This content was uploaded by our users and we assume good faith they have the permission to share this book. If you own the copyright to this book and it is wrongfully on our website, we offer a simple DMCA procedure to remove your content from our site. Start by pressing the button below!
and p is a chain-bending modulus. Within the limits of the simplifying assumptions made in the development of this diffusion model (45) the numerical factor 0 was found to be equal with 9.1 x lo4. One can assume that for a given penetrant polymer system E * , m* and p* are known or can be determined from appropriate experimental data reported in the literature. Further one can assume that AE has been estimated theoretically using this diffussion model. Then, by substituting these parameters into Eq. 5-4 one could in principle calculate a diffusion coefficient D. The problem is that both Eqs. (5-3 and 5-4) contain one parameter, namely the mean-square “jump” distance, h, which is generally not known or very difficult to determine experimentally. Thus, in order to calculate a D a “shrewd guess” is needed for h, based on similitudes with other penetrant polymer systems. In other words is not possible to use the formula for D given in the framework of this model to effectivelly predict the magnitude of D from “first principles”, i.e. thermodynamic, molecular and structural data on the penetrant polymer system. Moreover it was discussed in (50) that a correct solution of a key problem in the derivation of the statistical mechanical approach used in the Pace and Datyner model is possible only at 0 K. Adding this fact to the “shroud guessing” of h in order to produce (estimate) a diffusion coefficient largely impairs the usefulness of this model for the type of migration estimations which might be envisaged by a process engineer from the packaging sector, see Chapter 15.
c,
Modelsfor diffirsion in polymers
133
Free-volume models Among the popular methods for interpreting the diffusion of small penetrants in polymers are the so called “free-volume’’ models (6,11,13,51-54). The basic assumption of these models is that the mobility of both polymer segments and penetrant molecules is primarly determined by the available free-volume in the penetrant polymer system. The free-volume of the polymer is regarded as an “empty” volume between the chains of the polymer. Similarly the free-volume of the penetrant can be regarded as the volume not occupied between the molecules of the penetrant. Most free-volume models for diffusion in polymers follow the phenomenological basis set in (55) where the self-diffusion of an ideal liquid of hard spheres (“molecules”) has been analysed. These molecules are confined - for most of the time - in a “cage” formed by their immediate neighbours. A local fluctuation in density may open a “hole” within a cage, large enough to permit a considerable displacement of the sphere contained by it. This displacement gives rise to diffusion only if another sphere jumps into the “hole” before the first sphere returns to its initial position. Diffusion occurs not as a result of an activation process in the ordinary sense but rather as a result of the redistribution of the free-volume within the liquid of hard spheres. The model of diffusion of hard spheres is applicable to interpret self-diffusion in liquids which behave according to the van der Waals physical interaction model (56). This might be the case for simple dense fluids at high temperature, T >> T,, but it is an oversimplified model for the real diffusion of small organic penetrants in polymers. The functional relationships derived in the model of hard-spheres have been reinterpreted over course of the time, leading to a series of more sophisticated free-volume diffusion models. Some of these models are presented briefly below. An attempt to correlate experimental diffusion data with free-volume, for the system of organic vapors with polyvinyl acetate, has been made in (57). The experiments showed that in this system, for T > T,, the diffusion is Fickian and that the measured average diffusion coefficient steeply increases with the concentration, c,, of penetrant in the polymer. To quantify such a finding, an empirical relation has been proposed earlier (58): D+
= D,,,exp
(w c,)
(5-5)
where w is a parameter. To refine this approach it was proposed that the diffusion coefficient might be proportional to the frequency with which segments of polymer chains were able to undergo rotational jumps (57). The relationship between the diffusion coefficient and penetrant concentration, expressed as solvent volume fraction, v,, was derived in terms of a theory for polymer segmental mobility (59). Eventually a relation was obtained which allowed examination of the relationship between the intrinsic diffusion coefficient, D’, and v, (57). To calculate with this formula D’, some thermodynamic and free-volume parameters for the penetrant polymer system must be calculated from data given in the literature and two adjustable parameters must be determined by fitting the theoretical curves to experimental diffusion data (57). Once these data were known the formula for D’ showed an excellent fit over the concentration range which covered a 1000-fold increase of D+ (5357). Despite this positive result one can conlcude that the model has only a semi-predictive and correlative character and it would be quiet unpractical to use it for the type of diffusion coeffi-
134
Mercen
cient estimations currently of interest in the field of substance migration through and from polymeric packaging materials. One of the simplest early free-volume diffusion models was formulated in (51,52,60). The concept of this model was considered an advance, because some of the parameters required to describe the concentration dependence of the diffusion coefficient could be obtained from the physico-chemical properties of the polymer and penetrant. The relation proposed for the calculation of the thermodynamic diffusion coefficient, DT, was (51,60):
where Vf is the average fractional free-volume. The proportionality coefficient Ad is considered to be dependent primarily upon the size and shape of the penetrant, while Bd is a parameter which is independent of temperature and penetrant concentration. To work effectively with Eq. 5-6 the magnitude of its parameters must be determined. For this the free-volume of the penetrant poylmer system must be evaluated from viscosity data. Eventually the two adjustable parameters Ad and Bd must be calculated by fitting appropriate experimental diffusion data. For the diffusion of organic vapors in rubbery polymers, the correlation between theoretical curves and experimental data is often acceptable. In such cases the model can be used in a semi-predictive manner in order to estimate diffusion coefficients DT. beyond the penetrant concentration and/or temperature range where experimental results were collected. As already mentioned, the model includes in its formulae the adjustable coefficients Ad and Bd which cannot be determined from “first principles”. Hence, one cannot ascertain true predictive capabilities from the model and thus it is of little efective help for the practical diffusion coefficient estimations envisaged in this work. The free-volume model of Vrentas and Duda
In the last two decades Vrentas, Duda and their co-workers have published a substantial number of papers (61-67) on the free-volume model of diffusion in polymersolvent systems they developed in the late 70’s (68-72). This model, which is often cited and used in the literature, underwent a number of modifications over the years and appears to apply well to the diffusion of organic solvents in rubbery and glassy polymers. In order to develop a consistent free-volume diffusion model, there are some issues which must be addressed, namely: i) how the currently available free-volume for the diffusion process is defined, ii) how this free-volume is distributed among the polymer segments and the penetrant molecules and iii) how much energy is required for the redistribution of the free-volume. Any valid free-volume diffusion model addresses these issues both from the phenomenologic and quantitative points of view such that the diffusion process is described adequately down to the “microscopic” level. Vrentas and Duda stated that their free-volume model addresses these three issues in a more detailed form than previous diffusion models of the same type. Moreover, it was stated that the model allows the calculation of the absolute value of the diffusion coefficient and the activation energy of diffusion mainly from parameters which have physical significance, i.e. so-called “first principles”. In the framework of this model the derivation of the relation for the calculation of the self-diffusion coefficient of the sol-
vent Dls is not a trivial task. A relation can obtained which gives the dependence of Dls on the nature of the penetrant and its concentration in the polymer-solvent system, the temperature and on the molecular weight of the polymer. For a rubery polymer a condensed form of this relation, valid also for low penetrant concentration levels, can be cited from (63):
D,,
=Do
(
exp {-y
exp -RTE')
("'
w 5-+ v i s ) }
"FIi
(5-7)
For the definition of all parameters involved in the above relation see (62,63). The explicit form of Eq. (5-7) contains fifteen parameters of which thirteen can be determined from thermodynamic and molecular data of the penetrant and polymer. These parameters include: two specific hole-free volumes for the components, free-volume parameters for the penetrant and polymer, the thermal expansion coefficient of the polymer, free-volume overlap factors, glass transition temperatures, the fractional composition of the system, etc. For a non initiated reader, the procedures followed to determine these thirteen parameters are not quite simple, although the authors of the model state that the data needed for this purpose are generally available in the literature. In the scheme for the estimation of these parameters presented in (63) one can see that in order to perform calculations with the model, two parameters must be calculated by fitting the theoretical curves to experimental results obtained in the socalled "zero-penetrant" concentration limit. Thus, it is stated that using a non-linear regression analysis "...all of the parameters of the theory can be determined in general with as few as two diffusivity data points" (63). The results obtained with this complex but straightforward procedure have shown that the model provides excellent correlations for diffusivity data in several polymer-solvent systems Fig. 5-3. Having mentioned the correlative capabilities of this model, one can consider its semi-predictive abilities. It was mentioned that a number of diffusion data taken from a limited range of penetrant concentrations are required to calculate two of the parameters of the model. Once these parameters have been determined, one can make theoretical predictions for diffusion coefficients over a wider range of penetrant concentration or temperature variation. This is a critical test for any theoretical model,
0
0.2
0.4 W S
0.6
O8
Figure 5-3: Test of predictive capabilities of proposed free-volume model using data for the toluene polystyrene system. Only data points represented by solid symbols were used to obtain free-volume parameters (73).
136
Mercea
since an useful model should have at least an established semi-predictive capability. These results are encouraging evidence that the proposed model is a suitable tool for a more accurate description of the diffusion process in rubbery polymers. The model was most often tested by its authors for polymer-solvents systems like: polystyrene, polymethylacrylate, polyethylmethacrylate and polyvinylacetate; and for toluene, benzene, ethylbenzene as solvents. The experimental test conditions reported in (6170), especially for high concentration of solvent in the polymers, often differ considerably from what is generally of interest when these polymers are used in the packaging sector. Therefore, to assess the potential use of this free-volume diffusion model in the field of small substance migration in polymeric food packagings, the model must be tested for penetrant polymer systems which are specific for this field (see Chapter 9). Moreover it is to mention that, because the model contains two parameters which cannot be determined from “first principles” but only by fitting a limited amount of experimental data, one cannot ascribe true predictive capabilities to the model. To conclude this section, it may be interesting to mention what was concluded recently in (17) on the future of the free-volume diffusion models: ...“However, phenomenological transport models based on free-volume concepts are likely to become obsolete during the coming decade, due to the development of computational techniques of simulating polymer microstructures” .... The development of such techniques and their results are discussed in Section 5.2.
5.1.2 Diffusion in glassy polymers As already mentioned at the beginning of this section, the diffusion of small penetrants in glassy polymers is a much more complex process than that in rubbery polymers. This is due, at least in part, to the fact that free rotation of the polymer chains is restricted below T,. Thus, it was assumed that fixed microcavities or “holes” of various sizes result throughout the matrix of the polymer below T,. These “holes” are “frozen” into the polymer as it is quenched from the rubbery state (74). The concept that two mechanisms of sorption may be implicated in the diffusion and behaviour of small penetrants in amorphous glassy polymers was first suggested in (75). Here, and later in (76) it was speculated that below T, the “holes” may act to immobilize a portion of the penetrant molecules by binding them at high energy sites at the periphery of the “holes” or by entrapment in the “holes”. Based on this concept it has been suggested (77) that the sorption of organic vapors in a glassy polymer is due to two concurrent mechanisms: (i) ordinary dissolution in the matrix of the polymer (so called Henry’s law sorption) and (ii) a ‘‘hole’’-filling process obeying Langmuir’s law. This phenomenological model was accompanied, for the sorption of simple gases and organic vapors, by the equation (77): C=k,p+
a1 P
1
+
bp
(5-8)
where a], b and kD are adjustable coefficients and p is t h e pressure of the gaseous penetrant. It has been reasoned that al and b are given approximately by the statistical thermodynamic treatment of Langmuir’s isotherm (78) and kD by the lattice theory of penetrant polymer solutions (79). Later it was postulated that in Eq. (5-8) one
Models for difiiision in polymers
137
may equate a l = c‘Hb and designate b and c ’ ~as “hole affinity” and “hole saturation” constants respectively (80). This quantitative description of the solution of a simple penetrant in a glassy polymer is known today as the Dual Sorption Theory (with total immobilization), (DST). The problem is that the basic assumptions of DST cannot be justified “a priori” (9). The possibility that penetrant molecules adsorbed in “holes” may not be completely immobilized is one of these problems and has been addressed (81,82). If that is the case, both the normally dissolved penetrant molecules (according to Henry’s law) and the partialy immobilized ones could diffuse through the matrix of the polymer and contribute to the diffusional flux. Moreover, in order to better describe real systems, another key postulate from the initial DST should be relaxed, namely that the normally dissolved species and those adsorbed into the “holes” are always in local equlibrium (82). That means the diffusion model should incorporate some kinetics for the immobilzation process. There will be cases where the diffusion and immobilization proceed at comparable rates; and limiting cases, where one of the two processes predominates. The phenomenological sorption theory which resulted from taking account of these assumptions is known as Dual Sorption (with partial immobilization) Theory. Because of the assumed dual sorption mechanism present in glassy polymers, the explicit form of the time dependent diffusion equation in these polymers is much more complex than that for rubbery polymers (82-86). As a result exact analytical solutions for this equation can be found only in limiting cases (84,85,87). In all other cases numerical methods must be used to correlate the experimental results with theoretical estimates. Often the numerical procedures require a set of starting values for the parameters of the model. Usually these values are “shroud guessed” in a range where they are expected to lie for the particular penetrant polymer system. Starting from this set of arbitrary parameters, the numerical procedure adjusts the values until the best fit with the experimental data is obtained. The problem which may arise in such a procedure (88), is that the numerical procedures may lead to excellent fits with the experimental data for quite different starting sets of parameters. Of course the physical interpretation of such a result is difficult. However, the mathematical formulae of DST satisfactorily present the dependence of the solubility and diffusion coefficients for simple gases and organic vapors on the concentration of the penetrant in the glassy polymer (9,11,13,15,17,33,34,89). From the point of view of earlier discussions, namely the true prediction of diffusion coefficients for volatile and nonvolatile organic penetrants in glassy polymers, the diffusion equations derived in the framework of the DST have only a limited usefulness. That means that, because the parameters of the DST models are not directly related to “first principles”, the equations can be used with success to correlate experimental results, but not to truly predict diffusion coefficients. One possible solution to this problem is to develop “microscopic” diffusion models for glassy polymers, similar to those already presented for rubbery polymers. Ref. (90) combines some of the results obtained with the statistical model of penetrant diffusion in rubbery polymers, presented in the first part of Section 5.1.1, with simple statistical mechanical arguments to devise a model for sorption of simple penetrants into glassy polymers. This new statistical model is claimed to be applicable at temperatures both above and below T,. The model encompasses dual sorption modes for the glassy polymer and it has been assumed that “hole”-filling is an important sorption mode above as well as below T,. The sites of the “holes” are assumed to be fixed within the matrix
138
Mercea
of the polymer. Starting from these assumptions and using elementary statistical mechanical arguments, the authors of the model estimated the values of parameters approximately, which were then included in relation to the solubility coefficient (90). For a series of simple gases diffusing in some glassy polymers, solubilty data calculated with the model were compared with experimental sorption data. Semiquantitative to qualitative agreements between theory and experiment were found. Unfortunately, for the scope of the present book, the model was not developed for estimating of diffusion coefficients in glassy polymers. Local density fluctuations occur in penetrant polymer systems both above and below T,. It is then reasonable to expect that a free-volume diffusion model should also provide an adequate description of the diffusion of small penetrants in glassy polymers. To reach this goal the free-volume model for diffusion of small penetrants in rubbery polymers, second part of Section 5.1.1, was modified to include transport below T, (64,65,72,91-93). In principle the diffusion process in a penetrant polymer system can be characterized by determining the mutual diffusion coefficient and its dependence on temperature, penetrant concentration, pressure and polymer molecular weight. When molecular relaxation in the polymer-solvent system is much faster than the diffusive transport, the conformational changes in the polymer structures appear to take place instantaneously. The diffusional transport is comparable in such cases to the transport observed in simple liquids. This type of transport mechanism is considered to characterize quite well polymer solvent systems for T > T,. As the temperature decreases towards T, the probability that a local fluctuation in density will produce a “hole” of sufficient size so that a polymer jumping unit or a penetrant molecule can move in decreases. When T < T, the “hole-free’’ volume which can be rebistributed with no energy change in the penetrant-polymer system becomes very small. Below T, the motions of the polymer are so hindered that, for a given penetrant concentration, significant movements do not occur at the time scale of the diffusion experiment. Moreover at a very low penetrant mass fraction, the structure of the glassy polymer is essentially unaffected by the presence of the penetrant and the diffusion process is Fickian (61,72,92). The diffusion process under such conditions has been denoted as an elastic diffusion process (61,71) which can be analysed using the classical theory of diffusion. In the limit of zero penetrant mass fraction these phenomenological assumptions were included into the relations of a mathematical formalism which led eventually to an expression for the dependence of the mutual diffusivity on temperature (72):
where the parameter 9+ describes the character of the change of the volume contraction which can be attributed to the glass transition. For glassy polymers, T < Tg2,the temperature dependence of D at zero penetrant concentration can be described by an apparent activation energy for diffusion, Ed, (72,93): (5-10)
Modelsfor diffiisron in pol.yniers
139
The temperature dependence of D for the n-pentane-polystyrene system both above and below Tg2 has been calculated using the formulae of this free-volume model (64). The results obtained are shown in Fig. 5-4 along with a few experimental data (94) for the same system at three temperatures below Tg2. Similarly to Fig. 5-4 for other glassy polymer-solvent systems also the predictions of this free-volume theory are in general agreement with experimental data on t h e temperature dependence of D in the vicinity of Tg2.,In particular, the theory predicts a step change in Ed at TR2,and this is consistent with most experimental investigations of polymer-solvent diffusion at temperatures just above and below the glass transition temperature (6,11J5). Vrentas, Duda and their co-workers refined in recent years their free-volume model for diffusion in glassy polymers to address also the problem of Fickian diffusion at finite solvent concentrations (64,65,92). For this the free-volume and thermodynamical parameters involved in Eq. (5-7).which gives the solvent self-diffusion coeffcient D,, in a rubbery polymer, were adapted to describe adequately the phenomenology of diffusion below the glass transition temperature,T,,,, of the polymer-solvent mixture at a particular solvent mass fraction. A series of assumptions on the structure, properties and sample history and the introduction of an additional expansion coefficient were necessary (65) to express the behavior of the free-volume parameters below Tgm.Eventually a set of equations was obtained and it was stated that using them "... calculation of D,, for glassy polymers is no more difficult that computing D,, for rubbery polymer-solvent systems" (65). However it was emphasized that the predictions of the model are sensitive to the sample preparation history. that means reasonably good agreement between theory and experiment will be obtained only for sample preparation histories which are similar to the one used in the model. Anyway one can see that up to nineteen parameters are needed to express, with this free-volume model, the concentration and temperature dependence of D1, in a glassy polymer (65,92). It is stated in these publications that all these parameters except two can de estimated from physico-chemical data generally available in the literature. To determine the remaining parameters a small amount of experimental diffusion data is needed.
-7
A
v)
\
N
E
-9
0
n
-D -11 -12
2.0
2.5
I/T . 1 0 3
3.0 ( ~ - 1 )
FigureS-4: Comparison of predictions with experiment for the n-pentane-polystyrene system (64.94).
140
Mercea
The reasonably good agreement between theory and experiment shown by this free-volume model (65) recommends it as an interesting tool to model the diffusion in glassy polymers used in the packaging sector. However, the problem is that the correlative, semi-predictive and predictive capabilities of this model do not address exactly the type of diffusion coefficient prediction which is of interest for the estimation of many migration processes in polymeric packagings. When we state this we are thinking not only on how difficult it would be to specify all the parameters of the model for a complex penetrant like an antioxidant or stabilizer but even more if the model is still valid for this type of polymer penetrant systems. The above sections have presented models that link the process of diffusion of small penetrants in polymers to “microscopic” features of the penetrant polymer system. Strictly speaking the type of diffusion models presented above are not truly “microscopic” because they actually describe average and not truly local - “microscopic” - properties of the penetrant polymer system. Sometimes even excellent correlations of experimental data offered by these models are due to the fact that the experimental methods used to determine the diffusion coefficients are in turn probing the penetrant polymer system over %on-microscopic” distances and comparatively long times. Somewhat closer to the designation of a “microscopic” model are those diffusion theories which model the transport processes by stochastic rate equations. In the most simple of these models an unique transition rate of penetrant molecules between smaller “cells” of the same energy is determined as function of gross thermodynamic properties and molecular structure characteristics of the penetrant polymer system. Unfortunately, until now the diffusion models developed on this basis also require a number of adjustable parameters without precise physical meaning. Moreover, the problem of these later models is that in order to predict the absolute value of the diffusion coefficient at least a most probable “average length” of the elementary diffusion jump must be known. But in the framework of this type of “microscopic” model, it is not possible to determine this parameter from “first principles”. To conclude one can state that in the framework of the “classical” diffusion models more or less complex mathematical formulae have been developed with the aim of interpreting experimental data and even offering an insight on the mechanics of diffusion. The mathematical relations for the diffusion coefficient rely on parameters which must be determined from given physico-chemical and structural data about the penetrant polymer system. But, almost without exception, these models also include a number of adjustable parameters which can be determined only by fitting experimental data to theoretical curves. In some models the physical meaning of these adjustable parameters is quite unsubstantiated. Moreover, among the earlier “classical” diffusion models some “shrewd guessing” of some model parameters is needed. Therefore one can state that the main limitation of all these phenomenological models is that they cannot truly predict diffusion coefficients only from “first principles”.
Models for rliffiision in polymers
141
5.2 Diffusion in polymers - The computational approach It was shown in the above section that as a rule, at the base of the “classical” or “microscopic” diffusion models, there are ad hoc (heuristic) assumptions on a certain molecular behaviour of the polymer penetrant system. The fact that the mathematical formulae developed on such bases often lead to excellent correlations and even semipredictions of diffusion coefficients must be aknowledged. It is true that the “classical” models are not capable to predict diffusion coefficients only from “first principles” but this is often not an obstacle to hinder their use in certain types of investigations. Therefore we are quiet sure that this type of diffusion models will certainly be used in the future too for the interpretation of diffusion experiments. The problem of diffusion modeling in polymers changes to some degree when one envisages to develop a really atomistic model, with trully predictive capabilities and without making any ad hoc assumption on the molecular behaviour and/or motions in the polymer penetrant system. In principle, a possibility to develop such diffusion modelings, is to simulate theoretically the process of penetrant diffusion in a polymer matrix by computer calculations. For this one starts by considering only an appropriate set of “first principles” which describe at a trully atomistic level the polymer and the penetrant. Then, these data about the atoms and molecules of the polymer are used to generate, by some means, a polymeric structure that has the “microscopic” and “macroscopic” properties of the true polymer, i.e. a low energetic state, an appropriate distribution of torsional angles, a physically acceptable distribution of unoccupied volume, density, and so on (95-99). Once this structure is generated a number of penetrant molecules are randomly “inserted” in it (where enough unoccupied volume is available). Then, the sytem is left to pursue its “molecular dynamics”, i.e. the atoms and molecules of the system are allowed to move in the force fields and under the interactions acting inside the system over a certain time interval. During this process there is no interference from the outside and, in particular, no heuristic assumptions are made about the molecular motions. If the process is simulated consistently enough time, by observing for example the average displacement of the penetrant species, one can eventually calculate their diffusion coefficient (98). Though, this scheme sounds very elegant and attractive its practical achievement is a complex and demanding task. Because of that computer simulation, as a method for the estimation of the diffusion coefficients in polymers, has only lately become a practicable approach. The prerequisites which make possible the development of “atomistic” simulations of diffusion in polymers are the development of powerful methods for the simulation of polymer microstructures and dynamics and also great computation capabilities of supercomputers. The first attempts in the direction of simulating theoretically at an atomistic level the diffusion of simple gas molecules in a polymer matrix were made more than two decades ago (100). But, the systematic development of “ab initio” computer simulations of penetrant diffusion in polymeric systems dates only from the late 80’s (101104). At the beginning of the 90’s it was achieved to simulate some qualitative aspects such as the diffusion mechanism, temperature, and pressure dependence of diffusion coefficients (105-109). The polymers chosen for investigation mainly fell into two categories: either they were easily described (model elastomers or polyethylene) or they were known to have, for simple permanent gases like H2, 02,N2, H20 or CH4,
142
Mercea
large diffusion coefficients (polydimethylsiloxane (PDMS) (11CL112) and atactic polypropylene (aPP) (113) ). The advantage of simulating at room temperature. for example the diffusive motion of H2 in aPP (D about lo4 cm2/s), is that the diffusive motion of the hydrogen molecules can already be sampled in relatively short simulations (about 0,5 ns (113) ). Based on these encouraging achievements, in the last five or six years, the interest of the researchers shifted from easy-to-compute polymer penetrant systems to those which have interesting technological potentials in such fields as: gas barriers (114117), gas or liquid separation processes (1 18-121), molded objects (packagings for example) (122) or swelling of polymers by solvents (123-126). Trying to model, theoretically, the transport of small penetrants in polymer matrices, one realizes that the characteristic length and time scales vary greatly and depend on the polymer morphology (98). Most of the polymers used technologically are either amorphous or partially crystalline. From experimental results obtained over the past four decades it is commonly assumed that both diffusion and sorption in crystalline polymers are orders of magnitude smaller than in amorphous ones (11,13,16,17,29,30). These facts determine that different theoretical and computational techniques will be appropriate for modeling the diffusion in different polymer penetrant systems (98). For the diffusion of small penetrants, i.e. simple gases and vapors of water and/or simple organic substances, in purely amorphous polymers the computational techniques of choice will be molecular dynamics, MD, (97-99, 127129) or the transition-state approach, TSA, (115,130-132). In a semicrystalline polymer a similar task can be approached for example by a Monte-Carlo 2-phase model (133). So far, the “atomistic” modeling of diffusion of small penetrants in polymers was predominantly done for amorphous polymers and using the MD or TSA techniques, which will be presented briefly in the next sections.
5.2.1 Molecular dynamics Because time is explicitly present in the formulations of MD, this technique is the most straightforward way of computer simulating the motion of penetrant molecules in amorphous polymer matrices (97-99). The MD method allows one to look at a truly “atomistic” level within the system as it evolves in time. Recently, excellent reviews on the use of MD for simulating penetrant diffusion in polymers have been published (96-99). A summary of the basic concepts and some relevant results obtained so far with MD will be presented bellow. To start a MD simulation of a diffusional process an amorphous polymer structure of the host material must first be theoretically generated. This structure must be low in energy and have the known physical properties of the polymer; chain length and distribution of torsional angles of polymer chains, density, distribution of free volume, etc. The origins of the MD approach to the problem of generating polymer structures lies in works done in the late 70’s to investigate theoretically amorphous bulk polymers (134-138). A MD approach to the problem of modeling the structure of amorphous polymers was introduced in (139) and a few years later developed in (140,141) to allow a detailed description of such systems. An overview of the various MD methods used to generate amorphous polymer structures can be found in (142). The principal methods are: (i) structural generation methods which in an ideal case are used to
Models for diffiision in polymers
143
generate a structure which needs no further refinement, (ii) structural refinement methods that ideally are so efficient that the starting structure can be arbitrary and (iii) coarse-graining methods in which the atomistic model of a polymer is mapped into a coarse representation of several atoms or even monomers. To generate a polymer structure theoretically its matrix is presented as an ensemble of microscopic structures which satisfy the requirements of detailed mechanical equilibria (140). For every atom its initial position and velocity have to be specified. Chain bond lengths and bond angles are fixed. Molecular movements are allowed to occur exclusively through rotations around the skeletal bonds of macromolecules. A polymer chain meeting these assumptions is built in vacuum by an iterative process that is started from an initially guessed “parent” structure which is then relaxed to a state of minimum potential energy (140). The density of the structure obtained must eventually equal that of the simulated polymer. The free-volume in the polymer can be estimated from the generated structure. To obtain a statistical average of this free-volume, a number of structures are generated starting from different “parent” chain configurations. Once the host structure was generated the next step in the MD simulation of diffusion is to “place” (insert) the diffusant molecules into the computed structure. The condition for inserting the penetrant molecules into the structure is to find “freevolumes” where the energy is below a certain threshold and that any two of the penetrant molecules are separated by some minimum distance. Then the penetrant and polymer molecules are allowed to interact with each other and move within the limits of the constrains they are subjected to. The straightforward technique is now to follow by computer simulation the displacement of the penetrants into the potential field of the system and eventually to estimate the mean-square displacement (MSD) of the penetrant species. Among the first remarcable results of MD simulations was the finding that diffusion of small molecules in amorphous polymeric structures proceeds by “hopping” (jumping) motions (106). From a phenomenologic point of view this is not a new result if one takes into account that such a mechanism was intuitively assumed in some “microscopic” diffusion models long before the development of computer simulation techniques, see the preceeding section. The new aspect is that the computational approach has led to this picture of the diffusion mechanism starting from true “first principles” of the penetrant polymer system and not on the basis of “shrewd guesses”. To illustrate this type of motion in Figure 5-5 a typical trajectory of a water molecule through an amorphous elastomer (PDMS) is presented (119,120). From Fig. 5-5 one can clearly discern that the voids forming the free volume of the rubbery polymer are clearly separated from each other and that there are two types of motion of the penetrant molecule: - for a relatively long period of time (typically a few 100 ps) the penetrant molecule stays confined in certain small regions of space, the “cavities” of the polymer matrix. The molecule explores the cavity thoroughly without being able to move beyond the confines of the volume it resides in. Thereby the penetrant is reflected by the polymer matrix about every few picoseconds (98,119,120); - the quasi-stationary period is interrupted by quick leaps from one such cavity to another close by. The jump between the two neighboring cavities is preceeded by the formation of a channel between them. Under favourable circumstances (right momentum) the penetrant then slips through this opening, essentially without activation energy or more exactly surpassing a small energy barrier, due to the fact that
144
Mercea Jump between cavities
I
Movements in
ca76
Figure5-5: A typical trace of the center of mass of one representative water molecule in a PDMS matrix (120).
the channels are on average narrow (98). The jump duration is short compared to the residence time in the cavities. A “hopping” event in a polymer matrix, as found typically in MD simulations is presented in Fig. 5-6 (106). As announced above these findings are in astonishing agreement with the “heuristic” pictures of the diffusion mechanism discussed in the framework of some “microscopic” diffusion models. But, besides being free of the conceptual drawbacks (the ad hoc assumptions) of the “classical” diffusion models, the MD method of computer simulation of diffusion in polymers makes it possible to get an even closer look at the diffusion mechanism and explain from a true atomistic level well known experimental findings. For example the results reported in (119,120) on the “hopping” mechanism reveal the following additional features. In a rubbery polymer with flexible macromolecular chains (PDMS for example) the cavities forming the free-volume are clearly separated from each other. The detailed evaluation of the movement of a penetrant particle from cavity (1) to the neighboring (2), did not show any immediate back jumps (2) + (1). This is mainly do to the fact that the channel between (1) and (2) closes quiet quickly. In a polymer with stiff chains (glassy polyimide (PI) for example) the individual cavities are closer to each other and a rather large number of immediate back jumps ocurred during the time interval simulated (120). This indicates that once a channel between two adjacent cavities in a stiff chain polymer is formed it will stay open for some 100 ps. This makes the back jump (2) -+ (1) of the penetrant more probable than a jump to any other adjacent hole (3). This process seems to be one cause for the general tendency that the diffusion coefficient of small penetrants in stiff chain glassy polymers is smaller than in flexible chain rubbery polymers. The results of MD simulations will be useful if they are able to reproduce with sufficient accuracy diffusion coefficients measured experimentally. Given the scatter between the results of different experiments reported in the literature, a computational method can be considered accurate enough if, for absolute diffusion coefficients, it reproduces the experimental values within one order of magnitude. Such results are presented in Table 5-1.
145
Models for difliision in po1ymer.s
t=6.0 PS
t=11.1 ps
k10.1 ps
(9
-
-
5A
t=12.1 ps
-
5A
t=l2.9PS
t=12.5ps
5A
t=13.3PS
I
\
t=13.7PS
t=14.1 ps
\
Penetrant molecule 5A )-------I
t=l6.1 PS Figure 5-6: Molecular dynamics simulation of a "jump" of an 0
2
molecule (106)
146
Mercea
Table 5-1: Diffusion coefficients calculated by molecular dynamic simulation and from experiment,
Polymer Polydimethylsiloxane
He
180.0 (300)
144
100.0 (300)
145
144
20.6 (300)
146
Pol ydimethylsiloxane
CH4
21.0 (300)
Polydimethylsiloxane Polydimethylsiloxane
H2O
15.3 (300)
112
14.5 (298)
147
EtOH
2.0 (300)
112
4.5 (298)
147
Polydimethylsiloxane Polydimethylsiloxane
H2O EtOH
20.0 (300)
1 I9
14.5 (298)
147
4.4 (300)
119
4.5 (298)
147
Polyisobutylene
He
30.0 (300)
148
5.96 (300)
151
Polyisobutylene
Hz
9.0 (300)
148
1.52 (300)
151
Polyisobutylcne
0 2
0.169 (300)
149
0.081 (300)
151
Polyisobutylene
CH4
0.63 (350)
150
1.7 (375)
152
Polyethylene
CH4
1.12 (300)
150
0.54 (296)
155
Polyethylene
CH4
1.6 (300)
112
0.54 (296)
155
Polyethylene Polyethylene
H20
7.8 (300)
150
4.4 (296)
155
0.7 ( 3 0 )
112
0.15 (296)
155
atactic Polypropylene
H2
44.0 (300)
154
-4.9'** (296)
155
atactic Polypropylene
0 2
4.0 (300)
154
-0.95'** (296) 155
atacticPolypropylene
CHJ
0.48 (300)
154
-0.24'** (296)
Pol yamidimide
HZ
0.97 (300)
143
1.3 (300)
156
Polyimide
N2
0.28 (300)
143
0.52 (300)
156
0.74 (300)
150
2.69 (300)
156
EtOH
Polyimide 0 2 Poly[ 1-(trimethylsily1)-I-Propyne] He
465 (300)
155
121
316 ( 3 0 K )
157
121
30.0 (303)
147
Poly[1-(trimethylsilyl)-1-Propyne] Oz
23.8 (300)
Poly[1-(trimethy1silyl)-1-Propyne] N2
20.5 (300)
121
36.0 (298)
158
Poly[ 1-(trimethy1silyl)-1-Propyne] CH4
16.7 (300)
121
22.0 (303)
147
Poly[l-(trimethylsilyl)-1-Propyne] CO'
4.0 (300)
121
19.5 (303)
147
Polyethylenetherephthalate Polvstvrene
CH4 CHI
-0.0063"
(333)
-0.056" (3251
117
0.0031 (333)
80
116
0.0338 (323)
159
(* diffusion coefficient extrapolated from higher temperatures) (** diffusion coefficient estimated from data for semicrystalline PP)
The results given in Table 5-1 show that the agreement between the diffusion coefficients predicted from MD simulations and experimental ones ranges from reasonable to excellent. At temperatures around 300 K this is found both for polymers which are above their glass transition temperature, T,, (PDMS, PIB, PE and aPP) and for polymers which are below T, (PET, PS, PTMSP, PI and PAI). As a trend one can notice, and this not only from Tab. 5-1 but also from other works published in the last six or seven years, that the agreement between MD simulations of diffusion and solvation of small penetrants in polymers and experiment steadily improved. These are encouraging developments, showing that modern softwares (some of them available for
example from the Molecular Simulations Inc./San Diego. CA, USA) and powerful computers (for example IBM RS 6000 workstations or Cray C916 supercomputers) are capable today to model and predict diffusional processes for a certain range of polymer penetrant systems. The spread of this range is given by the general conditions tied to the ability of the MD procedure to simulate a polymer penetrant system large enough to sample the configurational statistics of the polymer sufficiently well. For a simple polymer like linear polyethylene with flexible chains one may need a few hundred [-CH2-] repeat units or a few hundred to a few thousand atoms (98). To generate a bulk PDMS structure in which 3 water molecules are “inserted” 220 monomer units [-Si(CH3)2-O-], i.e. 2238 atoms, were for example used in (119). One might expect that many more repeat units are needed if the polymer has stiff chains (98). However, it should be noted that it is the number of flexible bonds in a chain and not just the number of repeat units that is a decisive parameter for the achievable quality of the amorphous polymeric structure generated from a chain (143). Other factors determining the range of application of the MD method arise from the mobility of the penetrant itself. To be sufficiently precise with the computer simulation one needs to observe, say, 10 jump events for every single penetrant (which is probably the bare minimum). At equilibrium and assuming hopping motion the diffusion coefficient can be given by Eq. (5-3), where h is now the mean-square “jump” distance and v-’ the average residence time between jumps. Hence for a D of about 5 x lo-‘ cm2/s (a comparatively high diffusion coefficient for packaging applications) and a “jump distance” of about 0,5 nm (see (117) for example) one finds that in an 1 ns simulation one will encounter about 12 jumps on average. It is interesting to notice that if the MD simulation is done in steps of 1 fs (121) 10‘ time steps must be computed to complete a 1 ns simulation. To simulate with MD slower diffusion processes, i.e. smaller D, one must either extend the duration of the simulation (and hence the computing time and costs) or to “insert” several penetrants at the same time in the generated polymer structure and thereby improve the quality of the sampling (98,117,119,120). However, the later option is valid only if the diffusion coefficient is not very sensitive to the penetrant concentration. With nowadays softwares and computers MD simulations can be extended to about 10 ns which brings the D of about 5 . cm2/swithin reach of the method. Diffusion processes which evolve at a rate of 5 . 10-’cm2/s or faster are typical for: - the diffusion, at very low concentrations, of small penetrants (simple gases or vapors) in low barrier polymers: i.e. polyethylenes (112,1.51), polypropylenes (160), polybutadienes (149-151) and siloxanes (112,119,144) at room temperature or polystyrene (116), polyethylenetherephthalate ( I 17) well above room temperature, - the diffusion, at room temperature, of simple gases and vapors through glassy polymers with large interchain regions: i.e. Poly[ 1-(trimethylsily1)-1-propyne](1 17) and cis-poly(tert-butylacetylene) (161). However in the packaging sector the large majority of the diffusion processes in polymers imply penetrants with a relative molecular weight ranging between 100 and 1200 daltons and have often quite complex structures. From experiments one knows that these diffusion processes are characterized by D ranging from lo-’ to 10-’2cm2/s or even lower levels (see Appendix I). In (98) it was stated that, to study with MD techniques polymer penetrant systems in which the D are that small, is certainly out of reach for several generations of supercomputers to come.
148
Mercea
The posibility of extending MD to slower diffusion processes has been discussed (98). But applying such algorithms has a tradeoff on the overall quality of the computational approach. To perform calculations at time scales beyond those accessible to MD is possible nowadays only by using the transition state approach (TSA) proposed in (97,115,132). This method will be presented briefly below.
5.2.2 The transition-state approach As already mentioned in Section 5.1.1 one of the early theoretical models of gas diffusion in solid polymers (3,37,162) was based on the Transition-State Theory (TST) (40). More than fifty years ago it was assumed ad hoc that gas molecules move through a dense polymer in a series of activated “jumps” between “holes” which exist in the polymer matrix. Fortunately, results of “ab initio” MD simulations, Section 5.2.1, demonstrate that the computed trajectories of small penetrants in atomistic structures of dense polymers are consistent with the “heuristic” picture of this early “classical’’ model. In its framework it was estimated, from solubility data, that at room temperature the vibrational frequency v,, of the gas molecule trapped by the surrounding chains is of about 10l2 ssl (163). This finding is also in reasonable agreement with the bouncing frequency of a small gas molecule inside a “cavity” of the polymer matrix, as found in MD simulations. These results indicate that the “jumps” of a penetrant in a dense polymer could be treated as an elementary process, thus justifying the use of TST for developing a computer simulation technique to evaluate the rate of the penetrant’s jumps and out of this the diffusion coefficients. The development of a Transition-State Approach (TSA), based on a simplified description of thermal motions in the host matrix and stochastic methods in treating the penetrant dynamics, promises to allow much longer simulation intervals than MD can practically achieve nowadays (about 10 ns). This feature is important because: (i) the occurence, in some polymer penetrant systems, of anomalous diffusion (115,130) leads to the necessity of carrying out very long MD simulation runs for penetrants to enter the Einstein diffusive regime (97,98) and (ii) unpracticably long MD simulations would be needed to simulate and predict slower diffusion processes, Section 5.2.1 and Appendix I. In the development of the TSA besides the “jumping” mechanism already mentioned another fundamental mechanistic feature assumed is that the penetrant dynamics is coupled to the elastic motion of the polymer chains, but, to a first approximation, is independent from the structural relaxations of the matrix (973 15,130,132). The thermal motion causes the polymer matrix to move in its configurational space. At short times the vibrational modes of motion dominate: vibration of chemical bonds or bond-anlges, small-amplitude rotations of side groups or wiggling of torsion angles. As time goes by, the system tends to perform structural relaxation for example through torsional transitions in the main chain or in side groups. Using MD to simulate an appropriate penetrant trajectory one can specify an upper bond for times at which the system at hand can be treated as essentially executing elastic motions (97). Elastic motion implies that the atoms of the matrix fluctuate about their equilibrium positions. Allow now a small dissolved molecule to reside in the system and suppose that one can neglect the correlation between the structural relaxation of the matrix and the dynamics of the penetrant. In this case one can write a penetrant distribution
Models for diffiision in polymers
149
function p(r) which is obtained by integrating over all possible values of the deviations of the host atoms the result of the potential energy of interaction between the dissolved molecule and the host atoms and a normalized probability density, W((A)), describing the elastic fluctuations (132). The function p(r) is related to the Helmholtz energy, A(r), of the dissolved molecule at location r according to a general equation given in (164). The TST can be used then for describing the spatial movement of a dissolved molecule as a series of activated jumps between adjacent local minima of A(r) (132). The rate constants Ri.j for the penetrant’s transition from site i to site j can be written as (40): (5-11)
where Q,,, and Q, denote partition functions of penetrant on the crest surface between sites i and j and in site i , respectively. In Eq. 5-1 1 k* is a transmission factor taken to be about 0.5 (132). It was shown that in the quasi-classical case one can link Q,,, and Q, to the function p(r) (164). Hence, specification of the elastic fluctuations of the atoms of the host matrix through the probability density W((A))yields p(r) which, in turn, yield the transition rates R,,, (130). If the network of local minima of A(r) with the associated R,.,’s are known, one can use stochastic methods to evaluate the correlation function describing the penetrant dynamics (130,132). The procedures of simulating the dynamics of guest molecules on the network of sites and of evaluating W( (A)) were described in (1 30) and (132), respectively. An important parameter in these procedures is the mean-square deviation, (Am2), of host atom o! from its average position. The values of (A$) are expected to depend on the time scale of averaging: for very short times (Aa’) increases with time approaching then, by definition of elastic motion, an asymptotic value. Using atomistic short-scale trajectories calculated with MD and specifying an averaging time one can calculate for (Am2) a “smearing” factor (A2) and use it in the TSA simulations (97,132). Another possible way to evaluate (A2) is to match the short-time region of the meansquare displacement, (r2), of the penetrant versus time curves obtained from TSA with those from MD calulations (97). To follow to actually carry out a TSA simulation a three-dimensional grid, with grid interval of about 0.2 A ( 5 . lo6 equispaced points in (132)) is built and the Helmholtz energies at all grid points are computed. Before this can be done in practice, a value for (A2)must be found. Then, local minima and the crest surfaces must be found, using the procedures given in (130,132,165). To study the dynamics of the penetrant molecules on the network of sites a Monte-Carlo procedure is employed, which is presented is some detail in (97). Eventually the stochastic trajectory of a dissolved molecule is obtained and subsequently by averaging a large number of such trajectories, about lo3 in (132), the diffusion coefficient D of the penetrant in the polymer can be calculated from the plot of (r2) versus the time t (using for the linear portions (Einstein diffusion) of the curves a simple equation similar to Eq. 5-3). In Figure 5-7 the (r2)’s of He and Ar in glassy polycarbonate, PC, at 300 K , as calculated with TSA, are shown. The results plotted in this figure represent averages over 500 independent simulation paths. The simulations presented in Fig. 5-7 show a region of “anomalous diffusion” of the penetrant He for (r2)’ssmaller than =lo3A2(simulation interval of ~ 0 . ns) 5 . This is similar those reported in (98,166) on the MD simulation of H e diffusion in rubbery polyisobutylene, where the transition to normal diffusion was captured at around (r2)=10A2 and a sim-
150
Mercen
-14
-12
-10
-8
lg t (s)
-6
’
Figures-7: Computed dynamics of He and Ar in polycarbonate at 300 K (132).
ulation interval of 4 . 1 ns. It is believed that this anomalous behavior is caused by a separation of time scales consistent with the jumping pattern (98). The very fast motions of the penetrant molecules inside the cavities (timescales of several 100 ps) is determined by the shape of these cavities. Therefore these motions don’t have a random-walk-like behavior and consequently it is not appropriate to use the Einstein equation, i.e. D = (r2)/6t (which similar to Eq. 5-3), to calculate D. In fact the Einstein equation holds true if the slope of the log (r2)versus log t plot is equal to one. A direct consequence of this fact is that, in order to predict diffusion coefficients, a MD or TSA computation must simulate a time interval long enough to get fulfiled the above requirement. For some polymer penetrant systems this means already the need to carry out simulations over time intervals that are out of reach of the MD method ( t > 10 ns) (120,130,132). In these cases the method of choice will be the TSA. In Table 5-2 a comparison between diffusivities obtained with the TSA method and experimental D is presented. From this table one can see that, in all cases computed D agree with experimental data to within an order of magnitude. Moreover most of these D are considerably smaller than the 5 . lo-’ cm2/s lower threshold assumed to be in reach of nowadays MD simulations Section 5.2.1. This is an encouraging sign that computer simulations of diffusional processes are already able to predict, with a reasonable accuracy and for small and simple penetrants, diffusion coefficients around cm2/s. From the point of view the packaging sector it would be interesting to learn if and when further theoretical developments of the TSA method will be able to simulate (predict) such slow diffusional processes for organic penetrants with a much more complex structure, see Chapter 3 and Appendix I. Two “atomistic” approaches have been presented briefly above: molecular dynamics and the transition-state approach. They are still not ideal tools for the prediction of diffusion constants because: (i) in order to obtain a reliable chain packing with a MD simulation one still needs the experimental density of the polymer and (ii) though TSA does not require classical dynamics it involves a number of simplifying assumptions, i.e. duration of jump mechanism, elastic polymer matrix, size of smearing factor, that impair to a certain degree the “ab initio” character of the method. However MD and TSA are valuable achievements, they are complementary in several
151
Models f o r diffiisinn in polyniers
Table 5-2: Diffusion coefficients calculated with the transition-state approach and from experiment. Polymer
Diffusant
D"dC (cm'is) lo7 Cnl ( K )
Ref.
Dex7 (cm2/s)10 @I ( K )
35.0 (300)
132
64.6 (308)
Ref
Pol ycarbonate
He
Pol ycarbonate
0 2
0.10 (300)
132
0.56 (308)
167
Polycarhonate
N2
0.(19 (300)
112
0.18 (308)
167
Pol yamidimide
H2
120
9.4 (300)
I20
Polyamidimide
0 2
0.40 (300)
120
0.30 (300)
120
Polyamidimide
NZ
0.20 (300)
120
0.10 (300)
120
Polyimide
0 2
15.3 (300)
120
7.40 (300)
120
15.9 (300)
Polyimide
N7
2.6 (300)
120
Polyvinylchloride
He
17.0 (318)
97
40.0 (318)
2.80 (300)
167
I20
147.168,169
Polyvinylchloride
Ne
2.0 (318)
97
4.0 (318)
147,168,169
Polyvinylchloride
Ar
0.04 (318)
97
0.05 (318)
147.168.169
Pol yvinylchloride
Kr
0.003 (318)
97
0.01 (318)
147,168,169
ways and can be used to predict the diffusion coefficients of small penetrants (so far simple gases and simple organic vapors) in both rubbery and glassy amorphous polymers. These computational methods can be used to understand the behavior of small penetrants in the matrix of a polymer starting from an "atomistic level" and without ad hoc assumptions on the movements of the polymer chains. In this respect M D is the less coarse-grained of the two methods. The main drawback of M D is the computational cost that nowadays prohibits simulations beyond 10 ns, which are still being far from routine. The TSA is well suited to extend the time-scale of simulations, bringing new phenomena within reach. In this respect it is important to use M D and TSA in conjunction. The limitations of the TSA. as developed so far, are evident when one intends to simulate' penetrant polymer systems where there is strong interaction between the penetrant and the host atoms, or where larger penetrant molecules require a deformation of the polymer structure for their passage. In such systems, as well as in systems where the penetrant induces a swelling of the polymer matrix, MD seems to be the method of choice to properly simulate the diffusion mechanism (125,126,170).
