure 10 Degree of crystallinity from WAXS, interfacial content from PALS and amorphous content from PALS for an ethylene 1-octene copolymers as a function of increasing 1-octene. Reproduced with permission from Ref. [158]. Copyright 2002 Elsevier Ltd.
Phase Structure and Morphology
271
5–500 MHz, which determine the T1cs, are the same for the non-crystalline region of isotactic poly(propylene) and for atactic poly(propylene). This in turn indicates that the disordered chain structure is the same for the two cases. A similar comparison can be made with cis-poly(isoprene), natural rubber, by taking advantage of the fact that the polymer is very slow to crystallize [164]. Consequently, the comparison can be made between the supercooled, noncrystalline polymers at 01C and the semi-crystalline polymer (31% crystalline) at the same temperature. The T1c values for each of the five carbons involved were again found to be the same for the completely disordered polymer and the semicrystalline one, so that a similar conclusion can be made with regard to their chain structure. An analogous comparison cannot be made with linear polyethylene since this polymer crystallizes very rapidly. However, by varying the molecular weight and crystallization temperature, a crystallinity range from 0.57 to 0.90 can be obtained at room temperature [165]. The T1 values for such samples are essentially constant with deviations being only about 75% from the average value. The effective correlation time was calculated to be the same as that of the interior chain carbons of pure molten n-alkanes. Thus, the fast internal segmental motions, which determine T1, are the same in the non-crystalline regions of linear polyethylene and the melts of the low molecular weight n-alkanes. Moreover, the major differences in morphological forms that can be developed influence this type of motion [165,166]. For both linear and branched polyethylene T1c is a continuous, monotonic increasing function over a temperature range that encompasses both the crystalline and completely molten polymers. Poly(ethylene oxide) and poly(trimethylene oxide) behave in a very similar manner [166]. The aforementioned results for several different polymers clearly demonstrate that the rapid segmental motions as reflected in the T1 measurements are the same for the non-crystallization region and the completely molten polymer.
1.3 Characterization of the interphase The interfacial zone is by definition the region between the crystallite basal surface and the beginning of isotropy. Due to the conformationally diffuse nature of this region, quantitative contents of the interphase are most often determined by indirect measures. For example, they have been computed as a balance from one of the sum of the fractional contents of pure crystalline and amorphous regions. The analysis of the internal modes region of the Raman spectrum of polyethylene, as detailed in the previous section of this chapter, was used to quantify the content of the interphase region (ab). A factor analysis of the Raman spectra of a set of linear polyethylenes identified the existence of a third component in addition to the pure crystalline and pure amorphous components [78]. The characteristics of the Raman spectrum of the interphase were very similar to that of the crystalline spectrum indicating that the interphase retains a significant degree of order. Using the Raman method, the content of interphase in linear polyethylenes was found to increase with molecular weight [74–76,78]. For molecular weights below
272
Rufina G. Alamo
B20,000 g/mol, ab is only about 5% and increases to 15–20% for the higher molecular weights. Unfractionated ultra high molecular weight reactor powders display even higher contents of interphase [77]. The increase of interphase with comonomer content in random ethylene copolymers [72,79,80,167] is correlated with the accumulation of topographical defects, entanglements, structural irregularities and comonomer preferentially at the interphase. Analogous to the factor analysis results in linear polyethylene, a structural study of bisphenol A polycarbonate by Raman spectroscopy, WAXS and DSC concluded that the interfacial region was partially ordered [91]. Heat capacity measurements at the glass transition temperature, Tg, are based on the same differential concept. The weight fraction of amorphous phase is calculated as the ratio of changes of heat capacity of the semi-crystalline sample DCp(s) over the change in heat capacity of the melt (DCp(m)) at the glass transition. For a two-phase system, the degree of crystallinity is given as: Xcp ¼ 1
DCpðsÞ DCpðmÞ
(10)
However, it has been found for many systems that Xcp þ DCpðsÞ =DCpðmÞ a1, and the semi-crystalline structure is better described by a three-phase model. The region of intermediate order was initially defined as an inter-crystalline phase [168,169]. Further, detailed studies identified the portion of non-crystalline polymer that does not contribute to the heat capacity at Tg as the ‘‘rigid amorphous phase’’ [170]. This portion is structurally assigned to the region between crystalline and amorphous phase, or to the interphase [171–174]. The determination of the rigid amorphous fraction requires a precise knowledge of Tg and of the degree of crystallinity at Tg preferably by a method other than the thermodynamic one. In spite of the long empirical extrapolation of DCp from the melt to Tg, the contents of interfacial region obtained by this method are similar to values obtained by vibrational spectroscopies [175]. A combination of DSC, NMR, WAXD and small-angle X-ray scattering (SAXS) analysis of the phase structure of aliphatic poly(amides) concluded that about 20% of the mass was in a rigid amorphous conformation inside the crystals [176]. Dielectric relaxation [171,177–180] and solid-state NMR spectroscopy [121–123,181–185] have been used extensively to isolate and quantify the structural region of intermediate order. In NMR spectroscopy, resonance spectra are interpreted as pertaining to nuclei in three different conformational environments. The most extensive work has been carried out analyzing proton broad-line and 13C DD-MAS (dipolar decoupling magic angle spinning) NMR spectra of polyethylenes. 1H spectra were deconvoluted into a broad (immobile) component characteristic of the crystalline regions, a narrow component associated with short-range motions (mobile) in the liquid-like regions, and an intermediate component corresponding to the interfacial region of intermediate mobility [121–123,181–185]. A detailed analysis by spin diffusion concluded that the interfacial region of linear polyethylenes is more dense than the amorphous ˚ thickness [183]. In a study of linear polyethylenes, as the and averages B50 A molecular weight increased from 13,000 g/mol to 3,400,000 g/mol the content of
Phase Structure and Morphology
273
interface calculated from deconvolution of the broad-line 1H NMR spectra, increased from 6% to B18%. Concomitantly, the crystalline content decreases from 94% to 64% and the amorphous content increases from 0.2% to B19% as molecular weight increases [123]. The changes reflect the increase of entanglements per chain as molecular weight increases. Similarly, 1H spin-lattice relaxation processes are described in terms of three components with different T1 values [186]. High-power dipolar decoupled 13C NMR spectra under magic angle spinning have also been analyzed in reference to three-phase systems. The DD-MAS 13C NMR spectrum of linear polyethylene displays two distinct resonances associated with carbons in crystalline (32.8 ppm) and non-crystalline (31 ppm) environments [124]. The spin–spin relaxations (T2c) of the carbons in the noncrystalline regions display two components. One with T2c ¼ 2.4 ms is associated with highly mobile carbons of the liquid-like region. The second component with T2c ¼ 44 ms can be assigned to carbons with more restricted motion in the interface. On this basis, the 13C NMR spectrum was resolved into three components using pure Lorentzian-shaped peaks. The content of each component is obtained from peak fitting of the experimental spectra using non-linear regression. Interfacial contents obtained in different polymers using this method are listed in Table 2 [187–192]. Clearly, the interface is a significant component (15–30%) of the phase structure of the polymers listed. In a comparative study of the crystallinity of isomeric aliphatic polyamides by NMR, DSC and X-ray, the NMR-based crystallinity was obtained by a two component fit of the proton broad-line spectra and their associated mobilities by T1r determination. Compared to the crystallinity estimates from DSC and WAXS, the content of rigid material obtained from NMR is significantly higher, but comparable to the crystallinity determined by SAXS. The difference with the DSC value was associated with a fraction of intermediate order within the crystalline phase [193]. Deuterium and 31P NMR spectra of poly(butylene terephthalate) and poly(bis (phenoxy) phosphazene) have also been analyzed on the basis of three conformational environments [194,195]. Significant interfacial contents of up to 25% were extracted from this analysis. In a more qualitative manner, an Table 2
Interfacial content determined by DD MAS 13C NMR
Polymer
Linear polyethylene M ¼ 2.5 105 (fraction) M ¼ 3.0 106 (unfractionated) M ¼ 4.0 104 (unfractionated) M ¼ 1.85 105 (unfractionated) Isotactic-poly(propylene) Poly(e-caprolactone) Poly(tetramethylene oxide)
ab
0.16 0.18 0.16 0.20 0.30 0.30 0.22
Reference
[125] [125] [127] [290] [190] [291] [192]
274
Rufina G. Alamo
interphase was included in addition to crystalline and amorphous regions to describe the semi-crystalline structure of a large variety of polymers. Among them are analysis of NMR spectra and those associated with chain dynamics of poly(vinyl alcohol) [196], syndiotactic poly(propylene) [197], poly(ethylene naphthalene-2,6-dicarboxylate) [198], poly(aryl ether, ether ketone) [199] and poly(ethylene terephthalate) [200].
2. SUPERMOLECULAR MORPHOLOGY Although spherulites are the most common form of supermolecular structures that are observed in crystalline polymers, they are not the only morphological type of lamellar aggregates [201]. A common progression of the development of spherulites starts from an initial small bundle of lamellae that grows longitudinally and spreads and branches off transversally like a sheaf. Radial growth continues until impingement between neighboring spherulites, thereby ending as a polyhedral ‘‘grain-type’’ structure such as the examples given in Figure 11 for isotactic poly(propylene) and linear poly(ethylene). Spherulites are birefringent, hence, when viewed with polarized light in an optical microscope, black extinction regions give rise to the appearance of a Maltese cross with arms parallel and perpendicular to the direction of the retardation path. Thin-section transmission electron microscopy (TEM) has been the usual, preferred technique to characterize lamellar morphology. Contrast between amorphous and crystalline regions is obtained by acid etching or staining. The details of etching with chlorosulfonic or permanganic acid have been described in different works [202,203]. Staining with RuO4 has been described as well [204]. The acid or staining medium penetrates and accumulates preferentially in the amorphous region. Optical and electron transmission microscopy give a two dimensional view of the supermolecular morphology and lamellar structure. In contrast, scanning election microscopy (SEM) gives a three-dimensional view
Figure 11 Left: Spherulites of a Ziegler–Natta isotactic poly(propylene) with Mw ¼ 271,500 g/mol and mmmm ¼ 0.95, isothermally crystallized at 1481C. Right: Banded spherulites of a linear polyethylene with Mw ¼ 53,600 g/mol slowly cooled from the melt.
Phase Structure and Morphology
275
of the specimen surface. At high magnifications SEM can supply details of the lamellar structure [205]. Recent developments have allowed atomic force microscopic (AFM) studies to follow the course of spherulite development and the internal lamellar structures as the spherulite evolves [206–209]. The major steps in spherulite formation were followed by AFM for poly(bisphenol) A octane ether [210,211] and more recently, as seen in the example of Figure 12 for a propylene l-hexene copolymer [212] with B20 mol% comonomer. Accommodation of significant content of l-hexene in the lattice allows formation and propagation of sheaf-like lamellar structure in this copolymer. The onset of sheave formation is clearly discerned in the micrographs of Figure 12 after crystallization for B10 h. Branching and development of the sheave are shown at later times. The direct observation of sheave and spherulitic formation by AFM supports the major features that have been deduced from transmission electron and optical microscopy. The fibrous internal spherulite structure could be directly observed by AFM. Polymer spherulites may display extinction patterns more complex than the Maltese cross [213]. A pattern also commonly observed is concentric rings that have regular periodicity, as illustrated in the example of Figure 11 for ring spherulites of polyethylene [214]. Alternating dark and white bands result from a periodic change of orientation of the birefringent entities along the spherulite radius. Electron microscopic studies of replica of fracture surfaces of meltcrystallized polyethylene, containing spherulites with periodic extinction rings, show thin lamellae that change their orientation periodically along the radius of the spherulite. The period is identical with that of the extinction rings observed under the polarizing microscope [215]. Both molecular weight and crystallization temperature can alter the resulting supermolecular patterns. The influence of crystallization temperature has been studied for fractions of poly(ethylene adipate) [216], poly(trimethylene terephthalate) [217], polyethylene oxide [218], poly 1,3-dioxolane [219] and linear polyethylene fractions [220] among others. In some systems the morphological change correlated with a change of growth regime [216,219–221]. The patterns observed as a function of crystallization temperature for poly(ethylene adipate) are shown in Figure 13. Typically, axialites form at high crystallization temperature (Figure 13(A)), banded spherulites are found as the crystallization temperature is lowered. At relatively low crystallization temperatures the spherulites are no longer banded, though a well-defined Maltese cross remains. Studies of the effect of molecular weight on spherulite formation in linear polyethylene fractions indicate that structures with a high order of spherical symmetry develop only in a range of chain lengths [222,223]. The studies combined optical microscopy and small-angle laser light scattering (SALLS) to characterize morphological patterns by the lamellar degree of organization. Five most typical Hv patterns, where the incident light is polarized vertically and the scattered light is polarized horizontally, are given in Figure 14 [224]. Patterns (a), (b) and (c) represent spherulitic structures with order deteriorating from (a) to (c). Pattern (d) is indicative of lamellae organized as rod-like aggregates. Pattern (e), which displays no angular dependence of the scattering, can be
276
Rufina G. Alamo
Figure 12 AFM images of development of axialites from the initial stages at room temperature for a random propylene 1-hexene with 25.1 mol% 1-hexene. The time is indicated. Reprinted with permission from Ref. [212]. Copyright 2005 American Chemical Society.
Phase Structure and Morphology
Figure 13 Top, plot of linear growth rates of poly(ethylene adipate) spherulites as a function of crystallization temperature for indicated molecular weight fractions. Spherulites shown correspond to the indicated range of temperatures. (A) Crystallization at the lower temperature range; (B) at intermediate temperatures; (C) crystallization at high temperatures. Reproduced with permission from Ref. [216]. Copyright 1956, John Wiley & Sons, Inc.
277
278
Rufina G. Alamo
Figure 14 Most characteristic small-angle laser light scattering patterns (Hv) observed with linear polyethylene fractions. Reproduced by permission of The Royal Society of Chemistry from Ref. [224].
attributed to rods whose breadth is comparable to their length (sheet-like structure) or randomly oriented lamellae. Optical microscopy can be used to distinguish sheet-like morphology (g) (plotted in Figure 15) from a collection of random lamellae (h) [222,224]. Controlling crystallization conditions, a morphological map was constructed that delineates the polyethylene molecular weight and crystallization temperature regions where structures of different types are formed. Such a morphological map is given in Figure 15. Clearly spherulite formation is not a universal mode of polymer crystallization, as confirmed in other studies [225,226]. In the region where spherulites are formed, the order decreases with increasing molecular weight. Rod structures (d) are formed at the lowest molecular weights and randomly oriented lamellae at high molecular weights (W1.6 105 g/mol). As the crystallization, or quenching temperatures increases, in the spherulite forming molecular weight range, there is a demarcation temperature above which rodlike scattering patterns Figure 14(d) are observed. If one takes well-organized spherulite (a) types as reference points, then the organized structures gradually deteriorate with increasing molecular weight and cooling rate. Except for the highest chain length, it is possible for a fixed molecular weight to develop different supermolecular structures by varying either the quenching or the isothermal crystallization temperature. As has previously been described, banded type spherulites form in the central region of the map [214]. Further studies in mixtures of polyethylenes of different chain lengths show that
279
Phase Structure and Morphology
107
106 h
105
M
c
104
b
o 103
130
g Tc
d 102 -150
-100
-50
0
50
100
115
TEMPERATURE OF QUENCHING AGENT (°C) NON − ISOTHERMAL
Figure 15 Morphological map of linear polyethylene fractions. Plot of molecular weight against crystallization temperature. The types of supermolecular structures are represented by symbols. Patterns a, b and c represent spherulitic structures with deteriorating order from a to c. Patterns g and d represent rods or sheet-like structures whose breadth is comparable to their length g or display a different aspect ratio d. Pattern h represents randomly oriented lamellae. Neither h nor g patterns have azimuthal dependence of the scattering. Reproduced with permission from Ref. [223]. Copyright 1981 American Chemical Society. (See Ref. [223] for full details.) Note: the pattern ‘a’ is actually located as ‘o’ in the figure; this was an error on the original.
irrespective of the superstructures of the pure species, the morphological result for the blend corresponds to the pattern of the blend’s number average molecular weight [227]. Morphological maps for long-chain branched polyethylenes and random ethylene copolymers demarcating the formation of spherulites of different orders have been also constructed [228,229]. Thin-section electron microscopic studies of fractions of linear polyetheylene have shown systematic changes in the details of the lamellar crystallites that correlate quite well with the supermolecular structure as characterized by SALLS [222,230,231]. The change of lamellar patterns with increasing molecular weight vary in parallel with the observed supermolecular morphology as shown by the TEM micrographs of linear polyethylene fractions given in Figure 16. The staining reagent does not penetrate the crystalline regions, which appear as light
280
Rufina G. Alamo
Figure 16 Typical electron micrographs of quenched samples of indicated molecular weight fractions of linear polyethylene. Reproduced with permission from Ref. [231]. Copyright 1984, John Wiley & Sons, Inc.
regions in the micrographs. Dark areas correspond to non-crystalline regions. For low and modest molecular weights, the lamellae are straight and long and lead to well-organized stacked lamellae that correlate with the rod-like SALLS patterns. As the molecular weight increases, the lamellae become curved and shorter due to restrictions imposed by the higher entanglement density per chain, resulting in spherulitic structures continuously deteriorating. At high molecular weights the crystallites become highly segmented and arrange randomly. The crystalline morphology of poly(propylenes) is of interest due to the role of defect microstructure and crystallization temperature affecting the type of unit cell that develops and the homoepitaxial lamellar branching. The lamellar and crystallographic habits of the monoclinic (a) and orthorhombic (g) phases of poly(propylene) are unique among flexible chain molecules. For the a phase at the resolution level of the electron microscope, a three-dimensional array of nearly orthogonal ‘‘cross-hatched’’ lamellae is usually found [232–234]. The details of the molecular arrangement of the branching have been explained in terms of a homoepitaxial crystallization of transverse lamellae on the lateral 010 face of the parent ones [232–237]. This is possible by the near equivalence of the a and c axes of the unit cell and a good interdigitation of the methyl groups. The development of lamellar branching in homo poly(propylenes) is affected by
Phase Structure and Morphology
281
isotacticity, undercooling and degree of transformation, and the impact on optical properties has been recently summarized by Lotz [238]. Positive, negative or mixed spherulites develop depending on the relative proportion of radial and transverse lamellae and on the orientation of the radial lamellae relative to the path of light. Spherulites with a negative character develop at the highest and lower undercoolings due to a reduced frequency of branching, while most often mixed spherulites develop at intermediate undercoolings. In some favorable conditions and with prolonged crystallization time, mixed spherulites acquire positive character due to branch infilling during secondary crystallization [239]. One consequence of the epitaxial lamellar crystallization (cross-hatching) in isotactic poly(propylenes) is the observation of two endothermic peaks that are obtained by conventional DSC [240]. A representative thermogram, obtained after isothermal crystallization at 1481C is given in Figure 17 for a Ziegler–Natta catalyzed isotactic poly(propylene) [241]. In a parallel experiment, the same polypropylene was crystallized in a microscope hot stage at the same temperature. Spherulites with mixed type birefringence were obtained. Subsequently, the temperature of the hot stage was raised to 1711C, a temperature just beyond the peak of the low temperature endotherm, and changes in the spherulites were followed with time. The change from mixed to negative birefringence is consistent with preferential melting of the transverse lamellae. It is then concluded that the low temperature endotherm results from the
Tc = 148
178.4°C 168.8°C
171.0°
(a) Tc = 148C, 2days
(c) 171C, 80min
140
150
160 170 temp (°C)
180
(d) 171C, 200min
190
(b) 171C, 10min
(e) 171C, 300min
Figure 17 Isothermal melting of Ziegler–Natta isotactic poly(propylene). (a) Spherulites with mixed birefringence at Tc ¼ 1481C. The top middle figure displays the melting for the same thermal history. (b) Subsequent to crystallization, the temperature was raised to 1711C; spherulites acquire negative birefringence. (c), (d) and (e) Isothermal melting at 1711C for 80, 200 and 300 min, respectively. Reproduced with permission from W.T. Huang, Dissertation, Florida State University, 2005. (See Color Plate Section at the end of this book.)
282
Rufina G. Alamo
cooperative melting of the branched or tangential lamellae. The high temperature one corresponds to the melting of the primary or radial lamellae. Furthermore, after 300 min, the whole structure is melted, indicating that isotactic poly(propylenes) melt with significant isothermal melting kinetics. This phenomenon requires the melting of the tangential lamellae so that the fusion of the epitaxial structure is not involved. What is involved is the melting of the radial lamellae devised of the epitaxy. The rate of isothermal melting depends on the location of the annealing temperature between the two initial endotherms. The isothermal melting kinetics has also been demonstrated by time resolved in-situ WAXS studies. The higher the annealing temperature is the faster the isothermal melting [242,243]. The structure of the unit cell of the g form of isotactic poly(propylenes) is unique to polymeric systems. It represents the first, if not the only one, observed to date where the chain axes are not parallel to one another. The gamma phase comprises non-parallel chains tilted at 40o to the lamellae normal and is favored in poly(propylenes) with short continuous isotactic sequences [244,245]. Defects of the stereo type or constitutional irregularities such as the 2,1 defect, the 3,1 defect or comonomers added to the iPP chain, disrupt the length of continuous crystallizable sequences (primarily isotactic placements), and enhance the formation of the g polymorph [246]. It was initially proposed by Lotz and Bru¨ckner that the development of a and g branching are intimately correlated as shown in the schematics of Figure 18 [245–249]. The morphological predictions from this model for iPP systems that undergo a change in polymorphic content (a/g ratio) were confirmed by AFM studies of a series of propylene ethylene copolymers made by a metallocene catalyst [246]. The content of stereo and 2,1 defects is fixed at 1.170.1 mol% in this series, hence the major crystallographic and morphological differences observed are due to the effect of the ethylene counit. As shown in Figure 19(a), at a fixed crystallization temperature, the g
Figure 18 Schematic model of a iPP and g iPP branching from a parent lamellae. The crystallographic axes are indicated. Adapted from similar schemes in Refs. [245,246], with permission of Elsevier; copyright 2004.
Phase Structure and Morphology
283
PE 1.8, Tc = 110°C, ~ 40% γ
(a) 100
(b)
Gamma Content (%)
80
60
PE 3.4, Tc = 110°C, ~ 70% γ 40
PE 1.8 PE 2.8 PE 3.3 PE 3.4 PE 5.8 PE 8.7
20
0 80
90 100 110 120 130 Crystallization Temperature (°C)
140
PE 8.7, Tc = 110°C, ~ 100% γ
Figure 19 (a) Percentage of g phase vs. crystallization temperature,Tc, for metallocene propylene ethylene copolymers with ethylene content increasing from 0.8 to 7.5 mol%. (b) AFM phase images of selected copolymers with different content of g phase. The arrows indicate the radial direction of the spherulite. Reprinted from Ref. [246] with permission from Elsevier; copyright 2004.
content increases with increasing defects. The morphology for samples crystallized at 1101C, shown in Figure 19(b), reflects structural changes that parallel the schematic model for a/g branching. At this temperature the content of g phase changes from B40% (PE1.8) to B100% for PE8.7. Consequently, with increasing g content, iPP a lamellae that grow in the direction of the spherulite radius and branches thereon, are replaced in g rich copolymers with a dense array of short lamellae transverse or tilted to the main structural growth axis [246,250–254]. The images give evidence of systematic changes in the crystalline texture of random propylene copolymers with increasing comonomer content and crystallization temperature. The changes follow the variation in polymorphic content and the proposed growth models for epitaxial branching.
284
Rufina G. Alamo
2.1 Lamellar thickness The thickness of the ordered crystalline regions, termed crystallite or lamellar thickness (Lc), is an important parameter for correlations with thermodynamic and physical properties. Lc and the distribution of lamellar thicknesses can be determined by different experimental methods, including thin-section TEM mentioned earlier, atomic force microscopy, small-angle X-ray scattering and analysis of the LAM in Raman spectroscopy. Precise thickness measurements by TEM require sections transverse to the basal lamellar surface. Conversely, only lamellae that can be identified as untilted ‘‘edge-on’’ or ‘‘flat-on’’ in AFM images are suitable for thickness analysis. The average thickness obtained by these techniques is based on sampling microscopic areas and will only be correct if the morphology is uniform in the sample. Micrographs taken from different areas of the specimen are usually studied, and statistical analysis of histograms used for quantitative analysis [255,256]. SAXS is a major tool in characterizing lamellar structure. Direct application of Bragg’s law in a morphologically homogeneous system of stacks of lamellae provides the long period, which corrected with the crystallinity gives the lamellae thickness [257]. More elaborate procedures of analysis based on idealized models of alternating crystalline and non-crystalline regions include the one-dimensional electro-density correlation function [258–262] and the interphase distribution function [263,264]. Both are based on Fourier transformations of the scattering curve and yield quantitative information on the mean crystallite thickness, the most probable long spacing (or long period) and crystallinity within lamellar stacks or linear crystallinity. The results depend on the model assumed for the geometry of the lamellar stacks. If a model with diffuse interfaces is used, analysis of the SAXS data yields the thickness of the interfacial region [265]. The low-frequency LAM in Raman spectroscopy is a vibrational mode pertaining to ordered sequences in the chain direction. The mode frequency (Du) is inversely proportional to the ordered chain sequence length or to the crystallite thickness. This relation was given by Shimanouchi and co-workers [92,93] as: m E 1=2 Du ¼ (11) 2cLc r Here m is the mode order (m ¼ 1,3,5 y, usually 1 for polyethylenes), c the velocity of light, r the density of the vibrating sequence (density of pure crystal) and E the Young’s modulus in the chain direction. The LAM band has been observed in many polymers and has been widely used in structural studies of polyethylenes [94–99,266], as well as other semi-crystalline polymers, such as poly (ethylene oxide) [267], poly(methylene oxide) [268,269] and isotactic poly(propylene) [270,271]. The distribution of crystalline thickness can be obtained from the width of the LAM mode, corrected by temperature and frequency factors [272,273] as: hcDu fðLc Þ ¼ 1 exp (12) Du2 I obs u KT
Phase Structure and Morphology
285
I obs is the observed intensity of frequency Du and K the Boltzman constant. u The displacement of the LAM peak frequency due to this correction is negligible for LAMs that appear at frequencies of 15 cm1 or higher and have half-width less than B5 cm1 [273]. These conditions are usually fulfilled by n-alkanes. However, for broad LAM modes, for example those displayed by ethylene copolymers, displacements to higher frequencies of Du by Equation (12) may exceed 5 cm1 or more. In addition, the thicknesses obtained from Equation (12) need a correction for the tilt angle (angle between the chain direction and the basal surface of the lamellae). Depending on crystallization temperature, tilt angles between 151 and 451 have been observed in polyethylenes [255]. As seen in the example of Figure 20, when the tilt angle is taken into account, the lamellar thicknesses obtained by Raman LAM were in good agreement with those obtained by TEM. The crystallite thickness distribution determined by thinsection TEM is compared in this figure with the distribution obtained from the LAM mode prior and after correction for the tilt angle for a narrow fraction of linear polyethylene. After the correction is made, the agreement between both techniques is excellent. The application of Equation (11) to obtain the lamellar thickness of polymeric crystallites requires knowledge of the Young’s modulus, E. In a study of n-alkanes, a value of E of 358 GPa was obtained [274]. However, it was later recognized that the LAM frequencies of the low molecular weight n-alkanes are raised by longitudinal forces at the chain ends [275]. Thus, E for low molecular weight n-alkanes is higher than the value corresponding to the chain devoid of ends. When these factors are considered, a value of E ¼ 290 GPa was obtained for high molecular weight polyethylene chains [275]. It has also been shown that the interaction between layers decreases with chain length [276]. Raman LAM, SAXS and TEM have been used to obtain the dependence of crystallite thickness with molecular weight under rapid crystallization as well as
Figure 20 Normalized frequency distributions of crystallite thickness for linear polyethylene fraction, Mn ¼ 76,700, Mw ¼ 80,800 crystallized at 118 1C; (9), electron micrograph histogram; ( ), smooth distribution from electron micrograph; (K), uncorrected Raman LAM distribution; (J), Raman distribution corrected for 301 tilt. Reproduced with permission from Ref. [256]. Copyright John Wiley & Sons, Inc., 1989.
286
Rufina G. Alamo
250
Thickness (Å)
200 La 150
Lc
100 50 Lb 0 1.E+03
1.E+04
1.E+05
1.E+06
1.E+07
MW
Figure 21 Plot of thickness values as a function of molecular weight for linear polyethylene fractions quenched to 781C. (D), crystallite thickness, Lc; (J), interlamellar thickness, La; (K), interfacial thickness, Lb. Reprinted with permission from Ref. [277]. Copyright 1990 American Chemical Society.
for isothermally crystallized specimens. The crystallite thickness obtained by Raman LAM for rapidly crystallized polyethylene fraction remains constant at ˚ as molecular weight increases, as shown in Figure 21 [277]. Similar about 140 A constant thicknesses with chain length were obtained from TEM [255] and SAXS [278,279] of the rapidly crystallized fractions. Other polymers display the same trend [279–281]. It is, then, concluded that in general the lamellar thickness is independent of molecular weight for rapidly crystallized samples. Isothermally crystallized samples behave in a different manner. Lc was found to increase with increasing crystallization temperature for a narrow linear polyethylene fraction [282]. After rapid, non-isothermal crystallization a narrow ˚, size distribution is obtained. The crystallite thickness ranges from 120 to 150 A and is independent of the molecular weight in agreement with TEM data. After isothermal crystallization, there is a sharp increase in the crystallite thickness with crystallization temperature and a broad distribution develops. The increase in Lc with crystallization temperatures is not limited to polyethylene. Similar behavior has been obtained in poly(tetrafluoroethylene) [283], poly(ethylene terephthalate) [284], poly(aryl ether ether ketone) [285–287], poly(cis-isoprene) [288] and poly(ethylene oxide) [289] among others. It thus appears to be a general phenomenon. In summary, the structure and character of the lamellae formed by homopolymers and their thickness is strongly dependent on molecular weight and crystallization temperature. The structure can range from long, straight, stacked lamellae to ones that are short, curved and highly segmented. The lamellae thickness distribution also depends strongly on these variables.
3. CONCLUDING REMARKS The major components of the phase structure of semi-crystalline polymers and the most common techniques of characterization of the crystalline, amorphous
Phase Structure and Morphology
287
and intermediate phases have been described in this chapter. Most properties of crystalline polymers depend to a large extent on the relative content of these phases, which can be varied over very wide limits and in a very systematic manner by changing molar mass, molar mass distribution, structural regularity of the chain and crystallization conditions. The morphology of organized crystalline entities at a level above the crystallographic unit cell is also described. These entities are polymeric lamellae that integrate the long-chain connectivity between crystalline and non-crystalline regions. The thickness and extension of the lamellae are a function of molecular variables (length and structural regularity) and crystallization conditions. Lamellae may aggregate in a large variety of supermolecular structures, or branch following homoepitaxial growth. Examples throughout this chapter are given primarily for two of the most simple, best studied semi-crystalline polymers, the polyethylenes and poly(propylenes).
ACKNOWLEDGEMENTS The author acknowledges funding by the National Science Foundation and the assistance of Dr. K. Jeon and URP student S. Warnock with some of the reproductions.
REFERENCES 1 2 3 4 5 6 7 8 9 10 11 12 13
14 15 16 17 18 19 20 21
K.H. Storks, J. Am. Chem. Soc., 60 (1938) 1753. A. Keller, Phil. Mag., 2 (1957) 1171. E.W. Fischer, Z. Naturforsch, 129 (1957) 753. A. Keller, The morphology of crystalline polymers, Die. Makromol. Chemie, 34 (1959) 1. P.H. Geil, Polymer Single Crystals, Interscience, New York, 1963. A. Keller, MTP Int. Rev. Sci., 8 (1972) 105. D.Y. Yoon and P.J. Flory, Faraday. Dis. Chem. Soc., 68 (1979) 288. P.J. Flory, J. Am. Chem. Soc., 84 (1962) 2857. R.S. Stein, Structure and properties of polymer films. In: R.W. Lenz and R.S. Stein (Eds.), Polymer Science and Technology, Vol. 1. Press, New York, NY, 1973. J. Maxfield and L. Mandelkern, Macromolecules, 10 (1977) 1141. L. Mandelkern, M. Glotin and R.S. Benson, Macromolecules, 14 (1981) 22. R.C. Allen and L. Mandelkern, J. Polym. Sci., Polym. Phys. Ed., 20 (1982) 1465. J.D. Hoffman, G.T. Davis and J.I. Lauritzen, The rate of crystallization of linear polymers with chain folding. In: N.B. Hannay (Ed.), Treatise on Solid State Chemistry, , Plenum Press, New York, 1976. L. Mandelkern, The crystalline state. In: J.E. Mark, et al. (Eds.), Physical Properties of Polymers, 3rd ed., Cambridge University Press, Cambridge, 2003. L. Mandelkern, Polm. Eng. Sci., 9 (1969) 255. B. Wunderlich, Macromolecular Physics, Crystal Structure, Morphology and Defects, Vol. 1, Academic Press, New York, 1973. L. Mandelkern, Acc. Chem. Res., 9 (1976) 81. B. Heck, T. Hugel, M. Lijima, E. Sadiku and G. Strobl, New J. Phys., 1(17) (1999) 1. A. Keller, Polymer crystals, Rep. Prog. Phys., 31 (1968) 623; Organization of macromolecules in the solid state: A personal approach, J. Polym. Sci., 51C (1975) 7. J.D. Hoffman and G.T. Davis, J. Res. Natl. Bur. Stand., 79A (1975) 613. E.W. Fischer, Prog. Coll. Poly. Sci., 57 (1975) 149.
288
Rufina G. Alamo
22 L. Mandelkern, Morphology of semicrystalline polymers. In: Characterization of Materials Research: Ceramics and Polymers, Syracuse University Press, 1975, p. 369. 23 J.H. Magill, Treatise in Material Science, Vol. 10, Part A, Academic Press, New York, 1977, p. 1. 24 A. Keller, J. Polym. Sci., 59C (1977) 1. 25 A. Keller, Farad. Disc. Chem. Soc., 68 (1979) 145. 26 L. Mandelkern, Crystallization and melting. In: C. Booth and C. Price (Eds.), Comprehensive Polymer Science, Polymer properties, Ch. 11, Pergamon Press, New York, 1989. 27 A.S. Vaughan and D.C. Bassett, Crystallization and morphology. In: C. Booth and C. Price (Eds.), Comprehensive Polymer Science, Polymer Properties, Ch. 12, Pergamon Press, New York, 1989. 28 L. Mandelkern, Accounts Chem. Res., 23 (1990) 380. 29 P.J. Phillips, Report Prog. Phys., 53 (1990) 549. 30 L. Mandelkern, The structure of polymers crystallized in the bulk. In: M. Dosiere (Ed.), Crystallization of Polymers, NATO ASI Series, Kluwer Academic Publishers, The Netherlands, 1995, p. 25. 31 G. Strobl, Eur. Phys. J. E, 3 (2000) 165. 32 G. Strobl, Eur. Phys. J. E, 18 (2005) 295. 33 G. Strobl, Prog. Polym. Sci., 31 (2006) 398. 34 L.E. Alexander, X-ray Diffraction Methods in Polymer Science, Wiley, New York, 1969. 35 E.W. Fischer and G. Hinrichsen, Polymer, 7 (1966) 195. 36 A.P. Gray, Thermochim. Acta, 1 (1970) 563. 37 V.B.F. Mathot, In: V.B.F. Mathot (Ed.), Calorimetry and Thermal Analysis of Polymers, Hanser Pub., New York, 1994, p. 105. 38 G.R. Strobl and W. Hagedorn, J. Polym. Sci.: Polym. Phys., 16 (1978) 1181. 39 P.C. Painter, M.M. Coleman and J.L. Koenig, The Theory of Vibrational Spectroscopy and Its Application to Polymeric Materials, Wiley, New York, 1982. 40 R. Kitamaru and F. Horii, Adv. Polym. Sci., 26 (1978) 137. 41 R.P. Sheldon, J. Polym. Sci., Polym. Lett., B1 (1963) 655. 42 P.J. Flory, Pure Appl. Chem., 56 (1984) 305. 43 J.R. Isasi, L. Mandelkern, M.J. Galante and R.G. Alamo, J. Polym. Sci., Polym. Phys. Ed., 37 (1999) 323. 44 G. Farrow and I.M. Ward, Polymer, 1 (1960) 330. 45 G. Fallow and D. Preston, Br. J. Appl. Phys., 11 (1960) 353. 46 S.L. Aggarwal and G.P. Tilley, J. Polym. Sci., 18 (1955) 17. 47 J.E. Preedy, Br. Polym. J., 5 (1973) 13. 48 E.V. Gouinlock, J. Polym. Sci., Polym. Phys. Ed., 13 (1974) 961. 49 M.A. McRae and W.F. Maddams, Polymer, 18 (1977) 524. 50 P.H. Hermans and A. Weidinger, J. Appl. Phys., 19 (1948) 491. 51 G. Natta, P. Corradini and M. Cesari, R.C. Accad. Lincei, 22 (1957) 11. 52 Z. Mo and H. Zhang, J. Macrom. Sci. Rev. Macrom. Chem. Phys. C, 35 (1995) 555. 53 A. Weidinger and P.H. Hermans, Makromol. Chem., 50 (1961) 98. 54 A.G. Simanke and R.G. Alamo, Macromolecules, 34 (2001) 6959. 55 A.M. Hindeleh and D.J. Johnson, Polymer, 11 (1970) 666. 56 N.T. Wakelyn and P.R. Young, J. Appl. Polym. Sci., 10 (1966) 1421. 57 P.S. Dai, P. Cebe, M. Capel, R.G. Alamo and L. Mandelkern, Macromolecules, 36 (2003) 4042. 58 M. Kakudo and N. Dassai, X-ray Diffraction by Polymers, Amsterdam, 1972. 59 W. Ruland, Acta Crystallogr., 14 (1961) 1180. 60 W. Ruland, Polymer, 5 (1964) 89. 61 A.M. Hindeleh and D.J. Johnson, Polymer, 13 (1972) 423. 62 J.L. Dumbleton and B.B. Bowles, J. Polym. Sci. Polym. Phys. Ed., 4 (1966) 951. 63 P.R. Swan, J. Polym. Sci., 42 (1960) 525. 64 V.B.F. Mathot and M.F.J. Pijpers, J. Therm. Anal., 28 (1983) 349. 65 V.B.F. Mathot, Polymer, 25 (1984) 579. 66 V.B.F. Mathot and M.F.J. Pijpers, Thermochim. Acta, 151 (1989) 241. 67 V.B.F. Mathot, Thermochim. Acta, 355 (2000) 1.
Phase Structure and Morphology
289
68 ATHAS data bank, http://athas.prz.rzeszow.pl/ 69 M. Peeters, B. Goderis, C. Vonk, H. Reynaers and V. Mathot, J. Polym. Sci., Polym. Phys. Ed., 35 (1997) 2689. 70 W. Huang, MS Thesis, Florida State University, 1999. 71 J.D. Hoffman, J. Chem. Phys., 29 (1958) 1192 and S. Shanbhag, R.G. Alamo, Polymer, 49 (2008) 2515. 72 R. Alamo, R.C. Domszy and L. Mandelkern, J. Phys. Chem., 88 (1984) 6587. 73 T. Liu, Z. Mo, H. Zhang, H. Na and Z. Wu, Eur. Polym. J., 33 (1997) 913. 74 M. Glotin and L. Mandelkern, Coll. Polym. Sci., 260 (1982) 182. 75 L. Mandelkern and A.J. Peacock, Polym. Bull., 16 (1986) 529. 76 M. Failla, R.G. Alamo and L. Mandelkern, Polym. Testing, 11 (1992) 151. 77 L.H. Wang, R.S. Porter, H.D. Stidham and S.L. Hsu, Macromolecules, 24 (1991) 5535. 78 C. Shen, A.J. Peacock, R.G. Alamo, T.J. Vickers, L. Mandelkern and C.K. Mann, Appl. Spectrosc., 46 (1992) 1226. 79 R.G. Alamo and L. Mandelkern, Macromolecules, 24 (1991) 6480. 80 R.G. Alamo and L. Mandelkern, Macromolecules, 22 (1989) 1273. 81 L. Mankelkern, R.G. Alamo and M.A. Kennedy, Macromolecules, 23 (1990) 4721. 82 R.G. Alamo, R.H. Glaser and L. Mandelkern, J. Polym. Sci., Polym. Phys. Ed., 26 (1988) 2169. 83 A.J. Melveger, J. Polym. Sci., Part A-2, 10 (1972) 317. 84 N. Everall, K. Davis, H. Owen, M.J. Pelletier and J. Slater, Appl. Spectrosc., 50 (1996) 388. 85 N. Everall, P. Taylor, J.M. Chalmers, D. MacKerron, R. Ferwerda and J.H. van der Mass, Polymer, 35 (1994) 3184. 86 C. Minogianni, G.K. Gatos and C. Galiotis, Appl. Spectrosc., 59 (2005) 1141. 87 A.S. Nielsen, D.N. Batchelder and R. Pyrz, Polymer, 43 (2002) 2671. 88 N. Everall, J.M. Chalmers, R. Ferwerda, J.H. van der Mass and P.J. Hendra, J. Raman Spec., 25 (1994) 43. 89 R.J. Lehnert, P.J. Hendra and N. Everall, Polymer Comm., 36 (1995) 2473. 90 R.J. Lehnert, P.J. Hendra, N. Everall and N.J. Clayden, Polymer, 38 (1997) 1521. 91 J. Dybal, P. Schmidt, J. Baldrian and J. Kratochvil, Macromolecules, 31 (1998) 6611. 92 S. Mizushima and T. Shimanouchi, J. Am. Chem. Soc., 71 (1940) 1320. 93 R.F. Schaufele and T. Shimanouchi, J. Chem. Phys., 47 (1967) 3605. 94 A. Hartley, Y.K. Leung, C. Booth and I.W. Shepherd, Polymer, 17 (1976) 354. 95 P.J. Hendra and H.A. Majid, Polymer, 18 (1977) 573. 96 G.R. Strobl and R. Eckel, J. Polym. Sci., Polym. Phys. Ed., 14 (1976) 913. 97 G.V. Fraser, Polymer, 19 (1978) 857. 98 M. Glotin and L. Mandelkern, J. Polym. Sci., Polym. Phys. Ed., 21 (1983) 29. 99 M. Glotin and L. Mandelkern, J. Polym. Sci., Polym. Lett. Ed., 21 (1983) 807. 100 R.G. Snyder, J. Chem. Phys., 76 (1982) 3921. 101 R.G. Snyder and S.L. Wunder, Macromolecules, 19 (1986) 496. 102 R.G. Snyder, N.E. Schlotter, R. Alamo and L. Mandelkern, Macromolecules, 19 (1986) 621. 103 W.L. Mattice, R.G. Snyder, R. Alamo and L. Mandelkern, Macromolecules, 19 (1986) 2404. 104 C.C. Naylor, R.J. Meier, B.J. Kip, K.P.J. Williams, S.M. Mason, N. Conroy and D.L. Gerrard, Macromolecules, 28 (1995) 2969. 105 F. Rull, A.C. Prieto, J.M. Casado, F. Sobron and H.G.M. Edwards, J. Raman Spectrosc., 24 (1993) 545. Also W. Lin, M. Cossar and V. Dang, J. Polym. Testing, 26 (2007) 814. 106 L. Mandelkern, Polym. J., 17 (1985) 337. 107 H. Hagemann, R.G. Snyder, A.J. Peacock and L. Mandelkern, Macromolecules, 22 (1989) 3600. 108 N.C. Tobin and M.J. Carrano, J. Polym. Sci., 24 (1951) 93. 109 D.R. Rueda, A. Hidalgo and F.J. Balta Calleja, Spectrochim. Acta Part A, 34 (1978) 475. 110 T. Okada and L. Mandelkern, J. Polym. Sci., Polym. Phys. Ed., 5 (1967) 239. 111 H. Hendu and G. Schell, Kunstoffe, 51 (1961) 69. 112 J.C. Rodriguez-Cabello, J. Martin-Monge, J.M. Lagaron and J.M. Pastor, Macrom. Chem. Phys., 199 (1998) 2767. 113 R.J. Meier, Soft Materials, 3 (2005) 45. 114 A.R. Wedgewood and J.C. Seferis, Pure Appl. Chem., 55 (1983) 873.
290
115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150
151 152 153 154 155 156 157
Rufina G. Alamo
L. Brambilla and G. Zerbi, Macromolecules, 38 (2005) 3327. V.M. Hallmark, S.P. Bohan, H.L. Strauss and R.G. Snyder, Macromolecules, 24 (1991) 4025. C. Gabriel, D. Lilge and M.O. Kristen, Macrom. Rapid Comm., 24 (2003) 109. K. Tashiro, S. Sasaki and M. Kobayashi, Macromolecules, 29 (1996) 7460. G.A. Voyiatzis, K.S. Andrikopoulos, G.N. Papatheodorou, E.I. Kamitsos, G.D. Chyssikos, J.A. Kapoutsis, S.H. Anastasiadis and G. Fytas, Macromolecules, 33 (2000) 5613. M. Takahashi, K. Tashiro and S. Amiya, Macromolecules, 32 (1999) 5860. K. Bergmann and K. Mawolki, Koll. Z-Z Polym., 219 (1967) 132. ibid., 251 (1973) 962. K. Bergmann, J. Polym. Sci.: Polym. Phys. Ed., 16 (1978) 1611. R. Kitamaru and F. Horii, Adv. Polym. Sci., 26 (1978) 139. W.L. Earl and D.L. VanderHart, Macromolecules, 12 (1979) 762. R. Kitamaru, F. Horii and K. Murayama, Macromolecules, 19 (1986) 636. R. Kitamaru, Adv. Polym. Sci., 137 (1998) 42 Springer-Verlag. Y. Shimizu, Y. Harashina, Y. Sugiura and M. Matsuo, Macromolecules, 28 (1995) 6889. D.E. Axelson and K.E. Russell, Prog. Polym. Sci., 11 (1985) 221. J. Chen, M. Fore, V.N. Reddy, K.B. Schwartz, H.P. Fisher and B. Wunderlich, J. Polym. Sci.: Pt. B: Polym. Phys., 32 (1994) 2683. C. Hedesiu, D.E. Demco, R. Kleppinger, A.A. Buda, B. Blumich, K. Remerie and V.M. Litvinov, Polymer, 48 (2007) 763. L. Zhang, Z. Liu, Q. Chen and E.W. Hansen, Macromolecules, 40 (2007) 5411. M. Wang, G.M. Bernard, R.E. Wasylishen and P. Choi, Macromolecules, 40 (2007) 6594. L. Hillebrand, A. Schmidt, A. Bolz, M. Hess, W. Veeman, R.J. Meier and G. van der Velden, Macromolecules, 31 (1998) 5010. A.G. Simanke, R.G. Alamo, G.B. Galland and R.S. Mauler, Macromolecules, 34 (2001) 6959. A.M.E. Baker and A.H. Windle, Polymer, 42 (2001) 667. K.E. Russell, B.K. Hunter and R.D. Heyding, Eur. Polym. J., 2/3 (1993) 211. D.C. McFaddin, K.E. Russell, G. Wu and R.D. Heyding, J. Polym. Sci., Polym. Phys. Ed., 31 (1993) 175. K. Monar and A. Habenschus, J. Polym. Sci., Polym. Phys. Ed., 37 (1999) 3401. C.M. Guttman, E.A. DiMarzio and J.D. Hoffman, Polymers, 22 (1980) 1466. R.C. Lacher, J.L. Bryant, L.N. Howard and D.W. Sumners, Macromolecules, 19 (1986) 2639. R.C. Lacher, J.L. Bryant and L.N. Howard, J. Chem. Phys., 85 (1986) 6147. R.C. Lacher, Macromolecules, 20 (1987) 3054. J.A. Marqusee and K.A. Dill, Macromolecules, 19 (1986) 2420. D. Yoon and P.J. Flory, Farady Discuss. Chem. Soc., 68 (1979) 288. J.M. Carella, W.W. Graessley and L.J. Fetters, Macromolecules, 17 (1984) 2775. W.L. Mattice, Macromolecules, 19 (1986) 2303. A. Aji, J. Guevremont, K.C. Cole and M.M. Dumoulin, Polymer, 37 (1996) 3707. S.B. Lin and J.L. Koenig, J. Polym. Sci., Polym. Phys. Ed., 20 (1982) 2277; J. Liu and J.L. Koenig, Anal. Chem., 59 (1987) 2609. K. Schmidt-Rohr, W. Hu and N. Zumbuliadis, Science, 280 (1998) 714. A. Dupasquier and A.P. Mills Jr. (Eds.), Positron Spectroscopy of Solids. Proceedings of the International School of Physics Enrico Fermi, Course CXXV, Varenna 6–16 July, 1993, IOS Press, Amsterdam, 1995. O.E. Mogensen, Positron Annihilation in Chemistry, Springer, Berlin, Heidelberg, 1995. W. Brant and A. Dupasquier (Ed.), Positrons Solid State Physics. Proceedings of the International School of Physics ‘‘Enrico Fermi’’, Course LXXXIII, Varenna 1981, North Holland, Amsterdam, 1983. G. Dlubek, K. Saarinen and H.M. Fretwell, J. Polym. Sci., Polym. Phys. Ed., 36 (1998) 1513. G. Dlubek, J. Stejny, Th. Lupke, D. Bamford, K. Petters, Ch. Hubner, A.M. Alam and M.J. Hill, J. Polym. Sci., Polym. Phys. Ed., 40 (2002) 65. G. Dlubek, Th. Lupke, J. Stejny, A.M. Alam and M. Arnold, Macromolecules, 33 (2000) 990. G. Dlubek, D. Bamford, A. Rodriguez-Gonzalez, S. Bornemann, J. Stejny, B. Schade, M.A. Alam and M. Arnold, J. Polym. Sci., Polym. Phys. Ed., 40 (2002) 434. G. Dlubek, D. Bamford, O. Henschke, J. Knorr, A.M. Alam, M. Arnold and Th. Lupke, Polymer, 42 (2001) 5381.
Phase Structure and Morphology
291
158 D. Kilburn, D. Bamford, Th. Lupke, G. Dlubek, T.J. Menke and M.A. Alam, Polymer, 43 (2002) 6973. 159 M.L. Cerrada, E. Perez, J.M. Perena, R. Benavente, M. Misheva and T. Grigorov, Macromolecules, 38 (2005) 8430. 160 S. Saito, Y. Moteki, N. Nakagawa, F. Horii and R. Kitamaru, Macromolecules, 23 (1996) 3256. 161 D.E. Axelson, Carbon13 Solid State NMR of Crystalline Polymers, In: R.A. Komoroski (Ed.), High Resolution NMR Spectroscopy of Synthetic Polymers in Bulk, VCH, Deerfield Beach, Florida, USA, 1986. 162 D.E. Axelson, L. Mandelkern, R. Popli and P. Mathieu, J. Polym. Sci.: Polym. Phys. Ed., 21 (1983) 2319. 163 R.G. Alamo, J.A. Blanco, I. Carrilero and R. Fu, Polymer, 43 (2002) 1857. 164 R.A. Komoroski, J. Maxfield and L. Mandelkern, Macromolecules, 10 (1977) 545. 165 R.A. Komoroski, J. Maxfield, F. Sakoguchi and L. Mandelkern, Macromolecules, 10 (1977) 550. 166 D.E. Axelson and L. Mandelkern, In: W.F. Pasoka (Ed.), Carbon13 NMR in Polymer Science, ACS Symposium Series No. 103, Washington, 1979, p. 181. 167 R.G. Alamo and L. Mandelkern, Thermochim. Acta, 238 (1994) 155. 168 X. Jin, T.S. Ellis and F.E. Kanasz, J. Polym. Sci., 22 (1984) 1701. 169 G.E. Wissler and B. Crist, Jr., J. Polym. Sci., Polym. Phys. Ed., 18 (1980) 1257. 170 B. Wunderlich and S.Z.D. Cheng, Gaz. Chim. Ital., 116 (1986) 345. 171 P.P. Huo and P. Cebe, Macromolecules, 25 (1992) 902. 172 D.P. Heberer, S.Z.D. Cheng, J.S. Barley, S.H. Lieu, R.G. Bryant and F.W. Harris, Macromolecules, 24 (1991) 1896. 173 S.X. Lu and P. Cebe, Polymer, 37 (1996) 4857. 174 P.P. Huo and P. Cebe, Macromolecules, 26 (1993) 5561. 175 L. Mandelkern, Chemtracts-Macromol. Chem., 3 (1992) 347. 176 B. Goderis, P.G. Klein, S.P. Hill and C.E. Koning, Prog. Colloid Polym. Sci., 130 (2005) 40. 177 P.P. Huo and P. Cebe, Colloid Polym. Sci., 270 (1992) 840. 178 P. Huo and P. Cebe, J. Polym. Sci. Polym. Phys., 30 (1992) 239. 179 D.S. Kalika and R.K. Krishnaswamy, Macromolecules, 26 (1993) 4252. 180 E. Schlosser and A. Scho¨nhals, Coll. Polym. Sci., 267 (1989) 963. 181 R. Kitamaru, F. Horri and S.H. Hyon, J. Polym. Sci.: Polym. Phys. Ed., 15 (1977) 821. 182 C. Choi, L. Bailey, A. Rudin and M.K. Pinar, J. Polym. Sci.: Pt. B: Polym. Phys., 35 (1997) 2551. 183 R.R. Eckman, P.M. Heinricks and A.J. Peacock, Macromolecules, 30 (1997) 2474. 184 H. Uhera, T. Aoike, T. Yamanobe and T. Komoto, Macromolecules, 35 (2002) 2640. 185 E.W. Hansen, P.E. Kristiansen and B. Pedersen, J. Phys. Chem. B, 102 (1980) 5444. 186 T. Kawagueki, A. Mamoda, Y. Hosokawa and F. Horu´i, Polymer, 39 (1998) 2725. 187 Y. Shimizu, Y. Harashina, Y. Sugiura and M. Matsuo, Macromolecules, 28 (1995) 6889. 188 D.E. Axelson and K.E. Russell, Prog. Polym. Sci., 11 (1985) 221. 189 J. Chen, M. Fore, V.N. Reddy, K.B. Schwartz, H.P. Fisher and B. Wunderlich, J. Polym. Sci.: Pt. B: Polym. Phys., 32 (1994) 2683. 190 S. Saito, Y. Moteki, M. Nakagawa, F. Horri and R. Kitamaru, Macromolecules, 23 (1990) 3256. 191 H. Kagi and F. Horii, Macromolecules, 30 (1997) 5791. 192 A. Hirai, F. Horii, R. Kitamaru, J.G. Fatou and A. Bello, Macromolecules, 23 (1990) 2913. 193 B. Goderis, P.G. Klein, S.P. Hill and C.E. Koning, Prog. Colloid Polym. Sci., 130 (2005) 40. 194 A.L. Cholli, J.J. Dumais, A.K. Engel and L.W. Jelinski, Macromolecules, 17 (1984) 2399. 195 K. Takegoshi, I. Tanaka, K. Hikichi and S. Higashida, Macromolecules, 25 (1992) 3392. 196 T. Takehiko, S. Maeda and A. Saika, Macromolecules, 16 (1983) 1535. 197 P. Sozzani, R. Simonatti and M. Galimberti, Macromolecules, 26 (1993) 5782. 198 L. Abis, E. Merlo and R. Po., J. Polym. Sci.: Pt. B: Polym. Phys., 33 (1995) 691. 199 M.D. Paliks and J. Schaefer, Macromolecules, 23 (1990) 3426. 200 M. Wilhelm and H.W. Spiess, Macromolecules, 29 (1996) 1088. 201 D.C. Bassett, Principles of Polymer Morphology, Cambridge University Press Ed., London, 1981. 202 G. Kanig, Prog. Colloid Polym. Sci., 57 (1975) 176. 203 R.H. Olley, A.M. Hodge and D.C. Bassett, J. Polym. Sci., Polym. Phys. Ed., 17 (1979) 627. 204 G.M. Brown and J.H. Butler, Polymer, 38 (1997) 3937.
292
Rufina G. Alamo
205 A.E. Woodward, In: E.H. Immergat (Ed.), Understanding Polymer Morphology, Hanser/Gardner Publisher, Ohio, USA, 1995. 206 D.A. Ivanov and A.M. Jonas, Macromolecules, 32 (1582). 207 D.A. Ivanov, B. Nysten and A.M. Jonas, Polymer, 40 (1999) 5899. 208 D.A. Ivanov and S. Magonov, Atomic force microscopy studies of semicrystalline polymers at variable temperature. In: G. Reiter, J.-V. Sommer (Eds.), Polymer Crystallization, Springer, Berlin, 2003, p. 98. 209 G. Reiter, J. Polym. Sci., Polym. Phys. Ed., 41 (2003) 1869. 210 H. Schenherr, D. Sneting and G.J. Vancso, Polym. Bull., 30 (1993) 567. 211 Y.G. Lei, C.M. Chan, J.X. Li, K.M. Ngad and Y. Wang, Macromolecules, 35 (2002) 6751. 212 B. Poon, M. Rogunova, A. Hiltner, E. Baer, S.P. Chum, A. Galeski and E. Piorkowska, Macromolecules, 38 (2005) 1232. 213 F. Khoury and E. Passaglia, The morphology of crystalline synthetic polymers. In: N.B. Hannay (Ed.), Treatise on Solid State Chemistry, 3rd ed., Plenum Press, New York, 1976, p. 335. 214 G. Chiu, R.G. Alamo and L. Mandelkern, J. Polym. Sci., Polym. Phys. Ed., 28 (1990) 1207. 215 E.W. Fischer, Z. Naturforsch, 12 (1957) 753. 216 M. Takayanagi and T. Yamashita, J. Polym. Sci.: Poly. Lett. Ed., 22 (1956) 552. 217 W.T. Chuang, P.D. Hong and H.H. Chuak, Polymer, 45 (2004) 2413. 218 R.C. Allen and L. Mandelkern, J. Polym. Sci.: Poly. Phys. Ed., 20 (1982) 1465. 219 R. Alamo, J.G. Fatou and J. Guzman, Polymer, 23 (1982) 379. 220 J.D. Hoffman, G.T. Davis and J.I. Lauritzen, Jr., In: N.B. Hannay (Ed.), Treatise on Solid State Chemistry, , Plenum Press, New York, 1976 . 221 E.J. Clark and J.D. Hoffman, Macromolecules, 17 (1984) 878. 222 J. Maxfield and L. Mandelkern, Macromolecules, 10 (1977) 1141. 223 L. Mandelkern, M. Glotin and R.S. Benson, Macromolecules, 14 (1981) 22. 224 L. Mandelkern, In: D.A. Young (Ed.), Organization of Macromolecules in the Condensed Phase; Dis. Faraday Soc., 68 (1979) 310. 225 T. Hashimoto, K. Nagatoshi, A. Todo and H. Kawai, Polymer, 17 (1976) 1075. 226 T. Hashimoto, Y. Marakami and H. Hawai, J. Polym. Sci., Polym. Phys. Ed., 13 (1975) 1613. 227 L. Mandelkern, K.W. McLaughlin and R.G. Alamo, Macromolecules, 25 (1992) 1440. 228 L. Mandelkern and J. Maxfield, J. Polym. Sci., Polym. Phys. Ed., 17 (1979) 1913. 229 M. Glotin and L. Mandelkern, Macromolecules, 14 (1981) 1394. 230 I.G. Voigt-Martin, D.W. Fischer and L. Mandelkern, J. Polym. Sci.: Polym. Phys. Ed., 8 (1980) 2347. 231 I.G. Voigt-Martin and L. Mandelkern, J. Polym. Sci.: Polym. Phys. Ed., 19 (1981) 1769. idem 22 (1984) 1901. 232 F. Khoury, J. Res. Nat. Bur. St., 70A (1966) 29. 233 D.C. Bassett and R.H. Olley, Polymer, 26 (1985) 704. 234 D.R. Norton and A. Keller, Polymer, 26 (1985) 704. 235 B. Lotz and J.C. Wittmann, J. Polym. Sci., Polym. Phys. Ed., 24 (1986) 1541. 236 F.J. Padden and H.D. Keith, J. Appl. Phys., 44 (1973) 1217. 237 F.L. Binsbergen and B.G.M. de Lange, Polymer, 9 (1968) 23. 238 B.J. Lotz, Macrom. Sci. Part B, 41 (2002) 685. 239 R.G. Alamo and C. Chi, Crystallization behavior and properties of polyolefins. In: Y. Morishima, T. Norisuye and K. Tashiro (Eds.), Molecular Interactions and Time-Space Organization in Macromolecular Systems, Springer, New York, 1999, p. 29. 240 R.G. Alamo, G.M. Brown, L. Mandelkern, A. Lehtinen and R. Paukkeri, Polymer, 40 (1999) 3933. 241 T.W. Huang, R.G. Alamo and L. Mandelkern, Macromolecules, 22 (1999) 6347. 242 P.S. Dai, P. Cebe, M. Capel, R.G. Alamo and L. Mandelkern, In: P. Cebe, B. Hsiao and D. Lohse (Eds.), Scattering from Polymers. Characterization by X-rays, Neutrons and Light. ACS Symposium Series, Washington DC, 2000, p. 152. 243 P.S. Dai, P. Cebe, M. Capel, R.G. Alamo and L. Mandelkern, Macromolecules, 36 (2003) 4042. 244 B. Lotz, J.C. Wittman and A.J. Lovinger, Polymer, 37 (1996) 4979. 245 S. Bru¨ckner, S.U. Meille, U. Petraccone and B. Pirozzi, Prog. Polym. Sci., 16 (1991) 361. 246 I.L. Hosier, R.G. Alamo and J.S. Lin, Polymer, 45 (2004) 3441.
Phase Structure and Morphology
247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287
288 289 290 291
293
R. Thomann, C. Wang, J. Kressler and R. Mulhaupt, Macromolecules, 29 (1996) 8425. R.G. Alamo, M.-H. Kim, M.J. Galante, J.R. Isasi and L. Mandelkern, Macromolecules, 32 (1999) 4050. F. Auriemma and C. De Rosa, Macromolecules, 35 (2002) 9057. I.L. Hosier, R.G. Alamo, P. Esteso, J.R. Isasi and L. Mandelkern, Macromolecules, 36 (2003) 5623. C. De Rosa, F. Auriemma, O. Ruiz de Ballesteros, L. Resconi and I. Camurati, Macromolecules, 40 (2007) 6600. B. Lotz, S. Graff, S. Straupe and J.C. Wittman, Polymer, 32 (1991) 2902. R.G. Alamo, A. Ghosal, J. Chatterjee and K.L. Thomson, Polymer, 46 (2005) 8774. Y. Chiary, K. Vadlamudi, M. Jeon, R. Chella and R.G. Alamo, Polymer, 48 (2007) 3170. I.G. Voigt-Martin, Adv. Polym. Sci., 67 (1985) 196. I.G. Voigt-Martin, G.M. Stack, A.J. Peacock and L. Mandelkern, J. Polym. Sci.: Pt. B: Polym. Phys., 27 (1989) 957. F.J. Balta-Calleja and C.G. Vonk, X-ray Studies of Synthetic Polymers. Elsevier Publisher, New York, 1989. C.G. Vonk and G. Kortleve, Kolloid-Z, 220 (1967) 10. C.G. Vonk and G. Kortleve, Kolloid-Z, 221 (1968) 124. C.G. Vonk, J. Appl. Crystallogr., 11 (1978) 535. G. Strobl and M. Schneider, J. Polym. Sci., Polym. Phys. Ed., 18 (1980) 1343. C. Santa Cruz, N. Stribeck, H.G. Zachmann and F.J. Balta Calleja, Macromolecules, 24 (1991) 5980. W. Ruland, Colloid Polym. Sci., 255 (1977) 417. N. Stribeck and W. Ruland, J. Appl. Crystallogr., 11 (1978) 535. N. Stribeck, R.G. Alamo, L. Mandelkern and H.G. Zachmann, Macromolecules, 28 (1995) 5029. P.M. Pakhomov, S. Khizhnyak, V. Golitsyn, E. Ruhl, V. Vasileva and A. Tshmel, J. Macromol. Sci., Phys., B41 (2002) 229. A. Hartley, Y.K. Leung and C. Booth, Polymer, 17 (1976) 354. J.F. Rabolt and B. Fanconi, J. Ploym. Sci., Polym. Lett. Ed., 15 (1977) 121. J.F. Rabolt, Crit. Rev. Solid State Mater. Sci., 12 (1985) 165. S.L. Hsu, S. Kimm, S. Krause and G.S.Y. Yeh, J. Ploym. Sci., Polym. Lett. Ed., 14 (1976) 195. P.J. Hendra, J. Vile, H.A. Willis, V. Zichy and M.E.A. Cudby, Polymer, 25 (1984) 785. R.G. Snyder, S.J. Krause and J.R. Scherer, J. Polym. Sci., Polym. Phys. Ed., 16 (1978) 1593. R.G. Snyder and J.R. Scherer, J. Polym. Sci., Polym. Phys. Ed., 18 (1980) 421. R.F. Schaufele and T. Shimanouchi, J. Chem. Phys., 47 (1967) 3605. G.R. Strobl and R. Echel, J. Polym. Sci.: Polym. Phys. Ed., 14 (1976) 913. R.G. Snyder, H.L. Strauss, R.G. Alamo and L. Mandelkern, J. Chem. Phys., 100 (1994) 542. L. Mandelkern, R.G. Alamo and M.A. Kennedy, Macromolecules, 23 (1990) 4721. C. Manega, A. Marigo, G. Cingano, R. Zannetti and G. Paganetto, Polymer, 37 (1996) 5549. E. Robelin-Souffache´ and J. Rault, Macromolecules, 22 (1989) 3581. C. Fougnies, M. Dosiec?e, M.H.J. Koch and J. Roovers, Macromolecules, 31 (1998) 6266. J.H. Magill, J.M. Schultz and J.S. Lin, Coll. Polym. Sci., 265 (1987) 193. L. Mandelkern, Acc. Chem. Res., 23 (1990) 380. D.C. Bassett and R. Davitt, Polymer, 15 (1974) 721. H.G. Zachmann and R. Gehrkes, Morphology of Polymers, Walter de Gruyter Co., Berlin, 1986, p. 119. J. Wang, M. Alvanez, W. Zhang, Z. Wu, Y. Li and B. Chu, Macromolecules, 25 (1992) 6943. B.S. Hsiao and K.H. Gardner, In: M. Dosie´re (Ed.), Crystallization of Polymers, NATO ASI Series, Series C: Mathematical and Physical Sciences, Vol. 405. Kluwer Academic, Boston, 1993, p. 415. M. Dosie´re, C. Fougnies, M.H.J. Koch and J. Roovers, In: P. Cebe, B.S. Hsiao and D. Lohse (Eds.), Scattering from Polymers. Characterization by X-rays, Neutrons and Light. ACS Symposium Series No. 739, Washington DC, 2000, p. 166. E.H. Andrews, Pure Appl. Chem., 31 (1972) 91. J.P. Arlie, P. Spegt and A. Skoulios, Die Makrom. Chem., 104 (1967) 212. J. Cheng, M. Fone, V. Nireddy, K.B. Schwartz, H.P. Fisher and B. Wunderlich, J. Polym. Sci.: Pt. B: Polym. Phys., 32 (1994) 2683. H. Kaji and F. Horii, Macromolecules, 30 (1997) 5791.
This page intentionally left blank
CHAPT ER
8 Characterization of Molecular Orientation Thierry Lefe`vre, Christian Pellerin and Michel Pe´zolet
Contents
1. Introduction 2. Theory 2.1 The orientation distribution function 2.2 Biaxial distribution 2.3 Uniaxial distribution 2.4 Relationships between the order parameters and the shape of the ODF 3. Birefringence 3.1 Refractometry method 3.2 Compensation method 3.3 Transmission method 4. Infrared Linear Dichroism (IRLD) 4.1 Transmission IRLD 4.2 Reflection IRLD 4.3 Time-resolved IRLD 5. Raman Spectroscopy and Microspectroscopy 5.1 Conventional Raman spectroscopy (macro-Raman) 5.2 Spectromicroscopy (micro-Raman) 6. Fluorescence Spectroscopy 7. NMR Spectroscopy 8. X-Ray Diffraction and Absorption 9. Conclusion References
295 297 297 299 300 300 301 303 303 304 305 307 309 312 313 314 319 322 325 328 333 333
1. INTRODUCTION The physical properties of materials, especially their mechanical properties, are intimately related to their structural organization at all length scales. It is Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00408-X
r 2008 Elsevier B.V. All rights reserved.
295
296
Thierry Lefe`vre et al.
therefore of prime importance, from fundamental and practical viewpoints, to characterize the microstructure and crystallinity of the materials as well as their molecular conformation and orientation. The presence of molecular orientation in macromolecules leads to anisotropic physical properties. For instance, the modulus, toughness, electrical conductivity, etc., can widely differ along the longitudinal, transverse, or normal directions in highly oriented samples. Biomaterials made of fibrous proteins, such as collagen, keratin, or silk fibroin, often exhibit a multitude of anisotropic mechanical properties with important biological roles. These functions are related to a specific orientational and structural organization that has been optimized during thousands or millions of years of evolution. The dragline silk (the lifeline) of spiders, for instance, has a high strength, which is combined with a high extensibility, providing a toughness unmatched by any polymeric material. The biosynthesis of such biological materials is uniquely adapted because it allows precise specification of hierarchical order at all levels. For synthetic polymers, orientation is introduced during the processing operations such as molding, extrusion, drawing, rolling, or spinning. Kevlars (aramid fibers) and Dyneemas (polyethylene (PE) fibers) are examples of such highly oriented polymeric materials that are employed in different modern applications. Molecular orientation is also at the origin of the shrinkage phenomenon that can be observed for synthetic and natural fibers when subjected to a rise in temperature or relative humidity. The appropriate quantification of the degree of orientation has different motivations. First, it can provide a detailed knowledge about the structure of materials. In particular, the understanding of natural biopolymer organization is a basic paradigm to enable manufacturing biomimetic specimens with comparable properties. Quantitation of orientation can also provide knowledge about how and to what extent the orientation level relates to particular mechanical properties. There is also an important need, from a technological standpoint, to understand the influence of the processing method, temperature, strain rate, heat setting treatments, and cooling rate on the orientation level and final properties. Finally, many research activities are devoted to the investigation of the molecular disorientation occurring during the relaxation of polymeric chains in samples subjected to mechanical constraint because such molecular reorganization can compromise the sought anisotropic properties. The aim of this chapter is to describe how different physical techniques can provide useful quantitative data for the evaluation of molecular orientation and to emphasize their possibilities and limitations. The aim is not to present an exhaustive review on this subject. More details and applications can be found in the original articles and relevant books cited in the bibliography. The mathematical description of orientation will first be presented following the formalism introduced by Roe and Krigbaum [1,2] over forty years ago and nowadays commonly used in the scientific community. This formalism is based on the description of the orientation distribution function (ODF) as an expansion of weighted spherical harmonics, the weighted coefficients being the so-called order parameters. The methods most commonly used to study molecular orientation in samples having uniaxial or biaxial symmetry will then be
Characterization of Molecular Orientation
297
presented in the order of increasing number of order parameters that can be determined by each technique. Based on this criterion, birefringence and infrared (IR) spectroscopy will be presented first. Indeed, they offer the simplest ways of obtaining the second moment of the orientation function. Polarized Raman spectroscopy and fluorescence spectroscopy that allow the determination of the second and fourth moments of the orientation function will then be presented. Finally, nuclear magnetic resonance (NMR) spectroscopy and X-ray diffraction, which are techniques that lead to the most detailed description of the ODF, will be presented. Both techniques allow the determination of higher moments of the ODF, X-ray diffraction providing the complete ODF of the crystalline phase of semicrystalline polymers.
2. THEORY 2.1 The orientation distribution function For most systems, the characterization of orientation essentially consists in the determination of the distribution of orientation of some structural units (crystallites, chain segments, chemical groups, etc.) dispersed within a sample. This problem reduces to the determination of the orientation of a local Cartesian coordinate system, Oxyz, linked to the structural unit, relative to a second macroscopic Cartesian coordinate system, OXYZ, linked to the sample. The first coordinate system can be related to the second using the Euler angles (y, j, c) as shown in Figure 1. The angles y and f, which represent the inclination and azimuth of the structural unit, respectively, allow specifying the orientation of the Oz-axis in the macroscopic coordinate system. To completely define the orientation of the structural unit, it is necessary to define the third angle, c, specifying its rotation about the Oz-axis. For fibers or samples with uniaxial symmetry, the OZ-axis corresponds to the axis of symmetry. For biaxial samples, OZ is the machine direction (MD) and OX the transverse direction (TD), OY being perpendicular to the plane of the film (normal direction, ND). When referring to polymer filming processes, the MD may be called the forward draw direction (FD) and the TD may be referred to as the sideways (draw) direction (SD). The orientation is not strictly identical for all structural units and is rather spread over a certain statistical distribution. The distribution of orientation can be fully described by a mathematical function, N(y, j, c), the so-called ODF. Based on the theory of orthogonal polynomials, Roe and Krigbaum [1,2] have shown that N(y, j, c) can be expanded as a series of generalized spherical harmonics that form a complete set of orthogonal functions, so that Nðy; j; cÞ ¼
1 X ‘ ‘ X X
u‘mn Z‘mn ðx ¼ cos yÞ eimj einc
(1)
‘¼0 m¼‘ n¼‘
The quantity Nðy; j; cÞ sin ydydjdc represents the fraction of structural units oriented in the generalized solid angle sinydydfdc, with the following
298
Thierry Lefe`vre et al.
Z
z
x y
Structural unit
O
Y
X
Figure 1 Definition of the coordinate systems Oxyz and OXYZ and Euler angles y, j, and c.
normalization condition Z pZ
2p
Z
2p
Nðy; j; cÞ sin ydydjdc ¼ 1 0
0
(2)
0
The functions Z‘mn ðx ¼ cos yÞ are a generalization of associated Legendre functions and the coefficients of the series u‘mn are given by Z p Z 2p Z 2p 1 Nðy; j; cÞ Z‘mn ðx ¼ cos yÞ eimj einc sin ydydjdc (3) u‘mn ¼ 2 4p 0 0 0 The u‘mn coefficients are the mean values of the generalized spherical harmonics calculated over the distribution of orientation and are called order parameters. These are the quantities that are measurable experimentally and their determination allows the evaluation of the degree of molecular orientation. Since the different characterization techniques are sensitive to specific energy transitions and/or involve different physical processes, each technique allows the determination of certain u‘mn parameters as described in the following sections. These techniques often provide information about the orientation of a certain physical quantity (a vector or a tensor) linked to the molecules and not directly to that of the structural unit itself. To convert the distribution of orientation of the measured physical quantity into that of the structural unit, the Legendre addition theorem should be used [1,2]. An example of its application is given for IR spectroscopy in Section 4.
Characterization of Molecular Orientation
299
It should be noted that the functions Z‘mn ðx ¼ cos yÞ may assume the following normalized forms [1,2] Z p ðZ‘mn ðx ¼ cos yÞÞ2 sin y dy ¼ 1 (4) 0
For the non-normalized forms, the u‘mn coefficients have to be replaced by the coefficients hP‘mn i that differ by a numerical factor so that [3] 4p2 hP‘mn i ¼ u‘mn (5) N ‘mn with 2‘ þ 1 ðl þ mÞ! ðl nÞ! 1 N 2‘mn ¼ (6) 2 ðl mÞ! ðl þ nÞ! ½ðm nÞ!2 The non-normalized forms are most commonly found in the literature and will be used throughout the rest of the chapter. The mathematical expression of N(y, j, c) is complex but, fortunately, it can be simplified for systems displaying some symmetry. Two levels of symmetry have to be considered. The first is relative to the statistical distribution of structural units’ orientation. For example, if the distribution is centrosymmetric, all the u‘mn coefficients are equal to 0 for odd ‘ values. Since this is almost always the case, only u‘mn coefficients with even ‘ will be considered herein. In addition, if the (X, Y), (Y, Z), and (X, Z) planes are all statistical symmetry elements, m should also be even otherwise u‘mn ¼ 0 [1]. In this chapter, biaxial and uniaxial statistical symmetries are more specifically considered. The second type of symmetry is inherent to the structural unit itself. For example, the structural units may have an orthorhombic symmetry (point group symmetry D2) which requires that n is even otherwise u‘mn ¼ 0 [1]. In this theoretical section, we will detail the equations of orientation for structural units that exhibit a cylindrical symmetry (cigar-like or rod-like), i.e., with no preferred orientation around the Oz-axis. In this case, the ODF is independent of c, leading to n ¼ 0. More complex cases have been treated elsewhere [1,4]
2.2 Biaxial distribution As seen above, the angle c takes random values (n ¼ 0) for structural units with cylindrical symmetry. The ODF is then defined by two angles and reduces to the following expansion in surface spherical harmonics 1 X ‘ 1 X 2‘ þ 1 ð‘ mÞ! hP‘m iP‘m ðx ¼ cos yÞ cos mj; with ‘ even (7) Nðy; jÞ ¼ 2p ‘¼0 m¼‘ 2 ð‘ þ mÞ! P‘m ðx ¼ cos yÞ ¼ P‘m0 ðx ¼ cos yÞ are the associated Legendre polynomials and are given by the following expression [5] dm (8) P‘m ðx ¼ cos yÞ ¼ ð1 x2 Þm=2 m P‘ ðxÞ dx
300
Thierry Lefe`vre et al.
where the functions P‘ ðxÞ are the Legendre polynomials and are given, after the Rodrigue`s formula, by ‘ 1 d‘ 2 P‘ ðxÞ ¼ P‘0 ðxÞ ¼ ‘ x 1 (9) ‘ 2 ‘! dx and Z p Z 2p hP‘m i ¼ Nðy; jÞP‘m ðcos yÞ sin ydydj (10) y¼0
j¼0
2.3 Uniaxial distribution In this case, the ODF is independent of j and c and simplifies into the following expansion in Legendre polynomials 1 X 2‘ þ 1 hP‘00 iP‘ ðcos yÞ; for ‘ even (11) NðyÞ ¼ 2 ‘¼0 Z
p
with hP‘00 i ¼ hP‘0 i ¼ hP‘ i ¼
NðyÞ P‘ ðcos yÞ sin ydy
(12)
0
The expressions of the first few non-normalized Legendre polynomials are given below hP000 i ¼ hP00 i ¼ hP0 i ¼ 1 1 3cos2 y 1 2
(14)
1 35cos4 y 30cos2 y þ 3 8
(15)
hP200 i ¼ hP20 i ¼ hP2 i ¼ hP400 i ¼ hP40 i ¼ hP4 i ¼
1 1 cos2 y cos 2f 4
(16)
1 7cos4 y þ 8cos2 y 1 cos 2f 24
(17)
1 4 cos y 2cos2 y þ 1 cos 4f 16
(18)
hP220 i ¼ hP22 i ¼ hP420 i ¼ hP42 i ¼
(13)
hP440 i ¼ hP44 i ¼
2.4 Relationships between the order parameters and the shape of the ODF The complete determination of the ODF requires the knowledge of all the hP‘m i coefficients. For each characterization technique, the measurable quantities that represent molecular orientation can be expressed as a function of a different number of order parameters. All techniques allow at least the measurement
Characterization of Molecular Orientation
301
of hP2 i. Birefringence and IR spectroscopy, two techniques that are commonly used and relatively straightforward to implement (Sections 3 and 4), give access to hP2 i only. The boundary limits of hP2 i are 0:5 hP2 i 1 and the interpretation of the molecular orientation for the limiting hP2 i values in uniaxial systems is hP2 i ¼ 0:5 ) perfect orientation perpendicular with respect to the symmetry axis (OZ), hP2 i ¼ 0 ) isotropic system or perfect orientation at 54.71, and hP2 i ¼ 1 ) perfect orientation along the symmetry axis (OZ). For the ideal case where all the structural units have an identical orientational direction (i.e., a Dirac distribution), the angle of molecular orientation y0 can be calculated from the value of hP2 i by rffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi 2 hP 2 i þ 1 y0 ¼ arcos (19) 3 One should be aware of the fact that orientation distributions with different shapes and/or widths can result in an identical hP2 i value. Determination of higher-order terms (hP4 i, hP6 i, etc.) of the ODF allows for distinguishing between these different possibilities [6]. Polarized Raman and fluorescence spectroscopies, NMR and X-ray diffraction allow the determination of at least hP2 i and hP4 i for uniaxial systems. This is a great advantage since the shape of the orientation distribution can then be estimated [7], even if not all the coefficients of the ODF’s expansion are known. While hP2 i has fixed boundary limits, those of hP4 i depend on the hP2 i value such as 3 35hP2 i2 10hP2 i 7 5 hP 2 i þ 7 hP4 imin ¼ hP4 i hP4 imax ¼ 1 (20) 7 18 12 The limiting values of hP4 i are plotted as a function of hP2 i in Figure 2. For hP4 i ¼ hP2 i ¼ 0, the distribution is isotropic. If hP4 i ¼ hP4 imin , the ODF corresponds to a unimodal and infinitely narrow distribution centered at the angle y0 as given in Equation (19). If hP4 i ¼ hP4 imax , the distribution is infinitely narrow, bimodal, and centered at 0 and 901 with respect to the OZ-axis. Moreover, for certain values of hP4 i, the ODF is purely Gaussian (Figure 2) [8]. Finally, for intermediate values of hP4 i, the unimodal, bimodal, or Gaussian character of the ODF may be more or less pronounced.
3. BIREFRINGENCE Birefringence is one of the simplest methods for the characterization of molecular orientation in polymers. The polarizability of a structural unit is usually not equivalent in all directions, leading to three independent refractive indices along its principal axes. In an isotropic sample, a single averaged macroscopic refractive index is observed whereas birefringence or trirefringence is observed
302
Thierry Lefe`vre et al.
1.0
< P4 >min (unimodal, infinitely narrow) < P4 >max (bimodal, infinitely narrow) < P4 > (unimodal, Gaussian)
0.5 < P4 >
3/8
0.0
Isotropic
1/7 -0.5
0
0.5
1
-3/7
-0.5
< P2 >
Figure 2 Maximum and minimum values of hP4 i as a function of hP2 i and (hP2 i,hP4 i) curve for a Gaussian ODF.
if preferential orientation exists. Three birefringence indices, Dnij (i, j ¼ X, Y, or Z), can be calculated by measuring the refractive index, n, along the machine (Z), transverse (X), and normal (Y) directions: DnZY ¼ nZ nY ;
DnZX ¼ nZ nX ;
DnYX ¼ nY nX
(21)
Only two birefringence indices are independent and necessary to describe the anisotropy of a biaxial system, while a single birefringence measurement is required for uniaxial samples because nX ¼ nY. Birefringence allows the determination of the second moment of the ODF with respect to a given axis as: Dn (22) Dn Dn1 is the intrinsic birefringence that would be observed if all chains were oriented along the reference axis. The magnitude and sign of Dn1 depend on the nature and physical state (crystalline or amorphous) of the polymer. It can be calculated from the polarizabilities using the Lorentz–Lorentz equation or from orientation values determined using an independent technique [3]. In addition to ‘‘orientation’’ birefringence, ‘‘form’’ birefringence due to the presence of anisotropic structures that possess a different refractive index can appear in multiphase polymer systems, including semicrystalline polymers. Its effect is generally neglected but it can be determined to obtain more accurate results [9]. The main limitation of birefringence is that it only provides an averaged orientation value without any discrimination between amorphous and crystalline phases, or between the components in polymer blends, copolymers, and hP 2 i ¼
Characterization of Molecular Orientation
303
composites. Its experimental simplicity and its potential for time-resolved and imaging studies nevertheless make it the most widely used technique to study orientation in polymers. Only the most common experimental approaches to measure birefringence will be described.
3.1 Refractometry method Refractometry consists in the direct measurement of the three refractive indices (or only two in the case of uniaxial orientation) of the sample using a refractometer equipped with a polarizer [10]. Measurement along the ND can be challenging, especially for thin films. Tassin et al. have used this approach to study the orientation in films of poly(ethylene terephthalate) (PET) deformed under planar uniaxial conditions [11]. Figure 3 shows that, as stress is applied, the normal to the phenyl rings develops a negative orientation function with respect to the MD (expressed here as X1) because, as expected, the main chain of the polymer orients along the stretching axis. The orientation function is larger along the ND (X3) than the TD (X2), showing that orientation is not uniaxial with the phenyl groups being found preferentially parallel to the plane of the film.
3.2 Compensation method The compensation method is based on the phenomenon of optical retardation. The sample is placed between crossed polarizers set at 451 and +451 to the main axis, respectively. Because of the refractive index difference, the incident radiation will propagate at different speeds along the ordinary and extraordinary axes. The optical retardation, R, between the two components in the emerging beam is given by R ¼ dDn=l, where d is the thickness of the sample and l is the wavelength of the radiation. The sign and magnitude of R, and thus those of Dn and of hP2 i, can be determined by using many types of commercially available
Figure 3 Orientation of the phenyl rings in stretched PET films, with respect to the machine (X1), transverse (X2), and normal (X3) directions, as a function of applied stress, s0, at 901C. Birefringence results were obtained using refractrometry. Reproduced with permission from Lapersonne et al. [11]. Copyright Elsevier 1994.
304
Thierry Lefe`vre et al.
compensators. In the case of biaxial orientation, DnZY must be determined in addition to DnZX by tilting the sample around the Z-axis. The compensation method is highly sensitive and can detect birefringence as weak as 106 [12]. For instance, Abtal et al. have used a Babinet–Soleil compensator to study the overall orientation in blends of polystyrene (PS) and poly(vinyl methyl ether) (PVME) deformed above room temperature [13]. They observed similar behavior for birefringence and Young’s modulus during stretching, in agreement with the stress-optical rule. The compensation birefringence measurement is very easily coupled to optical microscopy in the transmission and reflection modes, thus allowing characterizing orientation with a spatial resolution of a few hundreds of nanometers [14]. Polarizing microscopes are widely available and are often used for birefringence studies even if spatial resolution is not required. Objectives specifically designed for cross-polarized microscopy are necessary to avoid artifacts.
3.3 Transmission method This technique is also based on the phenomenon of optical retardation. The transmission, T, of light transmitted through crossed polarizers depends on the birefringence of the sample as: d (23) T sin2 ðp RÞ ¼ sin2 p Dn l Such measurement provides the magnitude of birefringence, but not its sign. In addition, identical transmission values will be observed for multiple birefringence orders, that is, whenever the optical path difference, dDn, becomes a multiple of l. The main interest of this method arises from its excellent time resolution, below 1 ms, that is readily achieved using a low-power (e.g., 5 mW) continuous-wave laser and a photodiode. If the sample is initially isotropic, it is possible to follow the birefringence order to obtain quantitative results. For improved accuracy, a second (reference) photodiode or a beam chopper and a lock-in amplifier can be used. This technique has been employed to study the mechanical deformation of polymers [15,16] and the photo-induced orientation of azopolymers [17]. For instance, Messe´ et al. have followed in real time the deformation and relaxation of PS at different temperatures above its glass transition temperature (Tg) [15]. Figure 4 shows that hP2 i increases almost linearly during deformation but that lower values are obtained at higher temperatures, due to segmental relaxation during stretching. When deformation is stopped, orientation first decreases rapidly, with a characteristic relaxation time ranging from 13 s at Tg+51C to as little as 1 s at Tg + 201C, and then slowly decreases toward the isotropic state at long times. A method derived from the transmission technique, spectrographic birefringence, overcomes the problem of multiple birefringence orders [18]. It can be noted from Equation (23) that the transmission minima and maxima occur at a
Characterization of Molecular Orientation
305
0.10
< P2 ( cosθ ) >Δn
0.08
0.06
0.04 Tg +5°C 0.02
Tg +10°C Tg +15°C Tg +25°C
0.00 0
100
200
300 time (s)
400
500
600
Figure 4 Evolution of the orientation during and after the deformation of PS films at different temperatures above Tg. Time-resolved birefringence results with up to a 2 ms time resolution were obtained using the transmission method. Reproduced with permission from Messe´ et al. [15]. Copyright Elsevier 2001.
different Dn value for different l. By replacing the laser by a broadband source and the photodiode by a spectrograph, it is thus possible to determine quantitatively the orientation of a sample without a priori knowledge of its birefringence order. A further development of the transmission technique for the study of biaxial systems consists in probing the sample at normal and tilted incidence simultaneously, allowing real-time characterization of both the inplane (DnZX) and out-of-plane (DnZY) birefringences. Ajji et al. have coupled this multiple incidence approach with spectrographic birefringence to study blown films and bottles, and biaxially tentered thick sheets [19].
4. INFRARED LINEAR DICHROISM (IRLD) IR spectroscopy is a powerful and readily available orientation characterization technique. It offers a high chemical selectivity since most functional groups absorb at distinct wavelengths (typically in the 2.5–25 mm range (4,000–400 cm1 range)), which often depend on their local environment. IR spectroscopy thus provides qualitative and quantitative information about the chemical nature of a sample, its structure, interactions, etc. The potential of IR spectroscopy for orientation characterization stems from the fact that absorption only occurs if the electric field vector of the incident radiation, E, has a component parallel to the transition dipole moment, M, of the absorbing entity. The absorbance, A, is given
306
Thierry Lefe`vre et al.
by A / ðM EÞ2 ¼ M2 E2 cos2 g, where g is the angle between the transition dipole moment and the electric field vectors. The absorbance of an isotropic sample is thus independent of the polarization state, while an oriented sample preferentially absorbs radiation when g ¼ 01. In many cases, it is more interesting to describe the orientation of the polymer chain (the Oz-axis of Figure 1) with respect to the sample coordinate system rather than that of a specific chemical group. This is possible if the transition dipole moment of the measured band is at a fixed angle, b, with respect to the main chain of the polymer (i.e., the Oz-axis) and presents a cylindrical symmetry, that is, has no preferential orientation around the c angle. In this case, the Legendre addition theorem allows calculating the order parameters of the main chain, from the experimentally determined parameters for the transition dipole moment as hP2 ðcos yÞi ¼
hP2 ðcos gÞi ; P2 ðcos bÞ
where P2 ðcos bÞ ¼
3cos2 b 1 2
(24)
Because of the cos2g dependency, IR linear dichroism (IRLD) only provides the second moment of the ODF. It is often sufficient to describe the uniaxial and biaxial orientation in polymeric systems. However, the knowledge of hP2 i values alone does not allow discriminating between systems when its value becomes very close to unity, as illustrated below (see discussion on page 330 related to Figure 17). In addition, it does not provide information about the shape and the width of the ODF: one must assume a unimodal distribution, despite the fact that multiple ODFs can yield the same hP2 i value [6]. These limitations are nevertheless well compensated by the simplicity and availability of the technique, and by its selectivity that often allows the simultaneous measurement of the orientation of the different components in blends and copolymers, phases in semicrystalline systems, main chain vs. side-chain groups, etc. It should be noted that the cos2g absorption rule also applies to spectroscopies in the X-ray, ultraviolet (UV), visible, near-IR, and far-IR (terahertz) ranges, but those are less often used because of their more limited selectivity or strong overlap of bands. Exceptions are the frequent use of visible LD for the characterization of photo-oriented azopolymers [20], and that of near-IRLD for the study of millimeters thick polymer films [21]. Polarized IR spectra can be recorded using several sampling modes, depending on the coveted information and nature of the sample. Transmission IRLD is the most straightforward and common approach but its utility is limited to relatively thin films. In contrast, reflection techniques allow for studying thick or irregularly shaped samples and provide surface specific measurements, but are more complex and susceptible to artifacts. Polarized IR emission and photoacoustic spectra can also be measured but are seldom used, and will not be described here. A wire-grid polarizer is normally used to polarize the IR radiation. A typical degree of polarization value is 99.5% at 1,000 cm1, but it often decreases to less than 99% or 96% at 3,000 cm1 for holographic and mechanically grooved polarizers, respectively. These specifications can vary significantly between suppliers, in spite of similar groove densities and fabrication methods. The error on the orientation function is thus larger at higher frequencies due to polarization leakage.
Characterization of Molecular Orientation
307
4.1 Transmission IRLD 4.1.1 Normal incidence Normal incidence transmission IRLD measurements are used to study thin films (typically 100 mm thickness and less, depending on the molar extinction coefficient of the bands) with in-plane uniaxial orientation. Two spectra are recorded sequentially with the radiation polarized parallel (p) and perpendicular (s) to the principal (machine) direction of the sample. The order parameter of the transition moment of the studied vibration is calculated from either the dichroic ratio (R ¼ Ap/As) or the dichroic difference (DA ¼ ApAs) as: hP2 ðcos gÞi ¼
R 1 DA ¼ R þ 2 3A0
(25)
Ap and As are the absorbances measured with p- and s-polarization, respectively, and A0 ¼ Ap þ 2As =3 is the structural absorbance spectrum that would be measured for an isotropic sample. The order parameter of the main chain can be determined using the Legendre addition theorem (Equation (24)). In a classic series of articles, Monnerie and coworkers have used IRLD to study the effect of deformation on the orientation of a series of polymers and polymer blends [22,23]. For example, Figure 5 shows the p- and s-polarized
Figure 5 Polarized infrared spectra (s on top, p on bottom) recorded for an oriented 80/20 PS/PPO miscible blend using normal incidence transmission. Reproduced with permission from Lefebvre et al. [23]. Copyright Elsevier 1981.
308
Thierry Lefe`vre et al.
spectra recorded for a blend containing 80% of PS and 20% of poly(2,6-dimethyl1,4-phenylene oxide) (PPO) [23]. Because of IR selectivity, the orientation of both components could be followed independently. The 906 cm1 band, due to out-ofplane deformation of the phenyl groups, was used to quantify the orientation of PS. It shows parallel dichroism, as expected from its reported 351 b angle. In contrast, the PPO out-of-plane benzene mode at 865 cm1 shows negative dichroism because its transition dipole moment makes a 741 angle with the main chain. Deformation studies revealed that the hP2 i values for PS more than doubled with increasing PPO content from 0 to 25%. In contrast, the orientation of the higher-Tg PPO was not affected by composition over this range and was always larger than that of PS. Normal transmission IRLD can also be used to characterize polymeric fibers, although scattering can induce sloping baselines. Raman spectroscopy then becomes a convenient alternative. Rutledge et al. have recently probed the orientation in electrospun nanofibers composed of a core of Bombyx mori fibroin and an outer shell of poly(ethylene oxide) [24]. The orientation values were low, less than 0.1, as is often the case in electrospun fibers. Microscopic IRLD measurements can also be performed, either with a single element detector or with a focal plane array for direct imaging, providing a spatial resolution of a few to a few tens of micrometers. Specially designed objectives allow performing microscopy studies using the reflection techniques described below. Chalmers and Everall have presented several examples of the use of single detector IR microscopy to characterize industrial samples under various sampling modes [25], while Mendelsohn et al. have used polarized IR imaging to assess the orientation of collagen fibrils in different sections of articular cartilage [26]. While calculating the orientation function is the goal of several analyses, the presence of orientation in a sample can sometimes obscure other useful structural information obtainable by IR spectroscopy. For instance, the trans/gauche ratio of PET can be determined using conformationally sensitive bands, but the presence of molecular orientation makes direct determination impossible even with unpolarized light. In such cases, calculating the structural absorbance spectrum, A0, allows for extracting structural information from the spectra without any interference from orientation [27]. It should also be mentioned that, in several cases, it is not possible or even necessary to calculate the orientation function. It may often be sufficient to simply compare dichroic ratios, for instance, when comparing a series of samples from an industrial process. In other cases, the angle b is not known and the calculation of a hP2 ðcos gÞi may not yield more information. For instance, Bazuin and Fan used dichroic ratios to follow the development of orientation as a function of draw ratio for poly(ethyl acrylate) in ionically complexed blends of copolymers [28].
4.1.2 Tilted incidence Normal incidence measurements are sufficient for uniaxially oriented samples, but a third spectrum along the ND (Y) is necessary to describe the orientation in biaxially oriented samples or in the case of uniaxial anisotropy in the thickness
Characterization of Molecular Orientation
309
of the film. This additional spectrum is also necessary to calculate the orientationindependent structural absorbance spectrum, which is given by A0 ¼ ðAZ þ AY þ AX Þ=3 for biaxially oriented samples. A tilted incidence transmission measurement can be performed to obtain the AY spectrum. The polarizer is set parallel to the Z-axis and the sample is rotated by an angle a around the X-axis. AY, is given by: 1=2 sin2 a Aa 1 2 AZ n AY ¼ þ AZ (26) sin2 a n2 Aa is the absorbance in the tilted geometry, AZ the absorbance measured in normal incidence geometry with light polarized along the Z-axis, and n the refractive index of the sample. The isotropic refractive index in the visible range is often used as a first approximation, but quantitative measurements require knowledge of the anisotropic refractive indices at the wavelength of interest [29]. The orientation along the different axes can be quantified using a series of orientation coefficients, fj: fj ¼
Aj =A0 1 ð3cos2 b 1Þ
(27)
where Aj is the absorbance along the j direction. For a system with uniaxial orientation and cylindrical symmetry, fZ simplifies to the usual hP2 i coefficient. Ajji et al. have used this technique and formalism to characterize the biaxial orientation in blown films of polypropylene/linear low-density polyethylene (PP/LLDPE) multilayers and blends [30]. The chemical specificity of IRLD allowed for independently determining the orientation coefficient of the c-axis of PP, as well as that of the a- and b-axes of the crystalline phase of PE. Tilted incidence IRLD was also used to probe biaxial orientation in films of polyamide-6 deformed under different conditions [31]. Structural absorbance spectra were also calculated to probe the amount of the different crystalline forms, in addition to their orientation.
4.2 Reflection IRLD 4.2.1 Attenuated total reflection (ATR) ATR is one of the most useful and versatile sampling modes in IR spectroscopy. When radiation is internally reflected at the interface between a high-refractive index ATR crystal (usually Ge, ZnSe, Si, or diamond) and the sample, an evanescent wave penetrates inside the sample to a depth that depends on the wavelength, the refractive indices, and the incidence angle. Because the penetration depth is typically less than 2 mm, ATR provides surface specific information, which can be seen as an advantage or not if surface orientation differs from that of the bulk. It also allows one to study thick samples without preparation and can be used to characterize highly absorbing bands that are saturated in transmission measurements.
310
Thierry Lefe`vre et al.
Four polarized ATR spectra can be recorded to characterize the threedimensional (3D) orientation of a sample. p- and s-polarized spectra are recorded with the sample clamped with its Z- and X-axes sequentially aligned perpendicular to the incidence plane (that is, parallel to the s-polarized electric field). The absorbance measured in these different configurations is related to the anisotropic absorption indices of the sample, kj, as As;Z ¼ K1 kZ ;
As;X ¼ K1 kX ;
Ap;Z ¼ K2 kX þ K3 kY ;
Ap;X ¼ K2 kZ þ K3 kY (28)
The parameters K1, K2, and K3 are defined by the refractive indices of the crystal and sample and by the incidence angle [32]. If the sample has uniaxial symmetry, only two polarized spectra are necessary to characterize the orientation. If the optical axis is along the plane of the sample, such as for stretched polymer films, only the two s-polarized spectra are needed to determine kZ and kX. These are then used to calculate a dichroic ratio or a hP2 i value with Equation (25) (replacing absorbance with absorption index). In contrast, a uniaxial sample with its optical axis perpendicular to the crystal surface requires the acquisition of spectra with both p- and s-polarizations, but the Z- and X-axes are now equivalent. This approach was used, through dichroic ratio measurements, to monitor the orientation of polymer chains at various depths during the drying of latex [33]. This type of symmetry is often encountered in non-polymeric samples, for instance, in ultrathin films of lipids or self-assembled monolayers. In contrast to the above cases, the spectra in the four geometries are necessary for samples showing biaxial orientation. The information along the ND is accessible because under p-polarization, the electric field has components both in-plane (Z or X) and out-of-plane (Y) with respect to the sample. Although the details are beyond the scope of this chapter, Everall and Bibby have shown how to determine directly the different hP2mn i values (m, n ¼ 0 or 2) by measuring the four absorbances of Equation (28) for two bands with different b angles [32]. It is important to stress that ATR absorbance is strongly affected by the sample/crystal contact. Quantitative results are thus difficult to obtain even if the contact is maintained during the sample rotation that is required to record all four polarized spectra. A reference band that does not show significant dichroism is thus most often used to normalize the polarized absorbances in order to obtain quantitative data. For instance, the 1,410 cm1 band of PET has often been chosen for that purpose, not only for ATR studies but also for specular reflectance (see below) and even transmission studies when the sample thickness is not uniform. It was shown that an appropriate normalization is possible even if no such reference band is available, by using a combination of two bands with orthogonal dichroism [34]. When performing ATR experiments, one should also make certain that the applied pressure does not create artifacts by affecting the structure of the sample. As an example, Cooper and coworkers have used polarized ATR spectroscopy to characterize the surface orientation of PET bottles [35]. They first confirmed the quantitative agreement between ATR and X-ray diffraction results, and then studied the molecular orientation of the bottles at 2 cm intervals.
Characterization of Molecular Orientation
311
Figure 6 Chain orientation along the hoop, length, and thickness directions measured at different positions along the length of a standard PET bottle. Polarized ATR spectra were recorded for (a) the outer and (b) the inner surfaces of the bottle, respectively. Reproduced with permission from Smith et al. [35]. Copyright Elsevier 2006.
Figure 6 shows the biaxial orientation of PET on the inner and outer surfaces of the bottle, expressed in terms of the average squared cosine angles between the main chain of PET and the hoop, the length, and the thickness directions, respectively. These values are proportional to the orientation coefficients of Equation (27). Very small values are found in the thickness direction, indicating that the chains are almost exclusively in the plane of the bottle. The in-plane orientation varies significantly along the length of the bottle: for both surfaces, the chains are preferentially oriented along the length in the neck region and along the hoop closer to the base of the bottle, but the behavior at intermediate positions is quite different for the inner and outer surfaces. This information would have been lost with transmission measurements across the full bottle thickness.
4.2.2 Specular reflectance As for ATR, specular (front surface) reflection provides surface orientation and can be used to study thick samples or highly absorbing bands. In addition, because it is a non-contact technique, it enables the study of samples that cannot be held in close contact with an ATR crystal or that would be affected by pressure. In specular reflection, the polarized radiation is incident at an angle close to the normal, often 10–201, and only the light reflected at the front surface of the sample should be detected. This precludes the study of highly scattering samples and requires that the sample is ‘‘optically thick’’, meaning that it must be thick enough or that the bands are intense enough so that no light gets reflected from the second surface. In contrast with other methods, spectra recorded by specular reflection show dispersion-like shaped bands because both the refractive index (n) and the absorption index (k) contribute to reflection. These can nevertheless be separated
312
Thierry Lefe`vre et al.
by performing a Kramers–Kro¨nig transformation on the raw data using a processing tool implemented in most spectroscopy softwares [36]. The k values thus obtained are proportional to absorbance and can be used to calculate dichroic ratios and orientation coefficients using the procedures described in the previous sections. In some cases, surface imperfections and differences in polarized reflectivity can yield different k values for p- and s-polarized spectra even for an isotropic sample. The use of a reference normalization band is thus frequent. Specular reflection IR spectroscopy has been used by Cole and coworkers to study the orientation and structure in PET films [36,37]. It has allowed characterizing directly very highly absorbing bands in thick samples, in particular the carbonyl band that can show saturation in transmission spectra for thickness as low as 2 mm. The orientation of different conformers could be determined independently. Specular reflection is normally limited to uniaxial samples because the near-normal incident light does not allow measuring AY. However, it was shown that the orientation parameter along the ND can be indirectly determined for PET by using the ratio of specifically selected bands [38]. This approach was applied to the study of biaxially oriented PET bottles [39].
4.3 Time-resolved IRLD An interesting feature of polarized IR spectroscopy is that rapid measurements can be performed while preserving molecular information (in contrast with birefringence) and without the need for a synchrotron source (X-ray diffraction). Time-resolved IRLD studies are almost exclusively realized in transmission because of its compatibility with various types of tensile testing devices. In the simplest implementation, p- and s-polarized spectra are sequentially acquired while the sample is deformed and/or relaxing. The time resolution is generally limited to several seconds per spectrum by the acquisition time of two spectra and by the speed at which the polarizer can be rotated. Siesler et al. have used such a rheo-optical technique to study the dynamics of multiple polymers and copolymers [40]. A more complex but faster and more sensitive approach is polarization modulation (PM) IRLD. For such experiments, a photoelastic modulator is used to modulate the polarization state of the incident radiation at about 100 kHz. The detected signal is the sum of the low-frequency intensity modulation with a highfrequency modulation that depends on the orientation of the sample. After appropriate signal filtering, demodulation, and calibration [41], a dichroic difference spectrum can be directly obtained in a single scan. This improves the time resolution to B400 ms, prevents artifacts due to relaxation between measurements, and improves sensitivity for weakly oriented samples. However, structural information can be lost since individual polarized spectra are not recorded. Pe´zolet and coworkers have used this approach to study the deformation and relaxation in various homopolymers, copolymers, and polymer blends [15,42,43]. For instance, Figure 7 shows the relaxation curves determined in situ for miscible blends of PS and PVME [42]. The hP2 i values were determined
Characterization of Molecular Orientation
313
Figure 7 Relaxation of orientation measured simultaneously for both components in miscible PS/PVME blends following a rapid deformation (1 m/s) to a draw ratio of 2 at Tg +151C. The time-resolved dichroic difference spectra were acquired using PM-IRLD. Reproduced with permission from Pellerin et al. [42]. Copyright 2000 American Chemical Society.
simultaneously using component specific C–H stretching bands. Larger orientations and slower relaxation rates were observed for PS as compared to PVME for all compositions. Nevertheless, the relaxation of both components was hindered by the addition of faster relaxing PVME, which was interpreted by the presence of nanoheterogeneities. Finally, an ultra-rapid-scanning FTIR spectrometer, which uses a continuously rotating wedged disk mirror rather than a standard reciprocating mirror, provides the fastest time resolution for polarized IR spectroscopy, but is limited to measurements with a single polarization. The cold drawing of PET was followed with a 10 ms time resolution, showing rapid gauche-to-trans conformational change and the development of very large trans conformers orientation upon necking [27].
5. RAMAN SPECTROSCOPY AND MICROSPECTROSCOPY Raman spectroscopy is an inelastic light scattering experiment for which the intensity depends on the amplitude of the polarizability variation associated with the molecular vibration under consideration. The polarizability variation is represented by a second-rank tensor, axyz , the Raman tensor. Information about orientation arises because the intensity of the scattered light depends on the orientation of the Raman tensor with respect to the polarization directions of the electric fields of the incident and scattered light. Like IR spectroscopy, Raman
314
Thierry Lefe`vre et al.
spectroscopy can provide qualitative and quantitative information relative to several chemical groups located in different parts of the macromolecules and that are often sensitive to molecular conformation, local environment, interactions, etc. The Raman tensor can be expressed in the coordinate system Oxyz of the molecule (Figure 1) with its principal components a1 , a2 , and a3 such as 0 1 0 1 a1 0 0 a1 0 0 B C B C axyz ¼ @ 0 a2 0 A ¼ a3 @ 0 a2 0 A; with a1 ¼ a1 =a3 and a2 ¼ a2 =a3 (29) 0 0 a3 0 0 1 For orientation measurements, this tensor also needs to be expressed in the ~ coordinate system OXYZ, aXYZ , using the matrix transformation axyz ¼ FaXYZ F, where F is a matrix whose elements are the direction cosines of the coordinate ~ is its transposed matrix [44]. axes and F
5.1 Conventional Raman spectroscopy (macro-Raman) The theory of orientation measurements by linearly polarized Raman spectroscopy has been developed in detail by Bower in 1972 [44]. The Raman intensity, I, is given by * + X 2 0 I ¼ I0 ‘i ‘j aij ; with i; j ¼ X; Y; or Z (30) i;j
‘i0 and ‘j are the direction cosines of the incident and scattered electric fields, respectively, I0 is a constant that depends on the number of scattering units, instrumental factors, and laser intensity, and the brackets indicate a mean value calculated over the distribution of orientation. In Equation (30), different quadratic quantities ha2ij i or haij apq i can be considered. They are related to the second and fourth moments of the ODF expansion. In particular, for uniaxial systems, knowledge of hP4 i indeed gives information about the shape of the distribution of orientation [7] and, moreover, allows the calculation of the most probable ODF using the information theory [45].
5.1.1 Uniaxial systems For a uniaxial sample, there are five independent quantities haij apq i or ha2ij i given by [44] I 0 a2XX ¼ I 0 a23 ½ 3a21 þ 3a22 þ 3 þ 2a1 a2 þ 2a1 þ 2a2 =15 þ P2 3a21 þ 3a22 þ 6 þ 2a1 a2 a1 a2 =21 þ 3P4 3a21 þ 3a22 þ 8 þ 2a1 a2 8a1 8a2 =280 I 0 a2ZZ ¼ I 0 a23 ½ 3a21 þ 3a22 þ 3 þ 2a1 a2 þ 2a1 þ 2a2 =15 þ 2P2 3a21 þ 3a22 6 þ 2a1 a2 a1 a2 =21 þ P4 3a21 þ 3a22 þ 8 þ 2a1 a2 8a1 8a2 =35
Characterization of Molecular Orientation
I 0 a2XY ¼ I 0 a23 ½ a21 þ a22 þ 1 a1 a2 a1 a2 =15 þ P2 a21 þ a22 2 4a1 a2 þ 2a1 þ 2a2 =21 þ P4 3a21 þ 3a22 þ 8 þ 2a1 a2 8a1 8a2 =280 I 0 a2ZX ¼ I 0 a23 ½ a21 þ a22 þ 1 a1 a2 a1 a2 =15 þ P2 a21 þ a22 2 4a1 a2 þ 2a1 þ 2a2 =42 þ P4 3a21 þ 3a22 þ 8 þ 2a1 a2 8a1 8a2 =70 I 0 haXX aZZ i ¼ I 0 a23 ½ a21 þ a22 þ 1 þ 4a1 a2 þ 4a1 þ 4a2 =15 þ P2 a21 þ a22 2 þ 10a1 a2 5a1 5a2 =42 þ P4 3a21 þ 3a22 þ 8 þ 2a1 a2 8a1 8a2 =70
315
ð31Þ
They represent a system of five equations with five unknowns, namely a1, a2, hP2 i, hP4 i, and I 0 a23 . Its complete resolution is the most general method to determine the molecular orientation of samples with uniaxial symmetry (referred to as the ‘‘general’’ method hereafter). As opposed to other methods (see below), it requires no assumption about the shape of the Raman tensor. Equations (31) have first been solved for oriented poly(methyl methacrylate) (PMMA) [46]. The method has later been extended by Pigeon et al. [47] to obtain the relevant spectra of Equation (31) using the backscattering and right-angle geometries. The ‘‘general’’ method is relatively complex from both mathematical and experimental viewpoints and requires the choice of initial conditions that are unfortunately not unique. Despite these difficulties, it has been successfully applied to quantify the orientation of various polymers. As an example, Figure 8 shows the five independent polarized spectra corresponding to Equation (31) for PE roll-drawn to a draw ratio of 11.7 [47]. The differences in the relative band intensities with polarization illustrate the strong orientation of the molecules. The band at 1,130 cm1 measured in the I 0 a2XX spectrum (Figure 8) is assigned to the symmetric stretching mode of the C–C bonds and has been specifically used to determine the order parameters hP2 i and hP4 i for various draw ratios. The relative intensity of the 1,060 cm1 band (antisymmetric C–C stretching mode) with respect to that at 1,130 cm1 as a function of hP2 i and hP4 i is plotted in Figure 9. Such a calibration curve shows that some intensity ratios can be a good probe to estimate the orientation level of macromolecules. The method described by Pigeon et al. has been used to investigate PE foils [48], PET fibers [49] and films [50], and uniaxially oriented liquid-crystalline films of polyesters [51]. An approach simpler than the ‘‘general’’ method has been used by Bower and coworkers [52,53] and has proved to be useful to determine the order parameters of uniaxially oriented polymers. This approach, called ‘‘cylindrical’’ method, requires a smaller number of spectra that are easily measurable, but it assumes that the Raman tensor associated with the vibrational mode under study is cylindrical. In such case, a1 ¼ a2 ¼ a so that the depolarization ratio Riso of an
316
Thierry Lefe`vre et al.
Figure 8 Five independent spectra of a uniaxially stretched PE sample (draw ratio of 11.7). Reproduced with permission from Pigeon et al. [47]. Copyright 1991 American Chemical Society.
isotropic sample is given by ha2ij i ð1 aÞ2 Riso ¼ 2 ¼ ; iaj; with i; j ¼ X or Z 2 ð8a þ 4a þ 3Þ aii
(32)
Consequently, the measurement of three spectra and the determination of a from the isotropic sample allow calculation of hP2 i and hP4 i. This method has been applied successfully to PET [53] and rubber networks [52], and to study the
Characterization of Molecular Orientation
317
Figure 9 Plot of the intensity ratio h1130/h1060 as a function of hP2 i and hP4 i of PE roll-drawn sheets for various draw ratios. Reproduced with permission from Pigeon et al. [47]. Copyright 1991 American Chemical Society.
photoisomerization of azobenzene polymer matrices [54] and liquid crystal elastomers [55]. Finally, Frisk et al. have proposed a third method, the ‘‘depolarization’’ method, that does not need the assumption of a cylindrical Raman tensor [56]. A randomly oriented sample is again necessary but the depolarization ratio takes the general form 2 2 a1 þ a22 þ 1 a1 a2 a1 a2 Riso ¼ 2 (33) 3a1 þ 3a22 þ 3 þ 2a1 a2 þ 2a1 þ 2a2 The measurement of four independent spectra then leads to the complete resolution of the system, assuming that the depolarization ratio is the same for the oriented and isotropic samples. Frisk et al. have compared the three basic methods on the same poly(propylene terephthalate) (PPT) sample [56]. It appears that the assumption of a cylindrical Raman tensor may be too crude in some cases. Unless the hypothesis of a cylindrical tensor has been ascertained, the two other methods should be used. The ‘‘general’’ method is intrinsically the most accurate one but it
318
Thierry Lefe`vre et al.
suffers from experimental and mathematical complexity. The ‘‘depolarization’’ method is easier to implement but the assumption that the depolarization ratios of the oriented and isotropic samples are identical may not necessarily be true since the local environment may differ. Because the determination of the order parameters by Raman spectroscopy is not straightforward, some works have focused on using intensity ratios to evaluate the molecular orientation (see above). Frisk et al. [56], in particular, have shown that the simple parameter R0 ¼ 1 I XX =I ZZ ¼ 1 a2XX = a2ZZ can efficiently, although qualitatively, characterize orientation in polymers.
5.1.2 Biaxial systems Because of their relative complexity, few Raman studies have dealt with biaxial systems, although valuable structural information can be obtained. Assuming a cylindrical Raman tensor, it has been shown that there are six independent quantities I ij ¼ I 0 ha2ij i given by [3] I XX ¼ I 0 a23 ½A þ BðhP200 i 6hP220 iÞ þ Cð3hP400 i 60hP420 i þ 70hP440 iÞ I YY ¼ I 0 a23 ½A þ BðhP200 i þ 6hP220 iÞ þ Cð3hP400 i þ 60hP420 i þ 70hP440 iÞ I ZZ ¼ I 0 a23 ½A 2BhP200 i þ 8hP220 i I YZ ¼ I 0 a23 ½D EðhP200 i 6hP220 iÞ 4CðhP400 i þ 15hP420 iÞ I YZ ¼ I 0 a23 ½D EðhP200 i þ 6hP220 iÞ 4CðhP400 i 15hP420 iÞ I XY ¼ I 0 a23 ½D þ 2EhP200 i þ CðhP400 i 70hP440 iÞ with
A ¼ 8a2 þ 4a þ 3 =15; D ¼ 8a2 2a þ 1 =15;
B ¼ 8a2 2a 6 =21; E ¼ a2 2a þ 1 =15
ð34Þ C ¼ a2 2a þ 1 =35 ð35Þ
The measurement of these six quantities with the knowledge of a ¼ a1 ¼ a2 leads to the determination of the six unknowns, namely I 0 a23 ; hP200 i; hP220 i; hP400 i; hP420 i; and hP440 i. Application of this method to unidirectionally drawn PET films reveals an orientation of the plane of the aromatic rings in the plane of the film and, surprisingly, a small overall orientation of the chain axes away from the plane of the film [3].
5.1.3 Orientation-insensitive spectra For oriented systems, the determination of molecular conformation is a complex problem because Raman spectra contain signals inherently due to both molecular conformation and orientation. To extract only the information relative to the conformation, one has to calculate a spectrum that is independent of orientation, in a similar way to the A0 structural absorbance of IR spectroscopy (Section 4). Frisk et al. [57] have shown that for a uniaxial sample aligned along the Z-axis, a spectrum independent of orientation (so-called isotropic spectrum), Iiso, can be calculated from the following linear combination of four polarized spectra [57] I iso ð3 þ 6Riso Þ ¼ I zz þ 2I xx þ 4I xz þ 2I xy
(36)
Characterization of Molecular Orientation
319
The method has been successfully applied to PPT samples having different orientation levels. It is noteworthy that the factor (3+6Riso) is not a constant throughout the whole spectral range since Riso is a priori different for each band. This factor is then particularly important if one wants to compare the relative intensities of various vibrational modes. Sourisseau and Talaga [58] have expanded the theoretical expression of orientation-independent intensity sums for systems with biaxial symmetry by making use of the K2 Raman invariant.
5.2 Spectromicroscopy (micro-Raman) The advantage of Raman spectromicroscopy is that very small specimens can be studied while still allowing the determination of the second and fourth moments of the ODF. However, the expressions for the Raman intensities are more complex since the optical effects induced by the microscope objective have to be considered. Although the corrections may be small, they are not necessarily negligible [59]. This problem was first treated by Turrell [59–61] and later by Sourisseau and coworkers [5]. Turrell has mathematically quantified the depolarization of the incident electric field in the focal plane of the objective and the collection efficiency of the scattered light by high numerical aperture objectives. For brevity, only the main results of the calculations will be presented. Readers interested in more details are referred to book chapters and reviews of Turrell or Sourisseau [5,59,61]. The intensity in Raman spectromicroscopy is given by [59–61] Z Z D E ei a ej 2 dV dO I ij ¼ I 0 (37) V
O
where V is volume of scattering units and O is the solid angle of light collection, whereas the unit vectors ei and ej define the directions of the electric fields of the incident laser beam and scattered light, respectively (i, j ¼ X, Y, Z, Figure 1). In spectromicroscopy, the backscattering configuration limits to four the number of different accessible intensities (i, j ¼ X or Z). The four measurable intensities Iij are given by I XX ¼ I 0 ð2C0 þ C2 Þ Aobj a2XX þ Bobj a2XY þ 4C1 Aobj a2YX þ Bobj a2YY þC2 Aobj a2ZX þ Bobj a2ZY I XZ ¼ I 0 ð2C0 þ C2 Þ Aobj a2XZ þ Bobj a2XY þ 4C1 Aobj a2YZ þ Bobj a2YY þC2 Aobj a2ZZ þ Bobj a2ZY I ZX ¼ I 0 ð2C0 þ C2 Þ Aobj a2ZX þ Bobj a2ZY þ 4C1 Aobj a2YX þ Bobj a2YY þC2 Aobj a2XX þ Bobj a2XY I ZZ ¼ I 0 ð2C0 þ C2 Þ Aobj a2ZZ þ Bobj a2ZY þ 4C1 Aobj a2YZ þ Bobj a2YY þC2 Aobj a2XZ þ Bobj a2XY ð38Þ
320
Thierry Lefe`vre et al.
The constants Aobj and Bobj characterize the collection efficiency of the objective and originate from the integration over O. They are related to the numerical aperture NA of the objective so that 4 1 cos ym cos3 ym Aobj ¼ p2 3 3 and Bobj ¼ 2p2
2 1 cos ym þ cos3 ym 3 3
(39)
with ym ¼ arc sin NA=n , n being the refraction index of the sample and ym the effective half-angle of the cone of the light scattered from the sample and collected by the objective. Typically, Aobj ¼ 3.759 and Bobj ¼ 0.737 for n ¼ 1.5 and for a 100 objective (NA ¼ 0.9). The coefficients C0, C1, and C2 represent the depolarization of the light by the objective and arise from the integration over V. They have to be calculated numerically but, since they roughly vary in the ratio 100/10/1, the expressions in Equations (38) can be simplified (see examples below). Based on two intensity ratios, R1 ¼ Izx/Ixx and R2 ¼ Ixz/Izz, and some assumptions, the order parameters can be determined.
5.2.1 Uniaxial systems The quantitative determination of molecular orientation by Raman spectromicroscopy was first applied to azobenzene holographic diffraction gratings [62]. These gratings are optically inscribed by the interference of two coherent laser beams having appropriate polarizations, taking advantage of the photo-induced orientation of the azobenzene moieties that are covalently bonded at side-chain positions of the polymer. This treatment leads to a B0.8–3.0 mm spatial period of the grating that can be suitably analyzed by Raman spectromicroscopy. In these studies, it was assumed that the Raman tensor is cylindrical and that a3 a1 ¼ a2 ða 1Þ. A detailed structural description of the surface relief gratings was obtained thanks to the characterization of molecular orientation. Silk fibers, a basic system with a uniaxial symmetry, have also been investigated by Raman spectromicroscopy [63] that is one of the rare techniques capable of providing molecular data on such small (3–10 mm diameter) single filaments. The amide I band of the silk proteins has been particularly studied to determine the molecular orientation using the cylindrical Raman tensor approximation. In this work, it was assumed that C0 C1 ; C2 and the a parameter was determined from an isotropic sample using the following expression of the depolarization ratio 1 a2 Aobj þ Bobj iso R ¼ (40) ð8a2 þ 4a þ 3Þ Aobj þ ð1 a2 Þ Bobj Figure 10 shows polarized spectra of two types of silks recorded by Raman spectromicroscopy: the dragline silk (the lifeline) of the spider Nephila edulis and the cocoon silk of a wild silkworm Samia cynthia ricini. The position of the amide I band at 1,668–1,669 cm1 for both threads is characteristic of the b-sheet
Characterization of Molecular Orientation
321
Figure 10 Polarized spectra obtained by Raman microspectroscopy of (A) the dragline silk of the spider Nephila edulis and (B) the cocoon silk of the silkworm Samia cynthia ricini. Adapted with permission from Rousseau et al. [63]. Copyright 2004 American Chemical Society.
conformation. Since the IXX spectrum is the most intense, this shows that the carbonyl amide bonds are preferentially oriented perpendicular to the fiber axis, i.e., the b-sheets are basically aligned along the fiber direction. The comparison of the relative intensities of the polarized amide I bands also shows qualitatively that the cocoon silk is the most oriented. This is confirmed by the calculation of the order parameter hP2 i, which is 0.36 for the silkworm’s cocoon and 0.32 for the spider’s dragline.
5.2.2 Biaxial systems The biaxial orientation in photoaddressable azobenzene films has been observed recently by polarized Raman spectromicroscopy [64]. Here, IR spectroscopy has been advantageously used as a complementary technique to measure the order
322
Thierry Lefe`vre et al.
parameters hP200 i associated with five vibrational modes that are also Raman active, in particular the benzene n8a stretching mode at 1,599 cm1. From the measurement of the two intensity ratios R1 and R2, Raman spectromicroscopy has allowed the determination of the remaining unknowns, i.e., the fourthrank coefficients hP400 i, hP420 i, and hP440 i, assuming that C0 C1 ; C2 and that a3 a1 ¼ a2 . These measurements have provided an estimate of the overall distribution of orientation and showed that the chromophores have a preferential orientation in the plane of the films.
5.2.3 Orientation-insensitive spectra Finally, as in macro-Raman experiments, orientation-insensitive spectra can also be calculated for spectromicroscopy. A method has been developed recently for uniaxially oriented systems and successfully tested on high-density PE rods stretched to a draw ratio of 13 and on Bombyx mori cocoon silk fibers [65]. This method has been theoretically expanded to biaxial samples using the K2 Raman invariant and has proved to be useful to determine the molecular conformation in various polymer thin films [58].
6. FLUORESCENCE SPECTROSCOPY Like Raman scattering, fluorescence spectroscopy involves a two-photon process so that it can be used to determine the second and the fourth rank order parameters. In this technique, a chromophore, either covalently linked to the polymer chain or a probe incorporated at small concentrations, absorbs incident light and emits fluorescence. If the incident electric field is linearly polarized in the ei direction and the fluorescent light is collected through an analyzer in the es direction, the fluorescence intensity is given by (41) I ¼ I 0 ðea :ei Þ2 ðee :es Þ2 where ea and ee are the unit vectors of the absorption transition dipole and the fluorescence emission dipole, respectively. I0 depends on the number of fluorescent molecules, incident light intensity, fluorescence quantum yield, and instrumental factors. Information about orientation results from the alignment of the chromophore moieties that absorb and/or emit light in preferential directions. Rewriting Equation (41), we have [44] DX DX 2 E 2 e 2 E I ¼ I0 ‘0i :f ai ‘j :f j ‘0i :‘j :f ai :f ej ¼ I0 ; with i; j ¼ X; Y; or Z (42) i;j
‘i0
i;j
and ‘j are the direction cosines of the incident and emitted electric where fields, respectively, and f ai and f ej are the direction cosines of the absorption and emission axes, respectively. Equation (42) is equivalent to the expression of the Raman intensity (Equation (30)) considering that Fij f ai f ej are the elements a second-rank tensor similar to the Raman tensor a. The method to determine the order parameters [12,44,66] is then comparable to that of Raman spectroscopy, so it will not be developed here.