5.3 Conclusions A process or manufacturing engineer is often confronted with the difficult and expensive task of measuring experimentally the migration (diffusion) of rather complex organic molecules in rubbery o r glassy semicrystalline polymer matrices. For such systems the knowledge/prediction of diffusion coefficients would he crucial for the theoretical estimation of substance transfer for example from a polymeric packaging into the wrapped good (foodstuff, medicine, etc.). Therefore a theoretical method/model for performing the true prediction of diffusion coefficients for small organic penetrants in rubbery and glassy polymers would be of great help to reduce
152
Mercea
the costs and worktime nowadays spent in the field of polymer packaging research and law enforcement. The problem is that ideally such a theoretical method/model should be as simple as possible, rely on parameters, which for the penetrant polymer systems specific in the packaging sector, are well known and easily available and, at last but not at least, the use of the method to predict diffusion processes should not consume more time and resources than the direct migration/diffusion experiments. If a given diffusion model cannot meet the one or the other of these requirements, from a purely pragmatic point of view, a process engineer or law enforcer may not see incentives to use the theoretical approach instead of a well established experimental one. Unfortunately, it seems that none of the diffusion models presented in the above sections meets completely these practical goals. It is beyond any question that the type of “classical” diffusion models presented in Section 5.1 were, at the time of their conceivement, important steps for the qualitative understanding of the phenomenology of penetrant diffusion in polymers. Moreover some of these models are very successful in rationalizing average experimental diffusion coefficients with macroscopic parameters as temperature and penetrant concentration. Trying to use these models for predicting diffusion coefficients for penetrant polymer systems which are specific in the packaging sector one is confronted with several problems. First, with no exception, in all “classical” diffusion models one or more adjustable parameters enter in the formula of D. To calculate the magnitude of thislthese parameter/s a number of diffusion experiments must be performed with the very penetrant polymer system which one intends to simulate theoretically. In practice such experiments most often require quite sophisticated equipment to obtain the experimental data, and often non-trivial theoretical schemes to evaluate them. The attempt to save experimental work by using the adjustable parameters determined for a certain penetrant polymer system in order to estimate/predict Ds in a related system is generally not recomendable. Hence, in a first step, in order to use one or other of the “classical” diffusion models, one is forced to replace migration experiments with diffusion ones. Then, as already mentioned, once all adjustable parameters in the formula of D are known semi-predictions and predictions of D can be made most often only if the physico-chemical parameters of the system (temperature, concentration, pressure, degree of swelling, etc.) do not vary beyond a relatively limited range. Finally, in some of the most widely used “classical” models - the free-volume models of Fujita, Vrentas and Duda and their alternatives (171-175) - more than a dozen structural and physical parameters are needed to calculate the free-volume in the penetrant polymer system and subsequently the D. This might prove to be a relatively simple task for simple gases and some organic vapors, but not for the non-volatile organic substances (rest-monomers, additives, stabilizers, fillers, plasticizers) which are typical for polymers used in the packaging sector. As suggested indirectly in (17) sometimes in the future it will maybe possible to calculate all the free-volume parameters of a “classical” model by using MD computer simulations of the penetrant polymer system. On the other hand, based on the rapid progress which was recorded in the last decade in the “atomistic” simulation of diffusion processes in polymers one may be confident that these computational methods will be one day able to cope with the prob-
Models for diffiision in polyniers
153
lem of a true prediction of D for the type o f migration estimations envisaged with polymeric packagings. In our oppinion this will be not an easy target to reach. As is well known todays MD simulations are better suited to describe at a true atomistic level the host matrix and the dynamics of the penetrants. However, most of the MD performed so far are dealing with purely amorphous polymers and with very simple penetrants. In the packaging practice however most of the polymers are partly crystalline and the penetrants are often complex organic molecules. In (98) it was mentioned that a straightforward atomistic MD simulation of a semicrystalline material is not yet achievable, since crystallite dimensions may range from several 10 nm to several microns and crystallites often aggregate to form larger domains of macroscopic dimensions (3536). In contrast, typical MD simulations use, for completely amorphous structures, cells with a length of a few nm. Therefore to simulate a semicrystalline cell several orders of magnitude larger seems to be completely out of question for nowadays computers. The possibility to adopt a less atomistic viewpoint and use a Monte-Carlo 2-phase simulation technique for semicrystalline polymers was analysed in (98). One should also not forget that the typical organic molecule migratingldiffusing from a polymeric packaging has usually a geometry differing strongly from that of the penetrants investigated so far with M D simulations. Moreover, at an atomic level, the interaction of most such organic molecules with the host matrix is much stronger and difficult to quantify that the interaction of simple permanent gases with the same matrix. If further developments of the MD and/or Monte-Carlo 2-phase techniques will be able to simulate at an atomistic level the dynamics of a semicrystalline polymer and of a complex organic penetrant the question remains: how long will be the time interval simulated? According to those mentioned above in Section 5.2.1 simulations of a few 100 ns to a few ps are needed to predict D in the range of 10-"' to 10-"cm2/s, which is often found in technical applications of polymers. From todays perspective the computer time (and costs) needed for a MD simulation of such duration are out of reach in the near future. With the TSA developed in (115,130,132,165) it was possible to almost reach simulation intervals of 1 milisecond. This makes in principle possible to predict D as small as a few cm2/s. Therefore the TSA seems to be a good choice to predict D for the type of diffusion processes encountered in packaging applications. But for this, the actual TSA algorithms must be developed to take also into account strong interactions between the penetrant and the host atoms, and the deformation of the polymer structure at the passage of complex penetrant molecules. We are confident that sometimes in the future suitable computational approaches and powerful hardwares will be available to predict D of additives, stabilizers, monomers, dyes and/or plasticizers in polymeric materials used in packaging applications. To evaluate, if such an endeavour may help to reduce the considerable volume and costs of experimental migration testings peformed nowadays, it is necessary to consider also the following aspects. How much software development and computing time will be needed to predict the D for a penetrant polymer system not yet investigated? In (120) it was stated that even the rather fast TSA simulation technique will presumably not lead to a fast predictability of transport paramaters for large numbers of hypotetical polymers in the near future. This was mainly atributed to the fact, that the construction of well equili-
154
Mercea
brated polymer packing models is still demanding large amounts of computer time (not to mention the much longer time needed to effectively develop the appropriate algorithms). Then an important aspect is how precise the predicted D will be? So far an agreement within one order of magnitude between an experiment and an atomistic simulation is considered to be a good achievement. For completely amorphous polymer structures and simple penetrants even better agreements have been reported in Tables 5-1 and 5-2. From the point of view of estimating the migration from polymeric materials used in the technical sector a prediction of D within the order of magnitude of the experimental one would be a result of certain practical use, see Chapter 15. The question is: to what sophistication must be developed the computer simulation approach to meet this requirement also for the type of penetrant polymer systems which are usual in the named sector? In the end it is legitimate to mention that for a considerable number of process engineers and law enforcement personnel the material costs of using an atomistic computational approach to predict a D and subsequently use it in a migration estimations will also play an important role. Pragmatically speaking one can expect that somebody interested to reduce its expenses for migration testings from polymeric packagings, will not have to much interest to replace these tests with much more expensive and less precise theoretical simulations! Therefore, from the point of view of the practical value of migration estimations in the technological sector, it will be maybe worthwhile to compare the trade-off between the cost and precision of estimating a D with the “upper bond” concept presented in Chapter 15 with the cost and precision of predicting the same D with an atomistic computer simulation (when this will be achievable). References I . Mitchell, J.K., Philadelphia J.Med.Sci., 13 (1831) 36.
2. Graham, T., Phil.Mag., 32 (1866) 401. 3. Barrer. R.M.. “Diffusion in and through Solids”. Cambridge University Press. Cambridge, 1951.
4. Tuwiner. S.B.. “Diffusion and Membrane Technology” ACS Monographies. Reinhold. New York,1962. 5. Rogers, C.E., “Solubility and Diffusivity” in “Physics and Chemistry of the Organic Solid State”, Fox. D., Labes. M.M.. Weissberger. A.. (Eds.),Intescience, New York, 1965, p. 509. 6. Crank, J., Park, G.S., “Diffusion in Polymers”. Academic Press, London, 1968. 7. Stannett, V.T., Hopfenberg, H.B., Petropoulos, J.H., “MTV 1nt.Rev.Sci.. Macromol. Sci.. 8 (1972) 329. 8. Hwang, S.-T.. Kammermeyer, K., “Membranes in Separations”, Wiley Interscience. New York. 1975. 9. Vieth, W.R., Howell, J.H.. Hsieh, J.H.. J. Membrane Sci., l(1976) 177. 10. Meares, P., “Membrane Separation Processes”, Elsevier Scientific, New York, 1976. 11. Stannett,V.T.. Koros, W.J., Paul, D.R., Lonsdale, H.K., Baker, R.W., Adv.Polyrn.Sci., 32 (1979) 71. 12. Mason, E.A.. Lonsdale, H.K., J. Membrane Sci.. 51 (1990) 1. 13. Frisch. H.L., Stern, S.A., “Diffusion of Small Molecules in Polymers”. CRC Crit.Rev. Solid State and Materials Sci. 11 (1983) 123. 14. Rogers, C.E., Machin. D., CRC Crit.Rev. Macrornol. Sci. (1972) 245. 15. Vieth. W.R.. “Diffusion in and through Polymers”. Hanser, Munchen, 1991. 16. Koros. W.J., (Ed.), “Barrier Polymers and Structures”, ACS SyrnpSer. 423, Arn.Chern. Soc., Washington, 1990. 17. Stern. S.A., J. Mcmbrane Sci., 94 (1994) 1.
18. Aminabhavy. T.M., Shanthamurthy, U.. Shukla. S.S.. J.Macromol. Sci., Rev.Macromol.Chem Phys.. C28 ( 1988) 421. 19. Paul. D.R., Yampol’ skii, Yu. P.. “Polymeric Gas Separation Membranes”. C R C Press. Boca Raton. 1994.
20. 2I. 22. 23. 24. 25. 26. 27. 28. 2Y. 30. 31. 32. 33. 34. 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48.
49. 50. 51. 52. 53. 54.
55. 56. 57. 58. 59. 60.
61. 62. 63. 64. 65. 66.
Schlotter N.E., Furlan. P.Y., Polymer. 33 (1992) 3323. Piringer, 0..”Verpackungen fur Lebensmitteln“. VCH, Munchen. 1993. Comyn. J.. ”Polymer Permeability”. Elsevier Applied Science. New York, 19x5. Clough, R.L., Billingham. N.C.. Gillen, K.T.. (Eds.). “Polymer Durability: Degradation. Stabilization and Lifetime Predictions“, ACS Adv. Chem. Ser. 249 -1985. Vergnaud. J.M., “Liquid Transport Processes in Poymeric Materials”. Prentice Hall. Engelwood Cliffs. 1991. Scott. G.. (Ed.). ”Developments in Polymer Stabilisations-3”. Elsevier Applied Science, London. 1980. Hausschild, G., Spingler, E., “Migration bei Kunststolfverpackungen”, Wissenschaftliche VGmbH, Stuttgart. 1988. Stastna. J.. DeKee. D.. “Transport Properties in Polymers”. Technomic. Lancaster, 1995. Frisch, H.L.. J.Chem.Phys.. 37 (1962) 2408. Frisch. H.L., Polym.Eng.Sci.,20(1980) 2. Alfrey. T.. Gurnee. E.F., Lloyd. W.G., J. Polym.Sci.. C12. (1966) 249. Hopfenberg. H.B.. Stannett, V.T.. (Eds.) ”Permeability of Plastic Films and Coatings to Gases. Vapors and Liquids”. Plenum Press. New York.1974. Paul. D.P.. Koros, W.J.. J.Polyrn.Sci.. Polyni.Phys.Ed.. 14 (1976) 675. Stern. S.A.. Saxena. V.. J. Membrane Sci.. 7 (1980) 47. Saxena. V.. Stern. S.A.. J. Membrane Sci.. 12 (1982) 65. Cussler, E.L.. Hugcs. S.E.. Ward, W.J., Ark. R.. J. Membrane Sci., 38 (1988) 161. Cussler. E.L.. J. Membrane Sci., 52( 1990) 275. Barrer. R.M.. Trans. Faraday SOC..35 (1939) 262 & 644. Barrer. R.M., Trans. Faraday Soc.. 38 (1942) 321. Meares, P., J.Am.Chem.Soc..76 (1954)3415. Glasstone. S., Laidler. K.J., Eyring, H., ”The Theory of Rate Processes”. McGraw-Hill. New York. 1941. Meares, P.. Eur.Po1ym.J.. 29 (1993) 237. Brandt. W.W.. J.Phys.Chem., 63 (1959) 1080. DiBenedetlo, A.T.. J.Polym.Sci.. A1 (1963) 3459. DiBenedetto. A.T..J.Polym.Sci.. A1 (1963) 3477. Pace. R.J.. Datyner. A,. J.Polym.Sci., Polym.Phys.Ed.. 17 (1979) 437. Pace. R.J., Datyner, A,, J.Polym.Sci., Po1ym.Phys.Ed.. 17 (1979) 453. Pace. R.J., Datyner. A,, J.Polym.Sci.. Polym.Phys.Ed.. 17 (1979) 465. Chandrasekar. S.. Rcv.Mod.Phys.. 15 (1941) 1. Wheeler. T.S., Trans.Nat.Sci.1ndia. 1 (1938) 313. Kloczkowski, A,. Mark. J.E.. J.Polym.Sci.Part B: Polyrn. Phys. 27 (1989) 1663. Fujita, H., Fortschr. Hochpolym. Forsch.. 3 (1961) I. Fujita. H.. Macromolecules, 26 (1993) 643 & 4720. Guo. C.J.. DeKee. D.. Harrison. B., Chem.Eng.Sci., 47 (1992) 1525. Vrentas, J.S.. Duda. J.L.. in “Encyclopedia of Polymer Science and Engineering”. 2nd Ed.,Vol. 5, Wiley. New York. 1986. Cohen, M.H.. Turnbull. J D.. Chem.Phys.. 31 (1959) 1164. Hirschfelder, J.O.. Curtis, C.F.. Byrd. B.R.. “Molecular Theory of Gases and Liquids”, Wiley. New York, 1954. Meares. P..J.Polym.Sci.. 27 (1958) 391 & 405. Kokes. R.J.. Long. F.A.. Hoard, J.L.,J.Chem.Phys., 20 (1952) 1711. Bueche. F.. J.Chem.Phys., 21 (1953) 1850. Fujita. H.. Kishimoto, A,. Matsumoto, K., Trans.Faraday SOC.,58 (1960) 424. Vrentas, J.S., Duda. J.L.. Ling, H.-C.. Macromolecules. 21 (1988) 1470. Vrenlas. J.S.. Duda. J.L., Ling, H.-C., Hou. A,-C.. J.Polym.Sci.. Polym.Phys.Ed.. 23 (1985) 275 & 289. Vrentas. J.S., Vrentas. C.M.. Macromolecules. 27 (1YY4) 4684. Vrentas, J.S., Duda. J.L.. Hou. A,-C..J.Appl.Polym.Sci.. 33 (1987) 2581 Vrentas. J.S.. Vrentas. C.M.. Macromolecules. 27 (1994) 5570. Ganesh. K., Narajan. R.. Duda, J.L.. Ind. Eng.Chem.Res., 31 (1992) 746.
156
Mercea
67. Vrentas, J.S., Duda. J.L., Ling, H.-C.. J.Appl.Polym.Sci., 42 (1991) 1931. 68. Vrentas, J.S., Duda, J.L., J.Polym.Sci.,Polym.Phys.Ed., 15 (1977) 403.
69. Vrentas. J.S., Duda, J.L, J.Polym.Sci.,Polym.PhysEd., 15 (1977) 417. 70. Vrentas, J.S.. Duda, J.L., J.Polym.Sci.,Polym.Phys.Ed.. 15 (1977) 441. 71.Vrentas, J.S., Duda, J.L., J.Appl.Polym.Sci., 21 (1977) 1715. 72. 72. Vrentas, J.S., Duda, J.L., J.Appl.Polym.Sci.. 22 (1978) 2325. 73. Duda, J.L., Vrentas, J.S., Ju, S.T.. Liu. H.T.. AIChEJ. 28 (1982) 279 74. Haward, R.N., (Ed.) “The Physics of Glassy Polymers”, Applied Science Publ., London, 1973. 75. Meares, P., Trans. Faraday SOC..53 (1957) 101. 76. Meares, P., Trans. Faraday Sac.. 54 (1958) 40. 77. Barrer. R.M., Barrie, J.A.. Slater, J., J.Polym.Sci., 27 (1958) 177. 78. Fowler, R.H., Guggenheim. E.A., “Statistical Thermodynamics”, Cambridge Univ. Press, Cambridge, 1949. 79. Barrer. R.M., Trans. Faraday SOC.,43 (1947) 3. 80. Michaels, AS., Vieth, W.R., Barrie, J.A., J.Appl.Phys., 34 (1963) 1 & 13. 81.Pau1, D.R., J.Polym.Sci.,A-2,7(1969)1811. 82. Petropoulos, J.H., J.Polym.Sci., A-2,8(1970) 1797. 83. Tshudy, J.A., von Frankenberg, C., J.Polym.Sci., A-2.11 (1973) 2077. 84. Crank, J., “Mathematics of Diffusion”, 2nd Ed., Claredon Press. Oxford, 1975 85. Wang, T.T., Kwei, K.T., Frisch H.L., J.Polym Sci., A-2.7 (1969) 879. 86. Fredrickson, G.H., Helfand, E., Macromolecules, 18 (1985) 2201. 87. Vieth, W.R., Sladek, K.J., J.Colloid Sci., 20 (1965) 1014. 88. Toi, K., Maeda, Y., Tokuda, T., J.Appl.Polym.Sci.. 28 (1983) 3589. 89. Chern, R.T.. Koros, W.J.. Sanders E.S.. Chen, S.H.. Hopfenberg, H.B.. Am.Chem.Soc., Symp.Ser.. 223 (1983) 47. 90. Pace, R.J., Datyner. A.. J.Polym.Sci., Polym.Phys.Ed., 18 (1980) 1103. 91. Vrentas, J.S., Duda, J.L.. Ling. H.-C., J.Polym.Sci.. Polym.Phys.Ed.,26 (1988) 1059. 92.Vrentas, J.S., Vrentas, C. M., J.Polym.Sci.. Polym.Phys.Ed., 30 (1992) 1005. 93. Vrentas, J.S., Liu, H.T., Duda, J.L.. J.Appl.Polym.Sci., 25 (1980) 1297. 94. Holley, R.H., Hopfenberg. H.B., Polym.Eng.Sci., 10 (1970) 376. 95. Catlow. C.R.A., Parker, S.C., Allen, M.P.. (Eds.) “Computers Simulation of Fluids, Polymers and Solids”, Kluwer, Dordrecht, 1990. 96. Roe, R.-J., “Computer Simulations of Polymers“. Prentince Hall, Englewood Cliffs, 1991. 97. Gusev, A.A., Muller-Plathe, F., van Gunsteren. W.F.. Suter, U.W.. Adv. Polym. Sci., 116 (1993) 207. 98. Muller-Plathe, F.. Acta Polymerica, 45 (1994) 259. 99. Theodorou, D.N.. in “Diffusion in Polymers”, Neogi, P.. (Ed.). Marcel Decker, New York.1996. 100.Jagodic, F., Borstnik, B.. Azman. A., Makromol.Chem., 173 (1973) 221. 101. Rigby. D.,Roe, R.-J., J.Chem.Phys..89 (1988)5280. 102. Boyd, R.H., Pant, K.. Polym. Preprints, 30 (1989) 30. 103. Shah, V.M.. Stern, S.A., Ludovice, P.J., Macromolecules, 22 (1989) 4660. 104.Trohalaki. S.. Rigby. D., Kloczkowsi. A., Mark, J.E., Roe, R.-J., Polym. Preprints, 30 (1989) 23. 105.Takeuchi, H., Okazaki, K., J.Chem.Phys., 92 (1990) 5643. 106. Takeuchi, H., J.Chem.Phys.. 93 (1990) 2062 & 4490. 107. Takeuchi. H.. Roe. R.-J., Mark. J.E., J.Chern.Phys.. 93 (1990) 9042. 108. Boyd, R.H., Pant, K., Macromolecules, 24 (1991) 6325. 109. Miiller-Plathe. F.. J.Chem.Phys., 94 (1991) 3192. 110. Sok, R.M., Berendsen, H.J.C., van Gunsteren, W.F.. J.Chem.Phys.. 94(1992) 4699. 111.Tamai. Y., Tanaka, H.. Nakanishi, K., Macromolecules, 28 (1995) 2544. 112.Tamai. Y., Tanaka, H., Nakanishi, K., Macromolecules, 27 (1994) 4498. 113. Miiller-Plathe. F., J.Chem.Phys. 94 (1992) 3192. 114. Miiller-Plathe. F., J.Chem.Phys., 98 (1993) 9895. 115. Gusev. A.A., Arizzi. S., Suter. U.W.. Moll, D.J., J.Chem.Phys., 99 (1993) 2221. 116.Han. J.. Boyd. R.H.. Polymer 37 (1996) 1797. 117. Bharadwaj, R. K., Boyd, R.H., Polymer, 40 (1999) 4229. 118. Niemela, V. S., Lepanen, J., Sundholm. F.. Polymer. 37 (1996) 4155. 119. Fritz, L.. Hofmann. D.. Polymer, 38 (1997) 1035. 120. Hofmann. D.. Fritz, L., Ulbrich, J., Paul, D., Polymer. 38 (1997) 6145. 121. Fried, J.R., Goyal, D.K.. J. Polym.Sci.. Part B. Polym.Phys., 36 (1998) 519. 122. Hedenqvist, M.S.. Bharadwaj, R., Boyd. R.H.. Macromolecules, 31 (1998) 1556. 123.Tamai, Y.. Tanaka. H., Nakanishi, K.. Macromolecules. 29 (1996) 6750 & 6761.
Models for diffiisiorz irz polyrners
157
124. Miiller-Plathe. F.. Macromolecules, 29 (1996) 4782. 125. Muller-Plathe, F., van Gunsteren, W. F., Polymer, 38 (1997) 2259. 126. Muller-Plathe, F., J.Chem.Phys., 108 (1998) 8252. 127. Allen, M.P.. Tildesley, D.J., ”Computer Simulation of Liquids and Solids”, Oxford University Press. Oxford. 1987. 128. van Gunsteren. W.F., Weiner. P.K., (Eds.) “Computer Simulation of Biomolecular Systems”, ESCOM. Leiden. 1989. 129. Baranyai. A,, J.Chem.Phys.. 101 (1994) 5070. 130. Gusev. A.A.. Suter. U.W., Polym.Preprints. 16 (1992) 631. 131. Gusev. A.A., Suter, U.W.. Makromol.Chem.,Macromol.Symp., 69 (1993) 229. 132. Gusev. A.A.. Suter. U.W., J.Chem.Phys.. 99 (1993) 2228. 133. Muller-Plathe, F.. Chem.Phys.Lett.. 177 (1991) 527. 134. de Vos. E.. Bellemans. A.. Macromolecules. 7 (1974) 812. 135. Skvortsov, A.M.. Sariban, A.A., Birshtein. T.M.. Vysokomol. Soeden.. 25 (1977) 1014. 136. De Santis, R., Zachmann, H.G., Prog.Colloid.Poly.Sci., 64 (1978) 281. 137. Wall. F.T., Seitz, W.A., J.Chem.Phys., 67 (3977) 3722. 138. Bishop. M., Ceperley, D., Frisch, H.L., Kales. M.H., J.Chem.Phys.. 72 (1980) 322. 139. Weber. T.A.. Helfand, E., J.Chem.Phys., 71 (1979) 4760. 140. Theodorou, D.N.. Suter. U.W.. Macromolecules. 18 (1985) 1206 & 1467. 141.Theodorou, D.N., Suter, U.W., J.Chem.Phys.. 82 (1985) 955. 142. Muller-Plathe. F., “Generating Starting Structures for Polymer Simulations”, Report CECAM, April 13-16. 1993, Orsay, France. 143. Hofman. D.. Ulbrich. J., Fritsch, D.. Paul, D., Polymer. 37 (1996) 4773. 144. Sok. R.M., Berendsen. H.J.C., van Gunsteren. W.F.. J.Chem.Phys, 96 (1992) 4699. 145.Barrer,R.M.,Choi, H.T.. J.Polym.Sci., lO(l965) 111. 146. Stern, S.A.. Shah, V.M.. Hardy, B.J.. J.Polym.Sci.. Polym Phys. Ed.. 25 (1987) 1263. 147. Okamoto. K., Nishioka. S.. Tsuru, S., Sasaki, S., Tanaka, K.. Kita, H.. Kobunshi Ronbushu. 45 (1988) 993. 148. Muller-Plathe. F., Rogers. S.C.. van Gunsteren. W E . J.Chem. Phys., 98 (1993) 9895. 149. 149. Muller-Plathe, F., Rogers, S.C., van Gunsteren. W.F.. Macromolecules, 25 (1992) 6722. 150. Pant. P.V.K.. Boyd, R.H., Macromolecules. 26 (1993) 679. 151. van Amerongen. G.J., J.Polym.Sci., 5 (1950) 307. 152. Lundberg. J.L.. Mooney, E.J., Rogers. C.E., J.Polym.Sci.. 7 (1969) 947. 153. Michaels, AS.. Bix1er.H.J.. J.Polym.Sci.,Q (1961) 413. 154. Miiller-Plathe. F.. J.Chem.Phys., 96 (1992) 3200. 155. Mcrcea. P.. Fraunhofer-Institute ILV Report 1/96. Munich, 1996. 156. Fritsch. D., Peinemann, K.-V., J. Membrane Sci., 99 (1995) 29. 157. Masuda. T.. Iguchi. Y., Tang. B.-Z.. Higashimura, T.. Polymer, 29 (1988) 2041. 158. Srinivasan. R., Auvil. S.R.. Burban. EM., J. Membrane Sci.. 86 (1994) 67. 159. Barrie, J.A.. Williams. M.J.L., Munday,K.. Polym.Eng.Sci.. 20 (1980) 20. 160. Muller-Plathe, F., J.Chem.Phys.,96 (1992) 3200. 161. Jacobson. S.H.. Polym.Adv.Technol., 5 (1994) 724. 162.Barrer, R.M.. Nature. 140 (1937) 106. 163. Barrer, R.M., Trans. Faraday SOC..39 (1947) 3. 164. Landau, L.D.. Lifshitz, E.M., “Physique Theorique”. Mir, Moscow, 1967. 165. Gusev. A.A.. Suter. U.W.. Phys.Rev., A43 (1991) 6488. 166. Miiller-Plathe. F.. Rogers, S.C.. van Gunsteren. W.F.. Chem.Phys.Letts.. 199 (1992) 237. 167. Muruganandam. N.. Koros, W.J.. Paul, D.R.. J.Polym.Sci.. Polym.Phys.Ed.. 25 (1987) 1999. 168. Barrer, R.M., Mallinder. R.. Wong. P. S.-L.. Polymer, 8 (1967) 321. 169. Tikhomirov, B.T.. Hopfenberg, H.B., Stannett. V.T.. Williams, J.L.. Die Makromol. Chem. 118 (1 968) 177. 170. Muller-Plathc. F., Macromolecules, 29 (1996) 4728. 171. Kosiyanon, R.. McGregor, R., J.Appl.Polym.Sci.. 26 (1981) 629. 172. Paul. C.W.. J.Polym.Sci., Polym.Phys.Ed., 21 (1 983) 425. 173. Doong. S.J.. Ho. W.S.W., Ind.Eng.Chem.Res..31 (1992) 1050. 174. Lodge, T.P., Lee. J.A., Frick. T.S., J.Polym.Sci.. Polym.Phys.Ed.,28 (1990) 2067. 175. Frick, T.S., Huang, W.J., Tirrell. M.. L0dge.T.P.. J.Polym.Sci., Polym.Phys.Ed., 28 (1990) 2067. 176. Ichiraku. Y., Stern. S.A.. Nakagawa. T.. J. Membrane Sci., 34 (1987) 5.
Reactivity in Molecular Crystals Edited by Yuli Ohashi Copyright @ K d a o r h a Ltd .Tokyo. 1999
6 Prediction of diffusion coefficients in gases, liquids, amorphous solids and plastic materials using an uniform model Otto Piringer
6.1 Introduction Diffusion is a mass transport process resulting from random molecular motions. Such molecular motions occur in gases and condensed phases and can be described in principle as using the commonly held theoretical picture of “random walk”. This means the particles (molecules, atoms) move in a series of small random steps and gradually migrate from their original positions. Each particle can jump through a distance h in a time 7. But the direction o f each step may be different, and the net distance traveled must take the changing directions into account. The coefficient of diffusion D is related to h and z in the Einstein-Smoluchowski equation: 2
D = h
2r
If A/T = C, and h are interpreted as the mean speed of the particle and the mean free path, then Eq. (6-1) has the same structure as the following equation obtained from the kinetic theory of gases:
where k is the Boltzmann constant,
where M A H= 2((1/MA)+(1/Mfi)]-’, with molecular weights M A , and MB. oASis a characteristic length, n is the number density of molecules in the mixture, Q, is the diffusion collision integral a n d f n a correction term with the order of unity.
160
Piringer
The collision integral for diffusion depends upon the choice of the intermolecular force law between colliding molecules and is a function of temperature. The characteristic length also depends upon the intermolecular force law selected. In comparison with the simple Eq. (6-2) for perfect gases, Eq. (6-3) takes into account the interactive forces between real molecules. But, while in the first case only two specific parameters are needed, the diffusion collision integral, Q,, is a complicated function of several parameters. Whereas h and T are characteristic parameters of microscopic particle motion, the diffusion coefficient D is a specific macroscopic parameter. A main difficulty in predicting D for condensed systems lies in the derivation of correct expressions for the microscopic parameters. The most common basis for estimating diffusion coefficients in liquids is the Stokes-Einstein equation:
in which D L is related to another macroscopic parameter, the viscosity q of the medium. The solute radius is denoted by a. It must not be forgotten, however, that Eq. (6-4) was derived for a very special situation in which the solute is much larger than the solvent molecule. Nevertheless, many authors have used the form of Eq. (6-4) as a starting point in developing empirical predictions. A significant difference in Eq. (6-4) compared to Eqs. (6-2) and (6-3) for gases lies in the effect of temperature on the diffusion coefficient in liquids. This can be assumed via the viscosity q to be an exponential function of the form Aexp(-BIT). Diffusion coefficients in solids are commonly expressed as exponential functions: Ds
= Do
exp
( )::
--
(6-51
where the pre-exponential athermal factor Do and the molar enthalpy AH are estimated empirically. As shown in the previous chapter, the diffusion behavior in polymers lies between that of liquids and solids. As a consequence, the models for diffusion coefficient estimation are based on ideas drawn from diffusion in both liquids and solids. In general, diffusion coefficients in gases can be often be predicted accurately. Predictions of diffusion coefficients in liquids are also possible using the Stokes-Einstein equation or its empirical parallels. On the contrary in solids and polymers, models allow coefficients to be correlated but predictions are rarely possible. The aim of this Chapter is the development of an uniform model for predicting diffusion coefficients in gases and condensed phases, including plastic materials. The starting point is a macroscopic system of identical particles (molecules or atoms) in the critical state. At and above the critical temperature, T,, the system has a single phase which is, by definition, a gas or supercritical fluid. The critical temperature is a measure of the intensity of interactions between the particles of the system and consequently is a function of the mass and structure of a particle. The derivation of equations for self-diffusion coefficients begins with the gaseous state at pressures p below the critical pressure p p A reference state of a hypothetical gas will be defined, for which the unit value D,, = 1 m2/sis obtained at p = 1 Pa and a reference temperature, T,. Only two specific parameters, Tc, and the critical molar volume, Vc,of the mono-
Prediction of dcffiision co~ffi:cir17ts it7 gnse.~,Iiqiiids, anzory/ioris soIids ._.
161
atomic system particles are needed and, for the reference state, their corresponding values are defined by the equation of the diffusion coefficient, DG. The equation for the diffusion coefficient in a gaseous state, DG, is the starting point for the derivation of an equation for diffusion coefficients in an amorphous solid state (S). The homologous series of n-alkanes is used as a reference class of chemical compounds which asymptotically reach an unlimited molecular chain in the form of polymethylene. The diffusion coefficient, Ds,ji, is derived theoretically for a member of t h e series with j carbon atoms at infinite dilution in a matrix of a n-alkane with i carbon atoms in the molecule. In addition, the diffusion in polymethylene, which is considered as the reference structure for all polymers is also derived theoretically. The corresponding diffusion coefficient in the liquid state (L), DL,ji,is derived from D,5.jiand DG. Starting from the reference class of n-alkanes, diffusion coefficients can be estimated for any solute and matrix with corresponding specific values for the critical temperature and critical pressure of the matrix and the critical molar volume of the solute. For any polymer a value is needed for a specific structure parameter instead of the critical temperature and pressure. Due to the very complex structure of most plastic materials, this value must be determined experimentally using a reference solute in a diffusion measurement. In order to facilitate the theoretical treatment, the above mentioned homologous series of n-alkane chemical compounds is used as a reference compound class. The structures of the individual members of this series do not deviate significantly from one another. Out of all known classes of chemical compounds the saturated open-chain and non-branched (normal) hydrocarbons, the n-alkanes, or n-paraffins, represent the most frequently studied homologous series with the largest number of available members in pure form. The number of carbon atoms of a n-alkane, i, or more exactly, the i structural methylene groups including the two methyl end groups, can be interpreted in such comparisons as playing the role of i identical sub-units which compose the molecule. The properties of a macroscopic n-alkane sample can then be described as a function of i sub-units making up every molecule of the macroscopic system. The homologous series of n-alkanes is used as the reference backbone. Each member of the series represents a macroscopic system of identical particles (the n-alkane molecules) and the particles of the system themselves represent sub-systems of i uniform structural units. At room temperature systems in all physical states occur among the series of n-alkanes.
6.2 Interaction model As mentioned in the introduction, the discussion starts from a macroscopic system composed of n>>l identical particles. Among the particles there exists an attractive interaction that is responsible for the formation of condensed phases. The particles on the other hand possess a certain degree of freedom of motion in any direction within the system, as required by the liquid state. Because no preferred distribution of particles can be assumed, the system seems on average to be totally homogeneous and isotropic. This leads to an essential simplification of the problem. The background process in all interactions is an energy exchange between the n particles of the system, which is related to a change in position of the particles by oscillation and/or translation.
162
Piritiger
6.2.1 Model assumptions The following assumptions apply to systems of n identical particles (molecules, atoms) that leave their chemical identities essentially unchanged. Above a certain number of particles in the system, the sum of all interactions on a single particle by the other particles of the system becomes independent of the number of particles. This allows identification of a macroscopic system by its specific properties. 1. The interactions between the n particles are based on an exchange of discrete values E, = d~,, of energies E relative to an unit amount E ~ , .The consequence of this exchange is a relative density of interaction energy qGn= ( l + ~ $ n ) "in form of a n-fold product with the limit value q, = exp(e,) for n+w. The exponential expression is assumed because (i) the exponential function represents a mathematical order of magnitude which is higher than that of any other power of E,, this means exp(E,)IEra +ffi for a > 1 and E, +ffi;
($it reaches a constant value, independent of the number of particles in a macroscopic system with n>>l. The relative density q, is again considered a starting point for additional dynamic processes occurring in the system. Self-diffusion of the particles is an example of such a process. Based on the same mathematical assumption (i), the magnitude of the diffusion coefficient D = D,,exp(q,) is derived as an exponential function of q, with an unit amount D,,. This assumption is further supported by many empirically established equations describing dynamic properties of macroscopic systems. 2. A common characteristic of all particles is their extension in space, which means they possess a finite volume surrounded by a surface with area A . This area is equivalent to A for a surface of revolution which equals the product of the length of a meridian y and the length of the path of the center of gravity of y when y is rotated through the angle 211 (the theorem of GuldinIPappus):
The common function of all particles, independent of their specific structure is the ratio AIY = 2 7 ~The amount of energy transferred from one particle during an interaction step (see assumption 1 ) can now be written as E, = E: + a = 211 + a, where a is a specific parameter of the system and E: = 211 is defined as the relative reference exchange energy. 3. Mathematically, the interaction process is assumed to be an exchange of energy between n particles and can be treated as a permutation. Both the n particles and their n starting positions are labeled with the natural numbers 1, 2, ..., n. The whole process of energy exchange can now be understood as a result of n! consecutively occurring individual interaction steps. Each individual step represents a transport of one energy quantum from one partide to another and is interpreted mathematically as one change of places between the two particles. The total number of such place exchanges equals n!. The relative number, pI1,of exchanges related to n! in which n o particle remains in its starting position is then: Pn
=
I
1
-3!
+ .... + (-1) n 2l
;
lini pn = pc = 1 e
n--x
(6-7)
Prediction o,f diffiision coefficients in gases, liquids, amorphous Jolids .__
163
The limit value p e = l/e for n>>l is designated as the maximal probability of a place exchange in a macroscopic system. With these assumptions a common characteristic of all macroscopic particle systems can be expressed as qr = exp(e,) = exp(2n + a) (assumptions 1 and 2). However, taking into consideration a diminution of E, which is proportional to the maximum probability p e of place exchange (assumption 3), the value qr = exp(e,p,) = exp[(a + 2x)/e] = ea/ee2n/r= C 1 ’ e becomes ~ the specific relative density of interaction energy for a system where w = grde and C1le= e(d‘’. A special case occurs whenever the II particles are molecules from a homologous series of chemical compounds, e.g. n-alkanes. In such a case the specific parameter C can be enlarged into C = C0(l+2x/i)’, where i represents the number of carbon atoms in an unbranched alkane chain and C1Ir= C0”c’(1+2x/i)de = Kwi.
If a specific property f(i) of the macroscopic system can be correlated with qCiin form of a direct proportionality, than a simple dimensionless relationship between the values of this property for two members i and k of the homologous series results from Eq. (6-8):
The number w = eZde derived from the three assumptions of the model is the common limit value of the two power sequences:
These power sequences, designated as interaction functions, represent the mathematical backbone of the model described in this chapter.
164
Piringer
6.3 Prerequisites for diffusion coefficients 6.3.1 Critical temperatures of n-alkanes The critical temperature may be considered to be a measure of the intensity of interaction between the n particles of a system, as produced by van der Waals forces. Although the critical temperature for n>>l is practically independent of the number of particles, there exists a possibility for estimating the influence of the number of i structural subunits composing a particle based on the value of the critical temperature of a macroscopic system. Critical temperatures are especially suitable for the comparison of numerical values within a homologous sequence because at these temperatures the systems are in corresponding states. If Tc,iand Tc,kare designated the critical temperatures of two different n-alkanes containing i and k carbon atoms, we may tentatively let the dimensionless ratio Tc,i/Tc,kbe equal to the ratio of the two corresponding interaction functions w ~ and , ~ Wk,e in Eq. (6-9): (6-11)
Experimental values for the critical temperatures of n-alkanes are known up to eicosane (i=20) (Reid et al., 1987). For longer molecular chains the experimental determination of the critical temperature is not possible with sufficient accuracy due to the onset of thermal decomposition. By means of Eq. (6-11) it is possible to calculate, starting from each experimental value corresponding to i carbon atoms, a limit value T , , , (for k +co) (Table 6-1). Due to the fact that the terminal methyl groups in the initial members of the n-alkane represent an important deviation from a system containing only methylene groups, it is more convenient to use alkanes having chains as long as possible for the determination of Tc,m.As seen in Table 6-1 these deviations become unimportant after i=9. This is because the individual Tc,mvalues are irregularly distributed for the 12 longest
800 -Y
.-
2
600 --
I
04 1
3
5
7
9
11
13
15
17
19
i
Figure 6-1: Critical temperatures of n-alkanes as a function of the number i of carbon atoms. Calculated values using Eq. (6-11) (-), measured values ( + ) and limit value, T, (- - -).
Prediction of diffusion coe,fficients in gases, liquids, amorphous solids ...
165
Table 6-1: Critical temperatures of n-alkanes. Number i of carbon atoms
TJK
T,,,/K
T,-T,,,
9
594.6
1039.1
-2.0
10
617.7
1036.8
4.6
11
638.8
1035.5
+0.7
12
658.2
1034.9
+1.3
13
676.0
1034.8
+1.4
14
693.0
1036.0
+0.2
15
707
1034.7
s1.5
16
722
1036.7
-0.5
17
733
1034.4
+1.8
18
748
1039.2
-3.0
19
756
1035.4
+0.8
20
767
1036.8
4.6
chains (i=9-20). The mean limit value obtained from Table 6-1 is Tc,x = T, = 1036.2 K. Figure 6-1 shows the estimated curve for TC,*from Eq. (6-11) using Tc,k = T, = 1036.2 K as well as the experimental values of T,,, for 15 i520. The remarkable coincidence between the ratios of the critical temperatures, T,,,/T, within the homologous series and the ratios of the corresponding values of the interaction function w,.,Iw supports the interpretation that this function is a measure of the energy density of interaction. Due to the translation and rotation of particles in the liquid state of a macroscopic system, the value of the interaction function may be assumed to be independent of the configuration of the particles within the system. Therefore, there is no need for data related to orientation. This is also valid for the i chainlike subunits of an alkane molecule. Due to the possibility of a free rotation of any of the i subunits around the bond axis with the neighboring subunits, a relative motion of segments of several subunits is also possible.
6.3.2 Critical compression factor The first term w l = (1+27t)'/' of the power series w, defined in Eq. (6-10) plays a special role within the interaction model in that it represents a perfect gas phase. If V,, p,, T , and R represent the molar volume of a compound, the critical pressure and critical temperature of the system and the gas constant, then the product prVn is reduced to l i w of the product RT, due to the interaction between the particles in the system. Taking into account an empty (free) volume fraction in the critical state, the critical molar volume is written as V , = wlVo. Consequently, a dimensionless critical compression factor, Z,, is defined using the following equation: (6-12)
166
Piringer
From a data collection with 349 experimental values for the critical compression factor (Reid et al., 1987) obtained with organic and inorganic compounds and elements, a mean value of Z , = 0.2655 is obtained with a standard deviation of o = 0.0346.
6.3.3 The entropy of evaporation Systems with comparable amounts of disorder are especially important for developing a common basis for relationships between diffusion coefficients. Such a comparable amount of disorder is generated when any liquid evaporates and becomes a gas. According to Trouton's Rule the entropy of evaporation has values around 85 JK-'rnol-l for many liquids at their boiling point Th at a standard pressure of 1bar. This rule was modified by Hildebrand (1915; Hildebrand et al., 1970).According to Hildebrand, the value of the molar entropy of evaporation, ASv, for many substances is nearly the same at temperatures where their molar vapor volumes are equal to the standard value of 24.8 dm3 mol-' at 25 "C.The validity of this rule extends over boiling points ranging over three orders of magnitude and for classes of substances as different as monoatomic noble gases, high boiling metals and compounds with polyatomic molecules with complex structures. The deviation from the mean value of 84.9 JK-'mol-' does not exceed 1.5 JK-'mol-' with few exceptions when using the Hildebrand correction. As a conclusion from the Hildebrand/Trouton Rule, the definition of a standard vapor phase in a standard state with a well known amount of disorder can be made. This definition can be used as a starting point for modeling diffusion coefficients of gases and liquids. The change in entropy AS for a reversible isothermal expansion of an ideal gas and therefore V2W1= from its initial volume Vl to a volume Vzis AS = R In(Vz/VI) exp(AS/R). By setting V2/VIequal to the ratio between the molar volume V; = 24.8 dm3 mol-' of an ideal gas under standard conditions ( T = 298.15 K , p = 1 bar) and assigning a volume V i to one mole of a liquid at Th. then VE/V: = exp(AS,/R) = exp(AHv/RTh).Where A H v stands for the molar enthalpy of evaporation at the Hildebrand temperature, Th,and AS, is the molar entropy of evaporation. By using ASv = 84.9 JK-'mol-' the value V ; = 0.91 cm'mol-' is obtained. An interpretation of the Hildebrand/Trouton Rule is that this "free" volume, VL,allows for the freedom of movement of molecules (particles) necessary for the liquid state at the temperature Th.The explanation of the constant entropy of evaporation is that it takes into account only the translational entropy of the vapor and the liquid. It has to be pointed out that VE does not represent the real molar volume of a liquid, but designates only a fraction of the corresponding molar volume of an ideal gas V& derived from the entropy of evaporation. The real molar volume VLof the liquid contains in addition the molar volume occupied by the molecules Vo. As a result the following relations are valid: V L= V i + V ,and V , = V&+ V,. However, while V;*< V , and V Lis practically independent of the pressure, V , << VE in the gaseous phase. Only in the critical phase does V,/V, = 1 and the entropy difference between the two phases vanishes.
Prediction of diffiision coqfFcieritsit7 gases, liquids, amorphous solids ...
167
6.3.4 The reference temperature The first term, w ~ ,of~ the , power series w ~represents , ~ a macroscopic system of interacting monoatomic particles in the model. In the gaseous state even polyatomic molecules are considered to behave like monoatomic particles. In gases the difference w I - w ~ , ~ is interpreted to be a pure translational contribution to the energy of the system and can therefore be related to its temperature. In order to establish a connection between the difference wI-wl,, and Sl units let us start with n = 1000 mol of hypothekg in a volume V=l m'. tical particles with the atomic mass unit u = 1.66054 x This system with N = nNA = 1000(m01)~6.0221410~~ (mol-') particles defines the mass unit of Nu = 1 kg. The total energy of the system is E = Cniejwhere nj particles are in the state with energy E ~ Using . the Boltzmann distribution and E = (N/q)CEiexp(-Pq) with p=I/kT, the following relationship between the internal energy of the system and is postulated to be: the two terms wI and wl,, (6-13) With the translational partition function 9 = VIA3and h3= h3/(2nrckT)3'2a value for the temperature T = 2.98058 K results, when using the values for N,V,u, the Planck constant h = 6.62608 x Js and the Boltzmann constant k = 1.38066x JK-I. The self diffusion of particles and the entropy of the system are both a result of random particle motions. With the Sackur-Tetrode equation the molar entropy, S,,, of the above system can be calculated at temperature Tand pressure p : (6-14) As shown in the previous section a common feature of all systems in the liquid state is their molar entropy of evaporation at similar particle densities at pressures with an order of magnitude of one bar. Taking this into account a reference temperature, T,, will be selected for systems at a standard pressure, p o = lo5 Pa = 1 bar, having the same molar entropy as for the pressure unit, p,, = 1 Pa at T = 2.98058 K. As can easily be verified, the same value of molar entropy and consequently the same degree of disorder results at p if a one hundred-fold value of the above T-value is used in Eq. (614). This value denoted as T,, = 298.058 K = T, is used as the temperature reference value for the following model for diffusion coefficients. The coincidence of T, with the standard temperature T = 298.15 K is pure chance. With Tv a reference molar volume of gas, Vg = RT,,/po = 24.782 dm'mol-' is defined, which by chance is very close to the value of the standard volume VG = RT"/p" = 24.79 dm'mol-'. Assuming that the molar volume VL discussed in the previous section is a result of interaction between the particles in a condensed macroscopic system, a reference molar volume, V,W,is defined using the reference volume Vg and the limit value w of the interaction function w, for a macroscopic system (n-m):
svll -
exp(%)
= e x p ( F ) = ew = 24078.88
(6-15)
168
Piringer
VW , = Vg/ew= 1.029 cm3mol-'. The product w R = 10.0891 . 8.31451 = 83.8858 JK-' mol-' defines a reference entropy of evaporation and lies within the limits of deviation from the values of the Hildebrand entropy of evaporation.
6.4 The diffusion coefficient The following discussion starts with macroscopic systems in the gaseous state. However, its main distinction from the kinetic theory of perfect gases lies in taking interactions between particles into consideration from the start. The difference from the treatment of perfect gases is accounted for by two parameters, the critical temperature, T,, and the critical molar volume, V,. All particles in the gaseous phase are treated as monoatomic particles. Liquid systems occupy a special place between gaseous and solid phases. The high mobility of particles in a liquid and the values of diffusion coefficients falling in a narrow range supports the assumption of a free volume of about 1 cm"mo1-' (see Section 6.3.3) as a prerequisite for the manifestation of the typical properties of a liquid phase. The solid phase is considered to be an amorphous pile having a maximum disorder amongst the particles. Such a close-packed assemblage has some similarity with a liquid. But an essential difference from liquids lies in the absence of the supplementary free volume. An amorphous solid phase with interacting particles having a certain degree of mobility is considered to be essential for the diffusion process in plastic materials. In all aggregate states in this model, diffusion is considered to be a consequence of interactions between the particles that are in conformity with the first assumption of the model. This means the diffusion coefficient can be described as an exponential function of a relative density of interaction energy 4,.
6.4.1 Diffusion in gases At constant temperature the ratio D G , 2 / D ~ of, the ~ diffusion coefficients in a gas at two states 1 and 2 equals the ratio V2/Vl of the system volumes at the two states. Then together with the first assumption a starting point for modeling diffusion coefficients will be the relation DG,Z= (V2/VI)D,exp(q,) with the unit value D,, = lm2/s and q, = wI for a perfect gas. By selecting Vl= lo5 VE at p u = 1 Pa as a reference volume the following equation results for a self-diffusion coefficient, DG in a perfect gas: (6-16) This equation is typical for ideal gases in which neither an interaction term in form of activation energy nor the volume of the diffusing particles are considered. At p = 1 bar and T=O"C for example, DG = 1.36 cm2/s is obtained using Eq. (6-16) compared with 1.4 cm2/smeasured in He (Landolt-Bornstein, 1969). For real gases two additional terms in the exponent of Eq. (6-16) must be introduced:
Prediction of diffusion cocfficients iri gases, liquids,aniorphous solids ...
169
1. A molar activation energy EA of diffusion is defined as the product EA = wl,,RTc, with the critical temperature, T,, of the system. This definition takes into account the connection between the interaction terms of the model, w, and w,,, and IS units, as shown in section 6.3.4. At the critical temperature, T,, a pure translational amount, wI-w/,e,of the relative energy density is responsible for the magnitude of DG. 2. The second term takes into account the size magnitude of the diffusing particle. Let A , = V0213 m2mol-' be the molar cross-sectional area of the diffusing particle. When moving through the system a particle with this cross sectional area must overcome the force exerted on it by the other particles in the system while they are moving about in a disordered fashion. The magnitude of this force F divided by the unit area A,, = 1 m2 to which the force is being applied defines a pressure, p = F/A,. The product pA,,,d = (A,/A,,)Fd = Enl,AJ mol-' represents the necessary molar work to overcome the resistance of the matrix by moving A,,, along the distance d in a direction perpendicular to it. Referred to the corresponding work for moving A , along the same distance, E u , A = Fd J, we get E , n , A / E , , = ,~ = A,/A,, = A,n mol-'. On the other hand, the pressure p can be expressed as p = m(N/V)
170
Piringer
first approximation. Examples of such molecules are N2 and 0 2 . In Table 6-2 the selfdiffusion coefficients of noble gases at 1 bar, calculated with Eq. (6-17) are compared with experimental values (Kestin et al., 1984). Helium behaves at T >> T, like a perfect gas (Eq. 6-16) without interaction ( T , = 0) and atomic size (Vc= 0). Molecular hydrogen has the same behavior. Table 6-2: Self-diffusion coefficients of noble gases at 1 bar.
TJK He
Ne
Ar
Kr
Xe
5.19
44.44
150.8
209.4
289.7
Vc/(10-' m3mol-') T/K 5.74
4.16
DG/(cm* s-')
50
0.093
0.089
100
0.21
0.29
200
0.44 (1.00)"
0.92
300
0.67 (1 SO)'
1.82
0.021
0.021
50
7.49
9.12
11.84
*) Values obtained for a perfect gas with T,
DG/(cm2s-I) calc.
=0
exp.
100
0.11
0.08
200
0.34
0.27
300
0.59
0.53
200
0.083
0.087
300
0.21
0.19
373
0.32
0.28 0.045
200
0.040
300
0.12
0.10
373
0.20
0.15
300
0.058
0.058
373
0.1 1
0.09
and V, = 0.
The mutual diffusion coefficient, DG,AB= DG,BAfor a binary mixture of A and B is and V , A B defined by Eq. (6-18), using the critical temperature T c , A=~ XAT,,A+XBT~,B = (VC,,+V,,8)/2,where X A and XB are the corresponding mole fractions:
(6-18) Examples of diffusion coefficients calculated with Eq. (6-18) are summarized in Table 6-3 where they are compared with corresponding experimental values (Reid et al., 1987). Diffusion coefficients of water and hydrocarbons in air are especially important parameters in mass transfer processes between plastic materials and the atmospheric environment.
Prediction of diffiision coeffiicirrirsin gases, liquids, anzorphoirs solids ...
171
Table 6-3: Diffusion coefficients of water and n-alkanes in air at 1 bar. Compound Water
T/K
DG,BA/(cm2 SKI) calc.
DG.BA/(cm2 s8) exp.
273
0.21
0.22
288
0.23
0.24
298
0.25
0.25
308
0.26
0.26
318
0.28
0.28
Pentane
298
0.106
0.084
Hexane
298
0.089
0.080
313
0.098
0.085
333
0.109
0.096
293
0.073
0.067
313
0.083
0.077
293
0.062
0.064
313
0.071
0.071
333
0.079
0.078
293
0.053
0.060
313
0.061
0.062
333
0.068
0.071
313
0.052
0.060
333
0.059
0.064
Hcptane Octane
Nonane
Decane
The following example illustrates the mode of calculation for obtaining the diffusion coefficient DC;,AB of water (B) at low concentrations in a gas phase which is mainly composed of air (A). Air as the gaseous matrix is considered a homogeneous mixture for which
T c ,= ~ xo2 . Tc,02+ X
+
N .~T c , ~= 20.2 . 154.6
Vc.= ~ (Vc,02 V C , ~ /2 2 ) = (73.4E-6
+
+ 0.8. 126.2 = 131.88K and
89.8E-6)/2
= 81.6E-6
m3mol-'.
The critical molar volume of water is V c , R= 57.1E-6 m3 mol-I. With these values V,~,, = (81.6E3-6+57.1B-6)/2= 69.35E4 m3mol-'. Together with T c . and ~ Eq. (6-18) the calculated values in Table 6-3 for the diffusion coefficients of water in air were obtained. The diffusion coefficients DG,ABof small amounts of n-alkanes in a matrix of air are calculated in the same manner as shown above for water. But in the case of the homologous series of n-alkanes a simplification is possible because the critical molar volume, V,,,, for a member of the homologous series can be obtained with good approximation from the corresponding molecular weight, M,.,,using the relation V , , = 4.238E-6. M,,,, as shown later in Eq. (6-25).As an example, for n-octane V , , = 114.4.238E4 = 4.83E4 m3 mol-'. With V L , A = 81.6E4 for air and V<,AB = 2.824E-4 m3 mol-' together with Tc.A and Eq. (6-18) the value D G , J A = 0.062 cm2s-' at 20 "C and 1 bar is obtained.
172
Piringer
The tracer diffusion or intradiffusion coefficient, DL,BA,for the compound B in a mixture of A and B can be a function of composition, like the mutual diffusion coefficient. But instead of V,,,, for mutual diffusion, Vc.Bis introduced in Eq. (6-18).
6.4.2 Diffusion coefficients in the critical state Equation (6-17) can be easily adapted for the critical state, if p is substituted with the critical pressure, p c , obtained with Eq. (6-12) and if w I in the exponent is substituted with wI,e This takes into account the absence of a pure translational energy contribution in the critical state. On the contrary, an additional negative term, the critical compression factor Z , = -w,/w, is introduced in the exponent, taking into account the decrease in diffusion velocity caused by attraction between the particles. As a result the following equation gives the coefficient of self-diffusion in the critical state:
6.4.3 Diffusion coefficients in amorphous solids A reference equation Let us now consider a macroscopic system in an amorphous state above its glass temperature. The particles of the system are n-alkanes with i >> 1 carbon atoms in the molecular chain. Let us first consider the theoretical case with one single macromolecule of infinite length that forms a polymethylene chain in the shape of a disordered coil. Due to the possibility of free rotation of any of the methylene subunits around the bond axis relative to the neighboring subunits, a relative motion of segments of more subunits is also possible. In the following a reference equation for the diffusion coefficient of a n-alkane with a number i of carbon atoms in a hypothetical infinite chain will be derived in manner analogous to that for gases. If in the first approximation we neglect the existence of activation energy, EA, for the diffusion process and the volume and mass of the diffusing solute, a ratio of diffusion coefficients D2/D1= exp(q,) = exp(w) = exp(wR/R) = exp(AS,/R) in two states of the system is the starting point. This conforms to the first assumption of the model where the amount 0 2 is related to a value D I for an initial state. This ratio is a measure of the disordered motion of the methylene groups, with a corresponding increase of the molar entropy ASw = wR, resulting from the interaction between these groups in the polymer matrix with the relative density of interaction energy, qr =w. One mole of polymethylene is defined as one mole of methylene groups, -CH2-. The disordered motion of the methylene groups providing the value D2 related to D I is assumed to be analogous to the reversible expansion in a gas with the same change in entropy ASw In comparison with the behavior of a gas, the expansion of this system is neglected and the ratio V2/Vl z 1.For the reference equation D1 = D, = 1m2s-I. In a second step, a molar activation energy, EA, of the motion of the methylene groups in the polymethylene chain is introduced. This activation energy EA = wRT, = 10.089 . 8.31451 . 1036.2 = 86.923 kJ mol-I is defined as a magnitude proportional to
Prediction of diffusion coefficients in gases, liquids, amorphous solids ...
173
w (analogous to wI for gases) and to the limit value of the critical temperature T, = T,,, = 1036.2 K in the homologous series of n-alkanes. In this way D2 = D,, exp(wE,/RT). The next step takes into account the diffusing solute as described for the gaseous state. Due to the practically immobilized matrix composed of macromolecules, the solute is considered to be a tracer for which only its critical molar volume, Vc,i,must be considered. In the special situation of a n-alkane with repeating -CH2- groups in the molecular chain, a constant value of the ratio VJM,.; can be expected for the homologous series excepting the first few members. The first few members deviate from this substructure because of the presence of the two -CH3- endgroups. For the n-alkanes with i = 5-17 a mean value V J M , ; = 4.2385 x lo4 m'mol-' is obtained (Reid et al., 1987). With this value ~ O O O ( V , , ; / W = ~lOOO(4.2385 )~~~ x l0-h M , ; / w , ) ~ /= ~ 0.1351 Mf,i3results. Finally, analogous to the gas phase an equation for the diffusion coefficient, D,,,of a n-alkane with i carbon atoms in an amorphous polymethylene is obtained (Brandsch et al., 1998): Dp,i
= D,
[
exp w - 1000($)
213 -
F] D, exp (w =
-
213 0.1351M,,i
-
(6-20)
Equation (6-20) can be used as a reference equation for all polymers. It represents a theoretical construction resulting from an asymptotic correlation and the assumption of an infinite chain composed of methylene groups representing the amorphous polymer matrix. Diffusion coefficients of n-alkanes in polyethylene While w = Ap stands for the theoretical structure of polymethylene, other characteristic Ap-values can be obtained for other polymers or solids depending on their specific structure. Nevertheless, the remaining two terms in the exponent of Eq. (6-20) can be held unchanged for polyolefins and alkanes. For other diffusing compounds the corresponding critical molar volumes would be more appropriate than the molecular weights. Taking A P to be a characteristic parameter of the polymer which must be determined experimentally, the following more general equation for the diffusion coefficient Dp,ican be used (Brandsch et al., 1998): Ap
-
0.1351M,.i 213
-
(6-21)
The factor 0.1351 in the exponent of Eq. (6-21) can be used as an acceptable approximation for most hydrocarbons and other solutes with low polarity. Comparison of calculated and experimental data The diffusion coefficients of n-paraffins with 12 to 22 carbon atoms in high density (HDPE) and low density polyethylene (LDPE) have been measured by a permeation method (Koszinowski, 1986). Methanol (MeOH) and ethanol (EtOH) were used as contacting liquid phases which minimized interaction between these polar solvents and the nonpolar polymers. No interaction was observed over the investigated temperature range of 6 to 40 "C for both solvents.
4,
0
-
-10.0 --
... p
.
- -Ap=8,8 -
Ap=lo.o89
-10,4 T
Figure 6-2: Logarithm of diffusion coefficients of n-alkanes in polyolefins at 23°C as a function of the relative molecular mass.
Figure 6-2 contains the measured values of the diffusion coefficients from HDPE and LDPE at 23 "C and the calculated curves obtained with Eqs. (6-20) and (6-21) for the corresponding range of masses. The measured diffusion coefficients are in good agreement with the calculated values obtained with Eq. (6-21) using A P =8.8 for HDPE and AP = 10.6 for LDPE, respectively. The most important finding is the close agreement of experimental values with the M:,y-dependence in the exponent of Eq. (6-21) and the reference Eq. (6-20) with the theoretical value Ap = w = 10.089. Figure 6-3 shows the temperature dependence of the diffusion coefficients obtained with i = 12 to i = 22 in LDPE. Comparison of experimental data with the corresponding curves obtained with Eq. (6-21) and AP = 10.6 for i = 12 and i = 22 shows again a reasonable agreement. This result is used as a proof for the activation energy ( E A ) order of magnitude used in reference Eq. (6-20). The value of 86.923 kJ mo1-l is of the same order of magnitude as that for bimolecular reactions in solution.
I -8 --
-. 6
3.1
u)
v
0
-9
--
-
--- ---
A
x
0
c12 C14 C16 C18 c20 c22 cak C12 calc C22
a
O cn
2 -10 --
-1 1
4
3,15
3.35
335
l/r (10001K)
Figure 6-3: Logarithm of diffusion coefficients of n-alkanes in LDPE as a function of temperature.
Prediction o f rfiffiisioncoefficienls in gases, liquids, amorphous solids ...
175
A general equation for plastics In the general case of a solute B in a plastic matrix P the parameter AP is a function of temperature and produces a more or less significant deviation from the activation energy, E A = 86.923 kJ mol-' in reference Eq. (6-20). Consequently we can write: A p = Ap'--Zp/T,with the athermal, dimensionless number Ap' and the parameter z p with the dimension of a temperature, respectively. Both values, Ap' and - z can ~ be obtained from two diffusion measurements at different temperatures, using a reference solute B in matrix P (see Chapter 15). The specific contribution of B in the DcB-value can be taken into account by two supplementary dimensionless parameters. While ps,B stands for a structural difference of B in comparison to a hypothetical n-alkane with the same relative molecular mass Mr.B, the number p ~ =p p:f + &/T represents an interaction increment between B and P, due to the different polarities of the solute and plastic. This interaction is generand p s p can be considered as ally a function of temperature. The two parameters, vs~B relative mass increments (positive or negative) which vanish in the reference system of n-alkanes in polymethylene. If the diffusion coefficient, DKB, is obtained by measuring the mass transfer of B from P into a liquid phase L in contact with the plastic material, more or less strong interactions can occur between the two phases. If the polarities of the plastic material and the liquid phase are similar, swelling of the plastic occurs and the direct consequence of this interaction is an increase of the DRB-values.This process is also a function of temperature and, taking it into account, two supplementary increments, AL for interaction between P and L and p B L for the interaction between B and L are introduced, respectively. Collecting all these parameters, the following general equation can be written: D P ~ B = DU
2/3- 10454 (6-22) ( + AL - 0.1351 ( M ~ . B+ L.B + pBp + pBL) 7)
~ X PAP
with Ap = Ap'-TpIT ; AL= AL'--zL/T ;
p ~= p p:p
+ pgp/T ;
+ piL/T.
~(B= L P ~ L
Due to the temperature dependence of the parameters A A A L , P E P and P E L , an apparent activation energy, E A , results which deviates more or less from the reference value of 86.923 kJ mol-'. An open question remains over the influence of solutes with high molecular masses on the DpB-values. Measurements were performed using bilayers of polyethylene and polypropylene, consisting of a thin (0.1 pm) film of deuterated polymer atop a thicker (1-2 pm) film of the corresponding hydrogenated polymer (Gel1 et al., 1997). The bilayers were then annealed for appropriate times and temperatures, permitting diffusion to develop a concentration depth profile of the deuterium nuclei. The deuterium depth profile was determined by the forward recoil spectrometry (FRES) technique. The entangled polymer coils show a remarkable diffusion rate, which is orders of magnitude higher than predicted with Eq. (6-21). For diffusion in amorphous polymers at temperatures above their glass point, Tg, one can assume a behavior with some analogy to a liquid. On the other hand the Stokes-Einstein Eq. (6-4) for liquids was derived under the assumption that the diffusing particle is much larger in size than the matrix particles. If we let the matrix be a
176
Piringer
macroscopic system of identical particles composed of -CHZ- groups and the diffusing solute is the whole entangled macromolecule, then the system fulfills the assumption of Eq. (6-4). The decrease of DeB with increasing M,.Bin this equation is much slower than in Eq. (6-21). In order to cover the whole range of molecular weights for solutes in a polymer matrix we can start with Eq. (6-21) and introduce a supplementary positive term, aM,B: Ap - 0.1351MfjB3
+ aMr,B - 10454/T)
(6-23)
A comparison of predicted and measured values of diffusion coefficients for solutes with a large range of molecular weights in polyolefins is shown in Chapter 15 and allows an empirical selection of the U-value.
Diffusion ofparafins in paraffin
Reference Eq. (6-20) for an infinite chain of covalently bonded methylene groups can be considered to be an asymptotic limit for the homologous series of n-alkanes. By substitution of w into the exponent of Eq. (6-20) by the corresponding term, w ~ , ~ , which represents a matrix composed of a paraffin with i carbon atoms, an equation for the diffusion coefficient Ds,ki for trace amounts of a paraffin with k carbon atoms results:
= D,
exp(wi,e - 0.1351M;,f
-
~
%).
i
~
(6-24)
from using the limit value T, = 1036.2 K and the molecular weight, k f r , k , of solute k or its critical molar volume, v , , k . For self-diffusion i = k and for solutes with structures significantly different compared to paraffins, the critical molar volume instead of the molecular weight is preferred. Diffusion coefficients in liquids
With the exception of the super cooled region below the melting point, the liquid state of a substance occurs between its melting point and its critical state. Correspondingly, an equation of diffusion coefficients for liquids is based on Eqs. (6-19) and (6-24) representing these limits. Starting with the homologous series of n-alkanes as a reference structure series and the entropy of evaporation discussed in section 6.3.3, the development of an equation for the liquid state is possible with the following steps: With Eq. (6-17) a value of the self-diffusion coefficient, D T l for the first member of the reference series is calculated using the critical temperature TC,,= ( W ~ , ~ / W ) T , (Eq. 6-11) and the relation: (6-25)
Prediction of diffusion coefficients in gases, liquids, amorphoits solids ...
177
This relation is used for the reference series in Eq. (6-20), with the value 0.1351 Mf,? = 0.1351 . 162'3for the first member of the series. At the reference temperature T, and the standard pressure of 1 bar, the value D P l = 1.42735 x m2s-' is obtained with Eq. (6-17) for the gas phase. This value is a reference number and not the experimental value found for methane. Taking into account that the same disorder occurs for liquids in equilibrium with their vapor phases having the same molar gas volume, a reference diffusion coefficient, D!,l = D z l / e w = 5.9278 x lo-"' m2s-l is obtained from the reference diffusion coefficient in the gas phase. In the next step, Eq. (6-24) with i = k is used to calculate a temperature, TIo,for which the self-diffusion coefficient, D,,, is equal to the reference value DO,.,: (6-26)
Df,, is a first approximation and is obtained only if T? = T,. Consequently, a correction must be introduced which accounts for the deviation of TP from T, This corrected value, denoted D f , , = (T,/T?)Df.,defines the lower limit of self-diffusion coefficients for a paraffin i at T?. The upper limit of the self-diffusion coefficient in the liquid phase is obtained with Eq. ) T , the critical pressure, p,;=(RT,I (6-19) at the critical temperature, TC,;= ( W ~ , ~ / Wusing VC,;). ( w J w ) from Eq. (6-12) in combination with the Eq. (6-25) for the n-alkane series: & 4 . 2 3 8R 5 . 1 0 - 6 ~ ~ w, r,i.D
D C J. - T~
= 6.3939.
10-9exp(-$
-
exp(-?
0.1351M:%i3)
-
0.1351M:,f) (6.27)
It can be assumed that the self-diffusion coefficient DL,; at a temperature T between T? and Tc,;follows the exponential function D = ae-"'. Collecting all results from the above steps and writing Dt,l = a exp(-h/Tp) and D , ; = a exp(-blT,,J, the following equation is obtained for the diffusion coefficient DL,;:
~
~= a , exp( i -
+)
(6-28)
with
Taking into account that, for the reference homologous series of n-alkanes the relative molecular masses of the member i in the series is M,,= 2 + 14 i, the self-diffusion ~ be calculated with Eqs. (6-27) and (6-28). This can be done using coefficient D L , can only two values based on experimental results, the limit value of the critical temperature, T,, and the mean value for the ratio, Vc,,/Mc,. Table 6-4 shows a comparison between experimental (Landolt-Bornstein, 1969) self-diffusion coefficients and calculated values obtained with Eq. (6-28). A mutual diffusion coefficient, DL,,k,can be defined in the same manner as for gases + vc,k)/2 and P c , i k = x i ' p c , ~-k x k Pc.k. with Tc.rk = X I TC,If X k Tc.k and Vc.rk (vc,~ '
'
178
Piringer
Table 6-4 Self-diffusion coefficientsof n-alkanes. Alkane with i carbon atoms
T/K
D ~ , ~ / ( Icm2 o - ~s-') calc.
Heptane
298
3.23
3.10
Octane
298
2.28
2.75
333
3.8
3.6
298
1.67
1.70
333
2.8
3.0
Nonane
t1~,~/(10-'cm2 s?) exu.
298
1.28
1.31
333
2.2
2.5
Dodecane
333
1.4
1.5
Octadecane
323
0.52
0.46
Dotriakontane
373
0.42
0.30
Decane
In Table 6-5 the mutual diffusion coefficients of a binary mixture of n-heptane and n-hexadecane at 25 "C are calculated for different molar fractions of the solutes and compared with experimental values (Landolt-Bornstein, 1969). Table 6-5: Mutual diffusion coefficients of a binary mixture of n-heptane and n-hexadecane at 25 "C and different molar fractions x. XI6
0.0056
0.1064
0.2024
0.3934
0.5821
0.7920
0.9761
x7
0.9944
0.8936
0.7976
0.6066
0.4179
0.2080
0.0231)
DL.ij talc./( 10-'cm2s-')
1.72
1.59
1.45
1.18
0.95
0.74
0.58
DL-,, exp./(I0-'cm2s-')
1.78
1.59
1.45
1.24
1.07
0.895
0.76
Tc,7= 534.58 K, Tc,,6= 721.68 K, pC,,= 27.4 bar, pC.l6= 14.1 bar, Vc,7= 4.2378E-4 m3 mol-'. Vc,lb= 9.577E-4 m3 mol-'
The tracer or intradiffusion coefficient, DtTkiof an n-alkane k in a solution of n-alkanes i and k at temperature T can be calculated with Eq. (6-28) in two steps: first, the ratio D,?k,/Dzi, for mutual diffusion at T and T,, is calculated. In the next step the tracer dif usion coefficient D$, at the reference temperature T,, is calculated using M , . k instead of M,; in Eq. (6-26) and in the exponent of Eq. (6-27). The corresponding values for TZj and Dc,kiare then used for bki and ak; in Eq. (6-28), respectively. Finally we obtain: (6-29) In order to generalize Eq. (6-28) for any organic solutes, the self-diffusion coefficient DL.Aof a compound A can be calculated in the following manner: (6-30)
with
Prediction ofdiffiaion coqfficierits in gases, liquids, aniorphoirs soli~ls__.
179
and 1
I n D t , l + 1O3
1
(%)
2'3).
The product w . T c , A in the above relation results from Tc.,= T,(wj,,/w) if the critical temperature, T L . , A ,of liquid A, which is not a member of the homologous series, is used instead TC.;.In this case wj,, in Eq. (6-24) is substituted by (TC.,A/TC)w. If no value for the critical molar volume Vc.,Ais available the use of the relative molecular mass, MKA, is an acceptable approximation. In this case Eq. (6-25) has to be used for substitution of Vc,Aby MGAin Eq. (6-30). The mutual diffusion coefficient, D/,,,,R, in a mixture of A and B is defined in the ~ X A . Tc.A + x B . T C ,and ~ V,:, = (Vc.~ + same manner as for n-alkanes, with T c , A = vc,B)/2 and P c , A B = X A ' p c . A + X B 'Pc.B. As shown above for the homologous series for n-alkanes the tracer-diffusion coefficient, Df7BA,of a compound B in the solvent A at temperature Tis obtained within two steps: first the ratio of mutual diffusion coefficients D:,,,/DT". L , A B i ~calculated using Eq. (6-30).Then D;TBAis calculated at the reference temperature T,, using Vc.Binstead of Vc..Ain Eq. (6-30). Finally the value of D;,7jjAresultsas: (6-31) For B = A, the tracer diffusion coefficient equals the self-diffusion coefficient, D:TBA= Dl,A. In Table 6-6 the self-diffusion coefficient of water and some diffusion coefficients of organic solutes in water at infinite dilution calculated with Eq. (6-31) are compared with experimental values (Reid et al., 1987). The experimental value for sucrose is from Cussler (1997). If no value for Vc,B is available, again M Kcan ~ be used as a reasonable approximation, using the substitution 103(Vc,~Iw~)2'3 = 0.1351 . M:,$ (relation 6-25) in Eq. (6-30). With water as the liquid phase A, an upper limit for the mass M G Bof a diffusing solute B at infinite dilution is reached at M G B= 212, because above this value bHA in Eq. (6-30) changes its sign. As mentioned before, for solutes with significantly higher sizes than the sizes of the matrix particles, the Stokes-Einstein equation (6-4) can be used. In this equation the solute radius a is used which can be correlated with V,,,li3 and MKBIi3. Taking this into account in the case of aqueous solutions, the diffusion coefficient D / . , B A for solutes with Mr,B> 212 can be estimated with the following equation:
(z) I /3
'L.l3A
= DL.212A
, with
> 212
(6-32)
D[,2,,A is calculated with Eq. (6-31) using Mr., = 212. In Table 6-7 diffusion coefficients of high molecular solutes in water calculated with Eq. (6-32) are compared with experimental values (Tanford, 1961). With the homologous series of n-alkanes, such an upper limit, Mr.,nn.rk, for the relative molecular mass of a trace paraffin k in a solution of paraffin i is obtained for each member of the series. Consequently, an analogous equation to 6-32 can be written for the series:
180
Piringer
Table 6-6: Diffusion coefficients in water at infinite dilution.
TIK
Solute
DITBA calc. cm2 s-'
Water
D&
exp.
% error
lo-' cm2 SC'
298
2.24
2.13
+ 5.4
273
1.41
0.97
+45
- 28
373
6.24
8.65
275
1.27
0.85
+49
333
3.20
3.55
-
Carbon dioxide
298
1.95
2.00
- 2.7
Propylene
298
1.50
1.44
+
Methanol
288
1,52
1.26
+20
Ethanol
288
1.32
1.00
+32
Acetic acid
293
1.42
1.19
+20
Ethyl acetate
293
1.10
1.oo
+10
Aniline
293
1.13
0.92
+23
Diethylamine
293
1.07
0.97
+10
Pyridine
288
I .09
0.58
+88
Ethylbenzene
293
0.94
0.81
+I7
Methylcyclopentane
275
0.79
0.48
+64
293
1.04
0.85
+22
333
1.72
1.92
- 10
298
1.55
1.34
+16
348
3.02
3.67
-18
298
0.5247
0.5228
+ 0.4
Methane
Vinyl chloride Sucrose
Table 6-7: Diffusion coefficients of macromolecules in water at 20°C. Solute B exp. Sucrose
342
5.03
4.59
Ribonuclease
13700
1.47
1.19
Lysozyme
14100
1.46
1.04
Serum albumin
65000
0.88
0.59
Haemoglobin
68000
0.86
0.69
Urease
480000
0.45
0.346
Collagen
345000
0.50
0.069
Myosin
493000
0.45
0.116
9.7 4.2
Prediction of diffiision coefficients in gases, liquids, nmorphous solids ... DL.ni T --D TL.imxki (Mr.'llaxk)
'I3, with Mr." > Mr,maxk
181 (6-33)
DI,~~,~~~
where is calculated with Eq. (6-29) using M r , k = for which bk reaches a minimum positive value. With increasing values of the relative molecular masses of the solvent, M,;, the corresponding maximum value Mr,,,taxk is approximately M , = (~~,,/0.1351)"~, a value which results from Eq. (6-24) for w ; , ~= 0.1351M,.k2'3. For i +M, w ; , ~+ w and M K m n x k = 645. Above this molecular weight a significant slower decrease of the DeB-values in plastic materials occurs and this is taken into account in Eq. (6-23). References Brandsch J, Mercea P, Piringer 0. 1998: in Risch S (ed). New developments in the chemistry of packaging materials, ACS Symposium Series, Washington. to be published. Cussler E L, 1997: Diffusion. Mass transfer in fluid systems, 2 nd. ed., Cambridge University Press. Cell C B. Graessley W W, Fetters L J, 1997: J. Polymer Science: Part B: Polymer Physics 35 1933. Hildebrand J H. 191.5:J. Am. Chem. SOC.37.970. Hildebrand J H, Prausnitz J M, Scott R L, 1970: Regular and related solutions, van Nostrand Reinhold Company, New York. Kestin J, Knierim K, Mason E A, Najafi B. R o S T. Waldnian M. 1984: J. Phys. Chem. Ref. Data 13 229. Koszinowski J, 1986: J. Applied Polymer Science 31. 1805. Landolt-Bornstein, 1969: Zahlenwerte und Funktionen. 11. Band, 5. Teil. Bandteil a Transportphanomene. Springer-Verlag,Berlin, New York. Reid R C, Prausnitz J M, Poling B E. 1987: The properties of gases and liquids, 4 th ed.. Mc.Graw-Hill Book Company, New York. Tanford C, 1961: Physical chemistry of macromolecules, Wiley. New York.
Reactivity in Molecular Crystals Edited by Yuli Ohashi Copyright @ K d a o r h a Ltd .Tokyo. 1999
7 Transport equations and their solutions Otto Piringer
7.1 The transport equations Interactions between packaging and product are always connected with transport processes occurring within the packaging system. A transport process is understood to be a general movement of mass, energy or other quantity from one location to another. An example of mass transport in packed liquid products is the convection that occurs during the heating or shaking of the package. Macroscopic regions of the liquid move with different speeds relative to one another and cause mixing to occur. With heating, a simultaneous transport of heat takes place along with mass transport. The convection of mass and energy takes place in liquid products during distribution of the packaging from the manufacturer to its final storage destination and during heating and cooling of the package. Mixing by convection in viscous and solid packed products has very little or no practical significance. A special case is the mixing of particulate products by shaking, which gives results similar to convection. The most important transport processes in solid, viscous and liquid filled products during the storage period are diffusion and thermal conductance. Mass transport by diffusion and energy transport by conductance have a common molecular basis. They are both affected by the unordered movement of molecules in the medium in which transport takes place. It is the vibration of atoms and groups of atoms, transmitted to neighboring atoms which is responsible for conductance in solids. Unordered collisions between the mobile molecules of a liquid or gas are also a source of mass transport by diffusion (Chapters 5 and 6). A further example of energy transport through packaging into the filled product is electromagnetic radiation. This radiation in the form of light can start chemical reactions or, in the case of microwaves be transformed into heat and then further distributed through the packaging system by conduction or convection. In addition to mass and energy, other quantities can also experience transfer. Flowing layers with different flow rates in a convection stream can influence one another. The slower flowing layer acts as a brake on the faster layer, while at the same time the faster layer acts to accelerate the slower one. The cause of this behavior is the inner friction of the liquid appearing as a viscosity difference, which is a consequence of the attractive forces between the molecules. Viscosity can be explained as the transport of momentum. The viscosity of different media can be very different and thus plays an important role in transport processes.
184
Piringer
7.1.1 The terminology of flow For the mathematical description and understanding of transport processes, it is advantageous for their descriptions to have several common characteristics, regardless of the nature of the transport quantity, to allow them to be treated in a similar manner. Without knowledge of their fundamental causes at the molecular level, which corresponds to their historical development, transport processes can be described with help from quantities that can be quantitatively measured on a macroscopic level. One such quantity is that of flux. The flux J is understood to be the amount of a quantity transported per unit time through a unit surface area. Flux is a vector for which a direction must be specified in addition to the quantity or contribution J. This is accomplished with the help of the unit vector e giving:
J = Je = Jx
+ J, + Jz = Jxi + J y j + Jzk
(7-1)
J,, J,, J, are the vector components in the x, y and z axis directions of the coordinate system, J,, J,, J, are their contributions and i, j and k are the corresponding unit vectors. Given a mass quantity rn that is transported during time t through an area A, then let J represent the contribution of the mass flux. For energy transport, then J is the contribution of the energy flux with the dimensions J/m2s(where J = Joule). In a very general sense, the flux of a quantity G is proportional at a given location to the gradient of the scalar field produced by the flux, a(x, y, z ) . Mathematically, one obtains the contributions of the three components with the gradient of a, grad a, from the partial derivative of a at the coordinates x, y, z which for the flux G results in:
-b
(& @i
a)
J,(mass,convection)
= p
b)
Jz(momentum in x - direction) = -q
c)
J,(mass,diffusion)
d)
J,(energy,conduction)
J(G)=-bgrada
=
+ “j (b + “k az
(7-2) The location independent proportionality factor is designated b. The minus sign in Eq. (7-2) shows that the flux goes in the direction of decreasing a-values. This means the quantity G “flows” down the gradient. The usefulness of the flow terms as common characteristics for transport processes allows them to illustrate such seemingly diverse processes as convection, momentum transport (viscosity), diffusion and heat conductance. To simplify the written expression, the flux components of the four processes are expressed in Eq. (7-3) in the direction of one axis of the coordinate system whereby, instead of the partial derivative for the function, a variable and useful form of the derivative expression is used:
=
i &x dz
k (7-3)
-D a dx i =
-n dx i
In Eq. (7-3a) p and dxldt are the contributions of the density and the velocity of the liquid in the x-direction. The material specific constants q, D and n are for the viscosity, diffusion and thermal conductivity coefficients. The derivatives in the z and x
Trrirrsport equations and their solutions
185
directions, dv,/dz, dc/dx and dT/dx are for the velocity components (in the x-direction), the concentration and temperature. A comparison of the four equations in Eq. (7-3) shows the similarities between the expressions. With respect to their individual historical development, the four expressions above are quite separate. While the above representation of momentum can be traced back to Newton, the expression for heat conductance was first derived by the mathematician and physicist Joseph Fourier at the beginning of the last century. The physiologist Adolf Fick, who was concerned with measuring the transport of oxygen in blood, recognized the analogy of diffusion to heat conductance and published in 1855 the diffusion equation now known as Fick's first law (Eq. 7-3c). The relationships between the different processes at the molecular level was first recognized by Einstein and other physicists and led to quantitative relationships between material specific constants, in particular between D and q , which are important for calculating their respective contributions (see Chapters 5 and 6).
7.1.2 The differential equations of diffusion During a diffusion process, e.g. the migration of an additive from a plastic into the atmosphere, a change in the concentration of the diffusing substance takes place at every location throughout the plastic. The mass flux caused by diffusion is represented by a vector quantity whereas the concentration c and its derivative of time t is a scalar quantity and is connected by the flux with help of the divergence operator. The following example serves to emphasize this relationship. In a body with any given shape, e.g. a piece of soap, there is an aroma compound which is initially uniformly distributed throughout the entire body. During storage without any packaging a decrease in concentration takes place due to diffusion into the atmosphere particularly in the outer layers of the soap. The resulting scalar concentration field with the levels c1 > c2 > c3 (Fig. 7-1) forms a gradient field that describes the external direction of the aroma compound flux.
Figure 7-1. Diffusion and the divergence operator.
186
Piringer
Figure 7-2. Diffusion through a volume element.
Now consider only a suitably small section of the soap in the form of a cube with side lengths of Ax, Ay, and Az (Fig. 7-2). The aroma compound will diffuse in as well as out of the cube because of its perpendicular side surface areas. Due to the greater decrease in the aroma near the soap’s external surface, the flux out of the side of the cube closer to the surface is greater than the flux into the side of the cube that lies deeper in the soap. The difference between the aroma diffusing in and out will be positive which means one can consider the cube as an aroma source. As a consequence of the flux out of the cube, the concentration in the cube decreases with time. The concentration is also a function of time, c = c(x, y, z, t) and its decrease with time, i.e. the partial derivative -&/at in the cubic volume AV = Ax Ay Az, represents the net flux out of the cube and designated div J the divergence of the flux. Mathematically the divergence is obtained as the sum of the differences between flux components in and out of the cube in the coordinate axis direction with respect to the cube’s volume. Placing the coordinate axis parallel to the corners of the cube as a helpful construction (Fig. 7-2), then one can label the incoming flux component contributions through the side walls Ay Az at the location x with Jx(x) and the outgoing component through the opposite side wall at x + Ax on the x-axis with Jx(x + Ax). When this is done in the same manner for the other components, then one gets:
+
IJZ(Z+AZ)- J ~ ( z )Ax ] Ay Ax Ay Az
(7-4a)
By letting the length of the cube’s sides Ax, Ay and Az become infinitely small, then the differences on the right side of Eq. (7-4a) become the partial derivatives of the flux component contributions at the location P(x, y, z) and one obtains: (7-4b)
Trnrisport equations and their solutions
187
Then the contribution of the diffusion flux in the direction of the three coordinate axis are according to Eqs. (7-2) and (7-3c):
J, = - D &/Ox, J, = - D i)c/dy and J,
=
-
D &/dz
(7-5)
With help from the divergence and gradient, one obtains the same result in the form of the expression: div J = D div grad c
=
(7-6)
The mathematical operator V, called Nabla or del, appearing in Eq. (7-6) has the structure:
When del is applied to concentration c, Vc = grad c, and to the vector of the diffusion flux J = -D grad c, it gives VJ = - div J = D div grad c = DV'c. The application of the del operator twice leads to a scalar, to a vector and once again to a scalar, then i - i = j - j = k - k = 1 and i . j = i - k =j - k = 0 and subsequently:
Eqs. (7-5) and (7-6) are known as Fick's second law for the case where the diffusion has a constant diffusion coefficient. The immediate result of the above discussion is that the diffusion equation can be transformed into the differential equation for heat conduction by substitution of c by T and D by IC. This analogy has the consequence that practically all mathematical solutions of the heat conductance equation are applicable to the diffusion equation. The analogy between diffusion and conductance should be kept in mind in the following discussion although the topic here will be mainly the treatment of the diffusion equation, which represents the most important process of mass transport.
7.1.3 The general transport equations If diffusion and convection currents are similar in magnitude then the total transport is the sum of all the individual contributions. While convection currents caused by mild shaking of low viscosity liquids lead to a much faster mixing than by diffusion processes, the influence of convection decreases with increasing viscosity (e.g. mayonnaise). A decrease in concentration in addition to physical transport effects can also be the consequence of a chemical reaction taking place. The concentration decrease per unit time caused by chemical reaction is defined as the rate of reaction r and is a function of the concentrations present at the reaction site:
The proportionality factor k is the reaction rate constant. The exponent n, usually 1 or 2, specifies the order of the reaction.
188
Piringer
The simultaneous occurrence of reaction and transport processes can be represented by adding the contributions together and, for the total concentration decrease over time at a given point P(x,y,z) in the media considered by the general transport equation one obtains:
II
- _
at total
= div
J (Diffusion)
+ div J (Convection) +
r (reaction)
A typical example of transport and reaction occurring during storage of a package is the spoilage of fat-containing food by oxidation with oxygen transported from the atmosphere through the packaging. Equation (7-10) is a mass balance. At every location a decrease in concentration of substance i takes place by transport and chemical reaction. Thus the total decrease -&/at is equal to the amount of substance leaving the location, which includes the changes due to diffusion and convection plus the loss due to chemical reaction. By this the description of the location where the processes take place is properly described as the source of substance i.
7.2 Solutions of the diffusion equation For interactions between packaging and product the above descriptions of both material transport processes by diffusion and convection as well as the simultaneous chemical reactions come into consideration. The general transport equation (7-10) is the starting point for solutions of all specific cases occurring in practice. Material loss through poorly sealed regions in the package can be considered as convection currents and/or treated as diffusion in the gas phase. A solution of the general equation delivers the concentration contribution at every point in time and at every location throughout the volume considered, thus c = c(x, y, z, t). The general form of the transport equation as a second order partial differential equation has no solution. Analytical solutions are given however for numerous special cases. For solutions involving complicated cases, simplifying approximations are used or numerical solutions are carried out. Since the general equation (7-10) represents a starting point not only for interesting interactions but also for the complete chemical reaction technology, there are numerous solutions described in the literature which can be applied to interaction problems. The usefulness of analogous considerations was already mentioned in the comparison of diffusion and heat conductance. Since Eq. (7-10) is composed of the sum of its members, it is logical to consider next the contribution of each individual component. The fastest step in a group of simultaneous overlapping processes is the most important. If the overall process is the result of a series of processes taking place one after another, for example as a consequence of transport processes through one or more boundary surfaces, then the slowest step of the process determines the rate of the overall process. Mass transport by diffusion is without doubt the most important process throughout the storage of packed products. The discussion of the solution begins then with the diffusion equation Eqs. (7-5) or (7-6). In order to start with the most general case in which the diffusion coefficient D is not constant, one can also write:
Trailsport equations and their solutions
189 (7-11)
While numerical methods come into question for solutions involving variable D, D can be assumed to be constant or practically constant for most cases of practical interest. In addition, simplified solutions for diffusion along the x-axis can be used instead of the general solution, except for some particular cases which will be pointed out later. This greatly simplifies presentation of the problem and the resulting equation for diffusion is:
(7-12)
7.2.1 Steady state The simplest case t o solve is when the concentration stays constant over time in the polymer. If diffusion occurs only along the direction of the x-axis then: (7-13)
D $=O
This particular case exists for example in the diffusion of a substance through a film with thickness d (Fig. 7-3) if the concentrations at the two surfaces C I at x = 0 and c2 at x = d remain constant (stationary case):
0
X
d
Figure 7-3. Diffusion (permeation) through a film at steady state.
A first integration of Eq. (7-13) then gives:
* dx
= constant
(7-14)
A constant concentration gradient exists in the film perpendicular to the film’s surface and consequently there is a constant diffusion flux in the x-axis direction according to Eq. (7-3c) at every location between x = 0 and x = d. Integrating Eq. (7-14) again leads to:
190
Piringer
c-c1 ~2 - ~1
-s
(7-15)
d
and the amount of the flux through the film is:
.D & = D dX
d
(7-16)
7.2.2 Nonsteady state A number of solutions exist by integration of the diffusion equation (7-12) that are dependent on the so-called initial and boundary conditions of special applications. It is not the goal of this section to describe the complete mathematical solution of these applications or to make a list of the most well-known solutions. It is much more useful for the user to gain insight into how the solutions are arrived at, their simplifications and the errors stemming from them. The complicated solutions are usually in the form of infinite series from which only the first or first few members are used. In order to understand the literature on the subject it is necessary to know how the most important solutions are arrived at, so that the different assumptions affecting the derivation of the solutions can be critically evaluated. Most solutions of the diffusion equation (7-12) are taken from analogous solutions of the heat conductance equation that has been known for many years: (7-17) which can be directly applied to diffusion problems. The standard reference work on the mathematics of diffusion is by Crank (1975), from which most of the solutions contained in this chapter have been taken. The solutions themselves have their origins in the older and more comprehensive reference work on heat conductance in solids by Carslaw and Jaeger (1959). The selection of diffusion equation solutions included here are: diffusion from films or sheets (hollow bodies) into liquids and solids as well as diffusion in the reverse direction, diffusion controlled evaporation from a surface, influence of barrier layers and diffusion through laminates, influence of swelling and heterogeneity of packaging materials, coupling of diffusion and chemical reactions in filled products as well as permeation through packaging.
7.2.3 Diffusion in a single phase homogeneous system The diffusion problem is simplest to solve analytically if the diffusing substance is concentrated at the beginning of the process in an infinitely thin sheet (plane) and then diffuses perpendicular to the plane of this sheet into an infinite liquid media found on both sides of the sheet. The flowing away from or diverging from the source is, once more, a graphic example for the expression of the diffusion equation in the form represented in Eq. (7-6): -dc/at = div J. A model corresponding to this situation can be represented by a long cylindrical shape made from a polymeric material, e.g. polyethylene, with a cross section of 1 cm2. In the middle of the material there is a very thin layer of material colored with a pigment which acts as a diffusion source (Fig. 7-4a). The color molecules then diffuse outwards towards both ends of the bar
191
Transport equations and their solutions a
6.
1
I o,8i "'€1 A 1
0
- X t -
Ib
0.6
-+X
0.4
i,
Dt=0.3
0.2
0
--
__.I
-3
-1
-2 -x
0
-._ 2
1
3
x
Figure 7-4: a ) Two sided diffusion from an infinitely thin layer (source). b) Distribution of concentrations for different values of the product Dt.
along the x-axis of the coordinate system without reaching the ends of the bar during the time interval considered. At t h e beginning of diffusion, time t = 0 and the total amount of color having mass m is located at position x = 0. Because of the theoretically infinitely thin layer 6x of the color source, the initial concentration there is infinite and the concentrations at all other positions of the bar are zero. The solution of the diffusion equation (7-12) is immediately given as: c=
A
exp
(-a&)
(7-18)
1 1 -
where A is the integration constant whose formation can be easily checked from the partial derivatives ocli3 and i)2cldx2 from Eq. (7-12). The expression in Eq. (7-18) is symmetric with respect to x = 0 because of x2 and goes to zero if x becomes positively or negatively infinite and t > 0. With help from the substitution:
_ _ = q2;
dx
=
2 (D t)ll2 dq
(7-19)
and because the total amount m is obtained, which means: +x
m = ,[ c dx
(7-20)
--x
one can write: +x
m = 2 A D1/2
exp (- q2) dq = 2 A (n D)'/'
(7-21)
--x
The values for A resulting from Eq. (7-21) are used in Eq. (7-18) and then one obtains the solution: (7-22) for the spreading of the color by diffusion. The increased spreading with time can be seen in Fig. 7-4b.
192
Piringer
In the above case, half of the substance diffuses in the positive direction and the other half in the negative direction of the x-axis. If an absolute barrier is now assumed to exist at position x = 0 so that diffusion can occur only in the direction x > 0 then the half of m diffusing in the x < 0 is reflected by the barrier and overlaps the other half diffusing in the x > 0 direction (Fig. 7-5a). Because the symmetry of the curve (7-22) with respect to the source at the position x = 0, one obtains a solution for diffusion in a half open media that is double the value of Eq. (7-22): c=-
(7-23)
The requirement of a barrier layer at x = 0 is expressed mathematically by the boundary condition of 8c/& = 0 at x = 0. The first complication for the application of the diffusion equation Eq. (7-12) comes when the complete left half of the plastic bar, x < 0, is uniformly and completely colored with coloring agent which can diffuse in the direction of x > 0 (Fig. 7-5b). The concentration of the color is expressed by the finite concentration of co. In order to find a solution to the problem the colored region x < 0 is thought of as being divided into an infinite number of layers perpendicular to the x-axis. In doing this, the problem can be related to an infinite number of diffusion sources and the mathematical solution can be arrived at by overlapping many solutions of the form of Eq. (7-18). Considering the thickness 6s of such a source (Fig. 7-5b), then one gets the amount of substance contained in the cross section of the bar, co 6s, because it has the unit surface area. One obtains the expression for the concentration c, of the color originating from this source at a distance s at time t according to Eq. (7-22): 2
(K
(7-25)
D t)‘
The integration of c, over all layers 6s gives with Eq. (7-25) the concentration c(x, t) at any position x > 0 at time t:
(7-26)
b
a
il 0
-X-
+X
-X-
s
O
-+x
Figure 7-5: a) Single layer diffusion from a source with a bamer on one side. b) Diffusion from an infinite thick layer represented as coming from infinitely many sources.
Trmsport equations and their solutions
193
With c,(x, t), the concentration coming from the source is designated for position x at time t at a distance s from the initial point. In order to make the right side of Eq. (7-26) easier to use, the following relationship can be considered:
1 - erf(z) = erfc
=
(7-28)
(2)
where the error function erf (z) is given by: erf(z) = $Texp(-q2)
dq,erf(-z)
=
-erf(z);erf(O) = O;erf(m) = 1
(7-29)
0
for which complete tables are available (Table 7-1). The complement of erf (z) is designated erfc (z) and is also given in Table 7-1. The solution Eq.(7-26) can now be expressed in a convenient and easily useable form: c (x, t)
= 2:1 c0
erfc
(7-30)
Table 7-1: Table of different error function forms. z
erf z
erfc z
F(Z)
0.00
0.000000
1.000000
0.00000
1.10
0.880205
0.119795
0.59827
0.05
0.056372
0.943628
0.05401
1.20
0.910314
0.089686
0.62146
0.10
0.1 12463
0.887537
0.10354
1.30
0.934008
0.065992
0.64236
0.15
0.167996
0.832004
0.14908
1.40
0.952285
0.047715
0.661 26
0.20
0.222703
0.777297
0.19098
I .so
0.Y66105
0.033895
0.67841
0.25
0.276326
0.723674
0.22965
1.60
0.976348
0.023652
0.69405
0.30
0.328627
0.671373
0.26540
1.70
0.983790
0.016210
0.70834
0.35
0.379382
0.620618
0.29850
1.80
0.989091
0.010909
0.72144
0.40
0.428392
0.571608
0.32921
1.90
0.992790
0.007210
0.73349
0.45
0.475482
0.524518
0.35775
2.00
0.995322
0.004678
0.74460
0.50
0.520500
0.479500
0.3843 I
2.10
0.997021
0.002979
0.75488
0.55
0.563323
0.436677
0.40907
2.20
0.998137
0.001865
0.76441
0.60
0.603856
0.3961 44
0.43220
2.30
0.998857
0.001 143
0.77326
0.65
0.642029
0.357971
0.45382
2.40
0.999311
0.000689
0.78150
0.70
0.677801
0.3221 99
0.47407
2.50
0.999593
0.000407
0.78919
0.75
0.71 1156
0.288844
0.49306
2.60
0.999764
0.000236
0.79640
0.80
0.742101
0.257899
0.51090
2.70
0.999866
0.000134
0.80310
0.85
0.770668
0.229332
0.52767
2.80
0.999925
0.000075
0.80950
0.90
0.796908
0.203092
0.54347
2.90
0.999941
0.000041
0.81540
0.95
0.820891
0.179109
0.55836
3.00
0.999978
0.000022
0.81540
1.00
0.842701
0.157299
0.57242
194
0 1
Piringer
0” 0.5
Figure 7-6: Concentration distribution curve for diffusion from an infinitely thick initial layer.
X __ 2 m
The shape of the concentration curve is shown in Fig. 7-6. At position x = 0, c = 0.5 cg for all values o f t > 0. The amount of substance diffused into the uncolored portion of the bar up to time t (shaded region after x > 0) is equal to the amount of substance diffusing out of the colored portion (shaded region x < 0). Example 7-1. A 10 cm high cylindrical shaped wheel of cheese contains a homogeneously dispersed ingredient with a concentration c,, = 100 mg/kg. A second similar wheel of the same type of cheese without this ingredient is laid on top of the first wheel. Assuming there is intimate contact between the two wheels o f checsc. what is the concentration of this ingredient in the second block of cheese at a depth of 1 mm after 25 hours of contact? D = 3E-7 cm2/s. This problem corresponds to the example in Figure 7-Sb. A 10 cm thick wheel of cheese can be considered to be infinitely thick with respect to the diffusion coefficient provided the contact time is not too long. Eq. (7-30) can be used to solve the problem. For x = 0.1 cm, t = 2Sh 3600s/h = 90000s and D = 3E-7 cm’h on calculates:
Looking up the value for erfc z in Table 7-1. erfc(0.3) = 0.671373, and using this value in Eq. (7-30) the concentration of the ingredient at this time and distance can be calculated to be: c(x, t) = . c0 erfc(z) = 0.5 . 100 0.671373 = 34 mg/kg
f
Example 7-2. What would the distance from the surface of the second wheel for the 34 mg/kg concentration from Example 1 be after a) three months? b) after one year? Assume that the storage conditions remain constant and the properties of the cheese wheels also remain constant during these times. Because the z values from Eqn. (7-30) will always lead to the same concentration (i.e. 34 mg/ kg), one can simply solve z for the distance: After 3 months: (3mo .30d/mo .24h/d 3600s/h = 7776000 s: X X z =- 0.3 x = 0.93 cm 2 ( D ti”’
= 2 (3 09E-7 7776(XXh)’” -
After 1 year: z =
X
2 [D.l)’/’
~
~
-0.3
2 - ( 3 096-7.31 IllJO~Xls)”2 -
x = 1.9 cm
Trrrrisport equations and their solutions
195
Dimensionless parameters and the proportionulity of mass transfer to the square root of time
In order to compare results of studies that are expressed in different quantities, dimensionless representations are always preferred. Examples of dimensionless quantities are the relative concentration c/cOalready mentioned above and the parameter appearing in the error function z = x / 2 (D t)1’2 in Fig. 7-6. Systems described with help from the same model but differing from one another with respect to material constants, e.g. D values, can have the same z and c/co values at different times. As a result, whole series of curves can be represented by a single, easy to read curve. Since the same z values always lead to the same c/co values, the distance xc which is the distance the diffusion front having concentration c has traveled from the surface with a constant initial concentration cg to time t, the definition of z is given as: 2 (D t)lI2 z xc :
(7-31)
Like in the solution given for the diffusion out of a bar colored on one side bar in Eq. (5-30),it can be seen that the same c/co values always result for the same z values. This means that the diffusion front of a given concentration c is proportional to the square root of Dt. The error function used in solving the above diffusion problem occurs as a consequence of the summation of an infinite number of infinitely thin colored layers, which themselves bring about an exponential distribution of the concentration. Because of the error function’s significance for numerous practical cases, this solution will be treated in somewhat more detail. In the same manner, one obtains a solution to the diffusion equation starting with a colored layer having a finite thickness 2d and an initial concentration cg in both directions of the unbounded x-axis (Fig. 7-7): (7-32)
In the next example a short section of length 1 is cut from the plastic bar (Fig. 7-8). The bar is uniformly colored from one end up to a layer thickness of d with a pigment having concentration co. The zero position of the x-axis is assigned to the colored end of the bar. With the mathematical boundary conditions x = 1, ac/ax = 0, one finds that the diffusion of a color molecule in the uncolored section cannot go further than the theoretical barrier existing at x = 1 and is reflected back. For illustration purposes the representation of the concentration profiles of this process are shown by straight lines with different slopes in Fig. 7-8. The reflected path of the curve from a source 6, now overlaps the original curve and the concentration at a given location x of the bar is the
-X
-
0 -+x
Figure7-7: Two sided diffusion from a finitely thick layer.
196
Piringer
Figure 7-8: Single sided diffusion from a finite thick layer into a finite layer of the same material.
sum of the two contributions. A further reflection takes place at the other end of the bar at x = 0 and then again at x = 1 and so forth, whereby every reflected curve section overlaps the previous section. Because the original curve is already represented as the sum of two error functions, the complete system is represented by a series of error functions:
’
i co n = O [erf (d 2+ (D2 n l - x t)l/*
)
+
erf
(
d-2nl+x 2 (D t)’/*
)]
(7-33)
Even though the above method of solution of the diffusion equation (Eq. 7-12) becomes impractical for complicated cases, it illustrates the appearance of the error function in problems where diffusion from an infinite number of sources occurs and the solution is obtained in the form of an infinite series as a result of the overlapping of diffusion streams. The overlapping diffusion streams are due to an infinite number of repeated reflections at the ends of the diffusion path which are spaced finite distances apart. As seen in Fig. 7-8 the decrease in concentration is shown by sloping lines so that after each reflection the corresponding amount relative to the total concentration c becomes smaller. Due to the exponential character of the solution, the decrease is much more rapid than in the simplified representation shown in the figure and the series converge very rapidly, so that after a few terms the total concentration at a given location and time stays practically constant. There are other different methods for solving the diffusion equation in Eq. (7-12) which are described in mathematics books. Older methods, in particular separation of variables x and t are worth mentioning. They also produce infinite series in their solutions in the form of the Fourier trigonometric series. A further, very elegant analytical method uses the Laplace transforms (Kreyszig 1993). In addition to analytical solutions the possibility exists to obtain numerous exact solutions using numerical methods with help from computers. The advantage of numerical methods lies primarily with their application for complicated cases, e.g. for non-constant diffusion coefficients, for which there are no analytical solutions.
Transport equations und their solutions
197
Example 7-3. A 100 pm thick plastic film contains an initial concentration of 100 mg/kg of some additive. This film is brought in direct contact with another 100 pm thick plastic film of the same material initially containing no additive. Assuming ideal contact between the two films (i.e. no boundary conditions exist to hinder the transfer across the interface). The exterior sides of the f i l m are no1 permeable (they are in contact with a glass or metal surface). The diffusion coefficient of the additive is 3E-7 cm2/s for both films. What is the concentration on the outside of the second film after one minute contact time? This example corresponds to Fig. 7-8 in the text. The solution can be obtained using Eqn. (7-33). Putting d = 0.01 cm, 1 = 0.02 cm and x = 0.02 cm one gets a constant sum of c = 14.8 mg/kg after two steps n = 0 and n = 1: c =1 ' C() ' 2
5{
erf(ci
n=O
;, { (" erf
cg
n=O
forn=O: forn=O: forn=1: forn=1: forn=-1: forn=-l: c=
1 '
(+ ( ( ( (+ (
f 2 . n . I - x) 2 . (D . t)'/*
2 . (D . t)'I2
d -2.n . I
+
+
(" ("
erf
erf
)=( + )=( + )=( )=( ) =( + )=( +
2.n ' 1 -x
d
+
- 2 . n .I x) 2 . (D . t)'/'
- 2 , n . 1 +x) 2 . (D . t)'/'
}+ }
0.01 f 2 ' 0 0.02 - 0.02 2 (3E - 7 . 60)1'2
x
2 . (D . t)1/2
0.01 f2 . O -0.02 + 0.02 2 (3E - 7 . 60)'12
d+2 .n . I -x
0.01
2 (D . t)'/' d-2.n.l-t~
2 . (3E - 7 . 60)'12 0.01 2 ' 1 0.02 + 0.02
2 . (D . t)'/'
2 . 1 .0.02 - 0.02
-
= -1.1785
= 3.5355
= 3.5355
'
2 . (3E - 7 . 60)'12
2.n 1-x
0.01 - 2 1 .0.02 - 0.02
2 . (D . t)"2 d - 2 . n .1 x 2 . (D . t)'/'
2 . (3E - 7 .60)'/' 0.01 2 . 1 '0.02 + 0.02 2 . (3E - 7.60)'/'
d
=
-1.1785 =
-5.8926
= 8.2496
+ erf(3.5355) + erf(3.5355) + erf(-1.1785)}+ {erf(-1.1785) + erf(3.5355) + erf(-5.8926) + erf(8.2496)) =
100' {erf(-1.1785)
1 100 2 = 50{-0,9012 -.