Characterization of Molecular Orientation
323
Nobbs et al. [67] have performed a detailed fluorescence study of molecular orientation in PET tapes produced by melt spinning and subsequently uniaxially drawn at various temperatures and draw ratios. The instrument configuration was a straight-through geometry and the fluorescent probe was 2,2u(vinylene-dip-phenylene) bisbenzoxazole incorporated at 50–200 ppm. This study has established the usefulness and limitations of the technique, in particular by considering the fact that the absorption and emission axes do not necessarily coincide and by quantifying the effects of birefringence. An example of the determination of order parameters for a uniaxial system is given by Wolarz and Bauman [68] who studied the molecular orientation of a nematic side-chain liquid-crystalline polysiloxane using 4-dimethylamino-4unitrostilbene (DANS) as a guest probe. This polymer undergoes a nematicisotropic phase transition at TNI ¼ 348 K. Figure 11 shows the order parameters hP2 i and hP4 i of DANS as a function of the reduced temperature T ¼ T/TNI. They were deduced from two intensity ratios R1 and R2 measured for two positions of the sample differing by a rotation of 901 around the normal of the film, taking into account the angle d between the absorption and emission axes. R1 and R2 are given by I XX I XZ I ZX I ZZ R1 ¼ and R2 ¼ (43) I XX þ 2I XZ I ZX þ 2I ZZ
Figure 11 Order parameter hP2 i as measured by fluorescence emission (filled circles) and absorption dichroism (open squares) and order parameter hP4 i (open circles) of polysiloxane doped with DANS as a function of the reduced temperature T. Reproduced with permission from Wolarz and Bauman [68]. Reprinted with permission of John Wiley & Sons, Inc.
324
Thierry Lefe`vre et al.
Iij (i, j ¼ X, Y, Z, see Figure 1) is the fluorescence intensity with the incident beam polarized in the i-direction and with the polarization direction of the analyzer along the j-axis. The variation of the order parameters with T is characteristic of low molecular-weight nematic liquid crystals, but the absolute values are lower. This was attributed to limitations of the rotational and translational motions of the mesogenic segments attached to the rigid backbone of the polymer. This constraint would lead to the formation of clusters that display different orientations, thus reducing the hP2 i value. Figure 11 also presents the hP2 i values as measured by UV linear dichroism following Equation (25). The lower value observed for fluorescence emission than for UV absorption is common for low molecular-weight liquid crystals and is attributed to an intermolecular energy transfer, which can lead to depolarization of the emission. In fluorescence spectroscopy, the orientation distribution of the guest probe is not necessarily identical to the actual orientation of the polymer chains, even if it is added at very small concentrations (i.e., a probe with high fluorescence efficiency). As a matter of fact, it is generally assumed that long linear probes are parallel to the polymer main chain, but this is not necessarily the case. Nevertheless, if the relation between the distribution of the probe axes and those of the polymer axes is known, the ODF of the structural units can be calculated from that of the probe thanks to the Legendre’s addition theorem. Finally, the added probe seems to be mainly located in the amorphous domains of the polymer [69] so that fluorescence spectroscopy provides information relative to the noncrystalline regions of the polymeric samples. Problems related to the use of a guest dye can be reduced if the polymer contains a fluorescent chemical group. Gohil and Salem [70] took advantage of such intrinsic fluorescence to characterize the in-plane distribution of orientation in biaxially drawn PET films. In these experiments, the chain-intrinsic fluorescent label is due to the formation of dimers by two terephthalic moieties, exclusively within the noncrystalline regions. A comparison between sequential and simultaneous drawing along the MD and TD directions was undertaken for a fixed MD draw ratio of 3.5 and various TD draw ratios. The orientational order was characterized by two ‘‘orientation ratios’’ RMD and RTD such that RMD ¼
I MD I TD and RTD ¼ I MD þ I TD I MD þ I TD
(44)
Figure 12 shows the MD and TD orientation ratios as a function of the TD draw ratio after biaxial drawing of the film. The curves coincide for the sequential and simultaneous processes up to a TD draw ratio of 2.7, beyond which RMD and RTD deviate from linearity for the sequential drawing. The amount of oriented chains in the TD and MD is thus the same up to a draw ratio of 2.7 but, above 2.7, the sequential stretching involves a reorientation of the polymers in the TD after the molecules were initially aligned in the MD. At equal draw ratios in the TD and MD, the simultaneous drawing actually leads to an isotropic distribution in the plane of the film, whereas in the sequential drawing, the chains are preferentially aligned in the TD.
Characterization of Molecular Orientation
325
Figure 12 Orientation ratios RMD (open symbols) and RTD (filled symbols) as a function of the TD draw ratio of PET films drawn for a sequential (circles) and simultaneous (triangles) process. Reproduced with permission from Gohil and Salem [70]. Reprinted with permission of John Wiley & Sons, Inc.
Recently, a formalism has been developed to determine the second and the fourth order parameters of films using polarized total internal reflection fluorescence (TIRF) [71]. Similarly to IR-ATR spectroscopy (Section 4), the experiment makes use of p- and s-polarized excitation, but the fluorescence emission (analyzed either in p- or s-direction) is detected normal to the substrate. Two approaches are developed based on the measurements of two intensity ratios. In the first one, the d angle has to be known experimentally or theoretically, and the order parameters hP2 i and hP4 i can be determined. In the second one, the order parameter hP2 i is obtained by another technique, for instance IR-ATR spectroscopy, which allows deducing the order parameter hP4 i and hcos2 di.
7. NMR SPECTROSCOPY NMR spectroscopy is a powerful technique to study molecular structure, order, and dynamics. Because of the anisotropy of the interactions of nuclear spins with each other and with their environment via dipolar, chemical shift, and quadrupolar interactions, the NMR frequencies depend on the orientation of a given molecular unit relative to the external magnetic field. NMR spectroscopy is thus quite valuable to characterize partially oriented systems. Solid-state NMR
326
Thierry Lefe`vre et al.
offers several ways to probe molecular order in oriented polymers. Since the detailed description of the available NMR techniques is outside the scope of this chapter and can be found elsewhere [72,73], only typical examples will be presented here. One problem with NMR spectroscopy of static polymer samples is the poor spectral resolution due to strong interactions in the solid state. Nevertheless, it has been shown that the hP2 i and hP4 i coefficients of the ODF can be determined for uniaxially oriented systems from the calculation of the second and fourth moments of resonance lines obtained by proton wide-line 1D NMR spectroscopy [72,73]. One way to increase the spectral resolution is by the isotopic labeling of some specific chemical groups so that one of the coupling tensors dominates in the 1D NMR spectra. Such strategy has been used successfully to study the distribution of orientation of polymer chains in highly oriented samples of deuterated PE [74] and PET [75] from the line shapes of 2H NMR spectra. Figure 13 shows the 2H NMR spectra of single-crystal mats and of a cold-drawn sample of PE with the magnetic field oriented either parallel or perpendicular to the preferred orientation axis. For both samples, the polymer chains in all-trans conformation are preferentially oriented along a single direction. When the external magnetic field, B0, is parallel to the chain direction, the C-2H bonds are perpendicular to B0, leading to a single doublet. The separation of these two lines depends on the angle between the C-2H bonds and the magnetic field. However, when B0 is perpendicular to the chain direction, the C-2H bonds are uniformly distributed in a plane forming an angle between 0 and 901 with B0, which leads to the characteristic spectrum with four singularities as seen in the right-hand side of Figure 13. For uniaxially oriented samples, the shape of this spectrum depends on the orientation distribution of the C-2H bonds and on the angle g between the magnetic field and the orientation direction. The quantitative line shape analysis as a function of g has shown that in both cases, the orientation distribution can be described as a simple Gaussian function with a width of 121 for the single-crystal
Figure 13 2H spectra of oriented polyethylene. Left, B0 parallel, right, B0 perpendicular to the orientation direction, respectively. Reproduced with permission from Hentschel et al. [74]. Copyright Elsevier 1981.
Characterization of Molecular Orientation
327
mats and 2.81 for the drawn sample, in excellent agreement with X-ray diffraction measurements on the same samples [74]. This method is particularly effective for highly oriented systems. Site-resolved orientation measurements with high spectral resolution can be achieved without the need of isotopic labeling either by the 2D synchronized magic angle spinning (MAS) technique [76] or the multidimensional DECODER (Direction Exchange with Correlation for Orientation-Distribution Evaluation and Reconstruction) technique [73,77,78]. The MAS technique averages out second-rank tensor interactions in the solid state and provides well-resolved NMR spectra of solid samples. MAS spectra are composed of center bands at the isotropic chemical shift frequencies of individual resonances flanked by sets of rotational sidebands. If the sample is partially ordered with the orientation axis not parallel to the rotor axis, phase and intensity modulations of the center band and the sidebands are observed, which depend on the position of the rotor at the time the spectrum is excited. Therefore, by synchronizing data acquisition with the rotor position, a 2D sideband pattern can be obtained for each resonance, which is highly dependent on tensor orientation. This technique has been used successfully to determine chain order in semicrystalline PET fibers using 13C resonances for the glycolic ethylene (O-CH2) and carbonyl groups [76]. Due to the limited number of sidebands with appreciable intensity observed for a given rotor frequency, only the hP2 i and hP4 i coefficients of the ODF of the PET chains were calculated from hP‘ i-weighted subspectra (Table 1). However, the use of the DECODER technique has allowed the determination of hP‘ i coefficients up to hP10 i for the same sample. In the 2D DECODER exchange NMR experiment, the sample is macroscopically rotated as a whole during the mixing time of the pulse sequence, thus allowing the correlation of two frequencies for two different sample orientations [78,79]. Through this correlation, more information can be obtained than from 1D rotation patterns and the orientation of chemical groups around the equivalent of two Euler angles can be determined. As seen in Table 1, the hP2 i and hP4 i coefficients of the oriented PET fibers obtained by the sync-MAS and DECODER techniques are in very good agreement, but the higher angular resolution of the DECODER experiment has allowed for determination of higher hP‘ i coefficients and to reconstruct the orientation distribution of chain axes. The results have shown that the orientation distribution is at least bimodal with a broad component and a narrow component [77].
Table 1 Order parameters of OCH2 group of PET fibers from 2D-sync-MAS and 2D-DECODER 13 C-NMR experiments
a
Technique
hP2 i
hP4 i
hP6 i
hP8 i
hP10 i
sync-MASa DECODERb
0.55 0.60
0.55 0.47
– 0.37
– 0.26
– 0.17
From Harbison et al. [76]. From Chmelka et al. [77].
b
328
Thierry Lefe`vre et al.
8. X-RAY DIFFRACTION AND ABSORPTION Wide-angle X-ray diffraction (WAXD) is one of the most commonly used techniques for the determination of molecular orientation in semicrystalline polymers [12]. It is particularly powerful as it provides a direct measurement of the complete distribution of orientation N(y, j) of the crystal axes with respect to the macroscopic sample coordinate system (OXYZ, Figure 1). A WAXD study of the diffracted intensity from a crystal plane of Miller indices hkl, Ihkl, through the rotation of the w and c angles (Figure 14) at a fixed Bragg angle (2yB) gives a pole figure, which is a map of the density of the normal to the crystal plane in the sample coordinate system. In samples exhibiting axial symmetry around the reference MD, a complete pole figures analysis is not necessary and the measurement of the diffraction intensity as a function of the angle w (obtained by rotating the sample around the ND axis or by using a 2D detector) is sufficient to determine the distribution of orientation N(w)hkl. It is thus possible to calculate any hP‘ ihkl coefficients for a given hkl plane for the crystalline phase of the polymer by integration over every possible orientation [2,80]: R p=2 I hkl ðwÞPn ðcos wÞ sinðwÞdw hP‘ ihkl ¼ 0 R p=2 (45) I hkl ðwÞ sinðwÞdw 0 where Ihkl(w) is the intensity of diffraction (after background correction) at the azimuthal angle w. The distribution of orientation N(w) of a given reflection may be reconstructed by insertion of the hP‘ ihkl coefficients in the relation: 1 X NðwÞhkl ¼ ðn þ 1=2ÞhP‘ ihkl P‘ ðcos wÞ (46) n¼0
Figure 14 Angles w and c defining the position of the normal to a given hkl crystal plane in the sample reference system. Ix, incident X-ray beam; Ihkl, diffracted intensity; yB, Bragg angle. Adapted from Lafrance et al. [82]. Reprinted with permission of John Wiley & Sons, Inc.
Characterization of Molecular Orientation
329
In the case of uniaxial cylindrical symmetry around the MD, the hP‘ ihkl values calculated from different crystal planes can be related to the hP‘ i coefficients of any of the three crystallographic angles using the Legendre addition theorem (see Section 4). For example, the hP‘ ic coefficients corresponding to the crystalline c-axis is given by [81] hP‘ ihkl hP ‘ ic ¼ (47) P‘ ðcos bhkl Þ where bhkl is the angle between the normal to the considered (hkl) plane and the c-axis. This relation is particularly useful to determine polymer chain orientation since reflections from planes that are perpendicular to the polymer chains (00l) are frequently absent or too weak to be analyzed with sufficient accuracy. In addition, in the case of unit cells with orthogonal crystal axes, geometrical consideration leads to the following expression for the second moments of the distribution of orientation (Herman’s orientation function) of the three crystal axes: hP 2 i a þ h P 2 i b þ h P 2 i c ¼ 0 (48) A nice example of the strength of WAXD to study molecular orientation in a semicrystalline polymer was given by Lafrance et al. [82]. In this work, WAXD was used to study the development of crystalline orientation in drawn ultrahigh-molecular weight PE films prepared by the gelation-crystallization method. Azimuthal profiles were measured to determine the presence of any preferred orientation of the crystals in the undrawn film (Figure 15). Scans measured with the incident beam perpendicular to the sample surface (A) show that the crystal a- and b-axes are randomly distributed around the ND.However, scans obtained with the beam parallel to the TD (B) show that the c-axis, and thus the PE chains, is oriented perpendicular to the surface of the film, the 002 reflection being centered at w ¼ 01. The average hP2 ic coefficient calculated from the 110, 200, 020, and 002 reflections is equal to 0.67 with respect to ND. Therefore, lamellar growth occurred in the plane of the film as the b-axis is that of the crystal growth for PE. Upon drawing, at 1301C, a change of the orientation of the PE chains from the normal direction to the drawing direction was observed. In addition, as shown in Figure 16, a marked decrease of the intensity of the Bragg peak for the 200 reflection relative to that of the 020 reflection was observed at low draw ratio (lo10). This variation, which occurs in the early stages of drawing, was assigned to development of double orientation during the transformation from the lamellar to the fibrillar morphology, with the a-axis oriented parallel to ND. Upon further drawing, the width of the azimuthal scans for different reflections was observed to decrease, indicating a narrowing of the distribution of orientation even at very high draw ratios. From these scans, hP‘ i coefficients were calculated using Equations (45) and (47). Although the hP2 i coefficient is a convenient index to characterize the orientation and is commonly measured by WAXD for semicrystalline polymers, it is only an average value and different distributions of orientation could give the same hP2 i coefficient (Section 2). It has been shown that higher hP‘ i coefficients are required to fully characterize the distribution of orientation [83]. This is
330
Thierry Lefe`vre et al.
Figure 15 X-ray intensity measured as a function of the polar angle w for an undrawn ultrahigh molecular weight PE film. Incident beam directed through the thickness of the film (A), and parallel to the plane of the film (B). Reproduced with permission from Lafrance et al. [82]. Reprinted with permission of John Wiley & Sons, Inc.
particularly important for highly oriented samples since hP2 i increases rapidly near its maximum value and remains constant afterward. This is clearly shown in Figure 17 where the hP2 ic , hP26 ic , hP60 ic coefficients were calculated from the 020 and 002 reflections as a function of the draw ratio. At draw ratios between 5 and 10, the hP2 ic values approach the theoretical limit of unity, showing that the crystal phase has already attained a high degree of orientation. At higher draw ratios, the hP2 ic coefficients show no additional significant variation because the secondorder Legendre polynomial is much broader than the narrow experimental intensity distributions. However, Figure 17 shows that higher-order coefficients of the polynomial series such as hP26 ic and hP60 ic can be used efficiently to follow the evolution of the orientation up to l ¼ 50. This example clearly emphasizes the
Characterization of Molecular Orientation
331
Figure 16 Effect of l on the ratio of the 200/020 integrated intensities measured in the polar scans for a drawn ultra-high molecular weight PE film. Reproduced with permission from Lafrance et al. [82]. Reprinted with permission of John Wiley & Sons, Inc.
importance of using techniques that allow the determination of hP‘ i coefficients higher than hP2 i for highly oriented samples. For more complex morphologies showing biaxial orientation, a pole figure analysis involving the rotation of the w and c angles is necessary to fully characterize the orientation [84]. Near-edge X-ray absorption fine structure spectroscopy (NEXAFS), using linearly polarized synchrotron light, also provides a quantitative measurement of the direction and magnitude of orientation in anisotropic systems [85]. NEXAFS linear dichroism can also be recorded at high spatial resolution (o50 nm) using scanning transmission X-ray microscopy (STXM) [85]. Recently, STXM has been used for the first time to quantitatively map the level of orientation of the carbonyl bonds of the protein polypeptide chains in silkworm [86] and spider silks [87] at spatial resolution better than 50 nm. For these experiments, the absorbance of the 288.25 eV X-ray band due to the C 1s-p CQO transition of the protein peptide groups was measured with the electric field vector of the X-ray beam polarized parallel (Ap) and perpendicular (As) to the fiber axis, thus allowing one to calculate for each pixel the second moment of the orientation function P2 ðcos gÞ as described for IR transmission measurements in Section 4. In this case, g represents the angle between the moment vector of the C 1s-p CQO transition and the fiber axis. An example of such orientation map obtained for a thin section of Nephila clavipes dragline silk fiber of about 3 mm in diameter is shown in Figure 18 [87]. Dragline silk presents a very fine microstructure in which small, highly oriented, domains are dispersed in a dominant, moderately oriented, matrix with several small unoriented domains.
332
Thierry Lefe`vre et al.
Figure 17 Values of the hP2 ic , hP26 ic , hP60 ic coefficients as a function of l for the 020 and 002 reflections for a drawn ultra-high molecular weight PE film. Reproduced with permission from Lafrance et al. [82]. Reprinted with permission of John Wiley & Sons, Inc.
Figure 18 Quantitative hP2 ðcos gÞi orientation map of a fiber reeled at 0.5 cm/s. Black areas correspond to unoriented regions, whereas bright areas correspond to more highly oriented regions. Reproduced with permission from Rousseau et al. [87]. Copyright 2007 American Chemical Society.
Characterization of Molecular Orientation
333
Since the transition moment for the 288.25 eV band is perpendicular to the plane of the protein peptide bond, the negative values of the P2 ðcos gÞ coefficient show that the peptide CQO groups are preferentially oriented perpendicular to the fiber axis. There is clearly an uneven spatial distribution of highly oriented (bright) domains (Figure 18), especially at the surface of the fiber where a skin B30–120 nm thick is present. These oriented domains are associated with the anti-parallel b-sheets formed by the repeating alanine sequences present in spider dragline silk. This example shows that STXM is a powerful technique to probe at high spatial resolution the microstructure of oriented polymer samples.
9. CONCLUSION As seen in this chapter, the theory and procedures for orientation measurements are well established, including for quantitative characterization. These methods can provide very accurate and useful information in the fields of synthetic, natural, and bio-inspired macromolecules. To this aim, researchers can make use of a wide range of techniques, each having its advantages and limitations. As judged from the recent literature, the studies devoted to the quantification and characterization of molecular orientation still represent a very dynamic research field and advances still continue to emerge. Further progresses in the development of new methods and new techniques to characterize orientational order are thus expected in the future.
REFERENCES 1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16 17
R.-J. Roe, J. Appl. Phys., 36 (1965) 2024–2031. R.-J. Roe and W.R. Krigbaum, J. Chem. Phys., 40 (1964) 2608–2615. D.A. Jarvis, I.J. Hutchinson, D.I. Bower and I.M. Ward, Polymer, 21 (1980) 41–54. S. Nomura, H. Kawai, I. Kimura and M. Kagiyama, J. Polym. Sci., Part A2: Polym. Phys., 8 (1970) 383–400. I.M. Ward, Adv. Polym. Sci., 66 (1985) 81–115. C. Sourisseau, Chem. Rev., 104 (2004) 3851–3891. C.-P. Lafrance, A. Nabet, R.E. Prud’homme and M. Pe´zolet, Can. J. Chem., 73 (1995) 1497–1505. S. Nomura, N. Nakamura and H. Kawai, J. Polym. Sci., Part A2: Polym. Phys., 9 (1971) 407–420. F. Lagugne´-Labarthet, T. Buffeteau and C. Sourisseau, Appl. Spectrosc., 54 (2000) 699–705. H. Pottel, W. Herreman, B.W. Ven der Meer and M. Ameloot, Chem. Phys., 102 (1986) 37–44. F.A. Bettelheim and R.S. Stein, J. Polymer Sci., 27 (1958) 567–569. R.E. Pepper and R.J. Samuels, In: H.F. Mark, N.M. Bikales, C.G. Overberger, G. Menges and J.I. Kroschwitz (Eds.), Encyclopedia of Polymer Science and Engineering, 2nd ed., Wiley, New York, 1988, Vol. 14, pp. 261–298. P. Lapersonne, J.F. Tassin and L. Monnerie, Polymer, 35 (1994) 2192–2196. I.M. Ward, Structure and Properties of Oriented Polymers, 2nd ed., Chapman & Hall, London, 1997. E. Abtal and R.E. Prud’homme, Polymer, 37 (1996) 3805–3811. H. Fong and D.H. Reneker, J. Polym. Sci., Part B: Polym. Phys., 37 (1999) 3488–3493. L. Messe´, M. Pe´zolet and R.E. Prud’homme, Polymer, 42 (2001) 563–575. A.K. Oultache, X.H. Kong, C. Pellerin, J. Brisson, M. Pe´zolet and R.E. Prud’homme, Polymer, 42 (2001) 9051–9058. A. Natansohn, P. Rochon, J. Gosselin and S. Xie, Macromolecules, 25 (1992) 2268–2273.
334
Thierry Lefe`vre et al.
18 K. Hongladarom, W.R. Burghardt, S.G. Baek, S. Cemetwala and J.J. Magda, Macromolecules, 26 (1993) 772–784. 19 A. Ajji, J. Gue`vremont, R.G. Matthews and M.M. Dumoulin, J. Plast. Film Sheet., 15 (1999) 256–268. 20 T. Buffeteau, F. Lagugne´-Labarthet, M. Pe´zolet and C. Sourisseau, Macromolecules, 34 (2001) 7514–7521. 21 E. Klimov, G.G. Hoffmann, A. Gummeny and H.W. Siesler, Macromol. Rapid Comm., 26 (2005) 1093–1098. 22 J.P. Faivre, B. Jasse and L. Monnerie, Polymer, 26 (1985) 879–883. J.F. Tassin and L. Monnerie, Macromolecules, 21 (1988) 1846–1854. 23 D. Lefebvre, B. Jasse and L. Monnerie, Polymer, 22 (1981) 1616–1620. 24 M. Wang, J.H. Yu, D.L. Kaplan and G.C. Rutledge, Macromolecules, 39 (2006) 1102–1107. 25 J.M. Chalmers and N.J. Everall, Analusis, 28 (2000) 53–64. 26 N.P. Camacho, P. West, P.A. Torzilli and R. Mendelsohn, Biopolymers, 62 (2001) 1–8. 27 C. Pellerin, M. Pe´zolet and P.R. Griffiths, Macromolecules, 39 (2006) 6546–6551. 28 C.G. Bazuin and X.-D. Fan, Macromolecules, 31 (1998) 1321–1328. 29 J.L. Koenig, S.W. Cornell and D.E. Witenhafer, J. Polym. Sci., Part A2: Polym. Phys., 5 (1967) 301–313. 30 X.M. Zhang and A. Ajji, Polymer, 46 (2005) 3385–3393. 31 K.C. Cole, C. Depecker, M. Jutigny, J.M. Lefebvre and P. Krawczak, Polym. Eng. Sci., 44 (2004) 231–240. 32 N.J. Everall and A. Bibby, Appl. Spectrosc., 51 (1997) 1083–1091. N.J. Everall and A. Bibby, Appl. Spectrosc., 53 (1999) 461A. 33 E.-M. Shin and J.L. Koenig, Appl. Spectrosc., 56 (2002) 1251–1258. 34 K.H. Park, Y. Liang, S.H. Kim and H.S. Lee, Macromolecules, 39 (2006) 1832–1838. 35 M.R. Smith, S.J. Cooper, D.J. Winter and N. Everall, Polymer, 47 (2006) 5691–5700. 36 K.C. Cole, J. Gue`vremont, A. Ajji and M.M. Dumoulin, Appl. Spectrosc., 48 (1994) 1513–1528. 37 J. Gue`vremont, A. Ajji, K.C. Cole and M.M. Dumoulin, Polymer, 36 (1995) 3385–3392. 38 K.C. Cole, H. Ben Daly, B. Sanschagrin, K.T. Nguyen and A. Ajji, Polymer, 40 (1999) 3505–3513. 39 H. Ben Daly, K.C. Cole, K.T. Nguyen and B. Sanschagrin, J. Appl. Polym. Sci., 104 (2007) 1319–1327. 40 A.K. Kalkar, H.W. Siesler, I. Zebger, F. Pfeifer, A. Ameri, S. Michel and U. Hoffmann, In: P.R. Griffiths and J.M. Chalmers (Eds.), Handbook of Vibrational Spectroscopy, , Wiley, Chichester, 2001, Vol. 1, pp. 2559–2575. 41 T. Buffeteau and M. Pe´zolet, Appl. Spectrosc., 50 (1996) 948–955. 42 C. Pellerin, R.E. Prud’homme and M. Pe´zolet, Macromolecules, 33 (2000) 7009–7015. 43 Y.X. Wang, C. Pellerin, C.G. Bazuin and M. Pe´zolet, Macromolecules, 38 (2005) 4377–4383. 44 D.I. Bower, J. Polym. Sci.: Polym. Phys. Ed., 10 (1972) 2135–2153. 45 B.J. Berne, P. Pechukas and G.D. Harp, J. Chem. Phys., 49 (1968) 3125–3129. D.I. Bower, J. Polym. Sci.: Polym. Phys. Ed., 19 (1981) 93–107. 46 J. Purvis and D.I. Bower, Polymer, 15 (1974) 645–654. 47 M. Pigeon, R.E. Prud’homme and M. Pe´zolet, Macromolecules, 24 (1991) 5687–5694. 48 B.J. Kip, M. van Gurp, S.P.C. van Heel and R.J. Meier, J. Raman Spectrosc., 24 (1993) 501–510. 49 J.M. Citra, D.B. Chase, R.M. Ikeda and K.H. Gardner, Macromolecules, 28 (1995) 4007–4012. 50 M. Tanaka and R.J. Young, J. Macromol. Sci. B, 44 (2005) 967–999. M. Tanaka and R.J. Young, Macromolecules, 39 (2006) 3312–3321. 51 G. Voyiatzis, G. Petekidis, D. Vlassopoulos, E. Kamitsos and A. Bruggeman, Macromolecules, 29 (1996) 2244–2252. 52 J.H. Nobbs and D.I. Bower, Polymer, 19 (1978) 1100–1103. 53 J. Purvis and D.I. Bower, J. Polym. Sci.: Polym. Phys. Ed., 14 (1976) 1461–1484. J. Purvis, D.I. Bower and I.M. Ward, Polymer, 14 (1973) 398–400. 54 F. Lagugne´-Labarthet and C. Sourisseau, J. Raman Spectrosc., 27 (1996) 491–498. 55 E. Anglaret, M. Brunet, B. Desbat, P. Keller and T. Buffeteau, Macromolecules, 38 (2005) 4799–4810. 56 S. Frisk, R.M. Ikeda, D.B. Chase and J.F. Rabolt, Appl. Spectrosc., 58 (2004) 279–286. 57 S. Frisk, R.M. Ikeda, D.B. Chase and J.F. Rabolt, Appl. Spectrosc., 57 (2003) 1053–1057. 58 C. Sourisseau and D. Talaga, Appl. Spectrosc., 60 (2006) 1368–1376. 59 G. Turrell, In: D.J. Gardiner and P.R. Graves (Eds.), Practical Raman spectroscopy, Springer-Verlag, Berlin, 1989, pp. 13–54.
Characterization of Molecular Orientation
335
60 G. Turrell, J. Raman Spectrosc., 15 (1984) 103–108. 61 G. Turrell, M. Delhaye and P. Dhamelincourt, In: G. Turrell and J. Corset (Eds.), Raman MicroscopyDevelopments and Applications, Elsevier, Amsterdam, 1996, pp. 27–49. 62 F. Lagugne´-Labarthet, J.L. Bruneel, T. Buffeteau, C. Sourisseau, M.R. Huber, S.J. Zilker and T. Bieringer, Phys. Chem. Chem. Phys., 2 (2000) 5154–5167. F. Lagugne´-Labarthet, J.L. Bruneel and C. Sourisseau, J. Phys. Chem., 108 (2004) 1267–1278. F. Lagugne´-Labarthet, T. Buffeteau and C. Sourisseau, Macromol. Symp., 137 (1999) 75–82. 63 M.-E. Rousseau, L. Beaulieu, T. Lefe`vre, J. Paradis, T. Asakura and M. Pe´zolet, Biomacromolecules, 7 (2006) 2512–2521. M.-E. Rousseau, T. Lefe`vre, L. Beaulieu, T. Asakura and M. Pe´zolet, Biomacromolecules, 5 (2004) 2247–2257. 64 T. Buffeteau, F. Lagugne´-Labarthet, C. Sourisseau, S. Kostromine and T. Bieringer, Macromolecules, 37 (2004) 2880–2889. 65 T. Lefe`vre, M.-E. Rousseau and M. Pe´zolet, Appl. Spectrosc., 60 (2006) 841–846. 66 C.R. Desper and I. Kimura, J. Appl. Phys., 38 (1967) 4225–4233. R.-J. Roe, J. Polym. Sci., Part A2: Polym. Phys., 8 (1970) 1187–1194. 67 J.H. Nobbs, D.I. Bower, I.M. Ward and D. Patterson, Polymer, 15 (1974) 287–299. 68 E. Wolarz and D. Bauman, J. Polym. Sci., Part B: Polym. Phys., 31 (1993) 383–387. 69 J.H. Nobbs, D.I. Bower and I.M. Ward, Polymer, 17 (1976) 25–36. 70 R.M. Gohil and D.R. Salem, J. Appl. Polym. Sci., 47 (1993) 1989–1998. 71 A.F. Runge, S.S. Saavedra and S.B. Mendes, J. Phys. Chem. B, 110 (2006) 6721–6731. 72 V.J. McBrierty and K.J. Packer, Nuclear Magnetic Resonance of Solid Polymers. Cambridge University Press, Cambridge, 1993; H.W. Spiess. In: I.M. Ward (Ed.), Structure and Properties of Oriented Polymers, 2nd ed., Chapman & Hall, London, 1997. 73 K. Schmidt-Rohr and H.W. Spiess, Multidimensional Solid-State NMR and Polymers, Academic Press, London, 1994. 74 R. Hentschel, H. Sillescu and H.W. Spiess, Polymer, 22 (1981) 1516–1521. 75 S. Ro¨ber and H.G. Zachmann, Polymer, 33 (1992) 2061–2075. 76 G.S. Harbison, V.-D. Vogt and H.W. Spiess, J. Chem. Phys., 86 (1987) 1206–1218. 77 B.F. Chmelka, K. Schmidt-Rohr and H.W. Spiess, Macromolecules, 26 (1993) 2282–2296. 78 P.M. Henrichs, Macromolecules, 20 (1987) 2099. 79 K. Schmidt-Rohr, M. Hehn, D. Schaefer and H.W. Spiess, J. Chem. Phys., 97 (1992) 2247–2262. 80 H.D. Deas, Acta Crystallogr., 5 (1952) 542. 81 R. Lowell and G.R. Mitchell, Acta Crystallogr., A37 (1981) 135. 82 C.-P. Lafrance, J. Debigare´ and R.E. Prud’homme, J. Polym. Sci., Part B: Polym. Phys., 31 (1993) 255–264. 83 C.-P. Lafrance, M. Pe´zolet and R.E. Prud’homme, Macromolecules, 24 (1991) 4948–4956. 84 R.J. Pazur and R.E. Prud’homme, Macromolecules, 29 (1996) 119–128. 85 H. Ade. In: J.A. Samson and D.L. Ederer (Eds.), X-ray Spectromicroscopy. Experimental Methods in Physical Sciences, Vol. 32. Academic Press, New York, 1998, pp. 225–249. 86 D. Herna´ndez-Cruz, M.-E. Rousseau, M.M. West, M. Pe´zolet and A.P. Hitchcock, Biomacromolecules, 7 (2006) 836–843. 87 M.-E. Rousseau, D. Herna´ndez Cruz, M.M. West, A.M. Hitchcock and M. Pe´zolet, J. Am. Chem. Soc., 129 (2007) 3897–3905.
This page intentionally left blank
CHAPT ER
9 Polymer Networks: Elastomers B. Erman and J.E. Mark
Contents
1. Introduction 2. Structure of a Typical Network 3. Elementary and More Advanced Molecular Theories 3.1 Elasticity of the single chain 3.2 The elastic free energy of the network 3.3 The reduced stress and the elastic modulus 3.4 The affine network model 3.5 The phantom network model 3.6 More advanced molecular theories 3.7 Contribution of trapped entanglements to the modulus 4. Phenomenological Theories 5. Some Relevant Simulations 5.1 Gelation 5.2 Distribution functions and stress–strain isotherms 5.3 Crystallization 5.4 Filler reinforcement 6. Swelling of Networks and Responsive Gels 7. Enthalpic and Entropic Contributions to Rubber Elasticity: The Force–Temperature Relations 8. Multimodal Elastomers 8.1 General information 8.2 Bimodal networks 8.3 Trimodal networks 9. Liquid–Crystalline Elastomers 9.1 General information 9.2 Main-Chain liquid–crystalline elastomers 9.3 Side-Chain liquid–crystalline elastomers 9.4 Theory 10. Novel Reinforced Elastomers 10.1 Sol–Gel in-situ precipitated ceramic particles 10.2 Non-Spherical particles 10.3 Magnetic particles 10.4 Layered fillers 10.5 Polyhedral oligomeric silsesquioxanes (POSS)
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00409-1
338 339 341 341 344 344 345 346 347 350 351 352 352 352 353 354 356 358 359 359 359 364 365 365 366 368 370 370 370 371 372 372 372
r 2008 Elsevier B.V. All rights reserved.
337
338
B. Erman and J.E. Mark
10.6 Nanotubes 10.7 Porous fillers 10.8 Fillers with controlled interfaces 11. Further Comments on Some Characterization Techniques 11.1 Optical and spectroscopic techniques 11.2 Microscopies 11.3 NMR 11.4 Small-Angle scattering 11.5 Brillouin scattering 11.6 Pulse propagation Acknowledgement References
373 373 373 374 374 374 375 375 376 376 376 377
1. INTRODUCTION A network can be formed from a polymer by constraining pairs of its repeat units, typically by introducing cross-links between chains close to one another. The reaction is typically carried out in the isotropic, bulk state [1,2]. If approximately 1 repeat unit out of 10 along the chain backbone participates in this type of ‘‘cross-linking’’, then the result is an infusible, relatively hard material [3]. Examples of such materials are phenol formaldehyde resins and epoxy cements. If only approximately 1 out of 100 repeat units are involved in cross-links, however, then above its glass transition temperature the material has elastomeric properties similar to those of natural rubber, specifically high deformability with recoverability. They are therefore described as exhibiting ‘‘rubber-like elasticity’’ [4,5]. Both types of networks have been called ‘‘thermosets’’, but modern usage applies this term more to the very heavily cross-linked networks. The more lightly cross-linked, elastomeric materials are the focus of this chapter. More specifically, the rubber-like materials introduced above consist of relatively long polymeric chains having a high degree of flexibility and mobility, which are joined into a network structure [6,7]. The requirement of flexibility and mobility is associated with the very high deformability. As a result of an externally imposed stress, the long chains may alter their configurations, an adjustment which takes place relatively rapidly because of the high chain mobility. The requirement of having the chains linked into a network structure is associated with solid-like features, where the chains are prevented from flowing relative to each other under external stresses. As a result, a typical rubber may be stretched up to about 10 times its original length [8,9]. On removal of the external force, it rapidly recovers its original dimensions, with essentially no residual or non-recoverable strain. As a result of these unique mechanical properties,
Polymer Networks: Elastomers
339
rubbers find important usages ranging from automobile tires to heart valves, and gaskets in jet planes, and space vehicles [10]. In ordinary solids such as crystalline or amorphous glassy materials, an externally applied force changes the distance between neighboring atoms, resulting in interatomic or intermolecular forces. In these materials, the distance between two atoms should only be altered by no more than a fraction of an angstrom if the deformation is to be recoverable. At higher deformations, the atoms slide past each other, and either flow takes place or the material fractures. The response of rubbers on the other hand is almost entirely intramolecular [4,5]. Externally applied forces transmitted to the long chains through the linkages let their extremities change the conformations of the chains, and each chain acts like a spring in response to the external stress. The molecular mechanisms relating to rubber-like elasticity were recognized in the early 1930s. Rigorous statistical mechanical theories describing the mechanical behavior of rubbers were given by Guth and James [11], Wall [12], Flory [13], and Flory and Rehner [14,15]. The present understanding of the molecular basis of rubber elasticity owes much to these early theories. They give an idealized picture of rubber elasticity, but at the same time form the basis of more advanced molecular theories of such elasticity, which describe the effects of intermolecular entanglements observed in real networks. Developments in the field from the beginning up to the present have been reviewed in several monographs (see, e.g., Treloar [16], Mark and Erman [4], and the more recent monograph by Erman and Mark [5]). In this chapter we first discuss the structural features of networks that contribute to the stress upon deformation. We discuss the simple classical models of elasticity and the departures from these simple models. Specifically, we differentiate between two classes of models, (i) the constraint models, which assume that the total elastic energy of the network equals the sum of the individual network chain energies, and (ii) trapped entanglement models, which assume that entanglements that are trapped during the cross-linking stage contribute additionally to the network elastic energy. We also give the molecular interpretation of coefficients obtained from the phenomenological theories. Some simulations relevant to rubber-like elasticity are then briefly described. This is followed by a discussion of swollen networks (‘‘gels’’), and responsive gels because of their increasing interest. We then discuss the thermoelastic (force– temperature) behavior of networks, followed by information on multimodal networks, liquid–crystalline elastomers, novel reinforcing fillers, and conclude with some further comments on characterization methods.
2. STRUCTURE OF A TYPICAL NETWORK As already mentioned, a network can be obtained by linking polymer chains together, and this linkage may be either physical or chemical. Physical linking can be obtained by (i) absorption of chains onto the surface of finely divided particulate fillers, (ii) formation of small crystallites, (iii) coalescence of ionic groups, or (iv) coalescence of glassy sequences in block copolymers.
340
B. Erman and J.E. Mark
These physical cross-links are, in general, not permanent and may disappear on swelling or increase in temperature. The corresponding networks are referred to as ‘‘physical’’ or ‘‘thermoreversible’’ and are not considered in this chapter. The reader may refer to Burchard and Ross-Murphy [17–19] for further information on such materials. Chemical cross-links may be obtained by randomly joining segments in already formed chains, by random copolymerization, or by end-linking functionally-terminated chains. Sulfur cures, peroxide cures, and high-energy irradiations are familiar methods of random cross-linking [1,2]. Copolymerization of monomers where at least one type has three or more reactive sites also leads to randomly cross-linked networks. Formation of networks by end-linking individual chains by f-functional linkages is the most appropriate method of forming well-defined structures, where the functionality f of a linkage is defined as the number of chains meeting at the junction. A network is called perfect if its junctions have a functionality of at least three, it has no dangling chains (chains attached to the network only at one of their ends), and it has no loops (chains with both ends meeting at the same junction). Properties of perfect networks are discussed in this chapter. The reader may refer to Erman and Mark [5,20] and to the original work by Flory [21] and Flory and Erman [22] for the structure and properties of imperfect networks. The structure of a perfect network may be defined by two variables, the cycle rank x and the average junction functionality f. Cycle rank is defined as the number of chains that must be cut to reduce the network to a tree. The three other parameters used often in defining a network are (i) the number of network chains (chains between junctions) n, (ii) the number of junctions m, and (iii) the molecular weight Mc of chains between two junctions. They may be obtained from x and f using the relations x n¼ 1 ð2=fÞ m¼
2n f
1 ð2=fÞ rN A Mc ¼ x=V0
(1) (2)
(3)
where r is the density, V0 is the reference volume of the network, and NA is Avogadro’s number. The cycle rank completely defines the connectivity of a network and is the only parameter that contributes to the elasticity of a network, as will be discussed further in the following section on elementary molecular theories. In several other studies, contributions from entanglements that are trapped during crosslinking are considered in addition to the chemical cross-links [23,24]. The trapped entanglement model is also discussed below. In a typical elastomer, the number of skeletal bonds in a network chain range from about 100 to 700 [25]. Networks with chains shorter than 100 bonds have
Polymer Networks: Elastomers
341
low extensibilities. Those having chains much larger than 700 bonds may have very high extensibilities but are too weak to serve as load-carrying materials. It is possible to prepare ‘‘bimodal’’ networks, however, by end-linking very short and very long chains to form networks of significant toughness, as described below and elsewhere [26,27].
3. ELEMENTARY AND MORE ADVANCED MOLECULAR THEORIES The basic postulate of elementary molecular theories of rubber elasticity states that the elastic free energy of a network is equal to the sum of the elastic free energies of the individual chains. In this section, the elasticity of the single chain is discussed first, followed by the elementary theory of elasticity of a network. Corrections to the theory coming from intermolecular correlations, which are not accounted for in the elementary theory, are discussed separately.
3.1 Elasticity of the single chain The chemical structure of a polymer chain determines its statistical properties, such as its average dimensions in space and its flexibility. These parameters, in turn, affect various properties of a network consisting of these chains. A detailed understanding of the single chain is therefore important in this regard. Using poly(dimethylsiloxane) (PDMS) [–Si(CH3)2O–]n as an example, the chain consists of silicon and oxygen atoms located in alternating order along the backbone, with the CH3’s on the Si atoms constituting the side groups. The lengths of the bonds and bond angles are approximately constant, but torsional rotations at angles f may take place relatively easily about the skeletal bonds. Large rotations may take place about the skeletal bonds, as a result of which the chain may take different spatial conformations, with varying values of the endto-end vector r of the chain. In most molecular theories of rubber-like elasticity, the individual chains are approximated by either the freely jointed or the freely rotating chain model. In reality, however, rotations about each bond are subject to potentials that arise from the intrinsic torsional potential of the backbone bond and from steric attractive and repulsive forces from neighboring atoms along the chain. The energy to which the bond torsional angle fi is subjected exhibits three minima, referred to as the three ‘‘isomeric states’’ or ‘‘isomeric minima’’. Of course, the numbers of isomeric states may be smaller or larger than three, depending on the chain architecture. In general, the three minima are approximately spaced at 1201 intervals and are referred to as the trans (t), gauche+ (g+), and gauche (g) states. The shape of a chain changes continuously and rapidly as each bond fluctuates about an isomeric minimum, with an amplitude of the order of 7601, and occasionally goes over the energy peak to another isomeric minimum. The rate of transition from one isomeric minimum to another, which is on the order of one per nanosecond at sufficiently high temperatures, depends primarily on the temperature and on the height of the energy barriers. These transitions determine
342
B. Erman and J.E. Mark
the dynamics of the chain, and determine in part its glass transition temperature, Tg. Equilibrium properties of the chain, on the other hand, are influenced by the energy levels of the isomeric minima, as well as their locations. In the case of hydrocarbon polymers such as polyethylene, the t state in a randomly configured chain is more populated than the g+ and g states. The average number of bonds in the t, g+, and g states is determined according to the Boltzmann distribution of statistical mechanics [28–30]. According to statistical mechanical arguments, the number of each type of isomeric state in a chain remains essentially the same when the chain is stretched at its two ends. The change in the end-to-end vector takes place by the redistribution of the isomeric states along the chain. As the number of each type of isomeric state remains the same, the total internal energy of the chain remains constant during stretching. The elasticity of the chain resulting from redistribution of isomeric states is referred to as ‘‘entropic’’ elasticity, and a major part of the elasticity of a network is entropic. If part of the work done in deformation is used to change the relative populations of isomeric states, the bond angles, and the chain lengths, a change in internal energy takes place, which results in an ‘‘energetic’’ component of the elasticity. The relationship of the entropic and energetic components to molecular constitution in a network is discussed in the following sections. The vector r joining the two ends of the chain takes different values resulting from rotations about the individual bonds. For chains with more than about 50 skeletal bonds, the probability W(r)dxdydz that one end of r is at the origin and the other end is in an infinitesimal volume dV ¼ dxdydz is satisfactorily represented by the Gaussian function [31,32] !3=2 ! 3 3r2 WðrÞdxdydz ¼ exp 2 dxdydz (4a) 2 r 0 2p r2 0 Here, /r2S0 represents the average of the squared end-to-end vectors, and the subscript zero indicates that the chain is in the unperturbed or so-called theta state [21]. It is now well established that chains in the bulk undiluted state are in the unperturbed state. Equation (4a) represents the probability distribution of the vectorial quantity r. A less detailed form of representation is the distribution w(r) showing the probability that the magnitude r of r has a certain value irrespective of direction. Thus, the probability that the chain end-to-end length is in the range r to r+dr irrespective of its direction is !3=2 ! 3 3r2 WðrÞdr ¼ exp 2 4pr2 dr (4b) 2p r2 0 2 r 0 A schematic representation of the Gaussian function of Equation (4b) is given by the dashed curve in Figure 1. The abscissa is normalized by dividing the endto-end distance by the contour length of the chain, and the ordinate is made nondimensional (unitless) by multiplying w(r) by the contour length. For chains having fewer than 50 bonds, such as the short chains in a bimodal network, for example, the distribution departs markedly from the Gaussian limit.
Polymer Networks: Elastomers
343
Figure 1 Distributions for the end-to-end distance of a PDMS chain having n ¼ 20 skeletal ˚ . The Fixman–Alben distribution (dotted curve) and that from a bonds of length l ¼ 1.64 A Monte Carlo simulation (solid curve) are compared with the Gaussian approximation (dashed curve).
Among various representations of w(r) for short chains are the Hermite series [31,32], the Fixman–Alben distribution [33], and Monte Carlo simulations [34]. The Fixman–Alben distribution is given by WðrÞdr / expðar2 þ b2 r4 Þ4pr2 dr
(4c)
where a and b are coefficients. This distribution and results of Monte Carlo simulations for a PDMS chain of 20 skeletal bonds are compared with the Gaussian approximation in Figure 1. The molecular theories of networks to be presented in the following paragraphs are based on the Gaussian picture of the individual network chains. With reference to the form of the distribution function, these theories are referred to as ‘‘Gaussian theories’’. The elastic free energy Ael of a Gaussian chain is related to the probability distribution W(r) by the thermodynamic expression [5] Ael ¼ CðTÞ kT ln WðrÞ
(5)
where C(T) is a function only of temperature T, and k is the Boltzmann constant. Substituting Equation (4a) into Equation (5) leads to ! 3kT r2 (6) Ael ¼ An ðTÞ þ 2 r2 0 Here, A(T) is a function of temperature alone. Equation (6) represents the elastic free energy of a Gaussian chain with ends fixed at a separation of r. The average force required to keep the two ends at this separation is obtained from the thermodynamic expression [28] @Ael f¼ (7) dr T
344
B. Erman and J.E. Mark
¼
! 3kT r r2 0
(8)
where Equation (8) is obtained by substituting Equation (6) into Equation (7). The subscript T denotes differentiation at fixed temperature. Equation (8) shows that the single chain behaves like a linear spring, with spring constant equal to 3kT//r2S0.
3.2 The elastic free energy of the network The total elastic free energy DAel of the network relative to the undeformed state is obtained by summing Equation (6) over the n chains of the network [4] 3kT X 2 2 DAel ¼ 2 r r 0 (9) 2 r 0 n ! 3nkT r2 1 ¼ (10) 2 r2 0 where /r2S ¼ Sr2/n is the average square of the end-to-end vectors of chains in the deformed network. Substituting 2 2 2 2 (11) r ¼ x þ y þ z into Equation (10) and using the fact that chain dimensions are isotropic in the undeformed state 2 2 2 2 r 0 x 0¼ y 0¼ z 0¼ (12) 3 one obtains " # 2 2 y z nkT x2 þ þ 3 DAel ¼ (13) 2 x2 0 y2 0 z2 0 The ratios of mean-squared dimensions appearing in Equation (13) are microscopic quantities. To express the elastic free energy of a network in terms of the macroscopic (laboratory) state of deformation, an assumption has to be made to relate microscopic chain dimensions to macroscopic deformation. Their relation to macroscopic deformations imposed on the network has been a main area of research in the area of rubber-like elasticity. Several models have been proposed for this purpose, which are discussed in the following sections. Before that, however, we describe the macroscopic deformation, stress, and the modulus of a network.
3.3 The reduced stress and the elastic modulus The state of macroscopic deformation may be characterized by considering the deformation of a rectangular prism, with extension ratios lx, ly, lz, along the x, y,
Polymer Networks: Elastomers
345
and z directions, respectively, as lx ¼
Lx Lx0
ly ¼
Ly Ly0
lz ¼
Lz Lz0
(14)
where Lx0, Ly0, Lz0 are the sides of the prism before deformation and Lx, Ly, Lz are the corresponding sides in the deformed state. For the sake of simplicity, we consider here dry networks, that is, networks in the absence of a diluent both in the state of formation and during deformation. However, we discuss effects of swelling later in Section 6. Also, we consider only the uniaxial case. The true stress t, that is, force per unit deformed area, resulting from a uniaxial force acting on a cross-section of the network sample is obtained by the Treloar relations [5,16] " ! !# 2 @DAel 2 @DAel 1 t ¼ 2V li (15) lj @l2i @l2j T;V
where the subscript i denotes the direction of the applied uniaxial force and j denotes one of the other two directions on which only a hydrostatic pressure is acting. The expression in the brackets is evaluated at constant temperature and volume as identified by the subscripts T and V. The reader is referred to Treloar [16] and Ogden [35] for applications to other states of stress. The engineering stress s defined as the force per unit undeformed area follows from Equation (15) as t si ¼ (16) l The reduced force [ f ] is defined according to t ½ f n ¼ 2 (17) ðl l1 Þ In the limit of small deformations, the reduced force equates to the shear modulus of the sample, that is, (18) G ¼ lim f n l!1
The expressions given in this section, which are explained in more detail in Erman and Mark [34], are general expressions. In the next section, we introduce two network models that have been used in the elementary theories of elasticity to relate the microscopic deformation to the macroscopic deformation: the affine and the phantom network models.
3.4 The affine network model One of the earlier assumptions regarding microscopic deformation in networks is that the junction points in the networks move affinely (linearly) with macroscopic deformation. It follows that chain end-to-end vectors deform affinely also, and 2 2 2 x ¼ l2x x2 0 y ¼ l2y y2 0 z ¼ l2z z2 0 (19)
346
B. Erman and J.E. Mark
Substituting Equation (19) into Equation (13) in conjunction with Equation (1) leads to 1 f (20) DAel;affine ¼ xkTðl2x þ l2y þ l2z 3Þ 2 f2 A more rigorous statistical analysis [21] gives an additional volume term, mkT(V/V0) in Equation (20). This term does not appear in the simplified derivation presented here. The true stress for the uniaxial case is obtained by substituting Equation (20) into Equation (15) as f xkT 2 t¼ ðl l1 Þ (21) f 2 V0 The shear modulus Gaf of an affine network is obtained from Equations (17) and (18) as j xkT nkT ¼ (22) Gaf ¼ j 2 V0 V0 where V0 is the volume during the formation of the network.
3.5 The phantom network model The instantaneous vector r joining two junctions at the extremities of a network chain may be written as the sum of a time-averaged mean r¯ and the instantaneous fluctuation Dr from this mean, that is, r ¼ r¯ þ Dr
(23)
According to the phantom network model, the fluctuations Dr are independent of deformation and the mean r¯ deform affinely with macroscopic strain. Squaring both sides of Equation (23) and averaging overall chains gives 2 2 (24) r ¼ r¯ þ ðDrÞ2 The average of the quantity hr¯ Dri has been equated to zero in obtaining Equation (24) in as much as this quantity is equally likely to be positive or negative because of the fluctuating term Dr, and the average overall possible occurrences vanishes. Equation (24) is valid in both the deformed and undeformed states. It may be written in terms of lx, ly , and lz as ! l2x þ l2y þ l2z 2 2 r¯ 0 þ ðDrÞ2 r ¼ 3 " 2 # ! lx þ l2y þ l2z 2 2 2 ð25Þ ¼ þ r 0 1 f f 3
Polymer Networks: Elastomers
Equation (25) is obtained by use of 2 2 2 r¯ 0 ¼ 1 r 0 f 2 2 r 0 ðDrÞ2 0 ¼ f
347
ð26Þ
These two relations result from the phantom network model, as shown in derivations given elsewhere [4,25]. Using Equation (26) in Equation (25) and substituting the resulting expression into Equation (13) leads to 1 DAel;phantom ¼ xkTðl2x þ l2y þ l2z 3Þ (27) 2 Comparison of the expressions for the elastic free energies for the affine and phantom network models shows that they differ only in the front factor. Expressions for the elastic free energy of more realistic models than the affine and phantom network models are given in the following section. The true stress for the phantom network model is obtained by substituting Equation 27 into Equation 15: t¼
xkT 2 ðl l1 Þ V0
(28)
and the shear modulus Gph is obtained from Equations (17) and (18) as Gph ¼
xkT V0
(29)
Equation (29) shows that the modulus is proportional to the cycle rank x, and that no other structural parameters contribute to the modulus. The number of entanglements trapped in the network structure does not change the cycle rank. Possible contributions of these trapped entanglements to the modulus therefore cannot originate from the topology of the phantom network.
3.6 More advanced molecular theories The models presented in the previous section are of an elementary nature in the sense that they ignore contributions from intermolecular effects (such as entanglements that are permanently trapped on formation of the network). Among the theories that take account of the contribution of entanglements are (i) the treatment of Deam and Edwards [36] in terms of topological invariants, (ii) the slip-link model [37,38], (iii) the constrained-junction and constrainedchain models [39–43], and (iv) the trapped entanglement model [23,24,44]. The slip-link, constrained-junction, and constrained-chain models can be studied under a common format as can be seen from the discussion by Erman and Mark [5]. For illustrative purposes we present the constrained-junction model in some detail here. We then discuss the trapped entanglement models.
348
B. Erman and J.E. Mark
The constrained-junction model was formulated in order to explain the decrease of the elastic moduli of networks upon stretching. It was first introduced by Ronca and Allegra [39], and Flory [40]. The model assumes that the fluctuations of junctions are diminished below those of the phantom network because of the presence of entanglements and that stretching increases the range of fluctuations back to those of the phantom network. As indicated by the second part of Equation (26), the fluctuations in a phantom network are substantial. For a tetrafunctional network, the mean-square fluctuations of junctions amount to as much as half of the mean-square end-to-end vector of the network chains. The strength of the constraints on these fluctuations is measured by a parameter k, defined as ðDRÞ2 k¼ (30) ðDsÞ2 where /(DR)2S and /(Ds)2S denote, respectively, the mean-square junction fluctuations in the phantom network and in the entanglement domain. If the range of fluctuations decreases to zero because of entanglements, k becomes infinitely large. If the effect of entanglements is nil, then k ¼ 0. The k parameter is proportional to the number of junctions in the volume occupied by a given network chain. Thus, 3=2 m k ¼ I r2 0 (31) V0 where I is the constant of proportionality. For a network with tetrafunctional junctions, k may be written !3=2 1=2 N A d 3=2 r2 0 x (32) k¼I 2 V0 M where d is the density of the network and M is the molecular weight of chains between two cross-links. The elastic free energy of the constrained-junction model is given by the expression ( ) 3 3 X 1 mX 2 ½Bi þ Di lnð1 þ Bi Þ lnð1 þ Di Þ DAel ¼ xkT ðli 1Þ þ (33) 2 x i¼1 i¼1 where Bi ¼ k2 ðl2i 1Þðl2i þ kÞ
Di ¼ l2i k1 Bi
(34)
The true stress for the uniaxial case is obtained from Equations (15) and (33) as
where
xkT m 2 2 2 1 t¼ ðl l Þ þ lKðl Þ l Kðl Þ V0 x
(35)
_ þ 1Þ1 þ k1 ðl2 B_ þ BÞðB þ kl2 Þ1 Kðl2 Þ ¼ B BðB
(36)
Polymer Networks: Elastomers
@B B_ ¼ 2 ¼ B ðl2 1Þ1 2ðl2 þ kÞ1 @l The reduced force is given as n xkT m lKðl2 Þ l2 Kðl1 Þ f ¼ 1þ V0 x l l2
349
(37)
(38)
The shear modulus of the constrained-junction model is obtained in the limit of small deformations as m k2 þ 1 2 G¼ 1þ k (39) Gph x ð1 þ kÞ4 which shows that for nonzero values of the parameter k, the shear modulus of the constrained-junction model is larger than the phantom network shear modulus. For the affine limit, k-N, the shear modulus is m f Gph G¼ 1þ (40) Gph ¼ x f2 Equation (40) shows that the small deformation shear modulus of an affine network increases indefinitely over the phantom network modulus as junction functionality approaches 2. The slip-link model incorporates the effects of entanglements along the chain contour into the elastic free energy. According to the mechanism of the slip link, sketched in Figure 2, a link joins two different chains which may slide a distance a along the contour of the chains. The elastic free energy resulting from this model is ( " #) 3 3 2 X X 1 N ð1 þ ZÞl s i Ael ¼ N c kT l2i þ þ logð1 þ Zl2i Þ (41) 2 N c i¼1 1 þ Zl2i i¼1
Figure 2 Schematic drawing of a slip link, with its possible motions along the network chains specified by the distances a, and its locking into position as a cross-link.
350
B. Erman and J.E. Mark
where Nc and Ns are the number of chemical cross-links and slip links, respectively, and Z ¼ 0.2343. The first term on the right-hand side of Equation (41) is the contribution to the elastic free energy from the phantom network. The effect of entanglements enters as a further contribution and is proportional to the number of slip links. The elastic free energy of the constrained-junction model, similar to that of the slip-link model, is the sum of the phantom network free energy and that due to the constraints. Both the slip-link and the constrained-junction model free energies reduce to that of the phantom network model when the effect of entanglements diminishes to zero. One important difference between the two models, however, is that the constrained-junction model free energy equates to that of the affine network model in the limit of infinitely strong constraints, whereas the slip-link model free energy may exceed that for an affine deformation, as may be observed from Equation (41).
3.7 Contribution of trapped entanglements to the modulus As already mentioned, the cycle rank x of a network denotes the number of chains that have to be cut in order to reduce the network to a tree, and the moduli of the phantom, affine, slip-link, and constrained-junction models are all proportional to it. The cycle rank is independent of the number of trapped entanglements in the cross-linked system. A network in which chains are highly entangled has the same cycle rank as one with no entanglements. Therefore the models cited above categorically reject contributions from trapped entanglements to the modulus. However, a large body of experiments has shown that certain fraction of trapped entanglements contribute to the modulus [23,24,44]. The contributions to the modulus are given by the widely used Langley equation G ¼ Gch þ Te G0N
(42)
Here, the modulus G is given as the sum of the modulus Gch due to chemical cross-links and the trapped entanglement term TeG0N, where Te (called the ‘‘Langley trapping factor’’) is the fraction of trapped entanglements that contribute to the modulus, and G0N is the plateau modulus related to the molecular weight Me between entanglement by the expression G0N ¼
rRT Me
(43)
According to the arguments based on the constrained-junction model, the term Gch should equate to the phantom network modulus onto which contributions from entanglements are added. Experimental determinations of the contributions above those predicted by the reference phantom network model have been controversial. Experiments of Rennar and Oppermann [45] on end-linked PDMS networks, indicate that contributions from trapped entanglements are significant for low degrees of endlinking but are not important when the network chains are shorter. Experimental results of Erman et al. [46] on randomly cross-linked poly(ethyl acrylate)
Polymer Networks: Elastomers
351
networks indicate that the observed high deformation limit moduli are within the predictions of the constrained-junction model.
4. PHENOMENOLOGICAL THEORIES The elastic free energy given by the elementary and the more advanced theories are symmetric functions of the three extension ratios lx, ly , and lz. One may also express the dependence of the elastic free energy on strain in terms of three other variables, which are in turn functions of lx, ly , and lz. In phenomenological theories of continuum mechanics, where only the observed behavior of the material is of concern rather than the associated molecular deformation mechanisms, these three functions are chosen as I 1 ¼ l2x þ l2y þ l2z I 2 ¼ l2x l2y þ l2x l2z þ l2y l2z
(44)
I 3 ¼ l2x l2y l2z DAel ¼ DAel ðI 1 ; I 2 ; I 3 Þ
(45)
The most general form of the elastic free energy may be written as a power series 1 X DAel ¼ Cijk ðI 1 3Þi ðI 2 3Þ j ðI 3 1Þk (46) i;j;k¼1
where Cijk are the phenomenological coefficients. The simple case of the phantom and affine networks is obtained as the first term of the series DAel ¼ C100 ðI 1 3Þ
(47)
The elastic free energy of the so-called Mooney–Rivlin solid is obtained from Equation (46) as DAel ¼ C100 ðI 1 3Þ þ C010 ðI 2 3Þ
(48)
The reduced force follows from Equations (15) and (17) as 2C2 (49) l where C1 ¼ C100/V0 and C2 ¼ C010/V0. For large deformations, the reduced force equates to 2C1, which may be identified with the phantom network model modulus. For small deformations, 2C2 may be obtained by equating Equation (49) to Equation (39) for the constrained-junction model. Thus, ½ f n ¼ 2C1 þ
2C1 ¼ Gph m k2 þ 1 2 2C2 ¼ k Gph x ð1 þ kÞ4
(50) (51)
352
B. Erman and J.E. Mark
Further references to the phenomenological treatment may be found in Treloar [16], Ogden [35], Erman and Mark [5], and Mark [47].
5. SOME RELEVANT SIMULATIONS 5.1 Gelation The formation of network structures necessary for rubber-like elasticity has been extensively simulated by Eichinger and coworkers [48]. The basic approach is to randomly end link functionally-terminated precursor chains with a multifunctional reagent, and then to examine the sol fraction with regard to amount and types of molecules present, and the gel fraction with regard to its structure and mechanical properties (see also Chapter 2). The systems most studied in this regard [48] involve PDMS chains having end groups X that are either hydroxyl or vinyl groups, with the corresponding Y groups on the end linking agents then being either OR alkoxy groups in an organosilicate, or H atoms in a multifunctional silane [5]. There was very good agreement between theory and experiment [49]. The Monte Carlo method for simulating these reactions was used to generate additional information on the vinyl–silane end linking of PDMS [49,50]. The simulations gave a very good account of the extent of reaction at the gelation points, but overestimated the maximum extent of reaction attainable. The discrepancy may be due to experimental difficulties in taking a reaction close to completion within a highly viscous, entangled medium. If cyclic molecules of PDMS are present during the end linking, they are trapped within the network if they are large enough to be penetrated by any of the precursor chains [5]. This ‘‘incarceration’’ process has also been successfully simulated [51].
5.2 Distribution functions and stress–strain isotherms One novel approach to obtaining non-Gaussian distribution functions utilizes the wealth of information that rotational isomeric theory provides on the spatial configurations of chain molecules. Specifically, Monte Carlo calculations based on the rotational isomeric state approximation were used to simulate spatial configurations and thus distribution functions for the end-to-end separations [52]. The results obtained documented the expected fact that the Gaussian distribution is generally a very poor approximation for short chains, or for the high extensions that are of primary importance with regard to ultimate properties. Another example of this approach is to determine how an applied force can change the distributions for a chain that can undergo a coil-to-helix transition upon deformation [53]. These Monte Carlo distributions can be used in the standard three-chain model for rubber-like elasticity to generate, for example, stress–strain isotherms [5]. Non-Gaussian effects can cause large increases in modulus at high
Polymer Networks: Elastomers
353
elongations, because of the limited extensibilities of the network chains [16]. Thus, it is very useful to identify chain structures and chain lengths giving the largest increases in stress without unacceptable decreases in extensibility. This will, of course, maximize the area under the stress–strain curve, which represents the energy for rupture or toughness of the material [50]. One of the most interesting applications of this approach is to PDMS elastomers which have a bimodal distribution of network chain lengths [54] and, correspondingly, very good mechanical properties [5,27]. The upturns in modulus observed at high elongations are thought to be due to the very limited extensibilities of the short chains in the bimodal structures, with the long chains increasing extensibility, and this seems to be supported by the simulated results [52,55]. Because of the improvements in properties exhibited by elastomers having bimodal distributions [5], there have been attempts to prepare and characterize ‘‘trimodal’’ networks [56]. The calculations suggest that adding a small amount of very high molecular weight end-linkable polymer could further improve mechanical properties.
5.3 Crystallization There is now considerable interest in using simulations for characterizing crystallization in copolymeric materials. In particular, Windle and coworkers [57] have developed models capable of simulating chain ordering in copolymers composed of two comonomers, at least one of which is crystallizable. Typically, the chains are placed in parallel, two-dimensional arrangements. Neighboring chains are then searched for like-sequence matches in order to estimate extents of crystallinity. Chains stacked in arbitrary registrations are taken to model quenched (Q) samples. Annealed samples, on the other hand, are modeled by sliding the chains past one another longitudinally to search for the largest possible matching densities. The longitudinal movement of the chains relative to one another, out of register, approximately models the lateral searching (S) of sequences in copolymeric chains during annealing [50]. One example [58] of such a study involved modeling random and semiblocky poly(diphenylsiloxane-co-dimethylsiloxane) copolymers. In this example, the chains were placed alongside one another in a two-dimensional array, with black squares representing dimethylsiloxane (DMS) units and white squares representing diphenylsiloxane (DPS) units [58]. ‘‘Like’’ squares neighboring each other in the same row are then viewed as coalescing into blocks the lengths of which are under scrutiny. It is thus possible to identify crystallizable DPS regions as distinct from non-crystallizable DMS component, or units of the crystallizable DPS component that were not long enough to participate in the crystallization [58]. A value of the degree of crystallinity L of a simulated sample can then be determined by counting the units involved in the matching sequences relative to the total number of units of all the chains. The crystallites thus identified presumably act as cross-linking sites and reinforcing domains,
354
B. Erman and J.E. Mark
providing the additional toughness the semi-blocky copolymers have over their random counterparts. A similar approach was used for polypropylene (PP), a stereochemically variable hydrocarbon polymer. It is of particular interest since it can be prepared in the form of a thermoplastic elastomer in which there are alternating runs of blocks of isotactic and atactic sequences. The trick (which has been accomplished by some catalysts) is to make the isotactic runs long enough to give crystallites with enough stability to act as cross-links, without making their sizes and numbers so large that the material is highly crystalline rather than elastomeric [59,60]. Of greatest interest is the case where the isotactic lengths are kept at a constant relatively large value while the atactic sequences are increased in length, thereby decreasing the overall content [mmmm] of meso placements (replications of dextro or levo chiralities). The simulations were consistent with the presence of crystallinity at overall levels of PP isotacticity sufficiently low to give completely amorphous polymers had the structures not been blocky.
5.4 Filler reinforcement Monte Carlo computer simulations were also carried out on filled networks [50,61–63] in an attempt to obtain a better molecular interpretation of how such dispersed fillers reinforce elastomeric materials. The approach taken enabled estimation of the effect of the excluded volume of the filler particles on the network chains and on the elastic properties of the networks. In the first step, distribution functions for the end-to-end vectors of the chains were obtained by applying Monte Carlo methods to rotational isomeric state representations of the chains [64]. Conformations of chains that overlapped with any filler particle during the simulation were rejected. The resulting perturbed distributions were then used in the three-chain elasticity model [16] to obtain the desired stress– strain isotherms in elongation. In one application, a filled PDMS network was modeled as a composite of cross-linked polymer chains and spherical filler particles arranged in a regular array on a cubic lattice [65]. The filler particles were found to increase the nonGaussian behavior of the chains and to increase the moduli, as expected. It is interesting to note that composites with such structural regularity have actually been produced [66] and some of their mechanical properties have been reported [67]. In a subsequent study, the reinforcing particles were randomly distributed within the PDMS matrix [50]. One effect of the filler was to increase the extensions of the chains, at least in the case of relatively small filler particles. This is illustrated in Figure 3. These results on the distributions are in agreement with some subsequent neutron scattering experiments on silicate-filled PDMS [68]. The corresponding stress–strain isotherms in elongation are shown schematically in Figure 4. The substantial increases in stress and modulus with increase in filler content and elongation are in at least qualitative agreement with experiment. Non-spherical filler particles are also of considerable interest [50,69]. Prolate (needle-shaped) particles can be thought of as a bridge between the roughly spherical particles used to reinforce elastomers and the long fibers frequently
Polymer Networks: Elastomers
355
P(r)
Unfilled
Filled
0.0
0.0
r/rmax
Figure 3 Sketches of radial distributions for two network chains as a function of the fraction of their full extension. The presence of filler particles is seen to increase the end-to-end separation of the chain.
[f* ]
Filled
Unfilled
0.0 0.5
1/α
1.0
Figure 4 Mooney–Rivlin isotherms for the two chains described in Figure 3, showing the resulting increases in modulus due to the chains being stretched by the presence of the filler particles.
used for this purpose in thermoplastics and thermosets. Similarly, oblate (disc-shaped) particles can be considered as analogues of the much-studied clay platelets used to reinforce a variety of materials [70–73]. In the case of non-spherical particles, their orientations are also of considerable interest.
356
B. Erman and J.E. Mark
6. SWELLING OF NETWORKS AND RESPONSIVE GELS Throughout the preceding discussion, the networks were assumed to be formed in the dry state and tested in the dry state. In recent years, much emphasis has been placed on swelling of networks and their phase transitions under different activities of the network-solvent system. Large-scale volume transitions triggered by small changes in environmental variables directed attention to possible uses of swollen gels in the field of responsive materials technologies. The transition involves the gel-exuding solvent, for example, upon decrease in temperature. The resulting shrinkage (‘‘syneresis’’) is widely known as ‘‘gel collapse’’, and is shown schematically for such a temperature-induced change in Figure 5. In the following discussion, charged systems will be considered in particular because the presence of charges facilitates the volume phase transitions in swollen gels. The change in free energy of a network upon swelling is taken as the sum of the change in the elastic free energy, DAel, and the change in free energy of mixing, DAmix and the contributions from ionic groups DAi: DA ¼ DAel þ DAmix þ DAi
(52)
is where DAel may be taken as any of the expressions resulting from a model, DAmix the free energy of mixing, and DAi the contribution of the ionic groups on the chains. The total chemical potential Dm1 of solvent in the swollen network is obtained for the constrained-junction model as Dm1 1 rV 1 m V1 v2 2 2 ¼ lnð1 v2 Þ þ v2 þ wv2 þ 1 þ Kðl Þ in (53) l Mc x RT V0 N A v20 where v2 is the volume fraction of polymer, w the Flory interaction parameter, V1 the molar volume of solvent, Mc the molecular weight of a network chain, and l
Shrinkage
Wt % polymer in gel
Lightly swollen
Highly swollen Temperature
Figure 5 A gel exuding solvent upon decrease in temperature, with the shrinkage (‘‘syneresis’’) generally described as ‘‘gel collapse’’.
Polymer Networks: Elastomers
357
the extension ratio, defined for the swelling case as 1=3 V n1 V 1 þ xV 1 n2 l¼ ¼ (54) V0 V0 Here, x is the number of repeat units in one network chain, n1 the number of solvent molecules, n2 the total number of network chains in the system, i the number of ionic groups on the chains, n the number of chains, and v20 the volume fraction of chains during the formation of the network. Equating the chemical potential to zero gives a relationship between the equilibrium degree of swelling and the molecular weight Mc. The relation for Mc,ph is obtained for a tetrafunctional phantom network model as Mc;ph ¼
1=2ðrV 1 Þðv2 =v20 Þ1=3 lnð1 v2 Þ þ v2 þ wv22 inðV1 =V 0 N A Þðv2 =v20 Þ
(55)
where v2 denotes the equilibrium degree of swelling. For the affine network model, the molecular weight between cross-links Mc,af is obtained as 1=3 rV 1 v2 ðv2 =2v20 Þ (56) Mc;af ¼ lnð1 v2 Þ þ v2 þ wv22 inðV 1 =V 0 N A Þðv2 =v20 Þ Alternatively, the chemical potential expression may be solved for v2, leading to a value for the degree of swelling of the network. The result shows that the degree of swelling increases as the chain length between cross-links increases. The dominant forces that operate in swollen uncharged gels are van der Waals forces, hydrogen bonds, hydrophobic forces, and forces resulting from chain entropy. When the network chains contain ionic groups, there will be additional forces that affect their swelling properties. Translational entropy of counterions, Coulomb interactions, and ion pair multiplets are forces that lead to interesting phenomena in ion-containing gels. These phenomena were studied in detail by Khokhlov and collaborators [74–77]. The free energy of the networks used by this group is DA ¼ DAmix þ DAel þ DAtrans þ DACoulomb
(57)
where DAtrans and DACoulomb are the contributions to the elastic free energy of the networks from the translational entropy of the counterions and the free energy of Coulomb interactions. Several interesting features of gels are obtained through the use of Equation (57). A network chain of a polyampholyte gel contains both positive and negative charges. The liquid phase in the swollen polyampholyte gel may contain additional counterions. The theoretical and experimental literature on such gels was reviewed recently by Nisato and Candau [78]. In ion-containing gels, when ion-containing groups are fully dissociated the gel swells excessively, because of the tendency of the free counterions to occupy as much space as possible. In the other extreme case, called the ionomer regime, counterions are condensed on oppositely charged monomer units, forming ion pairs followed by formation of multiplets. This decreases the osmotic pressure of the gel and results
358
B. Erman and J.E. Mark
in its collapse. The conditions for ion pair formation and physical and chemical factors leading to gel swelling and collapse have been discussed by Khokhlov and Philippova [79].
7. ENTHALPIC AND ENTROPIC CONTRIBUTIONS TO RUBBER ELASTICITY: THE FORCE–TEMPERATURE RELATIONS The major component of elasticity of a network arises from the ‘‘entropic elasticity’’ of the individual chains. This was the basic assumption of the early molecular theories of rubber elasticity [5]. A closer consideration of the statistics of the single chain shows that the rotational isomeric states allowable to each torsion angle of the chain are not of the same energy, and stretching a chain or changing the temperature may move them from one isomeric minimum to a more favorable one. This results in an energetic contribution to the elasticity of a chain. Thus the total force acting on a network may be written as the sum of an entropic contribution, fs, and an energetic contribution, fe f ¼ fs þ fe
(58)
Force–temperature (‘‘thermoelastic’’) relations lead to a quantitative assessment of the relative amounts of entropic and energetic components of the elasticity of the network. In uniaxial deformation, the energetic contribution to the total elastic force [4,5,16,80–82] is given by the thermodynamically exact relation fe @ lnðf=TÞ T (59) @T f L;V The subscripts L and V denote that differentiation is performed at constant length and volume. To carry out the differentiation indicated in Equation (59), an expression for the total tensile force f is needed. One may use the expression given by Equation (28) for the phantom network model. Applying the right-hand side of Equation (59) to Equation (28) leads to f e Td ln r2 0 ¼ (60) f dT Equation (60) is important because the right-hand side relates to a microscopic quantity, /r2S0, and the left-hand side is the thermodynamic ratio of the energetic component of the force to the total force, both macroscopic quantities. It should be noted that Equation (60) is obtained by using a molecular model. Experimentally, the determination of the force at constant volume is not easy. For this reason, expressions for the force measured at constant length and pressure p or constant a and p are used. These expressions are fe @ lnðf=TÞ bT T (61) 3 @T ða f 1Þ L;p
Polymer Networks: Elastomers
Table 1
359
Some typical values for fe/f
Elastomer
fe/f
Natural rubber cis-1,4-Polybutadiene Poly(dimethylsiloxane) Elastin
0.18 0.13 0.20 0.26
fe @ lnðf=TÞ bT T @T 3 f a;p
(62)
where b is the thermal expansion coefficient of the network. It should be noted, however, that both of these equations are derived on the basis of the equation of state for simple molecular models and therefore are not quantities based purely on experimental data. Values of the energetic contribution for some typical elastomers are given in Table 1.
8. MULTIMODAL ELASTOMERS 8.1 General information The main purpose of this section is to illustrate how manipulating the distribution of network chain lengths in an elastomer can give large improvements in its mechanical properties. The preparation of such networks of controlled structures obviously requires special cross-linking reactions. In fact, a variety of ‘‘model’’ networks can now be prepared using new synthetic techniques that closely control the placements of cross-links in a network structure [5,83,84]. Specifically, end-linking functionally-terminated chains, instead of haphazardly joining chain segments at random, controls the structure of the resulting network. The functionality of a cross-link is the same as the number of functional groups on the end-linking agent. More important in the present context, the molecular weight Mc between cross-links and its distribution are the same as those of the starting chains prior to their being end linked [85–87].
8.2 Bimodal networks 8.2.1 Background With regard to elastomers of controlled structure, those having unusual distributions of network chain lengths have been of particular interest [88,89]. The most novel elastomer of this type consists of a binary combination of unusually short network chains (molecular weights of a few hundred) and the much longer chains typically associated with elastomeric behavior (molecular weights of ten or twenty thousand). Such a network is sketched in Figure 6.
360
B. Erman and J.E. Mark
Figure 6 A network having a bimodal distribution of network chain lengths. The short chains are arbitrarily shown by heavier lines than the long chains, and the dots represent the crosslinks, typically resulting from the end linking of functionally terminated chains.
As mentioned earlier, ‘‘bimodal’’ elastomers prepared by these end-linking techniques have very good ultimate properties, and for this reason there is currently much interest in preparing and characterizing such materials [88,90,91]. There is, of course, a long history of theoretical work in the area of rubber-like elasticity but almost all of it is based on monodisperse network chainlength distributions. Interest is now developing, however, in developing theoretical interpretations for the novel mechanical properties of bimodal elastomers [92–101].
8.2.2 Materials and synthetic techniques Most bimodal networks synthesized to date have been prepared from PDMS [88]. One reason for this choice is the fact that the polymer is readily available with either hydroxyl or vinyl end groups, and the reactions these groups participate in are relatively free of complicating side reactions. These ideas can obviously be extended to higher modalities (trimodal, etc., eventually approaching an extremely broad, effectively-unimodal distribution) [102–104]. The distribution of network chain lengths in a bimodal elastomer can be extremely unusual, and much different from the usual unimodal distribution obtained in less-controlled methods of cross-linking. In the important example, there is simultaneously a large number percent of short chains and a large weight percent of long chains. The major difference is the large amounts of both very short chains and very long chains in the bimodal network, which contrasts sharply with the small amounts of such chains in a typical unimodal distribution. The case where the short chains predominate numerically is of particular interest with regard to improvements in mechanical properties [5,27].
Polymer Networks: Elastomers
361
8.2.3 Elongation results The great majority of studies of mechanical properties of elastomers of any type have been carried out in elongation, because of the simplicity of this type of deformation [5,89]. In the case of the bimodal materials, many of the stress–strain isotherms in elongation were obtained on PDMS elastomers in the vicinity of 251C, a temperature sufficiently high to suppress strain-induced crystallization. The results thus determined were of considerable interest since they indicated that the bimodal nature of the distribution greatly improved the ultimate properties of the elastomer [88]. This is illustrated schematically in Figure 7, in which the data are plotted in such a way that the area under a stress–strain isotherm up to the point of failure corresponds to the energy required to rupture the network. If the network consists entirely of the short-chain component, then it is brittle (which means that the maximum extensibility is small). Similarly, if the network consists of only the long-chain component, its ultimate strength is very low. As a result, neither type of unimodal material has a large area under its stress–strain curve and, thus, neither is a tough elastomer. As can readily be seen from Figure 7, the bimodal networks are much-improved elastomers in that they can have a high ultimate strength without the usual diminished maximum extensibility. This corresponds to high values of the energy required for rupture, which makes them unusually tough elastomers, even in the unfilled state. Apparently the short chains act primarily to increase the ultimate strength through their limited deformability, while the long chains somehow thwart the spread of rupture nuclei that would otherwise lead to catastrophic failure. If true, this could be analogous to what executives like to call a ‘‘delegation of responsibilities’’. It should be pointed out that there are three requirements for obtaining these improvements. The first is that the ratio MS/ML of molecular weights of the short (MS) and long chains (ML) be very small (i.e., that their molecular weights be very different). The second is that the short chains be as short as possible; for example, a network having network chain molecular weights of 200 and 20,000 g/mol
Bimodal
f*
Short-chain unimodal
Long-chain unimodal
α
Figure 7 Typical dependence of nominal stress against elongation for two unimodal networks having either all short chains or all long chains, and a bimodal network having some of both.
362
B. Erman and J.E. Mark
would be expected to show much greater improvements from the biomodality than one having molecular weights of 2,000 and 200,000. Finally, there should be a large number concentration of the short chains, typically around 95 mol.%. Quantitative characterization of this limited chain extensibility requires, of course, a non-Gaussian distribution function [16] for the end-to-end separation r of the short network chains. One approach is based on the Fixman–Alben distribution [33], which was used [34] to calculate stress–strain isotherms in elongation for bimodal PDMS networks. Good agreement was found between theory and experiment. Other non-Gaussian distribution functions have also been successfully used for this purpose [5,105,106]. The experimental isotherms can also be interpreted using the van der Waals theory of rubber-like elasticity [5,107,108]. Another approach involves the Monte Carlo simulations described above. It utilizes the wealth of information that rotational isomeric state theory provides on the spatial configurations of chain molecules. In brief, Monte Carlo calculations based on the rotational isomeric state approximation are used to simulate spatial configurations and thus distribution functions for the end-to-end separations of the chains [20,55]. These distribution functions are then used in place of the Gaussian function in the standard three-chain model [16] in the affine limit to give the desired non-Gaussian theory of rubber-like elasticity. Stress– strain isotherms calculated in this way are strikingly similar to the experimental isotherms obtained for the bimodal networks [5,20,55]. The overall theoretical interpretations are thus quite satisfactory and would encourage other applications of these distributions, for example, to segmental orientation in networks containing very short chains. Such segmental orientation is of critical importance, for example, with regard to strain-induced crystallization. PDMS networks were found to be unsuitable for characterizing the effects of bimodality on strain-induced crystallization, because of their very low crystallization temperatures. The polymer chosen instead for these end-linked bimodal networks was poly(ethylene oxide), which has a relatively high melting point (B651C) and thus readily undergoes strain-induced crystallization [109]. The aspect of relevance here is the use of these networks to elucidate the dependence of strain-induced crystallization on network chain length distribution. Decrease in temperature was found to increase the extent to which the values of the ultimate strength of the bimodal networks exceed those of the unimodal ones [109]. These results suggest that bimodality facilitates strain-induced crystallization [5], possibly through increased orientation of the more easily crystallizable long chains, into crystallization nuclei. Similar conclusions have been reached in studies of elongated bimodal networks of poly(tetrahydrofuran) [110]. In practical terms, the above results demonstrate that short chains of limited extensibility may be bonded into a long-chain network to improve its toughness. It is also possible to achieve the converse effect. Thus, bonding a small number of relatively long elastomeric chains into a short-chain PDMS thermoset greatly improves both its energy of rupture and impact resistance [111–113]. Approximately 95 mol.% short chains give the maximum effect for the molecular weights involved. Lower concentrations give smaller improvements than can otherwise
Polymer Networks: Elastomers
363
be achieved, and higher concentrations will convert the composite from a relatively hard material into one that is more rubber-like.
8.2.4 Results in other mechanical deformations Equi-biaxial extension results have been obtained by inflating sheets of unimodal and bimodal networks of PDMS [114,115]. Upturns in the modulus were found to occur at high biaxial extensions, as expected. Also of interest, however, are pronounced maxima preceding the upturns. Such dependences represent a challenging feature to be explained by molecular theories addressed to bimodal elastomeric networks in general. In shear measurements on some unimodal and bimodal networks of PDMS [116], the bimodal PDMS networks showed large upturns in the pure-shear modulus at high strains, which were similar to those reported for elongation and biaxial extension. Tear tests have been carried out on bimodal PDMS elastomers [117–119], using the standard ‘‘trouser-leg’’ (tear strength) method. Tear energies were found to be considerably increased by the use of a bimodal distribution, with documentation of the effects of compositional changes and changes in the ratio of molecular weights of the short and long chains. The increase in tear energy did not seem to depend on tear rate [117], an important observation that seems to suggest that viscoelastic effects are not of great importance in explaining the observed improvements. A subsequent series of shear tests [118] established the dependence of the tearing properties on the composition of the bimodal networks and the lengths of the chains used to prepare them. The observed increases in strength with decreases in the molecular weight of the short chains must eventually become decreases when the chains become too short to have any elastic effectiveness at all. Some viscoelasticity results have been reported for bimodal PDMS [120], using a Rheovibron (an instrument for measuring the dynamic tensile moduli of polymers). Also, measurements have been made on permanent set for PDMS networks in compressive cyclic deformations [121]. There appeared to be less permanent set or ‘‘creep’’ in the case of the bimodal elastomers. This is consistent in a general way with some early results for polyurethane elastomers [122]. Specifically, cyclic elongation measurements on unimodal and bimodal networks indicated that the bimodal ones survived many more cycles before the occurrence of fatigue failure. The number of cycles to failure was found to be approximately an order of magnitude higher for the bimodal networks, at the same modulus at 10% deformation [5]!
8.2.5 Results of non-mechanical properties Birefringence measurements have been shown to be very sensitive to bimodality, and have therefore also been used to characterize non-Gaussian effects resulting from it in PDMS bimodal elastomers [5,123]. The freezing points of solvents absorbed into bimodal networks are also of interest since solvent molecules constrained to small volumes form only relatively small crystallites upon crystallization, and therefore exhibit lower crystallization temperatures [124–126]. Some differential scanning calorimetry (DSC) measurements on
364
B. Erman and J.E. Mark
solvent molecules constrained in the pores of PDMS elastomers gave evidence for several crystallization temperatures, which could be indicative of an unusual distribution of pore sizes. Calorimetric measurements on bimodal poly(ethylene oxide) networks indicated that the short chains seemed to decrease the amount of crystallinity in the unstretched state [127]. This is an intriguing result since they increase the extent of crystallization in the stretched state. A similar study on poly(tetrahydrofuran) did not show any decrease, however [128]. Additional insights into the dynamics and structure of bimodal elastomers have been obtained by dynamic light-scattering experiments [129], neutron scattering experiments [130] and calculations [131], dual cross-linking system experiments [132], non-affine swelling [133], and the computer simulations already mentioned.
8.2.6 Other materials in which bimodality might be advantageous There appear to be other cases where a bimodal distribution of chain length or some other physical property can be advantageous, possibly again through this idea of a ‘‘delegation of responsibilities’’ [5] (see earlier in Section 8.2.3). For example, in the area of thermosets, there seems to be an improvement in mechanical properties when the polymer being cured has a bimodal distribution of molecular weights [112]. In this case, the improvements may be due to different morphologies and degrees of inhomogeneity [113,134] resulting from the fact that the long chains in a bimodal distribution could have considerably lower solubilities than the short chains. Also, it is well known that the flow characteristics of a polymer during processing [135] can frequently be adjusted by the addition of a small amount of polymer of either very low or very high molecular weight. Another example is in the area of rubber-toughened thermoplastics in which an elastomer is dispersed as domains within the thermoplastic matrix to improve its mechanical properties [136,137]. It has been reported that a bimodal distribution of particle sizes gives the largest improvements [138–140]. Perhaps the small particles are most efficient at stopping one type of failure mechanism, and the large particles another type. In a related application, there is the possibility that a mixture of two chemically different particles, such as silica and titania [141], could have significant advantages in elastomer reinforcement, with one perhaps functioning best at moderate temperatures and the other at elevated temperatures. There is also interest in bimodal distributions of particle sizes in electrorheological fluids [142] and in stimuli-responsive films [143].
8.3 Trimodal networks 8.3.1 Experimental results Although there have been attempts to evaluate the mechanical properties of trimodal elastomers, this has not been done in any organized manner. The basic problem is the large number of variables involved, specifically three molecular weights and two independent composition variables (mol fractions); this makes it practically impossible to do an exhaustive series of relevant experiments. For this
Polymer Networks: Elastomers
365
reason, the only mechanical property experiments that have been carried out have involved arbitrarily chosen molecular weights and compositions [102,103,144]. Perhaps, not surprisingly, only modest improvements have been obtained over the bimodal materials.
8.3.2 Results from theory and simulations Some recent computational studies [92], however, indicate that it is possible to do simulations to identify those molecular weights and compositions that should maximize further improvements in mechanical properties. Such simulations are being extended to search for optimum properties of trimodal networks, specifically: (i) the elastic modulus, (ii) maximum extensibility, (iii) tensile strength, and (iv) segmental orientability. Results to date [56] suggest that a trimodal network prepared by incorporating small numbers of very long chains into a bimodal network of long and short chains could have significantly improved ultimate properties.
9. LIQUID–CRYSTALLINE ELASTOMERS 9.1 General information In the phrase ‘‘liquid–crystalline’’, the ‘‘crystalline’’ adjective refers to the fact that these materials are sufficiently ordered to diffract an X-ray beam in a way analogous to that of normal crystalline materials. On the other hand, the ‘‘liquid’’ part specifies that there is frequently sufficient disorder for the material to flow like a liquid [145]. The disorder is typically in one dimension as is the case, for example, with rod-like molecules having their axes all parallel but out of register with regard to their lengths. Both low molecular weight materials [145] and polymers [146,147] can show liquid crystallinity. In the case of polymers, it frequently occurs in very stiff chains such as the Kevlarss and other aromatic polyamides. It can also occur with flexible chains, however, and it is these flexible chains in the elastomeric state that are the focus of the present discussion. One reason such liquid– crystalline elastomers are of particular interest is the fact that (i) they can be extensively deformed (as described for elastomers throughout this chapter), (ii) the deformation produces alignment of the chains, and (iii) alignment of the chains is central to the formation of liquid–crystalline phases. Because of fascinating properties related to their novel structures, liquid–crystalline elastomers have been the subject of numerous studies, as described in several detailed reviews [148–150]. The purpose here will be to mention some typical elastomers exhibiting liquid crystallinity, to describe some of their properties, and to provide interpretations of some of these properties in molecular terms. The types of liquid–crystalline phases of interest can be defined by the direction describing the preferred orientation (see Chapter 8). The limits are the usual completely ordered (crystalline) and completely disordered (isotropic) phases, with a nematic liquid–crystalline phase (‘‘mesophase’’) between them.
366
B. Erman and J.E. Mark
Figure 8 Liquid–crystalline polymers in which the mesomorphic sequences occur in the sidechain (middle), in the chain backbone (top), or in both (bottom) (‘‘combination’’ structures).
The oriented parts can be entire molecules in the case of low molecular weight compounds, but only sequences along the chain backbone in the case of polymers. In the nematic case, the disorder is the already-mentioned sliding of segments relative to one another to place them out of register. There are also a variety of smectic liquid–crystalline phases, in which layers of molecules or chain sequences occur in layers that are disordered relative to one another. In contrast, cholesteric phases have layers of nematic arrangements that are stacked in rotated arrangements, and a similar stacking occurs in the case of the discotics. In the case of polymers, there can be liquid–crystalline arrangements that involve the side chains attached to the chain backbones. Figure 8 illustrates the three possibilities: groups that can form liquid–crystalline phases occurring in the backbones, in the side chains, and in both (in what are called ‘‘combination’’ structures) [20]. In the case of the side-chain structures, the length of the ‘‘spacer’’ connecting the group to the backbone is of great importance.
9.2 Main-Chain liquid–crystalline elastomers 9.2.1 Poly(diethylsiloxane) The polymer in this category that has been the most studied is poly(diethylsiloxane) (PDES) [–Si(OC2H5)2O–]n. Of greatest interest has been its formation of nematic liquid–crystalline phases, and relevant studies have covered a wide variety of its properties [20]. These studies have included structural changes during transitions [151], effects of stretching on the transitions [152], mechanical properties in general [153], characterization using atomic force microscopy (AFM) [154] or X-ray diffraction [155], and responses of guest chains in deformed PDES elastomers [156].
Polymer Networks: Elastomers
367
One item of great interest with regard to these materials is the temperature at which the nematic liquid–crystalline phase becomes isotropic. Such isotropization (‘‘clearing’’) temperatures Ti have been reported for a variety of symmetric polysiloxanes polymers having repeat units [Si((CH2)mCH3)2–O–][20]. PDES elastomers show values of Ti that significantly decrease with decrease in molecular weight. In fact, the liquid–crystalline phase does not form at all if M is below approximately 25,000 g/mol. This is in sharp contrast to the behavior of low molecular weight liquid–crystalline molecules; many cholesterol molecules that show mesophases have molecular weights down in the hundreds [145]. Since stretching a PDES aligns the chains in the direction of the liquid– crystalline structures, the values of Ti should also increase with elongation, and this is indeed found to be the case [157].
9.2.2 Other acyclic polysiloxanes Symmetric polysiloxanes having m ¼ 29 have also been investigated, with some properties listed in several articles in a handbook [158], and elsewhere [20]. The isotropization temperatures reported in these studies show a very interesting increase with increase in the number m of methylene groups in the side chains [159]. As one interesting example, the results indicate that the predicted value of Ti for PDMS lies below its value of Tm (melt temperature). This means that PDMS does not show a liquid–crystalline phase because it crystallizes before it gets to the lower temperature required. Another interesting feature pertains to the melting points cited for the polymers having m ¼ 6–9. The side chains are now long enough to crystallize themselves, which is apparently the reason that formation of mesophases is suppressed. Such side-chain crystallization has also been involved in polysilane homopolymers [160], and chemical copolymers of polyethylene [161,162], the so-called linear lowdensity polyethylenes (see Chapter 4). In any case, such crystallization presumably could also interfere with formation of the mesophases that might otherwise occur.
9.2.3 Some polysiloxanes with cyclic groups in the backbone Polysiloxanes in this category typically contain cyclics of –Si(CH3)2–O– siloxane units of various sizes, or such siloxane units mixed with some carbosiloxanes (with additional –CH2– sequences) [163–165]. The cyclic portions can add considerable stiffness, resulting in isotropization temperatures above the polymers’ decomposition temperatures.
9.2.4 Polyphosphazenes A number of polyphosphazenes of repeat unit [–PRRuN–] also exhibit liquid– crystalline phases [166–168]. It is certainly intriguing that apparently the only classes of flexible chains that extensively exhibit liquid–crystalline phases are the polysiloxane and polyphosphazene semi-inorganic polymers.
9.2.5 Some mechanical properties in elongation One aspect of this type of behavior involves the already mentioned increase in the isotropization temperatures with increase in elongation [169–171]. Also of
368
B. Erman and J.E. Mark
Lowest
f
High
Lower
0 α
Figure 9 Illustrative stress–strain isotherms for poly(diethylsiloxane), as a function of the amount of mesophase present.
importance, of course, are the stress–strain isotherms themselves. Some obtained for PDES as a function of degree of mesomorphic structure are shown schematically in Figure 9 [152]. The curves show yield points akin to those shown by partially crystalline polymers, and the overall shapes of the curve differ greatly with decrease in the amounts of mesophase present, either present initially or induced by the deformation. As is generally the case, formation of a second phase leads to irreversibility in the stress–strain isotherms [152]. The larger the elongation during the deformation, the larger the irreversibility (hysteresis) upon completing the retraction part of the cycle.
9.3 Side-Chain liquid–crystalline elastomers 9.3.1 Some general aspects In this category, the units giving rise to the liquid–crystalline behavior can be in the backbone (as already discussed), in the side chains, or in both [172]. Of considerable interest is the orientation of the mesogenic groups and the chain backbones to which they are attached [173,174]. Frequently-studied backbones include siloxanes and acrylates [175,176], but a variety of other structures have also been studied, including amphiphilics [177]. The side chains in these structures can rearrange into positions either parallel or perpendicular to the deformed chain backbone. [178]. The outcome depends particularly on the nature and length of the flexible spacer connecting the mesogenic groups to the chain backbone. As expected the physical properties can become strongly anisotropic [179]. It has been long known that some liquid–crystalline materials of this type could be oriented by imposing an electric or magnetic field [180]. The chains
Polymer Networks: Elastomers
369
could also be aligned when these liquid–crystalline elastomers are deformed (generally in elongation but also in some cases in compression), and then crosslinked into network structures. The major focus in these experiments was how the mechanical deformation affected the nature of the mesophase (in particular its axial direction relative to the direction of the strain), and its isotropization temperature. The studies generally involved measurements of both stress and birefringence as a function of strain, and the ratio of the former to the latter (the ‘‘stress-optical coefficient’’). The mesogenic behavior of such networks obviously depends strongly on their structures. For example, the effects of degree of cross-linking, and composition in the case of copolymers, have been documented [181]. The phase transitions depend significantly on spacer length, as has been demonstrated, for example, for oligo-oxyethylene spacers [182]. Closer coupling between the mesogenic groups and the polymer backbone tends to make the system more sensitive to the mechanical deformation, at least in the case of methylene groups making up the spacer [183]. Cross-linking can generally be induced by gamma radiation or chemical means [184], and it has been observed that relatively high degrees of crosslinking can be introduced without destroying the liquid crystallinity [185]. Infrared (IR) spectroscopy and stress–strain measurements in extension indicated that relatively low strains may frequently induce significant organization. One relevant experiment involved two cross-linking procedures: the first cross-linking produced a network in which the mesogenic units could be oriented [186], while the second subsequently locked in the network anisotropy. Samples were found to be clear and to have X-ray diffraction patterns characteristic of a highlyordered nematic material. Also of interest was the fact that transitions from the isotropic phase to the nematic phase caused significant increases in length. Using one or two cross-linking agents in the presence of a magnetic field could also be used to prepare ‘‘Monodomain’’ nematics (in which the director alignment is claimed to be macroscopically uniform) [187]. The thermoelastic behavior of these materials has also been reported [188]. Such experiments resolve the nematic to isotropic transition into entropic and enthalpic contributions as already described, and provides values of the corresponding energetic and entropic parts of the force, fe and fs [175] (see Section 7).
9.3.2 Discotic, cholesteric, and smectic elastomers Considerably less work has been done on discotic liquid–crystalline elastomers [189,190] and cholesteric elastomers [191]. The same seems to be true for smectic elastomers [192,193], even though some of them have the additional interesting property of being chiral [194,195].
9.3.3 Ferroelectric and piezoelectric elastomers In addition, some liquid–crystalline elastomers are ferroelectric (possess spontaneous electric polarization) [196,197], or piezoelectric (become electrically
370
B. Erman and J.E. Mark
polarized when mechanically strained, and become mechanically strained when exposed to an electric field) [198,199].
9.3.4 Photonic elastomers Finally, some liquid–crystalline elastomers exhibit interesting photonic effects [200,201]. Of particular importance are non-linear optical properties. These involve interactions of light with the elastomer in a way that some of the characteristics of the incident light change, specifically its phase or frequency (including frequency doubling or frequency mixing) [202,203].
9.4 Theory As would not be surprising, given the unusual properties cited in this overview, liquid–crystalline elastomers have been the focus of numerous theoretical investigations [148–150,204–207]. These theoretical treatments extend over a wide range of sophistication and rigor. The simplest physical picture of nematic elasticity can be visualized by the lattice theory, in which semi-flexible chains are assumed to be embedded in an isotropic lattice of solvent molecules. The semiflexible chains consist of rods of m freely jointed segments of length l, which determines their stiffness. Stretching of the chains orients the segments in a way that increases strongly with increasing stiffness of the chains. Calculations based on a lattice model [205] show an abrupt jump in the segmental orientation function at a finite stretch ratio, and this corresponds to the isotropic-nematic transition. Below the transition, the sample behaves close to isotropic Gaussian elasticity. At a fixed uniaxial force, the transition is marked by a sudden elongation, resulting from the abrupt alignment of the segments along the direction of the force during the transition. Above the transition point the segments are highly oriented along the direction of stretch, and the network is nematic.
10. NOVEL REINFORCED ELASTOMERS 10.1 Sol–Gel in-situ precipitated ceramic particles Some elucidation of the mechanism of elastomer reinforcement is being obtained by precipitating chemically-generated fillers into network structures rather than blending badly agglomerated filler particles into elastomers prior to their crosslinking. This has been done for a variety of fillers, for example, silica by hydrolysis of organosilicates, titania from titanates, alumina from aluminates, etc. [85–87]. A typical, and important, reaction is the acid- or base-catalyzed hydrolysis of tetraethylorthosilicate: SiðOC2 H5 Þ4 þ 2H2 O ! SiO2 þ 4C2 H5 OH
(63)
Reactions of this type are much used by the ceramists in the new sol–gel chemical route to high-performance ceramics [208]. In the ceramics area itself, the
Polymer Networks: Elastomers
371
advantages are the possibility of using low temperatures, increased purity of the products, control of ultrastructure (at the nanometer level), and relative ease of forming ceramic alloys. In the elastomer-reinforcement area, the advantages include the avoidance of the difficult, time-consuming, and energy-intensive process of blending agglomerated filler into high molecular weight (highviscosity) polymer, and the ease of obtaining extremely good dispersions. In the simplest approach to obtaining elastomer reinforcement, some of the organometallic material is absorbed into the cross-linked network, and the swollen sample placed into water containing the catalyst, typically a volatile base such as ammonia or ethylamine [4,5,209–211]. Hydrolysis to form the desired silica-like particles proceeds rapidly at room temperature to yield the order of 50 wt.% filler in less than an hour. The particles formed are generally approximately spherical, and are well dispersed and essentially unagglomerated, which suggests that the sol–gel reaction within the elastomer may involve simple homogeneous nucleation. This is consistent with the fact that particles growing independently of one another and separated by cross-linked polymer would not agglomerate unless very high concentrations were reached. The particles appear to have a relatively narrow size distribution, with almost all of them having ˚. diameters in the range 200–300 A Such in-situ generated particles can increase the modulus by more than an order of magnitude, and the stress–strain isotherms show the upturns at high elongation that are the signature of good reinforcement [212]. As generally occurs in filled elastomers, there is considerable irreversibility in the isotherms, which is thought to be due to irrecoverable sliding of the chains over the surfaces of the filler particles. If the hydrolyses in organosilicate-polymer systems are carried out with increased amounts of the silicate, bicontinuous phases can be obtained (with the silica and polymer phases interpenetrating one another) [213]. At still-higher concentrations of the silicate, the silica generated becomes the continuous phase, with the polymer dispersed in it. The result is a polymer-modified ceramic, variously called an ‘‘ORMOCER’’ [214,215], ‘‘CERAMER’’ [216,217], or ‘‘POLYCERAM’’ [218,219]. It is obviously of considerable importance to determine how the elastomeric phase modifies the ceramic in which it is dispersed. The hardness of PDMS-SiO2 composites of this type can be varied greatly by changing the ratio of organic-to-inorganic character, as measured by the molar ratio of organic R groups to Si atoms. Low values of the R/Si ratio yield a brittle ceramic, and high values yield a reinforced elastomer. The most interesting range of R/Si values, in the vicinity of unity, gives a hybrid material that can be viewed as either a ceramic of reduced brittleness or an elastomer of increased hardness, depending on one’s point of view.
10.2 Non-Spherical particles Reinforcing fillers can be deformed from their usual approximately spherical shapes in a number of ways. For example, if the particles are a glassy polymer such as polystyrene (PS), then deforming the matrix in which they reside at a
372
B. Erman and J.E. Mark
Figure 10 Deformation of spherical filler particles into prolate (needle-shaped) ellipsoids; see text for details.
temperature above the glass transition temperature of PS will convert them into ellipsoids. This is illustrated in Figure 10. Uniaxial deformations give prolate (needle-shaped) ellipsoids, and biaxial deformations give oblate (disc-shaped) ellipsoids [220,221]. Prolate particles can be thought of as a conceptual bridge between the roughly spherical particles used to reinforce elastomers and the long fibers frequently used for this purpose in thermoplastics and thermosets. Similarly, oblate particles can be considered as analogues of the much-studied clay platelets used to reinforce a variety of materials [70–73], but with dimensions that are controllable. In the case of nonspherical particles, their orientations are also of considerable importance. One interest here is the anisotropic reinforcements such particles provide, and there have been simulations to better understand the mechanical properties of such composites [86,222].
10.3 Magnetic particles Incorporating reinforcing particles that respond to a magnetic field is important with regard to aligning the particles to improve mechanical properties anisotropically [223–226]. In related work, some in-situ techniques have been used to generate electrically conducting fillers such as polyaniline within an elastomeric material [227].
10.4 Layered fillers Exfoliating layered particles such as the clays, mica, or graphite is being used to provide very effective reinforcement of elastomers at loading levels much smaller than in the case of solid particles such as carbon black and silica [228–231]. Other properties can also be substantially improved, including increased resistance to solvents, and reduced permeability and flammability.
10.5 Polyhedral oligomeric silsesquioxanes (POSS) These fillers are cage-like silicon–oxygen structures, and have been called the smallest possible silica particles. The most common structure has eight
Polymer Networks: Elastomers
373
silicon atoms, each carrying an organic group. The particles on which none of the groups are functionally reactive can be simply blended into elastomers using the usual mixing or compounding procedures. In this case, the groups are chosen to improve miscibility with the elastomeric host matrix. In contrast, those particles having one reactive functional group can be attached to a polymer as side chains. Those with two reactive groups can be incorporated into polymer backbones by copolymerization, and those with more than two can be used for forming cross-linked networks [232–236].
10.6 Nanotubes Carbon nanotubes are also of considerable interest with regard to both reinforcement and possible increases in electrical conductivity [237–239]. There is considerable interest in characterizing the flexibility of these nanotube structures, in minimizing their tendencies to aggregate, and in maximizing their miscibilities with organic and inorganic polymers.
10.7 Porous fillers Some fillers such as zeolites are sufficiently porous to accommodate monomers, which can then be polymerized. This threads the chains through the cavities, with unusually intimate interactions between the reinforcing phase and the host elastomeric matrix [238,240], as is illustrated in Figure 11. Unusually good reinforcement is generally obtained. Also, because of the constraints imposed by the cavity walls, these confined polymers frequently show no glass transition temperatures or melting points [86,241].
10.8 Fillers with controlled interfaces By choosing the appropriate chemical structures, chains that span filler particles in a polymer-based composite can be designed so that they are either durable, breakable irreversibly, or breakable reversibly [242–245].
Figure 11 Schematic of threading polymer chains through a cavity by polymerizing monomer absorbed into a zeolite.
374
B. Erman and J.E. Mark
11. FURTHER COMMENTS ON SOME CHARACTERIZATION TECHNIQUES 11.1 Optical and spectroscopic techniques An example of a relevant optical property is the birefringence of a deformed polymer network [246]. This strain-induced birefringence can be used to characterize segmental orientation, both Gaussian and non-Gaussian elasticity, and to obtain new insights into the network chain orientation (see Chapter 8) necessary for strain-induced crystallization [4,16,85,247,248]. IR dichroism has also been particularly helpful in this regard. Of predominant interest is the orientation factor S (1/2)(3/cos2bS1) (see Chapter 8), which can be obtained experimentally from the ratio of absorbances of a chosen peak parallel and perpendicular to the direction in which an elastomer is stretched [5,249]. One representation of such results is the effect of network chain length on the reduced orientation factor [S] S/(l2l1), where l is the elongation. A comparison is made among typical theoretical results in which the affine model assumes the chain dimensions to change linearly with the imposed macroscopic strain, and the phantom model allows for junction fluctuations that make the relationship nonlinear. The experimental results were found to be close to the phantom relationship. Combined techniques, such as Fourier-transform infrared (FTIR) spectroscopy combined with rheometry (see Chapter 8), are also of increasing interest [250]. Other optical and spectroscopic techniques are also important, particularly with regard to segmental orientation. Some examples are fluorescence polarization, deuterium nuclear magnetic resonance (NMR), and polarized IR spectroscopy [4,246,251]. Also relevant here is some work indicating that microwave techniques can be used to image elastomeric materials, for example, with regard to internal damage [252,253].
11.2 Microscopies A great deal of information is now being obtained on crystallinity, filler dispersion, and other aspects of elastomer structure and morphology by scanning probe microscopy, which consists of several approaches [254–256]. One approach is that of scanning tunneling microscopy (STM), in which an extremely sharp metal tip on a cantilever is passed along the surface being characterized while measuring the electric current flowing through quantum mechanical tunneling. Monitoring the current then permits maintaining the probe at a fixed height above the surface, and display of probe height as a function of surface coordinates then gives the desired topographic map. One limitation of this approach is the obvious requirement that the sample be electrically conductive. AFM, on the other hand, does not require a conducting surface. The probe simply responds to attractions and repulsions from the surface, and its corresponding downward and upward motions are directly recorded to give
Polymer Networks: Elastomers
375
the relief map of the surface structure. The probe can be either in contact with the surface, or adjacent to it and sensing only Coulombic or van der Waals forces. There are numerous other types of scanning probe microscopy, including electrochemical STM and AFM, frictional force microscopy, surface force compliance, magnetic force microscopy, electric force microscopy, scanning thermal microscopy, and near-field scanning optical microscopy (NSOM). Some of these various techniques not only generate topographic relief images, but also provide the opportunity to transport separate individual atoms and molecules into nanoscale arrangements [85]. An example of an application to elastomers is the characterization of binodal and spinodal phase-separated structures occurring in model PDMS networks [257–259]. Another application of these microscopy devices involves attaching probes to the two ends of a single polymer chain and then stretching it to determine its equilibrium and dynamic mechanical properties. This is generally referred to as ‘‘single molecule elasticity’’ [260–264]. Some rather sophisticated equipment is required, such as ‘‘optical tweezers’’, and sensitive force-measuring devices. Most of the effort thus far has involved biopolymers, and mechanicallyinduced transitions between their various conformations. Although such studies are obviously not relevant to the many unresolved issues that involve the interactions of chains within an elastomeric network, they are certainly of interest in their own right.
11.3 NMR Solid-state NMR methods have been much used to study the characteristics of the network chains themselves, particularly with regard to orientations [265], molecular motions [266], and their effects on the diffusion of small molecules [267]. Aspects related to the structures of the networks include the degree of cross-linking [268,269], the distributions of cross-links [270] and stresses [271], and topologies [272,273]. Another example is the use of NMR to clarify some issues in the areas of aging and phase separation [274]. Most elastomers require reinforcing fillers to function effectively, and NMR has been used to characterize the structures of such composites as well. Examples are the adsorption of chains onto filler surfaces [275], the immobilization of these chains into ‘‘bound rubber’’ [276], and the imaging of the filler itself [277].
11.4 Small-Angle scattering The technique of this type of greatest utility in the study of elastomers is smallangle neutron scattering (SANS), for example, from deuterated chains in a nondeuterated host [278–280]. One application has been the determination of the degree of randomness of the chain configurations in the undeformed state, an issue of importance with regard to the basic postulates of elasticity theory described earlier. Of even greater importance is determination of the manner in which the dimensions of the chains follow the macroscopic dimensions of the sample, that is, the degree of affineness of the deformation. This relationship
376
B. Erman and J.E. Mark
Sensor 1 Excitation
Pulse amplitude
Δt
Sensor 2
Time t, secs
Figure 12 Pulse propagation results, showing measurement of the time Wt required for a pulse to pass downward through an elastomer from Sensor 1 to Sensor 2.
between the microscopic and macroscopic levels in an elastomer is one of the central problems in rubber-like elasticity. Some small-angle X-ray scattering (SAXS) techniques have also been applied to elastomers. Examples are the characterization of fillers precipitated into elastomers, and the corresponding incorporation of elastomers into ceramic matrices, in both cases to improve mechanical properties [4,85,213].
11.5 Brillouin scattering The application of Brillouin scattering to the characterization of elastomers [281–283] is an interesting extension of earlier work on polymers in general [284–287]. It should be quite useful for looking at glassy-state properties of elastomers at very high frequencies.
11.6 Pulse propagation One example of a relatively new technique for the non-invasive, non-destructive characterization of network structures involves pulse-propagation measurements [288,289]. In this technique, the delay Dt in a pulse passing through the network is used to obtain information on the network structure, for example, the chain length between cross-links or between entanglements. The technique is illustrated schematically in Figure 12 [282].
ACKNOWLEDGEMENT It is a pleasure to acknowledge the financial support provided JEM by the National Science Foundation through Grant DMR-0314760 (Polymers Program, Division of Materials Research).
Polymer Networks: Elastomers
377
REFERENCES 1 F. Ignatz-Hoover and B.H. To, Vulcanization. In: B. Rodgers (Ed.), Rubber Compounding: Chemistry and Applications, Marcel Dekker, New York, 2004, p. 505. 2 A.Y. Coran, Vulcanization. In: J.E. Mark and B. Erman (Eds.), Science and Technology of Rubber, Elsevier, Amsterdam, 2005. 3 S.S. Labana and R.A. Dickie (Eds.), Characterization of Highly Cross-Linked Polymers, American Chemical Society, Washington, DC, 1984. 4 J.E. Mark and B. Erman, Rubberlike Elasticity: A Molecular Primer, Wiley-Interscience, New York, 1988. 5 B. Erman and J.E. Mark, Structures and Properties of Rubberlike Networks, Oxford University Press, New York, 1997. 6 J.E. Mark, The rubber elastic state. In: J.E. Mark, K.L. Ngai, W.W. Graessley, L. Mandelkern, E.T. Samulski, J.L. Koenig and G.D. Wignall, Physical Properties of Polymers, 3rd ed., Cambridge University Press, Cambridge, 2004, p. 3. 7 B. Erman and J.E. Mark, The molecular basis of rubberlike elasticity. In: J.E. Mark, B. Erman and F.R. Eirich (Eds.), Science and Technology of Rubber, Academic, San Diego, 2005, p. 157. 8 J.E. Mark, J. Chem. Educ., 79 (2002) 1437. 9 J.E. Mark, J. Phys. Chem. Part B, 107 (2003) 903. 10 A.N. Gent (Ed.), Engineering with Rubber: How to Design Rubber Components, Hanser Publishers, New York, 1992. 11 E. Guth and H.M. James, Ind. Eng. Chem., 33 (1941) 624. 12 F.T. Wall, J. Chem. Phys., 10 (1942) 485. 13 P.J. Flory, J. Chem. Phys., 10 (1942) 51. 14 P.J. Flory and J. Rehner, J. Chem. Phys., 11 (1943) 512. 15 P.J. Flory and J. Rehner, J. Chem. Phys., 11 (1943) 521. 16 L.R.G. Treloar, The Physics of Rubber Elasticity, Clarendon Press, Oxford, 1975. 17 W. Burchard and S.B. Ross-Murphy (Eds.), Physical Networks: Polymers and Gels, Elsevier, London, 1990. 18 S.B. Ross-Murphy, Polymer, 33 (1992) 2622. 19 G.M. Kavanagh and S.B. Ross-Murphy, Prog. Polym. Sci., 23 (1998) 533. 20 J.E. Mark and B. Erman, Rubberlike Elasticity: A Molecular Primer, 2nd ed., Cambridge University Press, Cambridge, 2006. 21 P.J. Flory, Principles of Polymer Chemistry, Cornell University Press, Ithaca, NY, 1953. 22 P.J. Flory and B. Erman, Macromolecules, 15 (1982) 800. 23 W.W. Graessley, Adv. Polym. Sci., 47 (1982) 67. 24 W.W. Graessley, Polymeric Liquids and Networks: Structure and Properties, Garland Science, New York, 2003. 25 P.J. Flory, Proc. R. Soc. London A, 351 (1976) 351. 26 J.E. Mark, Brit. Polym. J., 17 (1985) 144. 27 J.E. Mark, Macromol. Symp., St. Petersburg issue, 191 (2003) 121. 28 P.J. Flory, Statistical Mechanics of Chain Molecules, Interscience, New York, 1969. 29 W.L. Mattice and U.W. Suter, Conformational Theory of Large Molecules: The Rotational Isomeric State Model in Macromolecular Systems, Wiley, New York, 1994. 30 M. Rehahn, W.L. Mattice and U.W. Suter, Adv. Polym. Sci., 131/132 (1997) 1. 31 P.J. Flory and D.Y. Yoon, J. Chem. Phys., 61 (1974) 5358. 32 D.Y. Yoon and P.J. Flory, J. Chem. Phys., 61 (1974) 5366. 33 M. Fixman and R. Alben, J. Chem. Phys., 58 (1973) 1553. 34 B. Erman and J.E. Mark, J. Chem. Phys., 89 (1988) 3314. 35 R.W. Ogden, Nonlinear Elastic Deformations, Dover Publications, New York, 1997. 36 R.T. Deam and S.F. Edwards, Philos. Trans. R. Soc. Lond. A, 280 (1976) 317. 37 R.C. Ball, M. Doi and S.F. Edwards, Polymer, 22 (1981) 1010. 38 S.F. Edwards and T.A. Vilgis, Polymer, 27 (1986) 483. 39 G. Ronca and G. Allegra, J. Chem. Phys., 63 (1975) 4990. 40 P.J. Flory, J. Phys. Chem., 66 (1977) 5720.
378
41 42 43 44 45 46 47 48 49 50 51 52
53 54 55 56 57 58 59 60 61 62 63
64 65 66
67 68 69 70
71
72 73 74 75 76 77
B. Erman and J.E. Mark
A. Kloczkowski, J.E. Mark and B. Erman, Macromolecules, 28 (1995) 5089. A. Kloczkowski, J.E. Mark and B. Erman, Comput. Polym. Sci., 5 (1995) 37. B. Erman and L. Monnerie, Macromolecules, 22 (1989) 3342. N.R. Langley, Macromolecules, 1 (1968) 348. N. Rennar and W. Oppermann, Coll. Polym. Sci., 270 (1992) 527. B. Erman, W. Wagner and P.J. Flory, Macromolecules, 13 (1980) 1554. J.E. Mark, J. Polym. Sci. Part C, 31 (1970) 97. B.E. Eichinger and O. Akgiray, Computer simulation of polymer network formation. In: E.A. Colbourne Longman (Ed.), Computer Simulation of Polymers, White Plains, NY, 1994, p. 263. J.L. Braun, J.E. Mark and B.E. Eichinger, Macromolecules, 35 (2002) 5273. J.E. Mark, Makromol. Symp., 171 (2001) 1. L.C. DeBolt and J.E. Mark, Macromolecules, 20 (1987) 2369. J.E. Mark, Simulations of networks and elastomeric properties. In: M. Doyama, J. Kihara, M. Tanaka and R. Yamamoto (Eds.), Computer Aided Innovation of New Materials II, Elsevier, Amsterdam, 1993. J.G. Curro, K.S. Schweizer, D. Adolf and J.E. Mark, Macromolecules, 19 (1986) 1739. J.E. Mark, Makromol. Chemie, Suppl., 2 (1979) 87. J.G. Curro and J.E. Mark, J. Chem. Phys., 80 (1984) 4521. B. Erman and J.E. Mark, Macromolecules, 31 (1998) 3099. S. Hanna and A.H. Windle, Polymer, 29 (1988) 207. T.M. Madkour and J.E. Mark, Comput. Polym. Sci., 4 (1994) 87. H.-H. Brintzinger, D. Fischer, R. Mulhaupt, B. Reiger and R.M. Waymouth, Angew. Chem. Int. Ed. Engl., 34 (1995) 1143. T.M. Madkour and J.E. Mark, J. Polym. Sci., Polym. Phys. Ed., 35 (1997) 2757. J.E. Mark, J. Comput.-Aided Mats. Design, 3 (1996) 311. Q.W. Yuan, A. Kloczkowski, J.E. Mark and M.A. Sharaf, J. Polym. Sci., Polym. Phys. Ed., 34 (1996) 1647. J.E. Mark, Illustrative modeling studies on elastomers and rubberlike elasticity. In: M. Laudon, and B. Romanowiczs (Eds.), International Conference on Computational Nanoscience. Computational Publications, Boston, Hilton Head Island, SC, 2001, p. 53. J.E. Mark and J.G. Curro, J. Chem. Phys., 79 (1983) 5705. M.A. Sharaf, A. Kloczkowski and J.E. Mark, Comput. Polym. Sci., 4 (1994) 29. H.B. Sunkara, J.M. Jethmalani and W.T. Ford, Solidification of colloidal crystals of Silica. In: J.E. Mark, C.Y.-C. Lee and P.A. Bianconi (Eds.), Hybrid Organic–Inorganic Composites, American Chemical Society, Washington, 1995, Vol. 585, p. 181. Z. Pu, J.E. Mark, J.M. Jethmalani and W.T. Ford, Chem. Mater., 9 (1997) 2442. A.I. Nakatani, W. Chen, R.G. Schmidt, G.V. Gordon and C.C. Han, Polymer, 42 (2001) 3713. M.A. Sharaf, A. Kloczkowski and J.E. Mark, Comput. Theor. Polym. Sci., 11 (2001) 251. A. Okada, M. Kawasumi, A. Usuki, Y. Kojima, T. Kurauchi and O. Kamigaito, Nylon 6-clay hybrid. In: D.W. Schaefer and J.E. Mark (Eds.), Polymer-Based Molecular Composites, , Materials Research Society, Pittsburgh, 1990, Vol. 171, p. 45. T.J. Pinnavaia, T. Lan, Z. Wang, H. Shi and P.D. Kaviratna, Clay-reinforced epoxy nanocomposites: Synthesis, properties, and mechanism of formation. In: G.-M. Chow and K.E. Gonsalves (Eds.), Nanotechnology: Molecularly Designed Materials, American Chemical Society, Washington, 1996, Vol. 622, p. 250. E.P. Giannelis, Organoceramic nanocomposites. In: S. Mann (Ed.), Biomimetic Materials Chemistry, VCH Publishers, New York, 1996, p. 337. R.A. Vaia and E.P. Giannelis, Polymer, 42 (2001) 1281. Y. Osada and A.R. Khokhlov (Eds.), Polymer Gels and Networks, Marcel Dekker, New York, 2002. O.E. Philippova, Polym. Sci. C., 42 (2000) 208. A.R. Khokhlov, In: K. Dusek (Ed.), Responsive Gels: Volume Transitions I., Springer Verlag, Berlin, 1992, p. 125. A.R. Khokhlov and O.E. Philippova. In: S. Webber (Ed.), Solvents and Self-Organization of Polymers. Kluwer Academic Publishers, Dordrecht, The Netherlands, 1996, p. 197.
Polymer Networks: Elastomers
379
78 G. Nisato and S.J. Candau, In: Y. Osada and A.R. Khokhlov (Eds.), Polymer Gels and Networks, Marcel Dekker, New York, 2002, p. 131. 79 A.R. Khokhlov and O.E. Philippova, In: Y. Osada and A.R. Khokhlov (Eds.), Polymer Gels and Networks, Marcel Dekker, New York, 2002, p. 163. 80 J.E. Mark, Rubber Chem. Technol., 46 (1973) 593. 81 P.J. Flory, Trans. Faraday Soc., 57 (1961) 829. 82 P.J. Flory, A. Ciferri and C.A.J. Hoeve, J. Polym. Sci., 45 (1960) 235. 83 J.E. Mark and B. Erman, Molecular aspects of rubber-like elasticity. In: R.F.T. Stepto (Ed.), Polymer Networks, Blackie Academic, Chapman & Hall, Glasgow, 1998. 84 J.E. Mark and B. Erman, Elastomers and rubber-like elasticity. In: W. Brostow (Ed.), Performance of Plastics, Hanser, Cincinnati, 2001, p. 401. 85 J.E. Mark, Prog. Polym. Sci., 28 (2003) 1205. 86 J.E. Mark, Macromol. Symp., Kyoto issue, 201 (2003) 77. 87 J.E. Mark, Molec. Cryst. Liq. Cryst., Bucharest Meeting, 417 (2004) 75. 88 J.E. Mark, Rubber Chem. Technol., 72 (1999) 465. 89 J.E. Mark, Thermoset elastomers. In: C.D. Craver and C.E. Carraher, Jr. (Eds.), Applied Polymer Science-21st Century, American Chemical Society, Washington, 2000, p. 209. 90 K. Urayama, T. Kawamura, Y. Hirata and S. Kohjiya, Polymer, 39 (1998) 3827. 91 J.E. Mark, Improved elastomers through control of network chain-length distributions. In: P.N. Prasad, J.E. Mark, S.H. Kandil and Z.H. Kafafi (Eds.), Science and Technology of Polymers and Advanced Materials, Plenum, New York, 1998, p. 85. 92 G. Sakrak, I. Bahar and B. Erman, Macromol. Theory Simul., 3 (1994) 151. 93 V.V. Vasilevskaya and A.N. Semenov, Polym. Sci. U.S.S.R, 36 (1994) 1535. 94 I. Bahar, B. Erman, L. Bokobza and L. Monnerie, Macromolecules, 28 (1995) 225. 95 C. Hagn, M. Wittkop, S. Kreitmeier, H.L. Trautenberg, T. Holzl and D. Goritz, Polym. Gels Networks, 5 (1997) 327. 96 P. Sotta, Macromolecules, 31 (1998) 8417. 97 P.R. von Lockette and E.M. Arruda, Macromolecules, 32 (1999) 1990. 98 W. Michalke, S. Kreitmeier, M. Lang, A. Buchner and D. Goritz, Comp. Theor. Polym. Sci., 11 (2001) 459. 99 P.R. von Lockette and E.M. Arruda, Comp. Theor. Polym. Sci., 11 (2001) 415. 100 P.R. von Lockette, E.M. Arruda and Y. Wang, Macromolecules, 35 (2002) 7100. 101 L.-X. Zhang, Z.-T. Jiang and D.-I. Zhao, J. Polym. Sci., Polym. Phys., 40 (2002) 105. 102 T. Madkour and J.E. Mark, Polym. Bull., 31 (1993) 615. 103 T. Madkour and J.E. Mark, J. Macromol. Sci., Macromol. Rep., A31 (1994) 153. 104 B.D. Viers and J.E. Mark, Research (Unpublished results). 105 M.A. Llorente, A.M. Rubio and J.J. Freire, Macromolecules, 17 (1984) 2307. 106 C. Menduina, J.J. Freire, M.A. Llorente and T. Vilgis, Macromolecules, 19 (1986) 1212. 107 H.-G. Kilian, Coll. Polym. Sci., 259 (1981) 1151. 108 H.-G. Kilian, Private Communication, 1990. 109 C.-C. Sun and J.E. Mark, J. Polym. Sci., Polym. Phys. Ed., 25 (1987) 2073. 110 A. Hanyu and R.S. Stein, Macromol. Symp., 45 (1991) 189. 111 M.-Y. Tang, A. Letton and J.E. Mark, Coll. Polym. Sci., 262 (1984) 990. 112 G.A. Holmes and A. Letton, Polym. Eng. Sci., 34 (1994) 1635. 113 N.C.B. Tan, B.J. Bauer, J. Plestil, J.D. Barnes, D. Liu, L. Matejka, K. Dusek and W.L. Wu, Polymer, 40 (1999) 4603. 114 P. Xu and J.E. Mark, J. Polym. Sci., Polym. Phys. Ed., 29 (1991) 355. 115 P. Xu and J.E. Mark, Polymer, 33 (1992) 1843. 116 S. Wang and J.E. Mark, J. Polym. Sci., Polym. Phys. Ed., 30 (1992) 801. 117 L.C. Yanyo and F.N. Kelley, Rubber Chem. Technol., 60 (1987) 78. 118 T.L. Smith, B. Haidar and J.L. Hedrick, Rubber Chem. Technol., 63 (1990) 256. 119 G.B. Shah, Macromol. Chem. Phys., 197 (1996) 2201. 120 A.L. Andrady, M.A. Llorente and J.E. Mark, Polym. Bull., 26 (1991) 357. 121 J. Wen, J.E. Mark and J.J. Fitzgerald, J. Macromol. Sci., Macromol. Rep., A31 (1994) 429.