+
2 . n , 1 - x) 2 . (D . t)1/2
+ 1 + 1 + -0,9012) + 50{ -0.Y012 + 1 - 1 + l } = 9.88 + 4.94 = 14.8 mg/kg
After terms higher than n = 1 the error function terms start canceling themselves out.
Comparison of different solutions for the same special cases
Various methods can give different expressions for the solution of the same application. Even though these lead to the same result, the solutions of problems in the form of infinite series can converge at varying rates. Consequently some solutions are favored over others, depending on the parameters under consideration. Finally, the considerations of the homogenous plastic bar model will be used as an example to show the differences between different solutions.
198
Piringer
-I
0
+I
-+x
-X
Figure 7-9: Two-sided diffusion into a finitely thick layer.
A plastic bar of “infinite” length (e.g. 1 m or longer) is uniformly colored with an initial color concentration of co (Fig. 7-9) except for a thin layer in the middle with thickness d = 2 1 (approximately 1 cm). As a simplified approximation it is assumed that the concentration of the color at the location x = f 1 remains constant at co. The boundary conditions are expressed mathematically as: c=co,
x=fl,
g=0,
x=0,
t
> o (7.34)
t > 0
The condition of &/ax = 0 at the location x = 0 expresses the requirement that no diffusion can take place through the axis of symmetry at x = 0. This leads to the same result as single sided diffusion in a layer having half the thickness. For the solution of the diffusion equation, Eq. (7-12), two different series expressions can be obtained:
The first series converges very rapidly for not too large values of D t / 12, in other words for relatively short diffusion times. For D t / l2 = 1 the concentration ratio c/co at location x = 0: c/co = 0.9590 - 0.0678 + 0.0008 = 0.8920 and for D t / l2 = 0.25: c/co = 0.3146 - 0.0001 = 0.3145. The trigonometric series in Eq. (7-35) converges rapidly for large t values. For D t / l2 = 1 it is: c/co = 1 - 0.01080 = 0.8920 and for D t / I* = 0.25: c/co = 1 - 0.6872 + 0.0017 = 0.3145.
7.2.4 Diffusion in multi-phase systems In this section the important cases for food packaging are treated. These cases differ from the previous examples in that mass transfer takes place across an interface between two different media with different characteristics, e.g. with different diffusion coefficients. If the value of a quantity is desired, for example the concentration of the substance transported across the interface in one of the two media, then a mass balance must be considered that takes into account the ratio of the contact surface area and the volume of the corresponding medium.
Trnrisport equations and their soiuiions
199
Diffusion in polymer / liquid systems For the sake of conformity, in the following every quantity related to the packaging is designated with the index P; and the quantities related to the food are labeled with the index L. Fig. 7-10a shows a model that describes the mass transfer of a component dissolved in the filled product L, e.g. an aroma compound, into the packaging material P. The model is based on the following assumptions: 1. A component i in the liquid phase with an initial concentration C L . ~is sorbed onto the contact surface area A between the liquid and packaging and subsequently diffuses into the matrix of the packaging. In so doing there is a decrease in concentration in the region of the contact surface which leads to further transport of i from the matrix of the liquid to the contact surface. 2. The mass transfer, controlled mainly by diffusion taking place in the packaging during storage, is several orders of magnitude lower than diffusion in the liquid phase. The difference is even greater when mixing (convection) occurs by shaking, e.g. during transport. It can be assumed that the concentration of component i in L, CL,~, is dependent on time t but not on the distance x from the contact surface. 3. A constant distribution of i between L and P takes place that is independent of concentration of i and time. For relatively small concentrations of i (< 1 YO) this approximate assumption is fulfilled and one defines the partition coefficient K as a constant ratio of the concentration i in the packaging material at time t on the contact surface cp., (dp) to the concentration of i in the liquid independent of location at the same time, c ~ , ~ :
(7-36) Where K is the ratio at t = o(j of the equilibrium concentrations of i in P, cp,, to that in L, this concentration ratio is also sometimes referred to as the relative solubility constant, S,, of i in P (relative to cL.,). 4. The second important quantity influencing the mass transport is the diffusion coefficient DP of i in P. For relatively low concentration ranges assumed for i in L, Dp is assumed to be constant. The diffusion controlled mass transport rate of i in P leads to a decrease in concentration of i with increasing distance from the contact surface (Fig. 7-10a). Particularly in the initial stages of diffusion, the total amount of substance i transferred into the package can be concentrated in a region near to the contact surface next to L while the location dependent concentration of i in P in the matrix of the packaging is equal to zero. 5. The mass transport is assumed to occur in the x direction perpendicular to the contact surface. Even though the geometry of the packaging/product system influences the amount of mass transport occurring, it is of minor significance for most practical cases. 6. All above assumptions are valid for mass transfer in the reverse direction as well. This means the migration of component i from the package into the product is also described (Fig. 7-lob). By considering the corresponding initial conditions the mathematical solution of the problem results in the same form. 7. The contact between packaging and product shown in Fig. 7-10a and b is singlesided. This means the external surface of the packaging at location x = 0 is assumed to
200
Piringer
a
L
P
I
I
C
d
I
x =d,
X=O
P
L
L
L
x =dp+dL
c
d,-
P
L
Figure 7-10. Mass transfer between a packaging material and a liquid product; a) diffusion out of the liquid into the package, b) diffusion out of the package into the liquid, c) cross section of a representative container, d) two-sided contact of a package material with a liquid.
Trmsport equutions and their solutions
201
be impermeable to i. The model also establishes an absolute barrier layer at the location x = dp + dL which simplifies the representation of the problem. A representation closer to conditions in practice is shown in Fig. 7-1Oc for a plastic container with a wall thickness of dp. The single difference to Fig. 7-10a is that the sum of the two contact surfaces A‘ in Fig. 7-1Oc is replaced by A = 2 A’ in Fig. 7-10a and b. In the literature one frequently finds a two sided contact with the packaging using the same model shown by the representation in Fig. 7-10d. Because the axis of symmetry at x = 0 serves as a barrier layer in the mathematical boundary conditions, the expression for the solution is not changed when instead of the half layer thickness dJ2 = 1 for two sided-contact of P, the actual layer thickness dp with single-sided contact is used. This is because in the symmetrical model in Fig. 7-10d the total layer thickness of the liquid dL is taken into consideration. The symmetrical model in Fig. 7-10d also illustrates the common two-sided contact migration measurement practice in which a film or sheet is immersed in a liquid. One obtains the corresponding volumes of the packaging, Vp = dp A, and liquid, VL = dL A, using the layer thicknesses dR dL and the contact surface area A. With the corresponding densities of the liquid, pL, and packaging, pp, the mass of liquid, mL = pLVLand mass of packaging, mp = pp Vp can be calculated. In many practical cases the assumption pL = pp E 1 can be made for simplification without significant error. With dimensionless quantities a and T (7-37) one obtains for the mass transfer by diffusion of i from a well mixed liquid (assumption 2) into a package or the migration in the opposite direction the general expression from Crank:
(7-38) Eq. (7-38) is a solution of the diffusion equation (7-12) for the models shown in Fig. 7-10. Where m, is the mass of i diffusing up to time t from L through the boundary surface A into the package or opposite direction and m, is the amount which has migrated at equilibrium. The parameters qn in the series are the positive roots of the trigonometric identity tan q,, = - a 4., Several values of this parameter for various a and n are given in Table 7-2. The values of q, lie between n n ( for a = 0) and (n - 1/2) n (for a = m). For a << 1 then qn 2 n n/(1 + a ) , and for the remaining a values q, z [n - a/2(1+ a)]n. The solutions of Eq. (7-38) converge rapidly for long diffusion times, while for short times, e.g. at the beginning of diffusion (T z 0.001), approximately 50 terms are needed. Even though this equation is no obstacle for today’s PCs, it is more convenient for short times to use the form of the solution based on the error function: (7-39) with: (7-40)
202
Piringer
Table 7-2: Roots of tan qn = -aq, ~~
a
41
q2
q3
q4
1.5708
4.7124
7.8540
10.9956
4s 14.1372
qh
02
9.0000
1.6385
4.7359
7.8681
11.0057
14.1451
17.2852
4.0000
1.7155
4.7648
7.8857
11.0183
14.1549
17.2933
17.2788
2.3333
1.8040
4.8014
7.9081
11.0344
14.1674
17.3036
1.5000
1.9071
4.8490
7.9378
11.0558
14.1841
17.3173
1.mo
2.0288
4.9132
7.9787
11.0856
14.2075
17.3364
0.6667
2.1746
5.0037
8.0385
11.1296
14.2421
17.3649
0.4286
2.3521
5.1386
8.1334
11.2010
14.2990
17.4119
0.2500
2.5704
5.3540
8.3029
11.3349
14.4080
17.5034
0.1111
2.8363
5.7172
8.6587
11.6532
14.6870
17.7481
0.000
3.1416
6.2832
9.4248
12.5664
15.7080
18.8496
In Table 7-1 the values for the function contained in brackets in Eq. (7-39) are given as: F(z)
=
1
-
exp (z2) erfc (z)
(7-41)
Equation (7-39) is particularly suitable for T < 1 and a < 100. A convenient rational approximation of the error function formula in Eq. (7-39) is: 5
x = ( I +a) 1 m ,
-
C n = l
anr”
I
(7-42)
with r = 1/(1 + 0.3275911 T1’2/a); a l = 0.25482592; a2 = -0.28449636; a3 = 1.42141371; a4 = -1.45315207; a5 = 1.061405429. For T > 1 or a > 100 this approximation must not be used (Chang, 1988). The solutions in Eqs. (7-38), (7-39) and (7-42) are valid for material transfer of a component i from food into the package (Fig. 7-10a) as well as for the migration from packaging into the food (Fig. 7-lob) under the assumptions of the described model. However, because at the beginning of diffusion in the first case the total amount mo of i is in L and in the second case it is in P, the values of m, and mOcrelative to mo must be different for the two cases.
1. Mass transfer from L into R The mass balance for i is given as: VL
CL,m
+
VP
CP>,
= VL CL,0 = mL.0
(7-43)
where cL.0 is the initial concentration of i in L. For the amount m, = mp,nc,the amount of substance i in P after reaching equilibrium is obtained from Eq. (7-43) with the L , ~ Eq. (7-36) when Eq. (7-37) is taken into consideration: definition K = C ~ , ~ / C from (7-44)
Trctnsport equations and their solutions
203
The ratio of mP,= and mL,o labeled Up,, shows the fraction of the total amount of i in the package at equilibrium: (7-45) For a = 1then up t o half of i would diffuse into the package at equilibrium. 2. Migration from P into L.
The total amount mp,o of i is contained in P at time t = 0 and the mass balance is expressed as: VL
CL.X
+
VP CP,,
= VP CP,0 = mp.0
(7-46)
The amount of substance transferred into the food at equilibrium m, = mL,m= V L . C ~ ,is obtained by combining Eqs. (7-36), and (7-37): (7-47) and related to mp.o the fraction of the total amount is given by:
The fraction of i diffused from L into P up to time t, from mL.(] = VL cL.0 and the fraction migrated from P into L up to time t, from mCo= Vp cP,()are: (7-49)
(7-50)
Example 7-4. Ten 4 cm diameter circular 200 pm thick plastic film pieces are mounted on a stainless steel wire and placed in a glass vial containing 100 ml solvent. What percentage of the additives initially contained in the plastic migrate into the liquid over the 24 hour period ( D p = 2.1OE-10 cm2/s)? Note that the plastic additives are readily soluble in the solvent, the solvent has low viscosity and the solvent does not swell the plastic. This case corresponds to Fig. 7-10b with variation 7-10d. Because the additives are readily soluble in the solvent K z 1 can be assumed in Eq. (7-36). The volume of the plastic is: Vp = 10. n:. r2 . h = 10 K 2 cm2 0.02 cm = 2.51 cm3 llsing Eq. (7-37) one gets:
Given the two sided contact of the liquid with the plastic 0.5 d p = 0.5.0.02 cm = 0.01 cm and thus with Eq. (7-37) one gets for T: Dp.1
2 IE-lOcmZ/s (2460.60 s)
(0.01 cm)*
= 0.181
204
Piringer
With a = 39.8 one uses the values for a equal to infinity (00) in Table 7-2 for the roots of tan qn = -CI. q,?.Carrying out calculations with Eq. (7-38) for the fraction of additive migrating at time f to what would migrate at f = co:
1 -
2.3Y.X(l+39.8) I +39.8+3Y.X2I 570S2 exp(-1.570S2
2-39.8(1+39.X)
.0.181) - 1+.3Y.X+39,824,7,242exp(-4.71242 .0.181) =
1 - 0.65544 - 0.001657 = 0.473 Note that for the summation the second term is quite small. Because the mass balance for migration out of plastic into a liquid (Eq. 7-47) shows mL.x, = mp.0: a
mL.r = mp.0,
39.8
= mp.O1+39,
I
..
2 mP.0
Therefore, the percentage of additive that has migrated from the polymer in 24 hours is according to Eq. (7-50) is 46.1 YO:
Example 7-5. What percentage of the additives migrate out of the plastic into the liquid in Example 4 when the partition coefficient K = 133? Starting with Eq. (7-38) one first calculates mt/m,: a = -1 .vL = -1. _100 = 0.300 K
133 2.51
Vp
1 - 0.13368 - 0.00128 = 0.865 Note that the values for q,, are estimated by linear interpolation of Table 7-2 values. Now calculating the fraction migrated from the polymer into the liquid: mL1 a 03 U L ,= ~ 2 - = 0.865 . __ = 0.20 mL.x
]+a
1+03
The percentage remaining in the polymer is 20 YO.Compared with Example 4, this result illustrates the effect of the larger partition coefficient where the migrant is more favorably retained in the polymer as opposed to the liquid. Example 7-6. Solve Example 4 using Eq. (7-39) and compare the two results. Starting with a = 39.8 and T = 0.181 from Example 4 calculate the value for z: T'12
z = - =a
0.181'/z
~- - 0.01069 39.8
Entering this value for z in Eq. (7-39) one can solve for m,/m,: ml -=
my
(1 + a )[l - exp(z2)erfc(z)]= (1 + 39.8) [l - exp(0.010692)erfc(0.01069)]=
(1+ 39.8) [l - e~p(0.01069~) . (0.98795)] = 0.487 Then calculating the fraction migrated using the mass balance equation: mLl a 3Y x U L ,= ~ _ _ . - = 0.487 . __ = 0.475 mLx
l+a
1+3Y.X
Transport equations and their solutions
205
rhus 47.5 % of the additive in the polymer migrates in 24 hours which is very close and within :xperimental error to the result in Example 4 of 46.1 %. Vote the values of erfc(0.01069) are estimated from the Table 7-1 values by linear interpolation.
Example 7-7. Edible oil is stored in a plastic bottle with an external diameter of 10 cm and with a wall thickness of 2 mm. What percent of the antioxidant contained in the plastic bottle nigrates after a) 100 days and b) after 2 years into the oil when the antioxidant has a diffusion :oefficient of D p = 1E-11 cm2/s? I ) This example corresponds to the case shown in Fig. 7-1Oc. Calculating a, Tand z:
, = - I. LV= - AI -d - 1 4 . 8 - 24 K
K dp
Vp
r = -d=i c=-=
1 0.2
IE-llcm2/s (100.24-6l)bOs)
Dp t
= 0.00216
(0.2 cm)2 0.00216'~'
TI/?
~
24
= 0.00194
For small times one can use Eq. (7-39) and performing linear interpolation on the z values between 1 and 0.05 in Table 7-1: mt -=
n,
(1 + a)[l- exp(z2)erfc(z)]= ( I
+ 24)[1 - exp(0.001942)erfc(0.00194)]=
( 1 + 24) [l - e ~ p (0 . 0 0 1 9 4 .~(0.997813)] ) = 0.0546 m~~
UL I = ~.
mLx
a
-=
I+a
24
0.0546 . = 0.0524 1124
Thus 100' mL/mx= 5.24 YO migrates b) Using Eq. (7-39): = Dp' = IE~11cm2/s-(2.3h5.24h0.60s) d; TI,'*
z = - = a-
= 0.01577
(0.2 cm)2
0.01.5771/2
24
= 0.005232
Using the same Eq. (7-39) and performing a linear interpolation on the erfc values for z between 0.05 and 1.0 in Table 7-1: mt
-= n1
(1
( 1 + a ) [l - exp(z2)erfc(z)]= (1 + 24) [ I
-
e~p(0.00523~)erfc(O.00523)] =
+ 24) [l - e ~ p( 0 . 0 0 5 2 3 ~(0.994104)] ) = 0.1467
UL.t
mLI
a
= -..-= Ita niL
24
0.1467. -= 0.141 1+24
Thus 100. mt/m,= 14.1 %
Example 7-8. Plastic film 100 pm thick are placed between 3 mm thick slices of cheese. How many mg of plastic additive are found per kg cheese after being in contact for one day given the initial concentration of additive is cRo = I g/kg and the diffusion coefficient in the plastic is D p = 2E-10 cm2/s? The diffusion coefficient in the cheese is D L= 1E-7 cm2/s and the partition coefficient between the plastic and cheese is K = 1. The densities are pL = pp = lgkm'. This problem corresponds to the example shown in Fig. 7-1Oc. First it is necessary to calculate (Y and 7?
206
Piringer 2E-IOcm2/s.(24.60.60 s)
Dp.t
T = - d;-
(0.01
-
= 0.1728
Using Eq. (7-38) one calculates m,/m,:
1 - 0.53931 - 0.0020026 Given that: K = l = S
CL.r
’ ; , c L.m
0.45869
= CP.,
One can use the mass balance Eq. (7-46) to calculate C L . ~ . : Using the mass balance Eq. (7-46) to calculate the concentration of additive in the cheese: VL . C L . + ~ VP . CP., = VP . cp.n = mP.0 0.3 cm3 . C L +~ 0.02 cm3 C L , ~ = , 0.02 cm3 . lmg/cm3 cL.%= 0.0625 mg/cm3 = 62.5mg/kg.
By definition: CL.1 mL.1 _ =__
mL.r
CL.%
Then solve for CL.~: CL.1
-=
62.5
0.45869, :. c ~=.28.7 ~ mg/kg
In order to take into account the influence of the rate of diffusion in the cheese, Eq.(7-56) is used to calculate p: D p = -I . ( L)= -1 .
K
1
DP
The effect of smaller.
(-)1E-7 2E-10
‘1’
= 22.4
p on Eq. (7-57) versus Eq. (7-54) without p is about ( p / c I + p )
=
0.957 (4.3 %)
With equations (7-38) and (7-50), taking the mass balance into account, the migrated amount mL.,through the contact surface A during time t can be calculated as follows [if the dimension of cp,gis w/w (mg/g), then cp.0 . pp means w/v (mg/cm3)]: (7-51) The following equation (7-52) represents the simplified form of Eq. (7-51) for a >> 1:
-
(7-52)
qn = (2n-l)n/2.
Equation (7-53) is an alternative migration equation for small t-values using the error function:
Trcmsport equations and [heir sollitions
207 (7-53)
mL.tlmL..x. L 0.5
The following equation (7-54) is a simplified migration equation for K 5 1 and relatively small t-values, for which an infinite thickness of P is assumed: = 2 ~ ~ , ~Dpt)1/2= p p ( 1.128cp7opp(Dpt)'/*rcp30pp(Dpt)' I 2
J=
(7-54)
The maximum amount of migration derived from the mass balance is:
(7-55) Two typical examples of food packages with the corresponding values of the needed parameters are shown below, together with the results obtained with Eqs. (7-51) to (7-54): A = 600 cm2, d p = 0.02 em, pp = 1 g/cm', t = 864000 s (10 d), cp,o= 1000 mg/kg, DP = 1.OE-10 cm%, K = 1.
vL= 1000 cm'.
a = 83 mL.,/A (mg/dmz)
VL= 300 cm3, a = 25
(7-51)
1.042
1.030
(7-52)
1.047
1.047
(7-53)
1.049
1.049
(7-54)
1.049
1.049
Calculated with equation
The maximum amounts mL,,/A 1.92 mg/dm2, respectively.
m~.t/A (mddm')
calculated with equation (7-55) are 1.98 and
Example 7-9. Solve example 8 using the approximation equation solution in Eq. (7-54) and compare the two results. Given that: VL= AdL-= 2 cm2 0.3 cm = 0.6 cm' one can then calculate cL., using Eq. (7-54):
-
C L t =--m L ' "L PL
A cp,oK(Dpt)i'2= 1000-2 ( 2 . lo-'()' 2 4 60.60) 112-- 13.9 mg/kg.
06
This is a difference of 6.4 % between the two results which is well within most experimental migration measurement errors.
In order to use the migration equations, especially the generally accepted equation (7-51), values for the partition coefficient K of the migrant between P and L and the diffusion coefficient D P of the migrant in P are needed. For migrants with a high solubility in the foodstuff or simulant, the value K = 1 can be used and a worst case estimation is obtained in this way. For migrants with a low solubility in the foodstuff or simulant water K = 1000 can be used to obtain a worst case estimation (see also Chapters 4 , 9 and 15).
208
Piringer 1 --
I
Figure 7-11: The behavior of mass transfer from a packaging material into food for different a values.
Currently, there exists only a limited number of reliable diffusion coefficients, due to the enormous requirements needed for the experimental determination. However, even for diffusion coefficients useful estimation procedures exist (see Chapters 6 and 15). The diffusion coefficient at a given temperature T depends on the nature of the polymer, the mass and structure of the solute and on the activation energy E, in the diffusion process. The material transport from a liquid assumed to be well mixed, into packaging and the migration from packaging into a liquid both vary proportionally to the square root of time and the square root of the diffusion coefficient. While in the beginning phase (approximation equation is only valid for small z values, meaning short times) the mass transfer of i into the package is proportional to K, the migration of i from the package is independent of K. The partition coefficient plays a deciding role in the sorption (solution) of i in the packaging layer in contact with the liquid. This leads to the total amount of sorbed material being concentrated in a thin layer of packaging material in contact with the liquid and the transport process in the initial stage is independent of the material thickness. In contrast the migration process into the liquid takes place independent of K. Due to good mixing in the initial stages of migration, the total amount of material i is transported away from the contact layer of liquid into the volume of the liquid, so that the concentration in the liquid contact layer goes to zero. The rate of diffusion of i out of the package is the rate determining step and is independent of the layer thickness dp. With longer migration times the partition coefficient also plays a deciding role through the a value because for a << 1 (K >> l), mL..u/mp,m+ a and subsequently only a very small fraction of mp,omigrates into L (Eq. 7-50) (Fig.7-11).
Influence of difision in food The diffusion coefficient in the filled product must be taken into account in liquids that are not well mixed and in viscous and solid foods. This is done through the definition of a further dimensionless parameter p:
Transport rqiintions m r l their solutions
209 (7-56)
which, in addition to the parameters K and DP,contains the diffusion coefficient of i in the food. This dimensionless parameter can be combined with the approximation formula in equation (7-54) in the following way: (7-57) From this expression two limiting cases can be derived: 1. Where DL >> Dp and K 5 1,then p/(l+ p) + 1 and Eq. (7-57) goes to Eq. (7-54). This means that for high diffusion rates in the food, the rate of migration is determined by diffusion into packaging. The same result is obtained for DL DP and K << 1 meaning for approximately equal diffusion coefficients of i in L and P that transport through the packaging determines the rate of the whole process if i dissolves much better in L than in P. The flux of i through the unit surface area for equal diffusion coefficients is directly proportional to its concentration. 2. Where DL < DP and K > 1, then p/(1+ p) + p which in this case gives the following expression instead of Eq. (7-57):
=
(7-58) Here the migration rate of i in the food is determined by the value of the diffusion coefficient in the food as well as by the partition coefficient. The concentration c L , ~of migrants that are poorly dissolved in the food (K > 1) increases more slowly than when they are more easily dissolved. The exact expression for the differential equation (7-12) that takes into consideration the diffusion in food and finite values for Vp and VL is extremely complicated. The extensive calculation required for the exact expression does not justify its use when one compares the accuracy achievable in practice with the errors or deviations resulting from the use of the approximate formula (Reid et al. 1980).
7.2.5 Diffusion through a liquid boundary layer With large K values, that is low solubility of component i in a liquid food, the material transport through A can also be determined from the contribution of diffusion in L under conditions of thorough mixing. Van der Waals attractive forces between the package surface and the molecules of L in intimate contact with P lead to the formation of a thin but immobile layer in which the diffusion coefficient of i in L, DL, controls mass transport (the Nernst diffusion layer). If diffusion through the stagnant boundary layer determines the rate of transport through A for the system, then one can assume a constant, location-independent concentration cp in P. The partition equilibrium is assumed to be reached on the boundary area between P and L at x = 0 and consequently K = cp/cL(0).If one lets the thickness of the diffusion layer in L next to the surface of P be lL and if L assumes a constant concentration of cL, then one can assume a constant material transport flux through the boundary layer for short time intervals that follows Fick's first law and the contribution of the flux to time t is expressed according to Eq. (7-16):
210
Piringer
(7-59) Because up to time t: (7-60)
and CL =!EL “L
one obtains from Eq. (7-59), considering the ratio mp,o/mnc = (1 + a ) / a according to Eq. (7-48) and the definition of a (Eq. 7-37) and because Vp = A . dp: mt (1
+ 41
(7-61)
and after several rearrangements one finally obtains: d(mt/mx) dt
-
D mp.O K d i k m,
(1
- Z.!L
mx)
(7-62)
with the solution: %= mX
1
-
exp
(-0t)
(7-63)
where: (7-64) For short times if mate solution: %c%(T.
mm
(T
.t << 1 the following equation can be used as a good approxi-
t
(7-65)
The determination of (T in Eq. (7-63) is carried out by plotting In (1 - m,/m,) versus t. The slope of the line is then -o (Chang et al. 1988). If diffusion in the packaging determines the rate of migration, there is a deviation from linearity in the plot (Fig.7-12).
7.2.6 Surface evaporation A substance diffusing through the packaging towards the external environment will enter the atmosphere in the absence of a barrier layer. Water or aroma loss through permeation, and drying of a printed film by evaporation of the residual solvent are common examples of this process. In cases where the substance reaching the surface has a very low vapor pressure, e.g. a plasticizer, the rate of evaporation can be slower than the rate of diffusion through the packaging, thus determining the rate of the entire process. At very low evaporation rates the entire process can reach a standstill or lead to “sweating” in the case of low solubility of the plasticizer in the plastic. It is also possible to have the reverse process whereby a substance condenses out of the atmosphere on the package surface, e.g. water, with subsequent diffusion into P. If the packaging surface (or also that of the food) is dry, i.e. the surface has a lower water partial pressure than that in the gas phase G, then water can be absorbed.
Trrinsport equations and their solutions
I
I
21 1
I
In order to mathematically describe the evaporation and condensation processes, the simplifying assumption is used that the rate of material transport through the surface is directly proportional to the difference between the concentration cA,pon the package surface at that time and the concentration c ~in G . in~ equilibrium with the partial pressure of the substance in the atmosphere. Using this assumption one obtains the boundary condition for the surface at the location x = 0: -Dp
2
= k (CA,G
-
CA,~)
(7-66)
with the proportionality constant k. If C A , ~ ; > C A , ~condensation will take place and if CA,G < C A . ~then evaporation will take place.
212
Piringer
The general solution for this problem in the form of the dimensionless ratio mt/mnc according to Crank is:
(7-67) d
k
with L = L. DP
Values of the positive roots of the equation p tan p = L are given in Table 7-3. m, is the amount of material taken up by the packaging or evaporated from the surface up to time t and msc is the corresponding amount at equilibrium. In Fig. 7-13 the ratio of m,/m, is given as a function of the dimensionless quantity (Dp t/d;)li2 for various L values. In the absence of evaporation, the curves show a linear increase at the beginning of diffusion (Fig. 7-11) while the obvious curving shown in Fig. 7-13 for small k values is caused by the slower evaporation process. Table 7-3: Roots of ptanP=L. ~
L
PI
P2
P3
Ps
06
0.00
0.0000
3.1416
6.2832
9.4248
12.5664
15.7080
0.01
0.0998
3.1448
6.2848
9.4258
12.5672
15.7086
0.10
0.31 11
3.1731
6.2991
9.4354
12.5743
15.7143
0.20
0.4328
3.2039
6.3148
9.4459
12.5823
15.7207
0.50
0.6533
3.2923
6.3616
9.4775
12.6060
15.7397
1.00
0.8603
3.4256
6.4373
9.5293
12.6453
15.7713
2.00
1.0769
3.6436
6.5783
9.6296
12.7223
15.8336 16.0107
P4
5.00
1.3138
4.0336
6.9096
9.8928
12.9352
10.00
1.4289
4.3058
7.2281
10.2003
13.2142
16.2594
100.00
1.5552
4.6658
7.7764
10.8871
13.9981
17.1093
1S708
4.71 24
7.8540
10.9956
14.1372
17.2788
cc
0
2
4 u
dP
6
Figure 7-13: Sorption or desorption curves in the valid range of Eq. (7-66) for different L-values
Transport equations and their solutions
213
7.2.7 Permeation through homogeneous materials Steady state permeation which follows Fick’s first law has been previously described in Eq. (7-16). Assuming the concentration of i in P has a constant value cp.1 at the surface (x = 0) and has a constant value C P , ~at the other surface (x = dp) and at the beginning of permeation the concentration in the inside of P has the value cp.0 (t = O), then a nonsteady state of diffusion will take place leading to a change in the concentration cP.[ within P. For simplification one can set cRo= 0 and cr2 = 0. The resulting amount of mass diffusing through the package up to time t is then given as: mt = A dp cp,l
(7
-
5 C [g exp(-Dp XI
-
n2 n2 t/d$)
n = l
This equation becomes asymptotic to the straight line: (7-69) as t
---f
00.
The intersection of this straight line with the t-axis at location 0 is: (7-70)
This is Barrer’s equation for determining of the diffusion coefficient using permeation measurements (Fig. 9-1). The steady state permeation flux is given by the slope of the straight line (7-69): (7-71) This expression is identical to Eq. (7-16) for
= 0.
7.2.8 Permeation through a functional barrier Let us consider a plain sheet of a laminate made of a solute containing core layer (P) and a virgin layer (B) of the same polymer type (Piringer et al. 1998). The thickness of P and B are a and b, respectively, and d = a+b. The virgin layer is in contact with a liquid layer (L). The thickness of the virgin layer (B) is such that it acts as a barrier against the diffusing solute out of the core layer (Fig.7-14). When the liquid L comes in contact with the laminate, the following two extreme situations can occur: ( i ) The solute is homogeneously distributed in the core layer with the concentration C’~,(,(W/V) or cP.(,(w/w)with the density pp of the polymer. The concentration of the solute in B, cg.0, is 0. (ii)The solute is already homogeneously distributed in the whole laminate with cp,,, the equilibrium concentration, that means cp,, = cp = CB = cp.oa/(a+b)= cp,Oa/d. The starting point for modeling permeation (migration) to the liquid is the second case (ii). This is because it represents the well-studied diffusion of a solute from a polymer of limited volume, Vp, into a stirred solution of limited volume, VL. A suitable equation for all of these cases is Eq. (7-51), where cp,o= cp,,.
214
Piringer
Let us consider the laminate system for situation (ii) with a >> 1 and a very short contact time t = ti. This means the initial solute concentration in the vicinity of x=d at t=O is cp=cp, and cL., 2 0 (Fig. 7-14a). This illustration is the case of a system with diffusion between two semi-infinite media (Crank, 1975) for which Eq. (7-51) reduces to Eq. (7-54). A more realistic situation for diffusion in a laminate is illustrated in Fig. 7-14b, which shows the solute concentration profile in the barrier layer after a short contact time t=tl. In this illustration the concentration profile of the solute just reaches the polymer/liquid interface and cL.t 2 0. If we now consider a similar case with a semi-infinite polymer system with the initial solute concentration (cp,,) at the distance x 5 x, = a+b/2 and cp=O at x>xo and t=O (Fig.7-14c), then the possible concentration profiles for the three different times, t d l , t=tl and t>tl can be illustrated in Fig. 7-14d. If we assume a mass transfer through the interface A at X = X I at t=tl in Fig. 7-14d, then mp,,/A = 0.5cp.,pp(d-xl), which corresponds to mp.,/A = cP.epp(xo-a) = cp.,ppb/2 in Fig. 7-14c. If we combine this result with Eq. (7-54) for t=tl, then we obtain the time (7-72)
a)
) c,=
0
A
0
C X - -
a
d
a
d
1-0
:\-A
0
Figure 7-14: Illustration of the mass transfer through a layered package.
I - t,
Trurisporr equations and their solutions
215
If we allow diffusion to continue until t=t2>tl, then under the same assumptions of a semi-infinite system, the mass transfer during At = t2-tl is (7-73)
As mentioned above, the real concentration of the solute in the laminate at the first moment of IaminateAiquid contact lies between the two extremes (i) and (ii). Let us now consider the special case shown in Fig. 7-14b, where the front of the solute just reaches the barrier/liquid layer interface B/L. By comparing Figure 7-14b with Figure 7-14d, we see similar situations are illustrated. Therefore, using Eq. (7-72) and the notations d-xl = b and t l = 0 , a time 0 = (n/16)(b2/Dp) is defined, which is a little greater than the well-known “time lag” = b2/6Dp. If such a system comes into contact with a liquid-phase L, then the mass transfer after the time At=t2-O=t that results from Eq. (7-73) is:
y -fi +,ppjDP( -
dim -
&)
(7-74)
The specific case in Figure 7-14b and Figure 7-15a can be considered as a general reference case for all other practical cases between the extremes (i) and (ii). Depending on the degree of solute diffusion into the barrier layer before it comes in contact with the liquid-phase L, a fictive time, O’, which is shorter (Fig. 7-1%) or longer (Fig. 7-15c) than 0 described in Figure 7-1Sa, can be determined. By relating
a)
:
t A
0
a
d
a
d
t-0
C X - -
0 --X--,
Distance Figure 7-15: Illustration of the relative mass transfer for different amounts of contamination of the barrier layer.
216
Piringer
this 0' to 0, a relative time can be defined which is a measure of the efficiency of the barrier layer B. The value of 0' can be deduced from the relation in Eq. (7-75), were
or
(7-75)
DP is the diffusion coefficient of the solute at some temperature (T*) for time t*, for example, the extrusion temperature of the laminate, where the diffusion of the solute into the barrier layer is most significant. Dp is the diffusion coefficient of the solute in the polymer at the temperature during the contact with liquid L. By using the relative time 0, instead of 8 and the general valid Eq. (7-51) instead of Eq. (7-54), a final equation for the migration of the solute from the core layer P through the barrier layer B after the contact time t can be written similar to the form of Eq. (7-51):
x
2a( 1+a)
(7-76)
n= 1
with
(7-77) and cP.e = CP.O
& = CP,O ad
(7-78)
In the extreme case (ii) of complete diffusion of the solute into the barrier layer B, O,=O, Eq. (7-76) reduces to Eq. (7-51). In the following example an application of the above treatment in an actual case is shown (Piringer et al. 1998). Films of coextruded polyethyleneterephthalate (PET) (pp = 1.4 g/cm3) with a symmetric three-layer structure were produced in which the core layer P (320 pm thick) contained chlorobenzene as a contaminant with the initial concentration, cp,o = 104 pg/g. The PET films which were 400 pm thick, had two barrier layers B (40 pm) of virgin PET. The films were obtained by coextrusion at about 270°C during about 1 second. After cooling the films were stored a few days at room temperature and then the amount of migration was measured into isooctane at 50 "C. The migration of the contaminant into B during the storage period was neglected due to the very low diffusion rate at room temperature. In Table 7-4 the measured migration amounts, mF.,/A, are shown together with the calculated values using Eq. (7-76). The last column contains the calculated migration amounts from a film (d = a+b = 160+40 = 200 pm) in which the contaminant was uniform distributed at the equilibrium concentration, cp,, = 83 yg/g. The symmetric structure allows calculation with only one half of the total film thickness. The measured diffusion coefficient of chlorobenzene in PET at 50 "C is Dp = 2.13E-13 cm2/s and the assumed value at 270 "C (Chapter 15) is DG = 7.1E-7 cm2/s.
Tmnsport equations and their soltrtroi~s
217
Tahle 7-4: Migration (pgidm') of chlorohenzene into isooctane at 50°C. Time (days)
Measured
Calculated
10
< 0.5
0.3
5.6
39
0.8
1.2
11.o
69
2.0
2.2
14.8
2.9
17.0
110
3.0
3.4
18.7
130
4.0
4.0
20.2
91
Calculated for b=O
From the above results one can see that a functional barrier limits the amount of migration of a component from the package to food-simulating liquids. But when using a coextrusion process to create a functional barrier, the assumed virgin layer becomes contaminated from components of the core layer (recycled polymer layer) during manufacturing. These effects must be considered if reliable predictions of migration are to be obtained (Chapter 10). A solution obtained with numerical mathematics is also shown in chapter 8.
7.2.9 Permeation through a laminate Diffusion through a barrier layer is a special case of diffusion through a laminate film composed of several layers with different thicknesses and diffusion coefficients. The mathematical treatment of the non-steady state case is complicated. The steady state permeation case allows the overall transport to be simply treated. Let n films with thicknesses dP1, dP2,..., dp, with corresponding diffusion coefficients Dp1, Dp2, ..., Dp, be bound together in a laminate. Because in steady state, the flux J of the diffusing substance i is the same through every individual component of the laminate, one obtains an expression for the concentration gradient:
+
R2
+
... Rn) J
(7-79)
with the resistance R 1= d,l / Dpl etc. The total resistance related to the diffusion is then the sum of the individual resistances and the total flux is practically determined by the layer with the smallest diffusion coefficient.
7.2.10 Concentration dependence of the diffusion coefficient At dilute concentrations DP is usually constant. When swelling is caused by either fat, water, essential oils or other organic components found in the product then DP can become concentration-dependent in the region of a boundary layer in P. In such cases the diffusion equation (7-12) is no longer valid and the general form of the diffusion equation (7-11) must be used.
218
Piringer
I
lo-'
El
10-4
10-5
1r4
10-3
IO-~
lo-' t Ihl
loo
10'
1 02
Figure 7-16: Migration from a system with swelling under various conditions (Chang 1988). Dp.0 = 1 6 5 1 0 cm2/s,Dp = 10E-10 cm'ls: t,, = 0; vo: E-S cmls in A. E-6 cmis in B, E-7 cmk in C and E-8 cmis in D.
In this case D = D(c) is a function of the concentration c of the substance causing the swelling. The literature holds numerous recommended solutions for treating such cases, none of which are universally applicable. A general way for solving problems of this type is to use numerical integration in combination with a representative model suitable for the specific case. In the initial stages when the food or another product is brought in contact with the package (t = 0), the migration of the substance i from P into L takes place with a constant DP because the swelling processes require a certain amount of time before they affect the migration process of i. After this initial contact phase the swelling front, XQ,moves into P with a certain speed vQ (Fig. 7-16). In the region x > XQ the diffusion of i takes place with DP and in the region x < XQ with D ~ >QDp. The swelling front XQ moves into P with the speed vQ: XQ
= VQ (t
-
to)
(7-80)
whereby to > 0 signifies the initial contact phase before swelling takes place. The result of such a process can be qualitatively seen in Fig. 7-14 (Chang et al. 1988).
7.2.11 Diffusion and chemical reaction When a first order irreversible chemical reaction (e.g. oxygen absorption and oxidation) takes place simultaneously with diffusion in food for example, then one obtains the following expression from the general mass transfer equation (7-10): (7-81)
Trrrnsport equations and their sokitions
219
where k is the reaction rate constant. If the reaction takes place in a relatively thin layer near the surface or boundary layer of L to P then one can consider L as a half open medium (infinitely thick). This leads to a considerable simplification of the mathematical treatment. Furthermore, letting cL.0 be a constant surface concentration one obtains the absorbed amount m, up to time t: mt = A CL.O (DL/k)'l2[(k t
+ i)erf (k t)1/2 +
(k t/Jc)'l2 e-
'1
(7-82)
For large k . t values the erf (k .t)1'2 goes to one and: mt = A
C L . ~(DL/k)'/*(t
+ A)
(7-83)
that means m, increases linearly with t. For very small values of k . t one obtains:
(7-84)
When k + 0 only diffusion without reaction takes place: mt
E A C L , ~(DL t)II2
(7-85)
Because the diffusion process and the reaction occur in the same medium L the ratio of A N L does not come into consideration. References Carslaw H. S.. Jaeger J. C. 1959, Conduclion c!f'Henr in Solids, Clarendon Press, Oxford. Chang S.-S., Guttman C. M., Sanchez I. C.. Smith L. E.. 1988 in: Hotchkiss J. (ed), Food and Packaging Interactions, ACS Symposium Series No. 365. Washington. Crank J. 1975. Mathematics of Diffusion, Znd ed.. Clarendon Press. Oxford University Press, Oxford. Kreyszig E. 1993, Advanced Engineering Mafhernnrics,7'h ed., John Wiley & Sons, Inc. New York. Piringer O., Franz R.. Huber M., Begley T. H., McNeal T. P,1998, .I Agric.& . Food Cheni. 46,15321538. Reid R. C., Sidman K. R., Schwope A. D.. Till D. E., 1980. Ind. Eng. Chem. Prod. Res. Dev. 19,580-587.
Reactivity in Molecular Crystals Edited by Yuli Ohashi Copyright @ K d a o r h a Ltd .Tokyo. 1999
8 Numerical solutions of the diffusion equation Titus A . Beu
8.1 Why numerical solutions? Despite the large number of analytical solutions available for the diffusion equation, their usefulness is restricted to simple geometries and constant diffusion coefficients. The boundary conditions, which can be analytically handled, are equally simple. However, there are many cases of practical interest where the simplifying assumptions introduced when deriving analytical solutions are unacceptable. For example, the diffusion process in polymer systems is sometimes characterized by markedly concentration-dependent diffusion coefficients, which make any analytical result inapplicable. Moreover, the analytical solutions being generally expressed in the form of infinite series, their numerical evaluation is no trivial task. That is, the simplicity of the adopted models is not necessarily reflected by an equivalent simplicity of evaluation. To obtain solutions to the diffusion equation, which more realistically models practical situations (where, for example, the diffusion coefficient or the boundary conditions are non-linear), one must resort to numerical methods. Basically, these imply restricting the solution of the diffusion problem to a set of gridpoints, conveniently distributed within the integration domain, and approximating the involved derivatives by discrete schemes. Such an approach leads to a system of linear equations, having as unknowns the solution values at the gridpoints. The linear system can be solved in principle by any classical method, even though, for the sake of computational efficiency. more specialized methods are recommended. The numerical discretization methods affect the essence of the physical model much less than analytical approximations do, allowing for much more complex diffusion problems to be treated.
8.2 Finite-difference solution by the explicit method We consider for now the one-dimensional diffusion equation, with constant diffusion coefficient D:
Such an equation is useful for describing the time evolution of the concentration profile of some diffusant across a plane sheet of given thickness L and infinite transverse extension. In order to model a particular experimental arrangement, this equation must be solved in conjunction with certain initial and boundary conditions. We will consider that Eq. (8-1) is subject to the initial condition: c(x, to) = c"(x),
x E [O, L]
(8-2)
222
Beu
which means that the concentration profile at the initial moment to is given over the entire sheet thickness. However, the solution of the initial value (or Cauchy) probZem defined by Eqs. (8-1) and (8-2) cannot be uniquely determined unless supplementary boundary conditions for t > to are specified. For simplicity, we will assume that the concentration values at the outer surfaces of the sheet are constant for any t 2 to: c(0, t ) = c;,
c(L, t) = CL 0
(8-3)
Such boundary conditions, specifying the values of the solution, are known as Dirichlet houndury conditions. The so-called Neumann boundary conditions, which define the derivative of the solution on the boundaries, form another important category, considered among others later in this chapter. The method we use to approximate the solution to the problem (8-1) to (8-3) is based on finite difference schemes for the derivatives involved by the diffusion equation (and, in general, by the boundary conditions, too). The straightforward approach is to choose equally spaced points along the x- and t-axes, covering the space-time integration domain by a regular rectangular grid (Fig. 8-1). Denoting by h and At the corresponding mesh constants (with the stipulation that L/h is an integer), the gridpoints are defined by the discrete coordinates: xi = (i - l ) h ,
i
= 1 , 2 , . . . , M:
(8-4)
tn=nAt,
n = 0 , 1 , 2,...
Here M represents the number of spatial gridpoints and the spatial mesh constant is given by: h = L/(M - 1).
(8-5)
We use the notation c: = c(xi, t,). The time derivative of c at point (xi, tn) can be obtained from its Taylor series in t for constant x = xi:
Taking the linear approximation and expressing the first order time derivative, one obtains:
+ O(At).
(8-7)
O(At) signifies that in the above approximation the leading term that was neglected is of the order At (we have divided (8-6) by At to get (8-7)). This is the socalled Euler forward-difference scheme. While it is only first-order accurate in At, it has the advantage that it allows for the quantities at timestep n 1 being calculated only from those known at timestep n. The discrete approximation for the second order spatial derivative ( $ c / & ~ ) ~ , ,at x = xi results in a similar manner, namely by expressing the concentrations at the neighboring gridpoints xi-1 and X ~ + Ifrom the Taylor series in x at constant t = t,:
+
223
Nirtnericol solutions of’the diffiision equation
explicit
CrankNicholson
x,= 0
implicit
x,=L
Figure 8-1: Space-time grid for the one-dimensional diffusion equation. evidencing the explicit forward-difference. implicit backward-difference and Crank-Nicholson discretization schemes.
On adding we find
(2)
i, =
c+ : I -2c: +c;- I hz
+ O(h2)
(8-9)
This second order approximation is a centered-difference scheme, since it expresses the spatial derivative at point i by means of data from symmetrically distributed points. All the implied information is known at timestep n. By substituting relations (8-7) and (8-9) in Eq. (8-1), one obtains the following finite-difference approximation to the diffusion equation at point (xl,tn): ,n+l -cn I
At
’ = D
c;+l -2c;+c;-l h2
(8-10)
Having in view only the way the time derivative was approximated, this is the forwrrrd-difference representation of the diffusion equation and it is of order O(h2 At). Slight rearrangement yields a formula, which expresses the time-propagated solution cy+’ for any interior spatial gridpoint in terms of the other quantities known at timestep n: c!l+l = Ac?,-I (1 -2A)c) +Aclntl. (8-11) i = 2 , 3,..., M - 1 ,
+
+
where: Dt
A = p
(8-12)
224
Beu
The concentration values on the boundaries, c;+' and cL++',generally result from the boundary conditions and, within the simple adopted model, are seen to be constant: (8-13) Since the solution of Equation (8-11) propagated at timestep tn+l is expressed solely in terms of data from timestep t,, not requiring any previous information, the forward-difference scheme is said to be explicit, and its essence can be extracted from Fig. 8-1, too. The explicit nature of the recursive process described by Eqs. (8-11) to (8-13) becomes even more apparent if using matrix notation for the involved linear system: n = 0 , 1 , 2 ,....
cn+l = B . c n ,
(8-14)
The components of the column-vector c" are the values of the solution from all spatial gridpoints at timestep t,: (8-15) and the propagation matrix B has tri-diagonal structure, i.e., except for the main diagonal and the neighboring upper and lower co-diagonals, all elements are equal to 0 1 0 h 1-2h
0-
h
B=
I
h
1-2h 0
0
(8-16)
h 1-
When solving the one-dimensional diffusion equation (8-15) by the explicit forward-difference formulation described above, one is faced under certain conditions with severe numerical instability problems. This means that, instead of yielding a relatively smooth spatial profile, the algorithm develops oscillations, which grow exponentially in time, "unweaving" the solution and making it unusable. This critical behavior occurs when the used timestep exceeds a certain upper limit for a given spatial mesh constant and is caused by the increasing dominance of round-off errors. In order to emphasize the critical relationship between the timestep and the spatial step, we consider the one-dimensional diffusion equation with constant diffusion coefficient D = 1: ac -
8%
at
Q
-
T
x E [0,1], t > 0,
(8-17)
subject to the simple boundary conditions: c(0, t) = c(1, t)
= 0,
and initial condition:
t
>0
(8-18)
Niinierical soliltions of the diffiision eqiicrtiori
0.16
__
225
numerical solution
0.14 0.12 0.10 c,
0.08 0.06
0.04 0.02 0.00 0.0
0.2
0.6
0.4
0.8
1.o
Y
Figure 8-2: Exact and numerical solutions obtained by the explicit method for the Cauchy problem (8-17) to (8-19). by using the spatial step h = 0.05 and the timestep At = 0.00125.
c(x,0) = sin(nx), x E [0,1].
(8-19)
It can be easily verified that the analytical solution to this problem is: c(x, t) = e-x2t sin(7cx)
(8-20)
We investigate the behavior of the numerical solution to problem (8-17) to (8-19) at the moments t = 2.0, t = 2.5 and t = 3.0 for two different timesteps, by using the constant spatial step h = 0.05. Figure 8-2 shows the spatial concentration profiles obtained by using the timestep At = 0.00125, corresponding to h = 0.5 ( h is defined in Eq. (8-12)). As one may notice, apart from the inaccuracies caused by the finite spatial step size, the profiles resulted from the numerical solution (depicted with dotted lines) fairly reproduce the analytical results (continuous lines). Figure 8-3 shows the spatial concentration profiles obtained with the slightly increased timestep At = 0.0013, corresponding to h = 0.52. Even though the solution at t = 2.0 can hardly be distinguished from the one obtained with At = 0.00125, it is apparent that at t = 2.5 instabilities begin to develop and they dominate the solution entirely at t = 3.0. Hence, a seemingly insignificant change in the timestep leads to a dramatic qualitative change of the solution. This indicates that the value h = 1/2 is critical, and that it separates two domains of numerical parameters characterized by different behavior of the solution: for h < 1/2 the propagation of the solution is stable, while for h > 1/2 it turns out to be unstable.
226
Beu
0.16
-- numerical solution 0.14
0.12 0.10 0
0.08 0.06
0.04 0.02 0.00 0.0
0.2
0.6
0.4
0.8
1.O
Y
A
Figure 8-3: Exact and numerical solutions obtained by the explicit method for the Cauchy problem (8-17) to (8-19) , by using the spatial step h = 0.05 and the timestep At = 0.0013.
8.2.1 von Neumann stability analysis An intuitive way of investigating the stability properties of a finite-difference scheme is the von Neumann stability unulysis, which we briefly outline as follows. The von Neumann analysis is b c a l , being based on the assumption that the coefficients of the difference equation are so slowly varying in space and time as to be considered constant. Under such assumptions, the eigenmodes (the independent solutions) of the difference equation may be written in the general form: u: = t"exp[tk(i
-
l)h]
(8-21)
1 stands for the imaginary unit (not to be confused with the spatial index i), k is the spatial wave number, which can take any real value, and 6 = C(k) is the so-called amplification factor, which is a complex function of k. Apart from the spatial details, the essential feature of the eigenmodes is their time dependence through the timestep index n, as integer powers of the amplification factor. The time propagation of the solution is considered to be stable if the amplification factor satisfies the condition:
since no exponentially growing modes of the difference equation can exist under such circumstances.
Nllnzericnl solutioiis of the difficsiori eqtrntion
227
In order to express the amplification factor for the forward-difference representation of the one-dimensional diffusion equation, one has to replace the general form (8-21) of the eigenmodes into the difference equation (8-11):
5 = hexp(-tkh) + (1 - 2h) + hexp(tkh). By combining the exponentials and employing the trigonometric identity 1 - cosx = 2sin2(x/2),one obtains for the amplification factor:
5 = 1 - 4hsin2(kh/2)
(8-23)
Use of the von Neumann stability criterion (8-18) leads to the condition:
O
(8-24)
which, taking into account the definition (8-12) of h, becomes: 1 h2 at < zB
(8-25)
The significance of this result is that the timestep At insuring the stability of the algorithm is limited by an upper bound, which is proportional to the diffusion time across a cell of width h. This makes the explicit scheme, characterized by forward time differencing, conditionally stable and proves that the value h = 112 is indeed critical.
8.2.2 The Crank-Nicholson implicit method To obtain an algorithm that is unconditionally stable. we consider an implicit discretization scheme that results from using backward finite-differences for the time derivative. The corresponding difference equation is most conveniently obtained by approximating the diffusion equation at point (xi, tn+l): (8-26) Analogous to the forward-difference method previously discussed, it is only firstorder accurate in at. The only formal difference with respect to the forward-difference equation (8-10) appears to be the fact that the space derivative is evaluated at time t,+l, not at time t,. By rearranging the terms in (8-26), the following system of linear equations results:
-hc;:;
+ (1 + 2h)c:+'
- hcn+' l+1
-
ci" '
i = 2 . 3 . . . . , M - 1,
(8-27)
where, as before, h = Dt/h2. By contrast with the forward-difference method, the propagated concentrations c:+' cannot be explicitly expressed, but result from solving the above set of simultaneous linear equations at each timestep. For this reason, the discussed backward-difference scheme is said to befidfy inipficit.The implicit nature of this method can also be observed from Figure 8-1,which indicates the data involved.
228
Beu
By using matrix notation, the linear system (8-27) can be written: n = 0 , 1 , 2 ,...,
A.c"+l =c",
I
(8-28)
with matrix A having tri-diagonal structure:
1
0
0 -
-1 1 + 2 h -A
A=
0
(8-29)
-h
1+2h 0
-a 1 -
It is apparent from the first and last rows of this matrix, that again the simple Dirichlet boundary conditions, Eq. (8-3), have been considered. Since h > 0, the matrix A is positive definite and diagonally dominant. For solving system (8-28), the very efficient Crout factorization method for linear systems with tri-diagonal matrix can be applied (see Press et al. 1986, Section 2.4). The implicit backward-difference algorithm does not show the stability problems encountered in the case of the explicit forward-difference method, and this results immediately by analyzing the expression of the amplification factor:
'
1 = l+4hsin2(kh/2)'
(8-30)
which obviously satisfies the von Neumann stability criterion lC(k)l < 1 for any stepsize At. Hence, the backward-difference scheme is unconditionally stable. Provided the solution of the differential equation satisfies the usual differentiability conditions, the local truncation error of the method is of the order O(h2 + At). The weakness of this method is, however, the low order of the truncation error with respect to time, requiring comparatively much smaller time intervals than the spatial stepsize. A second order method with respect to both space and time can be derived by approximating the diffusion equation at timestep tn+l/2= t, + At/2 and employing a centered-difference scheme for the time derivative, too. Considering the Taylor series in t at constant x = xi:
(8-31) on subtracting we find the time derivative sought:
(8-32) The spatial derivative at timestep tn+1/2 can be approximated by taking its average over the timesteps t, and t,+l. Hence, the discretized diffusion equation takes the form: C?+' -c? c;;-2c;++ ' cr:/ +(cy+, -2c:+c:J I = D (8-33) At 2 h2
Niitnericril solutions of the diffrision equation
229
This is the so-called Crank-Nicholson scheme and, formally, it could have been obtained by simply averaging the explicit forward-difference and implicit backwarddifference schemes. By conveniently grouping the terms, the following system of linear equations results: -hcn+l
1-1
+ (1 + 2h)c:+'
hc?1-1
-
1
1+1
+ (1
+
24c; hC,?,l, i = 2 , 3, . . . , M - 1 , -
(8-34)
with: (8-35) The discretized system (8-34) can be represented in matrix form as:
A.c"+' = B . c n , n = 0 , 1 . 2 ....
(8-36)
where matrices A and B have tri-diagonal structure and are given by Eqs. (8-29) and (8-16), respectively. Since A is positive, definite and diagonally dominant, it is nonsingular, thus allowing for Crout factorization method for tri-diagonal linear systems to be applied to obtain c"+' from c" for any n = 0 , 1 , 2 , . . .. It has to be noted that the evaluation of the right-hand-side members of system (8-36) requires a little more work than in the case of the fully implicit scheme, implying the multiplication of the tri-diagonal matrix B with the "old" solution vector c". The amplification factor resulting from equation (8-34) is:
'
1 -4hsin2(kh/2) = l+4hsin2(kh/2)
(8-37)
and, consequently, the Crank-Nicholson method turns out to be unconditionally stable. Due to its stability and satisfactory order of convergence O(h2 + (At)*), the Crank-Nicholson scheme is the recommended approach for any simple diffusion equation. In order to demonstrate the beneficial influence of the higher order accuracy with respect to time of the Crank-Nicholson method, we consider again the initial value problem Eqs. (8-17) to (8-19), which is solved both by the fully implicit and the Crank-Nicholson schemes. We investigate the numerical solution at time t = 3.0 by using the constant spatial step h = 0.05. Figure 8-4 shows the spatial concentration profiles obtained by using the timestep At = 0.025. which is 20 times larger than the largest value to insure the stability of the explicit method (see Fig. 8-2). As one may notice, the profile yielded by the Crank-Nicholson algorithm (depicted with long dash) agrees very well with the analytical result (continuous line) even for the large timestep considered. By contrast, the solution obtained by the fully implicit method (short dash) departs quite substantially from the exact solution. Hence, it should be obvious that the stability of the fully implicit scheme (absence of oscillations) does not automatically also guarantee high accuracy.
230
Beu
0.08
0.06
u 0.04
0.02
0.00
0.0
0.2
0.4
0.6
0.8
1 .o
X
Figure 8-4: Comparison of the numerical solutions obtained by the fully implicit and Crank-Nicholson methods for the Cauchy problem (8-17) t o (8-19).The spatial step h = 0.05 and the timestep At = 0.025 have been used.
8.3 Spatially variable diffusion coefficient If the diffusion coefficient is spatially variable, the one-dimensional diffusion equation has the form: (8-38) The correct way to differentiate this equation relies on the following centereddifference approximation of the spatial derivative at timestep t,:
(8-39)
The midpoints xi+1/2 = (xi + xi+1)/2 and the corresponding values of the diffusion coefficient Di+1/2 = D(xi+l/2) have been introduced to ensure appropriate centering of the implied derivatives. A convenient approximation for Di+]l2 results from considering the average of the values at the neighboring gridpoints: ~ i + 1 / 2= i(Di + D i + l )
(8-40)
In the case of unequal spacing of the spatial gridpoints, Eq. (8-39) can be generalized to give:
Nirniericn/ solutioris of the diffirsion equation
231
Application of the Crank-Nicholson method based on the spatial difference scheme (5.39) results in the following discretized form of the diffusion equation:
(8-41)
Rearrangement of terms leads to the system of linear equations:
(8-42)
A.1 --4 t 2P
(8-43)
The system (8-42) should be completed with appropriate equations resulting from the boundary conditions and it can be solved, in principle, by the same factorization method of Crout for systems with tri-diagonal matrix. When the diffusion coefficient depends not only on the spatial coordinate but also on the local concentration, the discretization of the diffusion equation proceeds in a similar manner, except that one has to solve at each time step not a system of linear equations, but a quite complicated set of coilpled non-linear equations.
8.4 Boundary conditions In the treatment of explicit and implicit difference methods, we have used Dirichlet type boundary conditions, for the sake of simplicity, which specify the values of the solution on the boundaries. A more general type of boundary condition can be defined in the form of a linear combination of the solution and its derivative. Considering in particular the left boundary, such a mixed boundary condition can be written:
[a+.
t)
+ B i)c(x.t)
I
x=O
=Y
(8-44)
For p = 0 this is a Dirichlet type condition, while for a = 0 it is a Neumann type condition. a,@, and y may, eventually, be functions of time. A practical example for a mixed boundary condition is the evaporation condition:
ac(x.t) ax ! L O
= a[c(0,t)
-
c,]
(8-45)
where ce is the equilibrium surface concentration. The simplest finite-difference representation of the mixed boundary condition (8-44) may be readily obtained by considering for the spatial derivative the forward-
232
Beu
difference scheme implying the concentrations on the boundary, cp, and at the neighboring interior gridpoint, c;: acf
cn-cn + py =y
(8-46)
However, this approximation is of the order O(h) and, since the difference equations for all discussed (explicit and implicit) propagation methods are O(h2),it is definitely not the best choice. An improved O(h2) finite-difference representation of the boundary condition (8-44) results by approximating the solution in the vicinity of the boundary by the second order Lagrange interpolating polynomial passing through the points ( X I , c?), ( x ~c;), , and (x3, cz) (equally spaced gridpoints are assumed):
q x ,t") = & [(x - x2)(x - X3)CT
-
2(x - x*)(x- x3)c5
+ (x
-
XI)(X
-
x2)cg (8-47)
The interpolation properties of this uniquely defined parabola can easily be verified by direct evaluation for XI, x2, and x3, respectively. The derivative of polynomial (8-47) is given by:
=4 =
2h
[(2x - x2
-
x3)c;
-
2(2x - X I
-
x3)c5
+ (2x
-
x1
-
X2)C?],
(8-48)
and for x = XI,where we wish to approximate the boundary condition, it takes the particularly simple form: (8-49) By replacing this approximation in the boundary condition (8-44), one is left with the supplementary equation:
ac;
+
-3c7+4c;-c; 2h
=y
(8-50)
Adding this equation to the set of difference equations resulting from the diffusion equation no longer preserves the tri-diagonal structure of the system matrix. Indeed, appearing as the first equation of the system, the coefficient of cs does not lie on the principal diagonal or on one of the two neighboring co-diagonals. In such cases, one has to resort to general methods for solving the linear system, such as Gaussian elimination or the LU factorization method of Crout. An absolutely analogous treatment may be applied to the right boundary, for which the boundary condition reads:
(8-51) A third possibility of approximating the mixed type boundary condition, widely used, implies considering a fictitious external gridpoint xg and the corresponding concentration c;. The centered-difference approximation of the boundary condition becomes: acy
+ p c"-c"v = y
(8-52)
Nirnierical solutions of the diffusion equation
233
The unknown (and in principle "useless") value of c; may be eliminated by using the diffusion equation approximated at the gridpoint X I (see Eq. 8-39): (8-53)
+
with D3/2 = (D1 + D2)/2 and D1/2 = (Do Dl)/2 = D1. On replacing ci from (8-52) in (8-53) and by considering the Crank-Nicholson scheme, the following difference equation results: cn+ 1 1 At-
,n+l_,n+l
c L & [ ( D 1/2 + D3/2)
+& [ ( D l p + D3p)
+
*
h
'
7
+ 2D1/2 (ac;+l
B
(ac? - y)]
-
y,]
+
(8-54)
.
which can be rearranged to become the first equation of the system (8-42). A similar treatment may be applied to approximate t h e right boundary condition, which then becomes the last equation of the system. In t h e particular case of Neumann boundary conditions modeling impermeable surfaces ( a = y = 0), the two equations can be cast in the simple form:
(1
+ 2hl)C7+'
-2hh4CF1,
-
2h1c;f' = (1 - 2hl)CY
+ 2hlC!,
+ ( 1 + 2h&"M++' = 2hh4C&p1+ (1
(8-55) -
2h&&
where hi is given by Eq. (8-43). Obviously, these approximations of the boundary conditions preserve the tri-diagonal structure of the matrix of system (8-42). In certain applications, it is convenient to impose (eventually, instead of one of the local boundary conditions) a global condition upon the total amount of diffusant, in the form of an integral over the entire spatial region: L
c(x, t)dx = Q
(8-56)
b Such a normalization condition can be readily discretized by considering, for example, the simple trapezoidal rule for performing the numerical quadrature:
(8-57) The quantity Q might be related, for example, to the total amount of diffusant at the initial moment, but it could equally be a function of time.
8.5 One-dimensional diffusion in cylindrical and spherical geometry There are certain practical diffusion problems, which can be treated most appropriately in cylindrical or in spherical coordinates. In many cases, choosing the natural coordinate system allows for the coordinates to be separated, and one is left with the simpler problem of dealing with one-dimensional diffusion along the radial coordinate. Basically, the only technical complication which arises as compared to the one-dimensional diffusion in Cartesian coordinates treated so far, concerns the approximation of the spatial derivative of the concentration involved by the diffusion equation.
234
Beu
Assuming constant diffusion coefficient, the equation describing the radial diffusion in cylindrical coordinates may be written: (8-58)
In order to approximate its solution, we establish a grid of equally spaced points in the interval [0,R] of the radial coordinates. Denoting the corresponding mesh constant by h, the gridpoints are defined by the discrete coordinates: ri=(i-l)h,
i = 1 , 2, . . . , M
(8-59)
A second order representation of the right-hand side u l Eq. (8-58) at point obtained by using centered-differences for the spatial derivatives:
(Ti,
tn) is
(8-60) A special treatment has to be applied to the central gridpoint rl = 0. The singularity arising in the second term is overcome by imposing the natural boundary condition that the first order derivative vanishes at rl = 0. By introducing a fictitious gridpoint ro = rl - h, this condition may be approximated by the second order centered-difference scheme:
(8-61) This relation is practically useful only to eliminate further occurrences of c;. Still, the second term of the spatial derivative, (l/r)(b'c/&), implies an indeterminate form of the type O/O. Making use of 1'Hospital's rule results in the following representation:
d2 l a c [$ + ;z]r1
,tn =
[2$1
c"-2c"+c" rl .t,
2-
c"--c" =4
(8-62)
Having established the appropriate finite-difference expressions of the spatial derivatives, the diffusion equation may be approximated as follows: c" - c" =4D11-, i=l, at r1.t" h2 (8-63) (2i - l ) ~ r + 4(i ~ - 1)cI (2i - 3)crPl =Di , i = 2 , 3 ,... M - 1 . 5,tn 2(i - l )h
$1
+
The equation for the central point (i = 1) actually plays the role of "inner" boundary condition. The above system should be completed with one more boundary condition for the outer point r M = R. Irrespective of the type of the used time difference scheme (explicit, fully implicit or Crank-Nicholson), the further treatment of the resulting system of difference equations is absolutely analogous to the one developed for Cartesian coordinates. The radial diffusion equation in spherical coordinates may be written for constant diffusion coefficient as:
Nuniericcil soliltions ofthe diffusion equation
235 (8-64)
Following the pattern employed in the case of the cylindrical coordinates, one obtains the following finite-difference approximations:
The treatment of the various types of outer boundary conditions (for r M = R) and of the complete system of difference equations is again analogous to the case of the Cartesian coordinates.
8.6 Multi-dimensional diffusion The extension of the methods described so far to multi-dimensional diffusion problems is straightforward in principle. However, in such an attempt one is faced with a quite considerable increase in computational effort. Let us consider for simplicity the two-dimensional diffusion equation: (8-66) for which we wish to find the solution in the rectangular domain [0,a] x [0,b]. We assume that c(x,y, t) is known over the whole spatial region at t = to, and that it is prescribed on the boundary for any t > to. Applying the Crank-Nicholson scheme to equation (8-66), relative to a space-time grid characterized by the points: xi = (i - l ) h ,
yj
=
(j - l ) h ,
tn = nAt
(8-67)
results in the following difference equation: (8-68)
: and 6 : Here, h = Dt/(2h2) and the second order centered-difference operators 6 are defined by: (8-69)
Whereas in the case of the spatially one-dimensional diffusion, the set of difference equations features a tri-diagonal matrix, the system in Eq. (8-68) can be shown to have a block tri-diagonal matrix, which requires the use of special solving methods. A very powerful method for the solution of system 8-68, widely in use, is the so-called alternating-direction implicit method, which is based on the idea of splitting each timestep
into two substeps of size At/2. In each substep, the concentration is kept constant in one of the spatial dimensions, while in the other one it is treated implicitly: (8-70)
The first equation treats the x direction implicitly, keeping the y direction unaffected. In the second equation, the role of the two directions is interchanged. Slight rearrangement of the system: (8-71)
+
n+1/2 , (1 - h62)cnk' Y 1 J = (1 h6,)Ci.j 2
evidences the great advantage of this method: at each substep it requires only the solution of a tri-diagonal system. Hence, instead of solving at each timestep a system with block tri-diagonal structure, one has to solve two systems with simple tri-diagonal structure. Example 8-1 In chapter 7, section 7.2.8 an example of permeation through a functional barrier is described. Three-layered coextruded PET films were produced in which the core layer (P) was contaminated with chlorobenzene and the outer barrier layers (B) were made with virgin material. During the coextrusion process a partial contamination of the virgin layer occurred. The symmetrical structure of this film leads to a simplified treatment of it as a two layer laminate with the thickness d = a + b = 160 + 40 = 200 pm. For the modeling of this problem with numerical mathematics all parameters given in Section 7.2.8 are used. Starting with the one-dimensional diffusion equation (8-1) the concentration profile, cp versus x and t is presented in Fig. 8-5 for one half of the laminate.
40 -
20 -
\\'
-t = o t=1sec t = 10 days t = 130 days
'h
\\
',
\\
0 100
120
160
140
x
180
(w)
Figure 8-5: Concentration profile for the migration of chlorobenzene in and from an impurified PET core layer into a virgin PET barrier layer and a food simulating liquid F.
From this figure one can see that even for a very short period of time (t near zero) there is a considerable migration of chlorobenzene from the core layer P into the barrier layer B. This can be attributed only to the high temperature (about 270 "C) migration process during the
Nirtnericnl solutions of the diffusion rqiintion
237
coextrusion. After cooling, the laminate was stored at room temperature (very slow diffusion rate) until the migration experiment at 50°C during 130 days. The further contamination of the barrier layer B during the storage (few days) was neglected.
---
Figure 8-6 Concentration profiles, at fixed migration times. of chlorobenzene from an impurified PET core layer into a virgin PET harrier layer and a food siniiilating liquid.
From Fig. 8-6 one can clearly see that the very short (1 s) high coextrusion has an important impact on the migration of chlorobenzene from the core layer towards B and later into F. The subsequent migration in the laminate for 10 days at 50°C produces only a small transfer of the contaminant into B. The time dependence of the amount migrated from the laminate into F is shown in Fig. 8-7. I
20,
4 0
20
40
60
80
100
120
140
t (days)
Figure 8-7: Amount of chlorobenzene migrated at 50°C from the PET laminate into isooctane.
For a relatively long time, about 10 days. the net amount of chlorobenzene migrated from PET into isooctane is very small (nearly zero). In practice this is equivalent to a “time lag” needed by the impurity to reach the outer surface of B. It is interesting to compare this time lag with the one which would correspond to the situation with no contamination of B. In this case the chlorobenzene needs a time lag, 0 = b2/6Dp= 145 days, where b = 40 pm. Hence one
238
Beu
can see from these results that the coextrusion process has a very important impact on the final usefulness of the manufactured PET structure for food packaging applications. The results obtained with the numerical approach are systematically smaller (about 60 % at 130 days) than both the experimental and analytically calculated results shown in Table 7-4. The fact that the numerical solution of the diffusion equation led to smaller mE,/A than the experimental ones can be the result of assuming a too short coextrusion time. Increasing this time only by 50 % leads to a much higher impurification of the barrier layer and consequently to a much shorter migration time lag and to a higher migration rate into F. It should be also noticed that the analytical approach given in section 7.2.8 leads over 130 days to an almost linear increase of m,,/A from zero to about 4 pg d w 2 . This may be an indication that the assumptions made in order to develop the analytical solution for this example led to an overestimation of mF,,/Aat the beginning of the migration process.
Suggested further reading Burden, R.L., Faires, J.D. 1985, Numerical Analysis (Prindle, Weber & Schmidt. Boston). Crank, J. 1975, The Marhernarics of Diffusion(Oxford Science Publications, Oxford). Koonin, S.E., Meredith, D.C. 1990, Compurarional Physics (Addison-Wesley Publishing Company, Inc., Redwood CA). Press, W.H., Teukolsky, S.A., Vetterling, W.T., Flannery, B.P. 1986, Numerical Recipes in C (Cambridge University Press, Cambridge).
Reactivity in Molecular Crystals Edited by Yuli Ohashi Copyright @ K d a o r h a Ltd .Tokyo. 1999
9 Permeation of gases, water vapor and volatile organic compounds Otto Piringer
The processes of mass transfer taking place in a packaging system and their consequences for maintaining food quality form the main emphasis of this book. In this and the following chapters, the physical and chemical aspects of these processes (known also as packaging/product interactions), as well as their measurement and evaluation are treated from a food regulatory point of view. Only the simplest mathematical expressions describing the permeation and migration of substances from the environment, packaging and product are used here. It must be emphasized however that these formulae are as a rule very simplified approximations representing various transport processes. The exact mathematical treatment of interactions, along with their solutions for the corresponding differential equations, appear at first to be very difficult to interpret and awkward to use. Because of their complexity, exact solutions of the diffusion equation must be carried out using either numerical methods (Chapter 8) with the help of a computer or solved analytically in simpler cases (Chapter 7). The use of exact solutions does not in all cases bring significant advantages to the problem’s solution and the additional effort is not always justified when one considers the observed variability of material properties found in practice. However, it is very important to be able to estimate both the applicability of an equation to a particular problem and the errors that can occur when it is used outside this area of applicability (Chapter 7). The term permeation, as treated in this chapter, is understood to mean the transport of a substance through the packaging. The permeation of substances can occur from the package’s surrounding environment into the food or from the packed product into the surrounding environment. The term migration is understood to mean the transport of a substance from the packaging into the product or from the product into the packaging (Chapter 7). The same underlying physical process controls both permeation and migration. These processes include sorption and/or adsorption of the transported substance in the packaging and product, as well as diffusion in and through the boundary layers between the packaging and filled product and between the packaging and surrounding atmosphere. Because glass and metal are impermeable, and paper and cartons are very highly permeable, practically all permeation and migration studies are related to plastics. The simplest interaction to describe physically and mathematically is steady state permeation. The same material constants required for describing this interaction are also used for the description of non-steady state permeation and migration processes. Given the numerous different substances found in packaging and products and the resulting large number of possible combinations of packaging materials with products, not all the necessary material constants required have been experimentally determined. This leads to the use of estimation methods for substance material constants based on their chemical structures. In addition to the simple estimation methods for
240
Piringer
material constants of gases contained in this Chapter, Chapters 4, 5 and 6 deal with the estimation of constants for organic compounds.
9.1 Permeation of gases The study of the permeation of gases is the simplest case both theoretically and experimentally and is therefore treated first.
9.1.1 Permeability, diffusion and solubility coefficients Thomas Graham described his observations of the permeation of carbon dioxide through a polymeric membrane in 1826. Following this, he postulated in 1866 the correct description of the permeation phenomena as a solution of gases in the membrane followed by their diffusion through the membrane. The steady state permeation of gases through a membrane, film or plate having thickness d is calculated with the help of the following simple equation:
Where the flux J is the flow of gas. The flux is the amount of material transported per unit time through a unit surface area and according to Eq. (9-1) is proportional to the constant partial pressure difference Ap between both sides of the membrane. The proportionality constant P is called the permeability coefficient and is the product of the diffusion coefficient D and the solubility coefficient S (or sorption constant) of the gas in the membrane:
P = D . S
(9-2)
S is the ratio of the concentration c of the gas in the polymer and the partial pressure p of the gas in the gas phase in equilibrium with the membrane: (9-3)
S = CP
This ratio is constant for normal gases (Henry’s law) at the pressures found in packaging applications. Under these conditions, the gases are only sparingly soluble in the packaging materials and thus any structural changes in the polymer (e.g. swelling) can be ignored. For this same reason D is practically independent of the concentration c for gases. The differing permeability of a given gas through various materials is expressed in terms of the gas and material specific parameter P. Its dimension results from Eq. (9-1): a) b)
P
=
amount x material thickness surface area x time x pressure difference
: cm3 ~STP)cm cm s Pa
(9-4)
Permeation ofgnses, water vapor nnd volatile organic conipoimris
c) d)
D:
241
$
: cm3(STP) cm3 Pa
The amount of permeated substance can be expressed in mass, mole or volume units. For gases, volume is preferred, expressed as the amount permeating under conditions of standard temperature and pressure (STP), which corresponds to the standard temperature of 273.15 K and standard pressure of 1.01325 .1@Pa. The corresponding dimensions for D and S are obtained at the same time from Eq. (9-4). The standard ambient temperature and pressure (SATP) are set at po = 1 bar = 105 Pa = 0.9678 atm and T = 298.15 K. The data in handbooks however is still mostly expressed with p = 1 atm as standard pressure. For practical purposes the difference between these two conventions is insignificant compared to the variability of the materials themselves. The value for P is presented in various dimensions in the literature. One can convert from various dimensions to the desired ones with the help of the conversion factors listed in Table 9-1. Table 9-1: Conversion factors for several units of the permeability coefficient
[in'] [mil] [100in2][day] [atm]
1
7.5 ' 104
6.57 10"'
10-1
7.5 ' 10-5
6.57. 10"
1.32 . lo-'
9.87. 10"
8.64. 10'
3.87. 1 0 - 1 ~
2.90.10-~~
2.54. lo-'
9.82 . lo-''
7.37 ' 10-15
6.45 . 10-I
1.52 ' 10-11
1.14.
1.54 10-"
1.16. lo-''
1.33 . 103
1
1
I .01 8.75. 10"
Table 9-2 contains values of P for oxygen, nitrogen, carbon dioxide, and water vapor in some polymers (Brandrup and Immergut, 1989). The values of P cover a range of several orders of magnitude between the highly permeable silicone elastomers and the extremely impermeable EVOH materials. As an example, for O2 at 0 "C P = 3.7E-11 cm*s-'Pa-' in polydimethylsiloxane and P = 7.4E-18 cm2s-'Pa-' in EVOH at 40 YOrelative humidity(rh).
242
Piringer
Table 9-2: Permeability coefficients P (cm'(STP)cm cm-2s8Pa-') of gases and water in polymers. Polymer
Permeant
T "C
0 2
25
C02
25
P
1. POLYOLEFINS
Polyethylene density 0.922g . cm-'.LDPE
density 0.9548 cm-'.HDPE
Nz
25
H2O
25
0 2
25 25 25 25
5.18 21 1.58
93 0.825 3.225 0.248 13.5
Polypropylene density 0.907g.
30
0.33
crystallinity 50 %
30
1.7
Poly-4-methylpentene- 1
30
6.9
30
51.0
25
5.67
25
24.23
25
69.45
2. POLYSTYRENE Polystyrene
25 25
biaxially oriented
1.9 1350
25
2.0
25
0.59
25 25
7.9 840
stretched stretch ratio
1.0
25
6.0
1.8
25
4.35 2.18
3.1
25
4.4
25
1.13
5.0
25
0.75
25
0.075
3. POLYMETHACRYLATES
Polymethylmethacrylate
0 2
34
HzO
23
0.116
480
243
Pernzention ofgnsrs, w(itcr v n p r nnd volatile orgrrnic cotnpoiinds Table 9-2: Continued Polymer
Perineant
T “C
p . lo’.;
4. POLYNITRILS
Pol yacrylonitrilc
0 2
2s
0.000 15
CO,
25
0.00060
HzO
25
X6/14
0 2
25
HZO
25
66/34
0 2
25
0.036
CO:
2s
0.16
230
Poly(acrylonitrile-co-styrene) 0.0032 640
HzO
25
0 2
25
0.14
C02
25
0.27
H2O
25
0 2
25
0.35
COZ
25
1.0
HLO
25
1Y00
Polyvinyl acetate
0 2
10
0.
Polyvinyl alcohol
Nz(O %rh)
14
0.0001
N>(100 Yo)
14
0.248
OZ(0 Yo)
25
0.00665
CO2(0 % )
25
COZ(100% )
25
OL(O%rh)
30
0.0000248
02(20 % )
30
0.0000335
Oz(40 Yo)
30
0,0000743
O2(60 %)
30
0.000298
02(80%)
30
0.00187
O?(100 Yo)
30
0.0181
Polyvinyl chloride
NZ
2s
0.0089
(non-plasticized)
0 2
25
0.034
CO2
25
H2O
2s
57143
39161
1500
1800
5. VINYLPOLYMERS
0.00924 65.0
Vinyl alcohol-ethylene-copolymer EVOH
Polyvinylidene chloride
0.12 206 0.000706
NZ
30
0 2
30
0.0003x3
COZ
30
0.0218
HzO
25
7.0
244
Piringer
Table 9-2 Continued Polymer
Permeant
T T
P ' 10"
Poly(viny1idene-co-vinylchloride) 88/12 plasticized with acetyltributylcitrate (YO)
0.5
H20
30
1.38
2.7 4.9
H2O H2O
30
3.07
30
4.77
1.2
H20
30
7.38
N2
25
1.0
0 2
25
3.2
co2
25
7.5
6. FLUOR POLYMERS
Poiytetrafluorethylene
7. POLYDIENES
Poly(butadiene-co-acrylonitrile) 80/20 (Perbunan 18)
73/27 (Perbunan)
68/32 (Hycar OR 25)
25
1.89
25
6.15
25
47.6
25
0.8
25 25 25 25
2.9
25 25
61/39 (Hycar OR 15)
23.2 0.454 1.76 13.9 0.177
25
0.721
25
5.59
Poly(butadiene-co-styrene) N2
24
3.83
80/20(Hycar 2001)
N2
24
1.28
Polyisoprene. Amorph
0 2
25
(natural rubber)
coz
25
92/8(Ameripol 1502)
17.6 115
8. POLYOXIDES Polyoxymethylene
25 25
1.35 683
245
Permeation ofgmes, writer vapor and volatile organic compounds Table 9-2: Continued Pdymer
Permeant
T "C
P.
In"
9. POLYESTERS Poly(oxybutyleneoxyterephthaloyl) PBT
coz
25
0.217
PET
25
0.0108
amorph
25
0.0444
25
0.227
25
0.005 13
25
0.0257
25
0.118
Poly(oxyethyleneoxyterephthaloyl)
crystallinity 40 %
10. POLYSILOXANES Polydimethylsiloxane
0
170
0
367
25
2430
35
32300
11. POLYAMIDES Poly(iminoadipoy1iminohexamethylene) (Nylon 66) 02(40%rh)
30
0.013
02(60 %)
30 30
0.017 0.026 0.052 0.071 0.007 13
02(
I00 Yo)
non-stretched
co2
stretched
COZ
25 25
N2
30
Poly(imino-1-oxohexamethylene) (Nylon 6 )
0 2
30
0.0285
02(20%rh)
30
0.02 18
02(60 Yo)
30
0.0305
02( 100 %)
30
0.0435
coz
20
0.066
H20
25
0.139
246
Piringer
Table 9-2: Continued Polvmer
P ' 10'3
Permeant
T"C
Cellulose hydrate
Nz(0 %rh)
25
0.0024
(regenerated)
02(0 Yo)
25
0.0016
C02(0 % )
25
0.00353
HzO N2(43 %)
25 25
0.00507
02(43 %)
25
0.00536
C02(43 Yo)
25
0.00974
N2(76 "A)
25
0.00559
02(76 Yo)
25
0.00665
COz(76 %)
25
0.0539
N2(100%)
25
0.0138
100 %)
25
0.0087
C02(100)
25
0.192
N2
25
0.087
0 2
25
1.46
co2
25
H2O
25
~
~
12. CELLULOSE AND DERIVATES
02(
Cellulose nitrate
1x900
1.59 4720
An useful characteristic of the materials used in practice is the relatively constant relationship between the P values of two gases and their independence from polymer type (Table 9-3). Take for example the P values of various gases with respect to nitrogen. When a value for one gas is known, then values for another can be estimated using the corresponding value from the table. These relative values are also valid to a lesser degree for the D and S values. The values listed in Table 9-3 are averages for various different polymers and are therefore somewhat dependent on those included in the average. As a result they are for orientation purposes only and their accuracy should not be overestimated. A comparison of the ratios of the P values for COz and O2 from a selection of polymers different from those used in Table 9-3 gave an average value of 4.6 with a standard deviation of 1.3 (Hennessy et al., 1966). The corresponding maximum and minimum values were 7.1 and 2.5. From Table 9-3 one obtains a ratio of Pco,/P0, = 24/33 = 6.3. In view of the large variations in material properties of the same polymer type, which are dependent on the manufacturing and treatment processes as well as the different permeation measurement methods, the variation between the two ratios is acceptable. When estimating the maximum package permeability for guaranteeing the minimum shelf life of a food for example, a safety factor is used anyway.
Pernieation ofgases, w u t u vapor rind volrztile organic compoiinds
247
Table 9-3. Relative values of permeability parameters (van Krevelen. 1990) Gas
P
D
S
EP
ED
02
NZ(=l)
1
1
1
1
1
1
CO
1.2
1.1
1.1
1
1
0.95
CH4
3.4
0.7
4.9
(1)
(1)
0.9X
O?
3.8
1.7
2.2
0.X6
0.90
0.83
0.2s
0.62
0.45
0.4s
He
1s
60
H?
22.5
30
C02
24
H2O
1 5
0.70
0.65
0.55
24
0.75
0.75
1.03
-
0.75
0.7s
1.o 0.94
Example 9-1. The value for permeation coefficient ( P ) of COz through a LDPE film was measured to be P = 2 x 10-"cm3 . cm/cm2 - s . Pa at STP conditions and 2.5 "C. a) How large is the estimated value of P for oxygen in cm' . cm/rnz . d . bar at the same temperature? b) How large is the variation range for this estimation of P? a) First, the P value for COz needs to be expressed in the desired units. Using Table 9-1 there are two possibilities: a l . The value is multiplied by 8.75813 to convert from cm3 'cm/cm2 ' s . P a to cm3 . cni/m2 d . atm and then the result divided by 1.01 to transform the units into bur: (2E - 12) 8.7SE13j1.01 = 173 cm3 . cm/mz . d . bar. The difference between the old units of atmosphere (utm) and bar SI-units is pratically negligible since 1 utm = 1.01 bur. a2. The value is multiplied by 3.33E3 and then divided by 1.54E-11 which then gives: 2E - 12 cm3 . cm/cm2 . s . Pa = 173 cm3 . cm/m* . d . bar. From Table 9-3 one gets a value for oxygen of PO, = 173 '3.8124 = 27.3 cm' . cm/m2 . d . bar b) Taking into account the standard deviation from average value of the relationship between the permeation values for C 0 2 and O2 given above, one gets a maximum value for Poz in LDPE at 25 "C of PO, = 173/2.5 = 6Y cm3 . cmlm' . d . bar and Po, = 173/7.1 = 24 cm3 . cm/m' . d . bar as a minimum value. By using the maximum value theworst possible case for oxygen permeation is taken into account. After converting the values for oxygen in Table 9-2 to these units one gets: Po, = 44.9 cm'. cmlm'. d . bar. This value is within the above range. Example 9-2. What is the maximum value for oxygen permeation ( J ) through a 50 pm thick LDPE film at 10°C when the exterior of the film is in contact with air and the maximum estimated value for oxygen permeation at 25 "C from example 1 is used? The permeation is calculated using Eq. (9-1). The maximum value is obtained when one uses Po2 = 69 cm' . cm/m2 d . bar and assumes that the partial pressure of oxygen on the interior of the film is zero. Taking into account the proper units (1 bar z 1 atm), one gets a perrneation based on 1 m2 surface area of film to be: J=P~~69~~=2900cm'/m2d
248
Piringer
The temperature dependence of the P, D and S constants can be represented with the help of an exponential function (Arrhenius Equation): a) b) c) d) e)
P = Po exp (-Ep/RT) D = DOexp (-ED/RT) S = So exp (-A Hs/RT) Po=DoSo EpzE~+hHs
(9-5)
EP and ED are the activation energy of permeation and diffusion and Hs is the molar heat of solution of the gas in the polymer. These parameters are expressed in kJ/mol where R = 8.3145 J/(mol K) and T is the absolute temperature in Kelvin. The ratio of the activation energy EP and ED of two gases are relatively independent of the nature of the polymer. Furthermore, the ratio of ED values corresponds almost exactly to the ratio of the squares of the molecular cross sectional diameters (02)of the two gases (Table 9-3). This knowledge allows the estimation of D, S and P values with help of easily obtainable molecular properties (see Section 9.1.3). If the value of P is known or can be estimated for a gas in a certain material, then the calculation of the gas permeability through that material of a certain thickness can be made using Equation (9-1). In practice the agreement between the calculated and actual permeability of a plastic material is set within limits. Deviations from the calculated permeability for the same material can come from different manufacturing processes that cause changes in the properties of the material’s surface, the orientation of the macromolecules and other effects. The permeability of a material can vary widely at different locations in the package. Different material thickness of the walls, bottoms, edges and seals, different materials for lid and container or the presence of pores or other leaks for example can all cause considerable differences between the calculated and total effective permeability of a package. In practice it must not be forgotten that P values give an order of magnitude estimation for the selection of suitable packaging materials and thus allow a closer calculation of the total package permeability with the help of the flux J: n
n
Q=z Q i = CAi Ji i
(9-6)
I
Q is the sum of the permeabilities for individual packaging materials and wall thickness of different packaging components. Using the corresponding P and d values for every component i, the corresponding flux J is calculated using Equation (9-1) and multiplied by the component’s surface Ai. The partial pressure difference Ap is treated as a constant. The total permeability of a package developed in this way must nevertheless be checked experimentally due to the above mentioned uncertainties (see next Section).
Example 9-3. A 20 cm long HDPE tube with an external diameter of 10 cm and a wall thickness of 1 mm is filled with an oxygen absorbing substance. Both ends of the pipe are sealed with a 100 p n thick LDPE film and the tuhc is stored in air. What is the total oxygen pernieation into this tube using the permeability coefficicnt values from Table 9-2 for HDPE and LDPE at 25 "C? The total permeation of this pipe can be calculatcd using Eq. (9-6) along with Eq. (9.1). The permeability through the surface area of the HDPE tube is: First convert the value in Table 9-2 to the dcsired units: cm7 cm
1 3 z (8.75E13 conversion factor). 7.219E 4? ( ) ( Then calculate the total amount of oxygen permeating through the walls of the tube:
P = 0.825E
-
.
~
ioonn cm2 m2
=
-
em' cm
cni- day alni
AP
QHopE= A ; .Ji = Ai . P - - = ( n . 10 cm . 2 0 cm) . d
0.95cm7/day Similarly one gets QLDPE = 14.4cm3/day for both LDPE end caps. Adding the oxygen permeation for the tube and the ends together one gets a total oxygen permeation of Q = 15.3 cm'/day. The magnitude of this amount of oxygen permeation is largely determined by the LDPE end caps.
Example 9-4. What permeability is obtained in Example 3 when a 10 pm thick PVDC film is used instead of LDPE for sealing the ends of the tube? What is the ratio of a) the permeation from the PVDC film from the ends to the permeation from the surface of the HDPE tube and the permeation from the LDPE film from the ends in Example 3 to the permeation from the surface area of the HDPE tube? When the ends of the HDPE tube are sealed with 10 pm PVDC film one gets the permeation, using permeability coefficient value for oxygen through PVDC at 30°C given in Table 9-2, in the following way: First, convert the units of the permeability coefficient to the desired units: em' cm
0.000383E - 13-cm* s Pa . (8.75E13 conversion factor) . em3 cm
3.351E - 7- cm2 day atm Then, calculate the permeation through the two end caps:
0.011 cm'/day Note that using a permeability coefficient at a higher temperature (30 "C) will tend to give an overestimation of the permeation at 25 "C. Finally, sum the permeation through the end caps together with the permeation through the wall of the tube: n Qsy,lcm
=
Q, =QPVDC
+ QHDPE
= 0.011
cm3/day
+
0.95 &/day
= 0.96
cm3,/day
I
a). Ratio of the permeation through the PVDC end caps to the permeation through the HDPE tube is: = (0.011 &/day ) / (0.95 cm'/day) < 0.012 b). The ratio of the permeation through the LDPE end caps to the permeation through the HDPE tube is: QPVDC/QHDPE
QLDPE/QHDPE
=
(14.4 cm3/day
) / (0.95 cm'/day)
=
15.1
250
Piringer
9.1.2 Experimental measurement of gas permeability The measurement of sorption, diffusion and permeability coefficients takes place as a rule using one of three methods: sorption of the gases in the polymer, permeation through a membrane (film or sheet) into a sealed container or permeation through a membrane into a gas stream. As far as possible sorption methods should be used together with permeation methods that are specific for the measured gas/polymer system in order to uncover any possible anomalies or errors in the measurements by comparison of results. I. Sorption: The method allows a direct measurement of S from the equilibrium between gas and polymer. The volume of gas taken up by the polymer can be measured gravimetrically, manometrically or using a gas specific detector. Headspace gas chromatography is an useful technique for this. The S values then come from:
Where me is the amount of gas absorbed in the volume V of the polymer at equilibrium and pc is the corresponding partial pressure of the gas being studied. In order to check if S stays constant, one measures the me value for several pressures pe at the same temperature. S comes then from the slope of the straight line me = f(p,). Deviations from linearity of the line means deviations from Henry’s law. 2. Permeation in a sealed container: The amount of gas m, found in the container’s chamber as a result of permeation through the film is plotted as a function of time t (Fig. 9-1).The partial pressure p1 of the gas permeating into the film is held constant. Normally the chamber volume is so large that even upon reaching steady state permeation the partial pressure p2of the permeated gas remains negligibly small (p2 << PI). A simple method is to measure the increase in pressure (p2) over time in an initially evacuated chamber. Another possibility is the use of sorbents in the chamber so that the partial pressure (p2) is kept practically at zero. The amount of permeating gas can be gravimetrically determined with the help of the sorbent. It is also possible to use
0
e t -
Figure 9-1: Time dependence of permeation.
Pernieririoti ofgases. it~i[i>r v ( i p o r nnd volatile organic c o n z p n i ~ n ~ ~ s
251
specific gas detectors. Gas chromatography (GC) in combination with a thermal conductivity detector (TCD) is particularly well suited. For the measurement of oxygen permeability a coulornetric method or for carbon dioxide an infrared detector is used. A frequently used item of equipment for measuring gas permeability is composed of a two-piece metal cell. The test gas flows through the upper half while at the same time the amount of gas permeating through the film is measured in the lower half. The amount permeating is measured using a mercury column at constant pressure. The method is applicable to a permeation range of 3-20,000 cm'/(m2 day bar). A corresponding international test method is IS0 2S56. One obtains the permeability coefficient with the help of Eq. (9-1) using the slope of the asymptote in Fig. 9-1 which means steady state permeation has been reached: ~
where pl, d and the film surface area A are known. The intersection of the asymptote with the time x-axis, 0,allows the diffusion coefficient to be calculated (time lag method, see Chapter 7):
The sorption coefficient is then calculated from S = P/D. 3. Permeation in a gas sfreurn. The film being investigated separates a cell into two chambers. A stream of gas, e.g. nitrogen at normal pressure, containing the gas being studied, e.g. oxygen or carbon dioxide with the partial pressure pl, flows through the first chamber. Pure nitrogen flows through the second chamber with a known flow rate f cm3/s (STP) and subsequently into a O2 or C 0 2 detector. After reaching steady state permeation the value of the partial pressure in the second chamber p2 is reached. With help of Eq. (9-1) one then gets:
(9-10) where c2 is the concentration of the test gas in the second chamber expressed as the dimensionless ratio of p2 to the total pressure p in this chamber. If the permeability of a tube is studied instead of a film, the permeability coefficient can be calculated using its length L and its outer r I and inner r2 radii:
(9-1 1) Here, pure carrier gas flows through the inside of the tube (chamber 2) while the outside of the tube is surrounded by the partial pressure of the test gas p1. For materials having extremely low permeabilities one can direct the gas stream from the second chamber through a tube containing sorbent which traps the test gas. The amount sorbed during a given time interval (in steady state) can be determined analytically. This method is also recommended when one has several concurrent test runs and does not have a detector connected directly to every cell. The most common sources of error for permeation measurements are leaks in the film between the two test chambers. Measurements at two or more different pressures in the first chamber can help detect leaks. If for example the permeation rate
252
Piringer
increases proportionally to the total pressure difference between the two chambers and not just to the partial pressure difference of the test gas, then there must be leaks present. These leaks can possibly be in the form of micro pores in the film. When measuring permeation into a gas stream the tests should be repeated at several different gas flow rates to detect possible influences of mass transport in the gas phase. Such influences are negligible if the values for P remain constant below a certain gas flow rate. ~
~
-
Example 9-5. When measuring the gas permeation through a film one obtains a time-axis intercept of the steady-state pcrmeation asymptote of 0 = 254 min using the time-lag method. The thickness of the film being studied is 75 pm. The pressure difference (Ap) between the two sides of the film remains constant at 0.2 bar and the flux through the film is 2 cm”/m’ h. Calculate the value of the solubility coefficient S. Using Eq. (9-9) one can calculate the diffusion coefficient using the lag time 0: d2
(0.0075 cm)’
6.0
6.254 iiiiii (60s/niio)
D=-=
= 6.15E - 10 cm2/s
From Eq. (9-1) one can calculate the permeability coefficient, P:
Finally by using the values for P and D in Eq. (9-2) one can calculate the solubility coefficient S: = p = 2 08E-9 cm3 crn/cmz D h.15E-lll c m l / s
5
bar
= 3.4 cm’(STP)/cm’ bar
Example 9-6. A constant 0.5 ml/min stream of nitrogen flows through a 1 m long hose having an outer diameter of 3 cm and 5 mm wall thickness. The hose is in contact with air. After steady state permeation is reached the oxygen concentration in the nitrogen is 0.8 ppm (v/v). What is the permeability coefficient P o f this hose? Using Eq. (9.11) one can calculate the permeability coefficient as follows:
= 2.05E - 11 cm3 cm/cm2 s atm = 2E
-
16 cm3 cm/cm2 s Pa
z 0.018 cm3 cm/m2 day bar
Total permeation measurement
The total permeability, Q = J A, of a C 0 2 containing package can be measured where the package, e.g. a bottle containing carbonated mineral water with volume VR is placed in a sealed container having volume VC with a C02 free atmosphere. The amount of CO;?permeating out of the package at time t is determined by the concentration cc of the carbon dioxide found in the container at this time. Using relatively small measurement intervals, one can observe a linear increase in cc which allows one to calculate Q: (9-12)
Using the known Q (e.g. expressed in volume at STP) allows calculation of the amount of COz t h e package will lose, Vloss(also at STP), by the end of its shelf-life time t:
Perrnecrtion of gnses, wwter vnpor r i t i d volntile organic cornpoiinds
253 (9-13)
Where VL is the volume of the filled product, SL is the solubility of C 0 2 in the product and po is the initial C 0 2 pressure in the package. The solubility of C02 in water at 20 "C is SL= 0.84 cm3 (STP) /cm3 bar. The concentration cc can easily be measured using a C 0 2 specific detector. One can for example remove 0.5 ml from the container using a gas-tight syringe and inject it into an air carrier gas that comes in contact with a stream of water. The increase in the electrolytic conductivity in the water caused by the presence of C02 is proportional to the concentration in this range. With help of such an analytical system the C 0 2 concentration can be measured within 30 seconds with a detection limit of 3 ppm (Leibl et al., 1990). With this setup, non-destructive testing of the total package permeability can also be carried out. Using the results obtained for C02, the total permeability for other gases can be estimated with the help of Table 9-3. Example 9-7. Sensory analysis of a COz containing mineral water showed that a loss of 15 YO or more from the initial quantity of COr led to a significant quality decrease in the form of a flat taste. A 1.5 liter plastic bottle has an initial fill pressure of 3.8 bar. A tightly sealed bottle has a total permeability of Q = 6 mg/day at 20°C. How long can this bottle be stored before a noticeable sensory change takes place in the mineral water? To solve this problem one can use Eq. (9.13). From the given value for the solubility of CO2 in water at 20 "C, S L = 0.84 cm3 (STP)/cm3bar one can calculate the initial C 0 2 content of the bottle:
PI).SL.VL = 3.8 bar 0.84cm'(STP)/cm3 bar. 1500cm3 = 4788 cm'(STP) The molar volume of a gas at 0°C and 1 bar 2 1 atm is 22.4 dm'. Given the molar mass of C 0 2 at 44 gimol, the C 0 2 loss can be calculated to be 6 mg/day at 20 "C: rnol
Q = 22.4 (dm3/mol) . 1000( cm3/dm3) .0.006 g/day. - = 3.05 cm3(STP)/day 44 R
The loss of 15 YO of the intial COz means VI,,,, = 718 cm' (STP). With these values one can calculate the time t before too much COr is lost:
3os
' )] :_ :_ t = 255 days
After more than 8 months storage there is a noticeable loss in product quality. Note that this loss in quality is based only on the loss of C 0 2 and not caused by possible sensory changes due to migration of sensory active substances from the bottle.
The influence of pores and leaks in a package on the total permeation depends primarily on whether or not the package is vacuum packed or at atmospheric pressure (Becker, 1965). For the case of vacuum packaging, the Hagen-Poiseuille equation for laminar gas flow can be used as a first approximation: (9-14)
254
Piringer
where Vs is the volume of gas flowing through a pore with radius r and length 1 up until time t and pl and pz are the pressures at each end of the pore, Po is the pressure related to Vs (1 bar) and q is the dynamic viscosity of air. If the inside of the package has the same total pressure as its surroundings but a difference exists in the partial pressures of a certain gas, e.g. oxygen, then the transport of this gas occurs by diffusion according to an equation analogous to Eq. (9-1) and one obtains: Vd=xr2D
Po 1
t
(9-15)
where Vd is the volume of gas diffusing through the pore during the time t, and D is the diffusion coefficient of the gas in air. The remaining parameters are identical to those used in Eq. (9-14). A precondition for the optimization of a package having a specified minimum shelf life date for a food with a known oxygen and/or water sensitivity is the calculation of the permeability of laminate structures. The total permeability Q, of a laminate film made from n different plastic layers with thicknesses di and having permeability coefficients of Pi can be calculated using the following formula: (9-16) Here the magnitude of Q, is determined by the layer having the largest ratio of di to Pi. A is the surface area of the laminate and Ap is the partial pressure difference between the two sides of the laminate. A manifold variety of packaging exists on the market as a result of the many possible combinations of packaging materials with different properties. ~
~_____
Example 9-8. A pouch is made from 5 dm2 of a heat sealable laminate film material. The film has the following structure: 25 pm PP, 5 pm EVOH and 50 pm LDPE. How much oxygen permeates into this pouch at room temperature'? The total permeation of the pouch is calculated using Eq. (9-16). Using the permeability coefficient values for the different materials from Table 9-2 one gets:
0.W2.5 cm
S00cmZ.0.21bar.I 1 .Ill E+SPa/bar 1
Qv
20164E+14 ~
10M)SE+7
=
0.lX)oS cm
1.7E- 13 cm3cm/crn2sPa + O.~XM024XE-13
+-)
0 00SOcm 5. IXE- 13
=
1.9013E + 7s/cm3
:_ Qv = 5.259E - 8 cm3/s.8.64E + 4 s/day
=
0.00454 cm'(STP)/day
Making the assumption that room temperature is below 30 "Cthis would be a maximum value for the permeability.
9.1.3 Estimation of gas permeability Given the relationship, P = D . S, the permeability can be calculated from knowledge of the solubility of the gas in polymer and its diffusion coefficient.