380
B. Erman and J.E. Mark
122 Y. Kaneko, Y. Watanabe, T. Okamoto, Y. Iseda and T. Matsunaga, J. Appl. Polym. Sci., 25 (1980) 2467. 123 V. Galiatsatos, R.O. Neaffer, S. Sen and B.J. Sherman, Refractive index, stress optical coefficient, and optical configuration parameter of polymers. In: J.E. Mark (Ed.), Physical Properties of Polymers Handbook, Springer-Verlag, New York, 1996, p. 535. 124 C.L. Jackson and G.B. McKenna, J. Non-Cryst. Solids, 131–133 (1991) 221. 125 A.N. Goldstein, C.M. Esher and A.P. Alivisatos, Science, 256 (1992) 1425 and pertinent references cited therein. 126 J.H.A. Grobler and W.J. McGill, J. Polym. Sci., Polym. Phys. Ed., 31 (1993) 575. 127 S.J. Clarson, J.E. Mark, C.-C. Sun and K. Dodgson, Eur. Polym. J., 28 (1992) 823. 128 C.M. Roland and G.S. Buckley, Rubber Chem. Technol., 64 (1991) 74. 129 H. Oikawa, Polymer, 33 (1992) 1116. 130 A.-M. Hecht, F. Horkay and E. Geissler, J. Phys. Chem., 105 (2001) 5637. 131 A. Kloczkowski, J.E. Mark and B. Erman, Macromolecules, 24 (1991) 3266. 132 T. Madkour and R.A. Azzam, Polymer, 47 (2006) 415. 133 J.-U. Sommer and S. Lay, Macromolecules, 35 (2002) 9832. 134 W.-L. Wu, J.-T. Hu and D.L. Hunston, Polym. Eng. Sci., 30 (1990) 835. 135 J.D. Ferry, Viscoelastic Properties of Polymers, Wiley, New York, 1980. 136 C.B. Bucknall, Toughened Plastics, Applied Science Press, London, 1977. 137 A.M. Donald and E.J. Kramer, J. Appl. Polym. Sci., 27 (1982) 3729. 138 T.K. Chen and Y.H. Jan, J. Mats. Sci., 27 (1992) 111. 139 Y. Okamoto, H. Miyagi, M. Kakugo and K. Takahashi, Macromolecules, 24 (1991) 5639. 140 M. Demirors, Preprints, Div. Polym. Mat., Am. Chem. Soc., 79 (1998) 162. 141 J. Wen and J.E. Mark, J. Appl. Polym. Sci., 58 (1995) 1135. 142 J.-B. Jun, S.-U. Uhm, S.-H. Cho and K.-D. Suh, Langmuir, 20 (2004) 2429. 143 D.J. Lestage, D.J. Scheis and M.W. Urban, Langmuir, 20 (2004) 7027. 144 G.T. Burns, unpublished results, Dow Corning Corporation, 1995. 145 P.J. Collings, Liquid Crystals: Nature’s Delicate Phase of Matter, Princeton University Press, Princeton, 1990. 146 A. Ciferri (Ed.), Liquid Crystallinity in Polymers: Principles and Fundamental Properties, VCH Publishers, New York, 1991. 147 A.M. Donald and A.H. Windle, Liquid–Crystalline Polymers, Cambridge University Press, Cambridge, UK, 1992. 148 G.G. Barclay and C.K. Ober, Prog. Polym. Sci., 18 (1993) 899. 149 M. Warner and E.M. Terentjev, Prog. Polym. Sci., 21 (1996) 853. 150 M. Warner and E.M. Terentjev, Liquid Crystal Elastomers, Oxford University Press, New York, 2003. 151 K.J. Miller, J. Grebowicz, J.P. Wesson and B. Wunderlich, Macromolecules, 23 (1990) 849. 152 V.S. Papkov, A.A. Turetskii, G.J.J. Out and M. Moller, Int. J. Polym. Mat., 51 (2002) 369. 153 Y.K. Godovsky, Angew. Macromol. Chemie, 202/203 (1992) 187. 154 Y.K. Godovsky, V.S. Papkov and S.N. Magonov, Macromolecules, 34 (2001) 976. 155 K. Inomata, K. Yamamoto and T. Nose, Polym. J., 32 (2000) 1044. 156 A. Batra, R.C. Hedden, P. Schofield, A. Barnes, C. Cohen and T.M. Duncan, Macromolecules, 36 (2003) 9458. 157 Y.K. Godovsky and L.A. Valetskaya, Polym. Bull., 27 (1991) 221. 158 Y.K. Godovsky and V.S. Papkov, Polysiloxane mesophases. In: J.E. Mark (Ed.), Polymer Data Handbook, Oxford University Press, New York, 1999, p. 394. 159 Y.K. Godovsky, N.N. Makarova, V.S. Papkov and N.N. Kuzmin, Makromol. Chem., 6 (1985) 443. 160 M.J. Winokur and R. West, Macromolecules, 36 (2003) 7338. 161 J. Wagner and P.J. Phillips, Polymer, 42 (2001) 8999. 162 X.-B. Zhang, Z.-S. Li, Z.-Y. Lu and C.-C. Sun, Macromolecules, 35 (2002) 106. 163 G.H.F. Bergmann, H. Finkelmann, V. Percec and M. Zhao, Makromol. Rapid Commun., 18 (1997) 353. 164 S.I. Belousov, A.I. Buzin and Y.K. Godovsky, Polym. Sci. U. S. S. R., 41 (1999) 303. 165 Y.K. Godovsky, S.I. Belousov, N.N. Makarova, G. Brezesinski, H. Mohwald, T.R. Jensen and K. Kjaer, Nonlinear Opt. Quantum Opt., 31 (2004) 31.
Polymer Networks: Elastomers
381
166 M. Cypryk, K. Matyjaszewski, M. Kojima and J.H. Magill, Makromol. Chem., Rapid Commun., 13 (1992) 39. 167 T. Miyata, T. Masuko, M. Kojima and J.H. Magill, Makromol. Chem. Phys., 195 (1994) 253. 168 M. Kojima, J.H. Magill, U. Franz, M.L. White and K. Matyjaszewski, Makromol. Chem. Phys., 196 (1995) 1739. 169 S. Disch, C. Schmidt and H. Finkelmann, Makromol. Rapid Commun., 15 (1994) 303. 170 J. Kupfer and H. Finkelmann, Makromol. Chem. Phys., 195 (1994) 1353. 171 I. Kundler and H. Finkelmann, Makromol. Rapid Commun., 16 (1995) 679. 172 R. Zentel and G. Reckert, Makromol. Chem., 187 (1986) 1915. 173 E. Anglaret, M. Brunet, B. Desbat, P. Keller and T. Buffeteau, Macromolecules, 38 (2005) 4799. 174 M. Tammer, J. Li, A. Komp, H. Finkelmann and F. Kremer, Makromol. Chem. Phys., 206 (2005) 709. 175 D.K. Shenoy, D.L. Thomsen, P. Keller and B.R. Ratna, J. Phys. Chem., 107 (2003) 13755. 176 P.-P. Gilles, J.-C. Milano and J.-L. Vernet, Macromol. Chem. Phys., 204 (2003) 2222. 177 P. Fischer, C. Schmidt and H. Finkelmann, Makromol. Rapid Commun., 16 (1995) 435. 178 R. Zentel and M. Benalia, Makromol. Chem., 188 (1987) 665. 179 K. Hammerschmidt and H. Finkelmann, Makromol. Chem., 190 (1989) 1089. 180 H. Finkelmann, H.-J. Kock, W. Gleim and G. Rehage, Makromol. Rapid Commun., 5 (1984) 287. 181 G.R. Mitchell, F.J. Davis and A. Ashman, Polymer, 28 (1987) 639. 182 V. Percec and C.-S. Hsu, Polym. Bull., 23 (1990) 463. 183 W. Kaufhold, H. Finkelmann and H.R. Brand, Makromol. Chem., 192 (1991) 2555. 184 E.R. Zubarev, R.V. Talroze, T.I. Yuranova, V.N. Vasilets and N.A. Plate, Makromol. Rapid Commun., 17 (1996) 43. 185 F.J. Davis, A. Gilbert, J. Mann and G.R. Mitchell, J. Polym. Sci., Polym. Chem., 28 (1990) 1455. 186 J. Kupfer and H. Finkelmann, Makromol. Rapid Commun., 12 (1991) 717. 187 D. Lacey, H.N. Beattie, G.R. Mitchell and J.A. Pople, J. Mats. Chem., 8 (1998) 53. 188 R.V. Talroze, T.I. Gubina, V.P. Shibaev and N.A. Plate, Makromol. Rapid Commun., 11 (1990) 67. 189 H. Bengs, H. Finkelmann, J. Kupfer, H. Ringsdorf and P. Schuhmacher, Makromol. Rapid Commun., 14 (1993) 445. 190 S. Disch, H. Finkelmann, H. Ringsdorf and P. Schuhmacher, Macromolecules, 28 (1995) 2424. 191 Y.-G. Jia, B.-Y. Zhang, Q.-J. Sun and H.-X. Chang, Coll. Polym. Sci., 282 (2004) 1077. 192 X.-Z. He, B.-Y. Zhang, L.-J. Xiao, Y. Wang and H.-Q. Wu, J. Appl. Polym. Sci., 97 (2005) 498. 193 P. Beyer and R. Zentel, Macromol. Rapid Commun., 26 (2005) 874. 194 R. Zentel, G. Reckert, S. Bualek and H. Kapitza, Makromol. Chem., 190 (1989) 2869. 195 K. Semmler and H. Finkelmann, Makromol. Chem. Phys., 196 (1995) 3197. 196 R. Zentel and M. Brehmer, CHEMTECH, 25(5) (1995) 41. 197 F. Kremer, H. Skupin, W. Lehmann, E. Gebhardt and R. Zentel, Makromol. Symp., 175 (2001) 247. 198 J.H. Wendorff, Angew.Chem. Int. Ed. Eng., 30 (1991) 405. 199 H. Hirschmann, W. Meier and H. Finkelmann, Makromol. Chem., Rapid Commun., 13 (1992) 385. 200 W. Gleim and H. Finkelmann, Makromol. Chem., 188 (1987) 1489. 201 M. Warner and E.M. Terentjev, Macromol. Symp., 200 (2003) 81. 202 I. Benne, K. Semmler and H. Finkelmann, Makromol. Rapid Commun., 15 (1994) 295. 203 I. Benne, K. Semmler and H. Finkelmann, Macromolecules, 28 (1995) 1854. 204 H.R. Brand, Makromol. Chem., Rapid Commun., 10 (1989) 57. 205 B. Erman, I. Bahar, A. Kloczkowski and J.E. Mark, Macromolecules, 23 (1990) 5335. 206 Y. Yang, A. Kloczkowski, J.E. Mark, B. Erman and I. Bahar, Macromolecules, 28 (1995) 4920. 207 X.-J. Wang and M. Warner, Macromol. Theory Simul., 6 (1997) 37. 208 C.J. Brinker, E.P. Giannelis, R.M. Laine and C. Sanchez (Eds.), Better Ceramics Through Chemistry VIII: Hybrid Materials, Vol. 519, Materials Research Society, Warrendale, PA, 1998, 209 J.E. Mark, CHEMTECH, 19 (1989) 230. 210 J.E. Mark and D.W. Schaefer, Reinforcement of elastomers by the in-situ generation of filler particles. In: D.W. Schaefer and J.E. Mark (Eds.), Polymer-Based Molecular Composites, Materials Research Society, Pittsburgh, 1990, Vol. 171, p. 51. 211 T. Liu, C. Burger and B. Chu, Prog. Polym. Sci., 28 (2003) 5. 212 J.E. Mark and Y.-P. Ning, Polym. Bull., 12 (1984) 413.
382
B. Erman and J.E. Mark
213 D.W. Schaefer, J.E. Mark, D.W. McCarthy, L. Jian, C.-C. Sun and B. Farago, Structure of microphase-separated silica/siloxane molecular composites. In: D.W. Schaefer and J.E. Mark (Eds.), Polymer-Based Molecular Composites, , Materials Research Society, Pittsburgh, 1990, Vol. 171, p. 57. 214 H. Schmidt and H. Wolter, J. Non-Cryst. Solids, 121 (1990) 428. 215 R. Nass, E. Arpac, W. Glaubitt and H. Schmidt, J. Non-Cryst. Solids, 121 (1990) 370. 216 G.L. Wilkes, H.-H. Huang and R.H. Glaser, New inorganic–organic hybrid materials through the sol–gel approach. In: J.M. Zeigler and F.W.G. Fearon (Eds.), Silicon-Based Polymer Science: A Comprehensive Resource, American Chemical Society, Washington, DC, 1990, Vol. 224, p. 207. 217 A.B. Brennan, B. Wang, D.E. Rodrigues and G.L. Wilkes, J. Inorg. Organomet. Polym., 1 (1991) 167. 218 W.F. Doyle, B.D. Fabes, J.C. Root, K.D. Simmons, Y.M. Chiang and D.R. Uhlmann, PTFE-Silicate composites via sol-gel processes. In: J.D. Mackenzie and D.R. Ulrich (Eds.), Ultrastructure Processing of Advanced Ceramics, Wiley-Interscience, New York, 1988, p. 953. 219 D.R. Uhlmann, B.J.J. Zelinski, G. Teowee, J.M. Boulton and A. Koussa, J. Non-Cryst. Solids, 129 (1991) 76. 220 S. Wang and J.E. Mark, Macromolecules, 23 (1990) 4288. 221 S. Wang, P. Xu and J.E. Mark, Macromolecules, 24 (1991) 6037. 222 M.A. Sharaf and J.E. Mark, Polymer, 43 (2002) 643. 223 Z. Rigbi and J.E. Mark, J. Polym. Sci., Polym. Phys. Ed., 23 (1985) 1267. 224 C.A. Sobon, H.K. Bowen, A. Broad and P.D. Calvert, J. Mat. Sci. Lett., 6 (1987) 901. 225 G.B. Sohoni and J.E. Mark, J. Appl. Polym. Sci., 34 (1987) 2853. 226 P. Calvert and A. Broad, Biomimetic routes to magnetic iron oxide-polymer composites. In: K.L. Mittal (Ed.), Polymers in Information Storage Technology, Plenum Press, New York, 1991, p. 257. 227 S. Murugesan, G.S. Sur, G. Beaucage and J.E. Mark, Silicon Chem., 2 (2005) 217. 228 E.P. Giannelis, R. Krishnamoorti and E. Manias, Adv. Polym. Sci., 138 (1999) 107. 229 R.A. Vaia and E.P. Giannelis, MRS Bull., 26(5) (2001) 394. 230 T.J. Pinnavaia and G. Beall (Eds.), Polymer-Clay Nanocomposites, Wiley, New York, 2001. 231 Y.T. Vu, J.E. Mark, L.H. Pham and M. Engelhardt, J. Appl. Polym. Sci., 82 (2001) 1391. 232 J.D. Lichtenhan, J. Schwab and W.A. Reinerth, Sr., Chem. Innov., 31 (2001) 3. 233 R.M. Laine, J. Choi and I. Lee, Adv. Mats., 13 (2001) 800. 234 D.A. Loy, C.R. Baugher, D.A. Schnieder, A. Sanchez and F. Gonzalez, Polym. Preprints, 42(1) (2001) 180. 235 K.J. Shea and D.A. Loy, MRS Bull., 26 (2001) 368. 236 T.S. Haddad, A. Lee and S.H. Phillips, Polym. Preprints, 42(1) (2001) 88. 237 H. Nakamura and Y. Matsui, J. Am. Chem. Soc., 117 (1995) 2651. 238 H.L. Frisch and J.E. Mark, Chem. Mater., 8 (1996) 1735. 239 S.J. Tans, M.H. Devoret, H. Dai, A. Thess, R.E. Smalley, L.J. Geerligs and C. Dekker, Nature, 386 (1997) 474. 240 G. Kickelbick, Prog. Polym. Sci., 28 (2003) 83. 241 G.S. Sur, H. Sun, T.J. Lee, S.G. Lyu and J.E. Mark, Coll. Polym. Sci., 281 (2003) 1040. 242 B.T.N. Vu, J.E. Mark and D.W. Schaefer, Preprints, Am. Chem. Soc. Div. Polym. Mat.: Sci. Eng., 83 (2000) 411. 243 B.T.N. Vu, Interfacial Modification for the Reinforcement of Silicone Elastomer Composites. M. S. Thesis in Chemistry, The University of Cincinnati, 2001. 244 D.W. Schaefer, B.T.N. Vu and J.E. Mark, Rubber Chem. Technol., 75 (2002) 795. 245 B.T.N. Vu, J.E. Mark and D.W. Schaefer, Composite Interfaces, 10 (2003) 451. 246 B. Erman and J.E. Mark, Ann. Rev. Phys. Chem., 40 (1989) 351. 247 L. Bokobza, F. Cle´ment, L. Monnerie and P. Lapersonne, IR dichroism and birefringence. In: K. te Nijenhuis and W.J. Mijs (Eds.), The Wiley Polymer Networks Group Review Series, Vol. 1. Wiley, New York, 1998, p. 321, Chapter 24. 248 L. Bokobza and N. Nugay, J. Appl. Polym. Sci., 81 (2001) 215. 249 S. Besbes, I. Cermelli, L. Bokobza, L. Monnerie, I. Bahar, B. Erman and J. Herz, Macromolecules, 25 (1992) 1949. 250 J.L. Leblanc, Rubber Chem. Technol., 78 (2005) 54. 251 I. Noda, A.E. Dowrey and C. Marcott, Characterization of polymers using polarizationmodulation infrared techniques: Dynamic infrared linear dichroism (DIRLD) spectroscopy.
Polymer Networks: Elastomers
252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267
268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289
383
In: H. Ishida (Ed.), Fourier Transform Infrared Characterization of Polymers, Plenum Press, New York, 1987, p. 33. W.C. Fitzgerald, M.N. Davis, J.L. Blackshire, J.F. Maguire and D.B. Mast, J. Corrosion Sci. Eng., 3 (2002) 15. S. McClellan, D.B. Mast, W.J. van Ooij, L. Nikiel and M. Gerspacher, research in progress. D.A. Bonnell (Ed.), Scanning Probe Microscopy and Spectroscopy: Theory, Techniques, and Applications, Springer, Berlin, 2001. A.D. Stefanis and A.A.G. Tomlinson, Scanning Probe Microscopies: From Surface Structure to NanoScale Engineering, Trans Tech Publications Ltd., Uetikon-Zurich, 2001. H.R. Allcock, F.W. Lampe and J.E. Mark, Contemporary Polymer Chemistry, 3rd ed., Prentice Hall, Englewood Cliffs, NJ, 2003. B.D. Viers, S. Sukumaran, G. Beaucage and J.E. Mark, Polym. Preprints, 38(2) (1997) 333. B.D. Viers and J.E. Mark, Polym. Preprints, 39(1) (1998) 520. B.D. Viers, Ph. D. Thesis in Chemistry: On the Supramolecular Structure in Model PDMS Elastomers. The University of Cincinnati, 1998. S. Chu, Science, 253 (1991) 861. S.B. Smith, Y. Cui and C. Bustamante, Science, 271 (1996) 795. H. Li, M. Rief, F. Oesterhelt and H.E. Gaub, Adv. Mater., 3 (1998) 316. C. Ortiz and G. Hadziioannou, Macromolecules, 32 (1999) 780. A. Janshoff, M. Neitzert, Y. Oberdorfer and H. Fuchs, Angew. Chem. Int. Ed., 39 (2000) 3213. V.M. Litvinov, Macromolecules, 34 (2001) 8468. V.M. Litvinov and H.W. Spiess, Macromol. Chem., 192 (1991) 3005. L. Garrido, J.L. Ackerman and J.E. Mark, Self-diffusion of poly(dimethylsiloxane) chains. In: L.-H. Lee (Ed.), New Trends in Physics and Physical Chemistry of Polymers, Plenum, New York, 1989, p. 355. G.I. Sandakov, L.P. Smirnov, A.I. Sosikov, K.T. Summanen and N.N. Volkova, J. Polym. Sci., Polym. Phys. Ed., 32 (1994) 1585. M. Garbarczyk, F. Grinberg, N. Nestle and W. Kuhn, J. Polym. Sci., Polym. Phys., 39 (2001) 2207. V.M. Litvinov and A.A. Dias, Macromolecules, 34 (2001) 4051. M. Schneider, D.E. Demco and B. Blumich, Macromolecules, 34 (2001) 4019. K. Beshah, J.E. Mark and J.L. Ackerman, Macromolecules, 19 (1986) 2194. L.P. Smirnov, Polym. Sci. U. S. S. R., 42 (2000) 1775. P. Blumler and B. Blumich, Macromolecules, 24 (1991) 2183. J.P. Cohen-Addad, NMR approach to siloxane properties: Melts, gels, silica mixtures. In: S.J. Clarson and J.A. Semlyen (Eds.), Siloxane Polymers, Prentice Hall, Englewood Cliffs, 1993, p. 511. V.M. Litvinov, H. Barthel and J. Weis, Macromolecules, 35 (2002) 4356. L. Garrido, J.E. Mark, S. Wang, J.L. Ackerman and J.M. Vevea, Polymer, 33 (1992) 1826. J.S. Higgins and H. Benoit, Neutron Scattering from Polymers, Clarendon Press, Oxford, 1994. G.D. Wignall, Neutron and X-ray scattering. In: J.E. Mark (Ed.), Physical Properties of Polymers Handbook, Springer-Verlag, New York, 1996, p. 299. R.-J. Roe, Methods of X-ray and Neutron Scattering in Polymer Science, Oxford University Press, Oxford, 2000. S.H. Anders, H.H. Krbecek and M. Pietralla, J. Polym. Sci., Polym. Phys. Ed., 35 (1997) 1661. M. Sinha, Ph. D. Physics: Probing Polymer Networks Using Pulse Propagation and Brillouin Light Scattering Techniques. University of Cincinnati, 2000. M. Sinha, J.E. Mark, H.E. Jackson and D. Walton, J. Chem. Phys., 117 (2002) 2968. G.D. Patterson, J. Polym. Sci., Polym. Phys. Ed., 35 (1977) 455. T. Sakurai, T. Matsuoka, S. Koda and H. Nomura, J. Appl. Polym. Sci., 76 (2000) 978. A. Kisliuk, V.N. Novikov and A.P. Sokolov, J. Polym. Sci., Polym. Phys. Ed., 40 (2001) 201. S.H. Anders, R. Eberle, L. Peetz, J.-K. Kruger, U. Goschel and M. Pietralla, J. Polym. Sci., Polym. Phys. Ed., 40 (2002) 1201. A.N. Gent and P. Marteny, J. Appl. Phys., 53 (1982) 6069. M. Sinha, B. Erman, J.E. Mark, T.H. Ridgway and H.E. Jackson, Macromolecules, 36 (2003) 6127.
This page intentionally left blank
SECTION IV: Polymer Degradation
This page intentionally left blank
CHAPT ER
10 Polymer Degradation and Oxidation: An Introduction John M. Chalmers and Robert J. Meier
Contents
1. Introduction 2. Standard Tests and Comparative Methods 2.1 Oxidative-induction time 2.2 Oxygen uptake 2.3 Carbonyl index 2.4 Wet chemistry/titration/staining 2.5 Melt flow index 3. Spectroscopic Techniques 3.1 Mid-Infrared spectroscopy 3.2 Raman spectroscopy 3.3 UV/fluorescence/phosphorescence/visible spectroscopy 3.4 Mass spectrometry 3.5 Nuclear magnetic resonance spectroscopy 3.6 X-ray photoelectron spectroscopy and secondary ion mass spectrometry 4. Thermal Methods 4.1 Differential scanning calorimetry 4.2 Differential photocalorimetry 4.3 Thermogravimetric analysis 5. Chromatographic Analysis 5.1 Gas chromatography 5.2 Liquid chromatography 6. Closing Remarks Acknowledgement References
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00410-8
388 390 390 393 394 397 399 402 402 414 418 422 429 433 436 436 438 438 442 442 443 447 448 448
r 2008 Elsevier B.V. All rights reserved.
387
388
John M. Chalmers and Robert J. Meier
1. INTRODUCTION As co-editors of this book, as with other chapters in this book, we would have liked to have featured a single chapter dealing with this specialised, important and very wide application area, but this proved difficult to realise because of the specialism of many of the researchers and practitioners in this field. So, as a compromise, we eventually commissioned two specific chapters detailing investigations using perhaps two of the less well-routinely publicised techniques, especially within industry; these are chemiluminescence (CL) and electron spin resonance (ESR), which are very well covered in the next two chapters and will therefore not be mentioned in this chapter, unless forming part of a multitechnique study. So this relatively concise chapter will provide an introduction to the molecular characterisation and analysis of the degradation and oxidation of polymers, and aim to provide information that complements the next two chapters. Reference sources on polymer degradation and oxidation are extensive and diverse, and most contain methods of molecular characterisation and analysis. Many cited in this chapter appear in the specialist journal Polymer Degradation and Stability (published by Elsevier Science B.V.). This chapter will not be a comprehensive review, but rather provide the reader with a snapshot of applications of many of the varied testing techniques or analytical tools that are brought to bear on investigating, studying and monitoring of the effects of polymer property and structure deterioration and alteration occurring as a consequence of degradation and oxidation mechanisms. The number of references in this chapter is also very far from exhaustive, examples having been selected merely to indicate an application type or area and most have been chosen from relatively recent publications; full referencing can be traced readily through the references cited within these references. Degradation means different things to different people: the polymer chemist might focus predominantly on the mechanisms of attack on and subsequent breakup of the polymer chain; the fabricator might recognise it initially through gel formation or processing properties; the consumer will likely complain about such as product discoloration, smell or increasing brittleness. Of course, these property changes and consequence are almost always interlinked. The properties of thermoplastic polymers are essentially the properties of long chains and so degradation can have a potentially profound effect. Polymer chains can be susceptible to breakage by a variety of mechanisms. Degradation can be oxidative, shear-induced, hydrolytic, by thermal scission, or by radiation attack from UV or other sources, or combinations of these or indeed other mechanisms. Chains may become oxidised; they may ‘unzip’, as, for example in the dehydrochlorination of poly(vinyl chloride) (PVC); or they may lose side groups. Each of these degradation processes impacts on the polymer properties (affecting such as processing conditions, mechanical performance, etc.) and product aesthetics (colour, smell, etc.). Degradation can be confined essentially to the surface of a polymer product, or it can be spread throughout the bulk. Usually the polymer chain is broken leading to smaller fragments. One or both of these ‘broken’ chain fragments may remain active long enough to take place in further reaction. The activity can be terminated internally leading to a shorter version of the original chain but with a different end grouping. It may also be possible for a still-active
Polymer Degradation and Oxidation: An Introduction
389
fragment to recombine with the main chain leading to a new permanent covalent bond. This may actually lead to a chain extension if the functionality at the chain end is favourable. A further alternative is that the active fragment may attack the main chain somewhere along its length resulting in a branched structure. If this happens repeatedly it may lead to hyperbranching and ultimately cross-linking. A useful concise source to a collective description of the processes of oxidative degradation of polymers and coverage of the analytical tools used to investigate and measure them is Chapter 14 in Ref. [1]. This reference also discusses the limitations of many of the techniques, and contains a more extensive list of references. In the discussions that follow, many of the application examples cited were undertaken using a variety of analytical techniques and tests, as is the norm, but for convenience here we have categorised them so that we may highlight application of a particular technique or methodology. In the descriptions of the examples, out of necessity, often only scant details are given in order to give a flavour of the investigation and technique used; of course, more complete details will be found within the cited reference(s). The natural tolerances of both surface and bulk properties are sometimes tested by such as outdoors weathering. However, the effectiveness of stabilisers and antioxidants in many polymer formulations means that in order to realistically evaluate their performance, accelerated ageing tests must be applied. The oldest and probably the most reliable thermal method is oven ageing. For outdoor applications the stability of polymers and polymer formulations must be assessed for against exposure to sunlight, UV radiation, etc., and for certain applications, for example some medical products or products to be used in harsh environments, it is also important to know how polymers behave in the presence of various other radiation sources, e.g., g-radiation from Co60. Although the majority of studies focus on the solid state, many applications focus more or additionally on the volatile products arising from polymer degradation. Evolved gas analysis (EGA) from thermal analysers and pyrolysers by spectroscopic and coupled chromatography–spectroscopy techniques can be particularly important from a safety and hazard viewpoint, since data from such measurements can be used to predict toxic or polluting gases from fires, incinerators, etc. Measuring the relative oxidative stability of polymers is important. Measurements can be used to determine dependencies on structural and molecular weight/weight distribution or the effectiveness of an antioxidant, or to perhaps assess the amount present in a polymer sample, etc. The preferred and commonest method consists in raising the sample temperature to a predetermined level, while in an inert atmosphere, then switching the atmosphere to air or oxygen. The time to the onset of exothermic reaction is measured. The measurement methods outlined in this chapter begin with what can be described as essentially comparative tests, many of them standard practices in common usage; the discussion then moves on to the role of spectroscopic methods in characterising degradation mechanisms and comparing relative levels of degradation, primarily in bulk samples; this is followed with a section covering the more surface-specific spectroscopic techniques; the chapter closes with, in sequence, discussions related specifically to thermal methods and chromatographic techniques, respectively.
390
John M. Chalmers and Robert J. Meier
2. STANDARD TESTS AND COMPARATIVE METHODS 2.1 Oxidative-induction time The oxidative-induction time/oxidation induction time (OIT) test is described in standard test methods ISO 11357-6 [2] and ASTM D3895 [3]. OIT is expressed as the time to onset of oxidation in a polymer test sample exposed to oxygen [1,4]. The method was developed to specifically analyse polyolefin resins that are in a fully stabilised/compounded form. The method involves heating a polymer sample in a differential scanning calorimetry (DSC) instrument. The sample is heated in an open DSC pan under a purge of nitrogen gas from 501C to a test temperature (typically 2001C) at a fast heating rate; the instrument is then switched to isothermal mode and the sample exposed to an oxygen atmosphere, by switching the purge gas. The OIT is expressed as the elapsed time from the test sample’s exposure to an oxidising gas, usually oxygen, to the onset of oxidation at the isothermal test temperature. The time interval is determined from the DSC curve as the time-distance between the admission of oxygen and the point of intersection of the ‘tangent’ to the oxidation exotherm and the ‘baseline’ (see Figure 1). (The isothermal test temperature is usually selected to produce OIT values in the range 15–100 min.) The OIT test is used to assess the relative stability of a series of related polymer samples. It does however suffer from several limitations, which can include poor reproducibility and precision [1,5–7]. Some of the issues relate to:
exo
The large difference often observed between the OIT for an unstabilised and a stabilised sample, this can make it difficult to compare stabiliser formulations by this method [1].
HEAT FLOW
to Temperature ramp begins
tmin
Begin O2 Isothermal period begins
endo
Sample melt OIT to TIME (min)
Figure 1 Example of an OIT experimental curve. Reproduced from Marcus and Blaine [4], by kind permission of TA Instruments.
Polymer Degradation and Oxidation: An Introduction
391
Finding an optimum test temperature [1,5–7]. If the temperature is too high then undesirable side reactions may occur. Also, concerns about the realistic nature of the test for predicting performance at ambient conditions could arise. Too low a temperature will compromise the detection sensitivity and signal-tonoise ratio of the measurement [5]. Test specimen thickness [1]. Polymer structure and formulation. As an example, Woo et al. [7] measured OIT values for series of commercial PVC resins and polyester thermoplastic elastomers (TPEs). The researchers used the ASTM D3895-80 procedure, but substituted air as the oxidising gas instead of pure oxygen. A dependency on thermal processing history of the TPE film samples appeared to influence the measured OIT; in the PVC study, chemically different chain ends affected polymer stability and hence OIT values. In a study on the thermal and UV ageing of two commercial poly(oxymethylene) (POM) samples, one of which was a copolymer (see related study discussed later under Section 4.3, thermogravimetric analysis (TGA)), used in car interior applications, involving both DSC and TGA, isothermal OIT measurements were made at several different temperatures [8]. One conclusion from this study was that ‘‘extrapolation of the OIT data from high temperatures (molten state) to ambient temperatures in the solid state does not reflect effective antioxidant performance at room temperature’’, and thus measurements close to the melting point are not appropriate for reliable lifetime estimations. An oxidation induction time can also be determined by CL experimental methods, see Chapter 11 in this book. Fearon et al. [9] modified a commercial DSC instrument such that simultaneous measurements could be made of heat flow and light emission. In a study of unstabilised polypropylene (PP) over a series of temperatures (1201C, 1301C and 1351C), which were below the melting temperature of the polymer, a linear relationship between (CL intensity)1/2 and DSC heat flow rate in mW was obtained, although the plots had different gradients at each temperature, decreasing slightly with increasing temperature (see Figure 2(a)). The results were rationalised as giving support for the CL emission arising from a Russell-type mechanism (see Chapter 11), and the fact that while DSC effectively measures chain propagation, CL is measuring chain termination, and the kinetic chain length varies with temperature. The study also incorporated measurements of OIT from stabilised PP samples. Excellent agreement was established between the two measurements (see Figure 2(b) and (c)). In the same publication [9], simultaneous DSC and CL data were reported from a bottle-grade poly(ethylene terephthalate) (PET) sample (see Figure 3). Figure 3 shows that in a measurement from an oxidising sample, while endothermic and exothermic processes affect DSC measurements, the CL signal is not directly affected by these (although secondary effects may be caused by such as changes in sample geometry due to melting). In this study, the oxidation of the PET polymer accelerates rapidly around the crystal melting point. In the DSC trace, it can be seen that this is difficult to distinguish from both the baseline
392
John M. Chalmers and Robert J. Meier
180
(CL intensity)1/2
140 120
CL@130°C
1.2 arb. units
160
135°C
0.8 0.4 130°C
0.0
100
0
40 80 120 Time/min
80
120°C
60 40 20 0 −0.6
−0.4 −0.3 −0.2 DSC/mW
−0.5
(a) 0.5
3.5e+6
1000
2.5e+6
0.0
2.0e+6 1.5e+6 1.0e+6
−0.5
CL /50 s OIT CL/min
DSC/mW
0.0
1200
3.0e+6
CL DSC
−0.1
800 600 400
5.0e+5 200
0.0 −1.0
0
40
0
80 120 160 200 240 280 320 360 460 Time/min
(b)
0
200
400
(c)
600
800
1000
1200
OIT DSC/min
Figure 2 (a) Unstabilised PP, plot of DSC heat flow rate vs (CL intensity)1/2; the plot shows all data up to the inflection point of the CL curve (below the peak maximum). The point when the analysis was terminated is illustrated in the inset. The lateral curve shift is a consequence of the DSC response (see Ref. [9] for full details). (b) DSC and CL traces obtained from stabilised PP at 1501C in O2. (c) Plot of OIT values obtained from DSC vs those determined from CL from stabilised PP at a range of temperatures. Reproduced from Fearon et al. [9], Figures 2–4. Copyright 2004, with kind permission of Springer Science and Business Media. 2
2.5e+5 DSC 2.0e+5
−2
CL
−4
1.5e+5
−6 1.0e+5
−8 −10
CL intensity/s-1
Heat flow/mW
0
5.0e+4
−12 −14
0.0 0
50
100
150 200 Temperature/°C
250
300
350
Figure 3 Simultaneously recorded DSC and CL of PET sample in an oxygen atmosphere. The heating rate was 101C min1. Reproduced from Fearon et al. [9], Figures 2–4. Copyright 2004, with kind permission of Springer Science and Business Media.
Polymer Degradation and Oxidation: An Introduction
393
curvature and the phase transition at melting; in contrast, the CL gives a sharp, unambiguous onset. In OIT determinations, the test samples are flushed continuously with oxygen during the course of the measurement [1]. This is in contrast to oxygen-uptake measurements that are mostly undertaken in a static oxygen atmosphere (see below). Effects such as dynamic removal of volatile antioxidants in the OIT method can lead to these two methods yielding very different assessments of a polymer formulation’s stability [1].
2.2 Oxygen uptake Perhaps conceptually one of the simplest tests for comparing the stability of related polymer samples is that of measuring oxygen uptake. In such a measurement the amount of oxygen reacting with a polymer sample, at a particular temperature and over a specific time, can be measured either manometrically or volumetrically, by a relatively simple device [1], such as that illustrated in Figure 4 [10]. Whereas such a measurement may be made on solid samples, such as sheet, powder or film, in order to minimise errors, the measurement is preferably made on thin film samples. The technique of oxygen uptake is an absolute quantitative technique; it affords a direct measure of oxygen consumption during polymer degradation [11]. Whereas techniques such as OIT and melt flow index (MFI, see later) measure the stability of a polymer melt, oxygen uptake can, in principle, be undertaken at any temperature; it also uses larger sample amounts than OIT, generally leading to improved reproducibility. (As far as the authors can ascertain, there are no recommended ASTM or ISO procedures for this method; an ASTM method (D4478-85, ‘Test Method for Oxygen Uptake’) existed, but seems to have been withdrawn in 1994 and not replaced.)
6 4
2 1
7
5
8
3
Figure 4 Schematic of an oxygen uptake device. 1, sample; 2, electrical oven; 3, Hg manometer; 4, intermediate vessel for pressure adjustment; 5, drying vessel; 6, control thermometer; 7, outlet to vacuum pump; and 8, inlet for gas feeding. Reproduced with permission from Zaharescu [10]. r Springer 2001.
394
John M. Chalmers and Robert J. Meier
An extensive review of oxygen uptake techniques for measuring polyolefin oxidation was published in 1995 [11]. This listed the methods described in the literature over the period 1908–1991. Two categories of technique apparatus are used for measuring oxygen uptake; these operate under either isochoric or isobaric conditions. In the former, constant-volume (CV) type, there is no replacement of the oxygen consumed; in the latter, constant-pressure (CP) type, the volume of oxygen required to maintain isobaric conditions during polymer oxidation is measured. In this latter compensating-pressure approach, two strategies are employed: (i) the volume of the sample cell is decreased by raising a mercury levelling bulb or by the motion of a piston or bellows, or (ii) the consumed oxygen can be replaced by electrolysis or from a reservoir. Gijsman and Hamskog [12] reported recently on a study of stabilised and unstabilised PP in apparatus that enabled the simultaneous measurement of oxygen update (OU) and imaging CL, which enabled them to obtain comparable information on an oxidising area. Some conclusions from the study were (see Ref. [12] for full details): The measurement of the induction time determined by CL and OU are, in general, comparable. However, at low temperatures, the OU induction time is shorter; this was postulated as being a decrease of sensitivity of CL at lower temperatures. The CL curve is related to the amount of degrading polymer. The OU and CL curves are not related to the kinetics of the degradation chemistry.
2.3 Carbonyl index The carbonyl index is not a standard technique, but is a widely used convenient measurement for comparing the relative extent and rate of oxidation in series of related polymer samples. The carbonyl index is determined using mid-infrared spectroscopy. The method is based on determining the absorbance ratio of a carbonyl (nCQO) band generated as a consequence of oxidation normalised normally to the intensity of an absorption band in the polymer spectrum that is invariant with respect to polymer oxidation. (In an analogous manner, a hydroxyl index may be determined from a determination of the absorbance intensity of a nOH band normalised against an absorbance band that is invariant to the extent of oxidation.) In the text following, two examples of multi-technique studies of polymer oxidation will be discussed briefly; each includes a measure of a carbonyl index. As part of a multi-technique investigation (see also discussion under midinfrared spectroscopy later), Corrales et al. [13] plotted the carbonyl index for films prepared from three grades of polyethylenes: a high-density PE (HDPE), a linear low-density PE (LLDPE) and a ‘metallocene’ PE (mPE) (see Figure 5). In this study, the data trend shown in Figure 5 correlated well with activation energies derived from the thermal analysis, which showed that the thermaloxidative stability followed the order LLDPEWmPEWHDPE, whereas the trend
395
16 14 HDPE LLDPE mPE
12 10 8 6 4 2 0 0
20
40
60 80 100 Ageing Time (h)
120
140
160
IR absorbance at 1720 cm-1/d (cm-1)
IR absorbance at 1720 cm-1/d (cm-1)
Polymer Degradation and Oxidation: An Introduction
6.0 5.5 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0
HDPE LLDPE mPE
0
20
40 60 Irradiation time (h)
80
100
Figure 5 Left: thermo-oxidative carbonyl index vs oven ageing times at 901C. Right: photooxidative carbonyl index vs irradiation time after exposure to UV radiation (300–800 nm wavelength). In each case, the carbonyl index is based on the intensity of the mid-infrared absorption at 1,720 cm1 normalised against sample film thickness, d, which was 290 mm. Reprinted from Corrales et al. [13]. Copyright 2002, with permission from Elsevier.
for photo-oxidative stability was mPEWHDPEWLLDPE. The thermal-oxidative results were also in accord with CL measurements, although the CL data for the photo-oxidative series demonstrated a higher light stability for the LLDPE compared to HDPE and mPE, both of which exhibited CL emission below their melting points. In another fairly recent multi-technique study to investigate the influence of chemical modification on polymer degradation, oxygen uptake, UV-visible spectroscopy and a mid-infrared spectroscopy carbonyl index were used in association with viscometry and DSC analyses for characterising the thermooxidative degradation of a series of polystyrene (PS) copolymers containing different amounts (5%, 10% and 15%) of –CH2(CQO)CH2CH2– units in their backbone [14]. The OU measurements were undertaken during the thermooxidative degradation at 1501C. For other analyses, samples were taken at various times from a degradation experiment at 1501C carried out in a closed vessel filled with pure oxygen. The OU measurements showed that the rate of oxidation of the copolymers was higher than for the homopolymer PS, yet while the 15% copolymer was highest, it was not proportionally higher in relation to comonomer content throughout the measurement (see Figure 6(a)). The increase of UV absorbance at 400 nm was used to follow increasing degradation (see Figure 6(b)); samples were examined as solutions in THF. The observations were in line with the observed enhanced yellowing of the copolymer samples. As can be seen from the figure, the UV absorbance became distinctly more pronounced for the highest (15%) copolymer content sample with increasing time. This observation was in accord with the measurement of carbonyl index obtained from mid-infrared spectra recorded as KBr discs (see Figure 6(c)). The carbonyl index was calculated as the ratio of the nCQO absorption band profile maximum occurring at 1,725 cm1 (assigned to newly formed CQO groups) in a degraded sample compared with the absorption value at this position before degradation. Also shown in Figure 6 is a plot of the intrinsic viscosity, IV (see Figure 6(d)). The decreases in IV are related to lower molecular weight species
Oxygen uptake (mmol/kg)
1600 1200 800 400 0 0
100
(a)
200 300 Degradation time (hour)
400
500
Absorbance at 400 nm
1.2 1 0.8 0.6 0.4 0.2 0 0
100
200
300
400
500
500
Degradation time (hour)
(b)
A1725(t)/A 1725(0)
3 2.5 2 1.5 1 0.5 0 0
100
200 300 Degradation time (hour)
400
0
100
200 300 Degradation time (hour)
400
(c)
Intrinsic viscosity (mL/g)
25
(d)
20 15 10 5 0 500
Figure 6 (a) Oxygen uptake vs degradation; (b) UV absorbance at 400 nm vs degradation time; (c) changes in carbonyl index vs degradation time; and (d) intrinsic viscosity vs degradation time. PS (~), 5% copolymer (’), 10% copolymer ( ), and 15% copolymer ( ). Reprinted from Botelho et al. [14]. Copyright 2004, with permission from Elsevier.
7
Polymer Degradation and Oxidation: An Introduction
397
formed following chain scission; once again a more pronounced effect was observed for the 15% comonomer sample. The Tg (glass transition temperature) values determined from DSC measurements for the PS and 15% comonomer samples were very similar being 1021C and 981C, respectively; however, while for PS only a slight decrease occurred with degradation, when the 15% sample was studied, a large decrease of Tg was observed, again supporting the formation of shorter chain material.
2.4 Wet chemistry/titration/staining The formation and role of hydroperoxide groups, particularly in the early stages of polymer oxidation is well discussed in the introduction to the next chapter and also features in many of the references cited in this chapter. Their detection and quantification is therefore important. Although this can be done directly or implicitly through many of the instrumentation techniques discussed in this chapter, there are several tests that have been developed, some of which are still widely used, that are based more on chemical methods, titration or staining. The majority have been applied to polyolefins, especially polyethylene. The most widely used is the iodometric colorimetric method [1,15]. The test is based on measurement of the triodide anion, I 3 , formed by reaction with a polymer. The concentration of I formed may be determined by either titrimetry 3 or UV absorption spectrophotometry (usually about 350 nm). If P signifies the polymer chain, the reaction may be represented as: POOH þ 3I þ 2Hþ ! I 3 þ H2 O þ POH The method does not usually detect dialkylperoxides, POOP [16]. In applying the method, a known weight of sample will be refluxed in a mixture of isopropanol and acetic acid in the presence of sodium iodide. The reaction time is usually about 30 min. A detection limit of ca. 30 ppm of hydroperoxide has been reported [1]. Iodometric titration formed part of a multi-method analysis of the oxidative degradation of LDPE [17]. Although reasonable reproducibility was obtained within a series of powdered samples, consistent results could only be obtained from pellets or thick films when the polymer was completely dissolved rather than just swollen. The hydroperoxide formation goes through a maximum as they decompose to form other oxidised species, such as hydroxyl groups, which eventually become predominant. Figure 7 shows a correlation obtained between the hydroperoxide content estimated by the iodometric test and the normalised intensity of the 3,552 cm1 mid-infrared band, which is characteristic of the –OOH group (see later); the linearity is maintained as long as the band at 3,552 cm1 increases steadily, i.e., while the hydroperoxide groups remain essentially isolated, but is lost once associated groups become predominant. Another method is that based on the ferrous/ferric thiocyanate determination of hydroperoxides [1]. This exploits the ion-catalysed decomposition as shown by
398
John M. Chalmers and Robert J. Meier
0.8 0.7
Hl (A3552 /lA2010)
0.6 0.5 0.4 0.3 0.2 0.1 0 0
10
20
30 40 R-OOH, μ mol/g
50
60
70
Figure 7 Hydroperoxide index (HI) determined from mid-infrared spectroscopy (ratio of the integrated intensity of the 3,552 cm1 band to the integrated intensity of the band at 2,010 cm1) as a function of total hydroperoxide content measured by iodiometric titration. films (0.8 mm thick) thermally oxidised in air at 1601C for 0, 4, 5 and 10 min; K beads exposed to summer daylight for 2 months; ’ beads exposed to summer daylight and then thermally treated at 1201C for 0, 30, 60 and 90 min. Reprinted from Salvalaggio [17]. Copyright 2006, with permission from Elsevier.
7
the reaction: POOH þ 2Fe2þ þ 2Hþ ! 2Fe3þ þ H2 O þ POH The concentration of Fe3+ ions can be determined by titration with ferrous ammonium thiocyanate or spectrophotometrically by measuring the absorbance at 512 nm of the [Fe(SCN)6]3 complex [1]. In a recent study of the degradation of pre-aged (oven ageing and photooxidation) hydrocarbon homopolymers exposed to stimulated recycling, the ferric spectro-colorimetric method based on the stoichiometric of oxidation of Fe2+ ions to Fe3+ was used to determine hydroperoxide content [18]. The Fe3+ ions react with the thiocyanate to give an intense colour that is proportional to the hydroperoxide content; the study also involved use of DSC, MFI and tensile strength measurements. Figure 8 shows a plot of hydroperoxide formation in LDPE, which was unprotected by stabilisers, during oven ageing at 1001C. A similar behaviour was observed for high-impact polystyrene (HIPS) used in this study, whereas HDPE and PP remained very stable, even after 10 months oven ageing and no hydroperoxide formation could be detected. Another method of investigating the degradation levels of polymers involves staining in order to provide a greater sensitivity for spectroscopic/colorimetric techniques [1]. Staining can provide a very fast, low cost, simple to operate method of detecting/monitoring degradation in some polymers. Staining materials that have been used include: SO2, 2,4-dinitrophenylhydrazine (DNPH), dansyl hydrazine (DNSH: dimethylaminonaphthyl-5-sulfonylhydrazine),
ROOH [mmol/l]
Polymer Degradation and Oxidation: An Introduction
399
5 4.5 4 3.5 3 2.5 2 1.5 1 0.5 0 0
5
10
20 25 15 Exposure time (days)
30
35
Figure 8 Hydroperoxide formation in LDPE granules during oven ageing at 1001C. Reprinted from Luzuriaga et al. [18]. Copyright 2006, with permission from Elsevier.
diphenyl-p-phenyldiamine, dansyl butyramide, iodine vapour, alkaline Procion black, Benedict’s solution and Tollen’s reagent, and Sudan III/methylene blue staining [1]. Aslanzadeh and Kish [19] recently used staining as part of a multi-technique (staining/colorimetric, scanning electron microscopy (SEM), mid-infrared and density) method of studying the photodegradation of thermalbonded PP non-woven fabric samples. The samples, commercial thermal-bonded non-woven fabrics manufactured from isotactic PP, were UV photo-degraded and then immersed in the stirred boiling staining solution for 15 min, then rinsed in isopropanol and distilled water, before drying. The staining solution was pure isopropanol saturated with Sudan III and methylene blue at room temperature, to which after a period of stirring extra pure NaOH was added, followed by more stirring. Figure 9 shows the changes in (a) redness and (b) blueness obtained from the colorimetric analyses. As can be seen, blueness increases linearly with POOH index (P ¼ polymer chain), while redness decreases with POOH index; the POOH index was determined from mid-infrared spectroscopic measurements (see Ref. [19] for full details).
2.5 Melt flow index Although essentially a bulk (rheological) property, the melt flow index (MFI) measurement is included here, since it complements the other techniques covered in this chapter and also is sometimes performed in parallel with these in investigations into polymer degradation, since oxidation/degradation can induce changes in the molecular weight distribution of a polymer. The measurement of MFI is a standard property method the procedure of which is described in ASTM D1238 [20] and ISO 1133 [21]; the two standard methods are essentially very similar in procedure. An alternative term for melt flow index is melt flow rate (MFR). The MFI test is a simple, low cost, rapid and convenient method for characterising the extent of degradation [1]; a decrease in MFI is indicative of a cross-linking mechanistic pathway; an increase in MFI indicates that chain
400
John M. Chalmers and Robert J. Meier
25.00
delta a*
20.00 15.00 10.00 y = -4.3472x+24.503 R2 = 0.9558
5.00 0.00 0
1
2
3
4
5
4
5
POOH Index (a) 5.00 0.00 1
2
3
delta b*
-5.00 -10.00 -15.00 -20.00
y = -5.4587x + 4.4603 R2 = 0.9725
-25.00 POOH Index (b)
Figure 9 Stained photo-degraded non-woven PP fabric samples (a) change in redness with POOH index, (b) change in blueness with POOH index. Reprinted from Aslanzadeh and Kish [19]. Copyright 2005, with permission from Elsevier.
scission has taken place. The first mechanism leads to a reduction in molecular weight (MW); chain scission leads to an increase in MFI. The MFI is most commonly applied to polyolefins. It is measured using a capillary melt viscometer. A schematic of a MFI apparatus is shown in Figure 10 [22]. The test consists of weight-loaded piston under the action of gravity forcing a heat-softened polymer through a rod die of specified dimensions [22]. A small amount of a sample, typically about 4–5 gm, is packed into the barrel, avoiding air pockets, which is then pre-heated for a specified time; for polyethylene this is 5 min at 1901C; for PP this is 6 min at 2301C. After this, a weight, usually 2.16 kg, is loaded onto the top of the piston. Three samples are then cut from the extruded melt at constant time intervals, which are each then weighed accurately, and the
Polymer Degradation and Oxidation: An Introduction
401
Weight (popular condition 2160 gms incl.piston) Mercury in Glass Thermometer
Oil Filled Thermometer Well
Nitride Hardened Steel Barrel
Heater around Barrel (well insulated)
Weight Loaded Piston
Extrusion Die - held in place by retainer plate
Figure 10 Schematic of MFI apparatus. Reproduced from Hunt and James [22]. r with kind permission of Springer Science and Business Media.
MFI is reported as the number of grams of polymer/10 min of flow time. The flow rate will depend on the polymer and the conditions used; lower MW polymers will tend to flow through the die faster than higher MW polymers. A recent example of the use of determination of MFR in a polymer degradation study is that undertaken on the thermo-oxidative degradation of metallocene polyethylenes (mPEs) [15], which differed in their initial melt index, molar mass distribution, density and ash content. The degradation series of samples was prepared by processing (masticating) each sample in a torque rheometer open to air and operating at 10 rpm and a temperature of 225751C for differing lengths of time (15, 30, 45, 90 and 120 min). The MFI of these samples was determined by applying a standard weight of 10 kg at a melt temperature of 1901C, in accordance with ASTM D1238. Additional to the MFI measurements, transmission mid-infrared spectroscopy (see Section 3) was used to measure the level of vinyl and trans-vinylene unsaturated groups in each sample by examining a 200 mm thick compression moulded film prepared from each sample; mid-infrared spectroscopy was also used to measure the relative levels of carbonyl groups formed by measuring the normalised intensity of a band between 1,715 and 1,720 cm1. Also, an iodometric colorimetric test was
402
John M. Chalmers and Robert J. Meier
undertaken to ascertain the levels of hydroperoxides formed. All the samples examined initially showed a large decrease in MFI with increasing processing consistent with a predominance of cross-linking reactions. One sample, from between 15 and 30 min mastication, showed a slight increase in MFI, indicating an increased proportion of chain scission taking place during this period. Differences in the rates of formation and relative changes in the levels of unsaturated, carbonyl and hydroperoxide groups were correlated with and used to rationalise the different behaviours observed in the mPEs as determined by the MFI measurements.
3. SPECTROSCOPIC TECHNIQUES 3.1 Mid-Infrared spectroscopy1 The mechanisms of oxidation in the degradation of polymers is well described in Chapter 11 co-authored by Richly´ and Matisova´-Rychla´, and will not be repeated here; suffice it to say here that one of the most informative and sensitive techniques to observe functional groups associated with oxygen is infrared (IR) spectroscopy, and many researchers have used mid-infrared spectroscopy to study and investigate degradation reactions and processes in polymers. As expected, many of the early reported fundamental studies focused on polyolefins, in particular polyethylene [23,24] in which many of the effects of oxidation and degradation may be readily observed. As explained in Chapter 11 by Rychly´ and Matisova´-Rychla´, one of the key early steps in the oxidation processes is the formation of hydroperoxide groups; these give rise to a distinctive absorption band in the mid-infrared spectrum of polyethylene that may be observed at 3,555 cm1 [23] (see, e.g., Figure 11(a)). Further oxidation leads to a variety of carbonyl groups with characteristic absorption bands in the region 1,800–1,675 cm1; these may be variously assigned to species such as esters (1,740 cm1), aldehydes (1,730 cm1), ketones (1,720 cm1), acids (1,705 cm1), peracids (1,785 cm1) and peresters (1,763 cm1) (see Figure 11(b)). Also generated are absorption bands due to hydroxyl species; these occur in the region 3,600–3,200 cm1 (see Refs. [25] and [26] and references therein). As such, the sensitivity of mid-infrared spectroscopy is especially useful for characterising the consequences of thermal, thermal-oxidative, photo, photo-oxidative and radiation-induced degradation, not only in the regions associated with oxygenated functional groups, but also those associated with unsaturated olefinic groups. For example, in low-density branched polyethylene photooxidation tends to lead to an increase in the level of the bands characteristic of the vinyl (–CHQCH2) end group, which is characterised by a pair of bands occurring at 990 and 910 cm1, whereas thermal-oxidation tends to lead to a reduction in relative intensity of the band attributed to vinylidene (WCQCH2) 1
While most of the references tend nowadays to use FT-IR/FTIR (Fourier transform infrared) to denote the use of mid-infrared spectroscopy, we mostly use the more precise phrasing of mid-infrared (mid-IR) spectroscopy.
403
Polymer Degradation and Oxidation: An Introduction
Before heating
2h at 145 °C
Before heating
( OOH)
C C O
ROOOR O
3380 cm ( CH)
CH−CH−C− 1705
RCOR
1718
1780
3620 cm-1 3555
Cooled 24 h
1788
O ROOOH O
-1
6h at 145 °C
1785
4h at 145 °C
1640
Carbonyl band when reheated to 145°C for 1.5 h in air, N2 or O2 (Actual spectrum of reheating in O2)
Absorption
5 h at 145°C 6 h at 145°C Cooled in air for 24 h to room temperature
1665
3h at 145 °C
1740
Absorption
3 h at 145°C
RCHO
O RCOH O R−C−R
3750
3500
Wavenumber (a)
3200 (cm-1)
1850 1800 1700 1600 Wavenumber (cm-1) (b)
Figure 11 Mid-infrared transmission spectra recorded from a linear (high-density) polyethylene before, during and after oxidation at 1451C: (a) OH stretching region, (b) carbonyl stretching region. Reproduced from Luongo [23]. Copyright 1960 John Wiley & Sons, Inc.
unsaturation that occurs at 888 cm1 [26]. Observation of variation in intensity of all these absorption bands may form part of a basic study into a polymer or polymer formulation stability study, or they may form part of an investigation into a product failure or deterioration; the latter often being undertaken using FTIR microscopy. As discussed earlier under Section 2.3, Carbonyl index, in one relatively recent comparison of the photo-oxidative and thermal (oven-aged) degradation behaviour of different polyethylenes, additive free grades of a metallocene (mPE), an HDPE and a linear low-density PE (LLDPE) were analysed by a combination of mid-IR spectroscopy, TGA and CL [13]. The mid-IR
404
John M. Chalmers and Robert J. Meier
measurements were used to provide a carbonyl index (see earlier); also determined were relative changes in free (3,555 cm1) and associated (3,410 cm1) hydroperoxides, hydroxyl (3,371 cm1) esters (1,743 cm1), aldehydes (1,733 cm1), ketones (1,720 cm1) and acid (1,712 cm1) groups, and chain branching level through measurement of the dCH3 absorbance band at 1,378 cm1. (Second derivative UV spectra were used to estimate the initial concentration and evolution of vinyl groups.) Activation energies determined from TGA experiments were shown to decrease during thermal degradation in the order HDPEWmPEWLLDPE, whereas under conditions of photo-oxidation they followed the order mPEWHDPEWLLDPE. The rates of oxidation as indicated by the mid-IR determined carbonyl index correlated with the respective changes in activation energies (see also figures and discussion under Section 2.3, Carbonyl index). A microscope hot-stage, fitted with barium fluoride windows, inserted into the beam of a FTIR spectrometer was the apparatus of choice for a study of the kinetics and mechanisms of the thermal degradation of poly(methyl methacrylate) (PMMA) leading to char formation [27]. Thin films (ca 1 mm thick) were degraded in an atmosphere of argon (to avoid oxidation) isothermally at temperatures between 3401C and 4201C. To complement these mid-IR studies, TGA was also carried out under similar conditions on selected samples. An advantage of using mid-IR for the study was that it could be used to provide information about the chemical changes that occurred in the polymer residue. In the temperature range 340–3851C, mid-IR spectra were recorded at 10 min intervals; at 4001C they were recorded at 2 min intervals; at 4201C they were recorded at 1 min intervals. One series of samples analysed was of a monodisperse PMMA with peak molecular weights, Mp, between 12,700 and 1,520,000; each chain was terminated at one end by a hydrogen atom and at the other by a 2,2-diphenyl hexyl group. Selected figures reported from this study [27] are shown in Figure 12. Figure 12(a) shows a stack plot of some typical changes observed in the mid-IR spectra at 3701C. The band at 1,550 cm1 that develops with increasing degradation was assigned to a conjugated unsaturation band, and developed in part through the mechanism proposed in Figure 12(e). The build up of this band with time at 3701C for the different Mp polymers can be seen in Figure 12(f), in which the ratio c/m represents the absorbance of the band at 1,550 cm1 divided by the initial height of the nCQO carbonyl band (1,730 cm1). Figure 12(b) show the mid-IR spectrum of the final residue (PMMA char) remaining after isothermal degradation at 4201C. The spectrum is dominated by the intense band at 1,550 cm1, formed mainly by side-group elimination by scission of the C–C bond of the methoxy-carbonyl side group [27]. Figure 12(c) shows the change (% conversion) of selected mid-IR absorbance bands of the lowest Mp polymer at 3701C. Up to 20% conversion, first-order rate plots from the bands at 1,730, 1,234 and 1,139 cm1 showed good linearity (see Figure 12(d)). Above 20% conversion, those samples with a lower initial degree of polymerisation, D, produced relatively more conjugation. This was attributed to either ‘‘a greater number of unsaturated end-groups, as CQC from previous scission or from activation by the 2,2-diphenyl hexyl group, joining with unsaturated groups from the side-chain elimination, following depropagation’’
Polymer Degradation and Oxidation: An Introduction
405
(see Figure 12(g)). From the combined mid-IR and TGA study, some of the overall conclusions reached were that: thermal degradation was initiated by a mixture of chain end and chain scission processes, at lower degradation temperatures, this was followed by depropagation, and first-order termination,
0.2
0.25 absorbance
0.4
absorbance
0.6
0.0
0.20
t90 0.15 t70 t50 0.10 t30 time t10 / seconds 0.05 2800 2400 2000 1600 1200 800 wavenumber / cm-1 4000 3500 3000 2500 2000 1500 1000 wavenumber / cm-1
(a)
(b) 1.2 0.30
0.8
0.25
0.6
0.20
In (1 - x)
% conversion
1.0
0.4 0.2 0.0
0.15 0.10 0.05
0
2000 4000 6000 time / seconds
8000
2950 cm-1
1730 cm-1
cm-1
cm-1
1234
1550 cm-1 (c)
1139
0.00
0
500 1000 1500 2000 2500 3000 time / seconds 1730 cm-1
1234 cm-1
1139 cm-1 (d)
Figure 12 (a) Mid-IR absorbance spectra recorded from the thermal degradation of PMMA (Mp ¼ 12,700) (under argon) at 3701C. (b) Mid-IR absorbance spectrum of the final residue (char) produced on thermal degradation of PMMA (Mp ¼ 12,700) (under argon) at 4201C. (c) Change in absorbance of some mid-IR bands of thermally degraded PMMA (Mp ¼ 12,700) (under argon) at 3701C. (d) First-order rate plot for loss of absorbance of bands at 1,730; 1,234 and 1,139 cm1 for PMMA (Mp ¼ 12,700) (under argon) at 3701C. (e) Proposed mechanism of side-group elimination in thermally degraded PMMA. (f) Buildup of conjugation band at 1,550 cm1 with time for PMMA samples thermally degraded at 3701C. (g) Proposed mechanism for end-group contribution to the intensity of the mid-IR band at 1,550 cm1. Reprinted from Holland and Hay [27]. Copyright 2001, with permission from Elsevier.
406
John M. Chalmers and Robert J. Meier
0.35
elimination
O OO O O O
O O
c/m
H H
O O +
O O
0.30 0.25 0.20 0.15 0.10 0.05
OR CO2+ CH4
0.00 0
2000
4000
6000
8000
time / seconds
proposed structure of char (e)
12,700
28,700
69,000
174,000
1,520,000 (f) double bond from scission of end-group or chain
side-chains eliminated
O OO O O OO OO O
depropagation
O O conjugated product gains one C= (g)
Figure 12 (Continued)
at higher temperatures, initiation was followed by depropagation mostly to the end of the polymer chain, under the conditions used, thermal degradation of PMMA eventually produces a char; the amount of char being dependent on molecular weight and temperature. Hot-stage FT-IR spectroscopy has also been employed monitoring chemical changes in nylon 6 and nylon 6,6 undergoing isothermal degradation (under an argon atmosphere) at temperatures in the range 350–3701C [28]. Complementary data was supplied from measurements by TGA, DSC and solution viscosity. The mid-IR results showed that the thermal degradation led to formation of an aromatic-conjugated structure indicated by development of a new band at 1,590 cm1; also noted was the appearance of a band at 2,190 cm1 indicative of a keteneimine formed from the dehydration of an amide linkage. Chemical changes leading to formation of volatile products, cross-linking, formation of an
Polymer Degradation and Oxidation: An Introduction
407
aromatic-conjugated material and eventual formation of a black char residue, are a consequence of the thermal degradation at these temperatures. The thermal(under nitrogen) and thermo-oxidative (under oxygen) degradation in an environmental chamber of nylon 6 and nylon 6,6 at 2001C were also the subject of an earlier in situ FT-IR investigation [29]. At these temperatures, under a nitrogen atmosphere, the majority of observed spectral changes could be associated with crystallinity or crystalline-phase changes; under an oxygen atmosphere the trends observed were a decrease in intensity of all absorbance bands related to amide groups accompanied by growth of other carbonyl and hydroxyl species. Coleman and Sivy also used an infrared transmission cell to undertake degradation studies under reduced pressure on a series of poly(acrylonitrile) (ACN) copolymers [30–33]. Thin films prepared from a polymer were mounted in the specially designed temperature-controlled cell mounted within the infrared spectrometer. The comparative studies were made on ACN copolymers containing vinyl acetate [30,32], methacrylic acid [30,31] and acrylamide [30,33]. The species monitored was the production of the cyclised pyridone structure. This was characterised in part by loss of CRN stretch (nCRN) intensity at 2,240 cm1 accompanied by the appearance and increase in intensity of a doublet at 1,610/1,580 cm1. Many of the carbonyl and hydroxyl species that are formed as a consequence of oxidation have fundamental absorption bands that severely overlap; this sometimes makes discriminating between particular species difficult. This limitation can sometimes be overcome, or at least partially, through the use of chemical derivatisation [34]. For example, alkali treatment of oxidised polyethylene can be used to convert acid carbonyls to carboxylate salts; this results in a shift in the band position, since the carbonyl band of a saturated carboxylic acid occurs at ca. 1,710 cm1, whereas the antisymmetric stretch of the carbonyl band of the carboxylate salt occurs at ca. 1,610 cm1. Another possibility is treatment with SF4; this converts the carboxylic acid to and acid fluoride, thereby shifting the band from ca. 1,710 to ca. 1,840 cm1 [1]. In a study of the thermo-oxidative degradation of heterophasic ethylene/propylene copolymers and their fractions, both NH3 and SF4 were used to convert carboxylic acids to the ammonium salt or acyl fluoride, respectively [35]; the latter treatment was preferred since while the ammonium salt formation was quantitative, the bands formed are very broad. More distinct information was available through formation of the acyl fluoride, which created the disappearance of two bands in oxidised isotactic PP, one at 1,710 cm1, the other at 1,760 cm1, which were assigned as originating from carboxylic acids in different environments, one from dimers and one from an associated form between a carboxylic acid and a non-carboxylic acid hydroxyl group, respectively. In LLDPE, however, only the conversion of the typical dimeric acid group was observed. Additionally in this study, derivatisation using NO was particularly helpful for elucidating mechanisms in the thermo-oxidation of the ethylene/propylene copolymers, since it reacts with hydroperoxides and alcohols to give nitrates and nitrites with characteristic absorption bands, respectively. SF4, NH3 and NaCl treatments were all used in an investigation of the photo-oxidation of anhydride-cured epoxies [36]. SF4-derivatisation reaction
408
John M. Chalmers and Robert J. Meier
has also been employed to aid mid-IR identification of photo-products on photooxidised films of bisphenol-A-polycarbonate in a combined analysis involving mid-IR, mass spectrometry (MS) and UV spectroscopy [37]. Whereas SO2 has been used more simply as a staining technique (see earlier) to monitor hydroperoxide formation, it has also been used to characterise oxidised polyolefins [38] in order to gain insight into the sites of oxidative attack. Reaction of SO2 with PE that was expected to have been oxidised to a low level confirmed that hydroperoxide formation probably takes place in the b-position to a pendant methylene (vinylidene) group (a defect structure in PE) (Figure 13). Figure 13 shows that negligible differences were observed in the mid-IR spectra of a control LDPE and a PE oxidised to a low level until they were treated with SO2. These samples were part of a study into storage in a silo of PE granules arising from a bulk property deterioration complaint. Melt flow measurements had indicated that the stored material was subject to setting up. However, preliminary IR examination of the ‘oxidised’ complaint sample revealed no sign of absorptions due to hydroperoxide or carbonyl groups. Assuming that the complaint sample was more oxidisable, the samples were heated in an air oven to
Figure 13 Left: FTIR absorbance spectra of a control LDPE sample and difference spectra, (A, as received; B, after SO2 treatment; C, heated at 1001C for 18 h; D, heated at 1001C for 18 h then SO2 treated.) Right: FTIR absorbance and difference spectra of ‘oxidised’ sample, (A, as received; B, after SO2 treatment; C, heated at 1001C for 18 h; D, heated at 1001C for 18 h then SO2 treated.) Reproduced from Henman [38]. r, with permission from Elsevier.
Polymer Degradation and Oxidation: An Introduction
409
enhance the differences between the complaint and the control sample, as indeed was the case (see Figure 13). As can be seen in the figure, reaction with SO2 resulted in a loss absorbance at 888 cm1 of vinylidene unsaturation in the complaint sample, which was enhanced after the heat treatment, whereas no such loss could be detected in the control sample. In addition to transmission spectroscopy finding extensive use as a sampling technique for studying the bulk degradation effects on such as polymer films, the surface layer specific sampling technique of attenuated total reflection (ATR), also referred to as internal reflection spectroscopy, finds extensive use for interrogating the surface layer of oxidised/degraded/irradiated polymer films and products. Depending on the experimental conditions employed, the ATR approach will probe a surface layer of between ca. 0.3 and 5 mm over the range 4000–400 cm1 [26]. A limitation of the technique is that the depth probed is wavenumber dependent, being greater towards lower wavenumber, so that in any ATR measurement the surface layer probed varies over the spectral range examined. Unlike X-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometry (SIMS), see later, ATR mid-IR is not a surface-specific technique, but may be regarded rather as a surface layer-specific technique. One method of promoting the adhesive properties of some polymer films is exposure of their surfaces to corona discharge in air. This introduces oxidised polar groups on the film surface, which may be investigated by mid-IR ATR spectroscopy (and, of course, XPS and SIMS techniques, see later). The surface oxidised species on isotactic PP films generated as a consequence of corona discharge were identified by mid-IR ATR spectroscopy and a carbonyl index plotted as a function of corona discharge treatment time (Figure 14 [39]). The 1.4 1.2
Carbonyl index
1.0 0.8 0.6 0.4 0.2 0.0 0
20
40
60 80 Treatment time (s)
100
120
Figure 14 Carbonyl index as a function of corona discharge treatment of PP film. Reproduced with permission from Sellin and Campos [39].
410
John M. Chalmers and Robert J. Meier
mid-IR results were complemented by topographic images obtained by atomic force microscopy (AFM) and wettability (contact angle). With increasing generation of lower molecular weight surface oxidised groups, and decrease in contact angle with water, the film adhesion property improves. ATR-FTIR spectroscopy alongside electron spin resonance imaging (ESRI, see Chapter 12 in this book) was employed in a spatial resolution study of the effects of photo- and thermo-oxidation processes in stabilised polystyrene (PS) and PP plaques exposed to accelerated photo- or heat-ageing [40]. The samples examined were cylindrical samples (3 mm diameter, 6 mm length) that had been bored out from the plaques after exposure for different time periods. (The cylindrical samples were more appropriate for the ESRI examinations.) ESRI, the primary technique in this investigation, was used to determine concentration profiles of nitroxides along the cylinder axes coinciding with the direction of irradiation in the weatherometer. The main supporting role of the ATR FT-IR measurements was to compare the relative amounts of WCQO and –OH existing on unexposed and exposed surfaces from both aged and unaged samples and the surface formed by cutting the exposed samples in the middle of their thickness. It was found that the relative intensity of WCQO bands formed on irradiation was much higher for PS than PP, it being greatest on the irradiated PS surface; the extent of formation of WCQO groups was approximately equal on both the irradiated and unexposed surfaces of the irradiated PP sample. In a novel application, ATR mid-IR was used for studying the thermal degradation of chlorosulfonated polyethylene (Hypalons) glove samples [41]. The glove samples were aged in circulating air in temperature-controlled ovens. A main use of Hypalons gloves is as gloves for glove-box use, because of the material’s resistance to alcohols, strong acids and bases. The ATR spectra recorded from aged series of samples were subjected to multivariate data analysis using a multivariate curve resolution technique (MCR), using an alternative least squares (ALS) algorithm. The loadings from such an analysis are related to component spectra, the scores of which are related to concentration. From this data analysis, the dominant degradation pathways were deduced to be formation of –CQC– via dehydrochlorination, loss of –SO2 functionality, oxidation to form ketones, and cross-linking. The scores from the extracted MCR factors as functions of time showed the onset and duration of a particular mechanism. The correlation of the deterioration of polymer properties with degradation, such as mechanical performance and lifetime, is key to many areas, and has ever increasing importance in areas such as biodegradability, waste disposal and recycling. Jansson et al. simulated a recycling processing step on a series of unstabilised PP samples, which had been previously aged at 701C for differing lengths of time [42]. Following a second compression moulding it was found that the hydroperoxide content, determined by an iodometric test, decreased by rapidly transforming to additional carbonyl groups (Figure 15). The implication of this observation is that in order to maintain mechanical property performance, the polymers must be re-stabilised before recycling. The variation in carbonyl and hydroxyl species type and concentration were monitored using mid-IR spectroscopy on series of g-sterilised polyolefin film samples that had been
411
Polymer Degradation and Oxidation: An Introduction
0.8 1750 cm-1
1712 cm-1
0.7 1775 cm-1
Aged 8 days
0.6 Aged 8 days and reprocessed
Aged 7 days
Absorbance
0.5 0.4
Aged 6 days Aged 7 days and reprocessed
0.3 Aged 5 days
Aged 6 days and reprocessed 0.2
Aged 5 days and reprocessed
Unaged
0.1 0.0 2000
1900
1800
1700
1600
1500
Wavenumber [cm-1]
Figure 15 IR absorbance spectra of PP films after ageing in air at 701C (dashed curve) and after ageing at 701C and re-processing (solid curve). Reprinted from Jansson et al. [42]. Copyright 2004, with permission from Elsevier.
subjected to composting and fungal (microbial) culture environments [43]. Changes in viscosity and surface morphology (by SEM) were also monitored. The series comprised samples of isotactic PP, HDPE and ethylene/propylene (E/P) copolymers. It was concluded that pre-treatment by g-irradiation (sterilisation) accelerated significantly the biodegradation of the polymers. PP was found to be more susceptible to microbial attack than HDPE; comonomer composition and distribution were found to affect the behaviour of the E/P copolymers. Mid-IR spectroscopy, alongside gravimetric and molecular weight determinations, has also been used to analyse the biodegradation by a thermophilic bacterium (isolated from soil) of an LDPE film [44]. The mid-IR studies were undertaken using the ATR sampling technique on control samples, samples that had been UV irradiated, and samples that had been UV irradiated then incubated with bacteria. The study showed that the particular bacterial strain was capable of utilising standard and photo-oxidised polyethylene as the sole carbon source. FTIR microscopy, in which a FTIR spectrometer is coupled to an optical microscope, enables mid-IR spectra with a lateral spatial resolution of ca. 10 mm to be recorded from samples. (Higher lateral spatial resolution spectra suffer significantly from diffraction effects.) The attributes of FTIR microscopy can be successfully employed to probe the depth of degradation into a polymer product. The procedure involves analysing a cross-section slice microtomed in a plane perpendicular to the axis of irradation/degradation [34] (see, e.g., Figure 16(a)). A profile of the degradation products through such as a polymer film may then
412
John M. Chalmers and Robert J. Meier
Figure 16 (a) Schematic for obtaining a thin microtomed cross-section for FTIR microscopy analysis. (b) Oxidation profile for a polyamide film based on the absorbance at 1,715 cm1. The thickness of the microtomed layer was 30 mm. The sample had been artificially aged for 75 h at 601C. Reproduced with permission from Gardette [34]. r John Wiley & Sons Ltd., 2002.
be obtained by recording spectra from successive localised areas along the film thickness axis (see e.g., Figure 16(b)). As Figure 16(b) shows, only the outermost portion of the sample has been photo-oxidised in to a depth of ca. 40–60 mm; the core (bulk) of the polyamide film sample remains unaffected, as detected by FTIR microscopy. In addition to characterising the effects of degradation by recording spectra related to solid-state changes, FTIR spectroscopy (like MS, see later) can also be used to detect the evolved volatile products from such as a pyrolysis or TGA experiment (see Section 4.3 on TGA later). In one such study, the CO2 generated from a series of TiO2-pigmented LDPE films was monitored by FTIR spectroscopy; the apparatus (cell) used allowed for in situ UV exposure under controlled temperature, reaction atmosphere and humidity conditions, and mid-IR detection of the off gases [45]. Ranking of the samples according to either the rate of carbonyl development in the film samples or rate of CO2 evolution were identical. On-line analysis of the volatile products from the pyrolysis (under nitrogen) over the range 1,073–1,273 K of nylon 6,6 has been reported [46]. Such information can be useful in predicting the formation of nitrogen oxides during incineration of plastic wastes. Among the evolved gases detected were HCN, CO, NH3, CO2 and light hydrocarbons. Two competing mechanisms were deduced, one at low temperature that yields carboxylic acid and amines that release NH3, and one at high temperature that leads to formation of nitriles (see Figure 17). The primary volatile products evolving from the pyrolysis in the range 220–6001C of poly(3-hydroxy butyrate) (PHB) were passed through a gas chromatogram for separation prior to their identification by on-line FTIR spectroscopy [47]. The pyrolysis/gas chromatography (GC)/FTIR analysis was accompanied by weight loss determinations from TGA measurements (see later). Figure 18(a) shows the Gram–Schmidt chromatogram (reconstructed from the total mid-IR absorbance variation with time) obtained at four pyrolysis
413
Polymer Degradation and Oxidation: An Introduction
40
Fuel N coversion yield (%)
35 30 25 20 15
HCN NH3
10 5 0 0
0.5
1.5
1
2
residence time (s) 40
Fuel N coversion yield (%)
35 30 25 20 15 10
HCN NH3
5 0 0.2
0.3
0.4
0.5 residence time (s)
0.6
0.7
0.8
Figure 17 Conversion of fuel nitrogen to HCN and NH3. Furnace temperature: top, 1,073 K; bottom, 1,273 K. Reprinted from Leichtnam et al. [46]. Copyright 2000, with permission from Elsevier.
temperatures. Figure 18(b) shows the infrared spectrum recorded from the peak 2 that eluted at ca. 20 min. As can be seen in the insert it features two carbonyl bands. These occur at 1,770 cm1 and 1,759 cm1, and are associated with S-trans and S-cis conformations of 2-butenoic acid, respectively. Peak 1 had contributions from both evolved CO2 and propene; peaks 3 and 4 were identified as essentially dimer- and trimer-type structures of 2-butenoic acid, each containing an a,bunsaturated ester group and an acid functionality, with peak 3 containing additionally a saturated ester group. The two-step degradation of commercial ethylene-vinyl acetate (EVA) copolymers has been investigated using TGA coupled with FTIR detection of the pyrolytic products evolved [48]. Acetic acid was evolved from the first
414
John M. Chalmers and Robert J. Meier
1 600°C
Intensity
400°C
300°C
2
3
220°C
0
4 10
5
20 15 25 Times (minutes) (a)
30
35
40
Absorbance
Peak 2
1800
1750
1650 1700 Wavenumber (cm-1) (b)
1600
Figure 18 (a) GC-FTIR Gram–Schmidt chromatograms from evolved gases from PHB at pyrolysis temperatures of 2201C, 3001C, 4001C and 6001C. (b) FTIR spectrum recorded from peak 2 in chromatogram, identified as 2-butenoic acid. Reprinted from Gonzalez et al. [47]. Copyright 2005, with permission of Elsevier.
decomposition (360–4501C); gases identified from the second decomposition (450–5501C) were: 1-butene, ethylene, methane and CO2. The merits of TGA-FTIR for studying polymer degradation were reviewed in 1999 by Wilkie [49].
3.2 Raman spectroscopy The sensitivity of Raman spectroscopy to CQC species is clearly demonstrated in its application to the study of PVC degradation. As PVC unzips and
Polymer Degradation and Oxidation: An Introduction
415
100 090 080 ABSORBANCE
070 060 050 040 010 020 040 0 340
360
380
400 450 500 Wavelength (nm)
600
700
800
Figure 19 Example of a UV-visible absorption spectrum recoded from a typical thermally degraded PVC sample. Reprinted with permission from Gerrard and Maddams [50]. Copyright 1975 American Chemical Society.
dehydrochlorinates (loses HCl) conjugated polyenes are formed in the polymer backbone, which give rise to chromophores that absorb in the UV-visible region (see, e.g., Figure 19 [50]). Once the number of double bonds in the conjugation sequence reaches 6, this electronic absorption occurs in the visible region, giving rise to discolouration of the polymer. Using a Raman spectroscopy excitation laser that is in coincidence (or near coincidence) with the maximum absorption wavelength of one of these chromophores will give rise to a resonance Raman spectrum, in which the Raman scattering bands due to the conjugated species causing the chromophore will be enhanced by several orders of magnitude, such that the Raman spectrum may be dominated by the n2 (CQC) and n1 (C–C) bands (see Figure 20 [50,51]) and there is little evidence of the normal Raman bands expected from PVC. Consequently, different conjugation sequence lengths may be probed using different excitation laser wavelengths. By taking advantage of the sensitivity of the resonance Raman effect, low levels of degradation may be detected enabling such as the early stages of weathering to be monitored [26,51]. The polyenes may be detected at levels of o0.00001%. However, on solid samples, one must be careful about laser power densities used in a study; if the laser power is too high or the exposure time to the laser too long then one may obtain false results [52]. Another valuable advantage of Raman spectroscopy, which is unique, is its capability of being used to characterise carbon species, in particular graphitic and amorphous carbon; this can be of value to many degradation and pyrolysis studies. Perfectly ordered graphite is characterised by a Raman-active vibrational mode that occurs at 1,575 cm1; this band is usually referred to as the ‘G’ band. With increasing disorder in the carbon, a new band, the ‘D’ band, appears at
416
John M. Chalmers and Robert J. Meier
Figure 20 Raman scattering from PVC thermally degraded at 801C. The excitation laser was 514 nm; the degradation time in minutes is indicated above each spectrum. Reproduced form Everall [51]. r, with kind permission of Springer Science and Business Media.
ca. 1,330 cm1 (because of resonance effects, the position of the band maximum of the D band may be shifted, and its half bandwidth change). In a study of the structural and conductivity changes during the pyrolysis of polyaniline (PANI), Trchova´ et al. [53] used both mid-IR and Raman spectroscopies to examine PANI samples that had been exposed in air to temperatures between 1001C and 1,0001C for 2 h. Figure 21 shows the progression of a PANI sample (1.5 g) to carbonaceous graphite-like material as it was exposed in a porcelain crucible in ambient atmosphere for 2 h to elevated temperatures in a furnace. In another joint vibrational spectroscopy study, in combination with X-ray diffraction (XRD), both Raman and infrared spectroscopies were used to characterise the formation of carbonaceous materials derived from polyparaphenylene (PPP) in argon gas for increasing treatment times (up to 6 h) at 7001C [54]; also studied was the effect of different atmospheres. The Raman spectra of the most degraded samples resembled that of weakly graphitised carbon, and a progression to this end through the series of examinations made, whereas, little change was observed in the XRD patterns after initial loss of crystallinity within 0.5 h. In the FTIR spectra recorded from KBr discs a quasi-total disappearance of all bands due to PPP was observed in the spectra of PPP pyrolysed at 7001C for 6 h. Both XRD and Raman spectroscopy were also used in a complementary study of the formation of glassy- or amorphous-like carbon materials as a consequence of the carbonisation of a cured resol-type phenol-formaldehyde resin [55]. In one other example, Raman spectroscopy was employed along with FTIR spectroscopy, XPS, elemental analysis, TGA, SEM and transmission electron microscopy (TEM) to follow the compositional and structure variations of polymethylsilsesquioxane samples pyrolysed at different temperatures in an atmosphere of nitrogen [56]. At 9001C the main product was silica, with formation too of some silica oxycarbide and amorphous carbon, with Raman spectroscopy showing complementary evidence for presence of both the minor species.
Polymer Degradation and Oxidation: An Introduction
417
Raman spectra (488 nm)
T (°C)*
Intensity
20
100
200 300
400 600 800 1000
2000
1500 Wavenumber, cm-1
1000
Figure 21 488 nm excitation Raman spectra of PANI exposed to elevated temperatures for 2 h. Reprinted from Trchova´ et al. [53]. Copyright 2006, with permission of Elsevier.
Raman microscopy offers a much higher lateral spatial resolution than that attainable with FTIR microscopy; 1–2 mm lateral spatial resolution may be achieved with Raman microscopy. In addition, Raman microscopes, because of their confocal capability, have the capability to undertake depth-profiling measurements [57]. Confocal Raman microscopy was one of the tools used in a study of the natural photo-ageing of LDPE [58]; DSC and AFM were the other techniques employed. Raman spectroscopy was used to highlight differences between the surface and sub-surface morphology (crystalline vs amorphous character of the regions). Kim et al. [59] used Raman microscopy to investigate the electrical degradation of triarylamine-based light-emitting polymer diodes. A gradual irreversible oxidation of the blue-emitting conjugated polymer was indicated by the spectral evolution. A study of the degradation of a biodegradable composite periodontal membrane was the subject of investigations using both Raman and mid-IR
418
John M. Chalmers and Robert J. Meier
spectroscopies by Taddei et al. [60,61]. The formulation consisted of a commercial biodegradable poly(e-caprolactone)-poly(oxyethylene)-poly(e-caprolactone), PCL-POE-PCL, block copolymer composite membrane containing hydroxyapatite (HA). The in vitro degradation (weight loss) was undertaken in alkaline and physiological solutions [60]; enzymatic degradation has also been followed [61]. The researchers established that in all media the POE undergoes degradation preferentially, and that bands attributed to the HA component decrease with time, and that the HA is removed faster than the polymer by the degradation media.
3.3 UV/fluorescence/phosphorescence/visible spectroscopy These techniques, all of which involve transitions between electronic energy levels, have to greater or lesser extents, as appropriate, found uses in monitoring the effects of degradation and oxidation on polymers. The high sensitivity of UV (and visible) spectroscopy to chromophores involving p-electron systems makes it particularly sensitive to monitoring conjugated double bonds. This attribute was used to advantage in a study of polyene formation in PVC stabilised with pre-heated metal stearates [62]. The evaluations were conducted on series of samples that consisted of PVC that had been doped with 3 phr (parts per hundred) of the stearates (metal soaps). One series contained non-pre-treated stearates, other series contained stearates that had been previously thermally treated at different temperatures for set periods of time (5, 10, 15 and 20 min). Before UV spectroscopic analysis, the samples were extracted and filtered to give clear solutions for the UV analysis. After this UV analysis, the samples were treated with NaBH4 in order to reduce carbonylic groups, and then UV spectra were recorded from each sample again. This analysis formed part of a sequence of analyses aimed at elucidating an anomalous behaviour2 that had been observed when pre-heated metal soaps were used as stabilisers. Previous studies on these materials included one in which the primary analytical technique was visible reflection spectroscopy (supported by UV spectroscopy) [63], one which used fluorescence emission spectroscopy [64] and one which used mid-IR spectroscopy [65]. In the UV spectroscopic analysis [62], absorbance values at 273 and 360 nm were used to determine the concentrations of polyenes of 3 and 5–7 double bond conjugations, respectively, and their ratio (273/360) used as an indicator of polyene distribution. Important differences in polyene formation trends were observed between the reduced and non-reduced samples, which highlighted a limitation of using the UV-procedure in isolation, since carbonylic groups formed as sideproducts during the thermo-oxidation of PVC and apparently attached to the 2
Unexpected behaviour was observed when calcium stearate (CaSt2) and zinc stearate (ZnSt2) were pre-heated at temperatures of 1001C, 1301C, 1501C and 1801C and then added as stabilisers to PVC. Pre-heated CaSt2 reduced the induction time to dehydrochlorination, whereas pre-heated ZnSt2 prolonged the induction time. When both soaps were pre-heated together the induction times to dehydrochlorination and hence discoloration of PVC was significantly extended [65].
Polymer Degradation and Oxidation: An Introduction
419
polyenes, appear to shift the absorption maximum of specific conjugations, and thereby alter quantification. For normal stabilisation involving 3 phr of calcium and zinc stearates (ratio 1:2), this was not problematic, since the evolution of polyenes was very similar before and after reduction by NaBH4, but the stabilisation was affected by a mixture of the metal soaps that had been pre-heated, the carbonylic groups formed exerted an enormous influence on polyene trends. (Full details of the conclusions may be found within the references cited.) Fluorescence and UV spectroscopy were tools used in a multi-technique comparison of the photochemical and thermal degradation of two polycarbonates; the other techniques and tests applied included: detection of hydroperoxides by an iodometric method, derivatisation with SF4 and NH3 coupled with mid-infrared spectroscopic analysis to identify carbonyl species, midinfrared spectroscopy to profile degradation species through degraded film samples, high-performance liquid chromatography (HPLC) analysis of extracted low molecular photo-products, size exclusion chromatography (SEC) to determine average molecular weights and polydispersity, and density to determine cross-linking [66]. The two polymers were a bisphenol-A-polycarbonate (PC) and a trimethylcyclohexane-polycarbonate (TMC-PC); they were irradiated at short wavelength (l ¼ 254 nm) and under polychromatic light (lW300 nm) in the absence of presence of oxygen or thermo-oxidised at 1701C. As a small example of this extensive study into the different behaviour of these two polycarbonates, and to illustrate the complementary comparisons of some of the studies undertaken, Figure 22 compares some of the UV and mid-IR spectra reported for the photolysis part. These were described in terms of photo-Fries rearrangements. In the early stages of photolysis, characterised by a main UV absorption peak at 320 nm and a carbonyl peak at 1,689 cm1, a primary photo-Fries product occurs, which reaches a photo-stationary concentration, this then photo-rearranges into a product that accounts for development of the bands at 355 nm (UV) and 1,629 cm1 (mid-IR) in PC. However, while this mid-IR band develops in TMC-PC, the UV-band at 355 nm is not observed. Part of the explanation for this difference lay in development of other species that are formed competitively to the photo-Fries rearrangement, which account for the yellow colour of the sample after irradiation; absorption resulting from these species leads to an unstructured absorption that progressively overlaps the other bands. The concentration of photo-Fries products and yellowing species can be seen when comparing the variation in absorbance values at 1,689 and 1,629 cm1 (mid-IR) with that at 450 nm (UV) (see, e.g., Figure 22(b)). TGA, iodometric, mid-IR, luminescence (fluorescence and phosphorescence) and colour formation (yellowness index according to standard method ASTM 1925) were all employed in a study of aspects of the thermal degradation of EVA copolymers [67]. Figure 23 compares a set of spectra from the luminescence analysis reported in this work. In the initial spectra (Figure 23(a)) of the EVA copolymer, two excitation maxima at 237 and 283 nm are observed, which both give rise to one emission spectrum with a maximum at 366 nm; weak shoulders
420
John M. Chalmers and Robert J. Meier
2
TMC-PC 1
0 300
344h 52h 5h 0.25h
400 500 Wavelength (nm)
0,08 ΔOD at 1629 cm-1
Absorbance
PC
600
PC
0,06 TMC-PC 0,04 0,02 0,00 0,00
0,05 0,10 ΔOD at 450 nm
(a)
0,06 0,04 0,02
0,06 Absorbance
Absorbance
(b) 344h 115h 52h 26h 12h 5h 2h 0.75h 0.25h
PC 0,08
0,15
344h 115h 52h 26h 12h 5h 2h 0.75h 0.25h
TMC-PC
0,04 0,02 0,00
0,00 1700 1660 1620 1580 1540 Wavenumbers (cm-1) (c)
1700 1660 1620 1580 1540 Wavenumbers (cm-1) (d)
Figure 22 Photolysis at 254 nm for various photolysis times. (a) Changes in UV spectra (subtraction, irradiated sample spectrum minus non-irradiated sample spectrum): PC film (_______); TMC-PC (——————); (b) increase of mid-IR absorbance at 1,629 cm1 vs absorbance at 450 nm for PC and TMP-PC films; (c) irradiated minus non-irradiated mid-IR spectra for PC film; (d) irradiated minus non-irradiated mid-IR spectra for TMP-PC film. Reprinted from Rivaton et al. [66]. Copyright 2002, with permission from Elsevier.
are also seen at 460 and 495 nm. (This spectrum is similar to that previously reported for polyethylene. The fluorescence excitation at 237 nm may be assigned to a CQC pp transition, that at 283 nm to a weaker ketone pp transition; both originate from the presence of a,b-unsaturated carbonyl species of impurities.) As can be seen in Figure 23(b), excitation at 239 nm produces a broad long wavelength emission, with peak maximum at 390, 421 and 437 nm, consistent with the formation of polyene sequences. However, excitation at 300 nm (see Figure 23(c)) produces the same emission as was observed in the control (cf. Figure 23(a)). This emission is therefore associated with the a,b-unsaturated carbonyl species; the emission at 361 nm is due to longer polyconjugated ketones. The fluorescence spectra recorded from a sample degraded for 2h (see Figure 23(d)) are consistent with further polyconjugation. The potential of using extrinsic (fluorescent) probes for monitoring the initial stages of oxidation was explored for the photo-oxidation of a UV-cured aliphatic polyurethane-acrylate-based adhesive [68]. The two probes investigated were: p-dimethylamino salicylic acid (p-DASA) and 2u,7u-difluorescein (Oregon Green
Polymer Degradation and Oxidation: An Introduction
100
EMISSION 50
RELATIVE INTENSITY
RELATIVE INTENSITY
75 EXCITATION
Excitation
Emission 50
25
300 400 Wavelength / nm
400 300 Wavelength / nm
(b)
Emission
Excitation
40
20
400 500 300 Wavelength / nm (c)
RELATIVE INTENSITY
(a) RELATIVE INTENSITY
421
60
Emission
Excitation
40
20
300 400 Wavelength / nm (d)
Figure 23 Fluorescence excitation and emission spectra. (a) virgin EVA sample (excitation ¼ 280 nm; emission ¼ 360 nm); (b) EVA sample degraded for 1 h at 1801C (excitation ¼ 239 nm; emission ¼ 390 nm); (c) EVA sample degraded for 1 h at 1801C (excitaton ¼ 301 nm; emission ¼ 361 nm); (d) EVA sample degraded for 2 h at 1801C (excitation ¼ 238 nm; emission ¼ 388 nm). Reprinted from Allen [67]. Copyright 2000, with permission from Elsevier. (This figure has been reproduced from the original in reference [67], however it would appear that the labels ‘‘excitation’’ and ‘‘emission’’ have been incorrectly inserted and should be switched for parts (b), (c) and (d).)
488, OG). For the fluorescent studies, excitation wavelengths were set at the maximum absorption of the fluorescent probe in the cured adhesive. As can be seen from Figure 24(a) and (b), the fluorescence emission from the cured resin decreases with increasing photo-ageing (UV-irradiation centred at 365 nm); this is accompanied by a slight blue shift of the maximum fluorescence wavelength. This quenching of the fluorescence with increasing photo-ageing correlates very well with the CL intensity determined from ageing of the adhesive without the fluorescent probes being added, implying that the kinetics associated with the formation of the species that quench fluorescence and produce CL are intimately
John M. Chalmers and Robert J. Meier
600
Fluorescence intensity (a.u.)
Fluorescence intensity (a.u.)
422
0h 1h 9h 24 h 63 h
500 400 300 200 100 0 350
400 450 500 Wavelength (nm) (a)
550
1000
600 400 200 0 500
600
p-DASAIn(λz382/355) OG (Imax)
0 100 200 300 400 500 600 700 800 lCL (mV) (c)
Fluorescence intensity (n.u.)
Fluorescence intensity (a.u.)
2.2 2.6 2.4 2.2 2.0 1.8 1.6 1.4 1.2 1.0
0h 3h 6h 24 h 63 h
800
550 600 650 Wavelength (nm) (b)
700
OG (Imax) p-DASA (382/355)
2.0 1.8 1.6 1.4 1.2 1.0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 νCL .104 (mV-1/2-s-1) (d)
Figure 24 (a) and (b) Fluorescence spectra from extrinsic probes in cured adhesive under different photo-ageing times, (a) p-DASA, (b) OG. (c) and (d) Fluorescent intensity of OG and p-DASA as a function of (c) CL-intensity at the maximum signal (d) CL-decay rate. Reprinted from Peinado et al. [68]. Copyright 2002, with permission from Elsevier.
related [68]. Thus, in this case, a fluorescent probe can be successfully used to follow the early stages of oxidation, which was not possible here with mid-IR spectroscopy because of its lack of sensitivity.
3.4 Mass spectrometry Mass spectrometry (MS) coupled with pyrolysis has been a key technique in detecting the thermal degradation products of polymers, and thereby elucidating their thermal decomposition pathways [69]. In pyrolysis-MS, a sample is thermally decomposed in a reproducible manner by a pyrolysis source that is interfaced with a mass spectrometer. The volatile products formed can then be analysed either as a mixture by MS or after separation by GC/MS [70]. Pyrolysis GC/MS is limited in application to those studies in which the compounds formed are capable of being analysed by GC, that is it is only reasonably suitable for low molecular weight products. Many synthetic polymers degrade (pyrolyse) by processes that may simply be described as either random scission (e.g., polyolefins), unzipping to produce mostly monomers (e.g., PMMA)
Polymer Degradation and Oxidation: An Introduction
423
Figure 25 Total ion chromatogram (pyrogram) of PVC. Reproduced with permission from Wampler [71]. r 2005, Perkin Elmer, Inc.
or side-group elimination (e.g., PVC). Figure 25 shows a GC electron impact (EI)-MS total ion chromatogram (pyrogram) obtained from PVC; peaks labelled 1–5 were identified as HCl, benzene, toluene, xylene and naphthalene, respectively [71]. Montaudo and co-workers have used direct pyrolysis mass spectrometry (DPMS) to analyse the high-temperature (W5001C) pyrolysis compounds evolved from several condensation polymers, including poly(bisphenol-A-carbonate) [69], poly(ether sulfone) (PES) and poly(phenylene oxide) (PPO) [72] and poly(phenylene sulfide) (PPS) [73]. Additionally, in order to obtain data on the involatile charred residue formed during the isothermal pyrolysis process, the pyrolysis residue was subjected to aminolysis, and then the aminolyzed residue analysed using fast atom bombardment (FAB) MS. During the DPMS measurements, EI-MS scans were made every 3 s continuously over the mass range 10–1,000 Da with an interscan time of 3 s. As an example of the form of the information that may be derived from a pyrolysis-MS, Figure 26 [69] shows the structure of the polycarbonate (PC) and the EI-MS spectra of pyrolysis compounds obtained by DPMS of poly(bisphenol-A-carbonate) at three different probe temperatures corresponding to the three TIC (total ion current) maxima shown in Figure 27(b); Figure 27 compares the MS-TIC curve with those obtained from thermogravimetry. (The TIC trace is the sum of the relative abundances of all the ions in each mass spectrum plotted against the time (or number of scans) in a data collection sequence [70].) Figure 27 shows that the PC is stable up to about 4001C; the maximum rate of polymer degradation occurs at 5001C; a residue of 20% remains at 8001C [69]. In the degradation step occurring at 5001C some of the many ions (m/z) that may be identified are: phenol at 94; methylphenol at 108; isopropylidenephenol,
424
John M. Chalmers and Robert J. Meier
O
CH3 O
O C CH3
213
100
n
405
x5 380°C
(a)
508
1% 228
747 762
449 493 703
44
100
200
300
400
500
m/z 800
700
600
94
100
213 1% 44
0
554
344 250 303 330 358 423 464 228238 276 370 438 318 210 372 264
108 120 134
200
100
(b)
449 x25
x5
300
400
540 566
580 606
500
m/z
600
94
100
x5
91
1% 18
x10
432 446456 314 418 328 460 300 326 236 404 340 210 238 390 354 342 264 196 470 474 388 250 286 488 508 181
550 °C
(c)
224
108
120 134
m/z 0
50
100
150
200
250
300
350
400
450
500
550
600
Figure 26 Structure of PC and EI mass spectra of pyrolysis compounds obtained by DPMS of poly(bisphenol-A-carbonate) at probe temperatures of (a) 3801C, (b) 5001C and (c) 5501C. Reprinted with permission from Puglisi et al. [69]. Copyright 1999, American Chemical Society.
Thermogravimetry
DPMS 100
PC
PC 1%
Residue %
100
0
0 100 200 300 400 500 600 700 800 Temperature /°C (a)
100
200
300 400 500 600 Temperature /°C (b)
700
800
Figure 27 (a) Thermogravimetry (TG) and derivative TG (DTG) curves of poly(bisphenol-Acarbonate) (PC); (b) total ion current (TIC) DPMS of PC. Reprinted with permission from Puglisi et al. [69]. Copyright 1999, American Chemical Society.
Polymer Degradation and Oxidation: An Introduction
425
134; bisphenol A, 228; p-sub-diphenyl ethers, 210 and 250 with one and two isopropylidene end units, respectively; ethers containing an intact bisphenol A unit at 318, 332 and 438; compounds with xanthone units at 276, 358, 370 and 372; compounds with two xanthone units at 580 and 606 and compounds containing both xanthone and ether units at 540 and 554. The TIC curve and time–temperature resolved profiles of some of these molecular ions are shown in Figure 28. 100
TIC
I%
(a)
0 100
CH3
I%
m/z 508
(b)
O
O CO 2
CH3
0 100 I%
(c) CO2
m/z 44
0 100
(d)
I%
OH m/z 94
0 100 O
I%
CH3
(e)
m/z 370
HO CH3
O
0 100 I%
CH3 HO
(f)
m/z 318
O
CH3
CH3
0 100
CH3
I%
H3C
(g)
O O
m/z 418
CH3 C2H5
0 100
(h)
I%
CH3 CH3
0 100
200
C3H7
m/z 340
O
300
400 500 Temperature (°C)
600
700
800
Figure 28 TIC plot and the time–temperature resolved profiles of some molecular ions recorded obtained from the DPMS of PC. Reprinted with permission from Puglisi et al. [69]. Copyright 1999, American Chemical Society.
426
John M. Chalmers and Robert J. Meier
CH3
a.
O
O CO CH3
O
c.
O CO O
O - CO - O CH3
O CO CH3
CH3
n
CH3
b.
Intramolecular Exchange
+H2O −CO2
n
CH3 O
OH CH3
CO2 Elimination (1-3 Shift)
O
Dehydrogenation
O
CH3
d.
Diaproportionation CH-Transfer
+
CH3
CO
e.
O CO O
Isomerization -H2O
O
CO
Figure 29 Thermal degradation process occurring in PC. Reprinted with permission from reference 69. Copyright 1999, American Chemical Society.
Interrogation of the data shown in Figures 26–28 enables one to construct probable thermal degradation processes, such as those shown in Figure 29. Direct insertion probe pyrolysis mass spectrometry (DPMS) utilises a device for introducing a single sample of a solid or liquid, usually contained in a quartz or other non-reactive sample holder, into a mass spectrometer ion source. A direct insertion probe consists of a shaft having a sample holder at one end [70]; the probe is inserted through a vacuum lock to place the sample holder near to the ion source of the mass spectrometer. The sample is vaporized by heat from the ion source or by heat from a separate heater that surrounds the sample holder. Sample molecules are evaporated into the ion source where they are then ionized as gas-phase molecules. In a recent study, Uyar et al. [74] used such a device for studying the thermal stability of coalesced polymers of polycarbonate, PMMA and poly(vinyl acetate) (PVAc) [75] and their binary and ternary blends [74] obtained from their preparation as inclusion compounds in cyclodextrins. Pyrolysis-MS, together with TGA analysis, was chosen recently as the technique with which to investigate the thermal behaviour of two polythiophene copolymers, since insolubility in common solvents of conducting polymers limits
Polymer Degradation and Oxidation: An Introduction
427
the ready application of several other spectroscopic techniques [76]. In this application, diagnostics of the pyrolysis-MS data were used to show that two conducting polymers prepared from thiophene with two different comonomers by electrochemical synthesis were copolymers containing ester linkages, and that these enhanced thermal stability over the polythiophene homopolymer. Although both GC/MS and DPMS are limited to detecting compounds of relatively low masses produced by pyrolysis, matrix-assisted laser desorption (MALDI) time-of-flight (ToF) mass spectrometry offers the possibility of detecting oligomers in excess of 30,000 Da [77]. Montaudo and co-workers have complemented their earlier DPMS study (see earlier) [69] with a MALDI-ToFMS study of PC thermal oxidation [78]. In this latter study, the researchers used a combination of SEC, 1H nuclear magnetic resonance (NMR) spectroscopy, MALDI-ToF-MS and SEC/MALDI-ToF-MS to elucidate the mechanisms of thermal oxidation of two PC samples capped with different end-groups. Additionally, these workers have used MALDI-ToF-MS to determine the structure of molecules produced in the photo-oxidative degradation of Nylon 6 films at 601C in air [79]. Such studies reveal the size, chemical structure and endgroups of molecules originating during the degradation processes. These enable for discrimination among possible oxidation mechanisms. The data from the nylon 6 photo-oxidative study led to conclusions that included that five and four oligomers originated from Norrish type I and Norrish type II chain-cleavage reactions, respectively, and nine peaks in the spectra originated from hydroperoxide decomposition reactions [79]. Other reported studies by this group have included MALDI-ToF-MS investigations of: photo-oxidation of nylon 6,6 [80]; photo-oxidation of the aliphatic polyester, poly(butylene succinate) [81]; thermaloxidation [82] and both photo- and thermal-oxidation processes in poly(ether imide) [83]. Since the MALDI approach requires a solution of a polymer to be mixed with a solution of the matrix material, a limitation of the MALDI-ToF-MS technique is that it only analyses the soluble part of the polymer residue generated in the degradation process. [77]. DPMS and MALDI-ToF-MS may be seen as complementary approaches [77]; while the former technique, being essentially on-line, may supply information on less thermally stable products and on volatile compounds at temperatures at which the pyrolysis residue becomes insoluble, it has to be undertaken in vacuum; therefore, the off-line MALDI approach can be considered as being applied to polymers that have experienced more realistic real world conditions. In a separate report of their work on the thermal oxidation of PC at 3001C and 3501C, Montaudo and co-workers used MALDI-ToF-MS to examine off-line fractions separated by SEC [84]. Figures 30 and 31 are examples from this study. Figure 30 compares SEC traces of the tetrahydrofuran (THF) soluble portions of unoxidised PC and PC thermally oxidised (in air) at 3001C; also noted are some of the positions from which fractions were collected for subsequent MALDI-ToF-MS examination. At 3001C, up to 120 min, the insoluble in THF residues were 3%, while after 180 min they were 7%. Figure 31 shows a MALDI-ToF-MS of a SEC fraction collected at 25.5 Ve ml of the PC sample oxidised at 3001C (fraction noted 43 on Figure 30). The MALDI peaks identified as expanded plots in the insets of Figure 31 and
428
John M. Chalmers and Robert J. Meier
Fraction 43 Fraction 52 Fraction 55 T=300°C Fraction 64 0 minutes 180 minutes
16
18
20
22
24 26 Ve(mL)
28
30
32
34
36
Figure 30 SEC (THF solubles) traces of unoxidised PC and PC thermally oxidised at 3001C for 180 min. Reprinted from Montaudo et al. [84]. Copyright 2002, with permission from Elsevier.
16000
D
D
4318
D
4572
4827
D
14000
4318
G
D
4572
D
12000
4827
G
C
C
4438
4692
C 4947
10000
8000
D
D
D 4300 4400 4500 4600 4700 4800 4900 5000 Mass (m/z)
C
9014
D
9402
9148
8894
C 9268
9653
C 9522
D 9911
C
9778
D
6000
D 9148
9402
D 9656
4000 9000 9200 9400 9600 9800 Mass (m/z) +10
2000
2000
4000
6000
8000 10000 12000 14000 16000 18000 20000 22000 24000 26000 Mass (m/z)
Figure 31 MALDI-ToF mass spectrum of a SEC fraction (fraction 43, see Figure 30) from a PC sample oxidised at 3001C. Reprinted from Montaudo et al. [84]. Copyright 2002, with permission from Elsevier.
Polymer Degradation and Oxidation: An Introduction
CH3
O
C
O
C
OH
O CH3 O
CH3
D
H
O
O CH3
G
O
C
C
OH
O CH3
n
O
n
CH3
CH3
O
429
O O
CH3
C
O
CH2OH
n
Figure 32 Structural assignments of oligomers determined from MALDI-ToF-MS spectra shown in Figure 31. Reprinted from Montaudo et al. [84]. Copyright 2002, with permission from Elsevier.
labelled C, D and G, are associated with oligomers, the assignments of which are given in Figure 32. When the experiment was conducted at 3501C, the THF insoluble residues after 75 min exceeded 23%, because of the extent of oxidation, most of the oxidised species were already cross-linked, thereby being incapable of being examined by MALDI-ToF-MS; SEC fractions that were capable of being examined by MALDI-ToF-MS of this more oxidised sample contained mostly very low oligomers of which only a few peaks corresponded to oxidised species.
3.5 Nuclear magnetic resonance spectroscopy NMR spectroscopy, in particular solid-state NMR spectroscopy, can provide both confirmatory and complementary information to that realised by other techniques, as well as providing unique insight into the chemical processes involved with polymer oxidation/degradation. Solution-state NMR can be used to both distinguish between various species formed at the early stages of degradation and to identify and quantify these [85], and to characterise soluble extracts. Solid-state NMR can be used to probe key structural changes on the polymer material or network occurring as a consequence of degradation. In an NMR measurement, the nuclei of atoms possessing a nuclear spin of 1/2 (or 3/2, 5/2, etc.), such as a proton in 1H NMR, which have two possible orientations [85], are split by a magnetic field, with the lower energy level containing slightly more nuclei than the higher energy level; the magnetic moments of these spins are aligned (parallel) with and opposed (anti-parallel) to the applied magnetic field, respectively, and have a small energy difference occurring in the frequency range 20–900 MHz. (The initial populations of these energy levels are governed by thermodynamics (Boltzmann distribution); see, e.g., Ref. [85].) Irradiation of the sample in an appropriate magnetic field by a
430
John M. Chalmers and Robert J. Meier
radiofrequency pulse at 901 to the magnetic field that is equal to the energy difference between the energy levels of the nuclei will cause excitation of the lower energy nuclei to the higher energy level; an absorption of energy of this radiofrequency gives rise to a characteristic NMR resonant peak. Nuclei excited to the higher energy state relax to the lower energy state by two major (nonradiative) processes known as spin-lattice (longitudinal) relaxation and spin–spin (transverse) relaxation. In the former, denoted as T1, nuclei lose energy to the sample (the lattice may be considered as the molecule and its environment/ surroundings; thus T1, which depends on lattice mobility, is short for liquids, but longer for solids; it shortens when solids are heated and become viscous); T2, the spin–spin relaxation time, involves interaction (relaxation process) between neighbouring spins and yields information about the local fields experienced by the nuclei, that is its chemical nature and environment, for example, in 1H NMR it depends on the mobility of the protons [85]. A few relatively recent published examples of the use of NMR spectroscopy for studying polymer degradation/oxidation processes will now be discussed briefly. At the early stages of degradation, the technique can be used to provide chemical identification and quantification of oxidised species; for polyolefins, oxidation sites can be identified by the chemical shifts of –CH2– groups a and b to carbons bonded to oxygen [85]. Spin–spin relaxation times may be determined by a pulse sequence known as the Hahn spin-echo pulse sequence. 1 H-NMR T2 measurements were employed in a combined (NMR, DSC, midinfrared and mechanical properties) investigation of aged cross-linked polyolefin cable insulation commonly used in power cables [86]. The polymer matrix was an EVA copolymer; the formulation also contained a low level of TiO2 and flameretardants, and its cross-linked content was estimated at 65%. Some samples were artificially aged in convection ovens operating at different temperatures, other samples were exposed to Co60 radiation. Part of the study was on selecting an appropriate solvent with which to swell samples such that there was a reasonable separation between the T2 values measured from unaged and aged samples; in the absence of solvent the T2 relaxation values for the unaged and aged samples were very similar, yet the decrease in ultimate elongation time was considerable. Therefore, in this study, NMR relaxation time was shown to be insensitive to degradation changes in unswollen samples. However, when appropriately swollen with d6-benzene the 1H T2 relaxation times determined by NMR correlated well with the mechanical property (tensile) measurement for the thermally aged samples, although not for the irradiated samples (see Figure 33). In an NMR analysis of the effects of g-irradiation induced degradation on a specific polyurethane (PU) elastomer system, Maxwell and co-workers [87] used a combination of both 1H and 13C NMR techniques, and correlated these with mechanical properties derived from dynamic mechanical analysis (DMA). 1H NMR was used to determine spin-echo decay curves for three samples, which consisted of a control and two samples exposed to different levels of g-irradiation in air. These results were deconvoluted into three T2 components that represented T2 values which could be attributed to: an interfacial domain between hard and soft segments of the PU, the PU soft segment, and the sol
Polymer Degradation and Oxidation: An Introduction
431
20 100 C 110 C 125 C 155 C Irradiated
10
1H
T2 (ms)
15
5
0 0
50
100
150 200 250 Ultimate Elongation (%)
300
350
400
Figure 33 Correlation of T2 from 1H NMR with ultimate elongation (tensile) measurement for thermally aged samples at the indicated temperatures, and for 221C g-irradiated at 200 Gy/h. Reproduced from Harris et al. [86]. Copyright 2003, John Wiley & Sons, Inc.
fraction of the polymer. Because the 1H NMR measurement was limited to interpulse delays of 50 ms or greater, a 13C NMR experiment was performed to measure T2 for the PU hard segments. With increased exposure to g-irradiation, a steady decrease was determined for both the T2 values of the interfacial domain and the soft segment, but no change was observed for the sol fraction. Figure 34 compares the DMA plot and the 1/T2ave value as a function of the DMA determined equilibrium storage modulus Gu, where 1/T2ave is the bulk averaged transverse relaxation time. It shows: 1/T2avepGu2. The results are consistent with morphological changes expected to occur as a consequence of radiation-induced chain scission. Figure 34 also shows example spectra from a 13C [1H] crosspolarisation magic angle spinning (CPMAS) NMR experiment; CPMAS NMR was used, along with DSC data, to deduce that exposure to less than 100 kGray did not lead to significant damage to the PU hard segment. In a combined elemental microanalysis (to determine the C, H, N and Cl contents of char), TGA, DSC, mid-infrared and NMR study of the char forming process in polychloroprene, CPMAS solid-state 13C NMR was used to probe for structural changes that occurred during the degradation steps [88]. The NMR study supplied both valuable extra detail and confirmatory and complementary information. It was observed that while the dehydrochlorination of polychloprene proceeded, there was loss of sp3-hybridised carbon and commensurate
432
John M. Chalmers and Robert J. Meier
Figure 34 Left: (a) equilibrium storage modulus Gu as a function of g-irradiation dose determined from DMA experiments on exposed PU samples; (b) 1/T2ave as a function of Gu. Right: 13C CPMAS NMR measurements on non-irradiated PU sample: (a) 3 ms, (b) 0.5 ms, and (c) 100 ms. SS denotes soft segment; HS denotes hard segment. Reprinted from Maxwell [87]. Copyright 2003, with permission from Elsevier.
growth of sp2 carbon, and of particular note was that in the latter stages of oxidation 50% of the sp2 hybridised carbons were non-protonated. Since Cl microanalysis showed the near complete absence of residual chlorine, the observation indicated the presence of condensed aromatic structures formed by intramolecular cyclisation, see Ref. [88] for full details. Solid-state 1H and 19F MAS NMR variable temperature techniques (together with DSC analysis) have been employed recently in an investigation of the ageing mechanisms of a vinyl chloride-chlorotrifluoroethylene (VC/CTFE) copolymer due to exposure to g-irradiation [89]. In this preliminary study, significant degradation was seen in the VC region of the copolymer by 1H NMR, while in the 19 F NMR measurement negligible changes were seen in the CTFE block. Additional effects of oxygen on the degradation processes were seen in the NMR VC region when spectra from samples irradiated in air and nitrogen were compared. (The authors claim that a more complete analysis of radiation- and thermally induced degradation is underway, which additionally will involve solution-state NMR and GC/MS for elucidating the degradation products and corresponding off-gassing products).
Polymer Degradation and Oxidation: An Introduction
433
In a final example in this section of the role of NMR, the technique in combination with Mo¨ssbauer spectroscopy and ATR-infrared spectroscopy was used in a study to investigate room-temperature-vulcanised (RTV) siloxane foams [90]. The study compared aged in service (5–27-year-old) foams with those from an artificial aging (an accelerated aging process). The commercial product is cured by condensation reactions catalysed by tin octoate. In this study for the aged-in-service foams: 19Sn Mo¨ssbauer spectroscopy was used to investigate the temporal changes in tin residues, solid-state 29Si NMR was used to examine the network structure of the RTV network, and high-resolution solution-state 1H NMR was used to examine CDCl3 extracts. Solid-sate 29Si NMR was used to differentiate the various functional linkages in the foams, which showed no significant change in the di- to trifunctional linkage ratios. 1H NMR on the solvent extracts revealed the presence of water, catalyst, plasticiser and some small silicone oligomers, the latter being associated with degradation of the foam. For the artificially aged foams, ATR-infrared spectroscopic data, coupled with a multivariate curve resolution data analysis routine, was used to probe the effects various environmental factors may have on a foam surface. Some of the variables explored in the artificially aged set were moisture level, g-irradiation dose, tin catalyst level and plasticiser content.
3.6 X-ray photoelectron spectroscopy and secondary ion mass spectrometry XPS and SIMS are both surface sensitive and surface-specific techniques that may be used to probe surface oxidation/degradation of polymers. They use X-rays and ions, respectively, to characterise surface species. Both XPS and SIMS are operated under ultra-high vacuum, UHV, conditions.
3.6.1 X-ray photoelectron spectroscopy XPS or ESCA (electron spectroscopy for chemical analysis) is a surface sensitive technique that only probes the outer atomic layers of a sample. It is very useful tool to study polymer surfaces [91]. An XPS spectrum is created by focusing a monochromatic beam of soft (low-energy) X-rays onto a surface. The X-rays cause electrons (photoelectrons) with characteristic energies to be ejected from an electronic core level. XPS, which may have a lateral resolution of ca. 1–10 mm, ˚ of a surface. probes about the top 50 A Storp and Bock [92], in an almost seminal paper on physical characterisation of early recognition of photodegradation in polymer films, applied UV absorption spectrometry, IR spectroscopy, XPS and ESR. The text, which is in German, although not leading to any definite conclusions at that time, was an early and very interesting multi-technique study on the degradation of polymer coatings. This was later followed by, e.g., other more extensive work involving ESR (see Chapter 12). Scierka et al. [93] reported on the difference in chemical changes, as studied by XPS, in an epoxy system with and without TiO2 pigment. Whereas the concentration of the pigment seemed to have no influence, the type of pigment
434
John M. Chalmers and Robert J. Meier
did. In a series of publications, Wang, Wilkie and co-workers have reported on the use of XPS to study the thermal degradation of polymer-clay nanocomposites: polystyrene [94,95], PMMA [95,96] and PVC [97]. The investigations were related to the fire-retardant/charring properties of the materials. As an example, the thermal degradation process of the polymer nanocomposites [95] was explained by either aluminosilicate migrating to the surface or possible loss of carbon in the surface layer, thus forming a barrier that then protects the underlying polymer. Upadhyay et al. [98] used primarily correlated XPS and water contact angle measurements to study the surface degradation and recovery of amorphous films of a PMMA and a poly(aryl ether ether ketone) (PEEK). Surface modification of the films was carried out in a dielectric barrier discharge (DBD) unit, samples being treated with different dose levels of dielectric discharge. The modified (treated) samples were then stored for one month and re-examined. Figure 35 shows C(1s) and O(1s) XPS envelopes and their curve-fitting deconvolutions, O(1s)
C(1s)
C(1s)
C
C
B
C
C
B
B
A
A
B
A
A
294 291 288 285 282 279 540
536
532
528
524 296
292
288
Binding Energy (eV)
284
0.4
75
0.3
65 70
0.2
60 0.1
55 3
Dose (J/cm2)
(c)
4
5
6
0
Contact angle (°)
Contact angle (°)
0.5
80
2
532
528
524
90
0.4
80
0.35
70
0.3
60
0.25
50
0.2
40
0.15
30 20
0.1
10
0.05
0
0
1
2
3
4
5
6
0
Dose (J/cm2)
(d)
Figure 35 Top row: XPS C(1s) and O(1s) band envelopes and curve-fitted components for (a) PMMA and (b) PEEK films: A is untreated, B the DBD-treated at 5.7 J cm2 and C the post-treatment-aged (stored) sample. Bottom row: contact angle and XPS O/C variation of (c) PMMA film and (d) PEEK film: solid lines are for the freshly treated in air DBD samples, the dashed lines are for the post-process-aged films. Reprinted from Upadhyay et al. [98]. Copyright 2005, with permission of Elsevier.
O/C
0.6
85
1
536
(b)
90
0
284 540
Binding Energy (eV)
(a)
50
C(1s)
Polymer Degradation and Oxidation: An Introduction
435
which were used to determine the percentage concentrations of various components. These were for PMMA: 285.0 eV (CxHy), 285.7 eV (C–CO), 286.8 eV (C–O–CO) and 289.03 eV (O–CQO). After treatment PMMA showed a loss of (CxHy) accompanied by a relative increase in C–CO, C–O–CO and O–CQO carbons. Following storage, a loss of C–O–CO functionality and the O–CQO (from the O(1s) envelope) component relative to (CxHy) was identified. After storage, there was almost complete recovery of the (CxHy) component in the C(1s) XPS band envelope, which complemented the angle recovery observed in the contact angle measurement. A similar analysis was performed on the PEEK film (see reference [98] for exact details), which also showed recovery from the hydrophilic modification after storage. The rational for the full observations was that the effect of UV radiation and physical etching within the discharge could account for the degradation of the polymer surfaces. A static SIMS measurement was also performed on the PMMA samples to complement and confirm the XPS observations; problems with attaining a clean surface PEEK film that gave a reproducible mass spectrum precluded the use of SIMS in this instance for additional relevant study. Upadhyay and co-workers have conducted similar investigations on nylon 6,6 film [99] and a poly(ethylene terephthalate) (PET) film [100]. Adhesion of non-polar polymers is sometimes improved by oxidation, so essentially what is normally thought of as degradation may be used to introduce an enhancing surface property. Nevertheless, in both cases the oxidation process modifies the polymer surfaces, and the analysis tools can be rather similar, see, e.g., Ref. [101].
3.6.2 Secondary ion mass spectrometry A SIMS spectrum is created by bombarding a surface with high-energy primary ions. This causes both neutral and charged species to be sputtered (ejected) from the surface. These emitted secondary ions, most commonly the positive ions, are then analysed by a mass spectrometer. Although the mass spectrometer may be either a quadrupole or magnetic sector instrument, for higher sensitivity and greater coverage of mass range, a ToF mass spectrometer is used. Rastering of the ion beam over a surface can be used to generate a molecule or element specific map, which has a lateral spatial resolution of about 40 nm. Information from a surface’s top monolayer is provided in a static SIMS measurement. Dynamic SIMS, which uses higher-energy primary ions, can be used to depth profile a polymer sample over a range of about 1–30 nm. For a ToF-SIMS investigation of the surface oxidative degradation of lowdensity polyethylene (LDPE), the polymer was exposed to 18O2 rather than 16O2 in order to be able to readily discriminate oxygen introduced by the ageing process from that in the polymer prior to ageing [102]. Figure 36 shows an example series of ToF-SIMS spectra from this investigation, which shows the clear separation of the 16O species from the 18O species. In the study, close correlation was observed between the intensity of the 18O carbonyl species determined by mid-infrared spectroscopy with the ToF-SIMS 18 O peak intensity as a function of 18O2 exposure time. ToF-SIMS spectra obtained from microtomed cross-sections showed no
436
John M. Chalmers and Robert J. Meier
Signal
16O
288 hours
18O
144 hours
0 hours
15.9
16.0
17.9 Mass [Dalton]
18.0
18.1
Figure 36 TOF-SIMS 16 O and 18 O peaks after 0, 144 and 288 h oven ageing at 901C. Reprinted from Moller et al. [102]. Copyright 2003, with permission of Elsevier.
concentration gradients of 18O-containing ions implying a homogeneous oxidation in the bulk; the exposed surface however always showed significantly higher signals indicating that the outermost surfaces were more oxidised than the bulk.
4. THERMAL METHODS 4.1 Differential scanning calorimetry (see also Section 2.1) The heat flow into (endothermic) or out (exothermic) of a sample as a function of temperature and time is measured using the technique of DSC. In particular, it is used to study and determine the temperature of thermal transitions. For polymers, these include Tg, the glass transition temperature, Tc, the (exothermic) temperature of crystallisation for polymers that can crystallise, and Tm, the (endothermic) melting temperature. A DSC measurement requires only a small amount of sample; 2–20 mg of a film, powder, fibre or liquid samples can be analysed in a DSC pan. DSC can yield both qualitative and quantitative information, and is a relatively fast technique, with typical heating rates being about 101C min1. It is routinely used to determine oxidation-induction time, see Section 2.1, which can be a useful parameter in assessing the thermal stability of a series of materials [103]. As a relatively recent example of the application of DSC, Blom et al. [104] reported on the use of DSC and impact testing to investigate deterioration of impact properties during polymer processing of a commercial acrylonitrile/ polybutadiene/styrene (ABS) graft copolymer. Loss of polymer performance can occur in such as the injection moulding process when an equipment shutdown happens, and molten polymer is trapped in the barrel of a moulding machine. Of particular concern was the oxidation of the polybutadiene (impact modifier) phase, which because of residual double bonds is susceptible to oxidation. Samples were examined that had been held for pre-determined lengths of time within the halted injection moulded machine. In these samples, increase in the Tg
Polymer Degradation and Oxidation: An Introduction
437
of the rubber (polybutadiene) phase, occurring near 581C, correlated with loss of impact strength. (The Tg of the styrene-acrylonitrile phase occurred at 112.21C.) Increasing polymer degradation was also demonstrated by determining the oxidative onset temperature from a series of DSC traces. In ‘conventional’ DSC, the difference in heat flow is measured between the sample and an inert reference as both are subjected to a linear change in temperature; it can also be used to determine heat capacity by subjecting in two experiments two identical samples of the same mass to two different linear heating rates. In modulated DSC (MDSC) both heat flow and heat capacity may be measured in a single experiment. This is achieved in modulated DSC by superimposing a modulated heating rate onto a linear heating rate. Richaud et al. [105] used a combination of modulated DSC, chemical titration (iodometric method, see above) and mid-infrared spectroscopy to investigate the kinetics of hydroperoxide build-up in the thermal oxidation of isotactic PP from which stabilisers had been extracted, and verify the applicability of their kinetic model, which was derived from a classical branched radical chain scheme (see reference for full details), in which initiation results from POOH (P, polymer) decomposition. In an earlier related publication, [16], these workers had used a combination of MDSC, mid-infrared spectroscopy, iodometric titration and SO2 treatment to monitor oxidation in unstabilised films and stabilised fibres of PP, which were thermally oxidised at 801C under high oxygen (5.0 MPa) pressure. An aim of this work was to investigate the feasibility of using MDSC as an alternative for POOH titration to other methods of detecting hydroperoxides in PP, such as colorimetric methods (see above), which require that the polymer be sufficiently swelled by the solvent. As a small example from this work Figure 37 is shown in which two DSC thermograms are compared. These thermograms, which represent nonreversing parts of heat flow are for oxidised samples before and after SO2 treatment; the effect of SO2 reaction is clearly evident; SO2 scavenges POOH, converting them into sulfates. For the oxidised sample prior to SO2 treatment,
Non Rev Heat Flow (mW)
6 5 4
before treatment after treatment
3 2 1 0 0
50
100 150 200 Temperature (°C)
250
300
Figure 37 MDSC thermograms for non-reversing part of heat flow for oxidised PP samples before and after SO2 treatment. Reprinted from Richaud et al. [16]. Copyright 2006, with permission of Elsevier.
438
John M. Chalmers and Robert J. Meier
a wide exotherm extending from about 901C to about 2001C is seen superimposed on a sharp (derivative-like) component at about 1501C. No broad exotherm is observed in the SO2-treated sample. (It is beyond the scope of this chapter to explain the differences between non-reversing and reversing parts of a DSC thermogram and the derivative band-shape observed in Figure 37, these may be found in Ref. [16]. The purpose here of including Figure 37 was to both illustrate an application of MDSC and once more emphasise the use and importance of multi-techniques/methods in an investigation of polymer degradation).
4.2 Differential photocalorimetry Differential photocalorimetry (DPC) is included here since the instrument used is essentially an adaptation of DSC instrumentation. The photocalorimeter comprises a DSC instrument with a UV/visible source mounted on top, such that light of appropriate wavelength or wavelength region from the source is focused onto the measuring head (both reference and sample pans). The most frequent use of DPC is in the study of polymer cure reactions, but it may also be used to follow such as UV degradation. DPC was used to measure the OIT for formulated isotactic PP samples [106]. Series of samples with and without stabilisers (Irganox 1010s (thermal) and Chimassorb 944s (light)) were analysed by DPC. The samples were examined at an isothermal temperature of 1701C; the OIT values for each sample was determined both without exposure and with exposure to the UV light, which was 2671 W/m2 between 250 and 400 nm. A significant drop in OIT value was noted for all the formulations when exposed to UV light, and the difference in values were related to the stabiliser recipes, which were rationalised by an antagonistic rather than synergistic effect occurring between the light and thermal stabilisers. Another series of similarly formulated samples prepared as films were artificially aged at 340 nm (0.35 W/m2) in a Weather-Ometer according to standard ASTM International (formerly American Society for Testing and Materials) guidelines, and these were studied by optical microscopy for the time of appearance of initial cracks. This was related to the concentration of the light stabiliser, which was reasonable since in the artificially ageing experiment the main environmental agent was UV light, not temperature, since the aging was conducted at 631C. Hence, from this study, no reasonable correlation could be obtained between OIT values by DPC and appearance of cracks in artificially aged samples.
4.3 Thermogravimetric analysis TGA analysis is an instrumental technique that can be used to measure the change in weight (loss or gain) of a polymer as a function of temperature and/or time. Since weight loss curves may look similar, the derivative weight loss curve is often interrogated, since this more clearly defines the point at which weight change is most apparent. TGA is commonly employed in studies of polymer and plastics degradation. Typically a TGA analysis requires 10–25 mg of a sample.
Polymer Degradation and Oxidation: An Introduction
439
TGA was the primary investigation tool in a study of the degradation behaviour of a commercial poly(oxymethylene) (POM) and a commercial POM-copolymer that had been copolymerised with a stabilising comonomer to reduce degradation sensitivity [107]. The study focused on the influence of processing, thermal ageing and UV irradiation. Processed and re-processed samples were compared; the re-processing was done by sequential injection moulding, milling and re-moulding up to six times; accelerated ageing of samples was achieved by thermally ageing in an oven at 1401C for up to 56 days, or in a UV-irradiation test that simulated the standard climate conditions for indoor irradiation in middle Europe. Visibly the oven-aged samples appeared discoloured with surface cracks; the UV-irradiated samples were totally chalked in appearance with some surface cracks. For the TGA examinations, typically 10 mg was analysed from samples taken from the surfaces of the specimens, since these represented the most damaged areas. In the TGA measurements the samples were heated at a rate of 10 K min1 in either an air or nitrogen atmosphere. Air was used instead of oxygen to avoid rapid decomposition and occurrence of self-ignition reactions; also, ceramic TGA sample pans were used, to avoid catalytically accelerated decomposition caused when Pt pans were used. In addition to preparing samples from ‘as supplied’ material, in order to study the mechanism of degradation of the polymer chain, a sample of the POM homopolymer was ‘purified’ to remove stabilisers and other additives. The TGA investigation was complemented also by studies using TGA-MS, to identify the off-gases, and gel permeation chromatography (GPC), to monitor molecular weight distribution changes. Each TGA measurement used represented the average of several, up to 10, TGA measurements. An onset temperature of degradation, defined as a mass loss of 3% of the initial sample mass, was determined. Figure 38 shows one of the TGA spectra recorded from this study [107]. There is only space here to summarise a few of the conclusions that the authors made from this detailed study, these are: TGA indicated that the initiation mechanism of degradation of POM was by random scission of the main chain. (Formaldehyde observed in the TGA-MS measurements is a direct consequence of random scission.) GPC indicated that multiple processing does not influence molecular weight distribution. Depression of the onset temperature (TGA) is attributable to a continuous consumption of stabiliser. TGA-MS results indicate that in the homopolymer, stabiliser consumption occurs during re-processing and oven storage. In the POM homopolymer with stable chain ends, during accelerated ageing, degradation initiation takes place in the amorphous regions, which degrade more rapidly. This was attributed to a decrease in the onset of degradation TGA temperature in the processed samples due to continuous stabiliser consumption and pre-damage of chains in the amorphous regions. For the copolymers, the stabiliser is less affected during accelerated ageing due to the presence of the comonomer units.
440
John M. Chalmers and Robert J. Meier
N2
100 Homopolymer Copolymer
80
DTG (%/min)
TG (%)
60 60
40
20
40 20 0 0
100
0
200
300
400
500
Temperature (°C) 0
100
200 300 Temperature (°C)
400
500
Figure 38 TGA results determined from a POM homopolymer and copolymer sample in a nitrogen atmosphere. The degradation kinetics differs because of their different structures. The derivative DTG curves shown in the inset represent the degradation rates. Reprinted from Archodoulaki et al. [107]. Copyright 2004, with permission from Elsevier.
Recently, these researchers, again using a combination of TGA and TGA-MS, published further studies on the thermo-oxidative ageing of POM, including determining various activation energies [108]. Figure 39 compares two sets of TGA thermograms recorded from UV aged samples of (a) an EVA copolymer containing 13% VA and (b) an EVA copolymer containing 13% VA and 1% carbon black [109]. Also shown (c) is the variation of the activation energies with UV ageing time for these two samples derived from their derivative TGA curves (see reference for details). These data formed part of a complementary study involving mid-infrared spectroscopy, gelation (sol-gel) analysis and TGA to compare the effect of carbon black on the UV ageing characteristics of EVA. The TGA curves in Figures 39 (a) and (b) all show typical step degradation profiles, the first due to loss of acetic acid, the second involving mainly chain scission. These sets of TGA curves show that in both cases the degradation steps are shifted to lower temperatures with UV ageing, and the carbon black has little effect on the degradation process (this in contrary to that for thermal degradation). Little variation is also seen in the activation energies shown in Figure 39(c). In this study, isothermal TGA studies were also undertaken in a nitrogen atmosphere at 3501C and an oxygen atmosphere at 1951C. The first was used to establish the percentage of volatiles evolved, which increased with the UV-ageing history of the samples, but was
Polymer Degradation and Oxidation: An Introduction
441
100 0 80 Weight (%)
48 96
116 140
60
250 400
40 20 0
200
250
300 350
450 500
400
550 600
Temperature (°C) (a)
100
0 140 250
Weight (%)
80
48 96
400
60 40 20 0 200
250
300
350 400 450 Temperature (°C) (b)
500
550
600
Degradation Activation Energy (kJ/mol)
500 EVA 400
EVA/CB
300 200 100 0 0
50 100 150 200 250 300 350 400 450 UV Irradiation Time (hour) (c)
Figure 39 (a) Thermograms of UV aged EVA copolymer in a nitrogen atmosphere; the number against each curve indicates the UV ageing time in hours. (b) Thermograms of UV aged EVA copolymer containing 1% carbon black; the number against each curve indicates the UV ageing time in hours. (c) Variation in degradation activation energies with UV ageing time for EVA copolymer and EVA copolymer containing 1% carbon black (EVA/CB). Reproduced from permission C - opurog˘lu and -S en [109]. Copyright 2005, John Wiley & Sons Limited, permission.
442
John M. Chalmers and Robert J. Meier
very similar for both sets of samples. In the isothermal TGA/oxygen atmosphere experiments, the time to reach specific mass losses was determined and though different, overall the measurements undertaken with all the three analytical tools (mid-infrared, TGA and gelation) showed carbon black to be an ineffective stabiliser of EVA at moderate temperatures. In another recent study, TGA, pyrolyis-MS and mid-infrared spectroscopy were the complementary tools used in an investigation of the thermal-oxidation products and kinetics of high-density polyethylene composites containing a range of different inorganic fillers [110]. Relative carbonyl indexes were determined using mid-infrared spectroscopy for samples that had been oven aged at different temperatures over different periods of time. Pyrolysis-MS was used to compare the volatile components evolved before and after aging. TGA experiments were conducted in an air atmosphere. The TGA and oven test results were however not consistent, since TGA measures thermal decomposition, while the latter, in this case, thermal oxidation.
5. CHROMATOGRAPHIC ANALYSIS 5.1 Gas chromatography GC may be used to separate the volatiles evolving from a polymer undergoing degradation in order to make more effective their identification by a spectroscopic detection technique (see elsewhere in this chapter).
5.1.1 Inverse gas chromatography Inverse gas chromatography (IGC) has found direct applications in the study of the degradation of polymers. IGC is so-named because it is essentially the reverse of conventional GC. In GC the volatile species injected into the column are separated according inter alia the column packing properties and then identified according to their elution time; IGC aids in characterising the properties of the solid compacted into the column. In IGC, the polymer sample (powder, fibre, film, etc.), whose properties are ‘unknown’ forms the packing inside the GC column. Various molecular probes (gases) may then be injected into the column at particular flow rates, and the time taken for them to elute through the column detected. This allows one to interrogate the properties of the polymer sample. IGC was used recently, complemented by mid-infrared spectroscopy, to study the surface thermal oxidation behaviour of a PP powder [111]. PP powder that passed through standard #20 sieve but was retained on a standard #40 sieve was packed inside a pre-cleaned 1 m long copper GC column. IGC experiments were conducted at various temperatures using probe gases of methane, pentane, hexane, heptane and pentene. Adsorption of the n-alkanes was used to calculate the surface free energy from a plot of the free energy of adsorption as a function of carbon number (see, e.g., Figure 40(a)); the acidic nature of the surface was determined from a comparison of the free energy of adsorption between pentane
443
Polymer Degradation and Oxidation: An Introduction
(b)
-65500 -66300 -67300
y = -2503.1x - 51992 R2 = 0.9998
-68300 -69300 -70300
4
4.5
5
6 5.5 6.5 Carbon Number
7
7.5
Free Energy of Adsorption (J/mole)
Free Energy of Adsorption (J/mole)
(a) -64300
Analysis of the Acidic Character of the Surface -64480 -64500 -64520 -64540 -64560 -64580 -64600 4.99
5
5.01 5.02 Carbon Number
5.03
Figure 40 (a) Plot of free energy of adsorption of n-alkane probes vs carbon number: 1101C, 91.5 h oxidation regime. (b) Analysis of surface polarity by zooming in on the carbon number range 4.99–5.03 and observing the difference between the free energy of adsorption of pentane and pentene; pentene is represented by the black square (see Ref. [111] for full details). Reprinted from Calhoun et al. [111]. Copyright 2006, with permission from Elsevier.
and pentene (see Figure 40(b)). Comparisons between the IGC measurements and mid-infrared spectral data showed that an increase in surface energy is detected using IGC before noticeable carbonyl species growth is observed using midinfrared spectroscopy.
5.2 Liquid chromatography Liquid chromatography (LC) encompasses several techniques, which includes HPLC and SEC (sometimes referred to as GPC). Many variants of and developments from these techniques exist, and are used in the study and analysis of polymer degradation/oxidation. As discussed earlier, SEC is often coupled with MALDI-ToF-MS to facilitate the identification of the products of polymer degradation. SEC has also been coupled with mid-infrared detection and similarly used for studies of polymer degradation. SEC/GPC is discussed further below. In LC under critical conditions (LC-CC), the molar mass of the polymer component does not contribute to component separation; separation is influenced by the type and number of functional groups [112]. Therefore for a constant composition homopolymer, the separation will depend solely on endgroups, and as a consequence LC-CC can be useful to study such as the formation of new end-groups resulting from, for example, hydrolytic degradation [112]. LC-CC is based on the controlled coupling of enthalpic and entropic separation mechanisms; in entropy driven HPLC (SEC) the retention volumes of macromolecules decrease with molar mass, whereas they increase with entropydominated HPLC systems. In LC-CC, the two effects compensate allowing macromolecules with different molar masses to elute at the same retention volume [113]. A two-dimensional LC (2D-LC) separation is achieved by utilising
444
John M. Chalmers and Robert J. Meier
two columns linked in sequence; the more divergent these two columns are, the greater the separation potential. In a study of the hydrolytic degradation of poly(bisphenol-A-carbonate) by Coulier et al. [112], a wide range of LC techniques was used. They were: SEC, LC-CC, 2D-LC and coupled LC/MALDI-ToF-MS, SEC/MALDI-ToF-MS and LC/mid-IR. The latter two approaches used a semi-on-line approach, in which a commercial deposition interface was employed; fractions eluting from the separation are deposited onto an appropriate substrate for subsequent analysis by a spectroscopic technique. The material used in the study was a commercially available polycarbonate (PC) containing a small amount of process stabiliser, except for the 2D-LC measurements for which the same PC but with a different stabiliser recipe was used. Following hydrolytic degradation at different oven temperatures (50–1001C) in moist air (ca. 50% v/v water) for different times up to 100 days, the polymer samples were dissolved in chloroform (ca. 10 mg ml1) before analysis. Under the degradation conditions employed: SEC, using UV detection at 256 nm, showed that the molecular mass decreased significantly; LC-CC chromatograms featured an additional peak in the degraded samples that increased with increasing degradation time, and could be attributed to different functionality as a consequence of hydrolytic degradation; LC-CC/mid-IR indicated that the PC associated with the additional peak could be explained by the formation of –OH groups; LC-CC/MALDI-ToF-MS showed that the additional peak observed in the LC-CC chromatogram was PC with one t-butyl end-group and one OH end group; no evidence for other end-groups was found; SEC/MALDI-ToF-MS was used to investigate the PC microstructure before degradation, from which various mass distributions were identified as either PC with two t-butyl end-groups or cyclic oligomers; SEC/MALDI-ToF-MS of the degraded sample confirmed the appearance after degradation of PC containing one t-butyl and one OH end group, and disappearance of cyclic oligomers; 2D-LC (LC-CC/SEC) was employed in order to obtain molecular mass information on the two peaks separated by LC-CC, one due to PC and the additional peak arising from hydrolytically degraded PC. Although the above is a highly simplified summary of the detailed analyses undertaken and the inter-relationships found between these, it emphasises the roles of the complementary and confirmatory techniques. One conclusion from the researchers was that 2D-LC was the most promising technique to detect PC degradation at an early stage.
5.2.1 Size exclusion chromatography/gel permeation chromatography As discussed in the chapter in this book by Wiegand and Ko¨hler (Chapter 6), polymers are polydisperse, that is, they do not have a unique molecular weight but are composed of a mixture of different chain lengths and sizes from
Polymer Degradation and Oxidation: An Introduction
445
sometimes near monomeric to perhaps several thousand repeat units. There is a distribution of molecular weight. Although we often talk of the molecular weight of a polymer it is more appropriated to consider it in combination with the molecular weight distribution (MWD). Chain scission accompanied by termination or recombination will immediately alter the MWD. The most popular and convenient way of following this is by GPC, also called size exclusion chromatography (SEC). Polymer degradation can be and is extensively studied by conventional or multi-detector (most usually Triple Detection) GPC. Simple GPC separates molecules according to their molecular size in solution. A concentration detector (usually refractive index but sometimes UV or IR) continuously detects the amount of polymer that elutes from the separation column. The separation process is calibrated with standard reference materials of known molecular weight and with a narrow MWD such that the peak elution volume can act as a marker for that particular molecular weight. This technique is known as ‘Conventional GPC’ or ‘Conventional Calibration GPC’. It is very powerful when used in the comparative mode and among other things the graphical output will give a generally understood appreciation of polymer degradation. However, it is less easy to actually quantify the extent of degradation because Conventional GPC is a secondary technique; it uses an equivalent scale of measurement. GPC separates according to molecular size not molecular weight; branched molecules occupy a smaller space in solution than a straight chain molecule of the same molecular weight. The calibration process is based on linear standards of a particular polymer type (polystyrene, for example). So where branching is present the molecular weight is underestimated. And the polymer type is rarely the same as that of the standards. Every polymer has a unique relationship between its molecular size and molecular weight. The solution to the quantitation issue is to use a multi-detector GPC. The most useful combination is to use a triple detector array comprising refractive index, light scattering and viscometric elements. Although the signals are complex it is reasonably easy to resolve them. Simplistically the refractometer will give rise to the concentration term, light scattering the molecular weight, and the viscometer the molecular size components, respectively. With these data the instrument software package can easily generate the actual molecular weight distribution and the molecular size distribution. This is free from any assumptions or equivalences. From this basic information other relationships can be derived such as the rate of change of molecular size with molecular weight along with the branching index and estimates of whether it is long- or short-chain branching. It is then possible to work out what sort of degradation has taken place and indeed the extent to which it has taken place. Tetra Detection GPC makes further refinements with the addition of a UV or IR detector. Of course there must be a suitable chromophore in the polymer chain and a corresponding spectral window in the solvent through which to view it. It is then possible to generate the composition distribution to complement the
446
John M. Chalmers and Robert J. Meier
Polymer Degradation and Oxidation: An Introduction
447
MWD. By tetra-detection GPC there is however a danger of information overload. It is usually more comprehensible if the Triple Detection calculations are repeated but with data from the spectrometer replacing that of the refractometer. Since all the detectors are on-line all the time it is easy for software to mix and match as required. Figure 30 in the mass spectrometry section above showed an example of SEC traces comparing an unoxidised and oxidised PC samples [84]. White and co-workers have used GPC as the primary tool in investigations of the photodegradation of various aliphatic hydrocarbon homopolymers and copolymers [114–116]. Tensile test bars were exposed to UV radiation at 301C for different times; some bars were exposed while under applied uniaxial tensile stress. Samples for GPC analysis were prepared from these by milling material from the bars using a single point cutter with fly cutting action. From the GPC data, using a computer-aided analysis procedure (see Refs. [114] and [115] for details) the researchers depth profiled the formation of chain scission and cross-link concentrations through the tensile bars as functions of time and UV exposure. Figure 41 shows the GPC experimental molecular weight distributions (MWDs) for PP samples. The results obtained indicated that an applied tensile stress accelerated polymer chain scission near the surface [114].
6. CLOSING REMARKS As is evident in the many examples selected in this chapter to illustrate the molecular characterisation and analysis of polymer degradation and oxidation processes, almost, without exception, each study or investigation cited has involved use of more than one analytical method or characterisation technique, often many more than two. This clearly emphasises the importance of using a multi-technique approach to provide supportive, complementary and confirmatory information, since each technique or method yields a different aspect of the degradation/oxidation process in polymers. As stated in the Introduction to this chapter (Section 1), the next two chapters deal more specifically with CL and electron spin resonance spectroscopy as applied to studies of polymer degradation, each of which was also referred to in some of the multi-technique studies cited within this chapter.
Figure 41 (a) GPC experimental MWDs for PP samples: the virgin PP sample, and samples extracted from near the exposed face, near the back face, and from the interior from an unstressed tensile bar exposed to UV radiation for 4 weeks. Wn (log M) describes the normalised fraction of molecules with mass M. Concentrations (mol/kg) of (b) chain scissions (number of bonds scissioned) and (c) cross-links (number of bonds cross-linked) in PP samples after 4 weeks UV exposure. (d) Ratio of scission/cross-link concentrations vs depth for PP bars exposed for 4 weeks to UV radiation: one bar was unstressed and one bar was held in uniaxial tension. Reprinted from Shyichuk et al. [114]. Copyright 2001, permission from Elsevier.
448
John M. Chalmers and Robert J. Meier
ACKNOWLEDGEMENT The authors are grateful to Alan Titterton (Hutton Rudby, U.K.) for significant advice on the GPC/SEC section content.
REFERENCES 1 J. Scheirs, Composition and Failure Analysis of Polymers: A Practical Approach, Wiley, Chichester, 2000. 2 ISO 11357-6 Plastics – Differential scanning calorimetry (DSC)– Part 6: Determination of oxidation induction time, International Organization for Standardization, Geneva, Switzerland. 3 ASTM D3895-07 Standard Test Method for Oxidative-Induction Time of Polyolefins by Differential Scanning Calorimetry, Book of Standards Vol. 08.02, ASTM International (formerly known as American Society for Testing and Materials), West Conshohocken, PA, USA. 4 S.M. Marcus and R.L. Baine, Estimation of bias in the oxidative induction time measurement by pressure DSC, Application note: TA-228, TA Instruments, Inc., New Castle, DE, USA. 5 M. Schmid, A. Ritter and S. Affolter, J. Therm. Anal. Calorim., 83 (2006) 367. 6 A.B. Lugao, E.C.L. Cardoso, B. Hutzler, L.D.B. Machado and R.N. Conceic- a˜o, Rad. Phys. Chem., 63 (2002) 489. 7 L. Woo, S.Y. Ding, M.T.K. Ling and S.P. Westphal, J. Therm. Anal. Chem., 49 (1997) 131. 8 V.-M. Archodoulaki, S. Lu¨ftl and S. Seidler, Polym. Test., 25 (2006) 83. 9 P.K. Fearon, S.W. Bigger and N.C. Billingham, J. Therm. Anal. Calorim., 76 (2004) 75. 10 T. Zaharescu, Mat. Res. Innovat., 5 (2001) 35. 11 J. Scheirs, S.W. Bigger and N.C. Billingham, Polym. Test., 14 (1995) 211. 12 P. Gijsman and M. Hamskog, Polym. Degrad. Stab., 91 (2006) 423. 13 T. Corrales, F. Catalina, C. Peinado, N.S. Allen and E. Fontan, J. Photochem. Photobiol A, Chem, 147 (2002) 213. 14 G. Botelho, A. Queiro´s, A. Machado, P. Frangiosa and J. Ferreira, Polym. Degrad. Stab., 86 (2004) 493. 15 E.M. Hoa`ng, N.S. Allen, C.M. Liauw, E. Fonta´n and P. Lafuente, Polym. Degrad. Stab., 91 (2006) 1363. 16 E. Richaud, F. Farcas, B. Fayolle, L. Audouin and J. Verdu, Polym. Test., 25 (2006) 829. 17 M. Salvalaggio, R. Bagatin, M. Fornaroli, S. Fanutti, S. Palmery and E. Battistel, Polym. Degrad. Stab., 91 (2006) 2775. 18 S. Luzuriaga, J. Kova´rˇova´ and I. Fortelny´, Polym. Degrad. Stab., 91 (2006) 1226. 19 S. Aslanzadeh and M.H. Kish, Polym. Degrad. Stab., 90 (2005) 461. 20 ASTM D1238-04c Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer, Book of Standards Vol. 08.011, ASTM International (formerly known as American Society for Testing and Materials), West Conshohocken, PA, USA. 21 ISO 11357:2005 Plastics – Determination of the melt mass-flow rate (MFR) and the melt-volume flow rate (MVR) of thermoplastics. International Organization for Standardization, Geneva, Switzerland. 22 M. Flanagan, Mechanical and rheological testing. In: B.J. Hunt and M.I. James (Eds.), Polymer Characterisation, Blackie Academic and Professional, Glasgow, 1993, pp. 261–296: Chapter 9. 23 J.P. Luongo, J. Polym. Sci., 42 (1960) 139. 24 D.L. Wood and J.P. Luongo, Modern Plastics, March, 132 (1961). 25 F.J. Boerio and S. Wirasate, Measurements of the chemical characteristics of polymers and rubbers by vibrational spectroscopy. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007, pp. 113–141. 26 J.M. Chalmers and N.J. Everall, Qualitative and quantitative analysis of plastics, polymers and rubbers by vibrational spectroscopy. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007, pp. 1–67. 27 B.J. Holland and J.N. Hay, Polymer, 42 (2001) 4825.
Polymer Degradation and Oxidation: An Introduction
28 29 30 31 32 33 34
35 36 37 38
39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57
58 59 60 61 62 63 64 65 66
449
B.J. Holland and J.N. Hay, Polym. Int., 49 (2000) 943. C.H. Do, E.M. Pearce and B.J. Bulkin, J. Polym. Sci. Part A, Polym. Chem., 25 (1987) 2409. M.M. Coleman and G.T. Sivy, Carbon, 19 (1981) 123. G.T. Sivy and M.M. Coleman, Carbon, 19 (1981) 127. M.M. Coleman and G.T. Sivy, Carbon, 19 (1981) 133. G.T. Sivy and M.M. Coleman, Carbon, 19 (1981) 137. J.-L. Gardette, Infrared spectroscopy in the study of the weathering and degradation of polymers. In: J.M. Chalmers and P.R. Griffiths (Eds.), Handbook of Vibrational Spectroscopy, , Wiley, Chichester, 2002, Vol. 4, pp. 2514–2522. R.P. Singh, R. Mani, S. Sivaram, J. Lacoste and J. Lemaire, Polym. Int., 32 (1993) 189. V. Ollier-Dureault and B. Gosse, J. Appl. Polym. Sci., 70 (1998) 1221. A. Rivaton, Polym. Degrad. Stab., 49 (1995) 163. T.J. Henman, Characterisation of oxidised polyolefines by reaction with sulphur dioxide. In: N. Grassie (Ed.), Developments in Polymer Degradation-6, Elsevier Applied Science, Barking, 1985, pp. 107–145. N. Sellin and J.S.C. Campos, Mater. Res., 6 (2003) 163. A. Marek, L. Kapra´lkova´, P. Schmidt, J. Pfleger, J. Humlı´cˇek, J. Pospı´sˇil and J. Pilarˇ, Polym Degrad. Stab., 91 (2006) 444. K.V. Wilson, B.L. Smith, J.M. Macdonald, J.R. Schoonover, J.M. Castro, M.E. Smith, M.E. Cournoyer, R. Marx and W.P. Steckle, Polym. Degrad. Stab., 84 (2004) 439. A. Jansson, K. Mo¨ller and T. Hjertberg, Polym. Degrad. Stab., 84 (2004) 227. S.A.S. Alariqi, A.P. Kumar, B.S.M. Rao and R.P. Singh, Polym. Degrad. Stab., 91 (2006) 1105. D. Hadad, S. Geresh and A. Sivan, J. Appl. Micribiol., 98 (2005) 1093. C. Jin, P.A. Christensen, T.A. Egerton, E.J. Lawson and J.R. White, Polym. Degrad. Stab., 91 (2006) 1086. J.-N. Leichtnam, D. Schwartz and R. Gadiou, J. Anal. Appl. Pyrolysis, 55 (2000) 255. A. Gonzalez, L. Irusta, M.J. Ferna´ndez-Berridi, M. Iriarte and J.J. Iruin, Polym. Degrad. Stab., 87 (2005) 347. M.B. Maurin, L.W. Dittert and A.W. Hussain, Thermochim. Acta, 186 (1991) 97. C.A. Wilkie, Polym. Degrad. Stab., 66 (1999) 301. D.L. Gerrard and W.F. Maddams, Macromolecules, 8 (1975) 54. N.J. Everall, Industrial applications of Raman spectroscopy. In: D.L. Andrews and A.A. Demidov (Eds.), An Introduction to Laser Spectroscopy, Plenum Press, New York, 1995, pp. 115–131. B.J. Kip, S.M. van Aken, R.J. Meier, K.P.J. Williams and D.L. Gerrard, Macromolecules, 25 (1992) 4290. M. Trchova´, P. Mate˘jka, J. Brodinova´, A. Kalendova´, J. Prokesˇ and J. Stejskal, Polym. Degrad. Stab., 91 (2006) 114. M. Dubois, A. Naji, J.P. Buisson, B. Humbert, E. Grivei and D. Billaud, Carbon, 38 (2000) 1411. T.H. Ko, W.-S. Kuo and Y.-H. Chang, J. Appl. Polym. Sci., 81 (2001) 1084. J. Ma, L. Shi, Y. Shi, S. Luo and J. Xu, J. Appl. Polym. Sci., 85 (2002) 1077. P.M. Fredericks, Depth profiling of polymers by vibrational spectroscopy. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007, pp. 179–200. A. Sze´p, P. Anna, I. Csontos, Gy. Marosi, Sz. Matko´ and Gy. Bertalan, Polym. Degrad. Stab., 85 (2004) 1023. J.S. Kim, P.K.H. Ho, C.E. Murphy, A.J.A.B. Seeley, I. Grizzi, J.H. Burroughes and R.H. Friend, Chem. Phys. Lett., 386 (2007) 2. P. Taddei, R. Simoni and G. Fini, J. Mol. Struct., 565-566 (2001) 317. M. Reggiani, P. Taddei, A. Tinti and C. Fagnano, Biopolymers, 74 (2004) 146. R. Benavides, M. Edge, N.S. Allen and M.M. Tellez, Polym. Bull., 42 (1999) 273. R. Benavides, M. Edge, N.S. Allen, M. Shah and M.M. Tellez, Polym Degrad. Stab., 48 (1995) 377. R. Benavides, M. Edge, N.S. Allen and M. Shah, Polym. Degrad. Stab., 57 (1997) 25. R. Benavides, M. Edge and N.S. Allen, Polym. Degrad. Stab., 44 (1994) 375. A. Rivaton, B. Mailhot, J. Soulestin, H. Varghese and J.L. Gardette, Polym. Degrad. Stab., 75 (2002) 17.
450
67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116
John M. Chalmers and Robert J. Meier
N.S. Allen, M. Edge, M. Rodriguez, C.M. Liauw and E. Fontan, Polym. Degrad. Stab., 68 (2000) 363. C. Peinado, N.S. Allen, E.F. Salvador, T. Corrales and F. Catalina, Polym. Degrad. Stab., 77 (2002) 523. C. Puglisi, L. Sturiale and G. Montaudo, Macromolecules, 32 (1999) 2194. K.L. Busch, Mass Spectrom., 17(6S) (2002) S26–S34. T. Wampler, Polymer Degradation Mechanisms Encountered in Pyrolysis-GC/MS, Perkin Elmer Life and Analytical Sciences, Shelton, CT, USA, Field Application Report. G. Montaudo, C. Puglisi, R. Rapisardi and F. Samperi, Macromol. Chem. Phys., 195 (1994) 1225. G. Montaudo, C. Puglisi and F. Samperi, J. Polym. Sci. Part A, Polym. Chem., 32 (1994) 1807. T. Uyar, C.C. Rusa, A.E. Tonelli and J. Hacalog˘lu, Polym. Degrad. Stab., 92 (2007) 32. T. Uyar, C.C. Rusa, M.A. Hunt, E. Aslan, J. Hacalog˘lu and A.E. Tonelli, Polymer, 46 (2005) 4762. E. Aslan, J. Hacalog˘lu and L. Toppare, Polym. Degrad. Stab., 92 (2007) 822. C. Puglisi, F. Samperi, S. Carroccio and G. Montaudo, Macromolecules, 32 (1999) 8821. S. Carroccio, C. Puglisi and G. Montaudo, Macromolecules, 35 (2002) 4297. S. Carroccio, C. Puglisi and G. Montaudo, Macromolecules, 36 (2003) 7499. S. Carroccio, C. Puglisi and G. Montaudo, Macromolecules, 37 (2004) 6037. S. Carroccio, P. Rizzarelli, C. Puglisi and G. Montaudo, Macromolecules, 37 (2004) 6576. S. Carroccio, C. Puglisi and G. Montaudo, Macromolecules, 38 (2005) 6849. S. Carroccio, C. Puglisi and G. Montaudo, Macromolecules, 38 (2005) 6863. G. Montaudo, S. Carroccio and C. Puglisis, Polym. Degrad. Stab., 77 (2002) 137. J.L. Koenig, Spectroscopy of Polymers, 2nd edn, Elsevier Science, Inc., New York, 1999. D.J. Harris, R.A. Assink and K.T. Gillen, J. Appl. Polym. Sci., 90 (2003) 2578. R.S. Maxwell, D. Chambers, B. Balazs, R. Cohenour and W. Sung, Polym. Degrad. Stab., 82 (2003) 193. C.M. Dick, J.L. Liggat and C.E. Snape, Polym. Degrad. Stab., 74 (2001) 397. S.C. Chinn, T.S. Wilson and R.S. Wilson, Polym. Degrad. Stab., 91 (2006) 541. A. Labouriau, J.D. Cox, J.R. Schoonover, B.M. Patterson, G.J. Havrilla, T. Stephens and D. Taylor, Polym. Degrad. Stab., 92 (2007) 414. A.P. Pijpers and R.J. Meier, Chem. Soc. Rev., 28 (1999) 233. S. Storp and M. Bock, Farbe & Lack, 91 (1985) 914. S. Scierka, A. Forster and W. Kosik, Proceedings of the 81st Annual Meeting Technical Program of the FSCT (Federation of Societies for Coatings Technology), 13–14 November, Philadelphia, 2003. J. Wang, J. Du, J. Zhu and C.A. Wilkie, Polym. Degrad. Stab., 77 (2002) 249. J. Du, J. Wang, S. Su and C.A. Wilkie, Polym. Degrad. Stab., 83 (2004) 29. J. Du, J. Zhu, C.A. Wilkie and J. Wang, Polym. Degrad. Stab., 77 (2002) 377. J. Du, D. Wang, C.A. Wilkie and J. Wang, Polym. Degrad. Stab., 79 (2003) 314. D.J. Upadhyay, N.-Y. Cui, C.A. Anderson and N.M.D. Brown, Polym. Degrad. Stab., 87 (2005) 33. N.-Y. Cui, D.J. Upadhyay, C.A. Anderson and N.M.D. Brown, Surf. Coat. Technol., 192 (2005) 94. N.-Y. Cui, D.J. Upadhyay, C.A. Anderson, B.J. Meenan and N.M.D. Brown, Appl. Surf. Sci., 253 (2007) 3865. A.P. Pijpers and R.M. Meier, J. Electr. Spectrosc. Rel. Phenom., 12 (2001) 299. K. Mo¨ller, A. Jansson and P. Sjo¨vall, Polym. Degrad. Stab., 80 (2003) 345. Z. Dobkowski, Polym. Degrad. Stab., 91 (2006) 488. H. Blom, R. Yeh, R. Wojnarowski and M. Ling, J. Therm. Anal. Calorim., 83 (2006) 113. E. Richaud, F. Farcas, B. Fayolle, L. Audouin and J. Verdu, Polym. Degrad. Stab., 92 (2007) 118. J.E. Volponi, L.H.I. Mei and D.S. Rosa, Polym. Test., 23 (2004) 461. V.-M. Archodoulaki, S. Lu¨ftl and S. Seidler, Polym. Degrad. Stab., 86 (2004) 75. S. Lu¨ftl, V.-M. Archodoulaki and S. Seidler, Polym. Degrad. Stab., 91 (2006) 464. M. C - opurog˘lu and M. -S en, Polym. Adv. Technol., 16 (2005) 61. R. Yang, Y. Liu, J. Yu and K. Wang, Polym. Degrad. Stab., 91 (2006) 1651. A.A. Calhoun, P.D. Nicholson and A.B. Barnes, Polym. Degrad. Stab., 91 (2006) 1964. L. Coulier, E.R. Kaal and Th. Hankemeier, Polym. Degrad. Stab., 91 (2006) 271. T. Macko, D. Hunkeler and D. Berek, Macromolecules, 35 (2002) 1797. A.V. Shyichuk, D.Y. Stavychna and J.R. White, Polym. Degrad. Stab., 72 (2001) 279. A.V. Shyichuk and J.R. White, J. Appl. Polym. Sci., 77 (2000) 3015. A.V. Shyichuk, J.R. White, I.H. Craig and I.D. Syrotynska, Polym. Degrad. Stab., 88 (2005) 415.
CHAPT ER
11 The Role of Oxidation in Degradation of Polymers: The Relation of Oxidation to the Light Emission from Oxidized Polymers Jozef Rychly´ and Lyda Matisova´-Rychla´
Contents
1. Introduction, Historical Overview and Terminology Associated with the Degradation and Ageing of Polymers 2. Methodology and Analytical Techniques in Polymer Stability Studies 3. Mechanisms Leading to the Light Emission from Thermally Oxidized Polymers (Chemiluminescence), Similarities and Differences within Respective Groups of Polymers 4. General Classification of Chemiluminescence from Polymers 5. Comparison of Chemiluminescence for Isothermal and Non-Isothermal Conditions with those Obtained by DSC 6. The Effect of Initial Molar Mass on Chemiluminescence Runs 7. The Effect of Temperature on Chemiluminescence Intensity; The Mutual Relation of Isothermal and Non-Isothermal Studies 8. Relaxation Experiments (Jump Changes of Concentration of Oxygen, Temperature and Humidity) and Rate Constants of Respective Elementary Reaction Steps 9. The Effect of Antioxidants and Polymer Stabilizers 10. Isothermal Kinetics of Polymers Oxidation and Its Relation to the Concentration of Oxygen in Surrounding Atmosphere 11. The Effect of Alkaline Additives on Chemiluminescence Runs: A Possible Impact 12. Conclusions and Outline of the Further Perspectives Acknowledgements References
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00411-X
452 461
463 471 476 478 480
482 483 487 490 493 496 496
r 2008 Elsevier B.V. All rights reserved.
451
452
Jozef Rychly´ and Lyda Matisova´-Rychla´
1. INTRODUCTION, HISTORICAL OVERVIEW AND TERMINOLOGY ASSOCIATED WITH THE DEGRADATION AND AGEING OF POLYMERS The oxidation of polymers is accompanied to varying extents by chemiluminescence, the intensity of which is determined by the quality of a polymer, temperature, concentration of oxygen in the surrounding medium, presence of additives and stabilizers and by the initial molar mass of the substrate. The potential of the measurements of the light emission that appears during oxidation has not been explored yet fully, and the method is mostly used in scientific institutions, either as a main technique or complementary to other methods used for the study of oxidative degradation of polymers. This chapter, which is mostly based on personal experience of the authors, will hopefully serve as a concise introduction for those who intend to apply the chemiluminescence technique in their own research. Application of oxidation experiments on both synthetic polymers and polysaccharides examined by chemiluminescence enables one to provide a more reliable mechanism of the light emission during oxidation. An idea has been developed that the strongest light emission comes from hydroperoxidation of b-positions of electron-withdrawing groups on the macromolecular chain such as carbonyls, carboxyls, amido, hydroxyls, etc. Although such hydroperoxides are usually only present in a small fraction in a polymer, there exists a rather close relation between both the concentration of peroxidic groups in the polymer and chemiluminescence signal. It may provide useful information on the extent of polymer stabilization, on initial molar mass and even on the rate constant of polymer degradation. Analytical application of determination of hydroperoxide content in a polymer by measuring chemiluminescence in an inert atmosphere has not yet been fully explored. A complete understanding of all the relationships is still not available and an effort to achieve that represents the challenge for those who want to predict the remaining service life of polymer materials. The term ‘‘degradation of macromolecules’’ concerns the processes that are accompanied by deterioration in polymer properties. Chemical processes related to the worsening polymer properties may lead to both a reduction of average molar mass due to the scission of bonds in the macromolecular chain, or to an increase of the molar mass due to the crosslinking causing the polymer to become insoluble. One particular group of degradation processes is represented by polymer reactions where the average molar mass remains almost unchanged, but the splitting off of some side groups or their modification occurs as, for example, in the case of poly(vinyl chloride) or poly(vinyl alcohol), where HCl or H2O are formed by unzipping of corresponding atoms or groups from the main chain of a macromolecule and unsaturated CQC bonds remain in the polymer backbone. The term ageing of polymers is usually reserved for long-term changes in properties of polymers exposed to weathering conditions. It may involve any of the above processes and include physical processes of polymer recrystallization and denaturation of, for example, protein structure in biopolymer chemistry. The term corrosion, used essentially for the deterioration (ageing) of metal
Role of Oxidation in Degradation of Polymers
453
properties, does not find much support as an equivalent terminology for polymer ageing. The mode of degradation is determined by the character of the first initiating site in the polymer structure. According to the mechanism that brings about the occurrence of this initiating site we differentiate photodegradation (photolysis), thermal degradation (thermolysis), photo-oxidation or thermo-oxidative degradations, which involve the assistance of oxygen, radiolytic and mechanochemical degradation, etc. Polymers may degrade under the effect of ozone, peroxides, acid and alkaline compounds, halogens or other aggressive compounds, under the effect of electric field, plasma and corona discharge, ultrasound, laser radiation, etc. A particular field of polymer degradation is high-temperature degradation leading ultimately to polymer burning and carbonization, which brings about the total destruction of the polymer material. The initiating sites from which the degradation process begins may be in the form of ions, free radicals or excited states of molecules. The facility of their formation in the polymer depends on the average number of weak bonds in the macromolecular structure that are incorporated into the polymer during its synthesis and subsequent storage. They may be related to the impurities or catalysts residues that remain in the polymer from its synthesis. Potential sites of the polymer degradation are head-to-head or tail-to-tail linkages of monomer units in a macromolecular chain in a polymer, which are thermodynamically less stable than head-to-tail linkages and terminal groups, which are usually more reactive than the units in the chain. The head-to-head structural irregularity, however, need not necessarily be the source of lower stability of polymer product. For example, for polystyrene (PS), poly(vinyl cyclohexane) and poly(methyl methacrylate) both types of structural units, that is, head-to-head and head-to-tail show comparable thermal stability [1]. Very undesirable structural irregularities are O–O bonds that may be introduced into the polymer during its storage and/or during the polymerization of monomers not sufficiently deprived from oxygen. The strength of bonds that may form the macromolecular backbone decreases in the sequence CQNWCQCWPQNWNQNWSi–OWC–OWC–CWC–NWC–SiWN–OWO–O (see Table 1). The scission of the macromolecular backbone may take place as the secondary process following the rupture of some bond in the pendant group; the order of the thermal stability of such bonds is as follows: Si–FWO–HWC–FWC–HWSi–ClWC–ClWSi–BrWC–BrWC–SWO–O (Table 1). The average dissociation energy of bonds forming the structure of a macromolecule appears thus to be a first criterion for estimating the thermal stability of a given polymer. The fraction of bonds that reaches the energy equal to dissociation energy D is determined by the Boltzman’s factor expðD=RTÞ
454
Table 1
Jozef Rychly´ and Lyda Matisova´-Rychla´
Dissociation energies of bonds A–B in kJ/mol that may form the polymer structure
A
H
C
N
O
F
Cl
Br
I
S
Si
H C N O F Cl Br I S Si
436
413 348
391 292 160
463 352 222 139
563 441 270 185 153
432 329 200 203 254 243
366 276
299 240
339 259
290 369
219
193 151
250 178 213
541
359
289
Notes: CQC 615 C N 891 N ¼ N 418; C C 812 CQO 716 N N 946; CQN 615 NQO 607 OQO 498.
where T stands for absolute temperature and R for universal gas constant. This may be exemplified as follows: the temperature at which in one mole of C–C bonds at least one is dissociated into radicals is 4861C, while in one mole of O–O bonds it is only 301C. The thermal and thermo-oxidation stability of a given polymer is usually determined by its rate of degradation by following, for example, the loss of the sample mass by thermogravimetry, from the formation of unsaturated, carbonyl, carboxyl, hydroxyl or hydroperoxide groups, or from the formation of carbonaceous residue at higher temperatures in the case of polymers which predominantly crosslink. The most decisive, however, are the remaining mechanical properties. From the temperature dependence of rate constants, the activation energy E and the pre-exponential factor of the degradation are calculated in order to perform an extrapolation of the data rates to another temperature region. A quite useful relation that may be used for an estimate of the activation energy E of degradation is based on a comparison of the dissocation energies D of the newly formed (j) and disappearing (i) bonds so that X X E¼ Di a Dj where a represents an empirical coefficient the value of which varies from 0.5 to 1 depending on the mechanism of the degradation process. Qualitatively, the more stable the degradation products are, the lower is the activation energy of the process and the higher is its rate. Possible pathways of the degradation reaction may be visualized for a linear hydrocarbon chain in which the reaction centre () is formed by the effect of initiation (heat, light, oxygen, shear stress, etc.), see Scheme 1a. A complementary reaction site is denoted as (–). For example, when () is a free radical site, (–) is also a free radical site, if () is a cation, then (–) is an anion, etc. The three stages of the reaction depicted in Scheme 1a, are initiation, propagation and termination, respectively. The dissociation energies of bonds situated in a b-position to the reaction site () are considerably lower than those
Role of Oxidation in Degradation of Polymers
455
initiation
propagation
+
+
+
termination
+
Scheme 1a
Alternatives for the scission of the polymer chain from the primary initiating site. CH3CH2
CH3CHCH2
CH2CH3
CH3
D=348 kJ/mol
D=105 kJ/mol
saturated compound
free radical
Scheme 1b Comparison of the dissociation energy of respective bonds in n-butane and 2-butyl radicals.
corresponding to a saturated compound, and the subsequent fragmentation occurs predominantly there. For the case of is a free radical site, we may compare it on the example above for the C–C bond in butane and 2-butyl radical (Scheme 1b). Such b-fragmentation propagates the reaction site either via the splitting of the main chain and lowering the average molar mass of the polymer or via the splitting off the side groups. The splitting of the main chain may occur statistically or as the unzipping process with formation of an unsaturated lower molar mass compound. A very efficient co-factor to reducing the stability of any polymer is the presence of oxygen, which affects any mode of initiation. It is related with quite a fast introduction of unstable O–O bonds into the polymer structure and
456
Jozef Rychly´ and Lyda Matisova´-Rychla´
Reaction:
No.:
wi
PH
P•
P• + O2
PO2• k3
PO2• + PH k1
POOH
1
k2
2 POOH
PO + PO2•
kf
•
POOH + P• •
kbi
oxygen absorption
•
OH
DSC and any analytical determination of hydroperoxides
•
2 3 4 5
+ PO + H2O
P + products of lower molar mass 6 mechanical tests, thermogravimetry k3′ • PO ( OH) + PH POH(H2O) + P alcoholic groups and water determination 7 k4 • • + P P P P crosslinking 8 k5 • • POOP P + PO2 temporary crosslinking 9 POOP + O2 • • 10 PO2 + PO2 k6 PO
• •
•
PO2
+
k7
InH
POOH + D
k8
P
O + POH + O2 non-radical products
chemiluminescence analysis of inhibitors, induction time
non-radical products
11 12 13
Scheme 2 Bolland–Gee scheme of free radical oxidation of polymer pH. P denotes macromolecular chain, InH is chain-breaking inhibitor, D peroxide decomposer and parameters above arrows are the corresponding rate constants.
development of a free radical mechanism according to Scheme 2, which was proposed by Bolland and Gee [2] for autooxidation of rubber compounds. Free radicals P generated during the initiation process (reaction 1) are, in the presence of oxygen, converted to peroxyl radicals PO2 (reaction 2), and subsequently to hydroperoxides (reaction 3); intermediate hydroperoxides provoke further chain reaction unless stabilizers (InH or D) are used to interrupt it (reactions 12 and 13). Respective reaction of the scheme is completed by the method that monitors it. Thermal decomposition of dialkyl peroxides, diacyl peroxides, hydroperoxides and peracids depending on the structure of the peroxidic compound occurs in a measurable rate usually above 601C. Diacyl peroxides and peracids are considerably less stable than dialkyl peroxides and hydroperoxides. Some traces of metal and metal ions may initiate the decomposition of hydroperoxides even at room temperature. Traces of metal ions are present in almost all polymers and they may affect considerably the polymer oxidation and its subsequent degradation. The sequence of efficiency of metal ions to enhance degradation depends on its valence state and the type of its ligand, but may be postulated as follows: CuWMnWFeWCrWCoWNi This sequence correlates quite well with the reactivity of these ions in the Haber– Weiss cycle of hydroperoxide decomposition. POOH þ Menþ ! PO þMeðnþ1Þþ þ OH Meðnþ1Þþ þ POOH ! PO2 þ Menþ þ Hþ
Role of Oxidation in Degradation of Polymers
457
However, the mechanism for any particular ion may be more complex involving, for example, the reaction of a lower oxidation state of metal ion with peroxyl radicals, etc. Ions of Al, Ti, Zn and V usually reduce the rate of oxidation. The decompositions of hydroperoxides (reactions 4 and 5) that occur as a unior bimolecular process are the most important reactions leading to the oxidative degradation (reactions 4 and 5). The bimolecular reaction (reaction 5) takes place some time after the unimolecular initiation (reaction 4) provided that a sufficiently high concentration of hydroperoxides accumulates. In the case of oxidation in a condensed system of a solid polymer with restricted diffusional mobility of respective segments, where hydroperoxides are spread around the initial initiation site, the predominating mode of initiation of free radical oxidation is bimolecular decomposition of hydroperoxides. Reaction 6 representing b-scission of alkoxyl radicals leading to the reduction of molar mass competes with transfer of a free radical centre to surrounding groups with consequent formation of alcoholic groups (reaction 7), which subsequently loose water and CQC unsaturation appears randomly along the polymer chain. Reactions 8–11 represent the termination of free radical sites, which may have the character of crosslinking (reaction 8) and/or formation of dialkyl peroxides (reactions 9 and 10), which may act as a new initiating species. Reaction 10 is typical for tertiary peroxyl radicals, while reaction 11 for secondary (and may be primary) peroxyl radicals. In the latter case, the disproportionation of peroxyl radicals takes place according to Russell’s scheme where carbonyl groups and oxygen are being formed in excited triplet and singlet states. The conversion of these excited states to the ground state occurs with lower or higher yield as a radiative process (chemiluminescence). The prolongation of the service life of a given polymer in practical utilization has significant practical and commercial impact. The routes of how to achieve a longer service time of a material consist in modifying it by elimination of its weakest structural sites or by mixing a polymer with additives, which protect it by eliminating some of the pathways for generation of active sites of degradation. Such protective additives or ‘‘stabilizers’’ function by absorbing the energy of an initiation process more efficiently than the polymer itself. Once formed, the primary sites of degradation may be deactivated either physically (quenching of excited states) or chemically (inhibition of chemical reaction propagating the oxidation) (see, e.g., reactions 12 and 13 of Scheme 2). The species that are formed from protective compounds should be less reactive than species being formed during degradation of the non-protected polymer. Since the deterioration of polymer properties is related to polymer degradation, the protective additives aimed at the increase of residual service life are called ‘‘antidegradants’’ or ‘‘stabilizers’’. According to the predominating function of such additives we distinguish thermo and photo-oxidation stabilizers, antioxidants, antiozonants, flame retardants, antirads (radiation protectants), biological antioxidants, etc. (see Chapter 3). Mixtures of different additives may have either a synergistic effect, when prolongation of the service life due to the mixture of stabilizers is higher than a simple arithmetic sum of each, or be
458
Jozef Rychly´ and Lyda Matisova´-Rychla´
antagonistic, when the mixture of stabilizers is less efficient than the sum of each of the component. Stabilizing additives for polymers usually scavenge free radicals or hydroperoxides from the system. The effect of such additives is depicted in reactions 12 and 13 of the Scheme 2, which compete with propagation of free radicals according to reactions 3–5. According to the predominance of reactions 12 or 13 we distinguish between chain-breaking antioxidants (InH), which intervene directly with the oxidation cycle by fast reactions with alkyl or peroxyl radicals, and preventive antioxidants (D), which impede formation of free radicals by the non-radical decomposition of hydroperoxides. The concentration and quality of the stabilizing system in an analyzed polymer determines its residual service life. The most widely used antioxidants are sterically hindered phenols and bisphenols; other additives are combined with phenols mostly in synergistic mixtures. Hindered phenols are remarkably efficient in protecting saturated hydrocarbons against thermal oxidation. Additions in the range of 100–1,000 ppm of stabilizer are able to lengthen the induction time by one order of magnitude. The stabilization mechanism and trends of structure-property relationships are generally well understood, but quantitative (kinetic) approaches of a stabilizer’s efficiency are scarce and often based on simplifying hypotheses, for instance: the predominance of radical scavenging by the stabilizer in termination reactions, the stationary state assumption or the constancy of initiation rate (which is explicitly assumed or which derives from the steady-state assumption). It appears generally difficult to explain the very high stabilizer efficiency in the framework of such schemes where the rate of stabilizer consumption is expected to be equal (at least in a first approximation) to the initiation rate. Several mechanisms of synergy between two different antioxidants have been proposed, namely: 1)
2)
3)
4)
An interaction of both additives and formation of a new component, which then acts as a more efficient stabilizer. Example: aromatic amines + mercaptobenzimidazol. A redox mechanism. An oxidized form of a more efficient component of a synergic mixture is reduced by the presence of a less reactive component. Example: aromatic amines + phenols. Co-effect of chain-breaking antioxidants and chelating compounds reducing the rate of initiation by complexing transition metal ions and converting them to the less efficient initiators. The effect of annealing of a stabilized polymer sample on prolongation of its induction period may be included here, as well, provided that hindered phenols react with transition metals converting them to less efficient initiators. Interaction of acceptors of reactive free radicals and compounds that suppress the transfer reaction of an inhibitor radical with the substrate as it occurs in a system comprising antioxidants and polymer chain with conjugated system of double CQC bonds.
Role of Oxidation in Degradation of Polymers
5)
459
Synergism based on the mixture of a chain-breaking antioxidant (sterically hindered phenol) and a hydroperoxide decomposer (organic sulfides or phosphites).
The above mechanisms may act concomitantly in a given system, for example, as mechanisms 1 and 5, etc. The search for synergistic mixtures of stabilizers is an on-going area of research with an emphasis on providing non-toxic additives that are naturefriendly and which are well compatible with a given polymer. Proper selection of testing conditions revealed an outstanding efficiency of hindered amine stabilizers (HAS) [3,4] in the temperature range below 1301C as long-term heat stabilizers. An efficient component of a stabilizing system, sterically hindered nitroxide radicals, similar also as in their light protecting action, are supposed to capture alkyl radicals to give hydroxamic acid ethers, which in reaction with peroxyl radicals give back nitroxides. The rate of the former reaction is so high that it is capable of competing with the reaction of alkyl radicals and oxygen (reaction 2 of the Scheme 2). The variety of polyolefin-processing stabilizers has been widened recently through publications about the effect of tocopherols and captodative lactones of the benzofuranone type [5,6]. While the former were successfully examined and applied taking into account their antioxidation effect in biochemistry, the latter opened up a discussion about the mechanism of the action, which, similar to the case of hindered amines stabilizers, does not seem to be fully understood. A free radical being formed from the weakest C–H bond of the benzofuranone reacts fast with polymer alkyl radicals to give the product, which is unstable and decomposes into a polymer chain containing CQC unsaturation, and original lactone is regenerated (Scheme 3). This mechanism, which is based on multiple regeneration of the original stabilizer molecule, is formally identical with that proposed for HAS. However, while HAS act as relatively good antioxidants, the antioxidant effect of the lactone in polypropylene (PP) (Scheme 3) is rather poor. One important point should be stressed here: the efficiency of any stabilizing system depends very much on the removal or depletion of the defect structures in the polymer. An example is shown in Figure 1 where the case 5 mechanism (vide supra) of a synergistic mixture is theoretically depicted [7]. The line 2 shows that the effect of the synergistic mixture of two antioxidants on thermo-oxidation stability is negligible, if there occurs a relatively significant initiation of oxidation reaction in a way independent from the route taking place via hydroperoxides. An example of cellulose degradation initiated by hydrogen ions and water is shown below (Scheme 4). Here the first attack of hydrogen ions, which is much faster than the free radical initiation via oxygen, is focused on glycosidic oxygen atoms linking glucopyranosyl units. In the presence of water oxonium ions are cleaved and terminal semiacetals are formed, which are prone to subsequent oxidation by oxygen. An ionic pathway of polysaccharide degradation thus opens a route for an easy free radical oxidation of terminal groups. Considerable increase of
460
Jozef Rychly´ and Lyda Matisova´-Rychla´
bond dissociation energy ~ 330 kJ/mol
O C
O
OH
H O
C
P
+ O
O
O
C
C
O +P
R
+ PH
P= H
Scheme 3
Mechanism of action of captodatives benzofuranones.
0.010 20000
0.008
0.006
0.004
0.002
0.000
0.008
0.010
[D]0, mol/l 16000 induction time, s
1 12000
8000
2
4000
0 0.000
0.002
0.004
0.006
[InH]0, mol/l
Figure 1 The theoretical plot of induction time of oxidation determined for wi ¼ 0, (zero rate of initiation according to reaction 1 of Scheme 1) on composition of the mixture of inhibitors InH (chain-breaking antioxidant) and D (peroxide decomposer) having the total sum of concentrations 0.01 mol/l. The curve 2 below is the plot of induction times for the same values of parameters as for line 1 but wi ¼ 5 108 mol/l. The initial concentration of hydroperoxides was 0.001 mol/l.
461
Role of Oxidation in Degradation of Polymers
CH2OH O OH
OH
CH2OH +
O O
OH
O
H OH
O
H O +
OH
O
O
OH OH O
CH2OH
OH
O
CH2OH
cellulose CH2OH O OH O
O +
O H2O
H
OH
O
O
O
OH O
OH
H
OH
CH2OH H
OH O
O OH
CH2OH
OH
O
CH2OH
semiacetal CH2OH O
semiacetal + O2
OH O
OH OOH
OH terminal hydroperoxide (peracid)
Scheme 4 oxidation.
The hydrolytic scission of a cellulose chain providing the sites for free radical
stability may be achieved by a simple deacidification process, which prevents the formation of oxonium ions.
2. METHODOLOGY AND ANALYTICAL TECHNIQUES IN POLYMER STABILITY STUDIES When estimating the remaining service life of a polymer material for a particular application, the limiting value should be established of some material property such as tensile strength, elongation at break, electrical conductivity, permeability to low molar mass compounds, the average polymerization degree, etc., at which the polymer does not fail. The progress of polymer degradation may be followed by a wide variety of techniques, some of them being mentioned at the right column in the Bolland–Gee scheme (Scheme 2). There are techniques that directly monitor some of the elementary reaction steps such as, for example, oxygen absorption (reaction 2), differential scanning calorimetry (DSC) (reaction 3), chemiluminescence (reaction 11) analytical and/or spectral methods of determination of hydroperoxides, etc. The concept of a measurement of an induction period is based upon determination of critical time of the reaction progress that leads to the catastrophic change of the useful properties of the material. This may be demonstrated on the
462
concentration of hydroperoxides, rel.u.
Jozef Rychly´ and Lyda Matisova´-Rychla´
more stabilized sample
1.0
0.8 unstabilized sample 0.6 less stabilized sample
0.4
induction period
0.2
0.0 1000
10000
100000
time, s
Figure 2 Schematic representation of measurement of induction period in stabilized polypropylene.
model evolution of hydroperoxides for oxidized PP when using the Bolland–Gee scheme of oxidation. An unstabilized sample shows autoaccelerating increase of hydroperoxide concentration; the process shifts to longer times dependent on how efficiently the sample is stabilized by chain-breaking antioxidants (Figure 2). Induction times that are thus determined for a given temperature serve for a comparison of the efficiency of various stabilizing systems and help much in the development of new formulations. However, any extrapolation of such data to ambient conditions of material utilization based on Arrhenius plots should be carefully verified by long-term testing at a specified lower temperature. When cooled down, the polymer may go through different phase transitions and the error populated by such an extrapolation may be very high. A very fast testing of polymer stability is based on non-isothermal experiments (DSC, chemiluminescence) where the whole plot of the parameter followed may be visualized over a large temperature interval. The transfer of non-isothermal data to isothermal induction times involves a variety of more or less sophisticated approaches such as published in Ref. [8] or discussed later. The primary focus of the remainder of this chapter is on the application of chemiluminescence to study and investigate the role of oxidation in the degradation of polymers. The chemiluminescence method is a highly sensitive technique, and particularly effective in studying the early stages of polymer degradation. As discussed earlier in this chapter, free radical formation is an important step in the degradation cascade. Free radicals being formed in oxidized polymers possess usually high reactivity and their average concentration is mostly below the sensitivity limit of commercial electron spin resonance (ESR) spectrometers. However, when an independent route of the free radical generation is chosen (irradiation by gamma rays, UV or plasma discharge) under
Role of Oxidation in Degradation of Polymers
463
sample cooling, the concentration of free radicals becomes well detectable and their reactivity in the polymer matrix may be well assessed at increased temperature. Also the reaction of polymer radicals with some free radical scavengers such as nitrones and sterically hindered amines that converts them to the more stable nitroxides may be used in polymer degradation studies. The next chapter focuses on the complementary application of the ESR technique to the study of polymer degradation. Both these techniques, chemiluminescence and ESR spectroscopy, are perhaps generally less popular than some other molecular characterization techniques, such as infrared spectroscopy in relation to outdoor weathering studies and X-ray photoelectron spectroscopy (XPS) for surface degradation studies, both of which were discussed in the previous chapter, which serves as an introduction to the two more specific chapters on chemiluminescence and ESR.
3. MECHANISMS LEADING TO THE LIGHT EMISSION FROM THERMALLY OXIDIZED POLYMERS (CHEMILUMINESCENCE), SIMILARITIES AND DIFFERENCES WITHIN RESPECTIVE GROUPS OF POLYMERS Chemiluminescence is light emission from the relaxation of electrons populating excited states in an elementary step of a chemical reaction. Since, the process of population of excited states is related kinetically to the kinetics of the given chemical reaction, the emission of chemiluminescence over time should thus be related to the rate of the chemical reaction. It may be of associated interest that the chemiluminescence accompanying the oxidation of low molar mass hydrocarbons (ethyl benzene, tetralin, decalin and cumene) and its relation with the kinetics of their oxidation, mostly initiated by N,Nu-azo(bisisobutyronitrile), was reported by some Russian scientists in 1966 [9] almost in parallel with the first papers being published on chemiluminescence from polymers. These papers appeared in 1961 and 1964 when Ashby [10] and Schard et al. [11] reported several examples of the phenomenon from polymer chemistry. They underlined the need for a better understanding of the chemiluminescence from polymers but, at the same time, they also indicated an unexplored potential of the study of the light emission from oxidized polymers in order to better understand the oxidation process. The essential difference in interpretation of chemiluminescence during the oxidation of low molar mass materials lies in the fact that they have a well defined rate of initiator decomposition. The oxidation usually occurs in a kinetic region of oxygen surplus where no diffusion of oxygen to reaction sites is determining the reaction rate. In the case of polymer oxidation, however, a continuous accumulation of initiator (hydroperoxides) occurs, and the concentration of oxygen in the condensed system of oxidized polymer is governed by a considerably lower rate of its diffusion. For oxidation of low molar mass hydrocarbons, there were no doubts that the light emission originated from the disproportionation of peroxyl radicals according to the Russel’s scheme (Scheme 2, reaction 11). For oxidation of
464
Jozef Rychly´ and Lyda Matisova´-Rychla´
polymers, however, such a mechanism is one of several possible alternatives [12]. Liquid hydrocarbons and solid polymers usually have a similar solubility of oxygen, but the rate of oxygen diffusion is different. This may lead to the appearance of oxidation-time profiles, non-uniformity of the process due to higher local concentrations of hydroperoxides and heterogeneous distribution of stabilizers in the case of polymer oxidation [13]. Since the pioneering papers by Ashby and Schard new knowledge accumulated related to chemiluminescence from polymers has been described in several review papers [12–18] in which it has been established that chemiluminescence accompanies free radical reactions and that its observation is a function of oxygen concentration in the surrounding medium. A heat gain higher than 400 kJ/mol in an elementary reaction of oxidation is reported as being a necessary pre-requisite for light emission if the light emission comes from excited triplet carbonyl groups. It may be significantly lower when the light emitter is singlet oxygen. This is also the reason why the most preferred elementary reaction considered as the potential light-emitting process is disproportionation of secondary peroxy radicals, which occurs as discussed below (reaction 11 of the Scheme 2) (Scheme 5). In the reaction shown in Scheme 5, the excited triplet ketones and singlet oxygen may be formed simultaneously with released heat (450 kJ/mol). This is an optimum circumstance for the highest yield of the light emitted. One has to keep in mind, however, that deactivation of excited states occurs via the heat dissipated in collisions and that one photon (hn) is emitted per several millions or even billions of such deactivating procedures (Scheme 6). Regardless of this, an extremely sensitive photomultiplier coupled with a photon-counting unit is able to register it. This also pre-determines the extreme sensitivity of the chemiluminescence method. 6 1023 molecules or mers in one mole of a polymer indicates that the method is capable of successful monitoring of nano- or even pico-moles of compounds, which either oxidized or decomposed may provide the excited particles. The maximum of emission from excited triplet carbonyls occurs at 460 nm while that from singlet oxygen at 634 nm (dimol emission) and 1,270 nm (monomol emission) [19].
P1 CH
O•
O
+
•
P3 O
O
CH P4
P2
P1 C P2
Scheme 5
O
+
O2
+
H
P3 O
CH P4
The Russel scheme of secondary peroxyl radical disproportionation.
Role of Oxidation in Degradation of Polymers
465
P1 P1 C O
C O
+
C O
+
heat dissipated in collisions
P2
P2
P1 hν
P2
O2
O2
+ heat dissipated in collisions
O2
Scheme 6
+ hν
The light emission from excited triplet ketones and singlet oxygen.
Singlet oxygen (1 Dg state) is formed also in the decomposition of hydrogen peroxide that appears during the oxidation of polymers containing hydroxyl groups such as cellulose according to the following stoichiometric equations: CH
+
C
O2
+ HOOH
O
OH 2 HOOH
2 H2O
+
O2
The elementary reaction step, which involves the formation of singlet oxygen, is a reaction of superoxide anion radicals ( O2 ), which are the reaction intermediates of the above oxidation when performed in an alkaline medium. In the presence of water they may be converted to hydrogen peroxyl radicals HOO as follows:
O2 þ H2 O ! OH þ HOO
The exothermicity required for excitation of oxygen comes from recombination of hydrogen peroxyl radicals HOO þ OOH ! HOOH þ O2 The sequence of subsequent reactions [20] may lead either to ozone or to dimols of singlet oxygen: HOOH þ O2 ! O3 þ H2 O O3 þ HOOH ! ðO2 Þ2 þ H2 O Emission from dimols of singlet oxygen may be detected by photomultipliers used for measurement of chemiluminescence from hydrocarbon polymers with a maximum spectral sensitivity at 460 nm. The above scheme, however, requires the presence of at least one molecule of hydrogen peroxide in close vicinity to the two recombining peroxyl radicals and assumes a large heterogeneity of the oxidation process.
466
Jozef Rychly´ and Lyda Matisova´-Rychla´
As was already indicated, Scheme 5, which had been considered as the origin of the light emission arising from polymer oxidation, is not a unique mechanism. Quinga and Mendenhall [21] proposed that the luminescent process in the oxidation of polymers involves the disproportionation of two alkoxyl radicals, while Audouin-Jirackova and Verdu [22] expressed an idea that it might be the monomolecular fragmentation of alkoxyl radicals to form an alkyl radical and carbonyl groups in which the latter is formed in an excited state, similar to the case of dioxetane decomposition. There exists also the proposal by Osawa et al. [23] that the light emission arises from polynuclear aromatics acting as photosensitizers. They are sorbed to the oxidized polymer from the surrounding atmosphere during polymer storage. This opinion is based on a strong reduction of the initial chemiluminescence intensity when a polymer is extracted by low molar mass solvents. Blakey and George [24] suggested that chemiluminescence from oxidized polymer may involve the so-called CIEEL (chemically initiated electron exchange luminescence) mechanism, which involves the electron exchange between the potential activator and peroxide, which leads to a radical cation of an activator and a radical anion of a peroxide. The next step occurs as the rearrangement of the radical anion of a peroxide followed by charge recombination with formation of excited activator molecules. It appears that the role of the activator in oxidized polymer may be played by either isolated carbonyls or carbonyls attached to CQC. Quantum yield for the CIEEL mechanism appears to be three to five orders of magnitude higher than that for the reaction of a pair of peroxy radicals [25]. Other speculative mechanisms [26] may be proposed based on the presence of singlet oxygen and CQC in oxidized polymer. The reaction of the latter may lead to the transient formation of dioxetanes, the decomposition of which has an even higher quantum yield of luminescence than CIEEL mechanism [27]. In heterogeneous domains of oxidized PP, terminal dioxetane groups may be formed from 1,3-peroxyl hydroperoxides radicals in the sequence of reactions depicted in Scheme 7. In Scheme 7, the peroxidic O–O bond of the hydroperoxyl group is broken together with b-scission of the formed alkoxyl radical, and, further, ring closure of alkyl peroxyl diradical may occur. The process generates a hydroxyl radical, methylcarbonyl terminal groups (–CH2–CO–CH3) and dioxetane. The latter is unstable and decomposes into an excited triplet state of formaldehyde and/or excited triplet state of methylcarbonyls (Scheme 8). In the paper by Ptschelintsev et al. [28] on the oxidation of polyisoprene, it was reported that one recombination event of free radicals leads to scissions of CH3 CH2
C O OH
CH3 CH2
C O O
•
CH3 CH2
•
HO +
CH2
CH3
C
+ CH2
O
O
C CH2 O
Scheme 7 The alternative pathway of formation of the dioxetane moiety in an oxidised polypropylene chain.
Role of Oxidation in Degradation of Polymers
CH3
CH3 CH2
C CH2
O
O
467
CH2
+
O
C
CH2
O
Scheme 8 The scission of the dioxetane moiety leading to the light emission.
CH
CH2
CH
CH3
CH3
CH3
CH3
CH2
initiation
CH2
C
CH
CH2
+ O2 CH3
CH3 C
C
O
CH3
CH3
CH2 CH2
C
H
CH2 C
O
O•
CH2
H O CH3
CH3 C O
Scheme 9
CH2
C
CH2
+ O
H
The formation of hydroperoxy alkyl radicals and their exothermic cleavage.
approximately 30 C–C bonds. The authors expressed an idea that the chain scission is a matter of propagation of peroxyl radicals and not of b-scission of alkoxyl radicals. One of the possible pathways, which are strongly exothermic, is the scission of 1,3-hydroperoxy alkyl radicals, which are formed by intramolecular transfer of peroxyl radicals within a six-membered cyclic transition state (Scheme 9). The heat gain of the last sequence of the above reaction is surprisingly high (about 450 kJ/mol) and under conditions of reduced mobility of the polymer chain it may compete successfully with any mechanism of the light emission. Moreover, it is apparently linked with main chain scissions. Schard [11] suggested that the intensity of chemiluminescence is directly proportional to the number of tertiary carbons in a macromolecular chain, which naturally tend more to chain scissions. This rule has a limited validity since oxidized PS gives considerably lower chemiluminescence than polyethylene in an advanced stage of oxidation. Figure 3 shows how the elementary structure of the polymer affects the observed patterns of chemiluminescence response in oxygen at 1201C. As expected, the oxidizability decreases in the order polyisoprene o polybutadiene o polypropylene o polyethylene. However, it is difficult to understand why the maximum light emission is almost 2 lower for polybutadiene than for PP. The oxidation of polybutadiene occurs via secondary peroxyl radicals, while in
468
Jozef Rychly´ and Lyda Matisova´-Rychla´
120000
Intensity of CL, counts/s/3 mg
Polyisoprene 100000
120 °C, oxygen
80000 60000
Polypropylene
40000
Polybutadiene Polyethylene
20000 0 1000
10000 time, s
100000
Figure 3 Comparison of chemiluminescence runs from saturated and unsaturated hydrocarbon polymers having tertiary carbons (polypropylene, polyisoprene) in the main chain.
the case of PP tertiary peroxyl radicals predominate. If the Russel mechanism of the light emission (Scheme 5) is valid, the chemiluminescence from polybutadiene should be much more intense than that from PP. Recently, we have shown that non-isothermal chemiluminescence measurements for oxidized cellulose provide the same rate constants of cellulose degradation as may be measured from experiments on the decay of polymerization degree determined by viscometry. This may be also taken as indirect evidence that the light emission is somehow linked with the scission of polymer chains [29]. The intensity of chemiluminescence signal from a heated polymer and the kinetics of its change with time or temperature is determined by [30]: 1)
2) 3) 4)
The quality of the polymer, its photo-oxidation and thermo-oxidation history expressed in concentration of hydroperoxides, carbonyl groups or of other oxidized structures and terminal groups. The rate of an oxidative attack may then be related to the average molar mass and to its distribution, and to the ratio of amorphous/crystalline structures. Polymers cannot be simply ordered according to the intensity of light emission at a given temperature. The chemiluminescence-time patterns are related with the rate of sample oxidation, but they may differ from one to the next polymer. The quality of the polymer surface; for example, for a particular polymer the intensity of the signal will be different for film and for powder. The temperature and concentration of oxygen in the atmosphere surrounding the oxidized sample. The extent and quality of polymer stabilization.
Role of Oxidation in Degradation of Polymers
5)
469
A direct oxidation of polymer additive, which may occasionally give a much stronger signal than the oxidation of polymer itself. This is very important as it may lead to an erroneous relation between the rate of polymer oxidation and chemiluminescence intensity.
Qualitatively two different patterns of chemiluminescence intensity with time may be observed for polymer materials, namely, (a)
(b)
Autoaccelerating increase from the very low values to a maximum followed by the subsequent decay. Such measurements show an oxidative induction time and may be observed for such as the oxidation of polyolefins, polydienes and polyamides. All of these are polymers that have a relatively long length of oxidation chains (Figure 4). The initial level of chemiluminescence intensity at time t ¼ 0 usually corresponds to the extent of polymer preoxidation (Figure 4, see the case of polyamide 66 (PA 66)). A steady decay from an initial value of chemiluminescence intensity. Such decays are typical for the oxidation of polymers with heteroatoms in the main chain, such as poly(2,6-dimethyl-1,4-phenylene oxide) (Figure 5), which have comparatively a short length of oxidation chains, and also for polymers oxidized below their glass transition temperature. In a glassy state, the mobility of polymer segments is restricted. They are thus able to react in a limited reaction zone and the rate of the process should steadily decay. The chemiluminescence from the decay of peroxidic structures in pre-oxidized polymer samples occurring in an inert atmosphere belongs to this category as well.
PP
CL intensity, counts/s/1 mg
50000
40000
30000 PA 66
20000
PE 10000
0 10
100
1000
10000
time, s
Figure 4 Chemiluminescence oxidation runs at 1401C in oxygen for films of polypropylene (PP), polyamide 66 (PA 66) and polyethylene (PE) (logarithmic time scale).
470
Jozef Rychly´ and Lyda Matisova´-Rychla´
1600
CL intensity, Hz/1 mg
1400 1200
130 °C
1000 110 °C
800 600
90 °C
400 200 0 10
100
1000 time, s
Figure 5 Chemiluminescence oxidation runs for powder of poly(2,6-dimethyl-1,4-phenylene oxide) at different temperatures, oxygen (logarithmic time scale).
Following the Bolland–Gee Scheme 2 for non-inhibited oxidation occurring under stationary conditions, the following equation is frequently valid. wi þ k1 ½POOH þ kbi ½POOH2 ¼ k6 ½PO2 2
(1)
Provided that chemiluminescence intensity ICL is proportional to the rate of peroxyl radicals termination, that is ICL Ek6[PO2]2, which is often assumed in the literature, chemiluminescence intensity should achieve some quasi-stationary level when hydroperoxide concentration becomes stationary and its decay should correspond to consumption of oxidizable groups, PH, in a polymer. At the same time, the chemiluminometric curves of type (a), which are typical with an autoaccelerating increase of the light emission (Figure 4) are relevant for k1 ½POOH þ kbi ½POOH2 wi ,
(2)
while for type (b) of curves (Figure 5), where steady decay of chemiluminescence intensity from some initial value occurs, the following is valid k1 ½POOH þ kbi ½POOH2 wi ,
(3)
where wi represents the rate of consumption of oxidizable (defect) sites in a polymer (Scheme 2, reaction 1). In curves of the type (a) in Figure 4 the length of kinetic chains, which is the number of propagation steps of one free radical per one termination event, is sufficient to gradually develop a significant level of polymer hydroperoxides, while in type (b) plots (Figure 5), the concentration level of hydroperoxides in the polymer is rather low and the elementary step (reaction 1) in Scheme 2 represents the main oxidation event. One should be aware of the fact that in the case of oxidation of polyolefins and polydienes (case (a) earlier, see, e.g., Figure 4) after an autocatalytic development
Role of Oxidation in Degradation of Polymers
471
of the oxidation, the chemiluminescence intensity passes trough a maximum and then decays. No saturated level of the light emission is achieved, as is the case of initiated oxidation of low molar mass models with a constant initiation rate.
4. GENERAL CLASSIFICATION OF CHEMILUMINESCENCE FROM POLYMERS An oxidation test involving temperature ramp experiments in oxygen over a relatively large temperature range 40–2201C enables one to compare the oxidizability of different materials over a large temperature interval from the viewpoint of their chemiluminescence intensity. Such experiments were first reported by Wendlandt et al. [31–38]; unfortunately the papers did not attract appropriate attention. We have repeated the experiments in the temperature interval from 401C to 2201C using the rate of heating of 2.51C/min. Experimental runs of chemiluminescence intensity vs. temperature for different polymers (see Table 2) in oxygen are illustrated in Figure 6. Intensities of the light emission were normalized to 1 mg of sample. Oxidation of poly(methyl methacrylate) (PMMA), poly(ethylene terephthalate) (PETP) and PS gives very weak light intensity, medium values were obtained from cellulose, poly(2,6-dimethyl-1,4-phenylene oxide) and poly(trimethylsilyl propyne (PTMSP) containing silicon and CQC Table 2 Summary of temperature coefficients determined from Arrhenius’ plots of chemiluminescence intensity vs. temperature plots Polymer
Form
Zone I
Zone II
Zone III
Reference [34]
(kJ/mol)
Cellulose PTMSP PS PP PE PA 66 PA 6 PVP PPO PMMA PETP Irganox 1010 Dikaproyl-hexamethylene diamide
Sheet Powder Powder Film Powder Film Film Powder Powder Powder Powder Powder Powder
115 87 235 205 150 98 133 177 206 124 63 76 307
72 60 71 193 372 48 96 49 58 41 68 65 110
48 87 51 98 50 97 79 87 – – – 57 38
51 44–251 63–97 64
27–86
Notes: Cellulose (Whatman); PTMSP, poly(trimethyl silyl propine); PS, polystyrene; PP, polypropylene; PE, polyethylene; PA 66, polyamide 66; PA 6, polyamide 6; PVP, poly(vinyl pyrrolidone); PPO, poly(2,6-dimetyl-1,4phenylene oxide); PMMA, poly(methyl methacrylate); PETP, poly(ethylene terephthalate); Irganoxs1010 is a Ciba anti-oxidant.
472
Jozef Rychly´ and Lyda Matisova´-Rychla´
5000 PS CL intensity, Hz/1 mg
4000
3000
2000
1000 PETP PMMA
0 20
40
60
80
100
120
140
160
180
200
220
240
temperature, °C PA6 800000
CL intensity, Hz/1 mg
melting of polymer crystallites 600000 PP
PVP
400000 PE 200000
PA 66
0 20
40
60
80
100 120 140 160 180 200 220 240 temperature, °C
Figure 6 (A) Non-isothermal chemiluminescence runs for oxidation of polystyrene (PS), poly(ethylene terephthalate) (PETP) and poly(methyl methacrylate) (PMMA), in oxygen, heating rate 2.51C/min. (B) Non-isothermal chemiluminescence runs for oxidation of polypropylene (PP), polyamide 6 (PA 6), poly(vinyl pyrrolidone) (PVP), polyethylene (PE) and polyamide 66 (PA 66), in oxygen, heating rate 2.51C/min.
double bonds in a one monomer unit, while the most intense chemiluminescence was found for polymers like PP, polyethylene (PE), polyamide 6 (PA 6), polyamide 6,6 (PA 66) and poly(vinyl pyrrolidone) (PVP). Re-plotting the nonisothermal runs in Arrhenius coordinates reveals several different temperature zones in the evolution of chemiluminescence with temperature (Figure 7). For the case of PP we may distinguish a zone in the high-temperature region, which is
Role of Oxidation in Degradation of Polymers
473
14 I
I
ln I (I is in Hz/1 mg)
12
10 II
II 8
IV 6
2
III III
melting
4
IV
1
2 0.0020
0.0022
0.0024
0.0026
0.0028
0.0030
0.0032
-1
1/T, K
Figure 7 Arrhenius plots for non-isothermal chemiluminescence runs of oxidized polymers, (1) polypropylene, (2) polyethylene, in oxygen, heating rate 2.51C/min.
above the melting temperature of polymer and has a temperature coefficient around 205 kJ/mol (zone I); below the melting range, which occurs at 150–1551C, the temperature coefficient is slightly lower (193 kJ/mol) (zone II), while at 85–1251C there is a zone III that has a temperature coefficient of 98 kJ/mol. Temperatures below 801C involve zone IV, where the effect of preoxidation of the polymer and annealing of defect structures and hydroperoxides on initiation of oxidation takes place, which may be more important than the increase of chemiluminescence brought about by the increase of temperature. It is easy to realize that zones I and II at the highest temperatures may be attributed to the initiation of oxidation via the combined effects of scission of the weakest C–C bonds and unimolecular decomposition of hydroperoxides (zone II), while in zone III initiation probably occurs via bimolecular decomposition of hydroperoxides. One may also notice that any physical change of the polymer matrix (melting) as well as its oxidation history has an impact on the resulting representation of the chemiluminescence intensity–temperature run plotted in Arrhenius coordinates. The temperature coefficients given by Wendlandt [35] are from 44 kJ/mol for the low-temperature region to 251 kJ/mol for the hightemperature region. Data for temperature coefficients (activation energies) given in Table 2 show one common phenomenon when plotting chemiluminescence intensity vs. temperature in Arrhenius coordinates, namely, that in the higher temperature range the activation energy is usually higher than at lower temperatures, which is
474
Jozef Rychly´ and Lyda Matisova´-Rychla´
in accordance with Wendlandt’s results [34]. The polymers under study were free of stabilizers and were in the form as indicated in Table 2. Any preoxidation may be easily detected from non-isothermal experiments (see, e.g., zone IV in Figure 7, line 2 for PE). Pre-oxidized structures in a polymer bring about an initial fast decay of chemiluminescence intensity, which eliminates the increase of chemiluminescence intensity due to temperature increase. The same can be seen for PP, but the extent of preoxidation of the examined samples was considerably lower (30 vs. 200 mmol of hydroperoxides per kg of PP and PE, respectively). Polyethylene and PP melting interrupts the continuous change of chemiluminescence intensity. The increase of chemiluminescence intensity with temperature starts to prevail at temperatures above 1401C. Increase of chemiluminescence intensity for polyethylene in zone II has an unrealistically high-temperature coefficient (372 kJ/mol). This is probably caused by the oxidation of the surface layer of the polymer where a stepwise carbonization occurs. This layer prevents the escape of the volatiles from the polymer until it is disrupted. The rather abrupt release of volatiles is then accompanied by an increase of luminosity related with abnormal values of temperature coefficient. This is also the reason that non-isothermal thermogravimetry of PE in oxygen is difficult to study, as the measurement is disturbed by the unstability of the thermobalance caused by sudden releases of volatiles through the carbonized surface layer. Above 2001C the temperature coefficient attains a normal value around 150 kJ/mol. Of interest is the behavior of naturally aged PE powder after repeated irradiation by daylight under isothermal conditions. When we put the original sample of PE powder into the chamber of the chemiluminescence instrument, we can observe an initial burst of luminosity to rather high levels followed by a fast decay. This decay lasts about 20 min at room temperature. When the sample is exposed to daylight and its chemiluminescence measured again, we see that the chemiluminescence burst is repeated. The intensity of the bursts depends on the time of the exposure of the polymer powder to light (Figure 8). This observation has been seen for PP, polyamides, cellulose and many other polymers; the level of the chemiluminescence intensity bursts was found to be dependent on the extent of preoxidation [39]. The phenomenon is probably related to the charge recombination luminescence referred to by Mendenhall et al. [40] and Sewell et al. [41]. The latter authors used the phenomenon for measurement of the degree of curing of epoxy resins. Hydroperoxides are formed in each polymer containing aliphatic hydrocarbon chains on standing by various initiators, including light, heat, etc. This may be well detected by the non-isothermal chemiluminescence method in nitrogen. The analytical possibilities of this approach have not been fully utilized until recently [17]. Figure 9 demonstrates the fact that the chemiluminescence process occurs predominantly in the amorphous phase of the polymer. Low molar mass dicaproyl hexamethylene diamide is a fully crystalline compound; the chemiluminescence signal under isothermal conditions below the melting point (1361C) at 1301C is very low, but it becomes rather strong after the crystallites of
Role of Oxidation in Degradation of Polymers
475
35000 after 150 s after 220 s
after 800 s
CL intensity, Hz
30000 25000
original
20000
after 60 s
15000 10000 5000 0 0
1000
2000
3000
4000
5000
time, s
Figure 8 Chemiluminescence response of PE powder when illuminated by daylight at 401C, measured in oxygen.
100000
CL intensity (counts/s)
150 °C 10000
1000
100
130 °C
100
1000
10000
100000
Time (s)
Figure 9 Isothermal chemiluminescence from oxidation of dicaproyl hexamethylene diamide CH3–(CH2)4CONH–(CH2)6–NHCO–(CH2)4–CH3 (model of polyamide) in oxygen.
the diamide melt, which is the case of the isothermal experiment at 1501C. This may be also seen on non-isothermal run of the same compound (Figure 10), in which the diamide melts, and the chemiluminescence intensity increases by several orders of magnitude.
476
Jozef Rychly´ and Lyda Matisova´-Rychla´
100000
0
CL intensity, Hz
134.4°C -10
1000
-15 -20
Heat flow (W/g)
-5
10000
100 -25 10 80
144.8°C 100
120
140
160
-30 180
Temperature (°C)
Figure 10 Comparison of DSC record (solid line) in nitrogen and non-isothermal chemiluminescence run (dotted line) in oxygen for low molar mass diamide, the subject of figure 9.
5. COMPARISON OF CHEMILUMINESCENCE FOR ISOTHERMAL AND NON-ISOTHERMAL CONDITIONS WITH THOSE OBTAINED BY DSC Comparison of chemiluminescence isothermal runs with oxygen uptake and DSC measurements has been at the centre of interest since practical industrial applications of the chemiluminescence method were attempted. It is a fact that the best comparison may be achieved when studying polymers that give a distinct induction time of oxidation typical for autoaccelerating curves of a stepwise developing oxidation. This is the particular case of polyolefins, polydienes and polyamides. The theoretical justification for the search of a mutual relationship between the oxidation runs found by the various methods follows directly from the kinetic analysis of the Bolland–Gee scheme of polymer oxidation. For the rate of formation of alkyl (P ) and peroxyl (PO2 ) radicals we may obtain the following differential equations (the rate constants correspond to the reactions in Scheme 2) d½P ¼ kbi ½POOH2 k2 ½P ½O2 þ k3 ½PO2 ½PH k5 ½PO2 ½P 2k4 ½P 2 dt
(4)
d½PO2 ¼ kbi ½POOH2 þ k2 ½P ½O2 k3 ½PO2 ½PH 2k6 ½PO2 2 k5 ½PO2 ½P (5) dt As terms d½P =dt and d½PO2 =dt are negligible when compared with the hydroperoxide concentration changes they can be set to zero and thus one obtains the Equations (6) and (7).
Role of Oxidation in Degradation of Polymers
477
Subtraction of Equation (4) from (5) gives Equation (6) k2 ½P ½O2 þ k4 ½P 2 ¼ k3 ½PO2 ½PH þ k6 ½PO2 2
(6)
while addition of Equations (4) and (5) gives Equation (7) kbi ½POOH2 ¼ k6 ½PO2 2 þ k5 ½PO2 ½P þ k4 ½P 2
(7)
Note: such simplification is allowed only when we use Equations (4) and (5) for solution of differential equations involving more stable products, for example, that for concentration of hydroperoxides, as follows: d½POOH ¼ k3 ½PO2 ½PH 2kbi ½POOH2 (8) dt It has nothing to do with the existence of the stationary state for which concentrations ½POOH, ½PO2 and ½P should be constant. In the published literature efforts exist to plot the so-called total chemiluminescence intensity (TLI) (surface below the chemiluminescence curve) vs. amount of oxygen absorbed [15]. In some cases a straight line may be obtained. A more detailed examination of the Equation (6) reveals that rate of oxygen uptake is in fact involved, so that we have d½O2 ¼ k2 ½P ½O2 k6 ½PO2 2 ¼ k3 ½PO2 ½PH (9) dt The above equation is valid provided the rate of alkyl radicals self-termination is neglected, which is well possible when the polymer contains a sufficiently high level of oxygen. After integration we obtain the equation: Z ½O2 0 ½O2 ¼ DO2 ¼ k3 ½PO2 ½PHdt (10)
Once we assume that the main portion of heat is released in the propagation reaction, so that DSC k3 ½PO2 ½PH
(11)
and the chemiluminescence intensity I is proportional to the rate of peroxyl radicals disproportionation: I k6 ½PO2 2 we may assume that the oxygen uptake should be proportional to the surface below the DSC curve Z DO2 ¼ a DSCdt (12) and to the surface below the square root of chemiluminescence intensity line. In some laboratories chemiluminescence intensity and DSC signals from samples situated in one oven were obtained in parallel. Blakey and George [42], for example, presented the correlation between DSC signal and chemiluminescence (CL) intensity I during oxidation of PP. The quadratic dependence of I on DSC may be well seen in Figure 11.
478
Jozef Rychly´ and Lyda Matisova´-Rychla´
200
400
600
800
1000
1200
1400
1600
sqrt (CL intensity)
2
DSC
1
0
-1
-2 0
500000
1000000
1500000
2000000
2500000
CL intensity
Figure 11 Comparison of DSC and CL signal monitored from one oven at the same time of oxidation of polypropylene at 1451C (the original data taken from Ref. [42]).
The comparison of measurements for oxidation of polyisoprene indicates that the increase of chemiluminescence precedes that of oxygen uptake (Figure 12) and that a maximum of chemiluminescence is situated around an inflexion point of the oxygen absorption curve. The same appears to be valid for chemiluminescence and DSC runs of PP films oxidized at 120–1401C (Figure 13).
6. THE EFFECT OF INITIAL MOLAR MASS ON CHEMILUMINESCENCE RUNS The effect of molar mass and stereoregularity on the thermo-oxidation of polymers and on the chemiluminescence–time patterns has been investigated only rarely [44–46]. There are still some non-explained observations. For example, syndiotactic PP was reported [45,46] as being more stable than isotactic polymer. At 1401C, the maximum chemiluminescence intensity was achieved after 2,835 min for syndiotactic PP, while isotactic polymer attained the maximum after only 45 min. Atactic PP was reported to be more stable than the isotactic polymer [46]. An explanation has been offered that the structure of isotactic PP is much more favourable for autooxidation, which proceeds easier via a back-biting mechanism where peroxyl radicals abstract adjacent tertiary hydrogens on the same polymer chain.
Role of Oxidation in Degradation of Polymers
240 100 °C
200 180 160 140 120 100 80
90 °C
60 40 20
chemiluminescence intensity, counts/s/3 mg
50000
220 oxygen absorbed, ml/g of polymer
479
10000
30000
20000
10000
0 30000
0 0
40000
20000 time, s
Figure 12 Chemiluminescence intensity and absorption of oxygen [43] scans for oxidation of polyisoprene in oxygen, temperatures 901C and 1001C.
140 °C
0.4
150000
DSC,mW
CL intensity, Hz
130 °C
0.2
0.0
120 °C
-0.2 0
3000
6000
100000
50000
0 9000
time, s
Figure 13 Comparison of DSC and chemiluminescence scans of the oxidation of polypropylene films.
However Iring et al. [47] found that the induction period for oxidation of solid isotactic PP is longer than that for atactic polymer. Their result is in accordance with the high crystallinity of isotactic PP and with the resistance of its crystalline zones to oxidation.
480
Jozef Rychly´ and Lyda Matisova´-Rychla´
CL intensity, counts/s
120000
40 000
80000 80 000
40000
180 000
0 0
10000
20000
30000
time, s
Figure 14 Chemiluminescence oxidation runs at 1201C in oxygen for polypropylene powder samples of different molar mass. The numbers against each curve express the average molar mass in g/mol.
On well characterised non-stabilized PP samples [48] having molar mass within 45–180 kg/mol with differing tacticity and crystallinity, we can see that the increasing molar mass leads to an increase of induction time and reduction of the maximum chemiluminescence intensity (Figure 14). The polymer with higher average molar mass appears to be more stable than that with lower molar mass. This may be ascribed to the effect of increased concentration of more reactive terminal groups, which promote initiation of thermal oxidation.
7. THE EFFECT OF TEMPERATURE ON CHEMILUMINESCENCE INTENSITY; THE MUTUAL RELATION OF ISOTHERMAL AND NON-ISOTHERMAL STUDIES Increasing temperature shortens the induction time and increases the maximum chemiluminescence intensity in the case of chemiluminescence of PP powder (type (a), see Figure 15), whereas it increases the initial chemiluminescence intensity in the case of poly(2,6-dimethyl-1,4-phenylene oxide) (type (b), see Figure 5). This is perhaps not surprising as the rate of oxidation reaction increases with temperature as well. For the mechanism of chemiluminescence in which the intensity of light emission I is proportional to the rate of oxidation w and, therefore, to the concentration of hydroperoxides, the following function of time t may be deduced: const I ¼ Fw ¼ const½POOH ¼ (13) 1 þ B expðktÞ
Role of Oxidation in Degradation of Polymers
18000
481
110
16000
CL intensity, Hz
14000 12000 10000
100
8000 6000 90
4000
80
2000 0
0
200000
400000 time, s
600000
800000
Figure 15 Chemiluminescence oxidation runs for polypropylene powder at different temperatures; the average molar mass of the polymer is 180 kg/mol.
where B is another constant dependent on initial concentration of hydroperoxides. The rate constant k, which involves the rate constant of bimolecular decomposition of hydroperoxides kbi from 2 may thus be determined, the Scheme
so that we find the value of d I=I max =dt max , which is the slope of chemiluminescence–time record at its inflexion point. This ratio is function of k as follows: 3 2 I d 6 I max 7 1 6 7 (14) ¼ k 4 dt 5 2 max
The set of the rate constants k determined for experimental runs of Figure 15 and their comparison with the rate constants of hydroperoxide decomposition determined by other methods may be seen in Table 3. When we take into account that PPs of different origin were examined, the agreement seems quite satisfactory. This agreement is valid for faster decomposing peroxides, which are the species determining the resulting rate of oxidation [49]. Equation (13) appears to be a good approximation for describing isothermal chemiluminescence kinetics for homogeneous systems where oxidation takes place uniformly. However, as has been shown by several authors [53–58], the different sections of a polymer sample may oxidize with its autonomous kinetics determined by different rates of primary initiation. A chemiluminescence imaging technique revealed that the light emission may be spread from some sites of the polymer film and the isothermal chemiluminescence vs. time runs are then modified, particularly in the stage of an advanced oxidation reaction [59].
482
Jozef Rychly´ and Lyda Matisova´-Rychla´
Table 3 The rate constants k determined from chemiluminescence experiments of Figure 15 and Equation (14) and the rate constants k of decomposition of hydroperoxides from literature Temperature (1C)
k(s1) (by CL)
k(s1) (from Refs. 51–53)
Reference
80 85 90 100 110
1.7 105 – 4.7 105 1.1 104 2.4 104
– 3.2 105 2.8 105 8.7 105 3 104
– [51] [50] [51] [52]
A heterogeneous model of polymer oxidation has been developed and described involving both the initiation and light emission spreading [58,59]. Within this model an idea is proposed that oxidation is initiated faster in regions of lower molar mass and at zones of higher concentrations of eventual structural defects. This might explain how the spreading of the light emission takes place. The initial oxidation attack is focused on the regions of lower molar mass, which may be found at, for example, the sample edges of cut polymer foils or around the pre-oxidized domains. In the former case, an increased level of polymer-free radicals generated by mechanical degradation may also be responsible for the development of the oxidation process. Hydroperoxides formed at the border of such domains will initiate the oxidation of the polymer molecules in their close proximity, which will lead to a reduction of the molar mass, and the oxidation attack continues within this lower molar mass region and adopts the character of spreading. The mechanism of spreading of oxidation via the gaseous phase in the close proximity to the polymer surface has been proposed also [15], however, the molecules responsible for that were not specified. Kinetics based on the idea of spreading is formally based on the model of development of an infectious disease among human population [59,60]. The formalism of chemical kinetics, however, should be treated with a care as a similar equation can be derived from the homogeneous model assuming bimolecular decomposition of hydroperoxides as an initiating event. To see if oxidative spreading could take place between different polymers, initiation of stabilized PP using a piece of unstabilized polyamide 6 has been performed. However, polyamide cannot initiate oxidation of PP even if oxidized polyamide is in direct contact with PP [15].
8. RELAXATION EXPERIMENTS (JUMP CHANGES OF CONCENTRATION OF OXYGEN, TEMPERATURE AND HUMIDITY) AND RATE CONSTANTS OF RESPECTIVE ELEMENTARY REACTION STEPS The difference between the chemiluminescence response of polyisoprene and cellulose on jump changes of atmosphere from nitrogen to oxygen (cf. Figure 16 and Figure 17) is probably due to the fact that the rate constant k6 ok4 for
Role of Oxidation in Degradation of Polymers
100 °C
25000
CL intensity, counts/s/1 mg
483
nitrogen 20000
oxygen nitrogen
15000
10000
5000 oxygen 0 10000 time, s
Figure 16 Relaxation changes of chemiluminescence intensity for oxidized polyisoprene during replacement of oxygen by nitrogen and vice versa.
polyisoprene oxidation while opposite is true for cellulose. One should bear on mind that k6 and k4 are rate constants of alkyl and peroxyl radicals termination, respectively (see Scheme 2). The ratio of the earlier constants follows from relaxation experiments by George [54]. In the case of polydienes when a nitrogen atmosphere is replaced by oxygen, its chemiluminescence intensity rises fast to a particular level from which a maximum is attained within a particular time (Figure 16). The picture with cellulose is different; when switching to oxygen the chemiluminescence intensity jumps to some level from which it decays steadily to some equilibrium level (Figure 17). The initial increase depends on the time sample is in nitrogen and has a tendency to saturation. This is an indication that peroxyl radicals recombine faster than alkyl radicals, that is k6 4k4 .
9. THE EFFECT OF ANTIOXIDANTS AND POLYMER STABILIZERS Antioxidants shift the autoaccelerating increase of chemiluminescence intensity to higher time. This is due to reactions 12 and 13 of the Bolland–Gee mechanism (Section 1, Scheme 2) in which peroxyl radicals and hydroperoxides are scavenged until antioxidants InH and D are consumed. A typical example of such a behavior occurs for samples of PP containing 0.1 %wt. of Irganoxs 1010 (a sterically hindered phenol) (Figure 18 and Table 4). The presence of antioxidants usually reduces the maximum chemiluminescence intensity [61,62]. This may be explained by the quenching effect of the antioxidant on excited carbonyls, but it may be also related to the mechanism of oxidation of stabilized PP. Stabilizers in
484
Jozef Rychly´ and Lyda Matisova´-Rychla´
800000 oxygen
CL intensity, counts/s
600000
nitrogen
oxygen 400000
nitrogen
200000
0 0
1000 2000 3000 4000 5000 6000 7000 8000 9000 10000 time, s
Figure 17 Relaxation changes of chemiluminescence intensity for oxidized cellulose containing magnesium carbonate at 1801C during replacement of oxygen by nitrogen and vice versa.
160000 140000
non-stabilised
CL intensity (Hz)
120000 100000 80000 60000 40000 20000
stabilised
0 10
100
1000
10000
100000
time (s)
Figure 18 Chemiluminescence during oxidation of a non-stabilized polypropylene film and a stabilized film containing 0.1% (w/w) of the phenolic antioxidant Irganox 1010 at 1401C, in an oxygen atmosphere.
485
Role of Oxidation in Degradation of Polymers
Table 4 The effect of antioxidants on induction time of oxidation of polypropylene determined at 1501C from chemiluminescence measurements Antioxidant (% wt.)
tind (s at 1501C in oxygen)
Irganox Irganox Irganox Irganox Irganox
6,206 17,018 39,742 555 1,753
1010, 1010, 1010, 1076, 1076,
0.1 0.25 0.5 0.25 0.5
Notes: tind denotes time of induction period.
intensity of chemiluminescence, counts/s
15000
1
2
10000
5000
0 0
200000
400000
600000
800000
time, s
Figure 19 Chemiluminescence from oxidation of polypropylene containing 0.5 % wt. of Irganox 1010 at 1501C in oxygen. Line 1 represents the original polymer film; line 2 is the same sample after 7,890 s of annealing at 1301C.
a polymer may be distributed differently in different phases of a polymer, the highest concentrations being present in amorphous domains of a polymer with the lowest molar mass. (The case of reduction of chemiluminescence intensity for stabilized polymers of the chemiluminescence curves of the type (b) (Figure 5) has not yet been studied.) The observation of an unusual effect occurring as a consequence of preannealing on the induction time of oxidation of PP stabilized with Irganox 1010 (Figures 19 and 20) needs to be taken into account when searching for correlations between induction periods from chemiluminescence and oxygen uptake for oxidation of PP stabilized with different types of antioxidants.
486
Jozef Rychly´ and Lyda Matisova´-Rychla´
2 hrs of annealing at 130 °C in oxygen 2
induction time, s
100000
1 10000
1000
0.0
0.1
0.2 0.3 0.4 concentration of Irganox 1010, % wt.
0.5
Figure 20 An increase of induction time of oxidation of polypropylene stabilized by Irganox 1010 (points 1) due to prior sample annealing at 1301C (points 2) in oxygen. The induction time corresponds to the time of cross-section of the straight line passing the CL inflexion point and time axis. It was determined for an oxygen atmosphere and temperature 1501C.
This sometimes does not appear very satisfactory [61–63]; several alternative explanations of the annealing effect have been considered: (i) Annealing in an inert atmosphere as a way of removing other reactive sites like hydroperoxides, the terminal unsaturations, etc., from a polymer so that the quality of the polymer after annealing is better. This was suggested by Zlatkevich [64] who reported that samples of PP annealed at 1501C in nitrogen gave higher induction times than non-annealed ones. We have repeated his experiments performing the annealing of non-stabilized PP in an inert atmosphere of nitrogen for 6,500 s at 1301C, then the atmosphere was switched to oxygen. We have shown that there is no substantial difference in induction time for non-annealed and annealed samples and that this probably does not appear to be the case if the polymer is free of phenolic stabilizer. (ii) The complexation effect of a stabilizer on residual metallic catalysts as proposed by Gugumus [65] and others [66]. The pro-initiating effect of the residual catalyst is thus converted to that of an inhibiting one. The complexes should be formed only below a certain temperature above which the effect does not exist. (iii) Audouin et al. [67] explain the difference in the efficiency of phenolic stabilizers below and above melting temperature with the change of the inhibitor’s concentration in the partially crystalline substrate. The average concentration of a stabilizer in amorphous domains is higher below the melting temperature than above and there occurs post-homogenization of a stabilizer in the polymer melt.
Role of Oxidation in Degradation of Polymers
487
The alternatives (ii) and (iii) may contribute to the effect of annealing in their own way. Non-homogeneous dispersion of a stabilizer in the polymer in terms of the formation of aggregates and/or associates appears quite probable. Annealing should contribute to molecular dispersion of the inhibitor even to the vicinity of larger polymer molecules. In favour of such a hypothesis is the more pronounced effect of annealing in a nitrogen atmosphere than in an oxygen atmosphere. One can understand that a stabilizer in oxygen at elevated temperature is depleted rather fast not only in reaction with oxidation products of PP, but also in direct interaction with oxygen. Provided that the stabilizer is heterogeneously dispersed and concentrated in micro-domains, it may happen that at some sufficiently high temperature its molecules diffusing out of the domain react faster directly with oxygen before they can protect the oxidized polymer. Annealing supports the homogenization at a molecular level and the stabilizer is thus more ready to react with polymer peroxy radicals and to suppress the formation of associated hydroperoxides. They apparently belong to those of fast decomposing initiating moieties in PP.
10. ISOTHERMAL KINETICS OF POLYMERS OXIDATION AND ITS RELATION TO THE CONCENTRATION OF OXYGEN IN SURROUNDING ATMOSPHERE The chemiluminescence intensity accompanying the oxidation of polymers is usually dependent on the concentration of oxygen in the surrounding atmosphere (Figures 21 and 22). This is confirmed by restricting the diffusion 120000 100%
CL intensity, counts/s/3 mg
100000
80000 50% 60000
40000 33.3% 20000
16.6%
0 0
5000
10000
15000
time, s
Figure 21 Chemiluminescence from polybutadiene: the effect of oxygen concentration in a mixture with nitrogen, 1301C, total flow of gas 3.6 l/h, the numbers denote the volume percent of oxygen in the mixture with nitrogen.
488
Jozef Rychly´ and Lyda Matisova´-Rychla´
100% 83.3 CL intensity, counts/s - 5.6 mg
30000
66.6 50 33.3
20000
16.6 13.3 10 6.6
10000
3.3 0 0 2000
3000
4000
5000
6000
7000 8000
time, s
Figure 22 Continual changes of the intensity of chemiluminescence signal with concentration of oxygen in the surrounding atmosphere, 1801C, for Whatman cellulose paper. Numbers are % vol. of oxygen in the mixture with nitrogen.
of oxygen to the corresponding reactive sites, but a quantitative interpretation is still missing. In Figure 21, which shows the chemiluminescence from polybutadiene, the maximum values of chemiluminescence intensity decrease with decreasing concentration of oxygen in a mixture with nitrogen; a similar observation was made with polyisoprene. In the case of oxidation of (Whatman) cellulose, when we reduce the concentration of oxygen in the mixture with nitrogen in a stepwise manner we observe a stepwise reduction of equilibrium chemiluminescence intensity (Figure 22). The plot of chemiluminescence intensity vs. concentration of oxygen in the surrounding atmosphere has either a linear or a curved dependency on the quality of the polymer examined (Figure 23). Assuming that the reaction occurs under homogeneous conditions, it appears quite clear that in the case of sufficiently high length of kinetic chains, the primary appearance of free radicals by the rate wi (Scheme 2) is very soon replaced by the decomposition of hydroperoxides and the process has the character of a ‘‘closed loop’’ [68]. If we presume that oxidation of polymer PH takes place according to the Scheme 2 of Bolland–Gee mechanism, in which reactions 2, 3, 5, 6, 7, 8, 9 and 10 predominate, involving initiation, propagation and termination of the free radical process. The production of primary radicals by the reaction 1 is governed rapidly by decomposition of hydroperoxides. From the shape of kinetic runs it may be assumed that decomposition of hydroperoxides has the character of a bimolecular reaction (reaction 5) even in a very short time after the start of experiment.
489
Role of Oxidation in Degradation of Polymers
35000 100000
30000 Whatman cellulose, 180 °C
80000
25000 polybutadiene, 130 °C
60000
20000 15000
40000 10000 polyisoprene, 100 °C
20000
5000
equilibrium chemiluminescence intensity from Fig.5 counts/s (5.6 mg)
chemiluminescence intensity Imax, counts/s, 3 mg
120000
0
0 0
20
40
60
80
100
concentration of oxygen in the mixture with nitrogen, % vol.
Figure 23 Plot of maximum and equilibrium chemiluminescence intensity and its dependence on concentration of oxygen in a mixture with nitrogen.
Analysis of the Bolland–Gee scheme involving the self-termination of peroxyl radicals and peroxyl radicals with alkyl radicals using Equations (4–8) leads to the relation k4 ½PO2 2 ¼
kbi ½POOH2 k5 k3 ½PH k5 ½PO2 þ 1þ k2 ½O2 k4 k2 ½O2
(15)
Provided that we neglect the third term in the denominator, which is significant only at relatively low concentrations of oxygen in polymer we obtain k4 ½PO2 2 ¼ mkbi ½POOH2
(16)
where m¼
k2 ½O2 . k2 ½O2 þ k5 =k4 ðk3 ½PHÞ
(17)
is the function of concentration of oxygen dissolved in polymer. We have to remind one here that the above equation presumes that the initiation of the process is represented by a bimolecular decomposition of polymer hydroperoxides POOH, the transfer reaction of alkoxyl radicals PO to polymer PH is considerably faster than the corresponding reaction of peroxyl radicals, the concentration of alkoxyl radicals can thus be neglected if compared to that of peroxyl radicals and,
490
Jozef Rychly´ and Lyda Matisova´-Rychla´
differential terms for the rates of alkyl radicals and peroxyl radical concentration changes were assumed to be zero taking into account that these rates are negligible if compared with the rate of change of hydroperoxide concentration. Thus, for the time dependence of hydroperoxide concentration [POOH] we ultimately obtain the equation (see Equation (13)). X ½POOH ¼ (18) 1 þ Y expðktÞ where X ¼ ½POOH1 , Y ¼ ð½POOH1 ½POOH0 Þ=½POOH0 , while sffiffiffiffiffiffiffiffiffi rffiffiffiffiffiffiffiffiffiffi k3 ½PH m mkbi ½POOH1 ¼ and k ¼ k3 ½PH 2 k4 kbi k4
(19)
The effect of oxygen concentration is thus included in a constant m, which modifies both the resulting maximum of the chemiluminescence intensity and the apparent rate constant k of hydroperoxide decomposition.
11. THE EFFECT OF ALKALINE ADDITIVES ON CHEMILUMINESCENCE RUNS: A POSSIBLE IMPACT For developing this particular part of our discussion, which has an important impact on the formulation of the more precise mechanism of chemiluminescence from oxidized polymer, we report initially on some studies undertaken using the biopolymer, pullulan [69], a polysaccharide and cellulose. Oxidized pullulan at 1901C yields a chemiluminescence–time record in which the CL increases with time from a rather low value to a maximum that occurs around 30,000 s. This is then followed by a decay in the CL intensity. If the pullulan contains methyl methoxy magnesium carbonate (MMMC) and/or MgO, the maximum chemiluminescence intensity is reached much sooner (at 1,300 s), and the level of CL intensity is almost 5 times higher (Figure 24). It is of interest that after some time, both records coincide. It is worth noticing that pullulan after impregnation with MMMC is significantly more stable. This may be seen on Figure 25, where gel permation chromatography (GPC) scans are shown for the original pullulan (line 1) and for pullulan which was heated in oxygen from 401C to 2201C with a rate of heating of 2.51C/min (line 2). When the same procedure was performed with pullulan impregnated with MMMC (line 3), the maximum of the molar mass distribution curve is significantly shifted to higher values. The same may be observed with magnesium carbonate in cellulose [70] (Figure 26). The chemiluminescence intensity at a given temperature increases with pH of the sample almost linearly. As it is evidenced by DSC, the sample with pH 7.2 is the least stable. Figure 26 is also a demonstration of the much higher sensitivity of the chemiluminescence method when compared with DSC. DSC exotherms, which accompany the final stages of the cellulose decomposition
chemiluminiscence intensity, counts/s
Role of Oxidation in Degradation of Polymers
491
1 300 s 40000 2
30 000 s
20000
1 0 0
20000
40000
60000
80000
time, s
Figure 24 Comparison of isothermal chemiluminescence intensity for pullulan (1) and pullulan impregnated by methoxy magnesium methyl carbonate (2) from a 5% solution in methanol; initial molar mass of pullulan 404 kg/mol, oxygen atmosphere, temperature 1901C.
1.5
1
w (log Mw) [-]
1.2
3
0.9
2
0.6
0.3
0.0 3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
log Mw
Figure 25 Comparison of the molar mass distribution from original sample of pullulan (1) and that heated by the rate 2.51C/min from 401C to 2201C (2) in oxygen directly in chemiluminescence instrument. The line 3 is the same experiment with sample impregnated with MMMC.
492
Jozef Rychly´ and Lyda Matisova´-Rychla´
1200000
Whatman cellulose with Mg(HCO3)2 at different pH
14 pH=9.2 12 10 8
800000 6
pH=9.8
4
600000
2 400000
pH=7.2
heat flow, mW
CL intensity, counts/s
1000000
0
200000
-2 -4
0 50
100
150
200 250 temperature, °C
300
350
Figure 26 Comparison of non-isothermal chemiluminescence experiments with DSC runs in oxygen for Whatman cellulose of different pH due to the presence of magnesium carbonate.
and carbonisation, are seen at temperatures above 3001C, while the chemiluminescence signal is easily observable at considerably lower temperatures. What is the reason of a significant increase of chemiluminescence when magnesium ions in alkaline medium are added to polysaccharide? We know that the active compound is in both cases MgO, which remains in the sample after its thermal treatment. When that calcium carbonate giving a pH around 9 is used instead, in a similar manner to magnesium carbonate, no increase of chemiluminescence above the reference level was observed [70]. Cellulose impregnated by magnesium carbonate and subsequently treated with hydrochloric acid to have pH around 7 did not give an increase either [70]. The difference between the atomic volumes of Mg and Ca, which are 13.97 and 29.9 cm3/mol, respectively, and between Pauling’s electronegativities, which are 1.00 for Ca and 1.31 for Mg, together with an alkaline medium are obviously the reason of the observed chemiluminescence uptake due to Mg ions. The above observations may be taken as a demonstration of the fact that chemiluminescence emission from an oxidized polymer reflects at least two initiating processes. First is the process that corresponds to the statistical initiation of a free radical reaction occurring via isolated hydroperoxides distributed along the main polymer chain. This usually leads to a considerably lower yield of light emission than the process that occurs with hydroperoxides having in their b-position substituents such as hydroxyls, carbonyls, carbamido groups, etc (see, e.g., Figure 6). As such groups easily appear at the chain end of the polymer, this may be the reason why the chemiluminescence intensity may be proportional to the average molar mass of the polymer. In the oxidation of
Role of Oxidation in Degradation of Polymers
493
pullulan it is even suspected that decomposition of such hydroperoxides may occur via intermediate dioxetanes, the formation of which is supported by an alkaline medium and by the presence of magnesium ions. Hydroperoxides having in their b-position some of the above groups represent usually a fraction of the overall hydroperoxidic groups and obviously, they are less stable than isolated hydroperoxides. This is in accordance with the study by Billingham et al. [71] which showed that chemiluminescence from PP originates in a relatively small fraction of reactive peroxides. Thus, the most intense light emission during oxidation of some polymers probably comes from an advanced phase of the oxidation process when hydroperoxides are formed in b-position to carbonyl, hydroxyl, hydroperoxyl, carbamido and carboxyl groups. This is easily possible with aliphatic hydrocarbon polymers, polyamides, but almost excluded with polymers which depolymerize during oxidation (e.g., polymethyl methacrylate and PS)
12. CONCLUSIONS AND OUTLINE OF THE FURTHER PERSPECTIVES We will now formulate the mechanism of the light emission taking into account all the facts presented in this chapter. It will be exemplified using the case of polysaccharides. The oxidation of polysaccharide on carbon 6 is obviously rather a slow process at low temperatures and starts to be important at temperatures above 1001C. The stoichiometry of the reaction for cellulose is depicted in Scheme 10. The degradation process has a free radical mechanism. It is initiated by free radicals Pd that appear due to, for example, hydroperoxide decomposition induced thermally or by trace amounts of metal ions present in the polysaccharide. One cannot exclude even direct interaction of the polysaccharide with oxygen in its ground triplet state with biradical character. Hydroperoxidic and/or peracid moieties are easily formed by oxidation of semiacetal chain end groups. The sequence of reactions on carbon 6 of polysaccharide structural unit that ultimately may lead to chemiluminescence is shown in Scheme 11. The most probable elementary step from which chemiluminescence is emitted is disproportionation of secondary peroxyl radicals, which may be formed only on carbon 6 of the glucopyranosyl unit. According to various authors, who accept the Russel Scheme 5 of disproportionation of secondary peroxyl radicals as a possibility leading to the light emission, it may be deduced that carboxylic acid, 6
CH2OH 5
4
O
O
OH 3
1 2
OH
HO
OH
C
O2
O OH O CH2OH
O
O
+ H2O OH
O OH
O OH
O
O OH
O
CH2OH
Scheme 10 The formation of acid sites and water from oxidation of carbon 6 of the glucopyranosyl unit. Numbers denote the respective carbon atoms of glucopyranosyl unit.
494
Jozef Rychly´ and Lyda Matisova´-Rychla´
R1CH2OH + P•
PH
+
R1CHOH OO•
R1CHOH OO• 2 R1CHOH
+
R1CHOH
O2 O R1COH
OH +
R1CHOH
R1CH R-COOH
Scheme 11
R-COO−
+
+ O2
O + H2O
+ H
The mechanism of the formation of acid sites in oxidised cellulose.
excited triplet aldehyde, singlet oxygen and water are formed when this scheme is applied to polysaccharides. The simultaneous formation of carboxylic acid and water may further promote a subsequent heterolytic cleavage of C–O–C bonds linking glucopyranosyl units. Notice that peroxyl radicals, which are potentially formed on carbons 1, 2, 3, 4 and 5, are tertiary peroxyl radicals, which in their recombination give oxygen and two oxyl radicals or dialkyl peroxide, respectively, via a radiationless route. An easy peroxidation of terminal aldehydic groups A in the Scheme 12 in polysaccharides tend us to consider a chemiluminescence reaction which has a considerably higher quantum yield of light emission than disproportionation of secondary peroxyl radicals. This may be the decomposition of dioxetanes, the chemiluminescence of which was examined on relatively stable samples of, for example, tetramethyl dioxetane. Such dioxetanes may be prepared from the corresponding b-bromohydroperoxide in the presence of alkaline Ag2O suspension [72]. Provided that terminal end groups A are peroxidized we obtain b-hydroxy hydroperoxide. In the presence of alkaline MgO a similar reaction may occur for which the magnitude of magnesium ions seems to be favourable for the mechanism shown in Scheme 12 to occur. Comparison of chemiluminescence runs from synthetic polymers and from polysaccharides allows for formulation of the Scheme 13 of the appearance of chemiluminescence from oxidized polymers. The weak light emission comes from both the oxidation of secondary carbon atoms occurring statistically along the main polymer chain or from terminal groups, which have increased reactivity towards oxidation. Once some oxidized moiety is formed, the brighter light emission arises from its subsequent oxidation leading to heavily oxidized products. Even though we have adopted an idea of dioxetane decomposition as the most probable source of the bright light emission,
495
Role of Oxidation in Degradation of Polymers
CH2OH O
OH
O
O
H+
O
OH
O
O
H2O
O
OH
OH
+
OH
+
O
OH
O
+ H
CH2OH
OH
CH2OH
OH
OH
CH2OH
OH
(semiacetal groups A) CH2OH
CH2OH O A + O2
OH O
O
MgO
OH
OH
OH O
OOH
O
+ Mg(OH)2
O OH
CH2OH O
CH2OH O
OH
OH
O
O
OH C
OH O
O CH
O
O
Scheme 12 Hydrolytic degradation preceding free radical oxidation of cellulose macromolecules.
weak chemiluminescence from peroxyl radicals recombination
bright chemiluminescence from intermediate dioxetanes or similar light emission precursors
oxidation oxidation carbonyl, hydroxyl, secondary carbon atoms heavily oxidized via hydroperoxides carboxyl groups in the polymer chain of their β−positions products
oxidation via hydroperoxides
terminal groups of macromolecules
Scheme 13
Mechanism of the light emission from polymers.
the proper mechanism explaining any aspect of the process will need probably some modifications. It thus appears that a measurement of the light emission from the oxidized polymers opens a new possibility in understanding of the oxidation and
496
Jozef Rychly´ and Lyda Matisova´-Rychla´
degradation mechanism. However, a better insight into the process by which the light is released from an oxidized polymers still prevents greater and even industrial applications of the method. The potential of an extreme sensitivity of the chemiluminescence method, however, is very promising, particularly when combined with other approaches used for the polymer characterization.
ACKNOWLEDGEMENTS We would like to thank Dr. I. Lacik from Polymer Institute of the Slovak Academy of Sciences who undertook the GPC experiments, Dr. Jose Manuel Gomez-Elvira from CSIC Madrid, Spain who supplied PP of various initial molar masses, Dr. M. Pletenı´kova´ who performed some chemiluminescence measurements, Papylum project of the 5th EU community programme, Grant Agency VEGA for the grants No. 2/5109/25 and 2/6115/26 and the project KNIHA-SK.