Permeation o,fgasrs, w i i t i v vapor atid voInriIe organic cornpoiitiris
255
The soliihility coefficient Due to the very low solubility of normal gases in polymers the S values for various polymers do not differ very strongly from one another. The sorption coefficient S (298) at 25°C can be estimated quite well in an amorphous polymer in its rubbery state with help from the following formula (van Krevelen, 1990): logS(298) = -7.0
+
0.01
(9-17)
f0.25
where E is the potential energy constant of the permeating gas and k is the Boltzmann constant. The ratio Elk is described as the Lennard-Jones temperature (Table 9-4). S is expressed in cm3 / (cm3 Pa). Ihblc 9-4. Diameters of simple molecules. Molccule
(5
E/k
(gas)
(nm)
He
25.5
(K) 10.2
HZO
809 60
H2
26.4 28.3
Ne
28.2
33
N €-i7
29.0
558
0 2
34.7
107
Ar
35.4
93
CH10H
36.3
4x2
Kr
36.6
179
co
36.9
92
CH,
37.6
149
N2
38.0
71
c'oz
39.4
19.5
Xc
40.5
23 I
SO2
41.1
335
CIH4
41.6 41.8
22s
CH.qCl C2Hh
44.4
216
-
CHzClz
49.0
356
C.&
51.2
237
ChHh
53.5
412
The heat of solution (molar enthalpy of sorption) of small molecules in elastomers is positive (endothermic effect) while it becomes negative for larger molecules (exothermic effect). The heat of solution becomes exothermic as soon as the sorption energy evolved becomes larger than the energy needed for the formation of a free volume large enough to accept the size of the gas molecule in the polymer. From the S value at 25 "C the heat of solution AHs and So in a polymer above its glass transition temperature T, can be estimated using:
256
Piringer
3 .lo-3 R logso
=
1.0
= -5.5
-
0.01
-
;
0.5
(9-18)
f 0.8
0.005
For amorphous polymers in their glassy states, the following expressions analogous to Eqs. (9-17) and (9-18) are used:
+ 0.01
logS(298) = -7.4 3R. 1 0 - 3
0.5
=
logso = -6.5
-
0.01
-
i0.6
;+ 1.2
(9-19)
i1.8
0.005
Using these expressions the solubility of a gas at a given temperature, S(T), in an amorphous polymer can be estimated: logS(T) = logso
0.435
-
& = logS(298) AH
- 0.435 3 R ($
-
1 298 )
(9-20)
If the degree of crystallinity in the polymer is designated with x, and S, is designated as the solubility of the gas at 25 "C in the amorphous polymer, then Eq. (9-21a) can be used for an approximation of the solubility in a semi-crystalline polymer: Ssc(298) = Sa(298) (1 Dsc
= Da
(1
(9-21a)
- xC)
(9-21b)
- XC)
The diffusion coefficient If one selects the nitrogen molecule as a reference molecule then one can set up the following relationship between the activation energy of diffusion, ED, of a gas i, its molecular diameter oi and the glass temperature T, of the polymer (van Krevelen, 1990): 10-3
R
=( *)2
[7.5
-
2.5.10-4 (298 - T, ) 2
ON2
1
50.6
(9-22a)
for elastomer (T, < 298 K) and 10-3
!?R =
R
( 2 [7.5 ~) - ~ 2.5. lop4 (Tg- 298)3/2 f 1.0 ON2
(9-22b)
for amorphous polymers in their glassy states (Tg > 298 K). The values of molecular diameters for simple molecules are given in Table 9-4. There is a linear ralationship between log Do and ED:
2 lop3 2
logDo = lop3
-
IogDo =
-
4.0 f 0 . 4
elastomers
5.0 f 0 . 8
glassy polymers
(9-23)
Permeation r>fgases, wrr~ert q m r arid volatile o r p n i c conipoiimis
257
The diffusion coefficient D(298) in cm2k at 25 "C and D(T) at temperature T for a given polymer can be estimated with help from the following expression: logD(298)
logDo
-
!$ = -4.0
1.46.
F.lop3 !$
logD(T) = logDo -
0.46.
-
= logD(298)
!b R
-
0.435
9 (+ A)
(9-24)
-
The influence of crystallinity can be estimated for a first approximated using equation (9-21b) which is analogous to that for S. D, is the diffusion coefficient in the amorphous polymer and x, is the degree of crystallinity. D, is calculated with the help of Eq. (9-24).
The permeability coefficient The estimation of P can be made using the formulae for S and D in following empirical expression (van Krevelen, 1900): for elastomers:
+
logPo = -10.1
1 0 - 3 2 fo.25
logP(298) = -10.1 - 0.46 . lop3
% f0.25
(9-25)
for amorphous glassy polymers: logPo = -11.25
+
lop3
logP(298) = -11.25
-
f0.75
% 5~ 0.25
0.46.
(9-26)
for semi-crystalline polymers:
and for any polymer: logP(T) = logP(298)
E p / R = AHs/R
-
0.435
2 (5
-
I
298)
(9-28)
+ ED/R
Example 9-9. Estimate the average values for the solubility coefficients of oxygen and carbon dioxide in polypropylene (PP) having 50 'YO crystallinity at 30 "C. Use the E/K values for both gases and compare the ratios of carbon dioxide solubility coefficients to the oxygen coefficients (SCO,/SO,) with the ratios of Sco2/SoZusing values from Table 9-3. For the solubility and heat of solution of O2 in PP at 30°C one uses Eq. (9-19) and Table 9-4: ~. AH5
= 1.0 - 0.01 . =
logs,) = -5.5
-
0.005 .
=
1.0 - 0.01 . 107 = -0.07 -5.5
-
0.005 . 107 = -6.035
258
Piringer
Using Eq. (9-20) one calculates a value of S for amorphous PP at 30 "C: logS(303) = logs"
- 0.435
AHs/RT = -6.035
-
0.435 (-70.0) . (L) = -5.9355 303
:. SO,(303) = 1.16E - 6 cm3(STP)/cm3 Pa With a crystallinity of 50 YOone gets using Eq. (9-21a): SsC= S,(303). (1 - xc) = 1.16E - 6 . (1 - 0.5) = 5.8E - 7 cm'(STP)/cm3 Pa = 0.058 cm3(STP)/cm3 bar In the same manner one obtains the solubility for C02: SCO,= 3.87E - 6 cm'(STP)/cm3 Pa = 0.39 cm3(STP)/cm3bar The ratio Sco2/So2is equal to 6.7. The ratio for Sco,/So2using values from Table 9-3 is equal to 2412.2 = 10.9. Example 9-10. Estimate the average value for the diffusion coefficient for oxygen and carbon dioxide in polypropylene with 50 % degree of crystallinity at 30 "C. Use the corresponding molecule diameter (J and the average Tg value of 267 K for PP. Calculate the corresponding permeability coefficient value using the solubility coefficient value determined in Example 9. Using Eq. (9-22) for elastomers and Table 9-3 one gets for oxygen: R
=
)('
(g)2 p.5
2
(298 - Tg)*]=
p.5 - 2.5.
ON2
- 2.5. 10-' . (298 - 267)']
=
6.0536 E
The corresponding value for 10-3 C 0 2 is 7.260. Using Eq. (9-23) for elastomers one can calculate the Do values for 0 2 and COr: D - 4.0 = 6.0535 - 4.0 = 2.0535 for O2 logDo = lo--, ER logDo = 7.260 - 4.0 = 3.260 for C02
Now using Eq. (9-24) calculate the diffusion coefficient for O2 and COz at 30 "C:
IogDo, (303) = logD"
135 -
r . lo-' 5 = 2.0535 R
435
'6.0536 = -6.6373,
:. Do, (303) = 2.3E - 7 cm2/s 435
logDc0, (303) = IogD" - -.T
:. Dco,(303) =0.6YE
-7
435
1 V 3 5 = 3.260 - -. 7.260 = -7.1628. R
303
cm2/s
Correcting for the 50 % degree of crystallinity using Eq. (9-21b) leads to the final estimated diffusion coefficient values: Dsc = D, . (1 - x,) = 2.3E - 7 . (1 - 0.5) = 1.15E - 7 cm2/s for 0 2 Dsc = D, . (1 - x,) = 0.69E - 7 . (1 - 0.5) = 0.35E - 7 cm2/s for C02 With the corresponding S value from Example 8 one can calculate P using the product of S and D: Cm2 cmlcm C~~(STPJ PsC(303) = Ssc(303). Da(303) = 5.8E - 7 x . 1.15E - 7- = 0.67E - 13-cm? s pa for 0 2 PsC(303) = Ssc(303) . Dsc(303)= 3.87E - 6
cmZ(STPl
x
7
cm-
. 0.3SE - 7-
=
Cm3CIIl
1.3E - 1 3 a for C 0 2
Pernienrion uf gases, w i t e r vnpor nnd volatile organic cornportnds
259
Example 9-11. Estimate the average value of the diffusion coefficient for water in polyamide 66 (PA or nylon) with a degree of crystallinity of 70 % and water content of 3.6 % at 25 "C. Compare this value with one at 0 % water content. At 0 YO relative humidity for water in PA 66 at 25 "C and using the T, value of 60°C from Table 2-2, one can calculate the value for 10-'ED/R using Eq. (9-22b) for a polymer in a glassy state and Table 9-4: 7.5 - 2.5E - 4(T, 264 (%)
k.5
- 2.5E - 4(333 - 298)'"]
-
298)'"]
=
= 3.59
For hydrophilic polymers Eq. (9-30) is valid and consequently: 3 ED - 7.0 = 3.59 - 7.0 = -3.405 IogDo = lo-Using Eq. (9-24) one calculates a diffusion coefficient for the amorphous state to be: logD(298) = IogDo - 1.46. lo-' D(298) = 2.3E 9 cm2/s
5 = -3.405 R
-
I .46 .3.59 = -8.646
-
Correcting the diffusion coefficient for the degree of crystallinity (Eq. 9-21) one gets: Dsc = D,(l - x,) = 2.3E - 9(l - 0.7) = 6.8E - 10 cm2/s Eq. (9-31) is used to correct for a water content of 3.6 %: logD = logDw,o + 0 . 0 8 ~ = log(6.8E - 10) + 0.08(3.6) = -8.879 .' .
D.16 (298) = 1.3E 0 " ,
9 cm2/s
~
Example 9-12. Estimate the average value for S. D and P of oxygen and water in polystyrene (PS) at 25 "C. The average value of T, = 90 "C for PS is used from Table 2-2. Using Table 9-4 and Eq. (9-19) for glassy polymers one can immediately calculate the solubility coefficients: logSoz(298) = -7.4 + 0.01 = -7.4 + 0.01 107 = -6.33. So, = 4.7E 7 cm3(STP)/cm3Pa K E l o g S ~ ~ o ( 2 9= 8 )-7.4 + 0.01 ;= -7.4 + 0.01 .460 = -2.8, Soz = 1.6E - 3 cm3(STP)/cm3Pa -
The values for the 1 0 - 3 E ~ / Rvalue for an amorphous polymer in the glassy state are calculated using Eq. (9-22b): k . 5 - 2.5E - 4(T, 1 0 - j E ~ / R= cA)2
-
298)'"]
=
ON2
(h)
747 2
c%)'[
p.5 - 2.5E - 4(363 - 298)"2] = 6.14
iO-;E,,/R
=
(:)'[7.5
-
7 5 - 2.5E
- 4(T, -
298)
"'1
=
2.5E - 4(363 - 298)3!2] = 3 56
Eq. (9-23) for Do in the glassy state and Eq. (9-24) for D(298) one gets: for
0 2 :
for H 2 0
logDo = :
E
A - 5.0 = 6.14 - 5.0 = 1.14
IogDo = IO-'
5 - 5.0 = 3.56 K
-
5.0 = - 1.44
260
I
Piringer
logDo,(298) = IogDo - 1.46.
E
= 1.14-
1.46.6.14 = -7.8244.
Do, (298) = 1.5E - 8 cm2/s lOgD~,o(298)= bgD" - 1.46.
ED
=
-1.44 - 1.46 3.56 = -6.6376,
DHlo(298) = 2.3E - 7 cmZ/s By combining the above solubility coefficient value with the diffusion coefficient the permeability coefficient can be calculated using Eq. (9-2): P0,(298) = D . S = 1.5E - 8 cm2/s . 4.7E - 7 cm3(STP)/cm3Pa = 7.044E - 15 cm3cm/cm2sPa P~,0(298)= D . S = 2.3E - 7 cm2/s . 1.6E - 3 cm3(STP)/cm3Pa= 3.68E - 10 cm'cm/cm*sPa These calculated values are comparable to the experimental values given in Table 9-2 for permeation of oxygen and water through PS.
9.2 Permeation of water vapor Experimentally measured data for water vapor permeation are given in Table 9-2. One recognizes immediately the large differences in water permeability compared to the permanent gases, particularly for polar polymers. The cause of these large differences is the high polarity of the small water molecules and their tendency to form hydrogen bonds. Such H bonds exist between the water molecules themselves as well as between them and polar polymer groups. Each of the polar OH groups in hydrophilic polymers like cellulose undergoes strong interactions with a water molecule, whereby the fraction adsorbed on the polymer surface can have the same order of magnitude as the amount of water dissolved in the polymer according to Henry's law. The water sorption isotherms have different forms depending on the structure of the corresponding polymer. Other factors also play a role in the tendency of polymers to sorb water, like the access of the H20 molecule to the polar groups and the degree of polymer crystallinity. These factors make the correlation between structure and sorption much more difficult. The effect of various polar groups is dependent on the degree of moisture present. From the evaluation of empirical data collected the estimation of water content per polymer structural unit can be made at 25 "C using molar ratios at different relative humidities (Table 9-5). With these values one can calculate the solubility constant (sorption coefficient) in cm3 (STP)/cm3polymer by multiplying them with 22.4E3/Vmwhen the molar volume of the polymer structural unit, V,, (cm3/mol)is used. The molar heat of solubility for water is around 25 k.J/mol for nonpolar polymers and 40 kJ/mol for polar polymers. The diffusion coefficient for water is also strongly dependent on interaction with the polymer. Polymers with many H bonds forming groups increase the D value as one of the consequences of the beginning of swelling. A good approximation is: logD
= logDw,o
+0 . 0 8 ~
(9-29)
where w is designated as the percent water content in the polymer. In hydrophilic polymers the diffusivity of water is greatly reduced due to strong interactions. A good approximation for this case is (van Krevelen, 1990):
261
Permeation of gases, water vapor and volatile organic compounds
logD0 =
%
-
7.0
(9-30)
with E D in J/mol. For weakly hydrophilic polymers like polyethers and polyrnethacrylates the same relationship between Do and ED is valid like that between the simple gases. With increasing water content the diffusion coefficient in this case also decreases significantly due to the clustering of the water molecules about the polar groups, leading to relatively immobile water molecules. In contrast to Eq. (9-29), here: logD
= logDw,O
-
0.08~
(9-31)
In completely hydrophobic polymers like the polyolefins, as well as some polyesters, the water vapor acts like a simple gas because of its extremely low solubility as well as its diffusivity. The permeation of simple gases in polar polymers is also dependent on relative humidity because of the water's strong interaction with the polymer. Particularly large is the effect of humidity on the oxygen permeability of barrier layers made from EVOH. At 20°C and 100 % relative humidity the permeability is 300 times higher than at 0 % relative humidity at the same temperature. By orientation and thermal treatments the barrier properties at high relative humidity can be significantly improved (up to a factor of 10). Table 9-5: Molar water content of polymers related to structure groups at several relative humidities at 25 "C. ~
~
~
Group
Relative humidity 0.3
-CH3 -CH2 -CH=
(1.5. lo-')
0.5 (2.5.
0.7
0.9
1.0
(3.3 lo-')
(4.5 . lo-')
(5 ' 10-5)
0.001
0.002
0.003
0.004
0.005
0.025
0.055
(0.11)
(0.20)
(0.3)
0.025
0.05
0.075
0.14
0.2
O=
0.006
0.01
0.02
0.06
0.1
-OH
0.35
0.5
0.75
1.5
2
-NH2
0.35
0.5
0.75 2.8
(1.5) 5.3
(2)
-COOH
0.2
0.3
0.6
1.0
1.3
-coo-
1.1
2.1
4.2
0.35
0.5
0.75
1.s
2
-CI
0.003
0.006
0.015
0.06
(0.1)
-CN
0.015
0.02
0.065
0.22
(0.3)
..
=c=o -C
P \O-
-NH3'
//O
-c
\NH
262
Piringer
A gravimetric method is often used for the measurement of water vapor permeability. The water vapor transmission rate (WVTR) according to this method is the amount of water vapor in g that permeates in 24 hours under standard test conditions (temperature, air relative humidity, water vapor sorbant) through a 1 m2 sample surface area. The method measure a flux and not a permeability coefficient. To carry out the measurement a dish is filled with a water vapor sorbant. The dish is covered with the sample film, sealed with wax and stored in a moist environment. The amount of water vapor that penetrates through the film is calculated from the steady state weight increase of the dish over time. Example 9-13. Estimate the water content in Nylon 6.6 at 25 "C at a relative humidity of 0.7. The crystallinity of the polymer is 70 YO(van Krevelen, 1990). The structural repeat unit of Nylon 6.6 is: [-NH(C0) - (CH;!),-(C0)NH - (CHz),-] Looking at Table 9-5 it is obvious that one can ignore the water sorption capacity of the CH2 groups. Consequently, the two (C0)NH groups have a molar water content, at a relative humidity of 0.7, of 2.0.75 = 1.5mol/unit The relative molecular mass of the repeat unit on Nylon 6.6 is 226.3 g h o l so that 1.5 times 18 g water in 226.3 g polymer is equal to 12 g water can be absorbed per 100 g polymer. Taking into account the effect of crystallinity using Eq. (9-21a) one gets for the semi-crystalline polymer: S,, = S,(1 - x,) = 12. (1 - 0.7) = 3.6 g/100 g polymer This value is compared to an experimental value of 4 YO for water sorption in Nylon 6.6 at a relative humidity of 0.7.
9.3 Permeation of organic vapors Unlike the slightly soluble simple gases, the solubility of organic compounds in polymers plays an important role. Their solubility determines the distribution of a substance between the polymer and its environment; and consequently the degree of interaction and the resulting property changes. Not all packaging materials are suitable for all applications, due to the good solubility of water, fat and other macro components of a filled product in them. Additionally the good solubility of organic compounds in plastics can under certain conditions lead to a reduction in the product's quality, due to the sorption of aromas, flavors and other food components in the packaging material.
9.3.1 Dependence of permeability coefficient on concentration For a first approximation, the simple expressions in Eqs. (9-1), (9-2) and (9-5) can be used for calculating the permeation of a given organic substance. However, the applicability is to some degree considerably reduced, depending on the molecular structures and their related properties. Various deviations from the behavior of simple gases complicate the calculated estimation of an organic substance's permeability. For the same reasons, the published data for S, D and P values can be plagued to some degree by serious measurement errors. In view of the ranges of the three param-
Permeation of gases, ww[t'r vapor and volatile organic cornpounds
263
eters, potentially extending over several orders of magnitude, it is nevertheless unavoidable to use these data for estimating permeability. Table 9-6 gives the permeability coefficients for a series of organic compounds in LDPE at various temperatures (Salame, 1961). A collection of diffusion coefficient values for organic substances in polyolefins are given in Appendix I. Table 9-6: Permeability coefficients P (g mm m-*d-' bar-') of organic compounds in LDPE (Salame. 1961). Compound Acetaldehyde
0°C 1.34
Acetanilide
21.1 "C
54.4 "C
0.008
0.16
Acetic acid
0.14
1.22
25.9
Acetic acid anhydride
0.051
0.32
11.6
Acetone
0.5s
2.67
72.3
Allylalcohol
0.063
0.57
Aniylacetate
0.22
3.42
i- Amylalcohol
3.9
n-Amylpropionate
11.8
Benzaldehyde Benzene
0.098 0.15 17.7
0.67 2.67 173
Benzoic acid
0.028
Benzylalcohol
0.16
n-Butylacetate n-Butylalcohol
9.04 106
23.4 81.0 1770
119 83.7 295 54.2 430
116 417 5400
2.24
14.2
8.02
59
5.9 0.04
0.18
sek-Butylalcohol
0.05
0.24
14.8
t-Butylalcohol
0.02
0.10
10.6
But yraldehyde
0.35
3.93
n-Butyric acid
0.075
1.89
39.3
0.12
8.5
Camphor Carbontetrachloride
1.34
0.078
i- Amylpropionate
Aniline
73.9 "C
2.36
20
240
Chloroacetic acid
0.12
m-Chloraniline
0.63
229
3080 5.0
109 92.8 393 228 63.7 17700 23.6
Chlorobenzene
22.7
179
1730
8300
p-Chlorotoluene
11.8
110
1640
7300
Cyclohexane
12.4
98.7
1470
5900
3.7
28.0
480
1620
5x2
1230
Dekane 1.2-Dibromoethane Dibutylether Dibutvbhthalate
55.0 4.4
33.6
5.7
10.9
264
Piringer
Table 9-6: Continued Comvound
0 "C
o-Dichlorobenzene
21.1 "C
54.4 "C
73.9 "C
3140
11800
60.9
Diethylenegl ycol Diethylether
0.30 18.9
Diethyloxalate
123 0.28
Dipentene
5.9
50.3
798
3190
Ethylacetate
0.75
6.5
149
669
Ethylalcohol
0.28
Ethylenglykol
0.50
Ethyleneglycolmonobutylether
0.26
Ethylformiate
5.9
Ethylmercaptane
10.2
157
E th ylpropionate
9.8
Formaldehyde
0.21
Formamide Formic acid
0.26
15700
4.7
20.0
0.09
Glycerine
0.14 19.1
n-Heptene
106
0.63
1040
3200
3540
11800
106
n-Heptylacetate
7.1
Heptylalcohol
0.39
n-Hexane
3931
70.8
0.20 0.10
Furfurylalcohol n-Heptane
13.8
18.9
138
Hydrochinone
0.02
Methylacetate
0.14
5.5
Methylalcohol
0.1
Methylethylketone
1.45
Methylcyclohexane
0.48 4.95
10.9 128
39.3 550
108
Nitrobenzene
0.15
1.93
39.3
165
Nitroethane
0.37
1.06
25.1
113
Nitromethane
0.83
Octadekane
0.71
Octylalcohol
0.039
0.20
Oxalic acid
10.1 0.08
73.9 0.09
i-Pentane
18.9
106
1970
7860
n-Pentane
38.1
206
5900
23600
Phenol
0.04
0.2
9.4
47.1
n-Propylalcohol
0.03
0.2
8.8
66.0
i-Propylamine
0.90
16.0
275
1260
Perrnecition of gases, writer vapor and volatile organic conipoitnds
265
Table 9-6:Continued Compound Tetradecane
0°C
0.67
Tetradecene Toluene
p-Xylene
5.7 4.7
22.7
1YY
14.2 33.7
101 191
1.1.l-Trichloroethane o-Xylene
21.1"C
54.4"C
73.9"C
159
393
2270
11300
1420 1890
6530 6410
I02
Some measured values, D and K, (Koszinowski 1986, and Koszinowski and Piringer, 1990) are contained in Table 9-7. These data deal mainly with the partition coefficients of hydrocarbons, alcohols, phenols and a series of aromas between polyolefins and a liquid phase (ethanol, methanol) as well as diffusion coefficients of these substances in the polymer. Table 9-7:Diffusion coefficients of organic compounds in LDPE and partition coefficients between LDPE und methanol or ethanol(*) at 23 "C. Compound
Molecular formula
Hydrocarbons Decane Dodecane Tetradecane Hexadecane Octadecane Eicosane Diphenylmethane Limonene a-Pinene P-Pinene p-Cymene Myrcene
K
D . 10"'
calc.
exp.
[cm2/s]
0.50 0.79
0.55*
-
0.97* 1.3* 1.6* 2.5* 4.2* 0.25* 0.42 0.64 0.63 0.34 0.36
34
1.3 1.8 3.1 4.9 0.22 0.24 0.33 0.33 0.19 0.33
0.0040 0.012 0.020 0.031 0.049 0.0028 0.017
0.0047* 0.021* 0.029* 0.033* 0.053* 0.0023 0.014
55
18
14 10 8.3 48 43 14 14 54 70
Alcohols
Heptanol Dodecanol Tetradecanol Hexadecanol Octadecanol Diethylene glycol-monoethylether Borneo1 (1.7.7-trimethyl-bicyclo-2,2,1-heptane-2-ol)C I , , H I ~ 0 3
11
8.2 6.4 4.8 38 4.8
266
Piringer
Table 9-7: Continued Compound
Molecular formula
K
D . 10''
calc.
exp.
Dimethylbenzylcarbinol
0.0095
0.012
7.5
3,7-Dimethyloctanol
0.0078
0.0085
9.2
Dimethylphenyleth ylcarbinol CllH160 Geraniol (2-trans-3,7-dirnethyI-2.6-octadiene-8-ol) CloHlxO
0.012
0.013
0.0053
0.0066
15
Hexenol (cis-3-Hexene-1-01)
Cdi@
0.0022
0.0024
14
Linalool(3.7-dimethyl-l,6-octa-diene-3-ol)
CIOHIRO
0.012
0.0086
19
Menthol (2-Isopropyl-5-methyl-cyclohexanol)
CIOH200
0.011
0.020
12
Nerol(2-cis-3,7-dimethyl-2,6-octadiene-l-ol) Phenylethylalcohol (2-phenylethylalcohol)
CiuH 1 x 0
0.0038
0.0047
21
C8Hw0
0.0019
0.0029
43
Phenylpropylalcohol(3-phenyll-propanol) C~HIZO CloHIRO Terpineol (I-methyl-4-iso-propyl-I-cyclohexene-4-01)
0.0024
0.0031
28
0.0074
0.012
22
Tetrahydrolinalool(3,7-dimethyl-octane-3-01)
0.025
0.01 1
13
Phenol
0.0028
0.0026*
45
p-Cresol
0.0035
0.0056*
23
CinHzzO
Icm2/sl
7.9
Phenols
2,4,6-Trimethylphenol
0.020
0.019*
23
2,3,5.6-Tetramethylphenol
0.026
0.030"
16
2,4-di-tert-Butylphenol
0.017
0.016*
1.2 9.8
2,6-di-tert-Butylphenol
0.14
0.13*
2,6-di-tert-Butyl-4-methylphenol
0.18
0.19*
6.6
Topanol (1,I ,3-tris(2-methyl-4-hydroxi-S-tertbutylphenyl) butane)
0.00060
0.00031*
0.054
CIOHI 2 0 2
0.015
0.012
26
CIffH1202
0.020
0.019
15.5
Aldehyde Cg (n-octanal)
0.021
0.020
23
Aldehyde CS (n-nonanal
0.026
0.026
18
Aldehyde Clo(n-decana1)
0.033
0.034
14
Aldehyde CII(n-undecanal)
0.042
0.043
10
eugenol(4-allyl-2-methoxyphenol) lsoeugenol(2-methoxy-4-propenylphenol) Aldehydes
Aldehyde C1,en(n-undecene-2-a1)
CI1Hzo0
0.042
0.043
9.6
Aldehyde CIlinter(cis-undecene-8-al)
CiiHzoO
0.030
0.024
9.0
Aldehyde Clz (n-dodecanal)
CizHz40
0.052
0.060
1.9
Permeation of gases, uwrt’r vcrpor and volutile organic cornpoiinds
267
Table 9-7 Continued
Compound
Molecular formula
D . 10’”
K calc.
exp. 0.059
Aldehyde CI2MNA(2-methylundecanal)
CI~HZ.~O
0.052
[CRI’k] 1.8
2-Pentyl-3-phenyl-propenal
Ci-tHixO
0.079
0.064
14
Citral (cis-3.7-dirnethyl-2,6-octadienal)
CIlIHlhO
0.022
0.016
36
Citronellal (3,7-dimethyl-6-ociene-l -al)
CIIIHIXO
0.023
0.019
10 16
Jasmonal (2-hexyl-3-phenyl-propenal) Ci d 2 1 1 0 Hydroxycitronellal (3,7-dimethyl-8-hydroxyoctanal)ClllHZ1102
0.10
0.10
0.00052
0.00090
5.5
Heliotropine (3.4-methylenedioxy-benzaldehyde)
CRHh03
0.032
0.019
8.7
Lilial (3-(4-tert.-butylphenyl)-2-methylpropanal)
CI4HZ00
0.032
0.014
0.0022
0.0018
Acetophenone(pheny1me thyl-ketone)
0.021
0.03
110
Benzophenone
0.063
0.046
4’)
Camphor (1,7,7-trimethyl-2,2,1-heptane-Z-on)
0.031
0.062
15
Ionone (4-(2,6.6-trimethyl-2-cyclohexene-l -yl)-3 butene-2-011)
0.070
0.039
12
Methylionone alpha (5-(2,6,6-trimethyl-2cyclohexene- 1-yl)-4-pentene-3-on)
0.0xx
0.060
6.6
(4-(2,6,6-trimethyl-2-cyclohexene-l-yl)-3-methyl-3butene-2-on)
0.088
0.066
8.6
Menthone (2-isopropyl-5-methyl-hexanon)
0.032
0.082
21
Methylheptenon (3-octene-2-on)
0.033
0.019
73
0.2
0. I
0.0009
0.001
25
OA14X
0.050
17
Lyral (4-(4-methyl-4-hydroxyamyl)-3-cyclohexene- CI3HZ2O2 carboxaldehyde)
14 1.2
Kmwze.7
Methylionone gamma
Tonalid (7-acetyl-1,1,3.4.4,6hexamethyltetrahydronaphthalene)
3.8
Acids
Phcnylacetic acid Nirrilrs Citralva(geranylnitri1e) (cis-3.7-dimethyl-2,6-octa-dicne-l -nitrile)
CioH IA’
268
Piringer
Table 9-7: Continued Compound
Molecular formula
D . 10"'
K calc.
cxp.
[cm2/s]
2-tert-Butylcyclohexylacetate
0.066
0.092
Aldehyde C16 (3-methyl-3-phenyl-glycid acid ethyl cstcr)
0.024
0.027
22
Allylcyclohcxancpropionate (allyl-3-cyclohcxylpropionate)
0.10
0.14
24
Benzilacetate (acetic acid-benzilester)
0.034
0.04
70
Benzilbenzoat (bcnzilic acid-benzil ester)
0.10
0.094
32
Cedrylacctatc
0.19
0.29
Citronellylacetatc (3.7-dimethyl-6-octene-l-yl acetate)
0.047
0.071
29
Citronclly Iformiate
0.038
0.086
23
DEP (diethylphthalate)
0.025
0.019
18
Dicthylmalonate
0.008
0.01 1
44
Esters 9.1
4.1
DMBCA (dimethylbenzil-carbinylacetatc)
0.067
0.049
109
DMP (dimethylphthalate)
0.016
0.012
19
Ethylbenzoate
0.034
0.070
11
Gcranylacetate (2,6-dimcthyl-2.6-octadiene-8-yl acetate)
0.075
0.068
16
Hexenylacetate cis 3 (cis-3-hexcne-1-yl-acetate)
0.019
0.041
93
IPM (isopropylmyristate)
0.21
0.33
17
Isoamylacetate
0.021
0.043
77
Isobornylacetate (1,7,7-trimethyl-bicylo-1,2,2heptanyl-2-acetate)
0.063
0.086
23
Linalylacetate (3,7-dimethyl-1,6-octadicne-3-yl acetate)
0.075
0.065*
12
Oryclene extra (p-tert-butylcyclohexylacetate)
0.064
0.1 1
12
Phenylethylacetate (2-phcnylethyl-acetate)
0.017
0.036
51
Phenylcthylphenylacetate Terpinylacetatc (l-methyl-4-iso-propyl-1-
0.052
0.033
30
0.046
0.088
12
Verdylacetate (dihydronordicyclo-pentadienylacetate)
0.058
0.089
21
Styreneacetate (1-phenylethylacetate)
0.043
0.040
29
Aldehyde C14 (undecalactone)
0.052
0.052
Coumarin (benzopyronc)
0.032
0.024
cyclohcxene-4-yl acetate)
Lactones 2.7 54
Permeation of gases, water vapor and volatile organic compounds
269
Table 9-7: Continued ~~
Compound
Molecular formula
D . 10"'
K
calc.
exp.
[cm2/s]
Ethers Anethol
CioHizO
0.23
0.24
50
Diphenyloxide (diphenylether)
Cl2HlOO
0.22
0.14"
37
0.23 C12H120 CI 1H1402
0.25 0.27
0.25
39
0.43
30
CnH 100 CI I Hi00
0.15
0.15
120
0.20
0.29
47
lndole (2.3-benzopyrrole)
CuH7N
0.013
0.0093
55
Methylquinoline (7-methylquinoline)
CICIHPN
0.019
0.027
43
Bromelia (O-naphthylethylether) Eugenolmethylether Cresylmethylether Yara Yara (methylnaphthylether) Heterocyclic compounds
The dimensionless partition coefficient K = cp/cL=S,, also known as a relative solubility coefficient, is defined as the ratio of the concentration of a substance in the polymer cp to that in the liquid (food) cLat equilibrium. While D is practically independent of the liquid phase in contact with the polymer in these measurements, the K values are determined by the nature of the polymer and liquid contact phases. From the definition S, = K, a relative peremeability coefficient can be calculated, P, = S, D, with the dimension D. Here, accordingly t o Eq. (9-2) and the solubility constant in the polymer and in the liquid phases expressed as Sp = cp/p and SL = cL/p, respectively, the following relationship results between the absolute and relative permeability coefficients:
P
= P,SL =
KDSL =
D CL
P
= SpD
(9-32)
The best agreement between the permeation process and the simplest diffusion model, for example Eq. (g-l), forms the foundation for steady state. This is obtained for a permeant above its critical temperature, at low partial pressures, in completely amorphous polymers above their T,, containing no fillers or substances to cause swelling. Deviations are often observed for organic compounds permeating through polymers below their T, as well as up to temperatures 10°C above their T,. Let m, represent the amount of material absorbed or desorbed in a polymer membrane up to time t; and mo and me represent the amount of material found in the membrane at the beginning of the experiment (t = 0) and after reaching equilibrium (t = m where me = mo+ m-). Then one obtains the same curves for m, as a function of the square root of time t for both sorption and desorption within the applicability of the simple law of diffusion (constant D) shown in Fig. 9-2a. It does not matter whether one measures the absorption curve A or the desorption curve D, for both are the same. After a linear increase, the curves converge asymptotically to an equilibrium value. Every deviation or difference (hysteresis) between curves A and D can be explained in terms of deviations from the simple law of diffusion.
Piringer
Figure 9-2: Several sorption (A) and desorption (D) curves. a) normal diffusion with constant D-value; b) increasing D-value with increasing permeant concentration; c) decreasing D-value with increasing permeant concentration: d) sorption with pronounced swelling: e) concentration- and time-dependent diffusion coefficient.
When the diffusion coefficient increases with increasing permeant concentration, then A lies above D (Fig. 9-2b). This deviation is observed for most organic substances at higher concentrations even though no significant polymer swelling yet takes place. However when D decreases with increasing permeant concentration, for example for the diffusion of water vapor through weakly polar polymers (see 9.2), the D curve lies over the A curve (Fig. 9-2c). The sorption process can be coupled with a significant swelling. Then the A curve has a sigmoidal shape and desorption follows the simple law of diffusion with a relatively high initial rate (Fig. 9-2d) (Felder and Huvard, 1980). The sorption coefficient (solubility constant) is obtained using Eq. (9-7) and the equilibrium values of me and pe. Its independence from the concentration or partial pressure of the permeant can be tested as previously described. If one plots the ratio of m,/m, against t”*, the concentration independence or constancy of the diffusion coefficient can be tested. With a constant D, the curve starts out linear as in Fig. 9-2a. For a permeant passing through a polymer sample with any given geometry, having a surface area A and volume V, one obtains a good approximation from the law of diffusion: (9-33) This expression gives an alternative possibility to Eq. (9-9) for calculating D. If the ratio m,/m, varies linearly with t then this is an indication of a deviation from normal behavior. The sorption isotherm for many substances in polymers in the glassy state, as well as water in cellulose, can be described by two processes that are independent of one another (dual sorption model): (9-34)
Permeation of gases, water vapor and voliitile organic compounds
271
where c, is the total concentration of the permeant in polymer at partial pressure p, at equilibrium. According to Henry’s law (Eq. 9-3) the sorption process with the solubility constant S is superimposed by an adsorption process. This adsorption process can be described by a Langmuir isotherm with constants a and b. At very small partial pressures, the adsorption on the surface and/or active sites within the polymer matrix dominates (Demertzis, 1985). However at high pressures the solution in the polymer determines the process. One consequence of such behavior can lead to a permeability coefficient that is dependent of the film thickness. Because this type of deviation from the simple law of diffusion, it is not surprising that P values for the same polymer can vary from one another by an order of magnitude depending on the measurement method and test conditions. Through the uptake of a substance in a polymer matrix, time dependent changes in the polymer matrix can take place, particularly at high concentrations. As a consequence, the diffusion coefficient can be time- as well as concentration-dependent. One observes such behavior for example by the sorption of substances that lead to swelling at temperatures below the T,. After a relatively rapid approach to an apparent state of equilibrium one observes a slow change towards the actual equilibrium (Fig. 9-2e). These two-step processes are caused by a gradual loosening of the cohesive forces between the macromolecules.
9.3.2 Measurement of partition and diffusion coefficients The dimensionless relative solubility constant S, = K in Eq. (9-32) is a measure of the partitioning of a substance between two phases, as is the absolute solubility constant coming from Henry’s law in Eq. (9-3). The absolute solubility constants can be directly determined using one of the methods for gases, but this is limited to only relatively volatile substances. Large experimental errors like adsorption on the polymer surface and cell walls cannot be avoided in these methods for substances with low volatilities. A measurement system where the substance studied goes from a gas phase through the film and into a second gas phase is shown in Fig. 9-3 (Franz, 1992). The permeant is dissolved in a very non-volatile substance, e.g. polyethylene glycol, in the low cell chamber in order to keep the concentration of the permeant as low as possible in the gas phase and therefore avoid the polymer swelling. The amount of permeated substance is carried to a sorption column by stream of gas flowing through the upper cell chamber. After certain time intervals the amount of sorbed material is extracted and measured using a gas chromatograph. After reaching a steady state in the membrane, the evaluation of the data proceeds in the same manner as described for gases. S and D can be calculated either by using the time lag method (Eq. 9-9) or through combination with an equilibrium sorption measurement of the film at the corresponding permeant partial pressure. As a rule several organic substances can be studied simultaneously, as long as there is no influence of one over an other (i.e. they are measured at very low partial pressures) and it is possible to separate them on a gas chromatograph. Even when swelling processes are avoided, particularly for less volatile substances and certain structures, the differences between permeation measurements made over a gas phase and those made in direct contact with a liquid can be anticipated. The
272
Piringer
c
nitrogen (65% ch.)
permeent reservoir Figure 9-3: Device for permeation measuring of organic vapors.
cause of this difference is the behavior of the permeant on the film surface in the presence of a gas compared to a liquid phase. Theoretically the partition between the polymer and a liquid can be divided into two independent partition processes, one for each of the two contact phases with a gas phase having the same partial pressure. But in practice, different results are obtained because of surface boundary effects. Therefore, for all liquid products where there is direct contact between the liquid and packaging, permeation measurements should be made under similar conditions. The following method, known as the pouch method, is very simple to conduct and delivers adequate accuracy for practical purposes (Becker, 1983). One forms a pouch with the plastic film by sealing three sides. The pouch is then filled with a dilute solution containing the permeants in a solvent and the fourth side is then sealed. In addition to the liquid phase, a gas headspace is also often present in the pouch. The pouch is then immersed in 500 to 1000 ml of pure solvent contained in a 1 L wide mouth flask with stopper. The solvent is stirred using a magnetic stirrer for the duration of the test. For films with very low permeabilities, the stirrer is not needed since the diffusion of the permeant in the solvent is much greater than that in the film, such that no significant concentration gradient can exist in the liquid phase. At suitable time intervals 0.5 to 1.0 ml samples are removed from the solvent surrounding the pouch and analysed by gas chromatography. Calculations are carried out using the following equation, which is for a quasi steady state of permeation from a volume Vi of permeant solution in the pouch into a solvent volume Va surrounding the pouch: (9-35)
In the quasi steady state, the very slight concentration changes occuring over time in the two solvents can be taken into account through a simplified permeation calcula-
Permeation of gases, water wpor and volatile organic compounds
273
tion. Here A is the surface area and d the thickness of the pouch material, c, is the concentration at time t in the external phase and c, is the concentration at equilibrium. The apparent uncertainties in Eq. (9-35) result from the value of A used, due to the presence of the gas headspace volume in the pouch. In the first approximation the partition coefficient can be calculated at equilibrium between the inner pouch surface area, the liquid and the gas phase as K = c p / c =~ (cp/p)/(cL/p) = Sp/S=. For this assumption it is the same, whether the permeant goes directly into the plastic or into the gas phase and then into the plastic. In order to recognize possible systematic errors when making permeation measurements with the pouch method, studies are carried out using the sorption technique. This method follows the non-steady permeation state. To do this, plastic disks are brought in contact with a solution of permeants and the uptake of permeants in the plastic is followed over time. The disks are stamped with a hole in the middle out of the plastic being studied, using a punch. They are then placed on a glass rod and separated using glass rings to prevent the disks sticking together during the study. This plastic assembly is then placed in a suitable screw cap glass vial containing the permeant solution (Till et al., 1987). During measurement, the vials are placed on a shaker. After a given time the disks are removed from the solution, quickly dried with absorbant tissue and washed with a suitable solvent to remove residual solution. The disks are then extracted to remove the absorbed permeants using a solvent that swells the polymer. The evaluation of the sorption curve during the initial sorption phase uses the equation: (9-36) where ct is the concentration of the permeant in the plastic at time t (see Chapter 11). The formula has the same form as Eq. (9-33) so that D can be checked for constancy. At small permeant concentrations D can be practically guaranteed to be constant (Fig. 9-2a). This method for measuring the change in sorption over time cannot be used to measure polymers that absorb permeants very quickly like LDPE, since it produces large errors. In any case the sorption method is suitable for determining of the equilibrium concentration c, of permeant in the polymer and consequently for the measurement of K.
9.3.3 The significance of partition coefficients The value of the partition coefficient of a substance between two phases depends mainly on the polarity of the substance and the polarity of the two media. Using the rule of thumb “like dissolves like” one tries, when selecting a plastic packaging material for example that will come in contact with an aqueous product, to select a nonpolar polymer (e.g. polyolefin) so that it will not be attacked by water. In such a system strongly polar substances prefer the product phase and non-polar substances prefer the packaging material. Between the extremely polar substance, water, and the completely unpolar hydrocarbons in this respect one finds the smaller alcohol molecules. Methanol and ethanol are particularly suitable for the determining the relative solubilities of organic compounds in plastics. They are themselves good solvents for
274
Piringer
many substances, they have no significant interactions with non-polar plastics and are practical to work with analytically. Ethanol in particular can be used as a food simulant for fat-containing products as will be shown later. It can also be used as a fat simulant for the study of polar plastics, on the addition of particular amounts of water. In order to determine the most important influences on the partition coming from the structures of the permeant molecules, 12 compounds have been selected from Table 9-7 and studied closer under different aspects. The selection contains compounds with different functional groups and molecular structures. An additional important criterion for the composition of this mixture is they can be easily separated into individual components by gas chromatography. By doing this, four to eight compounds could be measured simultaneously. Comparisons with measurements made using individual compounds showed no difference beyond measurement uncertainty, up to a concentration of 1 to 2 % (mass fraction) in methanol. It can be seen from the data in Table 9-8 that the partition coefficients of the selected compounds show no significant differences with respect to the liquid phase used. The values for the unpolar limonene are slightly higher in the polyolefin/methanol system than in the polyolefin/ethanol system because the methanol has a higher polarity than ethanol. For the polar cis-3-hexenol compound this difference disappears. Table 9-8: Partition coefficients of organic compounds with different polarities between polyolefins and ethanol or methanol. LDPE Compound
Eth.
HDPE
PP
Meth.
Eth.
Meth.
Eth.
Meth.
Limonene
0.42
0.67
0.36
0.74
0.4s
1.0
Diphenylmethane
0.25
0.27
0.24
0.27
0.20
0.33
Diphenyloxide
0.14
0.23
0.16
0.23 0.043
0.22
0.27
0.10
0.11
-
Isoamylacetate
-
0.046
Aldehyde C14
0.017
0.052
0.035
-
0.030
-
Linalylacetate
0.065
0.058
0.067
0.059
0.066
0.055
Camphor
0.064
0.062
0.057
0.07
0.042
0.12
Eugenol
0.013
0.012
0.024
0.02
0.020
0.015
Dirnethylbenzilcarbinol
0.0062
0.012
0.017
0.012
0.013
0.0088
Menthol
0.0087
0.02
0.019
0.014
0.018
0.018
2-Phenylethylalcohol
0.0028
0.0097
0.011
0.007
0.0087
0.0074
cis-3-Hexenol
0.0024
0.0024
0.014
0.003
0.0062
0.0037
An important point for the estimation purposes is that there is only a very small difference between the partition coefficients in the polyolefins LDPE, HDPE and PP. When the partition coefficients are expressed relative to LDPE (the straight line drawn in Fig. 9-4a) then the values for HDPE and PP are grouped around LDPE, whereas the values for PVC are significantly greater (Kozinowski and Piringer, 1986). The differences in the relative permeability coefficient and degree of crystallinity of the corresponding polyolefins in Fig. 9-4b can be traced back principally to the strong dependence of the diffusion coefficient on the characteristics of the polyolefins in Fig. 9-5 (P, = K D).
PVC
HDPE, PP
-c
KLDPE
b
LDPE
10-10 HDPE PP- cop. PP-homop.
-F
g lo-”
I
d
I
PVC
lo-” 1013
-
10-11
pr, LDPE
10’0 [cmZ/sl
Figure 9-4: Partition and permeability coefficients relative to LDPE. a) partition in the systems polyolefinlethanol and PVC/ethanol: b) permeability in polyolefins and PVC. 1: cis-3-hexenol. 2: phenylcthyl alcohol, 3: eugenol, 4: isoamyl acetate. 5: undccalactone. LDPE
108
IPE
10
T
‘-Cop.
% 10
I-homop.
Y
O
t
-11
lo I
1
1
!
! ! ! ! !
I
I
I
I
I I I I I
lo-’*
10-13
I
PVC
1O Q
10-8
DLDPE Icm2/s]
Figure 9-5: Diffusion coefficients in polyolefins and PVC related to LDPE. The numbers corresponds to the compounds in Fig. 9-4.
276
Piringer
Since the measurement of the partition coefficients for LDPE goes much more rapidly than for the other polyolefins, it is practical to apply the K values obtained for LDPE to other polyolefins. This can be done without any large errors. Table 9-9 lists the partition coefficientsfor the 12 selected compounds between LDPE and PVC polymer phases and ethanol and aqueous ethanol mixtures as liquid phases. Here one can see the enormous influence of water, particularly on the slightly polar substances in contact with the unpolar LDPE. The cause of this is the increasing permeant partial pressure over the solution with increasing water content where according to Henry’s law (Eq. 9-3) the concentration of the permeant in the polymer is proportional to the partial pressure. The non-polar permeant molecules have much less affinity for aqueous solutions than other more polar permeants. The results appear to be a regular “expulsion” of these molecules from the solution and an “attraction” by the plastic. This effect is not as strong for polar substances like cis-3-hexenol and phenyl-ethyl-alcohol.The effect is also much smaller for PVC, which has a greater polarity relative to LDPE, and whose affinity for unpolar molecules is also less. The relationship between permeant and solution is described with help of the generalized Raoult’s Law: (9-37)
P = YXPO
where x is the mole fraction of permeant in the solution, po is the vapor pressure of pure permeant at the same temperature and y is the activity coefficient. With Eq. (93) then one obtains: cp = Syxp”
(9-38)
For an ideal solution y = 1, and the equilibrium concentration of the permeant varies proportionally to the mole fraction over the complete mole fraction range. A practically ideal system is for example a solution of heptanol in methanol (Fig. 9-6). Table 9-9: Partition coefficients of organic compounds between polymers (LDPE, PVC) and several ethanol/water-mixtures at 23 “C. Compound
LDPE Eth.% 100
LDPE 80
LDPE 60
LDPE 40
LDPE 20
PVC 100
PVC 40
PVC 20
30.0 15.0
110.0 -
~
275.0
Limonene
0.42
1.99
6.5
9.7
Camphor
0.064
0.089
0.15
0.44
5.0
0.6 0.4
0.86
-
0.2
~
Linalylacetate
0.065
0.15
0.59
0.46
Diphenylmet hane
0.25
0.82
3.7
6.6
560.0
2.3
69.0
Isoamylacetate
0.046
0.069
0.16
0.99
4.1
3.3
5.2
Citronellol
0.026
0.011
0.052
0.27
3.1
1.2
180.0
17.0
2.1 150.0
0.93 -
11.0 9.1
Diphenyloxide
0.14
0.51
1.7
Eugenol
0.013
0.023
0.047
0.26
1.5
3.6
4.9
Aldehyde C14
0.017
0.030
0.073
0.72
10.0
11.0
31.0
cis-3-Hexenol
0.0024
0.0034
0.0058
0.025
0.077
0.07
0.16
0.33
Menthol
0.0087
0.020
0.053
0.45
5.4
0.05
0.43
0.32
Dimethylbenzylcarbinol
0.0062
0.0096
0.017
0.075
0.32
0.15
0.23
0.15
Phenvlethvlalcohol
0.0028
0.0045
0.0059
0.019
0.098
0.21
0.37
1.5
20.0
-
9.8 -
Permeation of gases, water vapor and volatile organic compounds
-
277
x Heptanol
Figure 9-6: Dependence of the equilibrium concentration of heptanol in LDPE from the mole fraction in methanol ( 0 ) and water (m).
On the other hand a solution of heptanol in water is not ideal and y>> 1. According to Eq. (9-38) the cp of heptanol in LDPE in contact with a dilute aqueous solution is much larger than that for the same concentration of heptanol in methanol (Fig. 9-6). Table 9-10 shows how different the K values can be for a given permeant with different solvent liquid phases. Upon going from methanol to an organic solvent having less polarity, the K values increase due to the increasing deviation from the ideal (y > 1). A closer relationship exists between heptanol and both alcohols and ketones than with the non-polar hydrocarbons because of their polar OH groups. Nevertheless, even with this polarity the difference with water, which is even more polar, is much larger. As a result, after partitioning between LDPE and water, the water contains no residual hydrocarbons. Table 9-10: Solvent dependence of the relative permeability and solubility exemplified with heptanol in LDPE at 23 "C. ~
Solvent Water
P, ' 10'" (crn'/s) 95
K . 10' 155
Methanol
0.24
0.44
Ethanol
0.25
0.47
1.7
2.5
Acetone Benzene
430
n-Hexane
975
6.8 16
The K values increase rapidly for completely unpolar n-alkanes with increasing water content (Table 9-11). Because of the very low solubility of hydrocarbons and most organic compounds in pure water, the partition coefficients for LDPE/water are either obtained by extrapolating the K values from Table 9-10 to 100 % water, or calculated from two independent measurements of the partition coefficients between
278
Piringer
LDPEloctanol (KpIO)and octanol/water ( K ~ I WThe ) . partition coefficient for LDPE/ water (KpN) results then from KP/W= K p ~ o. Ko/w (Table 9-12). Table 9-11: Increase of K-values of n-alkanes with increasing water concentration in ethanollwater mixtures. 60 % Eth.
40 Yo Eth.
20 Yo Eth.
3.5
160
4200
20000
6.5
370
27000
80000
900
120000
280000
7600
1100000 -
-
Compound
100'Yo Eth.
Decane
0.55
Dodecane
0.97
Tetradecane
1.3
11
Hexadecane
1.6
20
80 % Eth.
Octadecane
2.5
35
34000
780000 330000
Eicosane
4.2
59
160000
830000
Table 9-12: Partition coefficients of some aroma compounds between LDPE and octanol and between octanol and water at 23 "C. Compound
LDPElOctanol
Octanol/Water
LDPE/Water calc.values
LDPE/Water extrapol.values
Limonene
0.15
35000
5300
loo00
Camphor
0.062
180
21 1
60
Diphenylmet hane
0.15
19000
2850
4000
Isoamylacetate
0.05
Citronellol
0.0093
Diphenyloxide
0.13
Eugenol
0.021
243
Aldehyde C14
0.022
1600
cis-3-Hexenol
0.0006
175
9.0
19
2600
21
30
11000
1430
1150
34
5.0 35 0.33
21
7.5 115 0.22
Menthol
0.013
1600
Dimethylbenzene-carbinol
0.014
73
1.o
1.14
Phenvlethvl-alcohol
0.013
29
0.38
0.5
70
The consequences of the above results on the partition of aromas and aroma compounds between products and a plastic package can be seen in the values in Table 9-13. It can be seen from the partition coefficients that the values for medium polarity to non-polar substances partitioned between the two wine samples and LDPE are one to two orders of magnitude greater than the partitioning of the same substances between milk and LDPE (limonene, diphenylmethane, diphenyloxide, linalylacetate). The coefficients for the polar substances (cis-3-hexeno1, phenyl ethyl alcohol) show comparatively no difference. The K values for non-polar substances partitioned between milk and LDPE are comparable with values obtained for partitioning into 50% ethanol. Despite the relatively low fat content of whole milk (3.5 %), milk behaves quite differently from wine (Kozinowski, 1989). While wine represents a real aqueous solution whose behavior is determined by its water content, milk is not only aqueous but also a fat containing food which, because of its aqueous
Permeation of gasess water vapor and volatile organic compounds
279
external phase does not swell the polyolefin. The reason for this ambivalent behavior lies with the fat in water emulsion structure of milk. This explains why polar as well as non-polar substances are so well dissolved in milk. In both cases this leads to a decrease in their partial vapor pressure over milk, thus leading to the observed partition coefficients. Table 9-13: Partition coefficients of several aromas in the system polyolefineiaqueous food at 23 "C.