REFERENCES 1 M. Laza´r, T. Bleha and J. Rychly´, Chemical reactions of natural and synthetic polymers. In: T.J. Kempp and J.F. Kennedy (Eds.), Ellis Horwood Series in Polymer Science and Technology, Halsted Press, Chicester, 1989. 2 J.L. Bolland and G. Gee, Trans. Farad. Soc., 42 (1946) 236. 3 W.O. Drake, Hindered amine stabilisers as thermal stabilisers or HAS as HATS not just HALS, Proceedings of the 14th International Stability Controlled Degradation, Luzern, Switzerland, 1992, p. 57. 4 F. Gugumus, Polym. Degrad. Stab., 40 (1993) 167. 5 P. Nesvadba, S. Evans, R. Schmitt, US 5, 607, 624. 6 P. Nesvadba, L. Bugnon, P. Dubs and S. Evans, Synlett, (1999) 863. 7 J. Verdu, J. Rychly´ and L. Audouin, Polym. Degrad. Stab., 79 (2003) 503. 8 P. Sˇimon, M. Veverka and J. Okuliar, J. Pharmaceuticals, 270 (2004) 21. 9 V.Ya. Shlyapintokh, O.N. Karpukhin, L.M. Postnikov, I.V. Zakharov, A.A. Vichutinskii and V.F. Tsepalov, Chemiluminescence Methods of Investigation of Slow Chemical Processes (in Russian), Publishing House Nauka, Moscow, 1966. 10 G.E. Ashby, J. Polym. Sci., 50 (1961) 99. 11 M.P. Schard and C.A. Russell, J. Appl. Polym. Sci., 8 (1964) 985. ibid., 8 (1964) 997. 12 L. Matisova´-Rychla´ and J. Rychly´, Inherent relations of chemiluminescence and thermooxidation of polymers, In: R.L. Clough, N.C. Billingham and K.T. Gillen (Eds.), Advances in Chemistry, Series 249: Polymer Durability, Degradation, Stabilization and Lifetime Prediction. American Chemical Society, Washington, DC, 1996, p. 175. 13 G. George and M. Celina, Homogeneous and heterogeneous oxidation of polypropylene. In: S. Halim Hamid and M. Dekker (Eds.), Handbook of Polymer Degradation, Second Ed., Inc., M. Dekker, New York, p. 277. 14 J. Rychly´ and L. Rychla´, Chemiluminescence from polymers. In: M. Strlicˇ and J. Kolar (Eds.), Ageing and Stabilisation of Paper, National and University Library, Ljubljana, Slovenia, 2005, p. 71. 15 K. Jacobsson, P. Eriksson, T. Reitberger, B. Stenberg, Chemiluminescence as a tool for polyolefin oxidation studies, In: A.C. Albertsson (Ed.), Long Term Properties of Polyolefins, Advances in Polymer Science, Springer, 2004, Vol. 169, p. 151. 16 L. Rychla´ and J. Rychly´, New concepts in chemiluminescence at the evaluation of thermooxidative stability of polypropylene from isothermal and non-isothermal experiments. In: A. Jimenez and G.E. Zaikov (Eds.), Polymer Analysis and Degradation, Nova Science Publishers, New York, 2000 p. 124. 17 L. Zlatkevich, Luminescence Techniques in Solid State Polymer Research, M. Dekker, New York, 1989, Chapter 7.
Role of Oxidation in Degradation of Polymers
18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54
55 56 57 58 59 60 61 62 63 64 65 66
497
N.C. Billingham, E.T.H. Then and P. Gijsman, Polym. Degrad. Stab., 34 (1991) 263. E. Lengfelder, E. Cadenas and H. Sies, FEBS Lett., 164 (1983) 366. O.V. Reshetnyak, E.P. Kovalchuk, P. Skurski, J. Rak and J. Blazejowski, J. Lumin., 105 (2000) 27. E.M.Y. Quinga and D.G. Mendenhall, J. Am. Chem. Soc., 105 (1983) 6520. L. Audouin-Jirackova and J. Verdu, J. Polym. Sci., 25 (1987) 1205. Z. Osawa, H. Kuroda and Y. Kobayashi, J. Appl. Polym. Sci., 29 (1984) 2843. I. Blakey and G.A. George, Macromolecules, 34 (2001) 1873. R.E. Kelogg, J. Am. Chem. Soc., 91 (1969) 5433. F. Gugumus, Polym. Degrad. Stab., 77 (2002) 147. R. Broska, J. Rychly´ and L. Matisova´-Rychla´, Europ. Polym. J., 32 (1996) 1251. V.V. Ptschelintsev and E.T. Denisov, Vysokomol. Soed. (in Russian), 27 (1985) 1123, 1136. J. Rychly´, M. Strlicˇ, L. Matisova´-Rychla´ and J. Kolar, Polym. Degrad. Stab., 73 (2002) 357. L. Matisova´-Rychla´ and J. Rychly´, Polym. Degrad. Stab., 67 (2000) 515. A.M. Wynn and W.W. Wendlandt, Thermochim. Acta, 13 (1975) 393. W.W. Wendlandt, Thermochim. Acta, 68 (1983) 383. W.W. Wendlandt, Thermochim. Acta, 68 (1983) 387. W.W. Wendlandt, Thermochim. Acta, 71 (1983) 129. W.W. Wendlandt, Thermochim. Acta, 72 (1984) 363. W.W. Wendlandt and M. Kasper, Thermochim. Acta, 75 (1984) 249. C.H. Hsueh and W.W. Wendlandt, Thermochim. Acta, 99 (1986) 43. C.H. Hsueh and W.W. Wendlandt, Thermochim. Acta, 99 (1986) 37. M. Strlicˇ, J. Kolar, B. Pihlar, J. Rychly´ and L. Matisova´-Rychla´, Eur. Polym. J., 36 (2000) 2351. G.D. Mendenhall and H.L. Agarwal, J. Appl. Polym. Sci., 33 (1987) 1259. G.J. Sewell, N.C. Billingham, K.A. Kozielski and G.A. George, Polymer, 41 (2000) 2113. I. Blakey, Thesis: Aspects of oxidative degradation of polypropylene, Queensland University of Technology, Brisbane, Australia, 2001. L. Rosı´k, Ageing and stabilization of elastomers. In: J. Pech (Ed.), Synthetic Rubber, SNTL, Praha, Praha (in Czech), 1971, p. 411. H. Mori, T. Hatanaka and M. Terano, Macromol. Rapid Commun., 18 (1997) 157. Z. Osawa, M. Kato and M. Terano, Macromol. Rapid Commun., 18 (1997) 667. M. Kato and Z. Osawa, Polym. Degrad. Stab., 65 (1999) 457. M. Iring, Zs. Laszlo-Hedvig, F. Tudos and T. Kelen, Polym. Degrad. Stab., 467 (1983) 5. J. Rychly´, L. Matisova´-Rychla´, P. Tiemblo and J. Gomez-Elvira, Polym. Degrad. Stab., 71 (2001) 253. P. Gijsman and F. Verdun, Polym. Degrad. Stab., 74 (2001) 533. P. Gijsman, J. Hennekens and J. Vincent, Polym. Degrad. Stab., 42 (1993) 95. R.J.C.W. Chien and H. Jabloner, J. Polym. Sci. A-1, 6 (1968) 393. R.J.C.W. Chien and C.R. Boss, J. Polym. Sci. A-1, 5 (1967) 3091. N.C. Billingham, G.A. George, J. Polym. Sci., Part B, Polym. Phys. Ed., 28 (1990) 257. G.A. George, Use of chemiluminescence to study the kinetics of oxidation of solid polymers. In: N. Grassie (Ed.), Developments in Polymer Degradation-3, Applied Science Publishers, London, 1981, p. 173. V. Dudler, D.J. Lacey and Ch. Krohnke, Polym. Degrad. Stab., 51 (1996) 115. M. Celina, G.A. George, D.J. Lacey and N.C. Billingham, Polym. Degrad. Stab., 47 (1995) 311. L. Matisova´-Rychla´ and J. Rychly´, Polym. Degrad. Stab., 73 (2001) 393. P. Eriksson, T. Reitberger, G. Ahlblad and B. Stenberg, Polym. Degrad. Stab., 73 (2001) 177. B.G.S. Goss, M.D. Barry, D. Birtwhistle and G.A. George, Polym. Degrad. Stab., 74 (2001) 271. B.G.S. Goss, I. Blakey, M.D. Barry and G.A. George, Polym. Degrad. Stab., 74 (2001) 523. D.R. Kohler and C. Krohnke, Polym. Degrad. Stab., 63 (1999) 165. D.R. Kohler and C. Krohnke, Polym. Degrad. Stab., 62 (1998) 385. S. Jipa, R. Setnescu, T. Setnescu, C. Cazac, P. Budrugeac and I. Mihalcea, Polym. Degrad. Stab., 40 (1993) 101. L. Zlatkevich, J. Polym. Sci., Part B, Polym. Phys. Ed., 23 (1985) 2633. F. Gugumus, Polym. Degrad. Stab., 63 (1991) 41. H. Zweifel, Stabilization of Polymeric Materials, Springer, Berlin, Heidelberg, 1998.
498
Jozef Rychly´ and Lyda Matisova´-Rychla´
67 L. Audouin, V. Langlois and J. Verdu, In: Patsis (Ed.), 16th International Conference on Advances in the Stabilization and Degradation of Polymers, Luzern, 1994, p. 11. 68 L. Audouin, V. Gueguen, A. Tcharkhtchi and J. Verdu, J. Polym. Sci., Polym. Chem. Ed., 33 (1995) 921. 69 M. Pletenı´kova´, L. Matisova´-Rychla´, J. Rychly´ and I. Lacı´k, Carbohydr. Polym., 69 (2007) 50. 70 J. Rychly´, L. Matisova´-Rychla´, V. Bukovsky´, M. Pletenı´kova´ and M. Vrsˇka, Macromol. Symposia, 231 (2006) 178. 71 N.C. Billingham, E.S. O’Keefe and E.T.H. Then, Polym. Mater. Sci. Eng., 58 (1988) 431. 72 K.R. Kopecky, J.E. Filbz, C. Mumford, P.A. Lockwood and J.-Y. Ding, Can. J. Chem., 53 (1983) 1103.
CHAPT ER
12 ESR and ESR Imaging Methods for the Study of Oxidative Polymer Degradation Shulamith Schlick and Krzysztof Krucza"a
Contents
1. Introduction: Polymer Degradation in the Presence of Oxygen 1.1 The degradation cascade 1.2 Spatial dependence of degradation processes 1.3 Polymer stabilization by hindered amines 2. Fundamentals of ESR and ESR Imaging 2.1 Basic principles of ESR 2.2 Anisotropic g- and hyperfine tensors 2.3 Isotropic hyperfine analysis 2.4 ESR spectra of nitroxide radicals 2.5 Spin trapping 2.6 ESR imaging 3. ESR as a Tool for the Study of Polymer Degradation 3.1 Direct ESR detection of radicals formed during degradation 3.2 Spin trapping of short-lived radical species formed during polymer degradation 4. ESR Imaging: A Nondestructive Method for Spatially Resolved Polymer Degradation 4.1 ESR imaging of polymers stabilized by hindered amines 4.2 1D and 2D spectral–spatial ESRI in heterophasic polymers 5. Concluding Remarks Acknowledgements References
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00412-1
500 500 501 503 504 504 506 506 507 507 510 513 513 516 517 517 517 521 521 522
r 2008 Elsevier B.V. All rights reserved.
499
500
Shulamith Schlick and Krzysztof Krucza"a
1. INTRODUCTION: POLYMER DEGRADATION IN THE PRESENCE OF OXYGEN 1.1 The degradation cascade In the presence of oxygen, polymers undergo degradation when exposed to environmental factors such as heat, ionizing or UV irradiation, nitrogen oxides and other pollutants, and physical stresses. The degradation process usually starts with the formation of polymer-derived free radicals, R , peroxides, ROO , and hydroperoxides ROOH, as shown schematically in Figure 1 [1–4], (see also previous chapter). Reactions triggered by these reactive intermediates can lead to profound changes in polymer properties, on both the molecular and macroscopic levels. The chemical structure is modified due, for example, to chain unzipping and cross-linking, leading to changes of the elastic properties and of the degree of crystallinity [1]. Small amounts of chromophores, free radicals, and metallic residues from polymerization reactions can introduce additional reaction pathways that usually increase the rate of degradation. The basic autoxidation scheme (BAS) [5,6] as well as the closed-loop kinetic scheme (CLS) [7] have been proposed, and widely discussed in the literature, in order to determine the kinetics of degradation processes, and assess the effects of the radical structure and concentration. Accelerated degradation at high treatment temperatures or upon UV irradiation is often performed in the laboratory, and the results are interpreted in terms of polymer lifetimes in actual applications [8,9]. Electron spin resonance (ESR) methods have been extensively used to detect and identify the radicals formed during degradation, to clarify the mechanism, and to simulate the variation of the ESR spectra with treatment conditions, and in the presence or absence of chromophores, antioxidants, and other stabilizers. The method is based on the exceptional sensitivity and specificity of ESR for the detection and identification of species with unpaired electron spins; these species can be organic and inorganic radicals, triplet states, and complexes of paramagnetic ions. In many systems, the reactive radicals are short-lived, and can be detected only at low temperatures, or by gradual annealing to higher temperatures. ESR spectroscopy is also important for determining the stability of various radicals and their transformation to other species. O2
Polymer (RH)
.
ROO
RH .
.
.
RO + OH
R
O2 hν heat
RH
ROOH Heat Metal cations
Structure Modifications
Figure 1 Schematic description of polymer degradation in the presence of oxygen.
ESR and ESR Imaging Methods
501
When the lifetime of the radicals is very short and direct ESR detection is not an option, spin trapping is used to detect radicals at ambient temperatures. The method is based on the scavenging of radicals, P, by a spin trap, leading to the formation of a spin adduct with higher stability; in most cases, this adduct is a nitroxide radical.
1.2 Spatial dependence of degradation processes Degradation processes involve complex heterogeneous reactions that can occur at the polymer sample surface, or inside the polymer; the rate of these processes depends on the rate of oxygen diffusion and on the rates of formation of unstable intermediates. At low degradation rates, the oxygen consumption is lower than the amount provided by diffusion, and oxidation occurs through the entire sample. However, when the rate of oxygen consumption in chemical reactions is higher than its supply rate, mainly the surface layers are oxidized; this is the diffusion-limited oxidation (DLO) regime [10–12]. The DLO concept implies that in order to understand degradation and predict lifetimes of polymeric materials undergoing treatment in different environments, it is necessary to develop profiling methods that determine the spatial variation of the extent of degradation, within the sample depth. During oxidative polymer degradation, the distribution of oxygen in the polymer with depth, x, can be described by Equation (1) [13,14] 2 @½O2 @ ½O2 ¼D (1) k½O2 @t @x2 where the two terms on the right describe respectively the rate of oxygen diffusion, and the rate of oxygen consumption due to degradation, assuming a first-order reaction. In Equation (1), k is the rate constant for oxygen consumption during polymer aging, and D is the diffusion coefficient of oxygen. For steadystate conditions, the rate of oxygen consumption is equal to the oxygen supply by diffusion, Equation (2). 2 @ ½O2 D (2) ¼ k½O2 @2 x For the boundary conditions ½O2 ¼ ½O2 0 at x ¼ 0 and @½O2 =@x ¼ 0 at x ¼ l, the solution of Equation (2) is (where l is the sample depth) ½O2 ¼
½O2 0 cosh½ðk=DÞ1=2 ðl xÞ cosh½ðk=DÞ1=2 l
(3)
Assuming that all available oxygen in the polymer is reacting, and that the oxygen-containing products are not lost by diffusion, Equation (3) describes the distribution of oxygen-containing products such as hydroxyl, carbonyl, and nitroxyl. For large values of x, Equation (3) can be approximated as in Equation (4) " # C k 1=2 ¼ exp x (4) C0 D
502
Shulamith Schlick and Krzysztof Krucza"a
where C0 and C are the concentrations of oxidation products on the surface and at depth x, respectively. The parameter a ¼ (D/k)1/2, known in the literature as the degradation depth, shows the depth where most (90%) of oxygen-containing products are located and can be deduced by plotting ln(C/C0) as a function of x, if the concentration profiles of degradation products are determined by experiment. As will be seen below, such information can be deduced from ESR imaging (ESRI) experiments [14]. For the same D value, the degradation depth is expected to be lower for more advanced degradation. Theoretical concentration profiles, calculated from Equation (4), are shown for different degradation depth, a, in Figure 2. Homogeneous degradation is expected when a ¼ 3 mm, close to the sample thickness; for lower values of a, the degradation becomes progressively more heterogeneous, and is highly heterogeneous for a ¼ 0.1 mm, much lower than the sample thickness (the DLO regime). In the case of spatially heterogeneous degradation, the lifetimes of polymeric materials deduced from the study of average properties cannot be used to estimate the durability of polymers in normal use. For this reason, methods for describing the spatial distribution of polymeric properties due to degradation have been developed. One of these methods is ESRI, a technique that will be described and discussed in this chapter. As ESRI is based on the presence of a paramagnetic species that provides the contrast in the imaging experiments, we will now discuss the hindered amine stabilizers (HAS) that are used to reduce the degradation rate of polymers [15]. The stabilization process is based on the formation of nitroxides from HAS (‘‘HAS–NO’’) during polymer degradation; these nitroxides scavenge the reactive radicals formed during degradation, and, in addition, make possible the ESRI experiments.
Figure 2 Relative concentration profiles of oxidation products during thermal degradation as a function of depth for a plaque with thickness 3 mm: Nearly homogeneous profile when the degradation depth, a, is 3.0 mm, similar to sample thickness, and heterogeneous profile when the degradation depth, a, is 0.1 mm, smaller than the sample thickness. The profiles were calculated from Equation (4).
ESR and ESR Imaging Methods
503
1.3 Polymer stabilization by hindered amines The polymer degradation scheme discussed above and shown in Figure 1 is valid in polymers without any additives. However, most commercially available materials are doped with UV absorbers and with light and thermal stabilizers in order to extend their lifetime. The HAS rank among the most important additives used for light and heat stabilization of polymers [9,15,16]. Most commercially available HAS stabilizers are 4-substituted 2,2,6,6-tetramethylpiperidines, as shown below [17].
Figure 3 presents some of the chemical processes involving HAS during polymer exposure to radiation and oxygen [15,17]. The HAS-derived nitroxides are thermally stable, but can react with free radicals (as scavengers) to yield diamagnetic species; the hydroxylamines can regenerate the original amine, thus resulting in an efficient protective effect (see also Chapter 3). The remainder of this chapter is organized as follows: The fundamentals of ESR spectroscopy are described in Section 2, with emphasis on the R
NH
hν ROO
N
O2
NO
NOR
ROOH ROOR
Figure 3 The chemistry of a hindered amine stabilizer (HAS).
ROO
504
Shulamith Schlick and Krzysztof Krucza"a
experimentally available parameters relevant for polymeric systems. Also included in Section 2 are direct ESR and spin-trapping experiments, and a brief description of the transition from ESR spectroscopy to ESRI. Applications of ESR spectroscopy (direct ESR and spin trapping) to polymer degradation are described in Section 3. The ability to study spatially resolved polymer degradation via ESRI is described in Section 4. We will conclude with an evaluation of the strengths of ESR methods in Section 5.
2. FUNDAMENTALS OF ESR AND ESR IMAGING ESR is a spectroscopic technique that detects the transitions induced by electromagnetic radiation between the energy levels of electron spins in the presence of a static magnetic field. The method can be applied to the study of species containing one or more unpaired electron spins; examples include organic and inorganic radicals, triplet states, and complexes of paramagnetic ions. Spectral features such as resonance frequencies, splittings, line shapes, and line widths are sensitive to the electronic distribution, molecular orientation, nature of the environment, and molecular motion. Theoretical and experimental aspects of ESR have been covered in a number of books [18–25] and reviewed periodically [26–28]. ESR fundamentals and applications to polymeric systems have been described [29–33]. In this section we will describe the fundamentals of ESR, the method of spin trapping, and the basics of ESR imaging. ESR fundamentals with emphasis on applications to polymeric systems have been described elsewhere [30–33].
2.1 Basic principles of ESR The Hamiltonian energy operator Hspin for an electron spin is given by Equation (5a)1 Hspin ¼ ge be S H
(5a)
where S is the spin angular momentum, H the magnetic field vector in gauss (G) or tesla (1T ¼ 104 G), be the Bohr magneton equal to 9.274 1021 ergG1 (or 9.274 1024 JT1), and ge (equal to 2.0023 for a free electron) is the g factor or spectroscopic splitting factor (dimensionless). This spin Hamiltonian operates only on the spin wave functions a and b, whose spin angular momenta are +1/2 and 1/2, respectively, in units of h/2p; h is the Planck constant. For a magnetic field oriented along the z direction, Equation (5a) becomes Hspin ¼ ge be Sz H
(5b)
The energy difference between the two levels is DE ¼ hu ¼ gebeH. Typically ESR is carried out in a magnetic field of about 3500 G or 0.35 T. The corresponding 1
Operators, vectors, and tensors are written in bold.
ESR and ESR Imaging Methods
505
absorption frequency, u, is E9.5 GHz, in the microwave frequency range known as X band. ESR measurements at other frequencies are also carried out [31–33], but are not covered in this section, since the X band is the most commonly used in the materials science. Moreover, most rules and conclusions are also valid for other bands. The real power of ESR spectroscopy for identification of radical structure is based on the interaction of the unpaired electron spin with nuclear spins. This interaction splits the energy levels and often allows determination of the atomic or molecular structure of species containing unpaired electrons. The more complete Hamiltonian is given in Equation (6) for a species containing one unpaired electron, where the summations are over all the nuclei, n, interacting with the electron spin. X X Hspin ¼ be H ge S gn bn H I n þ h S An I n X (6) þh I n Qn I n In Equation (6) ge is the electronic g tensor, gn is the nuclear g factor (dimensionless), bn is the nuclear magneton in erg/G (or J/T), In is the nuclear spin angular momentum operator, An is the electron–nuclear hyperfine tensor in Hz, and Qn (non-zero for InX1) is the quadrupole interaction tensor in Hz. The first two terms in the Hamiltonian are the electron and nuclear Zeeman interactions, respectively; the third term is the electron–nuclear hyperfine interaction; and the last term is the nuclear quadrupole interaction. For the usual systems with an odd number of unpaired electrons, the transition moment is finite only for a magnetic dipole moment operator oriented perpendicular to the static magnetic field direction. In an ESR resonator in which the sample is placed, the microwave magnetic field must be therefore perpendicular to the external static magnetic field. The selection rules for the electron spin transitions are given in Equation (7) DmS ¼ 1 and
DmI ¼ 0
(7)
where mS and mI refer to the electron and nuclear spin quantum numbers, respectively. Transitions correspond therefore to a change in the electron spin orientation, and a fixed nuclear spin orientation. The energy difference between two adjacent transitions associated with the same type of nucleus is defined as the hyperfine constant, usually symbolized by A in frequency units (MHz) or in Gauss when the g value is E2. Since DmI ¼ 0, the effect of the nuclear Zeeman term (second term on the right side of Equation (6)) and of the nuclear quadrupole term (last term on the right side of Equation (6)) in the spin Hamiltonian cancel out to first order. In the solid state the selection rules are not strictly obeyed when the hyperfine coupling and nuclear Zeeman interaction are of the same order of magnitude. Forbidden transitions with DmS ¼ 71 and DmI ¼ 71 then have a finite transition probability and can be used for measuring nuclear frequencies by time-domain techniques. In this situation ESR line shapes are slightly influenced by the nuclear Zeeman and nuclear quadrupole interactions.
506
Shulamith Schlick and Krzysztof Krucza"a
2.2 Anisotropic g- and hyperfine tensors The hyperfine tensor A for each nucleus is a real 3 3 matrix that can always be diagonalized. The components of the diagonalized hyperfine tensor consist of an isotropic part, ao, and a purely anisotropic part, au, whose orientational average is zero. Thus, the au components are averaged out in fluid media and can be determined only in the solid state or in the case of highly restricted molecular motion. The diagonal elements of a diagonalized hyperfine tensor are called the principal values. The complete hyperfine tensor (including anisotropic and isotropic contributions) is determined from single crystal spectra, or by analysis of ESR spectra in disordered (‘‘powder’’) samples, which consist of a superposition of all possible orientations. The physical interpretation of the anisotropic principal values is based on the classical magnetic dipole interaction between the electron and nuclear spin angular momenta, and depends on the electron–nuclear distance, rn. Assuming that both spins can be described as point dipoles, the interaction energy is given by Equation (8), where y is the angle between the external magnetic field and the direction of rn. ð1 3 cos2 yÞ Hspin ðanisoÞ ¼ ge be gn bn IS (8) r3n Thus, for the general case of a delocalized electron spin, the anisotropic hyperfine components depend upon the orientation-weighted spatial average of r3 n over the electronic orbital of the unpaired electron in a paramagnetic species. The number of spectral lines associated with a given interacting nucleus is 2In + 1 and the lines are of equal intensity. Often an anisotropic hyperfine interaction is accompanied by g anisotropy, and the components of the g tensor can be determined in a similar way, from ESR spectra measured in single crystals or disordered systems. Single crystal studies also allow the determination of the orientation between the principal directions of the g- and hyperfine tensors and the crystal symmetry axes. Analysis of the complete anisotropy allows the determination of the x, y, and z components of the g- and A tensors.
2.3 Isotropic hyperfine analysis The special case of isotropic g and hyperfine interaction will now be considered. This simplification is valid when the anisotropic interactions are averaged by rapid tumbling. The quadrupole interaction will be omitted because it is purely anisotropic. The resulting simplified spin Hamiltonian is given in Equation (9). X X Hspin ðisoÞ ¼ ge be H S gn bn H I n þ h An S I n (9) In some systems, when an anisotropic spectrum is detected at low temperatures, increasing the temperature leads to averaging of the principal components of the hyperfine and g tensors, and therefore to isotropic spectra. This is often the situation in polymer systems at temperature above the glass transition temperature, Tg.
ESR and ESR Imaging Methods
507
2.4 ESR spectra of nitroxide radicals Nitroxide radicals, mixed in polymers (as ‘‘spin probes’’), or chemically bonded to polymer segments (as ‘‘spin labels’’) are useful as reporters for the determination of chain dynamics, rotational correlation time, tc, and local polarity [34–37]. In HAS-doped polymers, these radicals make possible the ESRI experiments. The ESR spectra of these radicals can be understood by examination of Figure 4. Figure 4a shows the molecular axes system in nitroxides, and Figure 4b shows the corresponding ESR spectra when nitroxides in single crystals are oriented with their x, y, and z axes, respectively, parallel to the external magnetic field. The motionally narrowed ESR spectrum of a nitroxide radical, usually observed in liquid polymer solutions or in polymers above Tg and corresponding to tco10 ps, consists of three equally spaced signals separated by E16 G due to hyperfine splitting of 14N nuclei (aN ¼ 16 G), as shown in the top trace of Figure 4c. The separation between the outer extrema of the spectrum in this limit is E 32 G. A dramatically different spectrum is observed in the rigid limit, as shown in the lower trace in Figure 4c, which corresponds to tcW1 ms; the extreme separation measured in the powder spectrum becomes 2AzzE70 G, depending on the local polarity. In polymeric materials the rigid limit can be obtained at ambient temperatures if the polymer is below the glass transition temperature, Tg; otherwise the sample must be cooled. The dynamics of spin probes in polymers is often characterized by T50G, the temperature for which the extreme separation is 50 G [38,39]. Below T50G, the nitroxide is in the slow-tumbling regime and the spectra are anisotropic; above T50G, the motionally narrowed regime is reached. The relation between T50G (measured by ESR) and Tg (e.g., measured by differential scanning calorimetry (DSC)) depends, however, on the type of spin probe or label and its interaction with the polymer matrix. In microphase-separated systems, ESR spectra may consist of a superposition of two contributions, from nitroxides in both fast and slow-tumbling regimes. Such spectra provide evidence for the presence of two types of domains with different dynamics and transition temperatures. This case was detected for a HAS-derived nitroxide radical in heterophasic poly(acrylonitrile-butadienestyrene) (ABS); as shown in Figure 5, the fast and slow components in the ESR spectrum measured represent nitroxide radicals located in butadiene-rich (B-rich) and styrene/acrylonitrile-rich (SAN-rich) domains, respectively [40]. These two components were determined by deconvoluting the ESR spectrum of HAS–NO measured at 300 K.
2.5 Spin trapping Since its discovery in the late 1960s [41,42], the method of spin trapping has been extensively used for the detection and identification of short-lived free radicals in chemistry, biology, and medicine studies [41–50]. The method is based on the scavenging of radicals, P , by a spin trap, leading to the formation of a spin adduct with higher stability, typically a nitroxide radical. Nitroso and
508
Shulamith Schlick and Krzysztof Krucza"a
(a)
(b)
(c) Motionally Averaged
32 G Rigid Limit
70 G
3300
3320
3340 3360 3380 Magnetic Field / G
3400
Figure 4 ESR of nitroxide radicals: (a) Molecular axes of the nitroxide; (b) ESR spectra of oriented nitroxide radicals, with the molecular axes x, y, and z along the external magnetic field, respectively; and (c) ESR spectra of randomly oriented nitroxide radicals: motionally averaged (upper) and rigid limit (lower) regimes.
ESR and ESR Imaging Methods
509
"Slow" (SAN-rich Phase)
"Fast" (B-rich Phase)
3300
3320
3340 3360 3380 Magnetic Field / G
3400
3420
Figure 5 Dynamically slow and fast ESR spectra of HAS–NO at 300 K from the SAN-rich and B-rich regions of ABS, respectively.
nitrone compounds are the most commonly used spin traps, and are shown below.
The process of trapping and adduct formation is shown below for a nitrone spin trap. H
H R C N R′ + O Nitrone spin trap
.
P
R C N R′ P O. Spin adduct
510
Shulamith Schlick and Krzysztof Krucza"a
In most cases the ESR spectra of spin adducts exhibit hyperfine splittings (hfs) from the 14N and Hb nuclei. The goal in spin-trapping experiments is to translate these splittings into an identity of the trapped radical P. Normally it is easy to establish the presence of the radical, and more of a challenge to identify it. The stability of the spin trap under conditions necessary for the formation of radicals is an important consideration. Careful sample preparation, the collection of splittings from a given system in a series of media and as a function of pH and temperature, and isotopic enrichment by 2H, 13C, 15N, and 17O have been used for positive identification. The spin-trapping database is a useful resource [51]. a-Phenyl-tert-butylnitrone (PBN) is a useful spin trap that has the advantage of its stability under UV irradiation and its selectivity towards trapping of carbon-centered radical species; this advantage is, however, offset by the lack of specificity in the hfs of the spin adduct [44,45]. Spin trapping by 5,5-dimethylpyrroline-N-oxide (DMPO) has emerged as an important method for the identification of unstable intermediates, because the splittings from the Hb protons are sensitive to the nature of the trapped radical; moreover, in some cases splittings from Hg protons can also be resolved. The use of DMPO as a spin trap has been described in many studies [44–50], aimed at the detection of oxygen radicals such as OH, OOH, and O2, as well as carbon-centered radicals. The clear distinction between these two groups of free radical adducts is based on the large difference in the Hb proton splittings: typically 10–15 G for oxygen radicals, and W20 G for carbon-centered radical adducts. 2-Methyl-2-nitrosopropane (MNP) as a spin trap is often advantageous, because splitting from the trapped radical can be recognized directly [52].
2.6 ESR imaging ESR spectroscopy can be transformed into an imaging method, ESRI, for samples containing unpaired electron spins, if the spectra are measured in the presence of magnetic field gradients. In an ESRI experiment the microwave power is absorbed by the unpaired electrons located at point x when the resonance condition, Equation (10), is fulfilled. gbe n¼ (10) ðH res þ xGx Þ h In Equation (10), Gx is the linear magnetic field gradient (in G/cm) at x. As in nuclear magnetic resonance imaging (NMRI or MRI), the field gradients produce a correspondence between the location x and the resonant magnetic field, Hres, and allow encoding of spatial information in the ESR spectra. If the sample consists of two point samples, for example, the distance between the samples along the gradient direction can be deduced if the field gradient is known [53]. The spatial resolution, Dx, is an important parameter in imaging, and can be defined in various ways, as discussed recently [54]; the resolution depends on the line width and line shape. Most commonly Dx is expressed as the ratio of the line width to the field gradient, DH/Gx; this definition implies that two signals
ESR and ESR Imaging Methods
511
separated by one line width due to the field gradient can be resolved. The typical resolution in our ESRI experiments is E 100 mm. An ESRI system can be built with small modifications of commercial spectrometers by, for example, gradient coils fixed on the poles of the spectrometer magnet, regulated direct current (DC) power supplies, and required computer connections [40,53,55]. Gradients can be applied in the three spatial dimensions, and a spectral dimension can be added by the method of stepped gradients. The spectral dimension is important when the spatial variation of ESR line shapes (as a function of sample depth) is of interest; this situation will be described below, in the ESRI studies of heterophasic polymers. In most systems, the software for image reconstruction in ESRI experiments must be developed in-house. We will describe below 1D spatial and 2D spectral–spatial ESRI experiments, which have been used in several laboratories, including ours, for the study of polymer degradation.
2.6.1 1D ESR imaging In the general case, the sample contains a distribution of paramagnetic centers along a given direction, for example x. The ESR spectrum in the presence of the magnetic field gradient (the ‘‘1D image’’) is a superposition of signals from paramagnetic centers located at different positions. Figure 6 shows the ESR spectrum of a nitroxide radical in the absence of the field gradient in (a), in the presence of the gradient for a homogenous distribution of the nitroxide in (b), and in the presence of the gradient when the radicals are present only in thin layers at both surfaces of the polymer plaque in (c).
(a)
(b)
(c)
3300
3350 Magnetic Field / G
3400
Figure 6 Simulated ESR spectra of nitroxides: (a) in the absence of magnetic field gradient; (b) 1D image for a homogenous radical distribution (in the presence of a gradient); and (c) 1D image for radicals present only in thin layers near both surfaces of the plaque (in the presence of a gradient).
512
Shulamith Schlick and Krzysztof Krucza"a
Mathematically, the 1D image is a convolution of the regular ESR spectrum with the distribution function of the paramagnetic centers; the radical distribution (‘‘intensity profile’’) is obtained by deconvolution. Various optimization methods for the intensity profile have been used. In our initial ESRI studies, the concentration profiles of the radicals were deduced by Fourier transform followed by optimization with the Monte Carlo (MC) procedure [56–58]. The disadvantage of this method is the high-frequency noise present in the optimized profiles. In more recent publications, the intensity profile was fitted by analytical functions and convoluted with the ESR spectrum measured in the absence of the field gradient in order to simulate the 1D image. The best fit was obtained by variation of the type and parameters of the analytical functions chosen (e.g., Gauss or Boltzmann) in order to obtain good agreement with the 1D image, and selected by visual inspection [59,60]. Lately the genetic algorithm (GA) for minimization of the difference between simulated and experimental 1D images was implemented; this procedure allowed the best fit to be chosen automatically [61]. A typical GA consists of creating the initial population, calculating the fit to experimental data, selecting the couples, crossover (reproduction) and mutation. The approach and terminology are adopted from biology and resemble fundamental steps in evolution.
2.6.2 2D spectral–spatial ESR imaging Each 2D image is reconstructed from a complete set of projections, collected as a function of the magnetic field gradient, using a convoluted back-projection algorithm [62]. The number of points for each projection (1024) is kept constant. The maximum experimentally accessible projection angle, amax, depends on the maximum gradient Gmax according to tanamax ¼ (L/DH) Gmax, where L is the sample length, and DH the spectral width. The maximum sweep width is SWmax ¼ O2DH/cosamax. For a width DHE65 G (which is typical for the slowmotional spectral component of a nitroxide radical present in aged polymers), a sample length of 4 mm, and a maximum field gradient of 250 G/cm along the vertical axis, amax ¼ 571 and SWmax ¼ 169 G. A complete set of data for one image consists of 64–128 projections, taken for gradients corresponding to equally spaced increments of a in the range 901 to +901; of these projections, typically 41 or 43 projections (out of 64) are experimentally accessible and the rest are projections at missing angles (for a in the intervals 601–901, and from 601 to 901). The projections at the missing angles can be assumed to be the same as those at the maximum experimentally accessible angle amax, or determined by the projection slice algorithm (PSA) with several iterations [60–62]. To illustrate the potential of the method, we present in Figure 7 the 2D ESRI perspective plot of a phantom sample consisting of nitroxide biradicals derived from Tinuvins 770 (obtained by oxidation of the amine) in two different environments in a plaque of heterophasic propylene–ethylene copolymers (HPEC). One side of the plaque was doped with the biradical by contact with a biradical solution in toluene. The same biradical solution was placed on transparent tape and the solvent was evaporated; the tape was then folded and attached to the other side of the plaque. The corresponding spectral slices are
ESR and ESR Imaging Methods
513
Figure 7 (a) 2D spectral–spatial perspective plot of nitroxide biradicals derived from HAS doped in HPEC on one side of the plaque (left), and in a transparent film attached to the plaque on the opposite side (right). (b) Spectral slices determined nondestructively from 2D plot: ESR spectra of biradicals located in two amorphous phases in the polymer (upper), and dispersed in a film (bottom).
presented in the derivative mode on the right side of the figure. The upper spectrum in Figure 7b, obtained from the polymer doped with the biradical, consists of two components, and was interpreted in terms of radicals dispersed in two different amorphous phases [61]: the broader signal represents radicals dispersed in the rigid amorphous phase, and the sharper signal is due to nitroxides located in amorphous domains. We note that the Tg of the rigid amorphous phase is higher than that of the amorphous phase. The bottom spectrum in Figure 7b consists of only one signal, typical for nitroxide radicals in a medium that allows rapid dynamics. 2D spectral–spatial ESRI thus allows visualization of the variation of the ESR spectra as a function of sample depth.
3. ESR AS A TOOL FOR THE STUDY OF POLYMER DEGRADATION In this section we will illustrate the application of ESR methods in order to detect and identify polymer fragments, reactive intermediates, as well as reactive oxygen species that attack the polymer structure. Some examples are selected from studies of polymer degradation performed at the University of Detroit Mercy laboratory.
3.1 Direct ESR detection of radicals formed during degradation Radicals can be detected by direct ESR if their concentration is stable and high enough during spectra acquisition. This condition is often fulfilled in the case of
514
Shulamith Schlick and Krzysztof Krucza"a
polymer-derived radicals produced in fluorinated polymers by high-energy irradiation, because some perfluoroalkyl radicals can be stabilized even at ambient temperature. In these experiments, irradiation in vacuum has enabled the study of the type and mobility of alkyl radicals derived from the polymer. Admission of oxygen usually led to the formation of the corresponding peroxy radicals, ROO . This transformation can be followed by ESR because peroxy radicals have a more anisotropic g tensor, and the principal values are higher compared to those of alkyl radicals; in addition, microwave power saturation experiments have been used to separate alkyl and peroxy radicals, because the signals from the alkyl radicals are easier to saturate. Hara et al. have detected relatively stable radicals formed in g-irradiated cross-linked and non-cross-linked polytetrafluoroethylene (PTFE), and identified main-chain and chain-end perfluorinated alkyl radicals [63]. Radicals produced in poly(vinylidene fluoride) (PVDF) bombarded by electrons and protons were tracked by ESR spectroscopy [64], and the variation of the signal intensity with irradiation dose and the signal decay as a function of temperature were investigated. The spectrum was interpreted in terms of contributions from five radicals: —C H2, —C F2, —CH2C FCH2—, —CF2C HCF2—, and —CH2(CF ¼ CH)nC FCH2—. The relative intensity of each component depended on the irradiation dose. The concentration of radicals increased with dose in a similar way for electron and proton irradiation. The chemistry of radicals in irradiated fluorinated polymers has been described in detail in a comprehensive review [65]. Simulation programs for the ESR line shapes of peroxy radicals for specific models of dynamics have been developed for the study of oxidative degradation of polymers due to ionizing radiation [66]. The motional mechanism of the peroxy radicals, ROO , was deduced by simulation of the temperature dependence of the spectra, and a correlation between dynamics and reactivity has been established. In general, peroxy radicals at the chain ends are less stable and more reactive. This approach has been extended to protiated polymers, for instance polyethylene and polypropylene (PP) [67]. Radicals generated in conductive polymers such as polyacetylene (PA), polypyrrole (PPy), and polyaniline (PAn) were studied using direct ESR. Pfluger et al. [68] have investigated the influence of various gases on PPy oxidation and determined that oxidation leads initially to an ionic polymer, and is followed by reactions in which the nitrogen atoms in the pyrrole rings play the major role. Adachi and Yamauchi [69] have detected ESR spectra of UV-irradiated PPy. The samples were irradiated both in situ and ex situ with two high-pressure mercury lamps differing in their output, and the asymmetrical line shape (Dysonian) typical for conductive polymers was detected. The asymmetry and the line width increased with longer in situ irradiation time and returned to the starting values after the UV source was switched off; these changes were correlated with the higher polymer conductivity during irradiation. The authors concluded that UV irradiation generated dangling bonds (due to broken covalent bonds), polarons (a radical ion, S ¼ 1/2) and bipolarons (two re-united polarons, S ¼ 0), and finally led to polymer degradation in the case of strong irradiation.
ESR and ESR Imaging Methods
515
The in situ technique makes direct ESR detection possible even for short-lived radicals, since steady-state conditions can be reached and an adequate radical concentration can be sustained. Hasik et al. [70] have performed in situ catalytic tests in a reactor placed in the ESR resonator, with PAn doped with heteropolianion of the type H3PMo12O40 (Keggin units) as the catalyst. The catalytic activity of the system was tested for the conversion of ethyl alcohol to C2H4, (C2H5)2O, and CH3CHO as products. The experiments were performed as a function of temperature, and stabilization of the intermediates was achieved by lowering the sample temperature. During the experiment, line shape variation of the radical signal near g ¼ 2 was observed. The formation of stable carboncentered radicals in the conductive polymers (PAn, PPy, PA) after the hightemperature treatment, together with the catalytic reactions, were described in a series of papers [71,72]. After freezing the reaction system to 100 K, Mo(V) intermediates were detected, due to the reduction of Mo(VI) during the catalytic processes. These species were not observed in ex situ experiments. Ionomer membranes are used in fuel cells in order to separate the anode and cathode compartment and to allow the transport of protons from the anode to the cathode. The typical membrane is Nafions, which consists of a perfluorinated backbone and side chains terminated by sulfonic groups. In the oxidizing environment of fuel cells, Nafions, as well as other membranes, is attacked by reactive oxygen radicals, which reduce the membrane stability. Direct ESR was used recently in our laboratory to detect and identify oxygen radicals as well as radical intermediates formed in perfluorinated membranes upon exposure to oxygen radicals [73,74]. The three methods used to produce oxygen radicals in the laboratory and the corresponding main reactions are shown below. (1)
Fenton Reaction [75]: H2 O2 þ FeðIIÞ ! FeðIIIÞ þ HO þ HO FeðIIÞ þ O2 2 FeðIIIÞ þ O2 HO þ H2 O2 ! HOO þ H2 O
(2)
Photo-Fenton Reaction (UV Irradiation) [76]: FeðIIIÞ þ H2 O ! FeðIIÞ þ Hþ þ HO FeðIIÞ þ O2 2 FeðIIIÞ þ O2 O2 þ Hþ 2 HOO
(3)
Peroxide Decomposition by Heat or UV [77]: H2 O2 ! 2HO
Upon UV irradiation of Nafions partially exchanged with Fe(II) and Fe(III), weak ESR signals from perfluorinated radicals were detected at 77 K even in the
516
Shulamith Schlick and Krzysztof Krucza"a
absence of H2O2. The intensity of the ESR signals increased significantly in the presence of H2O2; the membrane-derived fragment was identified as the chain end perfluorinated radical RCF2CF2, which was also detected in g-irradiated PTFE. The ESR spectrum was simulated based on splittings from four F nuclei, two in a and two in b positions. As the hfs of the b-fluorine nuclei were different compared to those detected in PTFE, it was proposed that the chain-end radical in Nafions was formed by attack of oxygen radicals on the side chain [74,78]. Some of the membranes considered as alternatives to Nafions contain aromatic building blocks, in particular sulfonated phenyl groups or grafted polystyrene side chains. For this reason, toluene sulfonic acid (TSA) was chosen as a model compound to investigate its reactions with HO radicals as a function of pH. HO radicals were generated by direct photolysis of aqueous solutions of H2O2 in the presence of p-TSA in a flow cell in the resonator of the ESR spectrometer [78–80]. Additional species, such as HOO , O2 at higher pH, and O , also play important roles; moreover, small amounts of SO3 derived from the acid group were also detected. The chemistry of TSA depends strongly on pH, a fact that is highly significant in view of the possible pH inhomogeneities in fuel cells at high current. The intermediate pH regime is dominated by the presence of the cyclohexadienyl radical as a product of HO addition to the ring. The benzyl radical is thought to arise at low pH by acid-catalyzed H2O-elimination from the cyclohexadienyl radical, a reaction that requires a hydrogen atom at the a-carbon in the aromatic ring. At high pH, the elimination of water may be base-catalyzed.
3.2 Spin trapping of short-lived radical species formed during polymer degradation Spin trapping is a widely used method for the identification of transient radicals (e.g., HO , HOO , H , SO3, NO ) in biological systems and the study of their kinetics [41–52]. Recent applications of this method to polymeric materials is a relatively new development: Spin trapping by DMPO was used for the detection of radicals in Fenton media in the presence and absence of Nafions perfluorinated ionomers [81]. For water as solvent, only the DMPO/ OH adduct s was detected, both in the absence and presence of Nafion . In Nafions/water exposed to the Fenton reagent at 358 K for 3 h, a DMPO adduct of a carboncentered radical was also identified and assigned to a Nafions-derived fragment; its exact nature is under investigation. The exposure temperature, 358 K, was chosen because this is the typical operating temperature of fuel cells. Comparison with the results of a direct ESR study of Nafions exposed to the Fenton reagent indicated that spin trapping by DMPO can provide complementary information on the type of radicals present during Nafions degradation. Spin trapping experiments have been performed recently in a fuel cell inserted in the ESR resonator (‘‘in situ’’ cell), using DMPO and a-(4-pyridyl-1oxide)-N-tert-butylnitrone (POBN) as the spin traps [78,82,83]. These experiments allowed the separate examination of spin adducts at the anode and cathode sides.
ESR and ESR Imaging Methods
517
The H-adduct of POBN was detected at the anode side (g ¼ 2.0056, aN ¼ 15.10 G, aH ¼ 9.82 for two H atoms); at the cathode, the DMPO–HO adduct was detected. Recently, the degradation mechanism in model compounds for the fluorinated ionomer membranes has been investigated using spin trapping ESR methods, with the goal to shed light on the more complicated degradation processes in the polymeric membranes. In the case of perfluro-(2-ethoxyethane) sulfonic acid (CF3CF2OCF2CF2SO3H, PFEESA) as the model compound for the Nafions side chain and MNP as the spin trap, adducts from F atoms and RF2CF2 radicals have been identified [84].
4. ESR IMAGING: A NONDESTRUCTIVE METHOD FOR SPATIALLY RESOLVED POLYMER DEGRADATION 4.1 ESR imaging of polymers stabilized by hindered amines Degradation processes can be studied by ESRI in polymers containing HAS; this approach was originally suggested by Ohno, who presented 2D spectral– spatial ESRI images of radicals in PP containing two different stabilizers, but no detailed analysis was offered [85]. The method is based on the formation of stable nitroxide radicals derived from HAS (HAS–NO) during UV- or thermal treatment. ESRI based on HAS–NO represents an important step in the development of ESRI beyond phantoms, because the nitroxides are part of the system, and participate in, and reflect on, degradation processes. Detailed studies based on this approach have been published: Lucarini et al. have determined by 1D ESRI the distribution of the nitroxide radicals in UV-irradiated PP containing a hindered amine stabilizer [56–58]. Figure 8 presents the spatial variation of nitroxide intensity in plaques of thickness 2 mm that were UV-irradiated for the indicated times; the lower nitroxide intensity in the center of plaques after the longer treatment times was explained by the DLO concept. The DLO regime and high oxidation rates lead to narrow penetration depth of oxygen. Recently, Marek et al. have reported 1D and 2D ESRI imaging experiments on polystyrene and PP plaques exposed to thermal aging and UV irradiation [86].
4.2 1D and 2D spectral–spatial ESRI in heterophasic polymers ESRI methods have been developed in our Detroit laboratory for the study of heterophasic systems such as ABS [14,40,59,87–89] and HPEC [61,90], both containing bis(2,2,6,6-tetramethyl-4-piperidinyl) sebacate (Tinuvins 770) as the stabilizer, and exposed to thermal treatment and UV irradiation. The HAS–NO provided the contrast necessary in the imaging experiments. The major objectives were to examine polymer degradation under different conditions; to assess the effect of rubber phase, polybutadiene (PB) in ABS and ethylene–propylene rubber (EPR) in HPEC, on the extent of degradation; and to evaluate the extent of
518
Shulamith Schlick and Krzysztof Krucza"a
Figure 8 Evolution of the spatial distribution of nitroxide radicals across polypropylene plaques of thickness 2 mm and containing HAS, after the indicated UV irradiation times. The arrow indicates the irradiated side. Adapted and reprinted from Lucarini et al. [56b]. Copyright 1996, with permission from Elsevier.
stabilization by HAS. The repeat units in HPEC and ABS polymers are presented below.
For the ESR and ESRI experiments, the polymers containing 1–2% Tinuvins 770 were prepared as 10 cm 10 cm 0.4 cm plaques by injection molding at 483 K. Thermal treatment of the plaques was performed in convection ovens, at 333–393 K for ABS samples, and at 393–433 K for HPEC samples. UV irradiation of the plaques
ESR and ESR Imaging Methods
519
was carried out in weathering chambers at 338 K with a Xe arc that mimics sunlight, or at 318 K with UVA (maximum intensity 320–380 nm) or UVB (maximum intensity 290–330 nm) sources. For the ESR and ESRI experiments, cylindrical samples with 4 mm in diameter were cut through the plaque thickness at selected time intervals, each was transferred to a 5 mm in diameter ESR sample tube, and placed in the ESR resonator with the symmetry axis along the long (vertical) axis of the resonator and parallel to the direction of the magnetic field gradient. X-band ESR spectra at 300 K of the HAS–NO in UV-irradiated ABS consist of a superposition of two components, from nitroxide radicals differing in their mobility: a ‘‘fast’’ component (width E32 G), and a ‘‘slow’’ component (width E64 G). These spectra indicated the presence of HAS–NO radicals in two different environments, and were assigned to nitroxides located, respectively, in low-Tg domains dominated by B sequences (TgE200 K), and in high-Tg domains dominated by S (TgE370 K) or AN sequences (TgE360 K), as seen in Figure 5. The composite ESR spectra were deconvoluted into the two components; by superimposing the two components in various ratios, it was possible to reproduce all composite spectra and to determine the relative concentration of each component as a function of type and duration of the treatment. The decrease of the relative intensity of the fast component with irradiation time was explained by the consumption of the HAS-derived nitroxide radicals located in B-rich domains of the polymer, as the B component is expected to be more vulnerable to degradation compared to the other repeat units in ABS [40]. While the presence of the two spectral components, fast and slow, is due to the heterophasic nature of ABS, the variation of the fast/slow ratio with irradiation time is, however, due to chemical reactions; in this way a connection was established between the concentration and ESR line shapes of the nitroxides, and the degradation process. A similar situation was encountered for thermally treated and UV-irradiated HPEC samples [61,90]. As nitroxide radicals are not expected to intercalate in crystalline domains, the measured ESR spectra reflect dynamics in the amorphous domains. The major conclusion deduced from the spectra shown in Figure 5 is that the two sites detected for the nitroxides in the heterophasic systems studied can serve as a basis not only for describing the morphology of the system, but also to trace the evolution of the nitroxide signal as a function of treatment time, and the time-dependence of the degradation process, in the morphologically different domains: in the B-rich and SAN-rich domains in ABS, and in the amorphous PP-rich and EPR-rich (ethylene–propylene–rubber-rich) domains in HPEC. In other words, the HAS-derived nitroxides in the stabilized heterophasic polymer systems provide not only the contrast needed in the imaging experiments, but also detailed information on the extent of degradation within the sample depth, and in the morphologically different microdomains. 1D ESRI experiments provided the concentration profiles of the nitroxides for the various aging methods; and 2D spectral–spatial ESRI experiments described the spatial variation of the ESR spectra with sample depth, in terms of the variation of the fast/slow ratio with sample depth. In both ABS and HPEC samples, the variation of percentage fast with sample depth was translated
520
Shulamith Schlick and Krzysztof Krucza"a
into ‘‘spectral profiles’’, which reflected the loss of the elastomer component (PB in ABS, and EPR component in HPEC) as a function of sample depth. For this reason, these profiles were termed ‘‘elastomer profiles’’; they indicated the loss of the elastomer properties due to thermal or UV irradiation. The intensity and elastomer profiles were obtained nondestructively. This approach represents an advantage compared to microtoming the sample, especially in HPEC systems, which are partially crystalline and the degree of crystallinity can alter during microtoming. The following major conclusions were deduced from the ESRI studies of degradation in the heterophasic polymers: The HAS were found to be antiprotective during thermal degradation in both ABS and HPEC systems. UVB irradiation leads to more advanced degradation compared to UVA; this conclusion is based on the examination of 1D profiles, and by considering the degradation depth, as shown in Figure 9. The degradation in HPEC depends on the amount of EPR: thermal degradation is more advanced in samples containing more EPR, but the opposite is true in the case of UV irradiation, where less EPR leads to more advanced degradation. This conclusion was rationalized by assuming that the diffusion of oxygen is higher at the higher temperatures of thermal degradation (393 K and 433 K). The opposite result in UV-irradiated samples was explained by assuming that the point of attack is the tertiary carbon in PP, and samples containing more PP are more vulnerable to degradation. ESRI results were compared with results obtained by Fourier transform infrared (FTIR) in the same samples. FTIR is a well-established technique used (a) UVA irradiated HPEC, 20 days
UVB
UVA
0.0
(b) UVB irradiated HPEC, 20 days
0.5
1.0 1.5 2.0 Depth / mm
2.5
3.0
0.0
0.5
1.0 1.5 2.0 Depth / mm
2.5
3.0
Figure 9 Concentration profiles of nitroxide radicals in HPEC after 20 days of irradiation by UVA (a) and UVB (b) sources. Note the more homogeneous distribution of radicals on the left, due to slower degradation kinetics in UVA-irradiated samples.
ESR and ESR Imaging Methods
521
for detection of carbonyl and other groups formed by degradation. The comparison indicated that ESRI is an excellent technique for the detection of early events in polymer degradation, and is more sensitive than FTIR.
5. CONCLUDING REMARKS Polymer degradation, which reflects changes in the properties of polymers due to chemical processes that occur as a function of a complex set of environmental conditions, is a challenging topic of great fundamental and technological importance. Historically, materials were used long before their properties were fully understood. In recent years, analytical tools such as microscopy, imaging, and computational techniques have made possible the determination of structural and functional details of materials, some of which are hard to obtain by other methods. ESR spectroscopy, used in the direct detection or spin trapping modes, is a sensitive method for the detection of polymer fragments and for determining the degradation mechanism. Recent applications for the study of stability in ionomer membranes used as proton exchange membranes in fuel cells demonstrate the capability of ESR to detect details that cannot be obtained by other methods. The ESRI experiments described in our publications and summarized in this chapter led to spatially resolved information on the effect of treatment conditions, amount of stabilizer, and polymer composition on the degradation rate. In the heterophasic systems studied in our laboratory, ESRI has identified specific morphological domains where chemical processes are accelerated. The combination of 1D and 2D spectral–spatial ESRI experiments led to mapping of the stabilizer consumption on two length scales: within the sample depth on the scale of a few mm, and within morphological domains on the scale of a few mm. ESRI is a nondestructive method for the study of degradation, which is an important advantage, especially for crystalline polymers. The major advantage of ESRI compared with FTIR methods is its sensitivity to early events in the aging process. Further developments of ESRI methods are expected to be of help in the ultimate goal: accurate predictions of lifetimes for polymeric materials and a better understanding of the environmental factors. The ESRI method requires the presence of a contrast agent, HAS–NO in our work. The implication is that ESRI is an exceptionally sensitive and specific method for observing degradation in HAS-stabilized polymers, but not in polymers in general; this advantage and this limitation is similar to ESR methods, which are specific to, and applicable only, when radicals are present.
ACKNOWLEDGEMENTS ESR and ESRI studies in the Detroit laboratory have received sustained and generous support from the Polymers Program of the National Science Foundation. Efforts in Poland were supported by the Ministry of Education and Science, grant number 3 T09A 051 28. We acknowledge with gratitude the
522
Shulamith Schlick and Krzysztof Krucza"a
collaboration with John L. Gerlock, which was supported by the University Research Program of Ford Motor Company. We are grateful to K. Ohno, P. Eagle, and S.-C. Kweon for getting us started in the ESRI field; to J. Pilar and A. Marek from the Institute of Macromolecular Chemistry in Prague, Czech Republic for their major contributions to all aspects of ESRI in the Detroit laboratory; and to K. Kruczala, T. Spalek, and Z. Sojka of the Jagiellonian University, Cracow, Poland for implementation of the Genetic Algorithm in the ESRI software.
REFERENCES 1 J.H. O’Donnell, In: E. Reichmanis and J.H. O’Donnell (Eds.), The Effects of Radiation on HighTechnology Polymers, American Chemical Society, Washington, DC, 1989, Chapter 1, pp. 1–13. 2 S.H. Hamid, M.B. Amin and A.G. Maadhah (Eds.), Handbook of Polymer Degradation, 1st ed., Marcel Dekker, New York, 1992. 2nd ed., 2000 3 E. Reichmanis, C.W. Frank and J.H. O’Donnell (Eds.), Irradiation of Polymeric Materials: Processes, Mechanisms, and Applications, American Chemical Society, Washington, DC, 1993. 4 R.L. Clough, N.C. Billingham and K.T. Gillen (Eds.), Polymer Durability: Degradation, Stabilization and Lifetime Prediction, Adv. Chem. Series 249. American Chemical Society: Washington, DC, 1996. 5 J.L. Bolland, Proc. Roy. Soc., A186 (1946) 218. 6 L. Bateman, Q. Rev. (London), 8 (1947) 147. 7 L. Audouin, A. Gueguen, A. Tcharkhtchi and J. Verdu, J. Polym. Sci. Part A, Polym. Chem., 33 (1995) 921. 8 J. Pospisil and P.P. Klemchuk, In: J. Pospisil and P.P. Klemchuk (Eds.), Oxidation Inhibition in Organic Materials, CRC Press, Boca Raton, FL, 1990, pp. 1–10. 9 (a) J.L. Gerlock, D.R. Bauer and L.M. Briggs, Polym. Degrad. Stab., 14 (1986) 53–71. (b) J.L. Gerlock, T. Riley and D.R. Bauer, Polym. Degrad. Stab., 14 (1986) 73–84. (c) J.L. Gerlock and D.R. Bauer, Polym. Degrad. Stab., 14 (1986) 97–112. (d) J.L. Gerlock, A.V. Kucherov and C.A. Smith, Polym. Degrad. Stab., 73 (2001) 201 and references therein. 10 K.T. Gillen and R.L. Clough, Polymer, 33 (1992) 4359. 11 J. Wise, K.T. Gillen and R.L. Clough, Radiat. Phys. Chem., 49 (1997) 565. 12 N.C. Billingham, In: G. Scott (Ed.), Atmospheric Oxidation and Antioxidants, Elsevier, Amsterdam, 1993, Vol. II, Chapter 4, pp. 219–277. 13 N.M. Emanuel and A.L. Buchachenko, Chemical Physics of Molecular Destruction and Stabilization of Polymer, VNU Science Press, Utrecht, Netherlands, 1987. 14 M.V. Motyakin and S. Schlick, Polym. Degrad. Stab., 91 (2006) 1462 and references therein. 15 J. Pospisil, Adv. Polym. Sci., 124 (1995) 87. 16 See website: http://www.cibasc.com/ind-pla-pol-pop-products.htm. 17 G. Scott, In: G. Scott (Ed.), Atmospheric Oxidation and Antioxidants, , Elsevier, Amsterdam, 1993, Vol. II, Chapter 5, pp. 279–326. 18 A. Carrington and A.D. McLachlan, Introduction to Magnetic Resonance, with Applications to Chemistry and Chemical Physics, Harper & Row, New York, 1967. 19 R.S. Alger, Electron Paramagnetic Resonance: Techniques and Applications, Wiley-Interscience, New York, NY, 1968. 20 A. Abragam and B. Bleaney, Electron Paramagnetic Resonance of Transition Ions, Clarendon, Oxford, UK, 1970. 21 C.P. Poole, Jr., Electron Spin Resonance: A Comprehensive Treatise on Experimental Techniques, 2nd ed., Wiley, New York, 1983. 22 J.R. Pilbrow, Transition Ion Electron Paramagnetic Resonance, Clarendon, Oxford, UK, 1990. 23 L. Kevan and M.K. Bowman (Eds.), Modern Pulsed and Continuous-Wave Electron Spin Resonance, Wiley, New York, NY, 1990. 24 J.A. Weil, J.R. Bolton and J.E. Wertz, Electron Paramagnetic Resonance: Elementary Theory and Practical Applications, Wiley, New York, 1994. 25 A. Schweiger and G. Jeschke, Principles of Pulse Electron Paramagnetic Resonance, Clarendon, Oxford, UK, 2001.
ESR and ESR Imaging Methods
523
26 A.M. Wasserman, In: B.C. Gilbert, M.J. Davies and D.M. Murphy (Eds.), Specialist Periodical Reports-Electron Paramagnetic Resonance, Royal Society of Chemistry, Cambridge, 1996, Vol. 15, pp. 115–152. 27 D. Goldfarb, In: B.C. Gilbert, M.J. Davies and D.M. Murphy (Eds.), Specialist Periodical Reports — Electron Spin Resonance, Royal Society of Chemistry, Cambridge, 1996, Vol. 15, pp. 186–243. 28 A. Smirnov, In: B.C. Gilbert, M.J. Davies, D.M. Murphy and K.A. McLauchlan (Eds.), Specialist Periodical Reports — Electron Paramagnetic Resonance, , Royal Society of Chemistry, Cambridge, 2002, Vol. 18, pp. 109–136. 29 B. Ra˚nby and J.F. Rabek, ESR Spectroscopy in Polymer Research, Springer-Verlag, Berlin, 1977. 30 S. Schlick (Ed.), Advanced ESR Methods in Polymer Research, Wiley, Hoboken, NJ, 2006. 31 S. Schlick and G. Jeschke, Electron spin resonance. In: J.I. Kroschwitz (Ed.), Encyclopedia of Polymer Science and Engineering. Wiley-Interscience, New York, NY, 2004, pp. 614–651, Chapter 9. Web edition: 15 July 2004. Hardcopy edition: 15 August 2004. 32 G. Jeschke and S. Schlick, In: S. Schlick (Ed.), Advanced ESR Methods in Polymer Research, Wiley, Hoboken, NJ, 2006, Chapter 1, pp. 3–24. 33 G. Jeschke, In: S. Schlick (Ed.), Advanced ESR Methods in Polymer Research, Wiley, Hoboken, NJ, 2006, Chapter 2, pp. 25–51. 34 L.J. Berliner (Ed.), Spin Labeling, Theory and Applications, Academic Press, New York, 1976. 35 L.J. Berliner (Ed.), Spin Labeling II, Theory and Applications, Academic Press, New York, 1979. 36 L.J. Berliner and J. Reuben (Eds.), Biological Magnetic Resonance: Spin Labeling, Vol. 8, Plenum, New York, NY, 1989, 37 C.J. Bender and L.J. Berliner (Eds.), Instrumental Methods in Electron Magnetic Resonance, Biological Magnetic Resonance, Vol. 21, Kluwer Academic/Plenum Publishing Corporation, New York, NY, 2004. 38 R.F. Boyer and S.E. Keineth (Eds.), Molecular Motions in Polymers by E.S.R., Symposium Series Vol. 1. MMI Press: Harwood, Chur, 1980. 39 G.G. Cameron and I.G. Davidson, In: A.H. Fawcett (Ed.), Polymer Spectroscopy, Wiley, Chichester, UK, 1996, Chapter 9, pp. 231–252 40 M.V. Motyakin, J.L. Gerlock and S. Schlick, Macromolecules, 32 (1999) 5463–5467. 41 E.G. Janzen and B.J. Blackburn, J. Am. Chem. Soc., 90 (1968) 5909. 42 E.G. Janzen, Acc. Chem. Res., 4 (1971) 31. 43 C. Lagercrantz, J. Phys. Chem., 75 (1971) 3466. 44 G.M. Rosen, B.E. Britigan, H.J. Halpern and S. Pou, Free Radicals: Biology and Detection by Spin Trapping, Oxford University Press, New York, 1999. 45 C. Motley and R.P. Mason, In: Biological Magnetic Resonance, Plenum, New York, 1989, Vol. 8, Chapter 10, pp. 489–546. 46 (a) J.R. Harbour, V. Chow and M.L. Hair, Can. J. Chem., 52 (1974) 3549. (b) J.R. Harbour and M.L. Hair, J. Phys. Chem., 82 (1978) 1397. 47 B. Kalyanaraman, C. Mottley and R.P. Mason, J. Biochem. Biophys. Methods, 9 (1984) 27. 48 M.J. Davies and T.F. Slater, Biochem. J., 240 (1986) 789. 49 R. Dabestani, R.D. Hall, R.H. Sik and R.H. Chignell, Photochem. Photobiol., 52 (1990) 961. 50 P. Bilski, C.F. Chignell, J. Szychlinski, A. Borkowski, E. Oleksy and K. Reszka, J. Am. Chem. Soc., 114 (1992) 549. 51 Spin Trapping Database: http://epr.niehs.nih.gov. 52 Y. Kotake and E.G. Janzen, J. Am. Chem. Soc., 113 (1991) 9503. 53 L.J. Berliner and H. Fujii, Science, 227 (1985) 517. 54 M. Van Kienlin and R. Pohmann, In: P. Blu¨mler, B. Blu¨mich, R. Botto and E. Fukushima (Eds.), Spatially Resolved Magnetic Resonance: Methods, Materials, Medicine, Biology, Rheology, Ecology, Hardware, Wiley-VCH, Weinheim, 1998, Chapter 1, pp. 3–20. 55 S.-C. Kweon, Z. Gao, P. Eagle, S. Schlick, J. Labsky and J. Pilar, Polym. Mat. Sci. Eng. (Proc. ACS Div. PMSE), 71 (1994) 169. 56 (a) M. Lucarini, G.F. Pedulli, V. Borzatta and N. Lelli, Res. Chem. Intermed., 22 (1996) 581. (b) M. Lucarini, G.F. Pedulli, V. Borzatta and N. Lelli, Polym. Degrad. Stab., 53 (1996) 9. 57 M. Lucarini and G.F. Pedulli, Angew. Makromol. Chem., 252 (1997) 179.
524
Shulamith Schlick and Krzysztof Krucza"a
58 P. Franchi, M. Lucarini, G.F. Pedulli, M. Bonora and M. Vitali, Macromol. Chem. Phys., 202 (2001) 1246. 59 M.V. Motyakin and S. Schlick, Polym. Degrad. Stab., 76(1) (2002) 25. 60 M.V. Motyakin and S. Schlick, Macromolecules, 35 (2002) 3984–3992. 61 K. Kruczala, J.G. Bokria and S. Schlick, Macromolecules, 36 (2003) 1909. 62 G.R. Eaton, S.S. Eaton and K. Ohno (Eds.), EPR Imaging and In Vivo EPR, CRC Press, Boca Raton, FL, 1991. 63 S. Hara, K. Yamamoto, S. Shimada and H. Nishi, Macromolecules, 36 (2003) 5661–5665. 64 E. Adem, G. Burillo, E. Munoz, J. Rickards, L. Cota and M. Avalos-borja, Polym. Degrad. Stab., 81 (2003) 75. 65 J.S. Forsythe and D.J.T. Hill, Prog. Polym. Sci., 25 (2000) 101. 66 L. Kevan and S. Schlick, J. Phys. Chem., 90 (1986) 1998 and references therein. 67 M.G. Alonso-Amigo and S. Schlick, Macromolecules, 20 (1987) 795. 68 P. Pfluger, M.T. Krounbi, G.B. Street and G. Weiser, J. Chem. Phys., 78 (1983) 3212. 69 A. Adachi and J. Yamauchi, Synth. Met., 73 (1995) 101. 70 M. Hasik, A. Pron, J. Pozniczek, A. Bielanski, Z. Piwowarska, K. Kruczala and R. Dziembaj, J. Chem. Soc. Faraday Trans., 90(14) (1994) 2099. 71 I. Kulszewicz-Bajer, M. Zagorska, J. Pozniczek, A. Bielanski, K. Kruczala, K. Dyrek and A. Pron, Synth. Met., 39 (1991) 41. 72 (a) J. Pozniczek, I. Kulszewicz-Bajer, M. Zagorska, K. Krucza"a, A. Bielanski, K. Dyrek and A. Pron, J. Molec. Catal., 67 (1991) 223. (b) J. Pozniczek, I. Kulszewicz-Bajer, M. Zagorska, K. Krucza"a, A. Bielanski, K. Dyrek and A. Pron, J. Catalysis, 132 (1991) 311. 73 A. Bosnjakovic and S. Schlick, J. Phys. Chem. B, 108 (2004) 4332. 74 M.K. Kadirov, A. Bosnjakovic and S. Schlick, J. Phys. Chem. B, 109 (2005) 7664. 75 C. Walling, Acc. Chem. Res., 8 (1975) 125. 76 A.R. Freitas, G.J. Vidotti, A.F. Rubira and E.C. Muniz, Polym. Degrad. Stab., 87 (2005) 425. 77 J. Bednarek and S. Schlick, J. Phys. Chem., 95 (1991) 9940. 78 E. Roduner and S. Schlick, In: S. Schlick (Eds.), Advanced ESR Methods in Polymer Research, Wiley, Hoboken, NJ, 2006, Chapter 8, pp. 197–228. 79 G. Hu¨bner and E. Roduner, J. Mater. Chem., 9 (1999) 409. 80 G. Hu¨bner, H.P. Brack, G.G. Scherer, E. Roduner, Proceedings of the 17th Annual Membrane Technology/Separations Planning Conference, Newton, MA, 6–7 December, 1999, p. 304. 81 A. Bosnjakovic and S. Schlick, J. Phys. Chem. B, 110 (2006) 10720. 82 A. Panchenko, H. Dilger, J. Kerres, M. Hein, A. Ullrich, T. Kaz and E. Roduner, Phys. Chem. Chem. Phys., 6 (2004) 2891. 83 A. Panchenko, H. Dilger, E. Mo¨ller, T. Sixt and E. Roduner, J. Power Sources, 127 (2004) 325. 84 S. Schlick and M. Danilczuk, Polym. Mat. Sci. Eng. (Proc. ACS Div. PMSE), 95 (2006) 146. 85 K. Ohno, In: S.S. Eaton, G.R. Eaton and K. Ohno (Eds.), EPR Imaging and In Vivo EPR, CRC Press, Boca Raton, FL, 1991, Chapter 18, p. 181. 86 A. Marek, L. Kapralkova, P. Schmidt, J. Pfleger, J. Humlicek, J. Pospisil and J. Pilar, Polym. Degrad. Stab., 91 (2006) 444. 87 K. Kruczala, M.V. Motyakin and S. Schlick, J. Phys. Chem. B, 104 (2000) 3387. 88 M.V. Motyakin and S. Schlick, Macromolecules, 34 (2001) 2854. 89 M. Lucarini, G.F. Pedulli, M.V. Motyakin and S. Schlick, Prog. Polym. Sci., 28 (2003) 331. 90 K. Kruczala, W. Aris and S. Schlick, Macromolecules, 38 (2005) 6979.
SECTION V: Polymer Product Analysis
This page intentionally left blank
CHAPT ER
13 Spatial Imaging/Heterogeneity Peter Wilhelm and Boril Chernev
Contents
1. Introduction 2. Raman and FTIR Microscopy 2.1 Raman microscopy 2.2 FTIR microscopy 3. Examples of Heterogeneous Polymers Investigated by IR and Raman Microscopy 3.1 FTIR transmission images compared with SEM images 3.2 Raman global images 3.3 IR-ATR images 3.4 Radiation damage: a Raman imaging study 3.5 Polymer laminates: IR vs. Raman 3.6 Confocal Raman microscopy 4. Other Methods and Comparison of Methods 4.1 Near-infrared imaging 4.2 Scanning near-field optical microscopy 4.3 Time-of-flight secondary ion mass spectrometry 4.4 Nuclear magnetic resonance imaging and electron spin resonance imaging 4.5 Micro X-ray fluorescence microscopy and microspectroscopy 4.6 Photoelectron spectroscopy 4.7 Laser enhanced ionization spectroscopy and resonance ionization spectroscopy 5. Conclusions References
527 529 529 534 538 538 540 541 542 545 549 550 550 551 552 552 554 555 555 557 558
1. INTRODUCTION The physical and chemical properties of complex samples are strongly influenced by the spatial distribution of their chemical components [1]. Thus, analytical methods that provide information on both the molecular nature and the Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00413-3
r 2008 Elsevier B.V. All rights reserved.
527
528
Peter Wilhelm and Boril Chernev
localization of their components (both organic and inorganic) are essential for the design and fabrication of advanced heterogeneous materials. Vibrational spectroscopic imaging methods, such as Fourier transform infrared (FTIR) spectroscopy and Raman spectroscopy, are particularly attractive methods, as they provide both chemical and spatial information simultaneously. The spectrally and spatially resolved chemical information can be quickly collected, analysed and visualised — even for systems that do not have much inherent visible contrast in conventional light or electron microscopy [2,3]. The whole potential of new materials systems [4–6], whether they might be manufactured of a single compound or be a composite, can only be evaluated, if the microscopic details down to the molecular or atomic level are fully understood. This is absolutely mandatory, if the development of new products is to be successful and in keeping up with today’s demands. Thermoplastic polymer macromolecules usually tend to become oriented (molecular chain axis aligns along the extrusion direction) upon extrusion or injection moulding. This can have implications on the mechanical and physical properties of the polymer. By orienting the sample with respect to the coordinate system of the instrument and analysing the sample with polarised Raman (or infrared) light, we are able to get information on the preferred orientation of the polymer chains (see, for example, Chapter 8). Many polymers may also exist in either an amorphous or crystalline form (degree of crystallinity usually below 50%, which is a consequence of their thermal and stress history), see, for example, Chapter 7. We will start our discussion in this chapter with Raman microscopy, simply because the optical setup of a Raman microscopy instrument very closely resembles that of a light microscope, and a typical analytical investigation often starts by judging the visual appearance of a product. After a short survey of the measuring (or illumination) techniques using Raman microscopy (point measurement, line scanning, mapping and imaging) we will discuss the spatial resolution achievable and its limitations. Then we will continue with a discussion of FTIR spectroscopy and microscopy and its various sampling methods; FTIR spectroscopy currently probably yields the richest chemical information overall for both organic and polymeric species. Furthermore, novel two-dimensional (array) detectors with a high number of detector elements allow the creation of images based on vibrational spectroscopic information with a lateral spatial resolution close to the wavelength of the mid-infrared radiation. Several practical examples will be used to illustrate the possibilities and limitations of these methods for the characterization of heterogeneous materials. A comparison with and consideration of other spectroscopic and imaging methods, including X-ray fluorescence, timeof-flight secondary ion mass spectrometry (ToF-SIMS), nuclear magnetic resonance (NMR), electron-spin resonance spectroscopy (ESR), photoelectron spectroscopy (PES), scanning near-field optical microscopy (SNOM), laser enhanced ionization spectroscopy (LEIS) and resonance ionization spectroscopy (RIS), will complete our survey, with the aim of giving the analyst or researcher in a scientific or industrial laboratory a suggestion, or at least an idea, of which is the right method and methodology for the characterization of a particular heterogeneous polymer.
Spatial Imaging/Heterogeneity
529
2. RAMAN AND FTIR MICROSCOPY Vibrational spectroscopy is based on the interaction between light and matter; it probes the different vibrational states of the investigated molecules. A number of excellent books describing the principles, instrumentation and applications are available [7,8].
2.1 Raman microscopy While infrared spectroscopy has been used as a routine tool in analytical laboratories for a long time, Raman spectroscopy was largely confined in its use until the 1990s to only a few experts, until advances in instrumentation (lasers, Notch filters, charge-coupled device (CCD) detectors) facilitated a broader acceptance and opened up many new fields of application in analytical investigations and quality control [9–11]. In particular, the combination of Raman spectroscopy with a light microscope has proved to be an essential tool for materials analyses [12]. To assess the spatial resolution of a dispersive Raman microscopy system (using excitation lasers in the visible range) the same relation valid for light microscopy applies.
2.1.1 Raman single point spectrum The easiest way of investigating a sample with a Raman microscope is by focusing the laser beam onto its surface and collecting the scattered light with the same optics in 1801 backscattering geometry. This reveals information of the probed sample volume defined by the magnification power of the microscope objective and confocality. Using an excitation source in the visible range of the spectrum and a standard 50 objective on the microscope, the diameter of the laser spot on the sample will be about 1–2 mm. The penetration of the laser beam into the sample and the so-called depth of focus have to be considered also, which describe the finite region around the theoretical focal point in which the laser beam waist diameter remains unchanged. The depth of focus (dof) can be calculated with Equation (1). dof ¼
4l ðsin aÞ2
(1)
where l is the wavelength of the excitation laser and a the half of the opening angle of the objective. When investigating opaque or transparent samples, where the laser light can penetrate the surface and be scattered into deeper regions, Raman light from these deeper zones also contributes to the collected signal and is of particular relevance with non-homogeneous samples, e.g., multilayer systems or blends. The above equation is only valid, if the beam is focused on the sample surface. Different considerations apply to confocal Raman spectroscopy, which is a very useful technique to probe (depth profile) samples below their surface. This nondestructive method is appropriate for studies on thin layers, inclusions and impurities buried within a matrix, and will be discussed below.
530
Peter Wilhelm and Boril Chernev
2.1.2 Raman spectroscopy line scanning Line scanning can be performed conventionally by collecting a number of spectra at equidistantly spaced points along a line. By taking full advantage of a twodimensional CCD detection system this can save time. A computer-controlled optical scanner focuses the laser beam as a line on the sample plane. The Raman scatter emanating from this line on the sample plane is subsequently projected onto the entrance slit of the spectrometer and then imaged onto a row of the CCD. This approach provides simultaneous acquisition of Raman signals from each point of the sample illuminated by the scanned laser line [13].
2.1.3 Confocal Raman microscopy This technique can provide both high lateral spatial and depth resolution. The fundamental principle of confocal Raman microscopy is the same as in confocal light microscopy. Small pinholes or apertures are placed in the back focal plane of the microscope in order to isolate a small sample volume, from which the emerging Raman light is focused onto the detector. In the original approach small pinholes were used to select the sample volume (Figure 1) [14]. Another technique works with one mechanical aperture and the two-dimensional CCD as a second electronic aperture [15] in order to avoid time-consuming optical alignments. The fundamentals and theory for application and practical limitations of confocal Raman microscopy have been discussed by Everall [16,17]. In the papers referenced above it has been shown that depth resolutions around 2–3 mm collected with a 100 microscope objective are possible. However, the depth resolution will degrade as one probes deeper into the sample; this is a consequence of refraction caused by refractive index changes at the sample surface and boundaries within the sample. The greater the depth probed, the greater the dof becomes if an air objective is used; the situation can be improved and aberrations minimised if an oil immersion objective is used [16,17].
2.1.4 Raman spectroscopy mapping Raman microscopy can be used to map large sample areas. Equidistant single spot Raman spectra are collected sequentially within a grid pattern on the sample surface. Both the spatial and chemical information recorded form a ‘‘data cube’’, as illustrated in Figure 2 [18]. Variations of Raman data and hence of chemical and/or physical properties related to this spectroscopic data over the sample can be followed and mapped from such data sets. One example is to use a normalised band intensity, another is to integrate the area of a single band, which is characteristic for the presence of a specific polymer, polymer phase or additive/filler, in the investigated composite material. Depending on the spectral richness and changes occurring in the sample a number of different maps can be created, based on such as the distribution of a specific band or band ratios. All considerations for measurements of single spot Raman spectra also hold for mapping because the measuring technique is essentially identical. The spatial resolution in a map depends also on the distance between the single points and can be altered from map to map. By increasing the distance, the spatial resolution
Spatial Imaging/Heterogeneity
531
Figure 1 Principle of confocal Raman microscopy: A laser spot in the focal plane passes through the pinhole P. A laser spot at a distance z from the focal plane is projected in the image plane with size P’, and is largely blocked by the pinhole P. (L ¼ lens; M ¼ beam splitter; f1, f2 ¼ focal length of lens L1 and L2, respectively; b2 ¼ image distance of out-of-focus laser spot). Reproduced from Tabaksblat et al. [14], with permission of the Society for Applied Spectroscopy. r 2000.
in the map worsens, but larger sample areas can be probed in a shorter timescale. This is especially advantageous when structures within the sample are large compared to the resolution of a single spot spectrum; experiment times get longer if the investigated area is extended or the number of grid points increased. Technically, the area that can be probed is only limited by the dimension of the moveable microscope stage. In the z-direction (depth-direction) the resolution is determined by the confocal instrument settings. While it is essential to be aware of the limitations of confocal measurements, as mentioned above, it is possible to create threedimensional maps. That means probing a sample in the x, y and z-directions. In Figure 2 the data cube of a two-dimensional map is shown. One element (row) of the cube has been picked out and its content enlarged on the right side of the figure. It is evident that each row therefore contains the information of a whole spectrum.
532
Peter Wilhelm and Boril Chernev
Figure 2 Data cube generation in mapping and imaging. The four-dimensional hyperspectral data cube contains the full spectral information, absorbance vs. wavenumber (n, cm1), for each x,y pixel from the imaged area, as is shown above. A horizontal slice through that cube contains a chemical image (e.g., band intensity at selected n for each x,y pixel of the image) as is shown below. The latter result could be obtained by Global Imaging (in which only the intensity distribution of a certain band over the imaged area would be recorded).
2.1.5 Raman spectroscopy global imaging The wide-field illumination technique is an alternative method of Raman imaging. It is faster than both the point- and line-scanning (mapping) methods, but might be more sensitive to artefacts arising from scattering effects due to the topography of the investigated surface [19]. Global imaging can also be applied for characterising larger areas. However, the area is limited practically due to decreasing illumination density on the sample surface when defocusing the laser (see below). Generally, this technique is of higher spatial but of worse spectral resolution than mapping. Possibilities for data treatment are limited, since this image is only a slice through the so-called hyperspectral data cube, but not a set of real spectra. Only certain image arithmetic operations are possible, but no spectral treatment (e.g., band approximation) can be done. The method uses a different approach to create the data cube. An image of the whole area of interest is generated in one single measurement essentially over a particular narrow wavenumber region, selected by using a filter, and exploiting the CCD essentially as a camera. These images only contain Raman information over a very narrow spectral range (about 20 wavenumbers typically). To obtain a complete data set, a sequential recording of images at different wavenumber would be necessary. Although, for many applications, especially if the investigator is interested only in one specific species
Spatial Imaging/Heterogeneity
533
(whose presence in the sample can be assumed), it is sufficient to register only a few narrow wavenumber band images to reveal the unknown details, which is also very timesaving. Area selection on the specimen is done by defocusing the laser spot onto the image plane over the desired size. Defocusing the laser beam means going away from a convergent sample illumination towards a parallel one. Then the foci of the laser beam and the microscope objective are not in the same plane anymore. Altering or lowering the microscope stage would bring the specimen out of focus and no sharp image could be created at the CCD camera. The diameter of the probed area is determined by the magnification of the objective and the degree of defocusing. The maximum is reached, when a collimated laser beam is directed onto the sample surface. With a standard 50 objective the investigated area is normally a circle about 50 mm in diameter. At this stage, it has to be kept in mind that the laser intensity per unit area on the sample decreases with the square of the circle radius and acquisition times for images with similar signal-to-noise ratios take longer by the same factor. Selection of the spectral range can be performed with dielectric band-bass filters, whose spectral resolution is about 20 cm1. The selected wavenumber region should be free of any other band that could interfere with the Raman signal of interest. To account for the background, another image has to be registered and subtracted from the first one. This background image will be collected from exactly the same imaged area, but in a spectral region that has no Raman bands from the observed sample. This approach will also account for inhomogeneities in laser intensity distribution and features arising from fluorescence. When defocusing the laser spot, depth resolution information gets lost. Confocal arrangements are not possible anymore and therefore threedimensional global images cannot be acquired. A further disadvantage of global imaging is that scattered light from deeper sample regions can reach the detector and deteriorate the lateral spatial resolution of the technique, which normally is limited either by diffraction or the pixel size on the CCD camera, if smaller objectives are used. Each detector element of the CCD camera counts the incoming photons of specific energy selected by the filters. In contrast to mapping it is not possible to change the distance between single measuring points; only the magnification of the objective can alter the sample size examined by one pixel. Global Raman imaging can be a fast and simple technique, providing high lateral spatial resolution (down to the diffraction limit corresponding with the excitation laser wavelength) images of the sample of interest. There are several techniques available. A CCD array collects simultaneously the spectral data emanating from an array of spatial locations on the irradiated sample surface [20]. Thus, recorded is a three-dimensional data cube, with two coordinates representing the sample and one for the spectral dimension at each (x,y) point (cf. Figure 2). The spectral dimension in this case is only the intensity of a certain Raman band, used to identify the component of interest. This band should be unique for the component of interest of the sample and its intensity should be high enough in
534
Peter Wilhelm and Boril Chernev
Figure 3 Global Raman imaging: Experimental setup and example image of a silicon wafer with letter ‘‘E’’ printed on it. Image taken at 520 cm1 (Silicon Raman mode).
order to obtain reasonable images. The wavenumber region interrogated is usually done by using a tuneable filter, so that while the whole sample is imaged, one wavelength or narrow wavelength region is selected from the inelastically scattered light [21–24] and imaged onto the CCD. A simple example is shown in Figure 3. Filtering can be done in various ways: by, for example, a monochromator, an electrical band-pass filter, an acousto-optic tuneable filter or a liquid crystal tuneable filter. This type of imaging carries no chemical information about the presence of other components in the sample. By using a tuneable filter however, it is possible to collect a slice through the spectral dimension z, thus ‘‘reconstructing’’ the hyperspectral (complete) chemical image. There is a number of alternative Raman imaging techniques; these include using the Hadamard transform technique [25–27], and such as fibre-bundle image compression, which however is not yet commercially available [26–31]. However in the latter approach, the laser power on the sample could be high, since the beam is not defocused, and the possibility of sample damage increases.
2.2 FTIR microscopy Infrared spectroscopy is based on an absorption process. It does not use a monochromatic light source, but uses a broad-band source covering the whole mid-infrared region (and beyond). The mid-infrared region of the electromagnetic spectrum refers to wavelengths between 25,000 and 2,500 nm (4,000–400 cm1). In this chapter the terms ‘‘infrared’’ or ‘‘IR’’ will be used to indicate the midinfrared region. When interacting with a sample, some parts of the electromagnetic spectrum can excite vibrations, which lead to the photons of appropriate frequency for some molecular excitations to be absorbed. The absorbed part of the infrared beam can be expressed in terms of absorbance or
Spatial Imaging/Heterogeneity
535
percentage loss in transmitted light compared to a reference beam (i.e., without the absorbing sample) [8]. Due to the nature of the interaction process and different measuring requirements, a number of different ways of sample preparation and presentation are available. Whereas Raman spectra can usually be acquired without any further sample preparation, if the sample fits under the microscope (1801 backscattering geometry), samples for infrared transmission spectroscopy have to be of appropriate thickness, which typically is a few micrometers thickness. As most spectra from polymer samples are acquired from continuous solids, this often requires a microtome for sample preparation.
2.2.1 IR spectroscopy transmission spectra In transmission mode a spatial resolution of about 15–20 mm can be achieved with infrared microscopes [32]. This is generally sufficient to properly identify such as small impurities, inclusions, gels or single components of multilaminate foils. Similar to Raman spectroscopy, line profiles or maps over larger sample areas can be performed. In an FTIR microscope Cassegrainian objectives are used for focusing the beam. The objective illuminates the sample, and, in transmission mode, after passing through the specimen the infrared light is collected by the condenser. To confine the investigated area, apertures (a mask, most commonly rectangular) are used; these are usually sited in a remote image plane. Theoretically these apertures can be made very small. However, there are practical limitations, because the spatial resolution of FTIR microscopes is limited by diffraction (see Section 2.2.4).
2.2.2 IR-ATR spectra In materials investigations surface-sensitive techniques are of special interest. The major contribution of infrared spectroscopy to this field is internal reflection spectroscopy (IRS), often called the ‘‘attenuated total reflection’’ (ATR) technique. To describe theory and principle, electromagnetic wave theory must be applied [33]. In practice a crystal of a material with high refractive index n1 (the ATR crystal), such as diamond (n1 ¼ 2.4), zinc selenide (n1 ¼ 2.4), silicon (n1 ¼ 3.4), or germanium (n1 ¼ 4.0) is brought into contact with the surface of a specimen with lower refractive index n2 (for polymers n2 is approximately 1.5). The infrared beam passing through the ATR crystal is directed to this crystal-sample interface at an angle greater than the critical angle ac to ensure that only internal (total) reflection occurs at the crystal-sample boundary, and that the infrared throughput is as high as possible. The critical angle is given by: sin ac ¼ (n2/n1). Simply visualised, the infrared beam penetrates (of the order 0.3–3 mm, dependent on its wavelength) just beyond the ATR crystal-specimen boundary before it is reflected back and makes its way through the crystal to the detector. On this short path (of the evanescent wave) into the sample surface layer, light is absorbed, and the reflected beam carries characteristic spectral information of the sample. The decaying amplitude of the evanescent wave and the depth of penetration dp at which it has decreased to a proportion of 1/e is defined by the Harrick equation (Equation (2)), where l is the wavelength of the incoming
536
Peter Wilhelm and Boril Chernev
infrared radiation. l dp ¼ sffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffiffi n2 2pn1 sin2 a n1
(2)
From this equation it can be seen that the depth of penetration depends on the angle of incidence of the infrared radiation, the refractive indices of the ATR element and the sample, and the wavelength of the radiation. As a consequence of lower penetration at higher wavenumber (shorter wavelength), bands are relatively weaker compared to a transmission spectrum, but surface specificity is higher. It has to be kept in mind that the refractive index of a medium may change in the vicinity of an absorption band. This is especially the case for strong bands for which this variation (anomalous dispersion) can distort the band shape and shift the peak maxima, but mathematical models can be applied that correct for this effect, and these are made available as software commands by some instrument manufacturers.
2.2.3 FTIR spectroscopy imaging With FTIR imaging chemical and physical parameters of the sample can be displayed in a multicolor or grey-scale diagram (as discussed above with Raman imaging), when band intensities and/or position are evaluated by appropriate software. Modern instruments have overcome the drawbacks of mapping experiments (time-consuming, poor spatial resolution) by using focal plane array (FPA) detectors, consisting of a large number of mercury cadmium telluride (MCT) detector elements (64 64 elements FPAs are probably most commonly used, but smaller and larger array sizes are offered by the instrument manufacturers). Detectors of this kind acquire, e.g., 4,096 complete infrared spectra simultaneously, which can then be used for image creation. Acquisition time is typically in the range of several minutes. Until recently spectra had to be acquired using the step-scan mode FTIR technique, which means that an interferogram is created by a step-wise detector readout. Improvements in detector design and electronics mean that the 64 64 FPA can now be used with an FTIR spectrometer operating in the more conventional rapid scanning mode. When used for transmission measurements, an FPA detector with 64 64 elements can probe an area of about 270 mm 270 mm (with a standard 15
Cassegrainian objective). Specimen thickness needs to be a few microns thick, typically about 10 mm or less. Detailed information about instrumentation and applications may be found in two books published recently [34,35]. An increase in lateral and depth resolution can be obtained by recording images in the ATR mode. The increase in spatial resolution can be explained by the higher refractive index (n1) of the ATR medium between the sample and the objective (ATR crystal instead of air). Example papers dealing with resolution in FTIR imaging have been published recently inter alia by Sommer et al. [36] and Kazarian and Chan [37]. Further details on IR imaging and on different sampling approaches, together with practical applications in polymer science can be found in [38–40].
Spatial Imaging/Heterogeneity
537
2.2.4 Spatial resolution: mapping vs. imaging Light passing through apertures is diffracted, due to its wave nature, and the diffraction increases with decreasing aperture size. The resulting diffraction pattern of a uniformly illuminated circular aperture has a bright region in the centre, known as the Airy disc or Airy pattern (originally used in astronomy to describe the quality of a telescope, and named after George Airy), which is surrounded by concentric rings. The diameter of this disc is related to the wavelength of the illuminating light and the size (f-number) of the circular aperture. The angle from the centre at which the first minimum occurs is: sin y ¼ 1.22 (l/d), where l is the wavelength of the light and d the diameter of the aperture [41]. The resolution or ‘‘resolving power’’ of a light microscope is usually specified as the minimum distance between two lines or points in the imaged object, at which they will be perceived as separated by the observer. The Rayleigh criterion [42] is extensively used in optical microscopy for determining the resolution of light microscopes. It imposes a resolution limit. The criterion is satisfied, when the centre of the Airy disc for the first object occurs at the first minimum of the Airy disc of the second. This minimum distance r can then be calculated by Equation (3). 1:22l (3) 2n sin a where l is the wavelength of the radiation, n the refractive index of the medium between sample and objective (in most cases air), and a half the opening angle of the objective. Often the term nsina is called the numerical aperture (NA) of the system. The theoretical spatial resolution, as deduced from Rayleigh criterion, however, is significantly deteriorated by diffraction effects at the edges of apertures such as those used in conventional IR microscopy. The deleterious effect of these apertures can easily be demonstrated by a simple experiment (Figure 4). The sample is a thin layer of a polymer (in our case an epoxy resin) on a diamond window. Spectra were collected with a standard 15 Cassegrainian objective (NA ¼ 0.4) using rectangular apertures of size 15 mm 50 mm. The sample was moved under the apertures in a way that the region before, at and beyond the sample’s cut edge was scanned, taking spectra near the edge and even outside (where only air and the supporting diamond window should have contributed to the IR spectrum). It has been shown, that even at a distance of 10 mm off from the polymer edge, spectral features of the polymer can be detected. Taking into account these considerations, improved spatial resolution (in contrast to conventional mapping techniques) may be obtained by three ways: r¼
1. 2.
3.
Avoiding apertures — i.e., using FPA detectors. Using characteristic absorption bands at higher wavenumber (shorter wavelength) — i.e., O–H and C–H absorptions (in many cases not really helpful unless they are specific). Using the ATR technique, if appropriate.
538
100
Peter Wilhelm and Boril Chernev
1 Polymer
Air
60
3 4
100 80
50
50
2
5
Rectangular apertures: 15 μm * 50 μm
1: in polymer 2: near cut edge
80
3: half over edge 4: air, near polymer 6
5: 10 μm away
0.00 4000
3500 3250 3000 2750 2500 2250 2000 1750 1500 1250 1000 750
6: 20 μm away
Figure 4 Demonstration of diffraction effect of an aperture: The spectra 1–6 were recorded sequentially by moving the sample stage under the 15 mm 50 mm aperture.
Table 1 Approximate values for r (Rayleigh criterion) estimated for three characteristic wavenumbers; typical instrument parameters for transmission and ATR experiments assumed Absorption band (Wavenumber, cm1)
NA ¼ 0.4 (15 Cassegrainian objective, air) (Transmission, mm)
NA ¼ 2.4 (20 ATR objective, Ge) (ATR, mm)
1,000 (C–O, Si–O) 1,700 (CQO) 3,000 (C–H)
15 9 5
3 2 1
Table 1 shows some approximate r values calculated for frequently used absorptions. NA values are assumed for customary Cassegrain objectives (for transmission and ATR, respectively). The following sections will deal with some polymer examples, for which we tried to confirm the conclusions drawn from these theoretical considerations.
3. EXAMPLES OF HETEROGENEOUS POLYMERS INVESTIGATED BY IR AND RAMAN MICROSCOPY 3.1 FTIR transmission images compared with SEM images The first example will deal with polymer blends consisting of polyamide (PA) and poly(tetrafluoroethylene) (PTFE). These polymer types are frequently used
Spatial Imaging/Heterogeneity
539
for friction bearings. PTFE has excellent gliding properties, but is expensive and hard to process. PA can easily be processed and is tough and resilient to many chemicals. However, compounding both materials is a challenging task for polymer chemists. Several procedures have been developed to make PTFE more reactive and compatible. The first sample is a reactive poly(tetrafluoroethylene)/polyamide 6 (PTFE/ PA) blend [43]. When mixing PTFE micro-powder and PA in an extruder at about 2801C, relatively large PTFE particles occur in the final product because of immiscibility. By irradiation with electrons in air reactive groups in the PTFE powder are formed. These functionalised particles react with the molten PA in the extruder, and graft copolymers are formed, improving the compatibility of the components. At the same time a decrease in PTFE particle size proportional to the irradiation dose can be observed, and a PTFE/PA compound with better properties is produced. Figure 5 shows an FTIR transmission image together with a scanning electron microscopy (SEM) micrograph of the same area of the blend material (5 mm thick section, area: 270 mm 270 mm). Images were taken with a Bruker Hyperion 3000 FTIR microscope, equipped with a 64 64 pixel FPA. PTFE cluster sizes vary over a wide range (from below 1 mm to approximately 100 mm). The material is porous, with some holes. Spatial resolution of the IR image is as expected (see Section 2.2.4). Small PTFE clusters of 8–10 mm can be distinguished with their dimensions well comparable to those in the SEM micrograph. IR spectra were taken with 27750
150 100
Micron
27700
50 0
27650 27600 27550 27500
10 μm
0.00
48550 48600 48650 48700 48750 48800 Micron
3750 3500 3250 3000 2750 2500 2250 2000 1750 1500 1250 1000
Figure 5 FTIR transmission image of a PA/PTFE blend (left) and SEM image from the same area (right). PTFE distribution was calculated from the 1,210 cm1 C–F absorption (intensity: cf. color scale in the middle). The arrow indicates from where on the image the IR spectrum was extracted. The orange ovals show identical PTFE clusters as detected by FTIR and SEM, respectively. (See Color Plate Section at the end of this book.)
540
Peter Wilhelm and Boril Chernev
8 cm1 spectral resolution, 10 scans in continuous scan mode were collected, and the total scan time was ca. 3 min [44,45].
3.2 Raman global images The second example, a blend sample consists of 80% PA 6.6, 18% PTFE and 2% silicone oil. From the relative concentrations, it can be seen that PA forms the matrix and provides the necessary stability to the bearing. PTFE acts as an incorporated lubricant. The two main components are not chemically linked. Therefore, silicone oil has been added to work as a boundary lubricant during the break-in phase of the bearing. Due to its liquid nature, it quickly migrates to the surface when pressure is applied and prevents abrasion at the first stage. Shortly after, a thin film of PTFE forms at the interface between the thermoplastic bearing and the counter part. The goal of our investigations was to characterise the morphology of the sample, and to determine the size and location of the PTFE and silicone oil phases by different methods [46,47]. For phase characterization using Raman microscopy, no special sample preparation was necessary. For FTIR imaging, microtomed sections (5 mm in thickness) had to be prepared by cutting the sample with a diamond knife at 801C (‘‘cryo-microtomy’’) to prevent smearing and to obtain flat surfaces. Raman spectroscopy allows chemical identification of single phases and in the imaging mode a description of the morphology. Raman bands characteristic of the two main components PA and PTFE are easily distinguishable, as shown in Figure 6, where pure materials have been used from which to record reference spectra. To identify PTFE in the spectra of the bearing the symmetric C–F
Figure 6 Reference Raman spectra of poly(tetrafluoroethylene) (a) and polyamide 6,6 (b).
Spatial Imaging/Heterogeneity
541
Figure 7 CCD global images of the PA/PTFE sample (see text for details) measured at 731 cm1 (a) and 790 cm1 (b). Image (c) is the result of the background subtraction (ab). The area of the image is 20 mm 20 mm.
stretching vibration at 731 cm1 was used, which is the strongest band in the Raman spectrum. The distribution of PTFE particles in the matrix can be shown by Raman imaging. The laser spot was defocused to cover a region about 30 mm in diameter. This is a good compromise between a large probed sample area and high signal intensity at reasonable acquisition times. Background due to weak inherent fluorescence and noise was removed by subtraction of an image obtained at 790 cm1, where neither PA nor PTFE give a strong signal (Figure 7). Bright areas represent a high number of counts, which is a high concentration of PTFE. Only a small background is observed in the PA region and a slightly higher one in the PTFE-rich zones. This can be due to different impurities in the feedstock. With the subtraction procedure the background and inhomogeneities of laser intensity distribution are minimised. The theoretical lateral spatial resolution achievable with Raman imaging using the optical arrangements of our system (50 objective with NA ¼ 0.75, 633 nm HeNe laser) should be about 1 mm. In this investigation the resolution is worse than predicted. In practice, sample drift during long acquisition times, uneven surface structures and penetration of laser light into the material worsen the lateral spatial resolution to a value of about 2 mm (estimated). The Raman images in Figure 7 show that PTFE clusters in the sample are between 8 and 20 mm in diameter [46]. These results have also been confirmed by FTIR imaging and SEM [47].
3.3 IR-ATR images ATR imaging (Figure 8) of the same PA/PTFE blend (discussed in the preceding section) fully supported the assumption of obtaining significantly better spatial resolution due to the high refractive index Ge ATR crystal. Experiments were carried out with a Bruker Hyperion 3000 FTIR microscope (64 64 pixel FPA detector, area of the images: 50 mm 50 mm). The representation of the PTFE clusters (by integration of 1,149 cm1 C–F absorption) is quite clear, see Figure 8, left. It is also possible to use chemometric multivariate data analysis (principal components analysis, PCA) on the FTIR-image and, thus carry out a more revealing data treatment and analysis, see Figure 8, right. Statistical routines
542
Peter Wilhelm and Boril Chernev
34320
Z[Micron]
34320
34300
34300
34280
34280
36580
36600
36620
36580
36600
36620
Figure 8 IR-ATR images of a PA/PTFE polymer blend; bright colors: PTFE clusters. Left: integration of 1,149 cm1 C–F absorption. Right: PCA factor plot — additional clusters appear within the white circles. (See Color Plate Section at the end of this book.)
available within the program package OPUSt (Bruker Optik GmbH, Germany) were used. These routines, however, should be handled with great care with respect to potential different evaluation artifacts. So far we have only discussed the two main components of the blend. The third component is silicone oil, which scatters Raman light rather relatively weakly. A concentration of only 2% in the material turned out to be too low for detection with our system, even at increased data acquisition times. Fortunately, silicone absorbs strongly in the infrared region, and hence may be detected by FTIR imaging (by integration of 1,261 cm1 Si–C absorption band), even in the presence of PTFE (strong absorptions at 1,150 and 1,210 cm1). PCA was performed on the data set, as described above, to confirm the results. Figure 9a shows the same area of the sample as Figure 8, but with integration of the silicone band. From the IR results it is obvious, that silicone oil is located mainly at the interface between PA and PTFE (acting as a mediator between the two chemically different polymer species), but it is also distributed within the PA, presumably in small holes (ready to act as a first lubricating agent in friction bearings). Again this finding has been confirmed by SEM and X-ray spectroscopy [47], which is shown in Figure 9b. This is an example, where scanning electron microscopy with an energy dispersive X-ray spectroscopy (EDXS) probe can successfully used even on a polymer sample, though many types of polymers usually give very low contrast due to the lack of heavy atoms (apart from carbon and oxygen). A lateral resolution (below 1 mm) as provided by SEM cannot be reached by conventional vibrational spectroscopy (with the exception of SNOM-based techniques).
3.4 Radiation damage: a Raman imaging study The main application of the imaging methods, as already mentioned, is the ability to visualize various distributions of components within a sample. Figure 10
543
Spatial Imaging/Heterogeneity
34320
2[Micron]
34320
34300
34280
34300
34280
36580
36600
36620
36580
36600
36620
36580
36600
36620
34320
34300
1500
1000
34280
(a)
(b)
Figure 9 (a) FTIR ATR image of silicone oil distribution in PA/PTFE blend. Top left: integration of 1,261 cm1 (Si–C) band (cf. IR spectrum of the blend shown below); top right: after PCA; bottom right: PTFE distribution (1,149 cm1). Bright color means high concentration. (b) SEM/EDXS elemental mapping of fluorine (red) and silicon (green) in a PA/PTFE/Silicone blend. Size of the image: 40 mm 40 mm. (See Color Plate Section at the end of this book.)
544
Peter Wilhelm and Boril Chernev
Figure 10 Global Raman image of PTFE distribution in PA-matrix; image taken at 731 cm1: Left: white light micrograph; center: Raman image; right: the same image after image enhancement and edge detection.
shows an example; the sample was PTFE dispersed in 6,6-polyamide matrix (PA). The Raman image was created at 731 cm1 (C–F stretch) recorded from a microtomed cross-section of the material. Total accumulation time was 60 s and a 50 objective was used. Background correction was performed by subtracting a background image taken at 790 cm1. Although there is some fluorescence background due to a prior electron beam irradiation, it is clear that the irradiated PTFE clusters, which appear darker on the white light visible micrograph, do not appear in the Raman image. Instead of that, clusters from underneath (just below the microtomed surface) give distinct Raman signal so that they appear clearly in the image. Images of this sample were obtained also by environmental SEM (ESEM). Because of the advantages of ESEM (no coating of electrically non-conductive samples necessary), it was possible to image the same area first in ESEM, then in the Raman microscope, and afterwards to repeat that cycle again. In the ESEM both, the secondary electron (SE) and back-scattered electron (BSE) images were taken. In both methods the penetration depth is several micrometers (depending on the exciting beam energy and interaction of photons or electrons with matter). That phenomenon might account for some differences in the initial images (Figure 11, upper images). During the second observation in the ESEM (Figure 11, lower images) some additional PTFE clusters (obviously somewhat below the surface) became visible (especially in the right half of the backscattered electron image), and clusters at the surface appear very bright (charging by electrons). A subsequent Raman image revealed that the clusters originally at the surface were destroyed by the ESEM electron beam, and new clusters became visible, obviously due to a certain destruction (and melting) of the PA surface [48]. Briefly, this means that multiple analyses on the same sample should be carefully considered with respect to the potential sample damage during the analyses, thus leaving the most ‘‘destructive’’ method to be the final one — in this case SEM.
545
10
Spatial Imaging/Heterogeneity
10
0
-10
Raman images
-10
0
before ESEM
10 0
after ESEM -10 -20 -10
0
10
Figure 11 Raman (left) and ESEM (right, SE and BSE) images (for explanation see text). (See Color Plate Section at the end of this book.)
Table 2
Individual layers of the polymer laminate
EVA LLDPE-MAH COPA LLDPE-MAH EVA LLDPE-MAH COPA LLDPE-MAH EVA
45 mm 5 mm 32 mm 5 mm 66 mm 5 mm 32 mm 5 mm 45 mm
Notes: EVA, ethylene vinyl acetate; LLDPE-MAH, maleic anhydride grafted linear low-density polyethylene; COPA, co-polyamide.
3.5 Polymer laminates: IR vs. Raman In this example a polymer laminate film (for packaging) was examined, which was composed of nine layers (see Table 2), by both FTIR imaging and Raman line scan. For the IR measurements thin sections (5 mm) were cut. The central ethylene/vinyl acetate (EVA) copolymer layer is very soft, and holes can be seen in the visible image (Figure 12). The EVA and co-polyamide (COPA) layers are resolved quite well by FTIR transmission imaging (Figure 12), but the 5 mm linear low-density polyethylene/ maleic anhydride grafted (LLDPE-MAH) layers cannot be detected in this mode. Infrared ATR images showed an intermediate region between COPA and EVA of about 5 mm (Figure 13). However, a clear identification of that layer as MAH-modified LLDPE was not possible due to the low MAH content.
546
22900
22900
20
Z[Micron]
Z[Micron]
10 22800
22800 0
22750
22750
22700
22700
34550
34600 34650 X[Micron]
34700
34500
34550
34600 34650 X[Micron]
34700
(404150.00527)
0.00
0.50
1.00
34500
3800 3600 3400 3200 3000 2800 2600 2400 2200 2000 1800 1600 1400 1200 1000
Figure 12 IR transmission images of a polymer laminate. Left: video image. Right: IR image of the amide band (bright: high COPA concentration). Only the COPA layers are visible in the FTIR image. The horizontal features in the middle layer are holes, originating during microtoming due to the material’s softness.
Peter Wilhelm and Boril Chernev
22850
22850
0.6 0.8
6
7960 2 0 2000
1800
1600
1400
1200
1000
Wavenumber cm-1
7950
-2
7950
0.20
1.0
0.15
EVA: strong ester peak at 1740
0.5 7940
0.10
0.0 -0.5
0.05
7930
0.00
-1.0 2000
1800
1600
1400
1200 -1
1000
34250
34260
34270 X[Micron]
34280
34290
Wavenumber cm
Figure 13 FTIR ATR image of the polymer laminate (top left: IR spectrum of COPA layer; bottom left: IR spectrum of EVA layer). The amide I absorption of COPA (top right) and the ester absorption of EVA (bottom right) were integrated (high intensities represented in bright color). An Intermediate region of ca. 5 mm (dimension bar) is assumed to be the LLDPE-MAH layer. Image area: 50 mm 50 mm.
Spatial Imaging/Heterogeneity
Wavenumber
8
7970
4
0.2 0.4 0.0
Wavenumber
1.0
10 COPA: strong peak at 1640, very weak at 1740
547
548
Peter Wilhelm and Boril Chernev
The corresponding carbonyl absorption bands should appear at 1,790 and 1,740 cm1, but did not show in the ATR spectra. A simple line scan with Raman microscopy, however, clearly showed the LLDPE-MAH layer as a ca. 5-mm broad plateau from the evaluation of three different Raman band intensities (Figure 14). In this case a simple Raman line scan obviously is the better choice for a determination of the LLDPE-MAH layer thickness, superior even to IR-ATR imaging. We used three Raman bands
Figure 14 (a) Raman spectra of the individual layers; 1, LLDPE-MAH; 2, COPA; 3, EVA (abscissa: wavenumber (cm1), ordinate: intensity in arbitrary units). (b) Raman line scan of polymer laminate using three different Raman bands (abscissa: position in mm, ordinate: intensity in arbitrary units).
Spatial Imaging/Heterogeneity
549
at: 2,846 cm1 (nCH2, polyethylene), 1,635 cm1 (nCO, amide, COPA) and 1,293 cm1 (EVA).
3.6 Confocal Raman microscopy In modern analytical laboratories investigations of samples often need to be done in the shortest time possible, especially when problems in a production process have to be overcome. Consequently, sample preparation should be as simple as possible to save both time and money. In the production of polymer films, blurring and inclusions (‘‘gels’’) are among the commonly reported faults. FTIR microscopy has been a useful technique for the identification of organic contaminants. Unfortunately, sample preparation can be laborious in many such cases, because appropriate samples for infrared study have to be prepared by laborious and time-consuming microtome techniques. However, an inclusion causing a blurring in a polypropylene (PP) film (Figure 15) was identified readily by a confocal Raman experiment, performed with a Renishaw System 2000 Microscope, using a HeNe
Figure 15 Light microscopy image and Raman spectra of an inclusion in PP film. Top, white light micrograph of the inclusion in the PP film. Bottom, Raman spectra, taken at the surface of the PP film (PP) and 12 mm underneath the film surface (inclusion). The spectrum of the inclusion is compared with the reference spectrum of an additive (taken from a supplied reference sample).
550
Peter Wilhelm and Boril Chernev
(633 nm) laser as excitation source. The upper spectrum in Figure 15, taken at the film surface (above the inclusion) represents a well-resolved and undisturbed PP spectrum. By moving the focus down into the PP matrix in steps of 2 mm, at a depth of 12 mm additional peaks appeared (middle spectrum). By comparing the spectrum with that of a reference sample (lower spectrum) the inclusion could clearly be identified as that of an additive. In summary it may be said, that confocal Raman spectroscopy enables spectra to be collected from within well-defined regions in a sample. The system must be correctly configured to achieve best confocal operation, where light from the region of interest is accepted, whilst light from the adjacent (out of focus) regions is rejected. When in confocal mode the spatial resolution is improved. Spatial resolution has two components: lateral resolution (in the plane of the microscope stage) which is typically 1–2 mm and, depth of focus which is 2.5–5 mm using the 50 objective.
4. OTHER METHODS AND COMPARISON OF METHODS A number of other methods such as magnetic resonance imaging, ToF-SIMS or X-ray photoelectron spectroscopy (XPS), are also widely used for a variety of imaging experiments on polymer materials and products. Other techniques, for instance, micro X-ray fluorescence (XRF) imaging or SNOM, although popular analytical approaches are, however, not comparatively widely used as far as polymer characterization is concerned. In the following sections we will try to cover the most commonly applied techniques with respect to imaging applications in polymer science, and, also comment on the less utilised techniques for this field of study, which are nevertheless interesting either because of their outstanding spatial resolution or for another characteristic capability that is unique or complementary. Our focus will, however, stay on the commonly achievable spatial resolution with imaging experiments.
4.1 Near-infrared imaging Near-infrared chemical imaging (NIR-CI) refers usually to the hyperspectral imaging of samples using typically wavelengths from 0.9 to 2.5 mm (NIR region) and an FPA detector. There are some major methodical and instrumental differences between NIR and IR imaging. NIR images are taken exclusively in reflection geometry. Therefore, the method is mainly surface-sensitive with a limited penetration depth. The NIR spectra contain less structural information than the corresponding IR spectra, since only the overtone absorptions of X–H (X ¼ C, N, O) are detected. Using chemometric approaches has, however, enlarged the applications of this method, particularly for quantitative and classification analyses. The theoretical spatial resolution of the method should be, depending on the wavelength, better than 10 mm/pixel [49] and, thus, better than the spatial
Spatial Imaging/Heterogeneity
551
resolution of the conventional (non-ATR) IR transmission or reflection imaging, but typically spatial resolutions of 30 mm/pixel and above are common in practice [50–53]. The potential spatial resolution advantage of NIR spectroscopy is offset by the much lower (10x100x), relative to mid-IR, intensities of the absorption features. Tran describes an imaging microscope working from the visible to the IR region with spatial resolution of about 1.5 mm at 600 nm [52]; then we might expect the best spatial resolution achievable in the NIR region to be about 2.2 mm (at 900 nm). Thus, the spatial resolution of the NIR imaging reaches that achievable with the IR-ATR imaging using a Ge crystal for instance (see previous section for details on IR-ATR imaging). A great advantage of NIR-CI is, however, the ability to routinely analyse rough samples. This means, that the area of interest does not necessarily need to be optically flat in order to obtain a good data set, unlike the requirement for transmission IR imaging or Raman global imaging. The detectors used in the NIR region are usually InSb or InGaAs, which are more sensitive, and nitrogen cooling is not required. The number of detector elements in an NIR detector array is fairly high — typically 240 320; the resulting data hypercube will usually be evaluated by using chemometric approaches.
4.2 Scanning near-field optical microscopy SNOM is a fairly new imaging method, which, in principle, allows one to overcome the Rayleigh criterion. It can be undertaken in both transmission or reflection mode. Basically, the light which is used to illuminate the sample comes out of a very tiny probe tip (usually a sharpened optical fibre) with an aperture of commonly less than 100 nm, which is smaller than the wavelength. Thus, the tip of the probe serves as a near-field light source, and this light is confined in the vicinity of the probe tip. In this way it is possible to illuminate a very small area of the sample (less than the diffraction limit) and, moreover, it is possible to combine this technique with classical spectroscopic methods such as fluorescence, Raman or infrared spectroscopy [54–59]. Typical lateral resolution of SNOM, as already mentioned, can be below 100 nm; it is commonly stated as being 10–1,000 nm. The lateral spatial resolution of SNOM-imaging depends actually on the size of the probe tip and not on the wavelength used; 70 nm was reported by Zeisel et al. [60] and 17 nm was reported by Lahrech et al., who used a 10.6 mm IR laser as light source [56]. According to theoretical calculations [61] the signal enhancement with TERS (tip-enhanced Raman spectroscopy) occurs in an area of about 5 nm diameter, which was also recently demonstrated [62,63]. Hartschuh et al. [63] performed Raman near-field spectral and imaging experiments on single isolated single-wall carbon nanotubes with a lateral resolution of about 25 nm and, moreover, followed the spectral variations along the nanotube. A slightly higher spatial resolution of 15 nm was reported by Anderson et al. [64]. The achievable spatial resolution in an FTIR-SNOM imaging experiment will, however, be poorer than that cited above because of different technical problems. Spatial resolutions in the range between 100 nm and several micrometers have
552
Peter Wilhelm and Boril Chernev
been cited, using FPA detectors [65–67], however this method does not seem to have yet become commonly applied.
4.3 Time-of-flight secondary ion mass spectrometry ToF-SIMS is a highly sensitive analytical approach, in particular for analysing very thin surface layers. Basically, the method uses an ion-analyser (time-of-flight mass-spectrometer) to detect the flight times of the generated secondary charged species. The ionization is usually carried out by using a metal ion gun and often also a secondary ionizer. The flight times are then used to calculate the m/z (mass/charge) ratios of the detected particles. ToF-SIMS can also be operated in an imaging mode, providing very high resolution images with lateral spatial resolution down to 100 nm for elemental detection at a depth of only several nanometers. For polymers, however, the spatial resolution is usually worse and depends on many factors such as the instrumental performance, or on the sample itself. Typically, a lateral spatial resolution in the micrometer range can be achieved when examining the secondary ions, and by monitoring certain fragmentations it could be improved to several hundreds of nanometers [68,69]. Fardim and Holmbom reported an improved spatial resolution and increased secondary ions count after coating of the sample with a conductive Au-Pd layer [70]. There is also a trade-off between the spatial and energy resolution in the ToF-SIMS microscope, meaning that an improvement of the spatial resolution by using long ion gun pulses worsens the focus to the micrometer range. The use of very short pulses, thus ensuring a good focus quality, results in a poor energy resolution. Therefore, for each investigation a compromise between spatial and energy resolution has to be met. Evaluation of the data by means of PCA makes the method quite attractive and enhances both the ease of data interpretation and the quality of the obtained results [71,72]. Valuable results with Tof-SIMS imaging have been obtained e.g., with paper samples. The distribution of papermaking chemicals on the surface of coated and uncoated papers is very important for its further treatment, such as printing. Figure 16 [70] is an example of use of the technique for chemical microscopy analysis of paper surfaces.
4.4 Nuclear magnetic resonance imaging and electron spin resonance imaging NMR imaging, also known as magnetic resonance imaging (MRI), is based on the irradiation of the sample with high-frequency radio waves, while it is subjected to a strong magnetic field. The nuclei of different atoms in the sample absorb radio waves at different frequencies under the influence of the magnetic field. The proton-NMR technique uses the responses of the hydrogen nuclei (protons) to the applied radio frequency; this is the most used technique. The ability to image atoms of carbon-13, fluorine-19, phosphorus-31, and other elements besides hydrogen permit physicians and researchers to use the technique for various tracer studies as well. NMR microscopy is a well-established technique,
Spatial Imaging/Heterogeneity
553
Figure 16 ToF-SIMS images of total ion current, AKD (alkyl ketene dimer) size, optical brightener and hexosan distribution on multipurpose paper surface after coating with Au–Pd. Reproduced from Fardim and Holmbom [70], with permission from Elsevier. r 2005.
routinely used to observe magnetic parameters and transport phenomena in small-scale structures (synthetic and biopolymers). Images are collected with micrometer resolution by the method of MRI. In the case of polymers the spatial resolution is about 100 mm [73]. State-of-the-art of today’s NMR microscopy has reached voxel resolution of B[3.5 mm]3 at 400 MHz, with B30 h acquisition time [74]. Despite the relatively poor spatial resolution and quite prolonged measuring times, the method has several advantages. The method is able to ‘‘look’’ into the sample without destroying it, and no microtomy is necessary. Then, it is possible to collect three-dimensional images (tomographs), thus making this method very attractive if three-dimensional information about certain distributions is of interest. This technique is also used as a very common diagnostic tool, since the chemical shift of water protons depends also on the mobility of the water molecules. Therefore, it is possible to discriminate between different tissues. A computer analyses the emissions from the hydrogen nuclei of water molecules
554
Peter Wilhelm and Boril Chernev
in body tissues and constructs images of anatomic structures based on the concentrations of such nuclei. This use of proton density makes it possible to produce images of tissues that are comparable, and in some cases superior, in resolution and contrast to those obtained with CT (computed tomography, X-ray) scanning — typically in the centimeter range. Moreover, since macroscopic movement affects NMR signals, the method can be adapted to measure blood flow. A closely related technique is ESR imaging. (The fundamentals of ESR imaging are discussed in Chapter 12.) Since the observed phenomenon is electron resonance and not a proton resonance, it is technically much more demanding and, hence, not so popular [75]. The first ESR imaging experiments were designed to image large biological objects with relatively low spatial resolution. Recently there are efforts to develop this method further and spatial resolution of 2–5 mm was reported [76]. The method is a powerful tool for different kinetics investigations, particularly for radicals [77]. The great advantage of these methods is the possibility of creating threedimensional distributions, also referred to as tomographs, which is not possible with FTIR spectroscopy and not always possible with Raman spectroscopy, if, for instance the sample is opaque. Different combined imaging methods are also possible. For instance, when a species exhibits more than one resonance, it may be advantageous to study both of them simultaneously. It is also possible to drive one resonance while detecting the other one in two oscillating magnetic fields for instance. Driving an NMR and detecting its effect on an ESR is known as ENDOR (electron-nuclear double resonance). ENDOR of hyperfine and super-hyperfine splittings is a good tool for detailed mapping of electron-spin densities. If ESR is used to increase certain nuclear magnetization, observed by NMR, the method is referred as to DNP (dynamic nuclear polarization). A useful reference for the study of polymer heterogeneity by ESR spectroscopy is [78]. The reader is also referred to the Chapter 12 by Schlick and Kruczala in this book, which covers ESR and polymer degradation, including imaging methods.
4.5 Micro X-ray fluorescence microscopy and microspectroscopy Micro X-ray fluorescence (mXRF) is a powerful and fast method, allowing multielement analysis of rather large areas with a spatial resolution of several micrometers. The ability of trace elements detection, extracting information about the oxidation state and chemical environment makes mXRF microscopy a very valuable and widely applicable analytical approach. Though, traditionally, this method enjoys a great popularity in inorganic chemical analysis, it can also successfully be applied to the spatially resolved investigations of different organic compounds, including also biological materials [79] and polymers and polymer composites [80,81]. The high spatial resolution of 1–50 mm [79,82,83] and the ability of short-time investigation of rather large areas (e.g., 10 cm 10 cm) by using imaging array
Spatial Imaging/Heterogeneity
555
detectors makes the method very attractive for a broad spectrum of applications. Furthermore, it is also possible to extend the mXRF imaging in the third spatial direction, thus creating tomographs with a good spatial resolution of about 10 mm [84].
4.6 Photoelectron spectroscopy PES, a method closely related to mXRF, detects the photoelectrons emitted from the sample after irradiation with an electromagnetic wave of sufficient energy. The effect in the case of UV-stimulated electron emission was actually the first photoelectron effect discovered, hence it is also known as the photoelectric effect. Depending on the type of photons used, there are different types of PES, such as UV-PES in the case of UV light, or XPS — also known as ESCA (electron spectroscopy for chemical analysis) — if X-rays are used [85]. A great advantage of the method is the ability to discriminate between the different electronic states of one element within the region of interest, thus making the method also interesting for the chemical analysis of organic materials, and polymer blends in particular [86–88]. Moreover, it is also possible to detect minor degradation products in the sample by XPS and this makes the method also interesting when performing stability studies. For instance, it is possible to detect the final degradation product polyenes in PVC by means of XPS [89,90], which are usually present in very minor concentrations (ppb and below). However, especially for the detection of polyenes, Raman spectroscopy is a very simple and powerful method, and might therefore be the method of choice in such cases. As with the most X-ray based methods, imaging detectors are widely used, thus making imaging experiments attractive and moreover quite fast [86]. The achievable spatial resolution is in the range 20–40 mm [86,91]. The possibility of applying multivariate image analysis to the raw data extends further the information depth [92] and the abilities of the method as well. A comparison of XPS and FT-IR imaging studies of different types of poly(vinyl chloride)/ poly(methyl methacrylate (PVC/PMMA) polymer blends has been reported by Artyushkova et al. [93]. The comparable lateral resolution and parallel imaging capabilities of both techniques allow for a direct comparison of surface (XPS) and bulk (FT-IR) investigation of the same material (Figure 17). XPS can therefore play a major role in the study of heterogeneous polymers, catalysts and catalytic processes. For a review of the capabilities of this technique refer to [94].
4.7 Laser enhanced ionization spectroscopy and resonance ionization spectroscopy In LEIS, which is conceptually quite similar to PES, the sample is irradiated with a monochromatic electromagnetic radiation (e.g., a laser). Thus, it is possible to excite electrons from the sample to energy levels approaching or even surpassing the ionization barrier [94]. The difference between LEIS and RIS is the mechanism
556
Peter Wilhelm and Boril Chernev
Figure 17 Comparison of XPS (left) and FT-IR PVC images for two different PVC/PMMA blends with constant PVC molecular weight and PMMA molecular weight 75 kDa (a) and 838.3 kDa (b), respectively. Reproduced from Artyushkova et al. [93], with permission of the Society for Applied Spectroscopy. r 2000.
of the ionization in the final phase of the process. With LEIS, the energy needed is transferred via a collision process; with RIS, this energy exactly equals the energy of the incoming photon so that an absorption process takes place. Thus, LEIS is actually a special technique or subdivision of RIS. Though these techniques are usually applied to trace element analyses with an outstanding sensitivity in the ppt (parts per trillion) range, it is also possible to use a resonance ionization imaging device, usually referred to as an RIID, to detect Raman scattered photons [95]. For instance, the use of RIID with helium as an active element in an optical spectroscopy system, such as a Raman confocal imaging microscope, will result in an enormous improvement of the spatial resolution down to the 25–30 nm range and, unlike with the near-field technique, the signals are strong enough so
Spatial Imaging/Heterogeneity
557
that clear images could be obtained [96]. Moreover, it is also possible to extend the images to the third spatial dimension with the already mentioned spatial resolution. Such a possibility is unique amongst the optical imaging methods.
5. CONCLUSIONS For the spectroscopist today it is very important to choose the right method, after a cost-benefit analysis, to match the demands of the customer or serve the purpose of his research as effectively as possible. For the characterization of heterogeneous polymers a broad range of methods and instruments is available. We have tried to list the most important of them, and to emphasize their pros and cons when used for polymer imaging. Infrared spectroscopy/microscopy certainly is the primary method of choice when organic substances have to be identified. Sample preparation usually is simple for identification purposes, but will be an issue for imaging experiments, and spatial resolution may then well be only in the range of a few micrometers, depending on the used experimental approach (transmission, ATR). Raman microscopy provides a spatial resolution slightly better than IR, and no sample preparation is necessary in many cases. It has advantages with special types of substances (e.g., systems containing conjugated double bonds, oriented systems, amorphous and crystalline carbon, oxides). SNOM techniques (with spatial resolution below 1 mm) have been more popular with Raman than with IR, so far, but as yet are not routinely practiced. NIR (near-infrared) imaging has also been well introduced into polymer characterization, mainly because no laborious sample preparation is necessary. Spatial resolution approaches the range of mid-infrared imaging. ToF-SIMS is one of the most sensitive and interesting methods for surface analysis, but intricate and expensive. It can be operated in imaging mode, with resolutions below 1 mm (though usually not with polymers). NMR and ESR are both well-established spectroscopic methods. Despite their still relatively poor spatial resolution with polymer imaging, the number of applications and publications in these fields is growing steadily. mXRF spectroscopy is a powerful and fast method, when multielement analyses and trace analyses are required, with good spatial resolution. PES can also discriminate between different electronic states of elements; its imaging resolution is in the range of several tenths of micrometers. LEIS and RIS may be used in combination with Raman spectroscopy, thus achieving a remarkable resolution (below 100 nm). Only few applications, however, can be found in the literature. The advantages of imaging (using multichannel detectors or global imaging methods) over conventional mapping experiments are obvious, whenever multicomponent samples have to be investigated: Measuring times are very much shorter, because many spectra can be recorded simultaneously.
558
Peter Wilhelm and Boril Chernev
Spatial resolution usually is better (e.g., because apertures are no longer necessary). The output of imaging experiments is readily comprehensible to nonspectroscopists (comparable to light and electron microscopy). Careful attention should be paid to sample preparation, however. The materials investigated may be changed by the preparation procedure (e.g., smearing during microtomy of soft materials at room temperature is avoided when using cryo-microtomy) or during the measurement (radiation damage, contact with ATR crystal, etc.). More useful information may often be obtained by a smart combination of several spectroscopic methods, e.g., IR and Raman — both methods giving complementary information on the same sample. Interesting results may be obtained by combining microspectroscopic with other microscopic techniques (light and electron microscopy, thermal microscopy). Scanning electron microscopes can be equipped with a wide range of different spectroscopic probes, such as X-ray spectroscopy, electron energy loss spectroscopy (EELS) and even Raman spectroscopy. Data evaluation exploiting chemometric methods (multivariate data analyses, PCA, etc.), already integrated in many commercial spectroscopy software packages, will further improve the results and enhance their reliability.
REFERENCES 1 D.R. Askeland and P.P. Pradeep, The Science & Engineering of Materials, 5th ed., ThomsonEngineering, 2005. 2 L.C. Sawyer and D.T. Grubb, Polymer Microscopy, Chapman and Hall, London, 1995. 3 A.R. Clarke and C.N. Eberhardt, Microscopy Techniques for Materials Science, Woodhead Publishing, 2002. 4 H.-J.P. Adler, D. Kuckling and J.C. Jung (Eds.), Advanced Polymeric Materials (Macromolecular Symposia), Wiley-VCH, 2000. 5 R. Borsali and V. Soldi (Eds.), Advanced Polymeric Materials (Macromolecular Symposia), Wiley-VCH, 2006. 6 G. Shonaike and S.G. Advani, Advanced Polymeric Materials, Taylor & Francis, 2005. 7 N.B. Colthup, L.H. Daly and S.E. Wiberley, Introduction to Infrared and Raman Spectroscopy, Academic Press, San Diego, 1990. 8 J.M. Chalmers and P.R. Griffiths (Eds.), Handbook of Vibrational Spectroscopy, Wiley, Chichester, 2002. 9 J.R. Ferraro and K. Nakamoto, Introductory Raman Spectroscopy, Academic Press, San Diego, 1994. 10 J.G. Grasselli and B.J. Bulkin (Eds.), Analytical Raman Spectroscopy, Wiley, New York, 1991. 11 E. Smith and G. Dent, Modern Raman Spectroscopy, Wiley, Chichester, 2005. 12 G. Turrell and J. Corset (Eds.), Raman Microscopy: Developments and Applications, Academic Press, London, 1996. 13 R.L. McCreery, Raman Spectroscopy for Chemical Analysis, Wiley, New York, 2000. 14 R. Tabaksblat, R.J. Meier and B.J. Kip, Appl. Spectrosc., 46 (1992) 60–68. 15 K.P.J. Williams, G.D. Pitt, D.N. Batchelder and B.J. Kip, Appl. Spectrosc., 48 (1994) 232–235. 16 N.J. Everall, Appl. Spectrosc., 54 (2000) 773–782. 17 N.J. Everall, Appl. Spectrosc., 54 (2000) 1515–1520. 18 A. Gupper, Doctoral Thesis: Enhanced Applications of Microscopic Characterisation Techniques in Materials Science, Graz University of Technology, 2003. 19 L. Markwort, B. Kip and B. Roussel, Appl. Spectrosc., 49 (1995) 1411–1430.
Spatial Imaging/Heterogeneity
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
559
G.J. Puppels, M. Grond and J. Greve, Appl. Spectrosc., 47 (1993) 1256–1267. N.M. Sijtsema, S.D. Wouters, C.J. De Grauw, C. Otto and J. Greve, Appl. Spectrosc., 52 (1998) 348. P.J. Treado, I.W. Levin and E.N. Lewis, Appl. Spectrosc., 46 (1992) 1211. H.T. Skinner, T.F. Cooney, S.K. Sharma and S.M. Angel, Appl. Spectrosc., 50 (1996) 1007. H.R. Morris, C.C. Hoyt, P. Miller and P.J. Treado, Appl. Spectrosc., 50 (1996) 805. P.J. Treado and M.D. Morris, Appl. Spectrosc., 44 (1990) 1. P.J. Treado, A. Govil, M.D. Morris, K.D. Sternittzke and R.L. McCreery, Appl. Spectrosc., 44 (1990) 1270. K.-L.K. Liu, L.-H. Chen, R.-S. Sheng and M.D. Morris, Appl. Spectrosc., 45 (1991) 1717. H. Suto, Infrared Phys. Technol., 38 (1997) 261. M.P. Nelson, W.C. Bell, M.L. McLester and M.L. Myrick, Appl. Spectrosc., 52 (1998) 179. J. Ma and D. Ben-Amotz, Appl. Spectrosc., 51 (1997) 1845. A.D. Gift, J. Ma, K.S. Haber, B.L. McClain and D. Ben-Amotz, J. Raman Spectrosc., 30 (1999) 757–765. H.J. Humecki (Ed.), Practical Guide to Infrared Microspectroscopy, Marcel Dekker, New York, 1995. N.J. Harrick, Internal Reflection Spectroscopy, Wiley Interscience, New York, 1967. J.L. Koenig, Microspectroscopic Imaging of Polymers, ACS, 1998. R. Bhargava and I.W. Levin, Spectrochemical Analysis using Infrared Multichannel Detectors, Blackwell Publishing, 2005. A.J. Sommer, L.G. Tisinger, C. Marcott and G.M. Story, Appl. Spectrosc., 55 (2001) 252–256. K.L.A. Chan and S.G. Kazarian, Appl. Spectrosc., 57 (2003) 381–389. J.M. Chalmers and N.J. Everall, Analusis, 28 (2000) 53–64. J.M. Chalmers, N.J. Everall, M.D. Schaeberle, I.W. Levin, E.N. Lewis, L.H. Kidder, J. Wilson and R. Crocombe, Vib. Spectrosc., 30 (2002) 43–52. S.G. Kazarian and K.L.A. Chan, Progr. Colloid Polym. Sci., 132 (2006) 1–6. M. Francon, Progress in Microscopy, Pergamon Press, London, 1961. D.N. Stacey, Eur. J. Phys., 15 (1994) 236–242. L. Ha¨ussler, G. Pompe, D. Lehmann and U. Lappan, Macromol. Symp., 164 (2001) 411–420. A. Gupper, P. Wilhelm, G. Kothleitner, K.-J. Eichhorn and G. Pompe, Macromol. Symp., 205 (2004) 171–180. P. Wilhelm, B. Chernev, P. Poelt, G. Kothleitner, K.-J. Eichhorn, G. Pompe, N. Johner and A. Piry, Spectrosc. Europe, 16/2 (2004) 14–19. A. Gupper, P. Wilhelm, M. Schmied and E. Ingolic, Macromol. Symp., 184 (2002) 275–285. A. Gupper, P. Wilhelm, M. Schmied, S.G. Kazarian, K.L.A. Chan and J. ReuXner, Appl. Spectrosc., 56 (2002) 1515–1523. P. Wilhelm, B. Chernev and P. Poelt, Macromol. Symp., 230 (2005) 105–109. E.N. Lewis, J. Schoppelrei and E. Lee, Near-infrared Imaging and the PAT Initiative, www.spectroscopyonline.com. Application Notes — www.spectraldimensions.com, Malvern Instruments GmbH. G. Reich, Adv. Drug Deliv. Rev., 57 (2005) 1109–1143. C. Tran, Fresenius J. Anal. Chem., 369 (2001) 313–319. F.W. Koehler IV, E. Lee, L.H. Kidder and E.N. Lewis, Spectrosc. Europe, 14(3) (2002) 12–19. A. Piednoir, C. Licoppe and F. Creuzet, Opt. Commun., 129 (1996) 414–422. A. Lahrech, R. Bachelot, P. Gleyzes and A.C. Boccara, Appl. Phys. Lett., 71 (1997) 575–577. A. Lahrech, R. Bachelot, P. Gleyzes and A.C. Boccara, Opt. Lett., 21 (1996) 1315–1317. M.K. Hong, S. Erramilli, P. Huie, G. James and A. Jeung, Proc. SPIE-Int. Soc. Opt. Eng., 2863 (1996) 54–63. S. Webster, D.N. Batchelder and D.A. Smith, Appl. Phys. Lett., 72 (1998) 1478–1480. C.L. Jahncke, H.D. Hallen and M.A. Paesler, J. Raman Spectrosc., 27 (1996) 579–586. D. Zeisel, S. Nettesheim, B. Dutoid and R. Zenobi, Appl. Phys. Lett., 68(18) (1996) 2491–2492. D. Richards, Phil. Trans. R. Soc. Lond. A, 361 (2003) 2843–2857. L.A. Bottomley, Anal. Chem., 70 (1998) 425R–475R. A. Hartschuh, E.J. Sa´nchez, X.S. Xie and L. Novotny, Phys. Rev. Lett., 90 (2003) 095503. N. Anderson, A. Hartschuh and L. Novotny, Mater. Today, 8 (2005) 50.
560
Peter Wilhelm and Boril Chernev
65 D. Vobornik, PhD thesis: Scanning near-field Infrared Microscopy and Spectromicroscopy Applied to Nano-systems and Cells. Lausanne, 2005. 66 J. Sahlin and N. Peppas, J. Appl. Polym. Sci., 63 (1997) 103–110. 67 C.A. Michaels, L.J. Richter, R.R. Cavanagh and S.J. Stranick, Proc. SPIE, 4098 (2000) 102–109. 68 T. Koshi and M. Kudo, Appl. Surf. Sci., 203–204 (2003) 818–824. 69 B. Hagenhoff, Mikrochim. Akta, 132 (2000) 259–271. 70 P. Fardim and B. Holmbom, Appl. Surf. Sci., 249 (2005) 393–407. 71 B. Tyler, Appl. Surf. Sci., 203–204 (2003) 825–831. 72 S.J. Pachuta, Appl. Surf. Sci., 231–232 (2004) 217–223. 73 W. Kuhn, P. Barth and S. Hafner, Macromolecules, 27 (1994) 5773–5779. 74 L. Ciobanu, D.A. Seeber and C.H. Pennington, J. Magn. Res., 158 (2002) 178–182. 75 M. Drescher, Aust. J. Chem., 58 (2005) 26–28. 76 The National Biomedical Research Center for Advanced ESR Technology (ACERT), http://www.acert.cornell.edu/index_files/acert_highlight_imaging_3.htm 77 J. Dahm, V. Macho, G.G. Maresch and H.W. Spiess, Mol. Phys., 74(3) (1991) 591–598. 78 Z. Veksli, M. Andreis and B. Rakvin, Prog. Polym. Sci., 25(7) (2000) 949–986. 79 W. Yun, S.T. Prant, R.M. Miller, Z. Cai, D.B. Hunter, A.G. Jarstfer, A.M. Kemner, B. Lai, H.-R. Lee, D.G. Legnini, W. Rodrigues and C.I. Smith, J. Synchrotron. Rad., 5 (1998) 1390–1395. 80 E.J. Samuelsen, T. Helle, P.J. Houen, O.W. Gregersen and C. Raven, International Paper Physics Conference, pp. 307–312, 1999. 81 A.P. Hithcock, J. Synchrotron. Rad., 8 (2001) 66–71. 82 B.M. Patterson and G.J. Havrilla, Appl. Spectrosc., 60(5) (2006) 471–478. 83 F. Clarke, A. Whitley, S. Mamedov, F. Adar, N. Lewis and E. Lee, A comparison of Raman and EDXRF chemical imaging for use in formulation process development and quality control, Newsletters, Raman Update (Horiba Jobin Yvon), Spring, 2005. 84 D. Wegrzynek, A. Markowicz, S. Bamford, E. Chinea-Cano and M. Bogovac, Phys. Res. B, 231 (2005) 176–182. 85 D.W. Ball, Spectroscopy, 18(11) (2003) 36–37. 86 U. Vohrer, D. Hegemann, G. Oehr and H. Brunner, Vakuum in Forschung and Praxis Nr., 2 (2000) 118–121. 87 J.J. Schmidt, Jr., J.A. Gardella and L. Salvati, Macromolecules, 22 (1989) 4489–4495. 88 R.D. Short, A.P. Ameen, S.T. Jackson, D.J. Pawson, L. O’Toole and A.J. Ward, Vacuum, 44(11–12) (1993) 1143–1160. 89 M.D. Duca, C.L. Plosceanu and T. Pop, J. Appl. Polym. Sci., 67 (1998) 2125. 90 L.A. Pesin, E.M. Baitinger, Y.P. Kudryavtsev and S.E. Evsyukov, Appl. Phys. A: Mater. Sci. & Proc., 66 (1998) 469. 91 J.E. Flughum, J. Electr. Spectrosc. Rel. Phenom., 100(1) (1999) 331–355. 92 K. Artyushkova and J.E. Fulghum, Surf. Interface Anal., 22 (2002) 185–195. 93 K. Artyushkova, B. Wall, J. Koenig and J.E. Fulghum, Appl. Spectrosc., 54 (2000) 1549–1558. 94 A.P. Pijpers and R.J. Meier, Chem. Soc. Rev., 28 (1999) 233–238. 95 J.D. Winefordner, I.B. Gornushkin, D. Pappas, O.I. Matveev and B.W. Smith, J. Anal. At. Spectrom., 9 (2000) 1161–1189. 96 O.I. Matveev, B.W. Smith and J.D. Winefordner, Appl. Opt., 36(34) (1997) 8833–8843.
CHAPT ER
14 Additive Analysis John Sidwell
Contents
1. Introduction 2. Analytical Techniques for Additive Analysis 2.1 Atomic absorption spectroscopy (AAS) 2.2 Differential scanning calorimetry (DSC) 2.3 Gas chromatography (GC) and with mass spectrometry (GC-MS) 2.4 Infrared spectroscopy (Fourier transform infrared (FTIR) spectroscopy) 2.5 High performance liquid chromatography and with mass spectrometry (LC-MS) 2.6 Plasma emission spectroscopy 2.7 Scanning electron microscopy with elemental X-ray analysis 2.8 Thermogravimetric analysis (TGA) 2.9 X-ray fluorescence spectroscopy 3. Analysis of Specific Additives 3.1 Antiblock additives 3.2 Antifogging agents 3.3 Antimicrobial agents 3.4 Antioxidants 3.5 Antiozonants 3.6 Antistatic agents 3.7 Blowing agents 3.8 Cross-linking agents and cure accelerators (rubber) 3.9 Fillers 3.10 Flame-retardants 3.11 Impact modifiers 3.12 Lubricants and slip additives 3.13 Metal deactivators 3.14 Nucleating agents 3.15 Pigments and dyes 3.16 Plasticisers 3.17 Surfactants 3.18 UV stabilisers (light stabilisers) 3.19 Monomers: Residual monomers
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00414-5
562 563 563 565 565 567 570 571 571 572 573 573 573 573 574 574 582 582 584 585 588 588 588 588 589 589 591 592 593 594 594
r 2008 Elsevier B.V. All rights reserved.
561
562
John Sidwell
3.20 Reaction products of polymerisation and cure 3.21 Solvents 4. Future Developments in Analytical Methodology References
594 599 603 605
1. INTRODUCTION Polymeric products used commercially will invariably contain a range of additives incorporated to achieve a specific technical function (see Chapter 3). For example, lubricants may be included in thermoplastic materials to control viscosity during extrusion. Bulk additives such as plasticisers may be used to give flexibility. Reinforcing fillers can be employed to give stiffness and rigidity or to reduce the cost. Antioxidants and stabilisers are likely to be added to ensure that the product can be processed without degradation and also be protected against oxidative or free radical degradation during use. In addition, additives such as initiators, chain stoppers, surfactants, etc., are often required to aid and control polymerisation and detectable residues of these may be present in products. Detailed chemical analysis of additives and their reaction or breakdown products involves the application of a variety of chromatographic, spectroscopic or other techniques [1–2]. Selection of additives depends on end-use requirements and for certain types of products, for example, those used in contact with food or medical materials, they are subject to regulatory control [3–4]. In this chapter, the main analytical techniques and the methods currently employed in industrial and research laboratories for the analysis of important classes of additives are reviewed. The use of both gas chromatographic and liquid chromatographic methods coupled with mass spectrometry features prominently. Such methodology enables the sensitive and specific detection of many types of organic additives in polymeric materials to parts per billion (mg/kg) levels. Much of the development of these methods has been undertaken as part of research into the migration or extraction of species from food-contact and medical materials [5–7]. This chapter also includes some discussion on the analysis of residual monomers and solvents. Table 1 summarises the major classes of additives used with polymeric materials and provides some typical examples of the types of chemical species employed. For the analysis of organic additives in polymeric materials, in most cases, prior extraction will be necessary. Depending on the nature of the additive, many different approaches are employed. These include soxhlet extraction with organic solvent or aqueous media, total sample dissolution followed by selective precipitation of the polymer leaving the additive in solution, assisted extraction using pressurised systems, ultrasonic agitation and the use of supercritical fluids. In trace analysis, solid phase extraction (SPME) from solution or solvent partition may be required to increase the analyte concentration.
Additive Analysis
Table 1
563
Common additives
Additive type
Typical examples
Antiblocking agents Antifogging agents Antimicrobials
Silica, talc Glycerol esters, surfactants Silver containing zeolites, 2,4,4u-trichloro-2uhydroxydiphenyl ether Antioxidants Hindered phenols, phosphites, thioesters Antiozonants Phenylene diamines, hydrocarbon waxes Antistatic agents Ethoxylated amines, lauric acid diethanolamide, glycerol monostearate Blowing agents Azo compounds, hydrazine derivatives, bicarbonates/carbonates Cross-linking agents and Peroxides, thiurams, dithiocarbamates, cure accelerators (rubber) sulphenamides Fillers Silica and silicates, calcium carbonate Flame retardants Antimony trioxide with chlorinated or brominated organics, hydrated alumina Impact modifiers Polybutadiene rubber, methacrylate–butadiene– styrene terpolymers, acrylic rubber Light/UV stabilisers Benzophenones, benzotriazoles, hindered amines Lubricants and slip Erucamide, oleamide, calcium stearate, zinc additives stearate, stearic acid, fluorinated compounds, silicones Metal deactivators N,Nu-bis(3-(3,5-di-tert-butyl-4hydroxyphenyl)propionyl) hydrazide Nucleating/clarifying Sorbitol esters agents Pigments and dyes Titanium dioxide, mono and disazo compounds phthalocyanines, anthraquinones Plasticisers Monomeric and polymeric phthalate esters, adipate and citrate esters Surfactants Alkyl benzene sulfonates, alkyl sulfates
The specific analytical techniques discussed in this chapter and their main applications are detailed in Table 2. Sample homogeneity/heterogeneity may need to be addressed when selecting an analytical technique or designing a test method.
2. ANALYTICAL TECHNIQUES FOR ADDITIVE ANALYSIS 2.1 Atomic absorption spectroscopy (AAS) AAS is used to quantify the concentration of specific elements in solution. In flame atomic absorption, the analyte solution is introduced into the flame
564
John Sidwell
Table 2
Analytical techniques and their main applications
Analytical technique
Applications
Atomic absorption spectroscopy (AAS) Differential scanning calorimetry (DSC) Gas chromatography (GC) and with mass spectrometry (GC-MS) Fourier transform infrared spectroscopy (FTIR)
Determination of trace metals and other elements in aqueous or organic solvent extract solutions Identification of polymeric additives by their melting point Examination of volatile and semi-volatile species such as solvents, monomers, plasticisers, etc.
High performance liquid chromatography (HPLC) and with mass spectrometry (LC-MS) Plasma emission spectroscopy (PES) Scanning electron microscopy (SEM) with elemental X-ray analysis Thermogravimetric analysis (TGA) X-ray fluorescence spectroscopy (XRF)
Fingerprinting materials, identification of bulk additives such as plasticisers and fillers. Non-destructive examination of samples Examination of non-volatile material particularly including polar, ionisable and ionic substances such as antioxidants, stabilisers and curatives Multi-element screening of low level and trace inorganic elements Visualising and detecting different elements in particulate additives or contaminants Examination of the bulk composition of polymeric materials Non-destructive screening and determination of inorganic materials; for example, flame retardants
(air/acetylene or nitrous oxide/acetylene), where it vaporises. Element atoms in their ground state are excited to a higher electronic level and are detected by absorption of incident radiation at a specific frequency relating to the difference in energy between the two energy levels. Conventional AAS measures one element at a time. Multi-element lamps are available that can enable measurement in solution of 2–6 specific elements simultaneously. Elemental analysis is undertaken after dissolution in an organic solvent, after oxidative wet digestion, after dry-ashing or in the solid state. Matrix effects can be important in quantitative work. Other atomisation procedures are used such as graphite furnace and hydride generation to maximise sensitivity, particularly where the available test solution volume is low or where sub ppm sensitivity is required. Typical applications include: a)
Quantification of organotin stabilisers (as tin) in rigid poly(vinyl chloride) (PVC) formulations.
Additive Analysis
b) c)
565
Examination of copper, manganese and iron (which can catalyse degradation) in natural rubber. Determination of toxic elements in children’s toys, for example, cadmium, lead, mercury, arsenic and chromium.
The AAS technique is in competition with plasma emission spectroscopy (Section 2.6) for the elemental analysis of plastic, rubber and other polymeric materials.
2.2 Differential scanning calorimetry (DSC) The DSC technique enables crystalline materials to be characterised by their melting point. Additives that come into this category include hydrocarbon waxes and poly(tetrafluoroethylene) (PFTE) lubricant. The presence of PTFE in low friction acetal mouldings can be established from the detection of the PTFE melting endotherm at 3201C.
2.3 Gas chromatography (GC) and with mass spectrometry (GC-MS) Gas chromatographic methods are used for the analysis of organic additives extracted from polymers with solvents and other liquid media or evolved by heating. Fused silica capillary columns of various internal bores and of lengths in the range 25 to 50 m are mainly employed for analytical separations. A variety of polar and non-polar column types are available including those open tubular types with simple wall coatings (WCOT), those with coatings dispersed on porous solid-supports to increase adsorbent surface area (SCOT) and porous layer open tubular (PLOT) columns. Important stationary phases include polyethylene glycol, dimethylpolysiloxane and different siloxane copolymers. Various sample introduction procedures are employed including: a) b) c) d) e)
direct injection of liquid media, static headspace, dynamic headspace, cold-on column, split and splitless.
The range of detectors for GC includes: a) b) c)
d) e) f)
the flame ionisation detector (FID) which is widely employed, the nitrogen–phosphorus detector (NPD) used to detect the nitrogen containing monomer acrylonitrile, the thermal conductivity detector (TCD), which is particularly used to detect gases such as carbon dioxide and oxygen but is of limited application to additives, the flame photometric detector (FPD), which detects chemiluminescence, the electron capture detector (ECD) used to detect chlorine-containing organics with high sensitivity, the mass spectrometer used to aid positive identifications.
566
John Sidwell
Multidimensional GC with time of flight MS (ToF-MS) is increasingly being employed to examine complex mixtures. In this technique non-polar and polar GC stationary phases connected by a thermal modulator enable increased resolution of GC peaks. The fast scanning made possible by the ToF measuring system leads to many data points across peaks and the possibility of deconvolution of complex overlapping peaks. Figure 1 highlights the separation of a mixture of different polarity GC standards known as the ‘‘Grob mix’’ commonly used to test the efficiency of columns. Figure 2 shows the linear representation highlighting the closeness of elution time if only a single column had been employed. The identity of the mix chemicals and their retention times are given in Table 3. The instrument used to generate the data shown in Figures 1 and 2 (LECO Pegasus III GC GC-ToF-MS) has a modulator at the end of the first 30 m 0.25 mm non-polar column (HP-5MS, 0.25 mm film thickness). As compounds elute from this column, the modulator concentrates them over a short period to focus them and then sends them down the second, shorter and narrower 2 m 0.10 mm, polar column (BPX-50, 0.10 mm film thickness) situated in its own oven compartment within the main oven. This operation is repeated throughout the analytical run. Having the two columns coupled in this way allows compounds to be separated by volatility on the first analytical column and by polarity on the second column. Hence for complex mixtures, peaks with a similar (or identical) retention on the first column can be separated by the second column. Non-polar compounds emerge before polar components.
Figure 1 Separation of the standard ‘‘Grob mix’’ using two-dimensional GC/MS. (See Color Plate Section at the end of this book.)
Additive Analysis
567
Figure 2 Linear representation of the total ion chromatogram (TIC) of the ‘‘Grob mix’’. Table 3
a
Species present in the ‘‘Grob mix’’ and their retention times/concentration
Retention timea (s)
Peak assignment
Concentration (mg/kg)
404.99, 3.80 712.96, 1.97 796.95, 2.35 828.95, 1.94 836.95, 2.34 840.94, 2.82 848.94, 2.34 904.94, 3.02 1052.9, 2.20 1140.9, 2.18 1144.9, 2.34 1220.9, 2.18
2,3-Butanediol Decane 1-Octanol Undecane Nonanal Phenol, 2,6-dimethylHexanoic acid, 2-ethylBenzenamine, 3,5-dimethylDecanoic acid, methyl ester Undecanoic acid, methyl ester Cyclohexanamine, N-cyclohexylDodecanoic acid, methyl ester
10.6 5.6 7.2 5.8 7.8 6.4 7.6 6.4 8.2 8.4 6.2 8.2
The two retention times relate to the non-polar and polar columns, respectively, see text.
A chromatogram obtained for the examination of acetone extractables from an ethylene propylene-based rubber is shown in Figure 3. Excellent separation of the main hydrocarbon components from polar compounding ingredients and curative breakdown products is observed.
2.4 Infrared spectroscopy (Fourier transform infrared (FTIR) spectroscopy) Infrared (IR) spectroscopy is commonly used to ‘‘fingerprint’’ materials by comparing the IR absorption spectra of unknowns against reference standards.
568
John Sidwell
Figure 3 Examination of the acetone extract from an EPDM (ethylene propylene diene monomer) rubber using two-dimensional gas chromatography. (See Color Plate Section at the end of this book.)
The frequencies of absorption bands present gives diagnostic information on the nature of functional groups in materials as well as information from any observed frequency shifts on aspects such as hydrogen bonding and crystallinity. In many cases, spectra can be recorded non-destructively using either reflection or transmission procedures. IR spectra of small samples can also be obtained through microscopes (IR microspectrometry). Chalmers and Dent [8] discuss the theory and practice of IR spectroscopy in their book on industrial analysis with vibrational spectroscopy. Standard spectra of additives for polymeric materials include the major collection by Hummel and Scholl [9]. Figure 4 shows a reflection IR spectrum of the Dyneont polymer processing additive Dynamar FX 5920A, a fluorpolymer for melt fracture elimination in blown polyethylene film applications. The spectrum was recorded of the additive powder using a Specac ‘‘Golden Gatet ’’ internal reflection attachment fitted with a diamond prism. This type of accessory enables spectra of all types of liquid and solid samples to be obtained very quickly and negates the need to prepare for example potassium bromide disks. This processing additive is based on polyethylene oxide (60–70%) and vinylidene fluoride-hexafluoropropylene polymer (25–35%). Some talc and calcium carbonate are also present. Diagnostic absorption bands associated with all of the components of the additive are detectable in the spectrum. For the IR spectroscopic identification of additives in polymeric products, in many cases it is necessary to first isolate the additive either by solvent extraction, chromatographic separation or removal of interfering constituents by ashing, etc.
569
Additive Analysis
To identify plasticisers in simple systems, often an IR spectrum of a methanol or acetone extract (after evaporation of solvent) will enable the positive identification of plasticiser type. For more complex systems it is necessary to initially separate the extractable fraction from the sample on for example a molecular weight basis (molecular size in solution). Figure 5 shows the separation of the plasticiser components present in a PVC-based cling film. The sample was first dissolved in tetrahydrofuran and then the components present separated by size exclusion chromatography (SEC) using mixed bed-E columns (Polymer Laboratories) and tetrahydrofuran eluting solvent. IR spectra of the separated components were then obtained using ‘‘LC-Transforms’’ (Lab Connections) equipment. Components as they elute from
90 80
% Reflectance
70 60 50 40 30 20 4000
3500
3000
2500
2000
1500
1000
500
Wavenumber/cm-1
Figure 4 Infrared spectrum of Dynamar FX 5920A polymer processing additive.
0.8
dw/dlogM
0.6 0.4 0.2 0.0 2
3
4 logM
5
6
Figure 5 Separation of the plasticisers present in PVC cling film by size exclusion chromatography. (Peaks left to right, identified by their infrared spectra, obtained using LC-Transforms equipment, as DEHA, ESBO and PVC.)
570
John Sidwell
the SEC column were cast onto a rotating reflective germanium disk and examined by IR spectroscopy. From the spectra obtained, the two low molecular weight plasticisers were identified as being diethyl hexyl adipate (DEHA) and epoxidised soya bean oil (ESBO). Separation of these plasticisers from the bulk PVC component was achieved.
2.5 High performance liquid chromatography and with mass spectrometry (LC-MS) Many organic additives can be analysed using the technique of high performance liquid chromatography (HPLC), particularly using MS for positive identification. HPLC methods have now largely superseded thin layer chromatography (TLC)based procedures. A range of MS ionisation techniques are available. Atmospheric pressure chemical ionisation (APCI) and electrospray ionisation (ESI) are becoming the methods of choice for the analysis of low molecular weight additives of mass/ charge (m/z) ratio o3,000. With APCI, the LC column eluent is nebulised in a heated vaporiser. Once vaporised, the plasma of eluent and sample components enters the APCI source where it encounters electrons emitted from the tip of a corona discharge needle. The eluent molecules are ionised and act as the reagent gas in a chemical ionisation process, transferring charge to the analyte. In the positive mode: (Solvent + H)+ + Analyte - Solvent + (Analyte + H)+ and, in the negative mode: (SolventH) + Analyte - Solvent + (AnalyteH). Protonic solvents such as methanol or acetonitrile are commonly employed, often with the addition of formic or acetic acid or bases such as hexylamine, to aid gas phase ionisation. APCI is suitable for the ionisation of small molecules that are polar to non polar in nature particularly those containing heteroatoms. Samples that are ionic/charged in solution or are very thermally unstable or photosensitive are better suited to ESI where ionisation is achieved in solution, prior to detection using the mass analyser. In LC-MS, specific ionisation conditions can be required for different types of species. This means that in LC-MS studies on extractable additives, it is necessary to use a range of experimental conditions to cover detection of all types of potential species. Depending on instrument type, it is also possible to isolate ions in complex matrices and obtain positive identifications by further unique fragmentation of these ions (by MS-MS or MSn). Quantitative methods based on this secondary ionisation can be employed. The mass accuracy of LC-MS detection systems continues to improve. Accurate mass measurement improves the certainty of identification. Advanced systems are typically offering 1–2 ppm (mass dependent) mass accuracy. Other types of atmospheric pressure ionisation detectors are available including APPI (photon ionisation) and MALDI (matrix-assisted laser desorption ionisation). More conventional detection systems for LC include UV absorption, fluorescence and evaporative light scattering. Developments in column packings,
Additive Analysis
571
particularly the introduction of packings of particle size o5 mm with their associated increase in separation efficiency, are now enabling analytical run times to be speeded up. Equivalent separation resolving power is retained.
2.6 Plasma emission spectroscopy Inductively coupled plasma atomic emission spectrometry (ICP-AES) is used to screen polymers, liquids and solvent extracts for residual metal atoms (catalysts, fillers, etc.). The technique can provide rapid multi-component screening of elements in solution over a wide concentration range (0.1–1,000 mg/ml). The principle of ICP-AES is that atoms (or sometimes ions) are thermally excited, in a plasma torch, to higher energy levels, these atoms or ions then relax back to lower electronic energy levels by emitting radiation in the UV-visible region. The emitted radiation is detected and used to determine which elements are present, and their concentration. Analysis of organometallic and inorganic additives, based on the ICP-AES determination of specific metal ions, is routinely undertaken.
2.7 Scanning electron microscopy with elemental X-ray analysis Additive distribution on surfaces can be studied using a variety of techniques. For visualisation, the technique of scanning electron microscopy (SEM) is preferred. The selected area is illuminated with a beam of electrons. Surface topography is viewed as a secondary electron or back-scattered electron image. An X-ray analyser can provide elemental information on selected surface features. Elemental mapping is possible. The energy (keV) of liberated X-rays allows specific identification of elements present. The depth of penetration of the X-rays depends on incident voltage and can be B1 mm. At low voltages it is possible to examine carbon and oxygen concentrations. Figure 6 shows a typical energy dispersive analysis (EDA) trace.
Figure 6 Elements detected in a contaminant material by SEM/EDA analysis.
572
John Sidwell
2.8 Thermogravimetric analysis (TGA) The technique of thermogravimetry is used to study the bulk composition of materials (i.e., levels of major components present such as plasticisers, polymer and fillers, etc.). For examining bulk composition, small amounts of sample (B10 mg) are typically heated from ambient temperatures to 5501C in an inert flowing atmosphere, cooled to 3001C and further heated to B9001C in flowing air. Percentage weight loss and derivative weight loss (rate of change) are recorded throughout. For homogeneous samples, quantitative compositional data can be obtained. For rubber materials, ISO standards are available, for example, ISO 9924-1:2000 — Rubber and rubber products-Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 1: Butadiene, ethylene-propylene copolymer and terpolymer, isobutene-isoprene, isoprene and styrenebutadiene rubbers, and ISO 9924-2:2000 — Rubber and rubber products-Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 2: Acrylonitrile-butadiene and halobutyl rubbers. Some materials such as PVC give relatively complex TGA traces, which make the quantification of individual components difficult. Figure 7 shows a TGA trace for a PVC compound containing some calcium carbonate filler. Weight losses 1 and 2 relate to a two-stage decomposition of the PVC polymer. This produces a carbonaceous residue, which is oxidised in air as part of weight loss 3. Some of the hydrochloric acid liberated during the thermal decomposition of the PVC reacts with part of the calcium carbonate filler. However, weight loss 4 mainly relates to the decomposition of unreacted calcium carbonate to calcium oxide. Therefore, for PVC, only approximate indications of filler content can be obtained by thermogravimetry. The use of X-ray fluorescence (XRF) with appropriate standards can give better quantitative data.
Figure 7 TGA data for a rigid PVC compound showing % weight loss and derivative (rate of) weight loss traces.
Additive Analysis
573
2.9 X-ray fluorescence spectroscopy In the technique of XRF, samples are bombarded with X-rays and the intensity of X-rays emitted from the sample determined as a function of energy or wavelength. XRF is a non-destructive technique applicable to a wide range of elements of atomic weight greater than boron. Standards in the same matrix are required for quantitative determinations, for example, quantifying inorganic fillers. It is common to ash samples prior to XRF analysis, but it is important to be aware of the possibility that some inorganics may be volatile at ashing temperatures, for example, lead chloride. The XRF technique is used to examine PVC stabilisers and fluorocarbon rubber inorganic curatives, etc. The technique is finding increasing use for the screening of potential recyclate materials for the presence of halogenated flame-retardants and toxic heavy metals.
3. ANALYSIS OF SPECIFIC ADDITIVES 3.1 Antiblock additives Antiblock additives are often incorporated into packaging films to prevent them sticking together. Their effectiveness relates directly to the roughness they impart on a film surface while minimising loss in optical properties. They are often used in association with slip additives such as erucamide. Common antiblock additives include crystalline silica, diatomaceous earth and talc (magnesium silicate). Antiblock additives can be seen on the surface of films using optical microscopy or SEM. Identification can normally be achieved with internal reflection IR spectroscopy (e.g., with a germanium crystal to minimise sampling depth) or using an X-ray attachment with the electron microscope. Microcrystalline waxes can also act as an antiblock and can provide some processing benefits. Polymeric antiblocks based on organic particles have also recently been introduced.
3.2 Antifogging agents Antifogging (antimisting) agents are employed to reduce the build-up of water droplets on the surface of transparent packaging films employed, for example, as salad wraps or for agricultural films. They are normally incorporated into the plastic prior to extrusion. After extrusion, antifogging additives will migrate to the surface and increase the surface tension, so that when the surface tension of the polymer is equal to that of water, any water droplets will spread into a continuous layer and not be visible. In many cases, three layer ethylene vinyl acetate (EVA)-based films are employed with the middle layer containing a ‘‘reservoir’’ of antifogging additive. The presence of such additives on the surface of films can normally be established using reflection IR spectroscopy.
574
John Sidwell
3.3 Antimicrobial agents Antimicrobial additives can be used in polymeric materials to prevent or reduce the growth of bacteria and other organisms. A common antimicrobial agent is 2,4,4u-trichloro-2u-hydroxydiphenyl ether also known as triclosan. Its presence can be detected using combined GC/MS (Figures 8 and 9).
3.4 Antioxidants A wide variety of methodologies have been employed for the analysis of antioxidants in polymers and some standard methods are available. For highdensity polyethylene ASTM method D5524 (ASTM International) — Determination of phenolic antioxidants in high-density polyethylene, describes a method whereby the sample is ground to a small particle size and then extracted by refluxing with cyclohexane. The cyclohexane extract is then examined by reversephase HPLC with UV detection. For rubber, a thin layer chromatographic (TLC) method is available; ISO 4645:1984 Rubber and rubber products — Guide to the identification of antidegradants — TLC methods. Sidwell and Zondervan [10] used LC-MS with APCI detection for the identification and quantification of extractable antioxidants from food-contact plastic materials. Identification is based on the presence of the molecular ion (M + H)+, (MH), other key ions or on further ion breakdown (MSn) transitions. The following antioxidant/stabiliser types were examined: hindered phenols,
80000 70000 60000 50000 40000 30000 20000 10000 0 4
6
8
10
12
14
16
18
20
22
24
26
28
Time/minutes
Figure 8 GC-MS detection of 2,4,4u-trichloro-2u-hydroxydiphenyl ether in the isooctane extract from a food container, from its mass spectrum.
575
Additive Analysis
(A) Abundance
218
Scan 9.97 min 8000 6000 4000 2000 0
51
63 75 87 99
40
146
115
28 20
288
60
80
133
162
175
252
189 201
236
100 120 140 160 180 200 220 240 260 280 m/z
(B) Abundance
288 Triclosan
8000 6000 4000 2000 0
79 40
60
146
114
51 63
20
218
80
98
126
161
189
252
100 120 140 160 180 200 220 240 260 280 m/z
Figure 9 (A) electron impact mass spectrum of the peak at 9.97 min (see Figure 8); (B) MS of a reference standard of triclosan.
other phenolics, phosphites and phosphonites, thioester and other sulfurcontaining non-phenolic stabilisers. Many of these species can also be detected by ESI. Identifying ions are detailed in Tables 4–7. The use of specific ion monitoring, together with additional confirmatory ionisation, enabled the positive detection of the analyte of interest. The limit of detection was typically in the range 0.01–0.001 mg/kg in solution, for the antioxidants examined. Figures 10 and 11 show the structure of the hindered phenolic antioxidant Irganoxs 1010 (Ciba) and its negative ion APCI mass spectra, respectively. Separation was achieved under the following LC conditions: Column: Aqua C18 (Phenomenex) 3 mm, 150 2.00 mm, 15% carbon loading, proprietary end capping. Column Temp: 501C. Injection volume: 5 ml. Flow-Rate: 0.5 ml/min. Pump Sequence: A. 75/25 methanol/water (v/v) B. 50/50 ethyl acetate/acetonitrile (v/v) 90% to 0% A, via linear gradient over 25 min, held for 5 min. Hsiao et al. [11] have studied the use of MALDI ionisation for the detection of antioxidants and hindered amine light stabilisers (HALS) in polyethylene extracts. Using 2,5-dihydroxybenzoic acid as matrix, diagnostic spectra were obtained on standards, but the presence of soluble low molecular weight polyethylene in extract solutions caused some problems with ionisation suppression. It is also possible to separate and detect antioxidants by SEC. This can be useful for the antioxidants that are strongly retained on C18 HLPC columns such as Irganox PS802 (thiodipropionic acid, dioctadecyl ester). Figure 12 shows the separation of Irganox PS802 (peak eluting first) from Irganox 1076, using a separation column suitable for the separation of
576 John Sidwell
Table 4 Hindered phenol antioxidants PM Ref.
CAS no
Trade name Chemical name
PM 38800
32687-78-8
Irganox MD1024
PM 39060
35958-30-6
PM 40000
00991-84-4
Irganox 565
PM PM PM PM
25013-16-5 128-37-0 04130-42-1 23128-74-7
BHA BHT
40720 46640 46720 59120
Irganox 1098
N,Nu-bis(3-(3,5-di-tert-butyl-4hydroxyphenyl)propionyl) hydrazide 1,1-Bis(2-hydroxy-3,5-di-tertbutylphenyl)ethane 2,4-Bis(octylmercapto)-6(4-hydroxy-3,5-di-tertbutylanilino)-1,3,5-triazine Tert-butyl-4-hydroxyanisole 2,6-Di-tert-butyl-p-cresol 2,6-di-tert-butyl-4-ethylphenol 1,6-Hexamethylenebis(3-(3,5-ditert-butyl-4hydroxyphenyl)propionamide)
Exact mass
BRetent. time (mins)
Primary ion for quantification +/ 0.1 m/z (ve APCI)
Confirmatory ions MS2 or other quantification ions +/ 0.1 m/z ve APCI
552.39
5.2
551.3
333.2
438.35
12.1
437.3
205.1
588.39
19.8
587.3
530.3, 474.2, 244.1
180.12 220.18 234.20 636.49
6.0 5.2 6.1 5.9
179.0 219.2 233.2 635.6
164.0 202.9 217.1 417.3, 375.3, 579.4
PM 59200
35074-77-2
PM 68320
02082-79-3
PM 71680
Irganox 259
Irganox 1076 006683-19-8 Irganox 1010
PM 92880
41484-35-9
PM 95200
001709-70-2 Irganox 1330 27676-62-6 Irganox 3114
PM 95360
Irganox 1035
1,6-Hexamethylene bis(3-(3,5di-tert-butyl-4hydroxyphenyl)propionate) Octadecyl 3-(3,5-di-tert-butyl-4hydroxyphenyl) propionate Pentaerythritol tetrakis[3-(3,5di-tert-butyl-4hydroxyphenyl)propionate] Thiodiethanol bis(3-(3,5-di-tertbutyl-4-hydroxy phenyl) propionate) 1,3,5-Trimethyl-2,4,6-tris(3,5-di-tertbutyl-4-hydroxybenzyl)benzene 1,3,5-Tris(3,5-di-tert-butyl-4hydroxybenzyl)-1,3,5-triazine2,4,6(1h,3h,5h)-trione
638.45
12.5
637.5
419.2, 377.3
530.47
21.0
529.4
1176.78
18.3
1175.6
527.3, 231.1, 257.1 957.6, 739.4, 915.6
642.40
11.1
641.5
363.2, 423.2, 277.1
774.60
18.7
773.7
717.5, 661.5
783.52
14.3
564.4
346.1
Notes: PM Ref, European Commission substance reference number; CAS no, American Chemical Society, Chemical Abstracts Service (CAS) registry number.
Additive Analysis
577
578
Table 5
Other phenolic antioxidants CAS no
Trade name
Chemical name
Exact mass
BRetent. Primary ion for time (mins) quantification +/ 0.1 m/z (ve APCI)
Confirmatory ions MS2 or other quantification ions +/ 0.1 m/z ve APCI
PM 31520
61167-58-6
Irganox 3052
394.25
8.3
393.2
375.2
PM 40020
110553-27-0 Irganox 1520
424.28
15.3
423.2
145.0
PM 66400
00088-24-4
368.27
8.9
367.2
177.0
PM 66480
00119-47-1
340.24
7.1
339.2
163
PM 92800
00096-69-5
358.20
4.2
357.2
194.0, 163.2
PM 93520 PM 94400
000059-02-9 Irganox E201 36443-68-2 Irganox 245
430.38 586.37
17.7 4
429.3 585.3
420.3, 412.3 367.2, 409.2
PM 95280
40601-76-1
Cyanox 1790
699.42
11.2
698.3
508.3, 318.1
PM 95600
01843-03-4
Topanol CA
Acrylic acid, 2-tert-butyl-6(3-tert-butyl-2-hydroxy-5methylbenzyl)-4-methylphenyl ester 2,4-Bis(octylthiomethyl)6-methylphenol 2,2u-Methylenebis(4-ethyl6-tert-butylphenol) 2,2u-methylenebis(4-methyl6-tert-butylphenol) 4,4u-Thiobis(6-tert-butyl-3methylphenol)) Alpha-tocopherol Triethyleneglycol bis[3(3-tert-butyl-4-hydroxy5methylphenyl) propionate] 1,3,5-Tris(4-tert-butyl-3-hydroxy-2, 6-dimethylbenzyl)-1,3,5-triazine2,4,6(1h,3h,5h)-trione 1,1,3-Tris(2-methyl-4-hydroxy5-tert-butylphenyl) butane
544.39
7.29
543.3
487.3, 337.2, 281.1
Antioxidant 425 Antioxidant 2246 Yoshinox SR
John Sidwell
PM Ref.
Table 6 Phosphites and Phosphonites. (It should be noted that the phosphite and phosphonite classes of stabiliser are particularly reactive and can be prone to decomposition in extraction solvents and food simulants) PM Ref.
CAS no
PM 38820 26741-53-7 PM 38840 154862-43-8 PM 46880 065140-91-2
PM 50080 3806-34-6
PM 74240 031570-04-4
Chemical name
Ultranox Bis(2,4-di-tert-butylphenyl) 626 pentaerythritol diphosphite Bis(-2,4-dicumylphenyl) pentaerythritol-diphosphite Irganox 3,5-Di-tert-butyl-41425 hydroxybenzylphosphonic acid, monoethyl ester, calcium salt Weston 3,9-Bis(octadecyloxy)-2,4,8,10618 tetraoxa-3,9diphosphaspiro[5,5]undecane Irgafos Phosphorous acid, tris(2,4-di168 tert-butylphenyl)ester
Irgafos PEPQ
Tetrakis(2,4-di-tert-butyl-phenyl)4,4u-biphenylylene diphosphonite
Exact mass
BRetent. time (mins)
Primary ion for quantification +/ 0.1 m/z (ve or +ve APCI)
Confirmatory ions MS2 or other quantification ions +/ 0.1 m/z ve APCI
640.33
3.5
205.2 (ve)
3.5
888.39
853.4 (+ve)
694.31
699.4
732.56
733.6 (+ve)
646.45
22.4
Mixed components
Strongly retained eluting after Irganox 1076
473.2 (ve) 205.1 647.3 (+ve) +16 for phosphate oxidation product (ve) Peak 1 877.5 Peak 2 893.5 Peak 3 877.5 Peak 4 861.5 (+ve) Peak 1 611.4 Peak 2 1068.7 Peak 3 1052.7 Peak 4 1038.7
579
Note 1: Best examined with a less aqueous, more organic mobile phase gradient, or isocratic condition.
349.1
Additive Analysis
PM 92560 38613-77-3 Note 1
Trade name
580
Chemical name
SML (mg/kg)
Exact mass
BRetent. time (mins)
Primary ion for quantification +/ 0.1 m/z (ve and +ve APCI)
27458-90-8
Di-tert, dodecyl disulfide
0.05
402.34
Not examined
PM 49840
02500-88-1 Hostanox SE10
Dioctadecyl disulfide
3
570.52
Not examined
PM 93120
00123-28-4 Irganox PS800
5
514.41
00693-36-7 Irganox PS802
5
682.59
Not examined but after Irganox 1076 (Note 1) Not examined but after Irganox 1076 (Note 1)
Not examined
PM 93280
Thiodipropionic acid, didodecyl ester Thiodipropionic acid, dioctadecyl ester
Unlikely to readily ionise. Best examined by GC-MS Unlikely to readily ionise. Best examined by GC-MS 515.4 (+ve)
683.6 (+ve)
Not examined
PM Ref.
CAS no
PM 47540
Trade name
Note 1: Best examined with a less aqueous, more organic mobile phase gradient or isocratic condition.
Confirmatory ions MS2 or other quantification ions +/ 0.1 m/z ve APCI
John Sidwell
Table 7 Thioester and other sulfur-containing non-phenolic stabilisers
Additive Analysis
581
HO
OH
O O
O
O
O O O
O
HO
OH
Figure 10 Chemical structure of Irganox 1010 (mass 1177).
Intensity
1176.0
231.1
Intensity
957.6
739.4 915.6 521.2 389.2 479.3 437.2
200
400
697.4
1175.7
607.3
600
800
1000
1200
m/z
Figure 11 Negative APCI mass spectrum for Irganox 1010 showing (MH) ion at m/z 1,176 and MS2 main diagnostic transition of 1,176 ion - ions at m/z 958, 916 and 739.
582
John Sidwell
RI Chromatogram 100 83 Irganox PS802
Irganox 1076
RI Response
67 50 33 17 0 5.0
9.0
13.0
17.0
21.0
25.0
Retention Volume
Figure 12 Separation of Irganox 1076 and Irganox PS802 by size exclusion chromatography (duplicate solution injections of each antioxidant showing the reproducibility of the technique).
low molecular weight materials (duplicate sample injections). Conditions used were Columns: 2 Plgel mixed bed-E (Polymer Laboratories), 30 cm, 3 mm packing Solvent: chloroform Injection loop: 20 ml Flow-rate: 1.0 ml/min Temperature: 301C Detector: refractive index
3.5 Antiozonants Antiozonant additives are employed with unsaturated rubbers such as natural rubber, nitrile rubber, styrene-butadiene rubber, etc., to minimise the atmospheric ozone degradation reaction. Common antiozonant types include the paraphenylene diamines such as N-(1,3-dimethylbutyl)-Nu-phenyl-p-phenylene diamine (6PPD) and N-isopropyl-Nu phenyl-p-phenylene diamine (IPPD). Both these antioxidants can be identified and quantified using GC- or LC-based techniques.
3.6 Antistatic agents Common antistatic agents for food-contact and medical materials include ethanolamines (ethoxylated amines), ethanolamides, laurylamide and glycerol monostearate.
Additive Analysis
583
7
5
Intensity x107
4
3
2
1
0 2
4
6
8
10
12
Time/min
Figure 13 Detection of 6 ppm (w/v) of a mixed ethoxylated amine by ESI (electrospray) LC-MS. Total ion current (TIC) trace.
The Hostastat FA14 (Clariant) antistatic agent is a mixture of ethoxylated amines varying in alkyl chain length. Figure 13 shows the LC-MS separation of the individual ethoxylated amines in Hostastat FA14 using a C18 bonded column and isocratic elution with a mixture of 35% acetonitrile and 65% of 0.5% formic acid in distilled water. Detection was with positive ESI. The peaks appear in the chromatogram as a series of five main peaks eluting between 0.8 and 12 min. The peaks correspond to alkyl chain lengths of C8, C10, C12, C14 and C16, respectively. The largest peak C12 seen at 6.1 min and with (M + H)+ ¼ 274 has been used for quantification of levels of the antistat in materials. The related synthetic antistat Atmer 163 can be detected and quantified in a similar manner. Extraction from samples using hexane/isopropanol (IPA) 30/70 mixtures is employed. Figure 14 shows separation using an Agilent Ion-Trap SL LC-MS with a Phenomenex Aqua C18 column (150 2 mm) at 451C and 0.5 ml/min. Solvent A was 0.5% formic acid in water and solvent B was acetonitrile. The solvent gradient was taken from 45% B to 70% B over 15 min and held for 5 min. The mass spectrometer was set to scan 280 to 300 m/z, targeting 288 m/z with ESI ionisation. Glycerol monostearate can also be determined by LC-MS. Detection by positive APCI is possible. Figure 15 shows a typical chromatogram for the technical product eluting from a Phenomenex Aqua C18 column with methanol– water gradient (70–100% methanol). The molecular ion (M + H)+ mass spectra of the two main peaks detected are shown in Figures 16 and 17.
584
John Sidwell
Intensity x107
1.0 0.8 0.6 0.4 0.2 0.0 2
4
6
8 Time/min
10
12
14
Intensity
Figure 14 1 ppm Atmer 163 (N,N-bis(2-hydroxyethyl)alkylamine) in 30/70 hexane/IPA.
0 2.5
5
7.5
10
12.5
15
17.5
20
22.5
min
Figure 15 Technical Glycerol monostearate examined by LC-MS with positive APCI.
3.7 Blowing agents Depending on the nature of the blowing agent, it is possible that decomposition products may be present in expanded products. This has been established for the blowing agent azodicarbonamide for which low levels of semicarbazide have been detected in food stored in glass jars sealed with expanded PVC seals [12]. Chemical structures are H2N–CO–N ¼ N–CO–NH2 Azodicarbonamide
H2N–NH–CO–NH2 Semicarbazide
585
100
150
200
250
300
331.3
314.3
Intensity
313.3
Additive Analysis
350
m/z
342.3 359.3
Intensity
341.3
Figure 16 Mass spectrum of component eluting at 9.34 min (see Figure 15). (331.3 ion is the (M + H)+ ion of glycerol monopalmitate.)
100
200
300
400
500
600
m/z
Figure 17 Mass spectrum of component eluting at 10.0 min (see Figure 15). (359.3 ion is the (M + H)+ ion of glycerol monostearate.)
Analytical methods for the detection of residues of semicarbazide use derivatisation with 2-nitrobenzaldehyde and LC-MS detection. Figure 18 shows the positive ESI response for a 1 ppm solution of semicarbazide after derivatisation and concentration. The main peak 2 at 16 min shows the expected 209 (M+H)+ ion of the 2-nitrobenzaldehyde derivative of semicarbazide together with its sodium adduct ion at m/z 231(Figure 19).
3.8 Cross-linking agents and cure accelerators (rubber) ISO standard 10398 provides methods for the identification of accelerators in cured and uncured compounds. Two methods are included. One is a GC method based on detection of trifluoroacetamide derivatives of the amines formed from acid hydrolysis. The second is a TLC procedure. Determination of the level of total sulfur in a rubber can give information on the type of cure system used, for example, elemental sulfur plus accelerator or sulfur donor system, etc. The ISO 6528-1:1992 method — Rubber — Determination of total sulfur content — Part 1: Oxygen combustion flask method is often employed. The principle of the method is oxidation by ignition in an atmosphere of oxygen in the presence of hydrogen peroxide, conversion of sulfur to sulfuric acid and determination of the sulfate by titration with barium perchlorate. The method is
586
John Sidwell
Intensity
2
1 0 5
10
15
20 Time/min
30
25
Figure 18 Positive electrospray extracted ion chromatogram of 1 ppm derivatised semicarbazide in water (scan 200–300 m/z).
Intensity
230.9
209.0 200
210
246.9 252.9
227.9 220
230
240
250
260
270
280
290
m/z
Figure 19 The mass spectrum of peak 2 in the chromatogram shown in Figure 18 showing ions of m/z 209 and 231.
applicable for the determination of all the sulfur present in a rubber or rubber product, except that contained in barium sulfate. Unreacted free sulfur can be determined to ISO 7269:1995 — Rubber — Determination of free sulfur. Three methods for the determination of free sulfur in vulcanized rubber are detailed: two versions of the copper spiral method and the sodium sulfite method. The copper spiral methods are also applicable, subject to limitations, to unvulcanised rubber. The technique of DSC can detect non-reacted rubber curatives such as residual peroxides. For identification of other organic rubber compounding ingredients such as waxes, and most antioxidants/antiozonants, sample extraction with diethyl ether, followed by GC-MS of the resulting extract is commonly employed. Examination of volatile species can also provide information on the nature of curatives employed. Rapra has undertaken extensive research on the nature of the breakdown products from rubber curatives. This has included studies for the U.K. Food
587
Additive Analysis
Abundance
Standards Agency [13,14]. The techniques of GC-MS, GC GC-ToFMS [15] and LC-MS have been used. Figure 20 shows the GC-MS chromatogram for the water extractables from a standard rubber compound NR2 of the formulation given in Table 8. The water extract was partitioned with dichloromethane in order to concentrate the organic extractables. The four main peaks in order of increasing retention time were identified as the CBS breakdown products cyclohexanamine, benzothiazole, cyclohexylformamide and mercaptobenzothiazole.
0 4
6
8
10
12
14
16 18 Time/min
20
22
24
26
28
Figure 20 GC chromatogram of the dichloromethane partition solution from the distilled water extract of the natural rubber compound NR2 (24 h at 401C). Table 8
Formulation for standard rubber compound NR2
Compounding ingredient
Parts per hundred of rubber (pph)
Natural rubber (SMR CV 60) Zinc oxide (cure activator) Stearic acid (cure activator) 4, 4u-Thio-bis-(3-methyl-6-tert-butyl phenol) (antioxidant) N-(1,3-dimethyl butyl)-Nu-phenyl-p-phenylenediamine (6PPD) (antiozonant) Hydrocarbon wax (Okerin 1944) HAF N330 Carbon Black (reinforcing filler) Naphthenic oil (petroleum-based oil lubricant Sulfur (curative) N-Cyclohexyl-2-benzothiazole sulfenamide (CBS) (cure accelerator)
100 5 1 1 1
Notes: Cure conditions: 6.25 min at 1551C.
2 35 5 1 2.5
588
John Sidwell
3.9 Fillers Analysis of inorganic fillers in plastics and rubber materials is normally accomplished by ashing material in a muffle furnace at a temperature of 5501C. An IR spectrum of the resulting ash, sometimes as a paraffin oil mull is then obtained to identify the filler type. Examination of the ash by XRF and/or X-ray diffraction can also provide useful information to help identify complex systems. Quantitative methods for determining inorganic filler or ash content of rubber are given in ISO 247:1990 Rubber — Determination of Ash. Two methods are described. Method A consists of heating a weighed test portion in a crucible over a gas burner, followed by volatilisation of the decomposition products and transfer of the crucible to a muffle furnace. The crucible is heated until all the carbonaceous matter has been burnt off and constant mass is attained. In method B, a weighed test portion is heated in a crucible in the presence of sulfuric acid, first by means of a gas burner and then in a muffle furnace as in method A. Platinum crucibles are used for ashing fluorine-containing and lithiumpolymerized rubbers. For plastics, ISO 3451 Plastics — Determination of Ash describes various methods for determination of the ash content of different types of plastics including those containing glass fibres and/or flame-retardants.
3.10 Flame-retardants Brominated and chlorinated organic flame-retardants can be analysed using either GC-MS or LC-MS. High resolution systems are required to identify the specific isomers. Quantification by bromine or chlorine content is normally achieved using XRF against standards in the same matrix.
3.11 Impact modifiers SEM and transmission electron microscopy (TEM) are employed to examine materials for the presence and distribution of impact modifiers such as polybutadiene rubber in high impact polystyrene (HIPS) and methacrylate butadiene styrene terpolymer in PVC. Quantification is either by transmission IR spectroscopy against standards or nuclear magnetic resonance (NMR) spectroscopy.
3.12 Lubricants and slip additives To examine slip additive concentrations in packaging films (typically 300–700 ppm), solvent extraction is used to remove the additive from the film. Hexane/ isopropanol (30/70 v/v) can be used to extract oleamide (fast bloom slip), stearamide and erucamide (slow bloom slip) from polyolefin films. GC or LC-MS is then employed to analyse the concentration of the extracted slip additive.
589
Intensity
Additive Analysis
0 2
4
6
8
min
Figure 21 LC-MS separation (in elution order) of myristic, palmitic, stearic and eicosanoic acids using positive ESI.
IR internal reflection spectroscopy can be used to distinguish the relative differences in the concentration of the slip additive at film surfaces. Figure 21 shows the LC-MS separation of fatty acid lubricants detected using positive ESI with specific ion monitoring as (MH). The following conditions were employed. Column: Luna C8(2), Phenomenex, 15 cm 2.00 mm, 5 mm Solvent A: acetonitrile Solvent B: 0.1% acetic acid in acetonitrile Gradient: 50% B to 20% B over 7 min Flow: 0.5 ml/min For lubricants such as polyethylene glycol, the molecular weight distribution can be studied using LC-MS with positive APCI (Figure 22).
3.13 Metal deactivators Metal deactivators such as Irganox MD1024 (N,Nu-bis(3-(3,5-di-tert-butyl-4hydroxyphenyl)propionyl) hydrazide) can be determined by LC-MS. Its chemical structure is given in Figure 23. Depending on the fragmentation voltage employed, the additive can be detected either as the molecular ion (MH) (Figure 24) or with additional fragmentation (Figure 25).
3.14 Nucleating agents Nucleating agents are used to improve the clarity of crystalline polymers such as polypropylene. Species such as diparamethyl-dibenzylidene sorbitol are
552.3
551.3
200
Figure 22
200
533.3 553.3 573.3
205.2 233.1 261.2 291.2
Intensity
20
100
80
60
400
400
899.5 901.5 900.5 943.5 944.5 945.5 987.5 988.5 989.5 1031.6 1032.6 1033.6 1075.6 1076.6 1077.6 1119.6 1120.6 1121.6 1165.7 1164.7 1163.7 1209.7 1208.7 1207.7 1252.7 1251.7 1297.8 1295.8 1339.8 1383.8 1427.8
40
768.4 767.4 812.4 811.4 855.4 857.4 856.5
591.3 635.3 679.3 723.3
590 John Sidwell
0 600 800 m/z
HO
600
1000
800
1200
APCI mass spectrum positive ion of polyethylene glycol.
O
NH
HN OH
O
Figure 23 Chemical structure of Irganox MD1024 (molecular mass 552).
m/z
1000
Figure 24 Irganox MD 1024 negative APCI mass spectrum at 190 V (MH). 1400
591
200
400
553.3 552.3
495.2
292.1 291.1 335.2334.2 361.1 391.1 417.2 449.2
257.1
205.1
Intensity
231.1
551.3
333.2
Additive Analysis
600
800
1000
m/z
Intensity
Figure 25 Irganox MD 1024 negative APCI mass spectrum at 400 V (greater fragmentation).
5
10
15
20
25
Time/min
Figure 26 Positive APCI chromatogram obtained for a 10 mg/ml standard of diparamethyldibenzylidene sorbitol.
employed, for example, Ciba Irgaclear DM. LC-MS methods can be employed for their detection and quantification. Figure 26 shows a positive ion APCI chromatogram for a 10 mg/ml standard of diparamethyl-dibenzylidene sorbitol together with its mass spectrum (Figure 27). Its presence in sample extracts can be identified from the (M+H)+ molecular ion at m/z 387 (Figure 28).
3.15 Pigments and dyes Pure pigments and dyes can be identified from their IR spectrum. Some reference spectra are given in the Hummel and Scholl collection [9]. Other than simple white pigments or solvent soluble types, identification of pigments in finished products is particularly difficult. Raman spectroscopy can aid the positive identification of pigments such as titanium dioxide.
592
John Sidwell
Intensity
387.2
369.2
300
Figure 27
350
400
450
550 m/z
500
600
650
700
750
Mass spectrum of the observed peak showing (M+H)+ ion at m/z ¼ 387.2.
Diparamethyldibenzylidene sorbitol
Intensity
Irgafos 168
Unidentified species
Irgafos 168 phosphate
Glycerol monostearate Irganox 1010
5
10
15
20
25
Time/min
Figure 28 Positive APCI chromatogram obtained for the toluene extract from a clear polypropylene material (after precipitation of polymer with methanol) spiked with diparamethyldibenzylidene sorbitol (antioxidants also detected).
3.16 Plasticisers The use of IR spectroscopy for the identification of plasticisers was discussed in Section 2.4. Separation by SEC is often required to confirm the use of polymeric plasticisers. Most of the common plasticisers for plastic materials can be detected and analysed either by GC-MS or LC-MS. Complex plasticisers such as epoxidised soya bean oil can be fully characterised by LC-MS using chromatography in hexane/propionitrile with detection by positive ion APCI. Fichtner and Giese [16] include plasticisers in their brief review of the application of LC-MS methodology to the identification of extractables from polymer materials.
593
Additive Analysis
3.17 Surfactants
266.1
Intensity
265.1
Schmitt [17] in his book on the analysis of surfactants includes details of a number of HPLC-based procedures. LC-MS can be used for positive identification. Figure 29 shows the molecular ion mass spectrum for the surfactant lauryl hydrogen sulfate detectable as its (MH) ion by positive ESI. Ionic surfactants such as sodium dodecyl sulfate can also be detected by ESI. Figure 30 shows an overlay of sub ppm concentrations detected using ion pair chromatography with specific ion LC-MS detection (positive ESI at m/z 265). Gradient elution from 50.0% water containing 5 mM acetic acid & triethylamine) to 50.0% 80/20 acetonitrile/water (5 mM acetic acid & triethylamine) was employed.
200
400 m/z
600
Figure 29 Mass spectrum for lauryl hydrogen sulfate (positive ESI).
530μg/kg Sodium dodecyl sulphate surfactant
Intensity
212μg/kg 106μg/kg 53μg/kg 26.5μg/kg 10.6μg/kg 0μg/kg 0 7.8
8
8.2
8.4
8.6
8.8
min
Figure 30 Overlay of standards sodium dodecyl sulfate (0–530 mg/kg) detecting m/z 265 with positive electrospray ionisation.
594
John Sidwell
3.18 UV stabilisers (light stabilisers) In studies for the U.K. Food Standards Agency, Sidwell and Zondervan [10] also examined the determination of benzophenone and benzotriazole UV stabilisers by LC-MS. Specific detection parameters using the elution conditions given in Section 3.4 are given in Table 9. HALS presents some analytical difficulties. Coulier et al. [18] describe a pyrolysis GC-MS method for identification and HPLC with UV and evaporative light scattering detection methods for quantification in polymer extracts. Three Ciba HALS stabilisers are currently approved for use in plastic foodcontact materials in Europe (Directive 2002/72/EC, Plastic materials and articles used in contact with food.) These are Chimassorb 944, Tinuvin 622 and Chimassorb 2020. Their chemical structures are given in Figures 31–33, respectively. These three polymeric HALS stabilisers can be detected and positively identified in extracts from polyolefins using an Agilent Ion-trap instrument with positive APCI. Figure 34 shows a chromatogram for a 5-ppm standard of Tinuvin 622 in tetrahydrofuran (THF) and the peak mass spectrum (Figure 35). Similar data for Chimassorb 944 in THF are shown in Figures 36 and 37, respectively. A Waters Xterra C8 150 2.00 mm 3 mm 125A column at 601C with the mobile phase of isopropanol +700 ml/l hexylamine was employed.
3.19 Monomers: Residual monomers A wide variety of methods have been developed for the detection of residual monomers in polymeric materials. Volatile monomers, for example, acrylonitrile, butadiene, vinyl chloride, etc., are normally determined using headspace GC methods. Suitable PLOT columns for the determination of vinyl chloride monomer in PVC include 15.00 m, 0.53 mm bonded polystyrene-divinyl benzene and 30 m, 0.53 mm porous divinyl benzene homopolymer types. Typical responses for vinyl chloride monomer standards (0.06, 0.19 and 0.31 mg/l) in N,N-dimethylacetamide expressed as mg/kg vinyl chloride (PVC sample) using the 30 m homopolymer column and flame ionisation detection are shown in Figure 38. An automatic static headspace sampler was employed. Other less volatile monomers such as those found in acrylic materials are detected and quantified in solution by GC. Derivatisation methods are employed for a wide variety of amine and hydroxyl monomers. CEN (Comite´ Europe´en de Normalisation) has published standard methods for the determination of extractable monomers from food-contact materials. These methods are detailed in Table 10.
3.20 Reaction products of polymerisation and cure Some of the reaction products of polymerisation and cure can be toxic, for example, aromatic amines from hydrolysis of isocyanates and bisphenol A from
Table 9 UV absorbers PM Ref.
CAS no
PM 48640 00131-56-6
SML Exact (mg/kg) mass
BRetent. Primary ion for time (mins) quantification +/ 0.1 m/z (ve APCI)
Confirmatory ions MS2 or other quantification ions +/ 0.1 m/z ve APCI
Uvinul 400
2,4-Dihydroxybenzophenone 4,4u-Dihydroxybenzophenone 2,2u-Dihydroxy-4methoxybenzophenone 2-(4,6-Diphenyl-1,3,5-triazin2-yl)-5-(hexyloxy)phenol 2-Ethoxy-2u-ethyloxanilide 2-(2-Hydroxy-3,5-bis(1,1dimethylbenzyl)phenyl)benzotriazole 2-(2u-Hydroxy-3utert-butyl-5u-methylphenyl)5-chlorobenzotriazole 2,4-Di-tert-butyl-6-(5chlorobenzotriazol-2-yl) phenol
6
214.06
1.4
213.0
168.9, 134.9
6
214.06
1.0
213.1
169.0, 93.1
6
244.07
1.6
243.0
199.0
0.05
425.21
8.0
424.2
340.0
30 1.5
312.15 447.23
3.7 13.3
311.1 446.2
108.0, 265.0 431.2
30
315.11
12.6
314.1
314.1(stable), 228.9
30
357.16
15.0
356.1
356.1 (stable), 305.1
PM 48720 00611-99-4 PM 48880 00131-53-3
Cyanasorb UV24
PM 51700 147315-50-2 Tinuvin 1577 PM 53200 23949-66-8 PM 60320 70321-86-7
Tinuvin 312 Tinuvin 234
PM 60400 03896-11-5
Tinuvin 326
PM 60480 03864-99-1
Tinuvin 327
595
Chemical name
Additive Analysis
Trade name
596
Table 9 (Continued ) PM Ref.
CAS no
PM 61360 00131-57-7
PM 61440 02440-22-4 PM 61600 01843-05-6
Chemical name
2-Hydroxy-4-nhexyloxybenzophenone 2-Hydroxy-42-Hydroxy-4methoxybenzomethoxybenzophenone phenone Tinuvin P 2-(2u-hydroxy-5u-methylphenyl)benzotriazole Chimassorb 81 2-Hydroxy-4-noctyloxybenzophenone
SML Exact (mg/kg) mass
BRetent. Primary ion for time (mins) quantification +/ 0.1 m/z (ve APCI)
6
298.16
6
228.08
Not examined 2.1 227.1
30
225.09
3.8
224.1
141.0, 181.0
6
326.19
10.5
325.2
212.9
Confirmatory ions MS2 or other quantification ions +/ 0.1 m/z ve APCI
210.9 low response
John Sidwell
PM 61280 03293-97-8
Trade name
Additive Analysis
Figure 31
597
Chimassorb 944.
Figure 32 Tinuvin 622.
Intensity
Figure 33 Chimassorb 2020.
1
2
3
4
5
6
Time/min
Figure 34 Positive APCI chromatogram obtained for 5 ppm standard of Tinuvin 622 in THF (scan 1,000–2,200 m/z).
598
John Sidwell
1165.7 1051.7
1448.9
Intensity
1335.7 1133.7
1000
1280.6
1200
1617.9 1562.8
1416.8
1400
1733.0
1600 m/z
1847.0
1800
2000
Intensity
Figure 35 The mass spectrum obtained for the peak in Figure 34 showing major ions of 1051.7, 1165.7, 1335.7.0 and 1448.9m/z (283 repeat unit of Tinuvin 622).
1
2
3
4
5
6
Time/min
Figure 36 Positive APCI chromatogram obtained for 5 ppm standard of Chimassorb 944 in THF (scan 1,000—2,200m/z).
Intensity
1593.5
1797.6 1051.6 1101.9 1198.0 1496.3 1134.7 1261.8 1334.8 1416.8
1200
1400
2191.9 2037.8 2093.8
1699.5
1600 m/z
1800
2000
Figure 37 The mass spectrum obtained for the first peak in Figure 36 showing major ions of 1198.0, 1593.5, 1797.6 and 2191.9m/z. (2191.9–1593.5 ¼ 598.4 is the repeat unit of Chimassorb 944.)
epoxy can coatings. Much attention has been given to the development of methods for detecting such species at parts per billion concentrations. Aromatic amines can be quantified by HPLC-MS either as their (M+H)+ ion or by further fragmentation into specific daughter ions (LC-MS-MS). Figure 39
599
Additive Analysis
3.1 mg/Kg VCM in sample
VCM CALIBRATION STANDARDS
Intensity
1.9 mg/Kg VCM in sample
0.6 mg/Kg VCM in sample
5
6
7
8
9
10
11
min
Figure 38 Detection of vinyl chloride monomer (VCM) by headspace GC.
shows a typical calibration curve obtained using an ion-trap instrument for the 2,2u methylene dianaline (MDA) isomer, quantified using the m/z 199 - 106 fragmentation (Figure 40). A linear calibration response was obtained for solutions in the concentration range up to 20 mg/l (ppb). Under the ion-trap collection conditions employed, non-linearity is apparent at higher concentrations. The extracted ion chromatogram (EIC) for the15 mg/ml solution is shown in Figure 41. The extractable bisphenol A content from epoxy can coatings can be examined in acetonitrile solvent extracts using specific ion monitoring for the (MH) ion. Figure 42 shows a typical chromatogram of extractable species having the m/z 227 ion of bisphenol A. For the can examined, the bisphenol A content of the acetonitrile extract solution (main peak at 6.7 min) was 82 mg/kg with the maximum extractable bisphenol A from the can being 62 mg/kg. This acetonitrile solvent extract concentration is 10 lower than the specific migration limit into food of 0.6 mg/kg.
3.21 Solvents Either static or dynamic headspace gas GC is used to examine residual solvents in polymeric materials. Figure 43 shows the complex volatiles liberated from a printed multi-layer salad wrap, heated at 3001C under nitrogen.
600
John Sidwell
Table 10 EN 13130 standard methods for the quantification of extractable monomers used for food-contact plastics EN 13130 standard
Title
Methodology
Part 1
Guide to test methods for the specific migration of substances from plastics Determination of terephthalic acid in food simulants
See parts 2–28
Part 2
Part 3
Determination of acrylonitrile in food and food simulants
Part 4
Determination of 1,3-butadiene in plastics
Part 5
Determination of vinylidene chloride in food simulants
Part 6
Determination of vinylidene chloride in plastics
Part 7
Determination of ethylene glycol and diethylene glycol in food simulants
Part 8
Determination of isocyanates in plastics
Part 9
Determination of acetic acid, vinyl ester in food simulants
Aqueous simulants — HPLC with UV detection. Olive oil extracted with dilute sodium hydrogen carbonate and the aqueous extract acidified and examined by HPLC Headspace GC with automated sample injection and specific nitrogen detector. Confirmation by GC-MS if required Headspace GC of the polymer dissolved in N,Ndimethylacetamide. Quantification by standard addition using pentane internal standard Headpace GC with electron-capture or flame-ionisation detection. Quantification by standard addition using 1-chloropropane internal standard Headspace GC of the polymer dissolved in N,Ndimethylacetamide with detection by electron-capture or flame-ionisation detection. Headpspace GC of the plastic if not soluble GC of aqueous simulant or water extract of olive oil using cold oncolumn injector. 1,4 butane diol internal standard Solvent extraction with dichloromethane and concurrent derivatisation with 9-(methylaminomethyl)anthracene. Fluorescent derivatives analysed by HPLC with fluorescence detection Headpace GC of simulants with flame ionisation detection. Methyl propionate internal standard
Additive Analysis
601
Table 10 (Continued ) EN 13130 standard
Title
Methodology
Part 10
Determination of acrylamide in food simulants
Part 11
Determination of 11-aminoundecanoic acid in food simulants
Part 12
Determination of 1,3-benzenedimethanamine in food simulants Determination of 2,2-bis(4hydroxyphenyl)propane (bisphenol A) in food simulants
HPLC of aqueous simulants or water using an ion exclusion column (styrene divinyl benzene polymer with sulfonated[cationic] ion-exchange groups). Derivitisation with fluorescamine, 4-phenylspiro-[furan 2-(3), 1-phthalan]-3,3-dione and HPLC with fluorescence detection Bis-derivitisation with fluorescamine and HPLC with fluorescence detection Aqueous simulants — HPLC with fluorescence detection. Olive oil extracted with methanol/water after addition of hexane Aqueous simulants — HPLC with UV detection. Olive oil extracted with 80% aqueous acetonitrile Headspace GC with FID detection and pentane internal standard Aqueous simulants GC. Olive oil extracted with water/ethanol and GC detection Dissolution of the polymer in dichloromethane and concurrent derivitisation with 2-aminophenol. The resulting 2-benzoxazolinone is determined by HPLC with UV detection Aqueous simulants examined by HPLC with UV detection. Olive oil extracted with distilled water, with determination in the water extract
Part 13
Part 14
Part 15 Part 16
Part 17
Part 18
Part 19
Determination of 3,3-bis(3-methyl4-hydroxyphenyl)-2-indoline in food simulants Determination of 1,3-butadiene in food simulants Determination of caprolactam and caprolactam salt in food simulants Determination of carbonyl chloride in plastics
Determination of 1,2-dihydroxybenzene, 1,3-dihydroxybenzene, 1,4-dihydroxybenzene, 4,4u-dihydroxybenzophenone and 4,4udihydroxybiphenyl in food simulants Determination of dimethylaminoethanol (DMAE) in food simulants
DMAE is extracted from simulants using solid phase extraction on a strong cation exchanger. The absorbed DMAE is removed from the absorbent with triethylamine and the resulting solution examined by GC using an internal standard
602
John Sidwell
Table 10 (Continued ) EN 13130 standard
Title
Part 20
Determination of epichlorohydrin in plastics
Part 21
Part 22
Part 23
Part 24
Part 25 Part 26
Part 27
Part 28
Methodology
Extraction of epichlorohydrin with dioxane, followed by microdistillation and derivitization with 9,10dimethoxyanthracene-2-sulfonic acid followed by reverse phase HPLC with fluorescence detection Derivitization of the free amine Determination of ethylenediamine using ethyl chloroformate and hexamethylenediamine in followed by GC with flame food simulants ionisation detection Determination of ethylene oxide Headspace gas chromatography and propylene oxide in plastics with diethyl ether as internal standard Determination of formaldehyde and In the case of HMTA, it is treated with acid and heated to release hexamethylenetetramine (HMTA) formaldehyde. Formaldehyde in in food simulants simulant is determined colorimetrically by reaction with chromotropic acid in the presence of sulfuric acid Determination of maleic acid and Ion pair HPLC of maleic acid with maleic anhydride in food cetyl trimethyl ammonium simulants chloride and UV detection (245 nm) with citraconic acid as internal standard Determination of 4-methyl-pentene Headspace GC with cyclohexane as in food simulants internal standard Determination of 1-octene and Headspace GC of the food simulant. tetrahydrofuran in food simulants Iso-octane internal standard for 1-octene and tetrahydropyran internal standard for tetrahydrofuran determinations Determination of 2,4,6-triaminoAqueous simulants — HPLC with 1,3,5-triazine in food simulants UV detection 230 nm. Olive oil extracted with water/isopropanol Aqueous food simulants are Determination of 1,1,1saturated with potassium trimethylolpropane (TMP) in food carbonate and extracted with simulants ethanol/ethyl acetate. After evaporation of solvent the extracted TMP is silyated with trimethylsilylimidazole in pyridine and determined by GC with flame ionisation detection
603
Additive Analysis
Figure 39
Calibration curve for 2,2u MDA at concentrations of 5, 10, 15, 20 and 50 mg/l.
Intensity
106.1
60
80
100
120
140
160
180
200
220
240
m/z
Figure 40 MS2 fragmentation of the m/z 199 ion for 2,2u MDA.
4. FUTURE DEVELOPMENTS IN ANALYTICAL METHODOLOGY Progress in all areas of additive analysis is very much associated with instrumental development. The last few years have seen major developments in the sensitivity of LC-MS and other MS-based techniques. Such developments are sure to continue. On the down side these analytical techniques provide a large amount of information obtainable per analytical run and therefore there is an increasing need for more automated accurate analytical equipment to improve data management. Many of the examples discussed in this chapter are ‘‘state of the art’’ in the author’s laboratory at the time of writing. However, as techniques and
604
Intensity
John Sidwell
0 2
4
6
8
10
12
14
16
18
Time/min
Intensity
Figure 41 Extracted ion chromatogram 15 mg/l 2,2u MDA.
0
2
4
6
8 10 Time/min
12
14
16
Figure 42 Examination of extractable Bisphenol A (Mass 228) from a can coating.
equipment develop, faster, more quantitative multi-analyte methods will undoubtedly emerge. For further information, Bart [19] in a paper published in 2003 has considered the future of polymer additive analysis starting from the basics and reviewing
605
Additive Analysis
Intensity
6.78
7.17 3.80 6.33 5.49 1.80
4.94
2.33
2
4
6
9.34 10.07 10.34 10.40 12.21
8
10
12
14
16
18
20
22
24
26
28
Time/min
Figure 43 Volatiles from a printed washed salad wrap (solvents from antimist coating and printing inks).
trends, polymer additive analysis at the instrumental extremes and advanced deformulation schemes.
REFERENCES 1 J. Bart, Additives in Polymers – Industrial Analysis and Applications, Wiley, Chichester, 2005. 2 D. Jenke, Chromatographic methods used to identify and quantify organic polymer additives, J. Liq. Chromatogr. Relat. Technol., 26(15) (2003) 2417–2447. 3 Regulation (EC) No 1935/2004 of the European Parliament and of the Council of 27 October 2004 on Materials and Articles intended to come into contact with food and repealing Directives 80/590/EEC and 89/109/EEC. 4 The European Pharmacopoeia, The European Directorate for the Quality of Medicines (EDQM) of the Council of Europe, 2006. 5 J.A. Sidwell, Examination of extractables from plastic and rubber components of medical products by GC-MS and LC-MS, Medical Polymers, Dublin, 2nd–3rd April 2003, Rapra Technology Ltd., Paper 8, 51–58. 6 J.A. Sidwell, Research on extractables from food-contact rubber compounds using GC-MS and LC-MS based techniques, RubberChem, Munich, June 2002. Rapra Technology Ltd. Paper 16, 117–121. 7 K. Grob, Comprehensive analysis of migrates from food-packaging materials; a challenge, Food Addit. Contam., 19(Supplement) (2002) 185–191. 8 J. Chalmers and G. Dent, Industrial analysis with vibrational spectroscopy, RSC Analytical Spectroscopy Monographs 1997, The Royal Society of Chemistry, Cambridge. 9 D. Hummel and F. Scholl, Atlas of Polymer and Plastics Analysis, Vol. 3, Additives and Processing Aids, Carl Hanser Verlag, Munich, Germany, 1981.
606
John Sidwell
10 J.A. Sidwell and E. Zondervan-vanden Beuken, UK Food Standards Agency project A3031/2, 2004, Development of multi-methods for determining the migration of antioxidants and stabilisers included in Directive 2002/72/EC-Final project report. 11 S.T. Hsiao, M.C. Tseng, Y.R. Chen and G.R. Her, Analysis of polymer additives by matrix-assisted laser desorption ionisation/time of flight mass spectrometer using delayed extraction and collision induced dissociation, J. Chinese Chem. Soc., 48 (2001) 1017–1027. 12 L. Fantoni and C. Simoneau, European survey of contamination of homogenised baby food by epoxidised soyabean oil migration from plasticised PVC gaskets, Food Addit. Contam., 20(11) (2003) 1087–1096. 13 J.A. Sidwell, UK Food Standards Agency Project A03019, 2001, Further research on chemical migration from food contact rubber and other elastomers — Final project report. 14 M.J. Forrest and B.G. Willoughby, Overview of Rubber Breakdown Products, 4th RubberChem Conference, 2004, Rapra Technology, Shawbury. 15 M. Forrest, S. Holding and D. Howells, The use of two-dimensional GC-MS for the identification and quantification of low molecular weight compounds from high performance elastomers, Polym. Testing, 25 (2006) 63–74. 16 S. Fichtner and U. Giese, Identification of extractables on polymer materials — application of LC-MS technology, Kautschuk Gummi Kunstoffe, 57(3) (2004) 116–121. 17 T.M. Schmitt, Analysis of Surfactants, 2nd ed., Marcel Dekker, Inc., New York, 2001. 18 L. Coulier, E.R. Kaal, M. Tienstra and T. Hankemeier, Identification and quantification of (polymeric) hindered-amine lightstabilizers in polymers using pyrolysis–gas chromatography– mass spectrometry and liquid chromatography–ultraviolet absorbance detection evaporative light scattering detection, J. Chromatogr. A, 1062 (2005) 227–238. 19 J. Bart, Polymer additive analysis at the limits, Polym. Degrad. Stab., 82 (2003) 197–205.
CHAPT ER
15 Failure, Defect, and Contaminant Analysis James D. Rancourt, Jennifer Brooks, Sue Mecham, Alan Sentman, Brian Starr and Jason Todd
Contents
1. Introduction 2. Case Studies 2.1 Section A: Aesthetics 2.2 Section B: Purity and contamination 2.3 Section C: Failure analysis 3. Summary References
607 608 608 618 647 673 674
1. INTRODUCTION Failure and contamination or a defect in polymer products and samples are often linked events. The presence of contamination, also referred to as impurities or foreign material, can lead to either a component failure or to a system failure. Poor visual quality, product failure, and property loss can also arise from process-induced defects and storage, such as polymer gels, additive bleed, degradation, discoloration, voids, blisters, crazing, stress cracking, etc. The extent and consequence of the failure can range from visual defects in the case of plastic film products through to mechanical fracture in the case of medical implant devices. Although each failure can be highly significant to the manufacturer and to the consumer, the consequence of failures can be highly varied, ranging from inconvenient to life-threatening. Contamination can be present not only as a surface deposit or a surface feature but can also be located within the bulk of a manufactured part. The selection of an appropriate series of analytical techniques, applied to failure, defect, and contamination analysis projects, is influenced by the location of the contamination or defect and the optical properties of the manufactured component. Microscopic analysis of opaque parts is limited to surface analysis Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00415-7
r 2008 Elsevier B.V. All rights reserved.
607
608
James D. Rancourt et al.
(see also Chapter 13). Bulk or sub-surface analysis usually requires destructive testing or sectioning to generate a fracture surface or exposed layer that now has the contaminant on the newly formed surface. Alternatively, X-ray analysis methods can be used to reveal the presence of internal contamination, and in some circumstances confocal Raman spectroscopy may be applicable. Raman microspectroscopy can also be particularly useful to characterizing carbon species, such as those produced in localized areas by degradation that cause visual defects, often named such as ‘‘black specks’’ [1]. The selection of an analytical technique that allows for the chemical characterization of a contamination or defect that is a potential contributor to a failure is influenced by some major factors. For example, some techniques are able to characterize inorganic materials, while other techniques are better suited for organic materials. Further, some analytical techniques require that the specimen be volatile, other techniques require that the sample be soluble, and still other techniques require that the sample be in a solid form. By utilizing a case study format, some specific examples of failure, defect, and contamination analysis are provided in this chapter. Each example is a real-life example from an industrial project. These case studies, in addition to providing specific detailed information about the techniques and approaches that were selected and the results that were obtained, also include information as to why other techniques were not considered appropriate. It is hoped that the reader will find these examples of interest. But, more importantly, the examples provided should assist a researcher, manufacturer, quality control department, or forensic engineer to develop an analytical approach that will provide objective sciencebased data to solve their unique failure, defect, and contaminant analysis problems. In particular, this chapter will demonstrate a systematic approach to characterizing contamination, defect, and failure cause, as undertaken in a multitechnique, third-party laboratory, with a time-limited investigation, owing to the urgency of most such analyses. In such a situation, pin-pointing the cause, rather than providing an absolute answer is more often the most business-critical solution, and efforts are sometimes restricted since information as to the fine detail of the problem context and material recipes is limited due to business confidentiality requirements. A comprehensive review of compositional and failure analysis of polymers, which includes many further examples of analysis of contaminants, inclusions, chemical attack, degradation, etc., was published in 2000 [2]. It includes details on methodologies, sampling, and sample preparation, and microscopy, infrared spectroscopy, and thermal analysis techniques.
2. CASE STUDIES 2.1 Section A: Aesthetics In today’s market, aesthetics is very important to both the consumer and the manufacturer. A consumer expects a product that has function, quality, and
Failure, Defect, and Contaminant Analysis
609
visual appeal. Contamination and surface blemishes are not desired in a product, especially such as those used in the interior of a newly purchased automobile. The four case studies featured in this section cover two automobile component complaints and two defect studies, one in a medical product and one in a consumer product.
2.1.1 Case study A1: Automotive components, interior trim In this case study, an automotive supplier was facing an issue of surface blemishes on sun visor arms. Portions of the sun visor arms used in automobiles can be manufactured from glass-filled thermoplastic polymers. Several visor arms contained visible blemishes on the surface. Typically, the steel insert of the visor arm is overmolded with the glass-filled thermoplastic polymer. Manufacturers sometimes utilize striations on the steel insert to provide a mechanical interlock with the over-molded thermoplastic polymer. However, in an improperly controlled environment, the mechanical process that produces the striations can also be the source of contamination and cause surface blemishes in the final product. To diagnose the surface blemish problem several analytical techniques were employed. First, the samples were photo-documented. Since an aesthetic problem is by definition a problem with the visual appearance of an item, it is important to ascertain if all the defects are different or of the same nature. With close inspection, the sun visor arms were found to contain two distinct types of defects. Figure 1(a) shows what was called the Type A defect and Figure 1(b) shows the so-called Type B defect. These images were acquired using a stereomicroscope coupled with a digital camera. From the samples collected from two lots of sun visor arms, the type and frequency of defects were tabulated to determine which type of defect was occurring most often. Table 1 indicates that the Type A defects were occurring
(a)
(b)
Figure 1 (a) Digital image of a Type A defect (112.5 magnification, the scale bar denotes 0.5 mm) and (b) digital image of a Type B defect (50 magnification, the scale bar denotes 1 mm).
610
James D. Rancourt et al.
Table 1 Visual examination data Lot
1 2
Defect type and frequency A
B
18 9
5 3
much more frequently than the Type B defects. The Type A defects accounted for 77% of the total number of defects. It was decided to initially characterize the Type A defect because this defect was occurring most frequently. Since the Type A defect appeared as a metal flake, scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (EDS) was selected as the next primary technique of choice. The scanning electron microscope provides magnification with a large depth of field, much larger than the stereomicroscope will allow. In addition, EDS allows for elemental analysis, which aids in determining, for example, if the sample is steel, stainless steel, or some other type of metal residue. Fourier transform infrared spectroscopy (FTIR), which is a commonly used technique in contamination and defect analysis, was not selected because the FTIR method of analysis is most useful for organic materials. One of the Type A defects was removed by micro-manipulation under the stereomicroscope and placed on an SEM sample stage. Double-sided conductive tape was used to ensure that the sample was sufficiently grounded to the sample mount. The sample was sputter coated prior to the SEM/EDS analysis. Sputtering was performed in order to deposit approximately 20 nm of gold/ palladium coating onto the sample. Sputter coating prevents the sample from charging by ensuring the surface of interest is conductive and thereby assures that the SEM depicts the surface topography. The mounted specimen was placed into the SEM vacuum chamber, and the chamber was sealed and depressurized. The SEM was operated at 5 keV for imaging and 20 keV for the EDS analysis. The approximate sampled area for the EDS analysis was 1 mm by 1 mm with a sampling depth of approximately 1 mm. Figure 2 shows the SEM image of the flake at a magnification of 350 , as it was mounted on the conductive carbon tape. If there is a polymeric film covering the sample, the SEM will only show the surface topography of the film, not the structure residing below the polymeric film. EDS was conducted on two areas on the sample as indicated in Figure 2. The EDS analysis was conducted in square spot mode, approximately 1 mm by 1 mm in size. The elemental results are shown in Table 2. Based on these data sets it is apparent that the Type A defect is an iron-rich particle. Based on the lack of chromium or nickel the Type A defect is a particle of steel, not stainless steel. Before the Type A defects had been documented by optical microscopy, an attempt had been made by the manufacturing facility to clean the striated steel inserts. Workers within the manufacturing facility were wiping the striated steel
Failure, Defect, and Contaminant Analysis
611
Area 1
Area 2
Contamination
Figure 2 The SEM micrograph of the Type A defect (350 magnification) with the arrows pointing to approximate sampling areas analyzed by EDS. Table 2
The elemental composition for the Type A defect as detected by EDS
Element
Aluminum Silicon Manganese Iron Total
Atomic percent Area 1
Area 2
Average
0.50 0.00 0.00 99.50 100.00
0.46 0.28 0.14 99.12 100.00
0.48 0.14 0.07 99.31 100.00
inserts with blue rags in an attempt to reduce the possibility of particulate contamination. This practice was, however, inducing a second type of defect. In this case, blue fibers, the Type B defect, were easily identified visually and their source in the process was known. However, for more difficult situations these fibers, or other contaminants, can be isolated and identified by FTIR or Raman spectroscopy. The spectroscopic identification aids in determining the probable sources of the contaminant. FTIR spectroscopy is a powerful analytical technique well known for its use in the identification, primarily, of organic materials; in recent years, Raman spectroscopy has been increasingly used in industry for complementary problem-solving and analysis, because of its potential for nondestructive sample analysis, and ready access to the low wavenumber region and consequent characterization of inorganic species. In this case, FTIR (or Raman)
612
James D. Rancourt et al.
(a)
(b)
Figure 3 (a) Digital image of the gasket material sample at 7.5 magnification and (b) digital image of the gasket material sample at 80 magnification.
spectroscopy could have been used to determine if the fibers were cotton, polyethylene, polyester, polyamide, or some other fiber-forming material. In conclusion, for this case study two types of defects were noted. The majority of the defects were metal flakes. The metal flakes were steel, not stainless steel, shown by the lack of chromium or nickel in the EDS analysis. It was concluded that during the molding process the glass-filled thermoplastic polymer was mechanically abrading the edges of the striated steel insert, resulting in metal shards being distributed throughout the sample.
2.1.2 Case study A2: Automotive components, gaskets In this case study example, automotive gasket material, comprised of a rubber coating on both sides of a sheet metal support, was analyzed. The sheet measured approximately 8v by 6v (ca. 20.3 cm 15.2 cm). The rubber coating was covered with very small defects that appeared as tiny blisters on the surface. Figure 3(a) shows the small blister defects present on the surface of an automotive gasket. Figure 3(b) shows a magnified image of the coating defect at 80 magnification. The defects were opened using a needle. This procedure exposed a white residue inside each defect. Figure 4 shows a representative view of a defect that has been opened thereby revealing the white residue. The diameter of six defects was measured inside the circled area shown in Figure 4. Table 3 shows the summary of the six defect diameters that were measured. The average diameter of the blister defects was approximately 230 mm. FTIR spectroscopy was conducted on the white residue using an attenuated total reflection (ATR) attachment [1].1 After the blister was opened, the ATR 1
The ATR technique is a commonly used infrared internal reflection sampling technique. It samples only the surface layer in contact with the ATR element; the sampling depth probed is typically of the order of 0.3–3 mm [1]. Unless software corrected, compared with a transmission spectrum, the relative intensity of bands within an ATR spectrum increase in intensity with decreasing wavenumber. Several FTIR instrument companies now supply ‘‘ATR-correction’’ software developed to correct for the different relative intensities of bands observed between ATR and transmission spectra, so that ATR spectra can be more easily compared to and searched against transmission spectra.
Failure, Defect, and Contaminant Analysis
613
Figure 4 Optical image of the residue within the tiny defects at 80 magnification (see Table 3).
Table 3 Defect (white residue particle) diameters measured from Figure 4 Defect number
Diameter (mm)
1 2 3 4 5 6 Average
235 284 243 226 210 178 229
attachment was brought into contact with the white residue. The ATR-corrected FTIR spectrum1, recorded from the white residue is shown in Figure 5. A match for this spectrum was searched for in a commercial database of library (reference) spectra. Figure 6 shows the top five spectral database matches from this search. The white residue spectrum has a 93% match score to that of calcium stearate, the second spectrum in the set of five closest matches. Of these five closest matches, it also visually matches best this spectrum; the differences in relative intensities of bands between the two spectra, for example, the CH stretching bands near 3,000 cm1 to the carboxyl salt stretching bands around 1,500 cm1, is probably a consequence of the different sampling techniques used to record the two spectra. A reference spectrum was acquired from the surface of the rubber coating to determine if there was any spectral interference with the analysis conducted on
614
James D. Rancourt et al.
0.09 0.08 0.07
Absorbance
0.00 0.05 0.04 0.03 0.02 0.01 0 4000
3500
3000
2500
2000
1500
1000
500
Wavenumber (cm-1)
Figure 5 ATR-corrected FTIR spectrum of the white residue that resides in the tiny defects shown in Figure 4.
Abs Abs
ATR: White Powder 0.05 0.00 1.0 CALCIUM SOAP OF STEARIC ACID PLUS SURFACTANT 0.5 Match:93.95
Abs
0.5 Match:93.29
Abs
1.0 OCTADECANOIC ACID, CALCIUM SALT 0.5 Match:85.51
Abs
1.0 CALCIUM STEARATE #1
1.0 CALCIUM STEARATE/ZINC STEARRATE MIX 0.5 Match:85.05
Abs
1.0 Sta-Brite #14 0.5 Match:84.27 3500
3000
2500 2000 Wavenumber (cm-1)
1500
1000
Figure 6 The top five spectral database matches to the ATR-FTIR spectrum acquired from the white powder inside the defects.
Failure, Defect, and Contaminant Analysis
615
ATR: surface of rubber gasket
Abs
0.14 0.10 0.06 0.02 2.0
Abs
POLYBUTADIENE (RANDOM CIS & TRANS) Match:65.99 1.0
0.0 3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 7 Top, ATR spectrum acquired from a reference area on the surface of the rubber gasket material and bottom, top spectral database search match.
the white residue. Spectral interference could occur because a portion of the ATR crystal may have been in slight contact with the rubber while mostly being in contact with the white residue. Figure 7 shows the spectrum acquired from the surface of the rubber coating along with its top spectral database match. As expected, the rubber coating did not show very strong absorbances. Most rubber materials compounded with carbon black do not show very strong FTIR absorbances. The FTIR spectrum of the rubber coating showed mostly polybutadiene along with the presence of a nitrile group indicated by the absorbance at 2,235 cm1. The spectrum shown in Figure 7 shows derivative-like bandshapes, a common occurrence with heavily filled carbon black samples, consistent with this spectrum exhibiting largely the characteristics of a front surface external reflection spectrum rather than a pure ATR spectrum [3]. The polybutadiene and nitrile functionalities are due to the nitrile butadiene base rubber (NBR). No surface contamination or interferences were evident that would interfere with the calcium stearate identification within the defect site. In conclusion, the white residue was identified by FTIR spectroscopy as calcium stearate. If additional information pertaining to the rubber composition were sought, FTIR analysis of the pyrolysis products would have been performed. Even more detailed analysis can be obtained by gas chromatography (GC) separation of the multiple pyrolysis products followed by mass spectrometric (MS) detection. The gas chromatography-mass spectrometry (GC-MS) method is well suited to deformulation and contaminant analysis.
616
James D. Rancourt et al.
2.1.3 Case study A3: Consumer product, molded disks Several injection-molded polycarbonate (PC) disks used in a consumer product (i.e., a clock face) were analyzed, because the disks contained defects. The defects were analyzed initially and imaged using a stereoscopic microscope fitted with a digital camera. The defects present on the samples were easily identified. It was noticed that the defects were located on different regions of the molded part. This important observation eliminated a systematic problem or an imperfection at a specific site on the mold surface as the cause of the defect. A representative defect was chosen to identify the site of the defect within the thickness of the molded part. A small section, approximately 7.5 cm by 5 cm, of one molded disk containing the defect was removed using a power drill and jigsaw. The defect was then imaged at 7.5 magnification (Figure 8(a)) and at 30 magnification (Figure 8(b)). Figure 8(b) shows a defect that occurred near the center of the molded disk. The defect appears to be quite symmetrical and aligns with the flow pattern resulting from the mold filling. The focal plane for both images is within the mold filling, indicating that the defect is not a surface feature. Instead, the defects appear to be voids that may be a result of a negative interaction occurring within material during processing. A cross-section of the defect was prepared, but the defect was not visible using optical light microscopy. SEM could have been used to image a cross-section. This would have enhanced visualization of the voids and would potentially identify other issues such as the presence of very small voids distributed through the part. The PC resin was a new grade of PC for the molder. Possible causes for these defects included excessive moisture in the resin or other problems with the viscosity. If the viscosity is either too high or too low, pumping the melt will become problematic and air may be introduced. Another potentially related issue is the fact that modest impact forces broke some of the molded disks. The molded PC disk is supposed to withstand physical abuse without breaking. In fact, PC is typically chosen for its inherent impact resistance. It is possible that the material was too low a molecular weight as received. It is also possible that the resin molecular weight was being degraded during the processing of the material.
(a)
(b)
Figure 8 (a) Defect area at 7.5 magnification and (b) defect area at 30 magnification.
Failure, Defect, and Contaminant Analysis
617
A drying step was conducted at 1181C in a large batch dryer for up to 8 h. This is a fairly lengthy period of time at a relatively high temperature. Often, in large pieces of heating equipment such as ovens and dryers, it is important to measure the temperature of the material at different positions within the dryer. Large temperature differentials are often identified that could be critical to the processing of the resin. If some of the material is getting substantially hotter for this long time period and the molecular weight is degrading, it could have a detrimental effect on the final molded parts. Likewise, if the temperature that the material attains in the mold stock, runners, and mold cavity is too high, the molecular weight can be degraded, affecting the viscosity of the material during molding and strength of the molded part. One would usually expect to see a yellow color accompanying polymer degradation and this is not evident in the part, but if there are additives to improve the color and clarity of the PC these could be masking a color change due to polymer degradation. Previously these disks were molded by a different manufacturer who did not have issues with the void defects observed by the current molder. The molecular weight of the polymer in the previously molded disks could be compared to the molecular weight of the polymer in the new clock faces. That comparison would typically be performed using gel permeation chromatography (GPC). The GPC data sets would aid clarification if molecular weight were an issue affecting the breaking strength of the parts, and consequently potentially affecting the processability of the resin. If it is identified by GPC that the new molded disks have significantly different molecular weights or molecular weight distributions compared with the old molded disks, then the resin should be analyzed from different points in the process to identify if the original resin is too low a molecular weight or if there is a critical step in the process that is degrading the polymer. In conclusion, in the limited study undertaken, the visual defects were indicated as being due to the presence of internal voids in the molded material.
2.1.4 Case study A4: Medical product, molded sheets A problem had arisen with molded parts from a medical products company. Some injection-molded sheets were exhibiting small translucent areas (gels) within the opaque polymeric material, which had been designated as non-melt areas. One theory for the source of the non-melt was that a contaminant was present, while another postulate was that these areas represented a cold slug coming from the sprue. One sheet was chosen for analysis since the area of non-melt within it was largest. Both the non-melt area as well as a ‘‘normal’’ area were tested. In order to first ascertain whether the non-melt area was a contaminant, ATR-FTIR spectroscopy was used to analyze and compare the two areas. It was found that both areas were polycaprolactone, and that the spectra match between the two was greater than 98%, indicating that they were the same base resin, thus ruling out a contaminant. These spectra are shown in Figure 9. The alternative theory for the presence of the non-melt areas was that there were processing differences between these two areas, such as would be the case if
618
James D. Rancourt et al.
Abs
0.6
Normal area
0.4 0.2
Abs
0.6
“Non melt” region
0.4 0.2 1.0
Abs
Polycaprolactone library spectrum 0.5
Sample Prep: cast film
3500
3000
2500
2000
1500
1000
Wavenumber(cm-1)
Figure 9 ATR infrared spectra for the ‘‘normal’’ (top) and non-melt (middle) areas of the injection-molded sheet and a library spectrum for a polycaprolactone (bottom).
a cold slug broke loose from the sprue. To test this hypothesis, differential scanning calorimetry (DSC) was applied to both areas. The resulting scans are shown in Figure 10, and the data are summarized in Table 4. The transition temperatures are slightly different between the two samples, and the same is true of the heat of fusion, which is related to the degree of crystallinity. The main variation between the two samples is in the shape of the melting endotherm, which is noticeably different. One would not have expected to see different levels of crystallinity, since at room temperature the samples are continuing to crystallize. However, the different shape in the melting endotherm is clear evidence of a different thermal history, which would support the theory of the cold slug.
2.2 Section B: Purity and contamination 2.2.1 Case study B1: Paints and coatings An aerosol paint used to mark boundaries on athletic fields had been causing damage to the grass. It was therefore deformulated in order to determine which of the ingredients might have led to this undesirable effect, which was essentially a system failure of the product. First, all the solvents present were identified by GC-MS (see later). It was expected that the solvent system was a combination of toluene, petroleum distillates, mineral spirits, and Varnish Maker’s and Painter’s (VM&P) naphtha. Second, the type and level of filler, expected to be typically titanium dioxide and calcium carbonate, and the resin (binder) were characterised by a combination of ATR-FTIR and inductively coupled plasma mass spectrometry (ICP-MS). (Raman spectroscopy would also have provided a good method for identifying the presence and type (rutile or anatase) of titanium dioxide [4].)
619
Failure, Defect, and Contaminant Analysis
-0.1
Heat Flow (W/g)
-0.6
––––––– ––––
"Normal" area Non-melt area
-1.1
-1.6
-2.1 -100
-50
0
50
100
Temperature (°C)
Figure 10 DSC scans for the ‘‘normal’’ (continuous line) and non-melt (dashed line) areas of the injection-molded sheet. Table 4
Summary of DSC results for the two samples
Sample
Tg (1C)
Tm (1C)
DHf (J/g)
‘‘Normal’’ area Non-melt area
64.81 62.92
57.81 59.26
68.04 71.31
Tg, glass transition temperature; Tm, melt temperature; DHf, heat of fusion.
The percent solids were measured by an evaporative drying technique. Approximately 15 g of paint was dispensed into a glass vessel with a very small vent. The contents were allowed to dry overnight uncovered in the fume-hood and then were dried in a vacuum oven at 801C overnight, until a constant mass value was attained. The percent solids were calculated to be 63.3 wt%. Similar to the percent solids test, the white-colored paint sample was dispensed into a vented glass vessel and poured into a Teflons (poly(tetrafluoroethylene)) boat. The paint sample in the Teflons boat was dried overnight uncovered in a fumehood and was then dried in a vacuum oven at 801C until a constant mass value was attained. A sample of this dried film was used for FTIR-spectroscopic analysis and ICP-MS spectroscopic analysis. In order to calculate the weight percent of binder in the dried paint sample an additional test, thermogravimetric analysis (TGA), would be needed. Figure 11 shows the ATR-FTIR spectrum acquired from the surface of the white-colored paint sample after the paint had been dried. Figure 12 shows the closest spectral library database matches obtained; Figure 13 compares the spectrum of the surface of the white-colored paint sample with that of a reference library spectrum of a vinyl toluene-modified alkyd. The binder from the dried
620
James D. Rancourt et al.
0.20
Dried paint off PTFE film
Absorbance
0.16
0.12
0.08
0.04
0.00 4000
3500
3000
2500
2000
1500
1000
500
Wavenumber (cm-1)
Figure 11 ATR-FTIR spectrum of the dried white-colored paint sample.
Abs
0.20 Dried paint off PTFE film 0.10
Abs
1.0 Alkyd, 65% soybean oil 0.5
Match:66.79
Abs
0.5
Abs
1.0 Alkyd, 68% castor oil + PAnh
1.0 Alkyd, tall oil fatty acids, 66% triclyc.+24% PAnh 0.5 Match:66.52
Match:66.69
3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 12 FTIR spectral library database matches to the spectrum shown in Figure 9 obtained from the dried white-colored paint sample.
white-colored paint sample has the highest spectral match score (67%) to an alkyd. The moderate–low match score to the reference vinyl toluene-modified alkyd and other alkyds is caused by additional absorption bands arising from fillers, in particular inorganic carbonate, which gives rise to an intense broad absorption band near 1,450 cm1. This paint sample contains fillers, and the reference vinyl toluene-modified alkyd does not. Figure 14 shows the best
Failure, Defect, and Contaminant Analysis
0.18
621
Dried paint off PTFE film
Abs
0.14 0.10 0.06 0.02 0.10
Abs
0.08
Match:62.20
0.06 0.04 0.02 0.00 3500
3000
2500 Wavenumber
2000
1500
1000
(cm-1)
Figure 13 FTIR library spectral match of the spectrum acquired from the dried white-colored paint sample (top) compared with a dried vinyl toluene alkyd reference sample (bottom).
0.18
Dried paint off PTFE film
Abs
0.14 0.10 0.06 0.02 1.0
Abs
0.8 0.6
Match:96.85 Chemical Name: Calcium Carbonate Type: Inorganic Pigment
0.4 0.2 3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 14 FTIR spectral library database search match, focused on the region around the peak at 1,450 cm1, to the spectrum obtained from the dried white-colored paint sample.
spectral database match when the region in the vicinity of the 1,500 cm1 peak is searched. Calcium carbonate shows a dominant peak in the FTIR spectrum near 1,450 cm1. To obtain a spectrum solely of the alkyd, a separation of the filler from the paint would be necessary. This approach would provide the best
622
James D. Rancourt et al.
spectroscopic result for the identification of the alkyd type and provide a better comparison to the reference vinyl toluene-modified alkyd. A 68 element ICP-MS scan was performed on one dried white-colored paint sample. The chemical elements scanned for during the ICP analysis and the detection limits are provided in Table 5. Approximately 0.5 g of each sample was prepared by an acid digestion technique prior to conducting the ICP-MS analysis. Shown in Table 6 are the quantified ICP-MS results for the sample. Elements scanned for but not detected are either not present in the sample or may be present below the detection limit.
Table 5
Elements shown in non-shaded squares were scanned for during ICP analysis
H Li
He Be
B
C
N
O
F
Ne
Na
Mg
Al
Si
P
S
Cl
Ar
K
§
Ca*
Sc
Ti
V
Cr
Mn
Fe
Co
Ni
Cu
Zn
Ga
Ge
As
Se
Rb
Sr
Y
Zr
Nb
Mo
Tc
Ru
Rh
Pd
Ag
Cd
In
Sn
Sb
Pt
Au
Hg
Ti
Pb
Bi
§
Cs
Ba
La
Hf
Ta
W
Re
Os
Ir
Fr
Ra
Ac
Unq
Unp
Unh
Uns
Uno
Une
Ce
Pr
Nd
Pm
Sm
Eu
Gd
Tb
Dy
Ho
Er
Tm
Yb
Lu
Th
Pa
U
Np
Pu
Am
Cm
Bk
Cf
Es
Fm
Md
No
Lr
§
§
Br
Kr
Te
I
Xe
Po
At
Rn
Note: Unless otherwise noted, the detection limit is 0.001 wt%; those marked y have a detection limit of 0.005 wt%; those marked have a detection limit of 0.03 wt%.
Table 6 ICP-MS results for the white-colored paint sample Element
Weight percent
Aluminum Boron Barium Calcium Iron Potassium Lithium Magnesium Manganese Sodium Nickel Phosphorus Silicon Strontium Titanium Zirconium
1.92 0.003 0.002 8.68 0.13 0.032 0.009 5.75 0.011 0.018 0.001 0.017 0.035 0.007 18.36 0.001
Total weight percent
34.98
Failure, Defect, and Contaminant Analysis
623
Table 7 Calculated filler levels of calcium carbonate and titanium dioxide based on the ICP results in Table 5 Filler type
Calcium carbonate Titanium dioxide Total weight percent
Weight percent In dried paint
In wet paint
21.7 30.6 52.3
12.6 17.7 30.3
Table 7 shows the calculated weight percent of calcium carbonate and titanium dioxide in the white-colored paint sample. These levels are based on the calcium and titanium levels shown in Table 6. Calcium carbonate was evident by the FTIR spectrum acquired from the dried paint sample, shown in Figure 13. (Had it been available, Raman spectroscopy, which gives ready access to the low wavenumber region, could have been used to confirm the presence (and polymorphic form) of titanium dioxide [4].) Given the white color of the paint, it is likely that the titanium present was present as titanium dioxide, and this was assumed in the calculations. The calculated weight percentage of calcium carbonate in the dried paint is 21.7 wt%, and 12.6 wt% in the paint containing the solvents. The titanium dioxide levels were calculated to be 30.6 and 17.7 wt% in the dried and solvent-containing paint sample, respectively. The spray paint can was inverted and a small amount of product was dispensed into a 20 mL glass headspace vial. The vial was immediately sealed and was incubated at 801C for approximately 30 min. After this isothermal hold, a 0.5-mL portion of the headspace was injected into the GC/MS system. The GC-MS total ion chromatogram of the paint solvent mixture headspace is shown in Figure 15. Numerous solvent peaks were detected and identified via mass spectral library searching. The retention times, approximate percentages, and tentative identifications are shown in Table 8 for the solvent peaks. These peak identifications are considered tentative, as they are based solely on the library search. The mass spectral library search is often unable to differentiate with a high degree of confidence between positional isomers of branched aliphatic hydrocarbons or cycloaliphatic hydrocarbons. Therefore, the peak identifications in Table 8 may not be correct in all cases as to the exact isomer present (e.g., 1,2,3-cyclohexane versus 1,2,4-cyclohexane). However, the class of compound (cyclic versus branched versus linear aliphatic) and the total number of carbon atoms in the molecule should be correct for the majority of peaks. As shown in Table 8, the spray paint solvent is predominately a mixture of several linear aliphatic, branched aliphatic, and cycloaliphatic hydrocarbons, and toluene, xylenes, and ethyl benzene. 2-Butanone (also known as methyl ethyl ketone) was also detected. The breakdown of the solvent mixture by class of compound (aromatic, n-alkane, iso-alkane, cyclic alkane, and others) is shown in Table 9. The solvent appears to be consistent with a mixture of a VM&P naphtha
624
James D. Rancourt et al.
RT: 4.00 - 14.00
6.82
100
Relative Abundance
90 80 70 60 50 40 30 20
6.30
10
4.15 5.06
0 4
5
5.93 6
7.49 8.68 6.91 7.91 8.91 9.01 7
8
9
10
10.52 10.97 12.21 12.36 13.76 11
12
13
14
Time (min)
Figure 15 GC/MS total ion chromatogram of the solvent headspace at 801C.
with toluene. Further quantification is possible to obtain a more accurate percentage with the submitted VM&P naphtha. The propellant mixture present in the can was also detected in the headspace GC/MS analysis. These peaks eluted very early in the chromatogram and were not well separated. The propellant was a mixture primarily of propane and the isomers of butane and pentane. In conclusion, the paint sample was comprised of 63.3 wt% solids (polymers and fillers) and 36.7 wt% solvent. The solids were likely comprised of calcium carbonate and titanium dioxide at 12.6 and 17.7 wt%, respectively, of the total sample including solvent. The calcium carbonate and titanium dioxide were calculated based on the measured levels of calcium and titanium from the ICP analysis. Not counting the calcium and titanium levels there is 4.9 wt% of additional metals present. Based on the calcium carbonate level and titanium dioxide level along with the remaining percentage of metals present, 34.9 wt% of the total sample is accounted for. Therefore, the maximum level of alkyd in the sample is 28.4 wt%. TGA is recommended in order to quantify the level of alkyd and total level of mineral fillers in the dried paint sample. The FTIR spectrum for the dried paint resin does have a reasonable match score to and feature bands characteristic of an alkyd resin [5]. Due to the presence of fillers though, the spectral analysis did not allow for a high-quality match to be obtained. Removal of the fillers and subsequent FTIR analysis would provide the best spectroscopic result for the identification of the alkyd type and provide a better comparison to such as the reference vinyl toluene-modified alkyd. The solvents encompass 36.7 wt% of the paint sample. The solvent appears to be consistent with a mixture of a VM&P naphtha with toluene. Toluene is the major constituent.
625
Failure, Defect, and Contaminant Analysis
Table 8
Solvent peak identification and percentages
Retention time (min)
Identification
Approximate amount (%)
Match score (%)
4.150 4.427 5.055 5.435 5.615 5.922 6.103 6.298 6.533 6.580 6.650 6.757 6.812 6.905 7.025 7.095 7.177 7.304 7.430 7.453 7.484 7.621 7.798 7.908 7.968 8.009 8.159 8.257 8.273 8.411 8.484 8.492 8.533 8.598 8.648 8.678 8.711 8.786 8.851 8.909 9.003
2-Butanone Heptane Cyclohexane, methylCyclopentane, 1,2,4-trimethylCyclopentane, 1,2,3-trimethylHeptane, 2-methylHeptane, 3-methyl1,3-Dimethylcyclohexane Cyclohexane, 1,1-dimethylCyclopentane, 1-ethyl-2-methylOctane Cyclohexane, 1,2-dimethylToluene Cyclohexane, 1,3-dimethylCyclopentane, butylHeptane, 2,2-dimethylHexane, 2,3,4-trimethylHeptane, 2,6-dimethylCyclohexane, 1,2-dimethylCyclohexane, 1,3,5-trimethylCyclohexane, ethylCyclohexane, 1,1,3-trimethylCyclohexane, 1,2,3-trimethylCyclohexane, 1,2,4-trimethyl2-Butanone, oxime Octane, 4-methylOctane, 3-methylPentalene, octahydroAcetic acid, butyl ester Cyclohexane, 1,2,4-trimethylCyclohexane, 1,2,4-trimethylCyclohexane, 1,2,4-trimethylCyclopentane, 1-methyl-2-propylcis-1-Ethyl-3-methyl-cyclohexane 1-Ethyl-3-methylcyclohexane Nonane Ethylbenzene Cyclohexene, 1-propylCyclooctane, 1,2-dimethylm-Xylene, p-xylene 1-Ethyl-3-methyl-cyclohexane
0.76 0.04 0.17 0.06 0.09 0.96 0.79 5.53 0.06 0.03 3.68 2.01 44.08 1.98 0.17 0.07 0.34 1.22 1.13 1.12 4.64 2.52 0.57 2.42 0.33 2.26 1.54 0.22 0.40 0.87 0.16 0.37 0.15 1.18 0.75 3.28 0.51 0.04 0.08 1.39 1.51
95 89 95 91 92 92 95 95 84 89 95 92 94 96 82 92 89 94 84 68 93 90 87 87 90 88 91 88 92 93 87 87 91 92 85 96 94 76 78 96 91
626
James D. Rancourt et al.
Table 8 (Continued ) Retention time (min)
Identification
Approximate amount (%)
Match score (%)
9.212 9.269 9.386 9.406 9.411 9.453 9.554 9.605 9.610 9.696 9.866 9.912 10.045 10.254
Octane, 2,5-dimethylCyclohexanepropanolOctane, 2,6-dimethylCyclohexane, propylCyclohexane, (1-methylethyl)o-Xylene Heptane, 3-ethyl-2-methylCyclohexane, 1,2-diethylCyclohexane, 1-ethyl-2,3-dimethylC10 cycloalkane Nonane, 4-methylC12 alcohol or alkene C12 cycloalkane Cyclohexane, 1-methyl-4-(1methylethyl)Cyclohexane, 1-isopropyl-3-methylCyclohexane, 1-methyl-2-propylDecane C10 cycloalkane Cyclohexane, 1-methyl-2-propylC10 cycloalkane Octane, 2,3,7-trimethyl1-Decanol, 2-hexylCyclohexane, butyl1-Octanol, 2-butylOctane, 3-ethylDecane, 2-methylDecane, 3-methylNaphthalene, decahydroUndecane Dodecane
0.16 0.73 0.55 1.44 0.95 0.29 0.25 0.18 0.13 0.10 0.34 0.49 0.56 0.08
88 87 91 84 89 92 84 80 84 83 91 82 80 86
0.07 0.44 1.29 0.06 0.23 0.05 0.68 0.11 0.57 0.10 0.04 0.10 0.04 0.15 0.33 0.02
74 88 95 80 80 70 86 79 74 77 80 87 92 93 96 84
10.320 10.394 10.521 10.622 10.674 10.819 10.970 11.190 11.254 11.532 11.588 11.645 11.765 11.831 12.207 13.760
2.2.2 Case study B2: Molded parts A part, consisting of a carbon fiber composite tube, was initially adhered to the inside of a short titanium coupling by a silica-filled epoxy. The bond failed and a fluorinated mold release was believed to be the cause of the failure and was the purpose for this investigation. A sample of the epoxy (Sample A) and the part (Sample B) were submitted for X-ray photoelectron spectroscopy (XPS) to analyze for the presence of both fluorine and silicon.
Failure, Defect, and Contaminant Analysis
627
Table 9 Solvent breakdown by category Category
Approximate amount (%)
Aromatics Cyclic alkanes Branched alkanes n-Alkanes Ketones Others
46.27 32.84 9.30 8.64 0.76 2.19
Total
100.00
A section of the epoxy sample, approximately 2 cm 2 cm, was removed from the bulk and mounted onto the XPS sample stage. The sample was mounted with the ‘‘titanium’’ side facing down, by way of double-sided tape. Thus, the ‘‘composite side’’ was analyzed. The composite tube was prepared similarly and the sampling area was selected so as not to include the first 5 mm or beyond 30 mm from the end of the tube. The regions in the first 5 mm and the area beyond 30 mm from the end were classified as the non-bonded regions. Thus, the ‘‘epoxy side’’ or outer surface side of the composite tube was analyzed in the ‘‘bonded region’’. The mounted samples were placed in the XPS vacuum chamber, and the chamber was evacuated prior to testing. The samples were exposed to the X-rays at 14.0 kV and 300 W. The approximate sampling area for the XPS is ˚ at a 451 exit 1.0 mm 3.5 mm with a sampling depth of approximately 35.0 A angle. Figures 16 and 17 show the survey scans from the epoxy and composite sample, respectively. Both show the presence of fluorine, which indicates the probable presence of a mold-release agent. Figures 18 and 19 show the results from the multiplex analysis, which shows the approximate atomic concentrations present on the surface. XPS is a surfacesensitive technique, which analyzes nominally the outermost 6 nm of the surface. The Si 2p binding energy regions are shown in Figure 20 for the two specimens. Both show a Si 2p binding energy of 101.8 eV. A binding energy of 101.8 eV is consistent with the binding energy of silicon in the form of a silicone (i.e., most likely a polydimethylsiloxane (PDMS)). The binding energy of silicon in silicates is closer to 102.5 eV, whereas silicon in the form of silicon dioxide is near 103.5 eV. In conclusion, there is a strong fluorine response in the XPS data set, which indicates the presence of a mold release. The binding energy of the silicon best matches that for a silicone, not silicon dioxide. Analysis of the actual filler (silica) used in the epoxy could eliminate it as a possibility since silane-based surface treatments are common.
2.2.3 Case study B3: Packaging A dispensing bag from a customer’s competitor was submitted for a partial deformulation of the film laminate layer structure since this bag was performing in a superior manner to the customer’s own product. The goal of the work was to
628
James D. Rancourt et al.