Compound Limonene
Skim milk (1.5 % fat)
Whole milk (3,s % fat)
LDPE
HDPE
LDPE
HDPE
10
12
4.8
7.2
3.5
-
Camphor
6.8
Linalylacetate
5.7
-
2.4
Diphenylmethane
5.7
6.0
2.5
Isoamylacetate
2.3
3.1
I .8
1.s
Citronellol
2.3
2.0
1.x
5.9
Diphenyloxide
7.6
9.6
2.3
2. I
Eugenol
1.3
1.s
1.1
0.96
Aldehyde C 14
2.0
3.5
1.3
1.1
cis-3-Hexenol
0.18
0.20
0.16
0.12
Menthol
-
-
Dime thylbenzylcarbinol
3.1
1.2
1.2
Phenylethylalcohol
0.18
0.11
0.12
Compound
0.2 1
3.8
Wine (5.3 % Eth.)
Wine (8 % Eth.)
LDPE
LDPE
HDPE
HDPE
I 100
1000
5000
Camphor
-
-
-
Linalylacetate
-
-
-
-
2100
2300
830
1600
Limonene
Diphenylmethane lsoamylacetate
4.5
Citronellol
5.9
Diphenyloxide Eugenol Aldehyde C 14
74 2.4 34
5.4 13 125 2.8 77
4.7 5.1 28 18
12
5.3 12 61 4.7 190
cis-3-Hexenol
0.08
Menthol
4.6
Dimethylbenzylcarbinol
0.34
0.67
0.44
0.65
Phenylethylalcohol
0.15
0.30
0.20
0.22
0.20 18
0.09 7.1
0.20 18
In Fig. 9-7 the concentrations of styrene in either aqueous ethanol or milk versus the percentage ethanol or fat are plottcd in a bar chart (O'Neill et al., 1994). The values were measured after 10 days contact at 30 "C with identical PS samples in contact
280
Piringer
-milk
nethanollwater
I %
fat content
ethanol percentage
Figure 9-7: Concentration of styrene in aqueous ethanol and milk after lOdays in contact with PS at 30°C.
with the same volumes of the two liquid phases. This result further confirms the similarity between whole milk with 3.5 % fat and 50 % aqueous ethanol with respect to the partition of low polarity substances in such systems. Like the size of the K values of the model substances, the partition process plays a role in mass transfer in packaging material/milk systems only for extremely non-polar substances. The loss of volatile milk components, mostly low molecular weight alcohols and ketones, through the packaging has no practical significance because of the small K values expected. On the other hand, this relationship plays a big role in the transfer of substances contained in the packaging into the food. The migration of dioxin into the milk fat phase is an example of this. The partition coefficients of this group of substances are very small in the polyolefin/milk system because of the fat phase in comparison to the polyolefin/water system. In comparison, significant losses of a number of wine components must be expected when in contact with polyolefins because of the large K values for non-polar compounds. Packaging wine in polyolefin-coated containers, which for example is the case for bag-in-box packaging, does not appear to make sense. Quality decreases can occur not only by loss of the aroma but by the alteration of the aroma character due to different K values for different aroma compounds. The uptake (scalping) of non-polar compounds like limonene from fruit juices by polyolefins has been experimentally confirmed (Hirose et al., 1988; Mannheim et al., 1988). While permeation of organic substances through a plastic container occurs very slowly, the enrichment of product components in the plastic near the material’s surface can occur after just a short contact time for plastic/product systems with large K values. When suffering a loss in quality, the product component need not necessarily be transported through the container wall and into the external atmosphere. The use of a thicker wall of the same plastic is not the solution in such a case. More important here is the selection of polymer, which should have a diffusion coefficient as small as possible, so that the thickness of the diffusion front in the plastic stays as small as possible during the intended storage time.
Permeation of gosees, writer vapor and volatile organic cornpoitndh
281
Partition processes like the types described above play as big a role in liquid cosmetics and cleaning formulations as in packaged foods. Table 9-14 contains the relative permeability coefficients P, of various aroma compounds through LDPE in contact with a liquid dish-washing detergent (with water as its main component), a skin cream and with methanol, all containing the same aroma compounds. Most of the values are much higher in the detergent than in methanol. This can be easily described using explanations found in the above discussion. The more unpolar the aroma compound, the greater the difference between the detergent and methanol. In comparison to both of these phases the P, values of aroma compounds in the same LDPE in contact with the skin cream are almost all much smaller. Because the product components are so soluble in a fat phase they remain in the cream. Table 9-14: Relative permeability coefficients of several aromas in the systems LDPElcleaning agent, LDPElmethanol and LDPElskincreme at 23 "C. Compound
Cleaning agent
Methanol
Skincreme
P, . 10"cm2/s 1 2 3 4
5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
-
-
-
-
-
-
-
-
33 46 68 57 20 7.3 28 20 91 114 20 150 87 38 70 22 2.3 8.6 0.6 2.3 310 20 22 56 21 21 364 23
-
0.11 0.17 2.4 0.27
-
1.9 10 32 5.4 29 1 4.5 2.2 1.1 34 12 3.6 3.3 4.3 42 -
2.7 52 11 8.3 9.9 4.4 5.5 35 3.9
-
0.27 0.12 0.36 0.51 0.59 0.22 0.29 0.23 0.14 1.7 -
282
Piringer
The consequences of partitioning processes in package/product systems must also be considered in the case of returnable and recycled packaging. Because diffusioncontrolled transport processes take place relatively slowly, one cannot rule out the transport of product components absorbed during the previous use storage eventually diffusing back into the freshly filled product, even if the container was washed between uses. Such substance traces can also include reaction products of earlier absorbed components with oxygen and can lead to diminished quality in the newly filled product through the creation of off-odors. Traces of substances absorbed during the storage of various chemicals can have negative consequences in recycled materials. In general such cases have seldom been observed. Model studies in our laboratory have shown that mass transfers of this type are as a rule very small and can at most exert an influence from only the sensory point of view. Nevertheless, mass transfer of substances in lower density polyolefins is more likely to lead to negative influences because of the high D values. In view of the variety of molecular structures and the very different use conditions that need to be considered with regard to interactions, one is forced towards the idea of developing partition estimation methods that have adequate accuracy for practical purposes. Estimations based on experimental data collections are possible. Several simple expressions have already been presented for estimating D and S values for gases. In Chapter 4 estimation methods for partition coefficients are treated in more depth. In conclusion it must be emphasized here that the values of partition coefficients of permeating substances cover a range of more than 9 orders of magnitude (lo-* to 10’) dependent on their structure and the polarity of the filled product and packaging material (e.g. polyolefinsiwater); and this is only for a single polymer (e.g. LDPE). This means that in practice, the importance of the partition coefficient in the permeation of organic compounds is often not given the attention it deserves.
9.3.4 The significance of diffusion coefficients Compared to the partition coefficients the values of the diffusion coefficients of organic compounds in a given polymer cover a relatively small range (approximately three orders of magnitude for the values of the compounds listed in Table 9-7 in LDPE at the same temperature). At the same time the D values for a given permeant depend on the nature of the polymer, like that shown for the simple gases, and can range over 8 orders of magnitude. Given that P = S D or P, = K D, there theoretically results an enormous range of values for the permeation coefficient as a function of permeant molecular structure, product and packaging. In practice the extreme values do not lie so far apart because the tendency of the diffusion and partition coefficients to oppose each other reduces the differences between permeation values. The good solubility of a permeant in a polymer is due to a relatively strong attraction between permeant and macromolecule. At the same time the mobility of the permeant molecule and consequently its D value decreases. Such a case was mentioned in the discussion of water vapor permeation. In the development of estimation methods for D values, two independent contributions must be taken into consideration: on one side, the size and shape of the per-
Permerttioti of gases. wnler vapor and voIniiIe orgrmic conipoiinds
283
meant molecule and on the other, the attractive forces between the permeant and macromolecule. If the concentration of a highly soluble permeant increases so much in a polymer that swelling takes place, diffusion is made easier through a loosening of the polymer matrix. For this reason methanol and ethanol were selected as the contact phase for studying permeation of organic compounds in polyolefins. When one compares the D values in Table 9-15 for undecane in LDPE in contact with methanol, acetone and hexane, then the increasing solvent swelling effects with decreasing polarity can be plainly seen. The difference between hexane with and without pre-swelling of the polymer matrix shows the time-dependent character of the swelling process. Tahle 9-15: Solvent dependence of the diffusion coefficients of undecane in LDPE at 23 "C. Solvent
D . 10" (crn2/s)
n-Hexane (pre-swelling)
530
n-Hexane
66
Acetone
13 9.0
Methanol
When one plots the D values of various different compounds versus their relative molecular mass, M,., for a given polymer, then the values for the n-alkanes lie on the upper limit of diffusion (Fig. 9-8). This result means in practice that one has a maximum value for a variety of compounds with similar molecular weights when the nalkane diffusion coefficients are known. In a first approximation one can assume the ratio of the D values between a gas, for example carbon dioxide, and a n-alkane with the molecular weight M, to be constant and independent of the polymer. Given the existence of values for simple gases in a large number of polymers (Table 9-2) the
1 Of
0
10-5
t I
1
1
1
1
1
I
I
I
I .
lb u
M,
Figure 9-8: Diffusion coefficients of organic compounds in LDPE depending on their relative molecular mass. M,. C-6 to C-24 are hexane to tetracosan: 1: undecalactone, 2: phenylethyl alcohol. 3: isoamyl acetate, 4: diphenyl methane. 5: diphenyl ether, A: 7-OH to 18-OHare alcohols (heptanol to 1-octadecanol).
284
Piringer
order of magnitude of D values can be estimated for compounds in polymers for which no experimental data exist. This is particularly the case for barrier plastics whose diffusion measurements can be very time consuming (see Chapters 6 and 15). Equation (9-16) is valid for permeation through laminate structures. Even though our measurements for a series of coextruded laminate films gave good agreement with calculated values it was clear that for example the use of adhesives (Ad) in laminates can lead to deviations. The type of problems that can occur as a result can be described using a PE/Ad/OPP laminate film as an example. In Table 9-16 the relative permeability coefficients P, measured for PE and OPP homopolymers as well as the laminate are compared with the calculated P, values of a hypothetical PE/ OPP laminate (without adhesive Ad). Because according to Eq. (9-16) the total permeation of a laminate is determined by the lowest permeability of a material in the laminate, the OPP layer must be the layer controlling the permeation process. A “disturbance free” permeation process was measured and compared to the result calculated for a laminate containing no adhesive using Eq. (9-16). It was found that the P, value for the actual laminated film was a factor 3 to 40 times larger. Table 9-16: Relative permeability coefficients P, [cm2/s] . 1012 of 7 aroma compounds with different polarities (solved in methanol) in a laminate PEIAdlOPP of 62 pm (40/2/20)at 23 “C. Measured Compound
Isoamylacetate Limonene
Monofoil
Calculated Laminate
Laminate
PElAdlOPP (40/2/20)
PE/OPP (40/20)
PE
OPP
215
0.50
6.9
1.5
1651
2.16
20.9
6.5
cis-3-Hexenol
17.6
0.09
2.0
0.3
Linalylacetate
53.9
0.07
2.0
0.2
Menthol
10.4
0.01
1.2
0.03
8.3
0.01
1 .o 10.6
0.03
Citronellol Diuhenvloxide
595
1.20
3.6
Resulting from a comparison of the measured and calculated partition coefficient values K, the laminate containing adhesive dissolved significantly more aroma compounds than the PE/OPP laminate without adhesive (Table 9-17). Relatively high K values can be calculated for the adhesive layer. Due to the uncertainties connected with the calculation of K values in an extremely thin and possibly non-homogeneous adhesive layer, these values must be cautiously interpreted. The characteristics of the contact layer between the two mono films cannot be differentiated between an extremely thin and discrete adhesive layer at high permeant concentration and a mixed phase diffuse mono adhesive layer with a somewhat lower permeant concentration. One last possibility leading to a reduction in the effectiveness of the barrier layer could be the possible swelling effect occurring at the surface of the contact layers. This at the same time explains the higher observed P, values and appears to be more plausible (Thalmann, 1990). In any case the observed enrichment of the permeant in the region of the adhesive can have detrimental effects on the properties of the packa-
285
Perntearion of gases, wciter vnpor nnd volatile organic conipounds
ging. Along with more or less expressed changes in permeability, delamination (cloudiness, bubble formation) can occur as a result. The above example underscores once more the importance of distribution processes between the packaging and products which does not occur in the case of simple gases with very low solubility. Tablc 9-17: Partition coefficients K . lo2 of 7 aroma compounds with different polarities between a laminate PE/Ad/OPP with 62pm thickness (40/2/20)and methanol at 23 "C. Measured Compound
lsoamylacetate Limonene
Monofoil
Calculated Laminate
Laminate
PE
OPP
PE/AdlOPP (40/2/20)
PE/OPP (40120)
Ad
3.9
8.4
10.5
5.4
164
52.4
68.8
64.8
57.9
272
cis-3-Hexenol
0.2
0.9
4.9
0.5
137
Linalylacetate
5.2
10.1
11.9
6.9
163
Menthol
0.6
1.7
5.8
1.0
150
Citi onellol
0.2
1.3
5.3
0.5
147
13.5
1Y.6
25.7
15.5
332
Diphrnyloxide
References Becker K., Koszinowski J.. Piringer 0. 1983, Dt,sc.h.Lebensni.-Rundsch. 79 257-266. Brandrup J., Immergut E.H. (eds.) 1989, Polymer Hiindhook 3'd ed. John Wiley & Sons. Demertzis P.. Kontominas M. G., Voudouris E.K. 1985,J Food Technol. 20 419428. Felder R. M.. Huvard G.S. 1980. Permeation, diffitsion and sorption of gases and vapors in Methods of experimental physics, 16e. 315-377, Academic Press Inc. Franz R. 1993, Packag. Technol. Sci. 6 91. Hennessy B.. Mead J.. Stening T. 1966. The permeability of plastics films, London: The Plastic Institute. Hirose K.. Harte B. R., Giacin J. R., Miltz J., Stine C. 1988. in: Hotchkiss J. 1988, Food and packaging interactions, Am. Chem. Soc.. Washington, p 2841. Koszinowski J.. Piringer 0. 1986, in: Mathlouthi M. (ed) 1986, Food packaging and preservation. Theory and practice, London, Elsevier Applied Science. Koszinowski J., Piringer 0.1989, Verpackungs-Rrmdrch.40 3 9 4 4 (techn-wissensch. Beilage). Leibl S., Ewender J., Piringer 0. 1990, Verpack.-Rirndsch.41.1-3 (techn.-wissensch. Beilage). Mannheim C. H., Milk J., Passy N. 1988, in: Hotchkiss J. 1988, Food ond packaging interactions, Am. Chem. Soc., Washington, p 68-82. O'Neill E.T.. Tiohy J.J., Franz R. 1994,Inr. Dairy J. 4 271. Salame M. 1961, Trans folym. Eng. Sci.1 153. Thalman W.R. 1990,Packaging TechnoLand Science 3 67-82. Till D.. Schwope A,.. Ehntholt D., Sidman K., Whelan R., Schwartz P., Reid R. 1987, CRC Critical Reviews in Toxicology 18 161-188. Van Krevelen D. W. 1990, Properties of polymers. Their correlation with chemical structrire; their numerical estimation and prediction from additive group contributions (3th ed). Elsevier, Amsterdam.
Reactivity in Molecular Crystals Edited by Yuli Ohashi Copyright @ K d a o r h a Ltd .Tokyo. 1999
10 Migration of plastic constituents Roland Franz
10.1 Principles of migration testing The purpose of migration testing is to ensure food safety and protect the consumer, by controlling the levels of undesirable constituents from the packaging entering foodstuffs. Applicants and users of migration tests are in the first instance industrial laboratories, such as from polymer or plastic additives producers. But manufacturers of packaging materials such as bottle and film producers as well as converters also apply or commission migration testing to demonstrate compliance with food law, for quality assurance purposes or for submission of new product petitions. Finally and, in principal, with highest responsibility, the end-users of food packaging, the food industry themselves, need migration tests. However, normal practice is that they request and receive food law compliance certificates from the industries mentioned above. As another group of laboratories involved in migration testing, independent certifying laboratories as well as public or governmental control and surveillance labs must be mentioned. Before proceeding in the discussion about migration test principles, one needs to establish some definitions. The term “migration” is used to describe the process of mass transfer from a food packaging material to its contents. During the migration process a packaging material, in general, withstands the food contact conditions and does not alter its mechanical or diffusion properties too significantly. The term “extraction” is often used in the same sense as “migration” which may lead to confusion in the context with solvent extraction of packaging materials. Therefore the term “extraction” is defined in the following as a very intensive interaction process between a packaging material where solvent penetrates the packaging material and alters its mechanical and diffusion properties significantly and even extremely. If one reduces the migration process to the diffusion in and from plastics then the migratability of plastics constituents (organic substances) corresponds predominantly to the volatility or molecular weight of these organic substances and to the basic diffusivity of a polymer type. For a given plastic this means that the mobility of a migrant decreases with increasing molecular weight. For a given molecule this means that its mobility in different polymers is dependent on the elasticity or thermoplastic properties of the polymer. Once a molecule has moved to and arrived at the interface between plastic and foodstuff, the extent of mass transfer into the food depends on its viscosity and, very crucially, on its fat content. Since most of plastic constituents do have a lipophilic rather than hydrophilic character, migration increases strongly with increasing fat content; and especially so in the case where the fat or oil represents the outer phase of the food matrix. The toxicologically relevant molecular weight range for migrants is considered to end at a molecular weight of 1000 daltons. Larger molecules are considered from a biophysical point-of-view not to be physiologically resorbed in the gastrointestinal tract.
288
Franz
In order to underpin these more general descriptive approaches to migration by appropriate physico-chemical arguments, the parameters controlling migration will be presented and discussed in more depth in the following chapter.
10.1.1 Parameters determining migration Besides the geometric dimensions of a given food/packaging system which influence migration, mass transfer from a plastic into food consists essentially of kinetic (diffusion in the polymer and foodstuff) and thermodynamic (equilibrium partitioning between packaging and food) factors. It is common practice in migration evaluations to start as a worst assumption with a total mass transfer scenario, using a case where the initial concentration of a migrant in the packaging is known. However, if this relatively simple calculation provides a scenario which exceeds a migration limit, then it is advisable and necessary to achieve further refinements to the total mass transfer approach by taking into account the effect of the partition coefficient K and considering the role of the diffusion coefficient D as important material-specific parameters for migration. The role of the partition coefficient K The value of the partition coefficient K of a substance between two phases depends mainly on the polarity of the substance and the polarity of the two media. Applying the rule "like dissolves like", when considering a plastic packaging material for instance for contact with an aqueous product, one would as a consequence select a non-polar polymer (e.g. polyolefin) that will not be attacked by water. In such a system strongly polar substances prefer the product phase and non polar substances prefer the packaging material. However, when filling a fatty product into the same hydrophobic polymer type, a completely different partitioning behaviour from polymer into foodstuff takes place. Values for the partition coefficient KP,&defined as the concentration ratio at equilibrium of a migrant in the polymer, cP,,, divided by that at equilibrium in the foodstuff or food simulant, cF,,, range over several orders of magnitude depending on the polarities of polymer involved, the food simulant and the nature of the migrant. For instance, the partition coefficient KP,F = cp,, / c F , ~for limonene, a nonpolar substance (hydrocarbon), in the LDPE/water system at 23 "C was found to be higher than 5000 (Chapter 9, Table 9-13). This makes it retained in the polymer, whereas a much more polar compound like cis-hexenol shows a much lower value of 0.33, causing considerable transfer into the water. Numerous experimentally determined KeF-values have been described (Piringer 1993). Also estimative approaches for calculating Kp,F-valueshave been published (Baner and Piringer 1991,1994). An important quantity which can be calculated at equilibrium conditions is the amount of substance migrated into the food or food simulant at equilibrium, mF.e. Provided that the migration potential in the polymer, i.e. the initial amount of migrant dissolved in the polymer, mp,o, is known then from mass balance calculations the following equation can be derived: (10-1)
Migration of plastic constituents
289
The volumes of the polymer material of the packaging and food simulant are given by Vp and VF, the contact surface area between the two phases is given by A and the layer thickness of the polymer (for single sided contact) is given by dp In general, the package to food ratio is Vp/VF << 1 so that at equilibrium for Kp.F 2 1 practically the entire quantity of potential migrants will be found in the simulant, i.e. mEe = mP,().However, if the potential migrant is much more soluble in the polymer than in the simulant, i.e. K ~ . F>> 1, then at equilibrium only a small fraction will have migrated into the simulant so that mF.e << mp.o.As a rule, this second case occurs for migration into aqueous foods and, as a consequence, leads to a much lower substance transfer than into foods containing fat where, as a rule, Kp,F 2 1. The role of the diffusion coefficient D in the polymer Since practically the entire amount of migrant in the polymer can migrate into a fatty food or fatty food simulant at equilibrium, the most important variables which control migration of the substance are the contact time t and the temperature T. It was found in numerous migration tests that the majority of measurements could be represented as being approximately proportional to the square root of time t and proportional to the initial concentration of migrant in the polymer, cP,().With the assumption that material transport obeys the laws of diffusion (Chapter 7) then the following equation can be applied to describe approximately the migration of a substance from a polymer into a food (simulant) for situations where mEt/ mEe 5 0.5: (10-2) Here DP is the actual diffusion coefficient of the migrant in the polymer with a homogeneous distribution of the migrant at an initial concentration cp.0. It must not be confused with the effective diffusion coefficient for the complete polymer/migrant/ contact medium system presented by (Till et al. 1983,1987). All influences of the food or other contact medium that lead to a reduction in the migration value resulting only from migration in the polymer are contained in the constant k I 1 in Eq. (10-2). The constant k is therefore a measure of the influence of factors that lie outside the polymer/migrant system and has by definition a value of k = 1 in the absence of such influences (e.g. for contact with ethanol and oil) as long as no polymer swelling takes place. A practical application of this equation is that for cases with k = 1, the actual diffusion coefficients of migrants in the polymer can be determined from kinetic measurement of mEt from systems with known or measured values for c ~ ,Afterwards, ~. these DP values can then be used to estimate the k values for other foods. It is also necessary to describe mass transport in the opposite direction in order to understand the migration processes occuring with the use of different simulants in migration testing. More specifically, this means the migration of substances from the food or simulant or the simulant itself into the polymer. In analogy to Eq. (10-2) the amount of a substance, mp,t,migrating into the polymer from the food or simulant during the contact time t can approximately be described by the following equation: (10-3)
290
Frnnz
Where cE0 is the initial concentration of the migrating component in the simulant. In contrast to Eq. (10-2) the partition coefficient K plays an important role here, where the sorption of component into the polymer is proportional to KP,~. It is necessary to discuss the following relationship to achieve a better understanding of the influence of a simulant on migration. The average migration distance made by the diffusing additive i in the polymer during time t should be designated xi and its diffusion coefficient be DP,i. Analogously, xj should be considered to be the distance which the migration front of the simulant has moved in the polymer during the same time t and Dp,, be the diffusion coefficient of the simulant in the polymer. From the theory of diffusion the following ratio for xi/xj can be derived: (10-4) Now, in the case of xi << xj then the polymer additive i will be “overrun” by the simulant before it can migrate out of the polymer. Depending on the solubility of the simulant in the polymer (Kp,jvalue), the migration behaviour of i will then be influenced in an accelerated way. In the case, however, that xi >> xj then the migration of i from the plastic is not influenced by the migration of the simulant. From the above equations (10-1 to 10-4) the following conclusions can be drawn with respect to the selection of a food simulant: 1. When significant interactions occur between fat or oil and a plastic (Piringer, 1990) two borderline cases must be distinguished: Case la): Di >> Dj which means that according to Eq. (10-4) the previously mentioned case occurs where xi >> xj and the migration from the packaging is not affected by the uptake of fat by the plastic. The migration of substances whose molecular weights are much less than that of triglycerides remains unaffected by the uptake of fat because, as a rule, the diffusion coefficient decreases with increasing molecular weight. The molecular weights of the triglycerides in question lie between approximately 600 and 1000. Substances with molecular weights up to and including this range can be considered to meet this assumption. Case lb): When Di << D, , then according to Eq. (10-4) migration in the polymer is controlled by the fat penetration meaning the sorbed fat leads to higher migration values (Vom Bruck et al. 1986). 2. For volatile food simulants with low molecular weights, e.g. heptane, iso-octane. ethanol, the relationship D i << D j is valid for practically all polymer constituents. However, here again, two borderline cases must be differentiated as well: Case 2a): If the partition coefficient of the simulant Kp,j = 1 (i.e. the simulant is well dissolved by the polymer) the amount of sorbed simulant mp,tof j is so large according to Eq. (10-3) that it causes severe swelling of the polymer. As a consequence, total extraction of the migrant i from the polymer takes place provided that the solubility of migrant in the simulant allows that. This is for example the case where iso-octane comes into contact with non-polar polyolefins. Case 2b): For KP,, << 1 the sorption of j is so low according to Eq. (10-3) that the Dp.i value and consequently the migration of migrant i is not significantly influenced. This is for example the case where polar ethanol comes in contact with non-polar polyolefins at normal test temperatures (up to 40°C). At higher temperatures the solubility of ethanol (as well as that of fat) increases in polyolefins. However, by dilut-
Migration of’plustic consririientx
291
ing the ethanol with water, the undesired increase in migration due to higher temperatures can be avoided and a situation with a diffusion control in the polymer according to case 2b) be achieved again (Piringer 1993). If one wishes to use a volatile simulant as a lower molecular weight alternative to the natural edible oils or synthetic triglycerides, then one must determine according to the above discussion whether the simulant belongs to case 2a) or 2b). In the case of 2a) a time factor (in a n accelerated sense) must be considered because of the extraction effect caused by swelling. This means a series of studies must be carried out to determine at which contact time according to Eq. (10-2) does the same mass transfer take place compared to oil or actual food. Moderate temperature increase can also be used at the same time as a further variable. In the case of 2b) the time factor does not need to be considered as long as the test temperature is the same or very similar for the simulant as it is for the oil.
10.1.2 Migration control methodologies Any migration control procedure must be linked either directly or indirectly to the measurement o r evaluation of the concentration of an undesired compound in a foodstuff migrating from a package under given food contact conditions. This concentration, cEt, represents the toxicologically relevant target parameter for any migration control methodology. This toxicological parameter , c ~ ,which ~ , can be measured, controlled or assessed in different ways must then be compared to relevant migration limits as set up by laws such as the Commission Directive 90/128/EEC or by (juridically non-mandatory but practically binding) recommendations such as the German BgVV (Bundesinstitut fur gesundheitlichen yerbraucherschutz und yeterinarmedizin, formerly BGA) system. In this context it should be remembered that migration limits as set up in the European Directives have been derived from toxicological data in connection with some conventional assumptions. The migration limit, expressed in milligrams per kilogram food (simulant), is calculated from the toxicological magnitudes AD1 or TDI (acceptable daily intake o r tolerable daily intake, each expressed as milligrams per kilogram body weight per day) by multiplication with the factor 60 which (in kilograms) is the conventionally assumed body weight of an average European person. It is further assumed that this average person eats 1 kg food per day which is packed by 6 dm2 plastic material (Ashby et al. 1997). It should be kept in mind that specific migration limits (SML) established in this way d o contain inbuilt safety margins in the range of 100 to 1000 relative to so-called “No toxic effect levels” (Katan 1996 a)). SML values range typically from the 10-20 pg/kg (ppb) level for specific substances of toxicological concern such as vinyl chloride, butadiene, acrylonitrile and others up to the lower mgikg (ppm) level for less toxic principals such as bisphenol A (3 ppm), ethylendiamine (12 pprn ) or I-octene (15 ppm) and others. On the other hand, food packaging legislation or regulation has also set up restrictions on the packaging material side. Especially, the above mentioned BgVV system is mainly built on this strategy of setting maximum allowable concentrations in the packaging material. Such compositional limits in plastics are given as QM (maximum quantity) limits in the minority of compounds listed by EU Directives, especially in such cases where the migrant is chemically not stable enough in food simulants or may bc lost in migration testing due to its volatility. A typical example is butadiene
292
Franz
which is listed in 90/128/EEC with both a SML value (not detectable) and a QM value of 1 mg/kg polymer. It has been the experience of many experimentators that the SM determination of butadiene in aqueous food simulants is practically impossible in a reliable and reproducible way. The reason for this practical difficulty is the high volatility of this compound and its very unfavourable (from a sample handling point of view) partition coefficient KP,F, estimated to be in the range of limonene or higher (see above). Both factors contribute to immediate and significant losses of butadiene from aqueous migration solutions during sample handling. Similar observations have been reported for other volatile migrants (Rijk 1993). The question by which test methodology migration should best be controlled cannot be answered by recommending only one and the same test principle for all cases. Nowadays a number of options, including mathematical modelling of diffusion processes, are available and all of them can be justified for application under certain circumstances. However, as a general strategy, it is wise not to start in all cases of compliance testing immediately with a specific migration test but to consider the materialrelated, geometric and time-temperature application parameters of the individual food/packaging system to be evaluated. More specifically, it is wise to consider the migration potential of a given migrant in a plastic before initiating a long-term and time-consuming migration test. Or with other and more simplistic words: Initial considerations to any compliance testing should always start with the question “Can a given migration limit be exceeded or even reached at all?”. The second consideration should then address the question “What is the most economic way to demonstrate that a migration limit cannot be exceeded?”. This however goes without saying that it must not be the expectation of any compliance test that migration limits cannot be exceeded. Undoubtedly, the relevant maxim is “Consumer’s safety must not be compromised”. However, also undoubtedly, this approach helps to economise migration control and to allow more tests per unit of time and cost - a principle which has been proven to increase consumer safety. In the following, several options for migration control testing are described briefly with a focus only on the essential parts of each strategy. The options are given in a sequence which tries to meets in the best way the considerations made above.
Indirect migration assessment by compositional analysis of plastics Assessment by worst-case assumptions of total mass transfer Quantitative determinations of migrating analytes in food simulants and especially in the more complex matrices such as olive oil or other fatty simulants or foodstuffs themselves in many cases require relatively time-consuming sample preparation and very sensitive and selective methods of analysis. So the a priori most reasonable way is to carry out a compositional analysis in the plastic to determine the initial concentration of a migrant in a polymer, c ~ ,This ~ . value is equivalent to the migration potential and can be assessed in different ways with respect to the corresponding specific migration (SM). The most simplistic and direct approach is to assume total mass transfer into a foodstuff or simulant and compare this worst-case value with a given SML restriction. Vice versa, a given SML restriction can be transformed into a corresponding QM value, again under the assumption of total mass transfer, and compared to the
Migration of plastic constituents
293
experimentally determined c ~ ,This ~ . represents the worst-case modification of socalled QM/SML relationships (Baner et al. 1996) and does not take any partitioning or kinetic effects into account. Conventionally, QM/SML or cp.$3M ratios of 100 have been assumed and even implemented in the legislation - as an example the European vinyl chloride restrictions of QM = lmg/kg and SML = not detectable at 0.01 mg/kg may be cited. However, even under total mass transfer assumptions, the thickness of the respective polymer layer must be taken into account. It is obvious that for very thin film thicknesses a measured cP,(]value may exceed a given QM value without posing any health risk to a consumer. With other words, the cp,,JSML ratio is a function of the film thickness and for very thin films may end up at ratios orders of magnitude higher than the conventional one of 100 (compare also Figure 10-l)(Baner et al. 1996). And this, to be well remembered, under the assumption of total mass transfer. Since these relationships have been recently demonstrated (Franz and Rijk 1997) and specifically in the case of coatings and laquers on metal substrates, another understanding and definition of QM values has been developed. What is meant here, are area-related QM values where the maximum allowable migration is given as mass [mg] of migrant per food contact area [dm’] of the packaging. This new approach, which is currently being introduced into European legislation (EU Commission 1999), is extremely helpful especially in those cases where film thicknesses cannot be determined. In all cases under the premise of total mass transfer where an indirect migration assessment demonstrates the impossibility of exceeding a given legal SML restriction criterion, full compliance testing has been achieved and no further migration assessment or testing is necessary. Assessment by mass balance considerations under equilibrium conditions
In those cases where the above assessment leads to an uncertain conformity status, then mass balance calculations can be applied according to Eq. (10-1) provided that reliable values for the respective partition coefficient Kp,F are known. Figure 10-1
K = 1000
K = 100
K=10 K= 1 0
50
100
150 dp
(w)
200
250
300
Figure 10-1: QM/SML ratio versus laver thickness dp as a function of the partition coefficient KP,F under equilibrium conditions.
294
Franz
shows a set of generalized curves presenting calculated QM/SML values versus the layer thickness dp as a function of the partition coefficient and assuming a constant surface area to mass food ratio of 6 dm'lkg. One important relationship evident from this figure is that the variations of the partition coefficient over a range from 1 to 10 (typical for partitioning of substances between polymers and fats or oils) has no significant effect on the migrated amount. Furthermore, for a partition coefficient range from 1 to 100, there is a large effect of material thickness on the migration whereas for K , , > 100 the curve becomes practically insensitive to the material thickness (Baner et al. 1996) Assessment by application of complex mathematical models
As described in Chapters 7, 11 and 15 of this book predictive mathematical models for migration estimation based on diffusion theory and considering partitioning effects have been developed in the past few years. Although such models are currently still under scientific discussion (Reynier et al. 1999) and refinement or further development they have been proven in whole classes of polymer types such as the polyolefins to work very satisfactorily in terms of providing worse case migration scenarios. This is a prerequisite to finding general acceptance for being used in the field of food packaging compliance testing. The use of these diffusion models to progress the evaluation process of a food packaging plastic will be discussed shortly. In those cases where assessment by mass balance considerations under equilibrium conditions, including partitioning effects, does not provide a clear picture of the plastics conformity status, then the different diffusivities of polymer types and the influence of the migrant molecule size or its molecular weight on its mobility within a plastic can be taken into account to achieve more distinguished views on QM/SML ratios. Based on diffusion theory (Chapters 7 and 15) QM/SML ratios can be described as a function of the migrant molecular weight, for different polymer types as given in Fig. 10-2. For illustration reasons, this figure (Baner et al. 1996) provides two scenarios (i) diffusion controlled migration from different plastics under standard test conditions of 10 days/4O0C under the assumption of infinite thickness and (ii) as for given thicknesses (of any plastic) under the assumption of total mass transfer (KP.F=l). It can be recognised (again) that complete migration transfer calculations are dependent on the material thickness. It should also be noted that complete migration transfer lines are independent of migration test time and temperature conditions. Figure 10-2 shows that for some combinations of polymer type and thickness and substance molecular weight, there are cases where mass balance calculations yield higher QMlSML ratios than diffusion-controlled migration calculations. This is only a virtual contradiction and can be explained by the infinite thickness assumption of the diffusion model. This situation is particularly given in the case of high diffusion coefficients, i.e. high diffusivity of the plastic and/or migrants with low molecular weights. Figure 10-2 can be used to provide an acceptable estimated initial concentration of a substance in a polymer where a related SML value cannot be further exceeded. For example: a migrant with molecular weight 750 has a corresponding QM/SML value of approximately 1000 for the HDPE/PP curve. Now, multiplying this QM/SML value by the legally prescribed SML value will give its maximum acceptable QM in the polymer.
Migration of plastic constituents
i 4
l.e+7
295
Rigid PVC
I I .
/
l.e+6
I /
/
l.e+O t0
1
250
500
i Non-polyolefins JLDPE
-
750
1000 1250 1500
Molecular weight of migrant
Figure 10-2: QMlSML ratio versus molecular weight under standard test conditions (10 days/40 "C) for different polymer types under the assumption of infinite thickness as well as for given thicknesses under the assumption of total mass transfer.
Another attempt t o demonstrate the usefulness of employing diffusion models is made with Fig. 10-3. A dimensionless migration curve can be found for a given food packaging, to allow a quick look-up of possible migration values, for instance for plausability considerations related to measured migration test results or for the design of new plastics additives. This figure is based on the diffusion model presented in Chapter 15 and applies the migration Eq. (7-51) for an individually given food packaging application. It models the migration under standard test conditions of 10 days/40 "C as a function of cRo and the migrant's molecular weights from a HDPE container of thickness dp = 0.06 cm, assuming a surface/volume ratio of 6 dm2/kg and a partition coefficient KP,F= 1 (high solubility in the foodstuff). Analogous figures can be derived for any other food packaging application. With respect to the curve given in this figure, it should be noted that the packaging system under the applied test conditions can be considered nearly infinite or semi-infinite for migrants down to molecular weights of approximately 150. At lower molecular weights where the curve turns down from the steep line, the thickness of the material controls the shape of the migration curve. This particular situation can be considered an intermediate phase between infiniteness and mass balance as discussed above and presented in Fig. 10-2. As an example of how to make use o f Fig. 10-3, a migrant of molecular weight 47.5 may be selected; and the curve then provides a value of 0.5. If this migrant is, for instance, present in the polymer at C P , ~=~200 ppm then migration into the foodstuff can be calculated at 1.0 mg/kg from the equation given on the y-axis.
296
Franz
-
3,s
B
3
E
Y
0
2,5 e
=
9
2
Y
29
1,5
0
10 1 1
5
0,5
I
.v
$
V
0 0
100 200 300 400 500 600 700 800 900 1000
molecular weight of migrant
Figure 10-3: Estimation of migration (standard test conditions of 10 days/4O0C) as a function of CP,,) and in dependency of molecular weight of migrant from a HDPE container of thickness dp = 0.06 cm at a surfacelvolume ratio of 6 dm2/kg assuming a partition coefficient KP.F= 1.
Migration assessment by analysis of mass transfer from plastics Until today, the control of transfer from plastics packaging materials into foods has mainly been based on the measurement of the substance(s) in the food or simulant after certain specified, and in most cases standardized, contact conditions. Here, in principal, it can be distinguished between: (i) conventional direct migration measurements where a sample is placed in contact with a food or simulant in a manner representing the contact conditions of actual conditions in use; and (ii) alternative semi-direct migration test approaches where a sample is kept in contact with an appropriate simulant in such a manner that a strong interaction between simulant and plastic takes place (“more severe test conditions”) and - although shorter contact times are then applicable - at least equal or exaggerated extents of migration are obtained. Direct migration measurement The principle of direct migration measurement is, as the term reveals, to measure either directly in foodstuffs or more commonly mimic as closely as possible a given food packaging application, using agreed and authorised food simulants (Chapters 11 and 12). Results obtained with food simulants represent either directly the real rnigration values or can be correlated by the use of so-called reduction factors. The advantage of direct measurement is that the results can be directly and definitely compared with legally prescribed migration limits, thus allowing immediately a statement of conformity or disapproval of the test sample. The disadvantage of direct measurement has been recognised more and more during recent years: analysis of migrants in com-
Migration of plastic constititents
297
plex food simulants such as oils and fats is often very time-consuming and costly and at the same time relatively poor in terms of analytical sensivity and precision. This occurs not only in the case of specific migrants such as antioxidants or other non-volatile polymer constituents, but also in the case of overall migration determinations. It is extremely so in contact with oils as fatty food simulants and especially so in the case of high temperature testing and polar plastics. It should be noted that the legally allowed analytical tolerance in oils is stated at 20 mg/kg in relation to 60 mg/kg as the overall migration limit itself. This is really remarkable, taking into account that low diffusivity plastics such as PET release, as a rule, maximum overall migrations which are lower than the analytical tolerance itself. Overall migration testing, carried out according to the methods in the EN (European Standard) or ENV (European Prestandard) 1186 series of CEN (European Committee for Standardization) standards and described in numerous papers and books (Ashby et al. 1997; Katan 1996b; de Kruijf and Rijk 1988; CEN 1998a; Tice 1997), will not be taken up in detail here. Only the major problems related to overall migration testing in contact with oils will be mentioned here; these are: - inherent imprecision of the method due to substracting high values obtained by weighing the sample in order to determine a much smaller overall migration value; - moisture conditioning of polar plastics; - oil uptake by the sample and incompleteness of back extraction; - analytical determination of the absorbed amount of oil due to many possible GC/ FID interferences (according to the amendments of 90/128/EEC some 40 or 50 interfering compounds are in the positive list); - performance and handling at high temperature testing. Numerous examples of measured overall migration values have been collected and the interested reader can find a published data compilation summarized for different polymer types (Van Battum 1996). The whole area of specific migration determinations can be subdivided in two phases: (i) the pre-analytical migration exposure phase, which is more or less identical to that necessary for overall migration determination; and (ii) the pure analytical phase, where the specific migrant must be determined in the respective food or simulant as precisely and reproducibly as possible. This pure analytical migration test phase comprises many considerations to be made and includes so many technical possibilities that it deserves to be described in an own comprehensive section (see Section 10.2). Semi-direct, alternative migration tests The principle of these tests is to apply more severe test conditions by using volatile solvents with strong interactions towards the plastic, to enhance the migration rate from the plastic. Thus, the extraction test is based on an accelerated mass transport mechanism where the diffusion coefficients of migrants are increased by several orders of magnitude compared to the original migration test. As a rule, extraction tests are designed such that they make use of the following principle: I
Polar polymer
+ polar migrant + polar solvent
= worse case = non-polar polymer + non-polar migrant
+ non-polar solvent
I
298
Franz
Following this principle, semi-direct and generally quick extraction tests can be established with the aim of determining the migration potential for assessment of the worse case migration. These tests, which do not need to be as exhaustive as for instance necessary for a cp.0 determination, can be considered to be semi-direct because they produce an extraction value which can be directly compared to a legal restriction. But at the same time this value is an exaggerated one and does not always correspond to the real (lower) migration value. For example, a rapid extraction test for overall migration assessment into fatty food simulants, proposed as part 15 of the EN/ENV 1186 series of CEN standards, is presented as follows (CEN 1998b; Berghammer et al. 1994). The method is based on the determination of the extraction of migratable substances from plastics which are intended to come into contact with foodstuffs. It uses total immersion in non-polar isooctane and/or polar ethanol solvents depending on the polarity of the packaging material. According to results obtained by this method and taking physico-chemical considerations into account, the obtained extraction efficiency was generally found to be equivalent to or higher than overall migration results obtained under these test conditions: 10 days at 40"C, 2 h at 70"C, 1 h at 100°C, 30 min at 121 "C and 30 min at 130 "C, as specified in Council Directive 82/711/EEC and its subsequent amendments. To ensure as complete as possible an extraction of the potential migrants requires a strong interaction, e.g. swelling, of the sample by the extraction solvent. For this purpose, iso-octane is used as an extraction solvent for plastics materials and articles containing non-polar food contact layers, such as polyolefins. For test samples with polar food contact plastics such as polyamide and polyethyleneterephthalate, 95 % (v/v) aqueous ethanol is used. For polystyrenes, plasticised PVC and other polymers where the identification or polarity of the polymer is not clear, two parallel extraction tests are conducted using both of the proposed extraction solvents and taking into account the higher value obtained as the relevant result. In the case of unsymmetric structures such as plastics laminates and co-extruded plastics, the nature of the food contact layer determines the selection of the extraction solvent(s). Table 10-1 gives an overview of the allocation of extraction solvents and test conditions to polymer types. Table 10-1: Use of extraction solvents and test conditions in relation to polymer types. Polymer type of the food contact layer
Extraction solvent
Extraction conditions
Polyolefines
iso-octane
24 hours at 40°C
Polyamides
9.5 % ethanol
24 hours at 40 "C
Polystyrene
iso-octane and 95 YO ethanol
24 hours at 40°C
Polyethylene terephthalate
95 YOethanol
24 hours at SO "C
Polyvinyl chloride (plasticised)
iso-octane and 95 Y' O ethanol
24 hours at 40 "C
Polyvinyl chloride (rigid)
95 %, ethanol
24 hours at 50 "C
In case of doubt or unknown
iso-octane and 95 TOethanol
24 hours at SO "C
The test principle is such that the extraction of migratable substances from a sample of the plastics is determined as the mass of non-volatile residue after evaporation of the solvent following immersion. Test specimens of at least 1 dm2 (single side considered) are immersed in the extraction solvent at the specified test conditions and then
Migration o f plastic constitirents
299
removed. The extraction solvent is evaporated to dryness, the mass of the non-volatile residue is determined and the result is expressed as milligrams per square decimetre of surface area of the test specimen. The measured value is compared to the overall migration limit given by Directive 90/128/EEC (and amendments) and taking the analytical tolerance of this method (1 mg/dm') into account. The rapid extraction test was primarily developed for flexible packagings less than 300 ym in thickness. However, if this extraction test is applied to materials with higher thickness than 300 pm and the result does not exceed the allowed overall migation limit, then the material can be considered t o be in compliance with E C regulations. If the test result exceeds the allowed overall migration limit, regardless of the film thickness of the test material, then the extraction test may be repeated. However. in single-sided mode (using a test cell) or the conventional fat test or another alternative test may be used. In any case the rapid extraction test was designed to demonstrate compliance in the case of extraction values lower than the overall migration limit. The test cannot disapprove a material whose extraction value exceeds the limit. Conditions differing from those described above are of course possible as are much quicker tests. But in all cases, a reliable relationship between the short test and the full migration test must be established. In addition, it is also of practical and economic interest to design these tests so that they can be applied as broadly as possible, i.e. in most laboratories without too high an investment. Another quick extraction test has been proposed, especially tailored for rigid PVC material. Treating the samples with methanol for 2 hours under reflux conditions provided values which were considerably higher than those achieved under conventional olive oil conditions but still remained far below the overall migration limit, thus demonstrating fully legal conformity of the test materials (Tice and Cooper 1997). It should be noted here that quick cxtraction tests in general produce higher migration values and are therefore unfavourable when it comes to correlating such a value with the reputation of a test sample. However, when the testing costs can be decreased in this way by 50% to 70% and conformity can still be shown, although with somewhat higher results, then it seems to be only a question of getting accustomed t o extraction values. Substitute fat tests as defined by table 4 of E U Directive 97i48iEC are a further example of semi-direct migration tests. These tests are applicable in cases where technical or analytical difficulties are connected with the regular fatty food simulants. They apply iso-octane and 95 Oh ethanol under conventional test conditions such that an accelerated test based on (swelling) interactions between substitute test solvent and the polymer is conducted. For instance, an analytically impossible 10 daysi40 "C olive oil test on polyolefins can be replaced by a 2 days/2O0C extraction with isooctane. In this case a suitable time point has been chosen on the kinetic curve of an extraction process where an empirically satisfying agreement has been found between isooctane extractions and fat migration tests into olive oil. Another example is where a substitute test is carried out at lower temperatures compared to the required regular test temperatures. For instance, a high temperature fat test under test conditions of 2 hours/l5O0C can be replaced by a 3 hours/60"C iso-octane extraction. In this case again, a semi-direct test strategy is applied, empirically based on corresponding comparative test results. However, it is important to note that nearly all of these comparative long termlhigh temperature migration versus short terniflow temperature extraction measurements have focused more or less on just the overall migration and do not include sufficiently specific migrations. As a consequence, further research work is
300
Franz
necessary to correlate substitute test conditions for specific migration purposes where the chemical and thermal stability of migrants as well as the possible formation of break-down products and solubility questions related to individual migrants must all be taken into account.
10.2 Analysis of specific migrants 10.2.1 The positive list system within the European Union Legislation As described more in detail in Chapter 12, the European regulations on plastics for food contact are characterised by a consolidated positive list system which contains authorized monomers as well as additives for manufacturing or incorporation into any plastic type. This so-called “Plastics Directive” 90/128/EEC and its 5 amendments contain, as an essential element, numerous specific restrictions for listed substances either in terms of specific migration limits (SML values) and/or maximum quantities in the finished food contact material (QM values). Currently, out of approximately 200 listed monomers, nearly 80 are listed with a restriction, in most cases a SML value. Even more SML and/or QM values are expected for the additives’ list with restrictions, which was recently finalized at Commission level as a further (Sh)amendment of the “Plastics Directive” (EU Commission 1999). This situation immediately poses the question of enforcability of this law, since appropriate analytical methods have not been published or referenced in synchrony with the appearance of the positive list system. Although there is a general need for the availability of workable and validated analytical methods for food law compliance testing, the European Union legislative system requires special attention with respect to the analysis of specific migrants.
10.2.2 General requirements to analytical methods for compliance testing When selecting a method of analysis, some pre-considerations are obligatory. The volatility of the analyte must be taken into account as well as the nature of the matrix to be analyzed and, especially, the expected concentration range of the substance being measured. While analysis in aqueous food simulants and some plastics is relatively simple to perform, it is exceptionally difficult in many foods due to their complex chemical composition. As a result of these pre-considerations, a decision is taken about the choice of the most appropriate sample preparation procedure and a suitable chromatographic system. The envisaged analysis can also have various purposes or objectives. The aim may be to achieve a quantitative analysis (e.g. concentration determination) of one or several substances. The concentration range to be measured can be in the range of several mg/kg (ppm) or a few ng/kg (ppt). Analysis for the presence of groups of substances with defined structural characteristics (e.g. epoxides) or the identification of unknown substances may also be desirable. Already from these introductory notes, the very different structures of various analytical laboratories are becoming apparent. Analytical laboratories for small and medium-sized food packaging manufacturers and food producers, in general pay particular attention to the routine control of several substances and as a rule make use of a limited selection of methods. In contrast to this type of laboratory, governmental sur-
Migration of plastic constitiients
301
veillance laboratories, research institutes and central analytical facilities in industry are equipped with the latest state-of-the-art technology and are much more flexible in making use of any kind of analytical methods. Many analysts in these industry, private and public research, governmental and enforcement laboratories are involved in compliance testing of plastics for food contact. The methods applied may vary from sophisticated gaschromatography/mass-spectrometry (GUMS) techniques to classical methods like colorimetric determination. In many cases laboratories apply their own house analytical methods, often without any method validation. However, the use of different methods of determination will most likely lead to discrepancies in the results. In addition, for methods which have never been validated in inter-laboratory studies, no generally accepted analytical tolerances have been established. Consequently, enforcement of legal restrictions given by SML or QM values is poorly or even not possible at all, if validated and generally accepted methods are not available. However, in order to enable proper compliance testing, such methods of analysis commonly accessible and with well-defined analytical tolerances are indispensable. The requirements which must be addressed to analytical methods depend on their purpose. Routine methods for industrial quality control, for instance, need to be quick, cheap, robust and completely reproducible. It is not urgently required to determine a true value but to determine the homogeneity in manufacturing a certain industrial product. Therefore, the measurement of the corresponding parameter must be very precise, even though it may be wrong. On the other hand, very sophisticated, highly technical and expensive methods may be needed when it comes, for instance, to the determining the migration of a polymer constituent of analytically exotic character for the purpose of delivering a technical dossier for a petition to the authorities. In this case, the analytical method need not be cost-efficient in the first place but must provide a true value with high accuracy, or the best approach to it in order to allow decision-making about the need for toxicological testing. A complete intra-laboratory validation is another important requirement in this case. Due to the complexity of this specialised method it may never again find application in another laboratory, such as governmental surveillance methods. In between these two cases, however, the whole class of frequently used methods for food law compliance testing can be placed. Ideally, the major requirement here is: standardized methods should be published as norms and fully validated in inter-laboratory collaborative trials. However, being realistic and pragmatic, one has to recognize that realization of this demand will be more the exception than the rule. Furthermore, the methods should not be at the cutting edge of analytical hardware technology but make use of the state-of-the-art technology available in most analytical laboratories. Only under this premise, as much as possible will laboratories be able to apply the method, thus guaranteeing the most effective quality control and consumer protection. Generally, these methods should allow one to quantify the monomer or plastics additive at the required restriction limit in all relevant food simulants and/or in the polymer, respectively. That means an optimization in sensivity must be achieved, targeted to the necessary range of the method’s limit of detection (LOD), at or well below a given restriction criterion. It should be noted here that optimized methods of known performance and broad applicability with respect to food simulants as matrices may find their limit of workability when applied to real foodstuffs, due to interference problems. However, as a general rule, one can say that at least headspace sampling GC methods for volatiles are applicable and workable in every case.