Min: 342 Max: 73533 C 1s Na 1s
C KLL
N(E) O 1s O KVV F 1s
F KLL
Ca 2p N 1s Na KLL
1100
990
880
770
660
550
440
330
220
Si 2p Si 2s 110
0
Binding Energy (eV)
Figure 16 XPS survey scan of Sample A. Min: 264 Max: 71073
Na 1s C 1s C KLL
N(E) O 1s O KVV F 1s
F KLL Ca 2p N 1s Na KLL Si 2sSi 2p
1100
990
880
770
660
550
440
330
220
110
0
Binding Energy (eV)
Figure 17 XPS survey scan of Sample B.
understand why this product was superior to that produced by the customer. Prior to any analysis, it was communicated that this film was a multi-layer co-extruded film made primarily of a linear low-density polyethylene (LLDPE) and a polyamide. The deformulation included obtaining SEM images to indicate
Failure, Defect, and Contaminant Analysis
629
Min: 0 Max: 100
59.4 % %
9.6 %
17.6 % 1.0 %
C 1s
Ca 2p
F 1s
N 1s
8.9 %
0.5 % Na 1s
O 1s
3.0 % Si 2p
Region
Figure 18 The elemental summary from the XPS multiplex analysis on Sample A shown in atomic percent.
Min: 0 Max: 100 94.7 %
%
0.7 % C 1s
Ca 2p
0.6 % F 1s
1.2 % N 1s
0.3 % Na 1s
0.8 % O 1s
1.7 % Si 2p
Region
Figure 19 The elemental summary from the XPS multiplex analysis on Sample B shown in atomic percent.
the number of layers present and ATR-FTIR spectroscopy analysis for identification of both the outside and inside layers. FTIR spectroscopy was also undertaken in transmission mode to gain a composite spectrum of all the layers. Nuclear magnetic resonance (NMR) spectroscopy was also conducted in two solvents to identify the polymeric materials present in the construction of the film
630
James D. Rancourt et al.
Figure 20 XPS Si 2p multiplex region of (a) Sample A and (b) Sample B.
laminate more specifically and to look for signs of the presence of additional materials. A section of the film was removed from the bag and was immersed in liquid nitrogen. The section was then freeze-fractured and mounted on the SEM stage with the outside surface of the bag section facing downward. The sample was sputter coated prior to SEM/EDS analysis. Sputtering was performed to deposit approximately 20 nm of gold/palladium onto the sample. Double-sided conductive tape was used to ensure that the sample was sufficiently grounded to
Failure, Defect, and Contaminant Analysis
631
Inside Inside
Possible tie layer Possible tie layer
Outside Outside
(a)
(b)
Figure 21 (a) SEM cross-sectional image of the film sample after freeze fracturing. The outside surface is down. (b) Enlarged view. The outside surface of the bag section is facing downward.
the sample mount. The mounted specimen was placed into the SEM vacuum chamber, and the chamber was sealed and depressurized. The microscope was operated at 5 keV for imaging. Figures 21(a) and 21(b) show the SEM micrographs of the freezefractured cross-section of the film used in the construction of the bag. There are two distinct layers and possibly a third very much thinner tie layer. The outside layer is a layer of nominal thickness 13 mm. The inside layer is much thicker and is approximately 70 mm thick. At the interface between the outer and inner layers the apparent very thin tie layer is about 1 mm thick. This is too thin to be identified by FTIR microscopy on a cross-section of the sample, since the technique is diffraction-limited, which means that layers of about 10 mm thickness or greater can only be readily identified [1]. The tie layer thickness is also probably too thin for fingerprinting by Raman microspectroscopy on a cross-section; the lateral spatial resolution of Raman microspectroscopy is about 1–2 mm. ATR-FTIR spectroscopy was conducted on the inner and outer surface of the dispensing bag film. The spectra acquired from the inner and outer surfaces are shown in Figures 22 and 23, respectively. The mid-infrared ATR spectrum of the inner surface, shown in Figure 22, displays all the features expected of a polyethylene; these are the saturated aliphatic CH stretching (nCH) between 3,000 and 2,800 cm1, the CH deformation bands in the region 1,500–1,300 cm1, and the 720/730 cm1 doublet CH rocking mode absorption bands indicative of a crystalline long chain aliphatic hydrocarbon [6]. Indeed this spectrum had a 96% match score to a polyethylene spectrum contained within the library searched. To fully characterize this layer as a LLDPE would require recording a more intense spectrum, for example by transmission of the separated layer, so that one could better observe in more detail the weaker absorption bands [1], and also examine the layer by either DSC or NMR, or both, in order to confirm that the polymer was indeed a LLDPE. In Figure 22, the weak absorption bands between 1,700–1,500 cm1 and 1,300–900 cm1 suggest the presence of another
632
James D. Rancourt et al.
0.16
Inside surface
0.14
Absorbance
0.12 0.10 0.08 0.06 0.04 0.02 0.00 4000
Figure 22
3500
3000
2500 2000 Wavenumber(cm-1)
1500
1000
500
The ATR-FTIR spectrum acquired from the inside film surface of the dispensing bag.
0.1
Abs
0.0 NYLON [NYLON 6,6] 0.6 Match:93.50 0.4 0.2 0.8 NYLON [NYLON 4] 0.6 Match:93.44 0.4 0.2
Abs
Abs
Abs
0.2 Outside surface
0.8 NYLON [NYLON 4] 0.6 Match:93.44 0.4 0.2 3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 23 Top spectrum, ATR-FTIR spectrum from the outside film surface of the dispensing bag. Also displayed are the three best matches from a library search of the top spectrum.
low-concentration component being present. The ATR-FTIR spectrum of the outer surface, shown in Figure 23, has a 94% match score to a library spectrum of nylon 6,6, which is also shown in Figure 23. While this spectrum is undoubtedly that of a nylon, confirming that it is unequivocally type nylon 6,6 would require complementary information, such as that from a DSC study.
633
Failure, Defect, and Contaminant Analysis
2.2 2.0 1.8
Absorbance
1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 4000
3500
3000
2500
2000
1500
1000
500
Wavenumber (cm-1)
Figure 24 Absorbance infrared spectrum acquired from the entire film sample by transmission spectroscopy.
Transmission FTIR spectroscopy was also conducted on the film sample; this is shown as an absorbance spectrum in Figure 24. Although, the spectrum is dominated by absorption bands arising from the nylon and polyethylene components, some additional features are evident, in particular an absorption band near 1,750 cm1, suggesting perhaps the presence of a polyester. The top spectral library matches were to those of nylon. In an attempt to obtain some complementary information, a section of the film was dissolved in 1 part trichlorobenzene (TCB) and 2 parts ortho-dichlorobenzene (o-DCB), a known good solvent system for polyethylene type polymers. Figure 25 shows the 1 H NMR spectrum recorded from this dissolved material. It reveals only polyethylene protons at 1.5 ppm; the signals from 7.1 to 7.5 are due to solvent peaks. The methine proton of the polyester poly(vinyl acetate), a common hot melt adhesive layer, would show a peak at 4.8 ppm if it were present. Ethylene vinyl acetate was not detected in the sample. Even with scale expansion, the peak at 4.8 ppm was not evident. Figure 26 shows the 13C NMR spectrum obtained in the same solvent. The 13C NMR spectrum also indicates the presence of polyethylene by the peaks at 24.4 to 24.9 ppm. The 13C NMR spectrum can also provide evidence for the level of branching provided the adjacent signals from 5 to 34 ppm are solely due to branches and not additives. The branch content based on the integration of the 24.4 peak to the adjacent peaks from 5 to 34 ppm indicates that there are 14 branches per 1,000 carbons, consistent with a higher methyl content for a LLDPE than the typically lower measured level for a high-density polyethylene (HDPE). A section of the film was dissolved in 3 parts deuterated chloroform (CDCl3) plus 2 parts 1,1,1-trifluoroethanol (TFE), a known good solvent system for
634
James D. Rancourt et al.
Figure 25 1H NMR spectrum of the film sample dissolved in 1 part trichlorobenzene and 2 parts ortho-dichlorobenzene.
polyamide polymers. The 1H NMR spectrum of the soluble portion of the film is shown in Figure 27. The signal at 7.26 ppm and the large signals near 3.9 and 4.8 ppm are due to solvent resonances. The signal at 8.30 ppm is due to 1,4-dinitrobenzene (DNB) internal standard. The signals at 1.26 ppm, 1.46 ppm, 1.55 ppm, 2.13 ppm, and 3.13 ppm are characteristic of methylene groups in polyamide 6 or polyamide 6,6. The signal at 6.44 ppm represents amide protons on the polyamide material. It is not possible from this spectrum alone to determine if the polyamide portion of the film sample is polyamide 6 or polyamide 6,6. However, one of these two polymers is present, and no signals other than those attributed to polyamide were detected in the 1H NMR spectrum of this sample. The 13C NMR spectrum of the portion of the film sample soluble in 3 parts TFE and 2 parts CDCl3 is shown in Figure 28. The signals at 77.23 ppm, 60 ppm, and the large quartet between 120 and 130 ppm are due to solvent resonances. The signals at 123 and 151 ppm are due to a DNB internal standard. The signals at 25.4 ppm, 26.3 ppm, 28.8 ppm, 36.4 ppm, and 39.7 ppm are characteristic of methylene groups on polyamide 6. From the 13C data, it is possible to distinguish between polyamide 6 and polyamide 6,6 polymers. The signal at 175 ppm is due to the carbonyl carbon in polyamide 6. As with the 1H NMR spectrum, no signals indicating the presence of other materials in the sample were observed.
Failure, Defect, and Contaminant Analysis
635
Figure 26 13C NMR spectrum of the film sample in 1 part trichlorobenzene and 2 parts ortho-dichlorobenzene.
The amount of each polymer in solution can be calculated by comparing the polymer integrals to the integral of signals due to the DNB internal standard. Table 10 shows the results for calculations of polyethylene in the o-DCB/TCB NMR samples, and for polyamide 6 in the CDCl3/TFE NMR samples. For the polyethylene calculations, there is a large discrepancy between the values derived from the 1H and 13C NMR spectra. This is probably due to incomplete dissolution of the polyethylene layer in the 13C NMR sample. The much larger surface area needed to achieve the desired sample mass for the 13C sample resulted in parts of the film being above the level of the solvent during heating and dissolution. This was less of an issue for the polyamide content of the samples, since polyamide is soluble in the NMR solvent at ambient temperature. The values for polyethylene from the 1H NMR and for polyamide from 1H and 13 C NMR are in the ranges consistent with the layer thicknesses observed in the SEM images. No signals that would correspond to the tie layer observed by SEM were noted in any of the NMR spectra. From the analyses carried out, the conclusion is that the dispensing bag is comprised of three layers; an inner polyethylene-based layer, an outer polyamide layer, and what appears to be a third, very thin, tie layer. The polyethylene in the inner layer has approximately 14 branches per 1,000 carbons and is
636
James D. Rancourt et al.
Figure 27 1H NMR spectrum of the film sample in 2 parts trifluoroethanol and 3 parts chloroform-d.
approximately 70 mm (2.75 mil) thick. The polyamide layer is approximately 13 mm (0.5 mil) thick. The tie coat is less than 1 mm thick; it may well be polyester based. These data were then used by the customer to compare their dispensing bag to the competitor bag in order to determine the critical components that were providing improved performance for the competitor product.
2.2.4 Case study B4: Automotive components, fuel injectors In this relatively simple example, a contaminant material had been noticed on the surface of a fuel delivery system component made by an automotive manufacturer. The identity of the contaminant, descriptively named ‘‘black goo’’, was required so that the source could be determined and the problem eliminated in the future. The contaminant material was removed from the injector with a clean needle and was transferred to a glass microscope slide. The contaminant was then analyzed using ATR-FTIR spectroscopy. The resulting spectrum is shown in Figure 29, indicating the sample to be a branched aliphatic hydrocarbon. The best library matches are shown in Figure 30. The best match is an oil, implying there may be lubricating agents in the component part. The presence of the small peak at about 1,750 cm1 (nC ¼ O) in Figure 29 indicates that the sample may be oxidized, consistent with heating of the material.
Failure, Defect, and Contaminant Analysis
637
Figure 28 13C NMR spectrum of the film sample in 3 parts trifluoroethanol and 2 parts chloroform-d. Table 10
NMR results
Solvent
Experiment
Mass of polyethylene from NMR (g)
Sample mass (g)
Polyethylene (wt%)
2:1 o-DCB/TCB
Proton Carbon
0.0325 0.1182
0.0552 0.5300
58.8 22.3
Solvent
Experiment
Mass of polyamide from NMR (g)
Sample mass (g)
Polyamide (wt%)
3:2 CDCl3/TFE
Proton Carbon
0.0056 0.0875
0.0538 0.5130
10.4 16.8
2.2.5 Case study B5: Automotive components, fuel delivery system module An automotive component supplier manufacturing a fuel delivery system module noticed contamination, appearing as whitish-yellow particles, in one unit. Some initial testing included both FTIR spectroscopy and SEM. However, additional testing was requested in order to independently and more accurately determine the source of the contamination. Preliminary testing indicated that the
638
James D. Rancourt et al.
0.20 0.18
“Black goo”
0.16
Absorbance
0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 3500
3000
2500 Wavenumber
2000
1500
1000
1500
1000
(cm-1)
Figure 29 Infrared spectrum of the injector contaminant.
Abs
0.2 0.1
Abs
1.0
Abs
PARAFFINIC BASE OIL Match:98.29
0.5 1.0
Mineral oil + lanolin alcohol Match:97.86
0.5 1.0
Abs
“Black goo”
Poly(1-octene) Match:97.41
0.5
3500
3000
2500
2000
Wavenumber(cm-1)
Figure 30 Infrared spectrum of the injector contaminant (‘‘black goo’’) along with the three best library matches.
contaminant was a polyamide. Since the only polyamide in the fuel delivery system module was in a filter, attention was focused on this specific part. In addition, an end cap and a metal tube were also shown to exhibit contamination, so these parts were also examined.
639
Failure, Defect, and Contaminant Analysis
O
B
A
E
C
D
H N
*
B
A
N H
*
D
E
C
O
Figure 31
1
H NMR spectrum recorded from the fuel deliver system module filter material.
In order to more accurately identify the contaminant, and to determine if the fuel delivery system module filter was the source, both materials were analyzed using 1H NMR spectroscopy. Samples were dissolved in a 60:40 mixture of deuterated chloroform/triflouroethanol. It should be noted that the amount of contaminant available for analysis was quite small, so for this sample, the NMR spectral acquisition time was set to 1 h in order to record a spectrum of adequate signal-to-noise ratio. Figure 31 shows the NMR spectrum recorded from the polyamide filter, and it is a high-quality match with polyamide 6,6, the structure of which is shown on the figure. Figure 32 compares the NMR spectrum for the filter along with that of the contaminant. Although the contaminant spectrum has more noise due to the low level of material available, it is evident that the spectrum acquired from the contaminant has peaks identical to those of the filter. Therefore, it can be concluded that the contaminant is polyamide 6,6, and the likely source was the fuel delivery system module filter.
2.2.6 Case study B6: Packaging Samples of three different polypropylene (PP) cups were submitted for analysis of contaminants found on their surfaces. Several cups that showed a yellow contaminant and both large and small cups with a green contaminant were
640
James D. Rancourt et al.
Figure 32 Stacked 1H NMR spectra of the contaminant (top) and fuel delivery system module filter (bottom) samples.
analyzed by ATR-FTIR spectroscopy using a Ge ATR element, which was brought into contact with the sample being analyzed. The resulting spectra were then compared to a spectral library in order to determine the principal chemical nature of the contaminants. The yellow contamination was removed from the cups using a clean needle and the contaminant was transferred to a glass slide. The contaminant was partially liquid with solid portions also present. When the ATR crystal was allowed to very slightly contact the sample, the liquid portion of the contaminant was detected and the spectrum recorded is shown in Figure 33. When higher contact pressure between the ATR crystal and the contaminant was used, a completely different spectrum was produced (see Figure 34) from the solid portion of the contamination. The spectrum in Figure 33 shows a very high-quality match to common vegetable oil. The spectrum of Figure 34, which is mostly representative of the solid phase, however, is more difficult to interpret. From the library used, the best matches to the total mid-infrared spectrum are to pullulan, a polysaccharide, although the match percentage is fairly low (partly because of interference from absorption bands due to the liquid phase vegetable oil). There are quite obvious similarities to the pullulan spectrum, especially in the region from 1,400 to 900 cm1 and the nOH stretching region (ca. 3,600–3,100 cm1). In order to try to
Failure, Defect, and Contaminant Analysis
641
Abs
Yellow contamination
0.1 0.0
Abs
Food Lion Vegetable Oil
0.2 (Soybean) New 0.1 Match:99.09 0.0
Abs
Food Lion Vegetable Oil
0.2 (Soybean) Used 0.1
Match:98.94
Abs
1.0 SOYBEAN OIL 0.5 Match:98.43
3500
3000
2500 Wavenumber
2000
1500
1000
(cm-1)
Abs
Figure 33 Low contact pressure ATR infrared spectrum of the yellow contamination (top spectrum) along with the three best library matches.
0.10
Yellow contamination
0.05
Abs
1.0 Pullulan P2000 0.5 Match:73.51
Abs
1.0 Pullulan P800 0.5 Match:72.87
Abs
1.0 a-Cyclodextrin .H2O 0.5 Match:72.20
3500
3000
2500
2000
1500
1000
Wavenumber(cm-1)
Figure 34 High contact pressure ATR infrared spectrum of the yellow contamination (top spectrum) along with the three best library matches.
better characterize the materials giving rise to the contaminant spectrum shown in Figure 34, selected regions of the higher contact pressure ATR spectrum were searched against the library database. When the region from 4,000 to 2,000 cm1 was searched, the closest match obtained was to coconut oil diethanolamide, a
642
Abs
James D. Rancourt et al.
0.10 0.05
Abs
Abs
1.0
Abs
Yellow contamination
0.5
Coconut oil diethanolamide Match:96.16
1.0
Coconut oil diethanolamide
0.5
Match:96.12
1.0
Oleic acid diethanolamide
0.5
Match:96.12
3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 35 High contact pressure ATR infrared spectrum of the yellow contamination (top) along with the three best library matches for a search confined to the region 4,000–2,000 cm1.
nonionic surfactant (see, Figure 35); amides exhibit a strong nC ¼ O absorption band near 1,650 cm1. The absorption band evident at about 1,750 cm1 due to nC ¼ O and the nCH absorptions in the region 3,100–2,800 cm1 match well those of the vegetable oil, the liquid portion of the sample. When the spectral search was limited to the region 1,700–1,500 cm1 (Figure 36), the best matches were to the library spectra of hydrated inorganic pigments. All these data taken together indicate that this contaminant is a combination of several materials. To analyze the green contamination on the small cups, the residue was removed using a micropipette and was placed onto a glass slide prior to recording its ATR spectrum, which is shown in Figure 37. The spectrum is shown together with the optimum-quality matches, which comprise materials such as an oil, a wax, and a defoamer. At the absorbance intensity recorded, the ATR spectrum recorded has all features associated with a saturated aliphatic hydrocarbon. The green residue from the large cups was a hard solid, so a portion was actually cut from the cup. The specimen was positioned in the FTIR-ATR microsampling accessory and the ATR crystal brought into contact with the contaminant. Residue from the contaminant transferred to the ATR crystal. The spectrum that was acquired from the transferred material is shown in Figure 38. The matches for this material to those in the library are similar to those for the small cup and include oils or other processing aids. The ATR infrared spectrum of the green contamination on the large cup is essentially identical with that of the ATR spectrum recorded from the contamination present on the small cup.
Abs
Failure, Defect, and Contaminant Analysis
643
Yellow contamination
0.10 0.05
Abs
0.00 Hoover 202-RS Match:93.46 Type: Inorganic Pigment
0.5
Abs
1.0
Hoover 512-BU Match:93.16 Type: Inorganic Pigment
0.5
Abs
1.0
Zinc Phosphate ZP Match:92.68 Type: Inorganic Pigment
0.5
3500
3000
2500
2000
1500
1000
Wavenumber(cm-1)
Figure 36 High contact pressure ATR infrared spectrum of the yellow contamination (top) along with the three best library matches for a search confined to the region 1,700–1,500 cm1.
Abs
0.2 0.1
Abs
1.0
Abs
Mineral oil + lanolin alcohol Match:98.24
0.5 1.0 0.5 1.0
Abs
Green contamination
0.5
PTFE SST-3K Match:98.18 Type: Additive - Wax Dapro DF-911 Match:98.07 Type: Additive - Defoamer
3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 37 ATR infrared spectrum of the green contamination on the small cup (top) along with the three best library matches.
In conclusion, the yellow contamination appears to be a mixture of materials, their infrared spectra suggesting that they are primarily a vegetable oil and pullulan, with possibly a surfactant and maybe an inorganic pigment also being present. The green residue is consistent with a saturated aliphatic hydrocarbon, such as a processing aid or an oil.
644
James D. Rancourt et al.
Abs
Green contamination
0.1
Abs
0.0 1.0
Match:98.09
0.5
Abs
1.0 0.5
1.0 Abs
Colloid 643
0.5
Type: Additive - Defoamer Mineral oil + lanolin alcohol Match:97.92
Mineral Seal Oil Match:97.30
3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 38 ATR infrared spectrum of the green contamination on the large cup (top) along with the three best library matches.
2.2.7 Case study B7: Consumer products, extruded plastic sheeting A manufacturer of extruded plastic sheeting had been experiencing problems with small contaminants appearing in their polypropylene-polyethylene (PP-PE) extruded sheets. The source of this contamination needed to be determined in order to overcome the problem. Several sheets containing particles were submitted for investigation, as well as some isolated particles taken from an extruder breaker plate. ATR-FTIR spectroscopy was initially used to examine these samples. The first specimens analyzed were the isolated particles from the extruder breaker plate. A particle was contacted by a Si ATR crystal, and its ATR spectrum recorded, which is shown in Figure 39 along with the closest three spectral search library matches. This sample spectrum matches most closely with that of a polyetherimide. Although the match quality is not high, the sample and polyetherimide library spectra are quite similar, particularly in the fingerprint region below 2,000 cm1. The two polyetherimide library spectra, shown in Figure 39, were each prepared by casting a film from dimethyl formamide (DMF) onto a KBr plate. It is most likely that the additional peak occurring near 1,650 cm1 seen in the two library spectra is attributable to residual DMF, traces of which can be very difficult to remove. This peak is not evident in the ATR spectrum recorded from the isolated particle. Following this, attempts were made to remove a particle from the extruded plastic sheeting. When a particle was finally isolated, applying pressure with the ATR crystal resulted in cracking of the particle, so a representative spectrum could not be obtained. This brittle behavior usually indicates that the sample is inorganic in nature.
Failure, Defect, and Contaminant Analysis
645
Abs
0.0 1.0 POLYETHERIMIDE #1 Match:84.30 0.5
Abs
0.2
1.0 POLYETHERIMIDE #2 Match:69.61 0.5
Abs
Abs
Extracted Particles; ATR
1.0 Polyester, tere- & isophthalic acids Match:64.46 0.5
3500
3000
2500 Wavenumber
2000
1500
1000
(cm-1)
Figure 39 ATR spectrum of a particle from the extruder breaker plate (top) along with the three closest library matches.
Based on these preliminary investigations, SEM-EDS was used to identify the particles embedded in the sheets. A particle was isolated from the extruded plastic sheeting and analyzed. Figure 40 shows an SEM micrograph at 14,500
magnification of the particle studied. This specimen is quite small, on the order of 10 mm in diameter. The EDS results are summarized in Table 11 for both this particle and for the polymeric matrix material from which it was harvested. As expected, the EDS data set indicates that the polymeric matrix material (the PE-PP blend) is composed only of carbon (hydrogen is not detectable by this method). The particle, however, appears to be composed mainly of aluminum and oxygen along with small amounts of copper. The ratio of aluminum to oxygen is consistent with the chemical formula for aluminum oxide (Al2O3). The SEM-EDS results are consistent with aluminum oxide and traces of copper as the primary constituents of the particulate contamination. (Al2O3.3H20 is a commonly used fire-retardant additive in polymeric products.) In conclusion, the particles from the extruder breaker plate were identified as being polyetherimide. The particles in the polymeric matrix, however, appear to be inorganic in nature, containing aluminum and oxygen, as aluminum oxide, with traces of copper.
2.2.8 Case study B8: Consumer products After a switch to a new poly/(vinyl chloride) (PVC) resin, a film residue was noted on the polished laminating plates used by a consumer product manufacturer. This residue needed to be identified so that the source of the contamination could be determined and eliminated.
646
James D. Rancourt et al.
Figure 40 SEM image at 14,500 magnification, of a particle removed from an extruded plastic sheet.
Table 11 Summary of EDS results for the polymeric matrix and the particle harvested from the extruded plastic sheeting Element
Weight percent in matrix
Weight percent in particle
Carbon Oxygen Aluminum Copper
100 ND ND ND
ND 46.1 52.4 1.5
Note: ND, not detected.
Si element ATR-FTIR spectroscopy was used to analyze this residue, and its spectrum, along with the closest library matches, are shown in Figure 41. The absorbance of this residue is low as a consequence of the thin layer present on the plate. This makes matching the sample spectrum with a reference spectrum somewhat difficult. The closest matches extracted from the library interrogated are to ester-based plasticizer materials, which is consistent with a phthalate-plasticized PVC. A more specific identification could have been made with further testing such as subjecting the residue to GC-MS analysis, but the information suggested by the ATR-FTIR analysis was, in this case sufficient.
Failure, Defect, and Contaminant Analysis
647
Abs
Residue, ATR
0.05
Abs
Abs
Abs
0.00 1.0
Paraplex G-60
0.5
Match:88.96 Type: Additive - Plasticizer
1.0
Byk Anti-Terra U
0.5
Match:85.31 Type: Additive - Surfactant
1.0
Di-2-Ethylhexyl Azelate
0.5
Match:84.04 Type: Additive - Plasticizer
3500
3000
2500 2000 Wavenumber (cm-1)
1500
1000
Figure 41 Si ATR spectrum for the residue on the polished metal plate (top) along with the three closest library matches.
2.3 Section C: Failure analysis 2.3.1 Case study C1: Medical products This case study involved medical diagnostic parts manufactured from PC resin, which were beginning to break too easily. To determine the cause of the failure, a good sample was submitted for comparison to a cracked part. Two possible causes for the failures were postulated. These include brittleness due to an excess level of filler, or the presence of voids due to insufficient drying of the resin prior to molding. The level of filler was measured using TGA. A portion of each sample was heated from room temperature to 9001C at a rate of 151C/min in air. The two PC samples yielded nearly identical TGA traces, as seen in Figure 42. In both cases, there appears to be negligible amount of filler, based on the fact that the mass remaining at the conclusion of the test was near zero. This implies that a filler component was not a possible contributing factor to the cracking. If the resin were insufficiently dried, the moisture present could cause voids within the molded part. This happens when the water evaporates and leaves open spaces. One effect of voids can be a lower bulk density. Bulk density was measured by the displacement method in accordance with ASTM D792 [7], and was found to be substantially equivalent for the two samples, as shown in Table 12. To look for small voids, SEM was used. For the cracked sample, a fracture surface was examined, while a cut surface of the good sample was studied. This test showed large differences between the two samples with the cracked part showing significant voids. Figure 43(a) shows an SEM micrograph for the good
648
James D. Rancourt et al.
Figure 42 TGA curves for the good sample (lower, thick line) and the cracked sample (upper, thin line).
Table 12
Summary of density measurements for two PC samples
Sample
Density (g/cm3)
Average
Standard deviation
Good
1.209 1.206 1.191 1.207 1.200 1.212
1.202
0.009
1.207
0.006
Cracked
(a)
(b)
(c)
270 μm
270 μm
270 μm
Figure 43 SEM micrographs, 37 magnification: (a) good sample; (b) cracked sample, showing voids; and (c) cracked sample, showing crack. (Scale bars indicate 270 mm.)
sample at a magnification of 37 . The surface looks essentially smooth, even at this high magnification. The cracked sample, by comparison, shows large voids and cracks (Figures 43(b) and 43(c)) at this same magnification (37 ). Voids are certainly present, but their small sizes are insufficient to lead to changes in the bulk density of the material. It seems clear, however, that the voids have
Failure, Defect, and Contaminant Analysis
649
contributed to the failure of the parts observed. Therefore, the cause of the cracking was determined to be insufficient drying, which was easily remedied in subsequent production runs.
2.3.2 Case study C2: Medical products A plastic tube, a critical component of a medical device made of PP, was breaking even with no force being applied. To determine the cause, both a broken part as well as a good part was analyzed. The first step of the analysis was to carefully examine the failed part using optical microscopy. The as-received part is shown at 7.5 magnification in Figure 44(a). Figures 44(b) and 44(c) show different views of the failure surface at 50 magnification. In both cases, it appears that there is some off-color foreign material present on the fracture surface. In Figure 44(b), the foreign material looked reddish in color, while Figure 44(c) shows only black particles. Figure 44(d) shows the area containing the reddish material at higher magnification (112.5 ). It cannot be determined whether this material was present before the failure or if it has been deposited into the fracture zone during the use of the
(a)
(b)
(c)
(d)
Figure 44 Optical micrographs of the failed part: (a) 7.5 magnification, (b) 50
magnification, (c) 50 magnification, and (d) 112.5 magnification.
650
James D. Rancourt et al.
Figure 45 SEM micrograph of the failed part, 60 magnification.
medical product or after the part broke. In examining the overall reason for the failure, these possibilities were all considered. The next step taken for this project was to examine the surfaces in more detail using much higher magnification. To that end, SEM was used to more closely examine the failure. Figure 45 shows an overview of the failure surface at 60 magnification. Using the analogy of a clock face, specific areas of the surface can be referenced. It can be noted (Figure 45) that the portion of the surface from about 06:00 to 11:00 showed a distinct line in the circumferential direction; in this image, the section that was still attached to the rest of the tube is found at about 03:00. Figure 46(a) shows a higher magnification (1,000 ) view of the region at about 07:00. In this image, a distinct circumferential line is seen through the cylinder. On the right hand side of this line, there appears to be very small particulate residue. This line continues around the part, at least up to the 10:00 position, as shown in Figures 46(b) through 46(e). Note that certain areas of the micrographs exhibit the silver paint that was utilized in the sample preparation for the SEM images. This silver material, an artifact from the sample preparation, is not related to the failure and has been noted on the images (Figures 46(c) and 46(d)). This line appears to represent a discontinuity in the material, which may imply a processing issue with the part. The area of the tear region (03:00) shows evidence of ductile failure, as shown in Figure 46(f). To perform the analysis it was necessary to sever this connection between the partially fractured tube pieces. Therefore, the two pieces of tubing were pulled apart. The expected result is the ductile failure that was in fact
(a)
(b)
(c)
(d)
(e)
(f)
(g)
(h)
Figure 46 SEM micrographs of the failed part at 1,000 magnification at approximately: (a) 07:00 position, (b) 08:00 position, (c) 09:00 position, (d) 09:30 position, (e) 10:00 position, (f) 03:00 position, (g) 02:00 position, (h) 01:30 position, (i) 01:00 position, (j) 12:30 position, (k) 12:00 position, and (l) 11:00 position. (Positions relate to a clock face with respect to the image shown in Figure 45.)
652
James D. Rancourt et al.
(i)
(k)
Figure 46
(j)
(l)
(Continued)
observed in this laboratory-induced fracture zone. The area adjacent to this tear (02:00 position) also shows ductile behavior (Figure 46(g)). However, there are also small voids present, which can be noted in the left hand side of the image in the flat region. These voids are also evident in Figure 46(h) and Figure 46(i). Figure 46(j) also shows voids, which seem to almost align radially. Some of these voids are also apparent in Figure 46(k). However, Figure 46(l) does not show any evidence of voids. It should be noted that this image was acquired from a zone near the beginning of the crack noted in Figures 46(a) through 46(e). Also, the flake-like material that appears in Figures 46(h) through 46(k) is from the silver paint used as a part of the specimen preparation and is not representative of the sample. In order to ascertain any differences in previous thermal history, DSC was used to compare the failed and good samples. Portions of each plastic tube were heated from 601C to 2001C at 151C/min. The resulting scans are shown in Figures 47 and 48, respectively. Both samples exhibit nearly identical melting peaks and onsets of melting, which indicates that the resins are the same. However, the broken sample has less crystallinity than the good part (44.12 J/g versus 56.47 J/g) as measured by the normalized melting peak area. This points to a difference in thermal history that has affected the degree of crystallinity. Both samples were also analyzed using TGA to verify that the filler levels were the same. It was reported that each part contained 20% barium sulfate and
Failure, Defect, and Contaminant Analysis
653
0.5
Heat Flow (W/g)
0.0
130.04°C 44.12J/g
-0.5
-1.0
-60
146.63°C
-10
Exo Up
40
90
140
190
Temperature (°C)
Figure 47 First heating cycle DSC scan of the failed part.
Heat Flow (W/g)
0.5
0.0
129.74°C 56.47J/g
-0.5
-1.0
-1.5 -60 Exo Up
146.50°C -10
40
90
140
190
Temperature (°C)
Figure 48 First heating cycle DSC scan of the good part.
1% titanium dioxide. In Figures 49 and 50, it can be seen that the residue remaining at 9001C, which would correspond to the inorganic filler content, is about 18.8% for both samples. The onset of the degradation was found to be slightly lower for the failed sample than the good sample (4091C versus 4261C), which might imply that the failed sample lacks some stabilizer. Finally, both samples were analyzed using ATR-FTIR spectroscopy. The Si ATR crystal was brought into contact with the sample, and spectra recorded. Figure 51 compares the spectra. Based on the excellent match factor between the spectra of the two samples (99.8%) and visual comparison of these two spectra,
654
James D. Rancourt et al.
Figure 49 TGA scan of the failed part.
Figure 50 TGA scan of the good part.
there are no significant differences apparent between the compositions of the two samples. In conclusion, no significant differences in the material composition or filler level were observed. A difference was noted between the good and failed part,
Failure, Defect, and Contaminant Analysis
655
Good part, ATR
Abs
0.4 0.3 0.2 0.1 0.0
Failed part, ATR
Abs
0.4 0.3 0.2 0.1 0.0 3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 51 ATR infrared spectra of the good part (top) and the failed part (bottom).
with the failed part having a slightly lower onset of degradation. This may indicate that a stabilizer is absent or present at lower levels. The melting temperatures were essentially identical for the two parts. Processing differences were also observed. It was noted, from optical microscopy, that there is apparently a residue present on the failure surface of the failed tube. SEM shows that this fracture surface also exhibits small voids as well as a larger crack along the circumference of nearly half the plastic tube. Both of these features may result from non-optimized processing conditions. In addition, it was found that the degree of crystallinity, as determined from DSC, differed substantially between the good and failed plastic parts, suggesting a difference in the thermal history, and thus processing, of the tubes. These data taken together point towards a problem with the processing of the material, which led to the failures.
2.3.3 Case study C3: Medical products A catheter sample, produced by a medical components manufacturer, was breaking and was therefore analyzed to determine its composition (catheter sample 1) and to compare its composition with the composition of other catheter products (catheter samples 2 through 6), some of which were not failing. Firstly, catheter sample 1 was dissolved in deuterated trifluoroacetic acid, and the solution analyzed by 1H NMR spectroscopy. The 1H NMR spectrum of the sample is shown in Figure 52. The peaks at 1.16 ppm, 2.56 ppm, and 3.40 ppm are consistent with a polyamide-12 (PA-12) structure. The signal at 3.58 ppm can be attributed to tetramethylene glycol (TMG) protons adjacent to the ether linkages. The signal at 1.60 ppm is composed of overlapping resonances from both components. The smaller peaks are most likely due to polymer end groups or protons at the junction of two blocks; the material is an amide–ether block
656
Figure 52 Table 13
James D. Rancourt et al.
1
H NMR spectrum of catheter sample 1.
Summary of 1H NMR results for catheter sample 1 Mole percent
Weight percent
TMG
PA-12
TMG
PA-12
36.17
63.83
20.19
79.81
copolymer, comprising blocks of PA-12 and TMG. Through comparison of the peak integrals for the components, it is possible to determine the relative ratio of PA-12 and TMG blocks. These results are shown in Table 13. The composition of the test sample was compared to literature values for commercial PA-12/TMG block copolymers marketed under the trade name PEBAXt. PEBAXt 5533 typically has a PA-12 content of 62 wt%, and PEBAXt 6333 has a PA-12 content of 76 wt%. From the NMR data, the test sample has a composition most similar to PEBAXt 6333. Secondly, the five additional catheter samples (2 through 6) were analyzed using 1H NMR spectroscopy to provide a direct comparison of these samples to the results for catheter sample 1. Approximately 30 mg of each additional sample was dissolved in 1 mL of deuterated 2,2,2-trifluoroacetic acid, and these solutions were analyzed using 1H NMR analysis. The 1H NMR spectra of all five of these
657
Failure, Defect, and Contaminant Analysis
Table 14
Summary of NMR results for catheter samples
Catheter sample
1 2 3 4 5 6
Mole percent
Weight percent
TMG
PA-12
TMG
PA-12
36.17 43.72 55.71 38.80 37.14 55.79
63.83 56.28 44.29 61.20 62.86 44.21
20.19 25.75 35.97 22.06 20.88 36.04
79.81 74.25 64.03 77.94 79.12 63.96
catheters had spectra that were similar to that of catheter 1 and were consistent with the spectrum expected for a PEBAX resin. The composition ratio of each of the copolymers was determined by comparison of the integrated intensity ratio of the TMG signal at 3.58 ppm to those of the polyamide signals at 2.56 ppm and 3.40 ppm. The copolymer composition results are summarized in Table 14. As mentioned above, the composition of catheter sample 1 was consistent with PEBAX 6333t. Similar results were obtained for catheters 2, 4, and 5, as shown in Table 14. By contrast, catheter samples 3 and 6 appear to be composed of PEBAX 5533t. Therefore, it was concluded that the breaking catheters were made from a different material.
2.3.4 Case study C4: Medical products In another catheter failure study, two samples of multi-layer catheters were tested. One catheter was breaking while the other was known to be a ‘‘good’’ sample. The catheters were freeze-fractured in order to obtain a cross-section view for SEM analysis, which was used to determine the construction of the catheter layers. ATR-FTIR spectroscopy was undertaken to identify the polymers used in the multi-layer catheter samples. Sample preparation for both catheter samples was the same. A catheter section, approximately 2.5 cm long, was cut from the bulk catheter using scissors. The section was submerged in liquid nitrogen and fractured using tweezers. One-half of the fractured section was mounted onto an aluminum SEM specimen stage using conductive carbon double-sided tape. The mounted sample was sputter coated with gold/palladium to a nominal thickness of 15 nm. As stated previously, sputter coating prevents the sample from charging by ensuring the surface of interest is conductive and thereby assures that the SEM image depicts the surface topography. Figure 53 shows a SEM micrograph of the catheter cross-section at 350
magnification. Two different layers are clearly evident. Figures 54(a) and 54(b) show micrographs of the outer layer at 2,500 and inner layer at 7,000
magnification, respectively. Five layer thickness measurements were acquired from each region, depicted in Figures 54(a) and 54(b), in order to determine the thickness of the outer catheter layer and the construction of the inner catheter
658
James D. Rancourt et al.
A B
C D
Figure 53 Cross-section of catheter sample 1 at 350 magnification. Four representative areas that were analyzed by FTIR are indicated by arrows A, B, C, and D.
Outer layer
Inner layer
(a)
(b)
Figure 54 Catheter sample 1 cross-section: (a) outer layer cross-section, 2,500 magnification and (b) inner layer cross-section, 7,000 magnification.
layer. The outer catheter layer measured 49.971.7 mm. Higher magnification of the inner layer revealed two layers, as indicated in Figure 54(b). The inner and outer portions of the inner catheter layer are 7.370.2 and 16.170.6 mm thick, respectively. Figure 55 shows a micrograph at 350 magnification of a cross-section of the second catheter. Two distinct catheter layers are evident in Figure 55 similar to those in Figure 53. Figures 56(a) and 56(b) show micrographs of the outer and inner catheter layers at 2,500 and 7,000 magnification, respectively. Five measurements were acquired from each region in Figures 56(a) and 56(b) to
Failure, Defect, and Contaminant Analysis
659
A
B
C
D
Figure 55 Catheter sample 2 cross-section at 350 magnification. Four representative areas that were analyzed by FTIR are indicated by arrows A, B, C, and D.
Outer layer
Inside layer
(a)
(b)
Figure 56 Catheter sample 2 cross-section: (a) outer layer cross-section, 2,500
magnification and (b) inner layer, 7,000 magnification.
measure the thickness of the outer catheter layer and the construction of the inner catheter layer. The outer catheter layer measured 59.870.3 mm. Higher magnification of the inner layer revealed two layers, as indicated in Figure 56(b). The inner and outer portions of the inner layer are 9.870.5 and 9.370.3 mm thick, respectively. ATR-FTIR spectroscopy was conducted at four locations on sample 1 and sample 2 as indicated on Figures 53 and 55, respectively The outer surface of the outer catheter layer (A) The inner surface of the outer layer (B)
660
James D. Rancourt et al.
The outer surface of the inner layer (C) The inner surface of the inner layer (D). The ATR-FTIR spectra of areas A and B recorded from the cross-section of catheter sample 1 were essentially identical and most closely matched by library spectra of nylon samples. Typing a nylon, as for example, 6, 6.6, or 11, solely from its infrared spectrum is problematic, owing to crystallinity effects [8]; further evidence is required from a DSC and/or NMR analysis. Notwithstanding, the ATR-FTIR spectra recorded from areas A and B show that the outer layer is homogeneous and made essentially of a single polyamide material. Also evident in both spectra is a weak nC ¼ O absorption band, not attributable to nylon, occurring near 1,740 cm1. The ATR-FTIR spectrum recorded from area A of catheter sample 1 is shown in Figure 57. A similar conclusion was reached from an examination of areas A and B from the cross-section of catheter sample 2, although from the infrared spectrum the nylon type appeared to be different from that used in catheter sample 1. The ATR-FTIR spectrum recorded from area A of catheter sample 2 is shown in Figure 58. Figures 59 and 60 show the ATR-FTIR spectra recorded from areas C and D, respectively, from the cross-section of catheter sample 1. Both spectra show features that indicate that each is essentially a polyethylene. The shoulder seen at 2,960 cm1 (due to terminal methyl groups in the branching) in Figure 59 indicates that the polymer is probably a low-density polyethylene (LDPE). Other weak absorption bands are also evident in this spectrum between 1,800–1,600 cm1 and 1,300–1,000 cm1, which are not attributable to polyethylene. These may well indicate it is a copolymer or contains an additive. The sharp well-resolved doublet at 730/720 cm1 evident in the infrared spectum of Figure 60 and lack of shoulder at 2,960 cm-1 indicate that this layer is probably
Absorbance
0.10
Outer surface, outside layer
0.08
0.06
0.04
0.02
0.00 4000
3500
3000
2500
2000
Wavenumber
(cm-1)
1500
1000
Figure 57 FTIR-ATR spectrum acquired from the outer surface of the outer layer of catheter sample 1, Area A.
Failure, Defect, and Contaminant Analysis
0.09
661
Outside surface, outer layer
0.08
Absorbance
0.07 0.06 0.05 0.04 0.03 0.02 0.01 0.00 4000
3500
3000
2500 2000 1500 Wavenumber (cm-1)
1000
500
Figure 58 FTIR-ATR spectrum acquired from the outside surface of the outside layer of catheter sample 2, Area A.
Outside surface, inside Layer
0.12
Absorbance
0.10 0.08 0.06 0.04 0.02 0.00 4000
3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 59 FTIR-ATR spectrum recorded from the outside surface of the inside layer of catheter sample 1, Area C.
a HDPE. It is likely therefore that this inner layer is formed from co-extruded layers of a LDPE, (or ethylene copolymer), and a HDPE. Library searches of the spectra of Figures 59 and 60 yielded closest matches of the types described. Figures 61 and 62 show the ATR-FTIR spectra recorded from areas C and D, respectively, from the cross-section of catheter sample 2. The infrared spectra from both areas, C and D, are spectrally matched closest by a library spectrum of a polyethylene. (Both the recorded spectra show weak additional absorption bands in the region 1,700–1,500 cm1.) The ATR-FTIR spectrum recorded from
662
James D. Rancourt et al.
0.16
Inside surface, inside layer
0.14
Absorbance
0.12 0.10 0.08 0.06 0.04 0.02 0.00 4000
3500
3000
2500
2000
Wavenumber
(cm-1)
1500
1000
Figure 60 FTIR-ATR spectrum recorded from the inside surface of the inside layer of catheter sample 1, Area D.
0.20 0.18
Outside surface, inside Layer
0.16
Absorbance
0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 4000
3500
3000
2500
2000
1500
1000
500
Wavenumber (cm-1)
Figure 61 FTIR-ATR spectrum recorded from the outside surface of the inside layer of catheter sample 2, Area C.
the outer surface of the inner catheter layer (area C) shows the presence of an absorption shoulder at 2,960 cm1, indicating that this is possibly a LDPE type. The spectrum acquired from area D (the inside surface of the inner layer) showed a relatively weaker absorbance at 2,960 cm1. Based on the fracture mode of the inner catheter material and the slight difference in the two infrared spectra at 2,960 cm1 it is likely that this catheter layer is a co-extruded bi-layer as well.
Failure, Defect, and Contaminant Analysis
0.20
663
Inside surface, inside layer
0.18 0.16
Absorbance
0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 4000
3500
3000
2500
2000
1500
1000
50
Wavenumber (cm-1)
Figure 62 FTIR-ATR spectrum recorded from the inside surface of the inside layer of catheter sample 2, Area D.
In conclusion, both catheters appear similar in terms of construction and polymeric materials, although the infrared spectra suggest that a different nylon may have been used for each, and that the inner polyethylene-based bi-layers have been co-extruded from different polyethylenes. Another variation noted was the slight difference in thickness of layers between the two samples.
2.3.5 Case study C5: Packaging 2.3.5.1 Optical microscopy and SEM. Failure analysis of two samples of plastic packages was required. The packaging consisted of a clear plastic film that was heat-sealed to an opaque white backing. The backing film was white-colored oriented polyester, according to information provided by the supplier. Initial visual examination of a ‘‘bad’’ package indicated that the white film itself might actually be a multi-layer construction with a clear, unfilled layer co-extruded onto a white-pigmented layer. The package was designed to be opened by peeling apart the clear (front) and white (back) films. The package marked ‘‘bad’’ was from material that was returned from the field with the complaint that the white film is brittle and breaks when one attempts to open the package. Two packages marked ‘‘good’’ were from retained inventory and were reportedly the same age as the ‘‘bad’’ sample. Both samples had been sterilized using gamma radiation. The white backing films from the ‘‘good’’ and ‘‘bad’’ packaging samples were analyzed using SEM, ATR-FTIR spectroscopy, and TGA. Scanning electron micrographs of the ‘‘bad’’ white film fracture surface were acquired (Figure 63). An optical micrograph of the fracture surface is shown in Figure 64. The micrographs show that the white film is in fact a multi-layer construction. Examination of the film was also performed using optical stereomicroscopy.
664
James D. Rancourt et al.
4 3
3 4 2
2 3 1 1
Figure 63 Scanning electron micrographs of the failure surface of the white backing layer of the ‘‘bad’’ packaging sample. Four layers were clearly visible in the SEM images. They are labeled as follows: (1) outer clear polyester layer, (2) middle opaque polyethylene layer, (3) EVA heat seal layer, and (4) clear top film of package.
1
2 3
Figure 64 Optical micrograph of the fracture surface of the ‘‘bad’’ film. (1) Clear outer polyester layer, (2) middle opaque polyethylene layer, and (3) EVA heat seal layer.
Identification of individual film layers was performed using ATR-FTIR. The outside layer labeled ‘‘1’’ was optically clear and was identified as an aromatic polyester; most likely poly(ethylene terephthalate) (PET) or an ethylene terephthalate/isophthalate copolymer. Beneath the outer polyester layer is a white opaque layer, labeled ‘‘2’’ in Figure 63, which was identified as polyethylene. The polyethylene layer shows features that are characteristic of brittle failure. The direction of applied stress during failure was likely in the vertical direction in the SEM images in Figure 63.
Failure, Defect, and Contaminant Analysis
665
The polyethylene layer shows a series of fault lines that run perpendicular to the direction of applied stress. The fracture surface of the polyethylene is sharp and jagged, and shows no signs of elongation or ductility. Beneath the polyethylene layer ‘‘2’’ was a thin layer (‘‘3’’) that was identified as ethylene/vinyl acetate copolymer (EVA). The EVA layer did show evidence of ductile failure in the SEM images. Pieces of ‘‘good’’ and ‘‘bad’’ white film were cut from each package and force was applied manually until the strips failed. In the ‘‘good’’ film, the center polyethylene layer exhibited significant elongation and failed in a ductile manner. The center polyethylene layer of the ‘‘bad’’ film showed very little ductility, and failed in a brittle manner. The number of layers and the approximate thickness of each layer were determined from SEM images of freeze-fractured cross-sections of the films (Figure 65). A diagram of the apparent film construction is presented in Figure 66. The composition and thickness of each layer are shown in Table 15. The center opaque polyethylene layer and the EVA heat seal layer could not be differentiated in the SEM images of the freeze-fractured cross-section of the
C B A
C B A
(a)
(b)
A C B C
D
(c)
(d)
Figure 65 SEM images: (a) and (b) cross-sections of the ‘‘good’’ package white backing film, (c) and (d) cross-sections of the ‘‘bad’’ package white backing film. (A) Outer clear polyester layer, (B) tie layer, (C) middle opaque polyethylene layer, and (D) EVA heat seal layer.
666
James D. Rancourt et al.
A B
C
D
Figure 66 Schematic of the apparent construction of the white backing film: (A) Outer clear polyester layer, (B) tie layer, (C) middle opaque polyethylene layer, and (D) EVA heat seal layer.
Table 15
Summary of film construction
Layer in Figure 65
Description
A B C D C+D
Outer clear polyester layer Tie layer (unknown composition) Opaque polyethylene Inside clear EVA heat seal layer (Sum of polyethylene and EVA)
Thickness (mm) ‘‘Good’’ sample
‘‘Bad’’ sample
11 3
11 1.5 65 11 76
76
Note: Not measured for ‘‘good’’ sample.
‘‘good’’ sample. However, the total thickness of polyethylene plus EVA was the same for both samples. The only difference in layer thickness between samples occurred in the tie layer between the polyester and opaque polyethylene layers. The tie layer was twice as thick for the ‘‘good’’ sample compared to the ‘‘bad’’. Comparison of the fracture surface of the opaque polyethylene layer between the ‘‘good’’ sample (Figures 65(a) and 65(b)) and the ‘‘bad’’ sample (Figures 65(c) and 65(d)) showed a definite difference in appearance. The ‘‘good’’ sample fracture surface showed evidence of ductility in the polyethylene layer. The polyethylene fracture surface of the ‘‘bad’’ sample showed less elongation and had a cleaner appearance that is characteristic of brittle failure.
2.3.5.2 FTIR spectroscopy. The ATR-FTIR spectra of the outside surface of the ‘‘good’’ and ‘‘bad’’ white films are shown in Figures 67 and 68, respectively.
Failure, Defect, and Contaminant Analysis
667
Abs
Outside surface 0.5
Abs
0.0 1.0 0.5
Abs
1.0 0.5
Abs
1.0 0.5
Polyester, tere- & isophthalic acids Match:82.37
Polyester, tere- & isophthalic acids Match:81.92
Polyester, tere- & isophthalic acids Match:79.60
3500
3000
2500 Wavenumber
2000
1500
1000
(cm-1)
Figure 67 ATR-FTIR spectrum of the outside (back) surface of the white backing film of the ‘‘good’’ package sample.
Abs
1.0 0.5
Abs
0.0 1.0 0.5
Abs
1.0 0.5 1.0 Abs
Outside shiny surface
0.5
Polyester, tere- & isophthalic acids Match:82.53
Polyester, tere- & isophthalic acids Match:82.01
Polyester, tere- & isophthalic acids Match:79.79
3500
3000
2500
2000
1500
1000
Wavenumber (cm-1)
Figure 68 ATR-FTIR spectrum of the outside (back) surface of the white backing film of the ‘‘bad’’ package sample.
The three closest matches from spectral library searching are shown below each sample spectrum. The library search results indicate that the clear outer film is an aromatic polyester. This is most likely PET or an ethylene terephthalate/ethylene isophthalate copolymer. No significant spectral
668
James D. Rancourt et al.
0.8 Inside surface, “good” film Abs
0.6 0.4 0.2 0.0 0.8 Inside surface, “bad” film Abs
0.6 0.4 0.2 0.0
Ethylene/vinyl acetate copolymer Cap #12 VA content 14% (0.031")
Abs
0.4 0.2 0.0 3500
3000
2500 Wavenumber
2000
1500
1000
(cm-1)
Figure 69 ATR-FTIR spectrum of the heat seal surface of the ‘‘good’’ white film (top), the heat seal surface of the ‘‘bad’’ white film (middle), and the library spectrum of an ethylene/ vinyl acetate copolymer (bottom).
differences were noted between the spectra of the outer surfaces of the ‘‘good’’ and ‘‘bad’’ films. Figure 69 shows the ATR-FTIR spectra of the inside heat seal layer of the white film from both the ‘‘good’’ and ‘‘bad’’ packages. A library spectrum of an EVA copolymer is also shown for comparison. The heat seal layer is identified as EVA, based on the position of peaks in the sample spectra compared to the library EVA spectrum. The heat seal layer appears to have a lower vinyl acetate content compared to the library spectrum, which was acquired from a 14% vinyl acetate copolymer. There were no significant spectral differences between the spectra of the ‘‘good’’ and ‘‘bad’’ samples. The ATR-FTIR spectrum of the middle opaque polyethylene layer of the ‘‘bad’’ sample is shown in Figure 70. This spectrum was acquired from the fracture surface where the outer polyester film and tie layer delaminated from the polyethylene layer. The highest-scoring library match in Figure 70 indicates that the middle layer is a polyethylene with a low branch content, most likely a HDPE or a LLDPE, although a much more detailed spectral analysis would be required to confirm this. Figure 71 compares the 2,000–1,000 cm1 FTIR spectral region for the heat seal layers of the ‘‘good’’ and ‘‘bad’’ films, and the center opaque polyethylene layer for the ‘‘bad’’ film. Of particular interest is the carbonyl region between approximately 1,800 and 1,650 cm1. The two heat seal surface spectra show mainly the vinyl acetate ester carbonyl band at 1,740 cm1. For the middle polyethylene layer of the ‘‘bad’’ film, the shape and position of the carbonyl band is consistent with oxidative degradation of polyethylene. The peak maximum at
669
Failure, Defect, and Contaminant Analysis
Abs
Outside dull surface
0.5
Abs
0.0 0.6
**Polyethylene High Density Cap #49 (0.020") Match:99.04
0.4 0.2
Abs
Abs
0.0 1.0
A-C 715 Match:96.19
0.5
Chemical Name: Polyethylene Type: Additive - Wax
1.0
Ampac Wax
0.5
Match:95.94 Chemical Name: Carnauba Wax 91%, Microcrystalline Wax 9% Type: Additive - Wax
3500
3000
2500
2000
Wavenumber
1500
1000
(cm-1)
Figure 70 ATR-FTIR spectrum of the middle polyethylene layer of the ‘‘bad’’ white film (top) and the three closest matches from a library search.
0.10 0.09 0.08
Absorbance
0.07 0.06 0.05 0.04 0.03 0.02 0.01 2000
1800
1600
1400
1200
1000
Wavenumbers (cm-1)
Figure 71 2,000–1,000 cm1 region ATR-FTIR spectra of the surface of the heat seal layer of the good film (dashed line), the surface of the heat seal layer of the ‘‘bad’’ film (dotted line), and the surface of the middle (opaque) layer of the ‘‘bad’’ film (solid line).
670
James D. Rancourt et al.
1,710 cm1 is indicative of ketone functional groups. Peak shoulders are seen at 1,775 cm1, 1,740 cm1, and 1,710 cm1, which are indicative of lactone, ester, and carboxylic acid carbonyl groups, respectively.
2.3.5.3 Thermogravimetric analysis. The ‘‘good’’ and ‘‘bad’’ film samples were analyzed using TGA in order to determine whether there was a significant difference in filler content between samples. An approximately 1 mg portion of film was placed in the platinum sample pan of the TGA microbalance, and the sample weight was recorded as the film was heated in air from 301C to 9001C at a heating rate of 151C/min. The TGA weight percent versus temperature plots are shown in Figures 72 and 73 for the ‘‘good’’ and ‘‘bad’’ samples, respectively. The residual weight percents (ash contents) at 9001C were 1.1% and 0.8% for the ‘‘good’’ and ‘‘bad’’ films, respectively. These values are not significantly different based on the measurement precision of the TGA microbalance. The residue percentages were surprisingly low for a filled polyethylene, considering that the polyethylene layer comprises about 70% of the film by volume. The residue probably represents white pigment (titanium dioxide), not a filler such as calcium carbonate. The brittleness in the polyethylene layer is, therefore, not the result of poor filler dispersion or an excessive filler content. 2.3.5.4 Conclusions. Based on the results of SEM, FTIR spectroscopy, and TGA analyses performed on the ‘‘good’’ and ‘‘bad’’ samples of white packaging film, the brittleness problem reported for the packages appears to have been caused primarily by degradation of the central opaque polyethylene layer.
Figure 72
TGA weight percent versus temperature plot for the ‘‘good’’ white film.
Failure, Defect, and Contaminant Analysis
671
Figure 73 TGA weight percent versus temperature plot for the ‘‘bad’’ white film.
The assumption is made that the ‘‘good’’ and ‘‘bad’’ samples were made from the same materials. The central polyethylene layer fails in a brittle manner in the ‘‘bad’’ sample, but exhibits considerable ductility in the ‘‘good’’ sample. The FTIR results indicate that the middle polyethylene layer has been oxidized in the ‘‘bad’’ sample. The ‘‘good’’ and ‘‘bad’’ film samples are very similar in terms of chemical composition and configuration of layers. It is likely that oxidative degradation of the polyethylene polymer has occurred during storage or shipping, breaking down the molecular weight of the polymer to the point where the integrity of the polymer is severely affected.
2.3.6 Case study C6: Packaging, medical device Several samples of medical device packaging were evaluated because of their premature failure. A white-colored polyethylene (PE) layer was degrading. Discussions with the client revealed that the polyethylene contained in the packaging is not stabilized against ultraviolet (UV) light, and that the packages are exposed to strong UV light during storage. These facts strongly suggest that UV degradation of the PE was the cause of the package failure. The packaging is mostly PE, but also has both an EVA and PET layers. Sections of several packages were tested by dilute solution viscometry in decahydronaphthalene at 1351C to determine if the failures are consistent with UV degradation. The top surface of each package was partially covered by a paper label. This label should have shielded the underlying film from UV exposure, and there should be a difference in the solution viscosity of material taken from the shielded center of the package and material taken from the UV-exposed edge. Sections from the center and edge of three samples were
672
James D. Rancourt et al.
tested. Good Sample 1 represents a sample that has not been subjected to exposure to strong UV light. Bad Sample 2 shows marked brittleness near the edge. Discolored Sample 3 shows brittleness and yellowing around the edge, but is not discolored in the center area protected by the label. The dilute solution viscometry results are presented in Table 16. Decahydronaphthalene is known to be a good solvent for PE, which is the layer of interest in this case. However, some of the film layers were not soluble in decahydronaphthalene, leading to uncertainty in the actual concentration of the test solutions. Consequently, the results are presented as specific viscosity, which is not concentration dependent. The bad and discolored samples showed much lower specific viscosities than the good sample, which corresponds to lower average molecular weight for the polyethylene layers in these samples. In all of the samples, the edge material did produce a lower value than the center of the sample. However, the difference between the edge and center of each sample is much lower than the difference between samples of different exposure conditions, which indicates that there is still significant degradation in the area under the label. A controlled exposure study was also performed on a sample (Sample 4) of film material. Sample 4 was divided into test sections that were subjected to controlled UV exposure according to ASTM D 4459 [9], and then tested for tensile strength according to ASTM D882 [10]. Separate samples were exposed to UV radiation for 250 h, 500 h, and 750 h. Five sections of each exposure sample were then tested for tensile strength, and the average and standard deviation for ‘‘tensile strength at break’’ and ‘‘elongation at break’’ are reported in Table 17. Table 16
Table 17
Sample
Description
Specific viscosity
1a 1b 2a 2b 3a 3b
Good, edge Good, center Bad, edge Bad, center Discolored, edge Discolored, center
0.345 0.353 0.218 0.279 0.075 0.083
Summary of tensile strength test results for Sample 4
UV exposure time (h)
0 250 500 750
Summary of dilute solution viscometry results
Tensile strength at break (psi)
Elongation at break (%)
Average
Standard deviation
Average
Standard deviation
5,640 4,260 3,860 2,490
482 436 123 614
54 21 10 1.9
16 14 3 0.5
673
Failure, Defect, and Contaminant Analysis
Table 18
Results of high-temperature GPC analysis
Sample
Run
Mn (g/mol)
Mw (g/mol)
Mz (g/mol)
Mw/Mn
1
1 2 Average
54,500 53,600 54,100
201,000 201,000 201,000
608,000 610,000 609,000
3.69 3.75 3.72
2
1 2 Average
17,100 16,800 17,000
43,600 42,900 43,300
92,300 89,300 90,800
2.55 2.55 2.55
The tensile strength at break decreases steadily with increased UV exposure. At the same time, the elongation at break also drops, which indicates that the material is less capable of stretching. Dilute solution viscometry testing of good and brittle packages confirmed that the brittle packages are experiencing degradation of molecular weight. Portions of samples that were not directly exposed to UV light showed slightly less degradation than portions that were directly exposed. Controlled UV exposure and tensile strength testing showed that the samples experience a loss in tensile strength and elasticity with UV exposure. Additional analysis of the molecular weight distribution of the polyethylene layer in the ‘‘good’’ versus ‘‘bad’’ packages was performed using high-temperature GPC. A portion of the white film from each package was heated in TCB containing 0.1% w/v of N-phenyl-2-naphthylamine as an antioxidant. The portion of the white film not covered by the label was sampled for the ‘‘bad’’ package sample. The ‘‘good’’ packages had no label. The nominal polymer concentration in solution was 2 mg/mL. The samples were filtered hot through 0.5-mm pore size glass fiber filters. TCB is a non-solvent for PET. Therefore, only the PE and EVA layers were dissolved. The middle PE layer accounted for about 80% of the film thickness. PET and EVA were minor components of the film. GPC analysis was performed in TCB at 1451C using refractive index (RI) detection. Molecular weight distributions of the samples were calculated relative to polystyrene calibration standards. The molecular weight averages (Mn, Mw, and Mz) as well as the polydispersity (Mw/Mn) are presented in Table 18. The GPC results indicate a drastic molecular weight reduction of the polyethylene layer of the white packaging film, confirming the hypothesis that the brittle failure is the result of degradation of the polyethylene.
3. SUMMARY From the case studies reported in this chapter, it has been shown that a systematic approach to failure analysis and contamination issues can be applied to a broad and diverse range of industrial problems. The use of techniques such as SEM, NMR, and FTIR can often provide information relevant to the cause of
674
James D. Rancourt et al.
failures in instances ranging from faulty automotive parts to breaking medical products. Note also that these same techniques can also be applied to deformulation or reverse engineering by using essentially the same methodologies. Other complementary methods, including DSC, TGA, ICP spectroscopy, Raman spectroscopy, XPS, and molecular weight analysis, are also commonly utilized in these instances.
REFERENCES 1 J.M. Chalmers and N.J. Everall, Qualitative and quantitative analysis of plastics, polymers and rubbers by vibrational spectroscopy. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007, pp. 1–67. 2 J. Schiers, Compositional and Failure Analysis of Polymers — A Practical Approach, Wiley, Chichester, 2000. 3 M. Claybourn, Infrared Spectroscopy of Polymers: Analysis of Films, Surfaces and Interfaces, Global Press, Chicago, 1998. 4 E. Smith and G. Dent, Modern Raman Spectroscopy: A Practical Approach, Wiley, Chichester, 2005. 5 Infrared Spectroscopy Atlas for the Coatings Industry, Federation of Society for Coatings Technology, Philadelphia, 1991. 6 D.W. Mayo, F.A. Miller and R.W. Hannah, Course Notes on the Interpretation of Infrared and Raman Spectra, Wiley, Hoboken, 2004. 7 D0792-00 Test methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement, Annual Book of ASTM Standards, Vol. 08.01 Plastics(I), ASTM International, West Conshohoken, 2007. 8 J.M. Chalmers, Spectra-structure correlations: Polymer spectra. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy: Principles and Practice, Wiley, Chichester, 2007, pp. 69–112. 9 D4459-99 Practice for Xenon-Arc Exposure of Plastics Intended for Indoor Applications, Annual Book of ASTM Standards, Vol. 08.02 Plastics(II), ASTM International, West Conshohoken, 2006. 10 D0882-02 Test Method for Tensile Properties of Thin Plastic Sheeting, Annual Book of ASTM Standards, Vol. 08.02 Plastics(I), ASTM International, West Conshohoken, 2007.
CHAPT ER
16 Surface Analysis John M. Chalmers and Robert J. Meier
Contents
1. Introduction 2. A Surface and Spatial Resolution 3. Adhesion 4. Polymer Degradation 5. Polymer Fracture 6. Characterizing Polymer Surfaces 7. Delamination 8. Cure 9. Closing Remark References
675 676 677 679 679 679 679 681 682 682
1. INTRODUCTION The surface of polymer products is important in many instances and indeed critical to many applications. Clearly a product’s appearance towards the ‘outside’ world is important, since that is how we see the material. Quite a few properties may matter, including such as colour, surface appearance like smoothness and reflectivity, adhesion, etcetera. The way the surface appears may be the result of polymer processing, e.g., extrusion, of degradation, e.g., oxidation, or deliberate modification to induce or enhance adhesion, or produce a matte or gloss finish. In addition, studying the surface of a material that has failed may reveal the reason of failure. Recently it has become part of the trade to make smart polymeric materials, including those having particular electrical properties, having surfaces that are water droplet repellent, having particular gas permeability functions, or other specific specialised demands. What one considers included in surface properties depends on what one considers the surface. (We are not in this chapter considering specific coatings per se that may be applied to achieve a particular effect or property). For adhesion Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00416-9
r 2008 Elsevier B.V. All rights reserved.
675
676
John M. Chalmers and Robert J. Meier
of or to a surface it is really the outermost atomic layers that are crucial, and molecular characterization analytical techniques such as X-ray photoelectron spectroscopy (XPS) (also known as ESCA, electron spectroscopy for chemical analysis) and secondary ion mass spectrometry (SIMS) are key tools. For optical appearance, taking into account that visible light penetrates further than the outmost atomic layer, optical spectroscopic techniques are worthwhile applying. Surface roughness (topography) as such may be studied using atomic force microscopy (AFM). Obviously, also the electron microscopies are excellent techniques that can be applied to surface-related issues. As the editors of this book, and authors of this chapter, our intended aim was wherever possible to look at polymer analysis from the point of view of using analytical competence (see Chapter 1) to address problem solving, so discussing in detail the individual analytical techniques here, as is the common thing to do when dealing with surface properties, is inappropriate. Looking at it from the point of view of a multi-technique problem-solving environment, rather than a specialist technique research laboratory, there are quite a few content overlaps with other chapters, so this chapter will serve largely as a concise overview and complement to these chapters. For instance, the presence of a surface contaminant that induces polymer failure can be considered part of Chapter 15, whereas polymer degradation has been treated extensively in other chapters (Chapters 10–12). Still other examples, looking at differences at the micrometer scale, may be covered by imaging techniques (e.g., vibrational spectroscopic (infrared (IR) and Raman), ESCA, time-of-flight-SIMS (ToF-SIMS) applied to cross-sections of the material, see, for example, Chapter 13. Therefore, as stated above, this is a brief chapter, where on the one hand we refer to other chapters wherever appropriate, and on the other hand will provide some additional specific examples.
2. A SURFACE AND SPATIAL RESOLUTION As already indicated above, what one may consider a surface depends on the property under consideration. Adhesion is very much an outer atomic layer issue, unless one is dealing with materials like fibreboard in which the polymer resin may also be involved in mechanical anchoring onto the wood particles. Gloss and other optical properties are related to the penetration depth of optical radiation. The latter depends on the optical properties of the material, but in general involves more than a few micrometer thickness and therewith much more than the outer atomic layers only. It is thus the penetration depth of the probing technique that needs to be suitably selected with respect to the surface problem under investigation. Examples selected for various depths (o10 nm, 10’s of nm, 100 nm, micrometer scale) have been presented in Chapter 10 of the book by Garton on Infrared Spectroscopy of Polymer Blends, Composites and Surfaces [1], where also non-IR techniques such as ESCA are mentioned. ESCA, which is one of the ultimate surface sensitive techniques, was developed by Kai Siegbahn [2], for which he was awarded a Nobel Prize in 1981. ESCA has a penetration
Surface Analysis
677
depth in the nanometer range and is generally applied when the outermost atomic region is of interest. Infrared and Raman spectroscopies have a depth resolution in the micrometer range. The depth profiling of polymers by vibrational (mid-infrared and Raman) spectroscopy was reviewed recently by Fredericks [3]. The limit of one to a few microns can be achieved with confocal Raman spectroscopy. In the commonly used infrared internal reflection spectroscopy (IR-IRS) technique (often referred to as attenuated total reflection, ATR) the depth probed is of the order of about 0.3–3 mm (being wavelength dependent); its Raman equivalent even allows for depth resolution down to 0.2 nm [4,5]. However the Raman internal reflection technique is not standard, and therefore rarely applied other than in an academic environment. More importantly, the available specialist practical experience is unlikely to be present. In the end, what matters obviously is whether the features of interest distinctly show up in the analytical data, e.g., in a spectrum or a map or image. Thus, even though IR is not ultimately a surface specific technique, when an outermost surface layer reveals characteristic absorption bands that are related to say a property such as adhesion, the technique can be a very valuable one and is extensively applied. Finally, it should be kept in mind that quantification is often problematic in surface analysis and characterization. Firstly because some techniques are not really suited for quantification, but also in cases such as infrared spectroscopy where one does not really know precisely how deep into the material one is probing. Although, there are many good examples of semi-quantitative applications that involve measuring relative band intensities that relate to changes in a surface property. However, for problem solving revealing qualitative differences is often sufficient information to be able to identify cause and move on to look for a potential solution. In practice, and this book was really intended to look from a practical problem-solving point of view, techniques like ESCA, SIMS and some of the imaging optical spectroscopies are, next to electron microscopy, the traditional and well-developed work-horses. Of course there are other techniques, such as Surface Enhanced Raman Spectroscopy (SERS), but despite its now already quite long history its application so far has remained cumbersome and therefore rather limited to use within academia. ESCA, despite probing the core electrons and therewith only revealing information from the neighbouring chemically bonded atoms through small shifts in core-electron-binding energies, is nevertheless the more often applied technique compared to Ultraviolet Photoelectron Spectroscopy (UPS), as the spectral intensities are much higher for ESCA.
3. ADHESION Adhesion or printability of polymeric surfaces, including films, is often promoted by plasma or glow discharge treatment. In particular for apolar (low surface energy) surfaces such as polyolefins this is a commonly applied procedure. As a practical industrial example, the adhesion behaviour of polypropylenes after
678
John M. Chalmers and Robert J. Meier
0.8 HI-PP SHI-PP HDPE
0.4
O-adh fraction
0.6
0.2
0.0 30
28
26
24
22
20
18
air/propane ratio
Figure 1 The ratio of the Oads/Ototal (‘adhesive’ oxygen/total oxygen at the surface of the flame) concentration as a function of the gas composition for three different polyolefin samples. The HDPE sample shows a relatively low ratio, compared with the SHI-PP (super high impact PP) that has a high Oads fraction, which reflects the differences in their adhesion behaviour. Roughly two out of three oxygen atoms on the modified SHI-PP surface are of the chemical type needed for adhesion [6]. Reprinted from Pijpers and Meier [6]. Copyright 2001, with permission of Elsevier.
flame treatment was studied [6]. By applying derivatization with dibromoketones to selectively probe the oxygen atoms involved in adhesion, a relation between this type of oxygen atoms and adhesion behaviour was established, see, for example, the results shown in Figure 1. Other problems in adhesion may be tackled by studying the surface of the material after fracture. Mass spectroscopic methods like SIMS may reveal transfer of molecular fragments from the one component towards the other one. Adhesion of, e.g., paint on polymeric materials such as in automotive bumper material may be poor because of silicon grease being present at the surface as a result of handling the bumper before applying the paint. By using ESCA such problems can be tackled easily and customer complaints can be refuted or accepted. Whereas ESCA and other surface specific techniques are often the obvious method of choice, IR-ATR may be a suitable technique when the composite material is heavily filled, and the IR radiation does not penetrate to far into the sample material. An advantage of, e.g., IR is that the sample can be investigated under ambient conditions rather than under a high vacuum, as required with techniques such as ESCA.
Surface Analysis
679
4. POLYMER DEGRADATION Polymer degradation may lead to various unwanted effects, including loss of gloss, strong colouration (e.g., during the degradation of poly(vinyl chloride) (PVC)), the appearances of cracks in the surface. Polymer degradation and the way this may be approached using analysis has already been extensively treated in three chapters in this book (Chapters 10–12).
5. POLYMER FRACTURE This topic has been mentioned in Section V, Failure, Defect and Contaminant Analysis, in Chapter 15, where a number of typical practical problem invetsigations were presented. Obviously the potential list of examples exhibiting different characteristics and requiring a different type of analysis is lengthy. When the sample is heterogeneous, e.g., a polymer blend or a composite, the study of the surface of a failed piece of material may reveal whether the problem is the interface of the components or that failure occurred within one of these. In particular in the case of crazing or necking orientation may have been induced, the way this can be analysed is discussed in Chapter 8.
6. CHARACTERIZING POLYMER SURFACES A series of examples involving either ESCA (or XPS) or SIMS applied to polymer surface analysis have been collected in the chapter entitled Surface Analysis in the volume by Kroschwitz [7]. Surface Mass Spectrometry applied to the field of polymer/additives has been extensively reviewed recently by Bart [8]. Recent developments have allowed for more detailed studies of polymer surface morphology by ESCA. Angle-resolved ESCA (ARXPS) allows for providing chemical compositions from shallower depths. By varying the angle of incidence different depths can be probed, and procedures have been developed to arrive at three-dimensional reconstruction of the surface. An example is shown in Figure 2, where a PVC/PMMA polymer blend has been analysed using such an approach [9]. With the development of high-resolution ESCA equipment and in particular the skilled experimentalist who is capable of suppressing line-broadening effects such as those arising from charging of the surface due to the electron beam being used, even such subtleties as trans-gauche conformational sensitivity can be probed, as was shown for the case of poly(ethylene terephthalate) [10] (see Figure 3).
7. DELAMINATION Many polymer products are constructed as laminated films, with each layer imparting a particular property to the end product, whether it be, for example, a
Figure 2 Volume visualization of the three-dimensional volume representing the PVCenriched phase of the polymer blend: (a) the whole volume rendered, (b) three orthogonal slices showing the interior of the volume, (c) single isosurface showing 5/95 PVC/PMMA composition of the blend, and (d) multiple isosurfaces displaying three compositions 5/95, 12/88, and 22/78 of the blend. Reproduced from Artyushkova and Fulghum [9]. Copyright 2005, with permission from Elsevier. 25
Counts x103
20
Biaxial film
15
1
Polymer melt
10 3
2
5
Spin cast film
0 292
290
288 286 Binding Energy [eV]
284
282
Figure 3 The C1s ESCA spectrum of two PET samples revealing the difference between a more crystalline sample exhibiting more trans CaC bonds in the glycol segment (biaxial film) and an amorphous sample rich in gauche CaC bonds (melt) in the spectral range near 286 eV. Figure reproduced from Beamson et al. [10]. Copyright 1996, with permission from Elsevier.
Surface Analysis
681
Figure 4 IR-ATR microscopy study of the plane of failure analysis of a polymer ID card. (a) Infrared spectra of the exposed surfaces at the initial point of delamination, in which a weak absorption band at ca. 930 cm1 can be observed in the upper spectrum that is not present in the lower spectrum; this indicates that the initial delamination occurred between the PET and the copolyester heat-seal layer. (b) Infrared spectra of exposed surfaces at section of propagated delamination, neither of these two spectra show the weak absorption band at ca. 930 cm1; this indicates that tension failure has continued through the PET layer, and not at the interface layer. (c) Schematic of the laminated card structure. Reproduced from Chalmers [11]. Copyright 2000, with permission of John Wiley & Sons.
heat-seal layer, or a barrier layer against oxygen ingress. Depending on the amount of a surface(s) exposed by the occurrence of delaminating fault or failure, then this may be examined by techniques such as ESCA or IR-ATR to determine the cause. An IR-ATR example is illustrated in Figure 4 [11,12]. The results displayed support a mechanism of an initial adhesive failure (mechanical shock induced) at the interface between the heat-seal copolyester layer and the poly(ethylene terephtahalate) (PET) layer, which is followed by a propagating (tension) failure through the PET layer.
8. CURE Degree of cure and rate of cure for thermoset and UV-cured resins and similar are both properties that can be measured and monitored readily by a number of
682
John M. Chalmers and Robert J. Meier
techniques, including IR and Raman spectroscopy for surface layers, and the extent of cure at an exposed surface by such as ESCA. Everall et al. [12,13] showed how the variation in consumption of C ¼ C groups near the air interface of a UV-cured acrylic resin coating, about 30 mm thickness, on a PET substrate could be depth profiled, with ca. 1 mm spatial resolution, using Raman microscopy. The investigation demonstrated how the degree of cure increased significantly on moving from 2 mm below the surface into the bulk, and that a bulk level of cure was reached at about 4 mm depth. However, at the surface little cure was observed, since it was presumed that oxygen (a radical scavenger) inhibited the curing reaction.
9. CLOSING REMARK As discussed in its Introduction (Section 1), this chapter has been kept deliberately short, and just a few additional/novel examples were used to amplify the range of problem-solving capabilities some of the more common molecular characterization and analysis tools may be put to use for.
REFERENCES 1 A.Garton, Infrared spectrosocpy of polymer blends, Composites and Surfaces, Hanser Publishers, Munich, 1992. 2 K. Siegbahn, C. Nordling, G. Johansson, J. Hedman, P.F. Heden, K. Hamrin, U. Gelius, T. Bergmark, L.O. Werne, R. Manne and Y. Baer, ESCA Applied to Free Molecules, North-Holland Publishing Company, Amsterdam, London, 1969. 3 P.M. Fredericks, Depth profiling of polymers by vibrational spectroscopy. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007, pp. 179–200. 4 R. Iwamoto, M. Miya, K. Ohta and S. Mima, J. Chem. Phys., 74 (1981) 4780. 5 P.R. Greene and C.D. Bain, Spectr. Eur., 16(4) (2004) 8. 6 A.P. Pijpers and R.J. Meier, XPS and adhesion, J. Electr. Spectr. Rel. Phen., 121 (2001) 299–313. 7 J.I. Kroschwitz (Ed.), Polymer: Polymer Characterization and Analysis, Wiley, NY, 1990. 8 J.C.J. Bart, Chapter 4 in Plastic Additives, Advanced Industrial Analysis, IOS Press, Amsterdam, 2006. 9 K. Artyushkova and J.E. Fulghum, J. Electr. Spectr. Rel. Phen., 149 (2005) 51–60. 10 G. Beamson, D.T. Clark, N.W. Hayes, D.S.-L. Law, V. Siracusa and A. Recca, Polymer, 37 (1996) 379. 11 J.M. Chalmers, Infrared spectroscopy in analysis of polymers and rubbers. In: R.A. Meyers (Ed.), Encyclopedia of Analytical Chemistry, Wiley, Chichester, 2000, pp. 7702–7758. 12 J.M. Chalmers and N.J. Everall, Qualitative and quantitative analysis of plastics, polymers and rubbers by vibrational spectroscopy. In: N.J. Everall, J.M. Chalmers and P.R. Griffiths (Eds.), Vibrational Spectroscopy of Polymers: Principles and Practice, Wiley, Chichester, 2007, pp. 1–65. 13 N. Everall, Chapter 4, Raman spectroscopy of synthetic polymers. In: M.J. Pelletier (Ed.), Analytical Applications of Raman Spectroscopy, Blackwell Science, Oxford, 1999, pp. 127–192.
SECTION VI: Polymer and Polymer Product Development: Support Techniques
This page intentionally left blank
CHAPT ER
17 The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis John Kendrick
Contents
1. Introduction 2. Methodologies 2.1 Quantum mechanics 2.2 Semi-empirical methods 2.3 Ab initio methods 2.4 Molecular density functional methods 2.5 Solid-state density functional methods 2.6 Molecular mechanics 2.7 Molecular dynamics and Monte Carlo methods 3. Infrared and Raman Spectroscopy 3.1 Poly(ethylene) 3.2 Photo-oxidation of poly(ethylene) and poly(propylene) 3.3 Poly(acrylonitrile) 3.4 Poly(methylmethacrylate) (PMMA) 3.5 Polymerisation of 3-phenyl-1-ureidonitrile 3.6 Poly(thiophenes) 3.7 Poly(aminoborane) 4. Photoelectron Spectroscopy and Auger Electron Spectroscopy (AES) 4.1 Metal: Polymer interactions 4.2 Poly(ethers) 4.3 Poly(pyridine) 4.4 Conjugated polymers 5. Mass Spectrometry 5.1 Poly(carbonate) 5.2 Ethoxylated polymer 5.3 Conjugated systems 5.4 Sequencing of polymers 5.5 Poly(vinyl acetate)
Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00417-0
686 687 687 688 689 690 690 691 692 693 696 697 697 698 700 701 702 703 708 709 710 711 712 713 713 714 715 717
r 2008 Elsevier B.V. All rights reserved.
685
686
John Kendrick
6. X-Ray Diffraction 6.1 Engineering polymers 6.2 Polyester copolymers 6.3 Aliphatic poly(amides) 7. Nuclear Magnetic Resonance 7.1 On the role of chain length and stiffness 7.2 Poly(thiophenes) 7.3 Poly(ethylene oxide) 7.4 Organosiloxanes 8. Electron Spin Resonance 8.1 Hydrogen abstraction 8.2 Poly(aniline) 9. Summary References
718 718 720 721 722 723 724 725 726 727 728 728 729 730
1. INTRODUCTION Analytical methods provide such a wealth of detail and information that it is often difficult to find a framework to make sense of the data. It is becoming increasingly common for modelling methods to be used alongside experiment to help interpret the data and provide a model for their understanding. This chapter does not provide a detailed discussion or explanation of the modelling methods that are available to polymer scientists, but instead attempts to outline the methods that are available without going into too much technical detail, and illustrates, through examples from the literature, what can been achieved. References will be given to more detailed technical descriptions of the techniques discussed. The emphasis is on the role that molecular modelling has in supporting analytical methods in polymer science. One of the fallacies that has been promulgated in the past is that simulation will eventually replace experiment. Those who have been involved in the application of simulation and theory know that this is far from the truth. The reality is that simulation and experiment go hand in hand. In any given area, simulation will be leading and giving ideas for experimentalists to follow up and check out. Likewise, experiments will be posing the simulators challenges to meet. Underlying both simulation and experiment is a theoretical idea or concept which, for the want of a better word, we will call a ‘model’. It is the job of the simulator and experimentalist to assess the validity of this model and the two approaches tend to come at the problem from different ends. The experimentalist tests the model against reality, whilst the simulator tests the ability of the model to predict. The role of the molecular modeller should therefore be to provide confirmation on the suitability, reliability and robustness of the model. Of course in any technical area such as this, there are some who get interested in the technicalities of the simulations and implementations of the models. This is only right and proper and drives
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
687
forward our technical capability. This chapter will attempt to draw out those areas where molecular modelling has impacted on the ‘model’ understanding. It is impossible in the modelling of polymers to avoid the size and time scale issues of polymer behaviour and many polymer properties depend on the largest length and time scales of the polymer chain. There have been several attempts to break down properties into group contributions, including: van Krevelen [1], Askadskii [2] and Bicerano [3]. Such approaches have enormous potential for the prediction of properties, but will not be considered any more in this chapter. Another area of polymer modelling that will not be considered in any depth is the mesoscale modelling area. Tools such as dissipative particle dynamics (DPD) [4] and Mesodyn [5] have allowed simulation to bridge some of the size and time scale gap that occurs between atomistic and continuum modelling. These methods are able to describe the equilibrium thermodynamics of polymer mixtures and solutions and predict the evolution of a system towards equilibrium. A survey of these approaches and their application can be found in reference [6]. This chapter will concentrate on atomistic models and their use in interpretation of various spectroscopies, including; infrared (IR), Raman, photoelectron spectroscopy, mass spectroscopy (MS), X-ray diffraction (XRD), nuclear magnetic resonance (NMR) spectroscopy and electron spin resonance (ESR) spectroscopy. Modelling techniques have in the past been limited in their application, but developments in computational power and in the availability of suitable, and useable software has meant that the tools have become available to the nonmodelling expert. The examples in this chapter have been chosen to illustrate some of the capabilities and interpretive power of the methods. Where it is possible reference will be made to some of the more ‘cutting edge’ developments that are making an impact in molecular modelling and quantum chemistry.
2. METHODOLOGIES Polymers by definition are large molecules, and it is difficult to choose the best order in which to discuss the methodologies that are used to model their behaviour. One can either use a top down approach and discuss the largest size scale methods first, or a bottom up approach and start by thinking about the smallest scale interactions first, and then begin averaging over length and time to move towards the larger size scales. In this chapter we will start at the smallest size scale and develop the description of the larger size scales later.
2.1 Quantum mechanics The solution of the time independent, non-relativistic Schro¨dinger equation has the potential to solve all our problems. Knowledge of the geometry of the molecule, allows the calculation of the wavefunction and energy of the molecule, from the deceptively simple equation: ^ ¼ EC HC
(1)
688
John Kendrick
^ represents the Hamiltonian operator for the system, describing the Here H electron–nuclear interaction, the electron kinetic energy and the electron–electron interaction. C is the N-electron wavefunction for the system and E its energy. All molecular properties can be determined in principle from the wavefunction or from the response of the wavefunction to a perturbation. The derivatives of the energy can be calculated fairly routinely and can be used to minimise the energy with respect to the geometric variables, giving good approximations to the equilibrium geometry. For molecules the method of solution is now fairly routine and there are many good descriptions in books including those by Leach [7] and Jensen [8]. Here we will simply outline the approaches and point towards the recent developments. The starting point for any calculations on the electronic structure of a molecule is the solution of Schro¨dinger equation using a quantum chemistry package such as MOPAC [9], GAMESS-UK [10], Dalton [11], Spartan [12] Orca [13] or Gaussian [14]. The only input required is an initial geometry. The program can determine the nearest geometry, which will be a (possibly local) minimum energy, together with the electronic wavefunction or electronic density, from which all manner of molecular properties can be calculated. A short description of the various algorithms used to solve the quantum mechanical molecular electronic structure problem is given below. Quantum mechanics has limited application to large molecular systems because the computational effort required to solve the equations increases rapidly with molecular size. This means that quantum mechanical calculations are usually performed on relatively small fragments of the polymer chain in isolation and it has to be demonstrated that the property of interest has converged with respect to the size of the fragment being considered. Another approach, to include the effect of the environment, is to perform the calculation in an effective dielectric continuum, or to treat a small cluster of molecules. Molecular mechanics based methods, on the other hand, because of their computational speed, are the methods of choice for larger systems and a brief outline of these methods will also be given. The future of all quantum mechanical, but in particular the ab initio and density functional theory (DFT), approaches looks bright. New algorithms are being developed that scale linearly in computational requirement with the number of atoms; the cost of computer memory is remaining very low and the approximate doubling of computational power every 18 months appears to be continuing.
2.2 Semi-empirical methods Semi-empirical methods, such as those implemented in the MOPAC [9] program, simplify the equations considerably by neglecting many terms, but then compensate for this by parameterising some of them so that the calculations reproduce experimental information on, for example, the heat of formation. Once the various approximations are made, the molecular properties to which the parameters are fitted, and the molecules used in the fitting, define a model Hamiltonian, of which the most commonly used are the AM1 and the PM3 Hamiltonians found in MOPAC. A major advantage of semi-empirical methods is
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
689
the speed of computation. Molecules of several hundred atoms can be treated using a semi-empirical method. However, the accuracy of a semi-empirical calculation depends on the groups that have been included in the fitting procedure and there is no systematic way of improving the reliability of the calculations.
2.3 Ab initio methods Ab initio calculations usually begin with a solution of the Hartree–Fock equations, which assumes the electronic wavefunction can be written as a single determinant of molecular orbitals. The orbitals are described in terms of a basis set of atomic functions and the reliability of the calculation depends on the quality of the basis set being used. Basis sets have been developed over the years to produce reliable results with a minimum of computational cost. For example, double zeta valence basis sets such as 3-21G [15] 4-31G [16] and 6-31G [17] describe each atom in the molecule with a single core 1s function and two functions for the valence s and p functions. Such basis sets are commonly used, as there appears to be a cancellation of errors, which fortuitously allows them to predict quite accurate results. The Hartree–Fock method neglects the instantaneous correlation between electrons that may be incorporated by a variety of algorithms, including configuration interaction (CI), multi configuration self-consistent field (MCSCF) and Møller Plesset 2nd order perturbation theory (MP2), 4th order perturbation theory (MP4) and a variant, MP4(SDQ), in which only single, double and quadruple substitutions are considered. Accurate calculations using such methods require large basis sets that include polarisation functions. Polarisation functions, such as d functions for the first row atoms, are available for standard basis sets and are often referred to as, for example 6-31G [18], some papers will refer to this basis set as 6-31G(d,p). The two stars indicate p functions have been included on hydrogen as well as d functions on the other elements. These correlated methods produce very reliable results for energies, geometries and vibrational frequencies. Sometimes a ‘+’ sign is used in the designation of the basis set, indicating that diffuse functions have been included, some basis sets also refer to this as an augmentation of the basis set. It is quite common to see even larger basis sets being used. A series of correlation consistent basis sets has been developed by Dunning et al. [19–25], which allows extrapolation of the total energy to the complete basis set limit in a consistent way. These basis sets form a series and are referred to by the designation cc-pVDZ, cc-pVTZ, cc-pVQZ, cc-pV5Z, etc., indicating a correlation consistent basis set of double zeta valence, triple zeta valence, etc., quality. In principle, ab initio methods can calculate an energy or geometry to any required level of accuracy. In practice the more accurate methods require large basis sets and this rapidly increases the computational cost of the calculation to a point where they are prohibitively expensive. It is easy to fall into the trap of assuming that a large basis set calculation is always better than a small one. There are two sources of systematic error in ab initio calculations. A feature that can be used to advantage, as the
690
John Kendrick
errors can cancel each other out. In any calculation there is always a lack of a complete basis set and a lack of a complete treatment of electron correlation. So it can be that, for a specific property, a particular combination of basis set and treatment of electron correlation will provide reliable predictions. The only way of determining where this is feasible is by careful calibration on smaller systems.
2.4 Molecular density functional methods DFT is a relative newcomer to the field of computational chemistry. Rather than calculating a wavefunction, density functional methods calculate the electron density directly. Whilst much of the computational machinery is similar, these techniques should not be regarded as related to Hartree–Fock or even post Hartree–Fock methods. Kohn and Sham [26] provided the theoretical foundations for the approach. Instead of generating the electron correlation through the wavefunction, correlation is introduced as an operator. The method assumes a functional form for the contribution of the electron density to the electron correlation and to the electron exchange energies. The functional may be local (local density approximation (LDA) functionals), in which case it depends only on the value of the electron density in space. More recent and more accurate functionals use a non-local potential [27] and they depend on both the values of the electron density and its derivatives (gradient corrected functionals). A widely used functional is the B3LYP gradient corrected density functional. This uses Becke’s three-parameter functional [28–31], which incorporates Becke’s exchange functional and a fraction of the exact Hartree–Fock exchange, together with the non-local correlation functional of Lee et al. [32]. Although this functional is a popular one, it is by no means the only one. The choice is large and it has become clear in recent years that some functionals are better than others at predicting particular properties and that there is no one functional that stands out as being good at predicting all properties. So the choice of functional requires care, and preliminary calculations on model systems are always to be encouraged to ensure that the reliability of the combination of basis set and density functional for the property of interest is well understood. DFT has proved to be as computationally efficient as Hartree–Fock methods whilst providing results with reliability as good as some of the post Hartree–Fock methods such as MP2. This combination of features has meant that it has become the method of choice for quantum calculations on larger molecules.
2.5 Solid-state density functional methods Based on the same underlying principles as the molecular-based quantum methods, solid-state DFT represents the bulk material using periodic boundary conditions. The imposition of these boundary conditions means that it becomes more efficient to expand the electron density in periodic functions such as plane waves, rather than atom-based functions as in the molecular case. The efficiency of the calculations is further enhanced by the use of pseudo-potentials to represent the core electrons and to make the changes in the electron density
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
691
smoother near the nucleus. In principle both crystalline and amorphous polymers can be treated quantum mechanically using 3D periodic boundary conditions. In practice calculations are limited by the available computer memory and computer power. These DFT methods have been developed extensively within the solid-state physics community and their application to chemistry is not as well developed as the molecular-based methodologies. A wide-ranging introduction to the area can be found in references [33,34].
2.6 Molecular mechanics The molecular mechanics method, often likened to a ball and spring model of the molecule, represents the total energy of a system of molecules with a set of simple analytical functions representing different interactions between bonded and non-bonded atoms, as shown schematically in Figure 1. The bonded atom interactions are usually split into bond stretching, bond bending and torsion twisting terms. The non-bonded interactions are represented by three main contributions. There is a short-range repulsion term, which prevents atoms from overlapping. This is often represented by an r12 term (where r is the internuclear separation) as in the Lennard-Jones potential, but a term with exponential dependence on internuclear distance is also often used. The two other non-bonded terms are longer range in nature. The first is the attractive van der Waals interaction, which has an r6 dependence, and is usually included with the repulsion term described above to give a single function. The other non-bonded term is the electrostatic interaction, which usually has an r1 dependence (sometimes a distance-dependent dielectric constant is used to decrease the range of interaction to r2). The electrostatic interactions are usually described by the interaction between charges centred on the atoms. Because of Torsion
Bond stretch d en
B gle
An
Non–bonded
Figure 1 Components of the energy in molecular mechanics calculations.
692
John Kendrick
the long-range nature of the electrostatic interaction in periodic systems it is necessary to use special methods, such as that due to Ewald [35], which ensures convergence of the infinite sums over the lattice. The determination of the values of atomic-centred charges is a very important requirement for the reliable prediction of non-bonded interactions. A common approach is the potentialderived charge (PDC) method [36]. In the PDC method an ab initio wavefunction is analysed to give the electrostatic potential around the van der Waals’ surface of the molecule. The method optimises the charges at atomic centres so as to fit this electrostatic potential, whilst constraining the charge to reproduce the total charge of the molecule. This procedure ensures that the long-range (dipole–dipole) interactions are reasonable, whilst ensuring that the local interactions between charge groups near the van der Waals surface of the molecules are well represented. There appears to be a cancellation of errors when using the Hartree–Fock method to calculate the charges. It is well known that larger basis sets tend to systematically predict too large a dipole moment, when compared with the experimental gas phase results. However, it is believed that this is more appropriate for molecules in the solid state where additional charge separation is likely to lead to increased stabilisation. The reliability of molecular mechanics calculations hinges entirely on the validity and range of applicability of the force field. The parameterisation of these functions (the force field) represents the chemistry of the species involved. Many force fields have been developed and the one used in any application usually depends on the molecular mechanics package being used. The force field itself can be validated against experimental and ab initio results. Because of the relative speed of molecular mechanics calculations, it is possible to consider routine calculations of a large number of atoms, certainly tens of thousands, which makes the method amenable to calculations on polymers. To remove surface effects, calculations of bulk properties are normally carried out employing 3D periodic boundaries. In this way it is possible to perform calculations on both amorphous and crystalline systems.
2.7 Molecular dynamics and Monte Carlo methods In the methods discussed above, both quantum mechanics and molecular mechanics calculate the total energy and its gradients as a function of the nuclear coordinates. Geometry optimisation using these methods finds the nearest local, minimum energy configuration, which although relevant for small molecules with only a few degrees of freedom is not useful for polymers which have very many degrees of freedom. Molecular dynamics (MD) and Monte Carlo methods both provide two useful but distinct roles. On the one hand they provide algorithms for the rigorous calculation of thermodynamic properties. On the other, they can be used as convenient computational tools to explore the conformational energy landscape of the polymer and to make sure that the simulation has escaped from the local minimum that may simply result from a poor starting geometry. MD calculations integrate Newton equations of motion forward in time, so that the dynamical behaviour of the system can be predicted. The calculations
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
693
can be performed in a number of statistical mechanical ensembles, including NVT, NVE and NPT, where N, V, E, P and T indicate ensembles in which the number of atoms, the volume, the energy, the pressure or the temperature, respectively, are constant. In principle, MD can be used to calculate all the thermodynamical properties of a system. In practice, the information that can be obtained is limited by the time scale which the simulation can access, typically up to tens of nanoseconds. It is possible that simulation is only able to sample part of the phase space available to the system and this will naturally limit the applicability of the results. The time scale issue is a central problem to the simulation of polymers, which often have several processes occurring simultaneously on different length and time scales. Amorphous polymers are usually simulated using a 3D periodic box packed with one or more polymer chains, using an algorithm that attempts to reproduce the correct statistical properties of the isolated chain. The box is then equilibrated using MD, often using the NPT ensemble, which allows the polymer density to fluctuate. Once an equilibrated sample has been generated, the NVT ensemble can be used to assimilate statistics of the dynamics of the polymer from its fluctuations. MD calculations have been used to predict polymer densities [37], cohesive energy densities [38] (and hence Hansen solubility parameters), glass transition temperatures [37] and diffusion rates in polymers [39]. Whereas MD follows the dynamical evolution of a system over time, Monte Carlo methods average over the phase space of the system. The averaging is usually done using a form of the Metropolis sampling procedure. Given a starting point, a ‘move’ is attempted. As long as it is reversible, the move can be almost any change to the system, a change in volume, a change in pressure, a swap of two halves of a polymer, a rotation around a bond. It is this freedom in choice of move which allows the method to explore the phase space of the system. After the move, the energy of the new system is calculated. If the energy has gone down the new state is accepted. If the energy has gone up, there is still a probability of it being accepted, which is determined by a Boltzmann probability, P, which is a function of the change in energy and the temperature, T. Enew Eold P ¼ exp (2) kB T The Boltzmann constant is represented by kB. It is more difficult to use Monte Carlo methods to investigate dynamic events as there is no intrinsic concept of time but an ensemble average over the generated states of the system should give the same equilibrium thermodynamic properties as the MD methods. A good review of both MD and the Monte Carlo methods can be found in the book by Frenkel and Smit [40].
3. INFRARED AND RAMAN SPECTROSCOPY Probing the vibrations of a polymer has provided a wealth of information about its chemical composition, its conformational states and its local environment
694
John Kendrick
(amorphous or crystalline). Calculations of vibrational spectra can be carried out by a variety of methods. Perhaps the commonest is the quasi-harmonic approximation, which assumes that the normal modes are essentially harmonic in nature and can therefore be determined by diagonalisation of the mass weighted force constant matrix, F. The force constant matrix, or Hessian as it is sometimes known, is the mass weighted second derivative of the energy with respect to the nuclear coordinates. 1 @2 E Fij ¼ pffiffiffiffiffiffiffiffiffiffiffiffi Mi Mj @Xi @Xj
(3)
where Xi is a cartesian atomic coordinate associated with an atom of mass Mi. The normal modes, Q, are the eigenvectors of F and the frequencies, n, are related to the eigenvalues (lk) by pffiffiffiffiffi lk vk ¼ (4) 2p FQ ¼ lQ
(5)
The second derivatives can be calculated numerically from the gradients of the energy or analytically, depending upon the methods being used and the availability of analytical formulae for the second derivative matrix elements. The energy may be calculated using quantum mechanics or molecular mechanics. Infrared intensities, Ik, can be determined for each normal mode from the square of the derivative of the dipole moment, m, with respect to that normal mode. @m 2 Ik / (6) @Qk The Raman intensities are more difficult to calculate as they involve the derivative of the polarisability along the normal mode. An alternative approach is to use the fact that an MD calculation samples the vibrational modes of the polymer for a period of time, t, from 0 to tmax and to calculate from the trajectory, the mass weighted velocity autocorrelation function. Transforming this function from the time domain into the frequency domain by a Fourier transform provides the vibrational density of states g(n). In practice this may be carried out in the following way: Z tmax qffiffiffiffiffiffi 1 _ j e2pint dt Aj ðnÞ ¼ Mj X tmax 0 (7) 2 X n Aj ðnÞAj ðnÞ gðvÞ ¼ kT j This function is a continuous analogue of the frequencies derived from the quasiharmonic approximation. Information about the intensities can be obtained by using the dipole moment autocorrelation function in place of the velocity. The advantage of using MD to build up information about the vibrational modes of the polymer is that the approach incorporates an averaging over many vibrational states of a complex molecule, which may be changing conformation
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
695
in time. The disadvantages are that it is necessary to sample the MD trajectory frequently to obtain accurate high-frequency vibrations and it is also necessary to run a long MD trajectory to obtain accurate low-frequency information. Although this approach seems ideally suited for polymers, a number of factors have meant that little attention has been paid to the method in recent years. One assessment of the method applied to polymers can be found in the study by Tilbrook and co-workers [41]. Although aimed at polymers, their study included calculations on benzene, chlorobenzenes, triazines, phenoxy triazines, diphenyl ether and diphenyl sulfide. They compared predictions of infrared intensities from the dipole autocorrelation function of MD calculations with those obtained from semi-empirical, quasi-harmonic calculations. Their conclusion was that an approach based on MD provided useful information but was often difficult to interpret. This conclusion is supported by the work of Henssge and others [42] on the infrared spectrum of poly(ethylene). A useful resource for assessing the accuracy of the various methods for calculation of vibrational spectra is provided by the National Institute of Standards and Technology (NIST) [43] in the Computational Chemistry Comparison and Benchmark Data Base (CCCBD). Most methods for calculating the normal modes and their frequencies have systemic errors in the predictions. Typically, Hartree–Fock methods predict vibrational frequencies that are too large and this can be traced back to the inability of the method to describe bond breaking correctly, resulting in bond lengths that are underestimated. This systematic deviation can be partially corrected by scaling the predicted frequencies by a factor that depends on the basis set and method for treating electron correlation. Table 1 provides a summary of a few of the scaling factors available in the database. The database should always be consulted for more up to date values. The DFT method using the BLYP functional appears to predict good frequencies independent of the basis set being used. The main effect of increasing the basis set size is to lower the uncertainty of the scaling factor. Thus the largest basis set shown, the triple zeta valence 6-311G basis set, using the B3LYP functional, has the lowest standard deviation associated with the predictions. In this respect, despite it having a relatively large deviation from unity, this method should be regarded as more reliable than the others in the table. A detailed study of scaling factors and their associated uncertainties
Table 1 Scaling factors used to improve the frequency predictions of ab initio and DFT calculations Method
6-31G
6-31G
6-311G
Hartree–Fock DFT BLYP DFT B3LYP MP2
0.90370.040 0.99270.047 0.96270.041 0.95770.046
0.90370.026 0.99270.027 0.96170.045 0.93770.027
0.90970.025 0.99670.026 0.96770.021 0.95070.025
696
John Kendrick
has been made by Irikura et al. [44], who analysed 40 combinations of theory and basis set. When attempting to aid the assignment of experimental infrared or Raman spectra using calculations it is important to bear in mind that after scaling there is still a 2% error in the predicted frequency, even for the largest basis set. This uncertainty is large enough to lead to the incorrect ordering of bands. Two steps can be undertaken to improve the confidence of the assignments. The first is to use the predicted relative intensities and the second is to make use of calculations on model compounds for which more detailed assignments may be available. Recent progress has been made in developing algorithms for the calculation of anharmonic vibrational effects through the calculation of higher order derivatives of the energy [45]. Results indicate that for the azabenzenes studied it is possible to predict fundamental frequencies with an average error of below 10 cm1 without resorting to any scaling factors, using a B3LYP density functional with medium-sized basis sets.
3.1 Poly(ethylene) In a series of papers Meier and co-workers [46–49] have applied a mixture of quantum calculations and Raman spectroscopic measurements to study some of the properties of poly(ethylene). Monofilaments of highly oriented, high molecular weight poly(ethylene) have been shown to have two bands in the carbon–carbon stretching region at 1,060 and 1,130 cm1 corresponding to the antisymmetric and symmetric stretch, respectively. Under strain some of the bands are seen to shift significantly, which is thought to arise from those chains under strain. Meier and Vansweefelt [46] tested the hypotheses used to extract information from the spectra of samples under strain by modelling the poly(ethylene) chain as n-octane. Full geometry optimisation was carried out at the Hartree–Fock, 6-31G level, first on an unstrained extended chain, and then on a chain constrained to be 10% longer. Although the calculations are qualitative in nature, the shifts predicted are almost quantitatively correct. Application of strain is seen experimentally to broaden the antisymmetric stretch most and this is nicely explained by the larger shifts in frequency that are calculated to occur for one of the transitions making up the antisymmetric stretch band. Tarazona et al. [50] and Koglin and Meier [51] investigated the dependence of the predicted Raman spectra on the conformational properties of poly(ethylene) using normal mode analysis with a Hartree–Fock 6-31G basis on oligomers up to C16. In particular they studied the effect of trans and gauche conformers on the predicted spectra. The work was able to rationalise many of the temperaturedependent features of the spectrum. In particular the temperature independence of the features around 1,300 cm1 was reflected in the insensitivity to conformational change shown by the calculations in this region. A much greater degree of conformational dependence was discovered in the 700–1,000 cm1 region, where melting is known to increase the Raman band intensity. The calculations showed a clear increase in intensity for those conformers with a higher gauche content in agreement with the experimental observations.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
697
A significant feature of this work was the demonstration that short oligomers can be representative of the vibrations in polymers, even when disorder is taken into account.
3.2 Photo-oxidation of poly(ethylene) and poly(propylene) Another example of the close interplay between calculation and experiment can be found in the work of Bertoldo and co-workers [52] on the experimental and theoretical investigation into photo-oxidation of poly(olefins). It is commonly assumed that oxidation of poly(olefins) takes place by free radical attack on the polymer (see e.g., Chapters 11 and 12), forming alkyl radicals which can react with oxygen to produce a variety of oxygenated molecules including alcohols, ketones, carbonyls and esters. Interpretation of the complex IR region between 1,700 and 1,800 cm1 is difficult, as the large number of transitions leads to broad bands. Calculations were performed with a 6-31+G basis set with the B3LYP density functional on models of a variety of potential photo-oxidation products, focusing on the localised modes associated with the carbonyl stretch and the carbon–carbon double bond rock. The calculations were used to predict the vibrational frequencies and the relative intensities of the transitions. The authors had also deconvoluted the observed experimental data in the carbonyl stretch region of the spectra from oxidised samples of poly(ethylene) and poly(propylene) finding contributions from 2 and 6 transitions, respectively. For each of these transitions they were able to confirm the assignment of the likely group involved on the basis of the calculated frequency. Rather unusually, these authors also examined environmental effects by calculating the transition in the presence of an effective dielectric medium using a polarisable continuum model (PCM) theory [53]. Including environmental effects in this way caused a reduction in the transitions associated with the carbonyl stretch by between 15 and 30 cm1 and an increase in their predicted intensities. Using the extinction coefficients for each moiety making up the observed transitions the authors then went on to calculate its concentration as a function of time. If internal ketone groups are present it is assumed that they can undergo a Norrish type II interconversion giving a terminal ketone and vinyl group, as shown in Figure 2. From calculation they were able to confirm the greater propensity for oxidation of the poly(propylene) as opposed to the poly(ethylene) chain. Also poly(ethylene) was seen to be much more likely to have unsaturated carbon–carbon double bonds rather than carbonyl groups as its oxidative products. The effect of including environmental effects in the modelling was to reduce the overall concentrations of oxidised chains, but the qualitative conclusions were the same.
3.3 Poly(acrylonitrile) One of the advantages of the simulation of infrared and Raman spectra is the ability to separate the contribution that different conformers make to the overall spectrum. Mathieu and Grand [54] used a quasi-harmonic method using ab initio
698
John Kendrick
O
H
hν OH
C•
C•
O
HC +
CH2
Figure 2 Norrish type II mechanism for photo-oxidation of polyolefins. N H N C C
C H
H
∗
C C n∗ H2 H
Figure 3 Molecular structure of acetonitrile and poly(acrylonitrile).
Hartree–Fock theory with a variety of basis sets to study their effect on the predicted Raman frequencies and intensities. Calculations of acetonitrile itself, Figure 3, showed that the Raman intensities varied little with basis set. This is rather a surprising result as the Raman intensity is related to the change in polarisability on vibration and polarisability is notoriously difficult to calculate accurately, requiring very large basis sets. Having decided on using the 6-31G basis set, Mathieu and Grand investigated the dependence of the predicted spectra on environment by performing calculations on clusters of acetonitrile. The calculations again showed little influence on the intensities of the scattering, a conclusion that needs to be verified with calculations using a larger basis set incorporating polarisation functions. Finally oligomers of poly(acrylonitrile) (PAN), Figure 3, were investigated to see if the predicted frequencies and intensities would converge. Previous work [55] on the infrared spectrum of PAN had indicated that oligomers of 5 or more units were needed. The Raman spectrum however converges even more quickly and appears almost independent of the degree of polymerisation. Their results do show, however, that the measured spectrum is very sensitive to the conformation of the polymer and only indirectly sensitive to its tacticity.
3.4 Poly(methylmethacrylate) (PMMA) PMMA can polymerise to form three different chains, depending on the tacticity of the chiral carbon in the chain. The isotactic (i-) and the syndiotactic (s-) forms are shown in Figure 4. An understanding of the influence of the various forms on the material properties of PMMA is important and variable temperature infrared and Raman
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
CH3
CH3
CH3
Isotatic
699
∗
O
O
O
n
C H2
C H2
C H2
O
O
O
O
Syndiotactic O
CH3
CH3
∗ C H2
C H2
CH3
n
C H2 O
O O
O
Figure 4 Molecular structures of isotactic and syndiotactic PMMA.
spectroscopy could be a useful tool for interrogating the conformational states of the polymers. Tretinnikov and Ohta [56] reported measurements of variable temperature Fourier transform infrared (FTIR) spectra on amorphous forms of isotactic and syndiotactic PMMA and used theoretical calculations for methylmethacrylate [57,58] to interpret the sensitivity of the bands to the conformational state. Unlike many of the other works reported here on vibrational spectroscopy, this work relied much more on the calculation of conformational energies to aid in the interpretation of the spectra rather than the calculation of the intensities or frequencies. Analysis of the temperature dependence of the C–O stretch modes at 1,050–1,300 cm1 using band fitting showed the presence of seven and six components for s- and i-PMMA, respectively. The two bands of highest frequency correspond to the C–C–O vibration which is suggested to split due to the presence of two conformational states of the ester group, as shown in Figure 5. Because of the difference in energy of these two groups, temperature changes alter the population of the two states. Ab initio calculations indicated [57,58] that the high-frequency peak is due to the trans conformation and the lower frequency peak to the cis conformation. Analysis of the relative band area gives the population of the two states as a function of temperature and hence allows
700
John Kendrick
Cis
O
O
Trans
O
O
Figure 5 Molecular structures of the cis and trans conformations in poly(methylmethacrylate).
the determination of the energy difference between the two states. Interpretation of the temperature dependence of the intensities of i-PMMA and s-PMMA provides a fascinating insight into the dynamics of the polymer. The syndiotactic polymer shows an increase in the relative intensity of the trans peak over the cis peak above a temperature of about 551C. The logarithm of the increase becomes linear above the glass transition temperature of the polymer (1251C). The isotactic polymer, however, shows a decrease in the relative intensity; the logarithm of the decrease becoming linear above 401C. The onset of the increase (decrease) in syndiotactic (isotactic) PMMA corresponds with the known b transition in these materials, confirming NMR results that show the b transition to be due to the onset of a 1801 rotation of the ester group about the OC–C bond. The fact that the population change has a different sign shows that the most stable conformer in the syndiotactic polymer is the cis conformer and raising the temperature converts some of the conformers to the trans form. However, for the isotactic polymer the stable conformation is trans and raising the temperature introduces cis conformers. The difference in absolute energies between the two states is predicted to be 1.84 and 0.46 kcal/mole for isotactic and syndiotactic polymer, respectively. Another significant contribution this work makes to the knowledge of the dynamics of PMMA is the role of the ester group in the glass transition temperature. The authors show that the ester group is not contributing to the i-PMMA glass transition temperature, whilst in s-PMMA strong intermolecular bonds appear to be forming between ester groups, resulting in an elevation of the glass transition temperature.
3.5 Polymerisation of 3-phenyl-1-ureidonitrile A semi-empirical, AM1, method was used to study low molecular weight polymers of 3-phenyl-1-ureidonitrile (PUN). Silver and co-workers [59] calculated the low-energy conformations and the infrared vibrational frequencies and intensities. PUN has potential application in the storage of high-density data on thin films. The choice of a semi-empirical method allowed the authors to investigate the structure of oligomers of PUN up to a degree of polymerisation of 8, a task that would have been prohibitive for ab initio methods. The predicted vibrational frequencies are in good agreement with experimental data. In particular both theory and experiment observe a shift to lower frequency of the C–N stretching vibration on polymerisation. The absence of absorption around
701
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
O N
N C N
H
H
Figure 6 Molecular structure of 3-phenyl-1-ureidontrile.
CF2
CF3 CF2
CF2 CF2
S
S CF2
S
S
n
CF2
CF2 CF2
CF2 CF2
CF3
Figure 7 Molecular structure of fluorinated oligothiophene.
2,200 cm1 indicates that PUN polymerises by opening of the C–N triple bond shown in Figure 6.
3.6 Poly(thiophenes) The use of organic polymers as conductors and semiconductors in the electronics industry has led to a huge research effort in poly(thiophenes), with a focus on the modification of their electronic properties so that they can behave as both hole and electron conductors. Casado and co-workers [60] have performed combined experimental and theoretical research using Raman spectroscopy on a variety of fluorinated molecules based on oligomers of thiophene, an example of one is shown in Figure 7. The calculations were performed using the quasi-harmonic approximation with quantum mechanical calculations of the force constant matrix using DFT B3LYP and a 6-31G basis set. Calculations of radical cations were treated using unrestricted DFT calculations, where a and b spin electrons are allowed to occupy different orbitals. Conjugation along the chain is expected to give rise to enhancement of the intensity of the C ¼ C/C–C stretching frequency and also a lowering in the frequency as the length of the conjugated unit increases. The study reported [60] on the effect of both chain length and substitution by a variety of electron acceptor groups. The work emphasises clearly the advantages of using a combination of theory and experiment to study these complex phenomena. The calculations provided accurate predictions of spectra for both the neutral and charged species, and were therefore able to assign the vibrational motion giving rise to each peak. It was argued that the most intense Raman transition of the neutral oligomers is likely to reflect the vibrational motion consistent with the change in geometry from neutral to cation. The geometry is of course a result of the calculations alone. Direct relationships were observed between the bond length alternation (BLA) parameters of the molecules and the Raman frequencies of the two most important bonds. This demonstrates the collective nature of the electronic and vibrational properties. Those substituents that introduced large conformational distortions of the chain brought about a reduction in the conjugation length.
702
John Kendrick
Figure 8 Comparison of experimental and predicted Raman spectrum for thiophenephosphole oligomer. Reprinted from Casado et al. [61], Figure 4, with permission from Elsevier. Copyright (2005).
Casado and co-workers [61,62] have reported similar combined theoretical and experimental studies on other similar polymers. Reference [62] reports on the measurement of the Raman spectra of 3,4-ethylenedioxy and S,S-dioxide substituted terthiophenes and their parent polymers, again supported by DFT quantum-chemical calculations. The functionalisation by a sulfone is performed with the intention of improving their photoluminescence properties. Reference [61] reports on a study of three homologues of terthiophene, where the innermost sulfur atom is replaced by phosphorous. The resulting phosphole is shown to be less delocalised than the related thiophene, indicating a disruption of the resonance along the chain. Again the combination of theory and experimental study of the Raman spectra allows an understanding of the nature of the electron delocalisation in these polymeric systems that would not be possible by experiment or calculation alone. Figure 8, reproduced from their paper, gives an indication of the accuracy which can be achieved, in this case with a quite modest DFT B3LYP/3-21G calculation.
3.7 Poly(aminoborane) Poly(aminoborane) has a relatively simple structure, as shown in Figure 9. Jacquemin and co-workers [63] performed a comprehensive set of calculations to investigate the infrared spectra, vertical excitation energies, geometries, atomic charges and dipole moments as a function of conformation. A variety of theoretical methods were employed, including Hartree–Fock, MP2 and
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
703
H H H
N B
n
H
H H
Figure 9 Molecular structure of poly(aminoborane).
MP4(SDQ), DFT (B3LYP, B98 and PBE0 functionals) and a wide variety of basis sets, all as flexible as, or more flexible than, 6-31G. Evaluation of the various methods and basis sets showed that convergence of the molecular geometries was seen for the following methods and basis sets HF/6-31G(2d), DFT/6-31G(2d) and MP2/6-311G(2d). A larger basis set is needed for the MP2 and MP4(SDQ) calculations in order for it to reach its basis set limit. For DFT calculations of the frequency, they recommend using fine integration grids to reduce numerical problems. This is to be recommended generally for any calculation of properties using DFT. Overall they find the DFT method with the PBE0 functional and the 6-31G(2d) basis set to be the most accurate and cost-effective method. Its predictions of vibrational frequencies indicate that, of the molecular conformations investigated, experimental infrared frequencies correspond either to a coiled or to a helical conformation, rather than an all trans or an alternating cis–trans form. This was also consistent with the predicted energetics of the molecules. Previous assignment of a peak at 1,380 cm1 was shown to be probably incorrect as this corresponded with an NH3 umbrella mode on a terminal nitrogen. The predicted spectra for the coiled and helical forms were very similar and would be difficult to distinguish on the basis of experimental infrared spectra. The all trans form was, however, predicted to have a sufficiently different spectrum that identification may be possible.
4. PHOTOELECTRON SPECTROSCOPY AND AUGER ELECTRON SPECTROSCOPY (AES) Photoelectron spectroscopy uses radiation to excite a molecule from an initial state (usually the ground state) to an ionised final state with an emitted electron, possessing kinetic energy, KE. The overall process can be viewed as M þ hv ! Mþ þ e ðKEÞ
(8)
The nature of the final state depends upon the energy, hn, of the exciting photons. In X-ray photoelectron spectroscopy (XPS) the exciting photons are provided by sources such as Al Ka (1,486 eV) or Mg Ka (1,253 eV) and excitation of the core electrons of the molecules is observed. In UV photoelectron spectroscopy (UPS), HeI (21.2 eV) or HeII (40.8 eV) radiation is used and excitation from the valence region of the neutral molecule is observed. XPS and UPS are surface-sensitive techniques, which are capable of providing extremely useful information on the chemical nature of a surface or interface and, in the case of the XPS, the conformational state of the molecules at the surface [64].
704
John Kendrick
Measurement of the kinetic energy (KE) of the outgoing electron gives experimental information on its binding energy (BE) in the molecule M. BE ¼ hv KE
(9)
Typically the measurements show significant broadening due to vibrational effects, overlap of bands, and bands arising from excited state initial and final states, sometimes called shake up bands. Theoretical calculation of vertical (IPv) and adiabatic ionisation potentials (IPa) can aid in the assignment of the measured binding energies. There are many calculation methods available. Deleuze and Cederbaum [65] provide a review of the various approaches and challenges to calculating ionisation processes in polymers and solids. Early in the development of the method it was recognised that a core electron binding energy shift should be affected by its atomic charge and various attempts were made to find correlations of the atomic charge with the observed binding energy [66]. Nearest neighbour and next nearest neighbour effects were reported on a variety of polymers [67], which were clearly related to the charge of the substituents. Recent work by Hoffmann and co-workers [68] on a range of 26 polymers used the semi-empirical AM1 method to calculate geometries and a Mulliken population analysis to calculate the partial charges of the atoms. They showed that there is a good linear relationship for the carbon 1s binding energies of the form BE Vm ¼ A þ Bq
(10)
where Vm is the electrostatic potential at the atom, q its charge and the parameters A and B are determined by fitting to experiment. The quality of fit was good with an R2 value of 0.98 (R is the statistical correlation coefficient) and comparable with the uncertainty in the position of the XPS peaks. One of the simplest ab initio methods for estimating the ionisation potential is the use of Koopmans’ theorem [69], which states that the orbital energy of a Hartree–Fock calculation is an approximation to its ionisation potential. Unfortunately Koopmans’ theorem neglects many important physical features of the ionisation process, including: any correlation effects in the initial and final states, changes in geometry resulting from ionisation and relaxation of the orbitals of the ionised molecule to account for the presence of the electron hole. Two natural extensions of Hartree–Fock methods were proposed to overcome some of these issues. The DSCF method [70] performs Hartree–Fock calculations on both the neutral and ionised molecules. In this way account is taken of the electronic reorganisation due to the hole. This method suffers from the draw-back that it is only suitable for the description of the lowest lying state of a given symmetry. Core-hole states, being very high in energy, are only amenable to this approach because the calculations can be forced to converge to a meta-stable solution. This makes such calculations far from trivial for the non-expert. A single excitation configuration interaction method [71] allows relaxation of the ionised state and also allows for fairly straightforward calculation of the intensities of the transitions. Based on the sudden approximation, the intensity of these transitions
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
705
are relatively easy to calculate from a configuration interaction expansion of the final state, using orbitals from the neutral molecule [72]. DFT has come to the fore in molecular calculations as providing a relatively cheap and effective method for including important correlation effects in the initial and final states. DDFT methods have been used, but by far the most popular approach is that based on Slater’s half electron transition state theory [73] and its developments. Unlike Hartree–Fock theory, DFT has no Koopmans’ theorem that relates the orbital energies to an ionisation potential, instead it has been shown that the orbital energy (ei) is related to the gradient of the total energy E(N) of an N-electron system, with respect to the occupation number of the ith orbital (ni) [74]. i ðNÞ ¼
dEðNÞ dni
(11)
We can express the difference in energy between the neutral and ionised states as an integral over this gradient over the occupation number range from 1 to 0. Z 0 Z 0 dE DEi ¼ dni ¼ i ðN 1 þ ni Þdni (12) 1 dni 1 In Slater’s half electron transition state scheme the integral is replaced by a calculation of the orbital energy occupied by half an electron. In the generalised transition state method (GTS) [75] and its related method (UGTS) using unrestricted DFT, the integral is replaced by the expression shown in Equation (14). 1 DESlater ¼ N (13) i 2 ðN Þ þ 3 N ð2=3Þ GTS (14) DEi ¼ 4 An alternative approach to calculating ionisation energies and electronic excitation, in particular for valence bands, is to use an electron propagator theory (EPT). This formalism can, in principle, provide both final-state as well as electron correlation effects. Through the concept of the Dyson orbital, fDyson , it allows an intuitive understanding of photo-ionisation. From the Dyson equation for the electron propagator the following equation may be derived [76] h X i Fþ ðEÞ fDyson ¼ EfDyson (15) P where F is the Fock operator for the reference state and ðEÞ the selfenergy operator. E provides the electron binding energy which satisfies the eigenvalue problem. The self-energy term provides an effective potential incorporating all of the relaxation correlation effects. Approximations to this self-energy term include the outer valence Green’s function (OVGF) method [77], a 2nd order, two particle-hole, Tamm-Dancoff approximation [78] (2ph-TDA), a 3rd order algebraic diagrammatic construction scheme, ADC(3) [65] and the P3 method [76].