302
Franz
10.2.3 Establishing (juristically) valid performance of methods The need f o r validated analytical methods It is generally recognized and accepted that analytical methods must be suitable for the intended use. Furthermore, EU Directives 85/591/EEC, 89/397/EEC and 93/99/ EEC state that analytical procedures for compliance testing with food laws are to be carried out on the basis of validated methods. Method validation is known as the process used to confirm that a procedure is fit for a particular analytical purpose. This process, an essential part of analytical quality assurance, can be described as the set of tests used to establish and document performance characteristics of a method. The performance characteristics of a method are experimentally derived values for the fundamental parameters of importance in assessing the suitability of the method (Horwitz 1988, 1995; Thompson and Wood 1993, 1995; Eurachem 1996; FA0 1998: US EPA 1995; US FDA 1993a). These parameters include:
Applica:bility:
Includes the matrix, analyte and species being measured, concentration ranges and the purpose for which it is suited, limitations of the method. Selectivity: The ability to discriminate between the target analyte and other substances in the test sample. Calibration: The calibration curve is a graphic representation of the detection system’s response as a function of the quantity of analyte. Accuracy: The closeness of agreement between a test result and the accepted reference or true value. Precision: The closeness of agreement between independent test results obtained under stipulated conditions. Range: The interval of concentration within which the analytical procedure demonstrates a suitable level of precision and accuracy. Limit of quantification: The lowest amount or concentration of analyte in a sample which can be quantitatively determined with an acceptable level of precision and accuracy. The smallest amount or concentration of analyte in a sample Limit of detection: that can be reliably distinguished, with stated significance, from the background or blank level. A measure of the magnitude of the response caused by a cerSensivity: tain amount of analyte. Ruggedness: The resistance to change of an analytical method when minor deviations are made in the experimental conditions of the procedure. Practica bility: The ease of operation, in terms of sample throughput and costs, to achieve the required performance criteria and thereby meet the specified purpose. Internationally accepted protocols have been established for the “full” validation of a method of analysis by collaborative trial (Horwitz 1988, 1995; I S 0 1994). These protocols require a minimum number of laboratories and test materials to be included in the collaborative trial to fully validate the analytical method. However, before
Migration ofplustic constituents
303
entering the ring trial, the method must undergo pre-validation within a single laboratory, normally the the one which develops or modifies the method. Inclusion of a second laboratory to confirm the performance obtained is another practise used for method pre-validation. Statistical tools for validation and evaluation of analytical methods Even when all conditions required for correctly carrying out an analysis are fulfilled, different values within a certain scatter range will be obtained within a laboratory for repeated measurements of identical samples. As a rule, the differences or scattering will be still larger if different laboratories are involved in the comparison exercise using identical samples. It is therefore necessary to apply statistical tools in order to verify the maintenance of limit values and eventually to evaluate the accuracy of disputed estimates. For this reason standards for measurement precision and accuracy are defined at national level (e.g. ASTM in U.S.A.,DIN in Germany) and at international level by I S 0 (International Organization for Standardization). Clearly, in view of the harmonization of the legal regulations in Europe, standardized methods of analysis and validation principles and certified reference materials are becoming more important. Moreover, due to the globalization of markets, these have worldwide relevance. A relevant juristical statement about the precision of a method can only be made after defining the performance characteristics obtained from a round robin or interlaboratory trial study, as for instance described in I S 0 5725 (IS0 1994). This study is used to determine the statistical key data about the precision of a method. The international standard I S 0 5725 has been adopted by many countries. I S 0 uses two terms, “trueness” and “precision”, to describe the accuracy of a measured value. “Trueness” refers to the closeness of agreement between the average value of a large number of test results and the true or accepted reference value. “Precision” refers to the closeness of agreement of test results, or in other words the variability between repeated tests. The standard deviation of the measured value obtained by repeated determinations under the same conditions is used as a measure of the precision of the measurement procedure. The repeatability limit “r” (an intra-laboratory parameter) and the reproducibility limit “R” (an inter-laboratory parameter) are calculated as measures of precision. Again, “precision” and “trueness” together describe the accuracy of an analytical method. Particularly important definitions and terms for the evaluation of analyses from I S 0 5725 will be briefly discussed in the following section. If the test result as an average of several individual measurements is obtained with the same method from an identical test sample, in the same laboratory, by the same analyst, with the same instrumentation, over a short period of time, then the study takes place under “repeatability” conditions. On the other hand, “reproducibility” conditions occur when the measurements take place following the same procedure and using identical samples but in different laboratories using different analysts with different instrumentation. The parameters describing the scattering of a test result under repeatability and reproducibility conditions are the corresponding standard deviations. The repeatability limit, “r”, is the within-laboratory precision and describes the maximum expected value of the difference between two individual test results obtained under repeatabil-
304
Franz
ity conditions at a defined significance which is in most cases a probability level of 95 %. Similarly, the reproducibility limit, “R”, describes the analogous between-laboratory precision. An important assumption for the use of r and R in practice is that they have been determined in an inter-laboratory test in which the participating laboratories represent those potential candidate appliers of the particular analytical procedure. For the determination of r and R, the method of analysis must be described very clearly and in detail to eliminate as many differences between laboratories as possible. Particular precautions are necessary with regard to the homogeneity and stability of the sample to be studied in the inter-laboratory test. Clearly the sample must withstand transport conditions and arrive unaltered at the participating laboratories. The statistical model for estimating the precision of the analytical method assumes that every individual measurement result y is the sum of three components: y=m
+B+
(10-5)
e
Here m represents the average of all values for the material studied (the characteristic level), B is the scattering between the laboratories and e the random deviation in results occurring in every measurement. The characteristic level m must not necessarily agree completely with the true value. There may be a difference (m - my) from the true value due to a systematic error in the measurement procedure (bias). For contributions B and e, it is assumed that they approximately follow the normal distribution. Then the variance of B, var(B), is the variance between laboratories (02). This include the scattering between different analysts and different instruments. The variance of e, var(e), is referred to as the internal variance of a laboratory (o’,). The average of all the internal variances of the participating laboratories in an inter-laboratory test is expressed as the repeatability variance 0:.While r depends only on the repeatability variance, R is determined by the sum of the repeatability variances and the variance between all laboratories. The standard deviations of repeatability and reproducibility are given by or and OR = (0: + o : ) ~ ’and ~ it follows that: r = f 2 1 / 2 ~ , and R
=f
2’120,
(10-6)
The factor 2”* is based on the fact that r and R are related to the difference between two measurement results. For distributions which are approximately normal and in the case of not too small a number of measurements, the factor f does not vary much from 2 and one can use the approximate value of 2.8 for f .21‘2. Because in practice the true repeatability and reproducibility standard deviations are not known, they are replaced with estimated values s, and sR from the inter-laboratory study and one obtains then: r = 2.8 s, and R = 2.8 SR
(10-7)
The precision of a standard measurement method is expressed using the values of r and R. More specifically, the range of measured values (from ... to ...) or a typical result should be given together with the corresponding estimated value of the standard deviation s, and sR as well as r and R for the corresponding range. The precision of the analytical method can be verbally described as:
Migration of plastic c.on.~titiient.s
305
The difference between two individual measurement results, which an analyst obtained on the identical sample material with the same instrument within the shortest time span possible, will on average not exceed the repeatability limit r more than once in 20 cases, provided the measurement procedure has been correctly carried out. The difference between two individual measurement results, reported by two laboratories for identical sample material, will on average not exceed the reproducibility limit R more than one time in 20 cases provided the measurement procedure has been correctly carried out. For probability levels other than 95 %, the values for r and R must be multiplied by the factors in Table 10-2. Table 10-2 Factors to adapt r and R to various probability levels. Probability level P %
Factor
90
0.82
9s
1.00
98
1.16
99
1.25
99.5
1.40
Various critical difference parameters can be derived from r and R as illustrated by the following examples: In one laboratory two measurements are carried out.
In one laboratory two groups of measurements are carried out under repeatability conditions whereby the first group of nl measurements gives an average value of y1 and the second group of n2 measurements gives an average value of y2. With r being the repeatability limit (for two individual measurement results), the critical difference CTD~~(Y~ is -then: Y~)
(10-8) In the case of nl = n2 = 1 then by definition one obtains r as the critical difference.
Two laboratories conduct more than one measurement each. One laboratory carries out nl measurements with an average of y1 while a second laboratory obtains an average of y2 for n2 measurements. The critical difference between the two is then: r2 (I -
(1 0-9)
By definition, for the special case where nl = n2 = 1 the formula simplifies to R and for nl = n2 = 2 one obtains:
(10-10)
306
Franz
The mean value from one laboratory is compared with a given value. One laboratory has carried n measurements under repeatability conditions and obtained an average value y which is compared with a given value mo (e.g. a specific migration limit). Then one obtains the critical difference as:
& [R2 - r2 (e)] 112
Cr%(Ifl
- mol) =
(10-11)
The mean value of several laboratories is compared with a given value. A number of p laboratories have carried out ni measurements and obtained the average values yi (i = 1,2, ..., p). The overall mean value over yi, 7,is compared with a given value mo. One obtains the following expression for the critical difference:
'cyi
R2 - r2 (1 - ' C L)]1'2, = y= (10-12) (W' P i "i P i If, when making a comparison between two averages or between an individual value and a given value, the measured difference between two values exceeds the corresponding critical difference, then this deviation should be considered suspect. There could be a specific reason why the critical difference is exceeded and this should be rationalized. In particular, if the given or reference value is a true or correct value, then the suspected difference can point to a bias in the measured result. In the case that the given value is a specific migration limit then the critical difference evaluation system allows the decision whether a legal restriction criterion has been exceeded or not. CrD95(Jy - mu[) =
[
10.2.4 A practical guide for developing and pre-validation of analytical methods Validation of analytical methods -both in-house and standard methods - has been the focus of many scientific, industrial and regulatory activities and working groups (US EPA 1995; US FDA 1987,1993a; Wegschneider 1996). As a consequence, numerous parameters for method validation have been defined and recommended. However, there is no official or generally accepted guiding document such as an I S 0 standard available which de- and prescribes a sequence of individual working steps for the development and validation of analytical methods. In the following, a practical guide for a step-by-step procedure is presented to establish a validated method of analysis both for determination of a specific migrant in a food simulant and the residual concentration in a plastic. This procedure was first developed and then applied in a European project (Franz and Rijk 1997) and found to be very practical. It should be considered as a recommendation based on the great practical experience of the analysts involved. The development procedure consists of the following 8 steps: 1. Scope of the method
Basically, two types of method must be taken into account: Analysis of a specific migrant in a food simulant (SML-methods) - Analysis of a specific migrant in a polymer (QM-methods).
-
Migration of plnstic corzstitirents
307
Generally, the method to be developed should allow quantitative analysis of the analyte at the required restriction limit in all the official food simulants, including substitutes or alternatives and/or in the polymer, respectively. That means that for very low SML values which are assumed to be in the range of the detection limit, the aim should be to obtain a detection limit equal to o r even lower than the restriction criterion. For other, higher SML and QM values, the aim should be to obtain a detection limit at least ten times below the legal or self-defined restriction criterion. It should also kept in mind that the method description should provide the relevant intra-laboratory precision data (at the required SML/QM value) according to I S 0 5725 -(IS0 1094). The most suitable analytical methodology should be selected based on the required performance characteristics. A sound literature search is always of great help with respect to known methods for the respective analyte and matrices. In most cases the search results will not directly provide the method wanted but will allow the most likely successful analytical approach to be set up. In this context, pre-considerations should address the most appropriate sample work-up procedure as well as the suitable analytical separation and detection system. The question of direct analysis of the analyte o r a derivate formed after chemical reaction should be clarified. And finally, some thoughts should already be given to the question of chemical stability of the analyte in the given matrices under the applied conditions.
2. Setting up the chromatographic and detection system First of all, it should be noted by the reader that it is not within the scope of this chapter to give more background and details on analytical chemistry. The corresponding scientific knowledge and technical information have been described elsewhere (for instance Schomburg 1984; Lee et al. 1984; Chapman 1986 and many other lecture books). Having rationalized the most suitable analytical principle as a result from step 1, it is necessary t o demonstrate the adequate specifity and sensivity of the analytical system. This aim can be achieved by carrying out an initial feasibility study where the following points need in-depth consideration: - availability and purity of reference standards; - purity requirements for chemicals, reagents and solvents; - safety considerations; - selection of sampling and chromatographic instruments; - choice of separation column; - suitable detection system; - optimization of instrument parameters; - appropriate internal standard; - solvent to be used for preparation of stock and standard solutions. The feasibility exercise should include preparation of a concentrated (stock) solution as well as diluted standard solutions of various concentrations and establishing a first calibration curve. From the data obtained, preliminary conclusions should be drawn with respect to the approximate precision, its working range and limit of detection. Finally, the results should provide sufficient evidence with respect to the workability of the intended analytical approach. If the method appears inappropriate, it must be optimized by methodological improvements, instrument changes or applica-
308
Franz
tion of a completely different analytical technique. If no satisfactory improvements can be achieved, a possible way out of the problem may be through compromising the acceptance limits.
3. Preparation and measurement of calibration samples When the initial study has been sucessfully completed, the performance characteristics should be investigated. As a first step on this way, calibration samples should be prepared in order to prove the calibration with respect to fulfilling general acceptance limits for linearity and repeatability performance. Starting from two independent stock solutions, two sets of analyte calibration solutions should be prepared. The solutions should preferably consist of the same medium (i.e. either food simulant for SML methods or swelling/extraction solvent for QM methods) to be used for the final determination of the specific migration or the residual amount in the plastic. Since the method’s performance characteristics are to be established in relation to the intended use, it is not necessary to check the method’s linearity over the full range of the equipment. Therefore, at least five concentration levels are required spanning the given restriction criterion value from 0.1 x value to 2.0 x value, provided this is within the LOD. Solutions without any analyte (blanks) should be analyzed as well. In the case of standard addition procedures, five levels should also be analyzed spanning the QM restriction value by standard additions ranging from 0.5 x value to 5.0 x value. All calibration and blank samples should be measured in triplicate (three injections of one sample) and the calibration graph should be constructed by plotting the detection signal obtained for the analyte (preferably peak area rather than peak height) relative to that of the internal standard versus analyte concentration. With respect to the correlation coefficient obtained (usually “R”)from the - in most cases - linear regression line, a minimum value of R = 0.9996 should be defined as a general acceptance limit. Deviation from this minimum requirement to linearity should only occur in exceptional cases. On the basis of 95 % probability level, the corresponding confidence bounds should be calculated and the within-laboratory LOD determined according to Fig. 10-4. The statistical methodology may be taken from the literature, for instance (DIN 1994). The two independently prepared sets of calibration samples should coincide with the upper and lower confidence bounds as another general acceptance limit with respect to repeatability performance. Full statistical evaluation of the calibration graph provides useful data about the method’s performance characteristics over the applied calibration range such as the standard error of the procedure, sx, or the standard error of estimate, sy 4. Within laboratory (repeatability conditions) precision according to I S 0 5725
The precision of an analytical method is the degree to which individual determinations of a series of standards agree. Since in general only one laboratory is involved in the development of the method the precision, as determined by one laboratory by one operator over a relatively short time, is defined as repeatability “r” ( I S 0 1994; compare also Section 10.2.3). For determining “r”, the following procedure is recommended: SML methods: for conventional or alternative food simulants at least 6 samples should be prepared, having the same concentration at the restriction criterion (SML value). All the samples should be measured by at least double injections and the
309
Migration ofplastic constituents
Y ......-.................. standard error of the analytical procedure s, standard error of estimate s, calibration regression curve
4
concentration
A
LOD Figure 10-4: Calibration curve and relevant precision parameters.
detector signals obtained should be evaluated using the calibration graph established as described under 3 above. QM methods: for the analysis of polymer matrices, 12 samples should be prepared for headspace sampling technique or 6 samples for liquid injection, respectively. In each case the series of samples should be prepared in the polymer/swelling solvent system with all samples using the same concentration at the restriction criterion (QM value). Headspace samples are measured only once and liquid injection samples in duplicate. If possible, analyte-free polymer should be used here. Again the spiked concentrations should be verified by standard addition calibration procedure carried out as described above under 3. When conducting an additional series of measurements using only the swelling solvent as the matrix without polymer and comparing results to those obtained above, the influence of the polymer matrix on the detection of analyte can be investigated. From the results obtained the repeatability standard deviation “S,” as well as the repeatability limit “r” can be calculated on a 95 % probability level according to Eq. (10-13). r = 2.8 S,
(10-13)
In addition, the results can also be used to calculate the mean recovery % as (the ratio of measured concentrationhominal concentration) * 100 and its standard devia-
310
Franz
tion in the case of direct analyte determinations without any sample work-up. In cases where a sample work-up procedure such as extraction or chemical derivation has been applied, the mean recovery can be determined by comparing the detector response for the analyte signal after sample work-up with the response obtained from the appropriate standard dissolved in pure solvent.
5. Development of an appropriate confirmation procedure Whenever a measured value exceeds a certain threshold (an internally defined limit or a legal restriction criterion) then a confirmation procedure is recommended or even necessary. The purpose of confirmation analysis is to prove or disapprove the measurement result obtained by the usual analytical method. Generally, the difference from the confirmation procedure compared to the usual test method should be due to only either the use of a completely different separation column (with completely different retention behaviour) in the same detection system or the use of an alternative detection method with sufficient sensivity. For the latter case and especially for GC methods, the prefered procedure should be to apply analyte selective mass spectroscopy (MS) detection. In some cases, derivatisation of the analyte followed by MS detection can also be the method of choice. In the case of HPLC methods, different polarity of another column in connection with full exploitation of modern UV diode array detection systems may be useful to selectively allow confirmation of the analyte. It is extremely important to make sure that the confirmation procedure works at the restriction criterion level or other self-defined concentration limit!
6 . Stability check on stock and standard solutions Stability tests are understood to be time-dependent measurements of a stock and a standard solution at different temperature conditions, for instance at ambient temperature (approx. 22 "C), normal refrigerator conditions (2-8 "C) and at deep freezing temperatures (approx. -20 "C). Stability tests should always be carried out with the exclusion of light. Under these storage conditions, stock and standard solutions should be monitored for constancy of initial analyte concentration. This can be achieved by comparison against freshly pepared solutions. Storage time should be extended to at least three months or until a decrease of 50 % or more has been observed. Sampling frequency depends on the decrease rate of the solutions. It is wise to commence stability checks early enough when starting method development work. The aim here is to find out the optimum storage conditions and maximum practical storage time. Internal standards, if applied, should also be investigated.
7. Workability of the test method under practical conditions After successful completion of all the development steps described above, the analyst still cannot be sure that the developed method will work under realistic conditions. The workability of the method therefore has to be proved. There are two major reasons why this workability test has to be carried out: First of all, it should be demonstrated that the method is not affected by interferences migrating from the polymer matrix. Secondly, it needs to be clarified whether the analyte is stable under the contact conditions applied during the migration exposure, to avoid false-negative migration results. Therefore, a suitable plastic material containing a high residual level of the analyte under investigation should be available for the following experiments:
Migration of plastic constitiients
3 11
SML methods: The selected polymer sample should be brought in contact with the food simulants under the relevant time/temperature conditions. In general, a migration test applying the total immersion principle using olive oil and 15 % ethanol at test conditions of 10 days at 40°C is sufficient. The determination should be performed in triplicate with double injections for analysis of the food simulants. In cases where the analyte level in the migration solutions is found to be below the detection limit, the migration solutions should be fortified with the migrant at the restriction criterion level or some other concentration of concern and measured again. In parallel, to check for migrant stability in the migration solutions, the relevant food simulants should be fortified at the level of concern to ensure that it is sufficiently higher than the LOD. If the test level concerned is in the range of the LOD, then the threefold concentration should be applied. The food simulants spiked in this way should be stored under appropriate timeitemperature conditions and recovery of the analyte determined by cross checking against freshly prepared solutions. QM methods: Triplicate determination of the concentration of the analyte in the selected polymer sample should be performed by the standard addition procedure using the polymer/swelling solvent system. The comparison to a calibration curve of the analyte in the pure swelling solvent only allows significant polymer matrix effects to be recognized. Again the stability of the analyte in the swelling solvent should be studied by fortification at the QM concentration or other relevant level and determination of recovery under the applied swelling and polymer extraction conditions. 8. Method description and reporting
Once the method has been established and validated, it should be described in full detail such that it can be carried out by any other analyst. Besides the numerous experimental details relating to the chemicals, solvents and solutions used and the chromatographic parameters, important observations such as for instance the findings about the stability of standard solutions should be laid down appropriately in the method description as notes or remarks. But potential health risks to the analytical operator should also be addressed, for instance in a warning note at the beginning of the method description. The following structure of a method description, which was agreed upon as a CEN standard format, is a recommended example.
Foreword: 1. Introduction:
2. Scope: -3. Principle:
4. Reagents:
Optional paragraph explaining about the background or history of the method. This chapter gives a rationale why it was necessary to establish this method. In this section the range of applications for the method should be indicated. This paragraph summarizes the applied analytical principle, including sample preparation techniques. It is necessary to describe in full detail the origin and purity of chemicals and solvents, the preparation of stock and standard solutions or other solutions, such as the mobile phase in the case of HPLC analysis. In conjunction with a given set of analytical parameters, the chromatogram obtained or at least an indication of retention times obtained for the analyte and the internal standard should be presented.
312
Franz
5. Apparatus:
This chapter should describe the complete set of instrumental and other analytical parameters as well as special laboratory equipment and analytical accessories such as size and type of sample vials, pipettes and syringes etc., standard laboratory glassware and equipment excepted. 6. Samples: In this section, the preparation of test samples, blanks and calibration samples has to described, together with an indication of the minimum number of samples needed. If necessary, precautions should be mentioned, for instance to avoid cross-contamination of samples in the case of volatiles or to minimise chemical degradation in the case of unstable analytes etc. Here it is necessary to provide details as to how the analytical 7. Procedure: measurement of test, blank and calibration samples is executed and how the obtained data are evaluated. The measured concentration of the analyte obtained in this way may need further transformation into a different dimension and this should also be addressed in this section. 8. Confirmation: When a certain critical concentration value has been measured and found excessive, then it may be recommendable or even necessary to confirm the result or the identity of the quantified analyte by means of another analytical technique, for instance by specific detection using mass spectrometry. This confirmation procedure should be clearly presented in this paragraph. 9. Precision data: This chapter should give an insight into the validation procedure applied and report the most important performance characteristics: - the achieved limit of detection (LOD) or LOD range, - the achieved repeatability criteria, i.e. the r-values in the different food simulants or in the polymer matrix and the concentration range where they have been determined, - if available the determined reproducibility, i.e. the R-value and the critical difference, i.e. the CrD95-value, as obtained in the most usual situation, i.e. one laboratory carries out n measurements (Eq. 10-11). 10. Test report: The test report should contain all necessary documentation such as - date of analysis and reporting, - clear identification of the test laboratory and the responsible analyst, - analyte and method of test, including references, - sample details like origin and specification, type of food/simulant/material/article, reception date and storage conditions, - results expressed in mg analyte per kg food simulant or plastic material, - details of confirmation procedure, if any, and - reasons for modifications introduced into the test method, if any.
Migration of plastic constititents
3 13
10.2.5 Availability of (pre)validated methods in Europe About the economical impossibility of meeting the requirements of I S 0 5725 and the need f o r pragmatic solutions
Ideally, and strictly speaking also legally prescribed, the positive list system in Directive 90/128/EEC and its follow-ups would formally only be enforcable on the basis of fully validated analytical methods for specific migration determinations (compare discussion in Section 10.2.3). However, since full collaborative trials according to I S 0 5725 are very time-consuming and expensive and because of the large number of SML values to be validated, it is immediately quite obvious that achieving this ideal situation is an economical impossibility. In addition, the time frame to fulfill such a task would exceed the dimensions of any real life requirement. Furthermore, many of the positively listed plastics constituents obviously have such a low commercial relevance that the question of absurdity would also be raised in these cases. As a consequence, there is clearly a need for pragmatic solutions to this problem. Since provision of “fully validated” methods turns out to be impossible, certain minimum requirements to method validation should be agreed upon at an European level to produce so-called “generally agreed or accepted” methods. Possible ways out of the situation are in-house validation procedures carried out by one laboratory, which however has to fulfill generally agreed requirements for single laboratory validation and as a basic formal prerequisite needs an accreditation to EN45000 (Eurachem 1993). This strategy may be assisted by the definition of minimum requirements for test method precision based on the so-called Horwitz trumpet (Horwitz 1988,1995) which links repeatability to concentration. As an economic alternative to I S 0 5725 and obeying full validation ring trials, small collaborative trials with two or three laboratories can also be considered. Currently, a task group (TG7) within CEN TC194/SCl is investigating the feasibility of such alternative approaches. Among the criteria to be considered, the aspects of practicability and cost-efficiency have also been selected. About the availability of generally accepted or standard methods in Europe In the European Member States there are many laboratories such as research organisations, industry, private, governmental and enforcement laboratories, involved in the measurement of specific migration of monomers and additives from polymeric packaging materials into foods and food simulants. Most of these laboratories apply analytical methods developed by themselves and in most cases without appropriate validation. Dependent on the analytical equipment and level of education within the laboratory, the methods applied may vary from sophisticated and highly selective techniques such as GUMS to classical and often unspecific methods such as colorimetric tests. In other words: laboratories are currently far from applying generally accepted and validated test methods for the determination of specific migrations. As a consequence, the results obtained from different laboratories for a given migration test are likely to vary in such a way that comparable, accurate and precise migration results are hardly obtainable for supporting a successful argument in court. However, also from an economical standpoint viewing a free European market, the requirement of available and generally accepted test methods was and remains essential.
314
Frcrnz
Vinylchloride EU Directives:
As a consequence of ELI Directive 781142/EEC, which introduced a limitation of vinyl chloride monomer both as residual amount in final articles (QM: lmg/kg) intended to come into contact with foodstuffs and in migration to food (SML not detectable; LOD: 0.01 mg/kg), the corresponding necessary analytical methods were developed between several European expert laboratories and laid down as agreed methods in EU Directives 80/766/EEC and 81/432/EEC, respectively. This piece of the EU harmonization process was too time- and work-consuming to continue in this way. The vinyl chloride Directives therefore remain a unique feature in E U food packaging legislation since this was found to be impractical for generalization.
CEN TCI 94/SCl: Validation and standardization of analytical methods is a recognized basic task of the European Committee for Standardization (CEN). Within the CEN organisation, a working group, CEN TC 1941SC11WG2, has produced fully validated methods for 15 plastics monomers which have been published as European pre-norms (ENV) within the ENV 13130 series (CEN 1999). Whereas Part 1 of this multipart standard gives general guidance t o the specific migration test methodology prior to analysis of the specific migrant, the remaining seven Parts are pure analytical methods for the determination of monomers in food simulants or plastics. Table 10-3 gives an overview of the ENV13130 series. Table 10-3: Overview of CEN ENV13130 standard. No.
Title
Restriction
Part 1 Guide to the test methods for specific migration of substances from plastics into food and food simulants and the determination of substances in plastics and the selection of conditions of exposure to food simulants Part 2 Determination of terephthalic acid in food simulants
SML: 7.5 mg/kg
Part 3 Determination of acrylonitrile in food and food simulants
S M L not detectable. LOD: 0.02 mg/kg
Part 4 Determination of 1,3-butadiene in plastics
QM: 1 mg/kg
Part 5 Determination of vinylidene chloride in food simulants
SML: not detectable, LOD: 0.05 mg/kg
Part 6 Determination of vinylidene chloride in plastics
QM: 5 mg/kg
Part 7 Determination of monoethylene glycol and diethylene glycol in food simulants
SML (T): 30 mg/kg
Part 8 Determination of isocyanates in plastics: - 2,6-toluene diisocyanate - diphenylmethane-4,4'-diisocyanate - 2.4-toluene diisocyanate - hexamethylene diisocyanate - cyclohexyl isocyanate - 1 $naphthalene diisocyanate - diphenylmethane-2,4'-diisocyanate - 2,4-toluene diisocyanate dimer - phenyl isocyanate
QM (T): 1 mgikg (expressed as NCO)
Migrution o,f plastic constititents
3 15
BCR (S,M & T )project “Monomers”: During the period 1993-1996 a European project was conducted within the Standards, Measurements and Testing programme of DG XII. The scope of this project was to fill the tremendous gap in analytical methods by development and pre-validation of methods of analysis for 36 monomers selected from the “Plastics Directive” positive lists. The project was carried out by a European consortium of 13 laboratories from 9 different Member States, under the co-ordination of the “Fraunhofer-Institute of Process Engeneering and Packaging” (FhIVV) Freising, Germany, and the main partner “TNO-Nutrition and Food Research” Zeist, The Netherlands. From the 36 target monomers (see Table 10-4) the project has elaborated 33 pre-validated methods of analysis for the determination of the specific migration of a selection of monomers listed with a restriction in Directives 90/128/EEC and 92/39/EEC (Franz and Rijk 1997). Since it was the original intention of the project to establish the developed analytical methods as ENVlEN standards within the European Committee for Standardization (CEN), the project structure included the involvement of CEN, in particular the Technical Sub-committee CEN TCl94/SC1 “General chemical methods of test for materials intended to come into contact with food’. Within this CEN sub-committee a working group, WG2, “Methods of test for monomers” is active in which more than 25 European expert analysts in the field of specific migration are collaborating in order to develop and standardize specific migration test methods. As most of the project participants were involved in the work of CEN TC194/SCl/WG2, it was decided in agreement with the “Standards, Measurements & Testing” Programme and DG 111 (Industry) of the European Commission to consult and disseminate the project results to the CEN working group in order to allow the establishment of Europe-wide accepted and agreed test methods. The mechanisms of consultation and dissemination were the following: Before the practical project work started, the project participants were required to deliver for each of their assigned monomers a rationale about the intended analytical procedure. These rationales were then circulated to the CEN group for discussion and expert comment. Only after there was agreement in the CEN group did the practical work start. In t h e course of the project, the CEN group was continuously informed about progress. As soon as a method of analysis was experimentally completed within the project, a draft written in CEN format was circulated to the WG2 members for discussion at the next biannual meeting. In these meetings the methods were either directly approved by the working group as technically suitable for publication as pre-norms, or if necessary after inclusion of the given comments and proposals for amendments. Finally, however, it turned out that CEN WG2 was overloaded with standardization tasks within the funding of the EU mandate for this work. Therefore, the developed and WG2 agreed pre-validated methods of analysis could not be processed forward to EN/ENV standards. Taking the multi-national project structure and the above involvement of CEN TCl94/SCl/WG2 into account, the co-ordinators and all other project participants considered the methods presented (see Table 10-4) to be accepted as Europe-wide agreed analytical methods for specific migration determination of the respective monomers. The project consortium proposed the methods to the European Commission for recommendation as “generally agreed” or as “useful” methods of analysis for the Member States.
316
Franz
Table 10-4: Overview of BCR project “Monomers” methods of analysis. PM/-Ref. No.
Monomer
10120
Acetic acid, vinylester
10630
Acrylamide
0.01
12788
0.01
13480
11-Aminoundecanoic acid 1.3-Benzenedimethaneamine 2,2-Bis(4-hydroxyphenyl)propane
13510
2,2-Bis(4-hydroxyphenyl)propane,bis(2,3-epoxypropyl)ether
13000
Restriction [mgkg]
QM
SML 12
0.05 3 and
0.02
(BADGE) 136M)
3,3-Bis(3-methyl-4-hydroxy-phenyl)2-indolinone
13630
1.3-Butadiene
1.8 0.02
14200
Caprolactam
15
14230
Caprolactam, sodium salt
15
14380
Carbonyl chloride
15880
1.2-Dihydroxybenzene
6
15910
1,3-Dihydroxybenzene
2.4
15940
1,4-Dihydroxybenzene
0.6
15970
Dihydroxybenzophenone
6
16000
4,4-Dihydroxybenzophenyl
16150
Dimethylaminoethanol
16750
Epichlorohydrin
16960
Ethylenediamine
17005
Ethyleneimine
17020
Ethylene oxide
17260
Formaldehyde
18460
Hexamethylenediamine
6 18
12 0.01
15 2.4
18670
Hexamethylenetetramine
15
19540
Maleic acid
30
19960
Maleic anhydride
30
21490
Methacrylonitrile
0.02
22150
4-Methyl-1-pentene
0.02
22660
1-Octene
23050
1,3-Phenylenediamine
24010
Propylene oxide
25150
Tetrahydrofuran
25360
Trialkyl (C5-Cl5) acetic acid. 2.3-epoxypropylester
25420
2,4,6-Triamino-1.3,5-triazine
25600
1,l.l -Trimethylolpropane
15
0.6 6 30 6
Migrution of plastic constituents
317
Methods of analysis in petitions to the European Commission: As another source of analytical methods for monomers and additives, the numerous technical dossiers submitted to the Scientific Committee of Food (SCF) through many European companies should be mentioned. According to the Commission’s request to the petitioners, these methods should have been written in a CEN standard format and meet current analytical requirements. Normally, however, these methods were established in assessing front line human exposure under the envisaged contact application, and were not always suitable for general control purposes. Nevertheless, there seems to be a large potential for technically suitable methods to be further evaluated and processed to a generally agreed level of validation on the Europe-wide scale.
10.2.6 Practical examples During method development and validation, a number of practical difficulties may occur and need control. An already well-known major phenomenon which can cause problems to the analyst is for instance insufficient or even zero recovery of analytes from the migration test solution. Possible reasons for that may be: (i) the chemical instability of analytes under migration test conditions due to oxidation, chemical binding to food simulant, (acid catalyzed) hydrolysis or ethanolysis; or (ii) volatilization during migration exposure and sample preparation (Rijk 1993). To illustrate and put into practise what has been said so far, several examples of methods of analysis are presented in the following, together with some specific difficulties and problems related to SM determination methods.
Acrylnnitrile ( S M L = not detectable at 0.02 nig/kg) The ENV13130-3 standard method (CEN 1999) to determine the specific migration of acrylonitrile in food simulants and foodstuffs originates from the German official BgVV (former BGA) collection of analytical methods according to $35 LMBG. It was already fully validated in Germany within a IS0 5725 collaborative trial before it was translated into English and editorially rearranged to fit into the CEN standard format. Acrylonitrile, CH2=CH-CN (CAS No. 107-13-1; PM/Ref. No. 12100) is a monomer commonly used as a co-monomer with styrene and butadiene to make ABS or SAN plastics for food contact articles such as kitchen utensils, rigid containers, measuring jugs, refrigerator linings, trays and fittings, coatings for nylon and polycarbonate films etc. It should be mentioned that acrylonitrile is a hazardous substance and volatile at room temperature. It requires corresponding precautions with respect to health risk for the analyst and cross-contamination during sample preparation. The method is not only applicable to the EU-official aqueous and fatty food simulant but also to foodstuffs such as beverages and soft margarine. Indeed the collaborative trial included fruit juice, wine and sunflower oil. The level of migrated acrylonitrile is determined by headspace gas chromatography, preferably with automated sample injection and using a nitrogen specific detector, for instance an alkali flame ionization detector (AFID). This gives the method the necessary sensivity to meet the
318
Franz
restriction criterion requirement “not detectable at 0.02 mg/kg”. Quantification is achieved using propionitrile as an internal standard with calibration against a blank sample matrix fortified with defined amounts of acrylonitrile. Numerous suitable G C columns are described in the method, for instance: - 2 m x 3 mm internal diameter stainless steel column packed with 15 YOpolyethylene glycol 1500 on 60 mesh to 100 mesh diatomite support; or - 12 m x 0.20 mm internal diameter, fused silica capillary column with 0.33 pm film thickness of free fatty acid phase (modified polyethylene glycol). In the case of a measured concentration exceeding the restriction criterion, confirmation of acrylonitrile levels is carried out either by combined gas chroamtography/ mass spectrometry (GUMS) or by re-analysis on a second GC column of different polarity. It should be noted that the GUMS confirmation is considered more appropriate. The procedure makes use of the selected ion detection mode and quantifies acrylonitrile by monitoring the ions m/z = 53 for acrylonitrile and m/z = 55 for propionitrile. It is stated in the method that the level measured in this way shall be the true value which may be lower and in compliance again with legislation despite the initially determined value. Concerning the limit of detection (LOD), the collaborative trial revealed that the participating laboratories could achieve LODs in the range between 0.005 mglkg and 0.02 mglkg. So, in order to allow 95 YOof laboratories to achieve the same LOD, the upper limit, i.e. 0.02 mg/kg, was agreed as relevant for any laboratory. Based on the r (0.005 mg/litre) and R (0.011 mg/litre) values determined in the collaborative trial, a critical difference threshold CrDg5of 0.006 mg/litre can be derived for a duplicate determination in the same laboratory. Consequently, the restriction criterion “not detectable” must be considered to be exceeded when a laboratory measures a concentration higher than 0.026 mg/litre on the basis of a duplicate determination.
1,J-Butadiene ( S M L = not detectable at 0.02 mg/kg, Q M
= Img/kg)
Butadiene, CH2=CH-CH=CH2 (CAS No. 106-99-0; PM/Ref. No. 13630) is commonly copolymerized with styrene and acrylonitrile to make ABS or BS food contact plastics (for applications see acrylonitrile). Butadiene is a suspected carcinogen with extreme volatility (bp 4 . 5 “C) and low water solubility. This makes it very difficult to handle migration and calibration samples where the matrix is of highly aqueous character such as the aqueous food simulants. The Plastics Directive foresees 2 restrictions for this monomer. The reasons for that will be recognized after the following discussion. The method developed in the BCR project (Franz and Rijk 1997) to determine butadiene in all of the official food simulants and probably also in real foodstuffs was pre-validated by a collaborative trial with three laboratories. It was found appropriate in principle for the quantitative determination of butadiene at a range of 0.01 to 0.1 mg/kg in food simulants. Indeed the limit of detection was found to be in the range 4 to 9 pg/kg, thus being even in the worst case significantly lower than originally presumed when establishing the Plastics Directive limit of 0.02 mg/kg. The working principle is as follows: The level of butadiene in a food or food simulant is determined by headspace gas chromatography (HSGC) with automated sample injection and by flame ionisation detection (FID). Quantification is achieved using an internal standard (n-pentane) with calibration against relevant food simulant samples fortified with known amounts of butadiene. Confirmation of butadiene levels is car-
Migrotion of plastic constituents
319
ried out by combined gas chromatography/mass spectrometry (GUMS). In contrast to the acrylonitrile standard, it was agreed in the BCR project that the confirmation is qualitative in the sense that it should demonstrate the correct identity of the measured peak and the absence of interferences. If the G U M S analysis clearly indicates the absence of interferences, then the migration result as obtained by the HSGC/FID method is taken as the true value. In the case of interferences occurring, the peak area ratios of the specified ions obtained from the G U M S method are used to calculate the relevant butadiene level in the food simulant. During the method development and validation work in the project, severe problems had been observed with respect to volatilization of butadiene. Therefore, it is important and crucial to take the following into account when planning and designing a migration test: From migration experiments carried out at 10 days for 40°C it was recognized that irreproducibly considerable loss (up to 90 %) can result from volatilization of 1,3-butadiene when using aqueous food simulants. Just opening and closing vials containing calibration solutions caused significant headspace losses of the volatile analyte. which is due to very unfavourable partitioning from the aqueous phase to the head space. On the other hand olive oil samples were found to provide satisfactory recoveries, due to the much better solubility of butadiene in this non-polar matrix. As a consequence. migration exposure of plastic materials to an aqueous food simulant in a test cell o r glass container combined with sampling steps to prepare food simulant aliquots for analysis will most likely lead to irreproducible results due to uncontrollable loss of analyte. Of course, one can argue that this occurs also in real life with a food package. However, when thinking about reproducibility of analytical standard methods, such an argument must be excluded in the first instance but taken into account again when it comes to the interpretation or down-correction of a reproducibly measured analytical result obtained under conditions without uncontrolled analyte loss. This topic has been discussed many times so far but no concrete solution has been agreed. A very pragmatic solution to this problem could be to divide a specific migration result obtained under controlled conditions by a factor of two to take care of real life losses of analyte into the environment of a food package. Obviously, this kind of problem had been foreseen when the idea of two restriction types for butadiene was born. Indeed, compliance testing with respect to the QM limit of butadiene in plastic according the ENV13130-4 standard method which also originates from the German official BgVV (former BGA) analytical methods according to $35 LMBG, is in all cases highly recommendable since this method is much easier and straight-forward and therefore, much less error-prone.
BADGE ( S M L = not detectable at 0.02 mg/kg, Q M = lmg/kg) 2,2-Bis(4-hydroxyphenyl)propane-bis(2,3-cp~~xypropyl) ether o r bisphenol A diglycidyl ether (BADGE), C21H2404, (CAS No. 1675-543, PM/Ref. No. 13510) is commonly used as a bifunctional monomer or cross-linker in epoxy-based coatings very widely used in food contact applications such as lacquer coatings on food cans, plastic storage vessels e.g. wine vats, or in adhesives for laminates, printing inks and others. For the molecular structure of B A D G E and known reaction products in food simulants see Fig. 10-5 (Philo et al. 1997). The analyst who plans to carry out migration testing for B A D G E is often confronted with the question how to obtain a suitable B A D G E sample, since it is not
320
Franz
(4)
Figure 10-5: Molecular structures of BADGE and hydrolysisiethanolysis products: (1) Bisphenol A diglycidyl ether (BADGE);(2) Bisphenol A (2,3-dihydroxypropyl ether) diglycidyl ether (did-epuxide); (3) Bisphenol A di-(2,3-dihydroxypropyl ether) ( d i d - d i d ) ; (4) Bisphenol A (3-ethoxy-2-hydroxypropyl ether) diglycidyl ether (ether-epoxide); ( 5 ) Bisphenol A (3-ethoxy-2-hydroxypropylether) (2.3-dihydroxypropyl ether) (ether-did).
commercially available on the market of fine chemicals. For this purpose, the analyst may contact national or international reference collection systems as for instance the “Plastics Reference Collection” of the British MAFF Central Food Science Laboratory in Norwich (Bush et al. 1994) which has been established largely within a BCR project funded by the European Commission. On request, this collection provides a 1 g reference standard or solution free of charge to the applicant. Many studies have been published describing the isolation and determination of BADGE monomer from polymer articles, oils or foodstuffs. A number of these papers also give attention to the formation of hydrolysis or other reaction products of BADGE (Roubtsova et al. 1997, Simal Gandara et al. 1993, Paseiro Losada et al. 1993). The BCR project has also provided Europe-wide agreed pre-validated methods both for QM and SML control purposes (Franz and Rijk 1997). The SML method: the scope of this method comprises the determination of BADGE monomer in all four of the official food simulants with a LOD of 0.005 mg/ kg. The method should also be applicable to other, alternative food simulants. The principle is to determine BADGE in aqueous simulant test samples directly by high performance liquid chromatography (HPLC) with fluorescence detection. Determination of BADGE in fat simulant is also conducted by HPLC, after isolating of BADGE from the oil by extraction using acetonitrile. The identity of BADGE may be confirmed either from its fluorescence emission spectrum (1st option) or from the ratio of the areas of its peaks in chromatograms obtained with fluorescence and ultraviolet detection (2nd option), in both cases by comparison with authentic samples. A third option is to use an analytical column with a different selectivity. Although the method was found to be applicable in all food simulants, the observed rapid hydrolysis of BADGE must be taken into account. As expected, BADGE is sen-
Migration of plastic
constituents
321
sitive to hydrolysis in contact with aqueous foodstuffs (Paseiro Losada 1993), so special attention was given in this BCR project study to the stability of BADGE under usual migration test conditions such as 10 days at 40 "C. The formation of mono- and di-hydrolysis products is shown in Fig. 10-5. These investigations were carried out using food simulants spiked in the restriction value range (0.02 to 0.04 mg/kg) and it was found that BADGE was completely hydrolyzed in all the three aqueous food simulants after 10 days at 40°C. On the other hand quantitative recovery was obtained in the case of olive oil under the same test conditions. A kinetic study revealed the following approximate half-lives in aqueous food simulants under the conditions mentioned above: Table 10-5:Hydrolysis of BADGE in aqueous food sirnulants at 40 "C. Food simulant
Half-life time
Distilled water
1.1 days
3 % (wlv) Acetic acid
0.15 days
15 % (vlv) Ethanol
I .4 days
Therefore, the scope of the method seems to be limited only to very short and mild contact conditions in the case of aqueous food simulants, but the method is fully applicable to olive oil and other oils or fats as well as to non-proton-active alternative simulants such as iso-octane. It is important to note that the above study was carried out under the premise of a given SML restriction of 0.02 mglkg. From this, a highly challenging situation existed with respect to the target detection limit. In the meantime the Scientific Committee on Food (SCF) for the Commission has updated its opinion on BADGE (Internet: http://europa.eu.int/en/comm/spc/spc.html). According to this opinion, the restriction included in the Shamendment of the "Plastics Directive" now reads: " S M L = lmg/kg in foodstuffs or in food simulants or Q M ( T ) Irng/6dm2 in FP Both limits shall include the mono-hydrolysisproduct of BADGE, if any. However in aqueous food sirnidants, the S M L should also include the di-hydrolysis product unless the material or article is labelled for use in contact with those foods and/or beverages for which it has been demonstrated that BADGE and its mono-hydrolysisproduct cannot exceed I mg/kg. Since it is also reported in the above SML method that the HPLC method after some modification also allows the detection of two BADGE hydrolysis products, the method may nevertheless be very useful to fulfill the latest regulatory requirements. The QM method: This describes the determination of BADGE monomer in polymers expressing the measured levels as (mg BADGE)/(kg of polymer) or as (mg BADGE)/(dm* food contact area) depending on the type of test material. BADGE is extracted from the polymer with refluxing chloroform and determined by high performance liquid chromatography (HPLC) with fluorescence detection after transfer from chloroform into 90 % (v/v) methanol to obtain a solution compatible with the HPLC mobile phase (acetonitrile/water = 65:35 (v/v)). Quantification is achieved relative to external standards. Confirmation of the identity of BADGE is achieved in the same way as described for the SML method. This is appropriate for the quantitative determination of BADGE at a minimum level of 0.15 mg/kg in the polymer.
322
Frcmz
The method development work was done under the premise of a BADGE QM restriction of 1 mg/kg. However, BADGE is mainly used in coatings on non-plastic supports. Therefore, the amount of coating on a final article (e.g. coated can) can generally not be determined with sufficient accuracy. Consequently, this leads to severe problems with respect to determining the QM restriction in mg/kg coating. Therefore, the idea of determining a surface area related BADGE “concentration”, in mg BADGE per dm2 food contact area was born and followed in this project work. Indeed, as mentioned above, the SCF has now proposed a surface area related QM value of 0.16 mg BADGE per dm2. The method already takes account of this situation and is capable of meeting the most recent BADGE QM restriction. In spite of the fact that two very suitable test methods were available for BADGE determination in food simulants, the need for a sensitive and convenient control method for real foodstuffs was not yet satisfied. This need originated from the socalled BADGE problem observed first in Switzerland (Biedermann et al. 1996) and then in many European countries. Control laboratories found BADGE very frequently exceeding the legal restriction values in samples drawn from the market. It is well known in the area of analysis of complex matrices such as foodstuffs that one of the major problems and in many cases an insurmountable difficulty arises from possible analytical interferences from the oily or fatty foodstuff matrix. In principal, a possible way-out of this problem is application of (i) a separation system which allows elution of the interesting analyte fraction separate from that of the oil matrix or (ii) very specific detection in the presence of oil matrix interference which allows compensation of poor chromatographic separation of the analyte fraction. The latter can be achieved in many cases by modern LC-MS-MS analysis using the atmospheric pressure chemical ionisation (ACPI) technique and operated in single reaction monitoring mode (SRM). Based on this technique, a rapid, convenient and very sensitive method for BADGE determination has been described for foodstuffs such as canned fish products and goulash soup and with general applicability to many other food types (Roubtsova et al. 1997). In t h e following, the HPLC fractionation of the analyte from a fatty matrix and selective MS-MS quantification is described in more detail. In order for the oil matrix fraction to by-pass the mass spectrometer (a Finnigan TSQ-7000), a 6-way-valve was installed after the C18 reversed phase HPLC column. The elution conditions were: Isocratic elution with 100 % methanol (MeOH) from 0-3 minutes. then 100 % tetrahydrofuran (THF) from 3-8 minutes and again 100 % methanol from 8-20 minutes. In this way the column was capable of separating the oil matrix fraction from the analyte fraction. The fraction containing BADGE was eluted from the column within the first 3 minutes during the MeOH elution, followed by the oil fraction being washed during the THF elution. While the column was THF-washed. the 6-way-valve was switched to pass the eluent flow to the waste reservoir in order to avoid the oil matrix entering the mass spectrometer.The mass spectrometer parameters were optimized for the most sensitive detection of BADGE possible. Under these conditions BADGE was detected in the MS mode as a molecular ion-water cluster m/z = 358.1 [M + H20]+ (see Fig. 10-6). In the coupled MS-MS mode a corresponding fragment ion with m/z = 191.0 (Fig. 10-6) was found to be the most intensive. For quantification in the applied SRM mode. only one parent ion ( d z = 358.1 [M + H201’) was selected for fragmentation and only one fragment ion (daughter ion m/z = 191.0) was detected. While in the MS mode both the analyte molecule ion and other matrix molecules with the
I mlz= 358.1
K+ 05 1.17
m/z = 191
1.K + O 3 0.41
I
Figure 10-6: Mass spectrum of BADGE [M + HzO] at n ~ / z= 358.1 (upper) and its fragment ion n?/z = 191 (lower) selected as daughter ion for SRM detection.
324
Franz
,
P.04
a.903
m/z = 358.1
9+04 3.961
I,
mlz = 191
Figure 10-7: Selective analysis of BADGE in a food sample: detection of the parent ion t d z = 358.1 in the MS mode (upper) and daughter ion d z = 191 in the MS-MS mode (lower).
Migration of plastic constituents
325
same m/z = 358.1 value are detected, the SRM mode detects only the specific BADGE fragment. In this way it was possible to detect BADGE very selectively in the HPLC analyte fraction. The advantage of detection in the SRM mode is illustrated by Fig. 10-7. The same sample of fortified “herring in vegetable sauce” was detected in MS mode, where the m/z =358.1 was monitored (Fig. 10-7: upper mass chromatogram), and in the SRM mode where the fragment m/z = 191.0 was monitored (Fig. 107: lower mass chromatogram). This demonstrates impressively how a selective detection procedure allows suppression of the matrix influence for unambigous detection and quantification of the analyte. In contrast, conventional HPLC/UV or HPLC/fluorescence detection systems will be disturbed in such a case by many interfering peaks originating from the food matrix. It may even be difficult or impossible to recognize the analyte peak, especially when there is no blank food sample (free of BADGE) available for comparison. The described HPLC-MS-MS method was also found to be capable of detecting selectively the BADGE hydrolysis and ethanolysis products in foodstuffs. This is highly advantageous over the BCR project SML method since it is much more suitable for meeting the analytical requirements derived from the updated SCF opinion on BADGE.
Carhonyl chloride ( Q M
= 1 rng/kg)
Carbonyl chloride, CI-C(=O)-C1, (CAS No. 75-44-5; PM Ref. No. 14380), also known as phosgene, is an important starting compound in the production of intermediates and end products in many branches of large-scale industrial chemistry due to its high chemical reactivity. Carbonyl chloride is mainly used for the production of diisocyanate