706
John Kendrick
The OVGF function method provides a quantitative account of ionisation phenomena when the independent-particle picture of ionisation holds and as such is most applicable in the treatment of outer-valence orbitals. It provides an average absolute error for vertical ionisation energies below 20 eV of 0.25 eV for closed shell molecules. The TDA and ADC(3) methods allow for the breakdown of one particle picture of ionisation and so enable the calculation of the shake up spectra. The ADC(3) is correct up to 3rd order, is size consistent and includes correlation effects in both the initial and final states. A common method of calculating the approximate photo-ionisation crosssections is to use the Gelius intensity model [79]. Here the cross-section for a particular orbital, j, is expressed in terms of atomic contributions based on population analysis. X j smo PAl sao (16) j ¼ A Al j
where PAl is the population of electrons in orbital, j, in terms of contributions from an atomic orbital, l, on atom A and atomic cross-sections sao A. Chong and collaborators have accumulated considerable information on the accuracy of the core and valence ionisation predictions. In their early work [80,81] they used DFT calculations based on the UGTS method and the B88 exchange functional and the P86 correlation functional with a very large basis set, Dunning’s cc-pV5Z. Relativistic corrections were also estimated and the average absolute deviation of over 50 calculated core electron binding energies from experiment is 0.23 eV. However, such a large basis set severely limits the size of molecule that can be studied and in later work [82] a smaller, cc-pVTZ basis set was used. The exponents of the basis functions representing the atom, whose core electron has been ionised, were scaled according to the effective change in charge felt by the valence electrons of the atom. Further reductions in the computational demands of the method were brought about by employing the restricted diffuse ionisation (rDI) approximation for predicting the valence orbital binding energies. The rDI method spreads the change in number of electrons over all the valence orbitals of the molecule. Thus, two calculations are all that are needed to calculate the complete valence spectrum. On 20 small organic molecules this method gave an average absolute deviation from experiment of 0.2 eV for core binding energies. Application of this technique [83] to small molecule oligomers of PAN; acetonitrile, propionitrile and acrylonitrile, provided core binding energies in remarkable agreement with experiment (average absolute deviation 0.09 eV). Although the results threw light on the behaviour of PAN, it is likely that larger oligomers are needed to reliably assign the core shifts in this system. A further development of this approach was reported [84] in a series of calculations on model dimers used to represent a range of fifteen linear polymers for core electron bands and a range of six linear polymers for the valence bands. The dimer geometries were first optimised by the AM1 semi-empirical method, followed by a double zeta plus polarisation Hartree–Fock geometry optimisation. Core electron binding energies were carried out using the UGTS method and valence binding energies with a variant of the rDI algorithm. A scaled cc-pVTZ
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
707
basis set was used for the DFT calculation, which used the B88 exchange functional and the P86 correlation functional. Accounting for solid-state effects by including an estimate of the work function, the calculations gave excellent agreement with experiment. This study was supplemented by a study [85] of a further five sulfur and silicon containing molecules using the same methodology. This later study also explored the simulation of X-ray emission spectra (XES) of these molecules. Figure 10 shows a comparison of the valence band spectrum predicted for poly(ether sulfone) (PES) and measurements of the XPS and XES spectra. The methodology described above was further developed by Otsuka and co-workers [86,87] to include the interpretation of Auger electron spectroscopy (AES) in polymers [88]. They applied the method to four polymers, poly (ethylene), poly(propylene), poly(vinyl methyl ether) and poly(vinyl methyl ketone) [87]. In another paper [86] they also considered poly(cis-butadiene) and poly(styrene). The underlying methodology was the same as that described previously except that the initial state is now a singly ionised core-hole state, with a binding energy Ec and the final state is doubly ionised, arising from partial occupancy of two orbitals with ionisation potentials Ej and Ek. Ionisation from orbital k takes place in the presence of an existing electron hole in orbital j. The kinetic energy of the outgoing Auger electron can be written as EcEjEk. The intensities for the process were estimated using the one-centre intensity model of Ramaker and co-workers [89,90]. Again corrections are needed to take into account the work function of the solid and other errors, but these should be fixed for a given polymer giving rise to an overall shifting of the spectrum. Good agreement with the experimental results of Beamson and Briggs [88] were reported.
Figure 10 Theoretical and experimental valence XPS, and XES of PES (a) valence XPS with S L2,3 XES; (b) C Ka XES and (c) O Ka XES. Reprinted from Endo et al. [85], Figure 5, with permission from Elsevier. Copyright (2001).
708
John Kendrick
4.1 Metal: Polymer interactions Various calculations and experimental work has been reported on the XPS spectra of polymers at interfaces. XPS is a natural choice of method to probe the state of the polymer at the interface, but interpretation of the results is sometimes difficult. Bureau and co-workers [91] reported calculations on the interaction between platinum and poly(methacrylonitrile) (PMAN) in an attempt to elucidate the polymerisation mechanism taking place on the surface of a ˚ thick layer of polymer was observed platinum anode. Experimentally, a 20–40 A to form on the metal surface that was not classical PMAN. The calculations explored the geometry of the organic intermediates involved in the polymerisation as they absorb onto a platinum cluster and the mechanism for production of a poly(imine) (see Figure 11) network, which appears to graft itself to the surface of the metal anode. Estimates of the photoelectron spectra were then made on the basis of Koopmans’ theorem. This allowed the assignment of the large shift observed in the N 1s region to the nitrogen involved in bonding to the surface. Calculations indicated that this shift could be as large as 2.0 eV below the polymer peak. Pyromellitic dianhydride-oxydianiline (PMDA-ODA) poly(imide) films (also know as Kaptons) are used in the electronic industry and their adhesive properties onto metals have been much studied. Girardeaux and co-workers [92] have studied the interaction of PMDA-ODA, Figure 12, with titanium. Several possible sites were investigated and adsorption of monomers of PMDA-ODA as well as PMDA and ODA fragments were studied. Calculation of the XPS spectra from Koopmans’ theorem, applied to the most stable sites, reproduced the majority of the observed XPS spectra and indicated the formation of a strong Ti–aromatic ring p interaction for both the PMDA and the ODA fragments. This appeared to be more important than interactions through carbonyl groups of the PMDA unit. A large 2 eV shift in the C 1s peak was accounted for by a model
C
N
N
C
n
Figure 11 Proposed poly(imine) structure observed on platinum anodes during polymerisation of methacrylonitrile. O ∗
O
N
N
O
O
Figure 12 Molecular structure of PMDA-ODA.
O
n∗
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
709
incorporating a specific Ti–C bond. Other work has investigated the interaction of PMDA-ODA with chromium [93] and copper [94].
4.2 Poly(ethers) Beamson and co-workers [95] have reported Hartree–Fock calculations on model molecules for poly(ethyleneglycol) (PEG), poly(tetramethyleneglycol) (PTMG) and poly(trimethyleneoxide). The calculations were carried out at the Hartree– Fock 6-31G level of approximation, with intensities estimated using the methodology of Deleuze and co-workers [96] on a methyl capped oligomers of the 7/2 helix. A lot of reference is made to previous work on poly(ethylene) (PE) [97] and poly(oxymethylene) (POM) [98]. Previous work had shown that the through-space, methylenic hyperconjugation interaction in planar zigzag forms of poly(ethylene), results in a high density of states at the top of the C 2s band, giving rise to a sharp component in the XPS spectrum. Folding of the chain reduces this interaction and hence results in a broadening of the band and a change in the spectrum due to chain conformation. Poly(oxymethylene) does not naturally maintain a planar zigzag conformation, but calculations showed that the zigzag conformation would show an intense feature at the top of the C 2s and O 2s bands due to the same hyperconjugation effect. In nature POM occurs as a tight helix (9/5 or 2/1) and the hyperconjugation interactions are not present, giving rise to lower intensities at the top of the 2s band. The calculations on PEG reported the effect of conformation on the predicted spectrum and show the importance of conformation on the antibonding orbitals at the top of the 2s band. Rotation about C–C bonds appears to have little effect on the band, whilst rotation about C–O bonds relative to a planar zigzag conformation gives rise to a broader band. The conclusions drawn from the theoretical work were able to explain some of the features observed experimentally. The change from crystalline material to amorphous material brings about an increase in the number of gauche C–O links resulting in a lowering in the height of the top of the band. The influence of conformation on the valence electrons of the polymer is well known and reasonably well understood. The magnitude of the impact on the core electron states was first pointed out by Meier and Pijpers [99] on the basis of Koopmans’ theorem and DSCF calculations on poly(acrylic acid). Later measurements by Beamson and co-workers on poly(ethylene terephthalate) (PET) [100] showed that instrument developments were such that core level binding shifts of 0.1 eV were detectable and as a result it was possible to examine the nature of the crystalline and amorphous regions of semi-crystalline polymers such as PET. This conclusion is supported by calculation [101]. The work of Beamson and co-workers [95] on the other hand showed that, experimentally, the core binding energies could not be used as signatures for the onset of conformational disorder in poly(ethers). A study of the valence band photoelectron spectrum and the X-ray emission spectrum of poly(ethylene oxide) was carried out by Brena and co-workers [102] in order to understand the effect of conformation on the observed spectra. Up to 12 monomers were used in the calculations for the valence band photoelectron
710
John Kendrick
spectra predictions. A 6-31G basis set with B3LYP DFT was used, along with Koopmans’ theorem interpretation of the orbital energies. The systematic error in the predicted binding energies was corrected by shifting the predictions by a constant 2 eV. The density of states predicted by this molecular approach was compared with that predicted by a periodic DFT plane wave method and was found to be very similar. This study also uses X-ray emission spectroscopy (XES) and resonant inelastic X-ray scattering (RIXS) to study the elemental composition of the valence band. At present only Hartree–Fock methods can be used to predict RIXS scattering on large molecules. The calculations and measurement confirm the ability to use the spectroscopies to investigate the conformational state of the polymer.
4.3 Poly(pyridine) Poly(2,5-pyridyl) commonly know as poly(pyridine) has been the subject of considerable research effort as it luminesces in the blue region of the spectrum and may have uses in light emitting diodes (LEDs). Vaschetto and co-workers [103] reported a series of calculations on the molecule and its oligomers. The calculations included both the B3LYP and B3P88 density functions, Hartree–Fock calculations and a periodic solid-state DFT calculation using linear muffin tintype orbitals (LMTO). Calculations of the molecular, dimer, trimer and tetramer oligomers of pyridine were performed, in order to investigate the influence of configuration and conformation (Figure 13) on the predicted photoelectron spectra. For the dimer, the lowest energy conformation found was the trans form of the 2,2u configuration, which corresponds to a head–tail coupling. This was also the only structure predicted to be flat, although the trans conformer of the 2,3u configuration was predicted to have a shallow minimum with a low energy, flat transition state. A total of six minima were found, two for each configuration. Extrapolations were performed of various properties to infinite polymers, including the ionisation potential, the electron affinity and various excitation energies. The authors completed the work with a solid-state band calculation of C2,2′
N
C2,3′
C3,3′
Figure 13
N
N
N
N
N
Dimers of pyridine showing configurational isomerism of the cis conformers.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
711
Figure 14 The left hand side shows the band structures of poly(pyridine) calculated using a DFT-LMTO method for helical polymers. The right hand side shows its calculated density of states spectrum (solid line) and the experimental UPS spectrum (dashed line). The UPS spectrum was taken from Miyamae et al. [104]. Reproduced with permission from Vaschetto et al. [103], Figure 6. Copyright 1997 the American Chemical Society.
the density of states (DOS). A plot of the density of states as a function of energy compared well with the measured UPS spectrum as can be seen from Figure 14.
4.4 Conjugated polymers In a series of calculations on ethylene, butadiene and hexatriene, Deleuze and co-workers [105] showed that the ADC(3) method can provide a very accurate picture of the electronic processes associated with ionisation in the valence region. Poly(acetylene) has a large feature above 21 eV, which was previously assigned to shake up. The theoretical work showed conclusively that in fact even the band at around 17 eV, which had previously been assigned to a C 2s excitation could not be explained by a single particle picture but was due to satellite excitations. A range of experimental methods, XES, XPS and AES were employed to examine the electron states of an adamantine derivative (C10H12(CH3)4), pyrene
712
John Kendrick
C7H15
C7H15
C7H15
C7H15 C7H15 P14NHP
P26NHP
C7H15 P910AHP
Figure 15 Molecular structures of conjugated polymers studied by Birgerson and co-workers [108].
(C16H10) and C60 [106,107]. This was supported by a theoretical simulation of the spectra using the combinations of DFT and UGTS methods described above. The adamantine derivative was used as a model for diamond and the pyrene molecule a model for graphite. The work showed the effectiveness of the calculation methods for these quite large systems. The combination of valence XPS and C (1s) XES enabled the division of the valence electronic distribution into individual contributions for p and s bonding orbitals of the relevant allotrope. One of the advantages of the theoretical approach is its ability to look at the different components comprising the overall signal being measured. In interpreting the diamond like AES spectrum it was seen that the sharp feature in the spectrum is probably due to excitation for pure s orbitals, rather than the mixed s and p orbital excitation in the other systems. Birgerson and co-workers [108] reported an experimental and theoretical study of the chemical and electronic structure of three, alternating copolymers, shown in Figure 15. The background to the study was a desire to control the degree of conjugation by altering the steric effects along the polymer chain. The introduction of a C7 chain onto the phenylene rings was shown by semi-empirical AM1 calculations to bring about large torsion angles between the phenylene and the large arylene groups, which would localise the electron distribution. Interpretation of the photoelectron spectra was performed using an effective Hamiltonian calculation [109] of the valence density of states. Such a procedure is similar to a Koopmans’ interpretation of the band structure. The results showed good agreement with experiment and indicated that the electrons were localised. This was confirmed by calculation of the optical absorption spectra verifying the existence of large optical band gaps, consistent with the large torsion angles.
5. MASS SPECTROMETRY Mass spectroscopy is one of the few analytical methods that matches the theoretical chemists desire to observe molecules isolated, in vacuum. As such, calculations of reactions pathways, transition state and co-ordination are directly relevant and appropriate to measurements made using mass spectrometry.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
713
5.1 Poly(carbonate) Katajisto and co-workers [110] studied the degradation pathways for poly(bis phenol A carbonate) using ab initio Hartree–Fock and DFT (B3LYP). The poly(carbonate) chain was modelled by a dimer unit, Figure 16. Calculations were performed of the reaction enthalpies and Gibbs free energies for the reaction pathways that had been proposed as a result of mass spectroscopic investigation [111–115]. Estimates of the entropic and zero point energy corrections to the energetics of the reaction pathway were taken from quasi-harmonic analysis of the vibrational frequencies. Possible reactions examined included: the elimination of HCl, water substitution, elimination of CO2, dehydrogenation and C–H transfer. The elimination, or intermolecular exchange reaction, which produces a ring structure, was shown to be exothermic at higher temperatures in agreement with the observation of ring degradation products at high temperatures. CO2 elimination and the substitution with water were the most exothermic degradation reactions and this confirmed the observation of CO2 evolved during degradation. Isomerisation reactions were also investigated and assessed for the possible reaction pathway exothermicity. The calculations did not try and assess the transition states or barriers along the reaction pathways.
5.2 Ethoxylated polymer Thin polymer films created by forming a saturated solution of cationising agent, either AgNO3 or NaCl and the polymer Surfynol 465 (see Figure 17) were investigated using time of flight secondary ion mass spectroscopy [116].
O
O HO
Cl
O
O
O
Figure 16 Molecular structure of a dimer of poly(bis phenol A carbonate) used in a study of degradation pathways [110].
O
O
O x
O
Figure 17 Molecular structure of Surfynol surfactants.
H
H y
714
John Kendrick
The molecular weight distributions of the differently cationised polymers showed different number and weight averaged molecular weights. Since the role of the cationising agent is simply part of the mass spectra measurement, it is important to understand the role it might play in determining the molecular weight. Mixed molecular mechanics using the COMPASS force field and DFT calculations using the Perdew Wang density functional and a double zeta plus polarisation numerical basis set, were performed on the cation and the polymer, to understand better the nature of the interaction between them [116]. The authors concluded that the bond between the ether group and the cation was strongest for the silver cation, possibly resulting from the d-orbitals available in silver, or its greater polarisability. As a result silver binds better to the shorter chains than does sodium, this conclusion also reflects the smaller size of sodium and hence the greater strain of the rigid acetylene group. Experimentally it was observed that sodium cationised polymers showed a significantly higher average molecular weight than silver cationised polymers, in agreement with the above argument.
5.3 Conjugated systems Bushnell and co-workers [117] employed extensive molecular modelling to understand the nature of cis and trans isomerism in tetrahedral p-phenylene vinylene oligomers, and to aid the interpretation of time of flight mass spectrometry and ion mobility studies. Molecules such as T4R, shown in Figure 18, with four equivalent arms can be used to control the crystallinity in thin films. The authors reported the observation of a species in the mass spectrum resulting from the loss of an arm from the central carbon. This species will be referred to as P4R. Measurements of velocity in a drift cell, of ions under the influence of a weak applied electric field, can be related to the cross-sectional area of the species. The authors used the Amber 1999 force field, with charges determined from electrostatic potential calculations using B3LYP/6-31G calculations. For a given isomer, simulated annealing was carried out on a variety of initial structures and the five lowest energy structures used to calculate an average cross-section. These cross-sectional areas were then used to calculate an arrival time distribution (ATD), which could be compared with experiment. The number of cis–trans isomers for T4R+, which contains 12 vinyl linkages comes to 4,096, even when symmetry is accounted for there are still 330 unique isomers. To make the tBu
A
tBu
A A
Figure 18 Representation of T4R, where A represents other copies of the p-phenylene arm shown.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
715
interpretation of the experimental data more manageable the authors made the following assumptions: that the probability of a given linkage being cis or trans is independent of the conformation of the other linkages and that the probability only depends on the position along the arm. Thus for T4R there are only three probabilities, which can be determined by fitting the experimental data. Figure 19 shows the impressive results from this work, indicating the validity of the modelling and the effectiveness of a combined modelling and experimental approach. Ehlers and co-workers [118] used modelling to ask if cationisation of polymers as non-polar as poly(olefins) was feasible. Previous work using ab initio Hartree–Fock calculations had estimated that for poly(ethylene glycol) a minimum binding energy of 85 kcal/mole was needed for the complex to survive collision induced dissociation during ion extraction [119]. Their calculation, using DFT B3LYP with a 6-31G basis set, showed that the strength of interaction of a straight, aliphatic, carbon chain increases with the size of the chain. The range of interaction strengths varied from 7.8 kcal/mole for Na+–CH4 to 52.0 kcal/mole for Co+–C20H42. This indicates that even for the largest chains and the most strongly binding ions, it is unlikely that they will be seen in matrixassisted laser desorption ionisation time of flight (MALDI-ToF) mass spectra. A proviso is added at the end of the paper, which points to the potential of complexes of poly(ethers) with potassium ions with a threshold of around 64 kcal/mole. If this threshold holds then M+ complexes with poly(olefins) may become observable.
5.4 Sequencing of polymers In a combined MALDI-ToF MS, ion mobility experiment and molecular modelling study, Baker and co-workers [120] studied the sequencing in copolymers of glycidyl methacrylate and butyl methacrylate, Figure 20, with different termination groups. The Amber force field was used with simulated annealing MD on the different configurational isomers of 3-, 4- and 5-mers of the copolymers interacting with a sodium cation. The cross-sectional area of each molecule was then calculated using the appropriate atomic collision radius for collision with helium. The cross-sectional area can be related to the time it takes for the ion to drift across a helium-containing chamber under an electric field. The results of calculations on all the sequences that can be observed for the oligomers considered showed some very interesting trends. For all oligomers the ester group was bound strongly to the sodium cation. Those oligomers with glycidyl groups showed conformations that also allowed the glycidyl group to contribute to the stabilisation of the cation, resulting in a very spherical molecule, with a small cross-section. Those oligomers with a butyl group were more extended with a larger cross-section. Based on the calculated cross-sections the authors were able to assign a particular glycidyl/butyl composition to each conformation observed in the ion mobility experiment.
716
John Kendrick
300
Intensity
250 200
T4R+
150 100 50 0
a)
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.2
3.4
time (ms) 120 100
Intensity
80 T4R-Na+
60 40 20 0
b)
1.8
2.0
2.2
2.4
2.6
2.8
3.0
time (ms) 5000
Intensity
4000 P4R+
3000 2000 1000 0
c)
1.4
1.6
1.8
2.0
2.2
2.4
time (ms)
Figure 19 A comparison of the experimental and calculated arrival time distributions for T4R+, T4R-Na+ and P4R+ poly(olefins). Reproduced with permission from Bushnell et al. [117], Figure 6. Copyright (2004) American Chemical Society.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
N
b)
a) O
H
n
O
R
n
O
O
R
O
O
OR R=
717
OR O
R= Butyl
Glycidyl
Figure 20 Molecular structure of glycidyl and butyl methacrylate co-polymers with (a) H- and (b) vaso termination.
CH3 H3C C CH3
H C C H2 O
n
H
H3C C O
Figure 21 Molecular structure for poly(vinyl acetate).
5.5 Poly(vinyl acetate) Gigue`re and Mayer [121] reported on the dissociation of gas-phase poly(vinyl acetate) (PVAc), see Figure 21, ionised by Li+ investigated by electrosprayionisation (ESI) mass and collision induced dissociation (CID) mass spectrometry. The ions lose acetic acid molecules from the polymer side chain, and ultimately lithium acetate, to form a polyene with a positive charge on the carbon backbone. CID mass spectra were obtained at different centre-of-mass collision energies to study the sequential appearance of the fragment ions. Molecular mechanics/molecular dynamics (MM/MD), semi-empirical, Hartree–Fock and density functional calculations were employed to model the lowest energy pathways for the dissociation processes. A model 5-mer of PVAc was selected. Its interaction and those of its experimentally observed fragments with a lithium cation were studied using MD and simulated annealing to sample the conformation space of the molecules. Low-energy minimum energy conformations were selected for further study using semi-empirical and ab initio DFT calculations, with geometry optimisation using the 3-21G basis set and single point energy calculations using the 6-31+G(d) basis set. Corrections were made for the zero point energy of the molecules through the quasi-harmonic approximation. Consideration of the acetic acid loss at each of the five positions along the chain indicated that the lowest energy pathway for initiation of degradation takes place at the hydrogen end. The sequential loss of further acetic acid molecules should then occur from neighbouring sites as the conjugated double bonds will stabilise the product. The calculations indicated that the lithium ion remains with the polymer until the last acetate group is removed and a polyene remains. Calculations were also able to show that the transition state for the 1,5 hydrogen rearrangement for the formation of the unsaturated bond
718
John Kendrick
and acetic acid has a barrier to reaction of 232 kJ/mole for the trimer with DFT using the 6-31+G(d) basis set, in line with the experimental evidence from pyrolysis experiments.
6. X-RAY DIFFRACTION From the earliest days, molecular modelling has been used as a tool to help understand powder and fibre X-ray diffraction of semi-crystalline polymers. The calculation is relatively straightforward in that once a crystal unit cell for the polymer is proposed the X-ray scattering intensities can be predicted for the appropriate disorder found in the polymer (either powder or fibre). The procedure does not require significant computational power, as the unit cells are usually relatively small and molecular mechanics can be used to predict the atomic positions and the unit cell dimensions. The fibre pattern can of course change as a function of temperature, the Brill transition [122] in aliphatic nylons being a well-characterised example of this. To investigate temperature-dependent effects it is necessary to perform MD calculation. Care must be taken in the MD calculations to ensure that artefacts due to the choice of MD cell size do not dominate the results. It is not sufficient to take a single unit cell and perform an MD calculation as the 3D periodic boundary conditions may force the atomic motion to be correlated. The MD cell must be large enough so that atoms in the cell do not feel the influence of the periodic images of themselves.
6.1 Engineering polymers Aromatic polymers such as poly(ether ketone) (PEK), poly(ether ether ketone) (PEEK) have attracted a lot of interest due to their high-performance properties, including their stability and strength and they have been the subject of a considerable number of investigations [123–125]. Colquhoun and co-workers [126] investigated the crystalline form of thioether analogues of these polymers, which following their terminology will be called PTK and PTTK. The molecular structures of these polymers are illustrated in Figure 22. PEEK and PEK are known to crystallise in the orthorhombic space group Pbcn with two chains per unit cell. Attempts to reproduce the powder diffraction patterns observed for PTTK and PTK using the Pbcn space group failed, with large deviations between the predicted and measured scattering intensities. Calculations of the crystal packing were performed using the universal force field within the Cerius2 molecular modelling environment. Despite the similarities in molecular structure the thioethers were shown by Colquhoun and co-workers to crystallise in a completely different space group, the body-centred monoclinic space group I2/a. After geometry optimisation of the unit cell in this space group and recognition of the possible disorder that can arise along the chain in terms of the sequencing of the carbonyl and thioether groups, a comparison of the predicted and measured powder diffraction for PTTK is shown in Figure 23.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
O ∗
PEEK n
∗
∗
O
S
∗
O
PTTK n
∗
∗
S
PTK n
∗
S O
Figure 22
n
O O
∗
PEK
719
O
Molecular structures of PEEK, PEK, PTTK and PTK.
Figure 23 Comparison of the predicted () and experimental (+) X-ray scattering intensities for PTTK. The figure is taken with permission from Colquhoun et al. [126], Figure 7, with permission from Elsevier. Copyright (2006).
720
John Kendrick
6.2 Polyester copolymers Wendling and co-workers [127] reported on an extensive experimental and modelling investigation of poly(ethylene-4,4u-biphenyl dicarboxylate) (PEBB) and the related random copolymers poly(ethylene-4,4u-biphenyldicarboxylate-co2,6-naphthalene dicarboxylate) (PEBB/EN). A variety of experimental methods, including differential scanning calorimetry (DSC), X-ray diffraction and NMR were used to investigate the incorporation of ethylenenaphthalate (EN) moieties into the crystal structure of PEBB. The molecular structures of PEBB and PEN monomer units are shown in Figure 24. Calculations of the triclinic unit cell of PEBB based on previous experimental X-ray diffraction work using the PCFF91 force field indicated that the structure was unstable. Instead the authors proposed a monoclinic unit cell with two chains per cell, which they showed to be stable and capable of producing a similar X-ray scattering pattern to the original unit cell. Experimental X-ray powder diffraction pattern of copolymers of PEBB/EN in the composition range 0/100–30/70 were measured and showed little change in the peak positions with composition. If this were due to only crystalline PEBB forming the lattice, then there should be a significant decrease in intensity as the EN is incorporated. However, this was not the case. Similarly, if the EN is incorporated in the PEBB lattice then systematic changes to the lattice parameters might be expected. An unusual aspect of this work was the use of the thermodynamic integration method to estimate the Gibbs free energy of inclusion of a co-monomer into different lattice environments. In a further step a large unit cell consisting of 24 oligomers (six EBB monomer units for each oligomer) was constructed. For each oligomer, an EBB unit was selected at random and replaced with an EN group until the required composition for the copolymer was met. Thus each oligomer had an identical composition and length. All oligomers were then allowed to shift along their long axis to optimise the EBB–EBB and EN–EN interactions, based on the free energy values determined by thermodynamic integration. This resulted in segregation of the unit cell into EBB-rich and EN-rich domains. O PEN
O
O O O O
PEBB
O O
Figure 24 Molecular structure of PEN and PEBB monomer units.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
721
X-ray scattering intensities calculated from these models showed little variation as a function of concentration of EN, indicating that X-ray scattering will not be able to distinguish between PEBB crystalline domains with EN excluded from the domains and the situation where uniform inclusion in the crystalline domains takes place. The work shows clearly that no single analytical or computational method will uncover the whole, complex, behaviour of these semi-crystalline materials. NMR showed that the copolymers studied were random copolymers. 13C spin relaxation experiments showed that both EN and EBB monomers exist in two environments, a rigid phase and a mobile phase. Small angle X-ray scattering showed that the crystallinity increased with increasing EN co-monomer. DSC measurements gave an estimate of 3.6 kJ/mole for the crystal defect inclusion free energy. Finally, wide angle X-ray scattering and modelling of phase separated semi-crystalline material were consistent with a model where at 50% EN co-monomer, the EN was being excluded from the crystalline, PEBB, phase and above 50%, the EN was being incorporated into the crystalline lattice as a defect.
6.3 Aliphatic poly(amides) Many aliphatic poly(amides), more commonly known as nylons, exhibit an unusual phase transition below their melting point. First noted by Brill [122], the phenomenon has been studied extensively [128–131]. It is observed for instance in nylon (6,6) at a temperature of about 2101C, when the stable low-temperature triclinic a phase of the crystalline polymer changes to a pseudo-hexagonal phase. Tashiro and Yoshioka [132] used NPT MD using the COMPASS force field to investigate the Brill transition in crystalline nylon (10,10), see Figure 25. Figure 26 summarises the conclusions of their work. It shows a comparison of the MD simulation with a variety of experimental techniques, including DSC, X-ray diffraction and infrared spectroscopy. The DSC results indicate the onset of a phase transition at about 1401C. At 2001C the material is seen to melt. During the phase transition (labelled region II in the diagram) the 100 and 010/110 reflections observed by X-ray diffraction begin to merge as the temperature is increased. At the same time infrared measurement of the CH2 all trans sequence shows a decrease in intensity, whilst the gauche bands increase in intensity. Finally, the amide A band (associated with the N–H stretch) is seen to increase in frequency, indicating a weaker hydrogen bond as the temperature is increased. The analysis of the MD calculations, shown in Figure 26b, shows remarkable agreement with many of the experimental features. The effective unit cell dimensions (a and b) of a single chain is shown at the top of the figure. The c-axis O
O C H2
n
N H
H2 C m
N H
Figure 25 Molecular structure of a monomer unit of nylon (n+2,m).
722
John Kendrick
Figure 26 Comparison of temperature dependence of experimental data (a) and calculated results from MD (b). The figure is reproduced from Tashiro and Yoshioka [132], Figure 11. Reproduced with permission from Elsevier. Copyright (2004).
lies along the polymer chain direction and the a-axis indicates the direction of the hydrogen bonding. As can be seen the a-axis is quite insensitive to temperature, showing that the hydrogen bonds are remaining intact. The b-axis length grows rapidly above 420 K (which is assumed to be the onset of the Brill transition) until it becomes equal to the a-axis length at about 500 K. At the same time the MD shows a decrease in the population of CH2–CH2 trans conformations on increasing temperature, with a concomitant increase in gauche conformations, especially for C–C bonds next to the carbonyl of the amide group. The average N–O distance of the hydrogen bonded atoms is shown at the bottom of the figure. This shows a small rise in region I and a much steeper increase in the Brill transition region.
7. NUCLEAR MAGNETIC RESONANCE The application of NMR to the understanding of polymer properties has had a long history. The technique has allowed a powerful insight into the nature of the polymer chain and the nature of the dynamics of the polymer [133]. Case [134] reviewed the impact that quantum mechanics has had in interpreting NMR for biological macromolecules. Here we consider through some examples the impact
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
723
that modelling and experiment have made on organic polymeric materials. Molecular modelling has found two major, but distinct, roles to play in the interpretation of the NMR spectra. The first is the prediction of chemical shifts due to the chemical environment of a nuclear spin and the second is in simulation of the MD of the system. In the first, quantum mechanics can be used to calculate the NMR coupling constant between two nuclear spins in the molecular environment or the NMR shielding constant. Jensen [8] in Chapter 10 of the reference provides a comprehensive introduction to the methods for calculating these molecular properties. The NMR coupling constant, KAB, is related to the second derivative of the energy with respect to the internal magnetic moments, m, arising from the nuclear spin of the two atoms, A and B. KAB ¼
@2 E @mA @mB
(17)
The shielding constant, sA, is related to a mixed second derivative of the energy with respect to an internal magnetic nuclear moment due to spin, and external magnetic field, Bext. sA ¼
@2 E @mA @Bext
(18)
Calculation of properties due to a magnetic field is always more complicated than those due to electric field or geometry. This is because, in the case of an approximate wavefunction, the property is dependent on the origin of the co-ordinate system. Several approaches have been adopted to minimise this gauge problem, including: individual gauge for localised orbitals (IGLO), localised orbitals/local origin and gauge invariant atomic orbitals (GIAO). Packages such as Dalton [11] and Gaussian [14] are able to treat the gauge problem using a variety of methods. An issue of concern in such calculations on model systems is that often no account is taken of the environment. Sebastiani and Rothlisberger have recently suggested [135] a hybrid quantum mechanics (DFT) and molecular mechanics method that overcomes this problem.
7.1 On the role of chain length and stiffness A fascinating insight into the impact that modelling can make in polymer science is provided in an article by Mu¨ller-Plathe and co-workers [136]. They summarise work in two areas of experimental study, the first involves positron annihilation studies as a technique for the measurement of free volume in polymers, and the second is the use of MD as a tool for aiding the interpretation of NMR data. In the first example they show how the previous assumptions about spherical cavities representing free volume must be questioned. Indeed, they show that the assumptions of a spherical cavity lead to a systematic underestimate of the volume for a given lifetime, and that it is unable to account for the distribution of lifetimes observed for a given volume of cavity. The NMR example is a wonderful illustration of the impact of a simple model with the correct physics.
724
John Kendrick
Starting with a crude model of a polymer melt, consisting of anharmonic springs connecting repulsive beads, with a bending potential to represent the polymer stiffness, the authors show how the time correlation function, C(t), should be expected to behave as a function of the polymer stiffness. CðtÞ ¼ P2 ½cos yðtÞP2 ½cos yð0Þ (19) where y(t) is the angle between a C–H bond and the external magnetic field at some time, t, and P2 is the 2nd order Legendre polynomial. The model shows qualitative agreement with the trends observed in solidstate NMR experiments. In particular it shows two processes at work; a short, fast time scale process and a longer time scale process that becomes more prominent as the chain stiffness increases. They then go on to show that both the chain stiffness and the chain length have an effect on the local dynamics. A study of the re-orientation of the nearest neighbour bonds indicates that increase in chain stiffness and/or chain length results in a slowing down of relaxation processes. A subsequent publication [137] concentrates on the specifics of poly(isoprene) melts and shows that the concept of the Kuhn segment (see Chapter 4), which introduces a single unifying length unit into polymer physics, is not sufficient, as the influence of chain stiffness persists on length scales longer than had been expected. These are novel results for polymer behaviour.
7.2 Poly(thiophenes) NMR probes many types of relaxation processes including conformational interchange. In a joint dynamic NMR and quantum mechanical study of oligothiophenes and oligo(thienyl)furans, Diaz-Quijada and co-workers [138] showed that, contrary to previous thinking, interconversion between cis and trans forms appears to take place at a fast rate, even at temperatures as low as 140 K, indicating that there is a low barrier to interconversion. Hartree–Fock and MP2, 6-31G, quantum mechanical calculations predict that the lowest energy conformations are not coplanar, but twisted slightly due to steric interactions. The trans conformer appears to be more stable than the cis form by about 0.7 kcal/mole and barrier to interconversion is low, about 1.0 kcal/mole. Introduction of additional steric interaction by the substitution of methyl at the 4-position results in a more twisted minimum energy conformation for both cis and trans forms, but the barriers to interconversion and the energy differences between the two conformations is lower. Calculations of higher oligomers showed that the barrier heights and relative energies were unaffected by chain length. Based on the calculations the authors parameterised the MM2 force field to reproduce the barriers, relative energies and geometries of the oligomers and then went on to use the MD [139] to interpret some nuclear Overhauser effect (NOE) measurements. For instance, measurement of the NOE build up between H1 and H2 in Figure 27 provides a measurement of the average distance between H1 and H2. Using an MD calculation on a single molecule for 1,000 ps the mean interproton separation for selected pairs of protons was calculated from an average of
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
S
S H2 H2
Figure 27
725
H1
Molecular structure of thiophene used in the NMR NOE study [139].
1/r6. These parameters were then used in a theoretical calculation of the NOE build-up curve. The excellent agreement between theory and experiment for the build-up curves confirmed the barriers and energetics of the conformations used to parameterise the force field.
7.3 Poly(ethylene oxide) The bulk of this chapter has been discussing the way that modelling impacts the interpretation of analytical measurement, but it is easy to forget this should be a two-way process. Without measurement modellers would have nothing on which to base their confidence for the predictions. Borodin, Smith and co-worker in a series of articles set about the development of a molecular mechanics force field based on quantum mechanics calculations of polymer fragments of poly(ethylene oxide) (PEO) [140,141]. One of the key distinguishing features of their force fields is their ability to describe polarisation in a rigorous manner, either as two-body or many-body contribution to the energy. This allows the force fields to describe the interaction of the polymer with salts such as LiBF4, which is used with PEO in polymer electrolytes. The force fields were derived from ab initio calculations but were tested against experimental data such as quasielastic neutron scattering, 13C spin lattice NMR measurements, dielectric spectroscopy and viscosity. Concentrating on the spin lattice relaxation time, T1, which reflects the rate of decay of the autocorrelation function of a unit vector u(t), pointing along a particular C–H bond at time t, can be expressed; 1 ¼ K½ JðoH oC Þ þ 3JðoC Þ þ 6JðoH þ oH Þ nT 1
(20)
where K is a constant, n the number of attached protons and oH and oC the angular frequencies of the carbon and hydrogen nuclei, respectively. The spectral density, J(o), can be expressed in terms of the 2nd order Legendre polynomial, P(t) of the autocorrelation function of u(t); Z 1 JðoÞ ¼ PðtÞ expðiotÞdt (21) 2
726
John Kendrick
1 3 ½uð0Þ uðtÞ2 1 (22) 2 The autocorrelation function was calculated from monodisperse and polydis˚ . NPT perse oligomers packed into a simulation box of between 23.5 and 34 A dynamics were performed to equilibrate the system and NVT production runs were performed for up to 45 ns. Density predictions for PEO were within 1.5% of the experimental value and even the heat of vaporisation for dimethyl ether was predicted to be within 3.3% of experiment, a remarkable achievement for a force field that was not parameterised with the heat of vaporisation. The force field was tested against many other properties including the T1 spin relaxation time measurements as a function of temperature. After fitting the decay of P(t) to a suitable function, T1 is calculated with an uncertainty of between 10% and 15%. Comparison with experiment for the interior carbon atoms showed good agreement with theory for the 500 molecular weight polymer, but systematically underestimated the relaxation time for the 2,000 molecular weight polymer by about 30%. Having established the validity of the force field for such a wide range of properties the authors go on to extend and apply the force field to electrolyte systems [141]. In particular the diffusion of Li+ in the polymer medium is treated, which is one of the key properties for understanding ionic conduction in the material. Another group [142,143] studied the solid-state NMR of the polyelectrolyte systems poly(ethylene oxide)/LiCF3SO3 and poly(2-ethyl-2-oxazoline)/ AgCF3SO3 using a combined experimental and modelling approach. Quantumchemical, DFT calculations of the 13C and 1H NMR chemical shifts showed an increase in the shielding of PEO carbons and a decrease in the shielding of PEO protons in the complex with LiCF3SO3, as compared with PEO alone. The calculations of the chemical shifts were performed using DFT, B3LYP calculations with a 6-311+G(2d,p) basis set, after geometry optimisation with a 6-31G(d) basis set. The gauge issue was treated using the GIAO method. The model system, CH3O(CH2CH2O)2CH3 with LiCF3SO3, showed very similar shifts to those seen experimentally indicating that the model geometry might be applicable in the polymer. This also supported the observation that the observed chemical shifts change little between the crystalline and amorphous regions of the polymer indicating that the model is an appropriate one for local order in both regions. PðtÞ ¼
7.4 Organosiloxanes Casserly and Gleeson [144] reported density functional calculations using B3LYP/6-311++G(d,p) calculations of the 29Si NMR chemical shifts of a variety of organosiloxanes. For compounds with known shifts, they showed an average error of 3.4 ppm in their predictions. They went on to apply the method to molecular structures thought to exist in organosilicate thin films deposited using hot-filament chemical vapour deposition, for which no NMR spectrum had been measured. One of the common moieties observed is the building
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
O
CH3 O Si O
Si
Si O
727
O Si
CH3
Si O
O Si
Si O
Figure 28 Molecular structures of organosilicate moieties.
block –O–Si(CH3)2—O– shown in Figure 28. This group can form ring structures, including dimers and trimers. The dimer and trimer have a strain energy associated with them, as the natural O–Si–O angle is quite large at around 1601. The strain manifests itself in quite large shifts in the 29Si NMR spectrum. This was confirmed by the calculations, but one surprise was the shift of approximately 15 ppm predicted for siloxane rings bridged by a Si–Si bond. Close examination of the NMR spectrum of films produced by vapour deposition, especially at 1,1501C, showed a clear shoulder at exactly that position indicating the presence of these species in the film. The authors’ opinion was that this had not been previously reported.
8. ELECTRON SPIN RESONANCE Electron spin resonance (ESR), or electron paramagnetic resonance (EPR) as it is sometimes known, shares many similarities with its cousin, NMR. The origin of the phenomenon is the spin of the electron (rather than the nuclear spin) coupling with the nuclear spins of the atoms in the polymer, but much of the physics of their interactions are similar. The usual spin Hamiltonian, which is used to determine the energies of the interactions, can be written as _
H spin ¼ gmB BSz þ aI z Sz
(23)
where for simplicity only the z components of the electron spin, Sz, and the nuclear magnetic moment Iz are shown. B is the local magnetic field, g the electron g-factor, mB is the Bohr magneton and a the hyperfine coupling constant. Several quantum chemistry codes including Gaussian [14], Orca [13] and Spartan [12] are capable of calculating both the g-factor and the hyperfine coupling constants (hfccs), which arises due to the interaction of the magnetic moment of and electron with the magnetic moment of a nucleus. But the most common application of molecular quantum chemistry codes in the interpretation of ESR spectra is the calculation of the relative stabilities of radicals, from straightforward geometry optimisation and determination of their zero point energy levels. Calculations of ESR g-factors and hfccs have to treat systems with unpaired electrons, and most calculations reported use an unrestricted spin formalism, such that orbitals with b spin electrons are allowed to vary independently from those with a spin electrons. There is an important issue
728
John Kendrick
concerning DFT calculations with respect to the prediction of ESR hfccs. It has been established that, while the B3LYP functional is effective at predicting thermochemical properties, it tends to favour delocalised electrons resulting in incorrect predictions of geometries for certain classes of radical [145]. The BH&HLYP functional, which takes into account a greater proportion of the Hartree–Fock exchange has been shown to be more reliable in this respect [145]. A review of the application of ESR to the study of free radical polymerisation is given by Yamada and co-workers [146]. A survey of the application ESR spectroscopy spin label/probe methods in heterogeneous polymer systems is provided by Veksli and co-workers [147]. Spin probe methods allow the study of the MD of the polymer, its free volume, phase separation and phase morphology.
8.1 Hydrogen abstraction EPR spectra are reported on a series of low molecular weight alkanes, both linear and branched and some alkenes by Camara and co-workers [148]. The study examines the likely sites of attack of free-radicals such as the tert-butoxyl radical on model compounds such as eicosane (C20H42), tetracontane (C40H82) 2,4-dimethylpentane and 2,4,6-trimethylheptane, squalane (C30H62) and 2,6,10,14-tetramethylpentadecane, which are representative of poly(ethylene), poly(propylene) and their copolymers. 4-Octene, 5-decene, 1-octadecene and 9-octadecene were also studied as models for the presence of unsaturation in commercial polymers. Calculations of the C–H bond dissociation energy were performed using a 6-31G(d) basis set with the B3LYP density functional. The experiments indicated that, for linear polymers, hydrogen abstraction preferentially forms secondary carbon radicals, which is consistent with the calculated bond dissociation energies. However, for branched polymers, the EPR spectra indicated the presence of both tertiary and primary carbon radicals and little hydrogen abstraction secondary sites. This was not consistent with the calculated bond dissociation energies, so further calculations were performed to explore a pathway for hydrogen abstraction by a tert-butoxyl radical. The calculations of the internal energy barriers to the reactions followed the same order as that predicted by the bond dissociation calculations. It was only when the authors considered the change in free energies of the molecules at the transition state that a qualitative explanation appeared for the lack of secondary radicals. Free energies were calculated within the quasi-harmonic approximation, assuming ideal contributions to the entropy from rotation, translation and vibrations. This resulted in a larger lowering of the free energy barriers to dissociation for the primary and tertiary radicals.
8.2 Poly(aniline) Because of its sensitivity to electron spin density, EPR is an ideal tool to answer questions concerning the degree of delocalisation in conducting polymers, such as poly(aniline). EPR spectra of radical cations of oligomers, representative of a
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
1
729
H N
N H 4
CH3 N
N CH3
Figure 29 Some of the molecular structures used to interpret the EPR spectra of poly(aniline) oligomers. The molecules are labelled 1 and 4 in the same fashion as Ref. [149].
variety of poly(anilines) were measured by Grossman and co-workers [149]. Unrestricted B3LYP DFT calculations were performed with the 6-31G(d) basis set on a range of cations derived from models of poly(aniline) such as those shown in Figure 29. Geometry optimisation of the molecules reflected the steric effect of the methyl group. The methylated nitrogens resulted in a much larger angle, 631, between the plane of the outer phenyl groups and the central phenyl group, whilst the unsubstituted molecule, 1, showed a value of 421. Calculations were also performed of the isotropic hyperfine coupling constants for each molecule. This enabled a fairly unambiguous assignment of the hfccs determined from the experimental work. There was a small change to lower frequencies on forming the higher oligomers, indicating that little electron delocalisation takes place outside of a single phenyl group. A significant conclusion from their investigation is that charge conduction in the material is likely to occur as a result of hole transfer between chains, rather than along a chain.
9. SUMMARY Molecular modelling covers a wide range of techniques and the calculation of an even wider range of properties, only a few of which have been touched upon in this chapter. Although for polymers the possibility of treating a polymer chain quantum mechanically is formidable, it is clear that the modelling approach which asks the question, ‘what is the simplest model that can be used to describe these observations?’ allows calculations on monomers, dimers and oligomers to guide the interpretation of many spectroscopic observations with great success. For those systems where longer times scales and larger size scales are important, molecular mechanics and MD methods are available, but the issue of the force field and the approximations that it introduces remain significant. The key to the change in attitude to modelling and its role has to lie in the availability of mature algorithms with well-known and well-understood properties. The DFT method
730
John Kendrick
in quantum mechanics has introduced a new era in applications of quantum mechanical methods. Computers are now sufficiently powerful that all with a PC can perform good quality calculations with well-understood and quantified sources of error. That being said, the number of publications that routinely consider both the experimental measurement and the modelling are few. Only in the area of vibrational spectroscopy has the modelling methodology matured sufficiently that it is becoming routine to see interpretation of spectra through simulation. At the same time it is clear that the complexity of the phenomena being studied in polymers is such that no one single methodology gives the complete picture and it is therefore necessary to use a variety of methods including molecular simulation.
REFERENCES 1 D.W. van Krevelen, Properties of Polymers, Amsterdam, Elsevier, 1990. 2 A.A. Askadskii, Physical Properties of Polymers: Prediction and Control, Amsterdam, Gordon and Breach, 1996. 3 J. Bicerano, Prediction of Polymer Properties, New York, Marcel Dekker, 1993. 4 P. Espanol and P. Warren, Europhys. Lett., 30 (1995) 191–196. 5 P. Altevogt, O.A. Evers, J.G.E.M. Fraaije, N.M. Maurits and B.A.C. van Vlimmeren, J. Mol. Struc.-Theochem., 463 (1999) 139–143. 6 D. Nicolaides, Mol. Simul., 26 (2001) 51–72. 7 A.R. Leach, Molecular Modelling Principles and Applications, Addison Wesley Longman, 1996. 8 F. Jensen, Introduction to Computational Chemistry, Wiley, 1999. 9 J.J.P. Stewart, J. Comput. Aided Mol. Des., 4 (1990) 1–45. 10 M.F. Guest, I.J. Bush, H.J.J. Van Dam, P. Sherwood, J.M.H. Thomas, J.H. Van Lenthe, R.W.A. Havenith and J. Kendrick, Mol. Phys., 103 (2005) 719. ˚ gren, A.A. Auer, K.L. Bak, 11 T. Helgaker, H.J.A. Jensen, P. Jørgensen, J. Olsen, K. Ruud, H. A V. Bakken, O. Christiansen, S. Coriani, P. Dahle, E.K. Dalskov, T. Enevoldsen, B. Fernandez, C. Ha¨ttig, K. Hald, A. Halkier, H. Heiberg, H. Hettema, D. Jonsson, S. Kirpekar, R. Kobayashi, H. Koch, K.V. Mikkelsen, P. Norman, M.J. Packer, T.B. Pedersen, T.A. Ruden, A. Sanchez, T. Saue, S.P.A. Sauer, B. Schimmelpfennig, K.O. Sylvester-Hvid, P.R. Taylor and O. Vahtras, Dalton, a molecular electronic structure program, 2006. Available at http://www.kjemi.uio.no/ software/dalton/dalton.html 12 W.I. Spartan ‘04, 18401 von Karman Avenue, Suite 370: Irvine, CA 92612 USA. Available at http://www.wavefun.com 13 F. Neese, ORCA — an ab initio, density functional and semiempirical program package, version 2.4, revision 45, Max Planck Institut fu¨r Bioanorganische Chemie, Mu¨lheim and der Ruhr (2005). 14 M.J. Frisch, G.W. Trucks, H.B. Schlegel, G.E. Scuseria, M.A. Robb, J.R. Cheeseman, J.A. Montgomery, Jr., T. Vreven, K.N. Kudin, J.C. Burant, J.M. Millam, S.S. Iyengar, J. Tomasi, V. Barone, B. Mennucci, M. Cossi, G. Scalmani, N. Rega, G.A. Petersson, H. Nakatsuji, M. Hada, M. Ehara, K. Toyota, R. Fukuda, J. Hasegawa, M. Ishida, T. Nakajima, Y. Honda, O. Kitao, H. Nakai, M. Klene, X. Li, J.E. Knox, H.P. Hratchian, J.B. Cross, V. Bakken, C. Adamo, J. Jaramillo, R. Gomperts, R.E. Stratmann, O. Yazyev, A.J. Austin, R. Cammi, C. Pomelli, J.W. Ochterski, P.Y. Ayala, K. Morokuma, G.A. Voth, P. Salvador, J.J. Dannenberg, V.G. Zakrzewski, S. Dapprich, A.D. Daniels, M.C. Strain, O. Farkas, D.K. Malick, A.D. Rabuck, K. Raghavachari, J.B. Foresman, J.V. Ortiz, Q. Cui, A.G. Baboul, S. Clifford, J. Cioslowski, B.B. Stefanov, G. Liu, A. Liashenko, P. Piskorz, I. Komaromi, R.L. Martin, D.J. Fox, T. Keith, M.A. Al-Laham, C.Y. Peng, A. Nanayakkara, M. Challacombe, P.M.W. Gill, B. Johnson, W. Chen, M.W. Wong, C. Gonzalez and J.A. Pople, Gaussian 03, Gaussian, Inc., Wallingford, CT, 2004.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43
44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59
731
J.A. Pople, J.S. Binkley and W.J. Hehre, J. Am. Chem. Soc., 102 (1980) 939. F.R. Ditchfield, W.J. Hehre and J.A. Pople, J. Chem. Phys., 54 (1971) 724. W.J. Hehre, F.R. Ditchfield and J.A. Pople, J. Chem. Phys., 56 (1972) 2257. P.C. Hariharan and J.A. Pople, Theor. Chim. Acta, 28 (1973) 213. A.K. Wilson, D.E. Woon, K.A. Peterson and T.H. Dunning, J. Chem. Phys., 110 (1999) 7667–7676. D.E. Woon and T.H. Dunning, J. Chem. Phys., 103 (1995) 4572–4585. D.E. Woon and T.H. Dunning, J. Chem. Phys., 100 (1994) 2975–2988. D.E. Woon and T.H. Dunning, J. Chem. Phys., 98 (1993) 1358–1371. A.K. Wilson, D.E. Woon, K.A. Peterson and T.H. Dunning, Abstr. Pap. Am. Chem. Soc., 213 (1997) 60-PHYS. A.K. Wilson, T. vanMourik and T.H. Dunning, J. Mol. Struct.-Theochem., 388 (1996) 339–349. A.K. Wilson, K.A. Peterson and T.H. Dunning, Abstr. Pap. Am. Chem. Soc., 215 (1998) U530-U530. W. Kohn and L.J. Sham, Phys. Rev., 140 (1965) A1133–A1138. A.D. Becke, Abstr. Pap. Am. Chem. Soc., 195 (1988) 36-PHYS. A.D. Becke, J. Chem. Phys., 97 (1992) 9173–9177. A.D. Becke, J. Chem. Phys., 96 (1992) 2155–2160. A.D. Becke, J. Chem. Phys., 98 (1993) 5648–5652. A.D. Becke, J. Chem. Phys., 98 (1993) 1372–1377. C.T. Lee, W.T. Yang and R.G. Parr, Phys. Rev. B, 37 (1988) 785–789. B. Laird, R. Ross and T. Ziegler, Chemical Applications of Density-Functional Theory (ACS Symposium S), American Chemical Society, 1996. R.M. Martin, Electronic Structure: Basic Theory and Practical Methods, Cambridge University Press, 2004. P.P. Ewald, Ann. Physik., 64 (1922) 253. J. Kendrick and M. Fox, J. Mol. Graphics, 9 (1991) 182. R.R. Patel, R. Mohanraj and C.U. Pittman, J. Polym. Sci. Part B Pol. Phys., 44 (2006) 234–248. M. Belmares, M. Blanco, W.A. Goddard, R.B. Ross, G. Caldwell, S.H. Chou, J. Pham, P.M. Olofson and C. Thomas, J. Comput. Chem., 25 (2004) 1814–1826. M. Tsige and G.S. Grest, J. Chem. Phys., 120 (2004) 2989–2995. D. Frenkel and B. Smit, Understanding Molecular Simulation, Academic Press, San Diego, 2003. D.A. Tilbrook, B.J. Howlin and I. Hamerton, Comput. Theor. Poly. Sci., 11 (2001) 287–302. E. Henssge, D. Dumont, D. Fischer and D. Bougeard, J. Mol. Struct., 483 (1999) 491–496. R.D. Johnson III, NIST Computational Chemistry Comparison and Benchmark Database, NIST Standard Reference Database Number 101, Release 12, 2005. Available at http://srdata.nist.gov/ cccbdb K.K. Irikura, R.D. Johnson and R.N. Kacker, J. Phys. Chem. A, 109 (2005) 8430–8437. V. Barone, J. Phys. Chem. A, 108 (2004) 4146–4150. R.J. Meier and H. Vansweefelt, Polymer, 36 (1995) 3825–3829. R.J. Meier, Macromol. Symp., 119 (1997) 25–48. R.J. Meier and E. Koglin, Vib. Spectrosc., 20 (1999) 151–153. R.J. Meier, Polymer, 43 (2002) 517–522. A. Tarazona, E. Koglin, B.B. Coussens and R.J. Meier, Vib. Spectrosc., 14 (1997) 159–170. E. Koglin and R.J. Meier, Comput. Theor. Poly. Sci., 9 (1999) 327–333. M. Bertoldo, S. Bronco, C. Cappelli, T. Gragnoli and L. Andreotti, J. Phys. Chem. B, 107 (2003) 11880–11888. M. Cossi, G. Scalmani, N. Rega and V. Barone, J. Chem. Phys., 117 (2002) 43–54. D. Mathieu and A. Grand, Polymer, 39 (1998) 5011–5017. D. Mathieu, M. Defranceschi and J. Delhalle, Int. J. Quantum Chem., 45 (1993) 735–746. O.N. Tretinnikov and K. Ohta, Macromolecules, 35 (2002) 7343–7353. B.L. Baker, M. Orgill, N.L. Owen, E.H. Stephenson, G.A. Williams, J.N. Macdonald and J.E. Boggs, J. Mol. Struct., 356 (1995) 95–104. T. Tsuji, H. Ito, H. Takeuchi and S. Konaka, J. Mol. Struct., 475 (1999) 55–63. A. Silver, H. Dong, Z.F. Sun and K. Sohlberg, J. Mol. Struct.-Theochem., 731 (2005) 149–155.
732
John Kendrick
60 J. Casado, V. Hernandez, M.C.R. Delgado, R.P. Ortiz, J.T.L. Navarrete, A. Facchetti and T.J. Marks, J. Am. Chem. Soc., 127 (2005) 13364–13372. 61 J. Casado, R. Reau, V. Hernandez and J.T.L. Navarrete, Synthetic Met., 153 (2005) 249–252. 62 J. Casado, G. Zotti, A. Berlin, V. Hernandez, R.P. Ortiz and J.T.L. Navarrete, J. Mol. Struct., 744 (2005) 551–556. 63 D. Jacquemin, E.A. Perpete, V. Wathelet and J.M. Andre, J. Phys. Chem. A, 108 (2004) 9616–9624. 64 G. Beamson, J. Electron Spectrosc. Relat. Phenom., 121 (2001) 163–181. 65 M.S. Deleuze and L.S. Cederbaum, Advances in Quantum Chemistry, 35 (1999) 77–94. 66 C. Sleigh, A.P. Pijpers, A. Jaspers, B. Coussens and R.J. Meier, J. Electron Spectrosc. Relat. Phenom., 77 (1996) 41–57. 67 A.P. Pijpers and R.J. Meier, Chem. Soc. Rev., 28 (1999) 233–238. 68 E.A. Hoffmann, T. Kortvelyesi, E. Wilusz, L.S. Korugic-Karasz, F.E. Karasz and Z.A. Fekete, J. Mol. Struct.-Theochem., 725 (2005) 5–8. 69 T. Koopmans, Physica, 1 (1933) 104. 70 I.H. Hillier and J. Kendrick, J. Chem. Soc., Faraday Trans. 2, 71 (1975) 1906. 71 I.H. Hillier and J. Kendrick, J. Electron Spectrosc. Relat. Phenom., 6 (1975) 325. 72 R.L. Martin and D.A. Shirley, J. Chem. Phys., 64 (1976) 3685–3689. 73 J.C. Slater, Advances in Quantum Chemistry, 6 (1972) 1. 74 J.F. Janak, Phys. Rev. B, 18 (1978) 7165. 75 A.R. Williams, R.A. deGroot and C.B. Sommers, J. Chem. Phys., 63 (1975) 628. 76 J.V. Ortiz, Int. J. Quantum Chem., 105 (2005) 803. 77 L.S. Cederbaum and W. Domcke, Adv. Chem. Phys., 36 (1977) 205. 78 J. Schirmer and L.S. Cederbaum, J. Phys. B, 11 (1978) 1189. 79 U. Gelius, J. Electron Spectrosc. Relat. Phenom., 5 (1974) 985. 80 D.P. Chong, J. Chem. Phys., 103 (1995) 1842–1845. 81 D.P. Chong, Chem. Phys. Lett., 232 (1995) 486–490. 82 C. Bureau, D.P. Chong, K. Endo, J. Delhalle, G. Lecayon and A. LeMoel, Nucl. Instrum. Meth. Phys. Res. B, 131 (1997) 1–12. 83 C. Bureau, D.P. Chong, G. Lecayon and J. Delhalle, J. Electron Spectrosc. Relat. Phenom., 83 (1997) 227–234. 84 T. Otsuka, K. Endo, M. Suhara and D.P. Chong, J. Mol. Struct., 522 (2000) 47–60. 85 K. Endo, S. Shimada, T. Ida, M. Suhara, E.Z. Kurmaev, A. Moewes and D.P. Chong, J. Mol. Struct., 561 (2001) 17–28. 86 T. Otsuka, S. Koizumi, K. Endo and D.P. Chong, J. Mol. Struct.-Theochem., 619 (2002) 241–247. 87 T. Otsuka, S. Koizumi, K. Endo, H. Kawabe and D.P. Chong, J. Comput. Chem., 23 (2002) 394–401. 88 G. Beamson and D. Briggs, High Resolution XPS of Organic Polymers, Wiley, Chichester, 1992. 89 D.E. Ramaker, Phys. Rev. B, 21 (1980) 4608–4623. 90 D.E. Ramaker, J.S. Murday, N.H. Turner, G. Moore, M.G. Lagally and J. Houston, Phys. Rev. B, 19 (1979) 5375–5387. 91 C. Bureau, G. Deniau, F. Valin, M.J. Guittet, G. Lecayon and J. Delhalle, Surf. Sci., 355 (1996) 177–202. 92 C. Girardeaux, G. Chambaud and M. Delamar, J. Electron Spectrosc. Relat. Phenom., 77 (1996) 209–220. 93 P.S. Ho, B.D. Silverman, R.A. Haight, R.C. White, P.N. Sanda and A.R. Rossi, IBM J. Res. Dev., 32 (1988) 658–668. 94 R.C. White, R. Haight, B.D. Silverman and P.S. Ho, Appl. Phys. Lett., 51 (1987) 481–483. 95 G. Beamson, B.T. Pickup, W. Li and S.M. Mai, J. Phys. Chem. B, 104 (2000) 2656–2672. 96 M. Deleuze, B.T. Pickup and J. Delhalle, Mol. Phys., 83 (1994) 655–686. 97 M. Deleuze, J.P. Denis, J. Delhalle and B.T. Pickup, J. Phys. Chem., 97 (1993) 5115–5123. 98 M. Deleuze, J. Delhalle, D.H. Mosley and J.M. Andre, Physica Scripta, 51 (1995) 111–125. 99 R.J. Meier and A.P. Pijpers, Theor. Chim. Acta, 75 (1989) 261–270. 100 G. Beamson, D.T. Clark, N.W. Hayes, D.S.L. Law, V. Siracusa and A. Recca, Polymer, 37 (1996) 379–385. 101 A. Tarazona, E. Koglin, A.P. Pijpers and R.J. Meier, Polymer, 38 (1997) 2615–2616.
The Supporting Role of Molecular Modelling and Computational Chemistry in Polymer Analysis
733
102 B. Brena, G.V. Zhuang, A. Augustsson, G. Liu, J. Nordgren, J.H. Guo, P.N. Ross and Y. Luo, J. Phys. Chem. B, 109 (2005) 7907–7914. 103 M.E. Vaschetto, B.A. Retamal, A.P. Monkman and M. Springborg, J. Phys. Chem. A, 103 (1999) 11096–11103. 104 T. Miyamae, D. Yoshimura, H. Ishii, Y. Ouchi, K. Seki, T. Miyazaki, T. Koike and T. Yamamoto, J. Chem. Phys., 103 (1995) 2738. 105 M.S. Deleuze and L.S. Cederbaum, Int. J. Quantum Chem., 63 (1997) 465–481. 106 K. Endo, S. Koizumi, T. Otsuka, T. Ida, T. Morohashi, J. Onoe, A. Nakao, E.Z. Kurmaev, A. Moewes and D.P. Chong, J. Phys. Chem. A, 107 (2003) 9403–9408. 107 K. Endo, S. Koizumi, T. Otsuka, M. Suhara, T. Morohasi, E.Z. Kurmaev and D.P. Chong, J. Comput. Chem., 22 (2001) 102–108. 108 J. Birgerson, N. Johansson, A. Pohl, M. Logdlund, Y. Tsukahara, K. Kaeriyama and W.R. Salaneck, Synthetic Met., 122 (2001) 67–72. 109 J.M. Andre, J. Delhalle and J.L. Bredas, Quantum Chemistry Aided Design of Organic Polymers, World Scientific, Singapore, 1991. 110 J. Katajisto, T.T. Pakkanen, T.A. Pakkanen and P. Hirva, J. Mol. Struct.-Theochem., 634 (2003) 305–310. 111 C. Puglisi, F. Samperi, S. Carroccio and G. Montaudo, Macromolecules, 32 (1999) 8821–8828. 112 L. Przybilla, H.J. Rader and K. Mullen, Eur. Mass Spectrom., 5 (1999) 133–143. 113 C. Puglisi, L. Sturiale and G. Montaudo, Macromolecules, 32 (1999) 2194–2203. 114 J. Lub and G.H.W. Buning, Polymer, 31 (1990) 1009–1017. 115 G. Montaudo, C. Puglisi and F. Samperi, Polym. Degrad. Stab., 26 (1989) 285–304. 116 H.S. Cheng, P.A.C. Clark, S.D. Hanton and P. Kung, J. Phys. Chem. A, 104 (2000) 2641–2647. 117 J.E. Bushnell, P.R. Kemper, G.C. Bazan and M.T. Bowers, J. Phys. Chem. A, 108 (2004) 7730–7735. 118 A.W. Ehlers, C.G. de Koster, R.J. Meier and K. Lammertsma, J. Phys. Chem. A, 105 (2001) 8691–8695. 119 M. Reinhold, R.J. Meier and C.G. de Koster, Rapid Commun. Mass Spectrom., 12 (1998) 1962–1966. 120 E.S. Baker, J. Gidden, W.J. Simonsick, M.C. Grady and M.T. Bowers, Int. J. Mass Spectrom., 238 (2004) 279–286. 121 M.S. Giguere and P.M. Mayer, Int. J. Mass Spectrom., 231 (2004) 59–68. 122 R.J. Brill, J. Prakt. Chem., 161 (1942) 161. 123 H.M. Colquhoun and D.F. Lewis, Polymer, 29 (1988) 1902–1908. 124 H.M. Colquhoun, C.A. O’Mahoney and D.J. Williams, Polymer, 34 (1993) 218–220. 125 H.M. Colquhoun and D.J. Williams, Acc. Chem. Res., 33 (2000) 189–198. 126 H.M. Colquhoun, P.L. Aldred, A.S. Hay, A.R. Hlil, K. Miyatake and D.J. Williams, Polymer, 47 (2006) 585–590. 127 J. Wendling, A.A. Gusev, U.W. Suter, A. Braam, L. Leemans, R.J. Meier, J. Aerts, J. Van der Heuvel and M. Hottenhuis, Macromolecules, 32 (1999) 7866–7878. 128 A.D. English, J.J. Wendoloski, K.H. Gardner, J. Hirschinger and H. Miura, Abstr. Pap. Am. Chem. Soc., 199 (1990). 21-POLY. 129 A.D. English, Korea Polym. J., 4 (1996) 100–106. 130 J. Hirschinger, H. Miura, K.H. Gardner and A.D. English, Macromolecules, 23 (1990) 2153–2169. 131 H. Miura and A.D. English, Macromolecules, 21 (1988) 1543–1544. 132 K. Tashiro and Y. Yoshioka, Polymer, 45 (2004) 4337–4348. 133 E.R. DeAzevedo, T.J. Bonagamba and D. Reichert, Prog. Nucl. Magn. Reson. Spectrosc., 47 (2005) 137–164. 134 D.A. Case, Curr. Opin. Struct. Biol., 10 (2000) 197–203. 135 D. Sebastiani and U. Rothlisberger, J. Phys. Chem. B, 108 (2004) 2807–2815. 136 F. Mu¨ller-Plathe, B. Schmitz and R. Faller, Prog. Theor. Phys. Suppl., (2000) 311–319. 137 R. Faller and F. Mu¨ller-Plathe, Polymer, 43 (2002) 621–628. 138 G.A. Diaz-Quijada, N. Weinberg, S. Holdcroft and B.M. Pinto, J. Phys. Chem. A, 106 (2002) 1266–1276. 139 G.A. Diaz-Quijada, N. Weinberg, S. Holdcroft and B.M. Pinto, J. Phys. Chem. A, 106 (2002) 1277–1285.
734
140 141 142 143 144 145 146 147 148 149
John Kendrick
O. Borodin and G.D. Smith, J. Phys. Chem. B, 107 (2003) 6801–6812. O. Borodin, G.D. Smith and R. Douglas, J. Phys. Chem. B, 107 (2003) 6824–6837. J. Spevacek, J. Brus and J. Dybal, Solid State Ionics, 176 (2005) 163–167. J. Spevacek, J. Brus, J. Dybal and Y.S. Kang, Macromolecules, 38 (2005) 5083–5087. T.B. Casserly and K.K. Gleason, J. Phys. Chem. B, 109 (2005) 13605–13610. S. Naumov, I. Janovsky, W. Knolle and R. Mehnert, Nucl. Instrum. Met. Phys. Res. B, 208 (2003) 385–389. B. Yamada, D.G. Westmoreland, S. Kobatake and O. Konosu, Prog. Polym. Sci., 24 (1999) 565–630. Z. Veksli, M. Andreis and B. Rakvin, Prog. Polym. Sci., 25 (2000) 949–986. S. Camara, B.C. Gilbert, R.J. Meier, M. van Duin and A.C. Whitwood, Org. Biomol. Chem., 1 (2003) 1181–1190. B. Grossmann, J. Heinze, T. Moll, C. Palivan, S. Ivan and G. Gescheidt, J. Phys. Chem. B, 108 (2004) 4669–4672.
CHAPT ER
18 High-Throughput Analysis Robert J. Meier
Contents
1. Introduction 2. Some General Considerations on MTE and the Corresponding Analytical Needs 3. Analytical Techniques for Medium-Throughput Polymer Analysis 4. Outlook References
735 737 740 742 743
1. INTRODUCTION High-throughput screening (HTS), or Combinatorial Chemistry as it is sometimes referred to, has gained a lot of attention in pharmaceutical research. Over the last decade, these techniques, in their appropriate form, have been introduced into the chemical industries. Benefits have started to emerge, that are not only in the life-sciences field. Review papers have appeared in which the advances have been summarized [1–2], as well as papers more explicitly focusing on strategies [3–6]. Whereas high-throughput analysis (HTA) may require a substantially different approach than conventional high accuracy analysis, medium-throughput analysis methods retaining accuracy of conventional methods have become increasingly important as they may be employed in process development and process optimisation rather than lead-finding purposes (as with HTS). Benefits have been demonstrated in real-world examples, and analysis does not need to be the slow step in an organic polymer development cycle. High-throughput experimentation (HTE) is a comparatively young field, which has its roots in Combinatorial Chemistry. The goal is to produce and test as many compounds as possible in a limited amount of time. This is normally accomplished by using equipment allowing for parallel synthesis using robotics and other automated tools including data processing. An example is the testing of the potential interaction of many thousands of different chemical compounds, Comprehensive Analytical Chemistry, Volume 53 ISSN: 0166-526X, DOI 10.1016/S0166-526X(08)00418-2
r 2008 Elsevier B.V. All rights reserved.
735
736
Robert J. Meier
as potential drugs, with the active centre in an enzyme. Combinatorial Chemistry was initially a tool in pharmaceutical research, where the development of fast screening methods to test biological activity had made the synthesis of new compounds become the slow step. Therefore, synthesis of new compounds needed to be speeded up. Essential experience for this was obtained from peptide synthesis: increasing knowledge into biological mechanisms revealed a wide range of bio-active compounds, among which were many peptides. In that field, the synthesis on solid supports enabled development of simple workup protocols by rinsing with excess reagents used to drive reaction to completion, without any significant product loss. Another example from the ‘‘bio-world’’ is the production of micro-organisms for optimum product yield and quality. An example could be micro-organisms for the production of penicillin, whereas recently there have been developments to explore routes to produce monomers for synthetic polymers by means of micro-organisms. Diversity in the micro-organisms to be tested can be achieved either by genetic engineering or by random mutagenesis. Why do we mention all this in a book about polymer characterization and analysis? In the 1990s it became clear that Combinatorial Chemistry could also have a function in traditional chemistry, and later also in materials research. Combinatorial means based on combination, and in pharmaceutical research this is the case because synthesis of different compounds is accomplished starting from a few building blocks, in particular peptides. Synthesis in traditional chemistry does not work in the same simple straightforward way, e.g., the synthesis of ligands for homogeneous catalysis or the preparation of a series of different but similar materials such as a set of copolymers with differing ratios of comonomers A and B. Therefore, the application of Combinatorial Chemistry in chemistry and materials science, whenever feasible, had to be developed separately from what had happened beforehand in the pharmaceutical area. Moreover, in pharma-related research the screening activities mostly involve obtaining ‘‘yes’’ or ‘‘no’’ answers with respect to activity. In chemistry and materials science, particularly in industrial applications, we often want more precise, quantitative, statements on properties such as activity and selectivity for a catalyst or modulus and tensile strength for a material. Whether this would become a feasible approach had to be investigated. First of all the question arose ‘‘Is Combinatorial Chemistry another ‘Hype’?’’ and ‘‘Have there been many great success stories in the pharma area?’’ The latter does not seem to be in question when considering the huge investments in Combinatorial Methodology in that industrial segment. In addition, it was questioned, ‘‘Whether combinatorial chemistry will have as many uses outside the realm of drugs as in it is not yet clear’’ (as reported in the newspaper, The Economist, March 1998). However, recently we have seen a tremendous growth in the number of publications and patent applications. In particular, e.g., Symyx Technologies, Inc (Santa Clara, USA), is very active in patenting HTS related techniques [1]. Before we continue explicitly discussing high-throughput techniques and examples in the polymer field, we will first provide some definitions that may be
High-Throughput Analysis
737
helpful in understanding the difference between combinatorial or HTS in different fields of application. Combinatorial Chemistry is a set of HTS methods applied in the pharmaceutical industry, mainly aiming at lead-finding in terms of ‘‘yes/no’’ answers. The number of experiments is typically of the order of a million per annum. To distinguish the other approach applicable in chemistry and materials science, one may introduce HTE, which in turn may be subdivided into: (i) (ii)
HTS: speed-up by more than a factor of 50, to find new functionality (e.g., better catalyst), thus for lead-finding (research) purposes and MTE – medium-throughput experimentation: this is the speed-up of process development. Speed-up factor of about 5–50. The typical sample flow is 100 samples a day. Quality and type of output is similar to traditional experimentation.
The corresponding high-speed analysis is also known as HTA. Other terms one may encounter include (i) (ii)
Primary screening: lead-finding, search for new functionality, e.g., finding new catalysts. Requires a (very) high number of experiments. Secondary screening: lead-optimisation, applied in process development. Large (compared to the traditional number of roughly one or two experiment(s) a day) but not a high number of experiments.
From these definitions one may corroborate the intention of HTS in chemistry and materials science. The total speed-up factor of this part of the R&D (Research and Development) process, as stated earlier, is between 5 and 50, but contrary to most of the pharma applications true (semi-) quantitative answers will result. As a result, this approach is essentially applicable in any segment of R&D. On the other hand, this approach requires methods of experimentation that have almost the same if not the same accuracy as in the traditional one-experiment-at-the time approach. This is key as: (i) in process optimisation accuracy is key and (ii) in research, also in academic research, accuracy is important as some polymer properties do not span a wide range of values (e.g., the elastic modulus of amorphous polymers) or may depend critically on molecular weight distribution or molecular order.
2. SOME GENERAL CONSIDERATIONS ON MTE AND THE CORRESPONDING ANALYTICAL NEEDS As we argued earlier, application in chemistry and materials science usually requires quantitative information. When considering methods of analysis, one may discriminate between very fast but less accurate methods to get qualitative answers, and slower but more accurate methods yielding true quantitative information. The former one is the class of methods that can be speeded up to a high extent, i.e., thousands of samples a day. This may apply to techniques
738
Robert J. Meier
including mass spectrometry (MS) (e.g., matrix-assisted laser desorption ionisation–time-of-flight, MALDI-ToF) and thermal analysis. The other class comprises methods that do not allow for such high-throughput numbers, at least not when the accuracy needs to be more or less retained. For instance, an average molecular weight can be obtained much quicker than a full molecular weight distribution, but the latter is much more informative when comparing the properties of a series of polyolefins synthesized using a library of metallocenebased catalysts. Since traditional analytical approaches can be rather easily adapted to a method allowing for the analysis of typically 100 samples a day, this is the approach we will focus on, as this will accommodate most sample streams. Originally it was thought that HTE in chemistry and materials science would involve the same high number of samples a day as in the pharma area. However, more or less random generation of samples is not only much more difficult in the chemistry and materials science segment than it is in the pharma arena, but it is also highly expensive. But even more importantly, we generally want more than just ‘‘yes’’ or ‘‘no’’ answers. An approach in which MTE is combined with tools such as Experimental Design, also known as Design of Experiments (DoE) [7], seems much more promising. Next to the application in research activities looking for new compounds, the more accurate medium-throughput analysis can be applied in process and product optimisation. Let us summarize what MTE may provide compared to traditional ways to perform experiments in R&D. Coming from: the practice of 2–3 experiments/day; the analysis being time consuming and therefore often not extensive, the latter particularly applies in an industrial environment; the impossibility to test all possible relevant conditions, e.g., in polymerisation the catalyst type, the catalyst concentration, the catalyst/co-catalyst ratio, the activator type and concentration, monomer type, pressure and temperature; while MTE allows for: two orders of magnitude higher screening rate (typically 100–200 reactions/ samples a day); the rapid screening of catalysts or polymer samples, under real experimental conditions; analysis and data treatment at the same rate; cost effectiveness, i.e., the cost of analysing 100 samples a day is much less than the cost involved in analysing 100 times a single sample in the traditional way of operating an analytical technique. For the synthetic chemistry part, this is accomplished by using parallel reactors (a chemical reaction takes time, say 30 min), involving automated injection of all components. Such equipment had already been developed for pharma R&D and is therefore, widely available. For an overview see, e.g., Tuchbreiter et al. [4] and Schmatloch et al. [8]. Producing materials, e.g., compounds, is less trivial. To produce a series of different polymer samples, e.g., blends, an approach using a mask, see, e.g., Figure 1, is often applied.
High-Throughput Analysis
739
Figure 1 Left: illustration of the application of a mask to produce different ‘‘samples’’. Right: FT-IR images of the carbonyl band of poly(vinyl cinnamate), showing different levels of crosslink density as revealed from a decrease in conjugated carbonyls. Reproduced from Rafferty et al. [9], Copyright 2002, with permission from the Society for Applied Spectroscopy.
Rafferty et al. [9] have used Fourier transform infrared (FT-IR) spectroscopy imaging to characterize a series of photo-cross-linked poly(vinyl) cinnamate systems. This application is related to research into chemical sensors. By using a mask system, commonly used to make a series of different related materials on a single substrate, a variety of samples is produced exhibiting various cross-linking densities. The mask approach is illustrated in Figure 1. By rotating the mask and applying a different UV exposure time in the second step, each small square on the substrate becomes a different sample. The IR image of such an array, part of which is shown on the right in Figure 1, illustrates that whereas the intensity of the alkene band in the poly(vinyl) cinnamate structure is an obvious choice to monitor cross-linking, the carbonyl band can be used equally well. Lateral spatial resolution was about 6 mm and total acquisition time for a single image was 3.5 min. For formulated compounds small extruders need to be developed [10], while the application for coatings requires dedicated equipment [5]. An additional issue we need to discuss is sample preparation for analysis. In some cases this is rather trivial (dissolving a polymer for molecular weight analysis using gel permeation chromatography (GPC)), whereas in other cases it is far from trivial, e.g., the synthesis and analysis of a series of polymer coatings. Regarding the automation of a sample flow, in general one may wish to consider to what extent automation, e.g., robotisation, makes applications sense in the respect of sample analysis in MTE (up to 100 samples a day). Robots and the accompanying software are not inexpensive, and when not all equipment (synthesis and analysis, including sample handling) is available in one room, one
740
Robert J. Meier
may wish to consider whether automating the entire sample flow is cost-effective. Of course the final solution will depend on a variety of factors involved locally. And, importantly, as HTE does not make sense when one of the steps in the entire sample flow is still very slow, HTE and Combinatorial Chemistry in full effectiveness means a joint effort between all disciplines involved! Last but not least, when you start working in a ‘‘Combinatorial’’ way, you may start to think in a different way and you may revise your experiments. This has been the practice in laboratories where HTE methods have been implemented. The change in mind-set is perhaps the most important, but also the most difficult step, in moving towards HTE. In this context we should recognize that many scientists, and certainly also analytical chemists and those involved in analyzing materials properties, are often somewhat conservative. It is all but to quickly said that MTE or HTE methods of analysis will lead to rubbish answers. Practice, meanwhile, has taught us differently. In fact in some cases one learns the traditional, one sample at the time, method of analysis is not as accurate or reliable as one has thought it was. So HTE can be an excellent way of once more refreshing our thinking of why we do analysis in the way we have been used to performing these.
3. ANALYTICAL TECHNIQUES FOR MEDIUM-THROUGHPUT POLYMER ANALYSIS To properly characterize a polymer, more than one technique is required. As in traditional polymer analysis, some techniques are suitable for determining molar mass (distributions), others for chemical constitution, e.g., monomer composition, branching, whereas still others may be employed in determining properties such as melting point, crystallinity and other morphological features. Almost all analytical techniques applied in polymer analysis can be adapted to allow for medium-throughout application. Some techniques are already inherently fast. This obviously applies to analytical techniques that have been used for on-line monitoring, e.g., mid-IR and near-infrared (NIR) spectroscopy. For such techniques the installation of an automatic sample changer might be sufficient to achieve throughput of 100 samples a day. Optical spectroscopies, including UV-visible, fluorescence spectroscopy, IR, NIR and Raman spectroscopy are easily tuned to allow the screening of 100 samples a day. For example, the HTSXT unit from Bruker (Bruker Optics GmbH, Ettlingen) provides the capability of either transmission or diffuse reflection IR measurements to be performed in an automated way, both on the basis of micro-plates derived from the micro-titer plates used in bio- Combinatorial Chemistry. In specific cases, however, sensitivity might be insufficient, particularly for Raman spectroscopy where also fluorescence may interfere. IR may be used in transmission mode using a sample changer or in reflection mode (attenuated total reflection (ATR)). The latter mode employs such as what is commonly known as a ‘‘Golden Gatet’’ (Specac, Orpington) accessory in which a polymer sample is pressed onto an ATR crystal. This method avoids sample preparation in the form of KBr pellets or casting polymer films. IR and Raman spectroscopies may also be applied in
High-Throughput Analysis
741
conjunction with chemometric techniques to ‘‘determine’’ mechanical properties; examples will be presented later. Another important technique is the thermal analysis technique of differential scanning calorimetry (DSC). Current high-speed DSC equipment (sometimes also referred to as hyper-DSC) allows for rapid heating (up to 5001C/min) and cooling of (small) samples and therefore an increased rate of analysis per sample [11]. Simultaneously, the rapid heating more strongly resembles real-life situations as they occur in, e.g., polymer extrusion. There are several known techniques to measure molecular weight and molecular weight distribution (see Chapter 6), e.g., GPC or Size Exclusion Chromatography (SEC), MALDI-ToF-MS and light scattering and viscosity measurements. All except MALDI-ToF-MS are also suitable to characterize polyolefins. Starting with the GPC method, there are two approaches reported that will be mentioned here. In HTE mode one may envision the determination of the (average) molecular weight, whereas in the MTE approach the molecular weight distribution and all its moments (Mw, Mz, Mn, see Chapter 6) are determined. Symyx Technologies have described an approach to perform HT MS [12]. The more traditional way to determine molecular weight, and more interestingly molecular weight distribution, is by GPC, which suffices for MTE and provides the full Mw curve. As with other chromatographic techniques, there is a straightforward approach to speed up the analysis time, namely by shortening the column and or increasing the flow rate. Regarding the former, this is feasible when the separation between different molecular weights is sufficiently retained. The second issue is a critical one when studying long polymer chains such as is common for polyolefins, as sample degradation will readily occur when the flow rate is too high. But when just a short, modified column is applied, very satisfactory results can be obtained. Such short columns have become available commercially (Polymer Laboratories (now part of Varian, Inc., Amherst) [13] and PSS (Polymer Standards Service GmbH, Mainz) [14], see also Pilz [15]). Designs may be different compared to traditional columns, unique features being a new packing material with better flow properties and a different column aspect ratio to increase the flow rate. Figure 2 shows a chromatogram for polystyrene standards, revealing the sufficient accuracy and precision of the high-speed SEC column compared to traditional SEC [16]. It is clear from those data that the high-speed data are very satisfactory and do not differ much from conventional SEC measurements. Actually, for polyolefins, requiring hightemperature SEC, which is a little more elaborate, the spread in values between different laboratories is often larger than the differences found between a conventional four-column SEC set-up and high-speed short-column SEC. Gabriel et al. [17] reported on a comparison between molar mass distributions from conventional and fast SEC for three high-density polyethylene (HDPE) samples. The authors reported a small but systematic shift between the two molar mass distributions, which are reflected in the molar mass averages. MALDI-ToF-MS is a powerful technique capable of obtaining information on molecular weight, molecular weight distribution and end-group analysis [18–19], see also Chapters 5 and 6. This technique has not only become a workhorse in the
742
Robert J. Meier
Figure 2 Chromatogram from conventional SEC column compared to high-speed SEC column tested on an identical instrument with polystyrene standards in tetrahydrofuran (THF). (See Color Plate Section at the end of this book.)
screening of biological assays [20,21], but is also useful for screening synthetic polymer libraries. An illustration of application to synthetic polymers was presented by Hoogenboom et al. [22]. The intention of this book was not to discuss macroscopic properties, which includes mechanical, electrical and optical properties. Therefore tensile testing and many other tests are not discussed in this chapter. However, when aiming for HT or MT analysis, alternative analytical approaches might be more appropriate. An example is the use of the Raman spectra of polyolefins to predict mechanical properties [23]. Using multivariate data analysis, the Raman spectra of a series of metallocene-catalyzed polyethylenes were used to establish a correlation between features in the Raman spectrum and polymer density, the number of methyl branches per 1,000 C atoms, the elastic modulus and the yield strength. The correlations for the mechanical properties are shown in Figure 3. It may be argued that the correlation is far from perfect, but it should be realized that this application focuses on HTA, e.g., 100 samples or more per day, for the purpose of screening potentially useful catalysts. Alternatively, NIR spectroscopy has been applied to relate NIR data to mechanical properties [4]. A multivariate data analysis was performed on a series of commercial ethene copolymers with 1-butene and 1-octene. For the density correlation, a coefficient of determination better than 99% was obtained, whereas this was 97.7% for the flexural modulus, and only 85% for the tensile strength. A rapid characterization of the viscosity of waterborne automotive paint was reported by Ito et al. [24]. FT-Raman spectroscopy in conjunction with partial least squares regression (PLS) was applied and led to a reasonable correlation.
4. OUTLOOK The current trend to innovation, as well as future needs to more sustainable solutions, requires development of new polymeric materials. Other than new
High-Throughput Analysis
743
Figure 3 Chemometric calibration of the elastic modulus (left) and the yield stress (right) of a series of polyethylenes. Reproduced from Gabriel et al. [23], Copyright 2003, with permission from Wiley-VCH Verlag GmbH.
polymers, environmental restrictions will primarily lead to using traditional polymers, including polyolefins and nylons, and polyester, for resins and coatings. Additives, processing conditions and compounding will lead to new materials satisfying all required demands. To develop such materials, it is expected that large numbers of samples will need to be tested, as we are still far from ab initio materials design. MTE methods, leading to strongly increased throughput, while simultaneously retaining quantitative comparison, may be expected to play an important role. As we hope we have briefly illustrated in this chapter, it is actually not too difficult to implement MT methods of analysis.
REFERENCES 1 B. Jandeleit, D.J. Schaefer, T.S. Powers, H.W. Turner and W.H. Weinberg, Angew. Chem. Int. Ed., 38 (1999) 2494–2532. 2 K.C. Nicolaou, R. Hanko and W. Hartwig, Handbook of Combinatorial Chemistry, Volume 2, Drugs, Catalysts, Materials, Wiley-VCH, 2002. 3 J.N. Cawse, Acc. Chem. Res., 34 (2001) 213–221. 4 A. Tuchbreiter, J. Marquardt, B. Kappler, J. Honerkamp, M.O. Kristen and R. Mu¨lhaupt, Macromol. Rapid Commun., 24 (2003) 47–62. 5 R. Iden, W. Schrof, J. Hadeler and S. Lehmann, Macromol. Rapid Commun., 24 (2003) 63–72. 6 K.P. Peil, D.R. Neithamer, D.W. Patrick, B.E. Wilson and C.J. Tucker, Macromol. Rapid Commun., 25 (2004) 119–126. 7 G.E.P. Box, W.G. Hunter and J.S. Hunter, Statistics for Experimenters: An introduction to Design, Data Analysis and Model Building, Wiley, NY, 1978. 8 S. Schmatloch, M.A.R. Meier and U.S. Schubert, Macromol. Rapid Commun., 24 (2003) 33–46. 9 D.W. Rafferty, J.L. Koenig, G. Magyar and J.L. West, Appl. Spectrosc., 56 (2002) 1549. 10 R.A. Potyrailo, R.J. Wroczynski, J.E. Pickett and M. Rubinsztajn, Macromol. Rapid Commun., 24 (2003) 123–130. 11 T.F.J. Pijpers, V.B.E. Mathot and B. Goderis, Macromolecules, 35 (2002) 3601–3613. 12 EP 01019947 B1 (2002), inventors H. Weinberg, E.W. McFarland, P. Cong and S. Guan.
744
Robert J. Meier
13 Polymer Laboratories Rapid Screening column, Polymer Laboratories Ltd., Shropshire, U.K. Available at http://www.polymerlabs.com/ 14 PSS HighSpeed columns, Polymer Standards Service GmbH, 55120 Mainz, Germany. Available at http://www.polymer.de/ 15 P. Kilz, High speed SEC methods, In: J. Cazes (Ed.), Encyclopedia of Chromatography, online edition, Marcel Dekker, New York, 2002. 16 H. Pasch and P. Kilz, Macromol. Rapid Commun., 24 (2003) 104–108. 17 C. Gabriel, D. Lilge, H.M. Laun, M. Rullmann, D. Schulze and C. Friedrich, Macromol. Rapid Commun., 25 (2004) 249–252. 18 M.F.W. Nielen, Mass Spectrom. Rev., 18 (1999) 309–344. 19 S. Weidner, G. Ku¨hn and J. Friedrich, Rapid Commun. Mass Spectrom., 12 (1998) 1373–1381. ¨ nnerfjord, J. Nilsson, M. Bengtsson, T. Laurel and G. Marko-Varga, Anal. Chem., 72 20 S. Ekstro¨m, P. O (2000) 286–293. 21 A. Graven, P.M. St.-Hilaire, S.J. Sanderson, J.C. Mottram, G.H. Coombs and M. Meldal, J. Comb. Chem., 3 (2001) 441–452. 22 R. Hoogenboom, M.W.M. Fijten, M.A.R. Meier and U.S. Schubert, Macromol. Rapid Commun., 24 (2003) 92–97. 23 C. Gabriel, D. Lilge and M.O. Kristen, Macromol. Rapid Commun., 24 (2003) 109–112. 24 K. Ito, T. Kato and T. Ona, Vibr. Spectrosc., 35 (2004) 159–163.
SUBJECT INDEX
AAS, see Atomic absorption spectrometry; Techniques and Tests Ab initio methods, see Molecular modelling Additive analysis, 9, 562–605 atomic absorption spectroscopy (AAS), 563–567, see also Techniques and Tests differential scanning calorimetry (DSC), 565, see also Techniques and Tests gas chromatography ( GC), 565–567, see also Techniques and Tests GC-MS, 566 Inductively coupled atomic emission spectroscopy, ICP-AES, 571, see also Techniques and Tests liquid chromatography-mass spectrometry, LC-MS, 570–571, see also Techniques and Tests mid-infrared spectroscopy, 567–570, see also Techniques and Tests scanning electron microscopy-energy dispersive analysis, SEM/EDA, 571, see also Techniques and Tests thermogravimetric analysis, TGA, 572, see also Techniques and Tests X-ray fluorescence spectroscopy, XRF, 573, see also Techniques and Tests Additives, 87–117 anti-blocking agents, 92, 573 anti-fogging agents, 111, 573 antimicrobial agents, 574 anti-oxidants, 98–103, 574–582 anti-ozonants, 103–104, 582 antistatic agents, 93–94, 582–584 biocides, 109–110 blowing or foaming agents, 95–96, 584–585 cross-linking agents, 585–587 cure accelerators, 585–587 cure reaction products, 594, 598, 599 degradation additives, 111–112 dyes, see pigments and dyes below fillers, 588 flame retardants, 107–109, 588 heat stabilisers, 88–91
impact modifiers, 588 lubricants, 91–92, 588–589 mechanical property modifiers, 112–114 metal deactivators, 589 mould-release agents, 92–93 nucleating agents, 589, 591 pigments and dyes, 591 plasticisers, 94–95, 592 slip and anti-slip agents, 92, 588–589 surfactants, 593 ultra-violet (UV) stabilizers, 104–107, 594 Adhesion, 677–678 Advanced materials, 84 Aesthetics, 81, 87, 110, 115–117, 608–618 AFM, see Atomic force microscopy; Techniques and Tests Ageing, see Degradation Amorphous, 18, 70–74 Analytical competence, 3–6 Antioxidants, 483–487 Atactic, see Tacticity Atomic absorption spectrometry, AAS, see Techniques and Tests Atomic force microscopy, AFM, see Techniques and Tests ATR, see Attenuated total reflection; Techniques and Tests Attenuated total reflection, ATR, see Techniques and Tests Berry plot, 224 Blend(s), see Polymer Blob concentration, 131 tensile, 131 thermal, 131 Bolland-Gee scheme, see Degradation Branching, 139–153 hyperbranched, 7, 23, 140–141, 163–165 long-chain, LCB, 7, 23, 39, 139 short-chain, SCB, 7, 23, 39, 139 star polymers, 140 Brillouin scattering, see Techniques and Tests
745
746
Subject Index
Capillary electrophoresis, see Techniques and Tests Carbonyl index, see Techniques and Tests Carothers equation, 55 Chain ends, see Polymer, end groups Chain folding, 20, see also Polymer chain structure, chain length Chain length, 15–17, 27, see also Polymer chain structure, chain length Chain polymerization, 34 Chain radius of gyration, 126 Chain structure, see Polymer chain structure, Characterisation, 3, 15 Chemical titration, see Techniques and Tests Chemiluminescence, CL, 463–483, see also Degradation and Techniques and Tests Cis-trans, see Isomerism 15–17, 35, 70 CL see Chemiluminescence; Techniques and Tests Coatings, 81–84 Coil structure/coil size, 127–133 hydrodynamic radius, Rh, 130, 132–133 radius of gyration, Rg, 126, 132–133 self-avoiding walk, SAW, 127 Comonomer(s), see also Polymer, copolymer, 7, 48, 50, 141, 156, 159, 161 Competance, analytical 3–6 Composites, 84–85 Composition, 7 Computational chemistry, see Molecular modeling Configuration, 29–30 Conformation, 7, 30–33, 127, 134, 137 Contaminant analysis, see Failure analysis Copolymer(s) , 50–53, see also Polymer, alternating, 68 block, 52–53 graft, 51–52, 68 random, 68 sequencing, 7, 24, 715 Critical oxygen index, COI, see Limiting oxygen index Cross-linking, 7, 24, 57–58, 69 Crystallinity, crystallisation, 72–73, 153–163, 257, 338, see also Lamellae amorphous content, 3, 8, 353–354 phase analysis, 8–9, see also phase structure Crystallisation-melt temperature, Tm, 19–21, 70–71, 72, 338 Cure, 681–682
Defect analysis, see Failure analysis Degradation, 8, 58–62, 388–447, 452–496, 500–521, 679 Bolland-Gee scheme, 462, 470 carbonyl index, 8, 394–397, 410, see also Techniques and Tests chemiluminescence, CL, 463–496 chemically initiated electron exchange luminescence, CIEEL, 466 degradation cascade, 500–501 differential photocalorimetry, DPC, 438, see also Techniques and Tests differential scanning calorimetry, DSC, 436–438, 476–478, see also Techniques and Tests diffusion-limited oxidation, DLO, regime, 501 dissociation energies, 453–454 electron spin resonance, ESR, 500–521, see also Techniques and Tests electron spin resonance imaging, ESRI, 510–521, see also Techniques and Tests fluorescence spectroscopy, 418–422, see also Techniques and Tests gas chromatography, GC, 442–443, see also Techniques and Tests hydroperoxide(s), 456–458, 476, 500 induction period, 458, 461 liquid chromatography, LC, 443–447, see also Techniques and Tests mass spectrometry, 422–429, see also Techniques and Tests melt flow index, 399–402, see also Techniques and Tests mid-infrared spectroscopy, 402–414, see also Techniques and Tests molecular modeling, 697 nuclear magnetic resonance spectroscopy, NMR, 429–433, see also Techniques and Tests oxidative-induction time, OIT, 390–393, see also Techniques and Tests oxygen uptake, 390–393, see also Techniques and Tests phosphorescence spectroscopy, 418–422, see also Techniques and Tests Raman spectroscopy, 414–418, see also Techniques and Tests secondary ion mass spectrometry, SIMS, 435–436, see also Techniques and Tests
Subject Index
staining, see also Techniques and Tests, 397–399 thermogravimetric analysis, TGA, 438–442, see also Techniques and Tests titration, 435–436, see also Techniques and Tests uv spectroscopy, 418–422, see also Techniques and Tests X-ray photoelectron spectroscopy, XPS, 433–435, see also Techniques and Tests Degree of polymerization (dp), 7, 68 Delamination, 679, 681 Dendrimer, 24, 140 Density functional methods, DFT, see Molecular modeling Density, 8, 260–261 Dielectric relaxation, see Techniques and Tests Differential photocalorimetry, DPC, see Techniques and Tests Differential scanning calorimetry, DSC, see Techniques and Tests Direct insertion probe pyrolysis mass spectrometry, DPMS, see Techniques and Test, mass spectrometry Distribution functions, 208–211, 352 DPC, see Differential photocalorimetry; Techniques and Tests DSC, see Differential scanning calorimetry; Techniques and Tests EDS, see Energy dispersive spectroscopy; Techniques and Tests Elastomers 74–77, 338–376 Electron spectroscopy for chemical analysis, ESCA, see Techniques and Tests Electron spin resonance spectroscopy, ESR, see Techniques and Tests End-group, 7, 27–28, 171–202, 207 Energy dispersive spectroscopy, EDS, see Techniques and Tests Entanglement(s), 27, 339, 350–351 ESCA, see Electron spectroscopy for chemical analysis; Techniques and Tests ESR, see Electron spin resonance spectroscopy; Techniques and Tests ESRI, see Electron spin resonance imaging see Techniques and Tests Evolved gas analysis, EGA, see Techniques and Tests
747
Failure analysis, 9, 607–674 aesthetics, 608–618 contaminant and defect analysis, 9, 618–647 delamination, 679, 681 FFF, see Field-flow fractionation; Techniques and Tests Fibres, 77–79 Fibril, 21 Field-flow fractionation, FFF, see Techniques and Tests Film(s), 79–81 Fluorescence spectroscopy, see Techniques and Tests Fourier transform infrared spectroscopy, FTIR, see Techniques and Tests Fracture, 679 FTIR, see Fourier transform infrared spectroscopy; Techniques and Tests Gas chromatography, GC, see Techniques and Tests GC, see Gas chromatography; Techniques and Tests Gel effect, 39–41 Gel permeation chromatography, GPC, see Techniques and Tests; see also Size exclusion chromatography, SEC Gelation, see also Techniques and Tests, 352 Gel-point determination, see Techniques and Tests, Glass transition temperature, Tg, 17–19, 28, 71 GPC, see Gel permeation chromatography; Techniques and Tests; Size exclusion chromatography, SEC Graft copolymers, see Copolymers Heat distortion temperature, HDT, 73 High performance liquid chromatography, HPLC, see Techniques and Tests High performance liquid chromatography, HPLC, see Liquid chromatography High performance polymers, 84–87 High-throughput analysis, HTA, 735–743 Hindered amine stabilizers, HAS, 459, 502–504, 517 Homopolymer , 21–23 HPLC, see High performance liquid chromatography; Techniques and Tests Hydroperoxides, 397–399, 402, 456–459, 476, 500, see also Degradation
748
Subject Index
ICP-AES, see Inductively coupled plasma atomic emission spectroscopy; Techniques and Tests ICP-MS, see Inductively coupled plasma mass spectrometry; Techniques and Tests IGC, see Inverse gas chromatography; Techniques and Tests Induction period, 458, 461 Inductively coupled plasma atomic emission spectroscopy, ICP-AES, see Techniques and Tests Inductively coupled plasma mass spectrometry, ICP-MS, see Techniques and Tests Infrared, IR, see Techniques and Tests carbonyl index, see Techniques and Tests IR-microscopy, 9, 308, 537 mid-infrared, mid-IR, see Techniques and Tests near-infrared, NIR, see Techniques and Tests Interphase (crystalline-amorphous), 271–274, see also Phase structure Inverse gas chromatography, IGC, see Techniques and Tests Iodometric test, see Techniques and Tests Ionomer, 76 IR, see Infrared Isomerism 7, 27, 29, 714 Isotactic, see Tacticity Kevlars, see Polymer, Thermoplastic, Poly(p-phenylene terephthalamide) Kuhn unit, Kuhn (step) length, 7, 125–127 Ladder polymers, 85 Lamellae, 20–21, 53, 256, 280–284 Lamellar thickness, 284–286 Laminates, 545–549 Laser enhanced ionization spectroscopy, LEIS, see Techniques and Tests LC, see Liquid chromatography; Techniques and Tests LC-CC, see Liquid chromatography under critical conditions; Techniques and Tests LEIS, see Laser enhanced onization spectroscopy; Techniques and Tests Light scattering, see Techniques and Tests Limiting oxygen index, LOI, 85 Liquid chromatography under critical conditions, LC-CC, see Techniques and Tests
Liquid chromatography, LC, see Techniques and Test Liquid crystalline polymers, 74, see also Liquid-crystalline elastomers Longitudinal acoustic mode, LAM, 262, 284–286 disordered LAM, 263, 267 Macromers, 68 telechelic macromers/telechelic polymers, 68 Magnetic resonance imaging, MRI, see Techniques and Tests MALDI-MS, see Matrix-assisted laser desorption mass spectrometry; Techniques and Test MALDI-TOF-MS, see Matrix-assisted laser desorption time-of-flight mass spectrometry; Techniques and Tests Maltese cross, 20, 274, 275 Matrix-assisted laser desorption mass spectrometry, MALDI-MS, see Techniques and Tests Matrix-assisted laser desorption time-offlight mass spectrometry, MALDITOF-MS, see Techniques and Tests Medium-throughput analysis, 740–742 Melt flow index, MFI, see Techniques and Tests Membrane osmometry, see Techniques and Tests MFI, see Melt flow index; Techniques and Tests Microscopy/Microscopies, see Techniques and Tests Microstructure, 14–62 Miscibility, 71, 130–131 Molar mass, see Molecular weight, Molecular density functional methods, see Molecular modelling Molecular dynamics, see Molecular modelling Molecular mass distribution, see Molecular weight distribution Molecular mass, see Molecular weight Molecular mechanics, see Molecular modelling Molecular modelling, 686–730 ab initio methods, 689–690 Auger spectroscopy, 703–712 electron spin resonance, ESR, 727–729 infrared spectroscopy, 693–703 mass spectrometry, 712–718 metal-polymer interactions, 708–709
Subject Index
molecular density functional methods, 690 molecular dynamics, 692–693 molecular mechanics, 691–692 Monte Carlo methods, 692–693 Nuclear magnetic resonance, NMR, 722–727 photoelectron spectroscopy, PES, 703–712 quantum mechanics, 687–688 Raman spectroscopy, 693–703 semi-empirical methods, 688–689 solid-state density functional methods, 690–691 X-ray diffraction, 718–722 Molecular orientation, see Orientation Molecular weight distribution, 7, 15, 71, 148, 205–247, see also Techniques and Tests Molecular weight, 7, 15, 205–247, 478 Monomer(s), 7, 15–17, 594 Monte Carlo methods, see Molecular modeling Mooney-Rivlin isotherms, 351 Morphology, 3, 255–286 supermolecular, 274–286 MRI, see Magnetic resonance imaging; Techniques and Tests Network, 8, 69, 338–376 affine model, 345–346 bimodal networks, 359–364 elastic free energy, 344 elastic modulus, 344–345 filler reinforcement, 354–355 force-temperature relations, 358–359 gelation, 352 liquid-crystalline elstomers, 365–370 phantom network model, 346–347 reduced stress, 344–345 stress-strain isotherms, 352–353 trimodal networks, 364–365 NMR, see Nuclear magnetic resonance spectroscopy; Techniques and Tests Nuclear magnetic resonance spectroscopy, NMR, see Techniques and Tests OIT, see Oxidative-induction time; Techniques and Tests Oligomers 15, 68 Optical microscopy, see Techniques and Tests Orientation, 8, 32, 72, 295–333 biaxial distribution, 299–300 birefringence, 8, see also Techniques and Tests compensation method, 303–304 refractometry method, 303 transmission method, 304–305
749
fluorescence spectroscopy, 322–325 infrared linear dichroism, IRLD, 305–313 reflection IRLD, 309–312 time-resolved IRLD, 312–313 transmission, IRLD, 307–309 nuclear magnetic resonance spectroscopy, 325–327 orientation distribution function, ODF, 296–297 Raman spectroscopy, 313–322 uniaxial distribution, 300 X-ray diffraction spectroscopy, 328–333 Osmometry, membrane, see Techniques and Tests vapour pressure, see Techniques and Tests Oxidation, see Degradation; Techniques and Tests Oxidative-induction time, OIT, see Degradation; Techniques and Tests Oxygen uptake, 8, 393–394, see also Techniques and Tests Paint(s), 81–84 Persistence length, 7, 125–127 PES, see Photoelectron spectroscopy; Techniques and Tests Phase structure, 255–274 crystalline, 257 interphase, 271–274 liquid-like, 267–271 Phosphorescence, see Techniques and Tests Photoelectron spectroscopy, PES, see Techniques and Tests Polycondensation, see Polymerisation, Step Polydispersity index, 17 Polyethylene (PE), 16, 17, 22, 23, 27, 32, 39, 266, 268, 272, 285, 394, 402 high density PE, HDPE, 46, 49 low density PE, LDPE, 23, 39, 49, 397, 409, 435 linear low density PE, LLDPE, 23, 46, 49, 153–160, 265 Polymer chain structure, 7, 23, 123 branching, 7, 139–152, 163 chain folding, 19 chain length, 7, 15, 27, 723 Kuhn length, 7, 125–127 persistence length, 7, 125–127 radius of gyration, 125, 126 stiffness, 723–724 comonomer, 7 composition, 7 configuration, 27, 29–30, 137–138 conformation, 7, 27, 30–33, 137–138
750
Subject Index
copolymer sequencing, 7, 24, 161–163 cross-linking, 7, 24, 69 degree of polymerization (dp), 7 end group, 7, 27–28, 171–202, 207 elasticity, 341–344 entanglements, 27 helices, 33, 138 isomerism, 7, 27, 29 Kuhn unit/length, 7, 125–127 lamellae, see lamellae molecular weight, 7, 15 molecular weight distribution, 7, 15 monomer, 7, 15 persistence length, 7, 125–127 sequence length, see Coplymer(s), sequencing stereoregularity, 7, 135–138 tacticity, 7, 29–30, 46, 134–139 unsaturation, 7 Polymer product analysis/characterization additive analysis, see also Additives, 9 contaminant analysis, see Failure analysis crystallinity, crystallization, 8, 70–74 defect analysis, see Failure analysis degradation, see Degradation fracture, see Failure analysis, 679 molecular Orientation, see Orientation network, see Network spatial heterogeneity, 9 stability, 453 surface analysis, 9, 675–682 Polymer, blend(s), 52, 53, 57, 66, 81, 111, 112, 114, 117, 140, 232, 279, 426, 538, 555 chemistry, 14–62 copolymer acrylonitrile/butadiene/styrene, ABS, 66, 436 ester copolymers, 720–721 ethylene/a-olefin, 260, 264, 270, 275 ethylene/vinyl acetate, 413, 419, 441 ethylene/propylene/diene, EPDM 75 styrene/acrylonitrile, SAN, 66 styrene/butadiene, SBR, 75 vinylidene difluoride/perfluoropropylene, (Vitons), 76 natural, cellulose, 16, 484 polyisoprene, 29, 479 pullulan, 490 networks, 338–376 thermoplastic conjugated polymers, 711–712, 714–715N poly(acetylene), 711
Neoprenes (2-chlorobutadiene polymer), 76 nylon(s), 16, 32, 66, 172, 660, 721 nylon 6 (polyamide 6), 108, 427 nylon 66 (polyamide 66), 16, 72, 74, 108, 406, 427, 632 organosiloxanes, 726–727 polyacrylonitrile, PAN, 78, 698, 706 polyacrylate(s), 66 poly(aminoborane), 702–703 polyamides, 721, see also nylon above poly(aniline), PANI, 416, 728–729 poly(ether imide), PEI, 74, 109 poly(aryl ether ether ketone), PEEK, 74, 85, 86, 434, 435, 718 poly(aryl ether ketone), PEK, 86, 718 poly(aryl ether sulfone), PES, 71, 74, 86, 173–174 polybutadiene, 487 polybutene, 22 poly(butylenes(s) terephthalate), PBT, 60, 273 polycarbonate(s), 66, 74, 419, 423, 426, 713 polyester(s), 66 poly(ethers), 709–710 poly(ethylene adipate), 277 polyethylene, PE, 16, 17, 22, 23, 27, 32, 39, 46, 49 139, 143, 153, 278, 394, 472, 473, 475, 696, 697, see also Polyethylene above poly(diethyl siloxane), PDES, 366–367 poly(2,6-dimethyl-1,4-phenylene oxide), 470 poly(dimethyl 5-(4hydroxy butoxy isopththalate), 165 poly(dimethyl siloxane), PDMS, 140, 341, 343, 352, 353, 354, 362–364 poly(ethylene oxide), (PEO), 725–726 poly(ethylene terephthalate), PET, 16, 32, 72, 78, 183–194, 392, 472 poly(hexamethylene adipamide), see Nylon 66 poly(hydroxyl butyrate), 126 polyisobutylene, 33, 43 polyisoprene, 466 poly(methyl methacrylate), PMMA, 16, 59, 135, 137, 175–183, 404, 405, 434–435, 698–700 poly(methyl-phenyl silane), 30 polyoelfins, 45, 49 polyoxymethylene(s), POM, 66, 391, 439 poly(phenylene oxide), PPO, 66, 71 poly(phenylene sulphide), PPS, 74
Subject Index
poly(p-phenylene terephthalamide), (Kevlars), 32, 66, 86 poly(3-phenyl-1-ureidonitrile), PUN, 700 polyphosphazenes, 367 polypropylene, PP, 16, 17, 23, 30, 32, 33, 39, 41, 46, 70, 138, 259, 274, 281, 282, 392, 410, 442, 462, 472, 469, 473, 479, 481, 484, 518, 677, 697 poly(propylene glycol), PPG, 194–201 poly(pyridine), 710 polystyrene, PS, 16, 17, 36, 44, 70, 71, 130, 395, 472 poly(tetrafluoroethylene), PTFE, 33, 66, 70 poly(thiophene(s)), 701, 724 poly(urethane(s)) 67, 430 poly(vinyl acetate), PVA, 19, 82, 717 poly(vinyl chloride), PVC, 16, 17, 137–137, 416, 452 poly(vinyl pyrrolidine), PVP, 472 thermoset, epoxy resin, 17 phenol-formaldehyde resin, 17 urea/melamine formaldehyde resin, 17 unsaturated polyester, 17 Polymeric materials, 66 Polymerisation chain (addition), 34, 67 ionic, 42–45, 83, 194–201 radical, 35–41, 172, 175–182 metallocene-catalysed, 47–48, 153, 159–160, 161 Phillips process, 45–46 step (polycondensation), 34, 53–54, 55–56, 60, 66–67, 182–193 vinyl, 66 Ziegler-Natta process, 46–47, 76, 161 Positron annihilation lifetime spectroscopy, PALS, see Techniques and Tests Prepreg, 85 Processing, 68–87 Pulse-propagation, see Techniques and Tests Pyrolysis, Py, see Techniques and Tests Quantum mechanics, see Molecular modelling Raman spectroscopy, see Techniques and Tests Raman-microscopy, see Techniques and Tests Residual solvents, 599 Resins, 82–84
751
Resonance ionization spectroscopy, RIS, see Techniques and Tests Rheology, see Techniques and Tests RIS, see Resonance ionization spectroscopy; Techniques and Tests SALLS, see Small-angle laser light scattering; Techniques and Tests SANS, see Small-angle neutron scattering; Techniques and Tests SAXS, see Small-angle X-ray scattering; Techniques and Tests Scanning electron microscopy, SEM, see Techniques and Tests Scanning near-field optical microscopy, SNOM, see Techniques and Tests Scanning tunneling microscopy, STM, see Techniques and Tests SEC, see Size exclusion chromatography; Techniques and Tests Secondary ion mass spectrometry, SIMS, see Techniques and Tests SEM, see Scanning electron microscopy; Techniques and Tests Semi-empirical methods, see Molecular modelling Sequence, 7, 24–25, 715, see also Copolymers(s), sequencing Sheets. 79–81 SIMS, see Secondary ion mass spectrometry; Techniques and Tests Size exclusion chromatography, SEC, see Techniques and Tests Small-angle laser light scattering, SALLS, see Techniques and Tests Small-angle neutron scattering, SANS, see Techniques and Tests Small-angle X-ray scattering, SAXS, see Techniques and Tests s-NMR, see Solid-state nuclear magnetic resonance spectroscopy; Techniques and Tests SNOM, see Scanning near-field optical microscopy; Techniques and Tests Solid-state density functional methods, see Molecular modelling Solid-state nuclear magnetic resonance spectroscopy, s-NMR, see Techniques and Tests Spatial heterogeneity, 9, 527–557, 676–677 Spatial imaging, see spatial heterogeneity Spherulite, 21, 274–275, 281 Stabilizers, 457–458, 459 483–487 Staining, see Techniques and Tests
752
Subject Index
Stereoregularity, 7, 134–139, 478 STM, see Scanning tunneling microscopy; Techniques and Tests Supermolecualr morphology, 274–286 Surface(s), 679 surface analysis, 9, 675–682 surface coatings, 81–84 Swelling, see also Techniques and Tests, 356–358 Syndiotactic, see Tacticity Tacticity, 7, 29–30, 46, 135–139, 698 TDFRS, see Thermal diffusion forced Rayleigh scattering; Techniques and Tests Techniques and Tests atomic absorption spectrometry, AAS, 9, 563–565 atomic force microscopy, AFM, 8, 99, 275, 374–347, 410 Auger spectroscopy, 703–712 birefringence, 8, 301–305, 374, see also Orientation Brillouin scattering, 8, 376 capillary electrophoresis, 7 carbonyl index, 8, 394–397, 410, see also Degradation chemical titration, see Techniques and Tests, Titration chemiluminescence, CL, 8, 463–496 density, 8, 260–261 dielectric relaxation, 272–273 differential photocalorimetry, DPC, 8 differential scanning calorimetry, DSC, 8–9, 476–478, 490, 565, 618, 619, 652, 721 dynamic light scattering, 210, 225–227, 243–244 energy dispersive analysis/spectroscopy, EDA/EDS, 9 electron spectroscopy for chemical analysis, ESCA, 9, 555, 676, 681, 682, see also XPS electron spin resonance spectroscopy, ESR, 8, 500–521, 727–729 nitroxide radicals, 507, 518 spin trapping, 507, 516–517 electron spin resonance imaging, ESRI, 8–9, 510–-521, 552–554 electrophoresis, 240–241 evolved gas analysis, EGA, 8, 389 EGA-IR, 8 field-flow fractionation, FFF, 207, 232–235
fluorescence spectroscopy, 8, 322–325, 418–422 gas chromatography, GC, 8–9, 422, 565–567 GC-IR, 8 GC-MS, 9, 422, 565–567, 624 gel permeation chromatography, 7–9, 141, 490, 617, 673, 741, see also Size exclusion chromatography, SEC GPC-IR, 8 GPC-MS, 8, 565 gelation, 8 gel-point determination, 7 high performance liquid chromatography, HPLC, 7 high throughput analysis, HTA, 735 inductively coupled plasma atomic emission spectroscopy, ICP-AES, 9, 571 inductively coupled plasma mass spectrometry, ICP-MS, 9, 622 infrared spectroscopy, IR, 7–9, 207, 240, 262, 305, 374, 402, 693 attenuated total reflection, ATR, 9, 535–536, 541–542, 612–614, 617, 618, 629, 636, 640, 644, 646, 653, 657, 659, 660–663, 666–669, 678, 681, 740 carbonyl index, 8, 394–397, 410, see also Degradation FTIR-microscopy, see IR-microscopy below IR-microscopy, 8, 9, 411, 404, 534–540 mid-infrared spectroscopy, mid-IR, also Fourier transform infrared spectroscopy, FTIR, 7–9, 135, 172–174, 179, 185–188, 207, 262, 402–414, 567, 612, 624, 637, 740 near-infrared spectroscopy, NIR, 9, 550–551, 740, 742 near-infrared imaging, 9 specular reflection, 311–312 time-resolved, 312–313 iodometric test, 8, 397, 410 inverse gas chromatography, IGC, 8 laser enhanced ionization spectroscopy, LEIS, 9, 555–557 liquid chromatography, LC, 8, 207, 443–447 LC under critical conditions, LC-CC, 8 LC-IR, 8 LC-MS, 7–9, 570–571 light scattering, see also dynamic and static light scattering 7 magnetic resonance imaging, MRI, 9
Subject Index
mass spectrometry, MS, 7, 172–202, 207, 237–239, 422–429, 712–718, see also ICP-MS direct insertion probe pyrolysis mass spectrometry, DPMS, 426 electrospray ionization-MS, ESI-MS, 173 matrix-assisted laser desorption mass spectrometry, MALDI-MS, 7, matrix-assisted laser desorption time-offlight mass spectrometry, MALDI-TOF-MS, 8, 173–174, 207, 427, 429, 741 MS-MS and MSn 173 melt flow index, MFI, 8, 399–402 molecular modeling, see Molecular modelling molecular weight distribution methods, 207 dynamic light scattering, 207 field-flow fractionation, FFF, 7, 207 mass spectrometry, see MALDI-TOF-MS above membrane osmometry, 7, 207 sedimentation equilibrium, 207 sedimentation velocity, 207 size exclusion chromatography, SEC, see SEC below static light scattering, 207 Ubbelohde viscometer, 207 ultracentrifugation, 7, 207, 244 vapour phase osmometry, 207 near-infrared spectroscopy, NIR, see infrared spectroscopy above nuclear magnetic resonance spectroscopy, NMR, 7–9, 135, 139, 143, 145–147, 162, 164–165, 172–202, 207, 239–240, 266–267, 325–327, 375, 429–433, 629, 655, 722–724 Grant and Paul chemical shifts, 145–147 magnetic resonance imaging, MRI, 552–554 solid-state NMR, s-NMR, 8–9 optical microscopy, 8, 278, 610, 613, 649, 663–666 osmometry, see also molecular weight distribution methods above 207, 213–217 oxidative-induction time, OIT, 390–393, see also Differential scanning calorimetry, DSC, oxygen uptake, 8, 393–394 photoelectron spectroscopy, PES, 9, 555, 703–712 phosphorescence, 8 plasma emission spectroscopy, 571
753
positron annihilation lifetime spectroscopy, PALS, 269 pulse-propagation, 8 pyrolysis, Py, 412, 415, 416 Py-GC-IR, 8, 412 Py-GC-MS, 8, 422, 594 Py-IR, 8 Py-MS, 8, 422, 426 Raman spectroscopy, 7–9, 262–266, 284–286, 313, 414, 693, see also Longitudinal acoustic mode Raman-microscopy, 8, 9, 319, 529–534, 540, 542 resonance ionization spectroscopy, RIS, 9 rheology, 7, 147–150 scanning electron microscopy, SEM, 9, 538–540, 610, 611, 628–631, 637, 645, 647–648, 650, 657 , 663 SEM-EDA/EDS, 9, 571, 610, 630, 645 scanning near-field optical microscopy, SNOM, 9, 551–552 scanning tunneling microscopy, STM, 8, 374 secondary ion mass spectrometry, SIMS, 8–9 TOF-SIMS, 9, 552 size exclusion chromatography, SEC, 7–9, 139, 141–143, 207 SEC-HPLC, 7 SEC-IR, 7 SEC-MS, 7 small-angle laser light scattering, 8, 278 small-angle neutron scattering, SANS, 7, 8, 126, 131, 150–153, 375–376 small-angle X-ray scattering, SAXS, 7, 8, 150 solid-state nuclear magnetic resonance spectroscopy, s-NMR, 7, 8 staining, 8, 397–399, 408 static light scattering, 207, 220–224 swelling, 8 thermal analysis, TA, 8, 261–262, 436–442 thermal diffusion forced Rayleigh scattering, TDFRS, 7, 228, 244 thermogravimetric analysis, TGA, 8, 438–442, 572, 647, 652, 663, 670 TGA-IR, 8, 413 TGA-MS, 8, 439–440 titration, 7, 8, 185 transmission electron microscopy, TEM, 8 ultracentrifuge, see molecular weight distribution methods above uv spectroscopy, 396, 408, 418, 419 viscometry, 7, 207, 218–220, 672 visible spectroscopy, 8
754
Subject Index
wide-angle X-ray diffraction, WAXD, 8, 258, 328, 329 wide-angle X-ray scattering, WAXS, 8, 266, 270 X-ray diffraction, XRD, 258–260, 328–333, 718–722 X-ray fluorescence spectroscopy, 9, 573 m-XRF, 9, 554–555 X-ray photoelectron spectroscopy, XPS, 8–9, 409, 433, 555, 626, 703–712 Teflons 33, see also Polymer, Thermoplastic, Poly(tetrafluoroethylene) Telechelic, 68 TEM, see Transmission electron microscopy; Techniques and Tests Tg, see Glass transition temperature TGA, see Thermogravimetric analysis; Techniques and Tests Thermal analysis, see Techniques and Tests Thermal diffusion forced Rayleigh scattering, TDFRS, see Techniques and Tests Thermogravimetric analysis, TGA, see Techniques and Tests Thermoplastic, 17, 68–70 Thermoset, 17, 68–70 Tie-molecules, 21, 73, 75 Time-temperature-transformation, TTT , 24 Titration, see Chemical titration; Techniques and Tests 7, 8 Tramsdorff effect, 39–41 Transmission electron microscopy, TEM, see Techniques and Tests
Ultracentrifugation, see Techniques and Tests Unit cell, 19–20 Unsaturation, 7 UV spectroscopy, see Techniques and Tests Vapour pressure osmometery see Techniques and Tests Viscometry, see Techniques and Tests Visible spectroscopy, see Techniques and Tests Vitrification, 39–41 Vulcanisation, 57, 69, 75 WAXD, see Wide-angle X-ray diffraction; Techniques and Tests WAXS, see Wide-angle X-ray scattering; Techniques and Tests Wide-angle X-ray diffraction, WAXD, see Techniques and Tests Wide-angle X-ray scattering, WAXS, see Techniques and Tests XPS, see X-ray photoelectron spectroscopy; Techniques and Tests X-ray fluorescence spectroscopy, XRF, see Techniques and Tests X-ray photoelectron spectroscopy, XPS, see Techniques and Tests XRF, see X-ray fluorescence spectroscopy; Techniques and Tests Zimm plot, 223
: CH3 :C :H
Plate 1 Helical structure of isotactic polypropylene. (For Black and White version, see page 33.)
dmin
p R2
R1
a)
b)
Plate 2 (a) Branched chain aggregate, (b) Branched chain aggregate; decomposed into the minimum path, p, and the branches [83]. Reprinted with permission from Beaucage [83]. Copyright 2004, American Physical Society. (For Black and White version, see page 151.)
b L
σe
g a
i σ
Plate 3 Schematic representing the secondary nucleation process and growth at the crystal face by spreading. The rates of these two processes are i and g, respectively. (For Black and White version, see page 154.)
Intensity 1000
1100
1200
1300
1400
1500
1600
-1
Wavenumber (Δυ) cm
Plate 4 Raman spectra of orthorhombic ethylene 1-hexene copolymer with band fitting. The crystalline band at 1,416 cm1, and amorphous bands at 1,303 cm1 and 1,080 cm1 are used to compute the crystallinity content: ac ¼ 0.52, and the amorphous content: aa ¼ 0.42. (For Black and White version, see page 264.)
Tc = 148
178.4°C 168.8°C
171.0°
(a) Tc = 148C, 2days
(c) 171C, 80min
140
150
160 170 temp (°C)
180
(d) 171C, 200min
190
(b) 171C, 10min
(e) 171C, 300min
Plate 5 Isothermal melting of Ziegler–Natta isotactic poly(propylene). (a) Spherulites with mixed birefringence at Tc ¼ 1481C. The top middle figure displays the melting for the same thermal history. (b) Subsequent to crystallization, the temperature was raised to 1711C; spherulites acquire negative birefringence. (c), (d) and (e) Isothermal melting at 1711C for 80, 200 and 300 min, respectively. Reproduced with permission from W.T. Huang, Dissertation, Florida State University, 2005. (For Black and White version, see page 281.)
27750
150 100
Micron
27700
50 0
27650 27600 27550 27500 48550 48600 48650 48700 48750 48800 Micron
0.00
10 μm
3750 3500 3250 3000 2750 2500 2250 2000 1750 1500 1250 1000
Plate 6 FTIR transmission image of a PA/PTFE blend (left) and SEM image from the same area (right). PTFE distribution was calculated from the 1,210 cm1 C–F absorption (intensity: cf. color scale in the middle). The arrow indicates from where on the image the IR spectrum was extracted. The orange ovals show identical PTFE clusters as detected by FTIR and SEM, respectively. (For Black and White version, see page 539.)
34320
2[Micron]
34320
34300
34300
34200
34200
36580
36600
36620
36580
36600
36620
Plate 7 IR-ATR images of a PA/PTFE polymer blend; bright colors: PTFE clusters. Left: integration of 1,149 cm1 C–F absorption. Right: PCA factor plot — additional clusters appear within the white circles. (For Black and White version, see page 542.)
34320
34320
34300
34300
34280
34280
36580
36600
36620
36580
36600
36620
36580
36600
36620
34320
34300
0 1150 1200 1250 1300 1350 1400 1500 1550 1600
34280
(a)
(b)
Plate 8 (a) FTIR ATR image of silicone oil distribution in PA/PTFE blend. Top left: integration of 1,261 cm1 (Si–C) band (cf. IR spectrum of the blend shown below); top right: after PCA; bottom right: PTFE distribution (1,149 cm1). Bright color means high concentration. (b) SEM/EDXS elemental mapping of fluorine (red) and silicon (green) in a PA/PTFE/Silicone blend. Size of the image: 40 mm 40 mm. (For Black and White version, see page 543.)
10
0
10
0
-10
2
-2
-10
Raman images
-10
-2
0
2
before ESEM
10 0
after ESEM -10 -20 10
Plate 9 Raman (left) and ESEM (right, SE and BSE) images (for explanation see text). (For Black and White version, see page 545.)
Plate 10 Separation of the standard ‘‘Grob mix’’ using two-dimensional GC/MS. (For Black and White version, see page 566.)
Plate 11 Examination of the acetone extract from an EPDM (ethylene propylene diene monomer) rubber using two-dimensional gas chromatography. (For Black and White version, see page 568.)
Plate 12 Chromatogram from conventional SEC column compared to high-speed SEC column tested on an identical instrument with polystyrene standards in tetrahydrofuran (THF). (For Black and White version, see page 742.)
